Add support to configure the GPIO pin to the specific configuration.
The GPIO pin can be configured as GPO, IRQ, SDOUT2, PDMCLK, MICBASE_EN,
GPI, MCLK, SDIN, PDMDIN1, PDMDIN2, PDMDIN3 or PDMDIN4 and the output
drive can be configured with various configuration.
Signed-off-by: Camel Guo <camelg@axis.com>
Link: https://lore.kernel.org/r/20200918114025.18205-2-camel.guo@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Ak4458 can't support DSD512 format, but ak4497 can, so add
a new enum variable (enum ak4458_type) in ak4458_drvdata to
distinguish these two platforms.
Ak4497 has two kinds of DSD input pin, it can be selected by
the dsd-path property from DT.
In hw_params(), bit clock is calculated according to different
DSD format (DSD64, DSD128, DSD256, DSD512), then registers
are configured.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1600178220-28973-2-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add code to allow the ASI Tx output to be placed into High-z mode
during unused ASI cycles. This allows for other devices that may be on
the bus to drive the ASI out. By default the 320adcx140 sends 0's for
unused cycles.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200915190606.1744-4-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
To avoid the actual PLL settings to differ from the state expected by
the clock driver, the codec should only be fully reset before the clocks
are registered. But we also need to ensure that the software reset
happens at all before clock registration, as not all boards have a reset
GPIO.
Move the software reset from aic32x4_component_probe() to
aic32x4_probe() and reorder the reset and registration sequence:
1. Reset via GPIO (if available)
2. Reset via software
3. Register component
4. Register clocks
Note that aic32x4_component_probe() is only called after aic32x4_probe()
has finished, so the reset in aic32x4_component_probe() was happening too
late.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20200902133043.19504-2-matthias.schiffer@ew.tq-group.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulators need to be disabled in the aic32x4_register_clocks()
failure case as well.
Fixes: 9d4befff5a ("ASoC: codec: tlv3204: Moving GPIO reset and add ADC reset")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20200902133043.19504-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the BCLK inversion for DSP modes
This is how it is defined by ASoC:
* BCLK:
* - "normal" polarity means signal is available at rising edge of BCLK
* - "inverted" polarity means signal is available at falling edge of BCLK
The adcx140 defines the BCLK edge based on coding type.
The PCM (DSP_A/B) should drive on rising and sample on falling edge, so
from ASoC pov, it is IB_NF. But from the codec pov if it is configured in
DSP mode, then the BCLK should not be inverted, defaults to the coding
standard.
For i2s, it is NB_NF from ASoC pov (drive on falling, sample on rising).
>From the codec's pov BCLK should not invert either, as this is the default
for the coding.
So, inversion must take the format into account:
IB_NF + DSP_A/B == the codec bclk inversion should be disabled
NB_NF + DSP_A/B == the codec bclk inversion should be enabled
NB_NF + I2S == the codec bclk inversion should be disabled
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200915190606.1744-2-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It was observed that if the device was active and register writes were
performed there were some unwanted behaviors particularly when writing
the word length and some filter options. So when writing to the device
the device should be placed in sleep mode and then exit sleep mode once
the register update is complete.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200915190606.1744-1-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
According to its datasheet, the digital gain should be -100 dB when
CHx_DVOL is 1 and 27 dB when CHx_DVOL is 255. But with the current
dig_vol_tlv, "Digital CHx Out Volume" shows 27.5 dB if CHx_DVOL is 255
and -95.5 dB if CHx_DVOL is 1. This commit fixes this bug.
Fixes: 689c7655b5 ("ASoC: tlv320adcx140: Add the tlv320adcx140 codec driver family")
Signed-off-by: Camel Guo <camelg@axis.com>
Link: https://lore.kernel.org/r/20200908090417.16695-1-camel.guo@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Adds rt1015p codec driver.
Rt1015p is a rt1015 variant.
- It doesn't support I2C.
- It only supports S24, 48kHz, 64FS.
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20200910042949.3795682-2-tzungbi@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The parity calculation is not reset on a Severe Reset, which leads to
misleading/harmless errors reported on startup. The addition of a
quirk helps filter out such errors while leaving the error checks on
in steady-state.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20200908134521.6781-6-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add a slave-level property and program the SCP_INT1_MASK as desired by
the codec driver. Since there is no DisCo property this has to be an
implementation-specific firmware property or hard-coded in the driver.
The only functionality change is that implementation-defined
interrupts are no longer set for amplifiers - those interrupts are
typically for jack detection or acoustic event detection/hotwording.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20200908134521.6781-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
According to its datasheet, after reset this codec goes into sleep
mode. In this mode, any register accessing should be avoided except for
exiting sleep mode. Hence this commit moves SLEEP_CFG access before any
register accessing.
Signed-off-by: Camel Guo <camelg@axis.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200908083521.14105-2-camel.guo@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Mt6359 platform device is instantiated by mfd_add_devices(). In the
case, dev->of_node is NULL so that mt6359_parse_dt() always fails to
parse the desired DT properties.
Gets the DT properties via dev->parent->of_node.
Fixes: 8061734ab6 ("ASoC: mediatek: mt6359: add codec driver")
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20200908070044.1142644-1-tzungbi@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
port_ready will be changed to a fixed array in sdw.h and all initialization
work will be done at soundwire side in the following patch. So remove them
from codec drivers.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20200831134318.11443-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In adcx140_i2c_probe, adcx140->dev is accessed before its
initialization. This commit fixes this bug.
Fixes: 689c7655b5 ("ASoC: tlv320adcx140: Add the tlv320adcx140 codec driver family")
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Camel Guo <camel.guo@axis.com>
Link: https://lore.kernel.org/r/20200901135736.32036-1-camel.guo@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The probe of rt5682 is pretty slow. A quick measurement shows that it
takes ~650 ms on at least one board. There's no reason to block all
other drivers waiting for this probe to finish. Set the flag to allow
other drivers to probe while we're probing.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200828162005.1.I4f67f494c4f759b0e5c7f487e040dfdcf16e0876@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
When the wm8958_mic_detect, wm8994_mic_detect functions get called from
the machine driver, e.g. from the card's late_probe() callback, the CODEC
device may be PM runtime suspended and any regmap writes have no effect.
