In order to prepare for CONFIG_VIRT_CPU_ACCOUNTING_NATIVE=y to delay
cputime accounting to the tick, provide finegrained accumulators to
powerpc in order to store the cputime until flushing.
While at it, normalize the name of several fields according to common
cputime naming.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Wanpeng Li <wanpeng.li@hotmail.com>
Link: http://lkml.kernel.org/r/1483636310-6557-6-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On context switch with powerpc32, the cputime is accumulated in the
thread_info struct. So the switching-in task must move forward its
start time snapshot to the current time in order to later compute the
delta spent in system mode.
This is what we do for the normal cputime by initializing the starttime
field to the value of the previous task's starttime which got freshly
updated.
But we are missing the update of the scaled cputime start time. As a
result we may be accounting too much scaled cputime later.
Fix this by initializing the scaled cputime the same way we do for
normal cputime.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Wanpeng Li <wanpeng.li@hotmail.com>
Link: http://lkml.kernel.org/r/1483636310-6557-2-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
I am getting the following warning when I build kernel 4.9-git on my
PowerBook G4 with a 32-bit PPC processor:
AS arch/powerpc/kernel/misc_32.o
arch/powerpc/kernel/misc_32.S:299:7: warning: "CONFIG_FSL_BOOKE" is not defined [-Wundef]
This problem is evident after commit 989cea5c14 ("kbuild: prevent
lib-ksyms.o rebuilds"); however, this change in kbuild only exposes an
error that has been in the code since 2005 when this source file was
created. That was with commit 9994a33865 ("powerpc: Introduce
entry_{32,64}.S, misc_{32,64}.S, systbl.S").
The offending line does not make a lot of sense. This error does not
seem to cause any errors in the executable, thus I am not recommending
that it be applied to any stable versions.
Thanks to Nicholas Piggin for suggesting this solution.
Fixes: 9994a33865 ("powerpc: Introduce entry_{32,64}.S, misc_{32,64}.S, systbl.S")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no point in having an extra type for extra confusion. u64 is
unambiguous.
Conversion was done with the following coccinelle script:
@rem@
@@
-typedef u64 cycle_t;
@fix@
typedef cycle_t;
@@
-cycle_t
+u64
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The IMA kexec buffer allows the currently running kernel to pass the
measurement list via a kexec segment to the kernel that will be kexec'd.
This is the architecture-specific part of setting up the IMA kexec
buffer for the next kernel. It will be used in the next patch.
Link: http://lkml.kernel.org/r/1480554346-29071-6-git-send-email-zohar@linux.vnet.ibm.com
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Andreas Steffen <andreas.steffen@strongswan.org>
Cc: Dmitry Kasatkin <dmitry.kasatkin@gmail.com>
Cc: Josh Sklar <sklar@linux.vnet.ibm.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "ima: carry the measurement list across kexec", v8.
The TPM PCRs are only reset on a hard reboot. In order to validate a
TPM's quote after a soft reboot (eg. kexec -e), the IMA measurement
list of the running kernel must be saved and then restored on the
subsequent boot, possibly of a different architecture.
The existing securityfs binary_runtime_measurements file conveniently
provides a serialized format of the IMA measurement list. This patch
set serializes the measurement list in this format and restores it.
Up to now, the binary_runtime_measurements was defined as architecture
native format. The assumption being that userspace could and would
handle any architecture conversions. With the ability of carrying the
measurement list across kexec, possibly from one architecture to a
different one, the per boot architecture information is lost and with it
the ability of recalculating the template digest hash. To resolve this
problem, without breaking the existing ABI, this patch set introduces
the boot command line option "ima_canonical_fmt", which is arbitrarily
defined as little endian.
The need for this boot command line option will be limited to the
existing version 1 format of the binary_runtime_measurements.
Subsequent formats will be defined as canonical format (eg. TPM 2.0
support for larger digests).
A simplified method of Thiago Bauermann's "kexec buffer handover" patch
series for carrying the IMA measurement list across kexec is included in
this patch set. The simplified method requires all file measurements be
taken prior to executing the kexec load, as subsequent measurements will
not be carried across the kexec and restored.
This patch (of 10):
The IMA kexec buffer allows the currently running kernel to pass the
measurement list via a kexec segment to the kernel that will be kexec'd.
The second kernel can check whether the previous kernel sent the buffer
and retrieve it.
This is the architecture-specific part which enables IMA to receive the
measurement list passed by the previous kernel. It will be used in the
next patch.
The change in machine_kexec_64.c is to factor out the logic of removing
an FDT memory reservation so that it can be used by remove_ima_buffer.
Link: http://lkml.kernel.org/r/1480554346-29071-2-git-send-email-zohar@linux.vnet.ibm.com
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Andreas Steffen <andreas.steffen@strongswan.org>
Cc: Dmitry Kasatkin <dmitry.kasatkin@gmail.com>
Cc: Josh Sklar <sklar@linux.vnet.ibm.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Highlights include:
- Support for the kexec_file_load() syscall, which is a prereq for secure and
trusted boot.
- Prevent kernel execution of userspace on P9 Radix (similar to SMEP/PXN).
- Sort the exception tables at build time, to save time at boot, and store
them as relative offsets to save space in the kernel image & memory.
- Allow building the kernel with thin archives, which should allow us to build
an allyesconfig once some other fixes land.
- Build fixes to allow us to correctly rebuild when changing the kernel endian
from big to little or vice versa.
- Plumbing so that we can avoid doing a full mm TLB flush on P9 Radix.
- Initial stack protector support (-fstack-protector).
- Support for dumping the radix (aka. Linux) and hash page tables via debugfs.
- Fix an oops in cxl coredump generation when cxl_get_fd() is used.
- Freescale updates from Scott: "Highlights include 8xx hugepage support,
qbman fixes/cleanup, device tree updates, and some misc cleanup."
- Many and varied fixes and minor enhancements as always.
Thanks to:
Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V, Anshuman Khandual,
Anton Blanchard, Balbir Singh, Bartlomiej Zolnierkiewicz, Christophe Jaillet,
Christophe Leroy, Denis Kirjanov, Elimar Riesebieter, Frederic Barrat,
Gautham R. Shenoy, Geliang Tang, Geoff Levand, Jack Miller, Johan Hovold,
Lars-Peter Clausen, Libin, Madhavan Srinivasan, Michael Neuling, Nathan
Fontenot, Naveen N. Rao, Nicholas Piggin, Pan Xinhui, Peter Senna Tschudin,
Rashmica Gupta, Rui Teng, Russell Currey, Scott Wood, Simon Guo, Suraj
Jitindar Singh, Thiago Jung Bauermann, Tobias Klauser, Vaibhav Jain.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xOzf
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights include:
- Support for the kexec_file_load() syscall, which is a prereq for
secure and trusted boot.
- Prevent kernel execution of userspace on P9 Radix (similar to
SMEP/PXN).
- Sort the exception tables at build time, to save time at boot, and
store them as relative offsets to save space in the kernel image &
memory.
- Allow building the kernel with thin archives, which should allow us
to build an allyesconfig once some other fixes land.
- Build fixes to allow us to correctly rebuild when changing the
kernel endian from big to little or vice versa.
- Plumbing so that we can avoid doing a full mm TLB flush on P9
Radix.
- Initial stack protector support (-fstack-protector).
- Support for dumping the radix (aka. Linux) and hash page tables via
debugfs.
- Fix an oops in cxl coredump generation when cxl_get_fd() is used.
- Freescale updates from Scott: "Highlights include 8xx hugepage
support, qbman fixes/cleanup, device tree updates, and some misc
cleanup."
- Many and varied fixes and minor enhancements as always.
Thanks to:
Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V, Anshuman
Khandual, Anton Blanchard, Balbir Singh, Bartlomiej Zolnierkiewicz,
Christophe Jaillet, Christophe Leroy, Denis Kirjanov, Elimar
Riesebieter, Frederic Barrat, Gautham R. Shenoy, Geliang Tang, Geoff
Levand, Jack Miller, Johan Hovold, Lars-Peter Clausen, Libin,
Madhavan Srinivasan, Michael Neuling, Nathan Fontenot, Naveen N.
Rao, Nicholas Piggin, Pan Xinhui, Peter Senna Tschudin, Rashmica
Gupta, Rui Teng, Russell Currey, Scott Wood, Simon Guo, Suraj
Jitindar Singh, Thiago Jung Bauermann, Tobias Klauser, Vaibhav Jain"
[ And thanks to Michael, who took time off from a new baby to get this
pull request done. - Linus ]
* tag 'powerpc-4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (174 commits)
powerpc/fsl/dts: add FMan node for t1042d4rdb
powerpc/fsl/dts: add sg_2500_aqr105_phy4 alias on t1024rdb
powerpc/fsl/dts: add QMan and BMan nodes on t1024
powerpc/fsl/dts: add QMan and BMan nodes on t1023
soc/fsl/qman: test: use DEFINE_SPINLOCK()
powerpc/fsl-lbc: use DEFINE_SPINLOCK()
powerpc/8xx: Implement support of hugepages
powerpc: get hugetlbpage handling more generic
powerpc: port 64 bits pgtable_cache to 32 bits
powerpc/boot: Request no dynamic linker for boot wrapper
soc/fsl/bman: Use resource_size instead of computation
soc/fsl/qe: use builtin_platform_driver
powerpc/fsl_pmc: use builtin_platform_driver
powerpc/83xx/suspend: use builtin_platform_driver
powerpc/ftrace: Fix the comments for ftrace_modify_code
powerpc/perf: macros for power9 format encoding
powerpc/perf: power9 raw event format encoding
powerpc/perf: update attribute_group data structure
powerpc/perf: factor out the event format field
powerpc/mm/iommu, vfio/spapr: Put pages on VFIO container shutdown
...
Merge more updates from Andrew Morton:
- a few misc things
- kexec updates
- DMA-mapping updates to better support networking DMA operations
- IPC updates
- various MM changes to improve DAX fault handling
- lots of radix-tree changes, mainly to the test suite. All leading up
to reimplementing the IDA/IDR code to be a wrapper layer over the
radix-tree. However the final trigger-pulling patch is held off for
4.11.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (114 commits)
radix tree test suite: delete unused rcupdate.c
radix tree test suite: add new tag check
radix-tree: ensure counts are initialised
radix tree test suite: cache recently freed objects
radix tree test suite: add some more functionality
idr: reduce the number of bits per level from 8 to 6
rxrpc: abstract away knowledge of IDR internals
tpm: use idr_find(), not idr_find_slowpath()
idr: add ida_is_empty
radix tree test suite: check multiorder iteration
radix-tree: fix replacement for multiorder entries
radix-tree: add radix_tree_split_preload()
radix-tree: add radix_tree_split
radix-tree: add radix_tree_join
radix-tree: delete radix_tree_range_tag_if_tagged()
radix-tree: delete radix_tree_locate_item()
radix-tree: improve multiorder iterators
btrfs: fix race in btrfs_free_dummy_fs_info()
radix-tree: improve dump output
radix-tree: make radix_tree_find_next_bit more useful
...
This change allows us to pass DMA_ATTR_SKIP_CPU_SYNC which allows us to
avoid invoking cache line invalidation if the driver will just handle it
via a sync_for_cpu or sync_for_device call.
Link: http://lkml.kernel.org/r/20161110113534.76501.86492.stgit@ahduyck-blue-test.jf.intel.com
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull namespace updates from Eric Biederman:
"After a lot of discussion and work we have finally reachanged a basic
understanding of what is necessary to make unprivileged mounts safe in
the presence of EVM and IMA xattrs which the last commit in this
series reflects. While technically it is a revert the comments it adds
are important for people not getting confused in the future. Clearing
up that confusion allows us to seriously work on unprivileged mounts
of fuse in the next development cycle.
The rest of the fixes in this set are in the intersection of user
namespaces, ptrace, and exec. I started with the first fix which
started a feedback cycle of finding additional issues during review
and fixing them. Culiminating in a fix for a bug that has been present
since at least Linux v1.0.
Potentially these fixes were candidates for being merged during the rc
cycle, and are certainly backport candidates but enough little things
turned up during review and testing that I decided they should be
handled as part of the normal development process just to be certain
there were not any great surprises when it came time to backport some
of these fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
Revert "evm: Translate user/group ids relative to s_user_ns when computing HMAC"
exec: Ensure mm->user_ns contains the execed files
ptrace: Don't allow accessing an undumpable mm
ptrace: Capture the ptracer's creds not PT_PTRACE_CAP
mm: Add a user_ns owner to mm_struct and fix ptrace permission checks
x86: userspace can now hide nested VMX features from guests; nested
VMX can now run Hyper-V in a guest; support for AVX512_4VNNIW and
AVX512_FMAPS in KVM; infrastructure support for virtual Intel GPUs.
PPC: support for KVM guests on POWER9; improved support for interrupt
polling; optimizations and cleanups.
s390: two small optimizations, more stuff is in flight and will be
in 4.11.
ARM: support for the GICv3 ITS on 32bit platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQExBAABCAAbBQJYTkP0FBxwYm9uemluaUByZWRoYXQuY29tAAoJEL/70l94x66D
lZIH/iT1n9OQXcuTpYYnQhuCenzI3GZZOIMTbCvK2i5bo0FIJKxVn0EiAAqZSXvO
nO185FqjOgLuJ1AD1kJuxzye5suuQp4HIPWWgNHcexLuy43WXWKZe0IQlJ4zM2Xf
u31HakpFmVDD+Cd1qN3yDXtDrRQ79/xQn2kw7CWb8olp+pVqwbceN3IVie9QYU+3
gCz0qU6As0aQIwq2PyalOe03sO10PZlm4XhsoXgWPG7P18BMRhNLTDqhLhu7A/ry
qElVMANT7LSNLzlwNdpzdK8rVuKxETwjlc1UP8vSuhrwad4zM2JJ1Exk26nC2NaG
D0j4tRSyGFIdx6lukZm7HmiSHZ0=
=mkoB
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"Small release, the most interesting stuff is x86 nested virt
improvements.
x86:
- userspace can now hide nested VMX features from guests
- nested VMX can now run Hyper-V in a guest
- support for AVX512_4VNNIW and AVX512_FMAPS in KVM
- infrastructure support for virtual Intel GPUs.
PPC:
- support for KVM guests on POWER9
- improved support for interrupt polling
- optimizations and cleanups.
s390:
- two small optimizations, more stuff is in flight and will be in
4.11.
ARM:
- support for the GICv3 ITS on 32bit platforms"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (94 commits)
arm64: KVM: pmu: Reset PMSELR_EL0.SEL to a sane value before entering the guest
KVM: arm/arm64: timer: Check for properly initialized timer on init
KVM: arm/arm64: vgic-v2: Limit ITARGETSR bits to number of VCPUs
KVM: x86: Handle the kthread worker using the new API
KVM: nVMX: invvpid handling improvements
KVM: nVMX: check host CR3 on vmentry and vmexit
KVM: nVMX: introduce nested_vmx_load_cr3 and call it on vmentry
KVM: nVMX: propagate errors from prepare_vmcs02
KVM: nVMX: fix CR3 load if L2 uses PAE paging and EPT
KVM: nVMX: load GUEST_EFER after GUEST_CR0 during emulated VM-entry
KVM: nVMX: generate MSR_IA32_CR{0,4}_FIXED1 from guest CPUID
KVM: nVMX: fix checks on CR{0,4} during virtual VMX operation
KVM: nVMX: support restore of VMX capability MSRs
KVM: nVMX: generate non-true VMX MSRs based on true versions
KVM: x86: Do not clear RFLAGS.TF when a singlestep trap occurs.
KVM: x86: Add kvm_skip_emulated_instruction and use it.
KVM: VMX: Move skip_emulated_instruction out of nested_vmx_check_vmcs12
KVM: VMX: Reorder some skip_emulated_instruction calls
KVM: x86: Add a return value to kvm_emulate_cpuid
KVM: PPC: Book3S: Move prototypes for KVM functions into kvm_ppc.h
...
Pull smp hotplug updates from Thomas Gleixner:
"This is the final round of converting the notifier mess to the state
machine. The removal of the notifiers and the related infrastructure
will happen around rc1, as there are conversions outstanding in other
trees.
The whole exercise removed about 2000 lines of code in total and in
course of the conversion several dozen bugs got fixed. The new
mechanism allows to test almost every hotplug step standalone, so
usage sites can exercise all transitions extensively.
There is more room for improvement, like integrating all the
pointlessly different architecture mechanisms of synchronizing,
setting cpus online etc into the core code"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (60 commits)
tracing/rb: Init the CPU mask on allocation
soc/fsl/qbman: Convert to hotplug state machine
soc/fsl/qbman: Convert to hotplug state machine
zram: Convert to hotplug state machine
KVM/PPC/Book3S HV: Convert to hotplug state machine
arm64/cpuinfo: Convert to hotplug state machine
arm64/cpuinfo: Make hotplug notifier symmetric
mm/compaction: Convert to hotplug state machine
iommu/vt-d: Convert to hotplug state machine
mm/zswap: Convert pool to hotplug state machine
mm/zswap: Convert dst-mem to hotplug state machine
mm/zsmalloc: Convert to hotplug state machine
mm/vmstat: Convert to hotplug state machine
mm/vmstat: Avoid on each online CPU loops
mm/vmstat: Drop get_online_cpus() from init_cpu_node_state/vmstat_cpu_dead()
tracing/rb: Convert to hotplug state machine
oprofile/nmi timer: Convert to hotplug state machine
net/iucv: Use explicit clean up labels in iucv_init()
x86/pci/amd-bus: Convert to hotplug state machine
x86/oprofile/nmi: Convert to hotplug state machine
...
8xx uses a two level page table with two different linux page size
support (4k and 16k). 8xx also support two different hugepage sizes
512k and 8M. In order to support them on linux we define two different
page table layout.
The size of pages is in the PGD entry, using PS field (bits 28-29):
00 : Small pages (4k or 16k)
01 : 512k pages
10 : reserved
11 : 8M pages
For 512K hugepage size a pgd entry have the below format
[<hugepte address >0101] . The hugepte table allocated will contain 8
entries pointing to 512K huge pte in 4k pages mode and 64 entries in
16k pages mode.
For 8M in 16k mode, a pgd entry have the below format
[<hugepte address >1101] . The hugepte table allocated will contain 8
entries pointing to 8M huge pte.
For 8M in 4k mode, multiple pgd entries point to the same hugepte
address and pgd entry will have the below format
[<hugepte address>1101]. The hugepte table allocated will only have one
entry.
For the time being, we do not support CPU15 ERRATA when HUGETLB is
selected
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> (v3, for the generic bits)
Signed-off-by: Scott Wood <oss@buserror.net>
Four fixes, the first for code we merged this cycle and three that are also
going to stable:
- On 64-bit Book3E we were not placing the .text section where we said we would
in the asm.
- We broke building the boot wrapper on some 32-bit toolchains.
- Lazy icache flushing was broken on pre-POWER5 machines.
- One of the error paths in our EEH code would lead to a deadlock.
Thanks to:
Andrew Donnellan, Ben Hutchings, Benjamin Herrenschmidt, Nicholas Piggin.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6IL4
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.9-7' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Four fixes, the first for code we merged this cycle and three that are
also going to stable:
- On 64-bit Book3E we were not placing the .text section where we
said we would in the asm.
- We broke building the boot wrapper on some 32-bit toolchains.
- Lazy icache flushing was broken on pre-POWER5 machines.
- One of the error paths in our EEH code would lead to a deadlock.
Thanks to: Andrew Donnellan, Ben Hutchings, Benjamin Herrenschmidt,
Nicholas Piggin"
* tag 'powerpc-4.9-7' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64: Fix placement of .text to be immediately following .head.text
powerpc/eeh: Fix deadlock when PE frozen state can't be cleared
powerpc/mm: Fix lazy icache flush on pre-POWER5
powerpc/boot: Fix build failure in 32-bit boot wrapper
There is no need to worry about module and __init text disappearing
case, because that ftrace has a module notifier that is called when a
module is being unloaded and before the text goes away and this code
grabs the ftrace_lock mutex and removes the module functions from the
ftrace list, such that it will no longer do any modifications to that
module's text, the update to make functions be traced or not is done
under the ftrace_lock mutex as well. And by now, __init section codes
should not been modified by ftrace, because it is black listed in
recordmcount.c and ignored by ftrace.
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Li Bin <huawei.libin@huawei.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We are going to get rid of @current references in mmu_context_boos3s64.c
and cache mm_struct in the VFIO container. Since mm_context_t does not
have reference counting, we will be using mm_struct which does have
the reference counter.
This changes mm_iommu_init/mm_iommu_cleanup to receive mm_struct rather
than mm_context_t (which is embedded into mm).
This should not cause any behavioral change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The current facility_strings[] are correct when the trap address is
0xf80 (hypervisor facility unavailable). When the trap address is
0xf60 (facility unavailable) IC (Interruption Cause) a.k.a status in the
code is undefined for values 0 and 1.
Add a check to prevent printing the (misleading) facility name for IC 0
and 1 when we came in via 0xf60. In all cases, print the actual IC
value, to avoid any confusion.
This hasn't been seen on real hardware, on only qemu which was
misreporting an exception.
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
[mpe: Fix indentation, combine printks(), massage change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Do not introduce any additional alignment. Placement of text section
will be set by fixed section macros. Without this, output section
alignment defaults to 4096, which makes BookE text section start at
0x1000 when it is expected to start at 0x100.
This was introduced by commit 57f266497d ("powerpc: Use gas sections
for arranging exception vectors") and was caught with the scripted head
section checker (not yet merged).
Fixes: 57f266497d ("powerpc: Use gas sections for arranging exception vectors")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In eeh_reset_device(), we take the pci_rescan_remove_lock immediately after
after we call eeh_reset_pe() to reset the PCI controller. We then call
eeh_clear_pe_frozen_state(), which can return an error. In this case, we
bail out of eeh_reset_device() without calling pci_unlock_rescan_remove().
Add a call to pci_unlock_rescan_remove() in the eeh_clear_pe_frozen_state()
error path so that we don't cause a deadlock later on.
Reported-by: Pradipta Ghosh <pradghos@in.ibm.com>
Fixes: 7895470063 ("powerpc/eeh: Avoid I/O access during PE reset")
Cc: stable@vger.kernel.org # v3.16+
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that we've defined structures to describe each of the client
architecture vectors, we can use those to construct the value we pass to
firmware.
This avoids the tricks we previously played with the W() macro, allows
us to properly endian annotate fields, and should help to avoid bugs
introduced by failing to have the correct number of zero pad bytes
between fields.
It also means we can avoid hard coding IBM_ARCH_VEC_NRCORES_OFFSET in
order to update the max_cpus value and instead just set it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The "client architecture vectors" are a series of structures we pass to
firmware to define various things, such as what processors we support
and many other options.
Each structure is entirely different so we have to define a different
struct for each one, but that's OK.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This purgatory implementation is based on the versions from kexec-tools
and kexec-lite, with additional changes.
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds the support code needed for implementing
kexec_file_load() on powerpc.
This consists of functions to load the ELF kernel, either big or little
endian, and setup the purgatory enviroment which switches from the first
kernel to the second kernel.
None of this code is built yet, as it depends on CONFIG_KEXEC_FILE which
we have not yet defined. Although we could define CONFIG_KEXEC_FILE in
this patch, we'd then have a window in history where the kconfig symbol
is present but the syscall is not, which would be awkward.
Signed-off-by: Josh Sklar <sklar@linux.vnet.ibm.com>
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 2965faa5e0 ("kexec: split kexec_load syscall from kexec core
code") introduced CONFIG_KEXEC_CORE so that CONFIG_KEXEC means whether
the kexec_load system call should be compiled-in and CONFIG_KEXEC_FILE
means whether the kexec_file_load system call should be compiled-in.
These options can be set independently from each other.
Since until now powerpc only supported kexec_load, CONFIG_KEXEC and
CONFIG_KEXEC_CORE were synonyms. That is not the case anymore, so we
need to make a distinction. Almost all places where CONFIG_KEXEC was
being used should be using CONFIG_KEXEC_CORE instead, since
kexec_file_load also needs that code compiled in.
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This converts one that was missed by b1576fec7f ("powerpc: No need
to use dot symbols when branching to a function").
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
From 80f23935ca ("powerpc: Convert cmp to cmpd in idle enter sequence"):
PowerPC's "cmp" instruction has four operands. Normally people write
"cmpw" or "cmpd" for the second cmp operand 0 or 1. But, frequently
people forget, and write "cmp" with just three operands.
With older binutils this is silently accepted as if this was "cmpw",
while often "cmpd" is wanted. With newer binutils GAS will complain
about this for 64-bit code. For 32-bit code it still silently assumes
"cmpw" is what is meant.
In this case, cmpwi is called for, so this is just a build fix for
new toolchains.
Cc: stable@vger.kernel.org # v3.0+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fixes marked for stable:
- Set missing wakeup bit in LPCR on POWER9 (Benjamin Herrenschmidt)
- Fix the early OPAL console wrappers (Oliver O'Halloran)
- Fixup kernel read only mapping (Aneesh Kumar K.V)
Fixes for code merged this cycle:
- Fix missing CRCs, add more asm-prototypes.h declarations (Nicholas Piggin)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=75sc
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.9-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Fixes marked for stable:
- Set missing wakeup bit in LPCR on POWER9
- Fix the early OPAL console wrappers
- Fixup kernel read only mapping
Fixes for code merged this cycle:
- Fix missing CRCs, add more asm-prototypes.h declarations"
* tag 'powerpc-4.9-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mm: Fixup kernel read only mapping
powerpc/boot: Fix the early OPAL console wrappers
powerpc: Fix missing CRCs, add more asm-prototypes.h declarations
powerpc: Set missing wakeup bit in LPCR on POWER9
Ensure that PSSCR is set to a safe value corresponding to no
state-loss each time a POWER9 CPU comes online.
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Acked-By: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use builtin_platform_driver() helper to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER9 adds new capabilities to the tlbie (TLB invalidate entry)
and tlbiel (local tlbie) instructions. Both instructions get a
set of new parameters (RIC, PRS and R) which appear as bits in the
instruction word. The tlbiel instruction now has a second register
operand, which contains a PID and/or LPID value if needed, and
should otherwise contain 0.
This adapts KVM-HV's usage of tlbie and tlbiel to work on POWER9
as well as older processors. Since we only handle HPT guests so
far, we need RIC=0 PRS=0 R=0, which ends up with the same instruction
word as on previous processors, so we don't need to conditionally
execute different instructions depending on the processor.
The local flush on first entry to a guest in book3s_hv_rmhandlers.S
is a loop which depends on the number of TLB sets. Rather than
using feature sections to set the number of iterations based on
which CPU we're on, we now work out this number at VM creation time
and store it in the kvm_arch struct. That will make it possible to
get the number from the device tree in future, which will help with
compatibility with future processors.
Since mmu_partition_table_set_entry() does a global flush of the
whole LPID, we don't need to do the TLB flush on first entry to the
guest on each processor. Therefore we don't set all bits in the
tlb_need_flush bitmap on VM startup on POWER9.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds code to handle two new guest-accessible special-purpose
registers on POWER9: TIDR (thread ID register) and PSSCR (processor
stop status and control register). They are context-switched
between host and guest, and the guest values can be read and set
via the one_reg interface.
The PSSCR contains some fields which are guest-accessible and some
which are only accessible in hypervisor mode. We only allow the
guest-accessible fields to be read or set by userspace.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This merges in the ppc-kvm topic branch to get changes to
arch/powerpc code that are necessary for adding POWER9 KVM support.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Partially copied from commit df0698be14 ("ARM: stack protector:
change the canary value per task")
A new random value for the canary is stored in the task struct whenever
a new task is forked. This is meant to allow for different canary values
per task. On powerpc, GCC expects the canary value to be found in a global
variable called __stack_chk_guard. So this variable has to be updated
with the value stored in the task struct whenever a task switch occurs.
Because the variable GCC expects is global, this cannot work on SMP
unfortunately. So, on SMP, the same initial canary value is kept
throughout, making this feature a bit less effective although it is still
useful.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Partialy copied from commit c743f38013 ("ARM: initial stack protector
(-fstack-protector) support")
This is the very basic stuff without the changing canary upon
task switch yet. Just the Kconfig option and a constant canary
value initialized at boot time.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Invoke the kprobe handlers directly rather than through notify_die(), to
reduce path taken for handling kprobes. Similar to commit 6f6343f53d
("kprobes/x86: Call exception handlers directly from do_int3/do_debug").
While at it, rename post_kprobe_handler() to kprobe_post_handler() for
more uniform naming.
Reported-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Define and set the POWER9 HFSCR doorbell bit so that guests can use
msgsndp.
ISA 3.0 calls this MSGP, so name it accordingly in the code.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Install the callbacks via the state machine and let the core invoke
the callbacks on the already online CPUs.
The previous convention of keeping the files around until the CPU is dead
has not been preserved as there is no point to keep them available when the
cpu is going down. This makes the hotplug call symmetric.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: rt@linuxtronix.de
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Link: http://lkml.kernel.org/r/20161117183541.8588-17-bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
It is the reasonable expectation that if an executable file is not
readable there will be no way for a user without special privileges to
read the file. This is enforced in ptrace_attach but if ptrace
is already attached before exec there is no enforcement for read-only
executables.
As the only way to read such an mm is through access_process_vm
spin a variant called ptrace_access_vm that will fail if the
target process is not being ptraced by the current process, or
the current process did not have sufficient privileges when ptracing
began to read the target processes mm.
In the ptrace implementations replace access_process_vm by
ptrace_access_vm. There remain several ptrace sites that still use
access_process_vm as they are reading the target executables
instructions (for kernel consumption) or register stacks. As such it
does not appear necessary to add a permission check to those calls.
This bug has always existed in Linux.
Fixes: v1.0
Cc: stable@vger.kernel.org
Reported-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
There is a new bit, LPCR_PECE_HVEE (Hypervisor Virtualization Exit
Enable), which controls wakeup from STOP states on Hypervisor
Virtualization Interrupts (which happen to also be all external
interrupts in host or bare metal mode).
It needs to be set or we will miss wakeups.
Fixes: 9baaef0a22 ("powerpc/irq: Add support for HV virtualization interrupts")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[mpe: Rename it to HVEE to match the name in the ISA]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
eeh_pe_reset and eeh_reset_pe are two different functions in the same
file which do mostly the same thing. Not only is this confusing, but
potentially causes disrepancies in functionality, notably eeh_reset_pe
as it does not check return values for failure.
Refactor this into the following:
- eeh_pe_reset(): stays as is, performs a single operation, exported
- eeh_pe_reset_full(): new, full reset process that calls eeh_pe_reset()
- eeh_reset_pe(): removed and replaced by eeh_pe_reset_full()
- eeh_reset_pe_once(): removed
Signed-off-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PHB, PE (and by association MVE) numbers are printed as a mix of decimal
and hexadecimal throughout the kernel. This can be misleading, so make
them all hexadecimal.
Standardising on hex instead of dec because:
- PHB numbers are presented in hex in sysfs/debugfs (and lspci, etc)
- PE numbers are presented as hex in sysfs and parsed in hex in debugfs
The only place I think this could cause confusing are the messages during
boot, i.e.
pci 000a:01 : [PE# 000] Secondary bus 1 associated with PE#0
which can be a quick way to check PE numbers. pe_level_printk() will
only print two characters instead of three, so the above would be
pci 000a:01 : [PE# 00] Secondary bus 1 associated with PE#0
which gives a hint it's in hex.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When switching from/to a guest that has a transaction in progress,
we need to save/restore the checkpointed register state. Although
XER is part of the CPU state that gets checkpointed, the code that
does this saving and restoring doesn't save/restore XER.
This fixes it by saving and restoring the XER. To allow userspace
to read/write the checkpointed XER value, we also add a new ONE_REG
specifier.
The visible effect of this bug is that the guest may see its XER
value being corrupted when it uses transactions.
Fixes: e4e3812150 ("KVM: PPC: Book3S HV: Add transactional memory support")
Fixes: 0a8eccefcb ("KVM: PPC: Book3S HV: Add missing code for transaction reclaim on guest exit")
Cc: stable@vger.kernel.org # v3.15+
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Fixes marked for stable:
- Fix system reset interrupt winkle wakeups (Nicholas Piggin)
- Fix setting of AIL in hypervisor mode (Benjamin Herrenschmidt)
Fixes for code merged this cycle:
- Fix exception vector build with 2.23 era binutils (Hugh Dickins)
- Fix missing update of HID register on secondary CPUs (Aneesh Kumar K.V)
Other:
- Fix missing pr_cont()s in show_stack() (Michael Ellerman)
- Fix missing pr_cont()s in print_msr_bits() et. al. (Michael Ellerman)
- Fix missing pr_cont()s in show_regs() (Michael Ellerman)
- Fix missing pr_cont()s in instruction dump (Andrew Donnellan)
- Invalidate ERAT on tlbiel for POWER9 DD1 (Michael Neuling)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=+6XC
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.9-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Fixes marked for stable:
- fix system reset interrupt winkle wakeups
- fix setting of AIL in hypervisor mode
Fixes for code merged this cycle:
- fix exception vector build with 2.23 era binutils
- fix missing update of HID register on secondary CPUs
Other:
- fix missing pr_cont()s
- invalidate ERAT on tlbiel for POWER9 DD1"
* tag 'powerpc-4.9-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mm: Fix missing update of HID register on secondary CPUs
powerpc/mm/radix: Invalidate ERAT on tlbiel for POWER9 DD1
powerpc/64: Fix setting of AIL in hypervisor mode
powerpc/oops: Fix missing pr_cont()s in instruction dump
powerpc/oops: Fix missing pr_cont()s in show_regs()
powerpc/oops: Fix missing pr_cont()s in print_msr_bits() et. al.
powerpc/oops: Fix missing pr_cont()s in show_stack()
powerpc: Fix exception vector build with 2.23 era binutils
powerpc/64s: Fix system reset interrupt winkle wakeups
The ibm_pa_features array consists of structures that describe which bit
and byte in the ibm,pa-features property toggles one or more flags in
either the CPU, MMU, or user visible feature flags.
Each one consists of 7 values, which are all unsigned long, int or char,
meaning the compiler gives us no warning if we assign the wrong values
to the wrong elements. In fact we have had a bug here in the past, where
we were setting incorrect bits, see commit 6997e57d69 ("powerpc:
scan_features() updates incorrect bits for REAL_LE").
So switch to using named initialisers for the structure elements, to
reduce the likelihood of future bugs, and hopefully improve readability
also.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
When ending an oops, don't clear die_owner unless the nest count
went to zero. This prevents a second nested oops from hanging forever
on the die_lock.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When exiting xmon with 'x' (exit and recover), oops_begin bails
out immediately, but die then calls __die() and oops_end(), which
cause a lot of bad things to happen.
If the debugger was attached then went to graceful recovery, exit
from die() immediately.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Remove the unused but set variable srr1 in save_mce_event() to
fix the following GCC warning when building with 'W=1':
arch/powerpc/kernel/mce.c:75:11: warning: variable 'srr1' set but not used
It has never been used.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fix two [-Wold-style-declaration] GCC warnings by moving the inline
keyword before the return type.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit d3cbff1b5 "powerpc: Put exception configuration in a common place"
broke the setting of the AIL bit (which enables taking exceptions with
the MMU still on) on all processors, moving it incorrectly to a function
called only on the boot CPU. This was correct for the guest case but
not when running in hypervisor mode.
This fixes it by partially reverting that commit, putting the setting
back in cpu_ready_for_interrupts()
Fixes: d3cbff1b5a ("powerpc: Put exception configuration in a common place")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Only s390 and powerpc have hardware facilities allowing to measure
cputimes scaled by frequency. On all other architectures
utimescaled/stimescaled are equal to utime/stime (however they are
accounted separately).
Remove {u,s}timescaled accounting on all architectures except
powerpc and s390, where those values are explicitly accounted
in the proper places.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Paul Mackerras <paulus@ozlabs.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20161031162143.GB12646@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Since commit:
cf9efce0ce ("powerpc: Account time using timebase rather than PURR")
cputime_last_delta is not initialized to other value than 0, hence it's
not used except zero check and cputime_to_scaled() just returns
the argument.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Paul Mackerras <paulus@ozlabs.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1479175612-14718-2-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add comment clarifying that vio_find_node() takes a reference to the
embedded struct device which needs to be dropped after use.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Make sure to drop any reference taken by bus_find_device() when creating
devices during init and driver registration.
Fixes: 55347cc996 ("[POWERPC] ibmebus: Add device creation and bus probing based on of_device")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Make sure to drop any reference taken by bus_find_device() in the sysfs
callbacks that are used to create and destroy devices based on
device-tree entries.
Fixes: 6bccf755ff ("[POWERPC] ibmebus: dynamic addition/removal of adapters, some code cleanup")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Load monitored is no longer supported on POWER9 so let's remove the
code.
This reverts commit bd3ea317fd ("powerpc: Load Monitor Register
Support").
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds a config option that can help exercise the case when
the kernel is not running at PAGE_OFFSET.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This halves the exception table size on 64-bit builds, and it allows
build-time sorting of exception tables to work on relocated kernels.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Minor asm fixups and bits to keep the selftests working]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We haven't seen these before, but the soon to be merged relative
exception tables support causes them to be generated.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Exception handlers are aligned to 128 bytes (L1 cache) on 64s, which is
overkill. It can reduce the icache footprint of any individual exception
path. However taken as a whole, the expansion in icache footprint seems
likely to be counter-productive and cause more total misses.
Create IFETCH_ALIGN_SHIFT/BYTES, which should give optimal ifetch
alignment with much more reasonable alignment. This saves 1792 bytes
from head_64.o text with an allmodconfig build.
Other subarchitectures should define appropriate IFETCH_ALIGN_SHIFT
values if this becomes more widely used.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since the KERN_CONT changes, the current code in show_instructions()
prints out a whole bunch of unnecessary newlines. Change occurrences of
printk("\n") to pr_cont("\n"). While we're here, change all the other
cases of printk(KERN_CONT ...) to pr_cont() as well.
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fix up our oops output by converting continuation lines to use
pr_cont(). Some of these are dubious, eg. printing a continuation line
which starts with a newline, but seem to work OK for now. This whole
function needs a rewrite in the next release.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since the KERN_CONT changes these are being horribly split across lines,
for example:
MSR: 8000000000009033 <
SF,EE
,ME,IR
,DR,RI
,LE>
So fix it by using pr_cont() where appropriate.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Previously we got away with printing the stack trace in multiple pieces
and it usually looked right. But since commit 4bcc595ccd ("printk:
reinstate KERN_CONT for printing continuation lines"), KERN_CONT is now
required when printing continuation lines. Use pr_cont() as appropriate.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Wakeups from winkle set the low bit of the HSPRG0 register, to
distinguish it from other sleep states. This is also the PACA pointer.
The system reset exception handler fails to mask this bit away before
using this value before using it as the PACA pointer.
Fix this by adding a new type of exception prolog macro where we already
have the PACA set in r13, and have the system reset vector mask it out.
The winkle wakeup handler will store the masked value back into HSPRG0.
Fixes: fb479e44a9 ("powerpc/64s: relocation, register save fixes for system reset interrupt")
Cc: stable@vger.kernel.org # v3.0+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fixes marked for stable:
- Convert cmp to cmpd in idle enter sequence (Segher Boessenkool)
- cxl: Fix leaking pid refs in some error paths (Vaibhav Jain)
- Re-fix race condition between going idle and entering guest (Paul Mackerras)
- Fix race condition in setting lock bit in idle/wakeup code (Paul Mackerras)
- radix: Use tlbiel only if we ever ran on the current cpu (Aneesh Kumar K.V)
- relocation, register save fixes for system reset interrupt (Nicholas Piggin)
Fixes for code merged this cycle:
- Fix CONFIG_ALIVEC typo in restore_tm_state() (Valentin Rothberg)
- KVM: PPC: Book3S HV: Fix build error when SMP=n (Michael Ellerman)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dnRQ
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.9-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Fixes marked for stable:
- Convert cmp to cmpd in idle enter sequence (Segher Boessenkool)
- cxl: Fix leaking pid refs in some error paths (Vaibhav Jain)
- Re-fix race condition between going idle and entering guest (Paul Mackerras)
- Fix race condition in setting lock bit in idle/wakeup code (Paul Mackerras)
- radix: Use tlbiel only if we ever ran on the current cpu (Aneesh Kumar K.V)
- relocation, register save fixes for system reset interrupt (Nicholas Piggin)
Fixes for code merged this cycle:
- Fix CONFIG_ALIVEC typo in restore_tm_state() (Valentin Rothberg)
- KVM: PPC: Book3S HV: Fix build error when SMP=n (Michael Ellerman)"
* tag 'powerpc-4.9-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64s: relocation, register save fixes for system reset interrupt
powerpc/mm/radix: Use tlbiel only if we ever ran on the current cpu
powerpc/process: Fix CONFIG_ALIVEC typo in restore_tm_state()
powerpc/64: Fix race condition in setting lock bit in idle/wakeup code
powerpc/64: Re-fix race condition between going idle and entering guest
cxl: Fix leaking pid refs in some error paths
powerpc: Convert cmp to cmpd in idle enter sequence
KVM: PPC: Book3S HV: Fix build error when SMP=n
Pull perf fixes from Ingo Molnar:
"Misc kernel fixes: a virtualization environment related fix, an uncore
PMU driver removal handling fix, a PowerPC fix and new events for
Knights Landing"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel: Honour the CPUID for number of fixed counters in hypervisors
perf/powerpc: Don't call perf_event_disable() from atomic context
perf/core: Protect PMU device removal with a 'pmu_bus_running' check, to fix CONFIG_DEBUG_TEST_DRIVER_REMOVE=y kernel panic
perf/x86/intel/cstate: Add C-state residency events for Knights Landing
The trinity syscall fuzzer triggered following WARN() on powerpc:
WARNING: CPU: 9 PID: 2998 at arch/powerpc/kernel/hw_breakpoint.c:278
...
NIP [c00000000093aedc] .hw_breakpoint_handler+0x28c/0x2b0
LR [c00000000093aed8] .hw_breakpoint_handler+0x288/0x2b0
Call Trace:
[c0000002f7933580] [c00000000093aed8] .hw_breakpoint_handler+0x288/0x2b0 (unreliable)
[c0000002f7933630] [c0000000000f671c] .notifier_call_chain+0x7c/0xf0
[c0000002f79336d0] [c0000000000f6abc] .__atomic_notifier_call_chain+0xbc/0x1c0
[c0000002f7933780] [c0000000000f6c40] .notify_die+0x70/0xd0
[c0000002f7933820] [c00000000001a74c] .do_break+0x4c/0x100
[c0000002f7933920] [c0000000000089fc] handle_dabr_fault+0x14/0x48
Followed by a lockdep warning:
===============================
[ INFO: suspicious RCU usage. ]
4.8.0-rc5+ #7 Tainted: G W
-------------------------------
./include/linux/rcupdate.h:556 Illegal context switch in RCU read-side critical section!
other info that might help us debug this:
rcu_scheduler_active = 1, debug_locks = 0
2 locks held by ls/2998:
#0: (rcu_read_lock){......}, at: [<c0000000000f6a00>] .__atomic_notifier_call_chain+0x0/0x1c0
#1: (rcu_read_lock){......}, at: [<c00000000093ac50>] .hw_breakpoint_handler+0x0/0x2b0
stack backtrace:
CPU: 9 PID: 2998 Comm: ls Tainted: G W 4.8.0-rc5+ #7
Call Trace:
[c0000002f7933150] [c00000000094b1f8] .dump_stack+0xe0/0x14c (unreliable)
[c0000002f79331e0] [c00000000013c468] .lockdep_rcu_suspicious+0x138/0x180
[c0000002f7933270] [c0000000001005d8] .___might_sleep+0x278/0x2e0
[c0000002f7933300] [c000000000935584] .mutex_lock_nested+0x64/0x5a0
[c0000002f7933410] [c00000000023084c] .perf_event_ctx_lock_nested+0x16c/0x380
[c0000002f7933500] [c000000000230a80] .perf_event_disable+0x20/0x60
[c0000002f7933580] [c00000000093aeec] .hw_breakpoint_handler+0x29c/0x2b0
[c0000002f7933630] [c0000000000f671c] .notifier_call_chain+0x7c/0xf0
[c0000002f79336d0] [c0000000000f6abc] .__atomic_notifier_call_chain+0xbc/0x1c0
[c0000002f7933780] [c0000000000f6c40] .notify_die+0x70/0xd0
[c0000002f7933820] [c00000000001a74c] .do_break+0x4c/0x100
[c0000002f7933920] [c0000000000089fc] handle_dabr_fault+0x14/0x48
While it looks like the first WARN() is probably valid, the other one is
triggered by disabling event via perf_event_disable() from atomic context.
The event is disabled here in case we were not able to emulate
the instruction that hit the breakpoint. By disabling the event
we unschedule the event and make sure it's not scheduled back.
But we can't call perf_event_disable() from atomic context, instead
we need to use the event's pending_disable irq_work method to disable it.
Reported-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20161026094824.GA21397@krava
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch does a couple of things. First of all, powernv immediately
explodes when running a relocated kernel, because the system reset
exception for handling sleeps does not do correct relocated branches.
Secondly, the sleep handling code trashes the condition and cfar
registers, which we would like to preserve for debugging purposes (for
non-sleep case exception).
This patch changes the exception to use the standard format that saves
registers before any tests or branches are made. It adds the test for
idle-wakeup as an "extra" to break out of the normal exception path.
Then it branches to a relocated idle handler that calls the various
idle handling functions.
After this patch, POWER8 CPU simulator now boots powernv kernel that is
running at non-zero.
Fixes: 948cf67c47 ("powerpc: Add NAP mode support on Power7 in HV mode")
Cc: stable@vger.kernel.org # v3.0+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It should be ALTIVEC, not ALIVEC.
Cyril explains: If a thread performs a transaction with altivec and then
gets preempted for whatever reason, this bug may cause the kernel to not
re-enable altivec when that thread runs again. This will result in an
altivec unavailable fault, when that fault happens inside a user
transaction the kernel has no choice but to enable altivec and doom the
transaction.
The result is that transactions using altivec may get aborted more often
than they should.
The difficulty in catching this with a selftest is my deliberate use of
the word may above. Optimisations to avoid FPU/altivec/VSX faults mean
that the kernel will always leave them on for 255 switches. This code
prevents the kernel turning it off if it got to the 256th switch (and
userspace was transactional).
Fixes: dc16b553c9 ("powerpc: Always restore FPU/VEC/VSX if hardware transactional memory in use")
Reviewed-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This fixes a race condition where one thread that is entering or
leaving a power-saving state can inadvertently ignore the lock bit
that was set by another thread, and potentially also clear it.
The core_idle_lock_held function is called when the lock bit is
seen to be set. It polls the lock bit until it is clear, then
does a lwarx to load the word containing the lock bit and thread
idle bits so it can be updated. However, it is possible that the
value loaded with the lwarx has the lock bit set, even though an
immediately preceding lwz loaded a value with the lock bit clear.
If this happens then we go ahead and update the word despite the
lock bit being set, and when called from pnv_enter_arch207_idle_mode,
we will subsequently clear the lock bit.
No identifiable misbehaviour has been attributed to this race.
This fixes it by checking the lock bit in the value loaded by the
lwarx. If it is set then we just go back and keep on polling.
Fixes: b32aadc1a8 ("powerpc/powernv: Fix race in updating core_idle_state")
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 8117ac6a6c ("powerpc/powernv: Switch off MMU before entering
nap/sleep/rvwinkle mode", 2014-12-10) fixed a race condition where one
thread entering a KVM guest could switch the MMU context to the guest
while another thread was still in host kernel context with the MMU on.
That commit moved the point where a thread entering a power-saving
mode set its kvm_hstate.hwthread_state field in its PACA to
KVM_HWTHREAD_IN_IDLE from a point where the MMU was on to after the
MMU had been switched off. That commit also added a comment
explaining that we have to switch to real mode before setting
hwthread_state to avoid this race.
Nevertheless, commit 4eae2c9ae5 ("powerpc/powernv: Make
pnv_powersave_common more generic", 2016-07-08) subsequently moved
the setting of hwthread_state back to a point where the MMU is on,
thus reintroducing the race, despite the comment saying that this
should not be done being included in full in the context lines of
the patch that did it.
This fixes the race again and adds a bigger and shoutier comment
explaining the potential race condition.
Fixes: 4eae2c9ae5 ("powerpc/powernv: Make pnv_powersave_common more generic")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Shreyas B. Prabhu <shreyasbp@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Merge the gup_flags cleanups from Lorenzo Stoakes:
"This patch series adjusts functions in the get_user_pages* family such
that desired FOLL_* flags are passed as an argument rather than
implied by flags.
The purpose of this change is to make the use of FOLL_FORCE explicit
so it is easier to grep for and clearer to callers that this flag is
being used. The use of FOLL_FORCE is an issue as it overrides missing
VM_READ/VM_WRITE flags for the VMA whose pages we are reading
from/writing to, which can result in surprising behaviour.
The patch series came out of the discussion around commit 38e0885465
("mm: check VMA flags to avoid invalid PROT_NONE NUMA balancing"),
which addressed a BUG_ON() being triggered when a page was faulted in
with PROT_NONE set but having been overridden by FOLL_FORCE.
do_numa_page() was run on the assumption the page _must_ be one marked
for NUMA node migration as an actual PROT_NONE page would have been
dealt with prior to this code path, however FOLL_FORCE introduced a
situation where this assumption did not hold.
See
https://marc.info/?l=linux-mm&m=147585445805166
for the patch proposal"
Additionally, there's a fix for an ancient bug related to FOLL_FORCE and
FOLL_WRITE by me.
[ This branch was rebased recently to add a few more acked-by's and
reviewed-by's ]
* gup_flag-cleanups:
mm: replace access_process_vm() write parameter with gup_flags
mm: replace access_remote_vm() write parameter with gup_flags
mm: replace __access_remote_vm() write parameter with gup_flags
mm: replace get_user_pages_remote() write/force parameters with gup_flags
mm: replace get_user_pages() write/force parameters with gup_flags
mm: replace get_vaddr_frames() write/force parameters with gup_flags
mm: replace get_user_pages_locked() write/force parameters with gup_flags
mm: replace get_user_pages_unlocked() write/force parameters with gup_flags
mm: remove write/force parameters from __get_user_pages_unlocked()
mm: remove write/force parameters from __get_user_pages_locked()
mm: remove gup_flags FOLL_WRITE games from __get_user_pages()
This removes the 'write' argument from access_process_vm() and replaces
it with 'gup_flags' as use of this function previously silently implied
FOLL_FORCE, whereas after this patch callers explicitly pass this flag.
We make this explicit as use of FOLL_FORCE can result in surprising
behaviour (and hence bugs) within the mm subsystem.
Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
extract as much possible uncertainty from a running system at boot time as
possible, hoping to capitalize on any possible variation in CPU operation
(due to runtime data differences, hardware differences, SMP ordering,
thermal timing variation, cache behavior, etc).
At the very least, this plugin is a much more comprehensive example for
how to manipulate kernel code using the gcc plugin internals.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
Comment: Kees Cook <kees@outflux.net>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=1dUK
-----END PGP SIGNATURE-----
Merge tag 'gcc-plugins-v4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull gcc plugins update from Kees Cook:
"This adds a new gcc plugin named "latent_entropy". It is designed to
extract as much possible uncertainty from a running system at boot
time as possible, hoping to capitalize on any possible variation in
CPU operation (due to runtime data differences, hardware differences,
SMP ordering, thermal timing variation, cache behavior, etc).
At the very least, this plugin is a much more comprehensive example
for how to manipulate kernel code using the gcc plugin internals"
* tag 'gcc-plugins-v4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
latent_entropy: Mark functions with __latent_entropy
gcc-plugins: Add latent_entropy plugin
Pull kbuild updates from Michal Marek:
- EXPORT_SYMBOL for asm source by Al Viro.
This does bring a regression, because genksyms no longer generates
checksums for these symbols (CONFIG_MODVERSIONS). Nick Piggin is
working on a patch to fix this.
Plus, we are talking about functions like strcpy(), which rarely
change prototypes.
- Fixes for PPC fallout of the above by Stephen Rothwell and Nick
Piggin
- fixdep speedup by Alexey Dobriyan.
- preparatory work by Nick Piggin to allow architectures to build with
-ffunction-sections, -fdata-sections and --gc-sections
- CONFIG_THIN_ARCHIVES support by Stephen Rothwell
- fix for filenames with colons in the initramfs source by me.
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild: (22 commits)
initramfs: Escape colons in depfile
ppc: there is no clear_pages to export
powerpc/64: whitelist unresolved modversions CRCs
kbuild: -ffunction-sections fix for archs with conflicting sections
kbuild: add arch specific post-link Makefile
kbuild: allow archs to select link dead code/data elimination
kbuild: allow architectures to use thin archives instead of ld -r
kbuild: Regenerate genksyms lexer
kbuild: genksyms fix for typeof handling
fixdep: faster CONFIG_ search
ia64: move exports to definitions
sparc32: debride memcpy.S a bit
[sparc] unify 32bit and 64bit string.h
sparc: move exports to definitions
ppc: move exports to definitions
arm: move exports to definitions
s390: move exports to definitions
m68k: move exports to definitions
alpha: move exports to actual definitions
x86: move exports to actual definitions
...
Add support for the DMA_ATTR_NO_WARN attribute on powerpc iommu code.
Link: http://lkml.kernel.org/r/1470092390-25451-3-git-send-email-mauricfo@linux.vnet.ibm.com
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Jens Axboe <axboe@fb.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
power4_fixup_nap is called from the "common" handlers, not the virt/real
handlers, therefore it should itself be a common handler. Placing it
down in the trampoline space caused it to go out of reach of its
callers, requiring a trampoline inserted at the start of the text
section, which breaks the fixed section address calculations.
Fixes: da2bc4644c ("powerpc/64s: Add new exception vector macros")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Freescale updates from Scott:
"Highlights include qbman support (a prerequisite for datapath drivers
such as ethernet), a PCI DMA fix+improvement, reset handler changes, more
8xx optimizations, and some cleanups and fixes."
This adds a new gcc plugin named "latent_entropy". It is designed to
extract as much possible uncertainty from a running system at boot time as
possible, hoping to capitalize on any possible variation in CPU operation
(due to runtime data differences, hardware differences, SMP ordering,
thermal timing variation, cache behavior, etc).
At the very least, this plugin is a much more comprehensive example for
how to manipulate kernel code using the gcc plugin internals.
The need for very-early boot entropy tends to be very architecture or
system design specific, so this plugin is more suited for those sorts
of special cases. The existing kernel RNG already attempts to extract
entropy from reliable runtime variation, but this plugin takes the idea to
a logical extreme by permuting a global variable based on any variation
in code execution (e.g. a different value (and permutation function)
is used to permute the global based on loop count, case statement,
if/then/else branching, etc).
To do this, the plugin starts by inserting a local variable in every
marked function. The plugin then adds logic so that the value of this
variable is modified by randomly chosen operations (add, xor and rol) and
random values (gcc generates separate static values for each location at
compile time and also injects the stack pointer at runtime). The resulting
value depends on the control flow path (e.g., loops and branches taken).
Before the function returns, the plugin mixes this local variable into
the latent_entropy global variable. The value of this global variable
is added to the kernel entropy pool in do_one_initcall() and _do_fork(),
though it does not credit any bytes of entropy to the pool; the contents
of the global are just used to mix the pool.
Additionally, the plugin can pre-initialize arrays with build-time
random contents, so that two different kernel builds running on identical
hardware will not have the same starting values.
Signed-off-by: Emese Revfy <re.emese@gmail.com>
[kees: expanded commit message and code comments]
Signed-off-by: Kees Cook <keescook@chromium.org>
Merge updates from Andrew Morton:
- fsnotify updates
- ocfs2 updates
- all of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (127 commits)
console: don't prefer first registered if DT specifies stdout-path
cred: simpler, 1D supplementary groups
CREDITS: update Pavel's information, add GPG key, remove snail mail address
mailmap: add Johan Hovold
.gitattributes: set git diff driver for C source code files
uprobes: remove function declarations from arch/{mips,s390}
spelling.txt: "modeled" is spelt correctly
nmi_backtrace: generate one-line reports for idle cpus
arch/tile: adopt the new nmi_backtrace framework
nmi_backtrace: do a local dump_stack() instead of a self-NMI
nmi_backtrace: add more trigger_*_cpu_backtrace() methods
min/max: remove sparse warnings when they're nested
Documentation/filesystems/proc.txt: add more description for maps/smaps
mm, proc: fix region lost in /proc/self/smaps
proc: fix timerslack_ns CAP_SYS_NICE check when adjusting self
proc: add LSM hook checks to /proc/<tid>/timerslack_ns
proc: relax /proc/<tid>/timerslack_ns capability requirements
meminfo: break apart a very long seq_printf with #ifdefs
seq/proc: modify seq_put_decimal_[u]ll to take a const char *, not char
proc: faster /proc/*/status
...
Highlights:
- Major rework of Book3S 64-bit exception vectors (Nicholas Piggin)
- Use gas sections for arranging exception vectors et. al.
- Large set of TM cleanups and selftests (Cyril Bur)
- Enable transactional memory (TM) lazily for userspace (Cyril Bur)
- Support for XZ compression in the zImage wrapper (Oliver O'Halloran)
- Add support for bpf constant blinding (Naveen N. Rao)
- Beginnings of upstream support for PA Semi Nemo motherboards (Darren Stevens)
Fixes:
- Ensure .mem(init|exit).text are within _stext/_etext (Michael Ellerman)
- xmon: Don't use ld on 32-bit (Michael Ellerman)
- vdso64: Use double word compare on pointers (Anton Blanchard)
- powerpc/nvram: Fix an incorrect partition merge (Pan Xinhui)
- powerpc: Fix usage of _PAGE_RO in hugepage (Christophe Leroy)
- powerpc/mm: Update FORCE_MAX_ZONEORDER range to allow hugetlb w/4K (Aneesh Kumar K.V)
- Fix memory leak in queue_hotplug_event() error path (Andrew Donnellan)
- Replay hypervisor maintenance interrupt first (Nicholas Piggin)
Cleanups & features:
- Sparse fixes/cleanups (Daniel Axtens)
- Preserve CFAR value on SLB miss caused by access to bogus address (Paul Mackerras)
- Radix MMU fixups for POWER9 (Aneesh Kumar K.V)
- Support for setting used_(vsr|vr|spe) in sigreturn path (for CRIU) (Simon Guo)
- Optimise syscall entry for virtual, relocatable case (Nicholas Piggin)
- Optimise MSR handling in exception handling (Nicholas Piggin)
- Support for kexec with Radix MMU (Benjamin Herrenschmidt)
- powernv EEH fixes (Russell Currey)
- Suprise PCI hotplug support for powernv (Gavin Shan)
- Endian/sparse fixes for powernv PCI (Gavin Shan)
- Defconfig updates (Anton Blanchard)
- Various performance optimisations (Anton Blanchard)
- Align hot loops of memset() and backwards_memcpy()
- During context switch, check before setting mm_cpumask
- Remove static branch prediction in atomic{, 64}_add_unless
- Only disable HAVE_EFFICIENT_UNALIGNED_ACCESS on POWER7 little endian
- Set default CPU type to POWER8 for little endian builds
- KVM: PPC: Book3S HV: Migrate pinned pages out of CMA (Balbir Singh)
- cxl: Flush PSL cache before resetting the adapter (Frederic Barrat)
- cxl: replace loop with for_each_child_of_node(), remove unneeded of_node_put() (Andrew Donnellan)
- Fix HV facility unavailable to use correct handler (Nicholas Piggin)
- Remove unnecessary syscall trampoline (Nicholas Piggin)
- fadump: Fix build break when CONFIG_PROC_VMCORE=n (Michael Ellerman)
- Quieten EEH message when no adapters are found (Anton Blanchard)
- powernv: Add PHB register dump debugfs handle (Russell Currey)
- Use kprobe blacklist for exception handlers & asm functions (Nicholas Piggin)
- Document the syscall ABI (Nicholas Piggin)
- MAINTAINERS: Update cxl maintainers (Michael Neuling)
- powerpc: Remove all usages of NO_IRQ (Michael Ellerman)
Minor cleanups:
- Andrew Donnellan, Christophe Leroy, Colin Ian King, Cyril Bur, Frederic Barrat,
Pan Xinhui, PrasannaKumar Muralidharan, Rui Teng, Simon Guo.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Jnn8
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights:
- Major rework of Book3S 64-bit exception vectors (Nicholas Piggin)
- Use gas sections for arranging exception vectors et. al.
- Large set of TM cleanups and selftests (Cyril Bur)
- Enable transactional memory (TM) lazily for userspace (Cyril Bur)
- Support for XZ compression in the zImage wrapper (Oliver
O'Halloran)
- Add support for bpf constant blinding (Naveen N. Rao)
- Beginnings of upstream support for PA Semi Nemo motherboards
(Darren Stevens)
Fixes:
- Ensure .mem(init|exit).text are within _stext/_etext (Michael
Ellerman)
- xmon: Don't use ld on 32-bit (Michael Ellerman)
- vdso64: Use double word compare on pointers (Anton Blanchard)
- powerpc/nvram: Fix an incorrect partition merge (Pan Xinhui)
- powerpc: Fix usage of _PAGE_RO in hugepage (Christophe Leroy)
- powerpc/mm: Update FORCE_MAX_ZONEORDER range to allow hugetlb w/4K
(Aneesh Kumar K.V)
- Fix memory leak in queue_hotplug_event() error path (Andrew
Donnellan)
- Replay hypervisor maintenance interrupt first (Nicholas Piggin)
Various performance optimisations (Anton Blanchard):
- Align hot loops of memset() and backwards_memcpy()
- During context switch, check before setting mm_cpumask
- Remove static branch prediction in atomic{, 64}_add_unless
- Only disable HAVE_EFFICIENT_UNALIGNED_ACCESS on POWER7 little
endian
- Set default CPU type to POWER8 for little endian builds
Cleanups & features:
- Sparse fixes/cleanups (Daniel Axtens)
- Preserve CFAR value on SLB miss caused by access to bogus address
(Paul Mackerras)
- Radix MMU fixups for POWER9 (Aneesh Kumar K.V)
- Support for setting used_(vsr|vr|spe) in sigreturn path (for CRIU)
(Simon Guo)
- Optimise syscall entry for virtual, relocatable case (Nicholas
Piggin)
- Optimise MSR handling in exception handling (Nicholas Piggin)
- Support for kexec with Radix MMU (Benjamin Herrenschmidt)
- powernv EEH fixes (Russell Currey)
- Suprise PCI hotplug support for powernv (Gavin Shan)
- Endian/sparse fixes for powernv PCI (Gavin Shan)
- Defconfig updates (Anton Blanchard)
- KVM: PPC: Book3S HV: Migrate pinned pages out of CMA (Balbir Singh)
- cxl: Flush PSL cache before resetting the adapter (Frederic Barrat)
- cxl: replace loop with for_each_child_of_node(), remove unneeded
of_node_put() (Andrew Donnellan)
- Fix HV facility unavailable to use correct handler (Nicholas
Piggin)
- Remove unnecessary syscall trampoline (Nicholas Piggin)
- fadump: Fix build break when CONFIG_PROC_VMCORE=n (Michael
Ellerman)
- Quieten EEH message when no adapters are found (Anton Blanchard)
- powernv: Add PHB register dump debugfs handle (Russell Currey)
- Use kprobe blacklist for exception handlers & asm functions
(Nicholas Piggin)
- Document the syscall ABI (Nicholas Piggin)
- MAINTAINERS: Update cxl maintainers (Michael Neuling)
- powerpc: Remove all usages of NO_IRQ (Michael Ellerman)
Minor cleanups:
- Andrew Donnellan, Christophe Leroy, Colin Ian King, Cyril Bur,
Frederic Barrat, Pan Xinhui, PrasannaKumar Muralidharan, Rui Teng,
Simon Guo"
* tag 'powerpc-4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (156 commits)
powerpc/bpf: Add support for bpf constant blinding
powerpc/bpf: Implement support for tail calls
powerpc/bpf: Introduce accessors for using the tmp local stack space
powerpc/fadump: Fix build break when CONFIG_PROC_VMCORE=n
powerpc: tm: Enable transactional memory (TM) lazily for userspace
powerpc/tm: Add TM Unavailable Exception
powerpc: Remove do_load_up_transact_{fpu,altivec}
powerpc: tm: Rename transct_(*) to ck(\1)_state
powerpc: tm: Always use fp_state and vr_state to store live registers
selftests/powerpc: Add checks for transactional VSXs in signal contexts
selftests/powerpc: Add checks for transactional VMXs in signal contexts
selftests/powerpc: Add checks for transactional FPUs in signal contexts
selftests/powerpc: Add checks for transactional GPRs in signal contexts
selftests/powerpc: Check that signals always get delivered
selftests/powerpc: Add TM tcheck helpers in C
selftests/powerpc: Allow tests to extend their kill timeout
selftests/powerpc: Introduce GPR asm helper header file
selftests/powerpc: Move VMX stack frame macros to header file
selftests/powerpc: Rework FPU stack placement macros and move to header file
selftests/powerpc: Check for VSX preservation across userspace preemption
...
When doing an nmi backtrace of many cores, most of which are idle, the
output is a little overwhelming and very uninformative. Suppress
messages for cpus that are idling when they are interrupted and just
emit one line, "NMI backtrace for N skipped: idling at pc 0xNNN".
We do this by grouping all the cpuidle code together into a new
.cpuidle.text section, and then checking the address of the interrupted
PC to see if it lies within that section.
This commit suitably tags x86 and tile idle routines, and only adds in
the minimal framework for other architectures.
Link: http://lkml.kernel.org/r/1472487169-14923-5-git-send-email-cmetcalf@mellanox.com
Signed-off-by: Chris Metcalf <cmetcalf@mellanox.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Daniel Thompson <daniel.thompson@linaro.org> [arm]
Tested-by: Petr Mladek <pmladek@suse.com>
Cc: Aaron Tomlin <atomlin@redhat.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently significant amount of memory is reserved only in kernel booted
to capture kernel dump using the fa_dump method.
Kernels compiled with CONFIG_DEFERRED_STRUCT_PAGE_INIT will initialize
only certain size memory per node. The certain size takes into account
the dentry and inode cache sizes. Currently the cache sizes are
calculated based on the total system memory including the reserved
memory. However such a kernel when booting the same kernel as fadump
kernel will not be able to allocate the required amount of memory to
suffice for the dentry and inode caches. This results in crashes like
Hence only implement arch_reserved_kernel_pages() for CONFIG_FA_DUMP
configurations. The amount reserved will be reduced while calculating
the large caches and will avoid crashes like the below on large systems
such as 32 TB systems.
Dentry cache hash table entries: 536870912 (order: 16, 4294967296 bytes)
vmalloc: allocation failure, allocated 4097114112 of 17179934720 bytes
swapper/0: page allocation failure: order:0, mode:0x2080020(GFP_ATOMIC)
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.6-master+ #3
Call Trace:
dump_stack+0xb0/0xf0 (unreliable)
warn_alloc_failed+0x114/0x160
__vmalloc_node_range+0x304/0x340
__vmalloc+0x6c/0x90
alloc_large_system_hash+0x1b8/0x2c0
inode_init+0x94/0xe4
vfs_caches_init+0x8c/0x13c
start_kernel+0x50c/0x578
start_here_common+0x20/0xa8
Link: http://lkml.kernel.org/r/1472476010-4709-4-git-send-email-srikar@linux.vnet.ibm.com
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Suggested-by: Mel Gorman <mgorman@techsingularity.net>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Cc: Hari Bathini <hbathini@linux.vnet.ibm.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All architectures:
Move `make kvmconfig` stubs from x86; use 64 bits for debugfs stats.
ARM:
Important fixes for not using an in-kernel irqchip; handle SError
exceptions and present them to guests if appropriate; proxying of GICV
access at EL2 if guest mappings are unsafe; GICv3 on AArch32 on ARMv8;
preparations for GICv3 save/restore, including ABI docs; cleanups and
a bit of optimizations.
MIPS:
A couple of fixes in preparation for supporting MIPS EVA host kernels;
MIPS SMP host & TLB invalidation fixes.
PPC:
Fix the bug which caused guests to falsely report lockups; other minor
fixes; a small optimization.
s390:
Lazy enablement of runtime instrumentation; up to 255 CPUs for nested
guests; rework of machine check deliver; cleanups and fixes.
x86:
IOMMU part of AMD's AVIC for vmexit-less interrupt delivery; Hyper-V
TSC page; per-vcpu tsc_offset in debugfs; accelerated INS/OUTS in
nVMX; cleanups and fixes.
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJX9iDrAAoJEED/6hsPKofoOPoIAIUlgojkb9l2l1XVDgsXdgQL
sRVhYSVv7/c8sk9vFImrD5ElOPZd+CEAIqFOu45+NM3cNi7gxip9yftUVs7wI5aC
eDZRWm1E4trDZLe54ZM9ThcqZzZZiELVGMfR1+ZndUycybwyWzafpXYsYyaXp3BW
hyHM3qVkoWO3dxBWFwHIoO/AUJrWYkRHEByKyvlC6KPxSdBPSa5c1AQwMCoE0Mo4
K/xUj4gBn9eMelNhg4Oqu/uh49/q+dtdoP2C+sVM8bSdquD+PmIeOhPFIcuGbGFI
B+oRpUhIuntN39gz8wInJ4/GRSeTuR2faNPxMn4E1i1u4LiuJvipcsOjPfe0a18=
=fZRB
-----END PGP SIGNATURE-----
Merge tag 'kvm-4.9-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Radim Krčmář:
"All architectures:
- move `make kvmconfig` stubs from x86
- use 64 bits for debugfs stats
ARM:
- Important fixes for not using an in-kernel irqchip
- handle SError exceptions and present them to guests if appropriate
- proxying of GICV access at EL2 if guest mappings are unsafe
- GICv3 on AArch32 on ARMv8
- preparations for GICv3 save/restore, including ABI docs
- cleanups and a bit of optimizations
MIPS:
- A couple of fixes in preparation for supporting MIPS EVA host
kernels
- MIPS SMP host & TLB invalidation fixes
PPC:
- Fix the bug which caused guests to falsely report lockups
- other minor fixes
- a small optimization
s390:
- Lazy enablement of runtime instrumentation
- up to 255 CPUs for nested guests
- rework of machine check deliver
- cleanups and fixes
x86:
- IOMMU part of AMD's AVIC for vmexit-less interrupt delivery
- Hyper-V TSC page
- per-vcpu tsc_offset in debugfs
- accelerated INS/OUTS in nVMX
- cleanups and fixes"
* tag 'kvm-4.9-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (140 commits)
KVM: MIPS: Drop dubious EntryHi optimisation
KVM: MIPS: Invalidate TLB by regenerating ASIDs
KVM: MIPS: Split kernel/user ASID regeneration
KVM: MIPS: Drop other CPU ASIDs on guest MMU changes
KVM: arm/arm64: vgic: Don't flush/sync without a working vgic
KVM: arm64: Require in-kernel irqchip for PMU support
KVM: PPC: Book3s PR: Allow access to unprivileged MMCR2 register
KVM: PPC: Book3S PR: Support 64kB page size on POWER8E and POWER8NVL
KVM: PPC: Book3S: Remove duplicate setting of the B field in tlbie
KVM: PPC: BookE: Fix a sanity check
KVM: PPC: Book3S HV: Take out virtual core piggybacking code
KVM: PPC: Book3S: Treat VTB as a per-subcore register, not per-thread
ARM: gic-v3: Work around definition of gic_write_bpr1
KVM: nVMX: Fix the NMI IDT-vectoring handling
KVM: VMX: Enable MSR-BASED TPR shadow even if APICv is inactive
KVM: nVMX: Fix reload apic access page warning
kvmconfig: add virtio-gpu to config fragment
config: move x86 kvm_guest.config to a common location
arm64: KVM: Remove duplicating init code for setting VMID
ARM: KVM: Support vgic-v3
...
The fadump code calls vmcore_cleanup() which only exists if
CONFIG_PROC_VMCORE=y. We don't want to depend on CONFIG_PROC_VMCORE,
because it's user selectable, so just wrap the call in an #ifdef.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently the MSR TM bit is always set if the hardware is TM capable.
This adds extra overhead as it means the TM SPRS (TFHAR, TEXASR and
TFAIR) must be swapped for each process regardless of if they use TM.
For processes that don't use TM the TM MSR bit can be turned off
allowing the kernel to avoid the expensive swap of the TM registers.
A TM unavailable exception will occur if a thread does use TM and the
kernel will enable MSR_TM and leave it so for some time afterwards.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If the kernel disables transactional memory (TM) and userspace still
tries TM related actions (TM instructions or TM SPR accesses) TM aware
hardware will cause the kernel to take a facility unavailable
exception.
Add checks for the exception being caused by illegal TM access in
userspace.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
[mpe: Rewrite comment entirely, bugs in it are mine]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Make the structures being used for checkpointed state named
consistently with the pt_regs/ckpt_regs.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There is currently an inconsistency as to how the entire CPU register
state is saved and restored when a thread uses transactional memory
(TM).
Using transactional memory results in the CPU having duplicated
(almost) all of its register state. This duplication results in a set
of registers which can be considered 'live', those being currently
modified by the instructions being executed and another set that is
frozen at a point in time.
On context switch, both sets of state have to be saved and (later)
restored. These two states are often called a variety of different
things. Common terms for the state which only exists after the CPU has
entered a transaction (performed a TBEGIN instruction) in hardware are
'transactional' or 'speculative'.
Between a TBEGIN and a TEND or TABORT (or an event that causes the
hardware to abort), regardless of the use of TSUSPEND the
transactional state can be referred to as the live state.
The second state is often to referred to as the 'checkpointed' state
and is a duplication of the live state when the TBEGIN instruction is
executed. This state is kept in the hardware and will be rolled back
to on transaction failure.
Currently all the registers stored in pt_regs are ALWAYS the live
registers, that is, when a thread has transactional registers their
values are stored in pt_regs and the checkpointed state is in
ckpt_regs. A strange opposite is true for fp_state/vr_state. When a
thread is non transactional fp_state/vr_state holds the live
registers. When a thread has initiated a transaction fp_state/vr_state
holds the checkpointed state and transact_fp/transact_vr become the
structure which holds the live state (at this point it is a
transactional state).
This method creates confusion as to where the live state is, in some
circumstances it requires extra work to determine where to put the
live state and prevents the use of common functions designed (probably
before TM) to save the live state.
With this patch pt_regs, fp_state and vr_state all represent the
same thing and the other structures [pending rename] are for
checkpointed state.
Acked-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Much of the signal code takes a pt_regs on which it operates. Over
time the signal code has needed to know more about the thread than
what pt_regs can supply, this information is obtained as needed by
using 'current'.
This approach is not strictly incorrect however it does mean that
there is now a hard requirement that the pt_regs being passed around
does belong to current, this is never checked. A safer approach is for
the majority of the signal functions to take a task_struct from which
they can obtain pt_regs and any other information they need. The
caveat that the task_struct they are passed must be current doesn't go
away but can more easily be checked for.
Functions called from outside powerpc signal code are passed a pt_regs
and they can confirm that the pt_regs is that of current and pass
current to other functions, furthurmore, powerpc signal functions can
check that the task_struct they are passed is the same as current
avoiding possible corruption of current (or the task they are passed)
if this assertion ever fails.
CC: paulus@samba.org
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
After a thread is reclaimed from its active or suspended transactional
state the checkpointed state exists on CPU, this state (along with the
live/transactional state) has been saved in its entirety by the
reclaiming process.
There exists a sequence of events that would cause the kernel to call
one of enable_kernel_fp(), enable_kernel_altivec() or
enable_kernel_vsx() after a thread has been reclaimed. These functions
save away any user state on the CPU so that the kernel can use the
registers. Not only is this saving away unnecessary at this point, it
is actually incorrect. It causes a save of the checkpointed state to
the live structures within the thread struct thus destroying the true
live state for that thread.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
msr_check_and_set() always performs a mfmsr() to determine if it needs
to perform an mtmsr(), as mfmsr() can be a costly operation
msr_check_and_set() could return the MSR now on the CPU to avoid
callers of msr_check_and_set having to make their own mfmsr() call.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
giveup_all() causes FPU/VMX/VSX facilities to be disabled in a threads
MSR. If the thread performing the giveup was transactional, the kernel
must record which facilities were in use before the giveup as the
thread must have these facilities re-enabled on return to userspace.
>From process.c:
/*
* This is called if we are on the way out to userspace and the
* TIF_RESTORE_TM flag is set. It checks if we need to reload
* FP and/or vector state and does so if necessary.
* If userspace is inside a transaction (whether active or
* suspended) and FP/VMX/VSX instructions have ever been enabled
* inside that transaction, then we have to keep them enabled
* and keep the FP/VMX/VSX state loaded while ever the transaction
* continues. The reason is that if we didn't, and subsequently
* got a FP/VMX/VSX unavailable interrupt inside a transaction,
* we don't know whether it's the same transaction, and thus we
* don't know which of the checkpointed state and the transactional
* state to use.
*/
Calling check_if_tm_restore_required() will set TIF_RESTORE_TM and
save the MSR if needed.
Fixes: c208505 ("powerpc: create giveup_all()")
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Comment from arch/powerpc/kernel/process.c:967:
If userspace is inside a transaction (whether active or
suspended) and FP/VMX/VSX instructions have ever been enabled
inside that transaction, then we have to keep them enabled
and keep the FP/VMX/VSX state loaded while ever the transaction
continues. The reason is that if we didn't, and subsequently
got a FP/VMX/VSX unavailable interrupt inside a transaction,
we don't know whether it's the same transaction, and thus we
don't know which of the checkpointed state and the ransactional
state to use.
restore_math() restore_fp() and restore_altivec() currently may not
restore the registers. It doesn't appear that this is more serious
than a performance penalty. If the math registers aren't restored the
userspace thread will still be run with the facility disabled.
Userspace will not be able to read invalid values. On the first access
it will take an facility unavailable exception and the kernel will
detected an active transaction, at which point it will abort the
transaction. There is the possibility for a pathological case
preventing any progress by transactions, however, transactions
are never guaranteed to make progress.
Fixes: 70fe3d9 ("powerpc: Restore FPU/VEC/VSX if previously used")
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
No real need for this to be pr_warn(), reduce it to pr_info().
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This was not done before the big patches because I only noticed
them afterwards. It has become much easier to see which handlers
are branched to from which exception vectors now, and to see
exactly what vector space is being used for what.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Simple substitution. This is possible now that both parts of the OOL
initial handler get linked into their correct location.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This is not an exception handler as such, it's called from
local_irq_enable(), not exception entry.
Also clean up some now redundant comments at the end of the
consolidation series.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use assembler sections of fixed size and location to arrange the 64-bit
Book3S exception vector code (64-bit Book3E also uses it in head_64.S
for 0x0..0x100).
This allows better flexibility in arranging exception code and hiding
unimportant details behind macros.
Gas sections can be a bit painful to use this way, mainly because the
assembler does not know where they will be finally linked. Taking
absolute addresses requires a bit of trickery for example, but it can
be hidden behind macros for the most part.
Generated code is mostly the same except locations, offsets, alignments.
The "+ 0x2" is only required for the trap number / kvm exit number,
which gets loaded as a constant into a register.
Previously, code also used + 0x2 for label names, but we changed to
using "H" to distinguish HV case for that. Remove the last vestiges
of that.
__after_prom_start is taking absolute address of a label in another
fixed section. Newer toolchains seemed to compile this okay, but older
ones do not. FIXED_SYMBOL_ABS_ADDR is more foolproof, it just takes an
additional line to define.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With a subsequent patch to put text into different sections,
(_end - _stext) can no longer be computed at link time to determine
the end of the copy. Instead, calculate it at runtime with
(copy_to_here - _stext) + (_end - copy_to_here).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move exception handler alignment directives into the head-64.h macros,
beause they will no longer work in-place after the next patch. This
slightly changes functions that have alignments applied and therefore
code generation, which is why it was not done initially (see earlier
patch).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Create arch/powerpc/include/asm/head-64.h with macros that specify
an exception vector (name, type, location), which will be used to
label and lay out exceptions into the object file.
Naming is moved out of exception-64s.h, which is used to specify the
implementation of exception handlers.
objdump of generated code in exception vectors is unchanged except for
names. Alignment directives scattered around are annoying, but done
this way so that disassembly can verify identical instruction
generation before and after patch. These get cleaned up in future
patch.
We change the way KVMTEST works, explicitly passing EXC_HV or EXC_STD
rather than overloading the trap number. This removes the need to have
SOFTEN values for the overloaded trap numbers, eg. 0x502.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
__kernel_get_syscall_map() and __kernel_clock_getres() use cmpli to
check if the passed in pointer is non zero. cmpli maps to a 32 bit
compare on binutils, so we ignore the top 32 bits.
A simple test case can be created by passing in a bogus pointer with
the bottom 32 bits clear. Using a clk_id that is handled by the VDSO,
then one that is handled by the kernel shows the problem:
printf("%d\n", clock_getres(CLOCK_REALTIME, (void *)0x100000000));
printf("%d\n", clock_getres(CLOCK_BOOTTIME, (void *)0x100000000));
And we get:
0
-1
The bigger issue is if we pass a valid pointer with the bottom 32 bits
clear, in this case we will return success but won't write any data
to the pointer.
I stumbled across this issue because the LLVM integrated assembler
doesn't accept cmpli with 3 arguments. Fix this by converting them to
cmpldi.
Fixes: a7f290dad3 ("[PATCH] powerpc: Merge vdso's and add vdso support to 32 bits kernel")
Cc: stable@vger.kernel.org # v2.6.15+
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This exports eeh_pe_state_mark(). It will be used to mark the surprise
hot removed PE as isolated to avoid unexpected EEH error reporting in
surprise remove path.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This exports @confirm_error_lock so that eeh_serialize_{lock, unlock}()
can be used to freeze the affected PE in PCI surprise hot remove path.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Function eeh_pe_set_option() is used to apply the requested options
(enable, disable, unfreeze) in EEH virtualization path. The semantics
of this function isn't complete until freezing is supported.
This allows to freeze the indicated PE. The new semantics is going to
be used in PCI surprise hot remove path, to freeze removed PCI devices
(PE) to avoid unexpected EEH error reporting.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER8 has one virtual timebase (VTB) register per subcore, not one
per CPU thread. The HV KVM code currently treats VTB as a per-thread
register, which can lead to spurious soft lockup messages from guests
which use the VTB as the time source for the soft lockup detector.
(CPUs before POWER8 did not have the VTB register.)
For HV KVM, this fixes the problem by making only the primary thread
in each virtual core save and restore the VTB value. With this,
the VTB state becomes part of the kvmppc_vcore structure. This
also means that "piggybacking" of multiple virtual cores onto one
subcore is not possible on POWER8, because then the virtual cores
would share a single VTB register.
PR KVM emulates a VTB register, which is per-vcpu because PR KVM
has no notion of CPU threads or SMT. For PR KVM we move the VTB
state into the kvmppc_vcpu_book3s struct.
Cc: stable@vger.kernel.org # v3.14+
Reported-by: Thomas Huth <thuth@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
User space DTLB miss represent approximatly 90% of TLB misses
so make it the shortest path.
Also remove an unneccessary double jump in FixupDAR
Before this patch, we spend 3.3 TB ticks in the handler for each
user address miss and 3.4 TB ticks for each kernel address miss
After this patch, we send 3.0 TB ticks in the handler for each
user address miss and 3.9 TB ticks for each kernel address miss
Taking into account that user misses represent 90% of the total,
this patch provides an improvement of approx. 9%
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
When all options are activated, there is not enough space for the
DTLBMiss handlers that handles IMMR area and linear RAM pages in
the exception area once we have added hugepage handling.
So lets move them after .0x2000
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
During a machine check, the 8xx provides indication of
whether the check is due to data or instruction access, so
let's display it.
Lets also move 8xx specific handling into the new handler.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
When the watchdog is in NMI mode, the system reset interrupt is
generated when the watchdog counter expires.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
Call out to all restart handlers that were added via
register_restart_handler() API when restarting the machine.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Scott Wood <oss@buserror.net>
Factor out a small bit of common code in machine_restart(),
machine_power_off() and machine_halt().
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Scott Wood <oss@buserror.net>
CLR_TOP32() is defined as blank. Last useful instance of CLR_TOP32()
was removed by commit 40ef8cbc6d ("powerpc: Get 64-bit configs to
compile with ARCH=powerpc") in 2005.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In eeh_handle_special_event(), eeh_pe_bus_get() is called before calling
eeh_report_failure() on every device under a PE. If a PE was missing a
bus for some reason, the error would occur before reporting failure, even
though eeh_report_failure() doesn't require a bus.
Fix this by moving the bus retrieval and error check after the
eeh_report_failure() calls.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
eeh_pe_bus_get() can return NULL if a PCI bus isn't found for a given PE.
Some callers don't check this, and can cause a null pointer dereference
under certain circumstances.
Fix this by checking NULL everywhere eeh_pe_bus_get() is called.
Fixes: 8a6b1bc70d ("powerpc/eeh: EEH core to handle special event")
Cc: stable@vger.kernel.org # v3.11+
Signed-off-by: Russell Currey <ruscur@russell.cc>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When we originally added the ability to split the exception vectors from
the kernel (commit 1f6a93e4c3 ("powerpc: Make it possible to move the
interrupt handlers away from the kernel" 2008-09-15)), the LOAD_HANDLER() macro
used an addi instruction to compute the offset of the common handler
from the kernel base address.
Using addi meant the handler had to be within 32K of the kernel base
address, due to the addi instruction taking a signed immediate value.
That necessitated creating a trampoline for the system call handler,
because system_call_common (in entry64.S) is not linked within 32K of
the kernel base address.
Later in commit 61e2390ede ("powerpc: Make load_hander handle upto 64k
offset" 2012-11-15) we changed LOAD_HANDLER to take a 64K offset, by
changing it to use ori.
Although system_call_common is not in head_64.S or exceptions-64s.S, it
is included in head-y, which causes it to be linked early in the kernel
text, so in practice it ends up below 64K. Additionally if it can't be
placed below 64K the linker will fail to build with a "relocation
truncated to fit" error.
So remove the trampoline.
Newer toolchains are able to work out that the ori in LOAD_HANDLER only
takes a 16 bit offset, and so they generate a 16 bit relocation. Older
toolchains (binutils 2.22 at least) are not so smart, so we have to add
the @l annotation to tell the assembler to generate a 16 bit relocation.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The 0xf80 hv_facility_unavailable trampoline branches to the 0xf60
handler. This works because they both do the same thing, but it should
be fixed.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The only difference is now the TCE table check which doesn't need
to be ifdef'ed out, it will basically do nothing on BookE (it is
only useful for ancient IBM machines).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently we turn the MMU off after copying the image, and we make
sure there is no overlap between the hash table and the target pages
in that case.
That doesn't work for Radix however. In that case, the page tables
are scattered and we can't really enforce that the target of the
image isn't overlapping one of them.
So instead, let's turn the MMU off before copying the image in radix
mode. Thankfully, in radix mode, even under a hypervisor, we know we
don't have the same kind of RMA limitations that hash mode has.
While at it, also turn the MMU off early when using hash in non-LPAR
mode, that way we can get rid of the collision check completely.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Just using the hash ops won't work anymore since radix will have
NULL in there. Instead create an mmu_cleanup_all() function which
will do the right thing based on the MMU mode.
For Radix, for now I clear UPRT and the PTCR, effectively switching
back to Radix with no partition table setup.
Currently set it to NULL on BookE thought it might be a good idea
to wipe the TLB there (Scott ?)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With Radix, it can be NULL even on !BOOKE these days so replace
the ifdef with a NULL check which is cleaner anyway.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fixes: 9445aa1a30 ("ppc: move exports to definitions")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Michal Marek <mmarek@suse.com>
NO_IRQ has been == 0 on powerpc for just over ten years (since commit
0ebfff1491 ("[POWERPC] Add new interrupt mapping core and change
platforms to use it")). It's also 0 on most other arches.
Although it's fairly harmless, every now and then it causes confusion
when a driver is built on powerpc and another arch which doesn't define
NO_IRQ. There's at least 6 definitions of NO_IRQ in drivers/, at least
some of which are to work around that problem.
So we'd like to remove it. This is fairly trivial in the arch code, we
just convert:
if (irq == NO_IRQ) to if (!irq)
if (irq != NO_IRQ) to if (irq)
irq = NO_IRQ; to irq = 0;
return NO_IRQ; to return 0;
And a few other odd cases as well.
At least for now we keep the #define NO_IRQ, because there is driver
code that uses NO_IRQ and the fixes to remove those will go via other
trees.
Note we also change some occurrences in PPC sound drivers, drivers/ps3,
and drivers/macintosh.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When we merge two contiguous partitions whose signatures are marked
NVRAM_SIG_FREE, We need update prev's length and checksum, then write it
to nvram, not cur's. So lets fix this mistake now.
Also use memset instead of strncpy to set the partition's name. It's
more readable if we want to fill up with duplicate chars .
Fixes: fa2b4e54d4 ("powerpc/nvram: Improve partition removal")
Signed-off-by: Pan Xinhui <xinhui.pan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If kmemdup fails, We need kfree *buff* first then return -ENOMEM.
Otherwise there is a memory leak.
Signed-off-by: Pan Xinhui <xinhui.pan@linux.vnet.ibm.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
mtmsrd with L=1 only affects MSR_EE and MSR_RI bits, and we always
know what state those bits are, so the kernel MSR does not need to be
loaded when modifying them.
mtmsrd is often in the critical execution path, so avoiding dependency
on even L1 load is noticable. On a POWER8 this saves about 3 cycles
from the syscall path, and possibly a few from other exception returns
(not measured).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The mflr r10 instruction was left over from when the code used LR to
branch to system_call_entry from the exception handler. That was
changed by commit 6a404806df ("powerpc: Avoid link stack corruption in
MMU on syscall entry path") to use the count register. The value is
never used now, so mflr can be removed, and r10 can be used for storage
rather than spilling to the SPR scratch register.
The scratch register spill causes a long pipeline stall due to the SPR
read after write. This change brings getppid syscall cost from 406 to
376 cycles on POWER8. getppid for non-relocatable case is 371 cycles.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The HMI (Hypervisor Maintenance Interrupt) is defined by the
architecture to be higher priority than other maskable interrupts, so
replay it first, as a best-effort to replay according to hardware
priorities.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In our linker script we open code the list of text sections, because we
need to include the __ftr_alt sections, which are arch-specific.
This means we can't use TEXT_TEXT as defined in vmlinux.lds.h, and so we
don't have the MEM_KEEP() logic for memory hotplug sections.
If we build the kernel with the gold linker, and with CONFIG_MEMORY_HOTPLUG=y,
we see that functions marked __meminit can end up outside of the
_stext/_etext range, and also outside of _sinittext/_einittext, eg:
c000000000000000 T _stext
c0000000009e0000 A _etext
c0000000009e3f18 T hash__vmemmap_create_mapping
c000000000ca0000 T _sinittext
c000000000d00844 T _einittext
This causes them to not be recognised as text by is_kernel_text(), and
prevents them being patched by jump_label (and presumably ftrace/kprobes
etc.).
Fix it by adding MEM_KEEP() directives, mirroring what TEXT_TEXT does.
This isn't a problem when CONFIG_MEMORY_HOTPLUG=n, because we use the
standard INIT_TEXT_SECTION() and EXIT_TEXT macros from vmlinux.lds.h.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Tested-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Rather than forcing the whole function into the ".kprobes.text" section,
just add the symbol's address to the kprobe blacklist.
This also lets us drop the three versions of the_KPROBE macro, in
exchange for just one version of _ASM_NOKPROBE_SYMBOL - which is a good
cleanup.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently we mark the C implementations of some exception handlers as
__kprobes. This has the effect of putting them in the ".kprobes.text"
section, which separates them from the rest of the text.
