In combined mode, the driver is currently not setting RX and TX ring
numbers the same when firmware can allocate more RX than TX or vice versa.
This will confuse the user as the ethtool convention assumes they are the
same in combined mode. Fix it by adding bnxt_trim_dflt_sh_rings() to trim
RX and TX ring numbers to be the same as the completion ring number in
combined mode.
Note that if TCs are enabled and/or XDP is enabled, the number of TX rings
will not be the same as RX rings in combined mode.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new API HWRM_FUNC_RESOURCE_QCAPS provides min and max hardware
resources. Use the new API when it is supported by firmware.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for new firmware APIs to allocate hardware resources,
add a new struct bnxt_hw_resc to hold various min, max and reserved
resources. This new structure is common for PFs and VFs.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After SRIOV has been enabled and disabled, the MSIX vectors assigned to
the VFs have to be re-initialized. Otherwise they cannot be re-used by
the PF. For example, increasing the number of PF rings after disabling
SRIOV may fail if the PF uses MSIX vectors previously assigned to the VFs.
To fix this, we add logic in bnxt_restore_pf_fw_resources() to close the
NIC, clear and re-init MSIX, and re-open the NIC.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new __bnxt_close_nic() function to do all the work previously done
in bnxt_close_nic() except waiting for SRIOV configuration. The new
function will be used in the next patch as part of SRIOV cleanup.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The version has new firmware APIs to allocate PF/VF resources more
flexibly.
New toolchains were used to generate this file, resulting in a one-time
large diffstat.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently in the cases where cmp_type == CMP_TYPE_RX_L2_TPA_START_CMP or
CMP_TYPE_RX_L2_TPA_END_CMP the exit path updates cpr->rx_bytes with an
uninitialized length len. Fix this by adding a new exit path that does
not update the cpr stats with the bogus length len and remove the unused
label next_rx_no_prod.
Detected by CoverityScan, CID#1463807 ("Uninitialized scalar variable")
Fixes: 6a8788f256 ("bnxt_en: add support for software dynamic interrupt moderation")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements the changes needed for the bnxt_en driver to add support
for dynamic interrupt moderation per ring.
This does add additional counters in the receive path, but testing shows
that any additional instructions are offset by throughput gain when the
default configuration is for low latency.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In bnxt_vf_ndo_prep (which is called by bnxt_get_vf_config ndo), there is a
check for "Invalid VF id". Currently, the check is done against max_vfs.
However, the user doesn't always create max_vfs. So, the check should be
against the created number of VFs. The number of bnxt_vf_info structures
that are allocated in bnxt_alloc_vf_resources routine is the "number of
requested VFs". So, if an "invalid VF id" falls between the requested
number of VFs and the max_vfs, the driver will be dereferencing an invalid
pointer.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Venkat Devvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
flow_type in HWRM_FLOW_ALLOC is not being populated correctly due to
incorrect passing of pointer and size of l3_mask argument of is_wildcard().
Fixed this.
Fixes: db1d36a273 ("bnxt_en: add TC flower offload flow_alloc/free FW cmds")
Signed-off-by: Sunil Challa <sunilkumar.challa@broadcom.com>
Reviewed-by: Sathya Perla <sathya.perla@broadcom.com>
Reviewed-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-01-07
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add a start of a framework for extending struct xdp_buff without
having the overhead of populating every data at runtime. Idea
is to have a new per-queue struct xdp_rxq_info that holds read
mostly data (currently that is, queue number and a pointer to
the corresponding netdev) which is set up during rxqueue config
time. When a XDP program is invoked, struct xdp_buff holds a
pointer to struct xdp_rxq_info that the BPF program can then
walk. The user facing BPF program that uses struct xdp_md for
context can use these members directly, and the verifier rewrites
context access transparently by walking the xdp_rxq_info and
net_device pointers to load the data, from Jesper.
2) Redo the reporting of offload device information to user space
such that it works in combination with network namespaces. The
latter is reported through a device/inode tuple as similarly
done in other subsystems as well (e.g. perf) in order to identify
the namespace. For this to work, ns_get_path() has been generalized
such that the namespace can be retrieved not only from a specific
task (perf case), but also from a callback where we deduce the
netns (ns_common) from a netdevice. bpftool support using the new
uapi info and extensive test cases for test_offload.py in BPF
selftests have been added as well, from Jakub.
3) Add two bpftool improvements: i) properly report the bpftool
version such that it corresponds to the version from the kernel
source tree. So pick the right linux/version.h from the source
tree instead of the installed one. ii) fix bpftool and also
bpf_jit_disasm build with bintutils >= 2.9. The reason for the
build breakage is that binutils library changed the function
signature to select the disassembler. Given this is needed in
multiple tools, add a proper feature detection to the
tools/build/features infrastructure, from Roman.
4) Implement the BPF syscall command BPF_MAP_GET_NEXT_KEY for the
stacktrace map. It is currently unimplemented, but there are
use cases where user space needs to walk all stacktrace map
entries e.g. for dumping or deleting map entries w/o having to
close and recreate the map. Add BPF selftests along with it,
from Yonghong.
5) Few follow-up cleanups for the bpftool cgroup code: i) rename
the cgroup 'list' command into 'show' as we have it for other
subcommands as well, ii) then alias the 'show' command such that
'list' is accepted which is also common practice in iproute2,
and iii) remove couple of newlines from error messages using
p_err(), from Jakub.
6) Two follow-up cleanups to sockmap code: i) remove the unused
bpf_compute_data_end_sk_skb() function and ii) only build the
sockmap infrastructure when CONFIG_INET is enabled since it's
only aware of TCP sockets at this time, from John.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver hook points for xdp_rxq_info:
* reg : bnxt_alloc_rx_rings
* unreg: bnxt_free_rx_rings
This driver should be updated to re-register when changing
allocation mode of RX rings.
Tested on actual hardware.
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Use dma_zalloc_coherent for allocating zeroed
memory and remove unnecessary memset function.
Done using Coccinelle.
Generated-by: scripts/coccinelle/api/alloc/kzalloc-simple.cocci
0-day tested with no failures.
Suggested-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Advertise NETIF_F_GRO_HW in hw_features if hardware GRO is supported.
In bnxt_fix_features(), disable GRO_HW and LRO if current hardware
configuration does not allow it. GRO_HW depends on GRO. GRO_HW is
also mutually exclusive with LRO. XDP setup will now rely on
bnxt_fix_features() to turn off aggregation. During chip init, turn on
or off hardware GRO based on NETIF_F_GRO_HW in features flag.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most callers of rhashtable_walk_start don't care about a resize event
which is indicated by a return value of -EAGAIN. So calls to
rhashtable_walk_start are wrapped wih code to ignore -EAGAIN. Something
like this is common:
ret = rhashtable_walk_start(rhiter);
if (ret && ret != -EAGAIN)
goto out;
Since zero and -EAGAIN are the only possible return values from the
function this check is pointless. The condition never evaluates to true.
