The Welland ME-747K-SI AoE target generates unsolicited AoE responses that
are marked as vendor extensions. Instead of ignoring these packets, the
aoe driver was generating kernel messages for each unrecognized response
received. This patch corrects the behavior.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Reported-by: <karaluh@karaluh.pl>
Tested-by: <karaluh@karaluh.pl>
Cc: <stable@kernel.org>
Cc: Alex Buell <alex.buell@munted.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If a USB PCI controller is behind a cardbus bridge, we are trying to
restore its configuration registers too early, before the cardbus
bridge is operational. To fix this, call pci_restore_state() from
usb_hcd_pci_resume() and remove usb_hcd_pci_resume_early() which is
no longer necessary (the configuration spaces of USB controllers that
are not behind cardbus bridges will be restored by the PCI PM core
with interrupts disabled anyway).
This patch fixes the regression from 2.6.28 tracked as
http://bugzilla.kernel.org/show_bug.cgi?id=12659
[ Side note: the proper long-term fix is probably to just force the
unplug event at suspend time instead of doing a plug/unplug at resume
time, but this patch is fine regardless - Linus ]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
sata_nv: give up hardreset on nf2
libata-sff: fix 32-bit PIO ATAPI regression
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: fix bus endianity in file2alias
HID: move tmff and zpff devices from ignore_list to blacklist
HID: unlock properly on error paths in hidraw_ioctl()
HID: blacklist Powercom USB UPS
* 'for-linus' of git://git.o-hand.com/linux-mfd:
mfd: Fix sm501_register_gpio section mismatch
mfd: fix sm501 section mismatches
mfd: terminate pcf50633 i2c_device_id list
mfd: Ensure all WM8350 IRQs are masked at startup
mfd: fix htc-egpio iomem resource handling using resource_size
mfd: Fix TWL4030 build on some ARM variants
mfd: wm8350 tries reaches -1
mfd: Mark WM835x USB_SLV_500MA bit as accessible
mfd: Improve diagnostics for WM8350 ID register probe
mfd: Initialise WM8350 interrupts earlier
mfd: Fix egpio kzalloc return test
This is the cause of the DMA faults and disk corruption that people have
been seeing. Some chipsets neglect to report the RWBF "capability" --
the flag which says that we need to flush the chipset write-buffer when
changing the DMA page tables, to ensure that the change is visible to
the IOMMU.
Override that bit on the affected chipsets, and everything is happy
again.
Thanks to Chris and Bhavesh and others for helping to debug.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Tested-by: Chris Wright <chrisw@sous-sol.org>
Reviewed-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes a number of cases where things were not properly
cleaned up when acpi_check_resource_conflict() returned an error,
causing oopses such as the one reported here:
https://bugzilla.redhat.com/show_bug.cgi?id=483208
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
If the F71882FG chip is at address 0x4e, then the probe at 0x2e will
fail with the following message in the logs:
f71882fg: Not a Fintek device
This is misleading because there is a Fintek device, just at a
different address. So I propose to degrade this message to a debug
message.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The new v4l2_subdev_call used s_fmt instead of g_fmt.
Thanks-to: Andy Walls <awalls@radix.net>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The video_ioctl2 conversion of ivtv in kernel 2.6.27 introduced a bug
causing decoder commands to crash. The decoder commands should have been
handled from the video_ioctl2 default handler, ensuring correct mapping
of the argument between user and kernel space. Unfortunately they ended
up before the video_ioctl2 call, causing random crashes.
Thanks to hannes@linus.priv.at for testing and helping me track down the
cause!
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If a device using the gspca framework is unplugged while it is still streaming
then the call that is used to free the URBs that have been allocated occurs
after the pointer it uses becomes invalid at the end of gspca_disconnect.
Make another cleanup call in gspca_disconnect while the pointer is still
valid (multiple calls are OK as destroy_urbs checks for pointers already
being NULL.
Signed-off-by: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On Mon, 02 Feb 2009, Hartmut wrote:
This change set is wrong. The affected functions cannot be called from
an interrupt context, because they may process large buffers. In this
case, interrupts are disabled for a long time. Functions, like
dvb_dmx_swfilter_packets(), could be called only from a tasklet.
This change set does hide some strong design bugs in dm1105.c and
au0828-dvb.c.
Please revert this change set and do fix the bugs in dm1105.c and
au0828-dvb.c (and other files).
On Sun, 15 Feb 2009, Oliver Endriss wrote:
This changeset _must_ be reverted! It breaks all kernels since 2.6.27
for applications which use DVB and require a low interrupt latency.
