Enable device roles just before starting it.
This way, a single device role should be enough
for all vifs, as we can't use concurrent device
roles (which require ROC) anyway.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
enabled (but not-started) sta role should be good enough
for scanning (both normal and scheduled), so use it
instead of the device_role.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Make debug prints operational when dynamic debug is not defined.
This allows better debugging in production environments.
Change the driver prefix to "wlcore" while were at it.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Allow 3 native mac addresses on 18xx. On 12xx allow 2 native mac
addresses and set the LAA bit to create a third mac address. This
enabled operation with a separate group interface.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
mac80211's resume() callback might get called even if
the sta is not associated (but only up). The
resume sequence in this case results in configuring
the wake-up conditions of a non-started role, which
causes fw assertion.
Fix it by bailing out if the STA is not connected
(like we do on suspend()).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
wowlan filters should be configured in any case in suspend/resume.
This shouldn't be dependent on whether wakeup conditions are the
same for suspend and resume states. Only the FW command to
reconfigure wakeup conditions should be avoided in such a case.
Reported-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Aggregation buffer size is set separately per 18xx/12xx chip family.
For 18xx aggragation buffer is set to 13 pages to utilize all
the available tx/rx descriptors for aggregation.
[Arik - remove redundant parts from the patch]
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Force Tx during the flush if there are packets pending in the driver.
This actually solves a bug where we would get called from the mac80211
wq context, which would prevent tx_work from getting queued, even when
the mutex is unlocked.
Don't stop the queues needlessly if there's nothing to flush. Use a
larger delay when sleeping to give the driver a chance to flush and
avoid cpu busy looping. Re-arrange the loop so the last iteration is
not wasted.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Print how much time a flush took. This will help debug the time it takes
to switch between channels.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
The IEEE80211_TX_CTL_NO_CCK_RATE flag is only set for mgmt packets
transmitted during p2p connection setup. Make sure to use the lowest
OFDM rate guarantee the peer always hears us.
Change the p2p rate policy to contain only the 6mpbs rate to acheive
this effect.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
This solves interoperability issues with peer that don't seem to "hear"
management packets transmitted in higher rates. Based on a previous
patch by Igal Chernobelsky.
Cc: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
recovery_work should be cancelled when stopping the device,
not when removing an interface (this is probably a leftover
from the single-role days)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
When a function requests to recover, it would normally abort and will
not send any additional commands to the HW. However, other threads may
not be aware of the failure and could try to communicate with the HW
after a recovery was queued, but before the recovery work began.
Fix this by introducing an intermediate state which is set when recovery
is queued, and modify all state checks accordingly.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
When a single fw is being used for both single-role
and multi-role cases (e.g. 18xx), wl->mr_fw_name is
NULL, which results in NULL dereference while trying
to load the multi-role fw.
In this case, always use the single-role fw, and avoid
redundant fw switch by checking for this case in
wl12xx_need_fw_change() as well.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
default switch configuration set to pg2 chips (rdl 1/2/3/4).
removed hacks for specific board types.
pg1.x boards are now supported only using module params
or specific conf files.
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Declare any firmware that might be used by this driver.
If all drivers declare their firmware usage, then a sufficiently
complete list of firmware files can then be used to pare down
the external linux-firmware package to just the files in actual use.
Cc: Luciano Coelho <coelho@ti.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Use a module_platform_driver declaration instead of replicating the
init and exit functions in the driver.
Based on the patch for wl18xx by Devendra Naga.
Signed-off-by: Luciano Coelho <luca@coelho.fi>
the driver's init and exit routines can be implemented with the
module_platform_driver, as the init and exit code is same as
that of the module_platform_driver
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
* 'xenarm-for-linus' of git://xenbits.xen.org/people/sstabellini/linux-pvhvm:
arm: introduce a DTS for Xen unprivileged virtual machines
MAINTAINERS: add myself as Xen ARM maintainer
xen/arm: compile netback
xen/arm: compile blkfront and blkback
xen/arm: implement alloc/free_xenballooned_pages with alloc_pages/kfree
xen/arm: receive Xen events on ARM
xen/arm: initialize grant_table on ARM
xen/arm: get privilege status
xen/arm: introduce CONFIG_XEN on ARM
xen: do not compile manage, balloon, pci, acpi, pcpu and cpu_hotplug on ARM
xen/arm: Introduce xen_ulong_t for unsigned long
xen/arm: Xen detection and shared_info page mapping
docs: Xen ARM DT bindings
xen/arm: empty implementation of grant_table arch specific functions
xen/arm: sync_bitops
xen/arm: page.h definitions
xen/arm: hypercalls
arm: initial Xen support
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Whenever both WLAN and BT in/out sleep mode, sometimes WLAN
is not able to take back the shared LNA control after resumes
from sleep mode. The idea is that for WLAN to check if BT owns
LNA control and BT is in sleep mode when WLAN just resumes from
sleep mode. If the condition is true, do a BTCOEX_RC_WARM_RESET
for WLAN to take back the control of shared LNA.
Now the issue is the BT sleep value read from MCI register is
overlooked by assigning u32 into u8. Hence the above condition never
be met so that WLAN used to report beacon losses and frequent
connection drops.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Tested-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mac80211 has formal infrastructure to specify which interface combinations
are supported. Make use of this facility in favor of open coding it
ourselves.
So far we only have to specify we can support multiple AP interfaces,
no other combinations are supported.
Inspired by an earlier patch from Paul Fertser.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All drivers set this value to 1, so there is no need (currently) to let
drivers set this.
Therefor, remove the field; we can always add it back when it is needed.
Inspired by an earlier patch from Paul Fertser.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ap_custom_ie is a struct mwifiex_ie_list which is quite different and
also larger than struct mwifiex_ie. It's a difference between 4196
bytes and 262.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Stone Piao <piaoyun@marvell.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, ASPM is disabled for all WLAN+BT combo chipsets
when BTCOEX is enabled. This is incorrect since the workaround
is required only for WB195, which is a AR9285+AR3011 combo
solution. Fix this by checking for the HW version when enabling
the workaround.
Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Tested-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville says:
====================
Please pull this last(?) batch of fixes intended for 3.6...
For the Bluetooth bits, Gustavo says this:
"Here goes probably my last update to 3.6. It includes the two patches
you were ok last week(from Andrzej Kaczmarek), those are critical
ones, and two other fixes one for a system crash and the other for
a missing lockdep annotation."
The referenced fixes from Andrzej prevent attempts to configure devices
that are powered-off.
Along with the Bluetooth fixes, there are a couple of 802.11 fixes.
Emmanuel Grumbach gives us an iwlwifi fix to prevent releasing an
interrupt twice. Luis R. Rodriguez provides a fix for a possible
circular lock dependency in the cfg80211 regulatory enforcement code.
All of these have been in linux-next for a few days. I hope they are
not too late to make the 3.6 release!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The MIPSsim platform is no longer supported or used. This patch
deletes the Ethernet driver.
Signed-off-by: Steven J. Hill <sjhill@mips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is primarily to address transmission timeout occurrences, when
multiple H/W Tx queues are being used concurrently. Because in
the priority scheduling mode the controller does not service the
Tx queues equally (but in ascending index order), Tx timeouts are
being triggered rightaway for a basic test with multiple simultaneous
connections like:
iperf -c <server_ip> -n 100M -P 8
resulting in kernel trace:
NETDEV WATCHDOG: eth1 (fsl-gianfar): transmit queue <X> timed out
------------[ cut here ]------------
WARNING: at net/sched/sch_generic.c:255
...
and controller reset during intense traffic, and possibly further
complications.
This patch changes the default H/W Tx scheduling setting (TXSCHED)
for multi-queue devices, from priority scheduling mode to a weighted
round robin mode with equal weights for all H/W Tx queues, and
addresses the issue above.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
loopback current mtu of 16436 bytes allows no more than 3 MSS TCP
segments per frame, or 48 Kbytes. Changing mtu to 64K allows TCP
stack to build large frames and significantly reduces stack overhead.
Performance boost on bulk TCP transferts can be up to 30 %, partly
because we now have one ACK message for two 64KB segments, and a lower
probability of hitting /proc/sys/net/ipv4/tcp_reordering default limit.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no such part as KS8001, KS8041 or KS8051. There are only
KSZ8001, KSZ8041 and KSZ8051. Rename these parts as such to match
the Micrel naming.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David J. Choi <david.choi@micrel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Linux ARM kernel <linux-arm-kernel@lists.infradead.org>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ8021 PHY was previously caught by KS8051, which is not correct.
This PHY needs additional setup if it is strapped for address 0. In such
case an reserved bit must be written in the 0x16, "Operation Mode Strap
Override" register. According to the KS8051 datasheet, that bit means
"PHY Address 0 in non-broadcast" and it indeed behaves as such on KSZ8021.
The issue where the ethernet controller (Freescale FEC) did not communicate
with network is fixed by writing this bit as 1.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David J. Choi <david.choi@micrel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the definition of bnx2x_tests_str_arr from static char
pointer to static const char bi-directional array. Also the
bnx2x_get_strings function is simplified.
Reported-by: Joe Perches <joe@perches.com>
Reported-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Merav Sicron <meravs@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware support for MFP is not available in ath5k. Thus,
this implementation allows the mac80211 stack to do the
actuall crypto operation.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously, it was not possible to connect to
networks which requires 11w to be supported by
the stations.
While the documentation hints that there's some
hardware support for offloading MFP "decryption",
this simple implementation relies on the mac80211
stack to do the actual crypto operations.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously, it was not possible to connect to
networks which requires 11w to be supported by
the stations.
Note:
As all current (and old) firmwares corrupt
incoming, protected management frames, the
decryption offloading needs to be disabled.