This patch changes rhashtable_walk_start to return void. This simplifies
code for the callers that ignore -EAGAIN. For the few cases where the
caller cares about the resize event, particularly where the table can be
walked in mulitple parts for netlink or seq file dump, the function
rhashtable_walk_start_check has been added that returns -EAGAIN on a
resize event.
Signed-off-by: Tom Herbert <tom@quantonium.net>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
After applying 2270bc5da3 ("bnxt_en: Fix netpoll handling") and
903649e718 ("bnxt_en: Improve -ENOMEM logic in NAPI poll loop."),
we still see the following WARN fire:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1875170 at net/core/netpoll.c:165 netpoll_poll_dev+0x15a/0x160
bnxt_poll+0x0/0xd0 exceeded budget in poll
<snip>
Call Trace:
[<ffffffff814be5cd>] dump_stack+0x4d/0x70
[<ffffffff8107e013>] __warn+0xd3/0xf0
[<ffffffff8107e07f>] warn_slowpath_fmt+0x4f/0x60
[<ffffffff8179519a>] netpoll_poll_dev+0x15a/0x160
[<ffffffff81795f38>] netpoll_send_skb_on_dev+0x168/0x250
[<ffffffff817962fc>] netpoll_send_udp+0x2dc/0x440
[<ffffffff815fa9be>] write_ext_msg+0x20e/0x250
[<ffffffff810c8125>] call_console_drivers.constprop.23+0xa5/0x110
[<ffffffff810c9549>] console_unlock+0x339/0x5b0
[<ffffffff810c9a88>] vprintk_emit+0x2c8/0x450
[<ffffffff810c9d5f>] vprintk_default+0x1f/0x30
[<ffffffff81173df5>] printk+0x48/0x50
[<ffffffffa0197713>] edac_raw_mc_handle_error+0x563/0x5c0 [edac_core]
[<ffffffffa0197b9b>] edac_mc_handle_error+0x42b/0x6e0 [edac_core]
[<ffffffffa01c3a60>] sbridge_mce_output_error+0x410/0x10d0 [sb_edac]
[<ffffffffa01c47cc>] sbridge_check_error+0xac/0x130 [sb_edac]
[<ffffffffa0197f3c>] edac_mc_workq_function+0x3c/0x90 [edac_core]
[<ffffffff81095f8b>] process_one_work+0x19b/0x480
[<ffffffff810967ca>] worker_thread+0x6a/0x520
[<ffffffff8109c7c4>] kthread+0xe4/0x100
[<ffffffff81884c52>] ret_from_fork+0x22/0x40
This happens because we increment rx_pkts on -ENOMEM and -EIO, resulting
in rx_pkts > 0. Fix this by only bumping rx_pkts if we were actually
given a non-zero budget.
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some dual port NICs, the 2 ports have to be configured with compatible
link speeds. Under some conditions, a port's configured speed may no
longer be supported. The firmware will send a message to the driver
when this happens.
Improve this logic that prints out the warning by only printing it if
we can determine the link speed that is no longer supported. If the
speed is unknown or it is in autoneg mode, skip the warning message.
Reported-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Tested-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcfm_dev always points to the correct netdev and we already
hold a refcnt, so no need to use tcfm_ifindex to lookup again.
If we would support moving target netdev across netns, using
pointer would be better than ifindex.
This also fixes dumping obsolete ifindex, now after the
target device is gone we just dump 0 as ifindex.
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Smatch warns that:
drivers/net/ethernet/broadcom/bnxt/bnxt_tc.c:160 bnxt_tc_parse_actions()
error: uninitialized symbol 'rc'.
"rc" is either uninitialized or set to zero here so we can just remove
the check.
Fixes: 8c95f773b4 ("bnxt_en: add support for Flower based vxlan encap/decap offload")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Small overlapping change conflict ('net' changed a line,
'net-next' added a line right afterwards) in flexcan.c
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2017-12-03
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Addition of a software model for BPF offloads in order to ease
testing code changes in that area and make semantics more clear.
This is implemented in a new driver called netdevsim, which can
later also be extended for other offloads. SR-IOV support is added
as well to netdevsim. BPF kernel selftests for offloading are
added so we can track basic functionality as well as exercising
all corner cases around BPF offloading, from Jakub.
2) Today drivers have to drop the reference on BPF progs they hold
due to XDP on device teardown themselves. Change this in order
to make XDP handling inside the drivers less error prone, and
move disabling XDP to the core instead, also from Jakub.
3) Misc set of BPF verifier improvements and cleanups as preparatory
work for upcoming BPF-to-BPF calls. Among others, this set also
improves liveness marking such that pruning can be slightly more
effective. Register and stack liveness information is now included
in the verifier log as well, from Alexei.
4) nfp JIT improvements in order to identify load/store sequences in
the BPF prog e.g. coming from memcpy lowering and optimizing them
through the NPU's command push pull (CPP) instruction, from Jiong.
5) Cleanups to test_cgrp2_attach2.c BPF sample code in oder to remove
bpf_prog_attach() magic values and replacing them with actual proper
attach flag instead, from David.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
short_input variable is assigned to another data pointer which is
referred out of its scope. Fix it by moving short_input definition
to the beginning of bnxt_hwrm_do_send_msg() function.
No failure has been reported so far due to this issue.
Fixes: e605db801b ("bnxt_en: Support for Short Firmware Message")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For flows that involve a vxlan encap action, the vxlan sock
interface may be specified as the outgoing interface. The driver
must resolve the outgoing PF interface used by this socket and
use the dst_fid of the PF in the hwrm_cfa_encap_record_alloc cmd.
Similarily for flows that have a vxlan decap action, the
fid of the incoming PF interface must be used as the src_fid in
the hwrm_cfa_decap_filter_alloc cmd.
Fixes: 8c95f773b4 ("bnxt_en: add support for Flower based vxlan encap/decap offload")
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While creating a decap filter the tunnel smac need not (and must not) be
specified as we cannot ascertain the neighbor in the recv path. 'ttl'
match is also not needed for the decap filter and must be wild-carded.
Fixes: f484f6782e ("bnxt_en: add hwrm FW cmds for cfa_encap_record and decap_filter")
Signed-off-by: Sunil Challa <sunilkumar.challa@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current 'bnxt_shutdown' implementation only invokes
'bnxt_ulp_shutdown' to shut down RoCE in the case when the system is in
the path of power off (SYSTEM_POWER_OFF). While this may work in most
cases, it does not work in the smart NIC case, when Linux 'reboot'
command is initiated from the Linux that runs on the ARM cores of the
NIC card. In this particular case, Linux 'reboot' results in a system
'L3' level reset where the entire ARM and associated subsystems are
being reset, but at the same time, Nitro core is being kept in sane state
(to allow external PCIe connected servers to continue to work). Without
properly shutting down RoCE and freeing all associated resources, it
results in the ARM core to hang immediately after the 'reboot'
By always invoking 'bnxt_ulp_shutdown' in 'bnxt_shutdown', it fixes the
above issue
Fixes: 0efd2fc65c ("bnxt_en: Add a callback to inform RDMA driver during PCI shutdown.")