Add PM runtime calls to these functions to ensure the device registers
are updated as expected.
This suppresses an error during boot
"wm8994-codec: ASoC: error at snd_soc_component_update_bits on wm8994-codec"
caused by the regmap access error due to the cache_only flag being set.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200827173357.31891-2-s.nawrocki@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The WM8994_MICBIAS register is not available in the WM1811 CODEC so skip
initialization of that register for that device.
This suppresses an error during boot:
"wm8994-codec: ASoC: error at snd_soc_component_update_bits on wm8994-codec"
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200827173357.31891-1-s.nawrocki@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the audio routing map to enable the digital mic paths when the
analog mic paths are not enabled.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200828112855.10112-1-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Changing filter type without disabling codec results in filter
malfunction. Disable codec when changing filter type.
Signed-off-by: Pavel Dobias <dobias@2n.cz>
Link: https://lore.kernel.org/r/20200827102528.29677-1-dobias@2n.cz
Signed-off-by: Mark Brown <broonie@kernel.org>
devm_regmap_init_sdw() returns a valid pointer on success or ERR_PTR on
failure which should be checked with IS_ERR. Also use PTR_ERR for
returning error codes.
Reported-by: Takashi Iwai <tiwai@suse.de>
Fixes: 7d2a5f9ae4 ("ASoC: rt700: add rt700 codec driver")
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200826163340.3249608-6-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
devm_regmap_init_sdw() returns a valid pointer on success or ERR_PTR on
failure which should be checked with IS_ERR. Also use PTR_ERR for
returning error codes.
Reported-by: Takashi Iwai <tiwai@suse.de>
Fixes: d1ede0641b ("ASoC: rt715: add RT715 codec driver")
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200826163340.3249608-5-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
devm_regmap_init_sdw() returns a valid pointer on success or ERR_PTR on
failure which should be checked with IS_ERR. Also use PTR_ERR for
returning error codes.
Reported-by: Takashi Iwai <tiwai@suse.de>
Fixes: 320b8b0d13 ("ASoC: rt711: add rt711 codec driver")
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200826163340.3249608-4-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
devm_regmap_init_sdw() returns a valid pointer on success or ERR_PTR on
failure which should be checked with IS_ERR. Also use PTR_ERR for
returning error codes.
Reported-by: Takashi Iwai <tiwai@suse.de>
Fixes: a87a6653a2 ("ASoC: rt1308-sdw: add rt1308 SdW amplifier driver")
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200826163340.3249608-3-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
devm_regmap_init_sdw() returns a valid pointer on success or ERR_PTR on
failure which should be checked with IS_ERR. Also use PTR_ERR for
returning error codes.
Reported-by: Takashi Iwai <tiwai@suse.de>
Fixes: 56a5b7910e ("ASoC: codecs: max98373: add SoundWire support")
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200826163340.3249608-2-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The ARRAY_SIZE() is the number of the elements but we want to use the
number of bytes. Fortunately, in this case the value is the same so it
doesn't affect runtime.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200825104623.GA278587@mwanda
Signed-off-by: Mark Brown <broonie@kernel.org>
Some sound card try to set 0 Hz as reset, but it is impossible.
This patch ignores it to avoid error return.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87a6yjy5sy.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This series updates the tables used to select SoundWire configurations
for CometLake and TigerLake, and adds support for SDCA (SoundWire
Device Class for Audio) codecs in the common machine driver. These
codec drivers are still being tested on early silicon/boards and will
be contributed at a later time.
For TigerLake Chromebooks a new DMI quirk is added, as well as a means
to override the topology names. A pm_runtime fix is also provided to
deal with playback/capture dependencies with an amplifier w/
feedback. I also included a minor codec correction for the TGL
amplifier.
Bard Liao (5):
ASoC: Intel: modify SoundWire version id in acpi match table
ASoC: Intel: sof_sdw: check SoundWire version when matching codec
ASoC: Intel: sof_sdw: rename id as part_id
ASoC: Intel: sof_sdw: add rt711 rt1316 rt714 SDCA codec support.
ASoC: Intel: sof_sdw: clean-up inclusion of header files
Pierre-Louis Bossart (5):
ASoC: Intel: soc-acpi: cnl: add support for rt5682 on SoundWire link2
ASoC: Intel: sof-soundwire: add support for rt5682 on link2
ASoC: Intel: soc-acpi: mirror CML and TGL configurations
ASoC: Intel: soc-acpi: add support for SDCA boards
ASoC: codecs: max98373-sdw: add missing test on resume
Rander Wang (2):
ASoC: Intel: tgl_max98373: fix a runtime pm issue in multi-thread case
ASoC: Intel: sof_sdw: Add support for product Ripto
Sathyanarayana Nujella (2):
ASoC: Intel: sof_rt5682: override quirk data for tgl_max98373_rt5682
ASoC: SOF: Add topology filename override based on dmi data match
sound/soc/codecs/max98373-sdw.c | 3 +
sound/soc/intel/boards/Kconfig | 3 +
sound/soc/intel/boards/Makefile | 7 +-
sound/soc/intel/boards/sof_maxim_common.c | 7 +-
sound/soc/intel/boards/sof_rt5682.c | 13 ++
sound/soc/intel/boards/sof_sdw.c | 98 +++++++---
sound/soc/intel/boards/sof_sdw_common.h | 22 ++-
sound/soc/intel/boards/sof_sdw_dmic.c | 1 +
sound/soc/intel/boards/sof_sdw_max98373.c | 2 +
sound/soc/intel/boards/sof_sdw_rt1308.c | 2 +
sound/soc/intel/boards/sof_sdw_rt1316.c | 113 ++++++++++++
sound/soc/intel/boards/sof_sdw_rt5682.c | 2 +
sound/soc/intel/boards/sof_sdw_rt700.c | 2 +
sound/soc/intel/boards/sof_sdw_rt711.c | 2 +
sound/soc/intel/boards/sof_sdw_rt711_sdca.c | 174 ++++++++++++++++++
sound/soc/intel/boards/sof_sdw_rt715_sdca.c | 42 +++++
.../intel/common/soc-acpi-intel-cml-match.c | 79 +++++++-
.../intel/common/soc-acpi-intel-cnl-match.c | 33 +++-
.../intel/common/soc-acpi-intel-icl-match.c | 10 +-
.../intel/common/soc-acpi-intel-tgl-match.c | 165 ++++++++++++++++-
sound/soc/sof/intel/hda.c | 8 +-
sound/soc/sof/sof-pci-dev.c | 24 +++
22 files changed, 764 insertions(+), 48 deletions(-)
create mode 100644 sound/soc/intel/boards/sof_sdw_rt1316.c
create mode 100644 sound/soc/intel/boards/sof_sdw_rt711_sdca.c
create mode 100644 sound/soc/intel/boards/sof_sdw_rt715_sdca.c
base-commit: fcea8b023a
--
2.25.1
"AVDD" is for analog power supply, "DVDD" is for digital power
supply, they can improve the power management.