This will be done automatically if needed.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of copying from a constant array
(which is still needed for other purposes)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Building the libipw component without CONFIG_LIBIPW_DEBUG set triggers this GCC
warning:
drivers/net/wireless/ipw2x00/libipw_wx.c:526:21: warning: unused variable 'dev' [-Wunused-variable]
The cause of this warning is that, without CONFIG_LIBIPW_DEBUG set,
LIBIPW_DEBUG_WX compiles away. Fix it by substituting ieee->dev for (its
equivalent) dev.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently scan operation is delayed/aborted based on Tx traffic
consistency. This decision is taken after receiving scan
response of first scan command from FW. But when heavy traffic
is running, we can not even afford to send first scan command
and go off channel for 30msec. We will block scan request in
this case.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By default, device is disconnected before entering suspend state.
User can keep the connection alive by using module parameter
"disconect_on_suspend=0".
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Field 'pub' in struct brcmf_cfg80211_priv was types as void pointer
and filled with parameter passed in brcmf_cfg80211_attach(). This
patch makes the type specific, ie. struct brcmf_pub.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Small step to fix structure commenting using kernel-doc syntax.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On a usb error the lock bit should be cleared.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug when device is being started
while RfKill switch is engaged, leading to hang
due to partial initialization of hardware.
Tested-by: <dragonn@op.pl>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
clean up code.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug in routine where phy bands are determined.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
clean up code.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SDIO read non-glomming frame routine handles first frame and
follow up frame read separately. But they share a lot of common
code. This patch abstracts a brcmf_sdio_hdparser function and
optimize the code flow for better readability and future
optimization.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For suspend/resume it is necessary to store firmware in memory.
In order to support multiple usb dongles at the same time a linked
list of firmwares was created.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some events result in printing of the buffer when debug is
enabled. This printing was not very efficient. Changed to
macro so it comes out nice and clean without filling log buffer.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This change add support for NL80211 scheduled scan. This may be used to
offload scanning to the device, which may give the host opportunity to
sleep. The newer versions of wpa_supplicant have support for this
functionality.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the introduction of E-Scan there are two scan mechanisms
in the driver. I-Scan was aborted on suspend and bringing down
the device using brcmf_term_iscan(). The function has been
renamed to brcmf_abort_scanning() and covers e-scan abort as
well.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the introduction of e-scan mechanism in brcmfmac
(e756af5 brcmfmac: add e-scan support.) a couple of sparse
warnings were introduced. This patch resolves those.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When delayed scan operation is resumed, we just add next scan
command in queue but don't wakeup main thread to process the
command. Hence the command is downloaded to firmware only after
waking up the main thread by any other means.
This bug which was introduced after "mwifiex: improve scan delay
logic.." patch is fixed here.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Setting of the individual fields of the RF register can be simplified.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move RT3290 BBP initialization sequence (part) to the right place in the code.
This is just a code style change, no functional changes.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Align with the values used by the RT3572 Ralink vendor driver v2.5.0.0.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make the code in rt2800_get_default_vgc more understandable and
readable, especially for the 5GHz band values.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a new callback to handle WLAN RX diversity for
AR9565.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set main_gaintb and alt_gaintb once instead of zero'ing them
in every case.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of trying to determine whether antenna diversity is
enabled by parsing eeprom data, use ATH9K_HW_CAP_ANT_DIV_COMB
which is already filled at init time.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the 'hw_timer_enabled' to 'false' wherever we are stopping
hardware generic timers, excecpt the case where we start them
again immediately.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Upon handling an e-scan result event from the firmware in
brcmf_cfg80211_escan_handler() the status may indicate e-scan
is completed or aborted. If so brcmf_notify_escan_complete()
is called. However, that function and brcmf_cfg80211_escan_handler()
both log the same debug message and both enable MPC flag in the
firmware.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch assures data is only appended in output buffer when
data is not NULL and datalen is not zero.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes bug where driver frees resources twice when
an exception occurs.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SDIO in-band interrupt is level sensitive according to SDIO standard.
When the register interrupt handler gets called by SDIO stack it is
running in non interrupt context and expected to clear the interrupt
from the dongle. Therefore in-band and out-of-band interrupt need to
be handled differently.
Cc: Wei Ni <wni@nvidia.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Reported-by: Wei Ni <wni@nvidia.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use SDIO host lock to protect the entire communication process
of register access or data read/write rather than function calls
to MMC/SDIO stack only. This can help to avoid unintentional
memory access and unexpected interruption.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Switch SDIO dpc implementation from kernel thread to workqueue for
better performance and compatibility.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Interrupt pending flag used in SDIO bus layer could be used in
multiple processes in different context. Use atomic_t make sure
every interrupt is handled.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove sdio bus sleep mechanism since it is never invoked.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmf_sendpkt only called by brcmf_netdev_start_xmit now. Absorb it
to increase readability.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Inside ath9k_hif_usb_firmware_fail(), the instance of
'struct struct hif_device_usb' may be freed by
ath9k_hif_usb_disconnect() after
complete(&hif_dev->fw_done);
But 'hif_dev' is still accessed after the line code
above is executed.
This patch fixes the issue by not accessing 'hif_dev'
after 'complete(&hif_dev->fw_done)' inside
ath9k_hif_usb_firmware_fail().
Cc: ath9k-devel@lists.ath9k.org
Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Right now MCI work is being queued twice by profile and status
updation. Queue MCI work once when it is needed.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ensure that led pin is filled and set to OFF before starting
the driver. With recent changes, drv_start is being called even
before led_init is being completed. This is causing led is always
OFF on driver load when the interface is UP. This patch splits the
led init and fills the led pin before register hw.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update all coex parameters in sigle place. So that we can avoid
redoing the same operation in mutiple places and it eases debugging.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before processing BT profiles or status messages, check whether
it is requested to flush BT profile. Otherwise it might increase
number of BT profiles that affects the WLAN performance. Also
flush the profiles when MCI is recovering from broken rx. After
flushing BT profiles, query BT topology to refetch them.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the 9462 is operating in 2G mode and MCI is enabled then
reduce the selfgen chain mask to chain 1. Otherwise poor performance
was reported at short range at Rx side when COEX is enabled.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During fast channel change, perform 2g5g_switch before starting
noisefloor calibration to avoid nfload timeout.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set the driver specific SGI flag based on the station's
HT capabilities, otherwise rate control uses the wrong rate.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With recent kernel changes we can now return errors on a failure to setup a
VLAN filter. This patch takes advantage of that opportunity so that we can
return either an EIO error in the case of a mailbox failure, or an EACCESS
error in the case of being denied access to the VLAN filter table by the
PF.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Robert Garrett <robertx.e.garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change fixes the ixgbevf driver so that it can correctly drop a frame
should it receive a jumbo frame.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
While fixing up a patch from Alex Duyck to use q_vectors in ring containers
to update the ITR I bungled it and missed actually updating the counters
in the ring container q_vectors. This patch fixes my mistake and makes
interrupt moderation actually work.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove 'rx_ring' parameter as it is not used in ixgbevf_receive_skb
Signed-off-by: Narendra K <narendra_k@dell.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The counter is not valid unless the controller is running in IOV mode.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The VF driver was not designed to correctly handle a message timeout. As
a result it is possible for one bad message to invalidate all messages
following it until the part is reset. Instead we should copy the example
in igbvf of how to handle a mailbox event and message timeout.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We're now using isa_virt_to_bus(), and there really
isn't a generic and consistent test for whether a
platform provides this interface or not.
This driver is also for an x86-only device.
Signed-off-by: David S. Miller <davem@davemloft.net>
When PPPOE is running over a virtual ethernet interface (e.g., a
bonding interface) and the user tries to delete the interface in case
the PPPOE state is ZOMBIE, the kernel will loop forever while
unregistering net_device for the reference count is not decreased to
zero which should have been done with dev_put().
Signed-off-by: Xiaodong Xu <stid.smth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some hw, link is not up during adding iface to team. That causes event
not being sent to userspace and that may cause confusion.
Fix this bug by sending port changed event once it's added to team.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
PTP Hardware Clock devices appear as class devices in sysfs. This patch
changes the registration API to use the parent device, clarifying the
clock's relationship to the underlying device.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
This series contains updates to igb only.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the driver has no MODULE_LICENSE attribute in its source which
results in a kernel taint if I load this:
root@(none):~# modprobe bcm87xx
bcm87xx: module license 'unspecified' taints kernel.
Since the first lines of the source code clearly state:
* This file is subject to the terms and conditions of the GNU General
* Public License. See the file "COPYING" in the main directory of this
* archive for more details.
I think it's safe to add the MODULE_LICENSE("GPL") macro and thus remove
the kernel taint.
Cc: stable@vger.kernel.org
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
One-shot mode uses the TCS bit of the status register to discern
whether a transmission was successful or not. On a failed
transmission, the frame is not echoed back.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
__iomem annotation cleanup branch from Arnd.
* cleanup/__iomem: (21 commits)
net: seeq: use __iomem pointers for MMIO
video: da8xx-fb: use __iomem pointers for MMIO
scsi: eesox: use __iomem pointers for MMIO
serial: ks8695: use __iomem pointers for MMIO
input: rpcmouse: use __iomem pointers for MMIO
ARM: samsung: use __iomem pointers for MMIO
ARM: spear13xx: use __iomem pointers for MMIO
ARM: sa1100: use __iomem pointers for MMIO
ARM: prima2: use __iomem pointers for MMIO
ARM: nomadik: use __iomem pointers for MMIO
ARM: msm: use __iomem pointers for MMIO
ARM: lpc32xx: use __iomem pointers for MMIO
ARM: ks8695: use __iomem pointers for MMIO
ARM: ixp4xx: use __iomem pointers for MMIO
ARM: iop32x: use __iomem pointers for MMIO
ARM: iop13xx: use __iomem pointers for MMIO
ARM: integrator: use __iomem pointers for MMIO
ARM: imx: use __iomem pointers for MMIO
ARM: ebsa110: use __iomem pointers for MMIO
ARM: at91: use __iomem pointers for MMIO
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This change is meant to improve performance on systems that do not require
the DMA unmap calls. On those systems we do not need to make use of the
unmap address for Tx or the unmap length so we can drop both thereby
reducing the size of the Tx buffer info structure.