It is a very bad idea to call the demuxer to process data buffers with
interrupts disabled!
On Mon, 16 Feb 2009, Trent Piepho wrote:
I agree, this is bad. The demuxer is far too much work to be done with
IRQs off. IMHO, even doing it under a spin-lock is excessive. It should
be a mutex. Drivers should use a work-queue to feed the demuxer.
Thank you for testing this changeset and discovering the issues on it.
Cc: Trent Piepho <xyzzy@speakeasy.org>
Cc: Hartmut <e9hack@googlemail.com>
Cc: Oliver Endriss <o.endriss@gmx.de>
Cc: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch closes one of my todos that was since long on my list.
Some people reported clicks and glitches in the audio stream,
correlated to the LED color changing cycle.
Thanks to Rick Bronson <rick@efn.org>.
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Bob Ross <pigiron@gmx.com>
- correction of stereo detection/setting
- correction of signal strength indicator scaling
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by David Engel <david@istwok.net>, ATSC115 doesn't work
fine with mythtv. This software opens both analog and dvb interfaces of
saa7134.
What happens is that some tuner commands are going to the wrong place,
as shown at the logs:
Feb 12 20:37:48 opus kernel: tuner-simple 1-0061: using tuner params #0 (ntsc)
Feb 12 20:37:48 opus kernel: tuner-simple 1-0061: freq = 67.25 (1076), range = 0, config = 0xce, cb = 0x01
Feb 12 20:37:48 opus kernel: tuner-simple 1-0061: Freq= 67.25 MHz, V_IF=45.75 MHz, Offset=0.00 MHz, div=1808
Feb 12 20:37:48 opus kernel: tuner 1-0061: tv freq set to 67.25
Feb 12 20:37:48 opus kernel: tuner-simple 1-000a: using tuner params #0 (ntsc)
Feb 12 20:37:48 opus kernel: tuner-simple 1-000a: freq = 67.25 (1076), range = 0, config = 0xce, cb = 0x01
Feb 12 20:37:48 opus kernel: tuner-simple 1-000a: Freq= 67.25 MHz, V_IF=45.75 MHz, Offset=0.00 MHz, div=1808
Feb 12 20:37:48 opus kernel: tuner-simple 1-000a: tv 0x07 0x10 0xce 0x01
Feb 12 20:37:48 opus kernel: tuner-simple 1-0061: tv 0x07 0x10 0xce 0x01
This happens due to a hack at TUV1236D analog setup, where it replaces
tuner address, at 0x61 for 0x0a, in order to save a few memory bytes.
The code assumes that nobody else would try to access the tuner during
that setup, but the point is that there's no lock to protect such
access. So, this opens the possibility of race conditions to happen.
Instead of hacking tuner address, this patch uses a temporary var with
the proper tuner value to be used during the setup. This should save
the issue, although we should consider to write some analog/digital
lock at saa7134 driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The devices handled by hid-tmff and hid-zpff were added in the
hid_ignore_list[] instead of hid_blacklist[] in hid-core.c, thus
disabling them completely.
hid_ignore_list[] causes hid layer to skip the device, while
hid_blacklist[] indicates there is a specific driver in hid bus.
Re-enable the devices by moving them to the correct list.
Signed-off-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We can't return immediately because lock_kernel() is held.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
For quite some time users with various UPSes from Powercom were forced to play
magic with bind/unbind in /sys in order to be able to see the UPSes. The
beasts does not work as HID devices, even if claims to do so. cypress_m8
driver works with the devices instead, creating a normal serial port with which
normal UPS controlling software works.
The manufacturer confirmed the upcoming models with proper HID support will
have different device IDs. In any way, it's wrong to have two completely
different modules for one device in kernel.
Blacklist the device in HID (add it to hid_ignore_list) to stop this mess,
finally.
Signed-off-By: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
WARNING: drivers/mfd/built-in.o(.text+0x1706): Section mismatch in
reference from the function sm501_register_gpio() to the function
.devinit.text:sm501_gpio_register_chip()
The function sm501_register_gpio() references
the function __devinit sm501_gpio_register_chip().
This is often because sm501_register_gpio lacks a __devinit
annotation or the annotation of sm501_gpio_register_chip is wrong.
