Print useful information not only dual-role mode but also
device mode and host mode.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check the return value of devm_extcon_register_notifier() and
add error handling.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 2f31a67f01 ("usb: xhci: Prevent bus suspend if a port connect
change or polling state is detected") was intended to prevent ports that
were still link training from being forced to U3 suspend state mid
enumeration.
This solved enumeration issues for devices with slow link training.
Turns out some devices are stuck in the link training/polling state,
and thus that patch will prevent suspend completely for these devices.
This is seen with USB3 card readers in some MacBooks.
Instead of preventing suspend, give some time to complete the link
training. On successful training the port will end up as connected
and enabled.
If port instead is stuck in link training the bus suspend will continue
suspending after 360ms (10 * 36ms) timeout (tPollingLFPSTimeout).
Original patch was sent to stable, this one should go there as well
Fixes: 2f31a67f01 ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xhci debug capability (DbC) feature did its memory cleanup with
spinlock held. dma_free_coherent() warns if called with interrupts
disabled
move the memory cleanup outside the spinlock
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A suspended SS port in U3 link state will go to U0 when resumed, but
can almost immediately after that enter U1 or U2 link power save
states before host controller driver reads the port status.
Host controller driver only checks for U0 state, and might miss
the finished resume, leaving flags unclear and skip notifying usb
code of the wake.
Add U1 and U2 to the possible link states when checking for finished
port resume.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The write_parport_reg_nonblock() helper takes a reference to the struct
mos_parport, but failed to release it in a couple of error paths after
allocation failures, leading to a memory leak.
Johan said that move the kref_get() and mos_parport assignment to the
end of urbtrack initialisation is a better way, so move it. and
mos_parport do not used until urbtrack initialisation.
Signed-off-by: Lin Yi <teroincn@163.com>
Fixes: b69578df7e ("USB: usbserial: mos7720: add support for parallel port on moschip 7715")
Cc: stable <stable@vger.kernel.org> # 2.6.35
Signed-off-by: Johan Hovold <johan@kernel.org>
In order to be able to request an array of reset controls in acquired or
released mode, add the acquired flag to of_reset_control_array_get() and
pass the flag to subsequent calls of __of_reset_control_get().
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
In f_hidg_write() the write_spinlock is acquired before calling
usb_ep_queue() which causes a deadlock when dummy_hcd is being used.
This is because dummy_queue() callbacks into f_hidg_req_complete() which
tries to acquire the same spinlock. This is (part of) the backtrace when
the deadlock occurs:
0xffffffffc06b1410 in f_hidg_req_complete
0xffffffffc06a590a in usb_gadget_giveback_request
0xffffffffc06cfff2 in dummy_queue
0xffffffffc06a4b96 in usb_ep_queue
0xffffffffc06b1eb6 in f_hidg_write
0xffffffff8127730b in __vfs_write
0xffffffff812774d1 in vfs_write
0xffffffff81277725 in SYSC_write
Fix this by releasing the write_spinlock before calling usb_ep_queue()
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: stable@vger.kernel.org # 4.11+
Fixes: 749494b6bd ("usb: gadget: f_hid: fix: Move IN request allocation to set_alt()")
Signed-off-by: Radoslav Gerganov <rgerganov@vmware.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Restore the status of ep->stopped in function net2272_dequeue().
When the given request is not found in the endpoint queue
the function returns -EINVAL without restoring the state of
ep->stopped. Thus the endpoint keeps blocked and does not transfer
any data anymore.
This fix is only compile-tested, since we do not have a
corresponding hardware. An analogous fix was tested in the sibling
driver. See "usb: gadget: net2280: Fix net2280_dequeue()"
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When a request must be dequeued with net2280_dequeue() e.g. due
to a device clear action and the same request is finished by the
function scan_dma_completions() then the function net2280_dequeue()
does not find the request in the following search loop and
returns the error -EINVAL without restoring the status ep->stopped.
Thus the endpoint keeps blocked and does not receive any data
anymore.
This fix restores the status and does not issue an error message.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The OUT endpoint normally blocks (NAK) subsequent packets when a
short packet was received and returns an incomplete queue entry to
the gadget driver. Thereby the gadget driver can detect a short packet
when reading queue entries with a length that is not equal to a
multiple of packet size.
The start_queue() function enables receiving OUT packets regardless of
the content of the OUT FIFO. This results in a race: With the current
code, it's possible that the "!ep->is_in && (readl(&ep->regs->ep_stat)
& BIT(NAK_OUT_PACKETS))" test in start_dma() will fail, then a short
packet will be received, and then start_queue() will call
stop_out_naking(). That's what we don't want (OUT naking gets turned
off while there is data in the FIFO) because then the next driver
request might receive a mixture of old and new packets.
With the patch, this race can't occur because the FIFO's state is
tested after we know that OUT naking is already turned on, and OUT
naking is stopped only when both of the conditions are met. This
ensures that all received data is delivered to the gadget driver,
which can detect a short packet now before new packets are appended
to the last short packet.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There is no need to compare *port* with >= 0 because such comparison
of an unsigned value is always true.
Fix this by removing such comparison.
Addresses-Coverity-ID: 1443949 ("Unsigned compared against 0")
Fixes: 02a50b8750 ("usb: usb251xb: add usb data lane port swap feature")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add __printf attribute to fusb302_log function, so that we get
compiler warnings when specifying wrong vararg parameters.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the code which avoids doing i2c-transfers while our parent
i2c-adapter may be suspended by busy-waiting for our resume handler
to be called.
Instead move the interrupt handling from a threaded interrupt handler
to a work-queue and install a non-threaded interrupt handler which
normally queues the new interrupt handling work directly.
When our suspend handler gets called we set a flag which makes the new
non-threaded interrupt handler skip queueing the work before our parent
i2c-adapter is ready, instead the new non-threaded handler will record an
interrupt has happened during suspend and then our resume handler will
queue the work (at which point our parent will be ready).
Note normally i2c drivers solve the problem of not being able to access
the i2c bus until the i2c-controller is resumed by simply disabling their
irq from the suspend handler and re-enabling it on resume.
That is not possible with the fusb302 since the irq is a wakeup source
(it must be a wakeup source so that we can do PD negotiation when a
charger gets plugged in while suspended).
Besides avoiding the ugly busy-wait, this also fixes the following errors
which were logged by the busy-wait code when woken from suspend by plugging
in a Type-C device:
fusb302: i2c: pm suspend, retry 1 / 10
fusb302: i2c: pm suspend, retry 2 / 10
etc.
This commit also changes the devm_request_irq to a regular request_irq
+ free_irq, so that the work can be properly stopped. While at it also
properly disable the wake setting on the irq and also properly stop the
delayed work for bcl handling.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a copy and paste error in an error message and a spelling error
in a comment.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The FUSB302 will stop toggling with a FUSB_REG_STATUS1A_TOGSS_SRC? status,
as soon as it sees either Ra or Rd on a CC pin.
Before this commit fusb302_handle_togdone_src would assume that the toggle-
engine always stopped at the CC pin indicating the polarity, IOW it assumed
that it stopped at the pin connected to Rd. It did check the CC-status of
that pin, but it did not expect to get a CC-status of Ra and therefore
treated this as CC-open. This lead to the following 2 problems:
1) If a powered cable/adapter gets plugged in with Ra on CC1 and Rd on CC2
then 4 of 5 times when plugged in toggling will stop with a togdone_result
of FUSB_REG_STATUS1A_TOGSS_SRC1. 3/5th of the time the toggle-engine is
testing for being connected as a sink and after that it tests 1/5th of the
time for connected as a src through CC1 before finally testing the last
1/5th of the time for being a src connected through CC2.
This was a problem because we would only check the CC pin status for the
pin on which the toggling stopped which in this polarity 4 out of 5
times would be the Ra pin. The code before this commit would treat Ra as
CC-open and then restart toggling. Once toggling is restarted we are
guaranteed to end with FUSB_REG_STATUS1A_TOGSS_SRC1 as CC1 is tested first,
leading to a CC-status of Ra again and an infinite restart toggling loop.
So 4 out of 5 times when plugged in in this polarity a powered adapter
will not work.
2) Even if we happen to have the right polarity or 1/5th of the time in
the polarity with problem 1), we would report the non Rd pin as CC-open
rather then as Ra, resulting in the tcpm.c code not enabling Vconn which
is a problem for some adapters.
This commit fixes this by getting the CC-status of *both* pins and then
determining the polarity based on that, rather then on where the toggling
stopped.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The datasheet says the vconn MUST be off when we start toggling. The
tcpm.c state-machine is responsible to make sure vconn is off, but lets
add a WARN to catch any cases where vconn is not off for some reason.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the recent cleanups, tcpm_set_cc is the only caller of
fusb302_set_cc_pull, fold fusb302_set_cc_pull directly into
tcpm_set_cc for a nice cleanup.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit ea3b4d5523 ("usb: typec: fusb302: Resolve fixed power role
contract setup"), tcpm_set_cc always calls fusb302_set_toggling.
Before this refactor tcpm_set_cc does the following:
1) fusb302_set_toggling(TOGGLING_MODE_OFF),
this sets both FUSB_REG_MASK_BC_LVL and FUSB_REG_MASK_COMP_CHNG.
2) fusb302_set_cc_pull(...).
3) "reset cc status".
4) if pull-up fusb302_set_src_current(...).