As the regulator is enabled in pm runtime resume, which is
behind the component driver probe, so accessing registers in
component driver probe will fail. Fix this issue by enabling
regcache_cache_only after pm_runtime_enable.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1598190877-9213-2-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
All existing SoundWire codecs follow the same pattern on resume,
except for this codec which doesn't test if the hardware is
initialized.
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200821195603.215535-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A collection of small fixes over several drivers, but all are driver-
specific and nothing looks scary. Slightly large changes are seen in
ASoC qcom driver for the bugs that were revealed by the recent ASoC
core change to report the invalid register access errors. Also ASoC
fsl got a slight intensive change for the distortion fix. Others are
only trivial fixes or device-specific quirks.
-----BEGIN PGP SIGNATURE-----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=T8Rb
-----END PGP SIGNATURE-----
Merge tag 'sound-5.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of small fixes over several drivers, but all are driver-
specific and nothing looks scary.
Slightly large changes are seen in ASoC qcom driver for the bugs that
were revealed by the recent ASoC core change to report the invalid
register access errors. Also ASoC fsl got a slight intensive change
for the distortion fix.
Others are only trivial fixes or device-specific quirks"
* tag 'sound-5.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (25 commits)
ALSA: hda: avoid reset of sdo_limit
ALSA: hda/realtek: Add quirk for Samsung Galaxy Book Ion
ALSA: usb-audio: ignore broken processing/extension unit
ASoC: intel: Fix memleak in sst_media_open
ASoC: wm8994: Avoid attempts to read unreadable registers
ASoC: msm8916-wcd-analog: fix register Interrupt offset
ASoC: wm8994: Prevent access to invalid VU register bits on WM1811
ALSA: hda/realtek: Add model alc298-samsung-headphone
ALSA: usb-audio: Update documentation comment for MS2109 quirk
ALSA: isa: fix spelling mistakes in the comments
ALSA: usb-audio: Add capture support for Saffire 6 (USB 1.1)
ALSA: hda/realtek: Add quirk for Samsung Galaxy Flex Book
ASoC: q6routing: add dummy register read/write function
ASoC: q6afe-dai: mark all widgets registers as SND_SOC_NOPM
ASoC: Make soc_component_read() returning an error code again
ASoC: amd: Replacing component->name with codec_dai->name.
ASoC: fsl: Fix unused variable warning
ASoC: tegra: tegra210_i2s: Fix compile warning with CONFIG_PM=n
ASoC: tegra: tegra210_dmic: Fix compile warning with CONFIG_PM=n
ASoC: tegra: tegra210_ahub: Fix compile warning with CONFIG_PM=n
...
Previous improvements around handling device and codec level
probe functionality added the possibility of the voltage level
being undefined for the scenario where the IO voltage retrieved
from the regulator supply was below 1.2V, whereas previously the
code defaulted to the 2.5V to 3.6V range in that case. This
commit restores the default value to avoid this happening.
Fixes: aa5b18d1c2 ("ASoC: da7219: Move soft reset handling to codec level probe")
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Link: https://lore.kernel.org/r/20200821142259.C2ECE3FB96@swsrvapps-01.diasemi.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add version and class information explicitly to prepare for support
for new devices.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200818141435.29205-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It seems the datasheet has never used the word slave for this error
status bit and has always used the term address error. So update the
driver to match the datasheets and also in the process align a bit
better with avoiding the use of such words where possible.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200818160126.4852-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch set reorganises and fixes device and codec level probe/remove
handling within the driver, to allow clean probe and remove at the codec level.
This set relates to an issue raised by Yong Zhi where a codec level re-probe
would fail due to clks still being registered from the previous instantiation.
In addition some improvements around regulator handling and soft reset have
also been included.
