This patch fixes a lockdep warning in igb_get_i2c_client by
refactoring the initialization and usage of the i2c_client
completely. There is no on the fly allocation of the single
client needed today.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes the setup copper link function to use a switch
statement for the PHY id's available for the given PHY types. It
also adds a case for the I210 PHY id, so the appropriate setup link
function is called for it.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On s390 the igb driver was throwing a build error due to the fact that a frame
built using build_skb would be larger than 2K. Since this is not likely to
change at any point in the future we are better off just dropping the check
since we already had a check in igb_set_rx_buffer_len that will just disable
the usage of build_skb anyway.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
At 1000Mbps link speed, one of the MAC's internal clocks can be stopped for
up to 4us when entering K1 (a power mode of the MAC-PHY interconnect). If
the MAC is waiting for completion indications for 2 DMA write requests into
Host memory (e.g. descriptor writeback or Rx packet writing) and the
indications occur while the clock is stopped, both indications will be
missed by the MAC causing the MAC to wait for the completion indications
and be unable to generate further DMA write requests. This results in an
apparent hardware hang.
Work-around the issue by disabling the de-assertion of the clock request
when 1000Mbps link is acquired (K1 must be disabled while doing this).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
build error cause by
Commit ff43da86c6
("NET: FEC: dynamtic check DMA desc buff type")
drivers/net/ethernet/freescale/fec.c: In function ‘fec_enet_get_nextdesc’:
drivers/net/ethernet/freescale/fec.c:215:18: error: invalid use of undefined type ‘struct bufdesc_ex’
drivers/net/ethernet/freescale/fec.c: In function ‘fec_enet_get_prevdesc’:
drivers/net/ethernet/freescale/fec.c:224:18: error: invalid use of undefined type ‘struct bufdesc_ex’
drivers/net/ethernet/freescale/fec.c: In function ‘fec_enet_start_xmit’:
drivers/net/ethernet/freescale/fec.c:286:37: error: arithmetic on pointer to an incomplete type
drivers/net/ethernet/freescale/fec.c:287:13: error: arithmetic on pointer to an incomplete type
drivers/net/ethernet/freescale/fec.c:324:7: error: dereferencing pointer to incomplete type etc....
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a resubmission.
Added kfree() in ax88179_get_eeprom to prevent memory leakage.
Modified "__le16 rxctl" to "u16 rxctl" in "struct ax88179_data" and removed pointless casts.
Removed asix_init and asix_exit functions and added "module_usb_driver(ax88179_178a_driver)".
Fixed endianness issue on big endian systems and verified this driver on iBook G4.
Removed steps that change net->features in ax88179_set_features function.
Added "const" to ethtool_ops structure and fixed the coding style of AX88179_BULKIN_SIZE array.
Fixed the issue that the default MTU is not 1500.
Added ax88179_change_mtu function and enabled the hardware jumbo frame function to support an
MTU higher than 1500.
Fixed indentation and empty line coding style errors.
The _nopm version usb functions were added to access register in suspend and resume functions.
Serveral variables allocted dynamically were removed and replaced by stack variables.
ax88179_get_eeprom were modified from asix_get_eeprom in asix_common.
This patch adds a driver for ASIX's AX88179 family of USB 3.0/2.0
to gigabit ethernet adapters. It's based on the AX88xxx driver but
the usb commands used to access registers for AX88179 are completely different.
This driver had been verified on x86 system with AX88179/AX88178A and
Sitcomm LN-032 USB dongles.
Signed-off-by: Freddy Xin <freddy@asix.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phyter KSZ9021 has hardware bug. If asymmetric pause is enabled,
then it is necessary to disconnect and then reconnect the ethernet
cable to get the phyter working. The solution is to disable the
asymmetric pause.
Signed-off-by: Vlastimil Kosar <ikosar@fit.vutbr.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not include the frame check sequence when adding the skb to
netif_receive_skb(). This causes problems when this interface was
bridged to a wifi ap and a big package should be forwarded from this
Ethernet driver through a bride to the wifi client.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix memory leak in phy_device_free() for the case when phy_device*
returned by phy_device_create() is not registered in the system.