Instead we can use the blacklist macros to add the symbols to a
blacklist which kprobes will check. This allows the linker to move
exception handler functions close to callers and avoids trampolines in
larger kernels.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Reword change log a bit]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Normally, when MSR[VSX/VR/SPE] bits == 1, the used_vsr/used_vr/used_spe
bit have already been set. However when loading a signal frame from user
space we need to explicitly set used_vsr/used_vr/used_spe to make them
consistent with the MSR bits from the signal frame.
For example, CRIU application, who utilizes sigreturn to restore
checkpointed process, will lead to the case where MSR[VSX] bit is active
in signal frame, but used_vsr bit is not set in the kernel. (the same
applies to VR/SPE).
This patch fixes this by always setting used_* bit when MSR related bits
are active in signal frame and we are doing sigreturn.
Based on a proposal by Benh.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
[mpe: Massage change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The ckpt_regs usage in gpr32_set_common/gpr32_get_common() will lead to
following cppcheck error at ifndef CONFIG_PPC_TRANSACTIONAL_MEM case:
[arch/powerpc/kernel/ptrace.c:2062]:
(error) Uninitialized variable: ckpt_regs
[arch/powerpc/kernel/ptrace.c:2130]:
(error) Uninitialized variable: ckpt_regs
The problem is due to gpr32_set_common() used ckpt_regs variable which
only makes sense at #ifdef CONFIG_PPC_TRANSACTIONAL_MEM.
This patch fix this issue by passing in "regs" parameter instead.
Reported-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The of_node for the SB600 (io-bridge) has its device_type set to
'io-bridge' Set it to 'isa' so that it can be found by
isa_bridge_find_early() instead of using patches in the kernel.
Signed-off-by: Darren Stevens <darren@stevens-zone.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The device tree on the Nemo passes all of the i8259 interrupts with
numbers between 212 and 222, and points their interrupt-parent property
to the pasemi-opic, requiring custom patches to the kernel. Fix the
values so that they can be controlled by the generic ppc i8259 code.
Signed-off-by: Darren Stevens <darren@stevens-zone.net>
[mpe: Rework deeply nested if and boundary checks]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 2578bfae84 ("[POWERPC] Create and use CONFIG_WORD_SIZE") added
CONFIG_WORD_SIZE, and suggests that other arches were going to do
likewise.
But that never happened, powerpc is the only architecture which uses it.
So switch to using a simple make variable, BITS, like x86, sh, sparc and
tile. It is also easier to spell and simpler, avoiding any confusion
about whether it's defined due to ordering of make vs kconfig.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The LOAD_HANDLER macro requires that you have previously loaded "reg"
with PACAKBASE. Although that gives callers flexibility to get PACAKBASE
in some interesting way, none of the callers actually do that. So fold
the load of PACAKBASE into the macro, making it simpler for callers to
use correctly.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Nick Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently, if userspace or the kernel accesses a completely bogus address,
for example with any of bits 46-59 set, we first take an SLB miss interrupt,
install a corresponding SLB entry with VSID 0, retry the instruction, then
take a DSI/ISI interrupt because there is no HPT entry mapping the address.
However, by the time of the second interrupt, the Come-From Address Register
(CFAR) has been overwritten by the rfid instruction at the end of the SLB
miss interrupt handler. Since bogus accesses can often be caused by a
function return after the stack has been overwritten, the CFAR value would
be very useful as it could indicate which function it was whose return had
led to the bogus address.
This patch adds code to create a full exception frame in the SLB miss handler
in the case of a bogus address, rather than inserting an SLB entry with a
zero VSID field. Then we call a new slb_miss_bad_addr() function in C code,
which delivers a signal for a user access or creates an oops for a kernel
access. In the latter case the oops message will show the CFAR value at the
time of the access.
In the case of the radix MMU, a segment miss interrupt indicates an access
outside the ranges mapped by the page tables. Previously this was handled
by the code for an unrecoverable SLB miss (one with MSR[RI] = 0), which is
not really correct. With this patch, we now handle these interrupts with
slb_miss_bad_addr(), which is much more consistent.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Another set of things that are only called from assembler and so need
prototypes to keep sparse happy.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Firmware Assisted Dump is a facility to dump kernel core with assistance
from firmware. As part of this process the kernel ELF ABI version is
stored in the core file.
Currently fadump.h defines this to 0 if it is not already defined. This
clashes with a define in elf.h which sets it based on the current task -
not based on the kernel's ELF ABI version.
Use the compiler-provided #define _CALL_ELF which tells us the ELF ABI
version of the kernel to set e_flags, this matches what binutils does.
Remove the definition in fadump.h, which becomes unused.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Reviewed-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Squash a bunch of sparse warnings by making things static.
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
pnv_wakeup_tb_loss() currently expects cr4 to be "eq" if the CPU is
waking up from a complete hypervisor state loss. Hence, it currently
restores the SPR contents only if cr4 is "eq".
However, after commit bcef83a00d ("powerpc/powernv: Add platform
support for stop instruction"), on ISA v3.0 CPUs, the function
pnv_restore_hyp_resource() sets cr4 to contain the result of the
comparison between the state the CPU has woken up from and the first
deep stop state before calling pnv_wakeup_tb_loss().
Thus if the CPU woke up from a state that is deeper than the first
deep stop state, cr4 will have "gt" set and hence, pnv_wakeup_tb_loss()
will fail to restore the SPRs on waking up from such a state.
Fix the code in pnv_wakeup_tb_loss() to restore the SPR states when cr4
is "eq" or "gt".
Fixes: bcef83a00d ("powerpc/powernv: Add platform support for stop instruction")
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Reviewed-by: Shreyas B. Prabhu <shreyasbp@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
hmi.c functions are unused unless sibling_subcore_state is nonzero, and
that in turn happens only if KVM is in use. So move the code to
arch/powerpc/kvm/, putting it under CONFIG_KVM_BOOK3S_HV_POSSIBLE
rather than CONFIG_PPC_BOOK3S_64. The sibling_subcore_state is also
included in struct paca_struct only if KVM is supported by the kernel.
Cc: Daniel Axtens <dja@axtens.net>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: kvm-ppc@vger.kernel.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Userspace can begin and suspend a transaction within the signal
handler which means they might enter sys_rt_sigreturn() with the
processor in suspended state.
sys_rt_sigreturn() wants to restore process context (which may have
been in a transaction before signal delivery). To do this it must
restore TM SPRS. To achieve this, any transaction initiated within the
signal frame must be discarded in order to be able to restore TM SPRs
as TM SPRs can only be manipulated non-transactionally..
>From the PowerPC ISA:
TM Bad Thing Exception [Category: Transactional Memory]
An attempt is made to execute a mtspr targeting a TM register in
other than Non-transactional state.
Not doing so results in a TM Bad Thing:
[12045.221359] Kernel BUG at c000000000050a40 [verbose debug info unavailable]
[12045.221470] Unexpected TM Bad Thing exception at c000000000050a40 (msr 0x201033)
[12045.221540] Oops: Unrecoverable exception, sig: 6 [#1]
[12045.221586] SMP NR_CPUS=2048 NUMA PowerNV
[12045.221634] Modules linked in: xt_CHECKSUM iptable_mangle ipt_MASQUERADE
nf_nat_masquerade_ipv4 iptable_nat nf_nat_ipv4 nf_nat nf_conntrack_ipv4 nf_defrag_ipv4
xt_conntrack nf_conntrack ipt_REJECT nf_reject_ipv4 xt_tcpudp bridge stp llc ebtable_filter
ebtables ip6table_filter ip6_tables iptable_filter ip_tables x_tables kvm_hv kvm
uio_pdrv_genirq ipmi_powernv uio powernv_rng ipmi_msghandler autofs4 ses enclosure
scsi_transport_sas bnx2x ipr mdio libcrc32c
[12045.222167] CPU: 68 PID: 6178 Comm: sigreturnpanic Not tainted 4.7.0 #34
[12045.222224] task: c0000000fce38600 ti: c0000000fceb4000 task.ti: c0000000fceb4000
[12045.222293] NIP: c000000000050a40 LR: c0000000000163bc CTR: 0000000000000000
[12045.222361] REGS: c0000000fceb7ac0 TRAP: 0700 Not tainted (4.7.0)
[12045.222418] MSR: 9000000300201033 <SF,HV,ME,IR,DR,RI,LE,TM[SE]> CR: 28444280 XER: 20000000
[12045.222625] CFAR: c0000000000163b8 SOFTE: 0 PACATMSCRATCH: 900000014280f033
GPR00: 01100000b8000001 c0000000fceb7d40 c00000000139c100 c0000000fce390d0
GPR04: 900000034280f033 0000000000000000 0000000000000000 0000000000000000
GPR08: 0000000000000000 b000000000001033 0000000000000001 0000000000000000
GPR12: 0000000000000000 c000000002926400 0000000000000000 0000000000000000
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR24: 0000000000000000 00003ffff98cadd0 00003ffff98cb470 0000000000000000
GPR28: 900000034280f033 c0000000fceb7ea0 0000000000000001 c0000000fce390d0
[12045.223535] NIP [c000000000050a40] tm_restore_sprs+0xc/0x1c
[12045.223584] LR [c0000000000163bc] tm_recheckpoint+0x5c/0xa0
[12045.223630] Call Trace:
[12045.223655] [c0000000fceb7d80] [c000000000026e74] sys_rt_sigreturn+0x494/0x6c0
[12045.223738] [c0000000fceb7e30] [c0000000000092e0] system_call+0x38/0x108
[12045.223806] Instruction dump:
[12045.223841] 7c800164 4e800020 7c0022a6 f80304a8 7c0222a6 f80304b0 7c0122a6 f80304b8
[12045.223955] 4e800020 e80304a8 7c0023a6 e80304b0 <7c0223a6> e80304b8 7c0123a6 4e800020
[12045.224074] ---[ end trace cb8002ee240bae76 ]---
It isn't clear exactly if there is really a use case for userspace
returning with a suspended transaction, however, doing so doesn't (on
its own) constitute a bad frame. As such, this patch simply discards
the transactional state of the context calling the sigreturn and
continues.
Reported-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Tested-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Reviewed-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Acked-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
tabort_syscall runs with RI=1, so a nested recoverable machine
check will load the paca into r13 and overwrite what we loaded
it with, because exceptions returning to privileged mode do not
restore r13.
Fixes: b4b56f9eca (powerpc/tm: Abort syscalls in active transactions)
Cc: stable@vger.kernel.org
Signed-off-by: Nick Piggin <npiggin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Storing this value will help prevent unwinders from getting out of sync
with the function graph tracer ret_stack. Now instead of needing a
stateful iterator, they can compare the return address pointer to find
the right ret_stack entry.
Note that an array of 50 ftrace_ret_stack structs is allocated for every
task. So when an arch implements this, it will add either 200 or 400
bytes of memory usage per task (depending on whether it's a 32-bit or
64-bit platform).
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Byungchul Park <byungchul.park@lge.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nilay Vaish <nilayvaish@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/a95cfcc39e8f26b89a430c56926af0bb217bc0a1.1471607358.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
hmi.c functions are unused unless sibling_subcore_state is nonzero, and
that in turn happens only if KVM is in use. So move the code to
arch/powerpc/kvm/, putting it under CONFIG_KVM_BOOK3S_HV_POSSIBLE
rather than CONFIG_PPC_BOOK3S_64. The sibling_subcore_state is also
included in struct paca_struct only if KVM is supported by the kernel.
Cc: Daniel Axtens <dja@axtens.net>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: kvm-ppc@vger.kernel.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
MCE must not use PACA_EXGEN. When a general exception enables MSR_RI,
that means SPRN_SRR[01] and SPRN_SPRG are no longer used. However the
PACA save area is still in use.
Acked-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When booting from an OpenFirmware which supports it, we use the
"ibm,client-architecture-support" firmware call to communicate
our capabilities to firmware.
The format of the structure we pass to firmware is specified in
PAPR (Power Architecture Platform Requirements), or the public version
LoPAPR (Linux on Power Architecture Platform Reference).
Referring to table 244 in LoPAPR v1.1, option vector 5 contains a 4 byte
field at bytes 17-20 for the "Platform Facilities Enable". This is
followed by a 1 byte field at byte 21 for "Sub-Processor Represenation
Level".
Comparing to the code, there we have the Platform Facilities
options (OV5_PFO_*) at byte 17, but we fail to pad that field out to its
full width of 4 bytes. This means the OV5_SUB_PROCESSORS option is
incorrectly placed at byte 18.
Fix it by adding zero bytes for bytes 18, 19, 20, and comment the bytes
to hopefully make it clearer in future.
As far as I'm aware nothing actually consumes this value at this time,
so the effect of this bug is nil in practice.
It does mean we've been incorrectly setting bit 15 of the "Platform
Facilities Enable" option for the past ~3 1/2 years, so we should avoid
allocating that bit to anything else in future.
Fixes: df77c79920 ("powerpc/pseries: Update ibm,architecture.vec for PAPR 2.7/POWER8")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We observed a kernel oops when running a PPC guest with config NR_CPUS=4
and qemu option "-smp cores=1,threads=8":
[ 30.634781] Unable to handle kernel paging request for data at
address 0xc00000014192eb17
[ 30.636173] Faulting instruction address: 0xc00000000003e5cc
[ 30.637069] Oops: Kernel access of bad area, sig: 11 [#1]
[ 30.637877] SMP NR_CPUS=4 NUMA pSeries
[ 30.638471] Modules linked in:
[ 30.638949] CPU: 3 PID: 27 Comm: migration/3 Not tainted
4.7.0-07963-g9714b26 #1
[ 30.640059] task: c00000001e29c600 task.stack: c00000001e2a8000
[ 30.640956] NIP: c00000000003e5cc LR: c00000000003e550 CTR:
0000000000000000
[ 30.642001] REGS: c00000001e2ab8e0 TRAP: 0300 Not tainted
(4.7.0-07963-g9714b26)
[ 30.643139] MSR: 8000000102803033 <SF,VEC,VSX,FP,ME,IR,DR,RI,LE,TM[E]> CR: 22004084 XER: 00000000
[ 30.644583] CFAR: c000000000009e98 DAR: c00000014192eb17 DSISR: 40000000 SOFTE: 0
GPR00: c00000000140a6b8 c00000001e2abb60 c0000000016dd300 0000000000000003
GPR04: 0000000000000000 0000000000000004 c0000000016e5920 0000000000000008
GPR08: 0000000000000004 c00000014192eb17 0000000000000000 0000000000000020
GPR12: c00000000140a6c0 c00000000ffffc00 c0000000000d3ea8 c00000001e005680
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20: 0000000000000000 c00000001e6b3a00 0000000000000000 0000000000000001
GPR24: c00000001ff85138 c00000001ff85130 000000001eb6f000 0000000000000001
GPR28: 0000000000000000 c0000000017014e0 0000000000000000 0000000000000018
[ 30.653882] NIP [c00000000003e5cc] __cpu_disable+0xcc/0x190
[ 30.654713] LR [c00000000003e550] __cpu_disable+0x50/0x190
[ 30.655528] Call Trace:
[ 30.655893] [c00000001e2abb60] [c00000000003e550] __cpu_disable+0x50/0x190 (unreliable)
[ 30.657280] [c00000001e2abbb0] [c0000000000aca0c] take_cpu_down+0x5c/0x100
[ 30.658365] [c00000001e2abc10] [c000000000163918] multi_cpu_stop+0x1a8/0x1e0
[ 30.659617] [c00000001e2abc60] [c000000000163cc0] cpu_stopper_thread+0xf0/0x1d0
[ 30.660737] [c00000001e2abd20] [c0000000000d8d70] smpboot_thread_fn+0x290/0x2a0
[ 30.661879] [c00000001e2abd80] [c0000000000d3fa8] kthread+0x108/0x130
[ 30.662876] [c00000001e2abe30] [c000000000009968] ret_from_kernel_thread+0x5c/0x74
[ 30.664017] Instruction dump:
[ 30.664477] 7bde1f24 38a00000 787f1f24 3b600001 39890008 7d204b78 7d05e214 7d0b07b4
[ 30.665642] 796b1f24 7d26582a 7d204a14 7d29f214 <7d4048a8> 7d4a3878 7d4049ad 40c2fff4
[ 30.666854] ---[ end trace 32643b7195717741 ]---
The reason of this is that in __cpu_disable(), when we try to set the
cpu_sibling_mask or cpu_core_mask of the sibling CPUs of the disabled
one, we don't check whether the current configuration employs those
sibling CPUs(hw threads). And if a CPU is not employed by a
configuration, the percpu structures cpu_{sibling,core}_mask are not
allocated, therefore accessing those cpumasks will result in problems as
above.
This patch fixes this problem by adding an addition check on whether the
id is no less than nr_cpu_ids in the sibling CPU iteration code.
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These files were only including module.h for exception table
related functions. We've now separated that content out into its
own file "extable.h" so now move over to that and avoid all the
extra header content in module.h that we don't really need to compile
these files.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch leverages 'struct pci_host_bridge' from the PCI subsystem
in order to free the pci_controller only after the last reference to
its devices is dropped (avoiding an oops in pcibios_release_device()
if the last reference is dropped after pcibios_free_controller()).
The patch relies on pci_host_bridge.release_fn() (and .release_data),
which is called automatically by the PCI subsystem when the root bus
is released (i.e., the last reference is dropped). Those fields are
set via pci_set_host_bridge_release() (e.g. in the platform-specific
implementation of pcibios_root_bridge_prepare()).
It introduces the 'pcibios_free_controller_deferred()' .release_fn()
and it expects .release_data to hold a pointer to the pci_controller.
The function implictly calls 'pcibios_free_controller()', so an user
must *NOT* explicitly call it if using the new _deferred() callback.
The functionality is enabled for pseries (although it isn't platform
specific, and may be used by cxl).
Details on not-so-elegant design choices:
- Use 'pci_host_bridge.release_data' field as pointer to associated
'struct pci_controller' so *not* to 'pci_bus_to_host(bridge->bus)'
in pcibios_free_controller_deferred().
That's because pci_remove_root_bus() sets 'host_bridge->bus = NULL'
(so, if the last reference is released after pci_remove_root_bus()
runs, which eventually reaches pcibios_free_controller_deferred(),
that would hit a null pointer dereference).
The cxl/vphb.c code calls pci_remove_root_bus(), and the cxl folks
are interested in this fix.
Test-case #1 (hold references)
# ls -ld /sys/block/sd* | grep -m1 0021:01:00.0
<...> /sys/block/sdaa -> ../devices/pci0021:01/0021:01:00.0/<...>
# ls -ld /sys/block/sd* | grep -m1 0021:01:00.1
<...> /sys/block/sdab -> ../devices/pci0021:01/0021:01:00.1/<...>
# cat >/dev/sdaa & pid1=$!
# cat >/dev/sdab & pid2=$!
# drmgr -w 5 -d 1 -c phb -s 'PHB 33' -r
Validating PHB DLPAR capability...yes.
[ 594.306719] pci_hp_remove_devices: PCI: Removing devices on bus 0021:01
[ 594.306738] pci_hp_remove_devices: Removing 0021:01:00.0...
...
[ 598.236381] pci_hp_remove_devices: Removing 0021:01:00.1...
...
[ 611.972077] pci_bus 0021:01: busn_res: [bus 01-ff] is released
[ 611.972140] rpadlpar_io: slot PHB 33 removed
# kill -9 $pid1
# kill -9 $pid2
[ 632.918088] pcibios_free_controller_deferred: domain 33, dynamic 1
Test-case #2 (don't hold references)
# drmgr -w 5 -d 1 -c phb -s 'PHB 33' -r
Validating PHB DLPAR capability...yes.
[ 916.357363] pci_hp_remove_devices: PCI: Removing devices on bus 0021:01
[ 916.357386] pci_hp_remove_devices: Removing 0021:01:00.0...
...
[ 920.566527] pci_hp_remove_devices: Removing 0021:01:00.1...
...
[ 933.955873] pci_bus 0021:01: busn_res: [bus 01-ff] is released
[ 933.955977] pcibios_free_controller_deferred: domain 33, dynamic 1
[ 933.955999] rpadlpar_io: slot PHB 33 removed
Suggested-By: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Tested-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com> # cxl
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When using if_changed, we need to add FORCE as a dependency (see
Documentation/kbuild/makefiles.txt) otherwise we don't get command line
change checking amongst other things. This has resulted in vdsos not
being rebuilt when switching between big and little endian.
The vdso64/32ld commands have to be changed around to avoid pulling
FORCE into the linker command line (code copied from x86).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We cannot do those initializations from apply_feature_fixups() as
this function runs in a very restricted environment on 32-bit where
the kernel isn't running at its linked address and the PTRRELOC()
macro must be used for any global accesss.
Instead, split them into a separtate steup_feature_keys() function
which is called in a more suitable spot on ppc32.
Fixes: 309b315b6e ("powerpc: Call jump_label_init() in apply_feature_fixups()")
Reported-and-tested-by: Christian Kujau <lists@nerdbynature.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We don't identify the machine type anymore...
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This makes it easier to debug crashes that happen very early before
the kernel takes over Open Firmware by allowing us to relate the OF
reported crashing addresses to offsets within the kernel.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 8d460f6156 ("powerpc/process: Add the function
flush_tmregs_to_thread") added flush_tmregs_to_thread() and included
the assumption that it would only be called for a task which is not
current.
Although this is correct for ptrace, when generating a core dump, some
of the routines which call flush_tmregs_to_thread() are called. This
leads to a WARNing such as:
Not expecting ptrace on self: TM regs may be incorrect
------------[ cut here ]------------
WARNING: CPU: 123 PID: 7727 at arch/powerpc/kernel/process.c:1088 flush_tmregs_to_thread+0x78/0x80
CPU: 123 PID: 7727 Comm: libvirtd Not tainted 4.8.0-rc1-gcc6x-g61e8a0d #1
task: c000000fe631b600 task.stack: c000000fe63b0000
NIP: c00000000001a1a8 LR: c00000000001a1a4 CTR: c000000000717780
REGS: c000000fe63b3420 TRAP: 0700 Not tainted (4.8.0-rc1-gcc6x-g61e8a0d)
MSR: 900000010282b033 <SF,HV,VEC,VSX,EE,FP,ME,IR,DR,RI,LE,TM[E]> CR: 28004222 XER: 20000000
...
NIP [c00000000001a1a8] flush_tmregs_to_thread+0x78/0x80
LR [c00000000001a1a4] flush_tmregs_to_thread+0x74/0x80
Call Trace:
flush_tmregs_to_thread+0x74/0x80 (unreliable)
vsr_get+0x64/0x1a0
elf_core_dump+0x604/0x1430
do_coredump+0x5fc/0x1200
get_signal+0x398/0x740
do_signal+0x54/0x2b0
do_notify_resume+0x98/0xb0
ret_from_except_lite+0x70/0x74
So fix flush_tmregs_to_thread() to detect the case where it is called on
current, and a transaction is active, and in that case flush the TM regs
to the thread_struct.
This patch also moves flush_tmregs_to_thread() into ptrace.c as it is
only called from that file.
Fixes: 8d460f6156 ("powerpc/process: Add the function flush_tmregs_to_thread")
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
[mpe: Flesh out change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When machine check occurs with MSR(RI=0), it means MC interrupt is
unrecoverable and kernel goes down to panic path. But the console
message still shows it as recovered. This patch fixes the MCE console
messages.
Fixes: 36df96f8ac ("powerpc/book3s: Decode and save machine check event.")
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The recent commit 63a72284b1 ("powerpc/pci: Assign fixed PHB number
based on device-tree properties"), added code to read a 64-bit property
from the device tree, and if not found read a 32-bit property (reg).
There was a bug in the 32-bit case, on big endian machines, due to the
use of the 64-bit value to read the 32-bit property. The cast of &prop
means we end up writing to the high 32-bit of prop, leaving the low
32-bits containing whatever junk was on the stack.
If that junk value was non-zero, and < MAX_PHBS, we would end up using
it as the PHB id. This results in users seeing what appear to be random
PHB ids.
Fix it by reading into a u32 property and then assigning that to the
u64 value, letting the CPU do the correct conversions for us.
Fixes: 63a72284b1 ("powerpc/pci: Assign fixed PHB number based on device-tree properties")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This is a very minor/trivial fix for the output of PCI address on EEH
logs. The PCI address on "OF node" field currently is using ":" as a
separator for the function, but the usual separator is ".". This patch
changes the separator to dot, so the PCI address is printed as usual.
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Some powerpc builds fail with the following buld error.
In file included from ./arch/powerpc/include/asm/mmu_context.h:11:0,
from arch/powerpc/kernel/vdso.c:28:
arch/powerpc/include/asm/cputhreads.h: In function 'get_tensr':
arch/powerpc/include/asm/cputhreads.h:101:2: error:
implicit declaration of function 'cpu_has_feature'
Fixes: b92a226e52 ("powerpc: Move cpu_has_feature() to a separate file")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The current implementation of MCE early handling modifies CR0/1 registers
without saving its old values. Fix this by moving early check for
powersaving mode to machine_check_handle_early().
The power architecture 2.06 or later allows the possibility of getting
machine check while in nap/sleep/winkle. The last bit of HSPRG0 is set
to 1, if thread is woken up from winkle. Hence, clear the last bit of
HSPRG0 (r13) before MCE handler starts using it as paca pointer.
Also, the current code always puts the thread into nap state irrespective
of whatever idle state it woke up from. Fix that by looking at
paca->thread_idle_state and put the thread back into same state where it
came from.
Fixes: 1c51089f77 ("powerpc/book3s: Return from interrupt if coming from evil context.")
Reported-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Reviewed-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move IDLE_STATE_ENTER_SEQ macro to cpuidle.h so that MCE handler changes
in subsequent patch can use it.
No functionality change.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The function pnv_restore_hyp_resource() loads the TOC into r2 from
the invalid PACA pointer before fixing r13 value. This do not affect
POWER ISA 3.0 but it does have an impact on POWER ISA 2.07 or less
leading CPU to get stuck forever.
login: [ 471.830433] Processor 120 is stuck.
This can be easily reproducible using following steps:
- Turn off SMT
$ ppc64_cpu --smt=off
- offline/online any online cpu (Thread 0 of any core which is online)
$ echo 0 > /sys/devices/system/cpu/cpu<num>/online
$ echo 1 > /sys/devices/system/cpu/cpu<num>/online
For POWER ISA 2.07 or less, the last bit of HSPRG0 is set indicating
that thread is waking up from winkle. Hence, the last bit of HSPRG0(r13)
needs to be clear before accessing it as PACA to avoid loading invalid
values from invalid PACA pointer.
Fix this by loading TOC after r13 register is corrected.
Fixes: bcef83a00d ("powerpc/powernv: Add platform support for stop instruction")
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Acked-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Cleanups:
- huge cleanup of rtc-generic and char/genrtc this allowed to cleanup rtc-cmos,
rtc-sh, rtc-m68k, rtc-powerpc and rtc-parisc
- move mn10300 to rtc-cmos
Subsystem:
- fix wakealarms after hibernate
- multiples fixes for rctest
- simplify implementations of .read_alarm
New drivers:
- Maxim MAX6916
Drivers:
- ds1307: fix weekday
- m41t80: add wakeup support
- pcf85063: add support for PCF85063A variant
- rv8803: extend i2c fix and other fixes
- s35390a: fix alarm reading, this fixes instant reboot after shutdown for QNAP
TS-41x
- s3c: clock fixes
-----BEGIN PGP SIGNATURE-----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=rpGB
-----END PGP SIGNATURE-----
Merge tag 'rtc-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"RTC for 4.8
Cleanups:
- huge cleanup of rtc-generic and char/genrtc this allowed to cleanup
rtc-cmos, rtc-sh, rtc-m68k, rtc-powerpc and rtc-parisc
- move mn10300 to rtc-cmos
Subsystem:
- fix wakealarms after hibernate
- multiples fixes for rctest
- simplify implementations of .read_alarm
New drivers:
- Maxim MAX6916
Drivers:
- ds1307: fix weekday
- m41t80: add wakeup support
- pcf85063: add support for PCF85063A variant
- rv8803: extend i2c fix and other fixes
- s35390a: fix alarm reading, this fixes instant reboot after
shutdown for QNAP TS-41x
- s3c: clock fixes"
* tag 'rtc-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (65 commits)
rtc: rv8803: Clear V1F when setting the time
rtc: rv8803: Stop the clock while setting the time
rtc: rv8803: Always apply the I²C workaround
rtc: rv8803: Fix read day of week
rtc: rv8803: Remove the check for valid time
rtc: rv8803: Kconfig: Indicate rx8900 support
rtc: asm9260: remove .owner field for driver
rtc: at91sam9: Fix missing spin_lock_init()
rtc: m41t80: add suspend handlers for alarm IRQ
rtc: m41t80: make it a real error message
rtc: pcf85063: Add support for the PCF85063A device
rtc: pcf85063: fix year range
rtc: hym8563: in .read_alarm set .tm_sec to 0 to signal minute accuracy
rtc: explicitly set tm_sec = 0 for drivers with minute accurancy
rtc: s3c: Add s3c_rtc_{enable/disable}_clk in s3c_rtc_setfreq()
rtc: s3c: Remove unnecessary call to disable already disabled clock
rtc: abx80x: use devm_add_action_or_reset()
rtc: m41t80: use devm_add_action_or_reset()
rtc: fix a typo and reduce three empty lines to one
rtc: s35390a: improve two comments in .set_alarm
...
Fixes:
- Fix early access to cpu_spec relocation from Benjamin Herrenschmidt
- Fix incorrect event codes in power9-event-list from Madhavan Srinivasan
- Move register_process_table() out of ppc_md from Michael Ellerman
Use jump_label for [cpu|mmu]_has_feature() from Aneesh Kumar K.V, Kevin Hao and Michael Ellerman:
- Add mmu_early_init_devtree() from Michael Ellerman
- Move disable_radix handling into mmu_early_init_devtree() from Michael Ellerman
- Do hash device tree scanning earlier from Michael Ellerman
- Do radix device tree scanning earlier from Michael Ellerman
- Do feature patching before MMU init from Michael Ellerman
- Check features don't change after patching from Michael Ellerman
- Make MMU_FTR_RADIX a MMU family feature from Aneesh Kumar K.V
- Convert mmu_has_feature() to returning bool from Michael Ellerman
- Convert cpu_has_feature() to returning bool from Michael Ellerman
- Define radix_enabled() in one place & use static inline from Michael Ellerman
- Add early_[cpu|mmu]_has_feature() from Michael Ellerman
- Convert early cpu/mmu feature check to use the new helpers from Aneesh Kumar K.V
- jump_label: Make it possible for arches to invoke jump_label_init() earlier from Kevin Hao
- Call jump_label_init() in apply_feature_fixups() from Aneesh Kumar K.V
- Remove mfvtb() from Kevin Hao
- Move cpu_has_feature() to a separate file from Kevin Hao
- Add kconfig option to use jump labels for cpu/mmu_has_feature() from Michael Ellerman
- Add option to use jump label for cpu_has_feature() from Kevin Hao
- Add option to use jump label for mmu_has_feature() from Kevin Hao
- Catch usage of cpu/mmu_has_feature() before jump label init from Aneesh Kumar K.V
- Annotate jump label assembly from Michael Ellerman
TLB flush enhancements from Aneesh Kumar K.V:
- radix: Implement tlb mmu gather flush efficiently
- Add helper for finding SLBE LLP encoding
- Use hugetlb flush functions
- Drop multiple definition of mm_is_core_local
- radix: Add tlb flush of THP ptes
- radix: Rename function and drop unused arg
- radix/hugetlb: Add helper for finding page size
- hugetlb: Add flush_hugetlb_tlb_range
- remove flush_tlb_page_nohash
Add new ptrace regsets from Anshuman Khandual and Simon Guo:
- elf: Add powerpc specific core note sections
- Add the function flush_tmregs_to_thread
- Enable in transaction NT_PRFPREG ptrace requests
- Enable in transaction NT_PPC_VMX ptrace requests
- Enable in transaction NT_PPC_VSX ptrace requests
- Adapt gpr32_get, gpr32_set functions for transaction
- Enable support for NT_PPC_CGPR
- Enable support for NT_PPC_CFPR
- Enable support for NT_PPC_CVMX
- Enable support for NT_PPC_CVSX
- Enable support for TM SPR state
- Enable NT_PPC_TM_CTAR, NT_PPC_TM_CPPR, NT_PPC_TM_CDSCR
- Enable support for NT_PPPC_TAR, NT_PPC_PPR, NT_PPC_DSCR
- Enable support for EBB registers
- Enable support for Performance Monitor registers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0Q8E
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull more powerpc updates from Michael Ellerman:
"These were delayed for various reasons, so I let them sit in next a
bit longer, rather than including them in my first pull request.
Fixes:
- Fix early access to cpu_spec relocation from Benjamin Herrenschmidt
- Fix incorrect event codes in power9-event-list from Madhavan Srinivasan
- Move register_process_table() out of ppc_md from Michael Ellerman
Use jump_label use for [cpu|mmu]_has_feature():
- Add mmu_early_init_devtree() from Michael Ellerman
- Move disable_radix handling into mmu_early_init_devtree() from Michael Ellerman
- Do hash device tree scanning earlier from Michael Ellerman
- Do radix device tree scanning earlier from Michael Ellerman
- Do feature patching before MMU init from Michael Ellerman
- Check features don't change after patching from Michael Ellerman
- Make MMU_FTR_RADIX a MMU family feature from Aneesh Kumar K.V
- Convert mmu_has_feature() to returning bool from Michael Ellerman
- Convert cpu_has_feature() to returning bool from Michael Ellerman
- Define radix_enabled() in one place & use static inline from Michael Ellerman
- Add early_[cpu|mmu]_has_feature() from Michael Ellerman
- Convert early cpu/mmu feature check to use the new helpers from Aneesh Kumar K.V
- jump_label: Make it possible for arches to invoke jump_label_init() earlier from Kevin Hao
- Call jump_label_init() in apply_feature_fixups() from Aneesh Kumar K.V
- Remove mfvtb() from Kevin Hao
- Move cpu_has_feature() to a separate file from Kevin Hao
- Add kconfig option to use jump labels for cpu/mmu_has_feature() from Michael Ellerman
- Add option to use jump label for cpu_has_feature() from Kevin Hao
- Add option to use jump label for mmu_has_feature() from Kevin Hao
- Catch usage of cpu/mmu_has_feature() before jump label init from Aneesh Kumar K.V
- Annotate jump label assembly from Michael Ellerman
TLB flush enhancements from Aneesh Kumar K.V:
- radix: Implement tlb mmu gather flush efficiently
- Add helper for finding SLBE LLP encoding
- Use hugetlb flush functions
- Drop multiple definition of mm_is_core_local
- radix: Add tlb flush of THP ptes
- radix: Rename function and drop unused arg
- radix/hugetlb: Add helper for finding page size
- hugetlb: Add flush_hugetlb_tlb_range
- remove flush_tlb_page_nohash
Add new ptrace regsets from Anshuman Khandual and Simon Guo:
- elf: Add powerpc specific core note sections
- Add the function flush_tmregs_to_thread
- Enable in transaction NT_PRFPREG ptrace requests
- Enable in transaction NT_PPC_VMX ptrace requests
- Enable in transaction NT_PPC_VSX ptrace requests
- Adapt gpr32_get, gpr32_set functions for transaction
- Enable support for NT_PPC_CGPR
- Enable support for NT_PPC_CFPR
- Enable support for NT_PPC_CVMX
- Enable support for NT_PPC_CVSX
- Enable support for TM SPR state
- Enable NT_PPC_TM_CTAR, NT_PPC_TM_CPPR, NT_PPC_TM_CDSCR
- Enable support for NT_PPPC_TAR, NT_PPC_PPR, NT_PPC_DSCR
- Enable support for EBB registers
- Enable support for Performance Monitor registers"
* tag 'powerpc-4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (48 commits)
powerpc/mm: Move register_process_table() out of ppc_md
powerpc/perf: Fix incorrect event codes in power9-event-list
powerpc/32: Fix early access to cpu_spec relocation
powerpc/ptrace: Enable support for Performance Monitor registers
powerpc/ptrace: Enable support for EBB registers
powerpc/ptrace: Enable support for NT_PPPC_TAR, NT_PPC_PPR, NT_PPC_DSCR
powerpc/ptrace: Enable NT_PPC_TM_CTAR, NT_PPC_TM_CPPR, NT_PPC_TM_CDSCR
powerpc/ptrace: Enable support for TM SPR state
powerpc/ptrace: Enable support for NT_PPC_CVSX
powerpc/ptrace: Enable support for NT_PPC_CVMX
powerpc/ptrace: Enable support for NT_PPC_CFPR
powerpc/ptrace: Enable support for NT_PPC_CGPR
powerpc/ptrace: Adapt gpr32_get, gpr32_set functions for transaction
powerpc/ptrace: Enable in transaction NT_PPC_VSX ptrace requests
powerpc/ptrace: Enable in transaction NT_PPC_VMX ptrace requests
powerpc/ptrace: Enable in transaction NT_PRFPREG ptrace requests
powerpc/process: Add the function flush_tmregs_to_thread
elf: Add powerpc specific core note sections
powerpc/mm: remove flush_tlb_page_nohash
powerpc/mm/hugetlb: Add flush_hugetlb_tlb_range
...
The dma-mapping core and the implementations do not change the DMA
attributes passed by pointer. Thus the pointer can point to const data.
However the attributes do not have to be a bitfield. Instead unsigned
long will do fine:
1. This is just simpler. Both in terms of reading the code and setting
attributes. Instead of initializing local attributes on the stack
and passing pointer to it to dma_set_attr(), just set the bits.
2. It brings safeness and checking for const correctness because the
attributes are passed by value.
Semantic patches for this change (at least most of them):
virtual patch
virtual context
@r@
identifier f, attrs;
@@
f(...,
- struct dma_attrs *attrs
+ unsigned long attrs
, ...)
{
...
}
@@
identifier r.f;
@@
f(...,
- NULL
+ 0
)
and
// Options: --all-includes
virtual patch
virtual context
@r@
identifier f, attrs;
type t;
@@
t f(..., struct dma_attrs *attrs);
@@
identifier r.f;
@@
f(...,
- NULL
+ 0
)
Link: http://lkml.kernel.org/r/1468399300-5399-2-git-send-email-k.kozlowski@samsung.com
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Acked-by: Mark Salter <msalter@redhat.com> [c6x]
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com> [cris]
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> [drm]
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Fabien Dessenne <fabien.dessenne@st.com> [bdisp]
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com> [vb2-core]
Acked-by: David Vrabel <david.vrabel@citrix.com> [xen]
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> [xen swiotlb]
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Richard Kuo <rkuo@codeaurora.org> [hexagon]
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Acked-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> [s390]
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no> [avr32]
Acked-by: Vineet Gupta <vgupta@synopsys.com> [arc]
Acked-by: Robin Murphy <robin.murphy@arm.com> [arm64 and dma-iommu]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
VGIC implementation.
- s390: support for trapping software breakpoints, nested virtualization
(vSIE), the STHYI opcode, initial extensions for CPU model support.
- MIPS: support for MIPS64 hosts (32-bit guests only) and lots of cleanups,
preliminary to this and the upcoming support for hardware virtualization
extensions.
- x86: support for execute-only mappings in nested EPT; reduced vmexit
latency for TSC deadline timer (by about 30%) on Intel hosts; support for
more than 255 vCPUs.
- PPC: bugfixes.
The ugly bit is the conflicts. A couple of them are simple conflicts due
to 4.7 fixes, but most of them are with other trees. There was definitely
too much reliance on Acked-by here. Some conflicts are for KVM patches
where _I_ gave my Acked-by, but the worst are for this pull request's
patches that touch files outside arch/*/kvm. KVM submaintainers should
probably learn to synchronize better with arch maintainers, with the
latter providing topic branches whenever possible instead of Acked-by.
This is what we do with arch/x86. And I should learn to refuse pull
requests when linux-next sends scary signals, even if that means that
submaintainers have to rebase their branches.
Anyhow, here's the list:
- arch/x86/kvm/vmx.c: handle_pcommit and EXIT_REASON_PCOMMIT was removed
by the nvdimm tree. This tree adds handle_preemption_timer and
EXIT_REASON_PREEMPTION_TIMER at the same place. In general all mentions
of pcommit have to go.
There is also a conflict between a stable fix and this patch, where the
stable fix removed the vmx_create_pml_buffer function and its call.
- virt/kvm/kvm_main.c: kvm_cpu_notifier was removed by the hotplug tree.
This tree adds kvm_io_bus_get_dev at the same place.
- virt/kvm/arm/vgic.c: a few final bugfixes went into 4.7 before the
file was completely removed for 4.8.
- include/linux/irqchip/arm-gic-v3.h: this one is entirely our fault;
this is a change that should have gone in through the irqchip tree and
pulled by kvm-arm. I think I would have rejected this kvm-arm pull
request. The KVM version is the right one, except that it lacks
GITS_BASER_PAGES_SHIFT.
- arch/powerpc: what a mess. For the idle_book3s.S conflict, the KVM
tree is the right one; everything else is trivial. In this case I am
not quite sure what went wrong. The commit that is causing the mess
(fd7bacbca4, "KVM: PPC: Book3S HV: Fix TB corruption in guest exit
path on HMI interrupt", 2016-05-15) touches both arch/powerpc/kernel/
and arch/powerpc/kvm/. It's large, but at 396 insertions/5 deletions
I guessed that it wasn't really possible to split it and that the 5
deletions wouldn't conflict. That wasn't the case.
- arch/s390: also messy. First is hypfs_diag.c where the KVM tree
moved some code and the s390 tree patched it. You have to reapply the
relevant part of commits 6c22c98637, plus all of e030c1125e, to
arch/s390/kernel/diag.c. Or pick the linux-next conflict
resolution from http://marc.info/?l=kvm&m=146717549531603&w=2.
Second, there is a conflict in gmap.c between a stable fix and 4.8.
The KVM version here is the correct one.
I have pushed my resolution at refs/heads/merge-20160802 (commit
3d1f53419842) at git://git.kernel.org/pub/scm/virt/kvm/kvm.git.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJXoGm7AAoJEL/70l94x66DugQIAIj703ePAFepB/fCrKHkZZia
SGrsBdvAtNsOhr7FQ5qvvjLxiv/cv7CymeuJivX8H+4kuUHUllDzey+RPHYHD9X7
U6n1PdCH9F15a3IXc8tDjlDdOMNIKJixYuq1UyNZMU6NFwl00+TZf9JF8A2US65b
x/41W98ilL6nNBAsoDVmCLtPNWAqQ3lajaZELGfcqRQ9ZGKcAYOaLFXHv2YHf2XC
qIDMf+slBGSQ66UoATnYV2gAopNlWbZ7n0vO6tE2KyvhHZ1m399aBX1+k8la/0JI
69r+Tz7ZHUSFtmlmyByi5IAB87myy2WQHyAPwj+4vwJkDGPcl0TrupzbG7+T05Y=
=42ti
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
- ARM: GICv3 ITS emulation and various fixes. Removal of the
old VGIC implementation.
- s390: support for trapping software breakpoints, nested
virtualization (vSIE), the STHYI opcode, initial extensions
for CPU model support.
- MIPS: support for MIPS64 hosts (32-bit guests only) and lots
of cleanups, preliminary to this and the upcoming support for
hardware virtualization extensions.
- x86: support for execute-only mappings in nested EPT; reduced
vmexit latency for TSC deadline timer (by about 30%) on Intel
hosts; support for more than 255 vCPUs.
- PPC: bugfixes.
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (302 commits)
KVM: PPC: Introduce KVM_CAP_PPC_HTM
MIPS: Select HAVE_KVM for MIPS64_R{2,6}
MIPS: KVM: Reset CP0_PageMask during host TLB flush
MIPS: KVM: Fix ptr->int cast via KVM_GUEST_KSEGX()
MIPS: KVM: Sign extend MFC0/RDHWR results
MIPS: KVM: Fix 64-bit big endian dynamic translation
MIPS: KVM: Fail if ebase doesn't fit in CP0_EBase
MIPS: KVM: Use 64-bit CP0_EBase when appropriate
MIPS: KVM: Set CP0_Status.KX on MIPS64
MIPS: KVM: Make entry code MIPS64 friendly
MIPS: KVM: Use kmap instead of CKSEG0ADDR()
MIPS: KVM: Use virt_to_phys() to get commpage PFN
MIPS: Fix definition of KSEGX() for 64-bit
KVM: VMX: Add VMCS to CPU's loaded VMCSs before VMPTRLD
kvm: x86: nVMX: maintain internal copy of current VMCS
KVM: PPC: Book3S HV: Save/restore TM state in H_CEDE
KVM: PPC: Book3S HV: Pull out TM state save/restore into separate procedures
KVM: arm64: vgic-its: Simplify MAPI error handling
KVM: arm64: vgic-its: Make vgic_its_cmd_handle_mapi similar to other handlers
KVM: arm64: vgic-its: Turn device_id validation into generic ID validation
...
This patch enables support for Performance monitor registers related
ELF core note NT_PPC_PMU based ptrace requests through
PTRACE_GETREGSET, PTRACE_SETREGSET calls. This is achieved
through adding one new register sets REGSET_PMU in powerpc
corresponding to the ELF core note sections added in this
regard. It also implements the get, set and active functions
for this new register sets added.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables support for EBB state registers related
ELF core note NT_PPC_EBB based ptrace requests through
PTRACE_GETREGSET, PTRACE_SETREGSET calls. This is achieved
through adding one new register sets REGSET_EBB in powerpc
corresponding to the ELF core note sections added in this
regard. It also implements the get, set and active functions
for this new register sets added.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables support for running TAR, PPR, DSCR registers
related ELF core notes NT_PPPC_TAR, NT_PPC_PPR, NT_PPC_DSCR based
ptrace requests through PTRACE_GETREGSET, PTRACE_SETREGSET calls.
This is achieved through adding three new register sets REGSET_TAR,
REGSET_PPR, REGSET_DSCR in powerpc corresponding to the ELF core
note sections added in this regad. It implements the get, set and
active functions for all these new register sets added.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables support for all three TM checkpointed SPR
states related ELF core note NT_PPC_TM_CTAR, NT_PPC_TM_CPPR,
NT_PPC_TM_CDSCR based ptrace requests through PTRACE_GETREGSET,
PTRACE_SETREGSET calls. This is achieved through adding three
new register sets REGSET_TM_CTAR, REGSET_TM_CPPR and
REGSET_TM_CDSCR in powerpc corresponding to the ELF core note
sections added. It implements the get, set and active functions
for all these new register sets added.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables support for TM SPR state related ELF core
note NT_PPC_TM_SPR based ptrace requests through PTRACE_GETREGSET,
PTRACE_SETREGSET calls. This is achieved through adding a register
set REGSET_TM_SPR in powerpc corresponding to the ELF core note
section added. It implements the get, set and active functions for
this new register set added.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables support for TM checkpointed VSX register
set ELF core note NT_PPC_CVSX based ptrace requests through
PTRACE_GETREGSET, PTRACE_SETREGSET calls. This is achieved
through adding a register set REGSET_CVSX in powerpc
corresponding to the ELF core note section added. It
implements the get, set and active functions for this new
register set added.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables support for TM checkpointed VMX register
set ELF core note NT_PPC_CVMX based ptrace requests through
PTRACE_GETREGSET, PTRACE_SETREGSET calls. This is achieved
through adding a register set REGSET_CVMX in powerpc
corresponding to the ELF core note section added. It
implements the get, set and active functions for this new
register set added.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables support for TM checkpointed FPR register
set ELF core note NT_PPC_CFPR based ptrace requests through
PTRACE_GETREGSET, PTRACE_SETREGSET calls. This is achieved
through adding a register set REGSET_CFPR in powerpc
corresponding to the ELF core note section added. It
implements the get, set and active functions for this new
register set added.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables support for TM checkpointed GPR register
set ELF core note NT_PPC_CGPR based ptrace requests through
PTRACE_GETREGSET, PTRACE_SETREGSET calls. This is achieved
through adding a register set REGSET_CGPR in powerpc
corresponding to the ELF core note section added. It
implements the get, set and active functions for this new
register set added.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch splits gpr32_get, gpr32_set functions to accommodate
in transaction ptrace requests implemented in patches later in
the series.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables in transaction NT_PPC_VSX ptrace requests. The
function vsr_get which gets the running value of all VSX registers
and the function vsr_set which sets the running value of of all VSX
registers work on the running set of VMX registers whose location
will be different if transaction is active. This patch makes these
functions adapt to situations when the transaction is active.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables in transaction NT_PPC_VMX ptrace requests. The
function vr_get which gets the running value of all VMX registers
and the function vr_set which sets the running value of of all VMX
registers work on the running set of VMX registers whose location
will be different if transaction is active. This patch makes these
functions adapt to situations when the transaction is active.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables in transaction NT_PRFPREG ptrace requests.
The function fpr_get which gets the running value of all FPR
registers and the function fpr_set which sets the running
value of of all FPR registers work on the running set of FPR
registers whose location will be different if transaction is
active. This patch makes these functions adapt to situations
when the transaction is active.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch creates a function flush_tmregs_to_thread which
will then be used by subsequent patches in this series. The
function checks for self tracing ptrace interface attempts
while in the TM context and logs appropriate warning message.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As we just did for CPU features.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We do binary patching of asm code using CPU features, which is a
one-time operation, done during early boot. However checks of CPU
features in C code are currently done at run time, even though the set
of CPU features can never change after boot.
We can optimise this by using jump labels to implement cpu_has_feature(),
meaning checks in C code are binary patched into a single nop or branch.
For a C sequence along the lines of:
if (cpu_has_feature(FOO))
return 2;
The generated code before is roughly:
ld r9,-27640(r2)
ld r9,0(r9)
lwz r9,32(r9)
cmpwi cr7,r9,0
bge cr7, 1f
li r3,2
blr
1: ...
After (true):
nop
li r3,2
blr
After (false):
b 1f
li r3,2
blr
1: ...
mpe: Rename MAX_CPU_FEATURES as we already have a #define with that
name, and define it simply as a constant, rather than doing tricks with
sizeof and NULL pointers. Rename the array to cpu_feature_keys. Use the
kconfig we added to guard it. Add BUILD_BUG_ON() if the feature is not a
compile time constant. Rewrite the change log.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We plan to use jump label for cpu_has_feature(). In order to implement
this we need to include the linux/jump_label.h in asm/cputable.h.
Unfortunately if we do that it leads to an include loop. The root of the
problem seems to be that reg.h needs cputable.h (for CPU_FTRs), and then
cputable.h via jump_label.h eventually pulls in hw_irq.h which needs
reg.h (for MSR_EE).
So move cpu_has_feature() to a separate file on its own.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[mpe: Rename to cpu_has_feature.h and flesh out change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This switches early feature checks to use the non static key variant of
the function. In later patches we will be switching cpu_has_feature()
and mmu_has_feature() to use static keys and we can use them only after
static key/jump label is initialized. Any check for feature before jump
label init should be done using this new helper.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
MMU feature bits are defined such that we use the lower half to
present MMU family features. Remove the strict split of half and
also move Radix to a mmu family feature. Radix introduce a new MMU
model and strictly speaking it is a new MMU family. This also free
up bits which can be used for individual features later.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Up until now we needed to do the MMU init before feature patching,
because part of the MMU init was scanning the device tree and setting
and/or clearing some MMU feature bits.
Now that we have split that MMU feature modification out into routines
called from early_init_devtree() (called earlier) we can now do feature
patching before calling MMU init.
The advantage of this is it means the remainder of the MMU init runs
with the final set of features which will apply for the rest of the life
of the system. This means we don't have to special case anything called
from MMU init to deal with a changing set of feature bits.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move the handling of the disable_radix command line argument into the
newly created mmu_early_init_devtree().
It's an MMU option so it's preferable to have it in an mm related file,
and it also means platforms that don't support radix don't have to carry
the code.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Highlights:
- PowerNV PCI hotplug support.
- Lots more Power9 support.
- eBPF JIT support on ppc64le.
- Lots of cxl updates.
- Boot code consolidation.
Bug fixes:
- Fix spin_unlock_wait() from Boqun Feng
- Fix stack pointer corruption in __tm_recheckpoint() from Michael Neuling
- Fix multiple bugs in memory_hotplug_max() from Bharata B Rao
- mm: Ensure "special" zones are empty from Oliver O'Halloran
- ftrace: Separate the heuristics for checking call sites from Michael Ellerman
- modules: Never restore r2 for a mprofile-kernel style mcount() call from Michael Ellerman
- Fix endianness when reading TCEs from Alexey Kardashevskiy
- start rtasd before PCI probing from Greg Kurz
- PCI: rpaphp: Fix slot registration for multiple slots under a PHB from Tyrel Datwyler
- powerpc/mm: Add memory barrier in __hugepte_alloc() from Sukadev Bhattiprolu
Cleanups & fixes:
- Drop support for MPIC in pseries from Rashmica Gupta
- Define and use PPC64_ELF_ABI_v2/v1 from Michael Ellerman
- Remove unused symbols in asm-offsets.c from Rashmica Gupta
- Fix SRIOV not building without EEH enabled from Russell Currey
- Remove kretprobe_trampoline_holder. from Thiago Jung Bauermann
- Reduce log level of PCI I/O space warning from Benjamin Herrenschmidt
- Add array bounds checking to crash_shutdown_handlers from Suraj Jitindar Singh
- Avoid -maltivec when using clang integrated assembler from Anton Blanchard
- Fix array overrun in ppc_rtas() syscall from Andrew Donnellan
- Fix error return value in cmm_mem_going_offline() from Rasmus Villemoes
- export cpu_to_core_id() from Mauricio Faria de Oliveira
- Remove old symbols from defconfigs from Andrew Donnellan
- Update obsolete comments in setup_32.c about entry conditions from Benjamin Herrenschmidt
- Add comment explaining the purpose of setup_kdump_trampoline() from Benjamin Herrenschmidt
- Merge the RELOCATABLE config entries for ppc32 and ppc64 from Kevin Hao
- Remove RELOCATABLE_PPC32 from Kevin Hao
- Fix .long's in tlb-radix.c to more meaningful from Balbir Singh
Minor cleanups & fixes:
- Andrew Donnellan, Anna-Maria Gleixner, Anton Blanchard, Benjamin
Herrenschmidt, Bharata B Rao, Christophe Leroy, Colin Ian King, Geliang
Tang, Greg Kurz, Madhavan Srinivasan, Michael Ellerman, Michael Ellerman,
Stephen Rothwell, Stewart Smith.
Freescale updates from Scott:
- "Highlights include more 8xx optimizations, device tree updates,
and MVME7100 support."
PowerNV PCI hotplug from Gavin Shan:
- PCI: Add pcibios_setup_bridge()
- Override pcibios_setup_bridge()
- Remove PCI_RESET_DELAY_US
- Move pnv_pci_ioda_setup_opal_tce_kill() around
- Increase PE# capacity
- Allocate PE# in reverse order
- Create PEs in pcibios_setup_bridge()
- Setup PE for root bus
- Extend PCI bridge resources
- Make pnv_ioda_deconfigure_pe() visible
- Dynamically release PE
- Update bridge windows on PCI plug
- Delay populating pdn
- Support PCI slot ID
- Use PCI slot reset infrastructure
- Introduce pnv_pci_get_slot_id()
- Functions to get/set PCI slot state
- PCI/hotplug: PowerPC PowerNV PCI hotplug driver
- Print correct PHB type names
Power9 idle support from Shreyas B. Prabhu:
- set power_save func after the idle states are initialized
- Use PNV_THREAD_WINKLE macro while requesting for winkle
- make hypervisor state restore a function
- Rename idle_power7.S to idle_book3s.S
- Rename reusable idle functions to hardware agnostic names
- Make pnv_powersave_common more generic
- abstraction for saving SPRs before entering deep idle states
- Add platform support for stop instruction
- cpuidle/powernv: Use CPUIDLE_STATE_MAX instead of MAX_POWERNV_IDLE_STATES
- cpuidle/powernv: cleanup cpuidle-powernv.c
- cpuidle/powernv: Add support for POWER ISA v3 idle states
- Use deepest stop state when cpu is offlined
Power9 PMU from Madhavan Srinivasan:
- factor out power8 pmu macros and defines
- factor out power8 pmu functions
- factor out power8 __init_pmu code
- Add power9 event list macros for generic and cache events
- Power9 PMU support
- Export Power9 generic and cache events to sysfs
Power9 preliminary interrupt & PCI support from Benjamin Herrenschmidt:
- Add XICS emulation APIs
- Move a few exception common handlers to make room
- Add support for HV virtualization interrupts
- Add mechanism to force a replay of interrupts
- Add ICP OPAL backend
- Discover IODA3 PHBs
- pci: Remove obsolete SW invalidate
- opal: Add real mode call wrappers
- Rename TCE invalidation calls
- Remove SWINV constants and obsolete TCE code
- Rework accessing the TCE invalidate register
- Fallback to OPAL for TCE invalidations
- Use the device-tree to get available range of M64's
- Check status of a PHB before using it
- pci: Don't try to allocate resources that will be reassigned
Other Power9:
- Send SIGBUS on unaligned copy and paste from Chris Smart
- Large Decrementer support from Oliver O'Halloran
- Load Monitor Register Support from Jack Miller
Performance improvements from Anton Blanchard:
- Avoid load hit store in __giveup_fpu() and __giveup_altivec()
- Avoid load hit store in setup_sigcontext()
- Remove assembly versions of strcpy, strcat, strlen and strcmp
- Align hot loops of some string functions
eBPF JIT from Naveen N. Rao:
- Fix/enhance 32-bit Load Immediate implementation
- Optimize 64-bit Immediate loads
- Introduce rotate immediate instructions
- A few cleanups
- Isolate classic BPF JIT specifics into a separate header
- Implement JIT compiler for extended BPF
Operator Panel driver from Suraj Jitindar Singh:
- devicetree/bindings: Add binding for operator panel on FSP machines
- Add inline function to get rc from an ASYNC_COMP opal_msg
- Add driver for operator panel on FSP machines
Sparse fixes from Daniel Axtens:
- make some things static
- Introduce asm-prototypes.h
- Include headers containing prototypes
- Use #ifdef __BIG_ENDIAN__ #else for REG_BYTE
- kvm: Clarify __user annotations
- Pass endianness to sparse
- Make ppc_md.{halt, restart} __noreturn
MM fixes & cleanups from Aneesh Kumar K.V:
- radix: Update LPCR HR bit as per ISA
- use _raw variant of page table accessors
- Compile out radix related functions if RADIX_MMU is disabled
- Clear top 16 bits of va only on older cpus
- Print formation regarding the the MMU mode
- hash: Update SDR1 size encoding as documented in ISA 3.0
- radix: Update PID switch sequence
- radix: Update machine call back to support new HCALL.
- radix: Add LPID based tlb flush helpers
- radix: Add a kernel command line to disable radix
- Cleanup LPCR defines
Boot code consolidation from Benjamin Herrenschmidt:
- Move epapr_paravirt_early_init() to early_init_devtree()
- cell: Don't use flat device-tree after boot
- ge_imp3a: Don't use the flat device-tree after boot
- mpc85xx_ds: Don't use the flat device-tree after boot
- mpc85xx_rdb: Don't use the flat device-tree after boot
- Don't test for machine type in rtas_initialize()
- Don't test for machine type in smp_setup_cpu_maps()
- dt: Add of_device_compatible_match()
- Factor do_feature_fixup calls
- Move 64-bit feature fixup earlier
- Move 64-bit memory reserves to setup_arch()
- Use a cachable DART
- Move FW feature probing out of pseries probe()
- Put exception configuration in a common place
- Remove early allocation of the SMU command buffer
- Move MMU backend selection out of platform code
- pasemi: Remove IOBMAP allocation from platform probe()
- mm/hash: Don't use machine_is() early during boot
- Don't test for machine type to detect HEA special case
- pmac: Remove spurrious machine type test
- Move hash table ops to a separate structure
- Ensure that ppc_md is empty before probing for machine type
- Move 64-bit probe_machine() to later in the boot process
- Move 32-bit probe() machine to later in the boot process
- Get rid of ppc_md.init_early()
- Move the boot time info banner to a separate function
- Move setting of {i,d}cache_bsize to initialize_cache_info()
- Move the content of setup_system() to setup_arch()
- Move cache info inits to a separate function
- Re-order the call to smp_setup_cpu_maps()
- Re-order setup_panic()
- Make a few boot functions __init
- Merge 32-bit and 64-bit setup_arch()
Other new features:
- tty/hvc: Use IRQF_SHARED for OPAL hvc consoles from Sam Mendoza-Jonas
- tty/hvc: Use opal irqchip interface if available from Sam Mendoza-Jonas
- powerpc: Add module autoloading based on CPU features from Alastair D'Silva
- crypto: vmx - Convert to CPU feature based module autoloading from Alastair D'Silva
- Wake up kopald polling thread before waiting for events from Benjamin Herrenschmidt
- xmon: Dump ISA 2.06 SPRs from Michael Ellerman
- xmon: Dump ISA 2.07 SPRs from Michael Ellerman
- Add a parameter to disable 1TB segs from Oliver O'Halloran
- powerpc/boot: Add OPAL console to epapr wrappers from Oliver O'Halloran
- Assign fixed PHB number based on device-tree properties from Guilherme G. Piccoli
- pseries: Add pseries hotplug workqueue from John Allen
- pseries: Add support for hotplug interrupt source from John Allen
- pseries: Use kernel hotplug queue for PowerVM hotplug events from John Allen
- pseries: Move property cloning into its own routine from Nathan Fontenot
- pseries: Dynamic add entires to associativity lookup array from Nathan Fontenot
- pseries: Auto-online hotplugged memory from Nathan Fontenot
- pseries: Remove call to memblock_add() from Nathan Fontenot
cxl:
- Add set and get private data to context struct from Michael Neuling
- make base more explicitly non-modular from Paul Gortmaker
- Use for_each_compatible_node() macro from Wei Yongjun
- Frederic Barrat
- Abstract the differences between the PSL and XSL
- Make vPHB device node match adapter's
- Philippe Bergheaud
- Add mechanism for delivering AFU driver specific events
- Ignore CAPI adapters misplaced in switched slots
- Refine slice error debug messages
- Andrew Donnellan
- static-ify variables to fix sparse warnings
- PCI/hotplug: pnv_php: export symbols and move struct types needed by cxl
- PCI/hotplug: pnv_php: handle OPAL_PCI_SLOT_OFFLINE power state
- Add cxl_check_and_switch_mode() API to switch bi-modal cards
- remove dead Kconfig options
- fix potential NULL dereference in free_adapter()
- Ian Munsie
- Update process element after allocating interrupts
- Add support for CAPP DMA mode
- Fix allowing bogus AFU descriptors with 0 maximum processes
- Fix allocating a minimum of 2 pages for the SPA
- Fix bug where AFU disable operation had no effect
- Workaround XSL bug that does not clear the RA bit after a reset
- Fix NULL pointer dereference on kernel contexts with no AFU interrupts
- powerpc/powernv: Split cxl code out into a separate file
- Add cxl_slot_is_supported API
- Enable bus mastering for devices using CAPP DMA mode
- Move cxl_afu_get / cxl_afu_put to base
- Allow a default context to be associated with an external pci_dev
- Do not create vPHB if there are no AFU configuration records
- powerpc/powernv: Add support for the cxl kernel api on the real phb
- Add support for using the kernel API with a real PHB
- Add kernel APIs to get & set the max irqs per context
- Add preliminary workaround for CX4 interrupt limitation
- Add support for interrupts on the Mellanox CX4
- Workaround PE=0 hardware limitation in Mellanox CX4
- powerpc/powernv: Fix pci-cxl.c build when CONFIG_MODULES=n
selftests:
- Test unaligned copy and paste from Chris Smart
- Load Monitor Register Tests from Jack Miller
- Cyril Bur
- exec() with suspended transaction
- Use signed long to read perf_event_paranoid
- Fix usage message in context_switch
- Fix generation of vector instructions/types in context_switch
- Michael Ellerman
- Use "Delta" rather than "Error" in normal output
- Import Anton's mmap & futex micro benchmarks
- Add a test for PROT_SAO
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXnWchAAoJEFHr6jzI4aWAe64P/36Vd9yJLptjkoyZp8/IQtu1
Cv8buQwGdKuSMzdkcUAOXcC3fe2u70ZWXMKKLfY3koIV1IAiqdWk5/XWRKMP2XmE
dG0LhSf0uu7uh+mE0WvQnRu46ImeKtQ+mPp4Hbs/s9SxMSeYjruv3vdWWmgUq0cl
Gac2qJSRtAMmgLuHWMjf7N5mxOTOnKejU4o2i9cJ+YHmWKOdCigv2Ge1UadOQFlC
E7tRPiUR3asfDfj+e+LVTTdToH6p8pk+mOUzIoZ8jIkQ+IXzi62UDl5+Rw9mqiuX
1CtqEMUXxo2qwX+d4TcV/QUOp0YKPuIcUZ9NMMS+S3lOyJ4NFt+j2Izk7QJp5kNP
gKVqB68TjDQsBuDr3P9ynlHbduxTIhZAqopbTrLe0FIg48nUe4n1yHJBVzqaVajX
rFBJSsSUffBLAARNPSXJJhIgc2C1/qOC8dgMeDMcR2kPirDHaQZ/lY1yEpq1yiqR
q6e3v5hvIAm4IjbYk0mF7TUxBrPGVE/ExyBINyASRoYxAJ1PyeD/iljZ9vI3asRA
s+hhxT8H3f7lnqTrmJqMjHgAdGkmag07EdmvFNX4xK4aADSy7Y6g4dw25ffRopo9
p9Jf9HX+dZv65Y3UjbV/6HuXcaSEBJJLSVWvii65PebqSN0LuHEFvNeIJ6Iblx0B
AWh/hd0Iin2gdkcG39Mr
=Z5kM
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights:
- PowerNV PCI hotplug support.
- Lots more Power9 support.
- eBPF JIT support on ppc64le.
- Lots of cxl updates.
- Boot code consolidation.
Bug fixes:
- Fix spin_unlock_wait() from Boqun Feng
- Fix stack pointer corruption in __tm_recheckpoint() from Michael
Neuling
- Fix multiple bugs in memory_hotplug_max() from Bharata B Rao
- mm: Ensure "special" zones are empty from Oliver O'Halloran
- ftrace: Separate the heuristics for checking call sites from
Michael Ellerman
- modules: Never restore r2 for a mprofile-kernel style mcount() call
from Michael Ellerman
- Fix endianness when reading TCEs from Alexey Kardashevskiy
- start rtasd before PCI probing from Greg Kurz
- PCI: rpaphp: Fix slot registration for multiple slots under a PHB
from Tyrel Datwyler
- powerpc/mm: Add memory barrier in __hugepte_alloc() from Sukadev
Bhattiprolu
Cleanups & fixes:
- Drop support for MPIC in pseries from Rashmica Gupta
- Define and use PPC64_ELF_ABI_v2/v1 from Michael Ellerman
- Remove unused symbols in asm-offsets.c from Rashmica Gupta
- Fix SRIOV not building without EEH enabled from Russell Currey
- Remove kretprobe_trampoline_holder from Thiago Jung Bauermann
- Reduce log level of PCI I/O space warning from Benjamin
Herrenschmidt
- Add array bounds checking to crash_shutdown_handlers from Suraj
Jitindar Singh
- Avoid -maltivec when using clang integrated assembler from Anton
Blanchard
- Fix array overrun in ppc_rtas() syscall from Andrew Donnellan
- Fix error return value in cmm_mem_going_offline() from Rasmus
Villemoes
- export cpu_to_core_id() from Mauricio Faria de Oliveira
- Remove old symbols from defconfigs from Andrew Donnellan
- Update obsolete comments in setup_32.c about entry conditions from
Benjamin Herrenschmidt
- Add comment explaining the purpose of setup_kdump_trampoline() from
Benjamin Herrenschmidt
- Merge the RELOCATABLE config entries for ppc32 and ppc64 from Kevin
Hao
- Remove RELOCATABLE_PPC32 from Kevin Hao
- Fix .long's in tlb-radix.c to more meaningful from Balbir Singh
Minor cleanups & fixes:
- Andrew Donnellan, Anna-Maria Gleixner, Anton Blanchard, Benjamin
Herrenschmidt, Bharata B Rao, Christophe Leroy, Colin Ian King,
Geliang Tang, Greg Kurz, Madhavan Srinivasan, Michael Ellerman,
Michael Ellerman, Stephen Rothwell, Stewart Smith.
Freescale updates from Scott:
- "Highlights include more 8xx optimizations, device tree updates,
and MVME7100 support."
PowerNV PCI hotplug from Gavin Shan:
- PCI: Add pcibios_setup_bridge()
- Override pcibios_setup_bridge()
- Remove PCI_RESET_DELAY_US
- Move pnv_pci_ioda_setup_opal_tce_kill() around
- Increase PE# capacity
- Allocate PE# in reverse order
- Create PEs in pcibios_setup_bridge()
- Setup PE for root bus
- Extend PCI bridge resources
- Make pnv_ioda_deconfigure_pe() visible
- Dynamically release PE
- Update bridge windows on PCI plug
- Delay populating pdn
- Support PCI slot ID
- Use PCI slot reset infrastructure
- Introduce pnv_pci_get_slot_id()
- Functions to get/set PCI slot state
- PCI/hotplug: PowerPC PowerNV PCI hotplug driver
- Print correct PHB type names
Power9 idle support from Shreyas B. Prabhu:
- set power_save func after the idle states are initialized
- Use PNV_THREAD_WINKLE macro while requesting for winkle
- make hypervisor state restore a function
- Rename idle_power7.S to idle_book3s.S
- Rename reusable idle functions to hardware agnostic names
- Make pnv_powersave_common more generic
- abstraction for saving SPRs before entering deep idle states
- Add platform support for stop instruction
- cpuidle/powernv: Use CPUIDLE_STATE_MAX instead of MAX_POWERNV_IDLE_STATES
- cpuidle/powernv: cleanup cpuidle-powernv.c
- cpuidle/powernv: Add support for POWER ISA v3 idle states
- Use deepest stop state when cpu is offlined
Power9 PMU from Madhavan Srinivasan:
- factor out power8 pmu macros and defines
- factor out power8 pmu functions
- factor out power8 __init_pmu code
- Add power9 event list macros for generic and cache events
- Power9 PMU support
- Export Power9 generic and cache events to sysfs
Power9 preliminary interrupt & PCI support from Benjamin Herrenschmidt:
- Add XICS emulation APIs
- Move a few exception common handlers to make room
- Add support for HV virtualization interrupts
- Add mechanism to force a replay of interrupts
- Add ICP OPAL backend
- Discover IODA3 PHBs
- pci: Remove obsolete SW invalidate
- opal: Add real mode call wrappers
- Rename TCE invalidation calls
- Remove SWINV constants and obsolete TCE code
- Rework accessing the TCE invalidate register
- Fallback to OPAL for TCE invalidations
- Use the device-tree to get available range of M64's
- Check status of a PHB before using it
- pci: Don't try to allocate resources that will be reassigned
Other Power9:
- Send SIGBUS on unaligned copy and paste from Chris Smart
- Large Decrementer support from Oliver O'Halloran
- Load Monitor Register Support from Jack Miller
Performance improvements from Anton Blanchard:
- Avoid load hit store in __giveup_fpu() and __giveup_altivec()
- Avoid load hit store in setup_sigcontext()
- Remove assembly versions of strcpy, strcat, strlen and strcmp
- Align hot loops of some string functions
eBPF JIT from Naveen N. Rao:
- Fix/enhance 32-bit Load Immediate implementation
- Optimize 64-bit Immediate loads
- Introduce rotate immediate instructions
- A few cleanups
- Isolate classic BPF JIT specifics into a separate header
- Implement JIT compiler for extended BPF
Operator Panel driver from Suraj Jitindar Singh:
- devicetree/bindings: Add binding for operator panel on FSP machines
- Add inline function to get rc from an ASYNC_COMP opal_msg
- Add driver for operator panel on FSP machines
Sparse fixes from Daniel Axtens:
- make some things static
- Introduce asm-prototypes.h
- Include headers containing prototypes
- Use #ifdef __BIG_ENDIAN__ #else for REG_BYTE
- kvm: Clarify __user annotations
- Pass endianness to sparse
- Make ppc_md.{halt, restart} __noreturn
MM fixes & cleanups from Aneesh Kumar K.V:
- radix: Update LPCR HR bit as per ISA
- use _raw variant of page table accessors
- Compile out radix related functions if RADIX_MMU is disabled
- Clear top 16 bits of va only on older cpus
- Print formation regarding the the MMU mode
- hash: Update SDR1 size encoding as documented in ISA 3.0
- radix: Update PID switch sequence
- radix: Update machine call back to support new HCALL.
- radix: Add LPID based tlb flush helpers
- radix: Add a kernel command line to disable radix
- Cleanup LPCR defines
Boot code consolidation from Benjamin Herrenschmidt:
- Move epapr_paravirt_early_init() to early_init_devtree()
- cell: Don't use flat device-tree after boot
- ge_imp3a: Don't use the flat device-tree after boot
- mpc85xx_ds: Don't use the flat device-tree after boot
- mpc85xx_rdb: Don't use the flat device-tree after boot
- Don't test for machine type in rtas_initialize()
- Don't test for machine type in smp_setup_cpu_maps()
- dt: Add of_device_compatible_match()
- Factor do_feature_fixup calls
- Move 64-bit feature fixup earlier
- Move 64-bit memory reserves to setup_arch()
- Use a cachable DART
- Move FW feature probing out of pseries probe()
- Put exception configuration in a common place
- Remove early allocation of the SMU command buffer
- Move MMU backend selection out of platform code
- pasemi: Remove IOBMAP allocation from platform probe()
- mm/hash: Don't use machine_is() early during boot
- Don't test for machine type to detect HEA special case
- pmac: Remove spurrious machine type test
- Move hash table ops to a separate structure
- Ensure that ppc_md is empty before probing for machine type
- Move 64-bit probe_machine() to later in the boot process
- Move 32-bit probe() machine to later in the boot process
- Get rid of ppc_md.init_early()
- Move the boot time info banner to a separate function
- Move setting of {i,d}cache_bsize to initialize_cache_info()
- Move the content of setup_system() to setup_arch()
- Move cache info inits to a separate function
- Re-order the call to smp_setup_cpu_maps()
- Re-order setup_panic()
- Make a few boot functions __init
- Merge 32-bit and 64-bit setup_arch()
Other new features:
- tty/hvc: Use IRQF_SHARED for OPAL hvc consoles from Sam Mendoza-Jonas
- tty/hvc: Use opal irqchip interface if available from Sam Mendoza-Jonas
- powerpc: Add module autoloading based on CPU features from Alastair D'Silva
- crypto: vmx - Convert to CPU feature based module autoloading from Alastair D'Silva
- Wake up kopald polling thread before waiting for events from Benjamin Herrenschmidt
- xmon: Dump ISA 2.06 SPRs from Michael Ellerman
- xmon: Dump ISA 2.07 SPRs from Michael Ellerman
- Add a parameter to disable 1TB segs from Oliver O'Halloran
- powerpc/boot: Add OPAL console to epapr wrappers from Oliver O'Halloran
- Assign fixed PHB number based on device-tree properties from Guilherme G. Piccoli
- pseries: Add pseries hotplug workqueue from John Allen
- pseries: Add support for hotplug interrupt source from John Allen
- pseries: Use kernel hotplug queue for PowerVM hotplug events from John Allen
- pseries: Move property cloning into its own routine from Nathan Fontenot
- pseries: Dynamic add entires to associativity lookup array from Nathan Fontenot
- pseries: Auto-online hotplugged memory from Nathan Fontenot
- pseries: Remove call to memblock_add() from Nathan Fontenot
cxl:
- Add set and get private data to context struct from Michael Neuling
- make base more explicitly non-modular from Paul Gortmaker
- Use for_each_compatible_node() macro from Wei Yongjun
- Frederic Barrat
- Abstract the differences between the PSL and XSL
- Make vPHB device node match adapter's
- Philippe Bergheaud
- Add mechanism for delivering AFU driver specific events
- Ignore CAPI adapters misplaced in switched slots
- Refine slice error debug messages
- Andrew Donnellan
- static-ify variables to fix sparse warnings
- PCI/hotplug: pnv_php: export symbols and move struct types needed by cxl
- PCI/hotplug: pnv_php: handle OPAL_PCI_SLOT_OFFLINE power state
- Add cxl_check_and_switch_mode() API to switch bi-modal cards
- remove dead Kconfig options
- fix potential NULL dereference in free_adapter()
- Ian Munsie
- Update process element after allocating interrupts
- Add support for CAPP DMA mode
- Fix allowing bogus AFU descriptors with 0 maximum processes
- Fix allocating a minimum of 2 pages for the SPA
- Fix bug where AFU disable operation had no effect
- Workaround XSL bug that does not clear the RA bit after a reset
- Fix NULL pointer dereference on kernel contexts with no AFU interrupts
- powerpc/powernv: Split cxl code out into a separate file
- Add cxl_slot_is_supported API
- Enable bus mastering for devices using CAPP DMA mode
- Move cxl_afu_get / cxl_afu_put to base
- Allow a default context to be associated with an external pci_dev
- Do not create vPHB if there are no AFU configuration records
- powerpc/powernv: Add support for the cxl kernel api on the real phb
- Add support for using the kernel API with a real PHB
- Add kernel APIs to get & set the max irqs per context
- Add preliminary workaround for CX4 interrupt limitation
- Add support for interrupts on the Mellanox CX4
- Workaround PE=0 hardware limitation in Mellanox CX4
- powerpc/powernv: Fix pci-cxl.c build when CONFIG_MODULES=n
selftests:
- Test unaligned copy and paste from Chris Smart
- Load Monitor Register Tests from Jack Miller
- Cyril Bur
- exec() with suspended transaction
- Use signed long to read perf_event_paranoid
- Fix usage message in context_switch
- Fix generation of vector instructions/types in context_switch
- Michael Ellerman
- Use "Delta" rather than "Error" in normal output
- Import Anton's mmap & futex micro benchmarks
- Add a test for PROT_SAO"
* tag 'powerpc-4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (263 commits)
powerpc/mm: Parenthesise IS_ENABLED() in if condition
tty/hvc: Use opal irqchip interface if available
tty/hvc: Use IRQF_SHARED for OPAL hvc consoles
selftests/powerpc: exec() with suspended transaction
powerpc: Improve comment explaining why we modify VRSAVE
powerpc/mm: Drop unused externs for hpte_init_beat[_v3]()
powerpc/mm: Rename hpte_init_lpar() and move the fallback to a header
powerpc/mm: Fix build break when PPC_NATIVE=n
crypto: vmx - Convert to CPU feature based module autoloading
powerpc: Add module autoloading based on CPU features
powerpc/powernv/ioda: Fix endianness when reading TCEs
powerpc/mm: Add memory barrier in __hugepte_alloc()
powerpc/modules: Never restore r2 for a mprofile-kernel style mcount() call
powerpc/ftrace: Separate the heuristics for checking call sites
powerpc: Merge 32-bit and 64-bit setup_arch()
powerpc/64: Make a few boot functions __init
powerpc: Re-order setup_panic()
powerpc: Re-order the call to smp_setup_cpu_maps()
powerpc/32: Move cache info inits to a separate function
powerpc/64: Move the content of setup_system() to setup_arch()
...
Pull security subsystem updates from James Morris:
"Highlights:
- TPM core and driver updates/fixes
- IPv6 security labeling (CALIPSO)
- Lots of Apparmor fixes
- Seccomp: remove 2-phase API, close hole where ptrace can change
syscall #"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (156 commits)
apparmor: fix SECURITY_APPARMOR_HASH_DEFAULT parameter handling
tpm: Add TPM 2.0 support to the Nuvoton i2c driver (NPCT6xx family)
tpm: Factor out common startup code
tpm: use devm_add_action_or_reset
tpm2_i2c_nuvoton: add irq validity check
tpm: read burstcount from TPM_STS in one 32-bit transaction
tpm: fix byte-order for the value read by tpm2_get_tpm_pt
tpm_tis_core: convert max timeouts from msec to jiffies
apparmor: fix arg_size computation for when setprocattr is null terminated
apparmor: fix oops, validate buffer size in apparmor_setprocattr()
apparmor: do not expose kernel stack
apparmor: fix module parameters can be changed after policy is locked
apparmor: fix oops in profile_unpack() when policy_db is not present
apparmor: don't check for vmalloc_addr if kvzalloc() failed
apparmor: add missing id bounds check on dfa verification
apparmor: allow SYS_CAP_RESOURCE to be sufficient to prlimit another task
apparmor: use list_next_entry instead of list_entry_next
apparmor: fix refcount race when finding a child profile
apparmor: fix ref count leak when profile sha1 hash is read
apparmor: check that xindex is in trans_table bounds
...
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 4.8:
API:
- first part of skcipher low-level conversions
- add KPP (Key-agreement Protocol Primitives) interface.
Algorithms:
- fix IPsec/cryptd reordering issues that affects aesni
- RSA no longer does explicit leading zero removal
- add SHA3
- add DH
- add ECDH
- improve DRBG performance by not doing CTR by hand
Drivers:
- add x86 AVX2 multibuffer SHA256/512
- add POWER8 optimised crc32c
- add xts support to vmx
- add DH support to qat
- add RSA support to caam
- add Layerscape support to caam
- add SEC1 AEAD support to talitos
- improve performance by chaining requests in marvell/cesa
- add support for Araneus Alea I USB RNG
- add support for Broadcom BCM5301 RNG
- add support for Amlogic Meson RNG
- add support Broadcom NSP SoC RNG"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (180 commits)
crypto: vmx - Fix aes_p8_xts_decrypt build failure
crypto: vmx - Ignore generated files
crypto: vmx - Adding support for XTS
crypto: vmx - Adding asm subroutines for XTS
crypto: skcipher - add comment for skcipher_alg->base
crypto: testmgr - Print akcipher algorithm name
crypto: marvell - Fix wrong flag used for GFP in mv_cesa_dma_add_iv_op
crypto: nx - off by one bug in nx_of_update_msc()
crypto: rsa-pkcs1pad - fix rsa-pkcs1pad request struct
crypto: scatterwalk - Inline start/map/done
crypto: scatterwalk - Remove unnecessary BUG in scatterwalk_start
crypto: scatterwalk - Remove unnecessary advance in scatterwalk_pagedone
crypto: scatterwalk - Fix test in scatterwalk_done
crypto: api - Optimise away crypto_yield when hard preemption is on
crypto: scatterwalk - add no-copy support to copychunks
crypto: scatterwalk - Remove scatterwalk_bytes_sglen
crypto: omap - Stop using crypto scatterwalk_bytes_sglen
crypto: skcipher - Remove top-level givcipher interface
crypto: user - Remove crypto_lookup_skcipher call
crypto: cts - Convert to skcipher
...
The comment explaining why we modify VRSAVE is misleading, glibc
does rely on the behaviour. Update the comment.
Signed-off-by: Anton Blanchard <anton@samba.org>
Reviewed-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In the module loader we process relocations, and for long jumps we
generate trampolines (aka stubs). At the call site for one of these
trampolines we usually need to generate a load instruction to restore
the TOC pointer into r2.
There is one exception however, which is calls to mcount() using the
mprofile-kernel ABI, they handle the TOC inside the stub, and so for
them we do not generate a TOC load.
The bug is in how the code in restore_r2() decides if it needs to
generate the TOC load. It does so by looking for a nop following the
branch, and if it sees a nop, it replaces it with the load. In general
the compiler has no reason to generate a nop following the mcount()
call and so that check works OK.
However if we combine a jump label at the start of a function, with an
early return, such that GCC applies the shrink-wrapping optimisation, we
can then end up with an mcount call followed immediately by a nop.
However the nop is not there for a TOC load, it is for the jump label.
That confuses restore_r2() into replacing the jump label nop with a TOC
load, which in turn confuses ftrace into replacing the mcount call with
a b +8 (fixed in the previous commit). The end result is we jump over
the jump label, which if it was supposed to return means we incorrectly
run the body of the function.
We have seen this in practice with some yet-to-be-merged patches that
use jump labels more extensively.
The fix is relatively simple, in restore_r2() we check for an
mprofile-kernel style mcount() call first, before looking for the
presence of a nop.
Fixes: 153086644f ("powerpc/ftrace: Add support for -mprofile-kernel ftrace ABI")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In __ftrace_make_nop() (the 64-bit version), we have code to deal with
two ftrace ABIs. There is the original ABI, which looks mostly like a
function call, and then the mprofile-kernel ABI which is just a branch.
The code tries to handle both cases, by looking for the presence of a
load to restore the TOC pointer (PPC_INST_LD_TOC). If we detect the TOC
load, we assume the call site is for an mcount() call using the old ABI.
That means we patch the mcount() call with a b +8, to branch over the
TOC load.
However if the kernel was built with mprofile-kernel, then there will
never be a call site using the original ftrace ABI. If for some reason
we do see a TOC load, then it's there for a good reason, and we should
not jump over it.
So split the code, using the existing CC_USING_MPROFILE_KERNEL. Kernels
built with mprofile-kernel will only look for, and expect, the new ABI,
and similarly for the original ABI.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There is little enough differences now.
mpe: Add a/p/k/setup.h to contain the prototypes and empty versions of
functions we need, rather than using weak functions. Add a few other
empty versions to avoid as many #ifdefs as possible in the code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Do it right after probe_machine() since it's about testing ppc_md,
and put the test in the common code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It makes more sense to do it before intializing xmon() as xmon might
use the info in there. We do want to register the console early
though in case we want some functioning printk's in the cpu map setup.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Matches 64-bit. Also move the call to the same spot as ppc64
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Also remove the completely osbolete comment. We *do* look in the
device-tree.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It is now called right after platform probe, so the probe function
can just do the job.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This converts all the 32-bit platforms to use the expanded device-tree
which is a pretty mechanical change. Unlike 64-bit, the 32-bit kernel
didn't rely on platform initializations to setup the MMU since it
sets it up entirely before probe_machine() so the move has comparatively
less consequences though it's a bigger patch.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We no long need the machine type that early, so we can move probe_machine()
to after the device-tree has been expanded. This will allow further
consolidation.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Anything in there will be overwritten, so it helps catching nasty
bugs if we check that it's indeed full of NULL's before we do so.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Moving probe_machine() to after mmu init will cause the ppc_md
fields relative to the hash table management to be overwritten.
Since we have essentially disconnected the machine type from
the hash backend ops, finish the job by moving them to a different
structure.
The only callback that didn't quite fix is update_partition_table
since this is not specific to hash, so I moved it to a standalone
variable for now. We can revisit later if needed.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[mpe: Fix ppc64e build failure in kexec]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We move it into early_mmu_init() based on firmware features. For PS3,
we have to move the setting of these into early_init_devtree().
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The various calls to establish exception endianness and AIL are
now done from a single point using already established CPU and FW
feature bits to decide what to do.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We move the function itself to pseries/firmware.c and call it along
with almost all other flat device-tree parsers from early_init_devtree()
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[mpe: Move #ifdefs into the header by providing pseries_probe_fw_features()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There is really no need to do them that early, early_setup() runs
before MMU is on, we should do the strict minimum there to get the
MMU going.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Make it part of early_setup() as we really want the feature fixups
to be applied before we turn on the MMU since they can have an impact
on the various assembly path related to MMU management and interrupts.
This makes 64-bit match what 32-bit does.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
32 and 64-bit do a similar set of calls early on, we move it all to
a single common function to make the boot code more readable.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It is seldom used in the kernel code and can be easily replaced by
either RELOCATABLE or PPC32. So there is no reason to keep a separate
kernel option for this.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds the kernel command line disable_radix which disable
the radix MMU mode even if firmware indicates radix support via
ibm,pa-features device tree node.
This helps in testing different MMU mode easily.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As per ISA, we need to do this only for architecture version 2.02 and
earlier. This continued to work even for 2.07. But let's not do this for
anything after 2.02. ISA 3.0 requires these top bits to be not cleared.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When we know we will reassign all resources, trying (and failing)
to allocate them initially is fairly pointless and leads to a lot
of scary messages in the kernel log
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Replace the old generic opal_call_realmode() with proper per-call
wrappers similar to the normal ones and convert callers.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Calling this function with interrupts soft-disabled will cause
a replay of the external interrupt vector when they are re-enabled.
This will be used by the OPAL XICS backend (and latter by the native
XIVE code) to handle EOI signaling that there are more interrupts to
fetch from the hardware since the hardware won't issue another HW
interrupt in that case.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This will be delivering external interrupts from the XIVE to the
Hypervisor. We treat it as a normal external interrupt for the
lazy irq disable code (so it will be replayed as a 0x500) and
route it to do_IRQ.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This moves the CBE RAS and facility unavailable "common" handlers
down to after the FWNMI page.
This frees up some space in the very demanded spaces before the
relocation-on vectors and before the FWNMI page. They are still
within 64K of __start, so CONFIG_RELOCATABLE should still work.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER ISA v3 defines a new idle processor core mechanism. In summary,
a) new instruction named stop is added. This instruction replaces
instructions like nap, sleep, rvwinkle.
b) new per thread SPR named Processor Stop Status and Control Register
(PSSCR) is added which controls the behavior of stop instruction.
PSSCR layout:
----------------------------------------------------------
| PLS | /// | SD | ESL | EC | PSLL | /// | TR | MTL | RL |
----------------------------------------------------------
0 4 41 42 43 44 48 54 56 60
PSSCR key fields:
Bits 0:3 - Power-Saving Level Status. This field indicates the lowest
power-saving state the thread entered since stop instruction was last
executed.
Bit 42 - Enable State Loss
0 - No state is lost irrespective of other fields
1 - Allows state loss
Bits 44:47 - Power-Saving Level Limit
This limits the power-saving level that can be entered into.
Bits 60:63 - Requested Level
Used to specify which power-saving level must be entered on executing
stop instruction
This patch adds support for stop instruction and PSSCR handling.
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Create a function for saving SPRs before entering deep idle states.
This function can be reused for POWER9 deep idle states.
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
pnv_powersave_common does common steps needed before entering idle
state and eventually changes MSR to MSR_IDLE and does rfid to
pnv_enter_arch207_idle_mode.
Move the updation of HSTATE_HWTHREAD_STATE to pnv_powersave_common
from pnv_enter_arch207_idle_mode and make it more generic by passing the
rfid address as a function parameter.
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Functions like power7_wakeup_loss, power7_wakeup_noloss,
power7_wakeup_tb_loss are used by POWER7 and POWER8 hardware. They can
also be used by POWER9. Hence rename these functions hardware agnostic
names.
Suggested-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
idle_power7.S handles idle entry/exit for POWER7, POWER8 and in next
patch for POWER9. Rename the file to a non-hardware specific
name.
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In the current code, when the thread wakes up in reset vector, some
of the state restore code and check for whether a thread needs to
branch to kvm is duplicated. Reorder the code such that this
duplication is avoided.
At a higher level this is what the change looks like-
Before this patch -
power7_wakeup_tb_loss:
restore hypervisor state
if (thread needed by kvm)
goto kvm_start_guest
restore nvgprs, cr, pc
rfid to process context
power7_wakeup_loss:
restore nvgprs, cr, pc
rfid to process context
reset vector:
if (waking from deep idle states)
goto power7_wakeup_tb_loss
else
if (thread needed by kvm)
goto kvm_start_guest
goto power7_wakeup_loss
After this patch -
power7_wakeup_tb_loss:
restore hypervisor state
return
power7_restore_hyp_resource():
if (waking from deep idle states)
goto power7_wakeup_tb_loss
return
power7_wakeup_loss:
restore nvgprs, cr, pc
rfid to process context
reset vector:
power7_restore_hyp_resource()
if (thread needed by kvm)
goto kvm_start_guest
goto power7_wakeup_loss
Reviewed-by: Paul Mackerras <paulus@samba.org>
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
At the start of __tm_recheckpoint() we save the kernel stack pointer
(r1) in SPRG SCRATCH0 (SPRG2) so that we can restore it after the
trecheckpoint.
