During a 3 stage SETUP transfer, if the host sends another SETUP token
before completing the status phase, it signifies that the host has aborted
the current control transfer. Currently, if a setup_packet_pending is
received, there are no subsequent calls to dwc3_ep0_out_start() to fetch
the new SETUP packet. This leads to a stall on EP0, as host does not
expect another STATUS phase as it has aborted the current transfer.
Fix this issue by explicitly stalling and restarting EP0, as well as
resetting the trb_enqueue indexes. (without this, there is a chance the
SETUP TRB is set up on trb_endqueue == 1)
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220712014403.2977-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit ebc4969ae1. That
commit was supposed to make the binding better reflect the MediaTek XHCI
hardware block by requiring all clocks to be present. But doing that
also causes too much noise in the devicetrees, since it requires
updating old MediaTek DTs to add clock handles for the fixed clocks, and
going forward every new clock added to the binding would require even
more updates.
The commit also didn't update the example to match the changes, causing
additional warnings.
Instead let's keep the clocks optional so that old devicetrees can keep
omitting the fixed clocks, and we'll just add the clocks as required on
new DTs.
Fixes: ebc4969ae1 ("dt-bindings: usb: mtk-xhci: Make all clocks required")
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220708192605.43351-1-nfraprado@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It allows to reset prevent_medium_removal flag and "eject" the image.
This can be useful to free the drive from a hunging host or if the host
continues to use the drive even after unmounting (Linux does this).
It's also a bit like using an unfolded paperclip on an optical drive.
Previously, the undocumented method of sending SIGUSR1 to a special
"file-storage" kernel thread could be used for these purposes,
but when using multiple storages there was no way to distinguish
one from the other, so we had to send a signal to everyone.
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Maxim Devaev <mdevaev@gmail.com>
Link: https://lore.kernel.org/r/20220711102956.19642-1-mdevaev@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Call onboard_hub_create/destroy_pdevs() from hub_probe/disconnect()
to create/destroy platform devices for onboard USB hubs that may be
connected to the hub. The onboard hubs must have nodes in the
device tree.
onboard_hub_create/destroy_pdevs() are NOPs unless
CONFIG_USB_ONBOARD_HUB=y/m.
Also add a field to struct usb_hub to keep track of the onboard hub
platform devices that are owned by the hub.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20220630123445.v24.4.Ic9dd36078f9d803de82ca01a6700c58b8e4de27e@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The main issue this driver addresses is that a USB hub needs to be
powered before it can be discovered. For discrete onboard hubs (an
example for such a hub is the Realtek RTS5411) this is often solved
by supplying the hub with an 'always-on' regulator, which is kind
of a hack. Some onboard hubs may require further initialization
steps, like changing the state of a GPIO or enabling a clock, which
requires even more hacks. This driver creates a platform device
representing the hub which performs the necessary initialization.
Currently it only supports switching on a single regulator, support
for multiple regulators or other actions can be added as needed.
Different initialization sequences can be supported based on the
compatible string.
Besides performing the initialization the driver can be configured
to power the hub off during system suspend. This can help to extend
battery life on battery powered devices which have no requirements
to keep the hub powered during suspend. The driver can also be
configured to leave the hub powered when a wakeup capable USB device
is connected when suspending, and power it off otherwise.
Technically the driver consists of two drivers, the platform driver
described above and a very thin USB driver that subclasses the
generic driver. The purpose of this driver is to provide the platform
driver with the USB devices corresponding to the hub(s) (a hub
controller may provide multiple 'logical' hubs, e.g. one to support
USB 2.0 and another for USB 3.x).
Co-developed-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20220630123445.v24.3.I7c9a1f1d6ced41dd8310e8a03da666a32364e790@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add function wake notification to support function remote wakeup,
currently assume the composite device only enable function wake
for the first interface.
Forward request to function driver when the recipient is an interface,
including:
GetStatus() request to the first interface in a function returns the
information about 'function remote wakeup' and 'function remote wakeup
capalbe';
SetFeature request of FUNCTION_SUSPEND to an interface recipient, the
controller driver saves the suspend option;
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220708071903.25752-5-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is capable of supporting usb3 dual role if there is at least one
usb3 port for device and xhci controller, we can check it from the
controller's capability, so no need the property "mediatek,usb3-drd"
anymore, but I find the property is not decribed in dt-binding.
Meanwhile, also take into account if the u3 port is disabled when the
u3 phy is shared with pcie.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220708071903.25752-4-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We may want to disable device's usb3 port when the combo phy is switched
from usb3 mode to pcie mode for some projects.