In addition I have changed the logic to check for unmap length instead of
unmap address when checking to see if a buffer needs to be unmapped from
DMA use. The reasons for this change is that on some platforms it is
possible to receive a valid DMA address of 0 from an IOMMU.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of storing the RSS key as a character array we can simplify the
configuration by making it a u32 array. This allows us to just write one
value per register without any unnecessary operations to construct the
value.
This change will produce the same exact key, the only difference is that I
translated the u8 array to a u32 array which will be correctly ordered on
writes to hardware by the cpu_to_le32 operations that are built into the
writel calls.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up our RSS indirection table configuration so that we
generate the same table regardless of CPU endianness. In addition it
changes the table setup so that instead of doing a modulo based setup it is
instead a divisor based setup. The advantage to this is that we should be
able to take the Rx hash and compute the Rx queue with very little CPU
overhead if needed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that Tx cleanup is done in a do/while loop instead
of a for loop. The main motivation behind this is the fact that we should
never be invoked with a budget less than 1 so we can skip checking the
budget before processing the first descriptor.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change removes the code that was doing the NUMA allocations for the
q_vectors, rings, and ring resources. The problem is the logic used assumed
that the NUMA nodes were always interleved and that is not always the case.
At some point I hope to add this functionality back in a more controlled
manner in the future.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Due to a hardware issue, on i210 and i211 parts, the TNCRS statistic
provides an invalid value. This patch changes the update stats function
to increment the stat only for non-i210/i211 parts.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adapt the pre-existing and assigned VFs code to the ixgbe way introduced
in commit 9297127b9c.
Instead of searching the enabled VFs we use pci_num_vf to determine enabled VFs.
By comparing to which PF an assigned VF is owned it's possible to decide
whether to leave it enabled or not.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Robert Garrett <robertx.e.garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In case of error, the function clk_get() returns ERR_PTR()
and never returns NULL pointer. The NULL test in the error
handling should be replaced with IS_ERR().
dpatch engine is used to auto generated this patch.
(https://github.com/weiyj/dpatch)
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Rename generic-sounding function dump_mem() to pcan_dump_mem()
so that it does not conflict with the dump_mem() function in
arch/sh/include/asm/kdebug.h.
drivers/net/can/usb/peak_usb/pcan_usb_core.c: error: conflicting types for 'dump_mem': => 56:6
drivers/net/can/usb/peak_usb/pcan_usb_core.h: error: conflicting types for 'dump_mem': => 134:6
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
[mkl: convert all users of dump_mem(), too]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Adopt pinctrl support to c_can driver based on c_can device
pointer, pinctrl driver configure SoC pins to d_can mode
according to definitions provided in .dts file.
In device specific device tree file 'pinctrl-names = "default";'
and 'pinctrl-0 = <&d_can1_pins>;' needs to add to configure pins
from c_can driver. d_can1_pins node contains the pinmux/config
details of d_can L/H pins.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Adds suspend resume support to DCAN driver which enables
DCAN power down mode bit (PDR). Then DCAN will ack the local
power-down mode by setting PDA bit in STATUS register.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add Runtime PM support to C_CAN/D_CAN controller. The runtime PM
APIs control clocks for C_CAN/D_CAN IP and prevent access to the
register of C_CAN/D_CAN IP when clock is turned off.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add device tree support to C_CAN/D_CAN controller and usage details
are added to device tree documentation. Driver was tested on AM335x
EVM.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
For the of binding doc:
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Modify c_can device names from *_CAN_DEVTYPE to BOSCH_*_CAN to make
use of same names for array indexes in c_can_id_table[] as well as
device names.
This patch also add indexes to c_can_id_table array.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Pull networking updates from David Miller:
"More bug fixes, nothing gets past these guys"
1) More kernel info leaks found by Mathias Krause, this time in the
IPSEC configuration layers.
2) When IPSEC policies change, we do not properly make sure that cached
routes (which could now be stale) throughout the system will be
revalidated. Fix this by generalizing the generation count
invalidation scheme used by ipv4. From Nicolas Dichtel.
3) When repairing TCP sockets, we need to allow to restore not just the
send window scale, but the receive one too. Extend the existing
interface to achieve this in a backwards compatible way. From
Andrey Vagin.
4) A fix for FCOE scatter gather feature validation erroneously caused
scatter gather to be disabled for things like AOE too. From Ed L
Cashin.
5) Several cases of mishandling of error pointers, from Mathias Krause,
Wei Yongjun, and Devendra Naga.
6) Fix gianfar build, from Richard Cochran.
7) CAP_NET_* failures should return -EPERM not -EACCES, from Zhao
Hongjiang.
8) Hardware reset fix in janz-ican3 CAN driver, from Ira W Snyder.
9) Fix oops during rmmod in ti_hecc CAN driver, from Marc Kleine-Budde.
10) The removal of the conditional compilation of the clk support code
in the stmmac driver broke things. This is because the interfaces
used are the ones that don't also perform the enable/disable of the
clk. Fix from Stefan Roese.
11) The QFQ packet scheduler can record out of range virtual start
times, resulting later in misbehavior and even crashes. Fix from
Paolo Valente.
12) If MSG_WAITALL is used with IOAT DMA under TCP, we can wedge the
receiver when the advertised receive window goes to zero. Detect
this case and force the processing of the IOAT DMA queue when it
happens to avoid getting stuck. Fix from Michal Kubecek.
13) batman-adv assumes that test_bit() returns only 0 or 1, but this is
not true for x86 (which returns -1 or 0, via the 'sbb' instruction).
Fix from Linus Lussing.
14) Fix small packet corruption in e1000, from Tushar Dave.
15) make_blackhole() in the IPSEC policy code can do one read unlock too
many, fix from Li RongQing.
16) The new tcp_try_coalesce() code introduced a bug in TCP URG
handling, fix from Eric Dumazet.
17) Fix memory leak in __netif_receive_skb() when doing zerocopy and
when hit an OOM condition. From Michael S Tsirkin.
18) netxen blindly deferences pdev->bus->self, which is not guarenteed
to be non-NULL. Fix from Nikolay Aleksandrov.
19) Fix a performance regression caused by mistakes in ipv6 checksum
validation in the bnx2x driver, fix from Michal Schmidt.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (45 commits)
net/stmmac: Use clk_prepare_enable and clk_disable_unprepare
net: change return values from -EACCES to -EPERM
net/irda: sh_sir: fix return value check in sh_sir_set_baudrate()
stmmac: fix return value check in stmmac_open_ext_timer()
gianfar: fix phc index build failure
ipv6: fix return value check in fib6_add()
bnx2x: remove false warning regarding interrupt number
can: ti_hecc: fix oops during rmmod
can: janz-ican3: fix support for older hardware revisions
net: do not disable sg for packets requiring no checksum
aoe: assert AoE packets marked as requiring no checksum
at91ether: return PTR_ERR if call to clk_get fails
xfrm_user: don't copy esn replay window twice for new states
xfrm_user: ensure user supplied esn replay window is valid
xfrm_user: fix info leak in copy_to_user_tmpl()
xfrm_user: fix info leak in copy_to_user_policy()
xfrm_user: fix info leak in copy_to_user_state()
xfrm_user: fix info leak in copy_to_user_auth()
net: qmi_wwan: adding Huawei E367, ZTE MF683 and Pantech P4200
tcp: restore rcv_wscale in a repair mode (v2)
...
Commit eb716c54b1 ("sunbmac: remove
unnecessary setting of skb->dev") caused the local varible 'dev'
in bigmac_init_rings to become unused. And now the compiler
warns about it.
Signed-off-by: David S. Miller <davem@davemloft.net>
On some hw, link is not up during adding iface to team. That causes event
not being sent to userspace and that may cause confusion.
Fix this bug by sending port changed event once it's added to team.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an issue introduced by commit ID 6a81c26f
[net/stmmac: remove conditional compilation of clk code], which
switched from the internal stmmac_clk_{en}{dis}able calls to
clk_{en}{dis}able. By this, calling clk_prepare and clk_unprepare
was removed.
clk_{un}prepare is mandatory for platforms using common clock framework.
Since these drivers are used by SPEAr platform, which supports common
clock framework, add clk_{un}prepare() support for them. Otherwise
the clocks are not correctly en-/disabled and ethernet support doesn't
work.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde says:
====================
two patches for the v3.6 release cycle. Ira W. Snyder fixed support for the
older version of the Janz CMOD-IO Carrier Board. I found and fixed an oops in
the ti_hecc driver, which occurs when removing the module if the network
interface is still open.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error, the function clk_get() returns ERR_PTR()
and never returns NULL pointer. The NULL test in the error
handling should be replaced with IS_ERR().
dpatch engine is used to auto generated this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error, the function clk_get() returns ERR_PTR()
and never returns NULL pointer. The NULL test in the error
handling should be replaced with IS_ERR().
dpatch engine is used to auto generated this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a build failure introduced in commit 66636287
("gianfar: Support the get_ts_info ethtool method."). Not only was a
global variable inconsistently named, but also it was not exported as
it should have been.
This fix is also needed in stable version 3.5.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since version 7.4 the FW configures in the pci config space the max
number of interrupts available to the physical function, instead of
the exact number to use.
This causes a false warning in driver when comparing the number of
configured interrupts to the number about to be used.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the modes of Huawei E367 has this QMI/wwan interface:
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=07 Driver=(none)
E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
Huawei use subclass and protocol to identify vendor specific
functions, so adding a new vendor rule for this combination.
The Pantech devices UML290 (106c:3718) and P4200 (106c:3721) use
the same subclass to identify the QMI/wwan function. Replace the
existing device specific UML290 entries with generic vendor matching,
adding support for the Pantech P4200.
The ZTE MF683 has 6 vendor specific interfaces, all using
ff/ff/ff for cls/sub/prot. Adding a match on interface #5 which
is a QMI/wwan interface.