Bug description:
phy_device_create() sets name of kobject using dev_set_name(), which
allocates memory using kvasprintf(), but this memory isn't freed if
the underlying device isn't registered properly, because kobject_cleanup()
is not called in that case. This can happen (and actually is happening on
our machines) if phy_device_register(), called by mdiobus_scan(), fails.
Patch description:
Embedded struct device is initialized in phy_device_create() and it
counterpart phy_device_free() just drops one reference to the device,
which leads to proper deinitialization including releasing the kobject
name memory.
Signed-off-by: Petr Malat <oss@malat.biz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix condition typo for running KR2 work-around though it doesn't have
real effect since the typo bits matched by chance.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix KR2 link down problem after reboot when link speed is reconfigured via ethtool.
Since 1G/10G support link speed were missing by default, 1G/10G link speed were
not advertised.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the "ethtool -p" for boards with BCM84834, by using LED4 of the PHY
to toggle the link LED while keeping interrupt disabled to avoid NIG attentions,
and at the end restore NIG to previous state.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some hardware start settings implicitely assume an usual 1500 bytes mtu
that can't be guaranteed because changes of mtu may be requested both
before and after the hardware is started.
Reported-by: Tomi Orava <tomimo@ncircle.nullnet.fi>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_MAC80211_MESH is not set, cfg80211 will now allow advertising
interface combinations with NL80211_IFTYPE_MESH_POINT present.
Add appropriate ifdefs to avoid running into errors.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Maximum delay for waking up card is 50 ms. Because of typo in
counter, this delay goes to 500ms. This patch fixes the bug.
Cc: <stable@vger.kernel.org> # 3.2+
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On many different chips, important aspects of the MAC state are not
fully cleared by a warm reset. This can show up as tx/rx hangs, those
annoying "DMA failed to stop in 10 ms..." messages or other quirks.
On AR933x, the chip can occasionally get stuck in a way that only a
driver unload/reload or a reboot would bring it back to life.
With this patch, a full reset is issued when bringing the chip out of
FULL-SLEEP state (after idle), or if either Rx or Tx was not shut down
properly. This makes the DMA related error messages disappear completely
in my tests on AR933x, and the chip does not get stuck anymore.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ath9k commit 2ef167557c
(ath9k: fix signal strength reporting issues) fixed an issue where the
reported per-frame signal strength reported to mac80211 was being
overwritten with an internal average. The same issue is also present
in ath9k_htc.
In addition to preventing the driver from overwriting the value, this
commit also ensures that the internal average (which is used for ANI)
only tracks beacons of the AP that we're connected to.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RSSI is being stored internally as s8 in several places. The indication
of an unset RSSI value, ATH_RSSI_DUMMY_MARKER, was supposed to have been
set to 127, but ended up being set to 0x127 because of a code cleanup
mistake. This could lead to invalid signal strength values in a few
places.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This USB ethernet adapter was purchased in anodyne packaging
from the computer store adjacent to linux.conf.au 2013 in
Canberra (Australia). A web search shows other recent
purchasers in Lancaster (UK) and Seattle (USA). Just like an
emergent virus, our age of e-commerce and airmail allows
underdocumented hardware to spread around the world instantly
using the vector of ridiculously low prices.
Paige Thompson, infected via eBay, discovered that the HG20F9
is a copy of the Asix 88772B; many viruses copy the RNA of
other viruses. See Paige's work at
<https://github.com/paigeadele/HG20F9>.
This patch uses her discovery to update the restructured Asix
driver in the current kernel.
Just as some viruses inhabit seemingly-healthy cells, the
HG20F9 uses the Vendor ID 0x066b assigned to Linksys Inc.
For the present there is no clash of Product ID 0x20f9.
Signed-off-by: Glen Turner <gdt@gdt.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tag all Huawei NCM devices as WWAN modems, as we don't know of any which
are not. This is necessary for userspace clients to know that the device
requires further setup on e.g. an AT-capable serial ports before
connectivity is available.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 86564c3f "bnx2x: Remove many sparse warnings" UDP
csum offload is broken for 57710/57711. Fix return value.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
CC: Ariel Elior <ariele@broadcom.com>
CC: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PIC was supposed to be a small signature appended to the
PhyDB data, but the signature isn't really static and thus
attempting to check it just causes the warnings spuriously
so remove them.