Adam Thomson (3):
ASoC: da7219: Move required devm_* allocations to device level code
ASoC: da7219: Move soft reset handling to codec level probe
ASoC: da7219: Fix clock handling around codec level probe
sound/soc/codecs/da7219-aad.c | 85 +++++---
sound/soc/codecs/da7219-aad.h | 3 +
sound/soc/codecs/da7219.c | 493 +++++++++++++++++++++++-------------------
sound/soc/codecs/da7219.h | 1 +
4 files changed, 328 insertions(+), 254 deletions(-)
--
1.9.1
This patch series enables some features on the tlv3204 codec and also fixes some issues faced while testing
v2: Fixed the build error from snd_soc_component_read32
v1: initial ASoC: codec: tlv3204: Codec workaround series
Michael Sit Wei Hong (3):
ASoC: codec: tlv3204: Enable 24 bit audio support
ASoC: codec: tlv3204: Increased maximum supported channels
ASoC: codec: tlv3204: Moving GPIO reset and add ADC reset
sound/soc/codecs/tlv320aic32x4.c | 60 +++++++++++++++++++++++---------
1 file changed, 44 insertions(+), 16 deletions(-)
--
2.17.1
This patch series drops a printk message down to dev_dbg() because it
was noisy and then migrates this driver to use clk_hw based APIs instead
of clk based APIs because this device is a clk provider, not a clk
consumer. I've only lightly tested the last two patches but I don't have
all combinations of clks for this device.
Cc: Cheng-Yi Chiang <cychiang@chromium.org>
Cc: Shuming Fan <shumingf@realtek.com>
Stephen Boyd (3):
ASoC: rt5682: Use dev_dbg() in rt5682_clk_check()
ASoC: rt5682: Drop usage of __clk_get_name()
ASoC: rt5682: Use clk_hw based APIs for registration
sound/soc/codecs/rt5682.c | 73 ++++++++++++---------------------------
sound/soc/codecs/rt5682.h | 2 --
2 files changed, 23 insertions(+), 52 deletions(-)
Based on the last patch to this driver in linux-next.
base-commit: 6301adf942
--
Sent by a computer, using git, on the internet
This allows solutions like ALSA UCM to utilize hardware mono downmix
for cases where mono output to a single speaker is desired only in
specific situations (like on a mobile phone).
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/3662154.EqNIRYjrc8@pliszka
Signed-off-by: Mark Brown <broonie@kernel.org>
Follow recommendation in Documentation/scheduler/completion.rst and
use macro to declare local 'struct completion'
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200813175442.59067-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
"AVDD" is for analog power supply, "DVDD" is for digital power
supply, they can improve the power management.
As the regulator is enabled in pm runtime resume, which is
behind the component driver probe, so accessing registers in
component driver probe will fail. Fix this issue by enabling
regcache_cache_only after pm_runtime_enable.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1597397561-2426-2-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add an binary mixer 'ELD' to each HDMI PCM device so user space
could read the ELD data of external HDMI display.
Signed-off-by: Brent Lu <brent.lu@intel.com>
Link: https://lore.kernel.org/r/20200818004413.12852-1-brent.lu@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Previously the driver would use devm_* related functions at
the codec level probe() to allocate clock resources for MCLK
and the DAI clocks exposed by the device. This caused issues
when registering clocks on a re-probe (no device level
remove/prove involved) as the devm_* resources were never
freed up so the clocks were still registered from the previous
codec level probe().
This commit updates the clock handling for MCLK usage and DAI
clock provision to fix this discrepancy and allow the codec level
probe/remove functionality to operate as intended.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Link: https://lore.kernel.org/r/b92c461baeed27a6cd92e59e36a55c2547218683.1597164865.git.Adam.Thomson.Opensource@diasemi.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As part of the reorganisation of the device level and codec
level probe functionlity, the soft reset handling should really
reside at the codec level and after the instantiation of supplies.
This commit makes the relevant changes to support this change of
scope including the remove of devm_* functions being called for
regulator instantiation at the codec level.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Link: https://lore.kernel.org/r/f7603a4855647429b754ce76f887ec441622015c.1597164865.git.Adam.Thomson.Opensource@diasemi.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Moving GPIO reset to a later stage and before clock registration to
ensure that the host system and codec clocks are in sync. If the host
register clock values prior to gpio reset, the last configured codec clock
is registered to the host. The codec then gets gpio resetted setting the
codec clocks to their default value, causing a mismatch. Host system will
skip clock setting thinking the codec clocks are already at the requested
rate.
ADC reset is added to ensure the next audio capture does not have
undesired artifacts. It is probably related to the original code
where the probe function resets the ADC prior to 1st record.
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Reviewed-by: Sia Jee Heng <jee.heng.sia@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200812094631.4698-4-michael.wei.hong.sit@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Increased maximum supported channel to 8 channels for audio capture
running in TDM mode.
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Reviewed-by: Sia Jee Heng <jee.heng.sia@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200812094631.4698-3-michael.wei.hong.sit@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Enable 24 bit in 32 bit container audio support.
Using the params_physical_width to differentiate
24 bit in 32 bit container and 24 bit in 24 bit container modes.
Use the sample rate, bit depth and channel parameters to
calculate the bit clock needed.
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Reviewed-by: Sia Jee Heng <jee.heng.sia@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200812094631.4698-2-michael.wei.hong.sit@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The (new?) style of clk registration uses clk_hw based APIs so that we
can more easily see the difference between clk providers and clk
consumers. Use the clk_hw based APIs to do this and migrate to devm for
the clkdev creation so that we can reduce the amount of code.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Cc: Cheng-Yi Chiang <cychiang@chromium.org>
Cc: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20200804000531.920688-4-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The __clk_get_name() API is deprecated. Use clk_hw_get_name() or
proper registration techniques to avoid it.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Cc: Cheng-Yi Chiang <cychiang@chromium.org>
Cc: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20200804000531.920688-3-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
I see a spew of "sysclk/dai not set correctly" whenever I cat
/sys/kernel/debug/clk/clk_summary on my device. This is because the
master pointer isn't set yet in this driver. A user isn't going to be
able to do much if this check is failing so this error message isn't
really an error, it's more of a kernel debug message. Lower the priority
to dev_dbg() so that it isn't so noisy.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Cc: Cheng-Yi Chiang <cychiang@chromium.org>
Cc: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20200804000531.920688-2-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver supports WM1811, WM8994, WM8958 devices but according to
documentation and the regmap definitions the WM8958_DSP2_* registers
are only available on WM8958. In current code these registers are
being accessed as if they were available on all the three chips.