Cc: Fangxiaozhi (Franko) <fangxiaozhi@huawei.com>
Cc: Thomas Schäfer <tschaefer@t-online.de>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Shawn J. Goff <shawn7400@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since Xen-4.2, hvm domains may have portions of their memory paged out. When a
foreign domain (such as dom0) attempts to map these frames, the map will
initially fail. The hypervisor returns a suitable errno, and kicks an
asynchronous page-in operation carried out by a helper. The foreign domain is
expected to retry the mapping operation until it eventually succeeds. The
foreign domain is not put to sleep because itself could be the one running the
pager assist (typical scenario for dom0).
This patch adds support for this mechanism for backend drivers using grant
mapping and copying operations. Specifically, this covers the blkback and
gntdev drivers (which map foreign grants), and the netback driver (which copies
foreign grants).
* Add a retry method for grants that fail with GNTST_eagain (i.e. because the
target foreign frame is paged out).
* Insert hooks with appropriate wrappers in the aforementioned drivers.
The retry loop is only invoked if the grant operation status is GNTST_eagain.
It guarantees to leave a new status code different from GNTST_eagain. Any other
status code results in identical code execution as before.
The retry loop performs 256 attempts with increasing time intervals through a
32 second period. It uses msleep to yield while waiting for the next retry.
V2 after feedback from David Vrabel:
* Explicit MAX_DELAY instead of wrap-around delay into zero
* Abstract GNTST_eagain check into core grant table code for netback module.
V3 after feedback from Ian Campbell:
* Add placeholder in array of grant table error descriptions for unrelated
error code we jump over.
* Eliminate single map and retry macro in favor of a generic batch flavor.
* Some renaming.
* Bury most implementation in grant_table.c, cleaner interface.
V4 rebased on top of sync of Xen grant table interface headers.
Signed-off-by: Andres Lagar-Cavilla <andres@lagarcavilla.org>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
[v5: Fixed whitespace issues]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The Revision 1.0 Janz CMOD-IO Carrier Board does not have support for
the reset registers. To support older hardware, the code is changed to
use the hardware reset register on the Janz VMOD-ICAN3 hardware itself.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
socfpga, picoxcell, and vexpress.
Multi-platform support is dependent on mach/gpio.h removal and
restructuring of DEBUG_LL and dtb build rules included in this branch.
This has been built for all defconfigs, and booted on highbank with
all 5 platforms enabled.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQU4miAAoJEMhvYp4jgsXi1vMH/A4JJXe24cyo31rHJspZDSFg
nnCbnGKfDEOIHwLA8C3OeJuhswMlP/vWlGC512QXL8903XpZ2VJe63f2CLo1mN7Z
hg3JPWrp2VXZ/bqdMnUcw2CtlylrhyG9MUPapkcp+5Agjz2lwaJtRNL6LRRQX4Ei
cWjsJtaFpRj1QraFna0hpTQNO640je6s1rAIJl6eNOuX08l12ZAGDUA+IUUsa1cA
0OGeOAjH6gmkpMI89j1VPPKVRLHIdP4QcxmAZCHJ2LtvylyrlmYskctpAYibobvt
JPLnZgzMFAegnWtJhOYodhBJlfyypEeh2fsZVyDPowqRz9vaAWRjs6u/I4GYaME=
=HR3H
-----END PGP SIGNATURE-----
Merge tag 'multi-platform-for-3.7' of git://sources.calxeda.com/kernel/linux into next/multiplatform
Enable initial ARM multi-platform support for highbank, mvebu,
socfpga, picoxcell, and vexpress.
Multi-platform support is dependent on mach/gpio.h removal and
restructuring of DEBUG_LL and dtb build rules included in this branch.
This has been built for all defconfigs, and booted on highbank with
all 5 platforms enabled.
By Rob Herring (18) and Arnd Bergmann (1)
via Rob Herring
* tag 'multi-platform-for-3.7' of git://sources.calxeda.com/kernel/linux:
ARM: vexpress: convert to multi-platform
ARM: initial multiplatform support
ARM: mvebu: move armada-370-xp.h in mach dir
ARM: vexpress: remove dependency on mach/* headers
ARM: picoxcell: remove dependency on mach/* headers
ARM: move all dtb targets out of Makefile.boot
ARM: picoxcell: move debug macros to include/debug
ARM: socfpga: move debug macros to include/debug
ARM: mvebu: move debug macros to include/debug
ARM: vexpress: move debug macros to include/debug
ARM: highbank: move debug macros to include/debug
ARM: move debug macros to common location
ARM: make mach/gpio.h headers optional
ARM: orion: move custom gpio functions to orion-gpio.h
ARM: shmobile: move custom gpio functions to sh-gpio.h
ARM: pxa: use gpio_to_irq for sharppm_sl
net: pxaficp_ir: add irq resources
usb: pxa27x_udc: remove IRQ_USB define
staging: ste_rmi4: remove gpio.h include
Conflicts due to addition of bcm2835 and removal of pnx4008 in:
arch/arm/Kconfig
arch/arm/Makefile
Conflicts due to new dtb targets, moved to arch/arm/boot/dts/Makefile in:
arch/arm/mach-imx/Makefile.boot
arch/arm/mach-mxs/Makefile.boot
arch/arm/mach-tegra/Makefile.boot
Signed-off-by: Olof Johansson <olof@lixom.net>
The Tegra code-base has contained both a legacy DMA and a dmaengine
driver since v3.6-rcX. This series flips Tegra's defconfig to enable
dmaengine rather than the legacy driver, and removes the legacy driver
and all client code.
The branch is based on v3.6-rc6 in order to pick up a bug-fix to the
ASoC Tegra PCM driver that's required for audio to work correctly when
using dmaengine.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=4eRL
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.7-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/cleanup
ARM: tegra: switch to dmaengine
The Tegra code-base has contained both a legacy DMA and a dmaengine
driver since v3.6-rcX. This series flips Tegra's defconfig to enable
dmaengine rather than the legacy driver, and removes the legacy driver
and all client code.
* tag 'tegra-for-3.7-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ASoC: tegra: remove support of legacy DMA driver based access
spi: tegra: remove support of legacy DMA driver based access
ARM: tegra: apbio: remove support of legacy DMA driver based access
ARM: tegra: dma: remove legacy APB DMA driver
ARM: tegra: config: enable dmaengine based APB DMA driver
+ sync to 3.6-rc6
Jeff Kirsher says:
====================
This series contains updates to igb and ixgbevf.
v2: updated patch description in 04 patch (ixgbevf: scheduling while
atomic in reset hw path)
...
Akeem G. Abodunrin (1):
igb: Support to enable EEE on all eee_supported devices
Alexander Duyck (2):
igb: Remove artificial restriction on RQDPC stat reading
ixgbevf: Add support for VF API negotiation
John Fastabend (1):
ixgbevf: scheduling while atomic in reset hw path
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
we are currently returning ENODEV, as the clk_get may give a exact
error code in its returned pointer, assign it to the ret by using the
PTR_ERR function, so that the subsequent goto label will jump to the
error path and clean the driver and return the error correctly.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary temporary variable and #ifdef DEBUG block.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the modes of Huawei E367 has this QMI/wwan interface:
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=07 Driver=(none)
E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
Huawei use subclass and protocol to identify vendor specific
functions, so adding a new vendor rule for this combination.
The Pantech devices UML290 (106c:3718) and P4200 (106c:3721) use
the same subclass to identify the QMI/wwan function. Replace the
existing device specific UML290 entries with generic vendor matching,
adding support for the Pantech P4200.
The ZTE MF683 has 6 vendor specific interfaces, all using
ff/ff/ff for cls/sub/prot. Adding a match on interface #5 which
is a QMI/wwan interface.
Cc: Fangxiaozhi (Franko) <fangxiaozhi@huawei.com>
Cc: Thomas Schäfer <tschaefer@t-online.de>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Shawn J. Goff <shawn7400@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dbg() USB macro is so old, it predates me. The USB networking drivers are
the last hold-out using this macro, and we want to get rid of it, so replace
the usage of it with the proper netdev_dbg() or dev_dbg() (depending on the
context) calls.
Some places we end up using a local variable for the debug call, so also
convert the other existing dev_* calls to use it as well, to save tiny amounts
of code space.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings says:
====================
1. Extension to PPS/PTP to allow for PHC devices where pulses are
subject to a variable but measurable delay.
2. PPS/PTP/PHC support for Solarflare boards with a timestamping
peripheral.
3. MTD support for updating the timestamping peripheral on those boards.
4. Fix for potential over-length requests to firmware.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Before Emmanuel's change to use a copy of the command
("iwlwifi: get the correct HCMD in the response handler")
the iwl_add_sta_callback() function would have used a
random pointer to somewhere when processing responses
to an async command, while that wasn't valid data it
was at least a valid pointer. Now, the pointer will be
NULL in this case, thus crashing.
Fix this by exiting the function early if no command
is passed back which means it was sent asynchronously.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This change makes it so that the VF can support the PF/VF API negotiation
protocol. Specifically in this case we are adding support for API 1.0
which will mean that the VF is capable of cleaning up buffers that span
multiple descriptors without triggering an error.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Current implementation enables EEE on only i350 device. This patch enables
EEE on all eee_supported devices. Also, configured LPI clock to keep
running before EEE is enabled on i210 and i211 devices.
Signed-off-by: Akeem G. Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For some reason the reading of the RQDPC register was being artificially
limited to 4K. Instead of limiting the value we should read the value and
add the full amount. Otherwise this can lead to a misleading number of
dropped packets when the actual value is in fact much higher.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The r8169 driver currently limits the DMA burst for TX to 1024 bytes. I have
a box where this prevents the interface from using the gigabit line to its full
potential. This patch solves the problem by setting TX_DMA_BURST to unlimited.
The box has an ASRock B75M motherboard with on-board RTL8168evl/8111evl
(XID 0c900880). TSO is enabled.
I used netperf (TCP_STREAM test) to measure the dependency of TX throughput
on MTU. I did it for three different values of TX_DMA_BURST ('5'=512, '6'=1024,
'7'=unlimited). This chart shows the results:
http://michich.fedorapeople.org/r8169/r8169-effects-of-TX_DMA_BURST.png
Interesting points:
- With the current DMA burst limit (1024):
- at the default MTU=1500 I get only 842 Mbit/s.
