We don't need init_hwif_ali15x3() on the PowerPC systems either.
Before:
ALI15X3: IDE controller (0x10b9:0x5229 rev 0xc8) at PCI slot 0001:03:1f.0
ALI15X3: 100% native mode on irq 19
ide0: BM-DMA at 0x1120-0x1127
ide1: BM-DMA at 0x1128-0x112f
hda: SONY DVD RW AW-Q170A, ATAPI CD/DVD-ROM drive
hda: UDMA/66 mode selected
ide0: Disabled unable to get IRQ 14.
ide0: failed to initialize IDE interface
ide1: Disabled unable to get IRQ 15.
ide1: failed to initialize IDE interface
After:
ALI15X3: IDE controller (0x10b9:0x5229 rev 0xc8) at PCI slot 0001:03:1f.0
ALI15X3: 100% native mode on irq 19
ide0: BM-DMA at 0x1120-0x1127
ide1: BM-DMA at 0x1128-0x112f
hda: SONY DVD RW AW-Q170A, ATAPI CD/DVD-ROM drive
hda: UDMA/66 mode selected
ide0 at 0x1100-0x1107,0x110a on irq 19
ide1 at 0x1110-0x1117,0x111a on irq 19
hda: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
ide0 works well, though I can't test ide1, it isn't traced out on
the board.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Some change to the IDE layer are causing the siimage driver to crash
at boot with a NULL dereference. This is due to the sil_dma_ops not
containing all the necessary pointers. I suppose it used to just
"override" the defaults while now, it needs to contain everything.
[bart: while at it: sil_dma_ops should be const now (pointed out by Sergei)]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>,
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: Skip I/O merges when disabled
block: add large command support
block: replace sizeof(rq->cmd) with BLK_MAX_CDB
ide: use blk_rq_init() to initialize the request
block: use blk_rq_init() to initialize the request
block: rename and export rq_init()
block: no need to initialize rq->cmd with blk_get_request
block: no need to initialize rq->cmd in prepare_flush_fn hook
block/blk-barrier.c:blk_ordered_cur_seq() mustn't be inline
block/elevator.c:elv_rq_merge_ok() mustn't be inline
block: make queue flags non-atomic
block: add dma alignment and padding support to blk_rq_map_kern
unexport blk_max_pfn
ps3disk: Remove superfluous cast
block: make rq_init() do a full memset()
relay: fix splice problem
Use proc_create()/proc_create_data() to make sure that ->proc_fops and ->data
be setup before gluing PDE to main tree.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Peter Osterlund <petero2@telia.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Neil Brown <neilb@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a preparation for changing rq->cmd from the static array to a
pointer.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This converts ide to use blk_rq_init to initialize the request.
This is a preparation for large command support, which needs to
initialize the request in a proper way (that is, just doing a memset()
will not work).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Fix 18 errors and several warnings given by checkpatch.pl:
- use of C99 // comments;
- trailing whitespace;
- 'switch' and 'case' not at the same indentation level;
- no space before the open parenthesis of the 'if' and 'switch' statements;
- space between function name and open parenthesis (though I have introduced
such warnins in some places since the code looks prettier with the spaces);
- including <asm/io.h> instead of <linux/io.h>;
- line over 80 characters.
In addition to these changes, also do the following:
- make the arrays in sil_set_pio_mode() 'static', and make the arrays in
sil_set_dma_mode() 'static const';
- change the string of the 'if' statements into the 'switch' statement in
sil_pata_udma_filter();
- drop the needless '==' operators from the 'if' statements where a condition
is a mere bit test;
- remove needless initializer for the 'tmp' variable in init_chipset_siimage();
- beautify groups of the variable initializers and assignment operators;
- add new line after variable definitions;
- remove new line between the comment and the statements it refers to;
- remove needless curly braces and parentheses;
- fix typos, capitalize acronyms, etc. in the comments...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ETRAX_IDE was marked as broken last year with the comment
"it doesn't even compile currently".
Remove it since it won't get fixed in the near future.
On Mon, Apr 14, 2008 at 02:50:19PM +0200, Mikael Starvik wrote:
> You can remove it for now and we will resubmit a new if/when we get around
> to fix it.
[bart: ported it over IDE tree]
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Cc: Jesper Nilsson <Jesper.Nilsson@axis.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use 'hwif->dma_base + {4,8}' instead of hwif->dma_prdtable in
{ide,scc}_dma_setup().