Signed-off-by: Dor Shaish <dor.shaish@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The wakeup packet in the status response is padded out
to a multiple of 4 bytes by the firmware for transfer
to the host, take that into account when checking the
length of the command.
Also, the reported wakeup packet includes the FCS but
the userspace API doesn't, so remove that. If it is a
data packet it is reported as an 802.3 packet but I
forgot to take into account and remove the encryption
head/tail, fix all of that as well.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
in bond_enslave(), check slave_cnt before actually using slave address.
introduced by:
commit 409cc1f8a4 (bond: have random dev address by default instead of zeroes)
Reported-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make cpsw_add_default_vlan() look at the actual number of slaves for its
iteration, so boards with less than 2 slaves don't ooops at boot.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: David S. Miller <davem@davemloft.net>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings says:
====================
Some fixes that should go into 3.9:
1. Fix packet corruption when using non-coherent RX DMA buffers.
2. Fix occasional watchdog misfiring when changing MTU or ring size.
These are longstanding bugs and should be fixed in stable as well, but
I'd like to review other recent fixes first and send a separate request
for stable inclusion.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When stations are removed while packets are in the queue,
we drain the queues first, and then remove the stations.
If this happens in AP mode while the interface is removed
the MAC context might be removed from the firmware before
we removed the station(s), resulting in a SYSASSERT 3421.
This is because we remove the MAC context from the FW in
stop_ap(), but only flush the station drain work later in
remove_interface().
Refactor the code a bit to have a common MAC context
removal preparation first to solve this.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The FH hardware will always write back to the scratch field
in commands, even host commands not just TX commands, which
can overwrite parts of the command. This is problematic if
the command is re-used (with IWL_HCMD_DFL_NOCOPY) and can
cause calibration issues.
Address this problem by always putting at least the first
16 bytes into the buffer we also use for the command header
and therefore make the DMA engine write back into this.
For commands that are smaller than 16 bytes also always map
enough memory for the DMA engine to write back to.
Cc: stable@vger.kernel.org
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull networking fixes from David Miller:
1) ping_err() ICMP error handler looks at wrong ICMP header, from Li
Wei.
2) TCP socket hash function on ipv6 is too weak, from Eric Dumazet.
3) netif_set_xps_queue() forgets to drop mutex on errors, fix from
Alexander Duyck.
4) sum_frag_mem_limit() can deadlock due to lack of BH disabling, fix
from Eric Dumazet.
5) TCP SYN data is miscalculated in tcp_send_syn_data(), because the
amount of TCP option space was not taken into account properly in
this code path. Fix from yuchung Cheng.
6) MLX4 driver allocates device queues with the wrong size, from Kleber
Sacilotto.
7) sock_diag can access past the end of the sock_diag_handlers[] array,
from Mathias Krause.
8) vlan_set_encap_proto() makes incorrect assumptions about where
skb->data points, rework the logic so that it works regardless of
where skb->data happens to be. From Jesse Gross.
9) Fix gianfar build failure with NET_POLL enabled, from Paul
Gortmaker.
10) Fix Ipv4 ID setting and checksum calculations in GRE driver, from
Pravin B Shelar.
11) bgmac driver does:
int i;
for (i = 0; ...; ...) {
...
for (i = 0; ...; ...) {
effectively corrupting the outer loop index, use a seperate
variable for the inner loops. From Rafał Miłecki.
12) Fix suspend bugs in smsc95xx driver, from Ming Lei.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (35 commits)
usbnet: smsc95xx: rename FEATURE_AUTOSUSPEND
usbnet: smsc95xx: fix broken runtime suspend
usbnet: smsc95xx: fix suspend failure
bgmac: fix indexing of 2nd level loops
b43: Fix lockdep splat on module unload
Revert "ip_gre: propogate target device GSO capability to the tunnel device"
IP_GRE: Fix GRE_CSUM case.