Unfortunately, the same SPRG is used in the SLB miss handler. If an
SLB miss is taken between the save and restore of r1 to the SPRG, the
SPRG is changed and hence r1 is also corrupted. We can end up with
the following crash when we start using r1 again after the restore
from the SPRG:
Oops: Bad kernel stack pointer, sig: 6 [#1]
SMP NR_CPUS=2048 NUMA pSeries
CPU: 658 PID: 143777 Comm: htm_demo Tainted: G EL X 4.4.13-0-default #1
task: c0000b56993a7810 ti: c00000000cfec000 task.ti: c0000b56993bc000
NIP: c00000000004f188 LR: 00000000100040b8 CTR: 0000000010002570
REGS: c00000000cfefd40 TRAP: 0300 Tainted: G EL X (4.4.13-0-default)
MSR: 8000000300001033 <SF,ME,IR,DR,RI,LE> CR: 02000424 XER: 20000000
CFAR: c000000000008468 DAR: 00003ffd84e66880 DSISR: 40000000 SOFTE: 0
PACATMSCRATCH: 00003ffbc865e680
GPR00: fffffffcfabc4268 00003ffd84e667a0 00000000100d8c38 000000030544bb80
GPR04: 0000000000000002 00000000100cf200 0000000000000449 00000000100cf100
GPR08: 000000000000c350 0000000000002569 0000000000002569 00000000100d6c30
GPR12: 00000000100d6c28 c00000000e6a6b00 00003ffd84660000 0000000000000000
GPR16: 0000000000000003 0000000000000449 0000000010002570 0000010009684f20
GPR20: 0000000000800000 00003ffd84e5f110 00003ffd84e5f7a0 00000000100d0f40
GPR24: 0000000000000000 0000000000000000 0000000000000000 00003ffff0673f50
GPR28: 00003ffd84e5e960 00000000003d0f00 00003ffd84e667a0 00003ffd84e5e680
NIP [c00000000004f188] restore_gprs+0x110/0x17c
LR [00000000100040b8] 0x100040b8
Call Trace:
Instruction dump:
f8a1fff0 e8e700a8 38a00000 7ca10164 e8a1fff8 e821fff0 7c0007dd 7c421378
7db142a6 7c3242a6 38800002 7c810164 <e9c100e0> e9e100e8 ea0100f0 ea2100f8
We hit this on large memory machines (> 2TB) but it can also be hit on
smaller machines when 1TB segments are disabled.
To hit this, you also need to be virtualised to ensure SLBs are
periodically removed by the hypervisor.
This patches moves the saving of r1 to the SPRG to the region where we
are guaranteed not to take any further SLB misses.
Fixes: 98ae22e15b ("powerpc: Add helper functions for transactional memory context switching")
Cc: stable@vger.kernel.org # v3.9+
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- tm: Always reclaim in start_thread() for exec() class syscalls from Cyril Bur
- tm: Avoid SLB faults in treclaim/trecheckpoint when RI=0 from Michael Neuling
- eeh: Fix wrong argument passed to eeh_rmv_device() from Gavin Shan
- Initialise pci_io_base as early as possible from Darren Stevens
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=oEAY
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.7-5' into next
Pull in the fixes we sent during 4.7, we have code we want to merge into
next that depends on some of them.
powernv marks it's halt and restart calls as __noreturn. However,
ppc_md does not have this annotation. Add the annotation to ppc_md,
and then to every halt/restart function that is missing it.
Additionally, I have verified that all of these functions do not
return. Occasionally I have added a spin loop to be sure.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The array crash_shutdown_handles[] has size CRASH_HANDLER_MAX, thus when
we loop over the elements of the list we check crash_shutdown_handles[i]
&& i < CRASH_HANDLER_MAX. However this means that when we increment i to
CRASH_HANDLER_MAX we will perform an out of bound array access checking
the first condition before exiting on the second condition.
To avoid the out of bounds access, simply reorder the loop conditions.
Fixes: 1d1451655b ("powerpc: Add array bounds checking to crash_shutdown_handlers")
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The subsequent test for RTAS along with the LPAR test are sufficient
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The test is unnecessary, the FW_FEATURE_LPAR is sufficient as there
exist no other LPAR type that has RTAS.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The function is called by both 32-bit and 64-bit early setup right
after early_init_devtree(). All it does is run yet another early
DT parser which is precisely what early_init_devtree() is about,
so move it in there.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Anything in early_setup() needs to be justified to be there, in
this case, we need the trampolines before we can take exceptions
and thus before we turn on the MMU.
Also remove a pretty meaningless and misplaced debug message
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[mpe: Fix comment formatting]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
early_init() is called in-place before kernel relocation and using
whatever MMU setup exists at the point the kernel is entered.
machine_init() is called after relocation and after some initial
mapping of PAGE_OFFSET has been established (typically using BATs
on 6xx/7xx/7xxx processors or some form of bolted TLB on others).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The asm-offsets mechanism generates signed numbers, even if the
input value is explicitly unsigned. This causes a problem with
older binutils (e.g. 2.23), which sign-extend a negative number
when @h is applied. Thus, this instruction:
cmpli cr0, r11, VIRT_IMMR_BASE@h
resulted in this:
Error: operand out of range (0xfffffff0 is not between 0x00000000 and
0x0000ffff)
By casting to a larger type, we can force the output to be expressed
as a positive number.
Signed-off-by: Scott Wood <oss@buserror.net>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
CONFIG_PIN_TLB maps IMMR area and the first 24 Mbytes of memory.
In some circunstances it might be more interesting to not map
IMMR but map 32 Mbytes of memory instead.
Therefore we add config option CONFIG_PIN_TLB_IMMR to select if
IMMR shall be pinned or not, hence whether we pin 24 or 32 Mbytes of RAM
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
On recent kernels, with some debug options like for instance
CONFIG_LOCKDEP, the BSS requires more than 8M memory, allthough
the kernel code fits in the first 8M.
Today, it is necessary to activate CONFIG_PIN_TLB to get more than 8M
at startup, allthough pinning TLB is not necessary for that.
We could have inconditionaly mapped 16 or 24M bytes at startup
but some old hardware only have 8M and mapping non-existing RAM
would be an issue due to speculative accesses.
With the preceding patch however, the TLB entries are populated on
demand. By setting up the TLB miss handler to handle up to 24M until
the handler is patched for the entire memory space, it is possible
to allow access up to more memory without mapping non-existing RAM.
It is therefore not needed anymore to map memory data at all
at startup. It will be handled by the TLB miss handler.
One might still want to PIN the IMMR and the first 24M of RAM.
It is now possible to do it in the C memory initialisation
functions. In addition, we now know how much memory we have
when we do it, so we are able to adapt the pining to the
real amount of memory available. So boards with less than 24M
can now also benefit from PIN_TLB.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
Instead of using the first level page table to define mappings for
the linear memory space, we can use direct mapping from the TLB
handling routines. This has several advantages:
* No need to read the tables at each TLB miss
* No issue in 16k pages mode where the 1st level table maps 64 Mbytes
The size of the available linear space is known at system startup.
In order to avoid data access at each TLB miss to know the memory
size, the TLB routine is patched at startup with the proper size
This patch provides a 10%-15% improvment of TLB miss handling for
kernel addresses
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
Bootloader may have pinned some TLB entries so the kernel must
unpin them before flushing TLBs with tlbia otherwise pinned TLB
entries won't get flushed
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
Once the linear memory space has been mapped with 8Mb pages, as
seen in the related commit, we get 11 millions DTLB missed during
the reference 600s period. 77% of the misses are on user addresses
and 23% are on kernel addresses (1 fourth for linear address space
and 3 fourth for virtual address space)
Traditionaly, each driver manages one computer board which has its
own components with its own memory maps.
But on embedded chips like the MPC8xx, the SOC has all registers
located in the same IO area.
When looking at ioremaps done during startup, we see that
many drivers are re-mapping small parts of the IMMR for their own use
and all those small pieces gets their own 4k page, amplifying the
number of TLB misses: in our system we get 0xff000000 mapped 31 times
and 0xff003000 mapped 9 times.
Even if each part of IMMR was mapped only once with 4k pages, it would
still be several small mappings towards linear area.
This patch maps the IMMR with a single 512k page.
With this patch applied, the number of DTLB misses during the 10 min
period is reduced to 11.8 millions for a duration of 5.8s, which
represents 2% of the non-idle time hence yet another 10% reduction.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
Memory: 124428K/131072K available (3748K kernel code, 188K rwdata,
648K rodata, 508K init, 290K bss, 6644K reserved)
Kernel virtual memory layout:
* 0xfffdf000..0xfffff000 : fixmap
* 0xfde00000..0xfe000000 : consistent mem
* 0xfddf6000..0xfde00000 : early ioremap
* 0xc9000000..0xfddf6000 : vmalloc & ioremap
SLUB: HWalign=16, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Today, IMMR is mapped 1:1 at startup
Mapping IMMR 1:1 is just wrong because it may overlap with another
area. On most mpc8xx boards it is OK as IMMR is set to 0xff000000
but for instance on EP88xC board, IMMR is at 0xfa200000 which
overlaps with VM ioremap area
This patch fixes the virtual address for remapping IMMR with the fixmap
regardless of the value of IMMR.
The size of IMMR area is 256kbytes (CPM at offset 0, security engine
at offset 128k) so a 512k page is enough
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
This patch provides VIRT_CPU_ACCOUTING to PPC32 architecture.
PPC32 doesn't have the PACA structure, so we use the task_info
structure to store the accounting data.
In order to reuse on PPC32 the PPC64 functions, all u64 data has
been replaced by 'unsigned long' so that it is u32 on PPC32 and
u64 on PPC64
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
eeh_cache.c doesn't build cleanly with -DDEBUG when
CONFIG_PHYS_ADDR_T_64BIT is set, as a couple of pr_debug()s use "%lx" for
resource_size_t parameters.
Use "%pap" instead, as it's the correct format specifier for types deriving
from phys_addr_t.
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
A strange behaviour is observed when comparing PCI hotplug in QEMU, between
x86 and pseries. If you consider the following steps:
- start a VM
- add a PCI device via the QEMU monitor before the rtasd has started (for
example starting the VM in paused state, or hotplug during FW or boot
loader)
- resume the VM execution
The x86 kernel detects the PCI device, but the pseries one does not.
This happens because the rtasd kernel worker is currently started under
device_initcall, while PCI probing happens earlier under subsys_initcall.
As a consequence, if we have a pending RTAS event at boot time, a message
is printed and the event is dropped.
This patch moves all the initialization of rtasd to arch_initcall, which is
run before subsys_call: this way, logging_enabled is true when the RTAS
event pops up and it is not lost anymore.
The proc fs bits stay at device_initcall because they cannot be run before
fs_initcall.
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The domain/PHB field of PCI addresses has its value obtained from a
global variable, incremented each time a new domain (represented by
struct pci_controller) is added on the system. The domain addition
process happens during boot or due to PHB hotplug add.
As recent kernels are using predictable naming for network interfaces,
the network stack is more tied to PCI naming. This can be a problem in
hotplug scenarios, because PCI addresses will change if devices are
removed and then re-added. This situation seems unusual, but it can
happen if a user wants to replace a NIC without rebooting the machine,
for example.
This patch changes the way PCI domain values are generated: now, we use
device-tree properties to assign fixed PHB numbers to PCI addresses
when available (meaning pSeries and PowerNV cases). We also use a bitmap
to allow dynamic PHB numbering when device-tree properties are not
used. This bitmap keeps track of used PHB numbers and if a PHB is
released (by hotplug operations for example), it allows the reuse of
this PHB number, avoiding PCI address to change in case of device remove
and re-add soon after. No functional changes were introduced.
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Ian Munsie <imunsie@au1.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
[mpe: Drop unnecessary machine_is(pseries) test]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Despite attempting to fix this in commit fb36e90736 ("powerpc/pci: Fix
SRIOV not building without EEH enabled"), the build is still broken when
PCI_IOV=y and EEH=n (eg. g5_defconfig with PCI_IOV=y):
arch/powerpc/kernel/pci_dn.c: In function ‘remove_dev_pci_data’:
arch/powerpc/kernel/pci_dn.c:230:18: error: unused variable ‘edev’
Incorporate Ben's idea of using __maybe_unused to avoid so many #ifdefs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Power ISAv3 adds a large decrementer (LD) mode which increases the size
of the decrementer register. The size of the enlarged decrementer
register is between 32 and 64 bits with the exact size being dependent
on the implementation. When in LD mode, reads are sign extended to 64
bits and a decrementer exception is raised when the high bit is set (i.e
the value goes below zero). Writes however are truncated to the physical
register width so some care needs to be taken to ensure that the high
bit is not set when reloading the decrementer. This patch adds support
for using the LD inside the host kernel on processors that support it.
When LD mode is supported firmware will supply the ibm,dec-bits property
for CPU nodes to allow the kernel to determine the maximum decrementer
value. Enabling LD mode is a hypervisor privileged operation so the kernel
can only enable it manually when running in hypervisor mode. Guests that
support LD mode can request it using the "ibm,client-architecture-support"
firmware call (not implemented in this patch) or some other platform
specific method. If this property is not supplied then the traditional
decrementer width of 32 bit is assumed and LD mode will not be enabled.
This patch was based on initial work by Jack Miller.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If ppc_rtas() is called with args.nargs == 16 and args.nret == 0,
args.rets is set to point to &args.args[16], which is beyond the end of
the args.args array. This results in a minor read overrun of the array
when we check the first return code (which, per PAPR, is a required
output of all RTAS calls) to see if there's been a hardware error.
Change the nargs/nret check to ensure nargs is <= 15, allowing room for
the status code. Users shouldn't be calling with nret == 0, but there's
no real harm if they do, so we don't stop them.
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Calling ISA 3.0 instructions copy, copy_first, paste and paste_last
generates an alignment fault when copying or pasting unaligned
data (128 byte). We catch this and send SIGBUS to the userspace
process that caused it.
We do not emulate these because paste may contain additional metadata
when pasting to a co-processor and paste_last is the synchronisation
point for preceding copy/paste sequences.
Thanks to Michael Neuling <mikey@neuling.org> for his help.
Signed-off-by: Chris Smart <chris@distroguy.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Factor out the power8 pmu init functions to share with
power9. Monitor Mode Control Register S(MMCRS) and
Monitor Mode Control Register H(MMCRH) registers are
dropped in Power9. These registers are added to new
function which are included for power8 init.
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We spent so much time bike-shedding the printk() we missed that the next
line was missing a semi-colon. And it seems none of our defconfigs turn
on CONFIG_FA_DUMP.
Fixes: 4a03749f14 ("powerpc/fadump: Trivial fix of spelling mistake, clean up message")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit d6a9996e84 ("powerpc/mm: vmalloc abstraction in preparation for
radix") turned kernel memory and IO addresses from #defined constants to
variables initialised at runtime.
On PA6T (pasemi) systems the setup_arch() machine call initialises the
onboard PCI-e root-ports, and uses pci_io_base to do this, which is now
before its value has been set, resulting in a panic early in boot before
console IO is initialised.
Move the pci_io_base initialisation to the same place as vmalloc ranges
are set (hash__early_init_mmu()/radix__early_init_mmu()) - this is the
earliest possible place we can initialise it.
Fixes: d6a9996e84 ("powerpc/mm: vmalloc abstraction in preparation for radix")
Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Darren Stevens <darren@stevens-zone.net>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[mpe: Add #ifdef CONFIG_PCI, massage change log slightly]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently we have 2 segments that are bolted for the kernel linear
mapping (ie 0xc000... addresses). This is 0 to 1TB and also the kernel
stacks. Anything accessed outside of these regions may need to be
faulted in. (In practice machines with TM always have 1T segments)
If a machine has < 2TB of memory we never fault on the kernel linear
mapping as these two segments cover all physical memory. If a machine
has > 2TB of memory, there may be structures outside of these two
segments that need to be faulted in. This faulting can occur when
running as a guest as the hypervisor may remove any SLB that's not
bolted.
When we treclaim and trecheckpoint we have a window where we need to
run with the userspace GPRs. This means that we no longer have a valid
stack pointer in r1. For this window we therefore clear MSR RI to
indicate that any exceptions taken at this point won't be able to be
handled. This means that we can't take segment misses in this RI=0
window.
In this RI=0 region, we currently access the thread_struct for the
process being context switched to or from. This thread_struct access
may cause a segment fault since it's not guaranteed to be covered by
the two bolted segment entries described above.
We've seen this with a crash when running as a guest with > 2TB of
memory on PowerVM:
Unrecoverable exception 4100 at c00000000004f138
Oops: Unrecoverable exception, sig: 6 [#1]
SMP NR_CPUS=2048 NUMA pSeries
CPU: 1280 PID: 7755 Comm: kworker/1280:1 Tainted: G X 4.4.13-46-default #1
task: c000189001df4210 ti: c000189001d5c000 task.ti: c000189001d5c000
NIP: c00000000004f138 LR: 0000000010003a24 CTR: 0000000010001b20
REGS: c000189001d5f730 TRAP: 4100 Tainted: G X (4.4.13-46-default)
MSR: 8000000100001031 <SF,ME,IR,DR,LE> CR: 24000048 XER: 00000000
CFAR: c00000000004ed18 SOFTE: 0
GPR00: ffffffffc58d7b60 c000189001d5f9b0 00000000100d7d00 000000003a738288
GPR04: 0000000000002781 0000000000000006 0000000000000000 c0000d1f4d889620
GPR08: 000000000000c350 00000000000008ab 00000000000008ab 00000000100d7af0
GPR12: 00000000100d7ae8 00003ffe787e67a0 0000000000000000 0000000000000211
GPR16: 0000000010001b20 0000000000000000 0000000000800000 00003ffe787df110
GPR20: 0000000000000001 00000000100d1e10 0000000000000000 00003ffe787df050
GPR24: 0000000000000003 0000000000010000 0000000000000000 00003fffe79e2e30
GPR28: 00003fffe79e2e68 00000000003d0f00 00003ffe787e67a0 00003ffe787de680
NIP [c00000000004f138] restore_gprs+0xd0/0x16c
LR [0000000010003a24] 0x10003a24
Call Trace:
[c000189001d5f9b0] [c000189001d5f9f0] 0xc000189001d5f9f0 (unreliable)
[c000189001d5fb90] [c00000000001583c] tm_recheckpoint+0x6c/0xa0
[c000189001d5fbd0] [c000000000015c40] __switch_to+0x2c0/0x350
[c000189001d5fc30] [c0000000007e647c] __schedule+0x32c/0x9c0
[c000189001d5fcb0] [c0000000007e6b58] schedule+0x48/0xc0
[c000189001d5fce0] [c0000000000deabc] worker_thread+0x22c/0x5b0
[c000189001d5fd80] [c0000000000e7000] kthread+0x110/0x130
[c000189001d5fe30] [c000000000009538] ret_from_kernel_thread+0x5c/0xa4
Instruction dump:
7cb103a6 7cc0e3a6 7ca222a6 78a58402 38c00800 7cc62838 08860000 7cc000a6
38a00006 78c60022 7cc62838 0b060000 <e8c701a0> 7ccff120 e8270078 e8a70098
---[ end trace 602126d0a1dedd54 ]---
This fixes this by copying the required data from the thread_struct to
the stack before we clear MSR RI. Then once we clear RI, we only access
the stack, guaranteeing there's no segment miss.
We also tighten the region over which we set RI=0 on the treclaim()
path. This may have a slight performance impact since we're adding an
mtmsr instruction.
Fixes: 090b9284d7 ("powerpc/tm: Clear MSR RI in non-recoverable TM code")
Signed-off-by: Michael Neuling <mikey@neuling.org>
Reviewed-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When calling eeh_rmv_device() in eeh_reset_device() for partial hotplug
case, @rmv_data instead of its address is the proper argument.
Otherwise, the stack frame is corrupted when writing to
@rmv_data (actually its address) in eeh_rmv_device(). It results in
kernel crash as observed.
This fixes the issue by passing @rmv_data, not its address to
eeh_rmv_device() in eeh_reset_device().
Fixes: 67086e32b5 ("powerpc/eeh: powerpc/eeh: Support error recovery for VF PE")
Reported-by: Pridhiviraj Paidipeddi <ppaidipe@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fix trivial spelling mistake "rgistration". Also use pr_err()
instead of printk() and unsplit the string to keep it all on one
line.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
[mpe: Keep rc on the same line, splitting it doesn't help]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Userspace can quite legitimately perform an exec() syscall with a
suspended transaction. exec() does not return to the old process, rather
it load a new one and starts that, the expectation therefore is that the
new process starts not in a transaction. Currently exec() is not treated
any differently to any other syscall which creates problems.
Firstly it could allow a new process to start with a suspended
transaction for a binary that no longer exists. This means that the
checkpointed state won't be valid and if the suspended transaction were
ever to be resumed and subsequently aborted (a possibility which is
exceedingly likely as exec()ing will likely doom the transaction) the
new process will jump to invalid state.
Secondly the incorrect attempt to keep the transactional state while
still zeroing state for the new process creates at least two TM Bad
Things. The first triggers on the rfid to return to userspace as
start_thread() has given the new process a 'clean' MSR but the suspend
will still be set in the hardware MSR. The second TM Bad Thing triggers
in __switch_to() as the processor is still transactionally suspended but
__switch_to() wants to zero the TM sprs for the new process.
This is an example of the outcome of calling exec() with a suspended
transaction. Note the first 700 is likely the first TM bad thing
decsribed earlier only the kernel can't report it as we've loaded
userspace registers. c000000000009980 is the rfid in
fast_exception_return()
Bad kernel stack pointer 3fffcfa1a370 at c000000000009980
Oops: Bad kernel stack pointer, sig: 6 [#1]
CPU: 0 PID: 2006 Comm: tm-execed Not tainted
NIP: c000000000009980 LR: 0000000000000000 CTR: 0000000000000000
REGS: c00000003ffefd40 TRAP: 0700 Not tainted
MSR: 8000000300201031 <SF,ME,IR,DR,LE,TM[SE]> CR: 00000000 XER: 00000000
CFAR: c0000000000098b4 SOFTE: 0
PACATMSCRATCH: b00000010000d033
GPR00: 0000000000000000 00003fffcfa1a370 0000000000000000 0000000000000000
GPR04: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR08: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR12: 00003fff966611c0 0000000000000000 0000000000000000 0000000000000000
NIP [c000000000009980] fast_exception_return+0xb0/0xb8
LR [0000000000000000] (null)
Call Trace:
Instruction dump:
f84d0278 e9a100d8 7c7b03a6 e84101a0 7c4ff120 e8410170 7c5a03a6 e8010070
e8410080 e8610088 e8810090 e8210078 <4c000024> 48000000 e8610178 88ed023b
Kernel BUG at c000000000043e80 [verbose debug info unavailable]
Unexpected TM Bad Thing exception at c000000000043e80 (msr 0x201033)
Oops: Unrecoverable exception, sig: 6 [#2]
CPU: 0 PID: 2006 Comm: tm-execed Tainted: G D
task: c0000000fbea6d80 ti: c00000003ffec000 task.ti: c0000000fb7ec000
NIP: c000000000043e80 LR: c000000000015a24 CTR: 0000000000000000
REGS: c00000003ffef7e0 TRAP: 0700 Tainted: G D
MSR: 8000000300201033 <SF,ME,IR,DR,RI,LE,TM[SE]> CR: 28002828 XER: 00000000
CFAR: c000000000015a20 SOFTE: 0
PACATMSCRATCH: b00000010000d033
GPR00: 0000000000000000 c00000003ffefa60 c000000000db5500 c0000000fbead000
GPR04: 8000000300001033 2222222222222222 2222222222222222 00000000ff160000
GPR08: 0000000000000000 800000010000d033 c0000000fb7e3ea0 c00000000fe00004
GPR12: 0000000000002200 c00000000fe00000 0000000000000000 0000000000000000
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20: 0000000000000000 0000000000000000 c0000000fbea7410 00000000ff160000
GPR24: c0000000ffe1f600 c0000000fbea8700 c0000000fbea8700 c0000000fbead000
GPR28: c000000000e20198 c0000000fbea6d80 c0000000fbeab680 c0000000fbea6d80
NIP [c000000000043e80] tm_restore_sprs+0xc/0x1c
LR [c000000000015a24] __switch_to+0x1f4/0x420
Call Trace:
Instruction dump:
7c800164 4e800020 7c0022a6 f80304a8 7c0222a6 f80304b0 7c0122a6 f80304b8
4e800020 e80304a8 7c0023a6 e80304b0 <7c0223a6> e80304b8 7c0123a6 4e800020
This fixes CVE-2016-5828.
Fixes: bc2a9408fa ("powerpc: Hook in new transactional memory code")
Cc: stable@vger.kernel.org # v3.9+
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If a PHB has no I/O space, there's no need to make it look like
something bad happened, a pr_debug() is plenty enough since this
is the case of all our modern POWER chips.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As part of the Radix MMU support we added some feature sections in the
SLB miss handler. These are intended to catch the case that we
incorrectly take an SLB miss when Radix is enabled, and instead of
crashing weirdly they bail out to a well defined exit path and trigger
an oops.
However the way they were written meant the bailout case was enabled by
default until we did CPU feature patching.
On powermacs the early debug prints in setup_system() can cause an SLB
miss, which happens before code patching, and so the SLB miss handler
would incorrectly bailout and crash during boot.
Fix it by inverting the sense of the feature section, so that the code
which is in place at boot is correct for the hash case. Once we
determine we are using Radix - which will never happen on a powermac -
only then do we patch in the bailout case which unconditionally jumps.
Fixes: caca285e5a ("powerpc/mm/radix: Use STD_MMU_64 to properly isolate hash related code")
Reported-by: Denis Kirjanov <kda@linux-powerpc.org>
Tested-by: Denis Kirjanov <kda@linux-powerpc.org>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The pdn (struct pci_dn) instances are allocated from memblock or
bootmem when creating PCI controller (hoses) in setup_arch(). PCI
hotplug, which will be supported by proceeding patches, releases
PCI device nodes and their corresponding pdn on unplugging event.
The memory chunks for pdn instances allocated from memblock or
bootmem are hard to reused after being released.
This delays creating pdn by pci_devs_phb_init() from setup_arch()
to core_initcall() so that they are allocated from slab. The memory
consumed by pdn can be released to system without problem during
PCI unplugging time. It indicates that pci_dn is unavailable in
setup_arch() and the the fixup on pdn (like AGP's) can't be carried
out that time. We have to do that in pcibios_root_bridge_prepare()
on maple/pasemi/powermac platforms where/when the pdn is available.
pcibios_root_bridge_prepare is called from subsys_initcall() which
is executed after core_initcall() so the code flow does not change.
At the mean while, the EEH device is created when pdn is populated,
meaning pdn and EEH device have same life cycle. In turn, we needn't
call eeh_dev_init() to create EEH device explicitly.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On the PCI plugging event, PCI slot's subordinate devices are
scanned and their (IO and MMIO) resources are assigned. Platform
dependent resources (PE#, IO/MMIO/DMA windows) are allocated or
created on updating windows of the slot's upstream bridge.
This updates the windows of the hot plugged slot's upstream bridge
in pcibios_finish_adding_to_bus() so that the platform resources
(PE#, IO/MMIO/DMA segments) are allocated or created accordingly.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This overrides pcibios_setup_bridge() that is called to update PCI
bridge windows when PCI resource assignment is completed, to assign
PE and setup various (resource) mapping for the PE in subsequent
patches.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Export cpu_to_core_id(). This will be used by the lpfc driver.
This enables topology_core_id() from <linux/topology.h> (defined
to cpu_to_core_id() in arch/powerpc/include/asm/topology.h) to be
used by (non-builtin) modules.
That is arch-neutral, already used by eg, drivers/base/topology.c,
but it is builtin (obj-y in Makefile) thus didn't need the export.
Since the module uses topology_core_id() and this is defined to
cpu_to_core_id(), it needs the export, otherwise:
ERROR: "cpu_to_core_id" [drivers/scsi/lpfc/lpfc.ko] undefined!
Tested on next-20160601.
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This enables new registers, LMRR and LMSER, that can trigger an EBB in
userspace code when a monitored load (via the new ldmx instruction)
loads memory from a monitored space. This facility is controlled by a
new FSCR bit, LM.
This patch disables the FSCR LM control bit on task init and enables
that bit when a load monitor facility unavailable exception is taken
for using it. On context switch, this bit is then used to determine
whether the two relevant registers are saved and restored. This is
done lazily for performance reasons.
Signed-off-by: Jack Miller <jack@codezen.org>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This fixes a few issues with FSCR init and switching.
In commit 152d523e63 ("powerpc: Create context switch helpers
save_sprs() and restore_sprs()") we moved the setting of the FSCR
register from inside an CPU_FTR_ARCH_207S section to inside just a
CPU_FTR_ARCH_DSCR section. Hence we are setting FSCR on POWER6/7 where
the FSCR doesn't exist. This is harmless but we shouldn't do it.
Also, we can simplify the FSCR context switch. We don't need to go
through the calculation involving dscr_inherit. We can just restore
what we saved last time.
We also set an initial value in INIT_THREAD, so that pid 1 which is
cloned from that gets a sane value.
Based on patch by Jack Miller.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Current comment in the early_setup_secondary() for paca->soft_enabled
update is misleading. Comment should say to Mark interrupts "disabled"
instead of "enabled". Fix the typo.
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fixes the following testsuite failure:
$ sudo ./perf test -v kallsyms
1: vmlinux symtab matches kallsyms :
--- start ---
test child forked, pid 12489
Using /proc/kcore for kernel object code
Looking at the vmlinux_path (8 entries long)
Using /boot/vmlinux for symbols
0xc00000000003d300: diff name v: .kretprobe_trampoline_holder k: kretprobe_trampoline
Maps only in vmlinux:
c00000000086ca38-c000000000879b6c 87ca38 [kernel].text.unlikely
c000000000879b6c-c000000000bf0000 889b6c [kernel].meminit.text
c000000000bf0000-c000000000c53264 c00000 [kernel].init.text
c000000000c53264-d000000004250000 c63264 [kernel].exit.text
d000000004250000-d000000004450000 0 [libcrc32c]
d000000004450000-d000000004620000 0 [xfs]
d000000004620000-d000000004680000 0 [autofs4]
d000000004680000-d0000000046e0000 0 [x_tables]
d0000000046e0000-d000000004780000 0 [ip_tables]
d000000004780000-d0000000047e0000 0 [rng_core]
d0000000047e0000-ffffffffffffffff 0 [pseries_rng]
Maps in vmlinux with a different name in kallsyms:
Maps only in kallsyms:
d000000000000000-f000000000000000 1000000000010000 [kernel.kallsyms]
f000000000000000-ffffffffffffffff 3000000000010000 [kernel.kallsyms]
test child finished with -1
---- end ----
vmlinux symtab matches kallsyms: FAILED!
The problem is that the kretprobe_trampoline symbol looks like this:
$ eu-readelf -s /boot/vmlinux G kretprobe_trampoline
2431: c000000001302368 24 NOTYPE LOCAL DEFAULT 37 kretprobe_trampoline_holder
2432: c00000000003d300 8 FUNC LOCAL DEFAULT 1 .kretprobe_trampoline_holder
97543: c00000000003d300 0 NOTYPE GLOBAL DEFAULT 1 kretprobe_trampoline
Its type is NOTYPE, and its size is 0, and this is a problem because
symbol-elf.c:dso__load_sym skips function symbols that are not STT_FUNC
or STT_GNU_IFUNC (this is determined by elf_sym__is_function). Even
if the type is changed to STT_FUNC, when dso__load_sym calls
symbols__fixup_duplicate, the kretprobe_trampoline symbol is dropped in
favour of .kretprobe_trampoline_holder because the latter has non-zero
size (as determined by choose_best_symbol).
With this patch, all vmlinux symbols match /proc/kallsyms and the
testcase passes.
Commit c1c355ce14 ("x86/kprobes: Get rid of
kretprobe_trampoline_holder()") gets rid of kretprobe_trampoline_holder
altogether on x86. This commit does the same on powerpc. This change
introduces no regressions on the perf and ftracetest testsuite results.
Reviewed-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When a guest is assigned to a core it converts the host Timebase (TB)
into guest TB by adding guest timebase offset before entering into
guest. During guest exit it restores the guest TB to host TB. This means
under certain conditions (Guest migration) host TB and guest TB can differ.
When we get an HMI for TB related issues the opal HMI handler would
try fixing errors and restore the correct host TB value. With no guest
running, we don't have any issues. But with guest running on the core
we run into TB corruption issues.
If we get an HMI while in the guest, the current HMI handler invokes opal
hmi handler before forcing guest to exit. The guest exit path subtracts
the guest TB offset from the current TB value which may have already
been restored with host value by opal hmi handler. This leads to incorrect
host and guest TB values.
With split-core, things become more complex. With split-core, TB also gets
split and each subcore gets its own TB register. When a hmi handler fixes
a TB error and restores the TB value, it affects all the TB values of
sibling subcores on the same core. On TB errors all the thread in the core
gets HMI. With existing code, the individual threads call opal hmi handle
independently which can easily throw TB out of sync if we have guest
running on subcores. Hence we will need to co-ordinate with all the
threads before making opal hmi handler call followed by TB resync.
This patch introduces a sibling subcore state structure (shared by all
threads in the core) in paca which holds information about whether sibling
subcores are in Guest mode or host mode. An array in_guest[] of size
MAX_SUBCORE_PER_CORE=4 is used to maintain the state of each subcore.
The subcore id is used as index into in_guest[] array. Only primary
thread entering/exiting the guest is responsible to set/unset its
designated array element.
On TB error, we get HMI interrupt on every thread on the core. Upon HMI,
this patch will now force guest to vacate the core/subcore. Primary
thread from each subcore will then turn off its respective bit
from the above bitmap during the guest exit path just after the
guest->host partition switch is complete.
All other threads that have just exited the guest OR were already in host
will wait until all other subcores clears their respective bit.
Once all the subcores turn off their respective bit, all threads will
will make call to opal hmi handler.
It is not necessary that opal hmi handler would resync the TB value for
every HMI interrupts. It would do so only for the HMI caused due to
TB errors. For rest, it would not touch TB value. Hence to make things
simpler, primary thread would call TB resync explicitly once for each
core immediately after opal hmi handler instead of subtracting guest
offset from TB. TB resync call will restore the TB with host value.
Thus we can be sure about the TB state.
One of the primary threads exiting the guest will take up the
responsibility of calling TB resync. It will use one of the top bits
(bit 63) from subcore state flags bitmap to make the decision. The first
primary thread (among the subcores) that is able to set the bit will
have to call the TB resync. Rest all other threads will wait until TB
resync is complete. Once TB resync is complete all threads will then
proceed.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
"User" addresses are shown in /sys/devices/pci.../.../resource and
/proc/bus/pci/devices and used as mmap offsets for /proc/bus/pci/BB/DD.F
files. For I/O port resources on powerpc, these are PCI bus addresses,
i.e., raw BAR values.
Previously pci_resource_to_user() computed the user address by subtracting
"hose->io_base_virt - _IO_BASE" from the resource start:
pci_resource_to_user()
if (IO)
offset = (unsigned long)hose->io_base_virt - _IO_BASE;
*start = rsrc->start - offset;
We've already told the PCI core about that "hose->io_base_virt - _IO_BASE"
offset:
pcibios_setup_phb_resources()
res = &hose->io_resource;
offset = pcibios_io_space_offset();
/* i.e., "offset = hose->io_base_virt - _IO_BASE" */
pci_add_resource_offset(resources, res, offset);
so pcibios_resource_to_bus() knows how to do that translation.
No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
The powerpc-specific __pci_mmap_set_pgprot() does two things:
1) Disables write combining for I/O port space mappings
This only affects procfs mappings. The pci_mmap_resource() sysfs path
only requests write combining for resources with IORESOURCE_PREFETCH
set, which doesn't include I/O resources.
The only way to request write combining for I/O port space mappings
was via the PCIIOC_WRITE_COMBINE ioctl and the proc_bus_pci_mmap()
path, and we recently changed that path to ignore write combining for
I/O, so this code in powerpc is no longer needed.
2) Automatically enables write combining for mappings of prefetchable
resources, even if not requested by the user
Both procfs (via PCIIOC_MMAP_IS_MEM and PCIIOC_WRITE_COMBINE ioctls)
and sysfs (via "resourceN_wc" files, which are created for resources
with IORESOURCE_PREFETCH) provide ways for the user to map PCI memory
space with write combining.
Users that desire write combining should use one of those ways instead
of relying on powerpc-specific behavior.
Remove the powerpc-specific __pci_mmap_set_pgprot().
The user-visible effect of this change is that powerpc users mapping
prefetchable PCI memory space via procfs without PCIIOC_WRITE_COMBINE or
via sysfs "resourceN" (not "resourceN_wc") will get regular uncacheable
mappings instead of the write combining mappings they used to get.
The new behavior matches the behavior on all other arches that support
write combining mapping.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PE primary bus cannot be got from its child devices when having
full hotplug in error recovery. The PE primary bus is cached, which
is done in commit <05ba75f84864> ("powerpc/eeh: Fix stale cached primary
bus"). In eeh_reset_device(), the flag (EEH_PE_PRI_BUS) is cleared
before the PCI hot remove. eeh_pe_bus_get() then returns NULL as the
PE primary bus in pnv_eeh_reset() and it crashes the kernel eventually.
This fixes the issue by clearing the flag (EEH_PE_PRI_BUS) before the
PCI hot add. With it, the PowerNV EEH reset backend (pnv_eeh_reset())
can get valid PE primary bus through eeh_pe_bus_get().
Fixes: 67086e32b5 ("powerpc/eeh: powerpc/eeh: Support error recovery for VF PE")
Reported-by: Pridhiviraj Paidipeddi <ppaiddipe@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On Book3E CPUs (and possibly other configs), it is possible to have SRIOV
(CONFIG_PCI_IOV) set without CONFIG_EEH. The SRIOV code does not check
for this, and if EEH is disabled, pci_dn.c fails to build.
Fix this by gating the EEH-specific code in the SRIOV implementation
behind CONFIG_EEH.
Fixes: 39218cd0 ("powerpc/eeh: EEH device for VF")
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Sparse complains that it doesn't know what REG_BYTE is:
arch/powerpc/kernel/align.c:313:29: error: undefined identifier 'REG_BYTE'
REG_BYTE is defined differently based on whether we're compiling for
LE, BE32 or BE64. Sparse apparently doesn't provide __BIG_ENDIAN__ or
__LITTLE_ENDIAN__, which means we get no definition.
Rather than check for __BIG_ENDIAN__ and then separately for
__LITTLE_ENDIAN__, just switch the #ifdef to check for __BIG_ENDIAN__
and then #else we define the little endian version. Technically that's
dicey because PDP_ENDIAN is also a possibility, but we already do it in
a lot of places so one more hardly matters.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Sometimes headers that provide prototypes for functions are
accidentally omitted from the files that define the functions.
Fix a couple of times that occurs.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Sparse picked up a number of functions that are implemented in C and
then only referred to in asm code.
This introduces asm-prototypes.h, which provides a place for
prototypes of these functions.
This silences some sparse warnings.
Signed-off-by: Daniel Axtens <dja@axtens.net>
[mpe: Add include guards, clean up copyright & GPL text]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This is just a smattering of things picked up by sparse that should
be made static.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The array crash_shutdown_handles is an array of size CRASH_HANDLER_MAX+1
containing up to CRASH_HANDLER_MAX shutdown_handlers. It is assumed to
be NULL terminated, which it is under normal circumstances. Array
accesses in the functions crash_shutdown_unregister() and
default_machine_crash_shutdown() rely on this NULL termination property
when traversing this list and don't protect again out of bounds accesses.
If the NULL terminator were somehow overwritten these functions could
potentially access out of the bounds of the array.
Shrink the array to size CRASH_HANDLER_MAX and implement explicit array
bounds checking when accessing the elements of the
crash_shutdown_handles[] array in crash_shutdown_unregister() and
default_machine_crash_shutdown().
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
THREAD_DSCR:
Added in efcac6589a "powerpc: Per process DSCR + some fixes (try#4)"
Last usage removed in 152d523e63 "powerpc: Create context switch helpers save_sprs() and restore_sprs()"
THREAD_DSCR_INHERIT:
Added in 714332858b "powerpc: Restore correct DSCR in context switch"
Last usage removed in 152d523e63 "powerpc: Create context switch helpers save_sprs() and restore_sprs()"
THREAD_TAR:
Added in 2468dcf641 "powerpc: Add support for context switching the TAR register"
Last usage removed in 152d523e63 "powerpc: Create context switch helpers save_sprs() and restore_sprs()"
THREAD_BESCR, THREAD_EBBHR and THREAD_EBBRR:
Added in 9353374b8e "powerpc: Context switch the new EBB SPRs"
Last usage removed in 152d523e63 "powerpc: Create context switch helpers save_sprs() and restore_sprs()"
THREAD_SIAR, THREAD_SDAR, THREAD_SIER, THREAD_MMCR0, and THREAD_MMCR2:
Added in 59affcd3e4 "powerpc: Context switch more PMU related SPRs"
Last usage removed in b11ae95100 "powerpc: Partial revert of "Context switch more PMU related SPRs""
PACA_LOCK_TOKEN:
Added in 9e368f2915 "KVM: PPC: book3s_hv: Add support for PPC970-family processors"
Last usage removed in c17b98cf60 "KVM: PPC: Book3S HV: Remove code for PPC970 processors"
HCALL_STAT_SIZE, HCALL_STAT_CALLS, HCALL_STAT_TB and HCALL_STAT_PURR:
Added in 57852a853b "[POWERPC] powerpc: Instrument Hypervisor Calls"
Last usage removed in c8cd093a6e "powerpc: tracing: Add hypervisor call tracepoints"
VCPU_EPLC:
Added in d30f6e4800 "KVM: PPC: booke: category E.HV (GS-mode) support"
Never used.
CPU_DOWN_FLUSH:
Added in e7affb1dba "powerpc/cache: add cache flush operation for various e500"
Never used.
CFG_STAMP_XSEC:
Added in 14cf11af6c "powerpc: Merge enough to start building in arch/powerpc."
Last usage removed in 0e469db8f7 "powerpc: Rework VDSO gettimeofday to prevent time going backwards"
KVM_LPCR:
Added in aa04b4cc5b "KVM: PPC: Allocate RMAs (Real Mode Areas) at boot for use by guests"
Last usage removed in a0144e2a6b "KVM: PPC: Book3S HV: Store LPCR value for each virtual core"
GPR15, GPR16, GPR17, GPR18, GPR19, GPR20, GPR21, GPR22, GPR23, GPR24,
GPR25, GPR26, GPR27, GPR28, GPR29, GPR30 and GPR31:
Added in 14cf11af6c "powerpc: Merge enough to start building in arch/powerpc."
Never used.
VCPU_SHADOW_FSCR:
Added in 616dff8602 "KVM: PPC: Book3S PR: Handle Facility interrupt and FSCR"
Never used.
VCPU_SHADOW_SRR1:
Added in a2d56020d1 "KVM: PPC: Book3S PR: Keep volatile reg values in vcpu rather than shadow_vcpu"
Never used.
KVM_SPLIT_SIZE:
Added in b4deba5c41 "KVM: PPC: Book3S HV: Implement dynamicmicro-threading on POWER8"
Never used.
VCPU_VCPUID:
Added in de56a948b9 "KVM: PPC: Add support for Book3S processors in hypervisor mode"
Last usage removed 1b400ba0cd "KVM: PPC: Book3S HV: Improve handling of local vs. global TLB invalidations"
_MQ:
Added in 14cf11af6c "powerpc: Merge enough to start building in arch/powerpc."
Never used.
AUDITCONTEXT:
Added in 14cf11af6c "powerpc: Merge enough to start building in arch/powerpc."
Last usage removed in 401d1f029b "[PATCH] syscall entry/exit revamp"
CLONE_VM:
Added in 14cf11af6c "powerpc: Merge enough to start building in arch/powerpc."
Currently unused.
CLONE_UNTRACED:
Added in 14cf11af6c "powerpc: Merge enough to start building in arch/powerpc."
Currently unused.
Signed-off-by: Rashmica Gupta <rashmicy@gmail.com>
[mpe: Munge change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Close the hole where ptrace can change a syscall out from under seccomp.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Currently, if arch code wants to supply seccomp_data directly to
seccomp (which is generally much faster than having seccomp do it
using the syscall_get_xyz() API), it has to use the two-phase
seccomp hooks. Add it to the easy hooks, too.
Cc: linux-arch@vger.kernel.org
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
We're approaching 20 locations where we need to check for ELF ABI v2.
That's fine, except the logic is a bit awkward, because we have to check
that _CALL_ELF is defined and then what its value is.
So check it once in asm/types.h and define PPC64_ELF_ABI_v2 when ELF ABI
v2 is detected.
We also have a few places where what we're really trying to check is
that we are using the 64-bit v1 ABI, ie. function descriptors. So also
add a #define for that, which simplifies several checks.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
sub_reloc_offset() has not been used since commit
917f0af9e5 ("powerpc: Remove arch/ppc and include/asm-ppc") which
removed include/asm-ppc/prom.h.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In setup_sigcontext(), we set current->thread.vrsave then use it
straight after. Since current is hidden from the compiler via inline
assembly, it cannot optimise this and we end up with a load hit store.
Fix this by using a temporary.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In both __giveup_fpu() and __giveup_altivec() we make two modifications
to tsk->thread.regs->msr. gcc decides to do a read/modify/write of
each change, so we end up with a load hit store:
ld r9,264(r10)
rldicl r9,r9,50,1
rotldi r9,r9,14
std r9,264(r10)
...
ld r9,264(r10)
rldicl r9,r9,40,1
rotldi r9,r9,24
std r9,264(r10)
Fix this by using a temporary.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The recent commit 7cc851039d ("powerpc/pseries: Add POWER8NVL support
to ibm,client-architecture-support call") added a new PVR mask & value
to the start of the ibm_architecture_vec[] array.
However it missed the fact that further down in the array, we hard code
the offset of one of the fields, and then at boot use that value to
patch the value in the array. This means every update to the array must
also update the #define, ugh.
This means that on pseries machines we will misreport to firmware the
number of cores we support, by a factor of threads_per_core.
Fix it for now by updating the #define.
Fixes: 7cc851039d ("powerpc/pseries: Add POWER8NVL support to ibm,client-architecture-support call")
Cc: stable@vger.kernel.org # v4.0+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
gcc-6 correctly warns about a out of bounds access
arch/powerpc/kernel/ptrace.c:407:24: warning: index 32 denotes an offset greater than size of 'u64[32][1] {aka long long unsigned int[32][1]}' [-Warray-bounds]
offsetof(struct thread_fp_state, fpr[32][0]));
^
check the end of array instead of beginning of next element to fix this
Signed-off-by: Khem Raj <raj.khem@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Segher Boessenkool <segher@kernel.crashing.org>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The rtc-generic driver provides an architecture specific
wrapper on top of the generic rtc_class_ops abstraction,
and powerpc has another abstraction on top, which is a bit
silly.
This changes the powerpc rtc-generic device to provide its
rtc_class_ops directly, to reduce the number of layers
by one.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Like zlib compression in pstore, this patch added lzo and lz4
compression support so that users can have more options and better
compression ratio.
The original code treats the compressed data together with the
uncompressed ECC correction notice by using zlib decompress. The
ECC correction notice is missing in the decompression process. The
treatment also makes lzo and lz4 not working. So I treat them
separately by using pstore_decompress() to treat the compressed
data, and memcpy() to treat the uncompressed ECC correction notice.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
If we do not provide the PVR for POWER8NVL, a guest on this system
currently ends up in PowerISA 2.06 compatibility mode on KVM, since QEMU
does not provide a generic PowerISA 2.07 mode yet. So some new
instructions from POWER8 (like "mtvsrd") get disabled for the guest,
resulting in crashes when using code compiled explicitly for
POWER8 (e.g. with the "-mcpu=power8" option of GCC).
Fixes: ddee09c099 ("powerpc: Add PVR for POWER8NVL processor")
Cc: stable@vger.kernel.org # v4.0+
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This will allow device drivers to consistently use io{read,write}XX
also for 64-bit accesses.
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
most architectures are relying on mmap_sem for write in their
arch_setup_additional_pages. If the waiting task gets killed by the oom
killer it would block oom_reaper from asynchronous address space reclaim
and reduce the chances of timely OOM resolving. Wait for the lock in
the killable mode and return with EINTR if the task got killed while
waiting.
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Andy Lutomirski <luto@amacapital.net> [x86 vdso]
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Define HAVE_EXIT_THREAD for archs which want to do something in
exit_thread. For others, let's define exit_thread as an empty inline.
This is a cleanup before we change the prototype of exit_thread to
accept a task parameter.
[akpm@linux-foundation.org: fix mips]
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chen Liqin <liqin.linux@gmail.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: David Howells <dhowells@redhat.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Highlights:
- Support for Power ISA 3.0 (Power9) Radix Tree MMU from Aneesh Kumar K.V
- Live patching support for ppc64le (also merged via livepatching.git)
Various cleanups & minor fixes from:
- Aaro Koskinen, Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V,
Chris Smart, Daniel Axtens, Frederic Barrat, Gavin Shan, Ian Munsie, Lennart
Sorensen, Madhavan Srinivasan, Mahesh Salgaonkar, Markus Elfring, Michael
Ellerman, Oliver O'Halloran, Paul Gortmaker, Paul Mackerras, Rashmica Gupta,
Russell Currey, Suraj Jitindar Singh, Thiago Jung Bauermann, Valentin
Rothberg, Vipin K Parashar.
General:
- Update LMB associativity index during DLPAR add/remove from Nathan Fontenot
- Fix branching to OOL handlers in relocatable kernel from Hari Bathini
- Add support for userspace Power9 copy/paste from Chris Smart
- Always use STRICT_MM_TYPECHECKS from Michael Ellerman
- Add mask of possible MMU features from Michael Ellerman
PCI:
- Enable pass through of NVLink to guests from Alexey Kardashevskiy
- Cleanups in preparation for powernv PCI hotplug from Gavin Shan
- Don't report error in eeh_pe_reset_and_recover() from Gavin Shan
- Restore initial state in eeh_pe_reset_and_recover() from Gavin Shan
- Revert "powerpc/eeh: Fix crash in eeh_add_device_early() on Cell" from Guilherme G. Piccoli
- Remove the dependency on EEH struct in DDW mechanism from Guilherme G. Piccoli
selftests:
- Test cp_abort during context switch from Chris Smart
- Add several tests for transactional memory support from Rashmica Gupta
perf:
- Add support for sampling interrupt register state from Anju T
- Add support for unwinding perf-stackdump from Chandan Kumar
cxl:
- Configure the PSL for two CAPI ports on POWER8NVL from Philippe Bergheaud
- Allow initialization on timebase sync failures from Frederic Barrat
- Increase timeout for detection of AFU mmio hang from Frederic Barrat
- Handle num_of_processes larger than can fit in the SPA from Ian Munsie
- Ensure PSL interrupt is configured for contexts with no AFU IRQs from Ian Munsie
- Add kernel API to allow a context to operate with relocate disabled from Ian Munsie
- Check periodically the coherent platform function's state from Christophe Lombard
Freescale:
- Updates from Scott: "Contains 86xx fixes, minor device tree fixes, an erratum
workaround, and a kconfig dependency fix."
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YvyQ
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights:
- Support for Power ISA 3.0 (Power9) Radix Tree MMU from Aneesh Kumar K.V
- Live patching support for ppc64le (also merged via livepatching.git)
Various cleanups & minor fixes from:
- Aaro Koskinen, Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V,
Chris Smart, Daniel Axtens, Frederic Barrat, Gavin Shan, Ian Munsie,
Lennart Sorensen, Madhavan Srinivasan, Mahesh Salgaonkar, Markus Elfring,
Michael Ellerman, Oliver O'Halloran, Paul Gortmaker, Paul Mackerras,
Rashmica Gupta, Russell Currey, Suraj Jitindar Singh, Thiago Jung
Bauermann, Valentin Rothberg, Vipin K Parashar.
General:
- Update LMB associativity index during DLPAR add/remove from Nathan
Fontenot
- Fix branching to OOL handlers in relocatable kernel from Hari Bathini
- Add support for userspace Power9 copy/paste from Chris Smart
- Always use STRICT_MM_TYPECHECKS from Michael Ellerman
- Add mask of possible MMU features from Michael Ellerman
PCI:
- Enable pass through of NVLink to guests from Alexey Kardashevskiy
- Cleanups in preparation for powernv PCI hotplug from Gavin Shan
- Don't report error in eeh_pe_reset_and_recover() from Gavin Shan
- Restore initial state in eeh_pe_reset_and_recover() from Gavin Shan
- Revert "powerpc/eeh: Fix crash in eeh_add_device_early() on Cell"
from Guilherme G Piccoli
- Remove the dependency on EEH struct in DDW mechanism from Guilherme
G Piccoli
selftests:
- Test cp_abort during context switch from Chris Smart
- Add several tests for transactional memory support from Rashmica
Gupta
perf:
- Add support for sampling interrupt register state from Anju T
- Add support for unwinding perf-stackdump from Chandan Kumar
cxl:
- Configure the PSL for two CAPI ports on POWER8NVL from Philippe
Bergheaud
- Allow initialization on timebase sync failures from Frederic Barrat
- Increase timeout for detection of AFU mmio hang from Frederic
Barrat
- Handle num_of_processes larger than can fit in the SPA from Ian
Munsie
- Ensure PSL interrupt is configured for contexts with no AFU IRQs
from Ian Munsie
- Add kernel API to allow a context to operate with relocate disabled
from Ian Munsie
- Check periodically the coherent platform function's state from
Christophe Lombard
Freescale:
- Updates from Scott: "Contains 86xx fixes, minor device tree fixes,
an erratum workaround, and a kconfig dependency fix."
* tag 'powerpc-4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (192 commits)
powerpc/86xx: Fix PCI interrupt map definition
powerpc/86xx: Move pci1 definition to the include file
powerpc/fsl: Fix build of the dtb embedded kernel images
powerpc/fsl: Fix rcpm compatible string
powerpc/fsl: Remove FSL_SOC dependency from FSL_LBC
powerpc/fsl-pci: Add a workaround for PCI 5 errata
powerpc/fsl: Fix SPI compatible on t208xrdb and t1040rdb
powerpc/powernv/npu: Add PE to PHB's list
powerpc/powernv: Fix insufficient memory allocation
powerpc/iommu: Remove the dependency on EEH struct in DDW mechanism
Revert "powerpc/eeh: Fix crash in eeh_add_device_early() on Cell"
powerpc/eeh: Drop unnecessary label in eeh_pe_change_owner()
powerpc/eeh: Ignore handlers in eeh_pe_reset_and_recover()
powerpc/eeh: Restore initial state in eeh_pe_reset_and_recover()
powerpc/eeh: Don't report error in eeh_pe_reset_and_recover()
Revert "powerpc/powernv: Exclude root bus in pnv_pci_reset_secondary_bus()"
powerpc/powernv/npu: Enable NVLink pass through
powerpc/powernv/npu: Rework TCE Kill handling
powerpc/powernv/npu: Add set/unset window helpers
powerpc/powernv/ioda2: Export debug helper pe_level_printk()
...
Pull livepatching updates from Jiri Kosina:
- remove of our own implementation of architecture-specific relocation
code and leveraging existing code in the module loader to perform
arch-dependent work, from Jessica Yu.
The relevant patches have been acked by Rusty (for module.c) and
Heiko (for s390).
- live patching support for ppc64le, which is a joint work of Michael
Ellerman and Torsten Duwe. This is coming from topic branch that is
share between livepatching.git and ppc tree.
- addition of livepatching documentation from Petr Mladek
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching:
livepatch: make object/func-walking helpers more robust
livepatch: Add some basic livepatch documentation
powerpc/livepatch: Add live patching support on ppc64le
powerpc/livepatch: Add livepatch stack to struct thread_info
powerpc/livepatch: Add livepatch header
livepatch: Allow architectures to specify an alternate ftrace location
ftrace: Make ftrace_location_range() global
livepatch: robustify klp_register_patch() API error checking
Documentation: livepatch: outline Elf format and requirements for patch modules
livepatch: reuse module loader code to write relocations
module: s390: keep mod_arch_specific for livepatch modules
module: preserve Elf information for livepatch modules
Elf: add livepatch-specific Elf constants
This reverts commit 89a51df5ab.
The function eeh_add_device_early() is used to perform EEH
initialization in devices added later on the system, like in
hotplug/DLPAR scenarios. Since the commit 89a51df5ab ("powerpc/eeh:
Fix crash in eeh_add_device_early() on Cell") a new check was introduced
in this function - Cell has no EEH capabilities which led to kernel oops
if hotplug was performed, so checking for eeh_enabled() was introduced
to avoid the issue.
However, in architectures that EEH is present like pSeries or PowerNV,
we might reach a case in which no PCI devices are present on boot time
and so EEH is not initialized. Then, if a device is added via DLPAR for
example, eeh_add_device_early() fails because eeh_enabled() is false,
and EEH end up not being enabled at all.
This reverts the aforementioned patch since a new verification was
introduced by the commit d91dafc02f ("powerpc/eeh: Delay probing EEH
device during hotplug") and so the original Cell issue does not happen
anymore.
Cc: stable@vger.kernel.org # v4.1+
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The label "reset" in eeh_pe_change_owner() is used only for once.
No need to keep it and just drop it. No logical changes introduced.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The function eeh_pe_reset_and_recover() is used to recover EEH
error when the passthrough device are transferred to guest and
backwards, meaning the device's driver is vfio-pci or none. In
both cases, the handlers triggered by eeh_report_reset() and
eeh_report_resume() shouldn't be called.
This ignores the error handlers from eeh_report_reset() and
eeh_report_resume().
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The function eeh_pe_reset_and_recover() is used to recover EEH
error when the passthrou device are transferred to guest and
backwards. The content in the device's config space will be lost
on PE reset issued in the middle of the recovery. The function
saves/restores it before/after the reset. However, config access
to some adapters like Broadcom BCM5719 at this point will causes
fenced PHB. The config space is always blocked and we save 0xFF's
that are restored at late point. The memory BARs are totally
corrupted, causing another EEH error upon access to one of the
memory BARs.
This restores the config space on those adapters like BCM5719
from the content saved to the EEH device when it's populated,
to resolve above issue.
Fixes: 5cfb20b9 ("powerpc/eeh: Emulate EEH recovery for VFIO devices")
Cc: stable@vger.kernel.org #v3.18+
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The function eeh_pe_reset_and_recover() is used to recover EEH
error when the passthrough device are transferred to guest and
backwards, meaning the device's driver is vfio-pci or none.
When the driver is vfio-pci that provides error_detected() error
handler only, the handler simply stops the guest and it's not
expected behaviour. On the other hand, no error handlers will
be called if we don't have a bound driver.
This ignores the error handler in eeh_pe_reset_and_recover()
that reports the error to device driver to avoid the exceptional
behaviour.
Fixes: 5cfb20b9 ("powerpc/eeh: Emulate EEH recovery for VFIO devices")
Cc: stable@vger.kernel.org #v3.18+
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In hotplug case, function pci_add_pci_devices() is called to rescan
the specified PCI bus, which might not have any child devices. Access
to the PCI bus's child device node will cause kernel crash without
exception.
This adds one more check to skip scanning PCI bus that doesn't have
any subordinate devices from device-tree, in order to avoid kernel
crash.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This renames traverse_pci_devices() to pci_traverse_device_nodes().
The function traverses all subordinate device nodes of the specified
one. Also, below cleanup applied to the function. No logical changes
introduced.
* Rename "pre" to "fn".
* Avoid assignment in if condition reported from checkpatch.pl.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This implements and exports pci_remove_device_node_info(). It's
used to remove the pdn (struct pci_dn) for the indicated device
node. The function is going to be used by PowerNV PCI hotplug
driver.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This renames update_dn_pci_info() to pci_add_device_node_info()
with corresponding adjustment on the parameter type and exports it.
The function is used to create pdn (struct pci_dn) for the indicated
device node. Another function add_pdn(), almost wrapper of
pci_add_device_node_info(), to be used in traverse_pci_devices(). No
logical changes introduced.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This moves pci_find_bus_by_node() from arch/powerpc/platforms/
pseries/pci_dlpar.c to arch/powerpc/kernel/pci-hotplug.c so that
the function can be used by pSeries and PowerNV platform at the
same time. Also, below cleanup applied. No functional changes
introduced.
* Remove variable "busdn" in find_bus_among_children()
* Use PCI_DN() to convert device node to pci_dn
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This renames pcibios_{add,remove}_pci_devices() to avoid conflicts
with names of the weak functions in PCI subsystem, which have the
prefix "pcibios". No logical changes introduced.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-By: Alistair Popple <alistair@popple.id.au>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The routine machine_check_pSeries_early() is only used on powernv, not
pseries. Hence rename machine_check_pSeries_early() to
machine_check_powernv_early().
Reported-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
After obtaining a property from of_find_property() and before calling
of_remove_property() most code checks to ensure that the property
returned from of_find_property() is not null. The previous patch moved
this check to the start of the function of_remove_property() in order to
avoid the case where this check isn't done and a null value is passed.
This ensures the check is always conducted before taking locks and
attempting to remove the property. Thus it is no longer necessary to
perform a check for null values before invoking of_remove_property().
Update of_remove_property() call sites in order to remove redundant
checking for null property value as check is now performed within the
of_remove_property function().
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
[mpe: Unbreak some lines which are just >80 chars for readability]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The code in machine_restart/power_off/halt() includes #ifdefs around
calls to smp_send_stop(), however these are not required as
include/linux/smp.h includes an empty version of this function for
CONFIG_SMP=n builds.
Signed-off-by: Chris Smart <chris@distroguy.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Support for the A2 cpu was removed in commit fb5a515704 ("powerpc:
Remove platforms/wsp and associated pieces"), and the externs:
__setup_cpu_a2 and __restore_cpu_a2 are still around and unused, so
remove them.
Signed-off-by: Rashmica Gupta <rashmicy@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We use the existing "ibm,pa-features" device-tree property to enable
Radix MMU mode. This means we default to hash mode unless firmware tells
us it's OK to start using Radix mode.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With 4K page size radix config our level 1 page table size is 64K and it
should be naturally aligned.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The vmalloc range differs between hash and radix config. Hence make
VMALLOC_START and related constants a variable which will be runtime
initialized depending on whether hash or radix mode is active.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[mpe: Fix missing init of ioremap_bot in pgtable_64.c for ppc64e]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We also use MMU_FTR_RADIX to branch out from code path specific to
hash.
No functionality change.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In order to enable symmetric hotplug, we must mirror the online &&
!active state of cpu-down on the cpu-up side.
However, to retain sanity, limit this state to per-cpu kthreads.
Aside from the change to set_cpus_allowed_ptr(), which allow moving
the per-cpu kthreads on, the other critical piece is the cpu selection
for pinned tasks in select_task_rq(). This avoids dropping into
select_fallback_rq().
select_fallback_rq() cannot be allowed to select !active cpus because
its used to migrate user tasks away. And we do not want to move user
tasks onto cpus that are in transition.
Requested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Jan H. Schönherr <jschoenh@amazon.de>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160301152303.GV6356@twins.programming.kicks-ass.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Core kernel doesn't track the page size of the VA range that we are
invalidating. Hence we end up flushing TLB for the entire mm here. Later
patches will improve this.
We also don't flush page walk cache separetly instead use RIC=2 when
flushing TLB, because we do a MMU gather flush after freeing page table.
MMU_NO_CONTEXT is updated for hash.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
How we switch MMU context differs between hash and radix. For hash we
need to switch the SLB details and for radix we need to switch the PID
SPR.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Radix and hash MMU models support different page table sizes. Make
the #defines a variable so that existing code can work with variable
sizes.
Slice related code is only used by hash, so use hash constants there. We
will replicate some of the boundary conditions with resepct to TASK_SIZE
using radix values too. Right now we do boundary condition check using
hash constants.
Swapper pgdir size is initialized in asm code. We select the max pgd
size to keep it simple. For now we select hash pgdir. When adding radix
we will switch that to radix pgdir which is 64K.
BUILD_BUG_ON check which is removed is already done in hugepage_init()
using MAYBE_BUILD_BUG_ON().
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use a helper instead of open coding with constants. A later patch will
drop the WIMG bits and use PowerISA 3.0 defines.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch fix spelling typos in printk from various part
of the codes.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In the ppc64 big endian ABI, function symbols point to function
descriptors. The symbols which point to the function entry points
have a dot in front of the function name. Consequently, when the
ftrace filter mechanism searches for the symbol corresponding to
an entry point address, it gets the dot symbol.
As a result, ftrace filter users have to be aware of this ABI detail on
ppc64 and prepend a dot to the function name when setting the filter.
The perf probe command insulates the user from this by ignoring the dot
in front of the symbol name when matching function names to symbols,
but the sysfs interface does not. This patch makes the ftrace filter
mechanism do the same when searching symbols.
Fixes the following failure in ftracetest's kprobe_ftrace.tc:
.../kprobe_ftrace.tc: line 9: echo: write error: Invalid argument
That failure is on this line of kprobe_ftrace.tc:
echo _do_fork > set_ftrace_filter
This is because there's no _do_fork entry in the functions list:
# cat available_filter_functions | grep _do_fork
._do_fork
This change introduces no regressions on the perf and ftracetest
testsuite results.
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The copy paste facility introduced in POWER9 provides an optimised
mechanism for a userspace application to copy a cacheline. This is
provided by a pair of instructions, copy and paste, while a third,
cp_abort (copy paste abort), provides a clean up of the state in case of
a failure.
The copy instruction will read a 128 byte cacheline and store it in an
internal buffer. The subsequent paste instruction will store this
internal buffer to memory and set a CR field if the paste succeeds.
Since the state of the copy paste buffer is internal (and not
architecturally visible), in the unlikely event of a context switch, the
state cannot be stored and the paste should therefore fail.
The cp_abort instruction exists to fail and clean up any such
interrupted copy paste sequence and is to be called by the kernel as
part of the context switch. Doing so prevents data from a preceding copy
in one process leaking into the paste of another.
This code enables use of the cp_abort instruction if a supported
processor is detected.
NOTE: this is for userspace only, not in kernel, and does not deal
with KVM guests.
Patch created with much assistance from Michael Neuling
<mikey@neuling.org>
Signed-off-by: Chris Smart <chris@distroguy.com>
Reviewed-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Found by smatch.
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The __end_handlers marker was intended to mark down upto code that gets
called from exception prologs. But that hasn't kept pace with code
changes. Case in point, slb_miss_realmode being called from exception
prolog code but isn't below __end_handlers marker. So, __end_handlers
marker is as good as a comment but could be misleading at times if it
isn't in sync with the code, as is the case now. So, let us avoid this
confusion by having a better comment and removing __end_handlers marker
altogether.
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Some of the interrupt vectors on 64-bit POWER server processors are only
32 bytes long (8 instructions), which is not enough for the full
first-level interrupt handler. For these we need to branch to an
out-of-line (OOL) handler. But when we are running a relocatable kernel,
interrupt vectors till __end_interrupts marker are copied down to real
address 0x100. So, branching to labels (ie. OOL handlers) outside this
section must be handled differently (see LOAD_HANDLER()), considering
relocatable kernel, which would need at least 4 instructions.
However, branching from interrupt vector means that we corrupt the
CFAR (come-from address register) on POWER7 and later processors as
mentioned in commit 1707dd16. So, EXCEPTION_PROLOG_0 (6 instructions)
that contains the part up to the point where the CFAR is saved in the
PACA should be part of the short interrupt vectors before we branch out
to OOL handlers.
But as mentioned already, there are interrupt vectors on 64-bit POWER
server processors that are only 32 bytes long (like vectors 0x4f00,
0x4f20, etc.), which cannot accomodate the above two cases at the same
time owing to space constraint. Currently, in these interrupt vectors,
we simply branch out to OOL handlers, without using LOAD_HANDLER(),
which leaves us vulnerable when running a relocatable kernel (eg. kdump
case). While this has been the case for sometime now and kdump is used
widely, we were fortunate not to see any problems so far, for three
reasons:
1. In almost all cases, production kernel (relocatable) is used for
kdump as well, which would mean that crashed kernel's OOL handler
would be at the same place where we end up branching to, from short
interrupt vector of kdump kernel.
2. Also, OOL handler was unlikely the reason for crash in almost all
the kdump scenarios, which meant we had a sane OOL handler from
crashed kernel that we branched to.
3. On most 64-bit POWER server processors, page size is large enough
that marking interrupt vector code as executable (see commit
429d2e83) leads to marking OOL handler code from crashed kernel,
that sits right below interrupt vector code from kdump kernel, as
executable as well.
Let us fix this by moving the __end_interrupts marker down past OOL
handlers to make sure that we also copy OOL handlers to real address
0x100 when running a relocatable kernel.
This fix has been tested successfully in kdump scenario, on an LPAR with
4K page size by using different default/production kernel and kdump
kernel.
Also tested by manually corrupting the OOL handlers in the first kernel
and then kdump'ing, and then causing the OOL handlers to fire - mpe.
Fixes: c1fb6816fb ("powerpc: Add relocation on exception vector handlers")
Cc: stable@vger.kernel.org
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We need to update the user TM feature bits (PPC_FEATURE2_HTM and
PPC_FEATURE2_HTM) to mirror what we do with the kernel TM feature
bit.
At the moment, if firmware reports TM is not available we turn off
the kernel TM feature bit but leave the userspace ones on. Userspace
thinks it can execute TM instructions and it dies trying.
This (together with a QEMU patch) fixes PR KVM, which doesn't currently
support TM.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
scan_features() updates cpu_user_features but not cpu_user_features2.
Amongst other things, cpu_user_features2 contains the user TM feature
bits which we must keep in sync with the kernel TM feature bit.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The REAL_LE feature entry in the ibm_pa_feature struct is missing an MMU
feature value, meaning all the remaining elements initialise the wrong
values.
This means instead of checking for byte 5, bit 0, we check for byte 0,
bit 0, and then we incorrectly set the CPU feature bit as well as MMU
feature bit 1 and CPU user feature bits 0 and 2 (5).
Checking byte 0 bit 0 (IBM numbering), means we're looking at the
"Memory Management Unit (MMU)" feature - ie. does the CPU have an MMU.
In practice that bit is set on all platforms which have the property.
This means we set CPU_FTR_REAL_LE always. In practice that seems not to
matter because all the modern cpus which have this property also
implement REAL_LE, and we've never needed to disable it.
We're also incorrectly setting MMU feature bit 1, which is:
#define MMU_FTR_TYPE_8xx 0x00000002
Luckily the only place that looks for MMU_FTR_TYPE_8xx is in Book3E
code, which can't run on the same cpus as scan_features(). So this also
doesn't matter in practice.
Finally in the CPU user feature mask, we're setting bits 0 and 2. Bit 2
is not currently used, and bit 0 is:
#define PPC_FEATURE_PPC_LE 0x00000001
Which says the CPU supports the old style "PPC Little Endian" mode.
Again this should be harmless in practice as no 64-bit CPUs implement
that mode.
Fix the code by adding the missing initialisation of the MMU feature.
Also add a comment marking CPU user feature bit 2 (0x4) as reserved. It
would be unsafe to start using it as old kernels incorrectly set it.
Fixes: 44ae3ab335 ("powerpc: Free up some CPU feature bits by moving out MMU-related features")
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
[mpe: Flesh out changelog, add comment reserving 0x4]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add the kconfig logic & assembly support for handling live patched
functions. This depends on DYNAMIC_FTRACE_WITH_REGS, which in turn
depends on the new -mprofile-kernel ftrace ABI, which is only supported
currently on ppc64le.
Live patching is handled by a special ftrace handler. This means it runs
from ftrace_caller(). The live patch handler modifies the NIP so as to
redirect the return from ftrace_caller() to the new patched function.
However there is one particularly tricky case we need to handle.
If a function A calls another function B, and it is known at link time
that they share the same TOC, then A will not save or restore its TOC,
and will call the local entry point of B.
When we live patch B, we replace it with a new function C, which may
not have the same TOC as A. At live patch time it's too late to modify A
to do the TOC save/restore, so the live patching code must interpose
itself between A and C, and do the TOC save/restore that A omitted.
An additionaly complication is that the livepatch code can not create a
stack frame in order to save the TOC. That is because if C takes > 8
arguments, or is varargs, A will have written the arguments for C in
A's stack frame.
To solve this, we introduce a "livepatch stack" which grows upward from
the base of the regular stack, and is used to store the TOC & LR when
calling a live patched function.
When the patched function returns, we retrieve the real LR & TOC from
the livepatch stack, restore them, and pop the livepatch "stack frame".
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Torsten Duwe <duwe@suse.de>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
In order to support live patching we need to maintain an alternate
stack of TOC & LR values. We use the base of the stack for this, and
store the "live patch stack pointer" in struct thread_info.
Unlike the other fields of thread_info, we can not statically initialise
that value, so it must be done at run time.
This patch just adds the code to support that, it is not enabled until
the next patch which actually adds live patch support.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Sometimes when sparse warns about undefined symbols, it isn't
because they should have 'static' added, it's because they're
overriding __weak symbols defined elsewhere, and the header has
been missed.
Fix a few of them by adding appropriate headers.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As sparse suggests, these should be made static.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The Makefile/Kconfig currently controlling compilation of this code is:
obj-$(CONFIG_PPC64) += setup_64.o sys_ppc32.o \
signal_64.o ptrace32.o \
paca.o nvram_64.o firmware.o
arch/powerpc/platforms/Kconfig.cputype:config PPC64
arch/powerpc/platforms/Kconfig.cputype: bool "64-bit kernel"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We don't replace module.h with init.h since the file already has that.
We delete the MODULE_LICENSE tag since that information is already
contained at the top of the file in the comments.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Hari Bathini <hbathini@linux.vnet.ibm.com>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
IBM online documentation for EEH uses "extended error handling" and
"enhanced error handling" to refer to the same thing, in different
places. The only place mentioning it as "enhanced error handling" in the
kernel is the MAINTAINERS file, and it's "extended" in some documentation.
IBM originally defined EEH as "enhanced error handling", so standardise
all mentions of EEH to use that term.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We have a bunch of SLB related code in the tree which is there to handle
dynamic VSIDs - but currently it's all disabled at compile time. The
comments say "Keep that around for when we re-implement dynamic VSIDs".
But that was over 10 years ago (commit 3c726f8dee ("[PATCH] ppc64:
support 64k pages")). The chance that it would still work unchanged is
minimal, and in the meantime it's confusing to folks browsing/grepping
the code. If we ever want to re-instate it, it's in the git history.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Balbir Singh <bsingharora@gmail.com>
In save_sprs() in process.c contains the following test:
if (cpu_has_feature(cpu_has_feature(CPU_FTR_ALTIVEC)))
t->vrsave = mfspr(SPRN_VRSAVE);
CPU feature with the mask 0x1 is CPU_FTR_COHERENT_ICACHE so the test
is equivilent to:
if (cpu_has_feature(CPU_FTR_ALTIVEC) &&
cpu_has_feature(CPU_FTR_COHERENT_ICACHE))
On CPUs without support for both (i.e G5) this results in vrsave not
being saved between context switches. The vector register save/restore
code doesn't use VRSAVE to determine which registers to save/restore,
but the value of VRSAVE is used to determine if altivec is being used
in several code paths.
Fixes: 152d523e63 ("powerpc: Create context switch helpers save_sprs() and restore_sprs()")
Cc: stable@vger.kernel.org
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
KASAN needs to know whether the allocation happens in an IRQ handler.
This lets us strip everything below the IRQ entry point to reduce the
number of unique stack traces needed to be stored.
Move the definition of __irq_entry to <linux/interrupt.h> so that the
users don't need to pull in <linux/ftrace.h>. Also introduce the
__softirq_entry macro which is similar to __irq_entry, but puts the
corresponding functions to the .softirqentry.text section.
Signed-off-by: Alexander Potapenko <glider@google.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Andrey Konovalov <adech.fo@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Konstantin Serebryany <kcc@google.com>
Cc: Dmitry Chernenkov <dmitryc@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Highlights:
- Restructure Linux PTE on Book3S/64 to Radix format from Paul Mackerras
- Book3s 64 MMU cleanup in preparation for Radix MMU from Aneesh Kumar K.V
- Add POWER9 cputable entry from Michael Neuling
- FPU/Altivec/VSX save/restore optimisations from Cyril Bur
- Add support for new ftrace ABI on ppc64le from Torsten Duwe
Various cleanups & minor fixes from:
- Adam Buchbinder, Andrew Donnellan, Balbir Singh, Christophe Leroy, Cyril
Bur, Luis Henriques, Madhavan Srinivasan, Pan Xinhui, Russell Currey,
Sukadev Bhattiprolu, Suraj Jitindar Singh.
General:
- atomics: Allow architectures to define their own __atomic_op_* helpers from
Boqun Feng
- Implement atomic{, 64}_*_return_* variants and acquire/release/relaxed
variants for (cmp)xchg from Boqun Feng
- Add powernv_defconfig from Jeremy Kerr
- Fix BUG_ON() reporting in real mode from Balbir Singh
- Add xmon command to dump OPAL msglog from Andrew Donnellan
- Add xmon command to dump process/task similar to ps(1) from Douglas Miller
- Clean up memory hotplug failure paths from David Gibson
pci/eeh:
- Redesign SR-IOV on PowerNV to give absolute isolation between VFs from Wei
Yang.
- EEH Support for SRIOV VFs from Wei Yang and Gavin Shan.
- PCI/IOV: Rename and export virtfn_{add, remove} from Wei Yang
- PCI: Add pcibios_bus_add_device() weak function from Wei Yang
- MAINTAINERS: Update EEH details and maintainership from Russell Currey
cxl:
- Support added to the CXL driver for running on both bare-metal and
hypervisor systems, from Christophe Lombard and Frederic Barrat.
- Ignore probes for virtual afu pci devices from Vaibhav Jain
perf:
- Export Power8 generic and cache events to sysfs from Sukadev Bhattiprolu
- hv-24x7: Fix usage with chip events, display change in counter values,
display domain indices in sysfs, eliminate domain suffix in event names,
from Sukadev Bhattiprolu
Freescale:
- Updates from Scott: "Highlights include 8xx optimizations, 32-bit checksum
optimizations, 86xx consolidation, e5500/e6500 cpu hotplug, more fman and
other dt bits, and minor fixes/cleanup."
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qkAt
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"This was delayed a day or two by some build-breakage on old toolchains
which we've now fixed.
There's two PCI commits both acked by Bjorn.
There's one commit to mm/hugepage.c which is (co)authored by Kirill.
Highlights:
- Restructure Linux PTE on Book3S/64 to Radix format from Paul
Mackerras
- Book3s 64 MMU cleanup in preparation for Radix MMU from Aneesh
Kumar K.V
- Add POWER9 cputable entry from Michael Neuling
- FPU/Altivec/VSX save/restore optimisations from Cyril Bur
- Add support for new ftrace ABI on ppc64le from Torsten Duwe
Various cleanups & minor fixes from:
- Adam Buchbinder, Andrew Donnellan, Balbir Singh, Christophe Leroy,
Cyril Bur, Luis Henriques, Madhavan Srinivasan, Pan Xinhui, Russell
Currey, Sukadev Bhattiprolu, Suraj Jitindar Singh.
General:
- atomics: Allow architectures to define their own __atomic_op_*
helpers from Boqun Feng
- Implement atomic{, 64}_*_return_* variants and acquire/release/
relaxed variants for (cmp)xchg from Boqun Feng
- Add powernv_defconfig from Jeremy Kerr
- Fix BUG_ON() reporting in real mode from Balbir Singh
- Add xmon command to dump OPAL msglog from Andrew Donnellan
- Add xmon command to dump process/task similar to ps(1) from Douglas
Miller
- Clean up memory hotplug failure paths from David Gibson
pci/eeh:
- Redesign SR-IOV on PowerNV to give absolute isolation between VFs
from Wei Yang.
- EEH Support for SRIOV VFs from Wei Yang and Gavin Shan.
- PCI/IOV: Rename and export virtfn_{add, remove} from Wei Yang
- PCI: Add pcibios_bus_add_device() weak function from Wei Yang
- MAINTAINERS: Update EEH details and maintainership from Russell
Currey
cxl:
- Support added to the CXL driver for running on both bare-metal and
hypervisor systems, from Christophe Lombard and Frederic Barrat.
- Ignore probes for virtual afu pci devices from Vaibhav Jain
perf:
- Export Power8 generic and cache events to sysfs from Sukadev
Bhattiprolu
- hv-24x7: Fix usage with chip events, display change in counter
values, display domain indices in sysfs, eliminate domain suffix in
event names, from Sukadev Bhattiprolu
Freescale:
- Updates from Scott: "Highlights include 8xx optimizations, 32-bit
checksum optimizations, 86xx consolidation, e5500/e6500 cpu
hotplug, more fman and other dt bits, and minor fixes/cleanup"
* tag 'powerpc-4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (179 commits)
powerpc: Fix unrecoverable SLB miss during restore_math()
powerpc/8xx: Fix do_mtspr_cpu6() build on older compilers
powerpc/rcpm: Fix build break when SMP=n
powerpc/book3e-64: Use hardcoded mttmr opcode
powerpc/fsl/dts: Add "jedec,spi-nor" flash compatible
powerpc/T104xRDB: add tdm riser card node to device tree
powerpc32: PAGE_EXEC required for inittext
powerpc/mpc85xx: Add pcsphy nodes to FManV3 device tree
powerpc/mpc85xx: Add MDIO bus muxing support to the board device tree(s)
powerpc/86xx: Introduce and use common dtsi
powerpc/86xx: Update device tree
powerpc/86xx: Move dts files to fsl directory
powerpc/86xx: Switch to kconfig fragments approach
powerpc/86xx: Update defconfigs
powerpc/86xx: Consolidate common platform code
powerpc32: Remove one insn in mulhdu
powerpc32: small optimisation in flush_icache_range()
powerpc: Simplify test in __dma_sync()
powerpc32: move xxxxx_dcache_range() functions inline
powerpc32: Remove clear_pages() and define clear_page() inline
...
This changes several users of manual "on"/"off" parsing to use
strtobool.
Some side-effects:
- these uses will now parse y/n/1/0 meaningfully too
- the early_param uses will now bubble up parse errors
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Amitkumar Karwar <akarwar@marvell.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Joe Perches <joe@perches.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Nishant Sarmukadam <nishants@marvell.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Steve French <sfrench@samba.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We can disable debug_pagealloc processing even if the code is compiled
with CONFIG_DEBUG_PAGEALLOC. This patch changes the code to query
whether it is enabled or not in runtime.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
but lots of architecture-specific changes.
* ARM:
- VHE support so that we can run the kernel at EL2 on ARMv8.1 systems
- PMU support for guests
- 32bit world switch rewritten in C
- various optimizations to the vgic save/restore code.
* PPC:
- enabled KVM-VFIO integration ("VFIO device")
- optimizations to speed up IPIs between vcpus
- in-kernel handling of IOMMU hypercalls
- support for dynamic DMA windows (DDW).
* s390:
- provide the floating point registers via sync regs;
- separated instruction vs. data accesses
- dirty log improvements for huge guests
- bugfixes and documentation improvements.
* x86:
- Hyper-V VMBus hypercall userspace exit
- alternative implementation of lowest-priority interrupts using vector
hashing (for better VT-d posted interrupt support)
- fixed guest debugging with nested virtualizations
- improved interrupt tracking in the in-kernel IOAPIC
- generic infrastructure for tracking writes to guest memory---currently
its only use is to speedup the legacy shadow paging (pre-EPT) case, but
in the future it will be used for virtual GPUs as well
- much cleanup (LAPIC, kvmclock, MMU, PIT), including ubsan fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJW5r3BAAoJEL/70l94x66D2pMH/jTSWWwdTUJMctrDjPVzKzG0
yOzHW5vSLFoFlwEOY2VpslnXzn5TUVmCAfrdmFNmQcSw6hGb3K/xA/ZX/KLwWhyb
oZpr123ycahga+3q/ht/dFUBCCyWeIVMdsLSFwpobEBzPL0pMgc9joLgdUC6UpWX
tmN0LoCAeS7spC4TTiTTpw3gZ/L+aB0B6CXhOMjldb9q/2CsgaGyoVvKA199nk9o
Ngu7ImDt7l/x1VJX4/6E/17VHuwqAdUrrnbqerB/2oJ5ixsZsHMGzxQ3sHCmvyJx
WG5L00ubB1oAJAs9fBg58Y/MdiWX99XqFhdEfxq4foZEiQuCyxygVvq3JwZTxII=
=OUZZ
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"One of the largest releases for KVM... Hardly any generic
changes, but lots of architecture-specific updates.
ARM:
- VHE support so that we can run the kernel at EL2 on ARMv8.1 systems
- PMU support for guests
- 32bit world switch rewritten in C
- various optimizations to the vgic save/restore code.
PPC:
- enabled KVM-VFIO integration ("VFIO device")
- optimizations to speed up IPIs between vcpus
- in-kernel handling of IOMMU hypercalls
- support for dynamic DMA windows (DDW).
s390:
- provide the floating point registers via sync regs;
- separated instruction vs. data accesses
- dirty log improvements for huge guests
- bugfixes and documentation improvements.
x86:
- Hyper-V VMBus hypercall userspace exit
- alternative implementation of lowest-priority interrupts using
vector hashing (for better VT-d posted interrupt support)
- fixed guest debugging with nested virtualizations
- improved interrupt tracking in the in-kernel IOAPIC
- generic infrastructure for tracking writes to guest
memory - currently its only use is to speedup the legacy shadow
paging (pre-EPT) case, but in the future it will be used for
virtual GPUs as well
- much cleanup (LAPIC, kvmclock, MMU, PIT), including ubsan fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (217 commits)
KVM: x86: remove eager_fpu field of struct kvm_vcpu_arch
KVM: x86: disable MPX if host did not enable MPX XSAVE features
arm64: KVM: vgic-v3: Only wipe LRs on vcpu exit
arm64: KVM: vgic-v3: Reset LRs at boot time
arm64: KVM: vgic-v3: Do not save an LR known to be empty
arm64: KVM: vgic-v3: Save maintenance interrupt state only if required
arm64: KVM: vgic-v3: Avoid accessing ICH registers
KVM: arm/arm64: vgic-v2: Make GICD_SGIR quicker to hit
KVM: arm/arm64: vgic-v2: Only wipe LRs on vcpu exit
KVM: arm/arm64: vgic-v2: Reset LRs at boot time
KVM: arm/arm64: vgic-v2: Do not save an LR known to be empty
KVM: arm/arm64: vgic-v2: Move GICH_ELRSR saving to its own function
KVM: arm/arm64: vgic-v2: Save maintenance interrupt state only if required
KVM: arm/arm64: vgic-v2: Avoid accessing GICH registers
KVM: s390: allocate only one DMA page per VM
KVM: s390: enable STFLE interpretation only if enabled for the guest
KVM: s390: wake up when the VCPU cpu timer expires
KVM: s390: step the VCPU timer while in enabled wait
KVM: s390: protect VCPU cpu timer with a seqcount
KVM: s390: step VCPU cpu timer during kvm_run ioctl
...
Commit 70fe3d9 "powerpc: Restore FPU/VEC/VSX if previously used" introduces a
call to restore_math() late in the syscall return path, after MSR_RI has been
cleared. The MSR_RI flag is used to indicate whether the kernel can take
another exception or not. A cleared MSR_RI flag indicates that the kernel
cannot.
Unfortunately when a machine is under SLB pressure an SLB miss can occur
in restore_math() which (with MSR_RI cleared) leads to an unrecoverable
exception.
Unrecoverable exception 4100 at c0000000000088d8
cpu 0x0: Vector: 4100 at [c0000003fa473b20]
pc: c0000000000088d8: .load_vr_state+0x70/0x110
lr: c00000000000f710: .restore_math+0x130/0x188
sp: c0000003fa473da0
msr: 9000000002003030
current = 0xc0000007f876f180
paca = 0xc00000000fff0000 softe: 0 irq_happened: 0x01
pid = 1944, comm = K08umountfs
[link register ] c00000000000f710 .restore_math+0x130/0x188
[c0000003fa473da0] c0000003fa473e30 (unreliable)
[c0000003fa473e30] c000000000007b6c system_call+0x84/0xfc
The clearing of MSR_RI is actually an optimisation to avoid multiple MSR
writes, what must be disabled are interrupts. See comment in entry_64.S:
/*
* For performance reasons we clear RI the same time that we
* clear EE. We only need to clear RI just before we restore r13
* below, but batching it with EE saves us one expensive mtmsrd call.
* We have to be careful to restore RI if we branch anywhere from
* here (eg syscall_exit_work).
*/
At the point of calling restore_math() r13 has not been restored, as such, the
quick fix of turning MSR_RI back on for the call to restore_math() will
eliminate the occurrence of an unrecoverable exception.
We'd like to do a better fix in future.
Fixes: 70fe3d980f ("powerpc: Restore FPU/VEC/VSX if previously used")
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This preserves the ability to build using older binutils (reportedly <=
2.22).
Fixes: 6becef7ea0 ("powerpc/mpc85xx: Add CPU hotplug support for E6500")
Signed-off-by: Scott Wood <oss@buserror.net>
Cc: chenhui.zhao@freescale.com
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull cpu hotplug updates from Thomas Gleixner:
"This is the first part of the ongoing cpu hotplug rework:
- Initial implementation of the state machine
- Runs all online and prepare down callbacks on the plugged cpu and
not on some random processor
- Replaces busy loop waiting with completions
- Adds tracepoints so the states can be followed"
More detailed commentary on this work from an earlier email:
"What's wrong with the current cpu hotplug infrastructure?
- Asymmetry
The hotplug notifier mechanism is asymmetric versus the bringup and
teardown. This is mostly caused by the notifier mechanism.
- Largely undocumented dependencies
While some notifiers use explicitely defined notifier priorities,
we have quite some notifiers which use numerical priorities to
express dependencies without any documentation why.
- Control processor driven
Most of the bringup/teardown of a cpu is driven by a control
processor. While it is understandable, that preperatory steps,
like idle thread creation, memory allocation for and initialization
of essential facilities needs to be done before a cpu can boot,
there is no reason why everything else must run on a control
processor. Before this patch series, bringup looks like this:
Control CPU Booting CPU
do preparatory steps
kick cpu into life
do low level init
sync with booting cpu sync with control cpu
bring the rest up
- All or nothing approach
There is no way to do partial bringups. That's something which is
really desired because we waste e.g. at boot substantial amount of
time just busy waiting that the cpu comes to life. That's stupid
as we could very well do preparatory steps and the initial IPI for
other cpus and then go back and do the necessary low level
synchronization with the freshly booted cpu.
- Minimal debuggability
Due to the notifier based design, it's impossible to switch between
two stages of the bringup/teardown back and forth in order to test
the correctness. So in many hotplug notifiers the cancel
mechanisms are either not existant or completely untested.
- Notifier [un]registering is tedious
To [un]register notifiers we need to protect against hotplug at
every callsite. There is no mechanism that bringup/teardown
callbacks are issued on the online cpus, so every caller needs to
do it itself. That also includes error rollback.
What's the new design?
The base of the new design is a symmetric state machine, where both
the control processor and the booting/dying cpu execute a well
defined set of states. Each state is symmetric in the end, except
for some well defined exceptions, and the bringup/teardown can be
stopped and reversed at almost all states.
So the bringup of a cpu will look like this in the future:
Control CPU Booting CPU
do preparatory steps
kick cpu into life
do low level init
sync with booting cpu sync with control cpu
bring itself up
The synchronization step does not require the control cpu to wait.
That mechanism can be done asynchronously via a worker or some
other mechanism.
The teardown can be made very similar, so that the dying cpu cleans
up and brings itself down. Cleanups which need to be done after
the cpu is gone, can be scheduled asynchronously as well.
There is a long way to this, as we need to refactor the notion when a
cpu is available. Today we set the cpu online right after it comes
out of the low level bringup, which is not really correct.