5) if pull-up or pull-down enable bc-lvl resp comp-chng irq.
6) fusb302_set_toggling(new-toggling-mode), which again
sets both FUSB_REG_MASK_BC_LVL and FUSB_REG_MASK_COMP_CHNG disabling
the just enabled irq. fusb302_set_toggling is skipped when the new
toggling mode is TOGGLING_MODE_OFF because this is already done in 1,
note in this case 5) is a no-op.
When we are toggling the bits set by fusb302_set_cc_pull will be ignored
until we turn toggling off, so we can safely move the fusb302_set_cc_pull
call to before setting TOGGLING_MODE_OFF.
Either we are not toggling yet, or the src-current has already been set,
so we can also safely set the src-current earlier, allowing us to do the
fusb302_set_toggling(TOGGLING_MODE_OFF) call at the same time as we
set the other toggling modes. Also setting the src-current is a no-op
when not enabling pull-ups, so we can drop the if.
And since the second fusb302_set_toggling undoes the effects of step 5,
we can skip step 5, the bc-lvl resp comp-chng irq wil be enabled by
fusb302_handle_togdone_snk resp. fusb302_handle_togdone_src when toggling
is done.
Together this allows us to simplify things to:
1) fusb302_set_cc_pull(...)
2) "reset cc status"
3) fusb302_set_src_current(...)
4) fusb302_set_toggling(new-toggling-mode)
This commit does this, leading to a nice cleanup.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 2 callers of fusb302_set_cc_polarity both call fusb302_set_cc_pull
directly before calling fusb302_set_cc_polarity, this is not ideal for
2 reasons:
1) fusb302_set_cc_pull uses the cached polarity when applying the pull-ups,
which maybe changed immediately afterwards, to fix this set_cc_polarity
already does the pull-up setting.
2) Both touch the SWITCHES0 register in a r-w-modify cycle, this leads to
read reg, write reg, read reg, write reg. If we fold the setting of
the pull-downs into fusb302_set_cc_polarity then not only can we avoid
doing the reads / writes twice, at this point we set all bits, so we
can skip the read, turning 4 (slowish) i2c-transfers into 1.
Doing this also avoids the need to cache the pull_up state in
struct fusb302_chip.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Keep the orientation value when setting the mux to safe mode, this
fixes the orientation getting reset when switching alt-modes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If our port-partner supports both DP-only operation (pin-assignment C)
and multi-func operation (pin-assignment D) and we only support
pin-assignment D and the port-partner prefers DP-only mode, then
before this commit we would and up masking out pin-assignment D from
the available pin-assignments and fail to pick a pin-assignment.
Instead only mask out the multi-func pin-assignments if we support
dp-only pin-assignments, so that we correctly fall-back to a multi-func
pin-assignment in this case (by picking pin-assignment D).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"vdev" points to vhci_hcd->vdev[] array and vhci_hcd->vdev[] array
is not a pointer array but a structure array and it is already used
in vhci_urb_enqueue() and then passed to vhci_tx_urb() as an argument.
vhci_tx_urb() is not called except vhci_urb_enqueue(). So, "vdev"
can not be null pointer. This null check statement is meaningless.
Signed-off-by: Suwan Kim <suwan.kim027@gmail.com>
Acked-by: Shuah Khan <shuah@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are cases where multiple device tree nodes point to the
same phy node by means of the "phys" property, but we should
only consider those nodes that are marked as available rather
than just any node.
Fixes: 98bfb39466 ("usb: of: add an api to get dr_mode by the phy node")
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PD 2.0 sinks are supposed to accept src-capabilities with a 3.0 header and
simply ignore any src PDOs which the sink does not understand such as PPS
but some 2.0 sinks instead ignore the entire PD_DATA_SOURCE_CAP message,
causing contract negotiation to fail.
This commit fixes such sinks not working by re-trying the contract
negotiation with PD-2.0 source-caps messages if we don't have a contract
after PD_N_HARD_RESET_COUNT hard-reset attempts.
The problem fixed by this commit was noticed with a Type-C to VGA dongle.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently there is no check on platform_get_irq() return value
in case it fails, hence never actually reporting any errors and
causing unexpected behavior when using such value as argument
for function regmap_irq_get_virq().
Fix this by adding a proper check, a message error and return
*irq* in case platform_get_irq() fails.
Addresses-Coverity-ID: 1443899 ("Improper use of negative value")
Fixes: d2061f9cc3 ("usb: typec: add driver for Intel Whiskey Cove PMIC USB Type-C PHY")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SIMCom SIM5218 and compatible devices have 5 USB interfaces, only 4
of which are serial ports. The fifth is a network interface supported
by the qmi-wwan driver. Furthermore, the serial ports do not support
modem control signals. Add driver_info flags to reflect this.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Fixes: ec0cd94d88 ("usb: option: add SIMCom SIM5218")
Cc: stable <stable@vger.kernel.org> # 3.2
Signed-off-by: Johan Hovold <johan@kernel.org>
Add PIDs for the NovaTech OrionLX+ and Orion I/O so they can be
automatically detected.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The Quectel EM12 is a Cat. 12 LTE modem. It behaves in the exactly the
same way as the EP06 (including the dynamic configuration behavior), so
the same checks on reserved interfaces, etc. are needed.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
As all the memblock allocation functions return NULL in case of error
rather than panic(), the duplicates with _nopanic suffix can be removed.
Link: http://lkml.kernel.org/r/1548057848-15136-22-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Petr Mladek <pmladek@suse.com> [printk]
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Dennis Zhou <dennis@kernel.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Guo Ren <ren_guo@c-sky.com> [c-sky]
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Juergen Gross <jgross@suse.com> [Xen]
Cc: Mark Salter <msalter@redhat.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- add debugfs support for dumping dma-debug information (Corentin Labbe)
- Kconfig cleanups (Andy Shevchenko and me)
- debugfs cleanups (Greg Kroah-Hartman)
- improve dma_map_resource and use it in the media code
- arch_setup_dma_ops / arch_teardown_dma_ops cleanups
- various small cleanups and improvements for the per-device coherent
allocator
- make the DMA mask an upper bound and don't fail "too large" dma mask
in the remaning two architectures - this will allow big driver
cleanups in the following merge windows
-----BEGIN PGP SIGNATURE-----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=nAMI
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-5.1' of git://git.infradead.org/users/hch/dma-mapping
Pull DMA mapping updates from Christoph Hellwig:
- add debugfs support for dumping dma-debug information (Corentin
Labbe)
- Kconfig cleanups (Andy Shevchenko and me)
- debugfs cleanups (Greg Kroah-Hartman)
- improve dma_map_resource and use it in the media code
- arch_setup_dma_ops / arch_teardown_dma_ops cleanups
- various small cleanups and improvements for the per-device coherent
allocator
- make the DMA mask an upper bound and don't fail "too large" dma mask
in the remaning two architectures - this will allow big driver
cleanups in the following merge windows
* tag 'dma-mapping-5.1' of git://git.infradead.org/users/hch/dma-mapping: (21 commits)
Documentation/DMA-API-HOWTO: update dma_mask sections
sparc64/pci_sun4v: allow large DMA masks
sparc64/iommu: allow large DMA masks
sparc64: refactor the ali DMA quirk
ccio: allow large DMA masks
dma-mapping: remove the DMA_MEMORY_EXCLUSIVE flag
dma-mapping: remove dma_mark_declared_memory_occupied
dma-mapping: move CONFIG_DMA_CMA to kernel/dma/Kconfig
dma-mapping: improve selection of dma_declare_coherent availability
dma-mapping: remove an incorrect __iommem annotation
of: select OF_RESERVED_MEM automatically
device.h: dma_mem is only needed for HAVE_GENERIC_DMA_COHERENT
mfd/sm501: depend on HAS_DMA
dma-mapping: add a kconfig symbol for arch_teardown_dma_ops availability
dma-mapping: add a kconfig symbol for arch_setup_dma_ops availability
dma-mapping: move debug configuration options to kernel/dma
dma-debug: add dumping facility via debugfs
dma: debug: no need to check return value of debugfs_create functions
videobuf2: replace a layering violation with dma_map_resource
dma-mapping: don't BUG when calling dma_map_resource on RAM
...
This is mostly update of the usual drivers: arcmsr, qla2xxx, lpfc,
hisi_sas, target/iscsi and target/core. Additionally Christoph
refactored gdth as part of the dma changes. The major mid-layer
change this time is the removal of bidi commands and with them the
whole of the osd/exofs driver and filesystem.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXIC54SYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishT1GAPwJEV23
ExPiPsnuVgKj49nLTagZ3rILRQcYNbL+MNYqxQEA0cT8FHzSDBfWY5OKPNE+RQ8z
f69LpXGmMpuagKGvvd4=
=Fhy1
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: arcmsr, qla2xxx, lpfc,
hisi_sas, target/iscsi and target/core.