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since day one of XDP drivers had to remember to free the program
on the remove path. This leads to code duplication and is error
prone. Make the stack query the installed programs on unregister
and if something is installed, remove the program. Freeing of
program attached to XDP generic is moved from free_netdev() as well.
Because the remove will now be called before notifiers are
invoked, BPF offload state of the program will not get destroyed
before uninstall.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Add ETH_RESET_AP support handling to reset the internal
Application Processor(s) of the SmartNIC card.
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) The forcedeth conversion from pci_*() DMA interfaces to dma_*() ones
missed one spot. From Zhu Yanjun.
2) Missing CRYPTO_SHA256 Kconfig dep in cfg80211, from Johannes Berg.
3) Fix checksum offloading in thunderx driver, from Sunil Goutham.
4) Add SPDX to vm_sockets_diag.h, from Stephen Hemminger.
5) Fix use after free of packet headers in TIPC, from Jon Maloy.
6) "sizeof(ptr)" vs "sizeof(*ptr)" bug in i40e, from Gustavo A R Silva.
7) Tunneling fixes in mlxsw driver, from Petr Machata.
8) Fix crash in fanout_demux_rollover() of AF_PACKET, from Mike
Maloney.
9) Fix race in AF_PACKET bind() vs. NETDEV_UP notifier, from Eric
Dumazet.
10) Fix regression in sch_sfq.c due to one of the timer_setup()
conversions. From Paolo Abeni.
11) SCTP does list_for_each_entry() using wrong struct member, fix from
Xin Long.
12) Don't use big endian netlink attribute read for
IFLA_BOND_AD_ACTOR_SYSTEM, it is in cpu endianness. Also from Xin
Long.
13) Fix mis-initialization of q->link.clock in CBQ scheduler, preventing
adding filters there. From Jiri Pirko.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (67 commits)
ethernet: dwmac-stm32: Fix copyright
net: via: via-rhine: use %p to format void * address instead of %x
net: ethernet: xilinx: Mark XILINX_LL_TEMAC broken on 64-bit
myri10ge: Update MAINTAINERS
net: sched: cbq: create block for q->link.block
atm: suni: remove extraneous space to fix indentation
atm: lanai: use %p to format kernel addresses instead of %x
VSOCK: Don't set sk_state to TCP_CLOSE before testing it
atm: fore200e: use %pK to format kernel addresses instead of %x
ambassador: fix incorrect indentation of assignment statement
vxlan: use __be32 type for the param vni in __vxlan_fdb_delete
bonding: use nla_get_u64 to extract the value for IFLA_BOND_AD_ACTOR_SYSTEM
sctp: use right member as the param of list_for_each_entry
sch_sfq: fix null pointer dereference at timer expiration
cls_bpf: don't decrement net's refcount when offload fails
net/packet: fix a race in packet_bind() and packet_notifier()
packet: fix crash in fanout_demux_rollover()
sctp: remove extern from stream sched
sctp: force the params with right types for sctp csum apis
sctp: force SCTP_ERROR_INV_STRM with __u32 when calling sctp_chunk_fail
...
Error code returned by 'bnxt_read_sfp_module_eeprom_info()' is handled a
few lines above when reading the A0 portion of the EEPROM.
The same should be done when reading the A2 portion of the EEPROM.
In order to correctly propagate an error, update 'rc' in this 2nd call as
well, otherwise 0 (success) is returned.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 32-bit architectures, rtc_time_to_tm() returns incorrect results
in 2038 or later, and do_gettimeofday() is broken for the same reason.
This changes the code to use ktime_get_real_seconds() and time64_to_tm()
instead, both of them are 2038-safe, and we can also get rid of the
CONFIG_RTC_LIB dependency that way.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We return on the previous line so this "return 0;" statement should just
be deleted.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change TC_SETUP_MQPRIO to TC_SETUP_QDISC_MQPRIO to match the new
convention.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ndo_xdp is a control path callback for setting up XDP in the
driver. We can reuse it for other forms of communication
between the eBPF stack and the drivers. Rename the callback
and associated structures and definitions.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent IRQ coalescing clean up has removed a guard-rail for the max DMA
buffer coalescing value. This is a 6-bit value and must not be 0. We
already have a check for 0 but 64 is equivalent to 0 and will cause
non-stop interrupts. Fix it by adding the proper check.
Fixes: f8503969d2 ("bnxt_en: Refactor and simplify coalescing code.")
Reported-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent refactoring of coalesce settings contained a typo that prevents
receive settings from being set properly.
Fixes: 18775aa8a9 ("bnxt_en: Reorganize the coalescing parameters.")
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This restores the original behaviour before the block callbacks were
introduced. Allow the drivers to do binding of block always, no matter
if the NETIF_F_HW_TC feature is on or off. Move the check to the block
callback which is called for rule insertion.
Reported-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix undefined symbols when CONFIG_VLAN_8021Q or CONFIG_INET is not set.
Fixes: 8c95f773b4 ("bnxt_en: add support for Flower based vxlan encap/decap offload")
Reported-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TC flower is not enabled on VFs and when there's no FW support.
Alloc the tc_info{} struct at init time only when TC flower is being
enabled.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements periodic querying of cfa flow stats
in batches to compute the 'lastused' attribute of TC flow stats.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add routines for issuing the hwrm_cfa_encap_record_alloc/free
and hwrm_cfa_decap_filter_alloc/free FW cmds needed for
supporting vxlan encap/decap offload.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds IPv4 vxlan encap/decap action support to TC-flower
offload.
For vxlan encap, the driver maintains a tunnel encap hash-table.
When a new flow with a tunnel encap action arrives, this table
is looked up; if an encap entry exists, it uses the already
programmed encap_record_handle as the tunnel_handle in the
hwrm_cfa_flow_alloc cmd. Else, a new encap node is added and the
L2 header fields are queried via a route lookup.
hwrm_cfa_encap_record_alloc cmd is used to create a new encap
record and the encap_record_handle is used as the tunnel_handle
while adding the flow.
For vxlan decap, the driver maintains a tunnel decap hash-table.
When a new flow with a tunnel decap action arrives, this table
is looked up; if a decap entry exists, it uses the already
programmed decap_filter_handle as the tunnel_handle in the
hwrm_cfa_flow_alloc cmd. Else, a new decap node is added and
a decap_filter_handle is alloc'd via the hwrm_cfa_decap_filter_alloc
cmd. This handle is used as the tunnel_handle while adding the flow.
The code to issue the HWRM FW cmds is introduced in a follow-up patch.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mapping of the ethtool coalescing parameters to hardware parameters
is now done in bnxt_hwrm_set_coal_params(). The same function can
handle both RX and TX settings. The code is now more clear. Some
adjustments have been made to get better hardware settings. The
coal_frames setting is now accurately set in hardware. The max_timer
is set to coal_ticks value.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current IRQ coalescing logic is a little messy. The ethtool
parameters are mapped to hardware parameters in a way that is difficult
to understand. The first step is to better organize the parameters
by adding the new structure bnxt_coal. The structure is used by both
the RX and TX sets of coalescing parameters.