- when going from small MTU, the performance rises monotonically with
increasing MTU only up to a peak at MTU=1076 (908 MBit/s). Then there's
a sudden drop to 762 MBit/s from which the throughput rises monotonically
again with further MTU increases.
- With a smaller DMA burst limit (512):
- there's a similar peak at MTU=1076 and another one at MTU=564.
- With unlimited DMA burst:
- at the default MTU=1500 I get nice 940 Mbit/s.
- the throughput rises monotonically with increasing MTU with no strange
peaks.
Notice that the peaks occur at MTU sizes that are multiples of the DMA burst
limit plus 52. Why 52? Because:
20 (IP header) + 20 (TCP header) + 12 (TCP options) = 52
The Realtek-provided r8168 driver (v8.032.00) uses unlimited TX DMA burst too,
except for CFG_METHOD_1 where the TX DMA burst is set to 512 bytes.
CFG_METHOD_1 appears to be the oldest MAC version of "RTL8168B/8111B",
i.e. RTL_GIGA_MAC_VER_11 in r8169. Not sure if this MAC version really needs
the smaller burst limit, or if any other versions have similar requirements.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The internal functions for add/deleting addresses don't change
their argument.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building 64-bit kernel with this driver we get following warnings from
the compiler:
drivers/net/ethernet/i825xx/znet.c: In function ‘hardware_init’:
drivers/net/ethernet/i825xx/znet.c:863:29: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/net/ethernet/i825xx/znet.c:870:29: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
Fix these by calling isa_virt_to_bus() before passing the pointers to
set_dma_addr().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ARM is moving to stricter checks on readl/write functions,
so we need to use the correct types everywhere.
Cc: netdev@vger.kernel.org
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Instead of memcpy() from a static array, just use
the new helper function eth_broadcast_addr().
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
MCDI supports requests up to 252 bytes long, which is only enough to
pass 63 RX queue IDs to MC_CMD_FLUSH_RX_QUEUES. However a VF may have
up to 64 RX queues, and if we try to flush them all we will generate
an over-length request and BUG() in efx_mcdi_copyin(). Currently
all VF drivers limit themselves to 32 RX queues, so reducing the
limit to 63 does no harm.
Also add a BUILD_BUG_ON in efx_mcdi_flush_rxqs() so we remember to
deal with the same problem there if EFX_MAX_CHANNELS is increased.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
On big-endian systems the MTD partition names currently have mangled
subtype numbers and are not recognised by the firmware update tool
(sfupdate).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Add PTP IEEE-1588 support and make accesible via the PHC subsystem.
This work is based on prior code by Andrew Jackson
Signed-off-by: Stuart Hodgson <smhodgson@solarflare.com>
[bwh:
- Add byte order conversion in efx_ptp_send_times()
- Simplify conversion of PPS event times
- Add the built-in vs module check to CONFIG_SFC_PTP dependencies]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The maximum array sizes have been calculated on the basis of a maximum
SDU size of 255 bytes, whereas the actual maximum is 252 bytes.
Constructing a larger SDU will result in a BUG_ON in efx_mcdi_copyin.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
When the driver can't get the HW ready, we would release
the interrupt twice which made the kernel complain loudly.
Cc: stable@vger.kernel.org
Reported-by: Brian Cockrell <brian.cockrell@intel.com>
Tested-by: Brian Cockrell <brian.cockrell@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On PCI/PCI-X HW, if packet size is less than ETH_ZLEN,
packets may get corrupted during padding by HW.
To WA this issue, pad all small packets manually.
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a check if pdev->bus->self == NULL (root bus). When attaching
a netxen NIC to a VM it can be on the root bus and the guest would
crash in netxen_mask_aer_correctable() because of a NULL pointer
dereference if CONFIG_PCIEAER is present.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d6cb3e41 "bnx2x: fix checksum validation" caused a performance
regression for IPv6. Rx checksum offload does not work. IPv6 packets
are passed to the stack with CHECKSUM_NONE.
The hardware obviously cannot perform IP checksum validation for IPv6,
because there is no checksum in the IPv6 header. This should not prevent
us from setting CHECKSUM_UNNECESSARY.
Tested on BCM57711.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Couple more IPoIB fixes for regressions introduced by path database conversion
- Minor other fixes to low-level drivers (cxgb4, mlx4, qib, ocrdma)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABCAAGBQJQV0eiAAoJEENa44ZhAt0hTScP/3+Y8v4w3Nyop7iNj9uvnsCn
PhgfY9XUp9d0zOHM7XK+pTGLJheLLiyXfcCFTwgoC6tIyj7J1ulhYv+RBr7GbS+e
K7aG7QtLDyM17ETgOBVIAvkz1CFKwdI843xRQKo0/oVMQJ9XLHg0nvzd+XaxZuud
C+7Lfl5RH9Bl1tHJuOZmdyJinSQyLO/uV+tqwL5upF5YMTCJ2XsmVa1HQKhOAkBE
bH4zXtFViNEKVuKXkpGc1yJFKZiwysirluYXedDkkEdr2jf9Mysw5JvZKVUOCh+4
qYMjEAWQaUBia/tFUs9k6iCwE8ws7tRC4OSisb3cVzCUaqkfmx1Sp7vAQcDqx4xB
r2dy4oc+vEFdrmjerOVEgmdgTwnDrWMjUlPuGyRX9935I7ybKA7NQPGlImKU8oiq
8vyptsTN6r7AYc7kw6aYaE9kqGPnST7I3cZg71lHfwCuHKMNYfkxd1Mqxx/W6rMZ
G1VnstVdioQK2HvcFIeArXQ6H6QjUAY92WMoyhIsrU4KwEx2Zpr0pfKWCD0eIOuB
f4s9v0f5/6DqSwJ9uhhpAW/5bmV+RUCDjm8Ep9i70bGk7SliwT0MNPhHbaMfm7aU
c+awy3HWpWKGCtod9zUzJH/4NsHzpggdHUlyAOuU5nqsh9GarYb0cvLjTNfsfdyV
haQtMR+fSUK7Durd9MQl
=nqvR
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull InfiniBand/RDMA fixes from Roland Dreier:
- A couple more IPoIB fixes for regressions introduced by path database
conversion
- Minor other fixes to low-level drivers (cxgb4, mlx4, qib, ocrdma)
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/qib: Fix failure of compliance test C14-024#06_LocalPortNum
RDMA/ocrdma: Fix CQE expansion of unsignaled WQE
mlx4_core: Fix integer overflows so 8TBs of memory registration works
IPoIB: Fix AB-BA deadlock when deleting neighbours
IPoIB: Fix memory leak in the neigh table deletion flow
RDMA/cxgb4: Move dereference below NULL test
Previously I210/I211 followed the same code flow as 82580/I350 for 1588.
However, since the register sets have changed, we must update the
implementation to accommodate the register changes.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In rare circumstances, it's possible a descriptor writeback will occur
before a timestamped Tx packet will go out on the wire, leading to the
driver believing the hardware failed to timestamp the packet. Schedule a
work item for 82576 and use the available time sync interrupt registers
on 82580 and above to account for this.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change the name of the adapter in the PTP struct to enable easier
correlation between interface and PTP device.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update ethtool_get_ts_info to not report any supported functionality on
82575 and add support for V2 Sync and V2 Delay packets. In the case
where CONFIG_IGB_PTP is not defined, we should be reporting default
values.
v2: Correct the function to return EOPNOTSUPP when there is no PTP support
or the device does not support PTP. Also fix minor whitespace issue.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Where possible, move PTP-related functions into igb_ptp.c and update the
names of functions and variables to match the established coding style
in the files and specify that they are PTP-specific.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For users without CONFIG_IGB_PTP=y, we should not be compiling any PTP
code into the driver. Tidy up the wrapping in igb to support this.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Merge Gavin patches from the PCI tree as subsequent powerpc
patches are going to depend on them
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
John W. Linville says:
====================
This is another batch of updates intended for the 3.7 stream.
There are not a lot of large items, but iwlwifi, mwifiex, rt2x00,
ath9k, and brcmfmac all get some attention. Wei Yongjun also provides
a series of small maintenance fixes.
This also includes a pull of the wireless tree in order to satisfy
some prerequisites for later patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This part of the tty tree (unfortunately with all the preceding patches
as well) is a dependency for some of the OMAP cleanups, so we've pulled
it in as a dependency based on agreement with Greg.
Signed-off-by: Olof Johansson <olof@lixom.net>
Noticed that the byte and packet count statistics are under-
counting traffic handled by the DDP offload when there is more
than one DDP completion processed in a single call to
ixgbe_clean_rx_irq. This patch fixes that.
I tried to optimize the setting of the rss value so that it
only would have to be computed once, and only when there is
a DDP completion present.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Added the reg_ops file to debugfs with commands to read and write
a register to give users the ability to read and write individual
registers on the fly.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Added the netdev_ops file to debugfs with a command to call the
ndo_tx_timeout function to give users the ability to simulate a
tx_timeout call made by the kernel.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds debugfs support to the ixgbe driver to give
users the ability to access kernel information and to
simulate kernel events.
The filesystem is set up in the following driver/PCI-instance
hierarchy:
<debugfs>
|-- ixgbe
|-- PCI instance
| |-- attribute files
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use %u instead of %d to display u32 variable.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Robert Garrett <RobertX.Garrett@intel.com>
Tested-by: Robert Garrett <RobertX.Garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change fixes the assumptions of the rate limiting code that previously
assumed that each VF would only ever have 2 queues. This update makes it
so that we now use a queues per pool value that is determined based on the
VMDq feature mask.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-By: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Robert Garrett <RobertX.Garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The PF was not correctly registering any of its VLANs. As a result any
VLAN tagged traffic from the VF would not be delivered to the PF because
the VLAN was never assigned to the PF pool.
In addition the VF was not allowed to receive traffic from VLAN 0 if it was
allowed to receive untagged frames. This change corrects that so that it
will correctly receive traffic from VLAN 0.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Otto Estuardo Solares Cabrera <solca@galileo.edu>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
net/netfilter/nfnetlink_log.c
net/netfilter/xt_LOG.c
Rather easy conflict resolution, the 'net' tree had bug fixes to make
sure we checked if a socket is a time-wait one or not and elide the
logging code if so.