The proper mechanism is to set it to available, i.e. cpu local
threads, like softirqd, hotplug thread etc. can be scheduled on that
cpu, and once it finished all booting steps, it's set to online, so
general workloads can be scheduled on it. The reverse happens on
teardown. First thing to do is to forbid scheduling of general
workloads, then teardown all the per cpu resources and finally shut it
off completely.
This patch series implements the basic infrastructure for this at the
core level. This includes the following:
- Basic state machine implementation with well defined states, so
ordering and prioritization can be expressed.
- Interfaces to [un]register state callbacks
This invokes the bringup/teardown callback on all online cpus with
the proper protection in place and [un]installs the callbacks in
the state machine array.
For callbacks which have no particular ordering requirement we have
a dynamic state space, so that drivers don't have to register an
explicit hotplug state.
If a callback fails, the code automatically does a rollback to the
previous state.
- Sysfs interface to drive the state machine to a particular step.
This is only partially functional today. Full functionality and
therefor testability will be achieved once we converted all
existing hotplug notifiers over to the new scheme.
- Run all CPU_ONLINE/DOWN_PREPARE notifiers on the booting/dying
processor:
Control CPU Booting CPU
do preparatory steps
kick cpu into life
do low level init
sync with booting cpu sync with control cpu
wait for boot
bring itself up
Signal completion to control cpu
In a previous step of this work we've done a full tree mechanical
conversion of all hotplug notifiers to the new scheme. The balance
is a net removal of about 4000 lines of code.
This is not included in this series, as we decided to take a
different approach. Instead of mechanically converting everything
over, we will do a proper overhaul of the usage sites one by one so
they nicely fit into the symmetric callback scheme.
I decided to do that after I looked at the ugliness of some of the
converted sites and figured out that their hotplug mechanism is
completely buggered anyway. So there is no point to do a
mechanical conversion first as we need to go through the usage
sites one by one again in order to achieve a full symmetric and
testable behaviour"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
cpu/hotplug: Document states better
cpu/hotplug: Fix smpboot thread ordering
cpu/hotplug: Remove redundant state check
cpu/hotplug: Plug death reporting race
rcu: Make CPU_DYING_IDLE an explicit call
cpu/hotplug: Make wait for dead cpu completion based
cpu/hotplug: Let upcoming cpu bring itself fully up
arch/hotplug: Call into idle with a proper state
cpu/hotplug: Move online calls to hotplugged cpu
cpu/hotplug: Create hotplug threads
cpu/hotplug: Split out the state walk into functions
cpu/hotplug: Unpark smpboot threads from the state machine
cpu/hotplug: Move scheduler cpu_online notifier to hotplug core
cpu/hotplug: Implement setup/removal interface
cpu/hotplug: Make target state writeable
cpu/hotplug: Add sysfs state interface
cpu/hotplug: Hand in target state to _cpu_up/down
cpu/hotplug: Convert the hotplugged cpu work to a state machine
cpu/hotplug: Convert to a state machine for the control processor
cpu/hotplug: Add tracepoints
...
Freescale updates from Scott:
"Highlights include 8xx optimizations, 32-bit checksum optimizations,
86xx consolidation, e5500/e6500 cpu hotplug, more fman and other dt
bits, and minor fixes/cleanup."
Inlining of _dcache_range() functions has shown that the compiler
does the same thing a bit better with one insn less
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
flush/clean/invalidate _dcache_range() functions are all very
similar and are quite short. They are mainly used in __dma_sync()
perf_event locate them in the top 3 consumming functions during
heavy ethernet activity
They are good candidate for inlining, as __dma_sync() does
almost nothing but calling them
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
clear_pages() is never used expect by clear_page, and PPC32 is the
only architecture (still) having this function. Neither PPC64 nor
any other architecture has it.
This patch removes clear_pages() and moves clear_page() function
inline (same as PPC64) as it only is a few isns
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
On PPC8xx, flushing instruction cache is performed by writing
in register SPRN_IC_CST. This registers suffers CPU6 ERRATA.
The patch rewrites the fonction in C so that CPU6 ERRATA will
be handled transparently
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
There is no real need to have set_context() in assembly.
Now that we have mtspr() handling CPU6 ERRATA directly, we
can rewrite set_context() in C language for easier maintenance.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
CPU6 ERRATA is now handled directly in mtspr(), so we can use the
standard set_dec() fonction in all cases.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
On a live running system (VoIP gateway for Air Trafic Control), over
a 10 minutes period (with 277s idle), we get 87 millions DTLB misses
and approximatly 35 secondes are spent in DTLB handler.
This represents 5.8% of the overall time and even 10.8% of the
non-idle time.
Among those 87 millions DTLB misses, 15% are on user addresses and
85% are on kernel addresses. And within the kernel addresses, 93%
are on addresses from the linear address space and only 7% are on
addresses from the virtual address space.
MPC8xx has no BATs but it has 8Mb page size. This patch implements
mapping of kernel RAM using 8Mb pages, on the same model as what is
done on the 40x.
In 4k pages mode, each PGD entry maps a 4Mb area: we map every two
entries to the same 8Mb physical page. In each second entry, we add
4Mb to the page physical address to ease life of the FixupDAR
routine. This is just ignored by HW.
In 16k pages mode, each PGD entry maps a 64Mb area: each PGD entry
will point to the first page of the area. The DTLB handler adds
the 3 bits from EPN to map the correct page.
With this patch applied, we now get only 13 millions TLB misses
during the 10 minutes period. The idle time has increased to 313s
and the overall time spent in DTLB miss handler is 6.3s, which
represents 1% of the overall time and 2.2% of non-idle time.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
We are spending between 40 and 160 cycles with a mean of 65 cycles in
the DTLB handling routine (measured with mftbl) so make it more
simple althought it adds one instruction.
With this modification, we get three registers available at all time,
which will help with following patch.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
Merge the ftrace changes to support -mprofile-kernel on ppc64le. This is
a prerequisite for live patching, the support for which will be merged
via the livepatch tree based on this topic branch.
When CONFIG_DEBUG_PAGEALLOC is activated, the initial TLB mapping gets
flushed to track accesses to wrong areas. Therefore, kernel addresses
will also generate ITLB misses.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
- VHE support so that we can run the kernel at EL2 on ARMv8.1 systems
- PMU support for guests
- 32bit world switch rewritten in C
- Various optimizations to the vgic save/restore code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=rpvb
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/ARM updates for 4.6
- VHE support so that we can run the kernel at EL2 on ARMv8.1 systems
- PMU support for guests
- 32bit world switch rewritten in C
- Various optimizations to the vgic save/restore code
Conflicts:
include/uapi/linux/kvm.h
In eeh_pci_enable(), after making the request to set the new options, we
call eeh_ops->wait_state() to check that the request finished successfully.
At the moment, if eeh_ops->wait_state() returns 0, we return 0 without
checking that it reflects the expected outcome. This can lead to callers
further up the chain incorrectly assuming the slot has been successfully
unfrozen and continuing to attempt recovery.
On powernv, this will occur if pnv_eeh_get_pe_state() or
pnv_eeh_get_phb_state() return 0, which in turn occurs if the relevant OPAL
call returns OPAL_EEH_STOPPED_MMIO_DMA_FREEZE or
OPAL_EEH_PHB_ERROR respectively.
On pseries, this will occur if pseries_eeh_get_state() returns 0, which in
turn occurs if RTAS reports that the PE is in the MMIO Stopped and DMA
Stopped states.
Obviously, none of these cases represent a successful completion of a
request to thaw MMIO or DMA.
Fix the check so that a wait_state() return value of 0 won't be considered
successful for the EEH_OPT_THAW_MMIO or EEH_OPT_THAW_DMA cases.
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When eeh_dump_pe_log() is only called by eeh_slot_error_detail(),
we already have the check that the PE isn't in PCI config blocked
state in eeh_slot_error_detail(). So we needn't the duplicated
check in eeh_dump_pe_log().
This removes the duplicated check in eeh_dump_pe_log(). No logical
changes introduced.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When passing through SRIOV VFs to guest, we possibly encounter EEH
error on PF. In this case, the VF PEs are put into frozen state.
The error could be reported to guest before it's captured by the
host. That means the guest could attempt to recover errors on VFs
before host gets chance to recover errors on PFs. The VFs won't be
recovered successfully.
This enforces the recovery order for above case: the recovery on
child PE in guest is hold until the recovery on parent PE in host
is completed.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When we have partial hotplug as part of the error recovery on PF,
the VFs that are bound with vfio-pci driver will experience hotplug.
That's not allowed.
This checks if the VF PE is passed or not. If it does, we leave
the VF without removing it.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When EEH error happened to the parent PE of those PEs that have
been passed through to guest, the error is propagated to guest
domain and the VFIO driver's error handlers are called. It's not
correct as the error in the host domain shouldn't be propagated
to guests and affect them.
This adds one more limitation when calling EEH error handlers.
If the PE has been passed through to guest, the error handlers
won't be called.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PFs are enumerated on PCI bus, while VFs are created by PF's driver.
In EEH recovery, it has two cases:
1. Device and driver is EEH aware, error handlers are called.
2. Device and driver is not EEH aware, un-plug the device and plug it again
by enumerating it.
The special thing happens on the second case. For a PF, we could use the
original pci core to enumerate the bus, while for VF we need to record the
VFs which aer un-plugged then plug it again.
Also The patch caches the VF index in pci_dn, which can be used to
calculate VF's bus, device and function number. Those information helps to
locate the VF's PCI device instance when doing hotplug during EEH recovery
if necessary.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PEs for VFs don't have primary bus. So they have to have their own reset
backend, which is used during EEH recovery. The patch implements the reset
backend for VF's PE by issuing FLR or AF FLR to the VFs, which are contained
in the PE.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This creates PEs for VFs in the weak function pcibios_bus_add_device().
Those PEs for VFs are identified with newly introduced flag EEH_PE_VF
so that we treat them differently during EEH recovery.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
VFs and their corresponding pdn are created and released dynamically
when their PF's SRIOV capability is enabled and disabled. This creates
and releases EEH devices for VFs when creating and releasing their pdn
instances, which means EEH devices and pdn instances have same life
cycle. Also, VF's EEH device is identified by (struct eeh_dev::physfn).
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This restricts the EEH address cache to use only the first 7 BARs. This
makes __eeh_addr_cache_insert_dev() ignore PCI bridge window and IOV BARs.
As the result of this change, eeh_addr_cache_get_dev() will return VFs from
VF's resource addresses instead of parent PFs.
This also removes PCI bridge check as we limit __eeh_addr_cache_insert_dev()
to 7 BARs and this effectively excludes PCI bridges from being cached.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As commit ac205b7bb7 ("PCI: make sriov work with hotplug remove")
indicates, VFs which is on the same PCI bus as their PF, should be
removed before the PF. Otherwise, we might run into kernel crash
at PCI unplugging time.
This applies the above pattern to powerpc PCI hotplug path.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The original implementation is ugly: unnecessary if statements and
"out" tag. This reworks the function to avoid above weaknesses. No
functional changes introduced.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The gcc switch -mprofile-kernel defines a new ABI for calling _mcount()
very early in the function with minimal overhead.
Although mprofile-kernel has been available since GCC 3.4, there were
bugs which were only fixed recently. Currently it is known to work in
GCC 4.9, 5 and 6.
Additionally there are two possible code sequences generated by the
flag, the first uses mflr/std/bl and the second is optimised to omit the
std. Currently only gcc 6 has the optimised sequence. This patch
supports both sequences.
Initial work started by Vojtech Pavlik, used with permission.
Key changes:
- rework _mcount() to work for both the old and new ABIs.
- implement new versions of ftrace_caller() and ftrace_graph_caller()
which deal with the new ABI.
- updates to __ftrace_make_nop() to recognise the new mcount calling
sequence.
- updates to __ftrace_make_call() to recognise the nop'ed sequence.
- implement ftrace_modify_call().
- updates to the module loader to surpress the toc save in the module
stub when calling mcount with the new ABI.
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Torsten Duwe <duwe@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Rather than open-coding -pg whereever we want to disable ftrace, use the
existing $(CC_FLAGS_FTRACE) variable.
This has the advantage that it will work in future when we use a
different set of flags to enable ftrace.
Signed-off-by: Torsten Duwe <duwe@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Convert powerpc's arch_ftrace_update_code() from its own version to use
the generic default functionality (without stop_machine -- our
instructions are properly aligned and the replacements atomic).
With this we gain error checking and the much-needed function_trace_op
handling.
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Reviewed-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Torsten Duwe <duwe@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In order to support the new -mprofile-kernel ABI, we need to be able to
call from the module back to ftrace_caller() (in the kernel) without
using the module's r2. That is because the function in this module which
is calling ftrace_caller() may not have setup r2, if it doesn't
otherwise need it (ie. it accesses no globals).
To make that work we add a new stub which is used for calling
ftrace_caller(), which uses the kernel toc instead of the module toc.
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Reviewed-by: Torsten Duwe <duwe@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When a module is loaded, calls out to the kernel go via a stub which is
generated at runtime. One of these stubs is used to call _mcount(),
which is the default target of tracing calls generated by the compiler
with -pg.
If dynamic ftrace is enabled (which it typically is), another stub is
used to call ftrace_caller(), which is the target of tracing calls when
ftrace is actually active.
ftrace then wants to disable the calls to _mcount() at module startup,
and enable/disable the calls to ftrace_caller() when enabling/disabling
tracing - all of these it does by patching the code.
As part of that code patching, the ftrace code wants to confirm that the
branch it is about to modify, is in fact a call to a module stub which
calls _mcount() or ftrace_caller().
Currently it does that by inspecting the instructions and confirming
they are what it expects. Although that works, the code to do it is
pretty intricate because it requires lots of knowledge about the exact
format of the stub.
We can make that process easier by marking the generated stubs with a
magic value, and then looking for that magic value. Altough this is not
as rigorous as the current method, I believe it is sufficient in
practice.
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Reviewed-by: Torsten Duwe <duwe@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently we generate the module stub for ftrace_caller() at the bottom
of apply_relocate_add(). However apply_relocate_add() is potentially
called more than once per module, which means we will try to generate
the ftrace_caller() stub multiple times.
Although the current code deals with that correctly, ie. it only
generates a stub the first time, it would be clearer to only try to
generate the stub once.
Note also on first reading it may appear that we generate a different
stub for each section that requires relocation, but that is not the
case. The code in stub_for_addr() that searches for an existing stub
uses sechdrs[me->arch.stubs_section], ie. the single stub section for
this module.
A cleaner approach is to only generate the ftrace_caller() stub once,
from module_finalize(). Although the original code didn't check to see
if the stub was actually generated correctly, it seems prudent to add a
check, so do that. And an additional benefit is we can clean the ifdefs
up a little.
Finally we must propagate the const'ness of some of the pointers passed
to module_finalize(), but that is also an improvement.
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Reviewed-by: Torsten Duwe <duwe@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move the logic to work out the kernel toc pointer into a header. This is
a good cleanup, and also means we can use it elsewhere in future.
Reviewed-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Reviewed-by: Torsten Duwe <duwe@suse.de>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Tested-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Support Freescale E6500 core-based platforms, like t4240.
Support disabling/enabling individual CPU thread dynamically.
Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com>
Freescale E500MC and E5500 core-based platforms, like P4080, T1040,
support disabling/enabling CPU dynamically.
This patch adds this feature on those platforms.
Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com>
Signed-off-by: Tang Yuantian <Yuantian.Tang@feescale.com>
[scottwood: removed unused pr_fmt]
Signed-off-by: Scott Wood <oss@buserror.net>
There is a RCPM (Run Control/Power Management) in Freescale QorIQ
series processors. The device performs tasks associated with device
run control and power management.
The driver implements some features: mask/unmask irq, enter/exit low
power states, freeze time base, etc.
Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com>
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
[scottwood: remove __KERNEL__ ifdef]
Signed-off-by: Scott Wood <oss@buserror.net>
Various e500 core have different cache architecture, so they
need different cache flush operations. Therefore, add a callback
function cpu_flush_caches to the struct cpu_spec. The cache flush
operation for the specific kind of e500 is selected at init time.
The callback function will flush all caches inside the current cpu.
Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com>
Signed-off-by: Tang Yuantian <Yuantian.Tang@feescale.com>
Signed-off-by: Scott Wood <oss@buserror.net>
When destroying a hw_breakpoint event, the kernel oopses as follows:
Unable to handle kernel paging request for data at address 0x00000c07
NIP [c0000000000291d0] arch_unregister_hw_breakpoint+0x40/0x60
LR [c00000000020b6b4] release_bp_slot+0x44/0x80
Call chain:
hw_breakpoint_event_init()
bp->destroy = bp_perf_event_destroy;
do_exit()
perf_event_exit_task()
perf_event_exit_task_context()
WRITE_ONCE(child_ctx->task, TASK_TOMBSTONE);
perf_event_exit_event()
free_event()
_free_event()
bp_perf_event_destroy() // event->destroy(event);
release_bp_slot()
arch_unregister_hw_breakpoint()
perf_event_exit_task_context() sets child_ctx->task as TASK_TOMBSTONE
which is (void *)-1. arch_unregister_hw_breakpoint() tries to fetch
'thread' attribute of 'task' resulting in oops.
Peterz points out that the code shouldn't be using bp->ctx anyway, but
fixing that will require a decent amount of rework. So for now to fix
the oops, check if bp->ctx->task has been set to (void *)-1, before
dereferencing it. We don't use TASK_TOMBSTONE, because that would
require exporting it and it's supposed to be an internal detail.
Fixes: 63b6da39bb ("perf: Fix perf_event_exit_task() race")
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds the ability to be able to save the VSX registers to the
thread struct without giving up (disabling the facility) next time the
process returns to userspace.
This patch builds on a previous optimisation for the FPU and VEC registers
in the thread copy path to avoid a possibly pointless reload of VSX state.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds the ability to be able to save the VEC registers to the
thread struct without giving up (disabling the facility) next time the
process returns to userspace.
This patch builds on a previous optimisation for the FPU registers in the
thread copy path to avoid a possibly pointless reload of VEC state.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds the ability to be able to save the FPU registers to the
thread struct without giving up (disabling the facility) next time the
process returns to userspace.
This patch optimises the thread copy path (as a result of a fork() or
clone()) so that the parent thread can return to userspace with hot
registers avoiding a possibly pointless reload of FPU register state.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This prepares for the decoupling of saving {fpu,altivec,vsx} registers and
marking {fpu,altivec,vsx} as being unused by a thread.
Currently giveup_{fpu,altivec,vsx}() does both however optimisations to
task switching can be made if these two operations are decoupled.
save_all() will permit the saving of registers to thread structs and leave
threads MSR with bits enabled.
This patch introduces no functional change.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently the FPU, VEC and VSX facilities are lazily loaded. This is not
a problem unless a process is using these facilities.
Modern versions of GCC are very good at automatically vectorising code,
new and modernised workloads make use of floating point and vector
facilities, even the kernel makes use of vectorised memcpy.
All this combined greatly increases the cost of a syscall since the
kernel uses the facilities sometimes even in syscall fast-path making it
increasingly common for a thread to take an *_unavailable exception soon
after a syscall, not to mention potentially taking all three.
The obvious overcompensation to this problem is to simply always load
all the facilities on every exit to userspace. Loading up all FPU, VEC
and VSX registers every time can be expensive and if a workload does
avoid using them, it should not be forced to incur this penalty.
An 8bit counter is used to detect if the registers have been used in the
past and the registers are always loaded until the value wraps to back
to zero.
Several versions of the assembly in entry_64.S were tested:
1. Always calling C.
2. Performing a common case check and then calling C.
3. A complex check in asm.
After some benchmarking it was determined that avoiding C in the common
case is a performance benefit (option 2). The full check in asm (option
3) greatly complicated that codepath for a negligible performance gain
and the trade-off was deemed not worth it.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
[mpe: Move load_vec in the struct to fill an existing hole, reword change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
fixup
Currently when threads get scheduled off they always giveup the FPU,
Altivec (VMX) and Vector (VSX) units if they were using them. When they are
scheduled back on a fault is then taken to enable each facility and load
registers. As a result explicitly disabling FPU/VMX/VSX has not been
necessary.
Future changes and optimisations remove this mandatory giveup and fault
which could cause calls such as clone() and fork() to copy threads and run
them later with FPU/VMX/VSX enabled but no registers loaded.
This patch starts the process of having MSR_{FP,VEC,VSX} mean that a
threads registers are hot while not having MSR_{FP,VEC,VSX} means that the
registers must be loaded. This allows for a smarter return to userspace.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Let the non boot cpus call into idle with the corresponding hotplug state, so
the hotplug core can handle the further bringup. That's a first step to
convert the boot side of the hotplugged cpus to do all the synchronization
with the other side through the state machine. For now it'll only start the
hotplug thread and kick the full bringup of the cpu.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: Rik van Riel <riel@redhat.com>
Cc: Rafael Wysocki <rafael.j.wysocki@intel.com>
Cc: "Srivatsa S. Bhat" <srivatsa@mit.edu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Turner <pjt@google.com>
Link: http://lkml.kernel.org/r/20160226182341.614102639@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adds support to real-mode KVM to search for a core
running in the host partition and send it an IPI message with
VCPU to be woken. This avoids having to switch to the host
partition to complete an H_IPI hypercall when the VCPU which
is the target of the the H_IPI is not loaded (is not running
in the guest).
The patch also includes the support in the IPI handler running
in the host to do the wakeup by calling kvmppc_xics_ipi_action
for the PPC_MSG_RM_HOST_ACTION message.
When a guest is being destroyed, we need to ensure that there
are no pending IPIs waiting to wake up a VCPU before we free
the VCPUs of the guest. This is accomplished by:
- Forces a PPC_MSG_CALL_FUNCTION IPI to be completed by all CPUs
before freeing any VCPUs in kvm_arch_destroy_vm().
- Any PPC_MSG_RM_HOST_ACTION messages must be executed first
before any other PPC_MSG_CALL_FUNCTION messages.
Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
smp_muxed_ipi_message_pass() invokes smp_ops->cause_ipi, which
uses an ioremapped address to access registers on the XICS
interrupt controller to cause the IPI. Because of this real
mode callers cannot call smp_muxed_ipi_message_pass() for IPI
messaging.
This patch creates a separate function smp_muxed_ipi_set_message
just to set the IPI message without the cause_ipi routine.
After calling this function to set the IPI message, real
mode callers must cause the IPI by writing to the XICS registers
directly.
As part of this, we also change smp_muxed_ipi_message_pass
to call smp_muxed_ipi_set_message to set the message instead
of doing it directly inside the routine.
Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch increases the number of demuxed messages for a
controller with a single ipi to 8 for 64-bit systems.
This is required because we want to use the IPI mechanism
to send messages from a CPU running in KVM real mode in a
guest to a CPU in the host to take some action. Currently,
we only support 4 messages and all 4 are already taken.
Define a fifth message PPC_MSG_RM_HOST_ACTION for this
purpose.
Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Replace calls to get_random_int() followed by a cast to (unsigned long)
with calls to get_random_long(). Also address shifting bug which, in
case of x86 removed entropy mask for mmap_rnd_bits values > 31 bits.
Signed-off-by: Daniel Cashman <dcashman@android.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: David S. Miller <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Nick Kralevich <nnk@google.com>
Cc: Jeff Vander Stoep <jeffv@google.com>
Cc: Mark Salyzyn <salyzyn@android.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- eeh: Fix partial hotplug criterion from Gavin Shan
- mm: Clear the invalid slot information correctly from Aneesh Kumar K.V
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=bk3U
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.5-4' into next
Pull in our current fixes from 4.5, in particular the "Fix Multi hit
ERAT" bug is causing folks some grief when testing next.
I ran into this issue while debugging an early boot problem. The system
hit a BUG_ON() but report bug failed to print the line number and file
name. The reason being that the system was running in real mode and
report_bug() searches for addresses in the PAGE_OFFSET+ region.
Suggested-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a cputable entry for POWER9. More code is required to actually
boot and run on a POWER9 but this gets the base piece in which we can
start building on.
Copies over from POWER8 except for:
- Adds a new CPU_FTR_ARCH_300 bit to start hanging new architecture
features from (in subsequent patches).
- Advertises new user features bits PPC_FEATURE2_ARCH_3_00 &
HAS_IEEE128 when on POWER9.
- Drops CPU_FTR_SUBCORE.
- Drops PMU code and machine check.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use defines for literals __init_tlb_power[78] rather than hand coding
them.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
During error recovery, the device could be removed as part of the
partial hotplug. The criterion used to come with partial hotplug
is: if the device driver provides error_detected(), slot_reset()
and resume() callbacks, it's immune from hotplug. Otherwise,
it's going to experience partial hotplug during EEH recovery. But
the criterion isn't correct enough: mlx4_core driver for Mellanox
adapters provides error_detected(), slot_reset() callbacks, but
resume() isn't there. Those Mellanox adapters won't be to involved
in the partial hotplug.
This fixes the criterion to a practical one: adpater with driver
that provides error_detected(), slot_reset() will be immune from
partial hotplug. resume() isn't mandatory.
Fixes: f2da4ccf ("powerpc/eeh: More relaxed hotplug criterion")
Cc: stable@vger.kernel.org #v4.4+
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- Fix build error on 32-bit with checkpoint restart from Aneesh Kumar
- Fix dedotify for binutils >= 2.26 from Andreas Schwab
- Don't trace hcalls on offline CPUs from Denis Kirjanov
- eeh: Fix stale cached primary bus from Gavin Shan
- eeh: Fix stale PE primary bus from Gavin Shan
- mm: Fix Multi hit ERAT cause by recent THP update from Aneesh Kumar K.V
- ioda: Set "read" permission when "write" is set from Alexey Kardashevskiy
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7Yzi
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.5-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix build error on 32-bit with checkpoint restart from Aneesh Kumar
- Fix dedotify for binutils >= 2.26 from Andreas Schwab
- Don't trace hcalls on offline CPUs from Denis Kirjanov
- eeh: Fix stale cached primary bus from Gavin Shan
- eeh: Fix stale PE primary bus from Gavin Shan
- mm: Fix Multi hit ERAT cause by recent THP update from Aneesh Kumar K.V
- ioda: Set "read" permission when "write" is set from Alexey Kardashevskiy
* tag 'powerpc-4.5-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/ioda: Set "read" permission when "write" is set
powerpc/mm: Fix Multi hit ERAT cause by recent THP update
powerpc/powernv: Fix stale PE primary bus
powerpc/eeh: Fix stale cached primary bus
powerpc/pseries: Don't trace hcalls on offline CPUs
powerpc: Fix dedotify for binutils >= 2.26
powerpc/book3s_32: Fix build error with checkpoint restart
I spent some time trying to use kgdb and debugged my inability to
resume from kgdb_handle_breakpoint(). NIP is not incremented
and that leads to a loop in the debugger.
I've tested this lightly on a virtual instance with KDB enabled.
After the patch, I am able to get the "go" command to work as
expected.
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When PE is created, its primary bus is cached to pe->bus. At later
point, the cached primary bus is returned from eeh_pe_bus_get().
However, we could get stale cached primary bus and run into kernel
crash in one case: full hotplug as part of fenced PHB error recovery
releases all PCI busses under the PHB at unplugging time and recreate
them at plugging time. pe->bus is still dereferencing the PCI bus
that was released.
This adds another PE flag (EEH_PE_PRI_BUS) to represent the validity
of pe->bus. pe->bus is updated when its first child EEH device is
online and the flag is set. Before unplugging in full hotplug for
error recovery, the flag is cleared.
Fixes: 8cdb2833 ("powerpc/eeh: Trace PCI bus from PE")
Cc: stable@vger.kernel.org #v3.11+
Reported-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reported-by: Pradipta Ghosh <pradghos@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Tested-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Lockdep is initialized at compile time now. Get rid of lockdep_init().
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Krinkin <krinkin.m.u@gmail.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: mm-commits@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The comment block above pcibios_set_pcie_reset_state() incorrectly refers
to pcibios_set_pcie_slot_reset(). Fix the comment accordingly.
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since binutils 2.26 BFD is doing suffix merging on STRTAB sections. But
dedotify modifies the symbol names in place, which can also modify
unrelated symbols with a name that matches a suffix of a dotted name. To
remove the leading dot of a symbol name we can just increment the pointer
into the STRTAB section instead.
Backport to all stables to avoid breakage when people update their
binutils - mpe.
Cc: stable@vger.kernel.org
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- Wire up copy_file_range() syscall from Chandan Rajendra
- Simplify module TOC handling from Alan Modra
- Remove newly added extra definition of pmd_dirty from Stephen Rothwell
- Allow user space to map rtas_rmo_buf from Vasant Hegde
- Fix PE location code from Gavin Shan
- Remove PPMU_HAS_SSLOT flag for Power8 from Madhavan Srinivasan
- Fixup _HPAGE_CHG_MASK from Aneesh Kumar K.V
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=KZ85
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Wire up copy_file_range() syscall from Chandan Rajendra
- Simplify module TOC handling from Alan Modra
- Remove newly added extra definition of pmd_dirty from Stephen Rothwell
- Allow user space to map rtas_rmo_buf from Vasant Hegde
- Fix PE location code from Gavin Shan
- Remove PPMU_HAS_SSLOT flag for Power8 from Madhavan Srinivasan
- Fixup _HPAGE_CHG_MASK from Aneesh Kumar K.V
* tag 'powerpc-4.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mm: Fixup _HPAGE_CHG_MASK
powerpc/perf: Remove PPMU_HAS_SSLOT flag for Power8
powerpc/eeh: Fix PE location code
powerpc/mm: Allow user space to map rtas_rmo_buf
powerpc: Remove newly added extra definition of pmd_dirty
powerpc: Simplify module TOC handling
powerpc: Wire up copy_file_range() syscall
In eeh_pe_loc_get(), the PE location code is retrieved from the
"ibm,loc-code" property of the device node for the bridge of the
PE's primary bus. It's not correct because the property indicates
the parent PE's location code.
This reads the correct PE location code from "ibm,io-base-loc-code"
or "ibm,slot-location-code" property of PE parent bus's device node.
Cc: stable@vger.kernel.org # v3.16+
Fixes: 357b2f3dd9 ("powerpc/eeh: Dump PE location code")
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Tested-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Merge third patch-bomb from Andrew Morton:
"I'm pretty much done for -rc1 now:
- the rest of MM, basically
- lib/ updates
- checkpatch, epoll, hfs, fatfs, ptrace, coredump, exit
- cpu_mask simplifications
- kexec, rapidio, MAINTAINERS etc, etc.
- more dma-mapping cleanups/simplifications from hch"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (109 commits)
MAINTAINERS: add/fix git URLs for various subsystems
mm: memcontrol: add "sock" to cgroup2 memory.stat
mm: memcontrol: basic memory statistics in cgroup2 memory controller
mm: memcontrol: do not uncharge old page in page cache replacement
Documentation: cgroup: add memory.swap.{current,max} description
mm: free swap cache aggressively if memcg swap is full
mm: vmscan: do not scan anon pages if memcg swap limit is hit
swap.h: move memcg related stuff to the end of the file
mm: memcontrol: replace mem_cgroup_lruvec_online with mem_cgroup_online
mm: vmscan: pass memcg to get_scan_count()
mm: memcontrol: charge swap to cgroup2
mm: memcontrol: clean up alloc, online, offline, free functions
mm: memcontrol: flatten struct cg_proto
mm: memcontrol: rein in the CONFIG space madness
net: drop tcp_memcontrol.c
mm: memcontrol: introduce CONFIG_MEMCG_LEGACY_KMEM
mm: memcontrol: allow to disable kmem accounting for cgroup2
mm: memcontrol: account "kmem" consumers in cgroup2 memory controller
mm: memcontrol: move kmem accounting code to CONFIG_MEMCG
mm: memcontrol: separate kmem code from legacy tcp accounting code
...
PowerPC64 uses the symbol .TOC. much as other targets use
_GLOBAL_OFFSET_TABLE_. It identifies the value of the GOT pointer (or in
powerpc parlance, the TOC pointer). Global offset tables are generally
local to an executable or shared library, or in the kernel, module. Thus
it does not make sense for a module to resolve a relocation against
.TOC. to the kernel's .TOC. value. A module has its own .TOC., and
indeed the powerpc64 module relocation processing ignores the kernel
value of .TOC. and instead calculates a module-local value.
This patch removes code involved in exporting the kernel .TOC., tweaks
modpost to ignore an undefined .TOC., and the module loader to twiddle
the section symbol so that .TOC. isn't seen as undefined.
Note that if the kernel was compiled with -msingle-pic-base then ELFv2
would not have function global entry code setting up r2. In that case
the module call stubs would need to be modified to set up r2 using the
kernel .TOC. value, requiring some of this code to be reinstated.
mpe: Furthermore a change in binutils master (not yet released) causes
the current way we handle the TOC to no longer work when building with
MODVERSIONS=y and RELOCATABLE=n. The symptom is that modules can not be
loaded due to there being no version found for TOC.
Cc: stable@vger.kernel.org # 3.16+
Signed-off-by: Alan Modra <amodra@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This hooks up UBSAN support for PowerPC.
So far it's found some interesting cases where we don't properly sanitise
input to shifts, including one in our futex handling. Nothing critical,
but interesting and worth fixing.
[valentinrothberg@gmail.com: arch/powerpc/Kconfig: fix typo in select statement]
Signed-off-by: Daniel Axtens <dja@axtens.net>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The four cpumasks cpu_{possible,online,present,active}_bits are exposed
readonly via the corresponding const variables cpu_xyz_mask. But they are
also accessible for arbitrary writing via the exposed functions
set_cpu_xyz. There's quite a bit of code throughout the kernel which
iterates over or otherwise accesses these bitmaps, and having the access
go via the cpu_xyz_mask variables is nowadays [1] simply a useless
indirection.
It may be that any problem in CS can be solved by an extra level of
indirection, but that doesn't mean every extra indirection solves a
problem. In this case, it even necessitates some minor ugliness (see
4/6).
Patch 1/6 is new in v2, and fixes a build failure on ppc by renaming a
struct member, to avoid problems when the identifier cpu_online_mask
becomes a macro later in the series. The next four patches eliminate the
cpu_xyz_mask variables by simply exposing the actual bitmaps, after
renaming them to discourage direct access - that still happens through
cpu_xyz_mask, which are now simply macros with the same type and value as
they used to have.
After that, there's no longer any reason to have the setter functions be
out-of-line: The boolean parameter is almost always a literal true or
false, so by making them static inlines they will usually compile to one
or two instructions.
For a defconfig build on x86_64, bloat-o-meter says we save ~3000 bytes.
We also save a little stack (stackdelta says 127 functions have a 16 byte
smaller stack frame, while two grow by that amount). Mostly because, when
iterating over the mask, gcc typically loads the value of cpu_xyz_mask
into a callee-saved register and from there into %rdi before each
find_next_bit call - now it can just load the appropriate immediate
address into %rdi before each call.
[1] See Rusty's kind explanation
http://thread.gmane.org/gmane.linux.kernel/2047078/focus=2047722 for
some historic context.
This patch (of 6):
As preparation for eliminating the indirect access to the various global
cpu_*_bits bitmaps via the pointer variables cpu_*_mask, rename the
cpu_online_mask member of struct fadump_crash_info_header to simply
online_mask, thus allowing cpu_online_mask to become a macro.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Ground work for the new Power9 MMU from Aneesh Kumar K.V
- Optimise FP/VMX/VSX context switching from Anton Blanchard
- Various cleanups from Krzysztof Kozlowski, John Ogness, Rashmica Gupta,
Russell Currey, Gavin Shan, Daniel Axtens, Michael Neuling, Andrew Donnellan
- Allow wrapper to work on non-english system from Laurent Vivier
- Add rN aliases to the pt_regs_offset table from Rashmica Gupta
- Fix module autoload for rackmeter & axonram drivers from Luis de Bethencourt
- Include KVM guest test in all interrupt vectors from Paul Mackerras
- Fix DSCR inheritance over fork() from Anton Blanchard
- Make value-returning atomics & {cmp}xchg* & their atomic_ versions fully ordered from Boqun Feng
- Print MSR TM bits in oops messages from Michael Neuling
- Add TM signal return & invalid stack selftests from Michael Neuling
- Limit EPOW reset event warnings from Vipin K Parashar
- Remove the Cell QPACE code from Rashmica Gupta
- Append linux_banner to exception information in xmon from Rashmica Gupta
- Add selftest to check if VSRs are corrupted from Rashmica Gupta
- Remove broken GregorianDay() from Daniel Axtens
- Import Anton's context_switch2 benchmark into selftests from Michael Ellerman
- Add selftest script to test HMI functionality from Daniel Axtens
- Remove obsolete OPAL v2 support from Stewart Smith
- Make enter_rtas() private from Michael Ellerman
- PPR exception cleanups from Michael Ellerman
- Add page soft dirty tracking from Laurent Dufour
- Add support for Nvlink NPUs from Alistair Popple
- Add support for kexec on 476fpe from Alistair Popple
- Enable kernel CPU dlpar from sysfs from Nathan Fontenot
- Copy only required pieces of the mm_context_t to the paca from Michael Neuling
- Add a kmsg_dumper that flushes OPAL console output on panic from Russell Currey
- Implement save_stack_trace_regs() to enable kprobe stack tracing from Steven Rostedt
- Add HWCAP bits for Power9 from Michael Ellerman
- Fix _PAGE_PTE breaking swapoff from Aneesh Kumar K.V
- Fix _PAGE_SWP_SOFT_DIRTY breaking swapoff from Hugh Dickins
- scripts/recordmcount.pl: support data in text section on powerpc from Ulrich Weigand
- Handle R_PPC64_ENTRY relocations in modules from Ulrich Weigand
- cxl: Fix possible idr warning when contexts are released from Vaibhav Jain
- cxl: use correct operator when writing pcie config space values from Andrew Donnellan
- cxl: Fix DSI misses when the context owning task exits from Vaibhav Jain
- cxl: fix build for GCC 4.6.x from Brian Norris
- cxl: use -Werror only with CONFIG_PPC_WERROR from Brian Norris
- cxl: Enable PCI device ID for future IBM CXL adapter from Uma Krishnan
- Freescale updates from Scott: Highlights include moving QE code out of
arch/powerpc (to be shared with arm), device tree updates, and minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=R5bX
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Core:
- Ground work for the new Power9 MMU from Aneesh Kumar K.V
- Optimise FP/VMX/VSX context switching from Anton Blanchard
Misc:
- Various cleanups from Krzysztof Kozlowski, John Ogness, Rashmica
Gupta, Russell Currey, Gavin Shan, Daniel Axtens, Michael Neuling,
Andrew Donnellan
- Allow wrapper to work on non-english system from Laurent Vivier
- Add rN aliases to the pt_regs_offset table from Rashmica Gupta
- Fix module autoload for rackmeter & axonram drivers from Luis de
Bethencourt
- Include KVM guest test in all interrupt vectors from Paul Mackerras
- Fix DSCR inheritance over fork() from Anton Blanchard
- Make value-returning atomics & {cmp}xchg* & their atomic_ versions
fully ordered from Boqun Feng
- Print MSR TM bits in oops messages from Michael Neuling
- Add TM signal return & invalid stack selftests from Michael Neuling
- Limit EPOW reset event warnings from Vipin K Parashar
- Remove the Cell QPACE code from Rashmica Gupta
- Append linux_banner to exception information in xmon from Rashmica
Gupta
- Add selftest to check if VSRs are corrupted from Rashmica Gupta
- Remove broken GregorianDay() from Daniel Axtens
- Import Anton's context_switch2 benchmark into selftests from
Michael Ellerman
- Add selftest script to test HMI functionality from Daniel Axtens
- Remove obsolete OPAL v2 support from Stewart Smith
- Make enter_rtas() private from Michael Ellerman
- PPR exception cleanups from Michael Ellerman
- Add page soft dirty tracking from Laurent Dufour
- Add support for Nvlink NPUs from Alistair Popple
- Add support for kexec on 476fpe from Alistair Popple
- Enable kernel CPU dlpar from sysfs from Nathan Fontenot
- Copy only required pieces of the mm_context_t to the paca from
Michael Neuling
- Add a kmsg_dumper that flushes OPAL console output on panic from
Russell Currey
- Implement save_stack_trace_regs() to enable kprobe stack tracing
from Steven Rostedt
- Add HWCAP bits for Power9 from Michael Ellerman
- Fix _PAGE_PTE breaking swapoff from Aneesh Kumar K.V
- Fix _PAGE_SWP_SOFT_DIRTY breaking swapoff from Hugh Dickins
- scripts/recordmcount.pl: support data in text section on powerpc
from Ulrich Weigand
- Handle R_PPC64_ENTRY relocations in modules from Ulrich Weigand
cxl:
- cxl: Fix possible idr warning when contexts are released from
Vaibhav Jain
- cxl: use correct operator when writing pcie config space values
from Andrew Donnellan
- cxl: Fix DSI misses when the context owning task exits from Vaibhav
Jain
- cxl: fix build for GCC 4.6.x from Brian Norris
- cxl: use -Werror only with CONFIG_PPC_WERROR from Brian Norris
- cxl: Enable PCI device ID for future IBM CXL adapter from Uma
Krishnan
Freescale:
- Freescale updates from Scott: Highlights include moving QE code out
of arch/powerpc (to be shared with arm), device tree updates, and
minor fixes"
* tag 'powerpc-4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (149 commits)
powerpc/module: Handle R_PPC64_ENTRY relocations
scripts/recordmcount.pl: support data in text section on powerpc
powerpc/powernv: Fix OPAL_CONSOLE_FLUSH prototype and usages
powerpc/mm: fix _PAGE_SWP_SOFT_DIRTY breaking swapoff
powerpc/mm: Fix _PAGE_PTE breaking swapoff
cxl: Enable PCI device ID for future IBM CXL adapter
cxl: use -Werror only with CONFIG_PPC_WERROR
cxl: fix build for GCC 4.6.x
powerpc: Add HWCAP bits for Power9
powerpc/powernv: Reserve PE#0 on NPU
powerpc/powernv: Change NPU PE# assignment
powerpc/powernv: Fix update of NVLink DMA mask
powerpc/powernv: Remove misleading comment in pci.c
powerpc: Implement save_stack_trace_regs() to enable kprobe stack tracing
powerpc: Fix build break due to paca mm_context_t changes
cxl: Fix DSI misses when the context owning task exits
MAINTAINERS: Update Scott Wood's e-mail address
powerpc/powernv: Fix minor off-by-one error in opal_mce_check_early_recovery()
powerpc: Fix style of self-test config prompts
powerpc/powernv: Only delay opal_rtc_read() retry when necessary
...
Pull livepatching updates from Jiri Kosina:
- RO/NX attribute fixes for patch module relocations from Josh
Poimboeuf. As part of this effort, module.c has been cleaned up as
well and livepatching is piggy-backing on this cleanup. Rusty is OK
with this whole lot going through livepatching tree.
- symbol disambiguation support from Chris J Arges. That series is
also
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
but this came in only after I've alredy pushed out. Didn't want to
rebase because of that, hence I am mentioning it here.
- symbol lookup fix from Miroslav Benes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching:
livepatch: Cleanup module page permission changes
module: keep percpu symbols in module's symtab
module: clean up RO/NX handling.
module: use a structure to encapsulate layout.
gcov: use within_module() helper.
module: Use the same logic for setting and unsetting RO/NX
livepatch: function,sympos scheme in livepatch sysfs directory
livepatch: add sympos as disambiguator field to klp_reloc
livepatch: add old_sympos as disambiguator field to klp_func
GCC 6 will include changes to generated code with -mcmodel=large,
which is used to build kernel modules on powerpc64le. This was
necessary because the large model is supposed to allow arbitrary
sizes and locations of the code and data sections, but the ELFv2
global entry point prolog still made the unconditional assumption
that the TOC associated with any particular function can be found
within 2 GB of the function entry point:
func:
addis r2,r12,(.TOC.-func)@ha
addi r2,r2,(.TOC.-func)@l
.localentry func, .-func
To remove this assumption, GCC will now generate instead this global
entry point prolog sequence when using -mcmodel=large:
.quad .TOC.-func
func:
.reloc ., R_PPC64_ENTRY
ld r2, -8(r12)
add r2, r2, r12
.localentry func, .-func
The new .reloc triggers an optimization in the linker that will
replace this new prolog with the original code (see above) if the
linker determines that the distance between .TOC. and func is in
range after all.
Since this new relocation is now present in module object files,
the kernel module loader is required to handle them too. This
patch adds support for the new relocation and implements the
same optimization done by the GNU linker.
Cc: stable@vger.kernel.org
Signed-off-by: Ulrich Weigand <ulrich.weigand@de.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It has come to my attention that kprobe event stack tracing does not
work on powerpc. You can see with the following:
# cd /sys/kernel/debug/tracing
# echo stacktrace > trace_options
# echo 'p kfree' > kprobe_events
# echo 1 > events/kprobes/enable
Will print the following warning:
save_stack_trace_regs() not implemented yet.
Although save_stack_trace() (which normal event stack traces use) is
implemented, save_stack_trace_regs() which kprobe events use is not.
This is a cheap attempt to implement that function.
Note, This may have issues if a task tries to get a stack trace from
another task with its regs, because it just passes in "current" to
save_context_stack(). But this does solve the issue with stack tracing
kprobe events.
Reported-by: Chunyu Hu <chuhu@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently we copy the whole mm_context_t to the paca but only access a
few bits of it. This is wasteful of space paca and also takes quite
some time in the hot path of context switching.
This patch pulls in only the required bits from the mm_context_t to
the paca and on context switch, copies only those.
Benchmarking this (On top of Anton's recent MSR context switching
changes [1]) using processes and yield shows an improvement of almost
3% on POWER8:
http://ozlabs.org/~anton/junkcode/context_switch2.c
./context_switch2 --test=yield --process 0 0
1. https://lists.ozlabs.org/pipermail/linuxppc-dev/2015-October/135700.html
Signed-off-by: Michael Neuling <mikey@neuling.org>
[mpe: Rename paca fields to be mm_ctx_foo rather than context_foo]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds a function to copy the mm->context to the paca. This is
only a basic conversion for now but will be used more extensively in
the next patch.
This also adds #ifdef CONFIG_PPC_BOOK3S around this code since it's
not used elsewhere.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
cppcheck picked up that there were a couple of missing va_end()
calls in functions using va_start().
Signed-off-by: Daniel Axtens <dja@axtens.net>
Reviewed-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PPC476FPE has a different PVR from previous PPC476 processors. The
kexec code checks the PVR in order to correctly setup the MMU. When
the initial support for 476FPE processors was added the corresponding
change in the kexec code was missed. This patch simply adds the check
and solves the following bug on kexec:
kexec: Starting new kernel
Bye!
Unable to handle kernel paging request for instruction fetch
Faulting instruction address: 0xee9a50f8
cpu 0x0: Vector: 400 (Instruction Access) at [ee9d7d20]
pc: ee9a50f8
lr: ee9a50e4
sp: ee9d7dd0
msr: 21020
current = 0xee40f000
pid = 960, comm = kexec
enter ? for help
[link register ] ee9a50e4
[ee9d7dd0] c0013748 default_machine_kexec+0x58/0x70 (unreliable)
[ee9d7df0] c0012f04 machine_kexec+0x34/0x40
[ee9d7e00] c00aa1ec kernel_kexec+0x9c/0xb0
[ee9d7e20] c005d704 SyS_reboot+0x1f4/0x220
[ee9d7f40] c000db68 ret_from_syscall+0x0/0x3c
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The STD_EXCEPTION_PSERIES macro takes both a vector number, and a
location (memory address). However both are always identical, so combine
them to save repeating ourselves.
This does mean an exception handler must always exist at the location in
memory that matches its vector number. But that's OK because this is the
"STD" macro (standard), which does exactly that. We have other macros
for the other cases, eg. STD_EXCEPTION_PSERIES_OOL (out of line).
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
HMT_MEDIUM_PPR_DISCARD is a macro which is present at the start of most
of our first level exception handlers. It conditionally executes a
HMT_MEDIUM instruction, which sets the processor priority to medium.
On on modern systems, ie. Power7 and later, it is nop'ed out at boot.
All it does is make the exception vectors more cramped, and consume 4
bytes of icache.
On old systems it has the effect of boosting the processor priority at
the start of exception processing. If we were previously in the idle
loop for example, we may be at low or very low priority. This is
desirable as we want to process the exception as fast as possible.
However looking closely at the generated code, we see that in all cases
we execute another HMT_MEDIUM just four instructions later. With code
patching applied, the final code on an old (Power6) system will look
like, eg:
c000000000000300 <data_access_pSeries>:
c000000000000300: 7c 42 13 78 mr r2,r2 <-
c000000000000304: 7d b2 43 a6 mtsprg 2,r13
c000000000000308: 7d b1 42 a6 mfsprg r13,1
c00000000000030c: f9 2d 00 80 std r9,128(r13)
c000000000000310: 60 00 00 00 nop
c000000000000314: 7c 42 13 78 mr r2,r2 <-
So I suggest that the added code complexity of HMT_MEDIUM_PPR_DISCARD is
not justified by the benefit of boosting the processor priority for the
duration of four instructions, and therefore we drop it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There are no longer any users of enter_rtas() outside of rtas.c, so make
it "private", by moving the declaration inside rtas.c. Hopefully this
will encourage people to use one of the wrappers which takes the sharp
edges off the RTAS calling sequence.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Although call_rtas_display_status() does actually want to use the
regular RTAS locking, it doesn't want the extra logic that is in
rtas_call(), so currently it open codes the logic.
Instead we can use rtas_call_unlocked(), after taking the RTAS lock.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Most users of RTAS (Run-Time Abstraction Services) use rtas_call(),
which deals with locking as well as endian handling.
However we have two users outside of rtas.c that can't use rtas_call()
because they have different locking requirements.
The hotplug CPU code can't take the RTAS lock because the CPU would go
offline with the lock held and no other CPUs would be able to call RTAS
until the CPU came back online.
The xmon code doesn't want to take the lock because it would risk dead
locking when we are trying to recover from a crash.
Both sites required multiple patches when we added little endian
support, proving that programmers can't do endian right.
Although that ship has sailed, we can still clean the code up by
providing an unlocked version of rtas_call() which avoids the need to
open code the logic elsewhere.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
GregorianDay() is supposed to calculate the day of the week
(tm->tm_wday) for a given day/month/year. In that calcuation it
indexed into an array called MonthOffset using tm->tm_mon-1. However
tm_mon is zero-based, not one-based, so this is off-by-one. It also
means that every January, GregoiranDay() will access element -1 of
the MonthOffset array.
It also doesn't appear to be a correct algorithm either: see in
contrast kernel/time/timeconv.c's time_to_tm function.
It's been broken forever, which suggests no-one in userland uses
this. It looks like no-one in the kernel uses tm->tm_wday either
(see e.g. drivers/rtc/rtc-ds1305.c:319).
tm->tm_wday is conventionally set to -1 when not available in
hardware so we can simply set it to -1 and drop the function.
(There are over a dozen other drivers in drivers/rtc that do
this.)
Found using UBSAN.
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Andrew Morton <akpm@linux-foundation.org> # as an example of what UBSan finds.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: rtc-linux@googlegroups.com
Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- tm: Block signal return from setting invalid MSR state from Michael Neuling
- tm: Check for already reclaimed tasks from Michael Neuling
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=IL8A
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.4-3' into next
Merge the two TM fixes we merged in 4.4. We are about to merge selftests
for these, and without the fixes the selftests will oops.
powerpc fixes for 4.4 #2
- tm: Block signal return from setting invalid MSR state from Michael Neuling
- tm: Check for already reclaimed tasks from Michael Neuling
Print MSR TM bits in oops messages. This appends them to the end
like this:
MSR: 8000000502823031 <SF,VEC,VSX,FP,ME,IR,DR,LE,TM[TE]>
You get the TM[] only if at least one TM MSR bit is set. Inside the
TM[], E means Enabled (bit 32), S means Suspended (bit 33), and T
means Transactional (bit 34)
If no bits are set, you get no TM[] output.
Include rework of printbits() to handle this case.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We should not expect pte bit position in asm code. Simply
by moving part of that to C
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
* pci/aspm:
PCI/ASPM: Make sysfs link_state_store() consistent with link_state_show()
* pci/hotplug:
PCI: pciehp: Always protect pciehp_disable_slot() with hotplug mutex
* pci/misc:
x86/PCI: Simplify pci_bios_{read,write}
PCI: Simplify config space size computation
PCI: Limit config space size for Netronome NFP6000 family
PCI: Add Netronome vendor and device IDs
PCI: Support PCIe devices with short cfg_size
x86/PCI: Clarify AMD Fam10h config access restrictions comment
PCI: Print warnings for all invalid expansion ROM headers
PCI: Check for PCI_HEADER_TYPE_BRIDGE equality, not bitmask
* pci/msi:
PCI/MSI: Remove empty pci_msi_init_pci_dev()
PCI/MSI: Initialize MSI capability for all architectures
Bit 7 of the "Header Type" register indicates a multi-function device when
set. Bits 0-6 contain encoded values, where 0x1 indicates a PCI-PCI
bridge. It is incorrect to test this as though it were a mask.
For example, while the PCI 3.0 spec only defines values 0x0, 0x1, and 0x2,
it's conceivable that a future spec could define 0x3 to mean something
else; then tests for "(hdr_type & 0x7f) & PCI_HEADER_TYPE_BRIDGE" would
incorrectly succeed for this new 0x3 header type.
Test bits 0-6 of the Header Type for equality with PCI_HEADER_TYPE_BRIDGE.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Two DSCR tests have a hack in them:
/*
* XXX: Force a context switch out so that DSCR
* current value is copied into the thread struct
* which is required for the child to inherit the
* changed value.
*/
sleep(1);
We should not be working around this in the testcase, it is a kernel bug.
Fix it by copying the current DSCR to the child, instead of what we
had in the thread struct at last context switch.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
commit 152d523e63 ("powerpc: Create context switch helpers save_sprs()
and restore_sprs()") moved the restore of SPRs after the call to _switch().
There is an issue with this approach - new tasks do not return through
_switch(), they are set up by copy_thread() to directly return through
ret_from_fork() or ret_from_kernel_thread(). This means restore_sprs() is
not getting called for new tasks.
Fix this by moving restore_sprs() before _switch().
Fixes: 152d523e63 ("powerpc: Create context switch helpers save_sprs() and restore_sprs()")
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit a0e72cf12b ("powerpc: Create msr_check_and_{set,clear}()")
removed a call to check_if_tm_restore_required() in the
enable_kernel_*() functions. Add them back in.
Fixes: a0e72cf12b ("powerpc: Create msr_check_and_{set,clear}()")
Reported-by: Rashmica Gupta <rashmicy@gmail.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This reverts commit 527d10ef3a.
The reverted commit breaks cxlflash devices following an EEH reset (and
possibly other cxl devices, however this has not been tested).
The reverted commit changed the behaviour of eeh_reset_device() so that PHB
PEs are not unfrozen following the completion of the reset. This should not
be problematic, as no device resources should have been associated with the
PHB PE.
However, when attempting to load the cxlflash driver after a reset, the
driver attempts to read Vital Product Data through a call to
pci_read_vpd() (which is called on the physical cxl device, not on the
virtual AFU device). pci_read_vpd() in turn attempts to read from the cxl
device's config space. This fails, as the PE it's trying to read from is
still frozen. In turn, the driver gets an -ENODEV and fails to initialise.
It appears this issue only affects some parts of the VPD area, as "lspci
-vvv", which only reads a subset of the VPD bytes, is not broken by the
original patch.
At this stage, we don't fully understand why we're trying to read a frozen
PE, and we don't know how this affects other cxl devices. It is possible
that there is an underlying bug in the cxl driver or the powerpc CAPI
support code, or alternatively a bug in the PCI resource allocation/mapping
code that is incorrectly mapping resources to PE#0.
As such, this fix is incomplete, however it is necessary to prevent a
serious regression in CAPI support.
In the meantime, revert the commit, especially as it was intended to be a
non-functional change.
Cc: Gavin Shan <gwshan@linux.vnet.ibm.com>
Cc: Ian Munsie <imunsie@au1.ibm.com>
Cc: Daniel Axtens <dja@axtens.net>
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Makes it easier to handle init vs core cleanly, though the change is
fairly invasive across random architectures.
It simplifies the rbtree code immediately, however, while keeping the
core data together in the same cachline (now iff the rbtree code is
enabled).
Acked-by: Peter Zijlstra <peterz@infradead.org>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Remove a bunch of unnecessary fallback functions and group
things in a more logical way.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Most of __switch_to() is housekeeping, TLB batching, timekeeping etc.
Move these away from the more complex and critical context switching
code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Create a single function that flushes everything (FP, VMX, VSX, SPE).
Doing this all at once means we only do one MSR write.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Create a single function that gives everything up (FP, VMX, VSX, SPE).
Doing this all at once means we only do one MSR write.
A context switch microbenchmark using yield():
http://ozlabs.org/~anton/junkcode/context_switch2.c
./context_switch2 --test=yield --fp --altivec --vector 0 0
shows an improvement of 3% on POWER8.
Signed-off-by: Anton Blanchard <anton@samba.org>
[mpe: giveup_all() needs to be EXPORT_SYMBOL'ed]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
More consolidation of our MSR available bit handling.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a boot option that strictly manages the MSR unavailable bits.
This catches kernel uses of FP/Altivec/SPE that would otherwise
corrupt user state.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The enable_kernel_*() functions leave the relevant MSR bits enabled
until we exit the kernel sometime later. Create disable versions
that wrap the kernel use of FP, Altivec VSX or SPE.
While we don't want to disable it normally for performance reasons
(MSR writes are slow), it will be used for a debug boot option that
does this and catches bad uses in other areas of the kernel.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Create helper functions to set and clear MSR bits after first
checking if they are already set. Grouping them will make it
easy to avoid the MSR writes in a subsequent optimisation.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move the MSR modification into c. Removing it from the assembly
function will allow us to avoid costly MSR writes by batching them
up.
Check the FP and VMX bits before calling the relevant giveup_*()
function. This makes giveup_vsx() and flush_vsx_to_thread() perform
more like their sister functions, and allows us to use
flush_vsx_to_thread() in the signal code.
Move the check_if_tm_restore_required() check in.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move the MSR modification into new c functions. Removing it from
the low level functions will allow us to avoid costly MSR writes
by batching them up.
Move the check_if_tm_restore_required() check into these new functions.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We used to allow giveup_*() to be called with a NULL task struct
pointer. Now those cases are handled in the caller we can remove
the checks. We can also remove giveup_altivec_notask() which is also
unused.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
mtmsrd_isync() will do an mtmsrd followed by an isync on older
processors. On newer processors we avoid the isync via a feature fixup.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Instead of having multiple giveup_*_maybe_transactional() functions,
separate out the TM check into a new function called
check_if_tm_restore_required().
This will make it easier to optimise the giveup_*() functions in a
subsequent patch.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The UP only lazy floating point and vector optimisations were written
back when SMP was not common, and neither glibc nor gcc used vector
instructions. Now SMP is very common, glibc aggressively uses vector
instructions and gcc autovectorises.
We want to add new optimisations that apply to both UP and SMP, but
in preparation for that remove these UP only optimisations.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move all our context switch SPR save and restore code into two
helpers. We do a few optimisations:
- Group all mfsprs and all mtsprs. In many cases an mtspr sets a
scoreboarding bit that an mfspr waits on, so the current practise of
mfspr A; mtspr A; mfpsr B; mtspr B is the worst scheduling we can
do.
- SPR writes are slow, so check that the value is changing before
writing it.
A context switch microbenchmark using yield():
http://ozlabs.org/~anton/junkcode/context_switch2.c
./context_switch2 --test=yield 0 0
shows an improvement of almost 10% on POWER8.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Similar to the non TM load_up_*() functions, don't disable the MSR
bits on the way out.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Writing the MSR is slow, so we want to avoid it whenever possible.
A subsequent patch will add a debug option that strictly manages the
FP/VMX/VSX unavailable bits. For now just remove it, matching what
we do in other areas of the kernel (eg enable_kernel_altivec()).
A context switch microbenchmark using yield():
http://ozlabs.org/~anton/junkcode/context_switch2.c
./context_switch2 --test=yield --fp 0 0
shows an improvement of almost 3% on POWER8.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently, if HV KVM is configured but PR KVM isn't, we don't include
a test to see whether we were interrupted in KVM guest context for the
set of interrupts which get delivered directly to the guest by hardware
if they occur in the guest. This includes things like program
interrupts.
However, the recent bug where userspace could set the MSR for a VCPU
to have an illegal value in the TS field, and thus cause a TM Bad Thing
type of program interrupt on the hrfid that enters the guest, showed that
we can never be completely sure that these interrupts can never occur
in the guest entry/exit code. If one of these interrupts does happen
and we have HV KVM configured but not PR KVM, then we end up trying to
run the handler in the host with the MMU set to the guest MMU context,
which generally ends badly.
Thus, for robustness it is better to have the test in every interrupt
vector, so that if some way is found to trigger some interrupt in the
guest entry/exit path, we can handle it without immediately crashing
the host.
This means that the distinction between KVMTEST and KVMTEST_PR goes
away. Thus we delete KVMTEST_PR and associated macros and use KVMTEST
everywhere that we previously used either KVMTEST_PR or KVMTEST. It
also means that SOFTEN_TEST_HV_201 becomes the same as SOFTEN_TEST_PR,
so we deleted SOFTEN_TEST_HV_201 and use SOFTEN_TEST_PR instead.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It is common practice with powerpc to use 'rN' to refer to register 'N'. However
when using the pt_regs_offset table we have to use 'gprN'.
So add aliases such that both 'rN' and 'gprN' can be used.
For example, we can currently do:
$ su -
$ cd /sys/kernel/debug/tracing
$ echo "p:probe/sys_fchownat sys_fchownat %gpr3:s32 +0(%gpr4):string %gpr5:s32 %gpr6:s32 %gpr7:s32" > kprobe_events
$ echo 1 > events/probe/sys_fchownat/enable
$ touch /tmp/foo
$ chown root /tmp/foo
$ echo 0 > events/enable
$ cat trace
chown-2925 [014] d... 76.160657: sys_fchownat: (SyS_fchownat+0x8/0x1a0) arg1=-100 arg2="/tmp/foo" arg3=0 arg4=-1 arg5=0
Instead we'd like to be able to use:
$ echo "p:probe/sys_fchownat sys_fchownat %r3:s32 +0(%r4):string %r5:s32 %r6:s32 %r7:s32" > kprobe_events
Signed-off-by: Rashmica Gupta <rashmicy@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Most architectures use NR_syscalls as the #define for the number of syscalls.
We use __NR_syscalls, and then define NR_syscalls as __NR_syscalls.
__NR_syscalls is not used outside arch code, whereas NR_syscalls is. So as
NR_syscalls must be defined and __NR_syscalls does not, replace __NR_syscalls
with NR_syscalls.
Signed-off-by: Rashmica Gupta <rashmicy@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This function has been unused since commit 14cf11af6c ("powerpc: Merge enough
to start building in arch/powerpc."), so remove it.
Signed-off-by: Rashmica Gupta <rashmicy@gmail.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
1851617cd2 ("PCI/MSI: Disable MSI at enumeration even if kernel doesn't
support MSI") moved dev->msi_cap and dev->msix_cap initialization from the
pci_init_capabilities() path (used on all architectures) to the
pci_setup_device() path (not used on Open Firmware architectures).
This broke MSI or MSI-X on Open Firmware machines. 4d9aac397a
("powerpc/PCI: Disable MSI/MSI-X interrupts at PCI probe time in OF case")
fixed it for PowerPC but not for SPARC.
Set up MSI and MSI-X (initialize msi_cap and msix_cap and disable MSI and
MSI-X) in pci_init_capabilities() so all architectures do it the same way.
This reverts 4d9aac397a since this patch fixes the problem generically
for both PowerPC and SPARC.
[bhelgaas: changelog, make pci_msi_setup_pci_dev() static]
Fixes: 1851617cd2 ("PCI/MSI: Disable MSI at enumeration even if kernel doesn't support MSI")
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Currently we can hit a scenario where we'll tm_reclaim() twice. This
results in a TM bad thing exception because the second reclaim occurs
when not in suspend mode.
The scenario in which this can happen is the following. We attempt to
deliver a signal to userspace. To do this we need obtain the stack
pointer to write the signal context. To get this stack pointer we
must tm_reclaim() in case we need to use the checkpointed stack
pointer (see get_tm_stackpointer()). Normally we'd then return
directly to userspace to deliver the signal without going through
__switch_to().
Unfortunatley, if at this point we get an error (such as a bad
userspace stack pointer), we need to exit the process. The exit will
result in a __switch_to(). __switch_to() will attempt to save the
process state which results in another tm_reclaim(). This
tm_reclaim() now causes a TM Bad Thing exception as this state has
already been saved and the processor is no longer in TM suspend mode.
Whee!
This patch checks the state of the MSR to ensure we are TM suspended
before we attempt the tm_reclaim(). If we've already saved the state
away, we should no longer be in TM suspend mode. This has the
additional advantage of checking for a potential TM Bad Thing
exception.
Found using syscall fuzzer.
Fixes: fb09692e71 ("powerpc: Add reclaim and recheckpoint functions for context switching transactional memory processes")
Cc: stable@vger.kernel.org # v3.9+
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently we allow both the MSR T and S bits to be set by userspace on
a signal return. Unfortunately this is a reserved configuration and
will cause a TM Bad Thing exception if attempted (via rfid).
This patch checks for this case in both the 32 and 64 bit signals
code. If both T and S are set, we mark the context as invalid.
Found using a syscall fuzzer.
Fixes: 2b0a576d15 ("powerpc: Add new transactional memory state to the signal context")
Cc: stable@vger.kernel.org # v3.9+
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- Kconfig: remove BE-only platforms from LE kernel build from Boqun Feng
- Refresh ps3_defconfig from Geoff Levand
- Emit GNU & SysV hashes for the vdso from Michael Ellerman
- Define an enum for the bolted SLB indexes from Anshuman Khandual
- Use a local to avoid multiple calls to get_slb_shadow() from Michael Ellerman
- Add gettimeofday() benchmark from Michael Neuling
- Avoid link stack corruption in __get_datapage() from Michael Neuling
- Add virt_to_pfn and use this instead of opencoding from Aneesh Kumar K.V
- Add ppc64le_defconfig from Michael Ellerman
- pseries: extract of_helpers module from Andy Shevchenko
- Correct string length in pseries_of_derive_parent() from Nathan Fontenot
- Free the MSI bitmap if it was slab allocated from Denis Kirjanov
- Shorten irq_chip name for the SIU from Christophe Leroy
- Wait 1s for secondaries to enter OPAL during kexec from Samuel Mendoza-Jonas
- Fix _ALIGN_* errors due to type difference. from Aneesh Kumar K.V
- powerpc/pseries/hvcserver: don't memset pi_buff if it is null from Colin Ian King
- Disable hugepd for 64K page size. from Aneesh Kumar K.V
- Differentiate between hugetlb and THP during page walk from Aneesh Kumar K.V
- Make PCI non-optional for pseries from Michael Ellerman
- Individual System V IPC system calls from Sam bobroff
- Add selftest of unmuxed IPC calls from Michael Ellerman
- discard .exit.data at runtime from Stephen Rothwell
- Delete old orphaned PrPMC 280/2800 DTS and boot file. from Paul Gortmaker
- Use of_get_next_parent to simplify code from Christophe Jaillet
- Paginate some xmon output from Sam bobroff
- Add some more elements to the xmon PACA dump from Michael Ellerman
- Allow the tm-syscall selftest to build with old headers from Michael Ellerman
- Run EBB selftests only on POWER8 from Denis Kirjanov
- Drop CONFIG_TUNE_CELL in favour of CONFIG_CELL_CPU from Michael Ellerman
- Avoid reference to potentially freed memory in prom.c from Christophe Jaillet
- Quieten boot wrapper output with run_cmd from Geoff Levand
- EEH fixes and cleanups from Gavin Shan
- Fix recursive fenced PHB on Broadcom shiner adapter from Gavin Shan
- Use of_get_next_parent() in of_get_ibm_chip_id() from Michael Ellerman
- Fix section mismatch warning in msi_bitmap_alloc() from Denis Kirjanov
- Fix ps3-lpm white space from Rudhresh Kumar J
- Fix ps3-vuart null dereference from Colin King
- nvram: Add missing kfree in error path from Christophe Jaillet
- nvram: Fix function name in some errors messages. from Christophe Jaillet
- drivers/macintosh: adb: fix misleading Kconfig help text from Aaro Koskinen
- agp/uninorth: fix a memleak in create_gatt_table from Denis Kirjanov
- cxl: Free virtual PHB when removing from Andrew Donnellan
- scripts/kconfig/Makefile: Allow KBUILD_DEFCONFIG to be a target from Michael Ellerman
- scripts/kconfig/Makefile: Fix KBUILD_DEFCONFIG check when building with O= from Michael Ellerman
- Freescale updates from Scott: Highlights include 64-bit book3e kexec/kdump
support, a rework of the qoriq clock driver, device tree changes including
qoriq fman nodes, support for a new 85xx board, and some fixes.
- MPC5xxx updates from Anatolij: Highlights include a driver for MPC512x
LocalPlus Bus FIFO with its device tree binding documentation, mpc512x
device tree updates and some minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YwcM
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Kconfig: remove BE-only platforms from LE kernel build from Boqun
Feng
- Refresh ps3_defconfig from Geoff Levand
- Emit GNU & SysV hashes for the vdso from Michael Ellerman
- Define an enum for the bolted SLB indexes from Anshuman Khandual
- Use a local to avoid multiple calls to get_slb_shadow() from Michael
Ellerman
- Add gettimeofday() benchmark from Michael Neuling
- Avoid link stack corruption in __get_datapage() from Michael Neuling
- Add virt_to_pfn and use this instead of opencoding from Aneesh Kumar
K.V
- Add ppc64le_defconfig from Michael Ellerman
- pseries: extract of_helpers module from Andy Shevchenko
- Correct string length in pseries_of_derive_parent() from Nathan
Fontenot
- Free the MSI bitmap if it was slab allocated from Denis Kirjanov
- Shorten irq_chip name for the SIU from Christophe Leroy
- Wait 1s for secondaries to enter OPAL during kexec from Samuel
Mendoza-Jonas
- Fix _ALIGN_* errors due to type difference, from Aneesh Kumar K.V
- powerpc/pseries/hvcserver: don't memset pi_buff if it is null from
Colin Ian King
- Disable hugepd for 64K page size, from Aneesh Kumar K.V
- Differentiate between hugetlb and THP during page walk from Aneesh
Kumar K.V
- Make PCI non-optional for pseries from Michael Ellerman
- Individual System V IPC system calls from Sam bobroff
- Add selftest of unmuxed IPC calls from Michael Ellerman
- discard .exit.data at runtime from Stephen Rothwell
- Delete old orphaned PrPMC 280/2800 DTS and boot file, from Paul
Gortmaker
- Use of_get_next_parent to simplify code from Christophe Jaillet
- Paginate some xmon output from Sam bobroff
- Add some more elements to the xmon PACA dump from Michael Ellerman
- Allow the tm-syscall selftest to build with old headers from Michael
Ellerman
- Run EBB selftests only on POWER8 from Denis Kirjanov
- Drop CONFIG_TUNE_CELL in favour of CONFIG_CELL_CPU from Michael
Ellerman
- Avoid reference to potentially freed memory in prom.c from Christophe
Jaillet
- Quieten boot wrapper output with run_cmd from Geoff Levand
- EEH fixes and cleanups from Gavin Shan
- Fix recursive fenced PHB on Broadcom shiner adapter from Gavin Shan
- Use of_get_next_parent() in of_get_ibm_chip_id() from Michael
Ellerman
- Fix section mismatch warning in msi_bitmap_alloc() from Denis
Kirjanov
- Fix ps3-lpm white space from Rudhresh Kumar J
- Fix ps3-vuart null dereference from Colin King
- nvram: Add missing kfree in error path from Christophe Jaillet
- nvram: Fix function name in some errors messages, from Christophe
Jaillet
- drivers/macintosh: adb: fix misleading Kconfig help text from Aaro
Koskinen
- agp/uninorth: fix a memleak in create_gatt_table from Denis Kirjanov
- cxl: Free virtual PHB when removing from Andrew Donnellan
- scripts/kconfig/Makefile: Allow KBUILD_DEFCONFIG to be a target from
Michael Ellerman
- scripts/kconfig/Makefile: Fix KBUILD_DEFCONFIG check when building
with O= from Michael Ellerman
- Freescale updates from Scott: Highlights include 64-bit book3e
kexec/kdump support, a rework of the qoriq clock driver, device tree
changes including qoriq fman nodes, support for a new 85xx board, and
some fixes.
- MPC5xxx updates from Anatolij: Highlights include a driver for
MPC512x LocalPlus Bus FIFO with its device tree binding
documentation, mpc512x device tree updates and some minor fixes.
* tag 'powerpc-4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (106 commits)
powerpc/msi: Fix section mismatch warning in msi_bitmap_alloc()
powerpc/prom: Use of_get_next_parent() in of_get_ibm_chip_id()
powerpc/pseries: Correct string length in pseries_of_derive_parent()
powerpc/e6500: hw tablewalk: make sure we invalidate and write to the same tlb entry
powerpc/mpc85xx: Add FSL QorIQ DPAA FMan support to the SoC device tree(s)
powerpc/mpc85xx: Create dts components for the FSL QorIQ DPAA FMan
powerpc/fsl: Add #clock-cells and clockgen label to clockgen nodes
powerpc: handle error case in cpm_muram_alloc()
powerpc: mpic: use IRQCHIP_SKIP_SET_WAKE instead of redundant mpic_irq_set_wake
powerpc/book3e-64: Enable kexec
powerpc/book3e-64/kexec: Set "r4 = 0" when entering spinloop
powerpc/booke: Only use VIRT_PHYS_OFFSET on booke32
powerpc/book3e-64/kexec: Enable SMP release
powerpc/book3e-64/kexec: create an identity TLB mapping
powerpc/book3e-64: Don't limit paca to 256 MiB
powerpc/book3e/kdump: Enable crash_kexec_wait_realmode
powerpc/book3e: support CONFIG_RELOCATABLE
powerpc/booke64: Fix args to copy_and_flush
powerpc/book3e-64: rename interrupt_end_book3e with __end_interrupts
powerpc/e6500: kexec: Handle hardware threads
...
Pull security subsystem update from James Morris:
"This is mostly maintenance updates across the subsystem, with a
notable update for TPM 2.0, and addition of Jarkko Sakkinen as a
maintainer of that"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (40 commits)
apparmor: clarify CRYPTO dependency
selinux: Use a kmem_cache for allocation struct file_security_struct
selinux: ioctl_has_perm should be static
selinux: use sprintf return value
selinux: use kstrdup() in security_get_bools()
selinux: use kmemdup in security_sid_to_context_core()
selinux: remove pointless cast in selinux_inode_setsecurity()
selinux: introduce security_context_str_to_sid
selinux: do not check open perm on ftruncate call
selinux: change CONFIG_SECURITY_SELINUX_CHECKREQPROT_VALUE default
KEYS: Merge the type-specific data with the payload data
KEYS: Provide a script to extract a module signature
KEYS: Provide a script to extract the sys cert list from a vmlinux file
keys: Be more consistent in selection of union members used
certs: add .gitignore to stop git nagging about x509_certificate_list
KEYS: use kvfree() in add_key
Smack: limited capability for changing process label
TPM: remove unnecessary little endian conversion
vTPM: support little endian guests
char: Drop owner assignment from i2c_driver
...
Freescale updates from Scott:
"Highlights include 64-bit book3e kexec/kdump support, a rework of the
qoriq clock driver, device tree changes including qoriq fman nodes,
support for a new 85xx board, and some fixes.
Note that there is a trivial merge conflict with the clock tree's next
branch, in the clock Makefile."
When turning this from inline to an exported function I was a bit
over-eager and made it GPL only. This prevents the use of pretty much
all non-GPL PCI driver which is a bit over the top. Let's bring it
back in line with other architecture.
Fixes: 817820b022 ("powerpc/iommu: Support "hybrid" iommu/direct DMA ops for coherent_mask < dma_mask")
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use of_get_next_parent() to simplifiy the logic in of_get_ibm_chip_id().
Original-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Allow KEXEC for book3e, and bypass or convert non-book3e stuff
in kexec code.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
[scottwood@freescale.com: move code to minimize diff, and cleanup]
Signed-off-by: Scott Wood <scottwood@freescale.com>
The SMP release mechanism for FSL book3e is different from when booting
with normal hardware. In theory we could simulate the normal spin
table mechanism, but not at the addresses U-Boot put in the device tree
-- so there'd need to be even more communication between the kernel and
kexec to set that up. Instead, kexec-tools will set a boolean property
linux,booted-from-kexec in the /chosen node.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: devicetree@vger.kernel.org
book3e has no real MMU mode so we have to create an identity TLB
mapping to make sure we can access the real physical address.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
[scottwood: cleanup, and split off some changes]
Signed-off-by: Scott Wood <scottwood@freescale.com>
This limit only makes sense on book3s, and on book3e it can cause
problems with kdump if we don't have any memory under 256 MiB.
Signed-off-by: Scott Wood <scottwood@freescale.com>
While book3e doesn't have "real mode", we still want to wait for
all the non-crash cpus to complete their shutdown.
Signed-off-by: Scott Wood <scottwood@freescale.com>
book3e is different with book3s since 3s includes the exception
vectors code in head_64.S as it relies on absolute addressing
which is only possible within this compilation unit. So we have
to get that label address with got.
And when boot a relocated kernel, we should reset ipvr properly again
after .relocate.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
[scottwood: cleanup and ifdef removal]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Convert r4/r5, not r6, to a virtual address when calling
copy_and_flush. Otherwise, r3 is already virtual, and copy_to_flush
tries to access r3+r6, PAGE_OFFSET gets added twice.
This isn't normally seen because on book3e we normally enter with
the kernel at zero and thus skip copy_to_flush -- but it will be
needed for kexec support.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
[scottwood: split patch and rewrote changelog]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Rename 'interrupt_end_book3e' to '__end_interrupts' so that the symbol
can be used by both book3s and book3e.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
[scottwood: edit changelog]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Use an AS=1 trampoline TLB entry to allow all normal TLB1 entries to
be loaded at once. This avoids the need to keep the translation that
code is executing from in the same TLB entry in the final TLB
configuration as during early boot, which in turn is helpful for
relocatable kernels (e.g. kdump) where the kernel is not running from
what would be the first TLB entry.
On e6500, we limit map_mem_in_cams() to the primary hwthread of a
core (the boot cpu is always considered primary, as a kdump kernel
can be entered on any cpu). Each TLB only needs to be set up once,
and when we do, we don't want another thread to be running when we
create a temporary trampoline TLB1 entry.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Currently we do not validate rtas.entry before calling enter_rtas(). This
leads to a kernel oops when user space calls rtas system call on a powernv
platform (see below). This patch adds code to validate rtas.entry before
making enter_rtas() call.
Oops: Exception in kernel mode, sig: 4 [#1]
SMP NR_CPUS=1024 NUMA PowerNV
task: c000000004294b80 ti: c0000007e1a78000 task.ti: c0000007e1a78000
NIP: 0000000000000000 LR: 0000000000009c14 CTR: c000000000423140
REGS: c0000007e1a7b920 TRAP: 0e40 Not tainted (3.18.17-340.el7_1.pkvm3_1_0.2400.1.ppc64le)
MSR: 1000000000081000 <HV,ME> CR: 00000000 XER: 00000000
CFAR: c000000000009c0c SOFTE: 0
NIP [0000000000000000] (null)
LR [0000000000009c14] 0x9c14
Call Trace:
[c0000007e1a7bba0] [c00000000041a7f4] avc_has_perm_noaudit+0x54/0x110 (unreliable)
[c0000007e1a7bd80] [c00000000002ddc0] ppc_rtas+0x150/0x2d0
[c0000007e1a7be30] [c000000000009358] syscall_exit+0x0/0x98
Cc: stable@vger.kernel.org # v3.2+
Fixes: 55190f8878 ("powerpc: Add skeleton PowerNV platform")
Reported-by: NAGESWARA R. SASTRY <nasastry@in.ibm.com>
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
[mpe: Reword change log, trim oops, and add stable + fixes]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When one or both of the below two flags are marked in the PE state, the
PE's IO path is regarded as enabled: EEH_STATE_MMIO_ACTIVE or
EEH_STATE_MMIO_ENABLED.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On fenced PHB, the error handlers in the drivers of its subordinate
devices could return PCI_ERS_RESULT_CAN_RECOVER, indicating no reset
will be issued during the recovery. It's conflicting with the fact
that fenced PHB won't be recovered without reset.
This limits the return value from the error handlers in the drivers
of the fenced PHB's subordinate devices to PCI_ERS_RESULT_NEED_NONE
or PCI_ERS_RESULT_NEED_RESET, to ensure reset will be issued during
recovery.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently, we rely on the existence of struct pci_driver::err_handler
to decide if the corresponding PCI device should be unplugged during
EEH recovery (partially hotplug case). However that check is not
sufficient. Some device drivers implement only some of the EEH error
handlers to collect diag-data. That means the driver still expects a
hotplug to recover from the EEH error.
This makes the hotplug criterion more relaxed: if the device driver
doesn't provide all necessary EEH error handlers, it will experience
hotplug during EEH recovery.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
[mpe: Minor change log rewording]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On PowerNV platform, the PE is kept in frozen state until the PE
reset is completed to avoid recursive EEH error caused by MMIO
access during the period of EEH reset. The PE's frozen state is
cleared after BARs of PCI device included in the PE are restored
and enabled. However, we needn't clear the frozen state for PHB PE
explicitly at this point as there is no real PE for PHB PE. As the
PHB PE is always binding with PE#0, we actually clear PE#0, which
is wrong. It doesn't incur any problem though.
This checks if the PE is PHB PE and doesn't clear the frozen state
if it is.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
of_get_property() is used inside the loop, but then the reference to the
node is dropped before dereferencing the prop pointer, which could by then
point to junk if the node has been freed.
Instead use of_property_read_u32() to actually read the property
value before dropping the reference.
of_property_read_u32() requires at least one cell (u32) to be present,
which is stricter than the old logic which would happily dereference a
property of any size. However we believe all device trees in the wild
have at least one cell.
Skiboot may produce memory nodes with more than one cell, but that is
OK, of_property_read_u32() will return the first one.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
[mpe: Expand change log with device tree details]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The OS should ask Power Firmware (PFW) for the size of the buffer
allocated for the event log, instead of the size of the actual
event log. It then passes the buffer adddress and size to PFW in
the handover process, into which PFW copies the log.
Signed-off-by: Hon Ching(Vicky) Lo <honclo@linux.vnet.ibm.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
The event log generated by OpenFirmware in PowerPC is 4-byte aligned.
This patch reformats the log to be byte-aligned for the Linux client.
Signed-off-by: Hon Ching(Vicky) Lo <honclo@linux.vnet.ibm.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Replace all occurrences of '/ibm,vtpm' with '/vdevice/vtpm',
as only the latter is guanranteed to be available for the client OS.
The '/ibm,vtpm' node should only be used by Open Firmware, which
is susceptible to changes.
Signed-off-by: Hon Ching(Vicky) Lo <honclo@linux.vnet.ibm.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
.exit.text is discarded at run time and there are some references from
that to .exit.data, so we need to discard .exit.data at run time as well.
Fixes these errors:
`.exit.data' referenced in section `.exit.text' of drivers/built-in.o: defined in discarded section `.exit.data' of drivers/built-in.o
`.exit.data' referenced in section `.exit.text' of drivers/built-in.o: defined in discarded section `.exit.data' of drivers/built-in.o
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
No need to have two atomic opertions (update and fetch/check) when
decreasing PE's number of passed devices as one atomic operation
is enough.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Export pcibios_free_controller(), so it can be used by the cxl module to
free virtual PHBs.
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We need to properly identify whether a hugepage is an explicit or
a transparent hugepage in follow_huge_addr(). We used to depend
on hugepage shift argument to do that. But in some case that can
result in wrong results. For ex:
On finding a transparent hugepage we set hugepage shift to PMD_SHIFT.
But we can end up clearing the thp pte, via pmdp_huge_get_and_clear.
We do prevent reusing the pfn page via the usage of
kick_all_cpus_sync(). But that happens after we updated the pte to 0.
Hence in follow_huge_addr() we can find hugepage shift set, but transparent
huge page check fail for a thp pte.
NOTE: We fixed a variant of this race against thp split in commit
691e95fd73
("powerpc/mm/thp: Make page table walk safe against thp split/collapse")
Without this patch, we may hit the BUG_ON(flags & FOLL_GET) in
follow_page_mask occasionally.
In the long term, we may want to switch ppc64 64k page size config to
enable CONFIG_ARCH_WANT_GENERAL_HUGETLB
Reported-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
'nvram_create_os_partition' should be 'nvram_create_partition'.
Use __func__ to have it right, as done elsewhere in this file.
Signed-off-by: Christophe Jaillet <christophe.jaillet@wanadoo.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If 'nvram_write_header' fails, then 'new_part' should be freed, otherwise,
there is a memory leak.
Signed-off-by: Christophe Jaillet <christophe.jaillet@wanadoo.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc has a link register (lr) used for calling functions. We "bl
<func>" to call a function, and "blr" to return back to the call site.
The lr is only a single register, so if we call another function from
inside this function (ie. nested calls), software must save away the
lr on the software stack before calling the new function. Before
returning (ie. before the "blr"), the lr is restored by software from
the software stack.
This makes branch prediction quite difficult for the processor as it
will only know the branch target just before the "blr".
To help with this, modern powerpc processors keep a (non-architected)
hardware stack of lr called a "link stack". When a "bl <func>" is
run, the lr is pushed onto this stack. When a "blr" is called, the
branch predictor pops the lr value from the top of the link stack, and
uses it to predict the branch target. Hence the processor pipeline
knows a lot earlier the branch target.
This works great but there are some cases where you call "bl" but
without a matching "blr". Once such case is when trying to determine
the program counter (which can't be read directly). Here you "bl+4;
mflr" to get the program counter. If you do this, the link stack will
get out of sync with reality, causing the branch predictor to
mis-predict subsequent function returns.
To avoid this, modern micro-architectures have a special case of bl.
Using the form "bcl 20,31,+4", ensures the processor doesn't push to
the link stack.
The 32 and 64 bit variants of __get_datapage() use a "bl; mflr" to
determine the loaded address of the VDSO. The current versions of
these attempt to use this special bl variant.
Unfortunately they use +8 rather than the required +4. Hence the
current code results in the link stack getting out of sync with
reality and hence the resulting performance degradation.
This patch moves it to bcl+4 by moving __kernel_datapage_offset out of
__get_datapage().
With this patch, running a gettimeofday() (which uses
__get_datapage()) microbenchmark we get a decent bump in performance
on POWER7/8.
For the benchmark in tools/testing/selftests/powerpc/benchmarks/gettimeofday.c
POWER8:
64bit gets ~4% improvement
32bit gets ~9% improvement
POWER7:
64bit gets ~7% improvement
Signed-off-by: Michael Neuling <mikey@neuling.org>
Reported-by: Aaron Sawdey <sawdey@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Andy Lutomirski says:
Some dynamic loaders may be slightly faster if a GNU hash is
available.
This is unlikely to have any measurable effect on the time it takes
to resolve vdso symbols (since there are so few of them). In some
contexts, it can be a win for a different reason: if every DSO has a
GNU hash section, then libc can avoid calculating SysV hashes at
all. Both musl and glibc appear to have this optimization.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Resource management
- Revert pci_read_bridge_bases() unification (Bjorn Helgaas)
- Clear IORESOURCE_UNSET when clipping a bridge window (Bjorn Helgaas)
MSI
- Fix MSI IRQ domains for VFs on virtual buses (Alex Williamson)
Renesas R-Car host bridge driver
- Add R8A7794 support (Sergei Shtylyov)
Miscellaneous
- Fix devfn for VPD access through function 0 (Alex Williamson)
- Use function 0 VPD only for identical functions (Alex Williamson)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=f4c3
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.3-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"These are fixes for things we merged for v4.3 (VPD, MSI, and bridge
window management), and a new Renesas R8A7794 SoC device ID.
Details:
Resource management:
- Revert pci_read_bridge_bases() unification (Bjorn Helgaas)
- Clear IORESOURCE_UNSET when clipping a bridge window (Bjorn
Helgaas)
MSI:
- Fix MSI IRQ domains for VFs on virtual buses (Alex Williamson)
Renesas R-Car host bridge driver:
- Add R8A7794 support (Sergei Shtylyov)
Miscellaneous:
- Fix devfn for VPD access through function 0 (Alex Williamson)
- Use function 0 VPD only for identical functions (Alex Williamson)"
* tag 'pci-v4.3-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: rcar: Add R8A7794 support
PCI: Use function 0 VPD for identical functions, regular VPD for others
PCI: Fix devfn for VPD access through function 0
PCI/MSI: Fix MSI IRQ domains for VFs on virtual buses
PCI: Clear IORESOURCE_UNSET when clipping a bridge window
PCI: Revert "PCI: Call pci_read_bridge_bases() from core instead of arch code"
Pull irq updates from Thomas Gleixner:
"This is a rather large update post rc1 due to the final steps of
cleanups and API changes which had to wait for the preparatory patches
to hit your tree.
- Regression fixes for ARM GIC irqchips
- Regression fixes and lockdep anotations for renesas irq chips
- The leftovers of the cleanup and preparatory patches which have
been ignored by maintainers
- Final conversions of the newly merged users of obsolete APIs
- Final removal of obsolete APIs
- Final removal of ARM artifacts which had been introduced during the
conversion of ARM to the generic interrupt code.
- Final split of the irq_data into chip specific and common data to
reflect the needs of hierarchical irq domains.
- Treewide removal of the first argument of interrupt flow handlers,
i.e. the irq number, which is not used by the majority of handlers
and simple to retrieve from the other argument the irq descriptor.
- A few comment updates and build warning fixes"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (40 commits)
arm64: Remove ununsed set_irq_flags
ARM: Remove ununsed set_irq_flags
sh: Kill off set_irq_flags usage
irqchip: Kill off set_irq_flags usage
gpu/drm: Kill off set_irq_flags usage
genirq: Remove irq argument from irq flow handlers
genirq: Move field 'msi_desc' from irq_data into irq_common_data
genirq: Move field 'affinity' from irq_data into irq_common_data
genirq: Move field 'handler_data' from irq_data into irq_common_data
genirq: Move field 'node' from irq_data into irq_common_data
irqchip/gic-v3: Use IRQD_FORWARDED_TO_VCPU flag
irqchip/gic: Use IRQD_FORWARDED_TO_VCPU flag
genirq: Provide IRQD_FORWARDED_TO_VCPU status flag
genirq: Simplify irq_data_to_desc()
genirq: Remove __irq_set_handler_locked()
pinctrl/pistachio: Use irq_set_handler_locked
gpio: vf610: Use irq_set_handler_locked
powerpc/mpc8xx: Use irq_set_handler_locked()
powerpc/ipic: Use irq_set_handler_locked()
powerpc/cpm2: Use irq_set_handler_locked()
...