Adjust the default coal_ticks to 14 us and 28 us for RX and TX.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a firmware internal reset after driver is unloaded.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some NICs have a firmware enforced maximum MTU setting by management
firmware. Set up netdev->max_mtu accordingly.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to call bnxt_approve_mac() which will send a message to the
PF if the MAC address hasn't changed.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code retrieves the firmware package version from firmware
everytime ethtool -i is run. There is no reason to do that as the
firmware will not change while the driver is loaded. Get the version
once at init time.
Also, display the full 4-part firmware version string and remove the
less useful interface spec version.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return -EINVAL if the length is zero and not proceed to do essentially
nothing.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Rob Miller <rmiller@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new PCIe device ID and chip number for bcm58804
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vxlan encap/decap filters are added to this firmware spec.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were quite a few overlapping sets of changes here.
Daniel's bug fix for off-by-ones in the new BPF branch instructions,
along with the added allowances for "data_end > ptr + x" forms
collided with the metadata additions.
Along with those three changes came veritifer test cases, which in
their final form I tried to group together properly. If I had just
trimmed GIT's conflict tags as-is, this would have split up the
meta tests unnecessarily.
In the socketmap code, a set of preemption disabling changes
overlapped with the rename of bpf_compute_data_end() to
bpf_compute_data_pointers().
Changes were made to the mv88e6060.c driver set addr method
which got removed in net-next.
The hyperv transport socket layer had a locking change in 'net'
which overlapped with a change of socket state macro usage
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving generic devlink code (registration) out of VF-R code
into new bnxt_devlink file, in preparation for future work
to add additional devlink functionality to bnxt.
Signed-off-by: Steve Lin <steven.lin1@broadcom.com>
Acked-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All drivers are converted to use block callbacks for TC_SETUP_CLS*.
So it is now safe to remove the calls to ndo_setup_tc from cls_*
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benefit from the newly introduced block callback infrastructure and
convert ndo_setup_tc calls for flower offloads to block callbacks.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hwrm_send_message() is replaced with _hwrm_send_message(), and
hwrm_cmd_lock mutex lock is grabbed for the whole period of
firmware call until the firmware DCB parameters have been copied.
This will prevent possible corruption of the firmware data.
Fixes: 7df4ae9fe8 ("bnxt_en: Implement DCBNL to support host-based DCBX.")
Signed-off-by: Sankar Patchineelam <sankar.patchineelam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In bnxt_find_nvram_item(), it is copying firmware response data after
releasing the mutex. This can cause the firmware response data
to be corrupted if the next firmware response overwrites the response
buffer. The rare problem shows up when running ethtool -i repeatedly.
Fix it by calling the new variant _hwrm_send_message_silent() that requires
the caller to take the mutex and to release it after the response data has
been copied.
Fixes: 3ebf6f0a09 ("bnxt_en: Add installed-package version reporting via Ethtool GDRVINFO")
Reported-by: Sarveswara Rao Mygapula <sarveswararao.mygapula@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In bnxt_sriov_enable(), we calculate to see if we have enough hardware
resources to enable the requested number of VFs. The logic to check
for minimum completion rings and statistics contexts is missing. Add
the required checks so that VF configuration won't fail.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCIE PCIE_EP_REG_LINK_STATUS_CONTROL register is only defined in PF
config space, so we must read it from the PF.
Fixes: 90c4f788f6 ("bnxt_en: Report PCIe link speed and width during driver load")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a further improvement to the PF/VF link change logic, use a private
mutex instead of the rtnl lock to protect link change logic. With the
new mutex, we don't have to take the rtnl lock in the workqueue when
we have to handle link related functions. If the VF and PF drivers
are running on the same host and both take the rtnl lock and one is
waiting for the other, it will cause timeout. This patch fixes these
timeouts.
Fixes: 90c694bb71 ("bnxt_en: Fix RTNL lock usage on bnxt_update_link().")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Link status query firmware messages originating from the VFs are forwarded
to the PF. The driver handles these interactions in a workqueue for the
VF and PF. The VF driver waits for the response from the PF in the
workqueue. If the PF and VF driver are running on the same host and the
work for both PF and VF are queued on the same workqueue, the VF driver
may not get the response if the PF work item is queued behind it on the
same workqueue. This will lead to the VF link query message timing out.
To prevent this, we create a private workqueue for PFs instead of using
the common workqueue. The VF query and PF response will never be on
the same workqueue.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of zeroing out bnxt_tc.c with a #ifdef foo, instead don't compile
the file when the option is not enabled. Now make and the preprocessor do
not have to waste time compiling a no-op.
Signed-off-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work enables generic transfer of metadata from XDP into skb. The
basic idea is that we can make use of the fact that the resulting skb
must be linear and already comes with a larger headroom for supporting
bpf_xdp_adjust_head(), which mangles xdp->data. Here, we base our work
on a similar principle and introduce a small helper bpf_xdp_adjust_meta()
for adjusting a new pointer called xdp->data_meta. Thus, the packet has
a flexible and programmable room for meta data, followed by the actual
packet data. struct xdp_buff is therefore laid out that we first point
to data_hard_start, then data_meta directly prepended to data followed
by data_end marking the end of packet. bpf_xdp_adjust_head() takes into
account whether we have meta data already prepended and if so, memmove()s
this along with the given offset provided there's enough room.
xdp->data_meta is optional and programs are not required to use it. The
rationale is that when we process the packet in XDP (e.g. as DoS filter),
we can push further meta data along with it for the XDP_PASS case, and
give the guarantee that a clsact ingress BPF program on the same device
can pick this up for further post-processing. Since we work with skb
there, we can also set skb->mark, skb->priority or other skb meta data
out of BPF, thus having this scratch space generic and programmable
allows for more flexibility than defining a direct 1:1 transfer of
potentially new XDP members into skb (it's also more efficient as we
don't need to initialize/handle each of such new members). The facility
also works together with GRO aggregation. The scratch space at the head
of the packet can be multiple of 4 byte up to 32 byte large. Drivers not
yet supporting xdp->data_meta can simply be set up with xdp->data_meta
as xdp->data + 1 as bpf_xdp_adjust_meta() will detect this and bail out,
such that the subsequent match against xdp->data for later access is
guaranteed to fail.
The verifier treats xdp->data_meta/xdp->data the same way as we treat
xdp->data/xdp->data_end pointer comparisons. The requirement for doing
the compare against xdp->data is that it hasn't been modified from it's
original address we got from ctx access. It may have a range marking
already from prior successful xdp->data/xdp->data_end pointer comparisons
though.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IS_ERR() already implies unlikely(), so it can be omitted.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for ingress-only qdisc for flower offload, as other qdiscs
are not supported for flower offload.
Suggested-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When bnxt VF-reps are not compiled in (CONFIG_BNXT_SRIOV is off)
bnxt_tc.c needs a dummy definition of the routine bnxt_vf_rep_get_fid().