* Remove no longer needed ->dma_prdtable field from ide_hwif_t.
While at it:
* Use ATA_DMA_TABLE_OFS define.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use 'hwif->dma_base + {1,3}' instead of hwif->dma_vendor{1,3} in
pdc202xx_new host driver.
* Remove no longer needed ->dma_vendor{1,3} fields from ide_hwif_t.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ->dma_host_set and ->dma_start methods (+ __scc_dma_end() helper)
so scc_ide_{in,out}b() can be used directly.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Skip "VLB sync" in ata_{in,out}put_data() if host uses MMIO.
* Use I/O ops directly in ata_vlb_sync() an drop no longer needed
'ide_drive_t *drive' argument.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_pad_transfer() helper (which uses ->{in,out}put_data methods
internally so the transfer is also padded to drive+host requirements)
and use it instead of ide_atapi_{write_zeros,discard_data}().
* Remove no longer needed ide_atapi_{write_zeros,discard_data}().
Cc: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove no longer used ->INW and ->OUTW methods.
While at it:
* scc_pata.c: scc_ide_{out,in}w() is called only in scc_tf_{load,read}()
so inline it there.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ->tf_read method so out{b,w}(), in{b,w}() and superio_ide_inb()
can be used directly.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ->tf_{load,read} methods so scc_ide_{outb,outw,inb,inw}()
can be used directly.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ->tf_{load,read} methods so outb()/inb() and mm_outw()/mm_inw()
can be used directly.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ->tf_{load,read} methods so cris_ide_{outb,outw,inb,inw}()
can be used directly.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->tf_load and ->tf_read methods to ide_hwif_t and set the default
methods in default_hwif_transport().
* Use ->tf_{load,read} instead o calling ide_tf_{load,read}() directly.
* Make ide_tf_{load,read}() static.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Factor out debugging code from ide_tf_load() to ide_tf_dump() helper
and update ide_tf_load() users accordingly.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ide_execute_pkt_cmd() helper for executing PACKET command,
then convert ATAPI device drivers to use it.
As a nice side-effect this fixes ide-{floppy,tape,scsi} w.r.t.
ide_lock taking (ide-cd was OK).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Always use ->OUTBSYNC method for executing commands so the posting is done
if needed (this affects only pmac and scc_pata host drivers at the moment).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* proc_reports_siimage() is now only called by init_chipset_siimage()
so inline it there.
* Use array instead of switch statement for reporting clock modes.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add sil_iowrite{8,16,32}() and sil_ioread{8,16}() helpers, then use them to
merge code accessing configuration registers through PCI and MMIO together.
[ because of this SATA initialization bits from setup_mmio_siimage() are
moved to init_chipset_siimage() ]
This also cuts code size a bit:
text data bss dec hex filename
4437 164 0 4601 11f9 drivers/ide/pci/siimage.o.before
3979 164 0 4143 102f drivers/ide/pci/siimage.o.after
While at it:
* Use I/O ops directly instead of using ->IN{B,W} and ->OUT{B,W}.
* Fixup CodingStyle in setup_mmio_siimage().
* Rename 'tmpbyte' variable to 'tmp' in init_chipset_siimage().
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Do clocking register posting earlier in setup_mmio_siimage()
to match code in init_chipset_siimage().
This is a preparation for the next patch which merges PCI and MMIO
code paths together.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use ins{w,l}()/outs{w,l}() and __ide_mm_ins{w,l}()/__ide_mm_outs{w,l}()
directly in ata_{in,out}put_data() (by using IDE_HFLAG_MMIO host flag to
decide which I/O ops are required).
* Remove no longer needed ->INS{W,L} and ->OUTS{W,L} methods (ide-h8300,
au1xxx-ide and scc_pata implement their own ->{in,out}put_data methods).
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_HFLAG_MMIO host flag and set it for hosts which use
default_hwif_mmiops().
v2:
* Fix kernel panic in pmac host driver (',' should be '|').
Thanks to Kamalesh for reporting it + testing the fix
and to Andrew for hinting me about the source of the issue.
Cc: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
v2:
* Update ->{in,out}_data methods to take 'struct request *rq' argument.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
v2:
* Update ->{in,out}_data methods to take 'struct request *rq' argument.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
v2:
* Update ->{in,out}_data methods to take 'struct request *rq' argument
(thanks to Stephen Rothwell for catching it).