- Fix 32-bit TCE table init in kdump kernel from Nish
- Fix kdump with non-power-of-2 crashkernel= from Nish
- Abort cxl_pci_enable_device_hook() if PCI channel is offline from Andrew
- Fix to release DRC when configure_connector() fails from Bharata
- Wire up sys_userfaultfd()
- Fix race condition in tearing down MSI interrupts from Paul
- Fix unbalanced pci_dev_get() in cxl_probe() from Daniel
- Fix cxl build failure due to -Wunused-variable gcc behaviour change from Ian
- Tell the toolchain to use ABI v2 when building an LE boot wrapper from Benh
- Fix THP to recompute hash value after a failed update from Aneesh
- 32-bit memcpy/memset: only use dcbz once cache is enabled from Christophe
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Dgn5
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix 32-bit TCE table init in kdump kernel from Nish
- Fix kdump with non-power-of-2 crashkernel= from Nish
- Abort cxl_pci_enable_device_hook() if PCI channel is offline from
Andrew
- Fix to release DRC when configure_connector() fails from Bharata
- Wire up sys_userfaultfd()
- Fix race condition in tearing down MSI interrupts from Paul
- Fix unbalanced pci_dev_get() in cxl_probe() from Daniel
- Fix cxl build failure due to -Wunused-variable gcc behaviour change
from Ian
- Tell the toolchain to use ABI v2 when building an LE boot wrapper
from Benh
- Fix THP to recompute hash value after a failed update from Aneesh
- 32-bit memcpy/memset: only use dcbz once cache is enabled from
Christophe
* tag 'powerpc-4.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc32: memset: only use dcbz once cache is enabled
powerpc32: memcpy: only use dcbz once cache is enabled
powerpc/mm: Recompute hash value after a failed update
powerpc/boot: Specify ABI v2 when building an LE boot wrapper
cxl: Fix build failure due to -Wunused-variable behaviour change
cxl: Fix unbalanced pci_dev_get in cxl_probe
powerpc/MSI: Fix race condition in tearing down MSI interrupts
powerpc: Wire up sys_userfaultfd()
powerpc/pseries: Release DRC when configure_connector fails
cxl: abort cxl_pci_enable_device_hook() if PCI channel is offline
powerpc/powernv/pci-ioda: fix kdump with non-power-of-2 crashkernel=
powerpc/powernv/pci-ioda: fix 32-bit TCE table init in kdump kernel
memset() uses instruction dcbz to speed up clearing by not wasting time
loading cache line with data that will be overwritten.
Some platform like mpc52xx do no have cache active at startup and
can therefore not use memset(). Allthough no part of the code
explicitly uses memset(), GCC may make calls to it.
This patch modifies memset() such that at startup, memset()
unconditionally skip the optimised bloc that uses dcbz instruction.
Once the initial MMU is set up, in machine_init() we patch memset()
by replacing this inconditional jump by a NOP
Tested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
memcpy() uses instruction dcbz to speed up copy by not wasting time
loading cache line with data that will be overwritten.
Some platform like mpc52xx do no have cache active at startup and
can therefore not use memcpy(). Allthough no part of the code
explicitly uses memcpy(), GCC makes calls to it.
This patch modifies memcpy() such that at startup, memcpy()
unconditionally jumps to generic_memcpy() which doesn't use
the dcbz instruction.
Once the initial MMU is set up, in machine_init() we patch memcpy()
by replacing this inconditional jump by a NOP
Reported-by: Michal Sojka <sojkam1@fel.cvut.cz>
Tested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Revert dff22d2054 ("PCI: Call pci_read_bridge_bases() from core instead
of arch code").
Reading PCI bridge windows is not arch-specific in itself, but there is PCI
core code that doesn't work correctly if we read them too early. For
example, Hannes found this case on an ARM Freescale i.mx6 board:
pci_bus 0000:00: root bus resource [mem 0x01000000-0x01efffff]
pci 0000:00:00.0: PCI bridge to [bus 01-ff]
pci 0000:00:00.0: BAR 8: no space for [mem size 0x01000000] (mem window)
pci 0000:01:00.0: BAR 2: failed to assign [mem size 0x00200000]
pci 0000:01:00.0: BAR 1: failed to assign [mem size 0x00004000]
pci 0000:01:00.0: BAR 0: failed to assign [mem size 0x00000100]
The 00:00.0 mem window needs to be at least 3MB: the 01:00.0 device needs
0x204100 of space, and mem windows are megabyte-aligned.
Bus sizing can increase a bridge window size, but never *decrease* it (see
d65245c329 ("PCI: don't shrink bridge resources")). Prior to
dff22d2054, ARM didn't read bridge windows at all, so the "original size"
was zero, and we assigned a 3MB window.
After dff22d2054, we read the bridge windows before sizing the bus. The
firmware programmed a 16MB window (size 0x01000000) in 00:00.0, and since
we never decrease the size, we kept 16MB even though we only needed 3MB.
But 16MB doesn't fit in the host bridge aperture, so we failed to assign
space for the window and the downstream devices.
I think this is a defect in the PCI core: we shouldn't rely on the firmware
to assign sensible windows.
Ray reported a similar problem, also on ARM, with Broadcom iProc.
Issues like this are too hard to fix right now, so revert dff22d2054.
Reported-by: Hannes <oe5hpm@gmail.com>
Reported-by: Ray Jui <rjui@broadcom.com>
Link: http://lkml.kernel.org/r/CAAa04yFQEUJm7Jj1qMT57-LG7ZGtnhNDBe=PpSRa70Mj+XhW-A@mail.gmail.com
Link: http://lkml.kernel.org/r/55F75BB8.4070405@broadcom.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
1/ Introduce ZONE_DEVICE and devm_memremap_pages() as a generic
mechanism for adding device-driver-discovered memory regions to the
kernel's direct map. This facility is used by the pmem driver to
enable pfn_to_page() operations on the page frames returned by DAX
('direct_access' in 'struct block_device_operations'). For now, the
'memmap' allocation for these "device" pages comes from "System
RAM". Support for allocating the memmap from device memory will
arrive in a later kernel.
2/ Introduce memremap() to replace usages of ioremap_cache() and
ioremap_wt(). memremap() drops the __iomem annotation for these
mappings to memory that do not have i/o side effects. The
replacement of ioremap_cache() with memremap() is limited to the
pmem driver to ease merging the api change in v4.3. Completion of
the conversion is targeted for v4.4.
3/ Similar to the usage of memcpy_to_pmem() + wmb_pmem() in the pmem
driver, update the VFS DAX implementation and PMEM api to provide
persistence guarantees for kernel operations on a DAX mapping.
4/ Convert the ACPI NFIT 'BLK' driver to map the block apertures as
cacheable to improve performance.
5/ Miscellaneous updates and fixes to libnvdimm including support
for issuing "address range scrub" commands, clarifying the optimal
'sector size' of pmem devices, a clarification of the usage of the
ACPI '_STA' (status) property for DIMM devices, and other minor
fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=o57/
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"This update has successfully completed a 0day-kbuild run and has
appeared in a linux-next release. The changes outside of the typical
drivers/nvdimm/ and drivers/acpi/nfit.[ch] paths are related to the
removal of IORESOURCE_CACHEABLE, the introduction of memremap(), and
the introduction of ZONE_DEVICE + devm_memremap_pages().
Summary:
- Introduce ZONE_DEVICE and devm_memremap_pages() as a generic
mechanism for adding device-driver-discovered memory regions to the
kernel's direct map.
This facility is used by the pmem driver to enable pfn_to_page()
operations on the page frames returned by DAX ('direct_access' in
'struct block_device_operations').
For now, the 'memmap' allocation for these "device" pages comes
from "System RAM". Support for allocating the memmap from device
memory will arrive in a later kernel.
- Introduce memremap() to replace usages of ioremap_cache() and
ioremap_wt(). memremap() drops the __iomem annotation for these
mappings to memory that do not have i/o side effects. The
replacement of ioremap_cache() with memremap() is limited to the
pmem driver to ease merging the api change in v4.3.
Completion of the conversion is targeted for v4.4.
- Similar to the usage of memcpy_to_pmem() + wmb_pmem() in the pmem
driver, update the VFS DAX implementation and PMEM api to provide
persistence guarantees for kernel operations on a DAX mapping.
- Convert the ACPI NFIT 'BLK' driver to map the block apertures as
cacheable to improve performance.
- Miscellaneous updates and fixes to libnvdimm including support for
issuing "address range scrub" commands, clarifying the optimal
'sector size' of pmem devices, a clarification of the usage of the
ACPI '_STA' (status) property for DIMM devices, and other minor
fixes"
* tag 'libnvdimm-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (34 commits)
libnvdimm, pmem: direct map legacy pmem by default
libnvdimm, pmem: 'struct page' for pmem
libnvdimm, pfn: 'struct page' provider infrastructure
x86, pmem: clarify that ARCH_HAS_PMEM_API implies PMEM mapped WB
add devm_memremap_pages
mm: ZONE_DEVICE for "device memory"
mm: move __phys_to_pfn and __pfn_to_phys to asm/generic/memory_model.h
dax: drop size parameter to ->direct_access()
nd_blk: change aperture mapping from WC to WB
nvdimm: change to use generic kvfree()
pmem, dax: have direct_access use __pmem annotation
dax: update I/O path to do proper PMEM flushing
pmem: add copy_from_iter_pmem() and clear_pmem()
pmem, x86: clean up conditional pmem includes
pmem: remove layer when calling arch_has_wmb_pmem()
pmem, x86: move x86 PMEM API to new pmem.h header
libnvdimm, e820: make CONFIG_X86_PMEM_LEGACY a tristate option
pmem: switch to devm_ allocations
devres: add devm_memremap
libnvdimm, btt: write and validate parent_uuid
...
- Support "hybrid" iommu/direct DMA ops for coherent_mask < dma_mask from Benjamin Herrenschmidt
- EEH fixes for SRIOV from Gavin
- Introduce rtas_get_sensor_fast() for IRQ handlers from Thomas Huth
- Use hardware RNG for arch_get_random_seed_* not arch_get_random_* from Paul Mackerras
- Seccomp filter support from Michael Ellerman
- opal_cec_reboot2() handling for HMIs & machine checks from Mahesh Salgaonkar
- Add powerpc timebase as a trace clock source from Naveen N. Rao
- Misc cleanups in the xmon, signal & SLB code from Anshuman Khandual
- Add an inline function to update POWER8 HID0 from Gautham R. Shenoy
- Fix pte_pagesize_index() crash on 4K w/64K hash from Michael Ellerman
- Drop support for 64K local store on 4K kernels from Michael Ellerman
- move dma_get_required_mask() from pnv_phb to pci_controller_ops from Andrew Donnellan
- Initialize distance lookup table from drconf path from Nikunj A Dadhania
- Enable RTC class support from Vaibhav Jain
- Disable automatically blocked PCI config from Gavin Shan
- Add LEDs driver for PowerNV platform from Vasant Hegde
- Fix endianness issues in the HVSI driver from Laurent Dufour
- Kexec endian fixes from Samuel Mendoza-Jonas
- Fix corrupted pdn list from Gavin Shan
- Fix fenced PHB caused by eeh_slot_error_detail() from Gavin Shan
- Freescale updates from Scott: Highlights include 32-bit memcpy/memset
optimizations, checksum optimizations, 85xx config fragments and updates,
device tree updates, e6500 fixes for non-SMP, and misc cleanup and minor
fixes.
- A ton of cxl updates & fixes:
- Add explicit precision specifiers from Rasmus Villemoes
- use more common format specifier from Rasmus Villemoes
- Destroy cxl_adapter_idr on module_exit from Johannes Thumshirn
- Destroy afu->contexts_idr on release of an afu from Johannes Thumshirn
- Compile with -Werror from Daniel Axtens
- EEH support from Daniel Axtens
- Plug irq_bitmap getting leaked in cxl_context from Vaibhav Jain
- Add alternate MMIO error handling from Ian Munsie
- Allow release of contexts which have been OPENED but not STARTED from Andrew Donnellan
- Remove use of macro DEFINE_PCI_DEVICE_TABLE from Vaishali Thakkar
- Release irqs if memory allocation fails from Vaibhav Jain
- Remove racy attempt to force EEH invocation in reset from Daniel Axtens
- Fix + cleanup error paths in cxl_dev_context_init from Ian Munsie
- Fix force unmapping mmaps of contexts allocated through the kernel api from Ian Munsie
- Set up and enable PSL Timebase from Philippe Bergheaud
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=n9+X
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- support "hybrid" iommu/direct DMA ops for coherent_mask < dma_mask
from Benjamin Herrenschmidt
- EEH fixes for SRIOV from Gavin
- introduce rtas_get_sensor_fast() for IRQ handlers from Thomas Huth
- use hardware RNG for arch_get_random_seed_* not arch_get_random_*
from Paul Mackerras
- seccomp filter support from Michael Ellerman
- opal_cec_reboot2() handling for HMIs & machine checks from Mahesh
Salgaonkar
- add powerpc timebase as a trace clock source from Naveen N. Rao
- misc cleanups in the xmon, signal & SLB code from Anshuman Khandual
- add an inline function to update POWER8 HID0 from Gautham R. Shenoy
- fix pte_pagesize_index() crash on 4K w/64K hash from Michael Ellerman
- drop support for 64K local store on 4K kernels from Michael Ellerman
- move dma_get_required_mask() from pnv_phb to pci_controller_ops from
Andrew Donnellan
- initialize distance lookup table from drconf path from Nikunj A
Dadhania
- enable RTC class support from Vaibhav Jain
- disable automatically blocked PCI config from Gavin Shan
- add LEDs driver for PowerNV platform from Vasant Hegde
- fix endianness issues in the HVSI driver from Laurent Dufour
- kexec endian fixes from Samuel Mendoza-Jonas
- fix corrupted pdn list from Gavin Shan
- fix fenced PHB caused by eeh_slot_error_detail() from Gavin Shan
- Freescale updates from Scott: Highlights include 32-bit memcpy/memset
optimizations, checksum optimizations, 85xx config fragments and
updates, device tree updates, e6500 fixes for non-SMP, and misc
cleanup and minor fixes.
- a ton of cxl updates & fixes:
- add explicit precision specifiers from Rasmus Villemoes
- use more common format specifier from Rasmus Villemoes
- destroy cxl_adapter_idr on module_exit from Johannes Thumshirn
- destroy afu->contexts_idr on release of an afu from Johannes
Thumshirn
- compile with -Werror from Daniel Axtens
- EEH support from Daniel Axtens
- plug irq_bitmap getting leaked in cxl_context from Vaibhav Jain
- add alternate MMIO error handling from Ian Munsie
- allow release of contexts which have been OPENED but not STARTED
from Andrew Donnellan
- remove use of macro DEFINE_PCI_DEVICE_TABLE from Vaishali Thakkar
- release irqs if memory allocation fails from Vaibhav Jain
- remove racy attempt to force EEH invocation in reset from Daniel
Axtens
- fix + cleanup error paths in cxl_dev_context_init from Ian Munsie
- fix force unmapping mmaps of contexts allocated through the kernel
api from Ian Munsie
- set up and enable PSL Timebase from Philippe Bergheaud
* tag 'powerpc-4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (140 commits)
cxl: Set up and enable PSL Timebase
cxl: Fix force unmapping mmaps of contexts allocated through the kernel api
cxl: Fix + cleanup error paths in cxl_dev_context_init
powerpc/eeh: Fix fenced PHB caused by eeh_slot_error_detail()
powerpc/pseries: Cleanup on pci_dn_reconfig_notifier()
powerpc/pseries: Fix corrupted pdn list
powerpc/powernv: Enable LEDS support
powerpc/iommu: Set default DMA offset in dma_dev_setup
cxl: Remove racy attempt to force EEH invocation in reset
cxl: Release irqs if memory allocation fails
cxl: Remove use of macro DEFINE_PCI_DEVICE_TABLE
powerpc/powernv: Fix mis-merge of OPAL support for LEDS driver
powerpc/powernv: Reset HILE before kexec_sequence()
powerpc/kexec: Reset secondary cpu endianness before kexec
powerpc/hvsi: Fix endianness issues in the HVSI driver
leds/powernv: Add driver for PowerNV platform
powerpc/powernv: Create LED platform device
powerpc/powernv: Add OPAL interfaces for accessing and modifying system LED states
powerpc/powernv: Fix the log message when disabling VF
cxl: Allow release of contexts which have been OPENED but not STARTED
...
Pull locking and atomic updates from Ingo Molnar:
"Main changes in this cycle are:
- Extend atomic primitives with coherent logic op primitives
(atomic_{or,and,xor}()) and deprecate the old partial APIs
(atomic_{set,clear}_mask())
The old ops were incoherent with incompatible signatures across
architectures and with incomplete support. Now every architecture
supports the primitives consistently (by Peter Zijlstra)
- Generic support for 'relaxed atomics':
- _acquire/release/relaxed() flavours of xchg(), cmpxchg() and {add,sub}_return()
- atomic_read_acquire()
- atomic_set_release()
This came out of porting qwrlock code to arm64 (by Will Deacon)
- Clean up the fragile static_key APIs that were causing repeat bugs,
by introducing a new one:
DEFINE_STATIC_KEY_TRUE(name);
DEFINE_STATIC_KEY_FALSE(name);
which define a key of different types with an initial true/false
value.
Then allow:
static_branch_likely()
static_branch_unlikely()
to take a key of either type and emit the right instruction for the
case. To be able to know the 'type' of the static key we encode it
in the jump entry (by Peter Zijlstra)
- Static key self-tests (by Jason Baron)
- qrwlock optimizations (by Waiman Long)
- small futex enhancements (by Davidlohr Bueso)
- ... and misc other changes"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (63 commits)
jump_label/x86: Work around asm build bug on older/backported GCCs
locking, ARM, atomics: Define our SMP atomics in terms of _relaxed() operations
locking, include/llist: Use linux/atomic.h instead of asm/cmpxchg.h
locking/qrwlock: Make use of _{acquire|release|relaxed}() atomics
locking/qrwlock: Implement queue_write_unlock() using smp_store_release()
locking/lockref: Remove homebrew cmpxchg64_relaxed() macro definition
locking, asm-generic: Add _{relaxed|acquire|release}() variants for 'atomic_long_t'
locking, asm-generic: Rework atomic-long.h to avoid bulk code duplication
locking/atomics: Add _{acquire|release|relaxed}() variants of some atomic operations
locking, compiler.h: Cast away attributes in the WRITE_ONCE() magic
locking/static_keys: Make verify_keys() static
jump label, locking/static_keys: Update docs
locking/static_keys: Provide a selftest
jump_label: Provide a self-test
s390/uaccess, locking/static_keys: employ static_branch_likely()
x86, tsc, locking/static_keys: Employ static_branch_likely()
locking/static_keys: Add selftest
locking/static_keys: Add a new static_key interface
locking/static_keys: Rework update logic
locking/static_keys: Add static_key_{en,dis}able() helpers
...
Pull timer updates from Thomas Gleixner:
"Rather large, but nothing exiting:
- new range check for settimeofday() to prevent that boot time
becomes negative.
- fix for file time rounding
- a few simplifications of the hrtimer code
- fix for the proc/timerlist code so the output of clock realtime
timers is accurate
- more y2038 work
- tree wide conversion of clockevent drivers to the new callbacks"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (88 commits)
hrtimer: Handle failure of tick_init_highres() gracefully
hrtimer: Unconfuse switch_hrtimer_base() a bit
hrtimer: Simplify get_target_base() by returning current base
hrtimer: Drop return code of hrtimer_switch_to_hres()
time: Introduce timespec64_to_jiffies()/jiffies_to_timespec64()
time: Introduce current_kernel_time64()
time: Introduce struct itimerspec64
time: Add the common weak version of update_persistent_clock()
time: Always make sure wall_to_monotonic isn't positive
time: Fix nanosecond file time rounding in timespec_trunc()
timer_list: Add the base offset so remaining nsecs are accurate for non monotonic timers
cris/time: Migrate to new 'set-state' interface
kernel: broadcast-hrtimer: Migrate to new 'set-state' interface
xtensa/time: Migrate to new 'set-state' interface
unicore/time: Migrate to new 'set-state' interface
um/time: Migrate to new 'set-state' interface
sparc/time: Migrate to new 'set-state' interface
sh/localtimer: Migrate to new 'set-state' interface
score/time: Migrate to new 'set-state' interface
s390/time: Migrate to new 'set-state' interface
...
The config space of some PCI devices can't be accessed when their
PEs are in frozen state. Otherwise, fenced PHB might be seen.
Those PEs are identified with flag EEH_PE_CFG_RESTRICTED, meaing
EEH_PE_CFG_BLOCKED is set automatically when the PE is put to
frozen state (EEH_PE_ISOLATED). eeh_slot_error_detail() restores
PCI device BARs with eeh_pe_restore_bars(), which then calls
eeh_ops->restore_config() to reinitialize the PCI device in
(OPAL) firmware. eeh_ops->restore_config() produces PCI config
access that causes fenced PHB. The problem was reported on below
adapter:
0001:01:00.0 0200: 14e4:168e (rev 10)
0001:01:00.0 Ethernet controller: Broadcom Corporation \
NetXtreme II BCM57810 10 Gigabit Ethernet (rev 10)
This fixes the issue by skipping eeh_pe_restore_bars() in
eeh_slot_error_detail() when EEH_PE_CFG_BLOCKED is set for the PE.
Fixes: b6541db1 ("powerpc/eeh: Block PCI config access upon frozen PE")
Cc: stable@vger.kernel.org # v4.0+
Reported-by: Manvanthara B. Puttashankar <mputtash@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Freescale updates from Scott:
"Highlights include 32-bit memcpy/memset optimizations, checksum
optimizations, 85xx config fragments and updates, device tree updates,
e6500 fixes for non-SMP, and misc cleanup and minor fixes."
Since commit 1851617cd2 ("PCI/MSI: Disable MSI at enumeration even if
kernel doesn't support MSI"), the setup of dev->msi_cap/msix_cap and the
disable of MSI/MSI-X interrupts isn't being done at PCI probe time, as
the logic responsible for this was moved in the aforementioned commit
from pci_device_add() to pci_setup_device(). The latter function is not
reachable on PowerPC pseries platform during Open Firmware PCI probing
time.
This exhibits as drivers not being able to enable MSI, eg:
bnx2x 0000:01:00.0: no msix capability found
This patch calls pci_msi_setup_pci_dev() explicitly to disable MSI/MSI-X
during PCI probe time on pSeries platform.
Fixes: 1851617cd2 ("PCI/MSI: Disable MSI at enumeration even if kernel doesn't support MSI")
[mpe: Flesh out change log and clarify comment]
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This builds on the ability to run more than one vcore on a physical
core by using the micro-threading (split-core) modes of the POWER8
chip. Previously, only vcores from the same VM could be run together,
and (on POWER8) only if they had just one thread per core. With the
ability to split the core on guest entry and unsplit it on guest exit,
we can run up to 8 vcpu threads from up to 4 different VMs, and we can
run multiple vcores with 2 or 4 vcpus per vcore.
Dynamic micro-threading is only available if the static configuration
of the cores is whole-core mode (unsplit), and only on POWER8.
To manage this, we introduce a new kvm_split_mode struct which is
shared across all of the subcores in the core, with a pointer in the
paca on each thread. In addition we extend the core_info struct to
have information on each subcore. When deciding whether to add a
vcore to the set already on the core, we now have two possibilities:
(a) piggyback the vcore onto an existing subcore, or (b) start a new
subcore.
Currently, when any vcpu needs to exit the guest and switch to host
virtual mode, we interrupt all the threads in all subcores and switch
the core back to whole-core mode. It may be possible in future to
allow some of the subcores to keep executing in the guest while
subcore 0 switches to the host, but that is not implemented in this
patch.
This adds a module parameter called dynamic_mt_modes which controls
which micro-threading (split-core) modes the code will consider, as a
bitmap. In other words, if it is 0, no micro-threading mode is
considered; if it is 2, only 2-way micro-threading is considered; if
it is 4, only 4-way, and if it is 6, both 2-way and 4-way
micro-threading mode will be considered. The default is 6.
With this, we now have secondary threads which are the primary thread
for their subcore and therefore need to do the MMU switch. These
threads will need to be started even if they have no vcpu to run, so
we use the vcore pointer in the PACA rather than the vcpu pointer to
trigger them.
It is now possible for thread 0 to find that an exit has been
requested before it gets to switch the subcore state to the guest. In
that case we haven't added the guest's timebase offset to the
timebase, so we need to be careful not to subtract the offset in the
guest exit path. In fact we just skip the whole path that switches
back to host context, since we haven't switched to the guest context.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
When running a virtual core of a guest that is configured with fewer
threads per core than the physical cores have, the extra physical
threads are currently unused. This makes it possible to use them to
run one or more other virtual cores from the same guest when certain
conditions are met. This applies on POWER7, and on POWER8 to guests
with one thread per virtual core. (It doesn't apply to POWER8 guests
with multiple threads per vcore because they require a 1-1 virtual to
physical thread mapping in order to be able to use msgsndp and the
TIR.)
The idea is that we maintain a list of preempted vcores for each
physical cpu (i.e. each core, since the host runs single-threaded).
Then, when a vcore is about to run, it checks to see if there are
any vcores on the list for its physical cpu that could be
piggybacked onto this vcore's execution. If so, those additional
vcores are put into state VCORE_PIGGYBACK and their runnable VCPU
threads are started as well as the original vcore, which is called
the master vcore.
After the vcores have exited the guest, the extra ones are put back
onto the preempted list if any of their VCPUs are still runnable and
not idle.
This means that vcpu->arch.ptid is no longer necessarily the same as
the physical thread that the vcpu runs on. In order to make it easier
for code that wants to send an IPI to know which CPU to target, we
now store that in a new field in struct vcpu_arch, called thread_cpu.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Tested-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
If the target kernel does not inlcude the FIXUP_ENDIAN check, coming
from a different-endian kernel will cause the target kernel to panic.
All ppc64 kernels can handle starting in big-endian mode, so return to
big-endian before branching into the target kernel.
This mainly affects pseries as secondaries on powernv are returned to
OPAL.
Signed-off-by: Samuel Mendoza-Jonas <sam.mj@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pstore only supports one backend at a time. The preferred
pstore backend is set by passing the pstore.backend=<name>
argument to the kernel at boot time. Currently, while trying
to register with pstore, nvram throws an error message even
when "pstore.backend != nvram", which is unnecessary. This
patch removes the error message in case "pstore.backend != nvram".
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The patch was generated using fixed coccinelle semantic patch
scripts/coccinelle/api/memdup.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2014320
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
pcibios_set_pcie_reset_state() could be called to complete
reset request when passing through PCI device, flag
EEH_PE_ISOLATED is set before saving the PCI config sapce.
On some Broadcom adapters, EEH_PE_CFG_BLOCKED is automatically
set when the flag EEH_PE_ISOLATED is marked. It caused bogus
data saved from the PCI config space, which will be restored
to the PCI adapter after the reset. Eventually, the hardware
can't work with corrupted data in PCI config space.
The patch fixes the issue with eeh_pe_state_mark_no_cfg(), which
doesn't set EEH_PE_CFG_BLOCKED when seeing EEH_PE_ISOLATED on the
PE, in order to avoid the bogus data saved and restored to the PCI
config space.
Reported-by: Rajanikanth H. Adaveeshaiah <rajanikanth.ha@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Simplify the dma_get_required_mask call chain by moving it from pnv_phb to
pci_controller_ops, similar to commit 763d2d8df1 ("powerpc/powernv:
Move dma_set_mask from pnv_phb to pci_controller_ops").
Previous call chain:
0) call dma_get_required_mask() (kernel/dma.c)
1) call ppc_md.dma_get_required_mask, if it exists. On powernv, that
points to pnv_dma_get_required_mask() (platforms/powernv/setup.c)
2) device is PCI, therefore call pnv_pci_dma_get_required_mask()
(platforms/powernv/pci.c)
3) call phb->dma_get_required_mask if it exists
4) it only exists in the ioda case, where it points to
pnv_pci_ioda_dma_get_required_mask() (platforms/powernv/pci-ioda.c)
New call chain:
0) call dma_get_required_mask() (kernel/dma.c)
1) device is PCI, therefore call pci_controller_ops.dma_get_required_mask
if it exists
2) in the ioda case, that points to pnv_pci_ioda_dma_get_required_mask()
(platforms/powernv/pci-ioda.c)
In the p5ioc2 case, the call chain remains the same -
dma_get_required_mask() does not find either a ppc_md call or
pci_controller_ops call, so it calls __dma_get_required_mask().
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since we moved the "lock" to be the first element of
struct tlb_core_data in commit 82d86de25b ("powerpc/e6500: Make TLB
lock recursive"), this macro is not used by any code. Just delete it.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
* pci/hotplug:
PCI: pciehp: Remove ignored MRL sensor interrupt events
PCI: pciehp: Remove unused interrupt events
PCI: pciehp: Handle invalid data when reading from non-existent devices
PCI: Hold pci_slot_mutex while searching bus->slots list
PCI: Protect pci_bus->slots with pci_slot_mutex, not pci_bus_sem
PCI: pciehp: Simplify pcie_poll_cmd()
PCI: Use "slot" and "pci_slot" for struct hotplug_slot and struct pci_slot
* pci/iommu:
PCI: Remove pci_ats_enabled()
PCI: Stop caching ATS Invalidate Queue Depth
PCI: Move ATS declarations to linux/pci.h so they're all together
PCI: Clean up ATS error handling
PCI: Use pci_physfn() rather than looking up physfn by hand
PCI: Inline the ATS setup code into pci_ats_init()
PCI: Rationalize pci_ats_queue_depth() error checking
PCI: Reduce size of ATS structure elements
PCI: Embed ATS info directly into struct pci_dev
PCI: Allocate ATS struct during enumeration
iommu/vt-d: Cache PCI ATS state and Invalidate Queue Depth
* pci/irq:
PCI: Kill off set_irq_flags() usage
* pci/virtualization:
PCI: Add ACS quirks for Intel I219-LM/V
In the complete hotplug case, EEH PEs are supposed to be released
and set to NULL. Normally, this is done by eeh_remove_device(),
which is called from pcibios_release_device().
However, if something is holding a kref to the device, it will not
be released, and the PE will remain. eeh_add_device_late() has
a check for this which will explictly destroy the PE in this case.
This check in eeh_add_device_late() occurs after a call to
eeh_ops->probe(). On PowerNV, probe is a pointer to pnv_eeh_probe(),
which will exit without probing if there is an existing PE.
This means that on PowerNV, devices with outstanding krefs will not
be rediscovered by EEH correctly after a complete hotplug. This is
affecting CXL (CAPI) devices in the field.
Put the probe after the kref check so that the PE is destroyed
and affected devices are correctly rediscovered by EEH.
Fixes: d91dafc02f ("powerpc/eeh: Delay probing EEH device during hotplug")
Cc: stable@vger.kernel.org
Cc: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Replace hard coded values with existing DRCONF flags while procesing
detected LMBs from the device tree. Does not change any functionality.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The code to fetch the SLB size from the device tree wants to first look
for "slb-size" and then if that's not found "ibm,slb-size".
We can simplify the code by looking for the properties and then if we
find one of them we set mmu_slb_size.
We also change the function name from check_cpu_slb_size() to
init_mmu_slb_size() as the function doesn't check anything, it only
initialises mmu_slb_size.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
[mpe: Rewrite change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Quoting Arnd:
I was thinking the opposite approach and basically removing all uses
of IORESOURCE_CACHEABLE from the kernel. There are only a handful of
them.and we can probably replace them all with hardcoded
ioremap_cached() calls in the cases they are actually useful.
All existing usages of IORESOURCE_CACHEABLE call ioremap() instead of
ioremap_nocache() if the resource is cacheable, however ioremap() is
uncached by default. Clearly none of the existing usages care about the
cacheability. Particularly devm_ioremap_resource() never worked as
advertised since it always fell back to plain ioremap().
Clean this up as the new direction we want is to convert
ioremap_<type>() usages to memremap(..., flags).
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Migrate powerpc driver to the new 'set-state' interface provided by
clockevents core, the earlier 'set-mode' interface is marked obsolete
now.
This also enables us to implement callbacks for new states of clockevent
devices, for example: ONESHOT_STOPPED.
We weren't doing anything in ->set_mode(ONSHOT) and so
set_state_oneshot() isn't implemented.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
In CoreNet systems it is not allowed to mix M and non-M mappings to the
same memory, and coherent DMA accesses are considered to be M mappings
for this purpose. Ignoring this has been observed to cause hard
lockups in non-SMP kernels on e6500.
Furthermore, e6500 implements the LRAT (logical to real address table)
which allows KVM guests to control the WIMGE bits. This means that
KVM cannot force the M bit on the way it usually does, so the guest had
better set it itself.
Signed-off-by: Scott Wood <scottwood@freescale.com>
This function can leak kernel stack data when the user siginfo_t has a
positive si_code value. The top 16 bits of si_code descibe which fields
in the siginfo_t union are active, but they are treated inconsistently
between copy_siginfo_from_user32, copy_siginfo_to_user32 and
copy_siginfo_to_user.
copy_siginfo_from_user32 is called from rt_sigqueueinfo and
rt_tgsigqueueinfo in which the user has full control overthe top 16 bits
of si_code.
This fixes the following information leaks:
x86: 8 bytes leaked when sending a signal from a 32-bit process to
itself. This leak grows to 16 bytes if the process uses x32.
(si_code = __SI_CHLD)
x86: 100 bytes leaked when sending a signal from a 32-bit process to
a 64-bit process. (si_code = -1)
sparc: 4 bytes leaked when sending a signal from a 32-bit process to a
64-bit process. (si_code = any)
parsic and s390 have similar bugs, but they are not vulnerable because
rt_[tg]sigqueueinfo have checks that prevent sending a positive si_code
to a different process. These bugs are also fixed for consistency.
Signed-off-by: Amanieu d'Antras <amanieu@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a new powerpc-specific trace clock using the timebase register,
similar to x86-tsc. This gives us
- a fast, monotonic, hardware clock source for trace entries, and
- a clock that can be used to correlate events across cpus as well as across
hypervisor and guests.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use %pR to simplify the debug code. This also make the debug info more
readable.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
[mpe: Unsplit multi-line printk strings]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since we've already stepped away from ENABLE is a JMP and DISABLE is a
NOP with the branch_default bits, and are going to make it even worse,
rename it to make it all clearer.
This way we don't mix multiple levels of logic attributes, but have a
plain 'physical' name for what the current instruction patching status
of a jump label is.
This is a first step in removing the naming confusion that has led to
a stream of avoidable bugs such as:
a833581e37 ("x86, perf: Fix static_key bug in load_mm_cr4()")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
[ Beefed up the changelog. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Previously, pci_setup_device() and similar functions searched the
pci_bus->slots list without any locking. It was possible for another
thread to update the list while we searched it.
Add pci_dev_assign_slot() to search the list while holding pci_slot_mutex.
[bhelgaas: changelog, fold in CONFIG_SYSFS fix]
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This commit enables seccomp filter on powerpc, now that we have all the
necessary pieces in place.
To support seccomp's desire to modify the syscall return value under
some circumstances, we use a different ABI to the ptrace ABI. That is we
use r3 as the syscall return value, and orig_gpr3 is the first syscall
parameter.
This means the seccomp code, or a ptracer via SECCOMP_RET_TRACE, will
see -ENOSYS preloaded in r3. This is identical to the behaviour on x86,
and allows seccomp or the ptracer to either leave the -ENOSYS or change
it to something else, as well as rejecting or not the syscall by
modifying r0.
If seccomp does not reject the syscall, we restore the register state to
match what ptrace and audit expect, ie. r3 is the first syscall
parameter again. We do this restore using orig_gpr3, which may have been
modified by seccomp, which allows seccomp to modify the first syscall
paramater and allow the syscall to proceed.
We need to #ifdef the the additional handling of r3 for seccomp, so move
it all out of line.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Kees Cook <keescook@chromium.org>
SIG_SYS was added in commit a0727e8ce5 "signal, x86: add SIGSYS info
and make it synchronous."
Because we use the asm-generic struct siginfo, we got support for
SIG_SYS for free as part of that commit.
However there was no compat handling added for powerpc. That means we've
been advertising the existence of signfo._sifields._sigsys to compat
tasks, but not actually filling in the fields correctly.
Luckily it looks like no one has noticed, presumably because the only
user of SIGSYS in the kernel is seccomp filter, which we don't support
yet.
So before we enable seccomp filter, add compat handling for SIGSYS.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Kees Cook <keescook@chromium.org>
The API for calling do_syscall_trace_enter() is currently sensible
enough, it just returns the (modified) syscall number.
However once we enable seccomp filter it will get more complicated. When
seccomp filter runs, the seccomp kernel code (via SECCOMP_RET_ERRNO), or
a ptracer (via SECCOMP_RET_TRACE), may reject the syscall and *may* or may
*not* set a return value in r3.
That means the assembler that calls do_syscall_trace_enter() can not
blindly return ENOSYS, it needs to only return ENOSYS if a return value
has not already been set.
There is no way to implement that logic with the current API. So change
the do_syscall_trace_enter() API to make it deal with the return code
juggling, and the assembler can then just return whatever return code it
is given.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Kees Cook <keescook@chromium.org>
Currently on powerpc we have our own #define for the highest (negative)
errno value, called _LAST_ERRNO. This is defined to be 516, for reasons
which are not clear.
The generic code, and x86, use MAX_ERRNO, which is defined to be 4095.
In particular seccomp uses MAX_ERRNO to restrict the value that a
seccomp filter can return.
Currently with the mismatch between _LAST_ERRNO and MAX_ERRNO, a seccomp
tracer wanting to return 600, expecting it to be seen as an error, would
instead find on powerpc that userspace sees a successful syscall with a
return value of 600.
To avoid this inconsistency, switch powerpc to use MAX_ERRNO.
We are somewhat confident that generic syscalls that can return a
non-error value above negative MAX_ERRNO have already been updated to
use force_successful_syscall_return().
I have also checked all the powerpc specific syscalls, and believe that
none of them expect to return a non-error value between -MAX_ERRNO and
-516. So this change should be safe ...
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Kees Cook <keescook@chromium.org>
Move the now generic definitions of atomic_{set,clear}_mask() into
linux/atomic.h to avoid endless and pointless repetition.
Also, provide an atomic_andnot() wrapper for those few archs that can
implement that.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When we scan a PCI bus, we read PCI-PCI bridge window registers with
pci_read_bridge_bases() so we can validate the resource hierarchy. Most
architectures call pci_read_bridge_bases() from pcibios_fixup_bus(), but
PCI-PCI bridges are not arch-specific, so this doesn't need to be in
arch-specific code.
Call pci_read_bridge_bases() directly from the PCI core instead of from
arch code.
For alpha and mips, we now call pci_read_bridge_bases() always; previously
we only called it if PCI_PROBE_ONLY was set.
[bhelgaas: changelog]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Ralf Baechle <ralf@linux-mips.org>
CC: James E.J. Bottomley <jejb@parisc-linux.org>
CC: Michael Ellerman <mpe@ellerman.id.au>
CC: Bjorn Helgaas <bhelgaas@google.com>
CC: Richard Henderson <rth@twiddle.net>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: David Howells <dhowells@redhat.com>
CC: Russell King <linux@arm.linux.org.uk>
CC: Tony Luck <tony.luck@intel.com>
CC: David S. Miller <davem@davemloft.net>
CC: Ingo Molnar <mingo@redhat.com>
CC: Guenter Roeck <linux@roeck-us.net>
CC: Michal Simek <monstr@monstr.eu>
CC: Chris Zankel <chris@zankel.net>
The EPOW interrupt handler uses rtas_get_sensor(), which in turn
uses rtas_busy_delay() to wait for RTAS becoming ready in case it
is necessary. But rtas_busy_delay() is annotated with might_sleep()
and thus may not be used by interrupts handlers like the EPOW handler!
This leads to the following BUG when CONFIG_DEBUG_ATOMIC_SLEEP is
enabled:
BUG: sleeping function called from invalid context at arch/powerpc/kernel/rtas.c:496
in_atomic(): 1, irqs_disabled(): 1, pid: 0, name: swapper/1
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.2.0-rc2-thuth #6
Call Trace:
[c00000007ffe7b90] [c000000000807670] dump_stack+0xa0/0xdc (unreliable)
[c00000007ffe7bc0] [c0000000000e1f14] ___might_sleep+0x134/0x180
[c00000007ffe7c20] [c00000000002aec0] rtas_busy_delay+0x30/0xd0
[c00000007ffe7c50] [c00000000002bde4] rtas_get_sensor+0x74/0xe0
[c00000007ffe7ce0] [c000000000083264] ras_epow_interrupt+0x44/0x450
[c00000007ffe7d90] [c000000000120260] handle_irq_event_percpu+0xa0/0x300
[c00000007ffe7e70] [c000000000120524] handle_irq_event+0x64/0xc0
[c00000007ffe7eb0] [c000000000124dbc] handle_fasteoi_irq+0xec/0x260
[c00000007ffe7ef0] [c00000000011f4f0] generic_handle_irq+0x50/0x80
[c00000007ffe7f20] [c000000000010f3c] __do_irq+0x8c/0x200
[c00000007ffe7f90] [c0000000000236cc] call_do_irq+0x14/0x24
[c00000007e6f39e0] [c000000000011144] do_IRQ+0x94/0x110
[c00000007e6f3a30] [c000000000002594] hardware_interrupt_common+0x114/0x180
Fix this issue by introducing a new rtas_get_sensor_fast() function
that does not use rtas_busy_delay() - and thus can only be used for
sensors that do not cause a BUSY condition - known as "fast" sensors.
The EPOW sensor is defined to be "fast" in sPAPR - mpe.
Fixes: 587f83e8dd ("powerpc/pseries: Use rtas_get_sensor in RAS code")
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
rtas.h already has some nice #defines for RTAS return status
codes - let's use them instead of hard-coded "magic" values!
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds one helper function 'sigcontext_vmx_regs' which computes
quad word aligned pointer for 'vmx_reserve' array element in sigcontext
structure making the code more readable.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
[mpe: Reword comment and fix build for CONFIG_ALTIVEC=n]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently tm_orig_msr is getting used during process context switch only.
Then there is ckpt_regs which saves the checkpointed userspace context
The MSR slot contained in ckpt_regs structure can be used during process
context switch instead of tm_orig_msr, thus allowing us to drop it from
thread_struct structure. This patch does that change.
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
enable_kernel_vsx() function was commented since anything was using
it. However, vmx-crypto driver uses VSX instructions which are
only available if VSX is enable. Otherwise it rises an exception oops.
This patch uncomment enable_kernel_vsx() routine and makes it available.
Signed-off-by: Leonidas S. Barbosa <leosilva@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The encoding of the lengths in the ibm_architecture_vec array is
"interesting" to say the least. It's non-obvious how the number of bytes
we provide relates to the length value.
In fact we already got it wrong once, see 11e9ed43ca "Fix up
ibm_architecture_vec definition".
So add some macros to make it (hopefully) clearer. These at least have
the property that the integer present in the code is equal to the number
of bytes that follows it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Stewart Smith <stewart@linux.vnet.ibm.com>
This patch adds the ability to the DMA direct ops to fallback to the IOMMU
ops for coherent alloc/free if the coherent mask of the device isn't
suitable for accessing the direct DMA space and the device also happens
to have an active IOMMU table.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
core_idle_state is maintained for each core. It uses 0-7 bits to track
whether a thread in the core has entered fastsleep or winkle. 8th bit is
used as a lock bit.
The lock bit is set in these 2 scenarios-
- The thread is first in subcore to wakeup from sleep/winkle.
- If its the last thread in the core about to enter sleep/winkle
While the lock bit is set, if any other thread in the core wakes up, it
loops until the lock bit is cleared before proceeding in the wakeup
path. This helps prevent race conditions w.r.t fastsleep workaround and
prevents threads from switching to process context before core/subcore
resources are restored.
But, in the path to sleep/winkle entry, we currently don't check for
lock-bit. This exposes us to following race when running with subcore
on-
First thread in the subcorea Another thread in the same
waking up core entering sleep/winkle
lwarx r15,0,r14
ori r15,r15,PNV_CORE_IDLE_LOCK_BIT
stwcx. r15,0,r14
[Code to restore subcore state]
lwarx r15,0,r14
[clear thread bit]
stwcx. r15,0,r14
andi. r15,r15,PNV_CORE_IDLE_THREAD_BITS
stw r15,0(r14)
Here, after the thread entering sleep clears its thread bit in
core_idle_state, the value is overwritten by the thread waking up.
In such cases when the core enters fastsleep, code mistakes an idle
thread as running. Because of this, the first thread waking up from
fastsleep which is supposed to resync timebase skips it. So we can
end up having a core with stale timebase value.
This patch fixes the above race by looping on the lock bit even while
entering the idle states.
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Fixes: 7b54e9f213f76 'powernv/powerpc: Add winkle support for offline cpus'
Cc: stable@vger.kernel.org # 3.19+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This means the 'M' flag will work properly when the kernel prints a backtrace.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVkO5XAAoJEOvOhAQsB9HWe4cQAJcsmSXIDN2O6oxvgH8Wilof
EIEMvT13uwBdsjQdYUY6A6B3iUV9wzEEgoosg/JRgpz5/b1FTDMIO4arUPD3Lcak
5bmyVO2qAT+yaLAWSgn6I8DMplXrKiEuK+TkH/mW3p9TdvElLdG3Vg6UI407hSWv
W0QbVwkNtv8XmzshV9F2YdmflT8j1PgYxIu/tEkVOWn37DNW+Fp2OVBrdTIYp3AJ
X6bYZPEcQDCrWWW/s2GmIDrNgryiebasns+CAgGY21262jAYaRcFOJmR47AsTqW7
DSZXIlLc/gJca++hfxqV15RZ4NRHxrebCypTsPtZUV7ZiYHI726eeUZzxsp/9itu
mvhmi+aQUTTUP3dDhiv05f4syAKEb4zslT6SLwcna6oi09M97HfCeQsHqhcFq/MG
KnS2JJoJQToQtJvMUXMQzp5hyHjNlOclIvCxEiL32EZU54PeJOKasy/mptNGEctk
TxACWvoXBQglRaVN+1wIjjr0BaHJSuJa9CUnIfM4WZdSHiMQMx00XLTkZcTnSM6R
12pE54vVolrXswGPJhy4W/Sf1yPSW1tkWSVBbkKLyCIrlAWJtu68rXhvwhG/nz6E
3g6QrDEQGlk6bzUH4CJCEqXLPRN1bNS0XjdkEFh60Lury3Ns5yHKZXPW5vCQ5csr
FQNUyBs595CWbJNfbn1n
=0BDx
-----END PGP SIGNATURE-----
Merge tag 'module_init-device_initcall-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull module_init replacement part one from Paul Gortmaker:
"Replace module_init with equivalent device_initcall in non modules.
This series of commits converts non-modular code that is using the
module_init() call to hook itself into the system to instead use
device_initcall().
The conversion is a runtime no-op, since module_init actually becomes
__initcall in the non-modular case, and that in turn gets mapped onto
device_initcall. A couple files show a larger negative diffstat,
representing ones that had a module_exit function that we remove here
vs previously relying on the linker to dispose of it.
We make this conversion now, so that we can relocate module_init from
init.h into module.h in the future.
The files changed here are just limited to those that would otherwise
have to add module.h to obviously non-modular code, in order to avoid
a compile fail, as testing has shown"
* tag 'module_init-device_initcall-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
MIPS: don't use module_init in non-modular cobalt/mtd.c file
drivers/leds: don't use module_init in non-modular leds-cobalt-raq.c
cris: don't use module_init for non-modular core eeprom.c code
tty/metag_da: Avoid module_init/module_exit in non-modular code
drivers/clk: don't use module_init in clk-nomadik.c which is non-modular
xtensa: don't use module_init for non-modular core network.c code
sh: don't use module_init in non-modular psw.c code
mn10300: don't use module_init in non-modular flash.c code
parisc64: don't use module_init for non-modular core perf code
parisc: don't use module_init for non-modular core pdc_cons code
cris: don't use module_init for non-modular core intmem.c code
ia64: don't use module_init in non-modular sim/simscsi.c code
ia64: don't use module_init for non-modular core kernel/mca.c code
arm: don't use module_init in non-modular mach-vexpress/spc.c code
powerpc: don't use module_init in non-modular 83xx suspend code
powerpc: use device_initcall for registering rtc devices
x86: don't use module_init in non-modular devicetree.c code
x86: don't use module_init in non-modular intel_mid_vrtc.c
A whole lot of bug fixes. Nothing stands out here except the ability to
enable CONFIG_OF on every architecture, and an import of a newer version
of dtc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tm5y
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux
Pull devicetree updates from Grant Likely:
"A whole lot of bug fixes.
Nothing stands out here except the ability to enable CONFIG_OF on
every architecture, and an import of a newer version of dtc"
* tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux: (22 commits)
of/irq: Rename "intc_desc" to "of_intc_desc" to fix OF on sh
of/irq: Fix pSeries boot failure
Documentation: DT: Fix a typo in the filename "lantiq,<chip>-pinumx.txt"
of: define of_find_node_by_phandle for !CONFIG_OF
of/address: use atomic allocation in pci_register_io_range()
of: Add vendor prefix for Zodiac Inflight Innovations
dt/fdt: add empty versions of early_init_dt_*_memory_arch
of: clean-up unnecessary libfdt include paths
of: make unittest select OF_EARLY_FLATTREE instead of depend on it
of: make CONFIG_OF user selectable
MIPS: prepare for user enabling of CONFIG_OF
of/fdt: fix argument name and add comments of unflatten_dt_node()
of: return NUMA_NO_NODE from fallback of_node_to_nid()
tps6507x.txt: Remove executable permission
of/overlay: Grammar s/an negative/a negative/
of/fdt: Make fdt blob input parameters of unflatten functions const
of: add helper function to retrive match data
of: Grammar s/property exist/property exists/
of: Move OF flags to be visible even when !CONFIG_OF
scripts/dtc: Update to upstream version 9d3649bd3be245c9
...
This replaces the plain loop over the sglist array with for_each_sg()
macro which consists of sg_next() function calls. Since powerpc does
select ARCH_HAS_SG_CHAIN, it is necessary to use for_each_sg() in order
to loop over each sg element. This also help find problems with drivers
that do not properly initialize their sg tables when CONFIG_DEBUG_SG is
enabled.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- CPU ops and PSCI (Power State Coordination Interface) refactoring
following the merging of the arm64 ACPI support, together with
handling of Trusted (secure) OS instances
- Using fixmap for permanent FDT mapping, removing the initial dtb
placement requirements (within 512MB from the start of the kernel
image). This required moving the FDT self reservation out of the
memreserve processing
- Idmap (1:1 mapping used for MMU on/off) handling clean-up
- Removing flush_cache_all() - not safe on ARM unless the MMU is off.
Last stages of CPU power down/up are handled by firmware already
- "Alternatives" (run-time code patching) refactoring and support for
immediate branch patching, GICv3 CPU interface access
- User faults handling clean-up
And some fixes:
- Fix for VDSO building with broken ELF toolchains
- Fixing another case of init_mm.pgd usage for user mappings (during
ASID roll-over broadcasting)
- Fix for FPSIMD reloading after CPU hotplug
- Fix for missing syscall trace exit
- Workaround for .inst asm bug
- Compat fix for switching the user tls tpidr_el0 register
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YeGl
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
"Mostly refactoring/clean-up:
- CPU ops and PSCI (Power State Coordination Interface) refactoring
following the merging of the arm64 ACPI support, together with
handling of Trusted (secure) OS instances
- Using fixmap for permanent FDT mapping, removing the initial dtb
placement requirements (within 512MB from the start of the kernel
image). This required moving the FDT self reservation out of the
memreserve processing
- Idmap (1:1 mapping used for MMU on/off) handling clean-up
- Removing flush_cache_all() - not safe on ARM unless the MMU is off.
Last stages of CPU power down/up are handled by firmware already
- "Alternatives" (run-time code patching) refactoring and support for
immediate branch patching, GICv3 CPU interface access
- User faults handling clean-up
And some fixes:
- Fix for VDSO building with broken ELF toolchains
- Fix another case of init_mm.pgd usage for user mappings (during
ASID roll-over broadcasting)
- Fix for FPSIMD reloading after CPU hotplug
- Fix for missing syscall trace exit
- Workaround for .inst asm bug
- Compat fix for switching the user tls tpidr_el0 register"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (42 commits)
arm64: use private ratelimit state along with show_unhandled_signals
arm64: show unhandled SP/PC alignment faults
arm64: vdso: work-around broken ELF toolchains in Makefile
arm64: kernel: rename __cpu_suspend to keep it aligned with arm
arm64: compat: print compat_sp instead of sp
arm64: mm: Fix freeing of the wrong memmap entries with !SPARSEMEM_VMEMMAP
arm64: entry: fix context tracking for el0_sp_pc
arm64: defconfig: enable memtest
arm64: mm: remove reference to tlb.S from comment block
arm64: Do not attempt to use init_mm in reset_context()
arm64: KVM: Switch vgic save/restore to alternative_insn
arm64: alternative: Introduce feature for GICv3 CPU interface
arm64: psci: fix !CONFIG_HOTPLUG_CPU build warning
arm64: fix bug for reloading FPSIMD state after CPU hotplug.
arm64: kernel thread don't need to save fpsimd context.
arm64: fix missing syscall trace exit
arm64: alternative: Work around .inst assembler bugs
arm64: alternative: Merge alternative-asm.h into alternative.h
arm64: alternative: Allow immediate branch as alternative instruction
arm64: Rework alternate sequence for ARM erratum 845719
...
- Disable the 32-bit vdso when building LE, so we can build with a 64-bit only
toolchain.
- EEH fixes from Gavin & Richard.
- Enable the sys_kcmp syscall from Laurent.
- Sysfs control for fastsleep workaround from Shreyas.
- Expose OPAL events as an irq chip by Alistair.
- MSI ops moved to pci_controller_ops by Daniel.
- Fix for kernel to userspace backtraces for perf from Anton.
- Merge pseries and pseries_le defconfigs from Cyril.
- CXL in-kernel API from Mikey.
- OPAL prd driver from Jeremy.
- Fix for DSCR handling & tests from Anshuman.
- Powernv flash mtd driver from Cyril.
- Dynamic DMA Window support on powernv from Alexey.
- LLVM clang fixes & workarounds from Anton.
- Reworked version of the patch to abort syscalls when transactional.
- Fix the swap encoding to support 4TB, from Aneesh.
- Various fixes as usual.
- Freescale updates from Scott: Highlights include more 8xx optimizations, an
e6500 hugetlb optimization, QMan device tree nodes, t1024/t1023 support, and
various fixes and cleanup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=d9Wh
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc updates from Michael Ellerman:
- disable the 32-bit vdso when building LE, so we can build with a
64-bit only toolchain.
- EEH fixes from Gavin & Richard.
- enable the sys_kcmp syscall from Laurent.
- sysfs control for fastsleep workaround from Shreyas.
- expose OPAL events as an irq chip by Alistair.
- MSI ops moved to pci_controller_ops by Daniel.
- fix for kernel to userspace backtraces for perf from Anton.
- merge pseries and pseries_le defconfigs from Cyril.
- CXL in-kernel API from Mikey.
- OPAL prd driver from Jeremy.
- fix for DSCR handling & tests from Anshuman.
- Powernv flash mtd driver from Cyril.
- dynamic DMA Window support on powernv from Alexey.
- LLVM clang fixes & workarounds from Anton.
- reworked version of the patch to abort syscalls when transactional.
- fix the swap encoding to support 4TB, from Aneesh.
- various fixes as usual.
- Freescale updates from Scott: Highlights include more 8xx
optimizations, an e6500 hugetlb optimization, QMan device tree nodes,
t1024/t1023 support, and various fixes and cleanup.
* tag 'powerpc-4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (180 commits)
cxl: Fix typo in debug print
cxl: Add CXL_KERNEL_API config option
powerpc/powernv: Fix wrong IOMMU table in pnv_ioda_setup_bus_dma()
powerpc/mm: Change the swap encoding in pte.
powerpc/mm: PTE_RPN_MAX is not used, remove the same
powerpc/tm: Abort syscalls in active transactions
powerpc/iommu/ioda2: Enable compile with IOV=on and IOMMU_API=off
powerpc/include: Add opal-prd to installed uapi headers
powerpc/powernv: fix construction of opal PRD messages
powerpc/powernv: Increase opal-irqchip initcall priority
powerpc: Make doorbell check preemption safe
powerpc/powernv: pnv_init_idle_states() should only run on powernv
macintosh/nvram: Remove as unused
powerpc: Don't use gcc specific options on clang
powerpc: Don't use -mno-strict-align on clang
powerpc: Only use -mtraceback=no, -mno-string and -msoft-float if toolchain supports it
powerpc: Only use -mabi=altivec if toolchain supports it
powerpc: Fix duplicate const clang warning in user access code
vfio: powerpc/spapr: Support Dynamic DMA windows
vfio: powerpc/spapr: Register memory and define IOMMU v2
...
Pull crypto update from Herbert Xu:
"Here is the crypto update for 4.2:
API:
- Convert RNG interface to new style.
- New AEAD interface with one SG list for AD and plain/cipher text.
All external AEAD users have been converted.
- New asymmetric key interface (akcipher).
Algorithms:
- Chacha20, Poly1305 and RFC7539 support.
- New RSA implementation.
- Jitter RNG.
- DRBG is now seeded with both /dev/random and Jitter RNG. If kernel
pool isn't ready then DRBG will be reseeded when it is.
- DRBG is now the default crypto API RNG, replacing krng.
- 842 compression (previously part of powerpc nx driver).
Drivers:
- Accelerated SHA-512 for arm64.
- New Marvell CESA driver that supports DMA and more algorithms.
- Updated powerpc nx 842 support.
- Added support for SEC1 hardware to talitos"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (292 commits)
crypto: marvell/cesa - remove COMPILE_TEST dependency
crypto: algif_aead - Temporarily disable all AEAD algorithms
crypto: af_alg - Forbid the use internal algorithms
crypto: echainiv - Only hold RNG during initialisation
crypto: seqiv - Add compatibility support without RNG
crypto: eseqiv - Offer normal cipher functionality without RNG
crypto: chainiv - Offer normal cipher functionality without RNG
crypto: user - Add CRYPTO_MSG_DELRNG
crypto: user - Move cryptouser.h to uapi
crypto: rng - Do not free default RNG when it becomes unused
crypto: skcipher - Allow givencrypt to be NULL
crypto: sahara - propagate the error on clk_disable_unprepare() failure
crypto: rsa - fix invalid select for AKCIPHER
crypto: picoxcell - Update to the current clk API
crypto: nx - Check for bogus firmware properties
crypto: marvell/cesa - add DT bindings documentation
crypto: marvell/cesa - add support for Kirkwood and Dove SoCs
crypto: marvell/cesa - add support for Orion SoCs
crypto: marvell/cesa - add allhwsupport module parameter
crypto: marvell/cesa - add support for all armada SoCs
...
Merge the mvebu/drivers branch of the arm-soc tree which contains
just a single patch bfa1ce5f38 ("bus:
mvebu-mbus: add mv_mbus_dram_info_nooverlap()") that happens to be
a prerequisite of the new marvell/cesa crypto driver.
Freescale updates from Scott:
"Highlights include more 8xx optimizations, an e6500 hugetlb optimization,
QMan device tree nodes, t1024/t1023 support, and various fixes and
cleanup."
This patch changes the syscall handler to doom (tabort) active
transactions when a syscall is made and return very early without
performing the syscall and keeping side effects to a minimum (no CPU
accounting or system call tracing is performed). Also included is a
new HWCAP2 bit, PPC_FEATURE2_HTM_NOSC, to indicate this
behaviour to userspace.
Currently, the system call instruction automatically suspends an
active transaction which causes side effects to persist when an active
transaction fails.
This does change the kernel's behaviour, but in a way that was
documented as unsupported. It doesn't reduce functionality as
syscalls will still be performed after tsuspend; it just requires that
the transaction be explicitly suspended. It also provides a
consistent interface and makes the behaviour of user code
substantially the same across powerpc and platforms that do not
support suspended transactions (e.g. x86 and s390).
Performance measurements using
http://ozlabs.org/~anton/junkcode/null_syscall.c indicate the cost of
a normal (non-aborted) system call increases by about 0.25%.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently these two RTC devices are in core platform code
where it is not possible for them to be modular. It will
never be modular, so using module_init as an alias for
__initcall can be somewhat misleading.
Fix this up now, so that we can relocate module_init from
init.h into module.h in the future. If we don't do this, we'd
have to add module.h to obviously non-modular code, and that
would be a worse thing.
Note that direct use of __initcall is discouraged, vs. one
of the priority categorized subgroups. As __initcall gets
mapped onto device_initcall, our use of device_initcall
directly in this change means that the runtime impact is
zero -- they will remain at level 6 in initcall ordering.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Geoff Levand <geoff@infradead.org>
Acked-by: Geoff Levand <geoff@infradead.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
We are adding support for DMA memory pre-registration to be used in
conjunction with VFIO. The idea is that the userspace which is going to
run a guest may want to pre-register a user space memory region so
it all gets pinned once and never goes away. Having this done,
a hypervisor will not have to pin/unpin pages on every DMA map/unmap
request. This is going to help with multiple pinning of the same memory.
Another use of it is in-kernel real mode (mmu off) acceleration of
DMA requests where real time translation of guest physical to host
physical addresses is non-trivial and may fail as linux ptes may be
temporarily invalid. Also, having cached host physical addresses
(compared to just pinning at the start and then walking the page table
again on every H_PUT_TCE), we can be sure that the addresses which we put
into TCE table are the ones we already pinned.
This adds a list of memory regions to mm_context_t. Each region consists
of a header and a list of physical addresses. This adds API to:
1. register/unregister memory regions;
2. do final cleanup (which puts all pre-registered pages);
3. do userspace to physical address translation;
4. manage usage counters; multiple registration of the same memory
is allowed (once per container).
This implements 2 counters per registered memory region:
- @mapped: incremented on every DMA mapping; decremented on unmapping;
initialized to 1 when a region is just registered; once it becomes zero,
no more mappings allowe;
- @used: incremented on every "register" ioctl; decremented on
"unregister"; unregistration is allowed for DMA mapped regions unless
it is the very last reference. For the very last reference this checks
that the region is still mapped and returns -EBUSY so the userspace
gets to know that memory is still pinned and unregistration needs to
be retried; @used remains 1.
Host physical addresses are stored in vmalloc'ed array. In order to
access these in the real mode (mmu off), there is a real_vmalloc_addr()
helper. In-kernel acceleration patchset will move it from KVM to MMU code.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
At the moment writing new TCE value to the IOMMU table fails with EBUSY
if there is a valid entry already. However PAPR specification allows
the guest to write new TCE value without clearing it first.
Another problem this patch is addressing is the use of pool locks for
external IOMMU users such as VFIO. The pool locks are to protect
DMA page allocator rather than entries and since the host kernel does
not control what pages are in use, there is no point in pool locks and
exchange()+put_page(oldtce) is sufficient to avoid possible races.
This adds an exchange() callback to iommu_table_ops which does the same
thing as set() plus it returns replaced TCE and DMA direction so
the caller can release the pages afterwards. The exchange() receives
a physical address unlike set() which receives linear mapping address;
and returns a physical address as the clear() does.
This implements exchange() for P5IOC2/IODA/IODA2. This adds a requirement
for a platform to have exchange() implemented in order to support VFIO.
This replaces iommu_tce_build() and iommu_clear_tce() with
a single iommu_tce_xchg().
This makes sure that TCE permission bits are not set in TCE passed to
IOMMU API as those are to be calculated by platform code from
DMA direction.
This moves SetPageDirty() to the IOMMU code to make it work for both
VFIO ioctl interface in in-kernel TCE acceleration (when it becomes
available later).
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[aw: for the vfio related changes]
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds missing locks in iommu_take_ownership()/
iommu_release_ownership().
This marks all pages busy in iommu_table::it_map in order to catch
errors if there is an attempt to use this table while ownership over it
is taken.
This only clears TCE content if there is no page marked busy in it_map.
Clearing must be done outside of the table locks as iommu_clear_tce()
called from iommu_clear_tces_and_put_pages() does this.
In order to use bitmap_empty(), the existing code clears bit#0 which
is set even in an empty table if it is bus-mapped at 0 as
iommu_init_table() reserves page#0 to prevent buggy drivers
from crashing when allocated page is bus-mapped at zero
(which is correct). This restores the bit in the case of failure
to bring the it_map to the state it was in when we called
iommu_take_ownership().
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds tce_iommu_take_ownership() and tce_iommu_release_ownership
which call in a loop iommu_take_ownership()/iommu_release_ownership()
for every table on the group. As there is just one now, no change in
behaviour is expected.
At the moment the iommu_table struct has a set_bypass() which enables/
disables DMA bypass on IODA2 PHB. This is exposed to POWERPC IOMMU code
which calls this callback when external IOMMU users such as VFIO are
about to get over a PHB.
The set_bypass() callback is not really an iommu_table function but
IOMMU/PE function. This introduces a iommu_table_group_ops struct and
adds take_ownership()/release_ownership() callbacks to it which are
called when an external user takes/releases control over the IOMMU.
This replaces set_bypass() with ownership callbacks as it is not
necessarily just bypass enabling, it can be something else/more
so let's give it more generic name.
The callbacks is implemented for IODA2 only. Other platforms (P5IOC2,
IODA1) will use the old iommu_take_ownership/iommu_release_ownership API.
The following patches will replace iommu_take_ownership/
iommu_release_ownership calls in IODA2 with full IOMMU table release/
create.
As we here and touching bypass control, this removes
pnv_pci_ioda2_setup_bypass_pe() as it does not do much
more compared to pnv_pci_ioda2_set_bypass. This moves tce_bypass_base
initialization to pnv_pci_ioda2_setup_dma_pe.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[aw: for the vfio related changes]
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
So far one TCE table could only be used by one IOMMU group. However
IODA2 hardware allows programming the same TCE table address to
multiple PE allowing sharing tables.
This replaces a single pointer to a group in a iommu_table struct
with a linked list of groups which provides the way of invalidating
TCE cache for every PE when an actual TCE table is updated. This adds
pnv_pci_link_table_and_group() and pnv_pci_unlink_table_and_group()
helpers to manage the list. However without VFIO, it is still going
to be a single IOMMU group per iommu_table.
This changes iommu_add_device() to add a device to a first group
from the group list of a table as it is only called from the platform
init code or PCI bus notifier and at these moments there is only
one group per table.
This does not change TCE invalidation code to loop through all
attached groups in order to simplify this patch and because
it is not really needed in most cases. IODA2 is fixed in a later
patch.
This should cause no behavioural change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[aw: for the vfio related changes]
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Modern IBM POWERPC systems support multiple (currently two) TCE tables
per IOMMU group (a.k.a. PE). This adds a iommu_table_group container
for TCE tables. Right now just one table is supported.
This defines iommu_table_group struct which stores pointers to
iommu_group and iommu_table(s). This replaces iommu_table with
iommu_table_group where iommu_table was used to identify a group:
- iommu_register_group();
- iommudata of generic iommu_group;
This removes @data from iommu_table as it_table_group provides
same access to pnv_ioda_pe.
For IODA, instead of embedding iommu_table, the new iommu_table_group
keeps pointers to those. The iommu_table structs are allocated
dynamically.
For P5IOC2, both iommu_table_group and iommu_table are embedded into
PE struct. As there is no EEH and SRIOV support for P5IOC2,
iommu_free_table() should not be called on iommu_table struct pointers
so we can keep it embedded in pnv_phb::p5ioc2.
For pSeries, this replaces multiple calls of kzalloc_node() with a new
iommu_pseries_alloc_group() helper and stores the table group struct
pointer into the pci_dn struct. For release, a iommu_table_free_group()
helper is added.
This moves iommu_table struct allocation from SR-IOV code to
the generic DMA initialization code in pnv_pci_ioda_setup_dma_pe and
pnv_pci_ioda2_setup_dma_pe as this is where DMA is actually initialized.
This change is here because those lines had to be changed anyway.
This should cause no behavioural change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[aw: for the vfio related changes]
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds a iommu_table_ops struct and puts pointer to it into
the iommu_table struct. This moves tce_build/tce_free/tce_get/tce_flush
callbacks from ppc_md to the new struct where they really belong to.
This adds the requirement for @it_ops to be initialized before calling
iommu_init_table() to make sure that we do not leave any IOMMU table
with iommu_table_ops uninitialized. This is not a parameter of
iommu_init_table() though as there will be cases when iommu_init_table()
will not be called on TCE tables, for example - VFIO.
This does s/tce_build/set/, s/tce_free/clear/ and removes "tce_"
redundant prefixes.
This removes tce_xxx_rm handlers from ppc_md but does not add
them to iommu_table_ops as this will be done later if we decide to
support TCE hypercalls in real mode. This removes _vm callbacks as
only virtual mode is supported by now so this also removes @rm parameter.
For pSeries, this always uses tce_buildmulti_pSeriesLP/
tce_buildmulti_pSeriesLP. This changes multi callback to fall back to
tce_build_pSeriesLP/tce_free_pSeriesLP if FW_FEATURE_MULTITCE is not
present. The reason for this is we still have to support "multitce=off"
boot parameter in disable_multitce() and we do not want to walk through
all IOMMU tables in the system and replace "multi" callbacks with single
ones.
For powernv, this defines _ops per PHB type which are P5IOC2/IODA1/IODA2.
This makes the callbacks for them public. Later patches will extend
callbacks for IODA1/2.
No change in behaviour is expected.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Normally a bitmap from the iommu_table is used to track what TCE entry
is in use. Since we are going to use iommu_table without its locks and
do xchg() instead, it becomes essential not to put bits which are not
implied in the direction flag as the old TCE value (more precisely -
the permission bits) will be used to decide whether to put the page or not.
This adds iommu_direction_to_tce_perm() (its counterpart is there already)
and uses it for powernv's pnv_tce_build().
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This moves page pinning (get_user_pages_fast()/put_page()) code out of
the platform IOMMU code and puts it to VFIO IOMMU driver where it belongs
to as the platform code does not deal with page pinning.
This makes iommu_take_ownership()/iommu_release_ownership() deal with
the IOMMU table bitmap only.
This removes page unpinning from iommu_take_ownership() as the actual
TCE table might contain garbage and doing put_page() on it is undefined
behaviour.
Besides the last part, the rest of the patch is mechanical.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[aw: for the vfio related changes]
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
At the moment iommu_free_table() only releases memory if
the table was initialized for the platform code use, i.e. it had
it_map initialized (which purpose is to track DMA memory space use).
With dynamic DMA windows, we will need to be able to release
iommu_table even if it was used for VFIO in which case it_map is NULL
so does the patch.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
So far an iommu_table lifetime was the same as PE. Dynamic DMA windows
will change this and iommu_free_table() will not always require
the group to be released.
This moves iommu_group_put() out of iommu_free_table().
This adds a iommu_pseries_free_table() helper which does
iommu_group_put() and iommu_free_table(). Later it will be
changed to receive a table_group and we will have to change less
lines then.
This should cause no behavioural change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This relies on the fact that a PCI device always has an IOMMU table
which may not be the case when we get dynamic DMA windows so
let's use more reliable check for IOMMU group here.
As we do not rely on the table presence here, remove the workaround
from pnv_pci_ioda2_set_bypass(); also remove the @add_to_iommu_group
parameter from pnv_ioda_setup_bus_dma().
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In include/linux/pci.h, we already #include <asm/pci.h>, so we don't need
to include <asm/pci.h> directly.
Remove the unnecessary includes. All the files here already include
<linux/pci.h>.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au> # sh
Acked-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds some in-code documentation to the DSCR related code to
make it more readable without having any functional change to it.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PACA_DSCR offset macro tracks dscr_default element in the paca
structure. Better change the name of this macro to match that of the
data element it tracks. Makes the code more readable.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The process context switch code no longer uses dscr_default variable
from the sysfs.c file. The variable became unused when we started
storing the CPU specific DSCR value in the PACA structure instead.
This patch just removes this extern declaration. It was originally
added by the following commit.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently DSCR (Data Stream Control Register) can be accessed with
mfspr or mtspr instructions inside a thread via two different SPR
numbers. One being the user accessible problem state SPR number 0x03
and the other being the privilege state SPR number 0x11. All access
through the privilege state SPR number get emulated through illegal
instruction exception. Any access through the problem state SPR number
raises one facility unavailable exception which sets the thread based
dscr_inherit bit and enables DSCR facility through FSCR register thus
allowing direct access to DSCR without going through this exception in
the future. We set the thread.dscr_inherit bit whether the access was
with mfspr or mtspr instruction which is neither correct nor does it
match the behaviour through the instruction emulation code path driven
from privilege state SPR number. User currently observes two different
kind of behaviour when accessing the DSCR through these two SPR numbers.
This problem can be observed through these two test cases by replacing
the privilege state SPR number with the problem state SPR number.
(1) http://ozlabs.org/~anton/junkcode/dscr_default_test.c
(2) http://ozlabs.org/~anton/junkcode/dscr_explicit_test.c
This patch fixes the problem by making sure that the behaviour visible
to the user remains the same irrespective of which SPR number is being
used. Inside facility unavailable exception, we check whether it was
cuased by a mfspr or a mtspr isntrucction. In case of mfspr instruction,
just emulate the instruction. In case of mtspr instruction, set the
thread based dscr_inherit bit and also enable the facility through FSCR.
All user SPR based mfspr instruction will be emulated till one user SPR
based mtspr has been executed.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 28158cd "powerpc/eeh: Enhance pcibios_set_pcie_reset_state()"
introduced a fix for a problem where certain configurations could lead to
pci_reset_function() destroying the state of PCI devices other than the one
specified.
Unfortunately, the fix has a trivial bug - it calls pci_save_state() again,
when it should be calling pci_restore_state(). This corrects the problem.
Cc: Gavin Shan <gwshan@au1.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With the libfdt include fixups to use "" instead of <> in the
latest dtc import in commit 4760597 (scripts/dtc: Update to upstream
version 9d3649bd3be245c9), it is no longer necessary to add explicit
include paths to use libfdt. Remove these across the kernel.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Grant Likely <grant.likely@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: linuxppc-dev@lists.ozlabs.org
This adds a hook into the powerpc pci code for pci_disable_device() calls. The
generic code already provides a weak pcibios_disable_device() symbol, so we
just need to provide our own in powerpc and it'll get picked up.
This is passed directly to the phb controller ops, provided one exists.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add release_device() hook to phb ops so we can clean up for specific phbs.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Export pcibios_claim_one_bus, pcibios_scan_phb and pcibios_alloc_controller.
These will be used by the CXL driver.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch implements PAGE_EXEC capability on the 8xx.
All pages PP exec bits are set to 000, which means Execute for
Supervisor and no Execute for User.
Then we use the APG to say whether accesses are according to Page
rules, "all Supervisor" rules (Exec for all) and
"all User" rules (Exec for noone)
Therefore, we define 4 APG groups. msb is _PAGE_EXEC,
lsb is _PAGE_USER. MI_AP is initialised as follows:
GP0 (00) => Not User, no exec => 11 (all accesses performed as user)
GP1 (01) => User but no exec => 11 (all accesses performed as user)
GP2 (10) => Not User, exec => 01 (rights according to page definition)
GP3 (11) => User, exec => 00 (all accesses performed as supervisor)
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[scottwood: comments: s/exec/data/ on data side, and s/pages/pages'/]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Use of APG for handling PAGE_USER.
All pages PP exec bits are set to either 000 or 011, which means
respectively RW for Supervisor and no access for User, or RO for
Supervisor and no access for user.
Then we use the APG to say whether accesses are according to
Page rules or "all Supervisor" rules (Access to all)
Therefore, we define 2 APG groups corresponding to _PAGE_USER.
Mx_AP are initialised as follows:
GP0 => No user => 01 (all accesses performed according
to page definition)
GP1 => User => 00 (all accesses performed as supervisor
according to page definition)
This removes the special 8xx handling in pte_update()
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
By default, TASK_SIZE is set to 0x80000000 for PPC_8xx, which is most
likely sufficient for most cases. However, kernel configuration allows
to set TASK_SIZE to another value, so the 8xx shall handle it.
This patch also takes into account the case of PAGE_OFFSET lower than
0x80000000, allthought most of the time it is equal to 0xC0000000
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
We now have SPRG2 available as in it not used anymore for saving CR, so we don't
need to crash DAR anymore for saving r3 for CPU6 ERRATA handling.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
CR only needs to be preserved when checking if we are handling a kernel address.
So we can preserve CR in a register:
- In ITLBMiss, check is done only when CONFIG_MODULES is defined. Otherwise we
don't need to do anything at all with CR.
- We use r10, then we reload SRR0/MD_EPN into r10 when CR is restored
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
In order to be able to reduce scope during which CR is saved, we take
CR saving/restoring out of exception PROLOG and EPILOG
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Having a macro will help keep clear code.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This code can never be executed as it is only built when
CONFIG_PPC_E500MC is unset, but the only CPUs that have CPU_FTR_L2CSR
require CONFIG_PPC_E500MC and do not have the MSR/HID0-based nap
mechanism that this file uses.
Signed-off-by: Scott Wood <scottwood@freescale.com>
This splits off the reservation of the memory occupied by the FDT
binary itself from the processing of the memory reservations it
contains. This is necessary because the physical address of the FDT,
which is needed to perform the reservation, may not be known to the
FDT driver core, i.e., it may be mapped outside the linear direct
mapping, in which case __pa() returns a bogus value.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We need to use a trampoline when using LOAD_HANDLER(), because the
destination needs to be in the first 64kB. An absolute branch has
no such limitations, so just jump there.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We had some code to restore the LR in the relocatable system call path
back when we used the LR to do an indirect branch.
Commit 6a404806df ("powerpc: Avoid link stack corruption in MMU
on syscall entry path") changed this to use the CTR which is volatile
across system calls so does not need restoring.
Remove the stale comment and the restore of the LR.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Some systems only need to deal with DMA masks for PCI devices.
For these systems, we can avoid the need for a platform hook and
instead use a pci controller based hook.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Remove unneeded ppc_md functions. Patch callsites to use pci_controller_ops
functions exclusively.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add MSI setup and teardown functions to pci_controller_ops.
Patch the callsites (arch_{setup,teardown}_msi_irqs) to prefer the
controller ops version if it's available.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Recent toolchains force the TOC to be 256 byte aligned. We need
to enforce this alignment in our linker script, otherwise pointers
to our TOC variables (__toc_start, __prom_init_toc_start) could
be incorrect.
If they are bad, we die a few hundred instructions into boot.
Cc: stable@vger.kernel.org
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently, the macro IS_BRIDGE is not used any where.
This patch just removes it.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
To retrieve the PCI slot state, EEH driver would set a timeout for that.
While current comment is not aligned to what the code does.
This patch fixes those comments according to the code.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
struct pci_io_addr_range{} stores the information of pci resources. It
would be better to keep these related fields have the same type as in
struct resource{}.
This patch fixes the start/end/flags type in struct pci_io_addr_range{} to
have the same type as in struct resource{}.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The patch defines PCI error types and functions in uapi/asm/eeh.h
and exports function eeh_pe_inject_err(), which will be called by
VFIO driver to inject the specified PCI error to the indicated
PE for testing purpose.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Before 69111bac42 ("powerpc: Replace __get_cpu_var uses"), in
save_mce_event, index got the value of mce_nest_count, and
mce_nest_count was incremented *after* index was set.
However, that patch changed the behaviour so that mce_nest count was
incremented *before* setting index.
This causes an off-by-one error, as get_mce_event sets index as
mce_nest_count - 1 before reading mce_event. Thus get_mce_event reads
bogus data, causing warnings like
"Machine Check Exception, Unknown event version 0 !"
and breaking MCEs handling.
Restore the old behaviour and unbreak MCE handling by subtracting one
from the newly incremented value.
The same broken change occured in machine_check_queue_event (which set
a queue read by machine_check_process_queued_event). Fix that too,
unbreaking printing of MCE information.
Fixes: 69111bac42 ("powerpc: Replace __get_cpu_var uses")
CC: stable@vger.kernel.org
CC: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
CC: Christoph Lameter <cl@linux.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The only little endian configuration we support is ppc64le. As such if
we're building little endian we don't need a 32-bit VDSO, because there
is no 32-bit userspace.
This patch is a fairly ugly mess of #ifdefs, but is the minimal logic
required to disable the 32-bit VDSO. We can hopefully clean up the
result in future with some further refactoring.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In vdso_fixup_features() we have start64/start32 and size64/size32, but
they have the same types, ie. void * and unsigned long.
They're only used to save the return value from find_sectionXX() for the
subsequent call to do_feature_fixups(), so there's no overlap in their
usage either.
So we can just consolidate them into start/size and avoid the
duplication.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently we print "Starting Linux PPC64" at boot. But we don't mention
anywhere whether the kernel is big or little endian.
If we print the utsname->machine value instead we get either "ppc64" or
"ppc64le" which is much more informative, eg:
Starting Linux ppc64le #1 SMP Wed Apr 15 12:12:20 AEST 2015
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Export the of_get_ibm_chip_id() function. This will be used by the
PowerNV NX-842 driver.
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Patches 7cba160ad "powernv/cpuidle: Redesign idle states management"
and 77b54e9f2 "powernv/powerpc: Add winkle support for offline cpus"
use non-volatile condition registers (cr2, cr3 and cr4) early in the system
reset interrupt handler (system_reset_pSeries()) before it has been determined
if state loss has occurred. If state loss has not occurred, control returns via
the power7_wakeup_noloss() path which does not restore those condition
registers, leaving them corrupted.
Fix this by restoring the condition registers in the power7_wakeup_noloss()
case.
This is apparent when running a KVM guest on hardware that does not
support winkle or sleep and the guest makes use of secondary threads. In
practice this means Power7 machines, though some early unreleased Power8
machines may also be susceptible.
The secondary CPUs are taken off line before the guest is started and
they call pnv_smp_cpu_kill_self(). This checks support for sleep
states (in this case there is no support) and power7_nap() is called.
When the CPU is woken, power7_nap() returns and because the CPU is
still off line, the main while loop executes again. The sleep states
support test is executed again, but because the tested values cannot
have changed, the compiler has optimized the test away and instead we
rely on the result of the first test, which has been left in cr3
and/or cr4. With the result overwritten, the wrong branch is taken and
power7_winkle() is called on a CPU that does not support it, leading
to it stalling.
Fixes: 7cba160ad7 ("powernv/cpuidle: Redesign idle states management")
Fixes: 77b54e9f21 ("powernv/powerpc: Add winkle support for offline cpus")
[mpe: Massage change log a bit more]
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 1c509148b ("powerpc/eeh: Do probe on pci_dn") probes EEH
devices in early stage, which is reasonable to pSeries platform.
However, it's wrong for PowerNV platform because the PE# isn't
determined until the resources (IO and MMIO) are assigned to
PE in hotplug case. So we have to delay probing EEH devices
for PowerNV platform until the PE# is assigned.
Fixes: ff57b454dd ("powerpc/eeh: Do probe on pci_dn")
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When asserting reset in pcibios_set_pcie_reset_state(), the PE
is enforced to (hardware) frozen state in order to drop unexpected
PCI transactions (except PCI config read/write) automatically by
hardware during reset, which would cause recursive EEH error.
However, the (software) frozen state EEH_PE_ISOLATED is missed.
When users get 0xFF from PCI config or MMIO read, EEH_PE_ISOLATED
is set in PE state retrival backend. Unfortunately, nobody (the
reset handler or the EEH recovery functinality in host) will clear
EEH_PE_ISOLATED when the PE has been passed through to guest.
The patch sets and clears EEH_PE_ISOLATED properly during reset
in function pcibios_set_pcie_reset_state() to fix the issue.
Fixes: 28158cd ("Enhance pcibios_set_pcie_reset_state()")
Reported-by: Carol L. Soto <clsoto@us.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Tested-by: Carol L. Soto <clsoto@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This reverts commit feba40362b.
Although the principle of this change is good, the implementation has a
few issues.
Firstly we can sometimes fail to abort a syscall because r12 may have
been clobbered by C code if we went down the virtual CPU accounting
path, or if syscall tracing was enabled.
Secondly we have decided that it is safer to abort the syscall even
earlier in the syscall entry path, so that we avoid the syscall tracing
path when we are transactional.
So that we have time to thoroughly test those changes we have decided to
revert this for this merge window and will merge the fixed version in
the next window.
NB. Rather than reverting the selftest we just drop tm-syscall from
TEST_PROGS so that it's not run by default.
Fixes: feba40362b ("powerpc/tm: Abort syscalls in active transactions")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- Fix for mm_dec_nr_pmds() from Scott.
- Fixes for oopses seen with KVM + THP from Aneesh.
- Build fixes from Aneesh & Shreyas.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6yQx
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc fixes from Michael Ellerman:
- fix for mm_dec_nr_pmds() from Scott.
- fixes for oopses seen with KVM + THP from Aneesh.
- build fixes from Aneesh & Shreyas.
* tag 'powerpc-4.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
powerpc/mm: Fix build error with CONFIG_PPC_TRANSACTIONAL_MEM disabled
powerpc/kvm: Fix ppc64_defconfig + PPC_POWERNV=n build error
powerpc/mm/thp: Return pte address if we find trans_splitting.
powerpc/mm/thp: Make page table walk safe against thp split/collapse
KVM: PPC: Remove page table walk helpers
KVM: PPC: Use READ_ONCE when dereferencing pte_t pointer
powerpc/hugetlb: Call mm_dec_nr_pmds() in hugetlb_free_pmd_range()
Book3S HV only (debugging aids, minor performance improvements and some
cleanups). But there are also bug fixes and small cleanups for ARM,
x86 and s390.
The task_migration_notifier revert and real fix is still pending review,
but I'll send it as soon as possible after -rc1.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJVOONLAAoJEL/70l94x66DbsMIAIpZPsaqgXOC1sDEiZuYay+6
rD4n4id7j8hIAzcf3AlZdyf5XgLlr6I1Zyt62s1WcoRq/CCnL7k9EljzSmw31WFX
P2y7/J0iBdkn0et+PpoNThfL2GsgTqNRCLOOQlKgEQwMP9Dlw5fnUbtC1UchOzTg
eAMeBIpYwufkWkXhdMw4PAD4lJ9WxUZ1eXHEBRzJb0o0ZxAATJ1tPZGrFJzoUOSM
WsVNTuBsNd7upT02kQdvA1TUo/OPjseTOEoksHHwfcORt6bc5qvpctL3jYfcr7sk
/L6sIhYGVNkjkuredjlKGLfT2DDJjSEdJb1k2pWrDRsY76dmottQubAE9J9cDTk=
=OAi2
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull second batch of KVM changes from Paolo Bonzini:
"This mostly includes the PPC changes for 4.1, which this time cover
Book3S HV only (debugging aids, minor performance improvements and
some cleanups). But there are also bug fixes and small cleanups for
ARM, x86 and s390.
The task_migration_notifier revert and real fix is still pending
review, but I'll send it as soon as possible after -rc1"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (29 commits)
KVM: arm/arm64: check IRQ number on userland injection
KVM: arm: irqfd: fix value returned by kvm_irq_map_gsi
KVM: VMX: Preserve host CR4.MCE value while in guest mode.
KVM: PPC: Book3S HV: Use msgsnd for signalling threads on POWER8
KVM: PPC: Book3S HV: Translate kvmhv_commence_exit to C
KVM: PPC: Book3S HV: Streamline guest entry and exit
KVM: PPC: Book3S HV: Use bitmap of active threads rather than count
KVM: PPC: Book3S HV: Use decrementer to wake napping threads
KVM: PPC: Book3S HV: Don't wake thread with no vcpu on guest IPI
KVM: PPC: Book3S HV: Get rid of vcore nap_count and n_woken
KVM: PPC: Book3S HV: Move vcore preemption point up into kvmppc_run_vcpu
KVM: PPC: Book3S HV: Minor cleanups
KVM: PPC: Book3S HV: Simplify handling of VCPUs that need a VPA update
KVM: PPC: Book3S HV: Accumulate timing information for real-mode code
KVM: PPC: Book3S HV: Create debugfs file for each guest's HPT
KVM: PPC: Book3S HV: Add ICP real mode counters
KVM: PPC: Book3S HV: Move virtual mode ICP functions to real-mode
KVM: PPC: Book3S HV: Convert ICS mutex lock to spin lock
KVM: PPC: Book3S HV: Add guest->host real mode completion counters
KVM: PPC: Book3S HV: Add helpers for lock/unlock hpte
...
This uses msgsnd where possible for signalling other threads within
the same core on POWER8 systems, rather than IPIs through the XICS
interrupt controller. This includes waking secondary threads to run
the guest, the interrupts generated by the virtual XICS, and the
interrupts to bring the other threads out of the guest when exiting.
Aggregated statistics from debugfs across vcpus for a guest with 32
vcpus, 8 threads/vcore, running on a POWER8, show this before the
change:
rm_entry: 3387.6ns (228 - 86600, 1008969 samples)
rm_exit: 4561.5ns (12 - 3477452, 1009402 samples)
rm_intr: 1660.0ns (12 - 553050, 3600051 samples)
and this after the change:
rm_entry: 3060.1ns (212 - 65138, 953873 samples)
rm_exit: 4244.1ns (12 - 9693408, 954331 samples)
rm_intr: 1342.3ns (12 - 1104718, 3405326 samples)
for a test of booting Fedora 20 big-endian to the login prompt.
The time taken for a H_PROD hcall (which is handled in the host
kernel) went down from about 35 microseconds to about 16 microseconds
with this change.
The noinline added to kvmppc_run_core turned out to be necessary for
good performance, at least with gcc 4.9.2 as packaged with Fedora 21
and a little-endian POWER8 host.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently, the entry_exit_count field in the kvmppc_vcore struct
contains two 8-bit counts, one of the threads that have started entering
the guest, and one of the threads that have started exiting the guest.
This changes it to an entry_exit_map field which contains two bitmaps
of 8 bits each. The advantage of doing this is that it gives us a
bitmap of which threads need to be signalled when exiting the guest.
That means that we no longer need to use the trick of setting the
HDEC to 0 to pull the other threads out of the guest, which led in
some cases to a spurious HDEC interrupt on the next guest entry.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
We can tell when a secondary thread has finished running a guest by
the fact that it clears its kvm_hstate.kvm_vcpu pointer, so there
is no real need for the nap_count field in the kvmppc_vcore struct.
This changes kvmppc_wait_for_nap to poll the kvm_hstate.kvm_vcpu
pointers of the secondary threads rather than polling vc->nap_count.
Besides reducing the size of the kvmppc_vcore struct by 8 bytes,
this also means that we can tell which secondary threads have got
stuck and thus print a more informative error message.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
* Remove unused kvmppc_vcore::n_busy field.
* Remove setting of RMOR, since it was only used on PPC970 and the
PPC970 KVM support has been removed.
* Don't use r1 or r2 in setting the runlatch since they are
conventionally reserved for other things; use r0 instead.
* Streamline the code a little and remove the ext_interrupt_to_host
label.
* Add some comments about register usage.
* hcall_try_real_mode doesn't need to be global, and can't be
called from C code anyway.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This reads the timebase at various points in the real-mode guest
entry/exit code and uses that to accumulate total, minimum and
maximum time spent in those parts of the code. Currently these
times are accumulated per vcpu in 5 parts of the code:
* rm_entry - time taken from the start of kvmppc_hv_entry() until
just before entering the guest.
* rm_intr - time from when we take a hypervisor interrupt in the
guest until we either re-enter the guest or decide to exit to the
host. This includes time spent handling hcalls in real mode.
* rm_exit - time from when we decide to exit the guest until the
return from kvmppc_hv_entry().
* guest - time spend in the guest
* cede - time spent napping in real mode due to an H_CEDE hcall
while other threads in the same vcore are active.
These times are exposed in debugfs in a directory per vcpu that
contains a file called "timings". This file contains one line for
each of the 5 timings above, with the name followed by a colon and
4 numbers, which are the count (number of times the code has been
executed), the total time, the minimum time, and the maximum time,
all in nanoseconds.
The overhead of the extra code amounts to about 30ns for an hcall that
is handled in real mode (e.g. H_SET_DABR), which is about 25%. Since
production environments may not wish to incur this overhead, the new
code is conditional on a new config symbol,
CONFIG_KVM_BOOK3S_HV_EXIT_TIMING.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
We can disable a THP split or a hugepage collapse by disabling irq.
We do send IPI to all the cpus in the early part of split/collapse,
and disabling local irq ensure we don't make progress with
split/collapse. If the THP is getting split we return NULL from
find_linux_pte_or_hugepte(). For all the current callers it should be ok.