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 2ae7408fed ("bnxt_en: bnxt: add TC flower filter offload support")
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to implement TC_CLSFLOWER_STATS TC-cmd and the
required FW code to query the stats from the HW.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the hwrm_cfa_flow_alloc/free() routines
that are needed to issue the FW cmds needed for TC flower offload.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for offloading TC based flow
rules and actions for the 'flower' classifier in the bnxt_en driver.
It includes logic to parse flow rules and actions received from the
TC subsystem, store them and issue the corresponding
hwrm_cfa_flow_alloc/free FW cmds. L2/IPv4/IPv6 flows and drop,
redir, vlan push/pop actions are supported in this patch.
In this patch the hwrm_cfa_flow_xxx routines are just stubs.
The code for these routines is introduced in the next patch for easier
review. Also, the code to query the TC/flower action stats will
be introduced in a subsequent patch.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The routine bnxt_link_bp_to_dl() is used to set the devlink ptr
in bnxt struct (bp) and also to set the bnxt back ptr in
the devlink struct. If devlink_register() fails, bp->dl must
be cleared which is not happening currently. This patch fixes
bnxt_link_bp_to_dl() to clear bp->dl by passing a NULL dl ptr.
Fixes: 4ab0c6a8ff ("bnxt_en: add support to enable VF-representors")
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce default rings from 8 to 4 on multi-port cards to reduce memory
usage.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we cannot allocate RX buffers in the NAPI poll loop when processing
an RX event, the current code does not count that event towards the NAPI
budget. This can cause us to potentially loop forever in NAPI if we
consistently cannot allocate new buffers. Improve it by counting
-ENOMEM event as 1 towards the NAPI budget.
Cc: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reported-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
initialize board_info values with proper enums for defensive programming
purposes. This will avoid any errors of the enums being declared not
lining up with the board_info array.
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add PCIe device ID for bcm58802 and bcm58808. Also add chip number
update to declare bcm588xx as chip class phase 4 and later
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides hints to irqbalance to map bnxt_en device IRQs
to specific CPU cores. cpumask_local_spread() is used, which first
maps IRQs to near NUMA cores; when those cores are exhausted, IRQs
are mapped to far NUMA cores.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the number of TX rings is changed (e.g. ethtool -L, enabling XDP TX
rings, etc), the current code tries to reserve the new number of TX rings
before closing and re-opening the NIC. If we are unable to reserve the
new TX rings, we abort the operation and keep the current TX rings.
The problem is that the firmware will disable the current TX rings even
when it cannot reserve the new set of TX rings. We fix it as follows:
1. Instead of reserving the new set of TX rings, just ask the firmware
to check if the new set of TX rings is available. There is a flag in
the firmware message to do that. If not available, abort and the
current TX rings will not be disabled.
2. Do the actual TX ring reservation in the path that opens the NIC.
We keep the number of TX rings currently successfully reserved. If the
number of TX rings is different than the reserved TX rings, we call
firmware and reserve again.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow APIs are added in this firmware interface.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_hwrm_func_qcaps() is called during probe to get all device
resources and it also sets up the factory MAC address. The same function
is called when SRIOV is disabled to reclaim all resources. If
the MAC address has been overridden by a user administered MAC
address, calling this function will overwrite it.
Separate the logic that sets up the default MAC address into a new
function bnxt_init_mac_addr() that is only called during probe time.
Fixes: 4a21b49b34 ("bnxt_en: Improve VF resource accounting.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Take back ownership of the MSIX vectors when unregistering the device
from bnxt_re.
Fixes: a588e4580a ("bnxt_en: Add interface to support RDMA driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the number of TX rings is changed in bnxt_setup_tc(), we need to
include the XDP rings in the total TX ring count.
Fixes: 3841340627 ("bnxt_en: Add support for XDP_TX action.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in a netdev_info message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of struct tc_to_netdev which is now just unnecessary container
and rather pass per-type structures down to drivers directly.
Along with that, consolidate the naming of per-type structure variables
in cls_*.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the return value from -EINVAL to -EOPNOTSUPP. The rest of the
drivers have it like that, so be aligned.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As ndo_setup_tc is generic offload op for whole tc subsystem, does not
really make sense to have cls-specific args. So move them under
cls_common structurure which is embedded in all cls structs.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the type is always present, push it to be a separate argument to
ndo_setup_tc. On the way, name the type enum and use it for arg type.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the phys_port_name for the external physical port to be in
"pA" format and that of VF-rep to be in "pCvfD" format as
suggested by Jakub Kicinski.
Fixes: c124a62ff2 ("bnxt_en: add support for port_attr_get and get_phys_port_name")
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the build error:
‘struct net_device’ has no member named ‘switchdev_ops’
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: c124a62ff2 ("bnxt_en: add support for port_attr_get and and get_phys_port_name")
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And define empty functions in bnxt_vfr.h when CONFIG_BNXT_SRIOV is not
defined.
This fixes build error when CONFIG_BNXT_SRIOV is switched off:
>> drivers/net/ethernet/broadcom/bnxt/bnxt_vfr.c:165:16: error: 'struct
>> bnxt' has no member named 'sriov_lock'
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: 4ab0c6a8ff ("bnxt_en: add support to enable VF-representors")
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a couple of warnings where variable ‘txq’ set but not used
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>v, i);
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes warning because location is u32 and can never be netative
warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suggested by Jakub Kicinski.
Fixes: c124a62ff2 ("bnxt_en: add support for port_attr_get and and get_phys_port_name")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the switchdev_port_attr_get() and
ndo_get_phys_port_name() methods for the PF and the VF-reps.
Using this support a user application can deduce that the PF
(when in the ESWITCH_SWDEV mode) and it's VF-reps form a switch.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the RX/TX and a simple netdev implementation
for VF-reps. The VF-reps use the RX/TX rings of the PF. For each VF-rep
the PF driver issues a VFR_ALLOC FW cmd that returns "cfa_code"
and "cfa_action" values. The FW sets up the filter tables in such
a way that VF traffic by default (in absence of other rules)
gets punted to the parent PF. The cfa_code value in the RX-compl
informs the driver of the source VF. For traffic being transmitted
from the VF-rep, the TX BD is tagged with a cfa_action value that
informs the HW to punt it to the corresponding VF.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a part of a patch-set that introduces support for
VF-reps in the bnxt_en driver. The driver registers eswitch mode
get/set methods with the devlink interface that allow a user to
enable SRIOV switchdev mode. When enabled, the driver registers
a VF-rep netdev object for each VF with the stack. This can
essentially bring the VFs unders the management perview of the
hypervisor and applications such as OVS.