Whereas on the 'net-next' side we are calculating the UID and GID from
the creds using different interfaces due to the user namespace changes
from Eric Biederman.
Signed-off-by: David S. Miller <davem@davemloft.net>
The only user of sock_update_classid() is net/socket.c which happens
to include cls_cgroup.h directly.
tj: Fix build breakage due to missing cls_cgroup.h inclusion in
drivers/net/tun.c reported in linux-next by Stephen.
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Gao feng <gaofeng@cn.fujitsu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: netdev@vger.kernel.org
Cc: cgroups@vger.kernel.org
In order to remove dependency on mach/irqs.h, add platform device
resources for irqs.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Samuel Ortiz <samuel@sortiz.org>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: netdev@vger.kernel.org
Acked-by: David S. Miller <davem@davemloft.net>
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the pxa include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Paul Parsons <lost.distance@yahoo.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Acked-By: Stefan Schmidt <stefan@openezx.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Daniel Ribeiro <drwyrm@gmail.com>
Cc: Harald Welte <laforge@openezx.org>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Tomas Cech <sleep_walker@suse.cz>
Cc: Sergey Lapin <slapin@ossfans.org>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Dan Williams <djbw@fb.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: openezx-devel@lists.openezx.org
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the netx include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
This patch adds on the fixes done in commits 89dd86db78 ("mlx4_core:
Allow large mlx4_buddy bitmaps") and 3de819e6b6 ("mlx4_core: Fix
integer overflow issues around MTT table") so that memory registration
of up to 8TB (log_num_mtt=31) finally works.
It fixes integer overflows in a few mlx4_table_yyy routines in icm.c
by using a u64 intermediate variable, and int/uint issues that caused
table indexes to become nagive by setting some variables to be u32
instead of int. These problems cause crashes when a user attempted to
register > 512GB of RAM.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
* commit 'v3.6-rc5': (1098 commits)
Linux 3.6-rc5
HID: tpkbd: work even if the new Lenovo Keyboard driver is not configured
Remove user-triggerable BUG from mpol_to_str
xen/pciback: Fix proper FLR steps.
uml: fix compile error in deliver_alarm()
dj: memory scribble in logi_dj
Fix order of arguments to compat_put_time[spec|val]
xen: Use correct masking in xen_swiotlb_alloc_coherent.
xen: fix logical error in tlb flushing
xen/p2m: Fix one-off error in checking the P2M tree directory.
powerpc: Don't use __put_user() in patch_instruction
powerpc: Make sure IPI handlers see data written by IPI senders
powerpc: Restore correct DSCR in context switch
powerpc: Fix DSCR inheritance in copy_thread()
powerpc: Keep thread.dscr and thread.dscr_inherit in sync
powerpc: Update DSCR on all CPUs when writing sysfs dscr_default
powerpc/powernv: Always go into nap mode when CPU is offline
powerpc: Give hypervisor decrementer interrupts their own handler
powerpc/vphn: Fix arch_update_cpu_topology() return value
ARM: gemini: fix the gemini build
...
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
drivers/rapidio/devices/tsi721.c
Commit a334872224 added afex support but lacked
several logical changes. This lack can cause afex to crash, and also
have a slight effect on other flows (i.e., driver always assumes the Tx ring
has less available buffers than what it actually has).
This patch adds the missing segments, fixing said issues.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under traffic, there are several registers that when read (e.g., via
'ethtool -d') may cause the chip to stall.
This patch corrects the registers read in such flows.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch propagates users' requested flow-control into the link layer,
which will later be used to advertise this flow-control for auto-negotiation
(until now these values were ignored).
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to this fix, the driver reported the chip's active duplex state
is always 'full', even if using half-duplex mode.
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent updating the xmac PFC configuration when using a link speed
slower than 10G -the umac block is responsible for 1G or slower connections,
therefore it is possible the xmac block is reset when connection is slower.
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW needs the driver statistics for management. Current logic is broken
in that the function that gathers the port statistics does not copy
its own statistics to a place where the FW can use it.
This patch causes every function that can pass statistics to the FW to
do so.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During traffic when DCB is enabled, it is possible for multiple instances
of statistics queries to be sent to the chip - this may cause the FW to assert.
This patch prevents the sending of an additional instance of statistics query
while the previous query hasn't completed.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a hang on suspend due to calling wdm_suspend on
the unregistered data interface. The hang should have been
a NULL pointer reference had it not been for a logic error
in the cdc_wdm code.
commit 230718bd net: qmi_wwan: bind to both control and data interface
changed qmi_wwan to use cdc_wdm as a subdriver for devices with
a two-interface QMI/wwan function. The commit failed to update
qmi_wwan_suspend and qmi_wwan_resume, which were written to handle
either a single combined interface function, or no subdriver at all.
The result was that we called into the subdriver both when the
control interface was suspended and when the data interface was
suspended. Calling the subdriver suspend function with an
unregistered interface is not supported and will make the
subdriver bug out.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change various flows in the bnx2x driver which up until now flapped
the link - these flows now benefit from the link flap avoidance mechanism.
This includes the removal of the link reset made upon nic init, as it is
possible the link is already active at that time.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Various flows in the bnx2x driver cause a link-flap - if the link
is up, it would be toggled down (after a mac/phy reset) and then
taken back up.
In many of these cases, there is no need to do cause such a flap,
as the associated flows should not actually affect the link.
This patch adds the 'Link Flap Avoidance' mechanism, which allows
the driver to better determine if a given flow requires a link change,
and thus minimize the number of link flaps caused by the driver.
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate the interrupt setting part of each external PHY to a specific
function.
This allows calling the interrupt setting in case of link-flap avoidance,
since some link owners may not enable the interrupt on their own.
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* commit 'v3.6-rc5': (1098 commits)
Linux 3.6-rc5
HID: tpkbd: work even if the new Lenovo Keyboard driver is not configured
Remove user-triggerable BUG from mpol_to_str
xen/pciback: Fix proper FLR steps.
uml: fix compile error in deliver_alarm()
dj: memory scribble in logi_dj
Fix order of arguments to compat_put_time[spec|val]
xen: Use correct masking in xen_swiotlb_alloc_coherent.
xen: fix logical error in tlb flushing
xen/p2m: Fix one-off error in checking the P2M tree directory.
powerpc: Don't use __put_user() in patch_instruction
powerpc: Make sure IPI handlers see data written by IPI senders
powerpc: Restore correct DSCR in context switch
powerpc: Fix DSCR inheritance in copy_thread()
powerpc: Keep thread.dscr and thread.dscr_inherit in sync
powerpc: Update DSCR on all CPUs when writing sysfs dscr_default
powerpc/powernv: Always go into nap mode when CPU is offline
powerpc: Give hypervisor decrementer interrupts their own handler
powerpc/vphn: Fix arch_update_cpu_topology() return value
ARM: gemini: fix the gemini build
...
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
drivers/rapidio/devices/tsi721.c
From "Uwe Kleine-Knig" <u.kleine-koenig@pengutronix.de>:
this is the 2nd version of this series whose goal is to make struct
of_device_id.data const. Conceptually a driver must not modify the data
contained there so making it const is the right thing.
v1 of this series was sent with Message-id:
1342182734-321-1-git-send-email-y. Changes since then are:
- powerpc fixes
- several new consts that were found by Arnd that are possible after
patch 19.
Arnd suggested to take this series via arm-soc late for 3.6 in one go
because patch 19 depends on the former patches but is a precondition to
the latter and it fixes a few warnings. So getting it in via the
respective maintainer trees would need a much bigger coordination
effort. That means I prefer getting Acks over you taking the patch.
Vinod Koul already took
dmaengine: at_hdmac: add a few const qualifiers
that is in next-20120723 as 7fd63ccdad now. Vinod, I don't follow your
pull requests, but assuming you didn't let it already pull for 3.6 I
suggest you drop it from your queue and I just take your Ack.
This series was build tested for arm (all defconfigs) and powerpc (all
defconfigs and an allyesconfig) and grep didn't find more issues. As
before it introduces a warning in drivers/regulator/twl-regulator.c.
This driver does modify its .of_match_table when a device is bound which
doesn't fits the concept of independant devices. Arnd noticed another
new warning in drivers/scsi/qlogicpti.c that isn't that easy to resolve,
because the pointer to (now) const data is passed as first argument to
scsi_host_alloc. To fix that properly struct Scsi_Host.hostt needs to
get a const, too. Alternatively I could introduce a cast removing the
const, but I don't like that.