When starting playback on WM1811 CODEC multiple errors like:
"wm8994-codec wm8994-codec: ASoC: error at soc_component_read_no_lock on wm8994-codec: -5"
can be seen, which is caused by attempts to read an unavailable
WM8958_DSP2_PROGRAM register. The issue has been uncovered by recent
commit "e2329ee ASoC: soc-component: add soc_component_err()".
This patch adds a check in wm8958_aif_ev() callback so the DSP2 handling
is only done for WM8958.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200731173834.23832-1-s.nawrocki@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For some reason interrupt set and clear register offsets are
not set correctly.
This patch corrects them!
Fixes: 585e881e5b ("ASoC: codecs: Add msm8916-wcd analog codec")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200811103452.20448-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The ADC2 and DAC2 are not available on WM1811 device. This patch moves
the ADC2, DAC2 VU bitfields to a separate array so we can skip accessing
them and avoid unreadable register access on WM1811.
This allows to get rid of warnings during boot like:
wm8994-codec: ASoC: error at soc_component_read_no_lock on wm8994-codec: -5
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Link: https://lore.kernel.org/r/20200804141043.11425-1-s.nawrocki@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This became wide and scattered updates all over the sound tree as
diffstat shows: lots of (still ongoing) refactoring works in ASoC,
fixes and cleanups caught by static analysis, inclusive term
conversions as well as lots of new drivers. Below are highlights:
ASoC core:
* API cleanups and conversions to the unified mute_stream() call
* Simplify I/O helper functions
* Use helper macros to retrieve RTD from substreams
ASoC drivers:
* Lots of fixes and cleanups in Intel ASoC drivers
* Lots of new stuff: Freescale MQS and i.MX6sx, Intel KeemBay I2S,
Maxim MAX98360A and MAX98373 SoundWire, various Mediatek boards,
nVidia Tegra 186 and 210, RealTek RL6231, Samsung Midas and Aries
boards, TI J721e EVM
ALSA core:
* Minor code refacotring for SG-buffer handling
HD-audio:
* Generalization of mute-LED handling with LED classdev
* Intel silent stream support for HDMI
* Device-specific fixes: CA0132, Loongson-3
Others:
* Usual USB- and HD-audio quirks for various devices
* Fixes for echoaudio DMA position handling
* Various documents and trivial fixes for sparse warnings
* Conversion to adapt inclusive terms
-----BEGIN PGP SIGNATURE-----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=sy7n
-----END PGP SIGNATURE-----
Merge tag 'sound-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This became wide and scattered updates all over the sound tree as
diffstat shows: lots of (still ongoing) refactoring works in ASoC,
fixes and cleanups caught by static analysis, inclusive term
conversions as well as lots of new drivers. Below are highlights:
ASoC core:
- API cleanups and conversions to the unified mute_stream() call
- Simplify I/O helper functions
- Use helper macros to retrieve RTD from substreams
ASoC drivers:
- Lots of fixes and cleanups in Intel ASoC drivers
- Lots of new stuff: Freescale MQS and i.MX6sx, Intel KeemBay I2S,
Maxim MAX98360A and MAX98373 SoundWire, various Mediatek boards,
nVidia Tegra 186 and 210, RealTek RL6231, Samsung Midas and Aries
boards, TI J721e EVM
ALSA core:
- Minor code refacotring for SG-buffer handling
HD-audio:
- Generalization of mute-LED handling with LED classdev
- Intel silent stream support for HDMI
- Device-specific fixes: CA0132, Loongson-3
Others:
- Usual USB- and HD-audio quirks for various devices
- Fixes for echoaudio DMA position handling
- Various documents and trivial fixes for sparse warnings
- Conversion to adopt inclusive terms"
* tag 'sound-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (479 commits)
ALSA: pci: delete repeated words in comments
ALSA: isa: delete repeated words in comments
ALSA: hda/tegra: Add 100us dma stop delay
ALSA: hda: Add dma stop delay variable
ASoC: hda/tegra: Set buffer alignment to 128 bytes
ALSA: seq: oss: Serialize ioctls
ALSA: hda/hdmi: Add quirk to force connectivity
ALSA: usb-audio: add startech usb audio dock name
ALSA: usb-audio: Add support for Lenovo ThinkStation P620
Revert "ALSA: hda: call runtime_allow() for all hda controllers"
ALSA: hda/ca0132 - Fix AE-5 microphone selection commands.
ALSA: hda/ca0132 - Add new quirk ID for Recon3D.
ALSA: hda/ca0132 - Fix ZxR Headphone gain control get value.
ALSA: hda/realtek: Add alc269/alc662 pin-tables for Loongson-3 laptops
ALSA: docs: fix typo
ALSA: doc: use correct config variable name
ASoC: core: Two step component registration
ASoC: core: Simplify snd_soc_component_initialize declaration
ASoC: core: Relocate and expose snd_soc_component_initialize
ASoC: sh: Replace 'select' DMADEVICES 'with depends on'
...
Pull crypto updates from Herbert Xu:
"API:
- Add support for allocating transforms on a specific NUMA Node
- Introduce the flag CRYPTO_ALG_ALLOCATES_MEMORY for storage users
Algorithms:
- Drop PMULL based ghash on arm64
- Fixes for building with clang on x86
- Add sha256 helper that does the digest in one go
- Add SP800-56A rev 3 validation checks to dh
Drivers:
- Permit users to specify NUMA node in hisilicon/zip
- Add support for i.MX6 in imx-rngc
- Add sa2ul crypto driver
- Add BA431 hwrng driver
- Add Ingenic JZ4780 and X1000 hwrng driver
- Spread IRQ affinity in inside-secure and marvell/cesa"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (157 commits)
crypto: sa2ul - Fix inconsistent IS_ERR and PTR_ERR
hwrng: core - remove redundant initialization of variable ret
crypto: x86/curve25519 - Remove unused carry variables
crypto: ingenic - Add hardware RNG for Ingenic JZ4780 and X1000
dt-bindings: RNG: Add Ingenic RNG bindings.