Additionally Christoph refactored gdth as part of the dma changes. The
major mid-layer change this time is the removal of bidi commands and
with them the whole of the osd/exofs driver and filesystem. This is a
major simplification for block and mq in particular"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (240 commits)
scsi: cxgb4i: validate tcp sequence number only if chip version <= T5
scsi: cxgb4i: get pf number from lldi->pf
scsi: core: replace GFP_ATOMIC with GFP_KERNEL in scsi_scan.c
scsi: mpt3sas: Add missing breaks in switch statements
scsi: aacraid: Fix missing break in switch statement
scsi: kill command serial number
scsi: csiostor: drop serial_number usage
scsi: mvumi: use request tag instead of serial_number
scsi: dpt_i2o: remove serial number usage
scsi: st: osst: Remove negative constant left-shifts
scsi: ufs-bsg: Allow reading descriptors
scsi: ufs: Allow reading descriptor via raw upiu
scsi: ufs-bsg: Change the calling convention for write descriptor
scsi: ufs: Remove unused device quirks
Revert "scsi: ufs: disable vccq if it's not needed by UFS device"
scsi: megaraid_sas: Remove a bunch of set but not used variables
scsi: clean obsolete return values of eh_timed_out
scsi: sd: Optimal I/O size should be a multiple of physical block size
scsi: MAINTAINERS: SCSI initiator and target tweaks
scsi: fcoe: make use of fip_mode enum complete
...
-----BEGIN PGP SIGNATURE-----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=vf9L
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Use match_string() instead of reimplementing it (Andy Shevchenko)
- Enable SERR# forwarding for all bridges (Bharat Kumar Gogada)
- Use Latency Tolerance Reporting if already enabled by platform (Bjorn
Helgaas)
- Save/restore LTR info for suspend/resume (Bjorn Helgaas)
- Fix DPC use of uninitialized data (Dongdong Liu)
- Probe bridge window attributes only once at enumeration-time to fix
device accesses during rescan (Bjorn Helgaas)
- Return BAR size (not "size -1 ") from pci_size() to simplify code (Du
Changbin)
- Use config header type (not class code) identify bridges more
reliably (Honghui Zhang)
- Work around Intel Denverton incorrect Trace Hub BAR size reporting
(Alexander Shishkin)
- Reorder pciehp cached state/hardware state updates to avoid missed
interrupts (Mika Westerberg)
- Turn ibmphp semaphores into completions or mutexes (Arnd Bergmann)
- Mark expected switch fall-through (Mathieu Malaterre)
- Use of_node_name_eq() for node name comparisons (Rob Herring)
- Add ACS and pciehp quirks for HXT SD4800 (Shunyong Yang)
- Consolidate Rohm Vendor ID definitions (Andy Shevchenko)
- Use u32 (not __u32) for things not exposed to userspace (Logan
Gunthorpe)
- Fix locking semantics of bus and slot reset interfaces (Alex
Williamson)
- Update PCIEPORTBUS Kconfig help text (Hou Zhiqiang)
- Allow portdrv to claim subtractive decode Ports so PCIe services will
work for them (Honghui Zhang)
- Report PCIe links that become degraded at run-time (Alexandru
Gagniuc)
- Blacklist Gigabyte X299 Root Port power management to fix Thunderbolt
hotplug (Mika Westerberg)
- Revert runtime PM suspend/resume callbacks that broke PME on network
cable plug (Mika Westerberg)
- Disable Data Link State Changed interrupts to prevent wakeup
immediately after suspend (Mika Westerberg)
- Extend altera to support Stratix 10 (Ley Foon Tan)
- Allow building altera driver on ARM64 (Ley Foon Tan)
- Replace Douglas with Tom Joseph as Cadence PCI host/endpoint
maintainer (Lorenzo Pieralisi)
- Add DT support for R-Car RZ/G2E (R8A774C0) (Fabrizio Castro)
- Add dra72x/dra74x/dra76x SoC compatible strings (Kishon Vijay Abraham I)
- Enable x2 mode support for dra72x/dra74x/dra76x SoC (Kishon Vijay
Abraham I)
- Configure dra7xx PHY to PCIe mode (Kishon Vijay Abraham I)
- Simplify dwc (remove unnecessary header includes, name variables
consistently, reduce inverted logic, etc) (Gustavo Pimentel)
- Add i.MX8MQ support (Andrey Smirnov)
- Add message to help debug dwc MSI-X mask bit errors (Gustavo
Pimentel)
- Work around imx7d PCIe PLL erratum (Trent Piepho)
- Don't assert qcom reset GPIO during probe (Bjorn Andersson)
- Skip dwc MSI init if MSIs have been disabled (Lucas Stach)
- Use memcpy_fromio()/memcpy_toio() instead of plain memcpy() in PCI
endpoint framework (Wen Yang)
- Add interface to discover supported endpoint features to replace a
bitfield that wasn't flexible enough (Kishon Vijay Abraham I)
- Implement the new supported-feature interface for designware-plat,
dra7xx, rockchip, cadence (Kishon Vijay Abraham I)
- Fix issues with 64-bit BAR in endpoints (Kishon Vijay Abraham I)
- Add layerscape endpoint mode support (Xiaowei Bao)
- Remove duplicate struct hv_vp_set in favor of struct hv_vpset (Maya
Nakamura)
- Rework hv_irq_unmask() to use cpumask_to_vpset() instead of
open-coded reimplementation (Maya Nakamura)
- Align Hyper-V struct retarget_msi_interrupt arguments (Maya Nakamura)
- Fix mediatek MMIO size computation to enable full size of available
MMIO space (Honghui Zhang)
- Fix mediatek DMA window size computation to allow endpoint DMA access
to full DRAM address range (Honghui Zhang)
- Fix mvebu prefetchable BAR regression caused by common bridge
emulation that assumed all bridges had prefetchable windows (Thomas
Petazzoni)
- Make advk_pci_bridge_emul_ops static (Wei Yongjun)
- Configure MPS settings for VMD root ports (Jon Derrick)
* tag 'pci-v5.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (92 commits)
PCI: Update PCIEPORTBUS Kconfig help text
PCI: Fix "try" semantics of bus and slot reset
PCI/LINK: Report degraded links via link bandwidth notification
dt-bindings: PCI: altera: Add altr,pcie-root-port-2.0
PCI: altera: Enable driver on ARM64
PCI: altera: Add Stratix 10 PCIe support
PCI/PME: Fix possible use-after-free on remove
PCI: aardvark: Make symbol 'advk_pci_bridge_emul_ops' static
PCI: dwc: skip MSI init if MSIs have been explicitly disabled
PCI: hv: Refactor hv_irq_unmask() to use cpumask_to_vpset()
PCI: hv: Replace hv_vp_set with hv_vpset
PCI: hv: Add __aligned(8) to struct retarget_msi_interrupt
PCI: mediatek: Enlarge PCIe2AHB window size to support 4GB DRAM
PCI: mediatek: Fix memory mapped IO range size computation
PCI: dwc: Remove superfluous shifting in definitions
PCI: dwc: Make use of GENMASK/FIELD_PREP
PCI: dwc: Make use of BIT() in constant definitions
PCI: dwc: Share code for dw_pcie_rd/wr_other_conf()
PCI: dwc: Make use of IS_ALIGNED()
PCI: imx6: Add code to request/control "pcie_aux" clock for i.MX8MQ
...
Here is the big USB/PHY driver pull request for 5.1-rc1.
The usual set of gadget driver updates, phy driver updates (you will
have a merge issue with Kconfig and Makefile), xhci updates, and typec
additions. Also included in here are a lot of small cleanups and fixes
and driver updates where needed.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXH+hsw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynfNwCgqKKg+MxJ9pFjrwfWYOrbk+BBe2UAn2Elp4ia
8FTdneQfN2J8Hhc6KGXE
=Kx9I
-----END PGP SIGNATURE-----
Merge tag 'usb-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big USB/PHY driver pull request for 5.1-rc1.
The usual set of gadget driver updates, phy driver updates, xhci
updates, and typec additions. Also included in here are a lot of small
cleanups and fixes and driver updates where needed.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (167 commits)
wusb: Remove unnecessary static function ckhdid_printf
usb: core: make default autosuspend delay configurable
usb: core: Fix typo in description of "authorized_default"
usb: chipidea: Refactor USB PHY selection and keep a single PHY
usb: chipidea: Grab the (legacy) USB PHY by phandle first
usb: chipidea: imx: set power polarity
dt-bindings: usb: ci-hdrc-usb2: add property power-active-high
usb: chipidea: imx: remove unused header files
usb: chipidea: tegra: Fix missed ci_hdrc_remove_device()
usb: core: add option of only authorizing internal devices
usb: typec: tps6598x: handle block writes separately with plain-I2C adapters
usb: xhci: Fix for Enabling USB ROLE SWITCH QUIRK on INTEL_SUNRISEPOINT_LP_XHCI
usb: xhci: fix build warning - missing prototype
usb: xhci: dbc: Fixing typo error.
usb: xhci: remove unused member 'parent' in xhci_regset struct
xhci: tegra: Prevent error pointer dereference
USB: serial: option: add Telit ME910 ECM composition
usb: core: Replace hardcoded check with inline function from usb.h
usb: core: skip interfaces disabled in devicetree
usb: typec: mux: remove redundant check on variable match
...
The APM X-Gene platform is now maintained by folks from Ampere
computing that took over the product line a while ago, this gets
reflected in the MAINTAINERS file.
Cleanups continue on the older mach-davinci and mach-pxa platform,
to get them to be more like the modern ones. For pxa, we
now remove the Raumfeld platform code as it now works with
device tree based booting.
i.MX adds a couple new features for the i.MX7ULP SoC
Mediatek gains support for a new SoC: MT7629 is a new wireless
router platform, following MT7623.