* 'ofdeviceiddata' of git://git.pengutronix.de/git/ukl/linux: (25 commits)
dma: tegra: make data used as *of_device_id.data const
can: mpc5xxx_can: make data used as *of_device_id.data const
macintosh/mediabay: make data used as *of_device_id.data const
i2c/mpc: make data used as *of_device_id.data const
mfd/da9052: make i2c_device_id array const
powerpc/fsl_msi: drop unneeded cast to non-const pointer
gpio/gpio-omap: make platformdata used as *of_device_id.data const
of: add const to struct *of_device_id.data
dma: tegra: make tegra_dma.chip_data a pointer to const data
watchdog/mpc8xxx: add a const qualifier
powerpc/celleb_pci: add a const qualifier
powerpc/fsl_msi: add a const qualifier
powerpc/83xx: add a const qualifier
macintosh/mediabay: add a const qualifier
mmc/omap_hsmmc: add a const qualifier
i2c/mpc: add a const qualifier
i2c/i2c-omap: add a const qualifier
gpio/mpc8xxx: add a const qualifier
gpio/gpio-omap.c: add a const qualifier
misc/atmel_tc: make atmel_tc.tcb_config member point to const data
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: repulled a v3 version of the branch that rebased to add some more
acked-bys and added one more patch on top for tegra]
Signed-off-by: Olof Johansson <olof@lixom.net>
* pci/stephen-const:
make drivers with pci error handlers const
scsi: make pci error handlers const
netdev: make pci_error_handlers const
PCI: Make pci_error_handlers const
All of the rtlwifi-family of drivers have been in the kernel since 3.1
or earlier. The dependence on EXPERIMENTAL can be removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds e-scan support (currently i-scan is in use). E-scan
is a more powerful and memory efficient method for scanning. E-scan
will be the default scan method and eventually, i-scan support will
be removed. The scan methods do not make any difference to the end-user.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes usage of some of the local data in the usb
host interface driver. This is a step in the preperation to
support multiple USB devices.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug where rx buffer does not get refilled if the
packet received has an rx protocol error.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clean up scan related code in preparation of a new scan mechanism (e-scan)
which will follow in a separate patch.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable tx flow control for USB host interface.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware events can contain extra data. This patch adds support to
copy this data when it exists.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When tx flow is to be blocked due to host interface throttle then
all net if queues should be stopped.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ssid len is 32 bit and needs endian conversion for big endian systems.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are a number of problems that occur for the latest version
of the Realtek RTL8188CE device with the in-kernel driver. These
include selection of the wrong firmware, and system lockup. A full
fix is known, but is too invasive for inclusion in stable. This patch
fixes the problem with loading the wrong firmware, and logs a message
that the device may not work for kernels 3.6 and older.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Cc: Anisse Astier <anisse@astier.eu>
Cc: Li Chaoming <chaoming_li@realsil.com.cn>
Tested-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CMD_MAC_CONTROL is currently sent async to the firmware, and is sent
from the lbs_setup_firmware() path during device init.
This means that device init can complete with commands pending, and
the if_sdio driver will sometimes power down the device (after init)
with this command still pending.
This was causing an occasional spurious command timeout after init,
leading to a device reset.
Fix this by making CMD_MAC_CONTROL synchronous when called from the
lbs_setup_firmware() path.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The register macros for antenna diversity are common for
AR9462 and AR9565, rename them.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds separate tx packet descriptor routine for AP
interface. This function fills bss_type, bss_num, wmm packet
delay information etc for TxPD going on AP interface.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some platforms do not support WOW. Let's change the default wakeup
criteria to 0.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We will use world regulatory domain (country 00) as default
when driver is loaded. Later after a successful association
cfg80211 will change the regulatory domain to a specific country
if the AP has advertised country IE.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AP's country ie is parsed and 11d information is updated in firmware
while associating. Previous mwifiex_send_domain_info_cmd_fw() call in
association path is not necessary now. Hence it is removed in this
patch.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"adapter->bss_prio_tbl[j].bss_prio_head" points to linked list of
interfaces with priority 'j'. "bss_prio_tbl[j].bss_prio_cur" is
supposed to point to next interface every time the routine for
dequeuing the packet is called. This ensures that each interface
gets fair chance.
Currently we have AP and station interfaces with priority '0'.
Therefore "adapter->bss_prio_tbl[0].bss_prio_cur" should
alternately point to AP and station nodes. Since "bss_prio_cur"
is not correctly updated, for each packet picked for AP, two
packets are picked for station interface.
This patch fixes the problem by correctly updating "bss_prio_cur".
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently AP interface has higher priority over station. Hence
separate entries are created in "adapter->bss_prio_tbl" for these
interfaces and station packet is dequeued only if there is not
packet in queue for AP. It is observed that ping for station
interface doesn't work if heavy traffic is running on AP.
The problem is fixed by having same priority for both the
interfaces. This patch also removes an extra initialisation
for "priv->bss_priority".
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
HostCmd_CMD_AMSDU_AGGR_CTRL is never called with GET action.
So the code in mwifiex_ret_amsdu_aggr_ctrl() becomes redundant.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
HostCmd_CMD_11N_CFG is never called with GET action. So the code in
mwifiex_ret_11n_cfg() becomes redundant.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't send this command with GET action. Redundant code in
mwifiex_ret_subsc_evt() is removed in this patch.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever BT calibration requested, WLAN has to wait for the
calibration to be completed. But right now we defer the waiting
which might cause BT calibration to fail. Fix that.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In rndis_scan(), 'request' is actually always valid pointer and
the !request check is unneeded, so remove it.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Various parts of the code require AR9565 checks,
this patch adds them.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
And recognize the device in the init path.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a regression which was introduced in:
"mac80211: move TX station pointer and restructure TX"
IP: p54_tx_80211+0x21/0x513 [p54common]
Oops: 0000 [#1] SMP
Modules linked in: p54usb p54common [...]
Pid: 13394, comm: hostapd 3.6.0-rc4-wl+
RIP: 0010:p54_tx_80211+0x21/0x513
RSP: 0018:... EFLAGS: 00010292
[...]
Process hostapd
Stack:
[...]
Call Trace:
p54_bss_info_changed+0x204/0x21e [p54common]
ieee80211_del_station+0x16/0x32 [mac80211]
ieee80211_start_ap+0x10f/0x157 [mac80211]
nl80211_start_ap+0x315/0x361 [cfg80211]
p54_tx_80211 function is called as part of the
beacon update. The caller p54_bss_info_changed
has to supply a valid tx control struct, or
the control->sta will lead to a null pointer
dereference.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
removes unnecessary semicolon
Found by Coccinelle: http://coccinelle.lip6.fr/
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Having generic hardware timer interrupt in debugfs
would come handy when we are debugging 3 WIRE
BTCOEX issues.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Read and configure thermometer calibration results read from
OTP card.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
removes unnecessary semicolon
Found by Coccinelle: http://coccinelle.lip6.fr/
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hex2str() is substituted by '%*phD' specificator.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before disabling BTCOEX in the h/w cancel all BTCOEX related
works. This is similar to the commit in ath9k(c32cdbd8)
ath9k: Stop the BTCOEX timers before disabling BTCOEX
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable BTCOEX for WB193(which seems to be the only supported
ath9k_htc BTCOEX chipset)only when it is enabled via modparam,
rather than enabling it by default.
Cc: Vivek Natarajan <nataraja@qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
*Remove all the checks that will be handled by cfg80211
based on the interface combination advertised. For instance,
driver supports at the maximum 8 beaconing interface, while
we advertise maximum 8 beaconing interface in the interface
combination support.
*cfg80211 will take care of not allowing
us to add an interface that is not supported by the
driver, further if the change_interface changes the
old interface to a beaconing interface while we had
reached the max limit of 8 beaconing interface, again
cfg80211 takes care of this stuff!
So remove all these checks.
*Beautify placing PS wrappers in the appropriate
position.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Additionally it has a neat debug message informing us
that we are stopping the ANI algorithm.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Its more correct to convert btcoex_period to 'us' while
comparing with btcoex_no_stomp which is in 'us'.
Did not find any functionality issues being fixed,
as the generic hardware timer triggers are usually
refreshed with the newer duty cycle.
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a possibility that AR_MCI_GPM_1 register can
return 0xdeadbeef and this results in caching of invalid
GPM index in ar9003_mci_is_gpm_valid. Ensure we
have appropriate checks to avoid this.
Cc: xijin luo <xijin@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
gcc 4.8 warns for this memcpy. While the copy size is correct, the whole
copy seems to be a nop because the destination is never used, and
there's no need to use memcpy to copy pointers anyways. And the
type of the pointer was wrong, but at least those are always the same.
Just remove it.
/backup/lsrc/git/linux-lto-2.6/drivers/net/wireless/brcm80211/brcmsmac/aiutils.c: In function 'ai_detach':
/backup/lsrc/git/linux-lto-2.6/drivers/net/wireless/brcm80211/brcmsmac/aiutils.c:539:32: warning: argument to 'sizeof' in 'memcpy' call is the same pointer type 'struct si_pub **' as the destination; expected 'struct si_pub *' or an explicit length [-Wsizeof-pointer-memaccess]
memcpy(&si_local, &sih, sizeof(struct si_pub **));
^
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
zd1211rw lacks hardware encryption, so enabling 802.11w is only matter of
enabling IEEE80211_HW_MFP_CAPABLE flag.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Support for the RT3352 WiSoC was developed for and tested with the ALL5002
devboard running OpenWrt. For now, this supports only devices with internal
TXALC. Corrections were made according to the remarks of Stanislaw Gruszka and
Gertjan van Wingerde, thank you guys for reviewing!
Signed-off-by: Daniel Golle <dgolle@allnet.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since of_device_id.data is declared as a pointer to const data a few
more consts can be added in this driver.
[ukl: split Arnd's patch by driver]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
HP un2430 is a Gobi 3000 device. It was mistakenly treated as Gobi 1000
in patch b9f90eb274.
I own this device and qmi_wwan works again with this fix.
Signed-off-by: Pierre Sauter <pierre.sauter@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables boards with 54618SE phys and a sufficiently new
firmware to use native EEE instead of auto-greeen.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to lay the foundation for 1G EEE support, several segments of code
which are common to both 1G and 10G EEE configurations were extracted from
the 10G EEE configuration flow to their own functions.
E.g., bnx2x_eee_initial_config, bnx2x_eee_advertise, bnx2x_eee_disable, etc.
The rest of the EEE functions were relocated and placed in a single,
continuous section of the file.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent functions from disabling EEE to other functions using other ports.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch aligns the EEE status with that of all other link properties,
by changing the way its accessed - instead of a direct read to the shared
memory, each function maintain its own copy locally.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 36a1211970 (netprio_cgroup.h:
dont include module.h from other includes) made the following build
error on ixp4xx_hss pop up:
CC [M] drivers/net/wan/ixp4xx_hss.o
drivers/net/wan/ixp4xx_hss.c:1412:20: error: expected ';', ',' or ')'
before string constant
drivers/net/wan/ixp4xx_hss.c:1413:25: error: expected ';', ',' or ')'
before string constant
drivers/net/wan/ixp4xx_hss.c:1414:21: error: expected ';', ',' or ')'
before string constant
drivers/net/wan/ixp4xx_hss.c:1415:19: error: expected ';', ',' or ')'
before string constant
make[8]: *** [drivers/net/wan/ixp4xx_hss.o] Error 1
This was previously hidden because ixp4xx_hss includes linux/hdlc.h which
includes linux/netdevice.h which includes linux/netprio_cgroup.h which
used to include linux/module.h. The real issue was actually present since
the initial commit that added this driver since it uses macros from
linux/module.h without including this file.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update version to 2.5.13.