There should be no functional changes caused by this patch.
Cc: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Cc: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Merge ->atapi_{in,out}put_bytes and ->ata_{in,out}put_data methods
into new ->{in,out}put_data methods which take number of bytes to
transfer as an argument and always do padding.
While at it:
* Use 'hwif' or 'drive->hwif' instead of 'HWIF(drive)'.
There should be no functional changes caused by this patch (all users
of ->ata_{in,out}put_data methods were using multiply-of-4 word counts).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->atapi_{in,out}put_bytes and ->ata_{in,out}put_data methods to
falconide and q40ide host drivers (->ata_* methods are implemented on
top of ->atapi_* methods so they also do byte-swapping now).
* Cleanup atapi_{in,out}put_bytes().
v2:
* Add 'struct request *rq' argument to ->ata_{in,out}put_data methods
and don't byte-swap disk fs requests (we shouldn't un-swap fs requests
because fs itself is stored byte-swapped on the disk) - this is how
things were done before the patch (ideally device mapper should be
used instead but it would break existing setups and would have some
performance impact).
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michael Schmitz <schmitz@debian.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Richard Zidlicky <rz@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On Monday 28 April 2008, Sergei Shtylyov wrote:
> Hello, I wrote:
>
> > Fix these warnings emitted when compiling drivers/ide/mips/au1xxx-ide.c:
>
> > include/asm/mach-au1x00/au1xxx_ide.h:137: warning: 'auide_tune_drive' declared
> > `static' but never defined
> > include/asm/mach-au1x00/au1xxx_ide.h:138: warning: 'auide_tune_chipset' declared
> > `static' but never defined
>
> > by wiping out the whole "function prototyping" section from the header file
> > <asm-mips/mach-au1x00/au1xxx_ide.h> as it mostly declared functions that are
> > already dead in the IDE driver; move the only useful prototype into the driver.
> >
> > Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
>
> > ---
> > I'm not sure thru which tree this should go -- probably thru Linux/MIPS one...
>
> > Bart, au1xxx-ide-fix-mwdma-support.patch will probably need to be updated to
> > remove that added prototype since it won't be needed anymore...
>
> Which you haven't done either in that patch or in
> au1xxx-ide-use-init_dma-method.patch. So, face the consequences:
>
> drivers/ide/mips/au1xxx-ide.c:456: error: conflicting types for 'auide_ddma_init'
> drivers/ide/mips/au1xxx-ide.c:51: error: previous declaration of
> 'auide_ddma_init' was here
> drivers/ide/mips/au1xxx-ide.c:456: error: conflicting types for 'auide_ddma_init'
> drivers/ide/mips/au1xxx-ide.c:51: error: previous declaration of
> 'auide_ddma_init' was here
> drivers/ide/mips/au1xxx-ide.c:51: warning: 'auide_ddma_init' used but never
> defined
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since both the IDE interface and SMC 91C111 Ethernet chip are on-board
devices, not SOC devices, move the platform device registration form the
common to the board specific code.
While at it, remove semicolon (which didn't break compilation only by
chance) from the AU1XXX_ATA_DDMA_REQ macro and do some renaming:
- change 'au1200_ide0_' variable name prefix to the mere 'ide_';
- change 'smc91x_' variable name prefix to 'smc91c111_' since that's the
name of the chip used on the boards;
- drop 'AU1XXX_' prefix from the names of macros describing IDE and Ethernet
on-board devices;
- change 'SMC91111_' to 'SMC91C111_', change 'IRQ' to 'INT' in the names of
the macros describing the Ethernet chip for consistency with the IDE
macros;
- change 'ATA_' to 'IDE_' and 'OFFSET' to 'SHIFT' (since this value is
indeed a shift count) in the names of the macros describing the IDE
interface.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Get rid of the pipeline merge stage but retain the chrdev req caching
functionality by using a merge buffer tape->merge_bh which is flushed in chunks
of several blocks at a time. Also, remove last references to pipelining, e.g.
typedef idetape_stage_s.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This is the size of the merge buffer.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It always returns 0 which has no effect on tape positioning calculation so
simplify it by converting its type to void, bringing no functional change to the
driver.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