The next patch in the series, adds the RX/TX routines and a slim
netdev implementation for the VF-reps.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In addition to the ETS weight, older firmware also requires the min_bw
parameter to be set for it to work properly.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report DCB_CAP_DCBX_LLD_MANAGED only if the firmware DCBX agent is enabled
and running for PF or VF. Otherwise, if both LLDP and DCBX agents are
disabled in firmware, we report DCB_CAP_DCBX_LLD_HOST and allow host
IEEE DCB settings. This patch refines the current logic in the driver.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For debugging purpose, it is sometimes useful to disable periodic
port statistics updates, so that the firmware logs will not be
filled with statistics update messages.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of duplicating the logic multiple times. Also, it is unnecessary
to zero the buffer in .get_ethtool_stats() because it is already zeroed
by the caller.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To allow users to set the hardware bridging mode to VEB or VEPA. Only
single function PF can change the bridging mode.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Retrieve and store the hardware bridge mode, so that we can implement
ndo_bridge_{get|set)link methods in the next patch.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VF representors and PTP are added features in the new firmware spec.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PF driver sets up a list of firmware commands from the VF driver that
needs to be forwarded to the PF for approval. This list is a 256-bit
bitmap. The code that sets up the bitmap falls apart on big-endian
architecture. __set_bit() does not work because it operates on long types
whereas the firmware interface is defined in u32 types, causing bits in
the wrong 32-bit word to be set.
Fix it by setting the proper bits on an array of u32.
Fixes: de68f5de56 ("bnxt_en: Fix bitmap declaration to work on 32-bit arches.")
Reported-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When changing channels from combined to rx/tx or vice versa, the code
uses the wrong "sh" parameter to determine if we are reserving rings
for shared or non-shared mode. It should be using the ethtool requested
"sh" parameter instead of the current "sh" parameter.
Fix it by passing the "sh" parameter to bnxt_reserve_rings(). For
ethtool, we will pass in the requested "sh" parameter.
Fixes: 391be5c273 ("bnxt_en: Implement new scheme to reserve tx rings.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
.ndo_get_stats64() may not be protected by RTNL and can race with
.ndo_stop() or other ethtool operations that can free the statistics
memory. Fix it by setting a new flag BNXT_STATE_READ_STATS and then
proceeding to read statistics memory only if the state is OPEN. The
close path that frees the memory clears the OPEN state and then waits
for the BNXT_STATE_READ_STATS to clear before proceeding to free the
statistics memory.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To handle netpoll properly, the driver must only handle TX packets
during NAPI. Handling RX events cause warnings and errors in
netpoll mode. The ndo_poll_controller() method should call
napi_schedule() directly so that a NAPI weight of zero will be used
during netpoll mode.
The bnxt_en driver supports 2 ring modes: combined, and separate rx/tx.
In separate rx/tx mode, the ndo_poll_controller() method will only
process the tx rings. In combined mode, the rx and tx completion
entries are mixed in the completion ring and we need to drop the rx
entries and recycle the rx buffers.
Add a function bnxt_force_rx_discard() to handle this in netpoll mode
when we see rx entries in combined ring mode.
Reported-by: Calvin Owens <calvinowens@fb.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we get a TPA_END completion to handle a completed LRO packet, it
is possible that hardware would indicate errors. The current code is
not checking for the error condition. Define the proper error bits and
the macro to check for this error and abort properly.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to bnxt to report bpf_prog ID during XDP_QUERY_PROG.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Acked-by: Alexei Starovoitov <ast@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to push the chain index down to the drivers, so they have the
information to which chain the rule belongs. For now, no driver supports
multichain offload, so only chain 0 is supported. This is needed to
prevent chain squashes during offload for now. Later this will be used
to implement multichain offload.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to write the doorbell if BQL has stopped the queue and
skb->xmit_more is set. Otherwise it is possible for the tx queue to
rot and cause tx timeout.
Fixes: 4d172f21ce ("bnxt_en: Implement xmit_more.")
Suggested-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the existing code, the local variable sh is hardcoded to true to
calculate default rings for shared ring configuration. It is better
to have the caller determine the value of sh.
Reported-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not write the TX doorbell if skb->xmit_more is set unless the TX
queue is full.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Older chips require the doorbells to be written twice, but newer chips
do not. Add a new common function bnxt_db_write() to write all
doorbells appropriately depending on the chip. Eliminating the extra
doorbell on newer chips has a significant performance improvement
on pktgen.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add additional chip definitions and macros for all supported chips.
Add a new macro BNXT_CHIP_P4_PLUS for the newer generation of chips and
use the macro to properly determine the features supported by these
newer chips.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When bnxt_en gets a PCI shutdown call, we need to have a new callback
to inform the RDMA driver to do proper shutdown and removal.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Deepak Khungar <deepak.khungar@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new short message format is used on the new BCM57454 VFs. Each
firmware message is a fixed 16-byte message sent using the standard
firmware communication channel. The short message has a DMA address
pointing to the legacy long firmware message.
Signed-off-by: Deepak Khungar <deepak.khungar@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise, all the host based DCBX settings from lldpad will fail if the
firmware DCBX agent is running.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current code, bnxt_dcb_init() is called too early before we
determine if the firmware DCBX agent is running or not. As a result,
we are not setting the DCB_CAP_DCBX_HOST and DCB_CAP_DCBX_LLD_MANAGED
flags properly to report to DCBNL.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the SPARC platform we need to use the DMA_ATTR_WEAK_ORDERING attribute
in our Rx path dma mapping in order to get the expected performance out
of the receive path. Adding it to the Tx path has little effect, so
that's not a part of this patch.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Reviewed-by: Tushar Dave <tushar.n.dave@oracle.com>
Reviewed-by: Tom Saeger <tom.saeger@oracle.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have the number of longs, but we need to calculate the number of
bytes required.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change restricts the PF in multi-host mode from setting any port
level PHY configuration. The settings are controlled by firmware in
Multi-Host mode.
Signed-off-by: Deepak Khungar <deepak.khungar@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the additional flag in bnxt_hwrm_func_qcfg() before allowing
DCBX to be done in host mode.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for 100G link speed reporting for Broadcom BCM57454
ASIC in ethtool command.
Signed-off-by: Deepak Khungar <deepak.khungar@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The .ndo_get_vf_config() is returning the wrong qos attribute. Fix
the code that checks and reports the qos and spoofchk attributes. The
BNXT_VF_QOS and BNXT_VF_LINK_UP flags should not be set by default
during init. time.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the driver gets the RoCE app priority set/delete call through DCBNL,
the driver will send the information to the firmware to set up the
priority VLAN tag for RDMA traffic.
[ New version using the common ETH_P_IBOE constant in if_ether.h ]
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly simple cases of overlapping changes (adding code nearby,
a function whose name changes, for example).
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code enables up to the maximum MSIX vectors in the PCIE
config space without considering the max completion rings available.
An MSIX vector is only useful when it has an associated completion
ring, so it is better to cap it.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No offload is performed on the XDP_TX ring so we can use the short TX
BDs. This has the effect of doubling the size of the XDP TX ring so
that it now matches the size of the rx ring by default.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is necessary to disable autoneg before enabling PHY loopback,
otherwise link won't come up.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mac loopback self test operates in polling mode. To support that,
we need to add functions to open and close the NIC half way. The half
open mode allows the rings to operate without IRQ and NAPI. We
use the XDP transmit function to send the loopback packet.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the basic infrastructure and only firmware tests initially.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add suspend/resume callbacks using the newer dev_pm_ops method.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And add functions to set and free magic packet filter.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add pci shutdown method to put device in the proper WoL and power state.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add code to driver probe function to check if the device is WoL capable
and if Magic packet WoL filter is currently set.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Features added include WoL and selftest.