Meanwhile rename member @is_u3_ip to @u3_capable to avoid misleading, due
to the member's value may be changed when disable usb3 port, but the
controller is still a usb3 IP which also tells us how to manage the fifo.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220708071903.25752-3-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver won't probe on a LAN9668 because the pinctrl driver isn't
ready yet. Probe deferral is not supported because the init section
is already discarded. With fw_devlink enabled, the probe won't even
be called. Convert the driver to a proper platform driver.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220705131951.1388968-2-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The event classes udc_log_ep and udc_log_req both declare:
__dynamic_array(char, name, UDC_TRACE_STR_MAX)
Which will reserve UDC_TRACE_STR_MAX bytes on the ring buffer for the
event to write in name. It then uses snprintf() to write into that space.
Assuming that the string being copied is nul terminated, it is better to
just use the __string() helper. That way only the size of the string is
saved into the ring buffer and not the max size (yes, the entire
UDC_TRACE_STR_MAX is used in the trace event, and anything not used is
just junk in the ring buffer). Worse, there's also meta data saved into
the event that denotes where the string is stored in the event and also
saves its size, which is always going to be UDC_TRACE_STR_MAX.
Convert both to use the __string() and __assign_str() helpers that are for
this kind of use case.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Link: https://lore.kernel.org/r/20220703091449.317f94b1@rorschach.local.home
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mika writes:
thunderbolt: Changes for v5.20 merge window
This includes following Thunderbolt/USB4 changes for the v5.20 merge
window:
* Enable CL1 low power link state
* Add support for Intel Raptor Lake Thunderbolt/USB4 controller
* A couple of typos fixed.
All these have been in linux-next with no reported issues.
* tag 'thunderbolt-for-v5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: Fix typo in comment
thunderbolt: Add support for Intel Raptor Lake
thunderbolt: Fix some kernel-doc comments
thunderbolt: Change TMU mode to HiFi uni-directional once DisplayPort tunneled
thunderbolt: Add CL1 support for USB4 and Titan Ridge routers
thunderbolt: Change downstream router's TMU rate in both TMU uni/bidir mode
thunderbolt: Fix typos in CLx enabling
thunderbolt: CLx disable before system suspend only if previously enabled
thunderbolt: Silently ignore CLx enabling in case CLx is not supported
All of the clocks listed in the binding are always wired to the XHCI
controller hardware blocks on all SoCs. The reason some clocks were made
optional in the binding was to account for the fact that depending on
the SoC, some of the clocks might be fixed (ie not controlled by
software).
Given that the devicetree should represent the hardware, make all clocks
required in the binding. Subsequent patches will make the DTS changes to
specify fixed-clocks for the clocks that aren't controllable.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220623193702.817996-3-nfraprado@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull ARM SoC fixes from Arnd Bergmann:
"A number of fixes have accumulated, but they are largely for harmless
issues:
- Several OF node leak fixes
- A fix to the Exynos7885 UART clock description
- DTS fixes to prevent boot failures on TI AM64 and J721s2
- Bus probe error handling fixes for Baikal-T1
- A fixup to the way STM32 SoCs use separate dts files for different
firmware stacks
- Multiple code fixes for Arm SCMI firmware, all dealing with
robustness of the implementation
- Multiple NXP i.MX devicetree fixes, addressing incorrect data in DT
nodes
- Three updates to the MAINTAINERS file, including Florian Fainelli
taking over BCM283x/BCM2711 (Raspberry Pi) from Nicolas Saenz
Julienne"
* tag 'soc-fixes-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (29 commits)
ARM: dts: aspeed: nuvia: rename vendor nuvia to qcom
arm: mach-spear: Add missing of_node_put() in time.c
ARM: cns3xxx: Fix refcount leak in cns3xxx_init
MAINTAINERS: Update email address
arm64: dts: ti: k3-am64-main: Remove support for HS400 speed mode
arm64: dts: ti: k3-j721s2: Fix overlapping GICD memory region
ARM: dts: bcm2711-rpi-400: Fix GPIO line names
bus: bt1-axi: Don't print error on -EPROBE_DEFER
bus: bt1-apb: Don't print error on -EPROBE_DEFER
ARM: Fix refcount leak in axxia_boot_secondary
ARM: dts: stm32: move SCMI related nodes in a dedicated file for stm32mp15
soc: imx: imx8m-blk-ctrl: fix display clock for LCDIF2 power domain
ARM: dts: imx6qdl-colibri: Fix capacitive touch reset polarity
ARM: dts: imx6qdl: correct PU regulator ramp delay
firmware: arm_scmi: Fix incorrect error propagation in scmi_voltage_descriptors_get
firmware: arm_scmi: Avoid using extended string-buffers sizes if not necessary
firmware: arm_scmi: Fix SENSOR_AXIS_NAME_GET behaviour when unsupported
ARM: dts: imx7: Move hsic_phy power domain to HSIC PHY node
soc: bcm: brcmstb: pm: pm-arm: Fix refcount leak in brcmstb_pm_probe
MAINTAINERS: Update BCM2711/BCM2835 maintainer
...