crypto: caam/qi2 - add module alias
crypto: caam - add more RNG hw error codes
crypto: caam/jr - remove incorrect reference to caam_jr_register()
crypto: caam - silence .setkey in case of bad key length
crypto: caam/qi2 - create ahash shared descriptors only once
crypto: caam/qi2 - fix error reporting for caam_hash_alloc
crypto: caam - remove deadcode on 32-bit platforms
crypto: ccp - use generic power management
crypto: xts - Replace memcpy() invocation with simple assignment
crypto: marvell/cesa - irq balance
crypto: inside-secure - irq balance
crypto: ecc - SP800-56A rev 3 local public key validation
crypto: dh - SP800-56A rev 3 local public key validation
crypto: dh - check validity of Z before export
lib/mpi: Add mpi_sub_ui()
...
Removing ADDITIONAL_CONTROL_4 from the list of readable registers cause
audio distortion.
This change was sent as a comment below the --- line when submitting
commit 658bb297e3 ("ASoC: wm8962: Do not access WM8962_GPIO_BASE"), so
it was not supposed to get merged.
Keep WM8962_ADDITIONAL_CONTROL_4 inside wm8962_readable_register() to
fix the regression.
Fixes: 658bb297e3 ("ASoC: wm8962: Do not access WM8962_GPIO_BASE")
Reported-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20200803115233.19034-1-festevam@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the WM8962 datasheet, there is no register at address 0x200.
WM8962_GPIO_BASE is just a base address for the GPIO registers and not a
real register, so remove it from wm8962_readable_register().
Also, Register 515 (WM8962_GPIO_BASE + 3) does not exist, so skip
its access.
This fixes the following errors:
wm8962 0-001a: ASoC: error at soc_component_read_no_lock on wm8962.0-001a: -16
wm8962 0-001a: ASoC: error at soc_component_read_no_lock on wm8962.0-001a: -16
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200717135959.19212-1-festevam@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Reset the device before programming the registers or all programming
will be lost as the device resets registers to default settings.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200730142419.28205-2-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The header was updated to align with the data sheet to start the GPO_CFG
at GPO_CFG0. The code was not updated to the change and therefore the
GPO_CFG0 register was not written to.
Fixes: 6617cff6a0 ("ASoC: tlv320adcx140: Add GPO configuration and drive output config")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200730142419.28205-1-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add General Purpose Output (GPO) configuration and driver output
configuration. The GPOs can be configured as a GPO, IRQ, SDOUT or a
PDMCLK output. In addition the output drive can be configured with
various configurations.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200728160833.24130-2-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix white space issues and remove else case where it was not needed.
Convert "static const char *" to "static const char * const"
Fixes: 689c7655b5 ("ASoC: tlv320adcx140: Add the tlv320adcx140 codec driver family")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200728164339.16841-1-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Update the shutdown GPIO property to be shutdown from shut-down.
Fixes: c173dba44c ("ASoC: tas2562: Introduce the TAS2562 amplifier")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200723160838.9738-2-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Modify dsm_init sequence and dsm param bin check condition.
- Move dsm_init() to after amp init setting to
make sure dsm init is last setting.
- dsm param bin check condition changed for extended register setting.
Signed-off-by: Steve Lee <steves.lee@maximintegrated.com>
Link: https://lore.kernel.org/r/20200724060149.19261-1-steves.lee@maximintegrated.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Global EN register guide to off before AMP_EN register
when amp disable sequence.
- remove AMP_EN control before max98390_dac_event call
Signed-off-by: Steve Lee <steves.lee@maximintegrated.com>
Link: https://lore.kernel.org/r/20200724060058.19201-1-steves.lee@maximintegrated.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Coefficient files now support additional metadata blocks, these
contain machine parsable text strings describing the parameters
contained in the coefficient file.
Signed-off-by: James Schulman <james.schulman@cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200723110321.16382-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 5bd70440cb ("ASoC: soc-dai: revert all changes to DAI
startup/shutdown sequence"), introduced a slight change of semantics
to DAI startup/shutdown. If startup() returns an error, shutdown()
is now called for the DAI.
This causes a deadlock in hdac_hda which issues a call to
snd_hda_codec_pcm_put() in case open fails. Upon error, soc_pcm_open()
will call shutdown(), and pcm_put() ends up getting called twice. Result
is a deadlock on pcm->open_mutex, as snd_device_free() gets called from
within snd_pcm_open(). Typical task backtrace looks like this:
[ 334.244627] snd_pcm_dev_disconnect+0x49/0x340 [snd_pcm]
[ 334.244634] __snd_device_disconnect.part.0+0x2c/0x50 [snd]
[ 334.244640] __snd_device_free+0x7f/0xc0 [snd]
[ 334.244650] snd_hda_codec_pcm_put+0x87/0x120 [snd_hda_codec]
[ 334.244660] soc_pcm_open+0x6a0/0xbe0 [snd_soc_core]
[ 334.244676] ? dpcm_add_paths.isra.0+0x491/0x590 [snd_soc_core]
[ 334.244679] ? kfree+0x9a/0x230
[ 334.244686] dpcm_be_dai_startup+0x255/0x300 [snd_soc_core]
[ 334.244695] dpcm_fe_dai_open+0x20e/0xf30 [snd_soc_core]
[ 334.244701] ? snd_pcm_hw_rule_muldivk+0x110/0x110 [snd_pcm]
[ 334.244709] ? dpcm_be_dai_startup+0x300/0x300 [snd_soc_core]
[ 334.244714] ? snd_pcm_attach_substream+0x3c4/0x540 [snd_pcm]
[ 334.244719] snd_pcm_open_substream+0x69a/0xb60 [snd_pcm]
[ 334.244729] ? snd_pcm_release_substream+0x30/0x30 [snd_pcm]
[ 334.244732] ? __mutex_lock_slowpath+0x10/0x10
[ 334.244736] snd_pcm_open+0x1b3/0x3c0 [snd_pcm]
Fixes: 5bd70440cb ("ASoC: soc-dai: revert all changes to DAI startup/shutdown sequence")
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
BugLink: https://github.com/thesofproject/linux/issues/2159
Link: https://lore.kernel.org/r/20200717101950.3885187-3-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The hdac_hda remove implementation fails to free the hda codec
resources, leading to memleaks at module unload. This gap has been there
from the start, commit 6bae5ea949 ("ASoC: hdac_hda: add asoc
extension for legacy HDA codec drivers").