Aside from those, there are the usual minor cleanups and bugfixes
across several platforms.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=vxwd
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Arnd Bergmann:
"The APM X-Gene platform is now maintained by folks from Ampere
computing that took over the product line a while ago, this gets
reflected in the MAINTAINERS file.
Cleanups continue on the older mach-davinci and mach-pxa platform, to
get them to be more like the modern ones. For pxa, we now remove the
Raumfeld platform code as it now works with device tree based booting.
i.MX adds a couple new features for the i.MX7ULP SoC
Mediatek gains support for a new SoC: MT7629 is a new wireless router
platform, following MT7623.
Aside from those, there are the usual minor cleanups and bugfixes
across several platforms"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (49 commits)
MAINTAINERS: Update Ampere email address
usb: ohci-da8xx: remove unused callbacks from platform data
ARM: davinci: da830-evm: remove legacy usb helpers
ARM: davinci: omapl138-hawk: remove legacy usb helpers
usb: ohci-da8xx: add vbus and overcurrent gpios
ARM: davinci: da830-evm: use gpio lookup entries for usb gpios
ARM: davinci: omapl138-hawk: use gpio lookup entries for usb gpios
usb: ohci-da8xx: add a helper pointer to &pdev->dev
usb: ohci-da8xx: add a new line after local variables
arm64: meson: enable g12a clock controller
MAINTAINERS: Add entry for uDPU board
ARM: davinci: da850-evm: use GPIO hogs instead of the legacy API
arm: mediatek: add MT7629 smp bring up code
Revert "ARM: mediatek: add MT7623a smp bringup code"
dt-bindings: soc: fix typo of MT8173 power dt-bindings
ARM: meson: remove COMMON_CLK_AMLOGIC selection
arm64: meson: remove COMMON_CLK_AMLOGIC selection
ARM: lpc32xx: remove platform data of ARM PL111 LCD controller
ARM: lpc32xx: remove platform data of ARM PL180 SD/MMC controller
ARM: lpc32xx: Use kmemdup to replace duplicating its implementation
...
This static inline is unnecessary and can be removed
by using the vsprintf %ph extension.
This reduces overall object size by more than 2K.
Reported-by: Louis Taylor <louis@kragniz.eu>
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Louis Taylor <louis@kragniz.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the default autosuspend delay configurable at build time.
This is useful for systems that require a non-standard value as
it avoids relying on the command line being properly set.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor the code in charge of looking up the USB PHY when no platdata
is provided. Attempt to get a generic USB PHY first, then look for a
legacy USB PHY through device-tree and finally get any registered PHY
with the correct type.
This way, only a single USB PHY is obtained and the flow is easier to
understand and follow.
All error pointers (except for EPROBE_DEFER) are considered as PHY
not found.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the chipidea driver bindings, the USB PHY is specified via
the "phys" phandle node. However, this only takes effect for USB PHYs
that use the common PHY framework. For legacy USB PHYs, a simple lookup
based on the USB PHY type is done instead.
This does not play out well when more than one USB PHY is registered,
since the first registered PHY matching the type will always be
returned regardless of what the driver was bound to.
Fix this by looking up the PHY based on the "phys" phandle node.
Although generic PHYs are rather matched by their "phys-name" and not
the "phys" phandle directly, there is no helper for similar lookup on
legacy PHYs and it's probably not worth the effort to add it.
When no legacy USB PHY is found by phandle, fallback to grabbing any
registered USB2 PHY. This ensures backward compatibility if some users
were actually relying on this mechanism.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support to set the power line polarity for i.MX SoCs.
To let the USB controller control the power it may be necessary to
configure the polarity of the power line. So far the polarity was
configured by Bootloader or alternatively the power line was muxed
as gpio and driven by a regulator.
Also make use of of_property_read_bool.
Signed-off-by: Philipp Puschmann <philipp.puschmann@emlix.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Those 2 headers files are not required now.
Signed-off-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ChipIdea's platform device need to be unregistered on Tegra's driver
module removal.
Fixes: dfebb5f43a ("usb: chipidea: Add support for Tegra20/30/114/124")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hedberg says:
====================
Here's the main bluetooth-next pull request for the 5.1 kernel.
- Fixes & improvements to mediatek, hci_qca, btrtl, and btmrvl HCI drivers
- Fixes to parsing invalid L2CAP config option sizes
- Locking fix to bt_accept_enqueue()
- Add support for new Marvel sd8977 chipset
- Various other smaller fixes & cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
On Chrome OS we want to use USBguard to potentially limit access to USB
devices based on policy. We however to do not want to wait for userspace to
come up before initializing fixed USB devices to not regress our boot
times.
This patch adds option to instruct the kernel to only authorize devices
connected to the internal ports. Previously we could either authorize
all or none (or, by default, we'd only authorize wired devices).
The behavior is controlled via usbcore.authorized_default command line
option.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are a couple of new device ids for 5.1-rc1.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHQEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXG7PogAKCRALxc3C7H1l
CLtbAP9N7qnHiOflSg8sK3E4hBI5ZaVKQuJwObEOMJY+s6jeYwD1E3sbyWKGHu+2
R8Px/FbKC3JWMUIhO7bVlyvsQDcQAA==
=hG64
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.1-rc1-2' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial fixes for 5.1-rc1
Here are a couple of new device ids for 5.1-rc1.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-5.1-rc1-2' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: ftdi_sio: add ID for Hjelmslund Electronics USB485
USB: serial: cp210x: add ID for Ingenico 3070
Here are the USB-serial updates for 5.1-rc1, including:
- support for the last three GPIOs on cp2102n devices
- gpio support for cp2104
- support for using cp210x gpios with autosuspend
- proper error handling for unsupported cp2105 line speeds
Included is also a new modem device id.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXG7M3AAKCRALxc3C7H1l
CBUpAQD/N1G1G38alGS0zwn/u9krsVyLm5Y1gK8MWXvpkcGBXwEAoSYrMjoRAAdR
Ks4rQdSyYonbE3zENXp5d3beCRM4pQY=
=GQ5N
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.1-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 5.1-rc1
Here are the USB-serial updates for 5.1-rc1, including:
- support for the last three GPIOs on cp2102n devices
- gpio support for cp2104
- support for using cp210x gpios with autosuspend
- proper error handling for unsupported cp2105 line speeds
Included is also a new modem device id.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-5.1-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Telit ME910 ECM composition
USB: serial: cp210x: fix GPIO in autosuspend
USB: serial: cp210x: add minimum baud rate for CP2105 SCI
USB: serial: cp210x: add GPIO support for CP2104
USB: serial: cp210x: support all gpios on CP2102N QFN28 package
Commit 1a2f474d32 handles block _reads_ separately with plain-I2C
adapters, but the problem described with regmap-i2c not handling
SMBus block transfers (i.e. read and writes) correctly also exists
with writes.
As workaround, this patch adds a block write function the same way
1a2f474d32 adds a block read function.
Fixes: 1a2f474d32 ("usb: typec: tps6598x: handle block reads separately with plain-I2C adapters")
Fixes: 0a4c005bd1 ("usb: typec: driver for TI TPS6598x USB Power Delivery controllers")
Signed-off-by: Nikolaus Voss <nikolaus.voss@loewensteinmedical.de>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fix enables USB role feature on intel commercial nuc
platform which is based on Kabylake chipset.
Signed-off-by: Balaji Manoharan <m.balaji@intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix build warning when building drivers/usb/host/xhci-mem.o with W=1 due
to missing prototype for xhci_free_virt_devices_depth_first.
This function is only used in xhci-mem.c so just make it static.
Signed-off-by: Jean-Philippe Menil <jpmenil@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The member @parent of xhci_regset struct is not used in fact,
so remove it
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During initialization, the host and super-speed power domains will
contain an ERR_PTR() encoded error code rather than being NULL. To
avoid a crash, use a !IS_ERR_OR_NULL() condition during cleanup.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Fixes: 6494a9ad86 ("usb: xhci: tegra: Add genpd support")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All users of dma_declare_coherent want their allocations to be
exclusive, so default to exclusive allocations.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If an interface has an associated devicetree node with status disabled,
do not register the device. This is useful for boards with a built-in
multifunction USB device where some functions are broken or otherwise
undesired.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All the code paths that lead to the return statement are where
match is always true, hence the check to see if it is true is
redundant and can be removed.
Detected by CoverityScan, CID#14769672 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current GPIO code in cp210x fails to take USB autosuspend into account,
making it practically impossible to use GPIOs with autosuspend enabled
without user configuration. Fix this like for ftdi_sio in a previous patch.
Tested on a CP2102N.
Signed-off-by: Karoly Pados <pados@pados.hu>
Fixes: cf5276ce78 ("USB: serial: cp210x: Adding GPIO support for CP2105")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
In case the "linux,extcon-name" property is defined but device itself
is not ready, defer the probe.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'rv' is the correct return value, pass it upstream instead of 0
Fixes: 17d80d562f ("USB: autosuspend for cdc-wdm")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/usb/host/oxu210hp-hcd.c: In function 'scan_periodic':
drivers/usb/host/oxu210hp-hcd.c:2256:13: warning:
variable 'uframes' set but not used [-Wunused-but-set-variable]
drivers/usb/host/oxu210hp-hcd.c: In function 'oxu_urb_enqueue':
drivers/usb/host/oxu210hp-hcd.c:2835:6: warning:
variable 'transfer_buffer_length' set but not used [-Wunused-but-set-variable]
They are never used since introduction.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a spelling mistake in a dev_err message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.