We need to be careful if we want to use returned pte_t pointer outside
the irq disabled region. W.r.t to THP split, the pfn remains the same,
but then a hugepage collapse will result in a pfn change. There are
few steps we can take to avoid a hugepage collapse.One way is to take page
reference inside the irq disable region. Other option is to take
mmap_sem so that a parallel collapse will not happen. We can also
disable collapse by taking pmd_lock. Another method used by kvm
subsystem is to check whether we had a mmu_notifer update in between
using mmu_notifier_retry().
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- Numerous minor fixes, cleanups etc.
- More EEH work from Gavin to remove its dependency on device_nodes.
- Memory hotplug implemented entirely in the kernel from Nathan Fontenot.
- Removal of redundant CONFIG_PPC_OF by Kevin Hao.
- Rewrite of VPHN parsing logic & tests from Greg Kurz.
- A fix from Nish Aravamudan to reduce memory usage by clamping
nodes_possible_map.
- Support for pstore on powernv from Hari Bathini.
- Removal of old powerpc specific byte swap routines by David Gibson.
- Fix from Vasant Hegde to prevent the flash driver telling you it was flashing
your firmware when it wasn't.
- Patch from Ben Herrenschmidt to add an OPAL heartbeat driver.
- Fix for an oops causing get/put_cpu_var() imbalance in perf by Jan Stancek.
- Some fixes for migration from Tyrel Datwyler.
- A new syscall to switch the cpu endian by Michael Ellerman.
- Large series from Wei Yang to implement SRIOV, reviewed and acked by Bjorn.
- A fix for the OPAL sensor driver from Cédric Le Goater.
- Fixes to get STRICT_MM_TYPECHECKS building again by Michael Ellerman.
- Large series from Daniel Axtens to make our PCI hooks per PHB rather than per
machine.
- Small patch from Sam Bobroff to explicitly abort non-suspended transactions
on syscalls, plus a test to exercise it.
- Numerous reworks and fixes for the 24x7 PMU from Sukadev Bhattiprolu.
- Small patch to enable the hard lockup detector from Anton Blanchard.
- Fix from Dave Olson for missing L2 cache information on some CPUs.
- Some fixes from Michael Ellerman to get Cell machines booting again.
- Freescale updates from Scott: Highlights include BMan device tree nodes, an
MSI erratum workaround, a couple minor performance improvements, config
updates, and misc fixes/cleanup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=03Yh
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc updates from Michael Ellerman:
- Numerous minor fixes, cleanups etc.
- More EEH work from Gavin to remove its dependency on device_nodes.
- Memory hotplug implemented entirely in the kernel from Nathan
Fontenot.
- Removal of redundant CONFIG_PPC_OF by Kevin Hao.
- Rewrite of VPHN parsing logic & tests from Greg Kurz.
- A fix from Nish Aravamudan to reduce memory usage by clamping
nodes_possible_map.
- Support for pstore on powernv from Hari Bathini.
- Removal of old powerpc specific byte swap routines by David Gibson.
- Fix from Vasant Hegde to prevent the flash driver telling you it was
flashing your firmware when it wasn't.
- Patch from Ben Herrenschmidt to add an OPAL heartbeat driver.
- Fix for an oops causing get/put_cpu_var() imbalance in perf by Jan
Stancek.
- Some fixes for migration from Tyrel Datwyler.
- A new syscall to switch the cpu endian by Michael Ellerman.
- Large series from Wei Yang to implement SRIOV, reviewed and acked by
Bjorn.
- A fix for the OPAL sensor driver from Cédric Le Goater.
- Fixes to get STRICT_MM_TYPECHECKS building again by Michael Ellerman.
- Large series from Daniel Axtens to make our PCI hooks per PHB rather
than per machine.
- Small patch from Sam Bobroff to explicitly abort non-suspended
transactions on syscalls, plus a test to exercise it.
- Numerous reworks and fixes for the 24x7 PMU from Sukadev Bhattiprolu.
- Small patch to enable the hard lockup detector from Anton Blanchard.
- Fix from Dave Olson for missing L2 cache information on some CPUs.
- Some fixes from Michael Ellerman to get Cell machines booting again.
- Freescale updates from Scott: Highlights include BMan device tree
nodes, an MSI erratum workaround, a couple minor performance
improvements, config updates, and misc fixes/cleanup.
* tag 'powerpc-4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (196 commits)
powerpc/powermac: Fix build error seen with powermac smp builds
powerpc/pseries: Fix compile of memory hotplug without CONFIG_MEMORY_HOTREMOVE
powerpc: Remove PPC32 code from pseries specific find_and_init_phbs()
powerpc/cell: Fix iommu breakage caused by controller_ops change
powerpc/eeh: Fix crash in eeh_add_device_early() on Cell
powerpc/perf: Cap 64bit userspace backtraces to PERF_MAX_STACK_DEPTH
powerpc/perf/hv-24x7: Fail 24x7 initcall if create_events_from_catalog() fails
powerpc/pseries: Correct memory hotplug locking
powerpc: Fix missing L2 cache size in /sys/devices/system/cpu
powerpc: Add ppc64 hard lockup detector support
oprofile: Disable oprofile NMI timer on ppc64
powerpc/perf/hv-24x7: Add missing put_cpu_var()
powerpc/perf/hv-24x7: Break up single_24x7_request
powerpc/perf/hv-24x7: Define update_event_count()
powerpc/perf/hv-24x7: Whitespace cleanup
powerpc/perf/hv-24x7: Define add_event_to_24x7_request()
powerpc/perf/hv-24x7: Rename hv_24x7_event_update
powerpc/perf/hv-24x7: Move debug prints to separate function
powerpc/perf/hv-24x7: Drop event_24x7_request()
powerpc/perf/hv-24x7: Use pr_devel() to log message
...
Conflicts:
tools/testing/selftests/powerpc/Makefile
tools/testing/selftests/powerpc/tm/Makefile
Pull trivial tree from Jiri Kosina:
"Usual trivial tree updates. Nothing outstanding -- mostly printk()
and comment fixes and unused identifier removals"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
goldfish: goldfish_tty_probe() is not using 'i' any more
powerpc: Fix comment in smu.h
qla2xxx: Fix printks in ql_log message
lib: correct link to the original source for div64_u64
si2168, tda10071, m88ds3103: Fix firmware wording
usb: storage: Fix printk in isd200_log_config()
qla2xxx: Fix printk in qla25xx_setup_mode
init/main: fix reset_device comment
ipwireless: missing assignment
goldfish: remove unreachable line of code
coredump: Fix do_coredump() comment
stacktrace.h: remove duplicate declaration task_struct
smpboot.h: Remove unused function prototype
treewide: Fix typo in printk messages
treewide: Fix typo in printk messages
mod_devicetable: fix comment for match_flags
The recent change to the EEH probing causes a crash on Cell because
eeh_ops is NULL.
Check if EEH is enabled and if not bail out.
Fixes: ff57b454dd ("powerpc/eeh: Do probe on pci_dn")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Merge Richard's work to support SR-IOV on PowerNV. All generic PCI
patches acked by Bjorn.
Some minor conflicts with Daniel's pci_controller_ops work.
Conflicts:
arch/powerpc/include/asm/machdep.h
arch/powerpc/platforms/powernv/pci-ioda.c
This problem appears to have been introduced in 2.6.29 by commit
93197a36a9 "Rewrite sysfs processor cache info code".
This caused lscpu to error out on at least e500v2 devices, eg:
error: cannot open /sys/devices/system/cpu/cpu0/cache/index2/size: No such file or directory
Some embedded powerpc systems use cache-size in DTS for the unified L2
cache size, not d-cache-size, so we need to allow for both DTS names.
Added a new CACHE_TYPE_UNIFIED_D cache_type_info structure to handle
this.
Fixes: 93197a36a9 ("powerpc: Rewrite sysfs processor cache info code")
Signed-off-by: Dave Olson <olson@cumulusnetworks.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The hard lockup detector uses a PMU event as a periodic NMI to
detect if we are stuck (where stuck means no timer interrupts have
occurred).
Ben's rework of the ppc64 soft disable code has made ppc64 PMU
exceptions a partial NMI. They can get disabled if an external
interrupt comes in, but otherwise PMU interrupts will fire in
interrupt disabled regions.
We disable the hard lockup detector by default for a few reasons:
- It breaks userspace event based branches on POWER8.
- It is likely to produce false positives on KVM guests.
- Since PMCs can only count to 2^31, counting cycles means we might
take multiple PMU exceptions per second per hardware thread even
if our hard lockup timeout is 10 seconds.
It can be enabled via a boot option, or via procfs.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch changes the syscall handler to doom (tabort) active
transactions when a syscall is made and return immediately without
performing the syscall.
Currently, the system call instruction automatically suspends an
active transaction which causes side effects to persist when an active
transaction fails.
This does change the kernel's behaviour, but in a way that was
documented as unsupported. It doesn't reduce functionality because
syscalls will still be performed after tsuspend. It also provides a
consistent interface and makes the behaviour of user code
substantially the same across powerpc and platforms that do not
support suspended transactions (e.g. x86 and s390).
Performance measurements using
http://ozlabs.org/~anton/junkcode/null_syscall.c
indicate the cost of a system call increases by about 0.5%.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Acked-By: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Remove shims, patch callsites to use pci_controller_ops
versions instead.
Also move back the probe mode defines, as explained in the patch
for pci_probe_mode.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move the installation of DMA operations out of swiotlb's subsys
initcall, and into the generic PCI controller operations struct.
These ops are installed conditionally, based on the ppc_swiotlb_enable
global. The global can be set in two places:
- swiotlb_detect_4g, which is always called at the arch initcall level
- setup_pci_atmu, which is called as part of the fsl_add_bridge and
fsl_pci_syscore_do_resume.
fsl_pci_syscore_do_resume is called late enough that any changes as a
result of that call will have no effect.
As such, if we test the global and set the operations as part of
fsl_add_bridge, after the call to setup_pci_atmu, we can be confident
that it will cover all the PCI implementations affected by the changes
to dma-swiotlb.c.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add pci_controller_ops.reset_secondary_bus,
shadowing ppc_md.pcibios_reset_secondary_bus.
Add a shim, and changes the callsites to use the shim.
Use pcibios_reset_secondary_bus_shim, as both
pcibios_reset_secondary_bus and pci_reset_secondary_bus
are already taken.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add pci_controller_ops.window_alignment,
shadowing ppc_md.pcibios_window_alignment.
Add a shim, and changes the callsites to use the shim.
Here, we use pci_window_alignment, as pcibios_window_alignment is
already taken.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add pci_controller_ops.enable_device_hook,
shadowing ppc_md.pcibios_enable_device_hook.
Add a shim, and changes the callsites to use the shim.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add pci_controller_ops.probe_mode, shadowing ppc_md.pci_probe_mode.
Add a shim, and changes the callsites to use the shim.
We also need to move the probe mode defines to pci-bridge.h from pci.h.
They are required by the shim in order to return a sensible default.
Previously, the were defined in pci.h, but pci.h includes pci-bridge.h
before the relevant #defines. This means the definitions are absent
if pci.h is included before pci-bridge.h. This occurs in some drivers.
So, move the definitons now, and move them back when we remove the shim.
Anything that wants the defines would have had to include pci.h, and
since pci.h includes pci-bridge.h, nothing will lose access to the
defines.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add pci_controller_ops.dma_bus_setup, shadowing ppc_md.pci_dma_bus_setup.
Add a shim, and changes the callsites to use the shim.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Introduces the pci_controller_ops structure.
Add pci_controller_ops.dma_dev_setup, shadowing ppc_md.pci_dma_dev_setup.
Add a shim, and change the callsites to use the shim.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
pcibios_enable_device_hook returned an int. Every implementation
returned either -EINVAL or 0. The return value wasn't propagated by
the caller: any non-zero return value caused pcibios_enable_device
to return -EINVAL itself. Therefore, make the hook return a bool.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Previously, find_and_init_phbs() was used in both PowerNV and pSeries
setup. However, since RTAS support has been dropped from PowerNV, we
can move it into a platform-specific file.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We get way too many bug reports that say "the kernel is hung in
prom_init", which stems from the fact that the last piece of output
people see is "returning from prom_init".
The kernel is almost never hung in prom_init(), it's just that it's
crashed somewhere after prom_init() but prior to the console coming up.
The existing message should give a clue to that, ie. "returning from"
indicates that prom_init() has finished, but it doesn't seem to work.
Let's try something different.
This prints:
Quiescing Open Firmware ...
Booting Linux via __start() ...
Which hopefully makes it clear that prom_init() is not the problem, and
although __start() probably isn't either, it's at least the right place
to begin looking.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Wistfully-Acked-by: Jeremy Kerr <jk@ozlabs.org>
We have a powerpc specific global called mem_init_done which is "set on
boot once kmalloc can be called".
But that's not *quite* true. We set it at the bottom of mem_init(), and
rely on the fact that mm_init() calls kmem_cache_init() immediately
after that, and nothing is running in parallel.
So replace it with the generic and 100% correct slab_is_available().
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The celleb code has seen no actual development for ~7 years.
We (maintainers) have no access to test hardware, and it is highly
likely the code has bit-rotted.
As far as we're aware the hardware was never widely available, and is
certainly no longer available, and no one on the list has shown any
interest in it over the years.
So remove it. If anyone has one and cares please speak up.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
The function eeh_add_parent_pe() is used to create a PE or add one
edev to its parent PE. Current code checks if PE#0 is valid for the
later case. Actually, we should validate PE#0 for both cases when
EEH core regards PE#0 as invalid one (without flag EEH_VALID_PE_ZERO).
Otherwise, not all EEH devices can be added to its parent PE#0 for
EEH on P7IOC.
The patch fixes the issue by validating PE#0 for the two cases. So far,
we don't have PE#0 for EEH on P7IOC, but it will show up when we enable
M64 for P7IOC. The patch also makes the error message more meaningful.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On PowerNV platform, resource position in M64 BAR implies the PE# the
resource belongs to. In some cases, adjustment of a resource is necessary
to locate it to a correct position in M64 BAR .
This patch adds pnv_pci_vf_resource_shift() to shift the 'real' PF IOV BAR
address according to an offset.
Note:
After doing so, there would be a "hole" in the /proc/iomem when offset
is a positive value. It looks like the device return some mmio back to
the system, which actually no one could use it.
[bhelgaas: rework loops, rework overlap check, index resource[]
conventionally, remove pci_regs.h include, squashed with next patch]
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Implement pcibios_iov_resource_alignment() on powernv platform.
On PowerNV platform, there are 3 cases for the IOV BAR:
1. initial state, the IOV BAR size is multiple times of VF BAR size
2. after expanded, the IOV BAR size is expanded to meet the M64 segment size
3. sizing stage, the IOV BAR is truncated to 0
pnv_pci_iov_resource_alignment() handle these three cases respectively.
[bhelgaas: adjust to drop "align" parameter, return pci_iov_resource_size()
if no ppc_md machdep_call version]
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On PHB3, PF IOV BAR will be covered by M64 BAR to have better PE isolation.
M64 BAR is a type of hardware resource in PHB3, which could map a range of
MMIO to PE numbers on powernv platform. And this range is divided equally
by the number of total_pe with each divided range mapping to a PE number.
Also, the M64 BAR must map a MMIO range with power-of-two size.
The total_pe number is usually different from total_VFs, which can lead to
a conflict between MMIO space and the PE number.
For example, if total_VFs is 128 and total_pe is 256, the second half of
M64 BAR will be part of other PCI device, which may already belong to other
PEs.
This patch prevents the conflict by reserving additional space for the PF
IOV BAR, which is total_pe number of VF's BAR size.
[bhelgaas: make dev_printk() output more consistent, index resource[]
conventionally]
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Flag PCI_REASSIGN_ALL_RSRC is used to ignore resources information setup by
firmware, so that kernel would re-assign all resources of pci devices.
On powerpc arch, this happens in a header fixup function
pcibios_fixup_resources(), which will clean up the resources if this flag
is set. This works fine for PFs, since after clean up, kernel will
re-assign the resources in pcibios_resource_survey().
Below is a simple call flow on how it works:
pcibios_init
pcibios_scan_phb
pci_scan_child_bus
...
pci_device_add
pci_fixup_device(pci_fixup_header)
pcibios_fixup_resources # header fixup
for (i = 0; i < DEVICE_COUNT_RESOURCE; i++)
dev->resource[i].start = 0
pcibios_resource_survey # re-assign
pcibios_allocate_resources
However, the VF resources won't be re-assigned, since the VF resources are
completely determined by the PF resources, and the PF resources have
already been reassigned. This means we need to leave VF's resources
un-cleared in pcibios_fixup_resources().
In this patch, we skip the resource unset process in
pcibios_fixup_resources(), if the pci_dev is a VF.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pci_dn is the extension of PCI device node and is created from device node.
Unfortunately, VFs are enabled dynamically by PF's driver and they don't
have corresponding device nodes and pci_dn, which is required to access
VFs' config spaces.
The patch creates pci_dn for VFs in pcibios_sriov_enable() on their PF,
and removes pci_dn for VFs in pcibios_sriov_disable() on their PF. When
VF's pci_dn is created, it's put to the child list of the pci_dn of PF's
upstream bridge. The pci_dn is linked to pci_dev during early fixup time
to setup the fast path.
[bhelgaas: add ifdef around add_one_dev_pci_info(), use dev_printk()]
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We currently have a "special" syscall for switching endianness. This is
syscall number 0x1ebe, which is handled explicitly in the 64-bit syscall
exception entry.
That has a few problems, firstly the syscall number is outside of the
usual range, which confuses various tools. For example strace doesn't
recognise the syscall at all.
Secondly it's handled explicitly as a special case in the syscall
exception entry, which is complicated enough without it.
As a first step toward removing the special syscall, we need to add a
regular syscall that implements the same functionality.
The logic is simple, it simply toggles the MSR_LE bit in the userspace
MSR. This is the same as the special syscall, with the caveat that the
special syscall clobbers fewer registers.
This version clobbers r9-r12, XER, CTR, and CR0-1,5-7.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
During suspend/migration operation we must wait for the VASI state reported
by the hypervisor to become Suspending prior to making the ibm,suspend-me
RTAS call. Calling routines to rtas_ibm_supend_me() pass a vasi_state variable
that exposes the VASI state to the caller. This is unnecessary as the caller
only really cares about the following three conditions; if there is an error
we should bailout, success indicating we have suspended and woken back up so
proceed to device tree update, or we are not suspendable yet so try calling
rtas_ibm_suspend_me again shortly.
This patch removes the extraneous vasi_state variable and simply uses the
return code to communicate how to proceed. We either succeed, fail, or get
-EAGAIN in which case we sleep for a second before trying to call
rtas_ibm_suspend_me again. The behaviour of ppc_rtas() remains the same,
but migrate_store() now returns the propogated error code on failure.
Previously -1 was returned from migrate_store() in the failure case which
equates to -EPERM and was clearly wrong.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Cc: Nathan Fontenont <nfont@linux.vnet.ibm.com>
Cc: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The patch removes struct eeh_dev::dn and the corresponding helper
functions: eeh_dev_to_of_node() and of_node_to_eeh_dev(). Instead,
eeh_dev_to_pdn() and pdn_to_eeh_dev() should be used to get the
pdn, which might contain device_node on PowerNV platform.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There are 3 EEH operations whose arguments contain device_node:
read_config(), write_config() and restore_config(). The patch
replaces device_node with pci_dn.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Originally, EEH core probes on device_node or pci_dev to populate
EEH devices and PEs, which conflicts with the fact: SRIOV VFs are
usually enabled and created by PF's driver and they don't have the
corresponding device_nodes. Instead, SRIOV VFs have dynamically
created pci_dn, which can be used for EEH probe.
The patch reworks EEH probe for PowerNV and pSeries platforms to
do probing based on pci_dn, instead of pci_dev or device_node any
more.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch adds function traverse_pci_dn(), which is similar to
traverse_pci_devices() except it takes pci_dn, not device_node
as parameter. The pci_dev.c has been reworked to create eeh_dev
from pci_dn, instead of device_node.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Originally, EEH probes on device_node or pci_dev and populates the
corresponding eeh_dev. In the subsequent patches, EEH will probes
on pci_dn and populates the corresponding eeh_dev. So we have to
cache some information in pci_dn, either from device_node or SRIOV
PF's enablement platform hook, to populate the eeh_dev properly.
The motivation to probe pci_dn, instead of device node or pci_dev,
to populate eeh_dev is SRIOV VFs are dynamically created and we
don't have the corresponding device nodes for them.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, the PCI config accessors are implemented based on device node.
Unfortunately, SRIOV VFs won't have the corresponding device nodes. pci_dn
will be used in replacement with device node for SRIOV VFs. So we have to
use pci_dn in PCI config accessors.
The patch refactors pci_dn in following aspects to make it ready to be used
in PCI config accessors as we do in subsequent patch:
* pci_dn is organized as a hierarchy tree. PCI device's pci_dn is
put to the child list of pci_dn of its upstream bridge or PHB. VF's
pci_dn will be put to the child list of pci_dn of PF's bridge.
* For one particular PCI device (VF or not), its pci_dn can be
found from pdev->dev.archdata.pci_data, PCI_DN(devnode), or
parent's list. The fast path (fetching pci_dn through PCI device
instance) is populated during early fixup time.
[bhelgaas: changelog]
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
commit id 2ba9f0d has changed CONFIG_KVM_BOOK3S_64_HV to tristate to allow
HV/PR bits to be built as modules. But the MCE code still depends on
CONFIG_KVM_BOOK3S_64_HV which is wrong. When user selects
CONFIG_KVM_BOOK3S_64_HV=m to build HV/PR bits as a separate module the
relevant MCE code gets excluded.
This patch fixes the MCE code to use CONFIG_KVM_BOOK3S_64_HANDLER. This
makes sure that the relevant MCE code is included when HV/PR bits
are built as a separate modules.
Fixes: 2ba9f0d887 ("kvm: powerpc: book3s: Support building HV and PR KVM as module")
Cc: stable@vger.kernel.org # v3.14+
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The power7_nap(), power7_sleep() and power7_winkle() functions are
called from pnv_smp_cpu_kill_self(), which expects them to return the
SRR1 value set by the hardware on wakeup, or 0 if no nap/sleep/winkle
occurred. However, in the case where an interrupt needs to be
replayed, the logic in power7_powersave_common (the common code for
power7_nap et al.) doesn't set r3 to 0 in this case. Instead what we
get as the return value is the selector for the type of power-saving
mode requested (1, 2 or 3). In fact this should not affect the
operation of pnv_smp_cpu_kill_self(), but it is better to get this
correct, so this adds an instruction to set r3 to 0 in this case.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
While we are here, let us make timestamp related code y2038-safe.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch extends pstore, a generic interface to platform dependent
persistent storage, support for powernv platform to capture certain
useful information, during dying moments. Such support is already in
place for pseries platform. This patch re-uses most of that code.
It is a common practice to compile kernels with both CONFIG_PPC_PSERIES=y
and CONFIG_PPC_POWERNV=y. The code in nvram_init_oops_partition() routine
still works as intended, as the caller is platform specific code which
passes the appropriate value for "rtas_partition_exists" parameter.
In all other places, where CONFIG_PPC_PSERIES or CONFIG_PPC_POWERNV
flag is used in this patchset, it is to reduce the kernel size in cases
where this flag is not set and doesn't have any impact logic wise.
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With minor checks, we can move most of the code for nvram
under pseries to a common place to be re-used by other
powerpc platforms like powernv. This patch moves such
common code to arch/powerpc/kernel/nvram_64.c file.
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
[mpe: Move select of ZLIB_DEFLATE to PPC64 to fix the build]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There's a new variant of POWER8 coming called "POWER8 with NVLink". The
core is identical to POWER8 but unfortunately they strapped it with a
different PVR, so we need to add an explicit entry for it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since we can now use hypervisor doorbells for host IPIs, this makes
sure we clear the host IPI flag when taking a doorbell interrupt, and
clears any pending doorbell IPI in pnv_smp_cpu_kill_self() (as we
already do for IPIs sent via the XICS interrupt controller). Otherwise
if there did happen to be a leftover pending doorbell interrupt for
an offline CPU thread for any reason, it would prevent that thread from
going into a power-saving mode; it would instead keep waking up because
of the interrupt.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The 'arg' argument to copy_thread() is only ever used when forking a new
kernel thread. Hence, rename it to 'kthread_arg' for clarity.
Signed-off-by: Alex Dowad <alexinbeijing@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We have set CONFIG_PPC_OF to always 'y' in commit 0a498d96a3
("powerpc: set CONFIG_PPC_OF=y always for ARCH=powerpc") nine years
ago. And the arch/ppc also has gone away for many years. The OF
functionality was also moved to a common place and be used by many
archs. So it does make no sense to keep such a option in the current
kernel. Just kill it.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Function pcibios_set_pcie_reset_state() is possibly called by
pci_reset_function(), on which VFIO infrastructure depends to
issue reset. pcibios_set_pcie_reset_state() is issuing reset
on the parent PE of the indicated PCI device. The reset causes
state lost on all PCI devices except the indicated one as the
argument to pcibios_set_pcie_reset_state(). Also, sideband
MMIO access from guest when issuing reset would cause unexpected
EEH error.
For above two issues, the patch applies following enhancements
to pcibios_set_pcie_reset_state():
* For all PCI devices except the indicated one, save their
state prior to reset and restore state after that.
* Explicitly freeze PE prior to reset and unfreeze it after
that, in order to avoid unexpected EEH error.
Tested-by: Priya M. A <priyama2@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The flush_tlb hook in cpu_spec was introduced as a generic function hook
to invalidate TLBs. But the current implementation of flush_tlb hook
takes IS (invalidation selector) as an argument which is architecture
dependent. Hence, It is not right to have a generic routine where caller
has to pass non-generic argument.
This patch fixes this and makes flush_tlb hook as high level API.
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As our various loops (copy, string, crypto etc) get more complicated,
we want to share implementations between userspace (eg glibc) and
the kernel. We also want to write userspace test harnesses to put
in tools/testing/selftest.
One gratuitous difference between userspace and the kernel is the
VMX register definitions - the kernel uses vrX whereas both gcc and
glibc use vX.
Change the kernel to match userspace.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
After d905c5df9a ("PPC: POWERNV: move iommu_add_device earlier"), the
refcnt on the kobject backing the IOMMU group for a PCI device is
elevated by each call to pci_dma_dev_setup_pSeriesLP() (via
set_iommu_table_base_and_group). When we go to dlpar a multi-function
PCI device out:
iommu_reconfig_notifier ->
iommu_free_table ->
iommu_group_put
BUG_ON(tbl->it_group)
We trip this BUG_ON, because there are still references on the table, so
it is not freed. Fix this by moving the powernv bus notifier to common
code and calling it for both powernv and pseries.
Fixes: d905c5df9a ("PPC: POWERNV: move iommu_add_device earlier")
Signed-off-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Tested-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Anton has a busy ppc64le KVM box where guests sometimes hit the infamous
"kernel BUG at kernel/smpboot.c:134!" issue during boot:
BUG_ON(td->cpu != smp_processor_id());
Basically a per CPU hotplug thread scheduled on the wrong CPU. The oops
output confirms it:
CPU: 0
Comm: watchdog/130
The problem is that we aren't ensuring the CPU active bit is set for the
secondary before allowing the master to continue on. The master unparks
the secondary CPU's kthreads and the scheduler looks for a CPU to run
on. It calls select_task_rq() and realises the suggested CPU is not in
the cpus_allowed mask. It then ends up in select_fallback_rq(), and
since the active bit isnt't set we choose some other CPU to run on.
This seems to have been introduced by 6acbfb9697 "sched: Fix hotplug
vs. set_cpus_allowed_ptr()", which changed from setting active before
online to setting active after online. However that was in turn fixing a
bug where other code assumed an active CPU was also online, so we can't
just revert that fix.
The simplest fix is just to spin waiting for both active & online to be
set. We already have a barrier prior to set_cpu_online() (which also
sets active), to ensure all other setup is completed before online &
active are set.
Fixes: 6acbfb9697 ("sched: Fix hotplug vs. set_cpus_allowed_ptr()")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
enhancements and fixes mostly for ARM32, ARM64, MIPS and Power-based
devices. Additionaly the framework core underwent a bit of surgery with
two major changes. The boundary between the clock core and clock
providers (e.g clock drivers) is now more well defined with dedicated
provider helper functions. struct clk no longer maps 1:1 with the
hardware clock but is a true per-user cookie which helps us tracker
users of hardware clocks and debug bad behavior. The second major change
is the addition of rate constraints for clocks. Rate ranges are now
supported which are analogous to the voltage ranges in the regulator
framework. Unfortunately these changes to the core created some
breakeage. We think we fixed it all up but for this reason there are
lots of last minute commits trying to undo the damage.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJU54D5AAoJEDqPOy9afJhJs6AQAK5YuUwjDchdpNZx9p7OnT1q
+poehuUwE/gYjmdACqYFyaPrI/9f43iNCfFAgKGLQqmB5ZK4sm4ktzfBEhjWINR2
iiCx9QYMQVGiKwC8KU0ddeBciglE2b/DwxB45m9TsJEjowucUeBzwLEIj5DsGxf7
teXRoOWgXdz1MkQJ4pnA09Q3qEPQgmu8prhMfka/v75/yn7nb9VWiJ6seR2GqTKY
sIKL9WbKjN4AzctggdqHnMSIqZoq6vew850bv2C1fPn7GiYFQfWW+jvMlVY40dp8
nNa2ixSQSIXVw4fCtZhTIZcIvZ8puc7WVLcl8fz3mUe3VJn1VaGs0E+Yd3GexpIV
7bwkTOIdS8gSRlsUaIPiMnUob5TUMmMqjF4KIh/AhP4dYrmVbU7Ie8ccvSxe31Ku
lK7ww6BFv3KweTnW/58856ZXDlXLC6x3KT+Fw58L23VhPToFgYOdTxn8AVtE/LKP
YR3UnY9BqFx6WHXVoNvg3Piyej7RH8fYmE9om8tyWc/Ab8Eo501SHs9l3b2J8snf
w/5STd2CYxyKf1/9JLGnBvGo754O9NvdzBttRlygB14gCCtS/SDk/ELG2Ae+/a9P
YgRk2+257h8PMD3qlp94dLidEZN4kYxP/J6oj0t1/TIkERWfZjzkg5tKn3/hEcU9
qM97ZBTplTm6FM+Dt/Vk
=zCVK
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.20' of git://git.linaro.org/people/mike.turquette/linux
Pull clock framework updates from Mike Turquette:
"The clock framework changes contain the usual driver additions,
enhancements and fixes mostly for ARM32, ARM64, MIPS and Power-based
devices.
Additionally the framework core underwent a bit of surgery with two
major changes:
- The boundary between the clock core and clock providers (e.g clock
drivers) is now more well defined with dedicated provider helper
functions. struct clk no longer maps 1:1 with the hardware clock
but is a true per-user cookie which helps us tracker users of
hardware clocks and debug bad behavior.
- The addition of rate constraints for clocks. Rate ranges are now
supported which are analogous to the voltage ranges in the
regulator framework.
Unfortunately these changes to the core created some breakeage. We
think we fixed it all up but for this reason there are lots of last
minute commits trying to undo the damage"
* tag 'clk-for-linus-3.20' of git://git.linaro.org/people/mike.turquette/linux: (113 commits)
clk: Only recalculate the rate if needed
Revert "clk: mxs: Fix invalid 32-bit access to frac registers"
clk: qoriq: Add support for the platform PLL
powerpc/corenet: Enable CLK_QORIQ
clk: Replace explicit clk assignment with __clk_hw_set_clk
clk: Add __clk_hw_set_clk helper function
clk: Don't dereference parent clock if is NULL
MIPS: Alchemy: Remove bogus args from alchemy_clk_fgcs_detr
clkdev: Always allocate a struct clk and call __clk_get() w/ CCF
clk: shmobile: div6: Avoid division by zero in .round_rate()
clk: mxs: Fix invalid 32-bit access to frac registers
clk: omap: compile legacy omap3 clocks conditionally
clkdev: Export clk_register_clkdev
clk: Add rate constraints to clocks
clk: remove clk-private.h
pci: xgene: do not use clk-private.h
arm: omap2+ remove dead clock code
clk: Make clk API return per-user struct clk instances
clk: tegra: Define PLLD_DSI and remove dsia(b)_mux
clk: tegra: Add support for the Tegra132 CAR IP block
...
Add a new kexec preprocessor macro IND_FLAGS, which is the bitwise OR of
all the possible kexec IND_ kimage_entry indirection flags. Having this
macro allows for simplified code in the prosessing of the kexec
kimage_entry items. Also, remove the local powerpc definition and use the
generic one.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Maximilian Attems <max@stro.at>
Cc: Michal Marek <mmarek@suse.cz>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
printk and friends can now format bitmaps using '%*pb[l]'. cpumask
and nodemask also provide cpumask_pr_args() and nodemask_pr_args()
respectively which can be used to generate the two printf arguments
necessary to format the specified cpu/nodemask.
* Spurious if (len > 1) test dropped from shared_cpu_map_show().
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On POWER8 virtualised kernels the VTB register can be read to have a view
of time that only increases while the guest is running. This will prevent
guests from seeing time jump if a guest is paused for significant amounts
of time.
On POWER7 and below virtualised kernels stolen time is subtracted from
local_clock as a best effort approximation. This will not eliminate
spurious warnings in the case of a suspended guest but may reduce the
occurance in the case of softlockups due to host over commit.
Bare metal kernels should avoid reading the VTB as KVM does not restore
sane values when not executing, the approxmation is fine as host kernels
won't observe any stolen time.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Andrew Jones <drjones@redhat.com>
Acked-by: Don Zickus <dzickus@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Ulrich Obergfell <uobergfe@redhat.com>
Cc: chai wen <chaiw.fnst@cn.fujitsu.com>
Cc: Fabian Frederick <fabf@skynet.be>
Cc: Aaron Tomlin <atomlin@redhat.com>
Cc: Ben Zhang <benzh@chromium.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If an attacker can cause a controlled kernel stack overflow, overwriting
the restart block is a very juicy exploit target. This is because the
restart_block is held in the same memory allocation as the kernel stack.
Moving the restart block to struct task_struct prevents this exploit by
making the restart_block harder to locate.
Note that there are other fields in thread_info that are also easy
targets, at least on some architectures.
It's also a decent simplification, since the restart code is more or less
identical on all architectures.
[james.hogan@imgtec.com: metag: align thread_info::supervisor_stack]
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: David Miller <davem@davemloft.net>
Acked-by: Richard Weinberger <richard@nod.at>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Tested-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Chen Liqin <liqin.linux@gmail.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Including:
- Update of all defconfigs
- Addition of a bunch of config options to modernise our defconfigs
- Some PS3 updates from Geoff
- Optimised memcmp for 64 bit from Anton
- Fix for kprobes that allows 'perf probe' to work from Naveen
- Several cxl updates from Ian & Ryan
- Expanded support for the '24x7' PMU from Cody & Sukadev
- Freescale updates from Scott:
"Highlights include 8xx optimizations, some more work on datapath device
tree content, e300 machine check support, t1040 corenet error reporting,
and various cleanups and fixes."
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xDU3
-----END PGP SIGNATURE-----
Merge tag 'powerpc-3.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc updates from Michael Ellerman:
- Update of all defconfigs
- Addition of a bunch of config options to modernise our defconfigs
- Some PS3 updates from Geoff
- Optimised memcmp for 64 bit from Anton
- Fix for kprobes that allows 'perf probe' to work from Naveen
- Several cxl updates from Ian & Ryan
- Expanded support for the '24x7' PMU from Cody & Sukadev
- Freescale updates from Scott:
"Highlights include 8xx optimizations, some more work on datapath
device tree content, e300 machine check support, t1040 corenet
error reporting, and various cleanups and fixes"
* tag 'powerpc-3.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (102 commits)
cxl: Add missing return statement after handling AFU errror
cxl: Fail AFU initialisation if an invalid configuration record is found
cxl: Export optional AFU configuration record in sysfs
powerpc/mm: Warn on flushing tlb page in kernel context
powerpc/powernv: Add OPAL soft-poweroff routine
powerpc/perf/hv-24x7: Document sysfs event description entries
powerpc/perf/hv-gpci: add the remaining gpci requests
powerpc/perf/{hv-gpci, hv-common}: generate requests with counters annotated
powerpc/perf/hv-24x7: parse catalog and populate sysfs with events
perf: define EVENT_DEFINE_RANGE_FORMAT_LITE helper
perf: add PMU_EVENT_ATTR_STRING() helper
perf: provide sysfs_show for struct perf_pmu_events_attr
powerpc/kernel: Avoid initializing device-tree pointer twice
powerpc: Remove old compile time disabled syscall tracing code
powerpc/kernel: Make syscall_exit a local label
cxl: Fix device_node reference counting
powerpc/mm: bail out early when flushing TLB page
powerpc: defconfigs: add MTD_SPI_NOR (new dependency for M25P80)
perf/powerpc: reset event hw state when adding it to the PMU
powerpc/qe: Use strlcpy()
...
Freescale updates from Scott:
"Highlights include 8xx optimizations, some more work on datapath device
tree content, e300 machine check support, t1040 corenet error reporting,
and various cleanups and fixes."
As commit 50ba08f3 ("of/fdt: Don't clear initial_boot_params
if fdt_check_header() fails") does, the device-tree pointer
"initial_boot_params" is initialized by early_init_dt_verify(),
which is called by early_init_devtree(). So we needn't explicitly
initialize that again in early_init_devtree().
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We have code to do syscall tracing which is disabled at compile time by
default. It's not been touched since the dawn of time (ie. v2.6.12).
There are now better ways to do syscall tracing, ie. using the
raw_syscall, or syscall tracepoints.
For the specific case of tracing syscalls at boot on a system that
doesn't get to userspace, you can boot with:
trace_event=syscalls tp_printk=on
Which will trace syscalls from boot, and echo all output to the console.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently when we back trace something that is in a syscall we see
something like this:
[c000000000000000] [c000000000000000] SyS_read+0x6c/0x110
[c000000000000000] [c000000000000000] syscall_exit+0x0/0x98
Although it's entirely correct, seeing syscall_exit at the bottom can be
confusing - we were exiting from a syscall and then called SyS_read() ?
If we instead change syscall_exit to be a local label we get something
more intuitive:
[c0000001fa46fde0] [c00000000026719c] SyS_read+0x6c/0x110
[c0000001fa46fe30] [c000000000009264] system_call+0x38/0xd0
ie. we were handling a system call, and it was SyS_read().
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
All accessed to PGD entries are done via 0(r11).
By using lower part of swapper_pg_dir as load index to r11, we can remove the
ori instruction.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
L1 base address is now aligned so we can insert L1 index into r11 directly and
then preserve r10
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Kernel MMU handling code handles validity of entries via _PMD_PRESENT which
corresponds to V bit in MD_TWC and MI_TWC. When the V bit is not set, MPC8xx
triggers TLBError exception. So we don't have to check that and branch ourself
to TLBError. We can set TLB entries with non present entries, remove all those
tests and let the 8xx handle it. This reduce the number of cycle when the
entries are valid which is the case most of the time, and doesn't significantly
increase the time for handling invalid entries.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Since commit 33fb845a6f ("powerpc/8xx: Don't use MD_TWC for walk"), MD_EPN and
MD_TWC are not writen anymore in FixupDAR so saving r3 has become useless.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
On powerpc 8xx, in TLB entries, 0x400 bit is set to 1 for read-only pages
and is set to 0 for RW pages. So we should use _PAGE_RO instead of _PAGE_RW
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Remove slice_set_psize() which is not used.
It was added in 3a8247cc2c "powerpc: Only demote individual slices
rather than whole process" but was never used.
Remove vsx_assist_exception() which is not used.
It was added in ce48b21007 "powerpc: Add VSX context save/restore,
ptrace and signal support" but was never used.
Remove generic_mach_cpu_die() which is not used.
Its last caller was removed in 375f561a41 "powerpc/powernv: Always go
into nap mode when CPU is offline".
Remove mpc7448_hpc2_power_off() and mpc7448_hpc2_halt() which are
unused.
These were introduced in c5d56332fd "[POWERPC] Add general support for
mpc7448hpc2 (Taiga) platform" but were never used.
This was partially found by using a static code analysis program called
cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
[mpe: Update changelog with details on when/why they are unused]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
RTAS events require arguments be passed in big endian while hypercalls
have their arguments passed in registers and the values should therefore
be in CPU endian.
The "ibm,suspend_me" 'RTAS' call makes a sequence of hypercalls to setup
one true RTAS call. This means that "ibm,suspend_me" is handled
specially in the ppc_rtas() syscall.
The ppc_rtas() syscall has its arguments in big endian and can therefore
pass these arguments directly to the RTAS call. "ibm,suspend_me" is
handled specially from within ppc_rtas() (by calling rtas_ibm_suspend_me())
which has left an endian bug on little endian systems due to the
requirement of hypercalls. The return value from rtas_ibm_suspend_me()
gets returned in cpu endian, and is left unconverted, also a bug on
little endian systems.
rtas_ibm_suspend_me() does not actually make use of the rtas_args that
it is passed. This patch removes the convoluted use of the rtas_args
struct to pass params to rtas_ibm_suspend_me() in favour of passing what
it needs as actual arguments. This patch also ensures the two callers of
rtas_ibm_suspend_me() pass function parameters in cpu endian and in the
case of ppc_rtas(), converts the return value.
migrate_store() (the other caller of rtas_ibm_suspend_me()) is from a
sysfs file which deals with everything in cpu endian so this function
only underwent cleanup.
This patch has been tested with KVM both LE and BE and on PowerVM both
LE and BE. Under QEMU/KVM the migration happens without touching these
code pathes.
For PowerVM there is no obvious regression on BE and the LE code path
now provides the correct parameters to the hypervisor.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Resource management
- Clip bridge windows to fit in upstream windows (Yinghai Lu)
Virtualization
- Mark Atheros AR93xx to avoid using bus reset (Alex Williamson)
Miscellaneous
- Update Richard Zhu's email address (Lucas Stach)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HRy7
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.19-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"These are fixes for:
- a resource management problem that causes a Radeon "Fatal error
during GPU init" on machines where the BIOS programmed an invalid
Root Port window. This was a regression in v3.16.
- an Atheros AR93xx device that doesn't handle PCI bus resets
correctly. This was a regression in v3.14.
- an out-of-date email address"
* tag 'pci-v3.19-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
MAINTAINERS: Update Richard Zhu's email address
sparc/PCI: Clip bridge windows to fit in upstream windows
powerpc/PCI: Clip bridge windows to fit in upstream windows
parisc/PCI: Clip bridge windows to fit in upstream windows
mn10300/PCI: Clip bridge windows to fit in upstream windows
microblaze/PCI: Clip bridge windows to fit in upstream windows
ia64/PCI: Clip bridge windows to fit in upstream windows
frv/PCI: Clip bridge windows to fit in upstream windows
alpha/PCI: Clip bridge windows to fit in upstream windows
x86/PCI: Clip bridge windows to fit in upstream windows
PCI: Add pci_claim_bridge_resource() to clip window if necessary
PCI: Add pci_bus_clip_resource() to clip to fit upstream window
PCI: Pass bridge device, not bus, when updating bridge windows
PCI: Mark Atheros AR93xx to avoid bus reset
PCI: Add flag for devices where we can't use bus reset
When PE's frozen count hits maximal allowed frozen times, which is
5 currently, it will be forced to be offline permanently. Once the
PE is removed permanently, rebooting machine is required to bring
the PE back. It's not convienent when testing EEH functionality.
The patch exports the maximal allowed frozen times through debugfs
entry (/sys/kernel/debug/powerpc/eeh_max_freezes).
Requested-by: Ryan Grimm <grimm@linux.vnet.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The conditions that one specific PE's frozen count exceeds the maximal
allowed times (EEH_MAX_ALLOWED_FREEZES) and it's in isolated or recovery
state indicate the PE was removed permanently implicitly. The patch
introduces flag EEH_PE_REMOVED to indicate that explicitly so that we
don't depend on the fixed maximal allowed times, which can be varied as
we do in subsequent patch.
Flag EEH_PE_REMOVED is expected to be marked for the PE whose frozen
count exceeds the maximal allowed times, or just failed from recovery.
Requested-by: Ryan Grimm <grimm@linux.vnet.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PE#0 should be regarded as valid for P7IOC, while it's invalid for
PHB3. The patch adds flag EEH_VALID_PE_ZERO to differentiate those
two cases. Without the patch, we possibly see frozen PE#0 state is
cleared without EEH recovery taken on P7IOC as following kernel logs
indicate:
[root@ltcfbl8eb ~]# dmesg
:
pci 0000:00 : [PE# 000] Secondary bus 0 associated with PE#0
pci 0000:01 : [PE# 001] Secondary bus 1 associated with PE#1
pci 0001:00 : [PE# 000] Secondary bus 0 associated with PE#0
pci 0001:01 : [PE# 001] Secondary bus 1 associated with PE#1
pci 0002:00 : [PE# 000] Secondary bus 0 associated with PE#0
pci 0002:01 : [PE# 001] Secondary bus 1 associated with PE#1
pci 0003:00 : [PE# 000] Secondary bus 0 associated with PE#0
pci 0003:01 : [PE# 001] Secondary bus 1 associated with PE#1
pci 0003:20 : [PE# 002] Secondary bus 32..63 associated with PE#2
:
EEH: Clear non-existing PHB#3-PE#0
EEH: PHB location: U78AE.001.WZS00M9-P1-002
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When calling to early_setup(), we pick "boot_paca" up for the master CPU
and initialize that with initialise_paca(). At that point, the SLB
shadow buffer isn't populated yet. Updating the SLB shadow buffer should
corrupt what we had in physical address 0 where the trap instruction is
usually stored.
This hasn't been observed to cause any trouble in practice, but is
obviously fishy.
Fixes: 6f4441ef70 ("powerpc: Dynamically allocate slb_shadow from memblock")
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Once upon a time, at least 9 years ago (< 2.6.12), _TIF_SYSCALL_T_OR_A
meant "TRACE or AUDIT". But these days it means TRACE or AUDIT or
SECCOMP or TRACEPOINT or NOHZ.
All of those are implemented via syscall_dotrace() so rename the flag to
that to try and clarify things.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
pci_dn->phb is set to phb in update_dn_pci_info(), if succeed.
This patch removes the duplication of pci_dn->phb initialization.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
So the boards which has COMMON_CLK enabled don't have to
invoke this in its board specific file.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Acked-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Every PCI-PCI bridge window should fit inside an upstream bridge window
because orphaned address space is unreachable from the primary side of the
upstream bridge. If we inherit invalid bridge windows that overlap an
upstream window from firmware, clip them to fit and update the bridge
accordingly.
[bhelgaas: changelog]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=85491
Reported-by: Marek Kordik <kordikmarek@gmail.com>
Fixes: 5b28541552 ("PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Paul Mackerras <paulus@samba.org>
CC: Michael Ellerman <mpe@ellerman.id.au>
CC: Gavin Shan <gwshan@linux.vnet.ibm.com>
CC: Anton Blanchard <anton@samba.org>
CC: Sebastian Ott <sebott@linux.vnet.ibm.com>
CC: Wei Yang <weiyang@linux.vnet.ibm.com>
CC: Andrew Murray <amurray@embedded-bits.co.uk>
CC: linuxppc-dev@lists.ozlabs.org
This reverts commit 7c5c92ed56.
Although this did fix the bug it was aimed at, it also broke secondary
startup on platforms that use give/take_timebase(). Unfortunately we
didn't detect that while it was in next.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We have two arrays in kvm_host_state that contain register values for
the PMU. Currently we only create an asm-offsets symbol for the base of
the arrays, and do the array offset in the assembly code.
Creating an asm-offsets symbol for each field individually makes the
code much nicer to read, particularly for the MMCRx/SIxR/SDAR fields, and
might have helped us notice the recent double restore bug we had in this
code.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Alexander Graf <agraf@suse.de>
In LE kernel, we currently have a hack for kexec that resets the exception
endian before starting a new kernel as the kernel that is loaded could be a
big endian or a little endian kernel. In kdump case, resetting exception
endian fails when one or more cpus is disabled. But we can ignore the failure
and still go ahead, as in most cases crashkernel will be of same endianess
as primary kernel and reseting endianess is not even needed in those cases.
This patch adds a new inline function to say if this is kdump path. This
function is used at places where such a check is needed.
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
[mpe: Rename to kdump_in_progress(), use bool, and edit comment]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The highlight is the series that reworks the idle management on powernv, which
allows us to use deeper idle states on those machines.
There's the fix from Anton for the "BUG at kernel/smpboot.c:134!" problem.
An i2c driver for powernv. This is acked by Wolfram Sang, and he asked that we
take it through the powerpc tree.
A fix for audit from rgb at Red Hat, acked by Paul Moore who is one of the audit
maintainers.
A patch from Ben to export the symbol map of our OPAL firmware as a sysfs file,
so that tools can use it.
Also some CXL fixes, a couple of powerpc perf fixes, a fix for smt-enabled, and
the patch to add __force to get_user() so we can use bitwise types.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=GXdK
-----END PGP SIGNATURE-----
Merge tag 'powerpc-3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull second batch of powerpc updates from Michael Ellerman:
"The highlight is the series that reworks the idle management on
powernv, which allows us to use deeper idle states on those machines.
There's the fix from Anton for the "BUG at kernel/smpboot.c:134!"
problem.
An i2c driver for powernv. This is acked by Wolfram Sang, and he
asked that we take it through the powerpc tree.
A fix for audit from rgb at Red Hat, acked by Paul Moore who is one of
the audit maintainers.
A patch from Ben to export the symbol map of our OPAL firmware as a
sysfs file, so that tools can use it.
Also some CXL fixes, a couple of powerpc perf fixes, a fix for
smt-enabled, and the patch to add __force to get_user() so we can use
bitwise types"
* tag 'powerpc-3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
powerpc/powernv: Ignore smt-enabled on Power8 and later
powerpc/uaccess: Allow get_user() with bitwise types
powerpc/powernv: Expose OPAL firmware symbol map
powernv/powerpc: Add winkle support for offline cpus
powernv/cpuidle: Redesign idle states management
powerpc/powernv: Enable Offline CPUs to enter deep idle states
powerpc/powernv: Switch off MMU before entering nap/sleep/rvwinkle mode
i2c: Driver to expose PowerNV platform i2c busses
powerpc: add little endian flag to syscall_get_arch()
power/perf/hv-24x7: Use kmem_cache_free() instead of kfree
powerpc/perf/hv-24x7: Use per-cpu page buffer
cxl: Unmap MMIO regions when detaching a context
cxl: Add timeout to process element commands
cxl: Change contexts_lock to a mutex to fix sleep while atomic bug
powerpc: Secondary CPUs must set cpu_callin_map after setting active and online
- spring cleaning: removed support for IA64, and for hardware-assisted
virtualization on the PPC970
- ARM, PPC, s390 all had only small fixes
For x86:
- small performance improvements (though only on weird guests)
- usual round of hardware-compliancy fixes from Nadav
- APICv fixes
- XSAVES support for hosts and guests. XSAVES hosts were broken because
the (non-KVM) XSAVES patches inadvertently changed the KVM userspace
ABI whenever XSAVES was enabled; hence, this part is going to stable.
Guest support is just a matter of exposing the feature and CPUID leaves
support.
Right now KVM is broken for PPC BookE in your tree (doesn't compile).
I'll reply to the pull request with a patch, please apply it either
before the pull request or in the merge commit, in order to preserve
bisectability somewhat.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJUkpg+AAoJEL/70l94x66DUmoH/jzXYkptSW9NGgm79KqxGJlD
lzLnLBkitVvx++Mz5YBhdJEhKKLUlCtifFT1zPJQ/pthQhIRSaaAwZyNGgUs5w5x
yMGKHiPQFyZRbmQtZhCInW0BftJoYHHciO3nUfHCZnp34My9MP2D55W7/z+fYFfQ
DuqBSE9ThyZJtZ4zh8NRA9fCOeuqwVYRyoBs820Wbsh4cpIBoIK63Dg7k+CLE+ZV
MZa/mRL6bAfsn9W5bnOUAgHJ3SPznnWbO3/g0aV+roL/5pffblprJx9lKNR08xUM
6hDFLop2gDehDJesDkY/o8Ckp1hEouvfsVpSShry4vcgtn0hgh2O5/6Orbmj6vE=
=Zwq1
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM update from Paolo Bonzini:
"3.19 changes for KVM:
- spring cleaning: removed support for IA64, and for hardware-
assisted virtualization on the PPC970
- ARM, PPC, s390 all had only small fixes
For x86:
- small performance improvements (though only on weird guests)
- usual round of hardware-compliancy fixes from Nadav
- APICv fixes
- XSAVES support for hosts and guests. XSAVES hosts were broken
because the (non-KVM) XSAVES patches inadvertently changed the KVM
userspace ABI whenever XSAVES was enabled; hence, this part is
going to stable. Guest support is just a matter of exposing the
feature and CPUID leaves support"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (179 commits)
KVM: move APIC types to arch/x86/
KVM: PPC: Book3S: Enable in-kernel XICS emulation by default
KVM: PPC: Book3S HV: Improve H_CONFER implementation
KVM: PPC: Book3S HV: Fix endianness of instruction obtained from HEIR register
KVM: PPC: Book3S HV: Remove code for PPC970 processors
KVM: PPC: Book3S HV: Tracepoints for KVM HV guest interactions
KVM: PPC: Book3S HV: Simplify locking around stolen time calculations
arch: powerpc: kvm: book3s_paired_singles.c: Remove unused function
arch: powerpc: kvm: book3s_pr.c: Remove unused function
arch: powerpc: kvm: book3s.c: Remove some unused functions
arch: powerpc: kvm: book3s_32_mmu.c: Remove unused function
KVM: PPC: Book3S HV: Check wait conditions before sleeping in kvmppc_vcore_blocked
KVM: PPC: Book3S HV: ptes are big endian
KVM: PPC: Book3S HV: Fix inaccuracies in ICP emulation for H_IPI
KVM: PPC: Book3S HV: Fix KSM memory corruption
KVM: PPC: Book3S HV: Fix an issue where guest is paused on receiving HMI
KVM: PPC: Book3S HV: Fix computation of tlbie operand
KVM: PPC: Book3S HV: Add missing HPTE unlock
KVM: PPC: BookE: Improve irq inject tracepoint
arm/arm64: KVM: Require in-kernel vgic for the arch timers
...
There are two ways in which a guest instruction can be obtained from
the guest in the guest exit code in book3s_hv_rmhandlers.S. If the
exit was caused by a Hypervisor Emulation interrupt (i.e. an illegal
instruction), the offending instruction is in the HEIR register
(Hypervisor Emulation Instruction Register). If the exit was caused
by a load or store to an emulated MMIO device, we load the instruction
from the guest by turning data relocation on and loading the instruction
with an lwz instruction.
Unfortunately, in the case where the guest has opposite endianness to
the host, these two methods give results of different endianness, but
both get put into vcpu->arch.last_inst. The HEIR value has been loaded
using guest endianness, whereas the lwz will load the instruction using
host endianness. The rest of the code that uses vcpu->arch.last_inst
assumes it was loaded using host endianness.
To fix this, we define a new vcpu field to store the HEIR value. Then,
in kvmppc_handle_exit_hv(), we transfer the value from this new field to
vcpu->arch.last_inst, doing a byte-swap if the guest and host endianness
differ.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This removes the code that was added to enable HV KVM to work
on PPC970 processors. The PPC970 is an old CPU that doesn't
support virtualizing guest memory. Removing PPC970 support also
lets us remove the code for allocating and managing contiguous
real-mode areas, the code for the !kvm->arch.using_mmu_notifiers
case, the code for pinning pages of guest memory when first
accessed and keeping track of which pages have been pinned, and
the code for handling H_ENTER hypercalls in virtual mode.
Book3S HV KVM is now supported only on POWER7 and POWER8 processors.
The KVM_CAP_PPC_RMA capability now always returns 0.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Winkle is a deep idle state supported in power8 chips. A core enters
winkle when all the threads of the core enter winkle. In this state
power supply to the entire chiplet i.e core, private L2 and private L3
is turned off. As a result it gives higher powersavings compared to
sleep.
But entering winkle results in a total hypervisor state loss. Hence the
hypervisor context has to be preserved before entering winkle and
restored upon wake up.
Power-on Reset Engine (PORE) is a dedicated engine which is responsible
for powering on the chiplet during wake up. It can be programmed to
restore the register contests of a few specific registers. This patch
uses PORE to restore register state wherever possible and uses stack to
save and restore rest of the necessary registers.
With hypervisor state restore things fall under three categories-
per-core state, per-subcore state and per-thread state. To manage this,
extend the infrastructure introduced for sleep. Mainly we add a paca
variable subcore_sibling_mask. Using this and the core_idle_state we can
distingush first thread in core and subcore.
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Deep idle states like sleep and winkle are per core idle states. A core
enters these states only when all the threads enter either the
particular idle state or a deeper one. There are tasks like fastsleep
hardware bug workaround and hypervisor core state save which have to be
done only by the last thread of the core entering deep idle state and
similarly tasks like timebase resync, hypervisor core register restore
that have to be done only by the first thread waking up from these
state.
The current idle state management does not have a way to distinguish the
first/last thread of the core waking/entering idle states. Tasks like
timebase resync are done for all the threads. This is not only is
suboptimal, but can cause functionality issues when subcores and kvm is
involved.
This patch adds the necessary infrastructure to track idle states of
threads in a per-core structure. It uses this info to perform tasks like
fastsleep workaround and timebase resync only once per core.
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Originally-by: Preeti U. Murthy <preeti@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: linux-pm@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently, when going idle, we set the flag indicating that we are in
nap mode (paca->kvm_hstate.hwthread_state) and then execute the nap
(or sleep or rvwinkle) instruction, all with the MMU on. This is bad
for two reasons: (a) the architecture specifies that those instructions
must be executed with the MMU off, and in fact with only the SF, HV, ME
and possibly RI bits set, and (b) this introduces a race, because as
soon as we set the flag, another thread can switch the MMU to a guest
context. If the race is lost, this thread will typically start looping
on relocation-on ISIs at 0xc...4400.
This fixes it by setting the MSR as required by the architecture before
setting the flag or executing the nap/sleep/rvwinkle instruction.
Cc: stable@vger.kernel.org
[ shreyas@linux.vnet.ibm.com: Edited to handle LE ]
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Some nice cleanups like removing bootmem, and removal of __get_cpu_var().
There is one patch to mm/gup.c. This is the generic GUP implementation, but is
only used by us and arm(64). We have an ack from Steve Capper, and although we
didn't get an ack from Andrew he told us to take the patch through the powerpc
tree.
There's one cxl patch. This is in drivers/misc, but Greg said he was happy for
us to manage fixes for it.
There is an infrastructure patch to support an IPMI driver for OPAL. That patch
also appears in Corey Minyard's IPMI tree, you may see a conflict there.
There is also an RTC driver for OPAL. We weren't able to get any response from
the RTC maintainer, Alessandro Zummo, so in the end we just merged the driver.
The usual batch of Freescale updates from Scott.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jvyT
-----END PGP SIGNATURE-----
Merge tag 'powerpc-3.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc updates from Michael Ellerman:
"Some nice cleanups like removing bootmem, and removal of
__get_cpu_var().
There is one patch to mm/gup.c. This is the generic GUP
implementation, but is only used by us and arm(64). We have an ack
from Steve Capper, and although we didn't get an ack from Andrew he
told us to take the patch through the powerpc tree.
There's one cxl patch. This is in drivers/misc, but Greg said he was
happy for us to manage fixes for it.
There is an infrastructure patch to support an IPMI driver for OPAL.
There is also an RTC driver for OPAL. We weren't able to get any
response from the RTC maintainer, Alessandro Zummo, so in the end we
just merged the driver.
The usual batch of Freescale updates from Scott"
* tag 'powerpc-3.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (101 commits)
powerpc/powernv: Return to cpu offline loop when finished in KVM guest
powerpc/book3s: Fix partial invalidation of TLBs in MCE code.
powerpc/mm: don't do tlbie for updatepp request with NO HPTE fault
powerpc/xmon: Cleanup the breakpoint flags
powerpc/xmon: Enable HW instruction breakpoint on POWER8
powerpc/mm/thp: Use tlbiel if possible
powerpc/mm/thp: Remove code duplication
powerpc/mm/hugetlb: Sanity check gigantic hugepage count
powerpc/oprofile: Disable pagefaults during user stack read
powerpc/mm: Check for matching hpte without taking hpte lock
powerpc: Drop useless warning in eeh_init()
powerpc/powernv: Cleanup unused MCE definitions/declarations.
powerpc/eeh: Dump PHB diag-data early
powerpc/eeh: Recover EEH error on ownership change for BCM5719
powerpc/eeh: Set EEH_PE_RESET on PE reset
powerpc/eeh: Refactor eeh_reset_pe()
powerpc: Remove more traces of bootmem
powerpc/pseries: Initialise nvram_pstore_info's buf_lock
cxl: Name interrupts in /proc/interrupt
cxl: Return error to PSL if IRQ demultiplexing fails & print clearer warning
...
to the trace_seq code. It also removed the return values to the
trace_seq_*() functions and use trace_seq_has_overflowed() to see if
the buffer filled up or not. This is similar to work being done to the
seq_file code as well in another tree.
Some of the other goodies include:
o Added some "!" (NOT) logic to the tracing filter.
o Fixed the frame pointer logic to the x86_64 mcount trampolines
o Added the logic for dynamic trampolines on !CONFIG_PREEMPT systems.
That is, the ftrace trampoline can be dynamically allocated
and be called directly by functions that only have a single hook
to them.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUhbLGAAoJEEjnJuOKh9ldRV4H/3NcLbgGB2iu96la1zdYE6pG
Q7cDJMxXK80YIIL70h9G0IItcD4t62LMb72lfBnMGRj3msgFb3AgISW57EuI0Pxk
xk24wuIPoTG2S7v9sc3SboNFwO8qbtIjxD2OBmqIUrGo2sZIiGjyj3gX7mCY3uzL
WB2bUOSFz/22OgaANinR5EELHA3pZZCf54Vz1K9ndmtK0xp0j1a7xJShD6TrMdYv
mZ3zH5ViIhW4A3mdcMceh6fy2JLQAiEKF0uPTvcMMz7NlVul0mxyL/+10P7AE/3R
Ehw4fzmm4NDshPDtBOkKH0LsppgXzuItFuQUTpact3JlqTg++bV6onSsrkt1hlY=
=Z7Cm
-----END PGP SIGNATURE-----
Merge tag 'trace-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"There was a lot of clean ups and minor fixes. One of those clean ups
was to the trace_seq code. It also removed the return values to the
trace_seq_*() functions and use trace_seq_has_overflowed() to see if
the buffer filled up or not. This is similar to work being done to
the seq_file code as well in another tree.
Some of the other goodies include:
- Added some "!" (NOT) logic to the tracing filter.
- Fixed the frame pointer logic to the x86_64 mcount trampolines
- Added the logic for dynamic trampolines on !CONFIG_PREEMPT systems.
That is, the ftrace trampoline can be dynamically allocated and be
called directly by functions that only have a single hook to them"
* tag 'trace-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (55 commits)
tracing: Truncated output is better than nothing
tracing: Add additional marks to signal very large time deltas
Documentation: describe trace_buf_size parameter more accurately
tracing: Allow NOT to filter AND and OR clauses
tracing: Add NOT to filtering logic
ftrace/fgraph/x86: Have prepare_ftrace_return() take ip as first parameter
ftrace/x86: Get rid of ftrace_caller_setup
ftrace/x86: Have save_mcount_regs macro also save stack frames if needed
ftrace/x86: Add macro MCOUNT_REG_SIZE for amount of stack used to save mcount regs
ftrace/x86: Simplify save_mcount_regs on getting RIP
ftrace/x86: Have save_mcount_regs store RIP in %rdi for first parameter
ftrace/x86: Rename MCOUNT_SAVE_FRAME and add more detailed comments
ftrace/x86: Move MCOUNT_SAVE_FRAME out of header file
ftrace/x86: Have static tracing also use ftrace_caller_setup
ftrace/x86: Have static function tracing always test for function graph
kprobes: Add IPMODIFY flag to kprobe_ftrace_ops
ftrace, kprobes: Support IPMODIFY flag to find IP modify conflict
kprobes/ftrace: Recover original IP if pre_handler doesn't change it
tracing/trivial: Fix typos and make an int into a bool
tracing: Deletion of an unnecessary check before iput()
...
These are changes for drivers that are intimately tied to some SoC
and for some reason could not get merged through the respective
subsystem maintainer tree.
The largest single change here this time around is the Tegra
iommu/memory controller driver, which gets updated to the new
iommu DT binding. More drivers like this are likely to follow
for the following merge window, but we should be able to do
those through the iommu maintainer.
Other notable changes are:
* reset controller drivers from the reset maintainer (socfpga, sti, berlin)
* fixes for the keystone navigator driver merged last time
* at91 rtc driver changes related to the at91 cleanups
* ARM perf driver changes from Will Deacon
* updates for the brcmstb_gisb driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=MwMG
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"These are changes for drivers that are intimately tied to some SoC and
for some reason could not get merged through the respective subsystem
maintainer tree.
The largest single change here this time around is the Tegra
iommu/memory controller driver, which gets updated to the new iommu DT
binding. More drivers like this are likely to follow for the
following merge window, but we should be able to do those through the
iommu maintainer.
Other notable changes are:
- reset controller drivers from the reset maintainer (socfpga, sti,
berlin)
- fixes for the keystone navigator driver merged last time
- at91 rtc driver changes related to the at91 cleanups
- ARM perf driver changes from Will Deacon
- updates for the brcmstb_gisb driver"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (53 commits)
clocksource: arch_timer: Allow the device tree to specify uninitialized timer registers
clocksource: arch_timer: Fix code to use physical timers when requested
memory: Add NVIDIA Tegra memory controller support
bus: brcmstb_gisb: Add register offset tables for older chips
bus: brcmstb_gisb: Look up register offsets in a table
bus: brcmstb_gisb: Introduce wrapper functions for MMIO accesses
bus: brcmstb_gisb: Make the driver buildable on MIPS
of: Add NVIDIA Tegra memory controller binding
ARM: tegra: Move AHB Kconfig to drivers/amba
amba: Add Kconfig file
clk: tegra: Implement memory-controller clock
serial: samsung: Fix serial config dependencies for exynos7
bus: brcmstb_gisb: resolve section mismatch
ARM: common: edma: edma_pm_resume may be unused
ARM: common: edma: add suspend resume hook
powerpc/iommu: Rename iommu_[un]map_sg functions
rtc: at91sam9: add DT bindings documentation
rtc: at91sam9: use clk API instead of relying on AT91_SLOW_CLOCK
ARM: at91: add clk_lookup entry for RTT devices
rtc: at91sam9: rework the Kconfig description
...
I have a busy ppc64le KVM box where guests sometimes hit the infamous
"kernel BUG at kernel/smpboot.c:134!" issue during boot:
BUG_ON(td->cpu != smp_processor_id());
Basically a per CPU hotplug thread scheduled on the wrong CPU. The oops
output confirms it:
CPU: 0
Comm: watchdog/130
The problem is that we aren't ensuring the CPU active and online bits are set
before allowing the master to continue on. The master unparks the secondary
CPUs kthreads and the scheduler looks for a CPU to run on. It calls
select_task_rq and realises the suggested CPU is not in the cpus_allowed
mask. It then ends up in select_fallback_rq, and since the active and
online bits aren't set we choose some other CPU to run on.
Cc: stable@vger.kernel.org
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When a secondary hardware thread has finished running a KVM guest, we
currently put that thread into nap mode using a nap instruction in
the KVM code. This changes the code so that instead of doing a nap
instruction directly, we instead cause the call to power7_nap() that
put the thread into nap mode to return. The reason for doing this is
to avoid having the KVM code having to know what low-power mode to
put the thread into.
In the case of a secondary thread used to run a KVM guest, the thread
will be offline from the point of view of the host kernel, and the
relevant power7_nap() call is the one in pnv_smp_cpu_disable().
In this case we don't want to clear pending IPIs in the offline loop
in that function, since that might cause us to miss the wakeup for
the next time the thread needs to run a guest. To tell whether or
not to clear the interrupt, we use the SRR1 value returned from
power7_nap(), and check if it indicates an external interrupt. We
arrange that the return from power7_nap() when we have finished running
a guest returns 0, so pending interrupts don't get flushed in that
case.
Note that it is important a secondary thread that has finished
executing in the guest, or that didn't have a guest to run, should
not return to power7_nap's caller while the kvm_hstate.hwthread_req
flag in the PACA is non-zero, because the return from power7_nap
will reenable the MMU, and the MMU might still be in guest context.
In this situation we spin at low priority in real mode waiting for
hwthread_req to become zero.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The existing MCE code calls flush_tlb hook with IS=0 (single page) resulting
in partial invalidation of TLBs which is not right. This patch fixes
that by passing IS=0xc00 to invalidate whole TLB for successful recovery
from TLB and ERAT errors.
Cc: stable@vger.kernel.org
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
upatepp can get called for a nohpte fault when we find from the linux
page table that the translation was hashed before. In that case
we are sure that there is no existing translation, hence we could
avoid doing tlbie.
We could possibly race with a parallel fault filling the TLB. But
that should be ok because updatepp is only ever relaxing permissions.
We also look at linux pte permission bits when filling hash pte
permission bits. We also hold the linux pte busy bits while
inserting/updating a hashpte entry, hence a paralle update of
linux pte is not possible. On the other hand mprotect involves
ptep_modify_prot_start which cause a hpte invalidate and not updatepp.
Performance number:
We use randbox_access_bench written by Anton.
Kernel with THP disabled and smaller hash page table size.
86.60% random_access_b [kernel.kallsyms] [k] .native_hpte_updatepp
2.10% random_access_b random_access_bench [.] doit
1.99% random_access_b [kernel.kallsyms] [k] .do_raw_spin_lock
1.85% random_access_b [kernel.kallsyms] [k] .native_hpte_insert
1.26% random_access_b [kernel.kallsyms] [k] .native_flush_hash_range
1.18% random_access_b [kernel.kallsyms] [k] .__delay
0.69% random_access_b [kernel.kallsyms] [k] .native_hpte_remove
0.37% random_access_b [kernel.kallsyms] [k] .clear_user_page
0.34% random_access_b [kernel.kallsyms] [k] .__hash_page_64K
0.32% random_access_b [kernel.kallsyms] [k] fast_exception_return
0.30% random_access_b [kernel.kallsyms] [k] .hash_page_mm
With Fix:
27.54% random_access_b random_access_bench [.] doit
22.90% random_access_b [kernel.kallsyms] [k] .native_hpte_insert
5.76% random_access_b [kernel.kallsyms] [k] .native_hpte_remove
5.20% random_access_b [kernel.kallsyms] [k] fast_exception_return
5.12% random_access_b [kernel.kallsyms] [k] .__hash_page_64K
4.80% random_access_b [kernel.kallsyms] [k] .hash_page_mm
3.31% random_access_b [kernel.kallsyms] [k] data_access_common
1.84% random_access_b [kernel.kallsyms] [k] .trace_hardirqs_on_caller
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This is what we get in dmesg when booting a pseries guest and
the hypervisor doesn't provide EEH support.
[ 0.166655] EEH functionality not supported
[ 0.166778] eeh_init: Failed to call platform init function (-22)
Since both powernv_eeh_init() and pseries_eeh_init() already complain when
hitting an error, it is not needed to print more (especially such an
uninformative message).
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cleanup OpalMCE_* definitions/declarations and other related code which
is not used anymore.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Acked-by: Benjamin Herrrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On PowerNV platform, PHB diag-data is dumped after stopping device
drivers. In case of recursive EEH errors, the kernel is usually
crashed before dumping PHB diag-data for the second EEH error. It's
hard to locate the root cause of the second EEH error without PHB
diag-data.
The patch adds one more EEH option "eeh=early_log", which helps
dumping PHB diag-data immediately once frozen PE is detected, in
order to get the PHB diag-data for the second EEH error.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In PCI passthrou scenario, we need simulate EEH recovery for Emulex
adapters when their ownership changes, as we did in commit 5cfb20b96
("powerpc/eeh: Emulate EEH recovery for VFIO devices"). Broadcom
BCM5719 adpaters are facing same problem and needs same cure.
Reported-by: Rajeshkumar Subramanian <rajeshkumars@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch introduces additional flag EEH_PE_RESET to indicate the
corresponding PE is under reset. In turn, the PE retrieval bakcend
on PowerNV platform can return unfrozen state for the EEH core to
moving forward. Flag EEH_PE_CFG_BLOCKED isn't the correct one for
the purpose.
In PCI passthrou case, the problem is more worse: Guest doesn't
recover 6th EEH error. The PE is left in isolated (frozen) and
config blocked state on Broadcom adapters. We can't retrieve the
PE's state correctly any more, even from the host side via sysfs
/sys/bus/pci/devices/xxx/eeh_pe_state.
Reported-by: Rajeshkumar Subramanian <rajeshkumars@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch refactors eeh_reset_pe() in order for:
* Varied return values for different failure cases.
* Replace pr_err() with pr_warn() and print function name.
* Coding style cleanup.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull powerpc fixes from Michael Ellerman:
"Here are five fixes for you to pull please.
They're all CC'ed to stable except the "Fix PE state format" one which
went in this release"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
powerpc: 32 bit getcpu VDSO function uses 64 bit instructions
powerpc/powernv: Replace OPAL_DEASSERT_RESET with EEH_RESET_DEACTIVATE
powerpc/eeh: Fix PE state format
powerpc/pseries: Fix endiannes issue in RTAS call from xmon
powerpc/powernv: Fix the hmi event version check.
I used some 64 bit instructions when adding the 32 bit getcpu VDSO
function. Fix it.
Fixes: 18ad51dd34 ("powerpc: Add VDSO version of getcpu")
Cc: stable@vger.kernel.org
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Obviously I had wrong format given to the PE state output from
/sys/bus/pci/devices/xxxx/eeh_pe_state with some typoes, which
was introduced by commit 2013add4ce. The patch fixes it up.
Fixes: 2013add4ce ("powerpc/eeh: Show hex prefix for PE state sysfs")
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This is now fully replaced with the generic "no_64bit_msi" one
that is set by the respective drivers directly.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Although we are now selecting NO_BOOTMEM, we still have some traces of
bootmem lying around. That is because even with NO_BOOTMEM there is
still a shim that converts bootmem calls into memblock calls, but
ultimately we want to remove all traces of bootmem.
Most of the patch is conversions from alloc_bootmem() to
memblock_virt_alloc(). In general a call such as:
p = (struct foo *)alloc_bootmem(x);
Becomes:
p = memblock_virt_alloc(x, 0);
We don't need the cast because memblock_virt_alloc() returns a void *.
The alignment value of zero tells memblock to use the default alignment,
which is SMP_CACHE_BYTES, the same value alloc_bootmem() uses.
We remove a number of NULL checks on the result of
memblock_virt_alloc(). That is because memblock_virt_alloc() will panic
if it can't allocate, in exactly the same way as alloc_bootmem(), so the
NULL checks are and always have been redundant.
The memory returned by memblock_virt_alloc() is already zeroed, so we
remove several memsets of the result of memblock_virt_alloc().
Finally we convert a few uses of __alloc_bootmem(x, y, MAX_DMA_ADDRESS)
to just plain memblock_virt_alloc(). We don't use memblock_alloc_base()
because MAX_DMA_ADDRESS is ~0ul on powerpc, so limiting the allocation
to that is pointless, 16XB ought to be enough for anyone.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The IOMMU-API gained support for a new iommu_map_sg
function. This causes compile failures on powerpc because
the function name is already globally used there.
This patch renames adds a ppc_ prefix to these functions to
solve the compile problem.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Scott says:
"Highlights include a bunch of 8xx optimizations, device tree bindings
for Freescale BMan, QMan, and FMan datapath components, misc device tree
updates, and inbound rio window support."
The patch implements the OPAL rtc driver that binds with the rtc
driver subsystem. The driver uses the platform device infrastructure
to probe the rtc device and register it to rtc class framework. The
'wakeup' is supported depending upon the property 'has-tpo' present
in the OF node. It provides a way to load the generic rtc driver in
in the absence of an OPAL driver.
The patch also moves the existing OPAL rtc get/set time interfaces to the
new driver and exposes the necessary OPAL calls using EXPORT_SYMBOL_GPL.
Test results:
-------------
Host:
[root@tul169p1 ~]# ls -l /sys/class/rtc/
total 0
lrwxrwxrwx 1 root root 0 Oct 14 03:07 rtc0 -> ../../devices/opal-rtc/rtc/rtc0
[root@tul169p1 ~]# cat /sys/devices/opal-rtc/rtc/rtc0/time
08:10:07
[root@tul169p1 ~]# echo `date '+%s' -d '+ 2 minutes'` > /sys/class/rtc/rtc0/wakealarm
[root@tul169p1 ~]# cat /sys/class/rtc/rtc0/wakealarm
1413274345
[root@tul169p1 ~]#
FSP:
$ smgr mfgState
standby
$ rtim timeofday
System time is valid: 2014/10/14 08:12:04.225115
$ smgr mfgState
ipling
$
CC: devicetree@vger.kernel.org
CC: tglx@linutronix.de
CC: rtc-linux@googlegroups.com
CC: a.zummo@towertech.it
Signed-off-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Back in 2009 we merged 501cb16d3c "Randomise PIEs", which added support for
randomizing PIE (Position Independent Executable) binaries.
That commit added randomize_et_dyn(), which correctly randomized the addresses,
but failed to honor PF_RANDOMIZE. That means it was not possible to disable PIE
randomization via the personality flag, or /proc/sys/kernel/randomize_va_space.
Since then there has been generic support for PIE randomization added to
binfmt_elf.c, selectable via ARCH_BINFMT_ELF_RANDOMIZE_PIE.
Enabling that allows us to drop randomize_et_dyn(), which means we start
honoring PF_RANDOMIZE correctly.
It also causes a fairly major change to how we layout PIE binaries.
Currently we will place the binary at 512MB-520MB for 32 bit binaries, or
512MB-1.5GB for 64 bit binaries, eg:
$ cat /proc/$$/maps
4e550000-4e580000 r-xp 00000000 08:02 129813 /bin/dash
4e580000-4e590000 rw-p 00020000 08:02 129813 /bin/dash
10014110000-10014140000 rw-p 00000000 00:00 0 [heap]
3fffaa3f0000-3fffaa5a0000 r-xp 00000000 08:02 921 /lib/powerpc64le-linux-gnu/libc-2.19.so
3fffaa5a0000-3fffaa5b0000 rw-p 001a0000 08:02 921 /lib/powerpc64le-linux-gnu/libc-2.19.so
3fffaa5c0000-3fffaa5d0000 rw-p 00000000 00:00 0
3fffaa5d0000-3fffaa5f0000 r-xp 00000000 00:00 0 [vdso]
3fffaa5f0000-3fffaa620000 r-xp 00000000 08:02 1246 /lib/powerpc64le-linux-gnu/ld-2.19.so
3fffaa620000-3fffaa630000 rw-p 00020000 08:02 1246 /lib/powerpc64le-linux-gnu/ld-2.19.so
3ffffc340000-3ffffc370000 rw-p 00000000 00:00 0 [stack]
With this commit applied we don't do any special randomisation for the binary,
and instead rely on mmap randomisation. This means the binary ends up at high
addresses, eg:
$ cat /proc/$$/maps
3fff99820000-3fff999d0000 r-xp 00000000 08:02 921 /lib/powerpc64le-linux-gnu/libc-2.19.so
3fff999d0000-3fff999e0000 rw-p 001a0000 08:02 921 /lib/powerpc64le-linux-gnu/libc-2.19.so
3fff999f0000-3fff99a00000 rw-p 00000000 00:00 0
3fff99a00000-3fff99a20000 r-xp 00000000 00:00 0 [vdso]
3fff99a20000-3fff99a50000 r-xp 00000000 08:02 1246 /lib/powerpc64le-linux-gnu/ld-2.19.so
3fff99a50000-3fff99a60000 rw-p 00020000 08:02 1246 /lib/powerpc64le-linux-gnu/ld-2.19.so
3fff99a60000-3fff99a90000 r-xp 00000000 08:02 129813 /bin/dash
3fff99a90000-3fff99aa0000 rw-p 00020000 08:02 129813 /bin/dash
3fffc3de0000-3fffc3e10000 rw-p 00000000 00:00 0 [stack]
3fffc55e0000-3fffc5610000 rw-p 00000000 00:00 0 [heap]
Although this should be OK, it's possible it might break badly written
binaries that make assumptions about the address space layout.
Signed-off-by: Vineeth Vijayan <vvijayan@mvista.com>
[mpe: Rewrite changelog]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Firmware is allowed to communicate to us via the "ibm,pa-features" property
that TM (Transactional Memory) support is disabled.
Currently this doesn't happen on any platform we're aware of, but we should
honor it anyway.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The system call FLIH (first-level interrupt handler) at 0xc00
unconditionally sets hardware priority to medium. For hypercalls, this
means we lose guest OS priority. The front end (do_kvm_0x**) to the
KVM interrupt handler always assumes that PPR priority is saved in
PACA exception save area, so it copies this to the kvm_hstate
structure. For hypercalls, this would be the saved priority from any
previous exception. Eventually, the guest gets resumed with an
incorrect priority.
The fix is to save the PPR priority in PACA exception save area before
switching HMT priorities in the FLIH so that existing code described above
in the KVM interrupt handler can copy it from there into the VCPU's saved
context.
Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
[mpe: Dropped HMT_MEDIUM_PPR_DISCARD and reworded comment]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We have some code in udbg_uart_getc_poll() that tries to protect
against a NULL udbg_uart_in, but gets it all wrong.
Found with the LLVM static analyzer (scan-build).
Fixes: 309257484c ("powerpc: Cleanup udbg_16550 and add support for LPC PIO-only UARTs")
Signed-off-by: Anton Blanchard <anton@samba.org>
[mpe: Add some newlines for readability while we're here]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With the introduction of the dynamic trampolines, it is useful that if
things go wrong that ftrace_bug() produces more information about what
the current state is. This can help debug issues that may arise.
Ftrace has lots of checks to make sure that the state of the system it
touchs is exactly what it expects it to be. When it detects an abnormality
it calls ftrace_bug() and disables itself to prevent any further damage.
It is crucial that ftrace_bug() produces sufficient information that
can be used to debug the situation.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Borislav Petkov <bp@suse.de>
Tested-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Looks like I introduced this when adding LE support.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The build is broken with CONFIG_PPC32=y, CONFIG_FB_VGA16=y and
CONFIG_VGA_CONSOLE=n.
The problem is that vgacon_remap_base is not defined. It's used in:
#define VGA_MAP_MEM(x,s) (x + vgacon_remap_base)
Which is used in the vga16fb.c code.
Digging down it seems vgacon_remap_base is never initialised. It used to
be, back in arch/ppc (pplus.c and prep_setup.c), but none of that code
ever made it to arch/powerpc.
So given it's been unused for >6 years, remove it.
Whether vga16fb.c works on 32-bit is another question, but this patch
shouldn't affect it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
CONFIG_MCOUNT is not defined anymore, the corresponding #ifdef there
is CONFIG_FUNCTION_TRACER.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Instead of passing in the stack address of the link register
to be modified, just pass in the old value and return the
new value and rely on ftrace_graph_caller to do the
modification.
This removes the exception handling around the stack update -
it isn't needed and we weren't consistent about it. Later on
we would do an unprotected modification:
if (!ftrace_graph_entry(&trace)) {
*parent = old;
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
mod_return_to_handler is the same as return_to_handler, except
it handles the change of the TOC (r2). Add this into
return_to_handler and remove mod_return_to_handler.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We did part of sparse initialisation in setup_arch and part in
initmem_init. Put them together.
Signed-off-by: Anton Blanchard <anton@samba.org>
Tested-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Lots of places included bootmem.h even when not using bootmem.
Signed-off-by: Anton Blanchard <anton@samba.org>
Tested-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now bootmem is gone from powerpc we can remove comments mentioning it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Tested-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
At the moment we transition from the memblock alloctor to the bootmem
allocator. Gitting rid of the bootmem allocator removes a bunch of
complicated code (most of which I owe the dubious honour of being
responsible for writing).
Signed-off-by: Anton Blanchard <anton@samba.org>
Tested-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
8xx sometimes need to load a invalid/non-present TLBs in
it DTLB asm handler.
These must be invalidated separaly as linux mm doesn't.
Commit 5efab4a02c was invalidating them in
arch/powerpc/mm/fault.c.
This patch does the invalidation earlier in order to free the TLB as soon as
possible. This also has the advantage of removing some 8xx specific code from
fault.c
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
As we are not using anymore DAR to save registers, it is now available for
saving the r3 register used for CPU6 ERRATA handling. Therefore we can
remove the major hack which was to use memory location 0 to save r3.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
There is not need to restore r10, r11 and cr registers at this end of ITLBmiss
handler as they are saved again to the same place in ITLBError handler we are
jumping to.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
When a PMD entry is valid, _PMD_PRESENT is set. Therefore, forcing that bit
during TLB loading is useless.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
No need to re-set this bit at each TLB miss. Let's set it in the PTE.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch hiddes that SPR address needed for CPU6 ERRATA handling in the macro.
Then we don't have to worry about this address directly in the code.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch activates the handling of 16k pages on the MPC8xx.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Value 0x00f0 is used to force bits in TLB level 2 entry. This value is linked
to the page size and will vary when we change the page size. Lets define a const
for it in order to have it at only one place.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
For PAGE size related operations, use PAGE size consts in order to be able to
use different page size in the futur.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
MD_TWC can only be used properly with 4k pages.
So lets calculate level 2 table index by ourselves.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Use M_TW instead of M_TWB for storing Level 1 table address as M_TWB requires
4k aligned tables, which is only the case with 4k pages.
Consequently, we have to calculate the level 1 table index by ourselves.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
In DTLBError handler there is not need to restore r10, r11 and cr registers
after fixing DAR as they are saved again to the same place just after.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
DataAccess exception is never generated by MPC8xx so do the job directly where
it is used to avoid an unnecessary branching.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Exception InstructionAccess does not exist on MPC8xx. No need to branch there from somewhere else.
Handling can be done directly in InstructionTLBError Exception.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
ppc64_boot_msg is meant to be a boot debug aid, but
is only used in one spot. Get rid of it, and save
ourseleves a couple of lines in the kernel log
buffer.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Newer POWER designs do not implement PCI I/O space, so we
expect to see a number of these.
Reduce the severity of the warning so it doesn't mask other
real issues.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We really don't want to take a pagefault in show_instructions,
so use probe_kernel_address instead of __get_user.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The generic Linux framework to power off the machine is a function pointer
called pm_power_off. The trick about this pointer is that device drivers can
potentially implement it rather than board files.
Today on powerpc we set pm_power_off to invoke our generic full machine power
off logic which then calls ppc_md.power_off to invoke machine specific power
off.
However, when we want to add a power off GPIO via the "gpio-poweroff" driver,
this card house falls apart. That driver only registers itself if pm_power_off
is NULL to ensure it doesn't override board specific logic. However, since we
always set pm_power_off to the generic power off logic (which will just not
power off the machine if no ppc_md.power_off call is implemented), we can't
implement power off via the generic GPIO power off driver.
To fix this up, let's get rid of the ppc_md.power_off logic and just always use
pm_power_off as was intended. Then individual drivers such as the GPIO power off
driver can implement power off logic via that function pointer.
With this patch set applied and a few patches on top of QEMU that implement a
power off GPIO on the virt e500 machine, I can successfully turn off my virtual
machine after halt.
Signed-off-by: Alexander Graf <agraf@suse.de>
[mpe: Squash into one patch and update changelog based on cover letter]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This still has not been merged and now powerpc is the only arch that does
not have this change. Sorry about missing linuxppc-dev before.
V2->V2
- Fix up to work against 3.18-rc1
__get_cpu_var() is used for multiple purposes in the kernel source. One of
them is address calculation via the form &__get_cpu_var(x). This calculates
the address for the instance of the percpu variable of the current processor
based on an offset.
Other use cases are for storing and retrieving data from the current
processors percpu area. __get_cpu_var() can be used as an lvalue when
writing data or on the right side of an assignment.
__get_cpu_var() is defined as :
__get_cpu_var() always only does an address determination. However, store
and retrieve operations could use a segment prefix (or global register on
other platforms) to avoid the address calculation.
this_cpu_write() and this_cpu_read() can directly take an offset into a
percpu area and use optimized assembly code to read and write per cpu
variables.
This patch converts __get_cpu_var into either an explicit address
calculation using this_cpu_ptr() or into a use of this_cpu operations that
use the offset. Thereby address calculations are avoided and less registers
are used when code is generated.
At the end of the patch set all uses of __get_cpu_var have been removed so
the macro is removed too.
The patch set includes passes over all arches as well. Once these operations
are used throughout then specialized macros can be defined in non -x86
arches as well in order to optimize per cpu access by f.e. using a global
register that may be set to the per cpu base.
Transformations done to __get_cpu_var()
1. Determine the address of the percpu instance of the current processor.
DEFINE_PER_CPU(int, y);
int *x = &__get_cpu_var(y);
Converts to
int *x = this_cpu_ptr(&y);
2. Same as #1 but this time an array structure is involved.
DEFINE_PER_CPU(int, y[20]);
int *x = __get_cpu_var(y);
Converts to
int *x = this_cpu_ptr(y);
3. Retrieve the content of the current processors instance of a per cpu
variable.
DEFINE_PER_CPU(int, y);
int x = __get_cpu_var(y)
Converts to
int x = __this_cpu_read(y);
4. Retrieve the content of a percpu struct
DEFINE_PER_CPU(struct mystruct, y);
struct mystruct x = __get_cpu_var(y);
Converts to
memcpy(&x, this_cpu_ptr(&y), sizeof(x));
5. Assignment to a per cpu variable
DEFINE_PER_CPU(int, y)
__get_cpu_var(y) = x;
Converts to
__this_cpu_write(y, x);
6. Increment/Decrement etc of a per cpu variable
DEFINE_PER_CPU(int, y);
__get_cpu_var(y)++
Converts to
__this_cpu_inc(y)
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Paul Mackerras <paulus@samba.org>
Signed-off-by: Christoph Lameter <cl@linux.com>
[mpe: Fix build errors caused by set/or_softirq_pending(), and rework
assignment in __set_breakpoint() to use memcpy().]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Back in 7230c56441 ("powerpc: Rework lazy-interrupt handling") we
added a call out to restore_interrupts() (written in c) before calling
do_notify_resume:
bl restore_interrupts
addi r3,r1,STACK_FRAME_OVERHEAD
bl do_notify_resume
Unfortunately do_notify_resume takes two arguments, the second one
being the thread_info flags:
void do_notify_resume(struct pt_regs *regs, unsigned long thread_info_flags)
We do populate r4 (the second argument) earlier, but
restore_interrupts() is free to muck it up all it wants. My guess is
the gcc compiler gods shone down on us and its register allocator
never used r4. Sometimes, rarely, luck is on our side.
LLVM on the other hand did trample r4.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull more powerpc updates from Michael Ellerman:
"Here's some more updates for powerpc for 3.18.