Instead of duplicating the cleanup logic, use the common
snd_hda_codec_cleanup_for_unbind() to free the resources. Remove
existing code in hdac_hda to cleanup "codec.jackpoll_work" and call to
snd_hdac_regmap_exit(), as these are already done in
snd_hda_codec_cleanup_for_unbind().
The cleanup is done in ASoC component remove() callback and not in the
HDAC bus hdev_detach(). This is done to ensure the codec specific
cleanup routines are run before the parent card is freed.
Fixes: 6bae5ea949 ("ASoC: hdac_hda: add asoc extension for legacy HDA codec drivers")
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
BugLink: https://github.com/thesofproject/linux/issues/2195
Link: https://lore.kernel.org/r/20200717101950.3885187-2-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add error handling for patch_ops in hdac_hda_codec_probe().
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20200717101950.3885187-1-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200719153822.59788-1-grandmaster@al2klimov.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the reset property name when allocating the GPIO descriptor.
The gpiod_get_optional appends either the -gpio or -gpios suffix to the
name.
Fixes: 1a476abc72 ("tas2770: add tas2770 smart PA kernel driver")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200720181202.31000-2-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Partially reverts commit 128f825aea ("ASoC: max98357a: move control
of SD_MODE to DAPM").
In order to have mute control of max98357 from machine drivers, commit
128f825aea ("ASoC: max98357a: move control of SD_MODE to DAPM")
moves the control of SD_MODE from DAI ops to DAPM events. However, pop
noise has been observed on rk3399-gru-kevin boards due to this commit.
The commit 128f825aea caused sequence of DAI clocks and SD_MODE
changed on rk3399-gru-kevin boards.
With the commit 128f825aea:
- SD_MODE will be set to 1 before DAI clocks start.
- SD_MODE will be set to 0 after DAI clocks stop.
As a result, pop noise.
Moves the control of SD_MODE back to DAI ops. In the meantime, uses an
additional flag in DAPM event to provide chance of mute control for
machine drivers.
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Tested-By: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Link: https://lore.kernel.org/r/20200721114232.2812254-1-tzungbi@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
An awful lot of mostly small fixes here, mainly for x86 based platforms
and the CODEC drivers mainly used on them. For the most part this is
either minor device specific stuff which seems to come from detailed
testing or robustness against errors which comes from people having done
some fuzzing runs aginst the topology code.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl8Rzk0THGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0GWlB/9Y6g9MQ4Ih4Evsv4q/ZeJRnTGaKZMT
7XjZRB64tTrFWbt38iGpRcjQLy5I5tVuGbdd7mPVKgZgSVxvoj4HQ4vf23rkNxon
RuQIbFtI2rwvdWKDo9a0RkF+IwuWhmrupfN8DMZoJIyRyh99tDrLwGjmiUUXsVV2
NyfcGerQjbngraK+2lQtnzbfX9d2qGiZVKEdczQVjJcgyNAYI2N22+3O1hFHmo80
6f5BbRpaVPXpQmRBmFthTdgthrr6uZPDXDoEYw77V9okvCwthrjBIGDow4EkVTZk
xRPKo7g2EFuLd18ro/J8nAJ1KDideKB4I5cFcz9QViVZbVftk2CrFrvg
=V/55
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v5.8-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.8
An awful lot of mostly small fixes here, mainly for x86 based platforms
and the CODEC drivers mainly used on them. For the most part this is
either minor device specific stuff which seems to come from detailed
testing or robustness against errors which comes from people having done
some fuzzing runs aginst the topology code.
Some settings should set to default value after the calibration.
This patch also disables the 25MHz and 1MHz clock power when the jack unplugged.
The JD is triggered by JDH, therefore this patch removes JDL setting.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20200717070228.28660-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The pin status of the widget was connected after the sound card registered.
The rt5682_headset_detect function will use the pin status of these two widgets
to decide the certain register setting on/off.
Therefore this patch disables the pin of these two widgets in the codec probe.
This patch could avoid the misjudgment.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20200717070256.28712-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_dai_digital_mute() is internally using both
mute_stream() (1) or digital_mute() (2), but the difference between
these 2 are only handling direction.
We can merge digital_mute() into mute_stream
int snd_soc_dai_digital_mute(xxx, int direction)
{
...
else if (dai->driver->ops->mute_stream)
(1) return dai->driver->ops->mute_stream(xxx, direction);
else if (direction == SNDRV_PCM_STREAM_PLAYBACK &&
dai->driver->ops->digital_mute)
(2) return dai->driver->ops->digital_mute(xxx);
...
}
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/87pn95wiwa.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_dai_digital_mute() is internally using both
mute_stream() (1) or digital_mute() (2), but the difference between
these 2 are only handling direction.
We can merge digital_mute() into mute_stream
int snd_soc_dai_digital_mute(xxx, int direction)
{
...
else if (dai->driver->ops->mute_stream)
(1) return dai->driver->ops->mute_stream(xxx, direction);
else if (direction == SNDRV_PCM_STREAM_PLAYBACK &&
dai->driver->ops->digital_mute)
(2) return dai->driver->ops->digital_mute(xxx);
...