So, change the following form:
sizeof(*packet_desc) + (sizeof(packet_desc->PacketLength[0]) * seg->isoc_frame_count)
to :
struct_size(packet_status, PacketStatus, seg->isoc_frame_count);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
Notice that, in this case, variable len is not necessary, hence
it is removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
Notice that, in this case, variable size is not necessary, hence
it is removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The return from the call to fwnode_property_read_u16_array is int,
it can be a negative error code however this is being assigned to
an size_t variable 'nval', hence the check is always false.
Fix this by making 'nval' an int.
Detected by Coccinelle ("Unsigned expression compared with
zero: nval < 0")
Fixes: 96a6d031ca ("usb: typec: mux: Find the muxes by also matching against the device node")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DaVinci SoC updates for v5.1 (part 2)
This pull request contains changes needed to help get rid of
hard-coded GPIO base value passed from DaVinci platform data.
The OHCI related changes also help by moving over-current support
from board-files to OHCI driver making future DT-coversion easy.
The OHCI parts are acked by its maintainer.
* tag 'davinci-for-v5.1/soc-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
usb: ohci-da8xx: remove unused callbacks from platform data
ARM: davinci: da830-evm: remove legacy usb helpers
ARM: davinci: omapl138-hawk: remove legacy usb helpers
usb: ohci-da8xx: add vbus and overcurrent gpios
ARM: davinci: da830-evm: use gpio lookup entries for usb gpios
ARM: davinci: omapl138-hawk: use gpio lookup entries for usb gpios
usb: ohci-da8xx: add a helper pointer to &pdev->dev
usb: ohci-da8xx: add a new line after local variables
ARM: davinci: da850-evm: use GPIO hogs instead of the legacy API
ARM: davinci: mityomapl138: use device properties for at24 eeprom
ARM: davinci: mityomapl138: use nvmem notifiers
ARM: davinci: remove dead code related to MAC address reading
ARM: davinci: sffsdr: use device properties for at24 eeprom
ARM: davinci: sffsdr: fix the at24 eeprom device name
ARM: davinci: dm646x-evm: use device properties for at24 eeprom
ARM: davinci: dm644x-evm: use device properties for at24 eeprom
ARM: davinci: da830-evm: use device properties for at24 eeprom
ARM: davinci: dm365-evm: use device properties for at24 eeprom
ARM: davinci: mityomapl138: don't read the MAC address from machine code
ARM: davinci: da850-evm: remove dead MTD code
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This adds the USB ID of the Hjelmslund Electronics USB485 Iso stick.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Dwc3 now works on TI's AM6xx platforms. Also on dwc3 we have a few
changes which improve request cancellation and some improvements to
how we print to the trace buffer.
Renesas_usb3 got support for r8a774c0 device.
Dwc2 got scatter-gather support.
Apart from these, the usual set of minor fixes and all sorts of small
details.
-----BEGIN PGP SIGNATURE-----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=4fTL
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: changes for v5.1 merge window
Dwc3 now works on TI's AM6xx platforms. Also on dwc3 we have a few
changes which improve request cancellation and some improvements to
how we print to the trace buffer.
Renesas_usb3 got support for r8a774c0 device.
Dwc2 got scatter-gather support.
Apart from these, the usual set of minor fixes and all sorts of small
details.
* tag 'usb-for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (40 commits)
usb: phy: twl6030-usb: fix possible use-after-free on remove
usb: misc: usbtest: add super-speed isoc support
usb: dwc3: Reset num_trbs after skipping
usb: dwc3: gadget: don't enable interrupt when disabling endpoint
fotg210-udc: pass struct device to DMA API functions
fotg210-udc: remove a bogus dma_sync_single_for_device call
usb: gadget: Change Andrzej Pietrasiewicz's e-mail address
usb: f_fs: Avoid crash due to out-of-scope stack ptr access
usb: dwc3: haps: Workaround matching VID PID
usb: gadget: f_fs: preserve wMaxPacketSize across usb_ep_autoconfig() call
usb: gadget: move non-super speed code out of usb_ep_autoconfig_ss()
usb: gadget: function: sync f_uac1 ac header baInterfaceNr
usb: dwc2: gadget: Add scatter-gather mode
usb: gadget: fix various indentation issues
usb: dwc2: Fix EP TxFIFO number setting
udc: net2280: Fix net2280_disable
USB: gadget: Improve kerneldoc for usb_ep_dequeue()
usb: dwc3: debug: purge usage of strcat
usb: dwc3: trace: pass trace buffer size to decoding functions
usb: dwc3: gadget: remove DWC3_EP_END_TRANSFER_PENDING
...
When the connections are defined in firmware, struct
device_connection will have the fwnode member pointing to
the device node (struct fwnode_handle) of the requested
device, and the endpoint will not be used at all in that
case.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the connections are defined in firmware, struct
device_connection will have the fwnode member pointing to
the device node (struct fwnode_handle) of the requested
device, and the endpoint will not be used at all in that
case.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the connections are defined in firmware, struct
device_connection will have the fwnode member pointing to
the device node (struct fwnode_handle) of the requested
device, and the endpoint will not be used at all in that
case.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Tested-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since with accessory modes there is no need for additional
identification when requesting a handle to the mux, we can
replace the second parameter that is passed to the
typec_mux_get() function with a pointer to alternate mode
description structure, and simply passing NULL with
accessory modes.
This change means the naming of the mux device connections
can be updated. Alternate and Accessory Modes will both be
handled with muxes named "mode-switch", and the orientation
switches will be named "orientation-switch".
Future identification of the alternate modes will be later
done using device property "svid" of the mux.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To prevent loading of the driver when the PD controller is
still in some operational mode that the driver does not
support, checking the mode in driver probe callback
function.
TI PD controllers may be in undefined mode of operation
for example when the application code (firmware) is
completely missing.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tcpm_update_source_capabilities() and tcpm_update_sink_capabilities()
are not used anywhere, and I don't recall why I introduced those functions
in the first place. Effectively that means that we don't know if they even
work, or ever did. Lets remove them.
Reported-by: Kyle Tso <kyletso@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Kyle Tso <kyletso@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/usb/musb/musb_host.c: In function ‘musb_advance_schedule’:
drivers/usb/musb/musb_host.c:374:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (qh->mux == 1) {
^
drivers/usb/musb/musb_host.c:383:3: note: here
case USB_ENDPOINT_XFER_ISOC:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In remove(), use cancel_delayed_work_sync() to cancel the
delayed work. Otherwise there's a chance that this work
will continue to run until after the device has been removed.
This issue was detected with the help of Coccinelle.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Bin Liu <b-liu@ti.com>
Fixes: b6a619a883 ("usb: phy: Check initial state for twl6030")
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The calculation of packet number within microframe is different between
high-speed and super-speed endpoint, we add support for super-speed
in this patch.
Cc: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Currently req->num_trbs is not reset after the TRBs are skipped and
processed from the cancelled list. The gadget driver may reuse the
request with an invalid req->num_trbs, and DWC3 will incorrectly skip
trbs. To fix this, simply reset req->num_trbs to 0 after skipping
through all of them.
Fixes: c3acd59014 ("usb: dwc3: gadget: use num_trbs when skipping TRBs on ->dequeue()")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since we're disabling the endpoint anyway, we don't worry about
getting endpoint command completion interrupt.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch does not change any functionality.
Cc: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A statement is indented too deeply, fix this by removing a tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two users upstream which register external callbacks for
switching the port power on/off and overcurrent protection. Both
users only use two GPIOs for that. Instead of having that functionality
in the board files, move the logic into the OHCI driver - including
the interrupt handler for overcurrent detection.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add a helper pointer to &pdev->dev. This improves readability by
removing all the &pdev->dev dereferencing.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add a new line after local variables. This improves the coding style.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The Kconfig entry previously depended on USB_OTG_BLACKLIST_HUB
unconditionally, which is an option that is only available when
CONFIG_USB is enabled. However, the USB IP in the JZ4740 SoC does not
support host mode, only gadget mode, so it makes sense to allow it to
build when CONFIG_USB is not set.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Depending on MACH_JZ4740 prevent us from creating a generic kernel that
works on more than one MIPS board. Instead, we just depend on MIPS being
set.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for probing the driver from devicetree.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A return statement is indented one level too far, fix this by removing
a tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DMA API generally relies on a struct device to work properly, and
only barely works without one for legacy reasons. Pass the easily
available struct device from the platform_device to remedy this.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dma_map_single already transfers ownership to the device.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
My @samusung.com address is going to cease existing soon, so change it to
an address which can actually be used to contact me.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since the 5.0 merge window opened, I've been seeing frequent
crashes on suspend and reboot with the trace:
[ 36.911170] Unable to handle kernel paging request at virtual address ffffff801153d660
[ 36.912769] Unable to handle kernel paging request at virtual address ffffff800004b564
...