They are a bit late I know, though must are actually bug fixes. In my
defence I nearly cut the top of my finger off last weekend in a
gruesome bike maintenance accident, so I spent a good part of the week
waiting around for doctors. True story, I can send photos if you like :)
Probably the most interesting fix is the sys_call_table one, which
enables syscall tracing for powerpc. There's a fix for HMI handling
for old firmware, more endian fixes for firmware interfaces, more EEH
fixes, Anton fixed our routine that gets the current stack pointer,
and a few other misc bits"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (22 commits)
powerpc: Only do dynamic DMA zone limits on platforms that need it
powerpc: sync pseries_le_defconfig with pseries_defconfig
powerpc: Add printk levels to setup_system output
powerpc/vphn: NUMA node code expects big-endian
powerpc/msi: Use WARN_ON() in msi bitmap selftests
powerpc/msi: Fix the msi bitmap alignment tests
powerpc/eeh: Block CFG upon frozen Shiner adapter
powerpc/eeh: Don't collect logs on PE with blocked config space
powerpc/eeh: Block PCI config access upon frozen PE
powerpc/pseries: Drop config requests in EEH accessors
powerpc/powernv: Drop config requests in EEH accessors
powerpc/eeh: Rename flag EEH_PE_RESET to EEH_PE_CFG_BLOCKED
powerpc/eeh: Fix condition for isolated state
powerpc/pseries: Make CPU hotplug path endian safe
powerpc/pseries: Use dump_stack instead of show_stack
powerpc: Rename __get_SP() to current_stack_pointer()
powerpc: Reimplement __get_SP() as a function not a define
powerpc/numa: Add ability to disable and debug topology updates
powerpc/numa: check error return from proc_create
powerpc/powernv: Fallback to old HMI handling behavior for old firmware
...
Pull audit updates from Eric Paris:
"So this change across a whole bunch of arches really solves one basic
problem. We want to audit when seccomp is killing a process. seccomp
hooks in before the audit syscall entry code. audit_syscall_entry
took as an argument the arch of the given syscall. Since the arch is
part of what makes a syscall number meaningful it's an important part
of the record, but it isn't available when seccomp shoots the
syscall...
For most arch's we have a better way to get the arch (syscall_get_arch)
So the solution was two fold: Implement syscall_get_arch() everywhere
there is audit which didn't have it. Use syscall_get_arch() in the
seccomp audit code. Having syscall_get_arch() everywhere meant it was
a useless flag on the stack and we could get rid of it for the typical
syscall entry.
The other changes inside the audit system aren't grand, fixed some
records that had invalid spaces. Better locking around the task comm
field. Removing some dead functions and structs. Make some things
static. Really minor stuff"
* git://git.infradead.org/users/eparis/audit: (31 commits)
audit: rename audit_log_remove_rule to disambiguate for trees
audit: cull redundancy in audit_rule_change
audit: WARN if audit_rule_change called illegally
audit: put rule existence check in canonical order
next: openrisc: Fix build
audit: get comm using lock to avoid race in string printing
audit: remove open_arg() function that is never used
audit: correct AUDIT_GET_FEATURE return message type
audit: set nlmsg_len for multicast messages.
audit: use union for audit_field values since they are mutually exclusive
audit: invalid op= values for rules
audit: use atomic_t to simplify audit_serial()
kernel/audit.c: use ARRAY_SIZE instead of sizeof/sizeof[0]
audit: reduce scope of audit_log_fcaps
audit: reduce scope of audit_net_id
audit: arm64: Remove the audit arch argument to audit_syscall_entry
arm64: audit: Add audit hook in syscall_trace_enter/exit()
audit: x86: drop arch from __audit_syscall_entry() interface
sparc: implement is_32bit_task
sparc: properly conditionalize use of TIF_32BIT
...
Scott's patch 1c98025c6c "Dynamic DMA zone limits" changed
dma_direct_alloc_coherent() to start using dev->coherent_dma_mask.
That seems fair enough, but it exposes the fact that some of the drivers
we care about on IBM platforms aren't setting the coherent mask.
The proper fix is to have drivers set the coherent mask and also have
the platform code honor it.
For now, just restrict the dynamic DMA zone limits to the platforms that
need it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Scott Wood <scottwood@freescale.com>
Commit 0b0b0893d4 "of/pci: Fix the conversion of IO ranges into IO
resources" changed the behaviour of of_pci_range_to_resource().
Previously it simply populated the resource based on the arguments. Now
it calls pci_register_io_range() and pci_address_to_pio(). These both
have two implementations depending on whether PCI_IOBASE is defined,
which it is not for powerpc.
Further complicating matters, both routines are weak, and powerpc
implements it's own version of one - pci_address_to_pio(). However
powerpc's implementation depends on other initialisations which are done
later in boot.
The end result is incorrectly initialised IO space. Often we can get
away with that, because we don't make much use of IO space. However
virtio requires it, so we see eg:
pci_bus 0000:00: root bus resource [io 0xffff] (bus address [0xffffffffffffffff-0xffffffffffffffff])
PCI: Cannot allocate resource region 0 of device 0000:00:01.0, will remap
virtio-pci 0000:00:01.0: can't enable device: BAR 0 [io size 0x0020] not assigned
The simplest fix for now is to just stop using of_pci_range_to_resource(),
and open-code the original implementation, that's all we want it to do.
Fixes: 0b0b0893d4 ("of/pci: Fix the conversion of IO ranges into IO resources")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When the PE's config space is marked as blocked, PCI config read
requests always return 0xFF's. It's pointless to collect logs in
this case.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The problem was found when I tried to inject PCI config error by
PHB3 PAPR error injection registers into Broadcom Austin 4-ports
NIC adapter. The frozen PE was reported successfully and EEH core
started to recover it. However, I run into fenced PHB when dumping
PCI config space as EEH logs. I was told that PCI config requests
should not be progagated to the adapter until PE reset is done
successfully. Otherise, we would run out of PHB internal credits
and trigger PCT (PCIE Completion Timeout), which leads to the
fenced PHB.
The patch introduces another PE flag EEH_PE_CFG_RESTRICTED, which
is set during PE initialization time if the PE includes the specific
PCI devices that need block PCI config access until PE reset is done.
When the PE becomes frozen for the first time, EEH_PE_CFG_BLOCKED is
set if the PE has flag EEH_PE_CFG_RESTRICTED. Then the PCI config
access to the PE will be dropped by platform PCI accessors until
PE reset is done successfully. The mechanism is shared by PowerNV
platform owned PE or userland owned ones. It's not used on pSeries
platform yet.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The pSeires EEH config accessors rely on rtas_{read, write}_config()
and the condition to check if the PE's config space is blocked
should be moved to those 2 functions so that config requests from
kernel, userland, EEH core can be dropped to avoid recursive EEH error
if necessary.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The flag EEH_PE_RESET indicates blocking config space of the PE
during reset time. We potentially need block PE's config space
other than reset time. So it's reasonable to replace it with
EEH_PE_CFG_BLOCKED to indicate its usage.
There are no substantial code or logic changes in this patch.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Function eeh_pe_state_mark() could possibly have combination of
multiple EEH PE state as its argument. The patch fixes the condition
used to check if EEH_PE_ISOLATED is included.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael points out that __get_SP() is a pretty horrible
function name. Let's give it a better name.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Li Zhong points out an issue with our current __get_SP()
implementation. If ftrace function tracing is enabled (ie -pg
profiling using _mcount) we spill a stack frame on 64bit all the
time.
If a function calls __get_SP() and later calls a function that is
tail call optimised, we will pop the stack frame and the value
returned by __get_SP() is no longer valid. An example from Li can
be found in save_stack_trace -> save_context_stack:
c0000000000432c0 <.save_stack_trace>:
c0000000000432c0: mflr r0
c0000000000432c4: std r0,16(r1)
c0000000000432c8: stdu r1,-128(r1) <-- stack frame for _mcount
c0000000000432cc: std r3,112(r1)
c0000000000432d0: bl <._mcount>
c0000000000432d4: nop
c0000000000432d8: mr r4,r1 <-- __get_SP()
c0000000000432dc: ld r5,632(r13)
c0000000000432e0: ld r3,112(r1)
c0000000000432e4: li r6,1
c0000000000432e8: addi r1,r1,128 <-- pop stack frame
c0000000000432ec: ld r0,16(r1)
c0000000000432f0: mtlr r0
c0000000000432f4: b <.save_context_stack> <-- tail call optimized
save_context_stack ends up with a stack pointer below the current
one, and it is likely to be scribbled over.
Fix this by making __get_SP() a function which returns the
callers stack frame. Also replace inline assembly which grabs
the stack pointer in save_stack_trace and show_stack with
__get_SP().
This also fixes an issue with perf_arch_fetch_caller_regs().
It currently unwinds the stack once, which will skip a
valid stack frame on a leaf function. With the __get_SP() fixes
in this patch, we never need to unwind the stack frame to get
to the first interesting frame.
We have to export __get_SP() because perf_arch_fetch_caller_regs()
(which is used in modules) calls it from a header file.
Reported-by: Li Zhong <zhong@linux.vnet.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull powerpc updates from Michael Ellerman:
"Here's a first pull request for powerpc updates for 3.18.
The bulk of the additions are for the "cxl" driver, for IBM's Coherent
Accelerator Processor Interface (CAPI). Most of it's in drivers/misc,
which Greg & Arnd maintain, Greg said he was happy for us to take it
through our tree.
There's the usual minor cleanups and fixes, including a bit of noise
in drivers from some of those. A bunch of updates to our EEH code,
which has been getting more testing. Several nice speedups from
Anton, including 20% in clear_page().
And a bunch of updates for freescale from Scott"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (130 commits)
cxl: Fix afu_read() not doing finish_wait() on signal or non-blocking
cxl: Add documentation for userspace APIs
cxl: Add driver to Kbuild and Makefiles
cxl: Add userspace header file
cxl: Driver code for powernv PCIe based cards for userspace access
cxl: Add base builtin support
powerpc/mm: Add hooks for cxl
powerpc/opal: Add PHB to cxl mode call
powerpc/mm: Add new hash_page_mm()
powerpc/powerpc: Add new PCIe functions for allocating cxl interrupts
cxl: Add new header for call backs and structs
powerpc/powernv: Split out set MSI IRQ chip code
powerpc/mm: Export mmu_kernel_ssize and mmu_linear_psize
powerpc/msi: Improve IRQ bitmap allocator
powerpc/cell: Make spu_flush_all_slbs() generic
powerpc/cell: Move data segment faulting code out of cell platform
powerpc/cell: Move spu_handle_mm_fault() out of cell platform
powerpc/pseries: Use new defines when calling H_SET_MODE
powerpc: Update contact info in Documentation files
powerpc/perf/hv-24x7: Simplify catalog_read()
...
In HMI interrupt handler we don't touch SRR0/SRR1, instead we touch
HSRR0/HSRR1. Hence we don't need to clear MSR_RI bit.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Merge patch-bomb from Andrew Morton:
- part of OCFS2 (review is laggy again)
- procfs
- slab
- all of MM
- zram, zbud
- various other random things: arch, filesystems.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (164 commits)
nosave: consolidate __nosave_{begin,end} in <asm/sections.h>
include/linux/screen_info.h: remove unused ORIG_* macros
kernel/sys.c: compat sysinfo syscall: fix undefined behavior
kernel/sys.c: whitespace fixes
acct: eliminate compile warning
kernel/async.c: switch to pr_foo()
include/linux/blkdev.h: use NULL instead of zero
include/linux/kernel.h: deduplicate code implementing clamp* macros
include/linux/kernel.h: rewrite min3, max3 and clamp using min and max
alpha: use Kbuild logic to include <asm-generic/sections.h>
frv: remove deprecated IRQF_DISABLED
frv: remove unused cpuinfo_frv and friends to fix future build error
zbud: avoid accessing last unused freelist
zsmalloc: simplify init_zspage free obj linking
mm/zsmalloc.c: correct comment for fullness group computation
zram: use notify_free to account all free notifications
zram: report maximum used memory
zram: zram memory size limitation
zsmalloc: change return value unit of zs_get_total_size_bytes
zsmalloc: move pages_allocated to zs_pool
...
The different architectures used their own (and different) declarations:
extern __visible const void __nosave_begin, __nosave_end;
extern const void __nosave_begin, __nosave_end;
extern long __nosave_begin, __nosave_end;
Consolidate them using the first variant in <asm/sections.h>.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Freescale updates from Scott (27 commits):
"Highlights include DMA32 zone support (SATA, USB, etc now works on 64-bit
FSL kernels), MSI changes, 8xx optimizations and cleanup, t104x board
support, and PrPMC PCI enumeration."
pci_bus_find_capability() is decleared in pci.h, so it is not necessary to do
it again.
This patch removes it.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add printk levels to some places in the powerpc port.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There is no need for yet another copy of the command line, just
use boot_command_line like everyone else.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use pr_fmt to give some context to the error messages in the
module code, and convert open coded debug printk to pr_debug.
Use pr_err for error messages.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move MSI checks from arch_msi_check_device() to arch_setup_msi_irqs().
This makes the code more compact and allows removing
arch_msi_check_device() from generic MSI code.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
As Michael suggested, the hex prefix for the output of EEH PE
state sysfs entry (/sys/bus/pci/devices/xxx/eeh_pe_state) is
always informative to users.
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The dma_get_required_mask() function is used by some drivers to
query the platform about what DMA mask is needed to cover all of
memory. This is a bit of a strange semantic when we have to choose
between IOMMU translation or bypass, but essentially what it means
is "what DMA mask will give best performances".
Currently, our IOMMU backend always returns a 32-bit mask here, we
don't do anything special to it when we have bypass available. This
causes some drivers to choose a 32-bit mask, thus losing the ability
to use the bypass window, thinking this is more efficient. The problem
was reported from the driver of following device:
0004:03:00.0 0107: 1000:0087 (rev 05)
0004:03:00.0 Serial Attached SCSI controller: LSI Logic / Symbios \
Logic SAS2308 PCI-Express Fusion-MPT SAS-2 (rev 05)
This patch adds an override of that function in order to, instead,
return a 64-bit mask whenever a bypass window is available in order
for drivers to prefer this configuration.
Reported-by: Murali N. Iyer <mniyer@us.ibm.com>
Suggested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The PEs can be organized as nested. Current implementation doesn't
dump PCI config space for subordinate devices of child PEs. However,
the frozen PE could be caused by those subordinate devices of its
child PEs.
The patch dumps PCI config space for all subordinate devices of the
problematic PE.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When enabling EEH functionality on passed through devices (PE)
with VFIO, the devices in the PE would be removed permanently
from guest side. In that case, the PE remains frozen state.
When returning PE to host, or restarting the guest again, we
had mechanism unfreezing the PE by clearing PESTA/B frozen
bits. However, that's not enough for some adapters, which are
indicated as following "lspci" shows. Those adapters require
hot reset on the parent bus to bring their firmware back to
workable state. Otherwise, those adaptrs won't be operative
and the host (for returning case) or the guest will fail to
load the drivers for those adapters without exception.
0000:01:00.0 Ethernet controller: Emulex Corporation OneConnect \
10Gb NIC (be3) (rev 02)
0000:01:00.0 0200: 19a2:0710 (rev 02)
0001:03:00.0 Ethernet controller: Emulex Corporation OneConnect \
NIC (Lancer) (rev 10)
0001:03:00.0 0200: 10df:e220 (rev 10)
The patch adds mechanism to emulate EEH recovery (for hot reset
on parent PCI bus) on 3 gates to fix the issue: open/release one
adapter of the PE, enable EEH functionality on one adapter of the
PE.
Reported-by: Murilo Fossa Vicentini <muvic@br.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PE would be owned by userland, which probably request PE reset
done in host side. During the reset, we should drop the PCI
config accesses to the PE with help of flag EEH_PE_RESET.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Function pcibios_set_pcie_reset_state() can be used to do PCI
reset. PCI config access during the reset usually causes EEH
errors unexpectedly. In order to avoid the EEH error, the patch
blocks PCI config access during reset with the help of flag
EEH_PE_RESET, which is similar to what we did in EEH PE reset
path.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The patch uses eeh_unfreeze_pe() to replace the logic clearing
frozen IO and DMA, in order to simplify the code.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When passing through PE to guest, that's possibly in frozen
state. The driver for the pass-through devices on guest side
can't be loaded successfully as reported. We already had one
gate in eeh_dev_open() to clear PE frozen state accordingly,
but that's not enough because the function is only called at
QEMU startup for once.
The patch adds another gate in eeh_pe_set_option() so that the
PE frozen state can be cleared at QEMU restart time.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The function eeh_pci_enable() is called to apply various requests
to one particular PE: Enabling EEH, Disabling EEH, Enabling IO,
Enabling DMA, Freezing PE. When enabling IO or DMA on one specific
PE, we need check that IO or DMA isn't enabled previously. But
the condition used to do the check isn't completely correct because
one PE would be in DMA frozen state with workable IO path, or vice
versa.
The patch fixes the improper condition.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The problem was reported by Carol: In the scenario of passing mlx4
adapter to guest, EEH error could be recovered successfully. When
returning the device back to host, the driver (mlx4_core.ko)
couldn't be loaded successfully because of error number -5 (-EIO)
returned from mlx4_get_ownership(), which hits offlined PCI device.
The root cause is that we missed to put the affected devices into
normal state on clearing PE isolated state right after PE reset.
The patch fixes above issue by putting the affected devices to
normal state when clearing PE isolated state in eeh_pe_state_clear().
Cc: stable@vger.kernel.org
Reported-by: Carol L. Soto <clsoto@us.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When passing through device, its PE might have been put into frozen
state. One obvious example would be: the passed PE is forced to be
offline because of hitting maximal allowed EEH errors in userland.
In that case, the frozen state won't be cleared and then the PE is
returned back to host, which might not have chance detecting and
recovering from it.
The patch adds more check when passing through device and clear the
PE frozen state if necessary.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The PCI devices that have been passed through are enabled before
reset, we need restore to the enabled state after reset. Otherwise,
MMIO access might be issued to disabled devices after reset and
causes exceptional recursive EEH error.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The patch adds one more option (EEH_OPT_FREEZE_PE) to set_option()
method to proactively freeze PE, which will be issued before resetting
pass-throughed PE to drop MMIO access during reset because it's
always contributing to recursive EEH error.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The patch adds sysfs entry "eeh_pe_state". Reading on it returns
the PE's state while writing to it clears the frozen state. It's
used to check or clear the PE frozen state from userland for
debugging purpose.
The patch also replaces printk(KERN_WARNING ...) with pr_warn() in
eeh_sysfs.c
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
eeh_check_failure() is used to check frozen state of the PE which
owns the indicated I/O address. The argument "val" of the function
isn't used. The patch drops it and return the frozen state of the
PE as expected.
Cc: Vishal Mansur <vmansur@linux.vnet.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
At boot we display a bunch of low level settings which can be useful to
know, and can help to spot bugs when things are fundamentally
misconfigured.
At the moment they are very widely spaced, so that we can accommodate
the line:
ppc64_caches.dcache_line_size = 0xYY
But we only print that line when the cache line size is not 128, ie.
almost never, so it just makes the display look odd usually.
The ppc64_caches prefix is redundant so remove it, which means we can
align things a bit closer for the common case. While we're there
replace the last use of camelCase (physicalMemorySize), and use
phys_mem_size.
Before:
Starting Linux PPC64 #104 SMP Wed Aug 6 18:41:34 EST 2014
-----------------------------------------------------
ppc64_pft_size = 0x1a
physicalMemorySize = 0x200000000
ppc64_caches.dcache_line_size = 0xf0
ppc64_caches.icache_line_size = 0xf0
htab_address = 0xdeadbeef
htab_hash_mask = 0x7ffff
physical_start = 0xf000bar
-----------------------------------------------------
After:
Starting Linux PPC64 #103 SMP Wed Aug 6 18:38:04 EST 2014
-----------------------------------------------------
ppc64_pft_size = 0x1a
phys_mem_size = 0x200000000
dcache_line_size = 0xf0
icache_line_size = 0xf0
htab_address = 0xdeadbeef
htab_hash_mask = 0x7ffff
physical_start = 0xf000bar
-----------------------------------------------------
This patch is final, no bike shedding ;)
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As Nish suggested, it makes more sense to init the numa node informatiion
for present cpus at boottime, which could also avoid WARN_ON(1) in
numa_setup_cpu().
With this change, we also need to change the smp_prepare_cpus() to set up
numa information only on present cpus.
For those possible, but not present cpus, their numa information
will be set up after they are started, as the original code did before commit
2fabf084b6.
Cc: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Acked-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Tested-by: Cyril Bur <cyril.bur@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit e6a6928c3e "of/fdt: Convert FDT functions to use libfdt",
the kernel stopped supporting old flat device tree formats. The minimum
supported version is now 0x10.
There was a checking function added, early_init_dt_verify(), but it's
not called on powerpc.
The result is, if you boot with an old flat device tree, the kernel will
fail to parse it correctly, think you have no memory etc. and hilarity
ensues.
We can't really fix it, but we can at least catch the fact that the
device tree is in an unsupported format and panic(). We can't call
BUG(), it's too early.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On PowerNV platforms, when a CPU is offline, we put it into nap mode.
It's possible that the CPU wakes up from nap mode while it is still
offline due to a stray IPI. A misdirected device interrupt could also
potentially cause it to wake up. In that circumstance, we need to clear
the interrupt so that the CPU can go back to nap mode.
In the past the clearing of the interrupt was accomplished by briefly
enabling interrupts and allowing the normal interrupt handling code
(do_IRQ() etc.) to handle the interrupt. This has the problem that
this code calls irq_enter() and irq_exit(), which call functions such
as account_system_vtime() which use RCU internally. Use of RCU is not
permitted on offline CPUs and will trigger errors if RCU checking is
enabled.
To avoid calling into any generic code which might use RCU, we adopt
a different method of clearing interrupts on offline CPUs. Since we
are on the PowerNV platform, we know that the system interrupt
controller is a XICS being driven directly (i.e. not via hcalls) by
the kernel. Hence this adds a new icp_native_flush_interrupt()
function to the native-mode XICS driver and arranges to call that
when an offline CPU is woken from nap. This new function reads the
interrupt from the XICS. If it is an IPI, it clears the IPI; if it
is a device interrupt, it prints a warning and disables the source.
Then it does the end-of-interrupt processing for the interrupt.
The other thing that briefly enabling interrupts did was to check and
clear the irq_happened flag in this CPU's PACA. Therefore, after
flushing the interrupt from the XICS, we also clear all bits except
the PACA_IRQ_HARD_DIS (interrupts are hard disabled) bit from the
irq_happened flag. The PACA_IRQ_HARD_DIS flag is set by power7_nap()
and is left set to indicate that interrupts are hard disabled. This
means we then have to ignore that flag in power7_nap(), which is
reasonable since it doesn't indicate that any interrupt event needs
servicing.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
of_device_ids (i.e. compatible strings and the respective data) are not
supposed to change at runtime. All functions working with of_device_ids
provided by <linux/of.h> work with const of_device_ids. This allows to
mark all struct of_device_id const, too.
While touching these line also put the __init annotation at the right
position where necessary.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fix a number of places where global functions were not including
their prototype. This ensures the prototype and the function match.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Simplify things considerably by moving all the ppc32 specific
symbol exports into its own file.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move the lib symbol exports closer to their function definitions
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Book3E specification defines shared interrupt numbers for SPE and AltiVec
units. Still SPE is present in e200/e500v2 cores while AltiVec is present in
e6500 core. So we can currently decide at compile-time which unit to support
exclusively. As Alexander Graf suggested, this will improve code readability
especially in KVM.
Use distinct defines to identify SPE/AltiVec interrupt numbers, reverting
c58ce397 and 6b310fc5 patches that added common defines.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
SPE exception handlers are now defined for 32-bit e500mc cores even though
SPE unit is not present and CONFIG_SPE is undefined.
Restrict SPE exception handlers to e200/e500 cores adding CONFIG_SPE_POSSIBLE
and consequently guard __stup_ivors and __setup_cpu functions.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Branching takes two cycles on MPC8xx. Lets duplicate the two instructions
and avoid the branching.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
By XORing the upper part of the instruction code, we get a value that can
directly be verified with the second test and we can remove the first test.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
r10 and r3 are only used inside FixupDAR function. So lets save them inside
that function only.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Since commit 2321f33790, dirty handling is not
handled here anymore. So we fix the comment.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Since commit 2321f33790, r10 is not used anymore
after FixupDAR. There is therefore no need to set it up with the value of DAR.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
SCRATCH0 and SCRATCH1 are only used in Exceptions prologs where no other
exception can happen. There is therefore no need to preserve them accross
TLB handlers, we can use them there as in other exceptions. One of the
advantages is that they do not suffer CPU6 errata unlike M_TW register.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Since commit 469d62be92, SPRG2 is used as a
scratch register just like SPRG0 and SPRG1. So Declare it as such and fix
the comment which is not valid anymore since that commit.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
A DMA zone is still needed with swiotlb, for coherent allocations.
This doesn't affect platforms that don't use swiotlb or that don't call
swiotlb_detect_4g().
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
FSL PCI cannot directly address the whole lower 4 GiB due to
conflicts with PCICSRBAR and outbound windows, and thus
max_direct_dma_addr is less than 4GiB. Honor that limit in
dma_direct_alloc_coherent().
Note that setting the DMA mask to 31 bits is not an option, since many
PCI drivers would fail if we reject 32-bit DMA in dma_supported(), and
we have no control over the setting of coherent_dma_mask if
dma_supported() returns true.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Platform code can call limit_zone_pfn() to set appropriate limits
for ZONE_DMA and ZONE_DMA32, and dma_direct_alloc_coherent() will
select a suitable zone based on a device's mask and the pfn limits that
platform code has configured.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Pull more powerpc updates from Ben Herrenschmidt:
"Here are some more powerpc bits for 3.17, essentially fixes.
The biggest series, also aimed at -stable, is from Aneesh and is the
result of weeks and weeks of debugging to find out why the heck or THP
implementation was occasionally triggering multi-hit errors in our
level 1 TLB. It ended up being a combination of issues including
subtleties as to how we should invalidate those special 'MPSS' pages
we use to allow the use of 16M pages inside 4K/64K "base page size"
segments (you really have to love our MMU !)
Another interesting one in the "OMG" category is the series from
Michael adding memory barriers to spin_is_locked(). That's also the
result of many days of debugging to figure out why the semaphore code
would occasionally crash in ways that made no sense. It ended up
being some creative lock stacking that was defeated by the fact that
our locks allow a load inside the locked section to be re-ordered with
the load of the lock value itself (I'm still of two mind about whether
to kill that once and for all by putting a heavier barrier back into
our lock implementation...). The fixes come with a long explanation
in the cset comments, feel free to read it if you feel like having a
headache today"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (25 commits)
powerpc/thp: Add tracepoints to track hugepage invalidate
powerpc/mm: Use read barrier when creating real_pte
powerpc/thp: Use ACCESS_ONCE when loading pmdp
powerpc/thp: Invalidate with vpn in loop
powerpc/thp: Handle combo pages in invalidate
powerpc/thp: Invalidate old 64K based hash page mapping before insert of 4k pte
powerpc/thp: Don't recompute vsid and ssize in loop on invalidate
powerpc/thp: Add write barrier after updating the valid bit
powerpc: reorder per-cpu NUMA information's initialization
powerpc/perf/hv-24x7: Use kmem_cache_free
powerpc/pseries/hvcserver: Fix endian issue in hvcs_get_partner_info
powerpc: Hard disable interrupts in xmon
powerpc: remove duplicate definition of TEXASR_FS
powerpc/pseries: Avoid deadlock on removing ddw
powerpc/pseries: Failure on removing device node
powerpc/boot: Use correct zlib types for comparison
powerpc/powernv: Interface to register/unregister opal dump region
printk: Add function to return log buffer address and size
powerpc: Add POWER8 features to CPU_FTRS_POSSIBLE/ALWAYS
powerpc/ppc476: Disable BTAC
...
window:
Group changes to the device tree. In preparation for adding device tree
overlay support, OF_DYNAMIC is reworked so that a set of device tree
changes can be prepared and applied to the tree all at once. OF_RECONFIG
notifiers see the most significant change here so that users always get
a consistent view of the tree. Notifiers generation is moved from before
a change to after it, and notifiers for a group of changes are emitted
after the entire block of changes have been applied
Automatic console selection from DT. Console drivers can now use
of_console_check() to see if the device node is specified as a console
device. If so then it gets added as a preferred console. UART devices
get this support automatically when uart_add_one_port() is called.
DT unit tests no longer depend on pre-loaded data in the device tree.
Data is loaded dynamically at the start of unit tests, and then unloaded
again when the tests have completed.
Also contains a few bugfixes for reserved regions and early memory setup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8IFz
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux
Pull device tree updates from Grant Likely:
"The branch contains the following device tree changes the v3.17 merge
window:
Group changes to the device tree. In preparation for adding device
tree overlay support, OF_DYNAMIC is reworked so that a set of device
tree changes can be prepared and applied to the tree all at once.
OF_RECONFIG notifiers see the most significant change here so that
users always get a consistent view of the tree. Notifiers generation
is moved from before a change to after it, and notifiers for a group
of changes are emitted after the entire block of changes have been
applied
Automatic console selection from DT. Console drivers can now use
of_console_check() to see if the device node is specified as a console
device. If so then it gets added as a preferred console. UART
devices get this support automatically when uart_add_one_port() is
called.
DT unit tests no longer depend on pre-loaded data in the device tree.
Data is loaded dynamically at the start of unit tests, and then
unloaded again when the tests have completed.
Also contains a few bugfixes for reserved regions and early memory
setup"
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux: (21 commits)
of: Fixing OF Selftest build error
drivers: of: add automated assignment of reserved regions to client devices
of: Use proper types for checking memory overflow
of: typo fix in __of_prop_dup()
Adding selftest testdata dynamically into live tree
of: Add todo tasklist for Devicetree
of: Transactional DT support.
of: Reorder device tree changes and notifiers
of: Move dynamic node fixups out of powerpc and into common code
of: Make sure attached nodes don't carry along extra children
of: Make devicetree sysfs update functions consistent.
of: Create unlocked versions of node and property add/remove functions
OF: Utility helper functions for dynamic nodes
of: Move CONFIG_OF_DYNAMIC code into a separate file
of: rename of_aliases_mutex to just of_mutex
of/platform: Fix of_platform_device_destroy iteration of devices
of: Migrate of_find_node_by_name() users to for_each_node_by_name()
tty: Update hypervisor tty drivers to use core stdout parsing code.
arm/versatile: Add the uart as the stdout device.
of: Enable console on serial ports specified by /chosen/stdout-path
...
There is an issue currently where NUMA information is used on powerpc
(and possibly ia64) before it has been read from the device-tree, which
leads to large slab consumption with CONFIG_SLUB and memoryless nodes.
NUMA powerpc non-boot CPU's cpu_to_node/cpu_to_mem is only accurate
after start_secondary(), similar to ia64, which is invoked via
smp_init().
Commit 6ee0578b4d ("workqueue: mark init_workqueues() as
early_initcall()") made init_workqueues() be invoked via
do_pre_smp_initcalls(), which is obviously before the secondary
processors are online.
Additionally, the following commits changed init_workqueues() to use
cpu_to_node to determine the node to use for kthread_create_on_node:
bce903809a ("workqueue: add wq_numa_tbl_len and
wq_numa_possible_cpumask[]")
f3f90ad469 ("workqueue: determine NUMA node of workers accourding to
the allowed cpumask")
Therefore, when init_workqueues() runs, it sees all CPUs as being on
Node 0. On LPARs or KVM guests where Node 0 is memoryless, this leads to
a high number of slab deactivations
(http://www.spinics.net/lists/linux-mm/msg67489.html).
Fix this by initializing the powerpc-specific CPU<->node/local memory
node mapping as early as possible, which on powerpc is
do_init_bootmem(). Currently that function initializes the mapping for
the boot CPU, but we extend it to setup the mapping for all possible
CPUs. Then, in smp_prepare_cpus(), we can correspondingly set the
per-cpu values for all possible CPUs. That ensures that before the
early_initcalls run (and really as early as possible), the per-cpu NUMA
mapping is accurate.
While testing memoryless nodes on PowerKVM guests with a fix to the
workqueue logic to use cpu_to_mem() instead of cpu_to_node(), with a
guest topology of:
available: 2 nodes (0-1)
node 0 cpus: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49
node 0 size: 0 MB
node 0 free: 0 MB
node 1 cpus: 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99
node 1 size: 16336 MB
node 1 free: 15329 MB
node distances:
node 0 1
0: 10 40
1: 40 10
the slab consumption decreases from
Slab: 932416 kB
SUnreclaim: 902336 kB
to
Slab: 395264 kB
SUnreclaim: 359424 kB
And we a corresponding increase in the slab efficiency from
slab mem objs slabs
used active active
------------------------------------------------------------
kmalloc-16384 337 MB 11.28% 100.00%
task_struct 288 MB 9.93% 100.00%
to
slab mem objs slabs
used active active
------------------------------------------------------------
kmalloc-16384 37 MB 100.00% 100.00%
task_struct 31 MB 100.00% 100.00%
Powerpc didn't support memoryless nodes until recently (64bb80d87f
"powerpc/numa: Enable CONFIG_HAVE_MEMORYLESS_NODES" and 8c27226119
"powerpc/numa: Enable USE_PERCPU_NUMA_NODE_ID"). Those commits also
helped improve memory consumption with these kind of environments.
Signed-off-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch disables the branch target address CAM which under specific
circumstances may cause the processor to skip execution of 1-4
instructions. This fixes IBM Erratum #47.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we take full hotplug to recover from EEH errors, PCI buses
could be involved. For the case, the child devices of involved
PCI buses can't be attached to IOMMU group properly, which is
caused by commit 3f28c5a ("powerpc/powernv: Reduce multi-hit of
iommu_add_device()").
When adding the PCI devices of the newly created PCI buses to
the system, the IOMMU group is expected to be added in (C).
(A) fails to bind the IOMMU group because bus->is_added is
false. (B) fails because the device doesn't have binding IOMMU
table yet. bus->is_added is set to true at end of (C) and
pdev->is_added is set to true at (D).
pcibios_add_pci_devices()
pci_scan_bridge()
pci_scan_child_bus()
pci_scan_slot()
pci_scan_single_device()
pci_scan_device()
pci_device_add()
pcibios_add_device() A: Ignore
device_add() B: Ignore
pcibios_fixup_bus()
pcibios_setup_bus_devices()
pcibios_setup_device() C: Hit
pcibios_finish_adding_to_bus()
pci_bus_add_devices()
pci_bus_add_device() D: Add device
If the parent PCI bus isn't involved in hotplug, the IOMMU
group is expected to be bound in (B). (A) should fail as the
sysfs entries aren't populated.
The patch fixes the issue by reverting commit 3f28c5a and remove
WARN_ON() in iommu_add_device() to allow calling the function
even the specified device already has associated IOMMU group.
Cc: <stable@vger.kernel.org> # 3.16+
Reported-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Once again, we see
arch/powerpc/kernel/exceptions-64s.S: Assembler messages:
arch/powerpc/kernel/exceptions-64s.S:865: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:866: Error: attempt to move .org backwards
arch/powerpc/kernel/exceptions-64s.S:890: Error: attempt to move .org backwards
when compiling ppc:allmodconfig.
This time the problem has been caused by to commit 0869b6fd20
("powerpc/book3s: Add basic infrastructure to handle HMI in Linux"),
which adds functions hmi_exception_early and hmi_exception_after_realmode
into a critical (size-limited) code area, even though that does not appear
to be necessary.
Move those functions to a non-critical area of the file.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull arch signal handling cleanup from Richard Weinberger:
"This patch series moves all remaining archs to the get_signal(),
signal_setup_done() and sigsp() functions.
Currently these archs use open coded variants of the said functions.
Further, unused parameters get removed from get_signal_to_deliver(),
tracehook_signal_handler() and signal_delivered().
At the end of the day we save around 500 lines of code."
* 'signal-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/misc: (43 commits)
powerpc: Use sigsp()
openrisc: Use sigsp()
mn10300: Use sigsp()
mips: Use sigsp()
microblaze: Use sigsp()
metag: Use sigsp()
m68k: Use sigsp()
m32r: Use sigsp()
hexagon: Use sigsp()
frv: Use sigsp()
cris: Use sigsp()
c6x: Use sigsp()
blackfin: Use sigsp()
avr32: Use sigsp()
arm64: Use sigsp()
arc: Use sigsp()
sas_ss_flags: Remove nested ternary if
Rip out get_signal_to_deliver()
Clean up signal_delivered()
tracehook_signal_handler: Remove sig, info, ka and regs
...
Merge more incoming from Andrew Morton:
"Two new syscalls:
memfd_create in "shm: add memfd_create() syscall"
kexec_file_load in "kexec: implementation of new syscall kexec_file_load"
And:
- Most (all?) of the rest of MM
- Lots of the usual misc bits
- fs/autofs4
- drivers/rtc
- fs/nilfs
- procfs
- fork.c, exec.c
- more in lib/
- rapidio
- Janitorial work in filesystems: fs/ufs, fs/reiserfs, fs/adfs,
fs/cramfs, fs/romfs, fs/qnx6.
- initrd/initramfs work
- "file sealing" and the memfd_create() syscall, in tmpfs
- add pci_zalloc_consistent, use it in lots of places
- MAINTAINERS maintenance
- kexec feature work"
* emailed patches from Andrew Morton <akpm@linux-foundation.org: (193 commits)
MAINTAINERS: update nomadik patterns
MAINTAINERS: update usb/gadget patterns
MAINTAINERS: update DMA BUFFER SHARING patterns
kexec: verify the signature of signed PE bzImage
kexec: support kexec/kdump on EFI systems
kexec: support for kexec on panic using new system call
kexec-bzImage64: support for loading bzImage using 64bit entry
kexec: load and relocate purgatory at kernel load time
purgatory: core purgatory functionality
purgatory/sha256: provide implementation of sha256 in purgaotory context
kexec: implementation of new syscall kexec_file_load
kexec: new syscall kexec_file_load() declaration
kexec: make kexec_segment user buffer pointer a union
resource: provide new functions to walk through resources
kexec: use common function for kimage_normal_alloc() and kimage_crash_alloc()
kexec: move segment verification code in a separate function
kexec: rename unusebale_pages to unusable_pages
kernel: build bin2c based on config option CONFIG_BUILD_BIN2C
bin2c: move bin2c in scripts/basic
shm: wait for pins to be released when sealing
...
Replace strict_strto calls with more appropriate kstrto calls
Signed-off-by: Daniel Walter <dwalter@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The core mm code will provide a default gate area based on
FIXADDR_USER_START and FIXADDR_USER_END if
!defined(__HAVE_ARCH_GATE_AREA) && defined(AT_SYSINFO_EHDR).
This default is only useful for ia64. arm64, ppc, s390, sh, tile, 64-bit
UML, and x86_32 have their own code just to disable it. arm, 32-bit UML,
and x86_64 have gate areas, but they have their own implementations.
This gets rid of the default and moves the code into ia64.
This should save some code on architectures without a gate area: it's now
possible to inline the gate_area functions in the default case.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: Nathan Lynch <nathan_lynch@mentor.com>
Acked-by: H. Peter Anvin <hpa@linux.intel.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> [in principle]
Acked-by: Richard Weinberger <richard@nod.at> [for um]
Acked-by: Will Deacon <will.deacon@arm.com> [for arm64]
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Nathan Lynch <Nathan_Lynch@mentor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
they had small conflicts (respectively within KVM documentation,
and with 3.16-rc changes). Since they were all within the subsystem,
I took care of them.
Stephen Rothwell reported some snags in PPC builds, but they are all
fixed now; the latest linux-next report was clean.
New features for ARM include:
- KVM VGIC v2 emulation on GICv3 hardware
- Big-Endian support for arm/arm64 (guest and host)
- Debug Architecture support for arm64 (arm32 is on Christoffer's todo list)
And for PPC:
- Book3S: Good number of LE host fixes, enable HV on LE
- Book3S HV: Add in-guest debug support
This release drops support for KVM on the PPC440. As a result, the
PPC merge removes more lines than it adds. :)
I also included an x86 change, since Davidlohr tied it to an independent
bug report and the reporter quickly provided a Tested-by; there was no
reason to wait for -rc2.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=hyQP
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull second round of KVM changes from Paolo Bonzini:
"Here are the PPC and ARM changes for KVM, which I separated because
they had small conflicts (respectively within KVM documentation, and
with 3.16-rc changes). Since they were all within the subsystem, I
took care of them.
Stephen Rothwell reported some snags in PPC builds, but they are all
fixed now; the latest linux-next report was clean.
New features for ARM include:
- KVM VGIC v2 emulation on GICv3 hardware
- Big-Endian support for arm/arm64 (guest and host)
- Debug Architecture support for arm64 (arm32 is on Christoffer's todo list)
And for PPC:
- Book3S: Good number of LE host fixes, enable HV on LE
- Book3S HV: Add in-guest debug support
This release drops support for KVM on the PPC440. As a result, the
PPC merge removes more lines than it adds. :)
I also included an x86 change, since Davidlohr tied it to an
independent bug report and the reporter quickly provided a Tested-by;
there was no reason to wait for -rc2"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (122 commits)
KVM: Move more code under CONFIG_HAVE_KVM_IRQFD
KVM: nVMX: fix "acknowledge interrupt on exit" when APICv is in use
KVM: nVMX: Fix nested vmexit ack intr before load vmcs01
KVM: PPC: Enable IRQFD support for the XICS interrupt controller
KVM: Give IRQFD its own separate enabling Kconfig option
KVM: Move irq notifier implementation into eventfd.c
KVM: Move all accesses to kvm::irq_routing into irqchip.c
KVM: irqchip: Provide and use accessors for irq routing table
KVM: Don't keep reference to irq routing table in irqfd struct
KVM: PPC: drop duplicate tracepoint
arm64: KVM: fix 64bit CP15 VM access for 32bit guests
KVM: arm64: GICv3: mandate page-aligned GICV region
arm64: KVM: GICv3: move system register access to msr_s/mrs_s
KVM: PPC: PR: Handle FSCR feature deselects
KVM: PPC: HV: Remove generic instruction emulation
KVM: PPC: BOOKEHV: rename e500hv_spr to bookehv_spr
KVM: PPC: Remove DCR handling
KVM: PPC: Expose helper functions for data/inst faults
KVM: PPC: Separate loadstore emulation from priv emulation
KVM: PPC: Handle magic page in kvmppc_ld/st
...
Pull powerpc updates from Ben Herrenschmidt:
"This is the powerpc new goodies for 3.17. The short story:
The biggest bit is Michael removing all of pre-POWER4 processor
support from the 64-bit kernel. POWER3 and rs64. This gets rid of a
ton of old cruft that has been bitrotting in a long while. It was
broken for quite a few versions already and nobody noticed. Nobody
uses those machines anymore. While at it, he cleaned up a bunch of
old dusty cabinets, getting rid of a skeletton or two.
Then, we have some base VFIO support for KVM, which allows assigning
of PCI devices to KVM guests, support for large 64-bit BARs on
"powernv" platforms, support for HMI (Hardware Management Interrupts)
on those same platforms, some sparse-vmemmap improvements (for memory
hotplug),
There is the usual batch of Freescale embedded updates (summary in the
merge commit) and fixes here or there, I think that's it for the
highlights"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (102 commits)
powerpc/eeh: Export eeh_iommu_group_to_pe()
powerpc/eeh: Add missing #ifdef CONFIG_IOMMU_API
powerpc: Reduce scariness of interrupt frames in stack traces
powerpc: start loop at section start of start in vmemmap_populated()
powerpc: implement vmemmap_free()
powerpc: implement vmemmap_remove_mapping() for BOOK3S
powerpc: implement vmemmap_list_free()
powerpc: Fail remap_4k_pfn() if PFN doesn't fit inside PTE
powerpc/book3s: Fix endianess issue for HMI handling on napping cpus.
powerpc/book3s: handle HMIs for cpus in nap mode.
powerpc/powernv: Invoke opal call to handle hmi.
powerpc/book3s: Add basic infrastructure to handle HMI in Linux.
powerpc/iommu: Fix comments with it_page_shift
powerpc/powernv: Handle compound PE in config accessors
powerpc/powernv: Handle compound PE for EEH
powerpc/powernv: Handle compound PE
powerpc/powernv: Split ioda_eeh_get_state()
powerpc/powernv: Allow to freeze PE
powerpc/powernv: Enable M64 aperatus for PHB3
powerpc/eeh: Aux PE data for error log
...
The function is used by VFIO driver, which might be built as a
dynamic module. So it should be exported.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use the more generic functions get_signal() signal_setup_done()
for signal delivery.
This inverts also the return codes of setup_*frame() to follow the
kernel convention.
Signed-off-by: Richard Weinberger <richard@nod.at>
Pull timer and time updates from Thomas Gleixner:
"A rather large update of timers, timekeeping & co
- Core timekeeping code is year-2038 safe now for 32bit machines.
Now we just need to fix all in kernel users and the gazillion of
user space interfaces which rely on timespec/timeval :)
- Better cache layout for the timekeeping internal data structures.
- Proper nanosecond based interfaces for in kernel users.
- Tree wide cleanup of code which wants nanoseconds but does hoops
and loops to convert back and forth from timespecs. Some of it
definitely belongs into the ugly code museum.
- Consolidation of the timekeeping interface zoo.
- A fast NMI safe accessor to clock monotonic for tracing. This is a
long standing request to support correlated user/kernel space
traces. With proper NTP frequency correction it's also suitable
for correlation of traces accross separate machines.
- Checkpoint/restart support for timerfd.
- A few NOHZ[_FULL] improvements in the [hr]timer code.
- Code move from kernel to kernel/time of all time* related code.
- New clocksource/event drivers from the ARM universe. I'm really
impressed that despite an architected timer in the newer chips SoC
manufacturers insist on inventing new and differently broken SoC
specific timers.
[ Ed. "Impressed"? I don't think that word means what you think it means ]
- Another round of code move from arch to drivers. Looks like most
of the legacy mess in ARM regarding timers is sorted out except for
a few obnoxious strongholds.
- The usual updates and fixlets all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (114 commits)
timekeeping: Fixup typo in update_vsyscall_old definition
clocksource: document some basic timekeeping concepts
timekeeping: Use cached ntp_tick_length when accumulating error
timekeeping: Rework frequency adjustments to work better w/ nohz
timekeeping: Minor fixup for timespec64->timespec assignment
ftrace: Provide trace clocks monotonic
timekeeping: Provide fast and NMI safe access to CLOCK_MONOTONIC
seqcount: Add raw_write_seqcount_latch()
seqcount: Provide raw_read_seqcount()
timekeeping: Use tk_read_base as argument for timekeeping_get_ns()
timekeeping: Create struct tk_read_base and use it in struct timekeeper
timekeeping: Restructure the timekeeper some more
clocksource: Get rid of cycle_last
clocksource: Move cycle_last validation to core code
clocksource: Make delta calculation a function
wireless: ath9k: Get rid of timespec conversions
drm: vmwgfx: Use nsec based interfaces
drm: i915: Use nsec based interfaces
timekeeping: Provide ktime_get_raw()
hangcheck-timer: Use ktime_get_ns()
...
Some new functions are exposed for use by the IOMMU code but
won't build when CONFIG_IOMMU_API isn't set, so shield them
appropriately.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Highlights in this release include:
- BookE: Rework instruction fetch, not racy anymore now
- BookE HV: Fix ONE_REG accessors for some in-hardware registers
- Book3S: Good number of LE host fixes, enable HV on LE
- Book3S: Some misc bug fixes
- Book3S HV: Add in-guest debug support
- Book3S HV: Preload cache lines on context switch
- Remove 440 support
Alexander Graf (31):
KVM: PPC: Book3s PR: Disable AIL mode with OPAL
KVM: PPC: Book3s HV: Fix tlbie compile error
KVM: PPC: Book3S PR: Handle hyp doorbell exits
KVM: PPC: Book3S PR: Fix ABIv2 on LE
KVM: PPC: Book3S PR: Fix sparse endian checks
PPC: Add asm helpers for BE 32bit load/store
KVM: PPC: Book3S HV: Make HTAB code LE host aware
KVM: PPC: Book3S HV: Access guest VPA in BE
KVM: PPC: Book3S HV: Access host lppaca and shadow slb in BE
KVM: PPC: Book3S HV: Access XICS in BE
KVM: PPC: Book3S HV: Fix ABIv2 on LE
KVM: PPC: Book3S HV: Enable for little endian hosts
KVM: PPC: Book3S: Move vcore definition to end of kvm_arch struct
KVM: PPC: Deflect page write faults properly in kvmppc_st
KVM: PPC: Book3S: Stop PTE lookup on write errors
KVM: PPC: Book3S: Add hack for split real mode
KVM: PPC: Book3S: Make magic page properly 4k mappable
KVM: PPC: Remove 440 support
KVM: Rename and add argument to check_extension
KVM: Allow KVM_CHECK_EXTENSION on the vm fd
KVM: PPC: Book3S: Provide different CAPs based on HV or PR mode
KVM: PPC: Implement kvmppc_xlate for all targets
KVM: PPC: Move kvmppc_ld/st to common code
KVM: PPC: Remove kvmppc_bad_hva()
KVM: PPC: Use kvm_read_guest in kvmppc_ld
KVM: PPC: Handle magic page in kvmppc_ld/st
KVM: PPC: Separate loadstore emulation from priv emulation
KVM: PPC: Expose helper functions for data/inst faults
KVM: PPC: Remove DCR handling
KVM: PPC: HV: Remove generic instruction emulation
KVM: PPC: PR: Handle FSCR feature deselects
Alexey Kardashevskiy (1):
KVM: PPC: Book3S: Fix LPCR one_reg interface
Aneesh Kumar K.V (4):
KVM: PPC: BOOK3S: PR: Fix PURR and SPURR emulation
KVM: PPC: BOOK3S: PR: Emulate virtual timebase register
KVM: PPC: BOOK3S: PR: Emulate instruction counter
KVM: PPC: BOOK3S: HV: Update compute_tlbie_rb to handle 16MB base page
Anton Blanchard (2):
KVM: PPC: Book3S HV: Fix ABIv2 indirect branch issue
KVM: PPC: Assembly functions exported to modules need _GLOBAL_TOC()
Bharat Bhushan (10):
kvm: ppc: bookehv: Added wrapper macros for shadow registers
kvm: ppc: booke: Use the shared struct helpers of SRR0 and SRR1
kvm: ppc: booke: Use the shared struct helpers of SPRN_DEAR
kvm: ppc: booke: Add shared struct helpers of SPRN_ESR
kvm: ppc: booke: Use the shared struct helpers for SPRN_SPRG0-7
kvm: ppc: Add SPRN_EPR get helper function
kvm: ppc: bookehv: Save restore SPRN_SPRG9 on guest entry exit
KVM: PPC: Booke-hv: Add one reg interface for SPRG9
KVM: PPC: Remove comment saying SPRG1 is used for vcpu pointer
KVM: PPC: BOOKEHV: rename e500hv_spr to bookehv_spr
Michael Neuling (1):
KVM: PPC: Book3S HV: Add H_SET_MODE hcall handling
Mihai Caraman (8):
KVM: PPC: e500mc: Enhance tlb invalidation condition on vcpu schedule
KVM: PPC: e500: Fix default tlb for victim hint
KVM: PPC: e500: Emulate power management control SPR
KVM: PPC: e500mc: Revert "add load inst fixup"
KVM: PPC: Book3e: Add TLBSEL/TSIZE defines for MAS0/1
KVM: PPC: Book3s: Remove kvmppc_read_inst() function
KVM: PPC: Allow kvmppc_get_last_inst() to fail
KVM: PPC: Bookehv: Get vcpu's last instruction for emulation
Paul Mackerras (4):
KVM: PPC: Book3S: Controls for in-kernel sPAPR hypercall handling
KVM: PPC: Book3S: Allow only implemented hcalls to be enabled or disabled
KVM: PPC: Book3S PR: Take SRCU read lock around RTAS kvm_read_guest() call
KVM: PPC: Book3S: Make kvmppc_ld return a more accurate error indication
Stewart Smith (2):
Split out struct kvmppc_vcore creation to separate function
Use the POWER8 Micro Partition Prefetch Engine in KVM HV on POWER8
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=JuLr
-----END PGP SIGNATURE-----
Merge tag 'signed-kvm-ppc-next' of git://github.com/agraf/linux-2.6 into kvm
Patch queue for ppc - 2014-08-01
Highlights in this release include:
- BookE: Rework instruction fetch, not racy anymore now
- BookE HV: Fix ONE_REG accessors for some in-hardware registers
- Book3S: Good number of LE host fixes, enable HV on LE
- Book3S: Some misc bug fixes
- Book3S HV: Add in-guest debug support
- Book3S HV: Preload cache lines on context switch
- Remove 440 support
Alexander Graf (31):
KVM: PPC: Book3s PR: Disable AIL mode with OPAL
KVM: PPC: Book3s HV: Fix tlbie compile error
KVM: PPC: Book3S PR: Handle hyp doorbell exits
KVM: PPC: Book3S PR: Fix ABIv2 on LE
KVM: PPC: Book3S PR: Fix sparse endian checks
PPC: Add asm helpers for BE 32bit load/store
KVM: PPC: Book3S HV: Make HTAB code LE host aware
KVM: PPC: Book3S HV: Access guest VPA in BE
KVM: PPC: Book3S HV: Access host lppaca and shadow slb in BE
KVM: PPC: Book3S HV: Access XICS in BE
KVM: PPC: Book3S HV: Fix ABIv2 on LE
KVM: PPC: Book3S HV: Enable for little endian hosts
KVM: PPC: Book3S: Move vcore definition to end of kvm_arch struct
KVM: PPC: Deflect page write faults properly in kvmppc_st
KVM: PPC: Book3S: Stop PTE lookup on write errors
KVM: PPC: Book3S: Add hack for split real mode
KVM: PPC: Book3S: Make magic page properly 4k mappable
KVM: PPC: Remove 440 support
KVM: Rename and add argument to check_extension
KVM: Allow KVM_CHECK_EXTENSION on the vm fd
KVM: PPC: Book3S: Provide different CAPs based on HV or PR mode
KVM: PPC: Implement kvmppc_xlate for all targets
KVM: PPC: Move kvmppc_ld/st to common code
KVM: PPC: Remove kvmppc_bad_hva()
KVM: PPC: Use kvm_read_guest in kvmppc_ld
KVM: PPC: Handle magic page in kvmppc_ld/st
KVM: PPC: Separate loadstore emulation from priv emulation
KVM: PPC: Expose helper functions for data/inst faults
KVM: PPC: Remove DCR handling
KVM: PPC: HV: Remove generic instruction emulation
KVM: PPC: PR: Handle FSCR feature deselects
Alexey Kardashevskiy (1):
KVM: PPC: Book3S: Fix LPCR one_reg interface
Aneesh Kumar K.V (4):
KVM: PPC: BOOK3S: PR: Fix PURR and SPURR emulation
KVM: PPC: BOOK3S: PR: Emulate virtual timebase register
KVM: PPC: BOOK3S: PR: Emulate instruction counter
KVM: PPC: BOOK3S: HV: Update compute_tlbie_rb to handle 16MB base page
Anton Blanchard (2):
KVM: PPC: Book3S HV: Fix ABIv2 indirect branch issue
KVM: PPC: Assembly functions exported to modules need _GLOBAL_TOC()
Bharat Bhushan (10):
kvm: ppc: bookehv: Added wrapper macros for shadow registers
kvm: ppc: booke: Use the shared struct helpers of SRR0 and SRR1
kvm: ppc: booke: Use the shared struct helpers of SPRN_DEAR
kvm: ppc: booke: Add shared struct helpers of SPRN_ESR
kvm: ppc: booke: Use the shared struct helpers for SPRN_SPRG0-7
kvm: ppc: Add SPRN_EPR get helper function
kvm: ppc: bookehv: Save restore SPRN_SPRG9 on guest entry exit
KVM: PPC: Booke-hv: Add one reg interface for SPRG9
KVM: PPC: Remove comment saying SPRG1 is used for vcpu pointer
KVM: PPC: BOOKEHV: rename e500hv_spr to bookehv_spr
Michael Neuling (1):
KVM: PPC: Book3S HV: Add H_SET_MODE hcall handling
Mihai Caraman (8):
KVM: PPC: e500mc: Enhance tlb invalidation condition on vcpu schedule
KVM: PPC: e500: Fix default tlb for victim hint
KVM: PPC: e500: Emulate power management control SPR
KVM: PPC: e500mc: Revert "add load inst fixup"
KVM: PPC: Book3e: Add TLBSEL/TSIZE defines for MAS0/1
KVM: PPC: Book3s: Remove kvmppc_read_inst() function
KVM: PPC: Allow kvmppc_get_last_inst() to fail
KVM: PPC: Bookehv: Get vcpu's last instruction for emulation
Paul Mackerras (4):
KVM: PPC: Book3S: Controls for in-kernel sPAPR hypercall handling
KVM: PPC: Book3S: Allow only implemented hcalls to be enabled or disabled
KVM: PPC: Book3S PR: Take SRCU read lock around RTAS kvm_read_guest() call
KVM: PPC: Book3S: Make kvmppc_ld return a more accurate error indication
Stewart Smith (2):
Split out struct kvmppc_vcore creation to separate function
Use the POWER8 Micro Partition Prefetch Engine in KVM HV on POWER8
Conflicts:
Documentation/virtual/kvm/api.txt
Some people see things like "Exception: 501" in stack traces in dmesg
and assume that means that something has gone badly wrong, when in
fact "Exception: 501" just means a device interrupt was taken.
This changes "Exception" to "interrupt" to make it clearer that we
are just recording the fact of a change in control flow rather than
some error condition.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
(NOTE: This patch depends on upstream HMI handling patchset at
https://lists.ozlabs.org/pipermail/linuxppc-dev/2014-July/119731.html)
The current HMI handling on napping cpus does not take care of endianess
issue. On LE host kernel when we wake up from nap due to HMI interrupt we
would checkstop while jumping into opal call. There is a similar issue in
case of fast sleep wakeup where the code invokes opal_resync_tb opal call
without handling LE issue. This patch fixes that as well.
With this patch applied, HMIs handling on LE host kernel works fine.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
HMIs are thread specific and can come while thread is in sleep/nap mode.
Hence with SMT=off mode we can receive HMIs on sleeping threads. For
interrupt received in nap mode, cpu wakes up at system reset vector, clears
the interrupt and go back to nap mode again. But HMIs are sticky and they
keep happening until we clear reason bits from HMER. Hence add a special
check for HMI in reset vector (through power7_wakeup_* functions) and
invoke opal call to handle HMI.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Handle Hypervisor Maintenance Interrupt (HMI) in Linux. This patch implements
basic infrastructure to handle HMI in Linux host. The design is to invoke
opal handle hmi in real mode for recovery and set irq_pending when we hit HMI.
During check_irq_replay pull opal hmi event and print hmi info on console.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There is a couple of commented debug prints which still use
IOMMU_PAGE_SHIFT() which is not defined for POWERPC anymore, replace
them with it_page_shift.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch allows PE (struct eeh_pe) instance to have auxillary data,
whose size is configurable on basis of platform. For PowerNV, the
auxillary data will be used to cache PHB diag-data for that PE
(frozen PE or fenced PHB). In turn, we can retrieve the diag-data
at any later points.
It's useful for the case of VFIO PCI devices where the error log
should be cached, and then be retrieved by the guest at later point.
Also, it can avoid PHB diag-data overwritting if another frozen PE
reported and the previous diag-data isn't fetched by guest.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pr_warn() is equal to pr_warning(), but the former is a bit more
formal according to commit fc62f2f ("kernel.h: add pr_warn for
symmetry to dev_warn, netdev_warn").
The patch replaces pr_warning() with pr_warn().
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch prints 4 PCIE or AER config registers each line, which
is part of the EEH log so that it looks a bit more compact.
Suggested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
According to the experiment I did, PCI config access is blocked
on P7IOC frozen PE by hardware, but PHB3 doesn't do that. That
means we always get 0xFF's while dumping PCI config space of the
frozen PE on P7IOC. We don't have the problem on PHB3. So we have
to enable I/O prioir to collecting error log. Otherwise, meaningless
0xFF's are always returned.
The patch fixes it by EEH flag (EEH_ENABLE_IO_FOR_LOG), which is
selectively set to indicate the case for: P7IOC on PowerNV platform,
pSeries platform.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There are multiple global EEH flags. Almost each flag has its own
accessor, which doesn't make sense. The patch refactors EEH flag
accessors so that they look unified:
eeh_add_flag(): Add EEH flag
eeh_clear_flag(): Clear EEH flag
eeh_has_flag(): Check if one specific flag has been set
eeh_enabled(): Check if EEH functionality has been enabled
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Function eeh_iommu_group_to_pe() iterates each PCI device to check
the binding IOMMU group with get_iommu_table_base(), which possibly
fetches pdev->dev.archdata.dma_data.dma_offset. It's (0x1 << 59)
for "bypass" cases.
The patch fixes the issue by iterating devices hooked to the IOMMU
group and fetch IOMMU table there.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pci_get_slot() is called with hold of PCI bus semaphore and it's not
safe to be called in interrupt context. However, we possibly checks
EEH error and calls the function in interrupt context. To avoid using
pci_get_slot(), we turn into device tree for fetching location code.
Otherwise, we might run into WARN_ON() as following messages indicate:
WARNING: at drivers/pci/search.c:223
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.16.0-rc3+ #72
task: c000000001367af0 ti: c000000001444000 task.ti: c000000001444000
NIP: c000000000497b70 LR: c000000000037530 CTR: 000000003003d114
REGS: c000000001446fa0 TRAP: 0700 Not tainted (3.16.0-rc3+)
MSR: 9000000000029032 <SF,HV,EE,ME,IR,DR,RI> CR: 48002422 XER: 20000000
CFAR: c00000000003752c SOFTE: 0
:
NIP [c000000000497b70] .pci_get_slot+0x40/0x110
LR [c000000000037530] .eeh_pe_loc_get+0x150/0x190
Call Trace:
.of_get_property+0x30/0x60 (unreliable)
.eeh_pe_loc_get+0x150/0x190
.eeh_dev_check_failure+0x1b4/0x550
.eeh_check_failure+0x90/0xf0
.lpfc_sli_check_eratt+0x504/0x7c0 [lpfc]
.lpfc_poll_eratt+0x64/0x100 [lpfc]
.call_timer_fn+0x64/0x190
.run_timer_softirq+0x2cc/0x3e0
Cc: stable@vger.kernel.org
Signed-off-by: Mike Qiu <qiudayu@linux.vnet.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The sysfs entries are lost because of commit 2213fb1 ("powerpc/eeh:
Skip eeh sysfs when eeh is disabled"). That commit added condition
to create sysfs entries with EEH_ENABLED, which isn't populated
when trying to create sysfs entries on PowerNV platform during system
boot time. The patch fixes the issue by:
* Reoder EEH initialization functions so that they're same on
PowerNV/pSeries.
* Cache PE's primary bus by PowerNV platform instead of EEH core
to avoid kernel crash caused by the function reorder. Another
benefit with this is to avoid one eeh_probe_mode_dev() in EEH
core.
Signed-off-by: Mike Qiu <qiudayu@linux.vnet.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch exports functions to be used by new VFIO ioctl command,
which will be introduced in subsequent patch, to support EEH
functinality for VFIO PCI devices.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We must not handle EEH error on devices which are passed to somebody
else. Instead, we expect that the frozen device owner detects an EEH
error and recovers from it.
This avoids EEH error handling on passed through devices so the device
owner gets a chance to handle them.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Scott writes:
Highlights include e6500 hardware threading support, an e6500 TLB erratum
workaround, corenet error reporting, support for a new board, and some
minor fixes.
to the ftrace function callback infrastructure. It's introducing a
way to allow different functions to call directly different trampolines
instead of all calling the same "mcount" one.
The only user of this for now is the function graph tracer, which always
had a different trampoline, but the function tracer trampoline was called
and did basically nothing, and then the function graph tracer trampoline
was called. The difference now, is that the function graph tracer
trampoline can be called directly if a function is only being traced by
the function graph trampoline. If function tracing is also happening on
the same function, the old way is still done.
The accounting for this takes up more memory when function graph tracing
is activated, as it needs to keep track of which functions it uses.
I have a new way that wont take as much memory, but it's not ready yet
for this merge window, and will have to wait for the next one.
Another big change was the removal of the ftrace_start/stop() calls that
were used by the suspend/resume code that stopped function tracing when
entering into suspend and resume paths. The stop of ftrace was done
because there was some function that would crash the system if one called
smp_processor_id()! The stop/start was a big hammer to solve the issue
at the time, which was when ftrace was first introduced into Linux.
Now ftrace has better infrastructure to debug such issues, and I found
the problem function and labeled it with "notrace" and function tracing
can now safely be activated all the way down into the guts of suspend
and resume.
Other changes include clean ups of uprobe code.
Clean up of the trace_seq() code.
And other various small fixes and clean ups to ftrace and tracing.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJT35zXAAoJEKQekfcNnQGuOz0H/38zqM0nLFhrgvz3EPk2UOjn
xqpX8qyb2V7TJZL+IqeXU2a5cQZl5ba0D4WtBGpxbTae3CJYiuQ87iKUNFoH0om5
FDpn80igb368k8V3qRdRsziKVCCf0XBd/NkHJXc0ZkfXGyzB2Ga4bBxALxp2gj9y
bnO+vKo6+tWYKG4hyQb4P3LRXUrK8/LWEsPr39cH2QH1Rdj69Lx9CgrCdUVJmwcb
Bj8hEiLXL/RYCFNn79A3wNTUvW0rG/AOIf4SLqXtasSRZ0ToaU0ZyDnrNv+0Ol47
rX8tSk+LfXchL9hpIvjCf1vlAYq3pO02favteR/jip3lx/dTjEDE4RJ9qtJzZ4Q=
=fwQY
-----END PGP SIGNATURE-----
Merge tag 'trace-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"This pull request has a lot of work done. The main thing is the
changes to the ftrace function callback infrastructure. It's
introducing a way to allow different functions to call directly
different trampolines instead of all calling the same "mcount" one.
The only user of this for now is the function graph tracer, which
always had a different trampoline, but the function tracer trampoline
was called and did basically nothing, and then the function graph
tracer trampoline was called. The difference now, is that the
function graph tracer trampoline can be called directly if a function
is only being traced by the function graph trampoline. If function
tracing is also happening on the same function, the old way is still
done.
The accounting for this takes up more memory when function graph
tracing is activated, as it needs to keep track of which functions it
uses. I have a new way that wont take as much memory, but it's not
ready yet for this merge window, and will have to wait for the next
one.
Another big change was the removal of the ftrace_start/stop() calls
that were used by the suspend/resume code that stopped function
tracing when entering into suspend and resume paths. The stop of
ftrace was done because there was some function that would crash the
system if one called smp_processor_id()! The stop/start was a big
hammer to solve the issue at the time, which was when ftrace was first
introduced into Linux. Now ftrace has better infrastructure to debug
such issues, and I found the problem function and labeled it with
"notrace" and function tracing can now safely be activated all the way
down into the guts of suspend and resume
Other changes include clean ups of uprobe code, clean up of the
trace_seq() code, and other various small fixes and clean ups to
ftrace and tracing"
* tag 'trace-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (57 commits)
ftrace: Add warning if tramp hash does not match nr_trampolines
ftrace: Fix trampoline hash update check on rec->flags
ring-buffer: Use rb_page_size() instead of open coded head_page size
ftrace: Rename ftrace_ops field from trampolines to nr_trampolines
tracing: Convert local function_graph functions to static
ftrace: Do not copy old hash when resetting
tracing: let user specify tracing_thresh after selecting function_graph
ring-buffer: Always run per-cpu ring buffer resize with schedule_work_on()
tracing: Remove function_trace_stop and HAVE_FUNCTION_TRACE_MCOUNT_TEST
s390/ftrace: remove check of obsolete variable function_trace_stop
arm64, ftrace: Remove check of obsolete variable function_trace_stop
Blackfin: ftrace: Remove check of obsolete variable function_trace_stop
metag: ftrace: Remove check of obsolete variable function_trace_stop
microblaze: ftrace: Remove check of obsolete variable function_trace_stop
MIPS: ftrace: Remove check of obsolete variable function_trace_stop
parisc: ftrace: Remove check of obsolete variable function_trace_stop
sh: ftrace: Remove check of obsolete variable function_trace_stop
sparc64,ftrace: Remove check of obsolete variable function_trace_stop
tile: ftrace: Remove check of obsolete variable function_trace_stop
ftrace: x86: Remove check of obsolete variable function_trace_stop
...
The general idea is that each core will release all of its
threads into the secondary thread startup code, which will
eventually wait in the secondary core holding area, for the
appropriate bit in the PACA to be set. The kick_cpu function
pointer will set that bit in the PACA, and thus "release"
the core/thread to boot. We also need to do a few things that
U-Boot normally does for CPUs (like enable branch prediction).
Signed-off-by: Andy Fleming <afleming@freescale.com>
[scottwood@freescale.com: various changes, including only enabling
threads if Linux wants to kick them]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Pull powerpc fixes from Ben Herrenschmidt:
"Here are 3 more small powerpc fixes that should still go into .16.
One is a recent regression (MMCR2 business), the other is a trivial
endian fix without which FW updates won't work on LE in IBM machines,
and the 3rd one turns a BUG_ON into a WARN_ON which is definitely a
LOT more friendly especially when the whole thing is about retrieving
error logs ..."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix endianness of flash_block_list in rtas_flash
powerpc/powernv: Change BUG_ON to WARN_ON in elog code
powerpc/perf: Fix MMCR2 handling for EBB
SPRN_SPRG is used by debug interrupt handler, so this is required for
debug support.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This provides a way for userspace controls which sPAPR hcalls get
handled in the kernel. Each hcall can be individually enabled or
disabled for in-kernel handling, except for H_RTAS. The exception
for H_RTAS is because userspace can already control whether
individual RTAS functions are handled in-kernel or not via the
KVM_PPC_RTAS_DEFINE_TOKEN ioctl, and because the numeric value for
H_RTAS is out of the normal sequence of hcall numbers.
Hcalls are enabled or disabled using the KVM_ENABLE_CAP ioctl for the
KVM_CAP_PPC_ENABLE_HCALL capability on the file descriptor for the VM.
The args field of the struct kvm_enable_cap specifies the hcall number
in args[0] and the enable/disable flag in args[1]; 0 means disable
in-kernel handling (so that the hcall will always cause an exit to
userspace) and 1 means enable. Enabling or disabling in-kernel
handling of an hcall is effective across the whole VM.
The ability for KVM_ENABLE_CAP to be used on a VM file descriptor
on PowerPC is new, added by this commit. The KVM_CAP_ENABLE_CAP_VM
capability advertises that this ability exists.
When a VM is created, an initial set of hcalls are enabled for
in-kernel handling. The set that is enabled is the set that have
an in-kernel implementation at this point. Any new hcall
implementations from this point onwards should not be added to the
default set without a good reason.
No distinction is made between real-mode and virtual-mode hcall
implementations; the one setting controls them both.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
I spent ten minutes scratching my head, trying to work out where we
enabled relocation on interrupts for guest kernels. Expand the doco to
make it clear.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
DISABLE_INTS has a long and storied history, but for some time now it
has not actually disabled interrupts.
For the open-coded exception handlers, just stop using it, instead call
RECONCILE_IRQ_STATE directly. This has the benefit of removing a level
of indirection, and making it clear that r10 & r11 are used at that
point.
For the addition case we still need a macro, so rename it to clarify
what it actually does.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
At the moment the allmodconfig build is failing because we run out of
space between altivec_assist() at 0x5700 and the fwnmi_data_area at
0x7000.
Fixing it permanently will take some more work, but a quick fix is to
move bad_stack() below the fwnmi_data_area. That gives us just enough
room with everything enabled.
bad_stack() is called from the common exception handlers, but it's a
non-conditional branch, so we have plenty of scope to move it further
way.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have a strange #define in cputable.h called CLASSIC_PPC.
Although it is defined for 32 & 64bit, it's only used for 32bit and
it's basically a duplicate of CONFIG_PPC_BOOK3S_32, so let's use
the latter.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The previous patch left a bit of a wart in copy_process(). Clean it up a
bit by moving the logic out into a helper.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We now only support cpus that use an SLB, so we don't need an MMU
feature to indicate that.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Old cpus didn't have a Segment Lookaside Buffer (SLB), instead they had
a Segment Table (STAB). Now that we've dropped support for those cpus,
we can remove the STAB support entirely.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We inadvertently broke power3 support back in 3.4 with commit
f5339277eb "powerpc: Remove FW_FEATURE ISERIES from arch code".
No one noticed until at least 3.9.
By then we'd also broken it with the optimised memcpy, copy_to/from_user
and clear_user routines. We don't want to add any more complexity to
those just to support ancient cpus, so it seems like it's a good time to
drop support for power3 and earlier.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently we have sys_sigpending and sys_old_getrlimit defined to use
COMPAT_SYS() in systbl.h, but then both are #defined to sys_ni_syscall
in systbl.S.
This seems to have been done when ppc and ppc64 were merged, in commit
9994a33 "Introduce entry_{32,64}.S, misc_{32,64}.S, systbl.S".
AFAICS there's no longer (or never was) any need for this, we can just
use SYSX() for both and remove the #defines to sys_ni_syscall.
The expansion before was:
#define COMPAT_SYS(func) .llong .sys_##func,.compat_sys_##func
#define sys_old_getrlimit sys_ni_syscall
COMPAT_SYS(old_getrlimit)
=>
.llong .sys_old_getrlimit,.compat_sys_old_getrlimit
=>
.llong .sys_ni_syscall,.compat_sys_old_getrlimit
After is:
#define SYSX(f, f3264, f32) .llong .f,.f3264
SYSX(sys_ni_syscall, compat_sys_old_getrlimit, sys_old_getrlimit)
=>
.llong .sys_ni_syscall,.compat_sys_old_getrlimit
ie. they are equivalent.
Finally both COMPAT_SYS() and SYSX() evaluate to sys_ni_syscall in the
Cell SPU code.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The function rtas_flash_firmware passes the address of a data structure,
flash_block_list, when making the update-flash-64-and-reboot rtas call.
While the endianness of the address is handled correctly, the endianness
of the data is not. This patch ensures that the data in flash_block_list
is big endian when passed to rtas on little endian hosts.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
PowerPC does an odd thing with dynamic nodes. It uses a notifier to
catch new node additions and set some of the values like name and type.
This makes no sense since that same code can be put directly into
of_attach_node(). Besides, all dynamic node users need this, not just
powerpc. Fix this problem by moving the logic out of arch/powerpc and
into drivers/of/dynamic.c.
It is also important to remove this notifier because we want to move the
firing of notifiers from before the tree is modified to after so that
the receiver gets a consistent view of the tree, but that is
incompatible with notifiers that modify the node.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Nathan Fontenot <nfont@austin.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull powerpc fixes from Ben Herrenschmidt:
"Here is a handful of powerpc fixes for 3.16. They are all pretty
simple and self contained and should still make this release"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: use _GLOBAL_TOC for memmove
powerpc/pseries: dynamically added OF nodes need to call of_node_init
powerpc: subpage_protect: Increase the array size to take care of 64TB
powerpc: Fix bugs in emulate_step()
powerpc: Disable doorbells on Power8 DD1.x
cycle_last was added to the clocksource to support the TSC
validation. We moved that to the core code, so we can get rid of the
extra copy.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
These processors do not currently support doorbell IPIs, so remove them
from the feature list if we are at DD 1.xx for the 0x004d part.
This fixes a regression caused by d4e58e5928 (powerpc/powernv: Enable
POWER8 doorbell IPIs). With that patch the kernel would hang at boot
when calling smp_call_function_many, as the doorbell would not be
received by the target CPUs:
.smp_call_function_many+0x2bc/0x3c0 (unreliable)
.on_each_cpu_mask+0x30/0x100
.cpuidle_register_driver+0x158/0x1a0
.cpuidle_register+0x2c/0x110
.powernv_processor_idle_init+0x23c/0x2c0
.do_one_initcall+0xd4/0x260
.kernel_init_freeable+0x25c/0x33c
.kernel_init+0x1c/0x120
.ret_from_kernel_thread+0x58/0x7c
Fixes: d4e58e5928 (powerpc/powernv: Enable POWER8 doorbell IPIs)
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
ftrace_stop() is going away as it disables parts of function tracing
that affects users that should not be affected. But ftrace_graph_stop()
is built on ftrace_stop(). Here's another example of killing all of
function tracing because something went wrong with function graph
tracing.
Instead of disabling all users of function tracing on function graph
error, disable only function graph tracing. To do this, the arch code
must call ftrace_graph_is_dead() before it implements function graph.
Cc: Anton Blanchard <anton@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Commit 8d6f7c5a: "powerpc/powernv: Make it possible to skip the IRQHAPPENED
check in power7_nap()" added code that prevents cpus from checking for
pending interrupts just before entering sleep state, which is wrong. These
interrupts are delivered during the soft irq disabled state of the cpu.
A cpu cannot enter any idle state with pending interrupts because they will
never be serviced until the next time the cpu is woken up by some other
interrupt. Its only then that the pending interrupts are replayed. This can result
in device timeouts or warnings about this cpu being stuck.
This patch fixes ths issue by ensuring that cpus check for pending interrupts
just before entering any idle state as long as they are not in the path of split
core operations.
Signed-off-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since the logic to reset PCI secondary bus by PCI config register
PCI_BRIDGE_CTL_BUS_RESET is included in pci_reset_secondary_bus(), we
needn't implement another one.
Remove the duplicate implementation and call pci_reset_secondary_bus().
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit 143e1e28cb (sched: Rework sched_domain topology definition)
introduced a number of functions with a return value of 'const int'.
gcc doesn't know what to do with that and, if the kernel is compiled
with W=1, complains with the following warnings whenever sched.h
is included.
include/linux/sched.h:875:25: warning: type qualifiers ignored on function return type
include/linux/sched.h:882:25: warning: type qualifiers ignored on function return type
include/linux/sched.h:889:25: warning: type qualifiers ignored on function return type
include/linux/sched.h:1002:21: warning: type qualifiers ignored on function return type
Commits fb2aa855 (sched, ARM: Create a dedicated scheduler topology table)
and 607b45e9a (sched, powerpc: Create a dedicated topology table) introduce
the same warning in the arm and powerpc code.
Drop 'const' from the function declarations to fix the problem.
The fix for all three patches has to be applied together to avoid
compilation failures for the affected architectures.
Acked-by: Vincent Guittot <vincent.guittot@linaro.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1403658329-13196-1-git-send-email-linux@roeck-us.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In machine_check_e500 exception handler is a wrong indication
in case of MCSR_BUS_WBERR - so print "Write" instead of "Read".
Signed-off-by: Wladislav Wiebe <wladislav.kw@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Commit 59a53afe70 "powerpc: Don't setup
CPUs with bad status" broke ePAPR SMP booting. ePAPR says that CPUs
that aren't presently running shall have status of disabled, with
enable-method being used to determine whether the CPU can be enabled.
Fix by checking for spin-table, which is currently the only supported
enable-method.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Emil Medve <Emilian.Medve@Freescale.com>
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The commit 71ec7c55ed introduced the magic symbol ".TOC." for ELFv2 ABI.
This symbol is built manually and has no CRC value computed. A zero value
is put in the CRC section to avoid modpost complaining about a missing CRC.
Unfortunately, this breaks the kernel module loading when the kernel is
relocated (kdump case for instance) because of the relocation applied to
the kcrctab values.
This patch compute a CRC value for the TOC symbol which will match the one
compute by the kernel when it is relocated - aka '0 - relocate_start' done in
maybe_relocated called by check_version (module.c).
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Cc: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In commit 27f4488872 "Add OPAL takeover from PowerVM" we added support
for "takeover" on OPAL v1 machines.
This was a mode of operation where we would boot under pHyp, and query
for the presence of OPAL. If detected we would then do a special
sequence to take over the machine, and the kernel would end up running
in hypervisor mode.
OPAL v1 was never a supported product, and was never shipped outside
IBM. As far as we know no one is still using it.
Newer versions of OPAL do not use the takeover mechanism. Although the
query for OPAL should be harmless on machines with newer OPAL, we have
seen a machine where it causes a crash in Open Firmware.
The code in early_init_devtree() to copy boot_command_line into cmd_line
was added in commit 817c21ad9a "Get kernel command line accross OPAL
takeover", and AFAIK is only used by takeover, so should also be
removed.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In commit 721aeaa9 "Build little endian ppc64 kernel with ABIv2", we
missed some updates required in the kprobes code to make jprobes work
when the kernel is built with ABI v2.
Firstly update arch_deref_entry_point() to do the right thing. Now that
we have added ppc_global_function_entry() we can just always use that, it
will do the right thing for 32 & 64 bit and ABI v1 & v2.
Secondly we need to update the code that sets up the register state before
calling the jprobe handler. On ABI v1 we setup r2 to hold the TOC, on ABI
v2 we need to populate r12 with the function entry point address.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The printks() in our ftrace code have no prefix, so they appear on the
console with very little context, eg:
Branch out of range
Use pr_fmt() & pr_err() to add a prefix. While we're at it, collapse a
few split lines that don't need to be, and add a missing newline to one
message.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There is a bug in the handling of the function entry when we are nopping
out a branch from a module in ftrace.
We compare the result of module_trampoline_target() with the value of
ppc_function_entry(), and expect them to be true. But they never will
be.
module_trampoline_target() will always return the global entry point of
the function, whereas ppc_function_entry() will always return the local.
Fix it by using the newly added ppc_global_function_entry().
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In commit 24a1bdc35, "Fix ABIv2 issues with __ftrace_make_call", Anton
changed the logic that creates and patches the branch, and added a
thinko in the check of create_branch(). create_branch() returns the
instruction that was generated, so if we get zero then it succeeded.
The result is we can't ftrace modules:
Branch out of range
WARNING: at ../kernel/trace/ftrace.c:1638
ftrace failed to modify [<d000000004ba001c>] fuse_req_init_context+0x1c/0x90 [fuse]
We should probably fix patch_instruction() to do that check and make the
API saner, but that's a separate patch. For now just invert the test.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In commit 24a1bdc35, "Fix ABIv2 issues with __ftrace_make_call", Anton
changed the logic that checks for the expected code sequence when
patching a module.
We missed the typo in the mask, 0xffff00000 should be 0xffff0000, which
has the effect of making the test always true.
That makes it impossible to ftrace against modules, eg:
Unexpected call sequence: 48000008 e8410018
WARNING: at ../kernel/trace/ftrace.c:1638
ftrace failed to modify [<d000000007cf001c>] rng_dev_open+0x1c/0x70 [rng_core]
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have some compile-time disabled debug code in signal_xx.c. It's from
some ancient time BG, almost certainly part of the original port, given
the very similar code on other arches.
The show_unhandled_signal logic, added in d0c3d534a4 (2.6.24) is
cleaner and prints more useful information, so drop the debug code.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In arch/powerpc/kernel/iomap.c, lots of IO reading accessors missed
to check EEH error as Ben pointed. The patch fixes it.
For the writing accessors, we change the called functions only for
making them look similar to the reading counterparts.
Suggested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull more powerpc updates from Ben Herrenschmidt:
"Here are the remaining bits I was mentioning earlier. Mostly bug
fixes and new selftests from Michael (yay !). He also removed the WSP
platform and A2 core support which were dead before release, so less
clutter.
One little "feature" I snuck in is the doorbell IPI support for
non-virtualized P8 which speeds up IPIs significantly between threads
of a core"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (34 commits)
powerpc/book3s: Fix some ABIv2 issues in machine check code
powerpc/book3s: Fix guest MC delivery mechanism to avoid soft lockups in guest.
powerpc/book3s: Increment the mce counter during machine_check_early call.
powerpc/book3s: Add stack overflow check in machine check handler.
powerpc/book3s: Fix machine check handling for unhandled errors
powerpc/eeh: Dump PE location code
powerpc/powernv: Enable POWER8 doorbell IPIs
powerpc/cpuidle: Only clear LPCR decrementer wakeup bit on fast sleep entry
powerpc/powernv: Fix killed EEH event
powerpc: fix typo 'CONFIG_PMAC'
powerpc: fix typo 'CONFIG_PPC_CPU'
powerpc/powernv: Don't escalate non-existing frozen PE
powerpc/eeh: Report frozen parent PE prior to child PE
powerpc/eeh: Clear frozen state for child PE
powerpc/powernv: Reduce panic timeout from 180s to 10s
powerpc/xmon: avoid format string leaking to printk
selftests/powerpc: Add tests of PMU EBBs
selftests/powerpc: Add support for skipping tests
selftests/powerpc: Put the test in a separate process group
selftests/powerpc: Fix instruction loop for ABIv2 (LE)
...
Pull more scheduler updates from Ingo Molnar:
"Second round of scheduler changes:
- try-to-wakeup and IPI reduction speedups, from Andy Lutomirski
- continued power scheduling cleanups and refactorings, from Nicolas
Pitre
- misc fixes and enhancements"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/deadline: Delete extraneous extern for to_ratio()
sched/idle: Optimize try-to-wake-up IPI
sched/idle: Simplify wake_up_idle_cpu()
sched/idle: Clear polling before descheduling the idle thread
sched, trace: Add a tracepoint for IPI-less remote wakeups
cpuidle: Set polling in poll_idle
sched: Remove redundant assignment to "rt_rq" in update_curr_rt(...)
sched: Rename capacity related flags
sched: Final power vs. capacity cleanups
sched: Remove remaining dubious usage of "power"
sched: Let 'struct sched_group_power' care about CPU capacity
sched/fair: Disambiguate existing/remaining "capacity" usage
sched/fair: Change "has_capacity" to "has_free_capacity"
sched/fair: Remove "power" from 'struct numa_stats'
sched: Fix signedness bug in yield_to()
sched/fair: Use time_after() in record_wakee()
sched/balancing: Reduce the rate of needless idle load balancing
sched/fair: Fix unlocked reads of some cfs_b->quota/period
Fix this dependency on the locking tree's smp_mb*() API changes:
kernel/sched/idle.c:247:3: error: implicit declaration of function ‘smp_mb__after_atomic’ [-Werror=implicit-function-declaration]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit 2749a2f26a (powerpc/book3s: Fix machine check handling for
unhandled errors) introduced a few ABIv2 issues.
We can maintain ABIv1 and ABIv2 compatibility by branching to the
function rather than the dot symbol.
Fixes: 2749a2f26a ("powerpc/book3s: Fix machine check handling for unhandled errors")
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We don't see MCE counter getting increased in /proc/interrupts which gives
false impression of no MCE occurred even when there were MCE events.
The machine check early handling was added for PowerKVM and we missed to
increment the MCE count in the early handler.
We also increment mce counters in the machine_check_exception call, but
in most cases where we handle the error hypervisor never reaches there
unless its fatal and we want to crash. Only during fatal situation we may
see double increment of mce count. We need to fix that. But for
now it always good to have some count increased instead of zero.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently machine check handler does not check for stack overflow for
nested machine check. If we hit another MCE while inside the machine check
handler repeatedly from same address then we get into risk of stack
overflow which can cause huge memory corruption. This patch limits the
nested MCE level to 4 and panic when we cross level 4.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Current code does not check for unhandled/unrecovered errors and return from
interrupt if it is recoverable exception which in-turn triggers same machine
check exception in a loop causing hypervisor to be unresponsive.
This patch fixes this situation and forces hypervisor to panic for
unhandled/unrecovered errors.
This patch also fixes another issue where unrecoverable_exception routine
was called in real mode in case of unrecoverable exception (MSR_RI = 0).
This causes another exception vector 0x300 (data access) during system crash
leading to confusion while debugging cause of the system crash.
Also turn ME bit off while going down, so that when another MCE is hit during
panic path, system will checkstop and hypervisor will get restarted cleanly
by SP.
With the above fixes we now throw correct console messages (see below) while
crashing the system in case of unhandled/unrecoverable machine checks.
--------------
Severe Machine check interrupt [[Not recovered]
Initiator: CPU
Error type: UE [Instruction fetch]
Effective address: 0000000030002864
Oops: Machine check, sig: 7 [#1]
SMP NR_CPUS=2048 NUMA PowerNV
Modules linked in: bork(O) bridge stp llc kvm [last unloaded: bork]
CPU: 36 PID: 55162 Comm: bash Tainted: G O 3.14.0mce #1
task: c000002d72d022d0 ti: c000000007ec0000 task.ti: c000002d72de4000
NIP: 0000000030002864 LR: 00000000300151a4 CTR: 000000003001518c
REGS: c000000007ec3d80 TRAP: 0200 Tainted: G O (3.14.0mce)
MSR: 9000000000041002 <SF,HV,ME,RI> CR: 28222848 XER: 20000000
CFAR: 0000000030002838 DAR: d0000000004d0000 DSISR: 00000000 SOFTE: 1
GPR00: 000000003001512c 0000000031f92cb0 0000000030078af0 0000000030002864
GPR04: d0000000004d0000 0000000000000000 0000000030002864 ffffffffffffffc9
GPR08: 0000000000000024 0000000030008af0 000000000000002c c00000000150e728
GPR12: 9000000000041002 0000000031f90000 0000000010142550 0000000040000000
GPR16: 0000000010143cdc 0000000000000000 00000000101306fc 00000000101424dc
GPR20: 00000000101424e0 000000001013c6f0 0000000000000000 0000000000000000
GPR24: 0000000010143ce0 00000000100f6440 c000002d72de7e00 c000002d72860250
GPR28: c000002d72860240 c000002d72ac0038 0000000000000008 0000000000040000
NIP [0000000030002864] 0x30002864
LR [00000000300151a4] 0x300151a4
Call Trace:
Instruction dump:
XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
---[ end trace 7285f0beac1e29d3 ]---
Sending IPI to other CPUs
IPI complete
OPAL V3 detected !
--------------
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As Ben suggested, it's meaningful to dump PE's location code
for site engineers when hitting EEH errors. The patch introduces
function eeh_pe_loc_get() to retireve the location code from
dev-tree so that we can output it when hitting EEH errors.
If primary PE bus is root bus, the PHB's dev-node would be tried
prior to root port's dev-node. Otherwise, the upstream bridge's
dev-node of the primary PE bus will be check for the location code
directly.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch enables POWER8 doorbell IPIs on powernv.
Since doorbells can only IPI within a core, we test to see when we can use
doorbells and if not we fall back to XICS. This also enables hypervisor
doorbells to wakeup us up from nap/sleep via the LPCR PECEDH bit.
Based on tests by Anton, the best case IPI latency between two threads dropped
from 894ns to 512ns.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On PowerNV platform, EEH errors are reported by IO accessors or poller
driven by interrupt. After the PE is isolated, we won't produce EEH
event for the PE. The current implementation has possibility of EEH
event lost in this way:
The interrupt handler queues one "special" event, which drives the poller.
EEH thread doesn't pick the special event yet. IO accessors kicks in, the
frozen PE is marked as "isolated" and EEH event is queued to the list.
EEH thread runs because of special event and purge all existing EEH events.
However, we never produce an other EEH event for the frozen PE. Eventually,
the PE is marked as "isolated" and we don't have EEH event to recover it.
The patch fixes the issue to keep EEH events for PEs that have been
marked as "isolated" with the help of additional "force" help to
eeh_remove_event().
Reported-by: Rolf Brudeseth <rolfb@us.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit b0d278b7d3 ("powerpc/perf_event: Reduce latency of calling
perf_event_do_pending") added a check for CONFIG_PMAC were a check for
CONFIG_PPC_PMAC was clearly intended.
Fixes: b0d278b7d3 ("powerpc/perf_event: Reduce latency of calling perf_event_do_pending")
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we have the corner case of frozen parent and child PE at the
same time, we have to handle the frozen parent PE prior to the
child. Without clearning the frozen state on parent PE, the child
PE can't be recovered successfully.
The patch searches the EEH PE hierarchy tree and returns the toppest
frozen PE to be handled. It ensures the frozen parent PE will be
handled prior to child PE.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since commit cb523e09 ("powerpc/eeh: Avoid I/O access during PE
reset"), the PE is kept as frozen state on hardware level until
the PE reset is done completely. After that, we explicitly clear
the frozen state of the affected PE. However, there might have
frozen child PEs of the affected PE and we also need clear their
frozen state as well. Otherwise, the recovery is going to fail.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
OPAL will mark a CPU that is guarded as "bad" in the status property of the CPU
node.
Unfortunatley Linux doesn't check this property and will put the bad CPU in the
present map. This has caused hangs on booting when we try to unsplit the core.