Signed-off-by: Deepak Khungar <deepak.khungar@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These files all use functions declared in interrupt.h, but currently rely
on implicit inclusion of this file (via netns/xfrm.h).
That won't work anymore when the flow cache is removed so include that
header where needed.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In bnxt_free_rx_skbs(), which is called to free up all RX buffers during
shutdown, we need to unmap the page if we are running in XDP mode.
Fixes: c61fb99cae ("bnxt_en: Add RX page mode support.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sankar Patchineelam <sankar.patchineelam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Net device reset can fail when the h/w or f/w is in a bad state.
Subsequent netdevice open fails in bnxt_hwrm_stat_ctx_alloc().
The cleanup invokes bnxt_hwrm_resource_free() which inturn
calls bnxt_disable_int(). In this routine, the code segment
if (ring->fw_ring_id != INVALID_HW_RING_ID)
BNXT_CP_DB(cpr->cp_doorbell, cpr->cp_raw_cons);
results in NULL pointer dereference as cpr->cp_doorbell is not yet
initialized, and fw_ring_id is zero.
The fix is to initialize cpr fw_ring_id to INVALID_HW_RING_ID before
bnxt_init_chip() is invoked.
Signed-off-by: Sankar Patchineelam <sankar.patchineelam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The configurable priority to traffic class mapping and the user specified
queue ranges are used to configure the traffic class, overriding the
hardware defaults when the 'hw' option is set to 0. However, when the 'hw'
option is non-zero, the hardware QOS defaults are used.
This patch makes it so that we can pass the data the user provided to
ndo_setup_tc. This allows us to pull in the queue configuration if the
user requested it as well as any additional hardware offload type
requested by using a value other than 1 for the hw value.
Finally it also provides a means for the device driver to return the level
supported for the offload type via the qopt->hw value. Previously we were
just always assuming the value to be 1, in the future values beyond just 1
may be supported.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some situations, the firmware will return 0 for autoneg supported
speed. This may happen if the firmware detects no SFP module, for
example. The driver should ignore this so that we don't end up with
an invalid autoneg setting with nothing advertised. When SFP module
is inserted, we'll get the updated settings from firmware at that time.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set DCB_CAP_DCBX_HOST capability flag only if the firmware LLDP agent
is not running.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we call bnxt_reset_task() due to tx timeout, we should call
bnxt_ulp_stop() to inform the RDMA driver about the error and the
impending reset.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware call to do function reset is done too late. It is causing
the rings that have been reserved to be freed. In NPAR mode, this bug
is causing us to run out of rings.
Fixes: 391be5c273 ("bnxt_en: Implement new scheme to reserve tx rings.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use eth_hw_addr_random() to set a random MAC address in order to make
sure bp->dev->addr_assign_type will be properly set to NET_ADDR_RANDOM.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the bnxt_init_one() failure path, bar1 and bar2 are not
being unmapped. This commit fixes this issue. Reorganize the
code so that bnxt_init_one()'s failure path and bnxt_remove_one()
can call the same function to do the PCI cleanup.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If bnxt_hwrm_ring_free() is called during a failure path in bnxt_open(),
it is possible that the completion rings have not been allocated yet.
In that case, the completion doorbell has not been initialized, and
calling bnxt_disable_int() will crash. Fix it by checking that the
completion ring has been initialized before writing to the completion
ring doorbell.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are additional SoC devices that use the same device ID for
bridge and NIC devices. The bnxt driver should reject probe against
all bridge devices since it's meant to be used with only endpoint
devices.
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Deepak Khungar <deepak.khungar@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add proper puctuation to make the message more clear.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print FEC (Forward Error Correction) autoneg and encoding settings during
link up.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If it is a VF or an NPAR function, the firmware call to setup the PHY
will fail. Adding this check will prevent unnecessary firmware calls
to setup the PHY unless calling from the PF. This will also eliminate
many unnecessary warning messages when the call from a VF or NPAR fails.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If skb_flow_dissect_flow_keys() returns with the encapsulation flag
set, pass the information to the firmware to setup the NTUPLE filter
accordingly.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ae10ae740a ("bnxt_en: Add new hardware RFS mode.") has added
code to allow NTUPLE to be enabled on VFs. So we now remove the
BNXT_VF() check in rfs_capable() to allow NTUPLE on VFs.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With commit d1e7925e6d ("bnxt_en: Centralize logic to reserve rings."),
ring allocation for combined rings has become stricter. A combined
ring must now have an rx-tx ring pair. The pre-set max. for combined
rings should now be min(rx, tx).
Fixes: d1e7925e6d ("bnxt_en: Centralize logic to reserve rings.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the HWRM_NVM_INSTALL_UPDATE command fails with the error code
NVM_INSTALL_UPDATE_CMD_ERR_CODE_FRAG_ERR, retry the command with
a new flag to allow defragmentation. Since we are checking the
response for error code, we also need to take the mutex until
we finish reading the response.
Signed-off-by: Kshitij Soni <kshitij.soni@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new spec has NVRAM defragmentation support which will be used in
the next patch to improve ethtool flash operation.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add dedicated transmit function and transmit completion handler for
XDP. The XDP transmit logic and completion logic are different than
regular TX ring. The TX buffer is recycled back to the RX ring when
it completes.
v3: Improved the buffer recyling scheme for XDP_TX.
v2: Add trace_xdp_exception().
Add dma_sync.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Tested-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic ndo_xdp support to setup and query program, configure the NIC
to run in rx page mode, and support XDP_PASS, XDP_DROP, XDP_ABORTED
actions only.
v3: Pass modified offset and length to stack for XDP_PASS.
Remove Kconfig option.
v2: Added trace_xdp_exception()
Added dma_syncs.
Added XDP headroom support.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Tested-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XDP_TX requires a different function to handle completion. Add a
function pointer to handle tx completion logic. Regular TX rings
will be assigned the current bnxt_tx_int() for the ->tx_int()
function pointer.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add logic for an extra set of TX rings for XDP. If enabled, this
set of TX rings equals the number of RX rings and shares the same
IRQ as the RX ring set. A new field bp->tx_nr_rings_xdp is added
to keep track of these TX XDP rings. Adjust all other relevant functions
to handle bp->tx_nr_rings_xdp.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To support XDP_TX, we need to add a set of dedicated TX rings, each
associated with the NAPI of an RX ring. To assign XDP rings and regular
rings in a flexible way, we add a bp->tx_ring_map[] array to do the
remapping. The netdev txq index is stored in the new field txq_index
so that we can retrieve the netdev txq when handling TX completions.
In this patch, before we introduce XDP_TX, the mapping is 1:1.
v2: Fixed a bug in bnxt_tx_int().