Reviewed-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To save memory and to exit IRQ loop quicker on devices that don't support
FCoE.
Reviewed-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will make it easier to exit IRQ loop and re-arm IRQ on devices that
don't support FCoE.
Reviewed-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will free up unneeded memory.
Reviewed-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions are needed to free up memory when the rings are no longer
needed.
Reviewed-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a frequent mistake to confuse the netlink port identifier with a
process identifier. Try to reduce this confusion by renaming fields
that hold port identifiers portid instead of pid.
I have carefully avoided changing the structures exported to
userspace to avoid changing the userspace API.
I have successfully built an allyesconfig kernel with this change.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I discovered I couldn't get sierra_net to work on a powerpc. Turns out
the firmware attribute check assumes the system is little endian and
hence fails because the attributes is a 16 bit value.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for oobirq_entry allocation failure to avoid
NULL pointer dereferencing.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some checks for PA linearization support checked ATH9K_HW_CAP_PAPRD and some
used the EEPROM ops, leading to issues in tx power handling, since those
two can be out of sync.
Disable the feature by default, since it has been reported that it can
cause damage to the rx path under some circumstances. It can now be enabled
for testing via debugfs.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver provides the cfg80211 regulatory framework with a set of
custom rules. However, there was a mismatch in number of rules
and the actual rules provided. This resulted in setting an invalid
power level:
ieee80211 phy0: brcms_ops_config: change channel 13
ieee80211 phy0: brcms_ops_config: Error setting power_level (8758364)
Closer look in cfg80211 regulatory blurb showed following bogus rule:
cfg80211: 0 KHz - -60446948 KHz @ 875836468 KHz), (875836468 mBi, 875836468 mBm)
Cc: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of allocating one big chunk of DMA-coherent
memory for the firmware and keeping it around, only
vmalloc() the firmware and copy it into a single
page of DMA-coherent memory for the upload.
The advantage is that we don't need DMA memory for
the firmware image that is stored while the driver
is operating, we only need it while uploading.
This will make it easier for the driver to work if
the system has fragmented memory.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we kill the radio with the RF kill button we could access
the HW after having stopped the APM which would result in the
warning below.
The flow goes like this:
* RF kill
iwlwifi notifies the stack which stops the driver
fw sends CARD_STATE_NOTIFICATION
* iwl_trans_pcie_stop_device stops the APM
* the tasklet runs and calls to iwl_rx_handle
* iwl_rx_handle calls iwl_rx_queue_restock
* iwl_rx_queue_restock tries to access the HW...
[255908.543823] ------------[ cut here ]------------
[255908.543843] WARNING: at drivers/net/wireless/iwlwifi/iwl-io.c:150 iwl_grab_nic_access+0x79/0xb0 [iwlwifi]()
[255908.543849] Hardware name: Latitude E6410
[255908.543852] Timeout waiting for hardware access (CSR_GP_CNTRL 0x000003d8)
[255908.543856] Modules linked in: iwlmvm iwlwifi mac80211 [...]
[255908.543935] Pid: 0, comm: swapper Tainted: G W 3.1.0 #1
[255908.543939] Call Trace:
[255908.543950] [<c1046e42>] warn_slowpath_common+0x72/0xa0
[255908.543980] [<c1046f13>] warn_slowpath_fmt+0x33/0x40
[255908.543992] [<fa4bb3b9>] iwl_grab_nic_access+0x79/0xb0 [iwlwifi]
[255908.544004] [<fa4bb9eb>] iwl_write_direct32+0x2b/0xa0 [iwlwifi]
[255908.544018] [<fa4c0ff9>] iwl_rx_queue_update_write_ptr+0x89/0x1d0 [iwlwifi]
[255908.544054] [<fa4c1250>] iwlagn_rx_queue_restock+0x110/0x140 [iwlwifi]
[255908.544067] [<fa4c234d>] iwl_irq_tasklet+0x82d/0xf40 [iwlwifi]
[255908.544096] [<c104e11e>] tasklet_action+0xbe/0x100
[255908.544102] [<c104d91e>] __do_softirq+0xae/0x1f0
[255908.544227] ---[ end trace d150f49345d85009 ]---
Prevent this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove outdated iwlagn prefix to a few functions and fix comments
that were not accurate.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's a block of code that's indented too
far, move it out to where it should be.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If an RX interrupt is signalled after or during apm_stop
we may try to access the peripherals which are already
down. Prevent this by disabling interrupts first.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwl_disable_interupts() already resets the register, no
need to do it again.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Mark keys that might be used to receive management
frames so drivers can fall back on software crypto
for them if they don't support hardware offload.
As the new flag is only set correctly for RX keys
and the existing IEEE80211_KEY_FLAG_SW_MGMT flag
can only affect TX, also rename the latter to
IEEE80211_KEY_FLAG_SW_MGMT_TX.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mdio-mux-mmioreg.c uses function of_address_to_resource(), which is defined
in linux/of_address.h. This fixes a compilation error:
drivers/net/phy/mdio-mux-mmioreg.c: In function 'mdio_mux_mmioreg_probe':
drivers/net/phy/mdio-mux-mmioreg.c:83:2: error: implicit declaration of
function 'of_address_to_resource'
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For NIC/System time synchonisation efx_mcdi_rpc needs to be split in
efx_mcdi_rpc_start and efx_mcdi_rpc_finish operations.
Signed-off-by: Stuart Hodgson <smhodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Allows an extra channel to override the standard receive_skb handler
and also for extra non generic operations to be performed on remove.
Also set default rx strategy so only skbs can be delivered to the
PTP receive function.
Signed-off-by: Stuart Hodgson <smhodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The PTP channel will have its own RX queue even though it's not
a regular traffic channel.
Original work by Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Stuart Hodgson <smhodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Refactor the probe_hw code so that more code can be shared between
rt2800pci and rt2800usb.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The various rt2x00 drivers use different methods to name the different
GPIO register fields indicating the GPIO pin value and the fields
indicating the direction.
Start using a unified naming scheme for the GPIO register fields:
- <csr>_VAL<x> for fields indicating the GPIO pin value.
- <csr>_DIR<x> for fields indicating the GPIO pin direction.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo Van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ensure that all active GPIO pins are included in the GPIO register
definitions, nothing more and nothing less.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo Van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The latest version of the vendor driver for the rtlwifi family
includes many changes. This patch incorporates the difference
in the main header file.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rtlwifi family of drivers has the following sparse errors:
CHECK drivers/net/wireless/rtlwifi/usb.c
drivers/net/wireless/rtlwifi/usb.c:122:17: warning: cast to restricted __le32
CHECK drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c
drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c:1157:13: warning: context imbalance in 'rtl92c_dm_refresh_rate_adaptive_mask' - different lock contexts for basic block
CHECK drivers/net/wireless/rtlwifi/rtl8192ce/hw.c
drivers/net/wireless/rtlwifi/rtl8192ce/hw.c:1909:30: warning: cast to restricted __le32
CHECK drivers/net/wireless/rtlwifi/rtl8192ce/sw.c
drivers/net/wireless/rtlwifi/rtl8192ce/sw.c:345:1: warning: symbol 'rtl92ce_pci_ids' was not declared. Should it be static?
CHECK drivers/net/wireless/rtlwifi/rtl8192cu/trx.c
drivers/net/wireless/rtlwifi/rtl8192cu/trx.c:494:9: warning: cast from restricted __le16
CHECK drivers/net/wireless/rtlwifi/rtl8192se/fw.c
drivers/net/wireless/rtlwifi/rtl8192se/fw.c:490:17: warning: cast to restricted __le32
drivers/net/wireless/rtlwifi/rtl8192se/fw.c:490:17: warning: cast to restricted __le32
drivers/net/wireless/rtlwifi/rtl8192se/fw.c:494:17: warning: cast to restricted __le32
drivers/net/wireless/rtlwifi/rtl8192se/fw.c:494:17: warning: cast to restricted __le32
drivers/net/wireless/rtlwifi/rtl8192se/fw.c:499:17: warning: cast to restricted __le32
drivers/net/wireless/rtlwifi/rtl8192se/fw.c:499:17: warning: cast to restricted __le32
drivers/net/wireless/rtlwifi/rtl8192se/fw.c:510:25: warning: cast to restricted __le32
drivers/net/wireless/rtlwifi/rtl8192se/fw.c:510:25: warning: cast to restricted __le32
drivers/net/wireless/rtlwifi/rtl8192se/fw.c:607:9: warning: cast to restricted __le16
drivers/net/wireless/rtlwifi/rtl8192se/fw.c:607:9: warning: cast to restricted __le16
drivers/net/wireless/rtlwifi/rtl8192se/fw.c:650:9: warning: cast to restricted __le16
drivers/net/wireless/rtlwifi/rtl8192se/fw.c:650:9: warning: cast to restricted __le16
drivers/net/wireless/rtlwifi/rtl8192se/fw.c:652:9: warning: cast to restricted __le16
drivers/net/wireless/rtlwifi/rtl8192se/fw.c:652:9: warning: cast to restricted __le16
CHECK drivers/net/wireless/rtlwifi/rtl8192se/trx.c
drivers/net/wireless/rtlwifi/rtl8192se/trx.c:758:9: warning: cast from restricted __le32
drivers/net/wireless/rtlwifi/rtl8192se/trx.c:788:17: warning: cast from restricted __le32
drivers/net/wireless/rtlwifi/rtl8192se/trx.c:804:17: warning: cast to restricted __le32
drivers/net/wireless/rtlwifi/rtl8192se/trx.c:804:17: warning: cast to restricted __le32
drivers/net/wireless/rtlwifi/rtl8192se/trx.c:807:17: warning: cast from restricted __le32
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