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
drv => driver renaming is needed otherwise modpost will spit false positives
re pointing to __devinit function from regular data.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
The i2c_device_id list is supposed to be zero-terminated.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Balaji Rao <balajirrao@openmoko.org>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The IRQs might have been left enabled in hardware, generating spurious
IRQs before the drivers have registered.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Fixes an off-by-one error in the iomem resource mapping.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Many ARM platforms do not provide a mach/cpu.h so rather than guarding
the use of that header with CONFIG_ARM guard it with the guards used
when testing for the OMAP variants in the body of the code.
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
With a postfix decrement tries will reach -1 rather than 0,
so the warning will not be issued even upon timeout.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
The code is out of sync with the silicon.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Check the return value of the device I/O functions when reading the
ID registers so we can provide a more useful diagnostic when we're
having trouble talking to the device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Ensure that the interrupt handling is configured before we do platform
specific init. This allows the platform specific initialisation to
configure things which use interrupts safely.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Since ei is already known to be non-NULL, I assume that what was intended
was to test the result of kzalloc.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Commit 871af1210f (libata: Add 32bit
PIO support) has caused all kinds of errors on the ATAPI devices, so
it has been empirically proven that one shouldn't try to read/write
an extra data word when a device is not expecting it already. "Don't
do it then"; however, still use a chance to do 32-bit read/write one
last time when there are exactly 3 trailing bytes.
Oh, and stop pointlessly swapping the bytes to and fro on big-endian
machines by using io*_rep() accessors which shouldn't byte-swap.
This patch should fix the kernel.org bug #12609.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is the cause of the DMA faults and disk corruption that people have
been seeing. Some chipsets neglect to report the RWBF "capability" --
the flag which says that we need to flush the chipset write-buffer when
changing the DMA page tables, to ensure that the change is visible to
the IOMMU.
Override that bit on the affected chipsets, and everything is happy
again.
Thanks to Chris and Bhavesh and others for helping to debug.
Should resolve:
https://bugzilla.redhat.com/show_bug.cgi?id=479996http://bugzilla.kernel.org/show_bug.cgi?id=12578
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Tested-and-acked-by: Chris Wright <chrisw@sous-sol.org>
Reviewed-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
bugzilla: #12363
commit 7cd5b08be3 added a second regression:
some Dell's and Compaq's lockup on boot. So we revert most of the code.
The ICH9 reboot issue remains in place and will need some more fixing... :-(
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Fix pci kernel-doc parameter missing notation, correct
function name, and fix typo:
Warning(linux-2.6.28-git10//drivers/pci/pci.c:1511): No description found for parameter 'exclusive'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Hidetoshi Seto points out that commit
bffac3c593 has wrong values in the array.
Rather than correct the array, we can just use a bounds check and
perform the calculation specified in the comment. As a bonus, this will
not run off the end of the array if the device specifies an illegal
value in the MSI capability.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (32 commits)
wimax: fix oops in wimax_dev_get_by_genl_info() when looking up non-wimax iface
net: 4 bytes kernel memory disclosure in SO_BSDCOMPAT gsopt try #2
netxen: fix compile waring "label ‘set_32_bit_mask’ defined but not used" on IA64 platform
bnx2: Update version to 1.9.2 and copyright.
bnx2: Fix jumbo frames error handling.
bnx2: Update 5709 firmware.
bnx2: Update 5706/5708 firmware.
3c505: do not set pcb->data.raw beyond its size
Documentation/connector/cn_test.c: don't use gfp_any()
net: don't use in_atomic() in gfp_any()
IRDA: cnt is off by 1
netxen: remove pcie workaround
sun3: print when lance_open() fails
qlge: bugfix: Add missing rx buf clean index on early exit.
qlge: bugfix: Fix RX scaling values.
qlge: bugfix: Fix TSO breakage.
qlge: bugfix: Add missing dev_kfree_skb_any() call.
qlge: bugfix: Add missing put_page() call.
qlge: bugfix: Fix fatal error recovery hang.
qlge: bugfix: Use netif_receive_skb() and vlan_hwaccel_receive_skb().
...
When compile the latest kernel on IA64 platform,I got a warning:
drivers/net/netxen/netxen_nic_main.c:203: warning: label ‘set_32_bit_mask’
defined but not used
We do not need label ‘set_32_bit_mask’ on IA64 platform,So move it to #else.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If errors are reported on a frame descriptor, we need to
account for the buffer pages that may have been used for this
error packet and recycle them. Otherwise, we may get the wrong
pages for the next packet.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New firmware fixes a data corruption issue when receiving and
placing jumbo frames into host buffers. In some cases, the
buffer descriptor is not updated correctly and this will lead
to the driver linking the wrong number of pages into the SKB.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