VXLAN: Use tunnel_ip_select_ident() for tunnel IP-Identification.
IP_GRE: Fix IP-Identification.
net/pasemi: Fix missing coding style
vmxnet3: fix ethtool ring buffer size setting
vmxnet3: make local function static
bnx2x: remove dead code and make local funcs static
gianfar: fix compile fail for NET_POLL=y due to struct packing
vlan: adjust vlan_set_encap_proto() for its callers
sock_diag: Simplify sock_diag_handlers[] handling in __sock_diag_rcv_msg
sock_diag: Fix out-of-bounds access to sock_diag_handlers[]
vxlan: remove depends on CONFIG_EXPERIMENTAL
mlx4_en: fix allocation of CPU affinity reverse-map
mlx4_en: fix allocation of device tx_cq
...
- SRP error handling fixes from Bart Van Assche
- Implementation of memory windows for mlx4 from Shani Michaeli
- Lots of cxgb4 HW driver fixes from Vipul Pandya
- Make iSER work for virtual functions, other fixes from Or Gerlitz
- Fix for bug in qib HW driver from Mike Marciniszyn
- IPoIB fixes from me, Itai Garbi, Shlomo Pongratz, Yan Burman
- Various cleanups and warning fixes from Julia Lawall, Paul Bolle, Wei Yongjun
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=RAQw
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband update from Roland Dreier:
"Main batch of InfiniBand/RDMA changes for 3.9:
- SRP error handling fixes from Bart Van Assche
- Implementation of memory windows for mlx4 from Shani Michaeli
- Lots of cxgb4 HW driver fixes from Vipul Pandya
- Make iSER work for virtual functions, other fixes from Or Gerlitz
- Fix for bug in qib HW driver from Mike Marciniszyn
- IPoIB fixes from me, Itai Garbi, Shlomo Pongratz, Yan Burman
- Various cleanups and warning fixes from Julia Lawall, Paul Bolle,
Wei Yongjun"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (41 commits)
IB/mlx4: Advertise MW support
IB/mlx4: Support memory window binding
mlx4: Implement memory windows allocation and deallocation
mlx4_core: Enable memory windows in {INIT, QUERY}_HCA
mlx4_core: Disable memory windows for virtual functions
IPoIB: Free ipoib neigh on path record failure so path rec queries are retried
IB/srp: Fail I/O requests if the transport is offline
IB/srp: Avoid endless SCSI error handling loop
IB/srp: Avoid sending a task management function needlessly
IB/srp: Track connection state properly
IB/mlx4: Remove redundant NULL check before kfree
IB/mlx4: Fix compiler warning about uninitialized 'vlan' variable
IB/mlx4: Convert is_xxx variables in build_mlx_header() to bool
IB/iser: Enable iser when FMRs are not supported
IB/iser: Avoid error prints on EAGAIN registration failures
IB/iser: Use proper define for the commands per LUN value advertised to SCSI ML
IB/uverbs: Implement memory windows support in uverbs
IB/core: Add "type 2" memory windows support
mlx4_core: Propagate MR deregistration failures to caller
mlx4_core: Rename MPT-related functions to have mpt_ prefix
...
We must only ever stop TX queues when they are full or the net device
is not 'ready' so far as the net core, and specifically the watchdog,
is concerned. Otherwise, the watchdog may fire *immediately* if no
packets have been added to the queue in the last 5 seconds.
The device is ready if all the following are true:
(a) It has a qdisc
(b) It is marked present
(c) It is running
(d) The link is reported up
(a) and (c) are normally true, and must not be changed by a driver.
(d) is under our control, but fake link changes may disturb userland.
This leaves (b). We already mark the device absent during reset
and self-test, but we need to do the same during MTU changes and ring
reallocation. We don't need to do this when the device is brought
down because then (c) is already false.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
We assume that the mapping between DMA and virtual addresses is done
on whole pages, so we can find the page offset of an RX buffer using
the lower bits of the DMA address. However, swiotlb maps in units of
2K, breaking this assumption.