This patch checks the CPU is avaliable via this status property before putting
it in the present map.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Tested-by: Anton Blanchard <anton@samba.org>
cc: stable@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Correct the DSCR SPR becoming temporarily corrupted if a task is
context switched during a transaction.
The problem occurs while suspending the task and is caused by saving
the DSCR to thread.dscr after it has already been set to the CPU's
default value:
__switch_to() calls __switch_to_tm()
which calls tm_reclaim_task()
which calls tm_reclaim_thread()
which calls tm_reclaim()
where the DSCR is set to the CPU's default
__switch_to() calls _switch()
where thread.dscr is set to the DSCR
When the task is resumed, it's transaction will be doomed (as usual)
and the DSCR SPR will be corrupted, although the checkpointed value
will be correct. Therefore the DSCR will be immediately corrected by
the transaction aborting, unless it has been suspended. In that case
the incorrect value can be seen by the task until it resumes the
transaction.
The fix is to treat the DSCR similarly to the TAR and save it early
in __switch_to().
A program exposing the problem is added to the kernel self tests as:
tools/testing/selftests/powerpc/tm/tm-resched-dscr.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
CC: <stable@vger.kernel.org> [v3.10+]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
__attribute__ ((unused))
WSP is the last user of CONFIG_PPC_A2, so we remove that as well.
Although CONFIG_PPC_ICSWX still exists, it's no longer selectable for
any Book3E platform, so we can remove the code in mmu-book3e.h that
depended on it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The Kconfig symbol SERIAL_TEXT_DEBUG was removed from
arch/powerpc/Kconfig.debug in v2.6.22. (In v2.6.27 it was also removed
from arch/ppc/Kconfig.debug.) So the check for its macro has evaluated
to false for over five years now. Remove that check and the few lines
of code hidden behind it.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The Vector Crypto category instructions are supported by current POWER8
chips, advertise them to userspace using a specific bit to properly
differentiate with chips of the same architecture level that might not
have them.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org> [v3.10+]
Pull watchdog updates from Wim Van Sebroeck:
"This contains:
- addition of the Intel MID watchdog
- removal of W83697HF and W83697UG drivers (code was merged into
w83627hf_wdt driver)
- addition of Armada 375/380 SoC support
- conversion of imx2_wdt to regmap API and to watchdog core API
- lots of other small improvements and fixes"
[ Wim was also tagged by gmail as a spammer, but not delayed by days
unlike Ben ]
* git://www.linux-watchdog.org/linux-watchdog: (25 commits)
x86: intel-mid: add watchdog platform code for Merrifield
watchdog: add Intel MID watchdog driver support
watchdog: sp805: Set watchdog_device->timeout from ->set_timeout()
booke/watchdog: refine and clean up the codes
watchdog: iop_wdt only builds for mach-iop13xx
watchdog: Remove drivers for W83697HF and W83697UG
watchdog: w83627hf_wdt: Add early_disable module parameter
ARM: mvebu: Add A375/A380 watchdog binding documentation
watchdog: orion: Add Armada 375/380 SoC support
watchdog: orion: Introduce per-SoC enabled() function
watchdog: orion: Introduce per-SoC stop() function
watchdog: orion: Remove unneeded atomic access
watchdog: orion: Introduce a SoC-specific RSTOUT mapping
watchdog: orion: Move the register ioremap'ing to its own function
watchdog: xilinx: Make of_device_id array const
watchdog: imx2_wdt: convert to watchdog core api
watchdog: imx2_wdt: convert to use regmap API.
watchdog: imx2_wdt: Sort the header files alphabetically
watchdog: ath79_wdt: switch to clk_prepare/clk_disable
watchdog: ath79_wdt: avoid spurious restarts on AR934x
...
Pull powerpc updates from Ben Herrenschmidt:
"Here is the bulk of the powerpc changes for this merge window. It got
a bit delayed in part because I wasn't paying attention, and in part
because I discovered I had a core PCI change without a PCI maintainer
ack in it. Bjorn eventually agreed it was ok to merge it though we'll
probably improve it later and I didn't want to rebase to add his ack.
There is going to be a bit more next week, essentially fixes that I
still want to sort through and test.
The biggest item this time is the support to build the ppc64 LE kernel
with our new v2 ABI. We previously supported v2 userspace but the
kernel itself was a tougher nut to crack. This is now sorted mostly
thanks to Anton and Rusty.
We also have a fairly big series from Cedric that add support for
64-bit LE zImage boot wrapper. This was made harder by the fact that
traditionally our zImage wrapper was always 32-bit, but our new LE
toolchains don't really support 32-bit anymore (it's somewhat there
but not really "supported") so we didn't want to rely on it. This
meant more churn that just endian fixes.
This brings some more LE bits as well, such as the ability to run in
LE mode without a hypervisor (ie. under OPAL firmware) by doing the
right OPAL call to reinitialize the CPU to take HV interrupts in the
right mode and the usual pile of endian fixes.
There's another series from Gavin adding EEH improvements (one day we
*will* have a release with less than 20 EEH patches, I promise!).
Another highlight is the support for the "Split core" functionality on
P8 by Michael. This allows a P8 core to be split into "sub cores" of
4 threads which allows the subcores to run different guests under KVM
(the HW still doesn't support a partition per thread).
And then the usual misc bits and fixes ..."
[ Further delayed by gmail deciding that BenH is a dirty spammer.
Google knows. ]
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (155 commits)
powerpc/powernv: Add missing include to LPC code
selftests/powerpc: Test the THP bug we fixed in the previous commit
powerpc/mm: Check paca psize is up to date for huge mappings
powerpc/powernv: Pass buffer size to OPAL validate flash call
powerpc/pseries: hcall functions are exported to modules, need _GLOBAL_TOC()
powerpc: Exported functions __clear_user and copy_page use r2 so need _GLOBAL_TOC()
powerpc/powernv: Set memory_block_size_bytes to 256MB
powerpc: Allow ppc_md platform hook to override memory_block_size_bytes
powerpc/powernv: Fix endian issues in memory error handling code
powerpc/eeh: Skip eeh sysfs when eeh is disabled
powerpc: 64bit sendfile is capped at 2GB
powerpc/powernv: Provide debugfs access to the LPC bus via OPAL
powerpc/serial: Use saner flags when creating legacy ports
powerpc: Add cpu family documentation
powerpc/xmon: Fix up xmon format strings
powerpc/powernv: Add calls to support little endian host
powerpc: Document sysfs DSCR interface
powerpc: Fix regression of per-CPU DSCR setting
powerpc: Split __SYSFS_SPRSETUP macro
arch: powerpc/fadump: Cleaning up inconsistent NULL checks
...
Basically, this patch does the following:
1. Move the codes of parsing boot parameters from setup-common.c
to driver. In this way, code reader can know directly that
there are boot parameters that can change the timeout.
2. Make boot parameter 'booke_wdt_period' effective.
currently, when driver is loaded, default timeout is always
being used in stead of booke_wdt_period.
3. Wrap up the watchdog timeout in device struct and clean up
unnecessary codes.
Signed-off-by: Tang Yuantian <yuantian.tang@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Li Yang <leoli@freescale.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
As of commit 799fef0612 ("powerpc: Use generic idle loop"), this
applies to arch_cpu_idle() instead of cpu_idle().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is better not to think about compute capacity as being equivalent
to "CPU power". The upcoming "power aware" scheduler work may create
confusion with the notion of energy consumption if "power" is used too
liberally.
Let's rename the following feature flags since they do relate to capacity:
SD_SHARE_CPUPOWER -> SD_SHARE_CPUCAPACITY
ARCH_POWER -> ARCH_CAPACITY
NONTASK_POWER -> NONTASK_CAPACITY
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Morten Rasmussen <morten.rasmussen@arm.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: linaro-kernel@lists.linaro.org
Cc: Andy Fleming <afleming@freescale.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Link: http://lkml.kernel.org/n/tip-e93lpnxb87owfievqatey6b5@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The pseries platform code unconditionally overrides
memory_block_size_bytes regardless of the running platform.
Create a ppc_md hook that so each platform can choose to
do what it wants.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When eeh is not enabled, and hotplug two pci devices on the same bus, eeh
related sysfs would be added twice for the first added pci device. Since the
eeh_dev is not created when eeh is not enabled.
This patch adds the check, if eeh is not enabled, eeh sysfs will not be
created.
After applying this patch, following warnings are reduced:
sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:00.0/eeh_mode'
sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:00.0/eeh_config_addr'
sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:00.0/eeh_pe_config_addr'
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We had a mix & match of flags used when creating legacy ports
depending on where we found them in the device-tree. Among others
we were missing UPF_SKIP_TEST for some kind of ISA ports which is
a problem as quite a few UARTs out there don't support the loopback
test (such as a lot of BMCs).
Let's pick the set of flags used by the SoC code and generalize it
which means autoconf, no loopback test, irq maybe shared and fixed
port.
Sending to stable as the lack of UPF_SKIP_TEST is breaking
serial on some machines so I want this back into distros
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: stable@vger.kernel.org
- Another round of clean-up of FDT related code in architecture code.
This removes knowledge of internal FDT details from most architectures
except powerpc.
- Conversion of kernel's custom FDT parsing code to use libfdt.
- DT based initialization for generic serial earlycon. The introduction
of generic serial earlycon support went in thru tty tree.
- Improve the platform device naming for DT probed devices to ensure
unique naming and use parent names instead of a global index.
- Fix a race condition in of_update_property.
- Unify the various linker section OF match tables and fix several
function prototype errors.
- Update platform_get_irq_byname to work in deferred probe cases.
- 2 binding doc updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTjzgyAAoJEMhvYp4jgsXiFsUH/1PMTGo8CyD62VQD5ZKdAoW+
Fq6vCiRQ8assF5i5ZLcW1DqhjtoRaCKYhVbRKa5lj7cZdjlSpacI/qQPrF5Br2Ii
bTE3Ff/AQwipQaz/Bj7HqJCgGwfWK8xdfgW0abKsyXMWDN86Bov/zzeu8apmws0x
H1XjJRgnc/rzM4m9ny6+lss0iq6YL54SuTYNzHR33+Ywxls69SfHXIhCW0KpZcBl
5U3YUOomt40GfO46sxFA4xApAhypEK4oVq7asyiA2ArTZ/c2Pkc9p5CBqzhDLmlq
yioWTwHIISv0q+yMLCuQrVGIsbUDkQyy7RQ15z6U+/e/iGO/M+j3A5yxMc3qOi4=
=Onff
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux into next
Pull DeviceTree updates from Rob Herring:
- Another round of clean-up of FDT related code in architecture code.
This removes knowledge of internal FDT details from most
architectures except powerpc.
- Conversion of kernel's custom FDT parsing code to use libfdt.
- DT based initialization for generic serial earlycon. The
introduction of generic serial earlycon support went in through the
tty tree.
- Improve the platform device naming for DT probed devices to ensure
unique naming and use parent names instead of a global index.
- Fix a race condition in of_update_property.
- Unify the various linker section OF match tables and fix several
function prototype errors.
- Update platform_get_irq_byname to work in deferred probe cases.
- 2 binding doc updates
* tag 'devicetree-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (58 commits)
of: handle NULL node in next_child iterators
of/irq: provide more wrappers for !CONFIG_OF
devicetree: bindings: Document micrel vendor prefix
dt: bindings: dwc2: fix required value for the phy-names property
of_pci_irq: kill useless variable in of_irq_parse_pci()
of/irq: do irq resolution in platform_get_irq_byname()
of: Add a testcase for of_find_node_by_path()
of: Make of_find_node_by_path() handle /aliases
of: Create unlocked version of for_each_child_of_node()
lib: add glibc style strchrnul() variant
of: Handle memory@0 node on PPC32 only
pci/of: Remove dead code
of: fix race between search and remove in of_update_property()
of: Use NULL for pointers
of: Stop naming platform_device using dcr address
of: Ensure unique names without sacrificing determinism
tty/serial: pl011: add DT based earlycon support
of/fdt: add FDT serial scanning for earlycon
of/fdt: add FDT address translation support
serial: earlycon: add DT support
...
was a pretty active cycle for KVM. Changes include:
- a lot of s390 changes: optimizations, support for migration,
GDB support and more
- ARM changes are pretty small: support for the PSCI 0.2 hypercall
interface on both the guest and the host (the latter acked by Catalin)
- initial POWER8 and little-endian host support
- support for running u-boot on embedded POWER targets
- pretty large changes to MIPS too, completing the userspace interface
and improving the handling of virtualized timer hardware
- for x86, a larger set of changes is scheduled for 3.17. Still,
we have a few emulator bugfixes and support for running nested
fully-virtualized Xen guests (para-virtualized Xen guests have
always worked). And some optimizations too.
The only missing architecture here is ia64. It's not a coincidence
that support for KVM on ia64 is scheduled for removal in 3.17.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=j5Od
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm into next
Pull KVM updates from Paolo Bonzini:
"At over 200 commits, covering almost all supported architectures, this
was a pretty active cycle for KVM. Changes include:
- a lot of s390 changes: optimizations, support for migration, GDB
support and more
- ARM changes are pretty small: support for the PSCI 0.2 hypercall
interface on both the guest and the host (the latter acked by
Catalin)
- initial POWER8 and little-endian host support
- support for running u-boot on embedded POWER targets
- pretty large changes to MIPS too, completing the userspace
interface and improving the handling of virtualized timer hardware
- for x86, a larger set of changes is scheduled for 3.17. Still, we
have a few emulator bugfixes and support for running nested
fully-virtualized Xen guests (para-virtualized Xen guests have
always worked). And some optimizations too.
The only missing architecture here is ia64. It's not a coincidence
that support for KVM on ia64 is scheduled for removal in 3.17"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (203 commits)
KVM: add missing cleanup_srcu_struct
KVM: PPC: Book3S PR: Rework SLB switching code
KVM: PPC: Book3S PR: Use SLB entry 0
KVM: PPC: Book3S HV: Fix machine check delivery to guest
KVM: PPC: Book3S HV: Work around POWER8 performance monitor bugs
KVM: PPC: Book3S HV: Make sure we don't miss dirty pages
KVM: PPC: Book3S HV: Fix dirty map for hugepages
KVM: PPC: Book3S HV: Put huge-page HPTEs in rmap chain for base address
KVM: PPC: Book3S HV: Fix check for running inside guest in global_invalidates()
KVM: PPC: Book3S: Move KVM_REG_PPC_WORT to an unused register number
KVM: PPC: Book3S: Add ONE_REG register names that were missed
KVM: PPC: Add CAP to indicate hcall fixes
KVM: PPC: MPIC: Reset IRQ source private members
KVM: PPC: Graciously fail broken LE hypercalls
PPC: ePAPR: Fix hypercall on LE guest
KVM: PPC: BOOK3S: Remove open coded make_dsisr in alignment handler
KVM: PPC: BOOK3S: Always use the saved DAR value
PPC: KVM: Make NX bit available with magic page
KVM: PPC: Disable NX for old magic page using guests
KVM: PPC: BOOK3S: HV: Add mixed page-size support for guest
...
Pull scheduler updates from Ingo Molnar:
"The main scheduling related changes in this cycle were:
- various sched/numa updates, for better performance
- tree wide cleanup of open coded nice levels
- nohz fix related to rq->nr_running use
- cpuidle changes and continued consolidation to improve the
kernel/sched/idle.c high level idle scheduling logic. As part of
this effort I pulled cpuidle driver changes from Rafael as well.
- standardized idle polling amongst architectures
- continued work on preparing better power/energy aware scheduling
- sched/rt updates
- misc fixlets and cleanups"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (49 commits)
sched/numa: Decay ->wakee_flips instead of zeroing
sched/numa: Update migrate_improves/degrades_locality()
sched/numa: Allow task switch if load imbalance improves
sched/rt: Fix 'struct sched_dl_entity' and dl_task_time() comments, to match the current upstream code
sched: Consolidate open coded implementations of nice level frobbing into nice_to_rlimit() and rlimit_to_nice()
sched: Initialize rq->age_stamp on processor start
sched, nohz: Change rq->nr_running to always use wrappers
sched: Fix the rq->next_balance logic in rebalance_domains() and idle_balance()
sched: Use clamp() and clamp_val() to make sys_nice() more readable
sched: Do not zero sg->cpumask and sg->sgp->power in build_sched_groups()
sched/numa: Fix initialization of sched_domain_topology for NUMA
sched: Call select_idle_sibling() when not affine_sd
sched: Simplify return logic in sched_read_attr()
sched: Simplify return logic in sched_copy_attr()
sched: Fix exec_start/task_hot on migrated tasks
arm64: Remove TIF_POLLING_NRFLAG
metag: Remove TIF_POLLING_NRFLAG
sched/idle: Make cpuidle_idle_call() void
sched/idle: Reflow cpuidle_idle_call()
sched/idle: Delay clearing the polling bit
...
On LPAR guest systems Linux enables the shadow SLB to indicate to the
hypervisor a number of SLB entries that always have to be available.
Today we go through this shadow SLB and disable all ESID's valid bits.
However, pHyp doesn't like this approach very much and honors us with
fancy machine checks.
Fortunately the shadow SLB descriptor also has an entry that indicates
the number of valid entries following. During the lifetime of a guest
we can just swap that value to 0 and don't have to worry about the
SLB restoration magic.
While we're touching the code, let's also make it more readable (get
rid of rldicl), allow it to deal with a dynamic number of bolted
SLB entries and only do shadow SLB swizzling on LPAR systems.
Signed-off-by: Alexander Graf <agraf@suse.de>
We get an array of instructions from the hypervisor via device tree that
we write into a buffer that gets executed whenever we want to make an
ePAPR compliant hypercall.
However, the hypervisor passes us these instructions in BE order which
we have to manually convert to LE when we want to run them in LE mode.
With this fixup in place, I can successfully run LE kernels with KVM
PV enabled on PR KVM.
Signed-off-by: Alexander Graf <agraf@suse.de>
Use make_dsisr instead of open coding it. This also have
the added benefit of handling alignment interrupt on additional
instructions.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Because old kernels enable the magic page and then choke on NXed trampoline
code we have to disable NX by default in KVM when we use the magic page.
However, since commit b18db0b8 we have successfully fixed that and can now
leave NX enabled, so tell the hypervisor about this.
Signed-off-by: Alexander Graf <agraf@suse.de>
POWER8 implements a new register called TAR. This register has to be
enabled in FSCR and then from KVM's point of view is mere storage.
This patch enables the guest to use TAR.
Signed-off-by: Alexander Graf <agraf@suse.de>
POWER8 introduced a new interrupt type called "Facility unavailable interrupt"
which contains its status message in a new register called FSCR.
Handle these exits and try to emulate instructions for unhandled facilities.
Follow-on patches enable KVM to expose specific facilities into the guest.
Signed-off-by: Alexander Graf <agraf@suse.de>
The shared (magic) page is a data structure that contains often used
supervisor privileged SPRs accessible via memory to the user to reduce
the number of exits we have to take to read/write them.
When we actually share this structure with the guest we have to maintain
it in guest endianness, because some of the patch tricks only work with
native endian load/store operations.
Since we only share the structure with either host or guest in little
endian on book3s_64 pr mode, we don't have to worry about booke or book3s hv.
For booke, the shared struct stays big endian. For book3s_64 hv we maintain
the struct in host native endian, since it never gets shared with the guest.
For book3s_64 pr we introduce a variable that tells us which endianness the
shared struct is in and route every access to it through helper inline
functions that evaluate this variable.
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch make sure we inherit the LE bit correctly in different case
so that we can run Little Endian distro in PR mode
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
* pci/hotplug:
PCI: cpqphp: Fix possible null pointer dereference
NVMe: Implement PCIe reset notification callback
PCI: Notify driver before and after device reset
* pci/pci_is_bridge:
pcmcia: Use pci_is_bridge() to simplify code
PCI: pciehp: Use pci_is_bridge() to simplify code
PCI: acpiphp: Use pci_is_bridge() to simplify code
PCI: cpcihp: Use pci_is_bridge() to simplify code
PCI: shpchp: Use pci_is_bridge() to simplify code
PCI: rpaphp: Use pci_is_bridge() to simplify code
sparc/PCI: Use pci_is_bridge() to simplify code
powerpc/PCI: Use pci_is_bridge() to simplify code
ia64/PCI: Use pci_is_bridge() to simplify code
x86/PCI: Use pci_is_bridge() to simplify code
PCI: Use pci_is_bridge() to simplify code
PCI: Add new pci_is_bridge() interface
PCI: Rename pci_is_bridge() to pci_has_subordinate()
* pci/virtualization:
PCI: Introduce new device binding path using pci_dev.driver_override
Conflicts:
drivers/pci/pci-sysfs.c
The PPC fixes are important because they fix breakage that is new in 3.15.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=E2fU
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"Small fixes for x86, slightly larger fixes for PPC, and a forgotten
s390 patch. The PPC fixes are important because they fix breakage
that is new in 3.15"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: s390: announce irqfd capability
KVM: x86: disable master clock if TSC is reset during suspend
KVM: vmx: disable APIC virtualization in nested guests
KVM guest: Make pv trampoline code executable
KVM: PPC: Book3S: ifdef on CONFIG_KVM_BOOK3S_32_HANDLER for 32bit
KVM: PPC: Book3S HV: Add missing code for transaction reclaim on guest exit
KVM: PPC: Book3S: HV: make _PAGE_NUMA take effect
Since commit "efcac65 powerpc: Per process DSCR + some fixes (try#4)"
it is no longer possible to set the DSCR on a per-CPU basis.
The old behaviour was to minipulate the DSCR SPR directly but this is no
longer sufficient: the value is quickly overwritten by context switching.
This patch stores the per-CPU DSCR value in a kernel variable rather than
directly in the SPR and it is used whenever a process has not set the DSCR
itself. The sysfs interface (/sys/devices/system/cpu/cpuN/dscr) is unchanged.
Writes to the old global default (/sys/devices/system/cpu/dscr_default)
now set all of the per-CPU values and reads return the last written value.
The new per-CPU default is added to the paca_struct and is used everywhere
outside of sysfs.c instead of the old global default.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Split the __SYSFS_SPRSETUP macro into two parts so that registers requiring
custom read and write functions can use common code for their show and store
functions.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cleaning up inconsistent NULL checks.
There is otherwise a risk of a possible null pointer dereference.
Was largely found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
To support split core we need to change the check in __cpu_up() that
determines if a cpu is allowed to come online.
Currently we refuse to online cpus which are not the primary thread
within their core.
On POWER8 with split core support this check needs to instead refuse to
online cpus which are not the primary thread within their *sub* core.
On POWER7 and other systems that do not support split core,
threads_per_subcore == threads_per_core and so the check is equivalent.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On POWER8 we have a new concept of a subcore. This is what happens when
you take a regular core and split it. A subcore is a grouping of two or
four SMT threads, as well as a handfull of SPRs which allows the subcore
to appear as if it were a core from the point of view of a guest.
Unlike threads_per_core which is fixed at boot, threads_per_subcore can
change while the system is running. Most code will not want to use
threads_per_subcore.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
To support split core we need to be able to force all secondaries into
nap, so the core can detect they are idle and do an unsplit.
Currently power7_nap() will return without napping if there is an irq
pending. We want to ignore the pending irq and nap anyway, we will deal
with the interrupt later.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As part of the support for split core on POWER8, we want to be able to
block splitting of the core while KVM VMs are active.
The logic to do that would be exactly the same as the code we currently
have for inhibiting onlining of secondaries.
Instead of adding an identical mechanism to block split core, rework the
secondary inhibit code to be a "HV KVM is active" check. We can then use
that in both the cpu hotplug code and the upcoming split core code.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Alexander Graf <agraf@suse.de>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Based off 3bccd996 for ia64, convert powerpc to use the generic per-CPU
topology tracking, specifically:
initialize per cpu numa_node entry in start_secondary
remove the powerpc cpu_to_node()
define CONFIG_USE_PERCPU_NUMA_NODE_ID if NUMA
Signed-off-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we try to perform a kexec when the machine is in ST (Single-Threaded) mode
(ppc64_cpu --smt=off), the kexec operation doesn't succeed properly, and we
get the following messages during boot:
[ 0.089866] POWER8 performance monitor hardware support registered
[ 0.089985] power8-pmu: PMAO restore workaround active.
[ 5.095419] Processor 1 is stuck.
[ 10.097933] Processor 2 is stuck.
[ 15.100480] Processor 3 is stuck.
[ 20.102982] Processor 4 is stuck.
[ 25.105489] Processor 5 is stuck.
[ 30.108005] Processor 6 is stuck.
[ 35.110518] Processor 7 is stuck.
[ 40.113369] Processor 9 is stuck.
[ 45.115879] Processor 10 is stuck.
[ 50.118389] Processor 11 is stuck.
[ 55.120904] Processor 12 is stuck.
[ 60.123425] Processor 13 is stuck.
[ 65.125970] Processor 14 is stuck.
[ 70.128495] Processor 15 is stuck.
[ 75.131316] Processor 17 is stuck.
Note that only the sibling threads are stuck, while the primary threads (0, 8,
16 etc) boot just fine. Looking closer at the previous step of kexec, we observe
that kexec tries to wakeup (bring online) the sibling threads of all the cores,
before performing kexec:
[ 9464.131231] Starting new kernel
[ 9464.148507] kexec: Waking offline cpu 1.
[ 9464.148552] kexec: Waking offline cpu 2.
[ 9464.148600] kexec: Waking offline cpu 3.
[ 9464.148636] kexec: Waking offline cpu 4.
[ 9464.148671] kexec: Waking offline cpu 5.
[ 9464.148708] kexec: Waking offline cpu 6.
[ 9464.148743] kexec: Waking offline cpu 7.
[ 9464.148779] kexec: Waking offline cpu 9.
[ 9464.148815] kexec: Waking offline cpu 10.
[ 9464.148851] kexec: Waking offline cpu 11.
[ 9464.148887] kexec: Waking offline cpu 12.
[ 9464.148922] kexec: Waking offline cpu 13.
[ 9464.148958] kexec: Waking offline cpu 14.
[ 9464.148994] kexec: Waking offline cpu 15.
[ 9464.149030] kexec: Waking offline cpu 17.
Instrumenting this piece of code revealed that the cpu_up() operation actually
fails with -EBUSY. Thus, only the primary threads of all the cores are online
during kexec, and hence this is a sure-shot receipe for disaster, as explained
in commit e8e5c2155b (powerpc/kexec: Fix orphaned offline CPUs across kexec),
as well as in the comment above wake_offline_cpus().
It turns out that cpu_up() was returning -EBUSY because the variable
'cpu_hotplug_disabled' was set to 1; and this disabling of CPU hotplug was done
by migrate_to_reboot_cpu() inside kernel_kexec().
Now, migrate_to_reboot_cpu() was originally written with the assumption that
any further code will not need to perform CPU hotplug, since we are anyway in
the reboot path. However, kexec is clearly not such a case, since we depend on
onlining CPUs, atleast on powerpc.
So re-enable cpu-hotplug after returning from migrate_to_reboot_cpu() in the
kexec path, to fix this regression in kexec on powerpc.
Also, wrap the cpu_up() in powerpc kexec code within a WARN_ON(), so that we
can catch such issues more easily in the future.
Fixes: c97102ba96 (kexec: migrate to reboot cpu)
Cc: stable@vger.kernel.org
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
<<
Highlights include a few new boards, a device tree binding for CCF
(including backwards-compatible device tree updates to distinguish
incompatible versions), and some fixes.
>>
Use pci_is_bridge() to simplify code. No functional change.
Requires: 326c1cdae7 PCI: Rename pci_is_bridge() to pci_has_subordinate()
Requires: 1c86438c94 PCI: Add new pci_is_bridge() interface
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We get an array of instructions from the hypervisor via device tree that
we write into a buffer that gets executed whenever we want to make an
ePAPR compliant hypercall.
However, the hypervisor passes us these instructions in BE order which
we have to manually convert to LE when we want to run them in LE mode.
With this fixup in place, I can successfully run LE kernels with KVM
PV enabled on PR KVM.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This warning can be seen in allyesconfig, and was introduced by commit
f9eb581c63b2acce827570e105205c0789360650 "powerpc: fix build of
epapr_paravirt on 64-bit book3s".
Signed-off-by: Scott Wood <scottwood@freescale.com>
This fixes an allyesconfig build break introduced by commit
7762b1ed7aaee223230793fcee80672e2e3aa7a8 "powerpc: move epapr paravirt
init of power_save to an initcall".
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Stuart Yoder <stuart.yoder@freescale.com>
some restructuring of epapr paravirt init resulted in
ppc_md.power_save being set, and then overwritten to
NULL during machine_init. This patch splits the
initialization of ppc_md.power_save out into a postcore
init call.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
A simple patch which was supposed to swap r12 and r11 also
inexplicably changed the offset by two bytes. This instruction
(to load r2) isn't used in LE, so it wasn't noticed.
Fixes: b1ce369e82 ("powerpc: modules: use r12 for stub jump address.)
Reported-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Tested-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, on 8641D, which doesn't set CONFIG_HAVE_HW_BREAKPOINT
we get the following splat:
BUG: using smp_processor_id() in preemptible [00000000] code: login/1382
caller is set_breakpoint+0x1c/0xa0
CPU: 0 PID: 1382 Comm: login Not tainted 3.15.0-rc3-00041-g2aafe1a4d451 #1
Call Trace:
[decd5d80] [c0008dc4] show_stack+0x50/0x158 (unreliable)
[decd5dc0] [c03c6fa0] dump_stack+0x7c/0xdc
[decd5de0] [c01f8818] check_preemption_disabled+0xf4/0x104
[decd5e00] [c00086b8] set_breakpoint+0x1c/0xa0
[decd5e10] [c00d4530] flush_old_exec+0x2bc/0x588
[decd5e40] [c011c468] load_elf_binary+0x2ac/0x1164
[decd5ec0] [c00d35f8] search_binary_handler+0xc4/0x1f8
[decd5ef0] [c00d4ee8] do_execve+0x3d8/0x4b8
[decd5f40] [c001185c] ret_from_syscall+0x0/0x38
--- Exception: c01 at 0xfeee554
LR = 0xfeee7d4
The call path in this case is:
flush_thread
--> set_debug_reg_defaults
--> set_breakpoint
--> __get_cpu_var
Since preemption is enabled in the cleanup of flush thread, and
there is no need to disable it, introduce the distinction between
set_breakpoint and __set_breakpoint, leaving only the flush_thread
instance as the current user of set_breakpoint.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
None of the callers check the return value, so it might as
well not have one at all.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 7f52a526f ("powerpc/eeh: Allow to disable EEH") caused
following build error with "celleb_defconfig" as being catched
by Mikey on linux-next.
arch/powerpc/kernel/eeh.c: In function 'eeh_init_proc':
arch/powerpc/kernel/eeh.c:1173:37: error: 'powerpc_debugfs_root' \
undeclared (first use in this function)
arch/powerpc/kernel/eeh.c:1173:37: note: each undeclared identifier \
is reported only once for each function it appears in
Reported-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Merge "merge" branch to get two fairly important bug fixes:
powerpc/powernv: Reset root port in firmware
powerpc: irq work racing with timer interrupt can result in timer interrupt
This request includes a few bug fixes that really shouldn't wait for the next
release.
It fixes KVM on 32bit PowerPC when built as module. It also fixes the PV KVM
acceleration when NX gets honored by the host. Furthermore we fix transactional
memory support and numa support on HV KVM.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQIcBAABAgAGBQJTcKFaAAoJECszeR4D/txg7qYP/RX3V32i2zQYH2NpjQrDCwtY
Wur+CQrn/VA6xhtTK1rT2zH5rNFLt6ClhtxCMkZFfBdUE4sHi3OTlEdcvXBZjbls
JqQ/7lBkUPN8pTpz2NHP9gvH7g6v07EruysRQNa/JZMzlwhpzWk8D7yXakaCPNY/
JZRgVTrfKnhQ8OtXt48Bp4EmEKllbNqi9kNN7dewD2dEb3fAco3Jpk6WoeG+1f0o
jv3NmeTsp87KaRpjvDzPb7iCe6PA7GVqvJIQpir3Rpk2Kpx0yj58AfacF+f72GOf
CPlJGepiumJCaANhV6dbvtS49vaiiAnSvbqCil2USNl0LIGWQXdSjs5lztEuiMyr
tAav0YSVpnIcw0HJxXug/M31VwfRjYCX3hnCCIOd3Xj2jgAqwD+Lo95uUrRGJ9TP
75zKh8E093tOXIC9CyMaiYajpFMUrCSMgnpJ+7fpeHiyigB6yc8juFxahIHsw8q1
NgHggroJm6QNIm8JSY/tG/YET4AT7H4ZetGP8MeeRUg0TpqQXvYpkMGB8YDouaBA
XzxjwyTq57BOYgLGExnwW3Jj0kbqVY+ts0aDGQVGrl5YFzooGqrQ61CRmwG5BvI8
sou3l6TJ2ng8qrc7Maw9MHca1QB3mtXD7I26T/QEfQm9NLRTTqJyaxH5J1q9siRI
PpHVE5FKnmWPNr8JlxtC
=t2S+
-----END PGP SIGNATURE-----
Merge tag 'signed-for-3.15' of git://github.com/agraf/linux-2.6 into kvm-master
Patch queue for 3.15 - 2014-05-12
This request includes a few bug fixes that really shouldn't wait for the next
release.
It fixes KVM on 32bit PowerPC when built as module. It also fixes the PV KVM
acceleration when NX gets honored by the host. Furthermore we fix transactional
memory support and numa support on HV KVM.
I am seeing an issue where a CPU running perf eventually hangs.
Traces show timer interrupts happening every 4 seconds even
when a userspace task is running on the CPU. /proc/timer_list
also shows pending hrtimers have not run in over an hour,
including the scheduler.
Looking closer, decrementers_next_tb is getting set to
0xffffffffffffffff, and at that point we will never take
a timer interrupt again.
In __timer_interrupt() we set decrementers_next_tb to
0xffffffffffffffff and rely on ->event_handler to update it:
*next_tb = ~(u64)0;
if (evt->event_handler)
evt->event_handler(evt);
In this case ->event_handler is hrtimer_interrupt. This will eventually
call back through the clockevents code with the next event to be
programmed:
static int decrementer_set_next_event(unsigned long evt,
struct clock_event_device *dev)
{
/* Don't adjust the decrementer if some irq work is pending */
if (test_irq_work_pending())
return 0;
__get_cpu_var(decrementers_next_tb) = get_tb_or_rtc() + evt;
If irq work came in between these two points, we will return
before updating decrementers_next_tb and we never process a timer
interrupt again.
This looks to have been introduced by 0215f7d8c5 (powerpc: Fix races
with irq_work). Fix it by removing the early exit and relying on
code later on in the function to force an early decrementer:
/* We may have raced with new irq work */
if (test_irq_work_pending())
set_dec(1);
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org # 3.14+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This series adds support for building the powerpc 64-bit
LE kernel using the new ABI v2. We already supported
running ABI v2 userspace programs but this adds support
for building the kernel itself using the new ABI.
Move the devspec OF attribute to PCI common code's set of device attributes
since it's not architecture dependent. As a side effect microblaze and
powerpc no longer need to use pcibios_add_platform_entries().
[bhelgaas: fold in #include for compile error]
Link: https://lkml.kernel.org/r/alpine.LFD.2.11.1404141101500.1529@denkbrett
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With libfdt support, we can take advantage of helper accessors in libfdt
for accessing the FDT header data. This makes the code more readable and
makes the FDT blob structure more opaque to the kernel. This also
prepares for removing struct boot_param_header completely.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Tested-by: Grant Likely <grant.likely@linaro.org>
Tested-by: Stephen Chivers <schivers@csc.com>
Move the /memreserve/ processing and dtb memory reservations into
early_init_fdt_scan_reserved_mem. This converts arm, arm64, and powerpc
as they are the only users of early_init_fdt_scan_reserved_mem.
memblock_reserve is safe to call on the same region twice, so the
reservation check for the dtb in powerpc 32-bit reservations is safe to
remove.
Signed-off-by: Rob Herring <robh@kernel.org>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Tested-by: Grant Likely <grant.likely@linaro.org>
Tested-by: Stephen Chivers <schivers@csc.com>
Both powerpc and microblaze have the same FDT blob in debugfs feature.
Move this to common location and remove the powerpc and microblaze
implementations. This feature could become more useful when FDT
overlay support is added.
This changes the path of the blob from "$arch/flat-device-tree" to
"device-tree/flat-device-tree".
Signed-off-by: Rob Herring <robh@kernel.org>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Tested-by: Grant Likely <grant.likely@linaro.org>
Tested-by: Stephen Chivers <schivers@csc.com>
Make of_get_flat_dt_prop arguments compatible with libfdt fdt_getprop
call in preparation to convert FDT code to use libfdt. Make the return
value const and the property length ptr type an int.
Signed-off-by: Rob Herring <robh@kernel.org>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Grant Likely <grant.likely@linaro.org>
Tested-by: Stephen Chivers <schivers@csc.com>
The call to early_init_fdt_scan_reserved_mem will be skipped if
reserved-ranges is not found. Move the call earlier so that it is called
unconditionally.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Tested-by: Stephen Chivers <schivers@csc.com>
Unaligned stores take alignment exceptions on POWER7 running in little-endian.
This is a dumb little-endian base memcpy that prevents unaligned stores.
Once booted the feature fixup code switches over to the VMX copy loops
(which are already endian safe).
The question is what we do before that switch over. The base 64bit
memcpy takes alignment exceptions on POWER7 so we can't use it as is.
Fixing the causes of alignment exception would slow it down, because
we'd need to ensure all loads and stores are aligned either through
rotate tricks or bytewise loads and stores. Either would be bad for
all other 64bit platforms.
[ I simplified the loop a bit - Anton ]
Signed-off-by: Philippe Bergheaud <felix@linux.vnet.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Our PV guest patching code assembles chunks of instructions on the fly when it
encounters more complicated instructions to hijack. These instructions need
to live in a section that we don't mark as non-executable, as otherwise we
fault when jumping there.
Right now we put it into the .bss section where it automatically gets marked
as non-executable. Add a check to the NX setting function to ensure that we
leave these particular pages executable.
Signed-off-by: Alexander Graf <agraf@suse.de>
If we do a treclaim and we are not in TM suspend mode, it results in a TM bad
thing (ie. a 0x700 program check). Similarly if we do a trechkpt and we have
an active transaction or TEXASR Failure Summary (FS) is not set, we also take a
TM bad thing.
This should never happen, but if it does (ie. a kernel bug), the cause is
almost impossible to debug as the GPR state is mostly userspace and hence we
don't get a call chain.
This adds some checks in these cases case a BUG_ON() (in asm) in case we ever
hit these cases. It moves the register saving around to preserve r1 till later
also.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We save r1 to the scratch SPR and restore it from there after the trechkpt so
saving r1 to the paca is not needed.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, the code in setup-common.c for powerpc assumes that all
clock rates are same in a smp system. This value is cached in the
variable named ppc_proc_freq and is the value that is reported in
/proc/cpuinfo.
However on the PowerNV platform, the clock rate is same only across
the threads of the same core. Hence the value that is reported in
/proc/cpuinfo is incorrect on PowerNV platforms. We need a better way
to query and report the correct value of the processor clock in
/proc/cpuinfo.
The patch achieves this by creating a machdep_call named
get_proc_freq() which is expected to returns the frequency in Hz. The
code in show_cpuinfo() can invoke this method to display the correct
clock rate on platforms that have implemented this method. On the
other powerpc platforms it can use the value cached in ppc_proc_freq.
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch updates the implementation of pci_process_bridge_OF_ranges to use
the of_pci_range_parser helpers.
Signed-off-by: Andrew Murray <amurray@embedded-bits.co.uk>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds support to legacy serial for
UARTS with shifted registers.
The MVME5100 Single Board Computer is a PowerPC platform
that has 16550 style UARTS with register addresses that are
16 bytes apart (shifted by 4).
Commit 309257484c
"powerpc: Cleanup udbg_16550 and add support for LPC PIO-only UARTs"
added support to udbg_16550 for shifted registers by adding a "stride"
parameter to the initialisation operations for Programmed IO and
Memory Mapped IO.
As a consequence it is now possible to use the services of legacy serial
to provide early serial console messages for the MVME5100.
An added benefit of this is that the serial console will always be
"ttyS0" irrespective of whether the computer is fitted with extra
PCI 8250 interface boards or not.
I have tested this patch using the four PowerPC platforms available to me:
MVME5100 - shifted registers,
SAM440EP - unshifted registers,
MPC8349 - unshifted registers,
MVME4100 - unshifted registers.
Signed-off-by: Stephen Chivers <schivers@csc.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Function early_init_dt_scan_fw_dump() is called to scan the device
tree for fdump properties under node "rtas". Any one of them is
invalid, we can stop scanning the device tree early by returning
"1". It would save a bit time during boot.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When PCI_ERS_RESULT_CAN_RECOVER returned from device drivers, the
EEH core should enable I/O and DMA for the affected PE. However,
it was missed to have DMA enabled in eeh_handle_normal_event().
Besides, the frozen state of the affected PE should be cleared
after successful recovery, but we didn't.
The patch fixes both of the issues as above.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The problem was initially reported by Wendy who tried pass through
IPR adapter, which was connected to PHB root port directly, to KVM
based guest. When doing that, pci_reset_bridge_secondary_bus() was
called by VFIO driver and linkDown was detected by the root port.
That caused all PEs to be frozen.
The patch fixes the issue by routing the reset for the secondary bus
of root port to underly firmware. For that, one more weak function
pci_reset_secondary_bus() is introduced so that the individual platforms
can override that and do specific reset for bridge's secondary bus.
Reported-by: Wendy Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Basically, we have 3 types of resets to fulfil PE reset: fundamental,
hot and PHB reset. For the later 2 cases, we need PCI bus reset hold
and settlement delay as specified by PCI spec. PowerNV and pSeries
platforms are running on top of different firmware and some of the
delays have been covered by underly firmware (PowerNV).
The patch makes the delays unified to be done in backend, instead of
EEH core.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The issue was detected in a bit complicated test case where
we have multiple hierarchical PEs shown as following figure:
+-----------------+
| PE#3 p2p#0 |
| p2p#1 |
+-----------------+
|
+-----------------+
| PE#4 pdev#0 |
| pdev#1 |
+-----------------+
PE#4 (have 2 PCI devices) is the child of PE#3, which has 2 p2p
bridges. We accidentally had less-known scenario: PE#4 was removed
permanently from the system because of permanent failure (e.g.
exceeding the max allowd failure times in last hour), then we detects
EEH errors on PE#3 and tried to recover it. However, eeh_dev instances
for pdev#0/1 were not detached from PE#4, which was still connected to
PE#3. All of that was because of the fact that we rely on count-based
pcibios_release_device(), which isn't reliable enough. When doing
recovery for PE#3, we still apply hotplug on PE#4 and pdev#0/1, which
are not valid any more. Eventually, we run into kernel crash.
The patch fixes above issue from two aspects. For unplug, we simply
skip those permanently removed PE, whose state is (EEH_PE_STATE_ISOLATED
&& !EEH_PE_STATE_RECOVERING) and its frozen count should be greater
than EEH_MAX_ALLOWED_FREEZES. For plug, we marked all permanently
removed EEH devices with EEH_DEV_REMOVED and return 0xFF's on read
its PCI config so that PCI core will omit them.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch introduces bootarg "eeh=off" to disable EEH functinality.
Also, it creates /sys/kerenl/debug/powerpc/eeh_enable to disable
or enable EEH functionality. By default, we have the functionality
enabled.
For PowerNV platform, we will restore to have the conventional
mechanism of clearing frozen PE during PCI config access if we're
going to disable EEH functionality. Conversely, we will rely on
EEH for error recovery.
The patch also fixes the issue that we missed to cover the case
of disabled EEH functionality in function ioda_eeh_event(). Those
events driven by interrupt should be cleared to avoid endless
reporting.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There're 2 EEH subsystem variables: eeh_subsystem_enabled and
eeh_probe_mode. We needn't maintain 2 variables and we can just
have one variable and introduce different flags. The patch also
introduces additional flag EEH_FORCE_DISABLE, which will be used
to disable EEH subsystem via boot parameter ("eeh=off") in future.
Besides, the patch also introduces flag EEH_ENABLED, which is
changed to disable or enable EEH functionality on the fly through
debugfs entry in future.
With the patch applied, the creteria to check the enabled EEH
functionality is changed to:
!EEH_FORCE_DISABLED && EEH_ENABLED : Enabled
Other cases : Disabled
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When calling into eeh_gather_pci_data() on pSeries platform, we
possiblly don't have pci_dev instance yet, but eeh_dev is always
ready. So we use cached capability from eeh_dev instead of pci_dev
for log dump there. In order to keep things unified, we also cache
PCI capability positions to eeh_dev for PowerNV as well.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch replaces printk(KERN_WARNING ...) with pr_warn() in the
function eeh_gather_pci_data().
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have suffered recrusive frozen PE a lot, which was caused
by IO accesses during the PE reset. Ben came up with the good
idea to keep frozen PE until recovery (BAR restore) gets done.
With that, IO accesses during PE reset are dropped by hardware
and wouldn't incur the recrusive frozen PE any more.
The patch implements the idea. We don't clear the frozen state
until PE reset is done completely. During the period, the EEH
core expects unfrozen state from backend to keep going. So we
have to reuse EEH_PE_RESET flag, which has been set during PE
reset, to return normal state from backend. The side effect is
we have to clear frozen state for towice (PE reset and clear it
explicitly), but that's harmless.
We have some limitations on pHyp. pHyp doesn't allow to enable
IO or DMA for unfrozen PE. So we don't enable them on unfrozen PE
in eeh_pci_enable(). We have to enable IO before grabbing logs on
pHyp. Otherwise, 0xFF's is always returned from PCI config space.
Also, we had wrong return value from eeh_pci_enable() for
EEH_OPT_THAW_DMA case. The patch fixes it too.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We've observed multiple PE reset failures because of PCI-CFG
access during that period. Potentially, some device drivers
can't support EEH very well and they can't put the device to
motionless state before PE reset. So those device drivers might
produce PCI-CFG accesses during PE reset. Also, we could have
PCI-CFG access from user space (e.g. "lspci"). Since access to
frozen PE should return 0xFF's, we can block PCI-CFG access
during the period of PE reset so that we won't get recrusive EEH
errors.
The patch adds flag EEH_PE_RESET, which is kept during PE reset.
The PowerNV/pSeries PCI-CFG accessors reuse the flag to block
PCI-CFG accordingly.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When doing PE reset, EEH_PE_ISOLATED is cleared unconditionally.
However, We should remove that if the PE reset has cleared the
frozen state successfully. Otherwise, the flag should be kept.
The patch fixes the issue.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The PE state (for eeh_pe instance) EEH_PE_PHB_DEAD is duplicate to
EEH_PE_ISOLATED. Originally, those PHBs (PHB PE) with EEH_PE_PHB_DEAD
would be removed from the system. However, it's safe to replace
that with EEH_PE_ISOLATED.
The patch also clear EEH_PE_RECOVERING after fenced PHB has been handled,
either failure or success. It makes the PHB PE state consistent with:
PHB functions normally NONE
PHB has been removed EEH_PE_ISOLATED
PHB fenced, recovery in progress EEH_PE_ISOLATED | RECOVERING
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
module_init should return 0 or a negative errno.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit aac416fc38 (lkdtm: flush icache and report actions) calls
flush_icache_range from a module. It's exported on most architectures
that implement it, but not on powerpc. This patch exports it to fix
the module link failure.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
__ftrace_make_call assumed ABIv1 TOC stack offsets, so it
broke on ABIv2.
While we are here, we can simplify the instruction modification
code. Since we always update one instruction there is no need to
probe_kernel_write and flush_icache_range, just use patch_branch.
Signed-off-by: Anton Blanchard <anton@samba.org>
Now we have is_module_trampoline() and module_trampoline_target()
we can remove a bunch of intimate kernel module trampoline
knowledge from ftrace.
Signed-off-by: Anton Blanchard <anton@samba.org>
ftrace has way too much knowledge of our kernel module trampoline
layout hidden inside it. Create module_trampoline_target() that gives
the target address of a kernel module trampoline.
Signed-off-by: Anton Blanchard <anton@samba.org>
ftrace has way too much knowledge of our kernel module trampoline
layout hidden inside it. Create is_module_trampoline() that can
abstract this away inside the module loader code.
Signed-off-by: Anton Blanchard <anton@samba.org>
When testing the ftrace function tracer, I realised that ftrace_caller
and mcount are called from modules and they both call into C, therefore
they need the ABIv2 global entry point to establish r2.
Signed-off-by: Anton Blanchard <anton@samba.org>
ELFv2 doesn't use function descriptors, because it doesn't need to
load a new r2 when calling into a function. On the other hand, you're
supposed to use a local entry point for R_PPC_REL24 branches.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
In ELFv2, r12 is supposed to equal to PC on entry to a function.
Our stubs use r11, so change swap that with r12.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
ELFv2 doesn't use function descriptors, so we don't expect symbols to
start with ".". But because depmod and modpost strip ".", and we have
the special symbol ".TOC.", we still need to do it.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The new ELF ABI tends to use R_PPC64_REL16_LO and R_PPC64_REL16_HA
relocations (PC-relative), so implement them.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The kernel resolved the '.TOC.' to a fake symbol, so we need to fix it up
to point to our .toc section plus 0x8000.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
For the ELFv2 ABI, powerpc introduces a magic symbol ".TOC.". If we
don't create a CRC for it (minus the leading ".", since we strip that)
we get a modpost warning about missing CRC and the CRC array seems to
be displaced by 1 so other CRCs mismatch too.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
For the ELFv2 ABI, powerpc introduces a magic symbol ".TOC.". depmod
then complains that this doesn't resolve (so does modpost, but we could
easily fix that). To export this, we need to use asm.
modpost and depmod both strip "." from symbols for the old PPC64 ELFv1
ABI, so we actually export a "TOC.".
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
There is no need to put a function descriptor in
__secondary_hold_spinloop. Use ppc_function_entry to get the
instruction address and put it in __secondary_hold_spinloop instead.
Also fix an issue where we assumed cur_cpu_spec held a function
descriptor.
Signed-off-by: Anton Blanchard <anton@samba.org>
Change how we setup registers for ret_from_kernel_thread. In
ABIv1, instead of passing a function descriptor in, dereference
it and pass the target in directly.
Use ppc_global_function_entry to get it right on both ABIv1 and ABIv2.
Signed-off-by: Anton Blanchard <anton@samba.org>
To establish addressability quickly, ABIv2 requires the target
address of the function being called to be in r12. Fix a number of
places in assembly code that we do indirect function calls.
We need to avoid function descriptors on ABIv2 too.
Signed-off-by: Anton Blanchard <anton@samba.org>
There are a few places we have to use dot symbols with the
current ABI - the syscall table and the kvm hcall table.
Wrap both of these with a new macro called DOTSYM so it will
be easy to transition away from dot symbols in a future ABI.
Signed-off-by: Anton Blanchard <anton@samba.org>
STD_EXCEPTION_COMMON, STD_EXCEPTION_COMMON_ASYNC and
MASKABLE_EXCEPTION branch to the handler, so we can remove
the explicit dot symbol and binutils will do the right thing.
Signed-off-by: Anton Blanchard <anton@samba.org>
There is no need to create a function descriptor for the system call
table. By using one we force the system call table into the text
section and it really belongs in the rodata section.
This also removes another use of dot symbols.
Signed-off-by: Anton Blanchard <anton@samba.org>
We have a number of places where we load the text address of a local
function and indirectly branch to it in assembly. Since it is an
indirect branch binutils will not know to use the function text
address, so that trick wont work.
There is no need for these functions to have a function descriptor
so we can replace it with a label and remove the dot symbol.
Signed-off-by: Anton Blanchard <anton@samba.org>
binutils is smart enough to know that a branch to a function
descriptor is actually a branch to the functions text address.
Alan tells me that binutils has been doing this for 9 years.
Signed-off-by: Anton Blanchard <anton@samba.org>
Powerpc allows reordering over its ll/sc implementation. Implement the
two new barriers as appropriate.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/n/tip-gg2ffgq32sjgy9b8lj6m3hsc@git.kernel.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-kernel@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
3bc955987f ("powerpc/PCI: Use list_for_each_entry() for bus traversal")
caused a NULL pointer dereference because the loop body set the iterator to
NULL:
Unable to handle kernel paging request for data at address 0x00000000
Faulting instruction address: 0xc000000000041d78
Oops: Kernel access of bad area, sig: 11 [#1]
...
NIP [c000000000041d78] .sys_pciconfig_iobase+0x68/0x1f0
LR [c000000000041e0c] .sys_pciconfig_iobase+0xfc/0x1f0
Call Trace:
[c0000003b4787db0] [c000000000041e0c] .sys_pciconfig_iobase+0xfc/0x1f0 (unreliable)
[c0000003b4787e30] [c000000000009ed8] syscall_exit+0x0/0x98
Fix it by using a temporary variable for the iterator.
[bhelgaas: changelog, drop tmp_bus initialization]
Fixes: 3bc955987f powerpc/PCI: Use list_for_each_entry() for bus traversal
Signed-off-by: Mike Qiu <qiudayu@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
3bc955987f ("powerpc/PCI: Use list_for_each_entry() for bus traversal")
caused a NULL pointer dereference because the loop body set the iterator to
NULL:
Unable to handle kernel paging request for data at address 0x00000000
Faulting instruction address: 0xc000000000041d78
Oops: Kernel access of bad area, sig: 11 [#1]
...
NIP [c000000000041d78] .sys_pciconfig_iobase+0x68/0x1f0
LR [c000000000041e0c] .sys_pciconfig_iobase+0xfc/0x1f0
Call Trace:
[c0000003b4787db0] [c000000000041e0c] .sys_pciconfig_iobase+0xfc/0x1f0 (unreliable)
[c0000003b4787e30] [c000000000009ed8] syscall_exit+0x0/0x98
Fix it by using a temporary variable for the iterator.
[bhelgaas: changelog, drop tmp_bus initialization]
Fixes: 3bc955987f powerpc/PCI: Use list_for_each_entry() for bus traversal
Signed-off-by: Mike Qiu <qiudayu@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit 8f619b5429 ("powerpc/ppc64: Do not turn AIL (reloc-on
interrupts) too early") added code to set the AIL bit in the LPCR
without checking whether the kernel is running in hypervisor mode. The
result is that when the kernel is running as a guest (i.e., under
PowerKVM or PowerVM), the processor takes a privileged instruction
interrupt at that point, causing a panic. The visible result is that
the kernel hangs after printing "returning from prom_init".
This fixes it by checking for hypervisor mode being available before
setting LPCR. If we are not in hypervisor mode, we enable relocation-on
interrupts later in pSeries_setup_arch using the H_SET_MODE hcall.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull more powerpc updates from Ben Herrenschmidt:
"Here are a few more powerpc things for you.
So you'll find here the conversion of the two new firmware sysfs
interfaces to the new API for self-removing files that Greg and Tejun
introduced, so they can finally remove the old one.
I'm also reverting the hwmon driver for powernv. I shouldn't have
merged it, I got a bit carried away here. I hadn't realized it was
never CCed to the relevant maintainer(s) and list(s), and happens to
have some issues so I'm taking it out and it will come back via the
proper channels.
The rest is a bunch of LE fixes (argh, some of the new stuff was
broken on LE, I really need to start testing LE myself !) and various
random fixes here and there.
Finally one bit that's not strictly a fix, which is the HVC OPAL
change to "kick" the HVC thread when the firmware tells us there is
new incoming data. I don't feel like waiting for this one, it's
simple enough, and it makes a big difference in console responsiveness
which is good for my nerves"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (26 commits)
powerpc/powernv Adapt opal-elog and opal-dump to new sysfs_remove_file_self
Revert "powerpc/powernv: hwmon driver for power values, fan rpm and temperature"
power, sched: stop updating inside arch_update_cpu_topology() when nothing to be update
powerpc/le: Avoid creatng R_PPC64_TOCSAVE relocations for modules.
arch/powerpc: Use RCU_INIT_POINTER(x, NULL) in platforms/cell/spu_syscalls.c
powerpc/opal: Add missing include
powerpc: Convert last uses of __FUNCTION__ to __func__
powerpc: Add lq/stq emulation
powerpc/powernv: Add invalid OPAL call
powerpc/powernv: Add OPAL message log interface
powerpc/book3s: Fix mc_recoverable_range buffer overrun issue.
powerpc: Remove dead code in sycall entry
powerpc: Use of_node_init() for the fakenode in msi_bitmap.c
powerpc/mm: NUMA pte should be handled via slow path in get_user_pages_fast()
powerpc/powernv: Fix endian issues with sensor code
powerpc/powernv: Fix endian issues with OPAL async code
tty/hvc_opal: Kick the HVC thread on OPAL console events
powerpc/powernv: Add opal_notifier_unregister() and export to modules
powerpc/ppc64: Do not turn AIL (reloc-on interrupts) too early
powerpc/ppc64: Gracefully handle early interrupts
...
Recent CPUs support quad word load and store instructions. Add
support to the alignment handler for them.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In:
commit 742415d6b6
Author: Michael Neuling <mikey@neuling.org>
powerpc: Turn syscall handler into macros
We converted the syscall entry code onto macros, but in doing this we
introduced some cruft that's never run and should never have been added.
This removes that code.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The purpose of this single series of commits from Srivatsa S Bhat (with
a small piece from Gautham R Shenoy) touching multiple subsystems that use
CPU hotplug notifiers is to provide a way to register them that will not
lead to deadlocks with CPU online/offline operations as described in the
changelog of commit 93ae4f978c (CPU hotplug: Provide lockless versions
of callback registration functions).
The first three commits in the series introduce the API and document it
and the rest simply goes through the users of CPU hotplug notifiers and
converts them to using the new method.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=SW7Q
-----END PGP SIGNATURE-----
Merge tag 'cpu-hotplug-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull CPU hotplug notifiers registration fixes from Rafael Wysocki:
"The purpose of this single series of commits from Srivatsa S Bhat
(with a small piece from Gautham R Shenoy) touching multiple
subsystems that use CPU hotplug notifiers is to provide a way to
register them that will not lead to deadlocks with CPU online/offline
operations as described in the changelog of commit 93ae4f978c ("CPU
hotplug: Provide lockless versions of callback registration
functions").
The first three commits in the series introduce the API and document
it and the rest simply goes through the users of CPU hotplug notifiers
and converts them to using the new method"
* tag 'cpu-hotplug-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (52 commits)
net/iucv/iucv.c: Fix CPU hotplug callback registration
net/core/flow.c: Fix CPU hotplug callback registration
mm, zswap: Fix CPU hotplug callback registration
mm, vmstat: Fix CPU hotplug callback registration
profile: Fix CPU hotplug callback registration
trace, ring-buffer: Fix CPU hotplug callback registration
xen, balloon: Fix CPU hotplug callback registration
hwmon, via-cputemp: Fix CPU hotplug callback registration
hwmon, coretemp: Fix CPU hotplug callback registration
thermal, x86-pkg-temp: Fix CPU hotplug callback registration
octeon, watchdog: Fix CPU hotplug callback registration
oprofile, nmi-timer: Fix CPU hotplug callback registration
intel-idle: Fix CPU hotplug callback registration
clocksource, dummy-timer: Fix CPU hotplug callback registration
drivers/base/topology.c: Fix CPU hotplug callback registration
acpi-cpufreq: Fix CPU hotplug callback registration
zsmalloc: Fix CPU hotplug callback registration
scsi, fcoe: Fix CPU hotplug callback registration
scsi, bnx2fc: Fix CPU hotplug callback registration
scsi, bnx2i: Fix CPU hotplug callback registration
...
Turn them on at the same time as we allow MSR_IR/DR in the paca
kernel MSR, ie, after the MMU has been setup enough to be able
to handle relocated access to the linear mapping.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we take an interrupt such as a trap caused by a BUG_ON before the
MMU has been setup, the interrupt handlers try to enable virutal mode
and cause a recursive crash, making the original problem very hard
to debug.
This fixes it by adjusting the "kernel_msr" value in the PACA so that
it only has MSR_IR and MSR_DR (translation for instruction and data)
set after the MMU has been initialized for the processor.
We may still not have a console yet but at least we don't get into
a recursive fault (and early debug console or memory dump via JTAG
of the kernel buffer *will* give us the proper error).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
All our cpu feature updates were done for every CPU in the device-tree,
thus overwriting the cputable bits over and over again. Instead do them
only for the boot CPU.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Move the definition to setup-common.c and set the init value
to -1 on both 32 and 64-bit (it was 0 on 64-bit).
Additionally add a check to prom.c to garantee that the init
value has been udpated after the DT scan.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For historical reasons that code was under #ifdef CONFIG_PPC_PSERIES
but it applies equally to all 64-bit platforms.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We can't take an IRQ when we're about to do a trechkpt as our GPR state is set
to user GPR values.
We've hit this when running some IBM Java stress tests in the lab resulting in
the following dump:
cpu 0x3f: Vector: 700 (Program Check) at [c000000007eb3d40]
pc: c000000000050074: restore_gprs+0xc0/0x148
lr: 00000000b52a8184
sp: ac57d360
msr: 8000000100201030
current = 0xc00000002c500000
paca = 0xc000000007dbfc00 softe: 0 irq_happened: 0x00
pid = 34535, comm = Pooled Thread #
R00 = 00000000b52a8184 R16 = 00000000b3e48fda
R01 = 00000000ac57d360 R17 = 00000000ade79bd8
R02 = 00000000ac586930 R18 = 000000000fac9bcc
R03 = 00000000ade60000 R19 = 00000000ac57f930
R04 = 00000000f6624918 R20 = 00000000ade79be8
R05 = 00000000f663f238 R21 = 00000000ac218a54
R06 = 0000000000000002 R22 = 000000000f956280
R07 = 0000000000000008 R23 = 000000000000007e
R08 = 000000000000000a R24 = 000000000000000c
R09 = 00000000b6e69160 R25 = 00000000b424cf00
R10 = 0000000000000181 R26 = 00000000f66256d4
R11 = 000000000f365ec0 R27 = 00000000b6fdcdd0
R12 = 00000000f66400f0 R28 = 0000000000000001
R13 = 00000000ada71900 R29 = 00000000ade5a300
R14 = 00000000ac2185a8 R30 = 00000000f663f238
R15 = 0000000000000004 R31 = 00000000f6624918
pc = c000000000050074 restore_gprs+0xc0/0x148
cfar= c00000000004fe28 dont_restore_vec+0x1c/0x1a4
lr = 00000000b52a8184
msr = 8000000100201030 cr = 24804888
ctr = 0000000000000000 xer = 0000000000000000 trap = 700
This moves tm_recheckpoint to a C function and moves the tm_restore_sprs into
that function. It then adds IRQ disabling over the trechkpt critical section.
It also sets the TEXASR FS in the signals code to ensure this is never set now
that we explictly write the TM sprs in tm_recheckpoint.
Signed-off-by: Michael Neuling <mikey@neuling.org>
cc: stable@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The current kernel code assumes big endian and parses RTAS events all
wrong. The most visible effect is that we cannot honor EPOW events,
meaning, for example, we cannot shut down a guest properly from the
hypervisor.
This new patch is largely inspired by Nathan's work: we get rid of all
the bit fields in the RTAS event structures (even the unused ones, for
consistency). We also introduce endian safe accessors for the fields used
by the kernel (trivial rtas_error_type() accessor added for consistency).
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
But there were a few features that were added.
Uprobes now work with event triggers and multi buffers.
Uprobes have support under ftrace and perf.
The big feature is that the function tracer can now be used within the
multi buffer instances. That is, you can now trace some functions
in one buffer, others in another buffer, all functions in a third buffer
and so on. They are basically agnostic from each other. This only
works for the function tracer and not for the function graph trace,
although you can have the function graph tracer running in the top level
buffer (or any tracer for that matter) and have different function tracing
going on in the sub buffers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTOthtAAoJEKQekfcNnQGu5c8H/Ana/U+0tmksp1dbHkRHsKSH
+Fsv4Jeu8gf1NaFKHEhkUTcFtnzE6qAPV2VCrcJwXbhAhhwZm+LjrnWdoy3215S3
cQW4LftLEonh2cM36Cos74TulMEYN6XmL6dQZV+CILKQkDrWU4qJjQ64okXEkqrd
9iG3p/mSXyvJcmnyg61ALnMOhZDLsXY3djBhWBPhiTPGS6BRb9zh4Pmw6Zv0n2rJ
U93Gt/3AQrv1ybu73dUxqP0abp60oXOiWoF/R2jcbKqIM+K9RPJX79unCV3jq3u9
f+6jMlB9PgAMqQj6ihJdwxKDDuzwyrVdEPnsgvl4jarCBCtVVwhKedBaKN/KS8k=
=HdXY
-----END PGP SIGNATURE-----
Merge tag 'trace-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"Most of the changes were largely clean ups, and some documentation.
But there were a few features that were added:
Uprobes now work with event triggers and multi buffers and have
support under ftrace and perf.
The big feature is that the function tracer can now be used within the
multi buffer instances. That is, you can now trace some functions in
one buffer, others in another buffer, all functions in a third buffer
and so on. They are basically agnostic from each other. This only
works for the function tracer and not for the function graph trace,
although you can have the function graph tracer running in the top
level buffer (or any tracer for that matter) and have different
function tracing going on in the sub buffers"
* tag 'trace-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (45 commits)
tracing: Add BUG_ON when stack end location is over written
tracepoint: Remove unused API functions
Revert "tracing: Move event storage for array from macro to standalone function"
ftrace: Constify ftrace_text_reserved
tracepoints: API doc update to tracepoint_probe_register() return value
tracepoints: API doc update to data argument
ftrace: Fix compilation warning about control_ops_free
ftrace/x86: BUG when ftrace recovery fails
ftrace: Warn on error when modifying ftrace function
ftrace: Remove freelist from struct dyn_ftrace
ftrace: Do not pass data to ftrace_dyn_arch_init
ftrace: Pass retval through return in ftrace_dyn_arch_init()
ftrace: Inline the code from ftrace_dyn_table_alloc()
ftrace: Cleanup of global variables ftrace_new_pgs and ftrace_update_cnt
tracing: Evaluate len expression only once in __dynamic_array macro
tracing: Correctly expand len expressions from __dynamic_array macro
tracing/module: Replace include of tracepoint.h with jump_label.h in module.h
tracing: Fix event header migrate.h to include tracepoint.h
tracing: Fix event header writeback.h to include tracepoint.h
tracing: Warn if a tracepoint is not set via debugfs
...
Updates to devicetree core code. This branch contains the following notable changes:
* Add reserved memory binding
* Make struct device_node a kobject and remove legacy /proc/device-tree
* ePAPR conformance fixes
* Update in-kernel DTC copy to version v1.4.0
* Preparation changes for dynamic device tree overlays
* minor bug fixes and documentation changes
The most significant change in this branch is the conversion of struct
device_node to be a kobject that is exposed via sysfs and removal of the
old /proc/device-tree code. This simplifies the device tree handling
code and tightens up the lifecycle on device tree nodes.
[updated: added fix for dangling select PROC_DEVICETREE]
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=lyA5
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.secretlab.ca/git/linux
Pull devicetree changes from Grant Likely:
"Updates to devicetree core code. This branch contains the following
notable changes:
- add reserved memory binding
- make struct device_node a kobject and remove legacy
/proc/device-tree
- ePAPR conformance fixes
- update in-kernel DTC copy to version v1.4.0
- preparatory changes for dynamic device tree overlays
- minor bug fixes and documentation changes
The most significant change in this branch is the conversion of struct
device_node to be a kobject that is exposed via sysfs and removal of
the old /proc/device-tree code. This simplifies the device tree
handling code and tightens up the lifecycle on device tree nodes.
[updated: added fix for dangling select PROC_DEVICETREE]"
* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux: (29 commits)
dt: Remove dangling "select PROC_DEVICETREE"
of: Add support for ePAPR "stdout-path" property
of: device_node kobject lifecycle fixes
of: only scan for reserved mem when fdt present
powerpc: add support for reserved memory defined by device tree
arm64: add support for reserved memory defined by device tree
of: add missing major vendors
of: add vendor prefix for SMSC
of: remove /proc/device-tree
of/selftest: Add self tests for manipulation of properties
of: Make device nodes kobjects so they show up in sysfs
arm: add support for reserved memory defined by device tree
drivers: of: add support for custom reserved memory drivers
drivers: of: add initialization code for dynamic reserved memory
drivers: of: add initialization code for static reserved memory
of: document bindings for reserved-memory nodes
Revert "of: fix of_update_property()"
kbuild: dtbs_install: new make target
ARM: mvebu: Allows to get the SoC ID even without PCI enabled
of: Allows to use the PCI translator without the PCI core
...
Pull powerpc non-virtualized cpuidle from Ben Herrenschmidt:
"This is the branch I mentioned in my other pull request which contains
our improved cpuidle support for the "powernv" platform
(non-virtualized).
It adds support for the "fast sleep" feature of the processor which
provides higher power savings than our usual "nap" mode but at the
cost of losing the timers while asleep, and thus exploits the new
timer broadcast framework to work around that limitation.
It's based on a tip timer tree that you seem to have already merged"
* 'powernv-cpuidle' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
cpuidle/powernv: Parse device tree to setup idle states
cpuidle/powernv: Add "Fast-Sleep" CPU idle state
powerpc/powernv: Add OPAL call to resync timebase on wakeup
powerpc/powernv: Add context management for Fast Sleep
powerpc: Split timer_interrupt() into timer handling and interrupt handling routines
powerpc: Implement tick broadcast IPI as a fixed IPI message
powerpc: Free up the slot of PPC_MSG_CALL_FUNC_SINGLE IPI message
Pull main powerpc updates from Ben Herrenschmidt:
"This time around, the powerpc merges are going to be a little bit more
complicated than usual.
This is the main pull request with most of the work for this merge
window. I will describe it a bit more further down.
There is some additional cpuidle driver work, however I haven't
included it in this tree as it depends on some work in tip/timer-core
which Thomas accidentally forgot to put in a topic branch. Since I
didn't want to carry all of that tip timer stuff in powerpc -next, I
setup a separate branch on top of Thomas tree with just that cpuidle
driver in it, and Stephen has been carrying that in next separately
for a while now. I'll send a separate pull request for it.
Additionally, two new pieces in this tree add users for a sysfs API
that Tejun and Greg have been deprecating in drivers-core-next.
Thankfully Greg reverted the patch that removes the old API so this
merge can happen cleanly, but once merged, I will send a patch
adjusting our new code to the new API so that Greg can send you the
removal patch.
Now as for the content of this branch, we have a lot of perf work for
power8 new counters including support for our new "nest" counters
(also called 24x7) under pHyp (not natively yet).
We have new functionality when running under the OPAL firmware
(non-virtualized or KVM host), such as access to the firmware error
logs and service processor dumps, system parameters and sensors, along
with a hwmon driver for the latter.
There's also a bunch of bug fixes accross the board, some LE fixes,
and a nice set of selftests for validating our various types of copy
loops.
On the Freescale side, we see mostly new chip/board revisions, some
clock updates, better support for machine checks and debug exceptions,
etc..."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (70 commits)
powerpc/book3s: Fix CFAR clobbering issue in machine check handler.
powerpc/compat: 32-bit little endian machine name is ppcle, not ppc
powerpc/le: Big endian arguments for ppc_rtas()
powerpc: Use default set of netfilter modules (CONFIG_NETFILTER_ADVANCED=n)
powerpc/defconfigs: Enable THP in pseries defconfig
powerpc/mm: Make sure a local_irq_disable prevent a parallel THP split
powerpc: Rate-limit users spamming kernel log buffer
powerpc/perf: Fix handling of L3 events with bank == 1
powerpc/perf/hv_{gpci, 24x7}: Add documentation of device attributes
powerpc/perf: Add kconfig option for hypervisor provided counters
powerpc/perf: Add support for the hv 24x7 interface
powerpc/perf: Add support for the hv gpci (get performance counter info) interface
powerpc/perf: Add macros for defining event fields & formats
powerpc/perf: Add a shared interface to get gpci version and capabilities
powerpc/perf: Add 24x7 interface headers
powerpc/perf: Add hv_gpci interface header
powerpc: Add hvcalls for 24x7 and gpci (Get Performance Counter Info)
sysfs: create bin_attributes under the requested group
powerpc/perf: Enable BHRB access for EBB events
powerpc/perf: Add BHRB constraint and IFM MMCRA handling for EBB
...
Enumeration
- Increment max correctly in pci_scan_bridge() (Andreas Noever)
- Clarify the "scan anyway" comment in pci_scan_bridge() (Andreas Noever)
- Assign CardBus bus number only during the second pass (Andreas Noever)
- Use request_resource_conflict() instead of insert_ for bus numbers (Andreas Noever)
- Make sure bus number resources stay within their parents bounds (Andreas Noever)
- Remove pci_fixup_parent_subordinate_busnr() (Andreas Noever)
- Check for child busses which use more bus numbers than allocated (Andreas Noever)
- Don't scan random busses in pci_scan_bridge() (Andreas Noever)
- x86: Drop pcibios_scan_root() check for bus already scanned (Bjorn Helgaas)
- x86: Use pcibios_scan_root() instead of pci_scan_bus_with_sysdata() (Bjorn Helgaas)
- x86: Use pcibios_scan_root() instead of pci_scan_bus_on_node() (Bjorn Helgaas)
- x86: Merge pci_scan_bus_on_node() into pcibios_scan_root() (Bjorn Helgaas)
- x86: Drop return value of pcibios_scan_root() (Bjorn Helgaas)
NUMA
- x86: Add x86_pci_root_bus_node() to look up NUMA node from PCI bus (Bjorn Helgaas)
- x86: Use x86_pci_root_bus_node() instead of get_mp_bus_to_node() (Bjorn Helgaas)
- x86: Remove mp_bus_to_node[], set_mp_bus_to_node(), get_mp_bus_to_node() (Bjorn Helgaas)
- x86: Use NUMA_NO_NODE, not -1, for unknown node (Bjorn Helgaas)
- x86: Remove acpi_get_pxm() usage (Bjorn Helgaas)
- ia64: Use NUMA_NO_NODE, not MAX_NUMNODES, for unknown node (Bjorn Helgaas)
- ia64: Remove acpi_get_pxm() usage (Bjorn Helgaas)
- ACPI: Fix acpi_get_node() prototype (Bjorn Helgaas)
Resource management
- i2o: Fix and refactor PCI space allocation (Bjorn Helgaas)
- Add resource_contains() (Bjorn Helgaas)
- Add %pR support for IORESOURCE_UNSET (Bjorn Helgaas)
- Mark resources as IORESOURCE_UNSET if we can't assign them (Bjorn Helgaas)
- Don't clear IORESOURCE_UNSET when updating BAR (Bjorn Helgaas)
- Check IORESOURCE_UNSET before updating BAR (Bjorn Helgaas)
- Don't try to claim IORESOURCE_UNSET resources (Bjorn Helgaas)
- Mark 64-bit resource as IORESOURCE_UNSET if we only support 32-bit (Bjorn Helgaas)
- Don't enable decoding if BAR hasn't been assigned an address (Bjorn Helgaas)
- Add "weak" generic pcibios_enable_device() implementation (Bjorn Helgaas)
- alpha, microblaze, sh, sparc, tile: Use default pcibios_enable_device() (Bjorn Helgaas)
- s390: Use generic pci_enable_resources() (Bjorn Helgaas)
- Don't check resource_size() in pci_bus_alloc_resource() (Bjorn Helgaas)
- Set type in __request_region() (Bjorn Helgaas)
- Check all IORESOURCE_TYPE_BITS in pci_bus_alloc_from_region() (Bjorn Helgaas)
- Change pci_bus_alloc_resource() type_mask to unsigned long (Bjorn Helgaas)
- Log IDE resource quirk in dmesg (Bjorn Helgaas)
- Revert "[PATCH] Insert GART region into resource map" (Bjorn Helgaas)
PCI device hotplug
- Make check_link_active() non-static (Rajat Jain)
- Use link change notifications for hot-plug and removal (Rajat Jain)
- Enable link state change notifications (Rajat Jain)
- Don't disable the link permanently during removal (Rajat Jain)
- Don't check adapter or latch status while disabling (Rajat Jain)
- Disable link notification across slot reset (Rajat Jain)
- Ensure very fast hotplug events are also processed (Rajat Jain)
- Add hotplug_lock to serialize hotplug events (Rajat Jain)
- Remove a non-existent card, regardless of "surprise" capability (Rajat Jain)
- Don't turn slot off when hot-added device already exists (Yijing Wang)
MSI
- Keep pci_enable_msi() documentation (Alexander Gordeev)
- ahci: Fix broken single MSI fallback (Alexander Gordeev)
- ahci, vfio: Use pci_enable_msi_range() (Alexander Gordeev)
- Check kmalloc() return value, fix leak of name (Greg Kroah-Hartman)
- Fix leak of msi_attrs (Greg Kroah-Hartman)
- Fix pci_msix_vec_count() htmldocs failure (Masanari Iida)
Virtualization
- Device-specific ACS support (Alex Williamson)
Freescale i.MX6
- Wait for retraining (Marek Vasut)
Marvell MVEBU
- Use Device ID and revision from underlying endpoint (Andrew Lunn)
- Fix incorrect size for PCI aperture resources (Jason Gunthorpe)
- Call request_resource() on the apertures (Jason Gunthorpe)
- Fix potential issue in range parsing (Jean-Jacques Hiblot)
Renesas R-Car
- Check platform_get_irq() return code (Ben Dooks)
- Add error interrupt handling (Ben Dooks)
- Fix bridge logic configuration accesses (Ben Dooks)
- Register each instance independently (Magnus Damm)
- Break out window size handling (Magnus Damm)
- Make the Kconfig dependencies more generic (Magnus Damm)
Synopsys DesignWare
- Fix RC BAR to be single 64-bit non-prefetchable memory (Mohit Kumar)
Miscellaneous
- Remove unused SR-IOV VF Migration support (Bjorn Helgaas)
- Enable INTx if BIOS left them disabled (Bjorn Helgaas)
- Fix hex vs decimal typo in cpqhpc_probe() (Dan Carpenter)
- Clean up par-arch object file list (Liviu Dudau)
- Set IORESOURCE_ROM_SHADOW only for the default VGA device (Sander Eikelenboom)
- ACPI, ARM, drm, powerpc, pcmcia, PCI: Use list_for_each_entry() for bus traversal (Yijing Wang)
- Fix pci_bus_b() build failure (Paul Gortmaker)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=3mNS
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.15-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Enumeration
- Increment max correctly in pci_scan_bridge() (Andreas Noever)
- Clarify the "scan anyway" comment in pci_scan_bridge() (Andreas Noever)
- Assign CardBus bus number only during the second pass (Andreas Noever)
- Use request_resource_conflict() instead of insert_ for bus numbers (Andreas Noever)
- Make sure bus number resources stay within their parents bounds (Andreas Noever)
- Remove pci_fixup_parent_subordinate_busnr() (Andreas Noever)
- Check for child busses which use more bus numbers than allocated (Andreas Noever)
- Don't scan random busses in pci_scan_bridge() (Andreas Noever)
- x86: Drop pcibios_scan_root() check for bus already scanned (Bjorn Helgaas)
- x86: Use pcibios_scan_root() instead of pci_scan_bus_with_sysdata() (Bjorn Helgaas)
- x86: Use pcibios_scan_root() instead of pci_scan_bus_on_node() (Bjorn Helgaas)
- x86: Merge pci_scan_bus_on_node() into pcibios_scan_root() (Bjorn Helgaas)
- x86: Drop return value of pcibios_scan_root() (Bjorn Helgaas)
NUMA
- x86: Add x86_pci_root_bus_node() to look up NUMA node from PCI bus (Bjorn Helgaas)
- x86: Use x86_pci_root_bus_node() instead of get_mp_bus_to_node() (Bjorn Helgaas)
- x86: Remove mp_bus_to_node[], set_mp_bus_to_node(), get_mp_bus_to_node() (Bjorn Helgaas)
- x86: Use NUMA_NO_NODE, not -1, for unknown node (Bjorn Helgaas)
- x86: Remove acpi_get_pxm() usage (Bjorn Helgaas)
- ia64: Use NUMA_NO_NODE, not MAX_NUMNODES, for unknown node (Bjorn Helgaas)
- ia64: Remove acpi_get_pxm() usage (Bjorn Helgaas)
- ACPI: Fix acpi_get_node() prototype (Bjorn Helgaas)
Resource management
- i2o: Fix and refactor PCI space allocation (Bjorn Helgaas)
- Add resource_contains() (Bjorn Helgaas)
- Add %pR support for IORESOURCE_UNSET (Bjorn Helgaas)
- Mark resources as IORESOURCE_UNSET if we can't assign them (Bjorn Helgaas)
- Don't clear IORESOURCE_UNSET when updating BAR (Bjorn Helgaas)
- Check IORESOURCE_UNSET before updating BAR (Bjorn Helgaas)
- Don't try to claim IORESOURCE_UNSET resources (Bjorn Helgaas)
- Mark 64-bit resource as IORESOURCE_UNSET if we only support 32-bit (Bjorn Helgaas)
- Don't enable decoding if BAR hasn't been assigned an address (Bjorn Helgaas)
- Add "weak" generic pcibios_enable_device() implementation (Bjorn Helgaas)
- alpha, microblaze, sh, sparc, tile: Use default pcibios_enable_device() (Bjorn Helgaas)
- s390: Use generic pci_enable_resources() (Bjorn Helgaas)
- Don't check resource_size() in pci_bus_alloc_resource() (Bjorn Helgaas)
- Set type in __request_region() (Bjorn Helgaas)
- Check all IORESOURCE_TYPE_BITS in pci_bus_alloc_from_region() (Bjorn Helgaas)
- Change pci_bus_alloc_resource() type_mask to unsigned long (Bjorn Helgaas)
- Log IDE resource quirk in dmesg (Bjorn Helgaas)
- Revert "[PATCH] Insert GART region into resource map" (Bjorn Helgaas)
PCI device hotplug
- Make check_link_active() non-static (Rajat Jain)
- Use link change notifications for hot-plug and removal (Rajat Jain)
- Enable link state change notifications (Rajat Jain)
- Don't disable the link permanently during removal (Rajat Jain)
- Don't check adapter or latch status while disabling (Rajat Jain)
- Disable link notification across slot reset (Rajat Jain)
- Ensure very fast hotplug events are also processed (Rajat Jain)
- Add hotplug_lock to serialize hotplug events (Rajat Jain)
- Remove a non-existent card, regardless of "surprise" capability (Rajat Jain)
- Don't turn slot off when hot-added device already exists (Yijing Wang)
MSI
- Keep pci_enable_msi() documentation (Alexander Gordeev)
- ahci: Fix broken single MSI fallback (Alexander Gordeev)
- ahci, vfio: Use pci_enable_msi_range() (Alexander Gordeev)
- Check kmalloc() return value, fix leak of name (Greg Kroah-Hartman)
- Fix leak of msi_attrs (Greg Kroah-Hartman)
- Fix pci_msix_vec_count() htmldocs failure (Masanari Iida)
Virtualization
- Device-specific ACS support (Alex Williamson)
Freescale i.MX6
- Wait for retraining (Marek Vasut)
Marvell MVEBU
- Use Device ID and revision from underlying endpoint (Andrew Lunn)
- Fix incorrect size for PCI aperture resources (Jason Gunthorpe)
- Call request_resource() on the apertures (Jason Gunthorpe)
- Fix potential issue in range parsing (Jean-Jacques Hiblot)
Renesas R-Car
- Check platform_get_irq() return code (Ben Dooks)
- Add error interrupt handling (Ben Dooks)
- Fix bridge logic configuration accesses (Ben Dooks)
- Register each instance independently (Magnus Damm)
- Break out window size handling (Magnus Damm)
- Make the Kconfig dependencies more generic (Magnus Damm)
Synopsys DesignWare
- Fix RC BAR to be single 64-bit non-prefetchable memory (Mohit Kumar)
Miscellaneous
- Remove unused SR-IOV VF Migration support (Bjorn Helgaas)
- Enable INTx if BIOS left them disabled (Bjorn Helgaas)
- Fix hex vs decimal typo in cpqhpc_probe() (Dan Carpenter)
- Clean up par-arch object file list (Liviu Dudau)
- Set IORESOURCE_ROM_SHADOW only for the default VGA device (Sander Eikelenboom)
- ACPI, ARM, drm, powerpc, pcmcia, PCI: Use list_for_each_entry() for bus traversal (Yijing Wang)
- Fix pci_bus_b() build failure (Paul Gortmaker)"
* tag 'pci-v3.15-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (108 commits)
Revert "[PATCH] Insert GART region into resource map"
PCI: Log IDE resource quirk in dmesg
PCI: Change pci_bus_alloc_resource() type_mask to unsigned long
PCI: Check all IORESOURCE_TYPE_BITS in pci_bus_alloc_from_region()
resources: Set type in __request_region()
PCI: Don't check resource_size() in pci_bus_alloc_resource()
s390/PCI: Use generic pci_enable_resources()
tile PCI RC: Use default pcibios_enable_device()
sparc/PCI: Use default pcibios_enable_device() (Leon only)
sh/PCI: Use default pcibios_enable_device()
microblaze/PCI: Use default pcibios_enable_device()
alpha/PCI: Use default pcibios_enable_device()
PCI: Add "weak" generic pcibios_enable_device() implementation
PCI: Don't enable decoding if BAR hasn't been assigned an address
PCI: Enable INTx in pci_reenable_device() only when MSI/MSI-X not enabled
PCI: Mark 64-bit resource as IORESOURCE_UNSET if we only support 32-bit
PCI: Don't try to claim IORESOURCE_UNSET resources
PCI: Check IORESOURCE_UNSET before updating BAR
PCI: Don't clear IORESOURCE_UNSET when updating BAR
PCI: Mark resources as IORESOURCE_UNSET if we can't assign them
...
Conflicts:
arch/x86/include/asm/topology.h
drivers/ata/ahci.c
Freescale updates from Scott. Mostly support for critical
and machine check exceptions on 64-bit BookE, some new
PCI suspend/resume work and misc bits.
While checking powersaving mode in machine check handler at 0x200, we
clobber CFAR register. Fix it by saving and restoring it during beq/bgt.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The ppc_rtas() syscall allows userspace to interact directly with RTAS.
For the moment, it assumes every thing is big endian and returns either
EINVAL or EFAULT when called in a little endian environment.
As suggested by Benjamin, to avoid bugs when userspace wants to pass
a non 32 bit value to RTAS, it is far better to stick with a simple
rationale: ppc_rtas() should be called with a big endian rtas_args
structure.
With this patch, it is now up to userspace to forge big endian arguments,
as expected by RTAS.
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The facility unavailable exception can be triggered from userspace by
accessing PMU registers when EBB is not enabled. This causes the
included pr_err() to run, hence spamming the kernel log buffer.
This avoids this by rate limiting these messages.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some power8 revisions have a hardware bug where we can lose a
Performance Monitor (PMU) exception under certain circumstances.
We will be adding a workaround for this case, see the next commit for
details. The observed behaviour is that writing PMAO doesn't cause an
exception as we would expect, hence the name of the feature.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Subsystems that want to register CPU hotplug callbacks, as well as perform
initialization for the CPUs that are already online, often do it as shown
below:
get_online_cpus();
for_each_online_cpu(cpu)
init_cpu(cpu);
register_cpu_notifier(&foobar_cpu_notifier);
put_online_cpus();
This is wrong, since it is prone to ABBA deadlocks involving the
cpu_add_remove_lock and the cpu_hotplug.lock (when running concurrently
with CPU hotplug operations).
Instead, the correct and race-free way of performing the callback
registration is:
cpu_notifier_register_begin();
for_each_online_cpu(cpu)
init_cpu(cpu);
/* Note the use of the double underscored version of the API */
__register_cpu_notifier(&foobar_cpu_notifier);
cpu_notifier_register_done();
Fix the sysfs code in powerpc by using this latter form of callback
registration.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Olof Johansson <olof@lixom.net>
Cc: Wang Dongsheng <dongsheng.wang@freescale.com>
Cc: Ingo Molnar <mingo@kernel.org>
Acked-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add special state saving for critical and machine check exceptions.
Most of this code could be used to handle debug exceptions taken from
kernel space, but actually doing so is outside the scope of this patch.
The various critical and machine check exceptions now point to their
real handlers, rather than hanging the kernel.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Use the proper scratch SPRG and PACA region. Introduce level-specific
macros to simplify usage and avoid needing to do a bunch of token
pasting throughout EXCEPTION_COMMON().
Now that EXCEPTION_COMMON_DBG() is properly using the debug scratch
register, there's no more need for the caller to move the value to the
GEN scratch first.
Signed-off-by: Scott Wood <scottwood@freescale.com>
The ints parameter was used to optionally insert RECONCILE_IRQ_STATE
into EXCEPTION_COMMON. However, since it came at the end of
EXCEPTION_COMMON, there was no real benefit for it to be there as
opposed to being called separately by the caller of EXCEPTION_COMMON.
The ints parameter was causing some hassle when trying to add an extra
macro layer. Besides avoiding that, moving "ints" to the caller makes
the code simpler by:
- avoiding the asymmetry where INTS_RESTORE_HARD is called separately
by the individual exception, but INTS_DISABLE was not
- removing the no-op INTS_KEEP
- not having an unnecessary macro parameter
It also turned out to be necessary to delay the INTS_DISABLE
in the case of special level exceptions until after we saved the
old value of PACAIRQHAPPENED.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Previously SPRG3 was marked for use by both VDSO and critical
interrupts (though critical interrupts were not fully implemented).
In commit 8b64a9dfb0 ("powerpc/booke64:
Use SPRG0/3 scratch for bolted TLB miss & crit int"), Mihai Caraman
made an attempt to resolve this conflict by restoring the VDSO value
early in the critical interrupt, but this has some issues:
- It's incompatible with EXCEPTION_COMMON which restores r13 from the
by-then-overwritten scratch (this cost me some debugging time).
- It forces critical exceptions to be a special case handled
differently from even machine check and debug level exceptions.
- It didn't occur to me that it was possible to make this work at all
(by doing a final "ld r13, PACA_EXCRIT+EX_R13(r13)") until after
I made (most of) this patch. :-)
It might be worth investigating using a load rather than SPRG on return
from all exceptions (except TLB misses where the scratch never leaves
the SPRG) -- it could save a few cycles. Until then, let's stick with
SPRG for all exceptions.
Since we cannot use SPRG4-7 for scratch without corrupting the state of
a KVM guest, move VDSO to SPRG7 on book3e. Since neither SPRG4-7 nor
critical interrupts exist on book3s, SPRG3 is still used for VDSO
there.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Mihai Caraman <mihai.caraman@freescale.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: kvm-ppc@vger.kernel.org
Once special level interrupts are supported, we may take nested TLB
misses -- so allow the same thread to acquire the lock recursively.
The lock will not be effective against the nested TLB miss handler
trying to write the same entry as the interrupted TLB miss handler, but
that's also a problem on non-threaded CPUs that lack TLB write
conditional. This will be addressed in the patch that enables crit/mc
support by invalidating the TLB on return from level exceptions.
Signed-off-by: Scott Wood <scottwood@freescale.com>
altivec_unavailable was commented as 0xf20 but the code uses 0x200.
Note that 0xf20 is also used by ap_unavailable.
altivec_assist was commented as 0x1700 but the code uses 0x220.
critical_input was commented as 0x580 but the code uses 0x100.
machine_check was commented and implemented as 0x200, which conflicts
with altivec_assist (it only builds because MC_EXCEPTION_PROLOG is
commented out). Changed to the fixed IVOR value of 0x000.
Signed-off-by: Scott Wood <scottwood@freescale.com>
We need to store thread info to these exception thread info like something
we already did for PPC32.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
We already allocated critical/machine/debug check exceptions, but
we also should initialize those associated kernel stack pointers
for use by special exceptions in the PACA.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Enable reserved memory initialization from device tree.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