[ 36.950666] Call trace:
[ 36.950670] queued_spin_lock_slowpath+0x1cc/0x2c8
[ 36.950681] _raw_spin_lock_irqsave+0x64/0x78
[ 36.950692] complete+0x28/0x70
[ 36.950703] ffs_epfile_io_complete+0x3c/0x50
[ 36.950713] usb_gadget_giveback_request+0x34/0x108
[ 36.950721] dwc3_gadget_giveback+0x50/0x68
[ 36.950723] dwc3_thread_interrupt+0x358/0x1488
[ 36.950731] irq_thread_fn+0x30/0x88
[ 36.950734] irq_thread+0x114/0x1b0
[ 36.950739] kthread+0x104/0x130
[ 36.950747] ret_from_fork+0x10/0x1c
I isolated this down to in ffs_epfile_io():
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/usb/gadget/function/f_fs.c#n1065
Where the completion done is setup on the stack:
DECLARE_COMPLETION_ONSTACK(done);
Then later we setup a request and queue it, and wait for it:
if (unlikely(wait_for_completion_interruptible(&done))) {
/*
* To avoid race condition with ffs_epfile_io_complete,
* dequeue the request first then check
* status. usb_ep_dequeue API should guarantee no race
* condition with req->complete callback.
*/
usb_ep_dequeue(ep->ep, req);
interrupted = ep->status < 0;
}
The problem is, that we end up being interrupted, dequeue the
request, and exit.
But then the irq triggers and we try calling complete() on the
context pointer which points to now random stack space, which
results in the panic.
Alan Stern pointed out there is a bug here, in that the snippet
above "assumes that usb_ep_dequeue() waits until the request has
been completed." And that:
wait_for_completion(&done);
Is needed right after the usb_ep_dequeue().
Thus this patch implements that change. With it I no longer see
the crashes on suspend or reboot.
This issue seems to have been uncovered by behavioral changes in
the dwc3 driver in commit fec9095bde ("usb: dwc3: gadget:
remove wait_end_transfer").
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Zeng Tao <prime.zeng@hisilicon.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: Thinh Nguyen <thinh.nguyen@synopsys.com>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Jerry Zhang <zhangjerry@google.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Vincent Pelletier <plr.vincent@gmail.com>
Cc: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linux USB List <linux-usb@vger.kernel.org>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It's not needed. Moving everything from it to trace.c.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because of UCSI, we have to support alt mode enter/exit
reporting even when there is no alt mode driver bind to the
alt mode device. With UCSI a firmware handles the alternate
modes, and the modes are entered automatically from OS PoW.
Changing typec_altmode_update_active() so that the driver
module ref count is incremented/decremented only if there
really is a driver for the alt mode. That avoids a NULL
pointer dereference from happening when the driver is
missing.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The helpers used for reading and writing the pin assignment
from and to the Configuration VDO will be useful in GPU
drivers, and also UCSI driver after DisplayPort alt mode
support is added to it.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f13912d3f0 introduced changes to the usb_choose_configuration function
to better support USB Audio UAC3-compatible devices. However, there are a few
problems with this patch. First of all, it adds new "if" clauses in the middle
of an existing "if"/"else if" tree, which obviously breaks pre-existing logic.
Secondly, since it continues iterating over configurations in one of the branches,
other code in the loop can choose an unintended configuration. Finally,
if an audio device's first configuration is UAC3-compatible, and there
are multiple UAC3 configurations, the second one would be chosen, due to
the first configuration never being checked for UAC3-compatibility.
Commit ff2a8c532c tries to fix the second issue, but it goes about it in a
somewhat unnecessarily convoluted way, in my opinion, and does nothing
to fix the first or the last one.
This patch tries to rectify problems described by essentially rewriting
code introduced in f13912d3f0. Notice the code was moved to *before*
the "if"/"else if" tree.
Signed-off-by: Nikolay Yakimov <root@livid.pp.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On plug-in of my USB-C device, its USB_SS_PORT_LS_SS_INACTIVE
link state bit is set. Greping all the kernel for this bit shows
that the port status requests a warm-reset this way.
This just happens, if its the only device on the root hub, the hub
therefore resumes and the HCDs status_urb isn't yet available.
If a warm-reset request is detected, this sets the hubs event_bits,
which will prevent any auto-suspend and allows the hubs workqueue
to warm-reset the port later in port_event.
Signed-off-by: Jan-Marek Glogowski <glogow@fbihome.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is how this device appears in kernel log:
usb 3-1: new full-speed USB device number 18 using xhci_hcd
usb 3-1: New USB device found, idVendor=0b00, idProduct=3070
usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 3-1: Product: Ingenico 3070
usb 3-1: Manufacturer: Silicon Labs
usb 3-1: SerialNumber: 0001
Apparently this is a POS terminal with embedded USB-to-Serial converter.
Cc: stable@vger.kernel.org
Signed-off-by: Ivan Mironov <mironov.ivan@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add minimum baud rate to the cp210x driver.
According to the datasheet for CP2105, the SCI supports 2400 as the
lowest baud rate. As this is not heeded in the current code, an error
message 'failed set req 0x1e size 4 status: -32' when trying to set a
lower baud rate such as 300.
The other cp210x models to date supports a minimum baud rate of 300.
Signed-off-by: Johanna Abrahamsson <johanna.abrahamsson@afconsult.com>
[ johan: simplify min_speed init, move clamp after comment, and drop
unused serial-data pointer from cp210x_get_actual_rate() ]
Signed-off-by: Johan Hovold <johan@kernel.org>
i.MX6QP and i.MX7D platform use a PCIe controller with the same VID and
PID as this USB controller. The system may incorrectly match this driver
to that PCIe controller. To workaround this, specifically use class type
USB with PCI device ID to prevent incorrect driver matching.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
usb_ep_autoconfig() treats the passed descriptor as if it were an fs
descriptor. In particular, for bulk endpoints, it clips wMaxPacketSize
to 64. This patch preserves the original value.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The moved code refers to non-super speed endpoints only. This patch also
makes the comment stress the fact, that autoconfigured descriptor might
need some adjustments.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
f_uac1 audio control header descriptor default set
baInterfaceNr[]={1,2}, but usb gadget make a configuration descriptor
with more interfaces combination, it can not confirm f_uac1 function
linked first. So always keep baInterfaceNr[]={1,2} is correct, and it
is necessary to sync baInterfaceNr[] with usb_interface_id() value.
Signed-off-by: Liang Shengjun <liangshengjun@hisilicon.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds support for transferring requests, which are
non-contiguous in physical memory, i.e. the data buffer is described by
a scatter-list. This allows transferring large requests without relying
on error-prone contiguous buffer allocations. This way of allocating
requests is already implemented in functionfs and TCM USB functions and
automatically used if UDC driver advertises scatter-gather suppport.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
[mszyprow: fixed null pointer issue, rewrote commit message]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There are a bunch of various indentation issues, clean these up.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case when some EP IN is frequently reused, i.e. enabled/disabled by
function driver. It is required to clear TxFIFO number field in DIEPCTL
register before setting new number. Otherwise there is probability to
have same TxFIFO number for different EP's because of OR operator.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
A reset e.g. calling ep_reset_338x() can happen while endpoints
are enabled. The ep_reset_338x() sets ep->desc = NULL to mark
endpoint being invalid. A subsequent call of net2280_disable will
fail and return -EINVAL to parent function usb_ep_disable(),
which will fail, too, and do not set the member ep->enabled = false.
See:
https://elixir.bootlin.com/linux/v5.0-rc5/source/drivers/usb/gadget/udc/core.c#L139
This fix ignores dp->desc and allows net2280_disable() to succeed.
Subsequent calls to usb_ep_enable()/usb_ep_disable() succeeds.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Commit bf594c1070 ("USB: gadget: Document that certain ep operations
can be called in interrupt context") documented that usb_ep_dequeue()
may be called in a non-process context. It follows that the routine
must not sleep or wait for events.
However, the routine's existing kerneldoc seems to imply that it will
wait until the request being cancelled has fully completed. This is
not so, and thus the comment needs to be improved. Misunderstanding
this point may very well have been responsible for a bug recently
uncovered in the f_fs function.
The updated comment explicitly says that the routine may return before
the request's completion handler is called.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
No real need for bidi support once the OSD code is gone.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Due to the patch that makes TMF handling synchronous the
write_pending_status() callback function is no longer called. Hence remove
it.
Acked-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Andy Grover <agrover@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The CP2104 chips feature 4 controllable GPIO pins, which are similar to
the ones on CP2102N chip (output-only when push-pull, output or
simulated input mode when open-drain).
Add support for the GPIO pins for cp210x driver. The pin get/set routine
is shared with CP2102N, but the pinconf initialization code is not
shared because the acquisition of GPIO configuration in OTP ROM is
similar to CP2105, not CP2102N.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Johan Hovold <johan@kernel.org>
Instead of assuming that our buffer is big enough, let's pass the
buffer size around so printing functions can make sure they won't
overflow the buffer.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It is better to initialize the variable 'cfgno' in the for loop than
at the current place.
Signed-off-by: Suwan Kim <suwan.kim027@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we modified the code to fix a race condition, it's clear that
DWC3_EP_END_TRANSFER_PENDING is unnecessary, considering that
DWC3_EP_TRANSFER_STARTED will remain set until End Transfer completes.
Tested-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There is a rare race condition that may happen during a Disconnect
Interrupt if we have a started request that happens to be
dequeued *after* completion of End Transfer command. If that happens,
that request will be left waiting for completion of an End Transfer
command that will never happen.
If End Transfer command has already completed before, we are safe to
giveback the request straight away.
Tested-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We have a proper flag for testing that we have a valid transfer in
flight, let's use that instead.