Add an explicit page_offset field to struct efx_rx_buffer.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
We may currently allocate two RX DMA buffers to a page, and only unmap
the page when the second is completed. We do not sync the first RX
buffer to be completed; this can result in packet loss or corruption
if the last RX buffer completed in a NAPI poll is the first in a page
and is not DMA-coherent. (In the middle of a NAPI poll, we will
handle the following RX completion and unmap the page *before* looking
at the content of the first buffer.)
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The name of FEATURE_AUTOSUSPEND is very misleading and the actual
meaning is remote wakeup, but a device incapable of remote wakeup
still can support USB autosuspend under some situations, so rename
it to avoid misunderstanding.
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b2d4b150(smsc95xx: enable dynamic autosuspend) implements
autosuspend, but breaks current runtime suspend, such as:
when the interface becomes down, the usb device can't be put into
runtime suspend any more.
This patch fixes the broken runtime suspend.
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The three below functions:
smsc95xx_enter_suspend0()
smsc95xx_enter_suspend1()
smsc95xx_enter_suspend2()
return > 0 in case of success, so they will cause smsc95xx_suspend()
to return > 0 and cause suspend failure.
The bug is introduced in commit 3b9f7d(smsc95xx: fix error handling
in suspend failure case).
Cc: <stable@vger.kernel.org> [3.8]
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were using the same variable for iterating two nested loops.
Reported-by: Tijs Van Buggenhout <tvb@able.be>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On unload, b43 produces a lockdep warning that can be summarized in the
following way:
======================================================
[ INFO: possible circular locking dependency detected ]
3.8.0-wl+ #117 Not tainted
-------------------------------------------------------
modprobe/5557 is trying to acquire lock:
((&wl->firmware_load)){+.+.+.}, at: [<ffffffff81062160>] flush_work+0x0/0x2a0
but task is already holding lock:
(rtnl_mutex){+.+.+.}, at: [<ffffffff813bd7d2>] rtnl_lock+0x12/0x20
which lock already depends on the new lock.
[ INFO: possible circular locking dependency detected ]
======================================================
The full output is available at http://lkml.indiana.edu/hypermail/linux/kernel/1302.3/00060.html.
To summarize, commit 6b6fa58 added a 'cancel_work_sync(&wl->firmware_load)'
call in the wrong place.
The fix is to move the cancel_work_sync() call to b43_bcma_remove() and
b43_ssb_remove(). Thanks to Johannes Berg and Michael Buesch for help in
diagnosing the log output.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [V3.5+]
Signed-off-by: David S. Miller <davem@davemloft.net>
tunnel_ip_select_ident() is more efficient when generating ip-header
id given inner packet is of ipv4 type.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement MW allocation and deallocation in mlx4_core and mlx4_ib.
Pass down the enable bind flag when registering memory regions.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add memory windows-related code to INIT_HCA and QUERY_HCA.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Do not enable memory windows allocation for virtual functions.
In addition, add a few safety checks, such as:
* Verifying the PD of a new MPT matches the VF.
* Making sure binding memory window isn't enabled for FMRs, and
that new memory windows are not FMR themselves.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix missing () & { }
Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Noticed that vmxnet3's get_ringparam function was returning the summation of all
ring buffers on a NIC, rather than just the size of any one ring. This causes
problems when a vmxnet3 instance has multiple queues, as ethtool, when setting
ring parameters, first gets the current ring parameters to set the existing
values in the set_ringparm commannd. The result is, that unless both rx and tx
ring sizes are set in a single operation, which ever ring is not set will
silently have its ring count multiplied by the number of queues on the NIC until
it reaches a driver defined maxiumum value.
Fix it by not multiplying the rx and tx ring sizes by the number of queues in
the system, like every other driver. Tested by myself successfully.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Shreyas Bhatewara <sbhatewara@vmware.com>
CC: "VMware, Inc." <pv-drivers@vmware.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparse warned about several functions that were unnecessarily global.
After making them static, discovered that several functions were actually never used.
Compile tested only.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Eilon Greenstein <eilong@broadcomo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