Pull hotfixes from Andrew Morton:
"Minor things, mainly - mailmap updates, MAINTAINERS updates, etc.
Fixes for this merge window:
- fix for a damon boot hang, from SeongJae
- fix for a kfence warning splat, from Jason Donenfeld
- fix for zero-pfn pinning, from Alex Williamson
- fix for fallocate hole punch clearing, from Mike Kravetz
Fixes for previous releases:
- fix for a performance regression, from Marcelo
- fix for a hwpoisining BUG from zhenwei pi"
* tag 'mm-hotfixes-stable-2022-06-26' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mailmap: add entry for Christian Marangi
mm/memory-failure: disable unpoison once hw error happens
hugetlbfs: zero partial pages during fallocate hole punch
mm: memcontrol: reference to tools/cgroup/memcg_slabinfo.py
mm: re-allow pinning of zero pfns
mm/kfence: select random number before taking raw lock
MAINTAINERS: add maillist information for LoongArch
MAINTAINERS: update MM tree references
MAINTAINERS: update Abel Vesa's email
MAINTAINERS: add MEMORY HOT(UN)PLUG section and add David as reviewer
MAINTAINERS: add Miaohe Lin as a memory-failure reviewer
mailmap: add alias for jarkko@profian.com
mm/damon/reclaim: schedule 'damon_reclaim_timer' only after 'system_wq' is initialized
kthread: make it clear that kthread_create_on_node() might be terminated by any fatal signal
mm: lru_cache_disable: use synchronize_rcu_expedited
mm/page_isolation.c: fix one kernel-doc comment
Pull perf tools fixes from Arnaldo Carvalho de Melo:
- Enable ignore_missing_thread in 'perf stat', enabling counting with
'--pid' when threads disappear during counting session setup
- Adjust output data offset for backward compatibility in 'perf inject'
- Fix missing free in copy_kcore_dir() in 'perf inject'
- Fix caching files with a wrong build ID
- Sync drm, cpufeatures, vhost and svn headers with the kernel
* tag 'perf-tools-fixes-for-v5.19-2022-06-26' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
tools headers UAPI: Synch KVM's svm.h header with the kernel
tools include UAPI: Sync linux/vhost.h with the kernel sources
perf stat: Enable ignore_missing_thread
perf inject: Adjust output data offset for backward compatibility
perf trace beauty: Fix generation of errno id->str table on ALT Linux
perf build-id: Fix caching files with a wrong build ID
tools headers cpufeatures: Sync with the kernel sources
tools headers UAPI: Sync drm/i915_drm.h with the kernel sources
perf inject: Fix missing free in copy_kcore_dir()
Pull btrfs fixes from David Sterba:
- zoned relocation fixes:
- fix critical section end for extent writeback, this could lead
to out of order write
- prevent writing to previous data relocation block group if space
gets low
- reflink fixes:
- fix race between reflinking and ordered extent completion
- proper error handling when block reserve migration fails
- add missing inode iversion/mtime/ctime updates on each iteration
when replacing extents
- fix deadlock when running fsync/fiemap/commit at the same time
- fix false-positive KCSAN report regarding pid tracking for read locks
and data race
- minor documentation update and link to new site
* tag 'for-5.19-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
Documentation: update btrfs list of features and link to readthedocs.io
btrfs: fix deadlock with fsync+fiemap+transaction commit
btrfs: don't set lock_owner when locking extent buffer for reading
btrfs: zoned: fix critical section of relocation inode writeback
btrfs: zoned: prevent allocation from previous data relocation BG
btrfs: do not BUG_ON() on failure to migrate space when replacing extents
btrfs: add missing inode updates on each iteration when replacing extents
btrfs: fix race between reflinking and ordered extent completion
Pull dma-mapping fix from Christoph Hellwig:
- pass the correct size to dma_set_encrypted() when freeing memory
(Dexuan Cui)
* tag 'dma-mapping-5.19-2022-06-26' of git://git.infradead.org/users/hch/dma-mapping:
dma-direct: use the correct size for dma_set_encrypted()