This patch is in preparation to fix a rare race condition that happens
upon Disconnect Interrupt.
Tested-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Move the Rohm Vendor ID to pci_ids.h instead of defining it in several
drivers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
We must wait until End Transfer completes in order to clear
DWC3_EP_TRANSFER_STARTED, otherwise we may confuse the driver.
This patch is in preparation to fix a rare race condition that happens
upon Disconnect Interrupt.
Tested-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When Sink negotiates PPS, the voltage range of selected PPS APDO might
not cover the previous voltage (out_volt). If the previous out_volt is
lower than the new min_volt, the output voltage in RDO might be set to
an invalid value. For instance, supposed that the previous voltage is
5V, and the new voltage range in the APDO is 7V-12V. Then the output
voltage in the RDO should not be set to 5V which is lower than the
possible min_volt 7V.
Fix this by choosing the maximal value between the previous voltage and
the new min_volt first. And ensure that this value will not exceed the
new max_volt. The new out_volt will fall within the new voltage range
while being the closest value compared to the previous out_volt.
Signed-off-by: Kyle Tso <kyletso@google.com>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Fixes: c710d0bb76 ("usb: typec: tcpm: Extend the matching rules on PPS APDO selection")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dwc3 got a fix for cases when gadget driver queue an OUT request of
length 0; this is a case that has been overlooked for quite some time
now.
Exynos' dwc3 glue layer got a fix on the error path for those cases
where clk_prepare_enable() fails.
TI's AM335x PHY driver got a fix for a race condition during
probe. This race happened because driver was powering off the PHY only
after adding the PHY handle to the framework. The result is that we
could fall into a situation where user of the PHY (MUSB) could call
phy_init() before phy driver's probe() called phy_poweroff() which
would result in a powered off PHY after phy_init() was called.
The old net2272 driver got a fix for an erroneous use of bitwise
negation.
-----BEGIN PGP SIGNATURE-----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=xcVV
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v5.0-rc4
Dwc3 got a fix for cases when gadget driver queue an OUT request of
length 0; this is a case that has been overlooked for quite some time
now.
Exynos' dwc3 glue layer got a fix on the error path for those cases
where clk_prepare_enable() fails.
TI's AM335x PHY driver got a fix for a race condition during
probe. This race happened because driver was powering off the PHY only
after adding the PHY handle to the framework. The result is that we
could fall into a situation where user of the PHY (MUSB) could call
phy_init() before phy driver's probe() called phy_poweroff() which
would result in a powered off PHY after phy_init() was called.
The old net2272 driver got a fix for an erroneous use of bitwise
negation.
* tag 'fixes-for-v5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
usb: phy: am335x: fix race condition in _probe
usb: dwc3: exynos: Fix error handling of clk_prepare_enable
usb: phy: fix link errors
usb: gadget: udc: net2272: Fix bitwise and boolean operations
usb: dwc3: gadget: Handle 0 xfer length for OUT EP
Handling short packets (length < max packet size) in the Inventra DMA
engine in the MUSB driver causes the MUSB DMA controller to hang. An
example of a problem that is caused by this problem is when streaming
video out of a UVC gadget, only the first video frame is transferred.
For short packets (mode-0 or mode-1 DMA), MUSB_TXCSR_TXPKTRDY must be
set manually by the driver. This was previously done in musb_g_tx
(musb_gadget.c), but incorrectly (all csr flags were cleared, and only
MUSB_TXCSR_MODE and MUSB_TXCSR_TXPKTRDY were set). Fixing that problem
allows some requests to be transferred correctly, but multiple requests
were often put together in one USB packet, and caused problems if the
packet size was not a multiple of 4. Instead, set MUSB_TXCSR_TXPKTRDY
in dma_controller_irq (musbhsdma.c), just like host mode transfers.
This topic was originally tackled by Nicolas Boichat [0] [1] and is
discussed further at [2] as part of his GSoC project [3].
[0] https://groups.google.com/forum/?hl=en#!topic/beagleboard-gsoc/k8Azwfp75CU
[1] b0be3b6cc1:beagleboard-usbsniffer-kernel.git;a=patch;h=b0be3b6cc195ba732189b04f1d43ec843c3e54c9
[2] http://beagleboard-usbsniffer.blogspot.com/2010/07/musb-isochronous-transfers-fixed.html
[3] http://elinux.org/BeagleBoard/GSoC/USBSniffer
Fixes: 550a7375fe ("USB: Add MUSB and TUSB support")
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix vep_free_request() to return when usb_ep and usb_request are null
instead of calling WARN_ON.
Signed-off-by: Shuah Khan <shuah@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need to initialize the PHY from the driver's probe. It is done by
the core automatically and doing it twice would increment the
phy->powercount counter to 2 instead of 1. During later suspend
operation, the counter will be decremented to one, no phy->power_off()
will occur and worse than that, the following phy->power_on() at
resume time will also be skipped, failing the whole S2RAM operation.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mvebu xHCI host driver does not have suspend/resume support. Use of
the XHCI_RESET_ON_RESUME quirk is mandatory in order to avoid failures
after resume. This will work only if no USB device is plugged-in.
While at it, mention in the Kconfig file that this IP is also present
on the A3700 SoC.
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
[miquel.raynal@bootlin.com: Reword the commit message]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current implementation of the USB core does not take into account the
new PHY framework. Correct the situation by adding a call to
phy_set_mode() before phy_power_on().
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
power off the phy should be done before populate the phy. Otherwise,
am335x_init() could be called by the phy owner to power on the phy first,
then am335x_phy_probe() turns off the phy again without the caller knowing
it.
Fixes: 2fc711d763 ("usb: phy: am335x: Enable USB remote wakeup using PHY wakeup")
Cc: stable@vger.kernel.org # v3.18+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If clk_prepare_enable() fails in dwc3_exynos_probe() or in
dwc3_exynos_resume(), exynos->clks[0] is left undisabled
because of usage preincrement in while condition.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 9f2168367a ("usb: dwc3: exynos: Rework clock handling and prepare for new variants")
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix link errors when CONFIG_FSL_USB2_OTG is enabled and USB_OTG_FSM is
set to module then the following link error occurs.
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.o: in function `fsl_otg_ioctl':
drivers/usb/phy/phy-fsl-usb.c:1083: undefined reference to `otg_statemachine'
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.c:1083:(.text+0x574): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `otg_statemachine'
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.o: in function `fsl_otg_start_srp':
drivers/usb/phy/phy-fsl-usb.c:674: undefined reference to `otg_statemachine'
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.c:674:(.text+0x61c): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `otg_statemachine'
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.o: in function `fsl_otg_set_host':
drivers/usb/phy/phy-fsl-usb.c:593: undefined reference to `otg_statemachine'
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.c:593:(.text+0x7a4): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `otg_statemachine'
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.o: in function `fsl_otg_start_hnp':
drivers/usb/phy/phy-fsl-usb.c:695: undefined reference to `otg_statemachine'
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.c:695:(.text+0x858): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `otg_statemachine'
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.o: in function `a_wait_enum':
drivers/usb/phy/phy-fsl-usb.c:274: undefined reference to `otg_statemachine'
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.c:274:(.text+0x16f0): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `otg_statemachine'
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.o:drivers/usb/phy/phy-fsl-usb.c:619: more undefined references to `otg_statemachine' follow
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.o: in function `fsl_otg_set_peripheral':
drivers/usb/phy/phy-fsl-usb.c:619:(.text+0x1fa0): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `otg_statemachine'
make[1]: *** [Makefile:1020: vmlinux] Error 1
make[1]: Target 'Image' not remade because of errors.
make: *** [Makefile:152: sub-make] Error 2
make: Target 'Image' not remade because of errors.
Rework so that FSL_USB2_OTG depends on that the USB_OTG_FSM is builtin.
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
(!x & y) strikes again.
Fix bitwise and boolean operations by enclosing the expression:
intcsr & (1 << NET2272_PCI_IRQ)
in parentheses, before applying the boolean operator '!'.
Notice that this code has been there since 2011. So, it would
be helpful if someone can double-check this.
This issue was detected with the help of Coccinelle.
Fixes: ceb80363b2 ("USB: net2272: driver for PLX NET2272 USB device controller")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For OUT endpoints, zero-length transfers require MaxPacketSize buffer as
per the DWC_usb3 programming guide 3.30a section 4.2.3.3.
This patch fixes this by explicitly checking zero length
transfer to correctly pad up to MaxPacketSize.
Fixes: c6267a5163 ("usb: dwc3: gadget: align transfers to wMaxPacketSize")
Cc: stable@vger.kernel.org
Signed-off-by: Tejas Joglekar <joglekar@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that we have req->status, we don't need this extra flag
anymore. It's safe to remove it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Queueing the same request twice can introduce hard-to-debug
problems. At least one function driver - Android's f_mtp.c - is known
to cause this problem.
While that function is out-of-tree, this is a problem that's easy
enough to avoid.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch starts tracking dwc3_request status. A following patch will
build on top of this to prevent a request from being queued twice.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
RZ/G2E USB 3.0 implementation is like the one found on R-Car E3,
therefore add the same quirk.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We only have uvcg_dbg, uvcg_info, and uvcg_err, so add uvcg_warn macro
to print gadget device name and function name along with format.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Switch RX processing from tasklet to (delayed) work queue. This allows
receiver more room to process incoming data and prevents flood of
"ttyGS0: RX not scheduled?" messages on HS receive on slow CPU.