}
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/87r1tlwiwe.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_dai_digital_mute() is internally using both
mute_stream() (1) or digital_mute() (2), but the difference between
these 2 are only handling direction.
We can merge digital_mute() into mute_stream
int snd_soc_dai_digital_mute(xxx, int direction)
{
...
else if (dai->driver->ops->mute_stream)
(1) return dai->driver->ops->mute_stream(xxx, direction);
else if (direction == SNDRV_PCM_STREAM_PLAYBACK &&
dai->driver->ops->digital_mute)
(2) return dai->driver->ops->digital_mute(xxx);
...
}
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Link: https://lore.kernel.org/r/87sge1wiwi.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_dai_digital_mute() is internally using both
mute_stream() (1) or digital_mute() (2), but the difference between
these 2 are only handling direction.
We can merge digital_mute() into mute_stream
int snd_soc_dai_digital_mute(xxx, int direction)
{
...
else if (dai->driver->ops->mute_stream)
(1) return dai->driver->ops->mute_stream(xxx, direction);
else if (direction == SNDRV_PCM_STREAM_PLAYBACK &&
dai->driver->ops->digital_mute)
(2) return dai->driver->ops->digital_mute(xxx);
...
}
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/87tuyhwiwm.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_dai_digital_mute() is internally using both
mute_stream() (1) or digital_mute() (2), but the difference between
these 2 are only handling direction.
We can merge digital_mute() into mute_stream
int snd_soc_dai_digital_mute(xxx, int direction)
{
...
else if (dai->driver->ops->mute_stream)
(1) return dai->driver->ops->mute_stream(xxx, direction);
else if (direction == SNDRV_PCM_STREAM_PLAYBACK &&
dai->driver->ops->digital_mute)
(2) return dai->driver->ops->digital_mute(xxx);
...
}
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/87v9ixwiwr.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_dai_digital_mute() is internally using both
mute_stream() (1) or digital_mute() (2), but the difference between
these 2 are only handling direction.
We can merge digital_mute() into mute_stream
int snd_soc_dai_digital_mute(xxx, int direction)
{
...
else if (dai->driver->ops->mute_stream)
(1) return dai->driver->ops->mute_stream(xxx, direction);
else if (direction == SNDRV_PCM_STREAM_PLAYBACK &&
dai->driver->ops->digital_mute)
(2) return dai->driver->ops->digital_mute(xxx);
...
}
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/87wo3dwiwv.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_dai_digital_mute() is internally using both
mute_stream() (1) or digital_mute() (2), but the difference between
these 2 are only handling direction.
We can merge digital_mute() into mute_stream
int snd_soc_dai_digital_mute(xxx, int direction)
{
...
else if (dai->driver->ops->mute_stream)
(1) return dai->driver->ops->mute_stream(xxx, direction);
else if (direction == SNDRV_PCM_STREAM_PLAYBACK &&
dai->driver->ops->digital_mute)
(2) return dai->driver->ops->digital_mute(xxx);
...
}
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/87y2ntwix0.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_dai_digital_mute() is internally using both
mute_stream() (1) or digital_mute() (2), but the difference between
these 2 are only handling direction.
We can merge digital_mute() into mute_stream
int snd_soc_dai_digital_mute(xxx, int direction)
{
...
else if (dai->driver->ops->mute_stream)
(1) return dai->driver->ops->mute_stream(xxx, direction);
else if (direction == SNDRV_PCM_STREAM_PLAYBACK &&
dai->driver->ops->digital_mute)
(2) return dai->driver->ops->digital_mute(xxx);
...
}
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/87zh89wix5.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_dai_digital_mute() is internally using both
mute_stream() (1) or digital_mute() (2), but the difference between
these 2 are only handling direction.
We can merge digital_mute() into mute_stream
int snd_soc_dai_digital_mute(xxx, int direction)
{
...
else if (dai->driver->ops->mute_stream)
(1) return dai->driver->ops->mute_stream(xxx, direction);
else if (direction == SNDRV_PCM_STREAM_PLAYBACK &&
dai->driver->ops->digital_mute)
(2) return dai->driver->ops->digital_mute(xxx);
...
}
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/871rllxxhp.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_dai_digital_mute() is internally using both
mute_stream() (1) or digital_mute() (2), but the difference between
these 2 are only handling direction.
We can merge digital_mute() into mute_stream
int snd_soc_dai_digital_mute(xxx, int direction)
{
...
else if (dai->driver->ops->mute_stream)
(1) return dai->driver->ops->mute_stream(xxx, direction);
else if (direction == SNDRV_PCM_STREAM_PLAYBACK &&
dai->driver->ops->digital_mute)
(2) return dai->driver->ops->digital_mute(xxx);
...
}
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/873661xxhu.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_dai_digital_mute() is internally using both
mute_stream() (1) or digital_mute() (2), but the difference between
these 2 are only handling direction.
We can merge digital_mute() into mute_stream
int snd_soc_dai_digital_mute(xxx, int direction)
{
...
else if (dai->driver->ops->mute_stream)
(1) return dai->driver->ops->mute_stream(xxx, direction);
else if (direction == SNDRV_PCM_STREAM_PLAYBACK &&
dai->driver->ops->digital_mute)
(2) return dai->driver->ops->digital_mute(xxx);
...
}
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/874kqhxxhz.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_dai_digital_mute() is internally using both
mute_stream() (1) or digital_mute() (2), but the difference between
these 2 are only handling direction.
We can merge digital_mute() into mute_stream
int snd_soc_dai_digital_mute(xxx, int direction)
{
...
else if (dai->driver->ops->mute_stream)
(1) return dai->driver->ops->mute_stream(xxx, direction);
else if (direction == SNDRV_PCM_STREAM_PLAYBACK &&
dai->driver->ops->digital_mute)
(2) return dai->driver->ops->digital_mute(xxx);
...
}
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/875zaxxxi4.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