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, bnxt_setup_tc() and bnxt_set_channels() have similar and
duplicated code to check and reserve rx and tx rings. Add a new
function bnxt_reserve_rings() to centralize the logic. This will
make it easier to add XDP_TX support which requires allocating a
new set of TX rings.
Also, the tx ring checking logic in bnxt_setup_msix() can be removed.
The rings have been reserved before hand.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current code, we have separate rx_event and agg_event parameters
to keep track of rx and aggregation events. Combine these events into
an u8 event mask with different bits defined for different events. This
way, it is easier to expand the logic to include XDP tx events.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This mode is to support XDP. In this mode, each rx ring is configured
with page sized buffers for linear placement of each packet. MTU will be
restricted to what the page sized buffers can support.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the global constants BNXT_RX_OFFSET and BNXT_RX_DMA_OFFSET to
device parameters. This will make it easier to support XDP with
headroom support which requires different RX buffer offsets.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When driver is running in XDP mode, rx buffers are DMA mapped as
DMA_BIDIRECTIONAL. Add a field so the code will map/unmap rx buffers
according to this field.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To support XDP_TX, we need the RX buffer's DMA address to transmit the
packet. Convert the DMA address field to a permanent field in
bnxt_sw_rx_bd.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor refactoring of bnxt_rx_skb() so that it can easily be replaced by
a new function that handles packets in a single page. Also, use a
function pointer bp->rx_skb_func() to switch to a new function when
we add the new mode in the next patch.
Add a new field data_ptr that points to the packet data in the
bnxt_sw_rx_bd structure. The original data field is changed to void
pointer so that it can either hold the kmalloc'ed data or a page
pointer.
The last parameter of bnxt_rx_skb() which was the length parameter is
changed to include the payload offset of the packet in the upper 16 bit.
The offset is needed to support the rx page mode and is not used in
this existing function.
v3: Added a new data_ptr parameter to bp->rx_skb_func(). The caller
has the option to modify the starting address of the packet. This
will be needed when XDP with headroom support is added.
v2: Changed the name of the last parameter to offset_and_len to make the
code more clear.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396
("net: gro: add a per device gro flush timer")
This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_get_port_module_status() calls bnxt_update_link() which expects
RTNL to be held. In bnxt_sp_task() that does not hold RTNL, we need to
call it with a prior call to bnxt_rtnl_lock_sp() and the call needs to
be moved to the end of bnxt_sp_task().
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_update_link() is called from multiple code paths. Most callers,
such as open, ethtool, already hold RTNL. Only the caller bnxt_sp_task()
does not. So it is a bug to take RTNL inside bnxt_update_link().
Fix it by removing the RTNL inside bnxt_update_link(). The function
now expects the caller to always hold RTNL.
In bnxt_sp_task(), call bnxt_rtnl_lock_sp() before calling
bnxt_update_link(). We also need to move the call to the end of
bnxt_sp_task() since it will be clearing the BNXT_STATE_IN_SP_TASK bit.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In bnxt_sp_task(), we set a bit BNXT_STATE_IN_SP_TASK so that bnxt_close()
will synchronize and wait for bnxt_sp_task() to finish. Some functions
in bnxt_sp_task() require us to clear BNXT_STATE_IN_SP_TASK and then
acquire rtnl_lock() to prevent race conditions.
There are some bugs related to this logic. This patch refactors the code
to have common bnxt_rtnl_lock_sp() and bnxt_rtnl_unlock_sp() to handle
the RTNL and the clearing/setting of the bit. Multiple functions will
need the same logic. We also need to move bnxt_reset() to the end of
bnxt_sp_task(). Functions that clear BNXT_STATE_IN_SP_TASK must be the
last functions to be called in bnxt_sp_task(). The common scheme will
handle the condition properly.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the TPA GRO code path, initialize the tcp_opt_len variable to 0 so
that it will be correct for packets without TCP timestamps. The bug
caused the SKB fields to be incorrectly set up for packets without
TCP timestamps, leading to these packets being rejected by the stack.
Reported-by: Andy Gospodarek <andrew.gospodarek@broadocm.com>
Acked-by: Andy Gospodarek <andrew.gospodarek@broadocm.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ulp_sriov_cfg callbacks when the number of VFs is changing. This
allows the RDMA driver to provision RDMA resources for the VFs.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add LED blinking code to support ethtool -p on the PF.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bdbd1eb59c ("bnxt_en: Handle no aggregation ring gracefully.")
introduced the BNXT_FLAG_NO_AGG_RINGS flag. For consistency,
bnxt_set_tpa_flags() should also clear TPA flags when there are no
aggregation rings.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC [M] drivers/net/ethernet/broadcom/bnxt/bnxt.o
drivers/net/ethernet/broadcom/bnxt/bnxt.c:4947:21: warning: ‘bnxt_get_max_func_rss_ctxs’ defined but not used [-Wunused-function]
static unsigned int bnxt_get_max_func_rss_ctxs(struct bnxt *bp)
^
CC [M] drivers/net/ethernet/broadcom/bnxt/bnxt.o
drivers/net/ethernet/broadcom/bnxt/bnxt.c:4956:21: warning: ‘bnxt_get_max_func_vnics’ defined but not used [-Wunused-function]
static unsigned int bnxt_get_max_func_vnics(struct bnxt *bp)
^
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In dev_get_stats() the statistic structure storage has already been
zeroed. Therefore network drivers do not need to call memset() again.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.
Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code assumes that we will always have at least 2 rx rings, 1
will be used as an aggregation ring for TPA and jumbo page placements.
However, it is possible, especially on a VF, that there is only 1 rx
ring available. In this scenario, the current code will fail to initialize.
To handle it, we need to properly set up only 1 ring without aggregation.
Set a new flag BNXT_FLAG_NO_AGG_RINGS for this condition and add logic to
set up the chip to place RX data linearly into a single buffer per packet.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the added support for the bnxt_re RDMA driver, both drivers can be
allocating completion rings in any order. The firmware does not know
which completion ring should be receiving async events. Add an
extra step to tell firmware the completion ring number for receiving
async events after bnxt_en allocates the completion rings.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to properly support TX rate limiting in SRIOV VF functions or
NPAR functions, firmware needs better control over tx ring allocations.
The new scheme requires the driver to reserve the number of tx rings
and to query to see if the requested number of tx rings is reserved.
The driver will use the new scheme when the firmware interface spec is
1.6.1 or newer.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Accept ipv6 flows in .ndo_rx_flow_steer() and support ETHTOOL_GRXCLSRULE
ipv6 flows.
Signed-off-by: Michael Chan <michael.chan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Assign additional vnics to VFs whenever possible so that NTUPLE can be
supported on the VFs.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing hardware RFS mode uses one hardware RSS context block
per ring just to calculate the RSS hash. This is very wasteful and
prevents VF functions from using it. The new hardware mode shares
the same hardware RSS context for RSS placement and RFS steering.
This allows VFs to enable RFS.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add function bnxt_rfs_supported() that determines if the chip supports
RFS. Refactor the existing function bnxt_rfs_capable() that determines
if run-time conditions support RFS.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