Pull fbdev fixes from Helge Deller:
"Two bug fixes for the pxa3xx and intelfb drivers:
- pxa3xx-gcu: Fix integer overflow in pxa3xx_gcu_write
- intelfb: Initialize value of stolen size
The other changes are small cleanups, simplifications and
documentation updates to the cirrusfb, skeletonfb, omapfb,
intelfb, au1100fb and simplefb drivers"
* tag 'for-5.19/fbdev-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev:
video: fbdev: omap: Remove duplicate 'the' in comment
video: fbdev: omapfb: Align '*' in comment
video: fbdev: simplefb: Check before clk_put() not needed
video: fbdev: au1100fb: Drop unnecessary NULL ptr check
video: fbdev: pxa3xx-gcu: Fix integer overflow in pxa3xx_gcu_write
video: fbdev: skeletonfb: Convert to generic power management
video: fbdev: cirrusfb: Remove useless reference to PCI power management
video: fbdev: intelfb: Initialize value of stolen size
video: fbdev: intelfb: Use aperture size from pci_resource_len
video: fbdev: skeletonfb: Fix syntax errors in comments
Pull parisc architecture fixes from Helge Deller:
- enable ARCH_HAS_STRICT_MODULE_RWX to prevent a boot crash on c8000
machines
- flush all mappings of a shared anonymous page on PA8800/8900 machines
via flushing the whole data cache. This may slow down such machines
but makes sure that the cache is consistent
- Fix duplicate definition build error regarding fb_is_primary_device()
* tag 'for-5.19/parisc-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Enable ARCH_HAS_STRICT_MODULE_RWX
parisc: Fix flush_anon_page on PA8800/PA8900
parisc: align '*' in comment in math-emu code
parisc/stifb: Fix fb_is_primary_device() only available with CONFIG_FB_STI
Pull xtensa fixes from Max Filippov:
- fix OF reference leaks in xtensa arch code
- replace '.bss' with '.section .bss' to fix entry.S build with old
assembler
* tag 'xtensa-20220626' of https://github.com/jcmvbkbc/linux-xtensa:
xtensa: change '.bss' to '.section .bss'
xtensa: xtfpga: Fix refcount leak bug in setup
xtensa: Fix refcount leak bug in time.c
Pull powerpc fixes from Michael Ellerman:
- A fix for a CMA change that broke booting guests with > 2G RAM on
Power8 hosts.
- Fix the RTAS call filter to allow a special case that applications
rely on.
- A change to our execve path, to make the execve syscall exit
tracepoint work.
- Three fixes to wire up our various RNGs earlier in boot so they're
available for use in the initial seeding in random_init().
- A build fix for when KASAN is enabled along with
STRUCTLEAK_BYREF_ALL.
Thanks to Andrew Donnellan, Aneesh Kumar K.V, Christophe Leroy, Jason
Donenfeld, Nathan Lynch, Naveen N. Rao, Sathvika Vasireddy, Sumit
Dubey2, Tyrel Datwyler, and Zi Yan.
* tag 'powerpc-5.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/powernv: wire up rng during setup_arch
powerpc/prom_init: Fix build failure with GCC_PLUGIN_STRUCTLEAK_BYREF_ALL and KASAN
powerpc/rtas: Allow ibm,platform-dump RTAS call with null buffer address
powerpc: Enable execve syscall exit tracepoint
powerpc/pseries: wire up rng during setup_arch()
powerpc/microwatt: wire up rng during setup_arch()
powerpc/mm: Move CMA reservations after initmem_init()
Pull Kbuild fixes from Masahiro Yamada:
- Fix modpost to detect EXPORT_SYMBOL marked as __init or__exit
- Update the supported arch list in the LLVM document
- Avoid the second link of vmlinux for CONFIG_TRIM_UNUSED_KSYMS
- Avoid false __KSYM___this_module define in include/generated/autoksyms.h
* tag 'kbuild-fixes-v5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: Ignore __this_module in gen_autoksyms.sh
kbuild: link vmlinux only once for CONFIG_TRIM_UNUSED_KSYMS (2nd attempt)
Documentation/llvm: Update Supported Arch table
modpost: fix section mismatch check for exported init/exit sections
Pull exfat fix from Namjae Jeon:
- Use updated exfat_chain directly instead of snapshot values in
rename.
* tag 'exfat-for-5.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/linkinjeon/exfat:
exfat: use updated exfat_chain directly during renaming