A side effect is 2.4MB/s zmodem transfer speed (up from 1.8MB/s)
on my test board.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Delete tab aligning a statement with the right hand side of a
preceding assignment rather than the left hand side.
Found with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The AM654 SoC contains a DWC3 controller with TI specific
wrapper. Add support for that.
Unlike the Keystone 2 case, for AM654 We don't need to
process any IRQs for basic USB operation.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
On v3.10a in dual-role mode, if port is in device mode
and gadget driver isn't loaded, the OTG event interrupts don't
come through.
It seems that if the core is configured to be OTG2.0 only,
then we can't leave the DCFG.DEVSPD at Super-speed (default)
if we expect OTG to work properly. It must be set to High-speed.
Fix this issue by configuring DCFG.DEVSPD to the supported
maximum speed at gadget init. Device tree still needs to provide
correct supported maximum speed for this to work.
This issue wasn't present on v2.40a but is seen on v3.10a.
It doesn't cause any side effects on v2.40a.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
According to Documentation/timers/timers-howto.txt, a driver should
use usleep_range() instead of udelay() on NON-ATOMIC CONTEXT if
"SLEEPING FOR ~USECS OR SMALL MSECS ( 10us - 20ms)".
Since the .hardware_init() and .power_ctrl() will run on NON-ATOMIC
CONTEXT, this patch replaces udelay() with usleep_range().
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a MSM8998 specific DT compatible so that we can properly bind to the
device and enable the USB controller.
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
'num' is a u8 variable, it never greater than 255,
So the if branch is dead code and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The QFN28 package version of the CP2102N has three additional gpio pins.
Add support for these.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fixes the following coccinelle warning:
./drivers/usb/misc/ftdi-elan.c:972:10-12: WARNING: possible condition with no effect (if == else)
./drivers/usb/misc/ftdi-elan.c:983:9-11: WARNING: possible condition with no effect (if == else)
./drivers/usb/misc/ftdi-elan.c:2052:11-13: WARNING: possible condition with no effect (if == else)
All these else/if branches just do the same thing actually as the last else branch,
So it can be merged into the last branch.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove debugfs if tcpm register port fails.
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB3503 chip can be used without any I2C connection, what is handled by
a simple platform device driver. Add support for resetting the chip (via
GPIO lines) during system suspend/resume cycle by adding calls to existing
suspend/resume functions used for E2C device.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove macros which are only wrappers around standard operations. When
we expand them into code, we see that sisusbcon_memsetw can simply use
memset16 and sisusbcon_putcs can just call memcpy. So make the code
compact.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the previous patch we see, that whole files are ifdeffed depending
on CONFIG options. So do not build the files at all if the CONFIG is not
enabled. (I.e. move the check from .c to Makefile.)
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two macros defined:
1) ifdef CONFIG_COMPAT => define SISUSB_NEW_CONFIG_COMPAT
2) ifdef CONFIG_USB_SISUSBVGA_CON => define INCL_SISUSB_CON
Remove the latter and make use only of the former. This removes one
layer of obfuscation.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert SISUSB_VADDR and SISUSB_HADDR to inline functions. Now, there
are no more hidden accesses to local variables (vc_data and
sisusb_usb_data).
sisusb_haddr returns unsigned long from now on, not u16 *, as ulong is
what every caller expects -- we can remove some casts.
Call sites were aligned to be readable too.
Use sisusb_haddr on 4 more places in sisusbcon_blank and
sisusbcon_scroll. It was open coded there with [x, y] being [0, 0].
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable 'empty_packets' does not used in any other places
except for self increment, so it can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB devices permanently connected to USB ports may be described in ACPI
tables and share ACPI devices with ports they are connected to. See [1]
for details.
This will allow us to describe sideband resources for devices, such as,
for example, hard reset line for BT USB controllers.
[1] https://docs.microsoft.com/en-us/windows-hardware/drivers/bringup/other-acpi-namespace-objects#acpi-namespace-hierarchy-and-adr-for-embedded-usb-devices
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Rajat Jain <rajatja@google.com> (changed how we get the usb_port)
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Sukumar Ghorai <sukumar.ghorai@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We have been using Makefile for well over a decade now, use that name
instead of Kbuild.
Also, while moving the file, add the proper SPDX identifier at the top
of it.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This file is really really old, and doesn't make any sense to keep
around anymore, so just drop it.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a few remaining drivers/usb/ files that do not have SPDX
identifiers in them, all of these are either Kconfig or Makefiles. Add
the correct GPL-2.0 identifier to them to make scanning tools happy.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fixed the checkpatch.pl warning:
WARNING: Missing a blank line after declarations
Added space after declarations to conform to coding style.
Signed-off-by: Bharath Vedartham <linux.bhar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's a fix for the new ftdi gpio support, which failed to take
autosuspend into account, and a patch adding missing SPDX identifiers to
the keyspan headers.
Included are also some new device ids.
All but the SPDX patch have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXEGnxAAKCRALxc3C7H1l
CDWIAP9c3kzZLIxhVLyBpLaBgLQftCov5n0oIfNvbrFak3NZIQEA1R2Lvd/b5wbQ
RS5ZaPzLIeeIUHA0YcavuMjdF3na5QM=
=J9iV
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.0-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.0-rc3
Here's a fix for the new ftdi gpio support, which failed to take
autosuspend into account, and a patch adding missing SPDX identifiers to
the keyspan headers.
Included are also some new device ids.
All but the SPDX patch have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-5.0-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: keyspan_usa: add proper SPDX lines for .h files
USB: serial: pl2303: add new PID to support PL2303TB
USB: serial: ftdi_sio: fix GPIO not working in autosuspend
USB: serial: simple: add Motorola Tetra TPG2200 device id
The keyspan_usa??msg.h files are under a BSD-3 style license, so
properly label them as such with a SPDX line at the top of the file.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
USB Bluetooth controller QCA ROME (0cf3:e007) sometimes stops working
after S3:
[ 165.110742] Bluetooth: hci0: using NVM file: qca/nvm_usb_00000302.bin
[ 168.432065] Bluetooth: hci0: Failed to send body at 4 of 1953 (-110)
After some experiments, I found that disabling LPM can workaround the
issue.
On some platforms, the USB power is cut during S3, so the driver uses
reset-resume to resume the device. During port resume, LPM gets enabled
twice, by usb_reset_and_verify_device() and usb_port_resume().
Consolidate all checks into new LPM helpers to make sure LPM only gets
enabled once.
Fixes: de68bab4fa ("usb: Don't enable USB 2.0 Link PM by default.”)
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org> # after much soaking
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use new helpers to make LPM enabling/disabling more clear.
This is a preparation to subsequent patch.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org> # after much soaking
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove USB errata checking code from driver. Applicability of erratum
is retrieved by reading corresponding property in device tree.
This property is written during device tree fixup.
Besides, replace spaces with tabs to make code aligned.
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@nxp.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_USB_EHCI_FSL is not dependent on FSL_SOC, it can be built on
non-PPC platforms.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
arm/arm64's io.h doesn't define clrbits32() and clrsetbits_be32(), which
causing compile failure on some Layerscape Platforms (such as LS1021A and
LS2012A which also integrates FSL EHCI controller). So use
ioread32be()/iowrite32be() instead to make it workable on both
powerpc and arm.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The HW can swap the USB differential-pair (D+/D-) for each port
separately. So the USB signals can be re-aligned with a misplaced
USB connector on the PCB.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to Documentation/timers/timers-howto.txt, a driver should
use usleep_range() instead of udelay() on NON-ATOMIC CONTEXT if
"SLEEPING FOR ~USECS OR SMALL MSECS ( 10us - 20ms)".
Since the .hardware_init() and .power_ctrl() will run on NON-ATOMIC
CONTEXT, this patch replaces udelay() with usleep_range().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add this SFR compatible definition for the sam9x60 SoC and manage
its use in ohci-at91.c driver.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One of the more common cases of allocation size calculations is finding the
size of a structure that has a zero-sized array at the end, along with memory
for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can now
use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hub sends hot-plug events to the host trough it's interrupt URB. The
driver takes care of completing the URB and re-submitting it. Completion
errors are handled in the hub_event() work, yet submission errors are
ignored, rendering the device unresponsive. All further events are lost.
It is fairly hard to find this issue in the wild, since you have to time
the USB hot-plug event with the URB submission failure. For instance it
could be the system running out of memory or some malfunction in the USB
controller driver. Nevertheless, it's pretty reasonable to think it'll
happen sometime. One can trigger this issue using eBPF's function
override feature (see BCC's inject.py script).
This patch adds a retry routine to the event of a submission error. The
HUB driver will try to re-submit the URB once every second until it's
successful or the HUB is disconnected.
As some USB subsystems already take care of this issue, the
implementation was inspired from usbhid/hid_core.c's.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Oliver Neukum <oneukum@suse.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch "usb: simplify usbport trigger" together with "leds: triggers:
add device attribute support" caused an regression for the usbport
trigger. it will no longer enumerate any active usb hub ports under the
"ports" directory in the sysfs class directory, if the usb host drivers
are fully initialized before the usbport trigger was loaded.
The reason is that the usbport driver tries to register the sysfs
entries during the activate() callback. And this will fail with -2 /
ENOENT because the patch "leds: triggers: add device attribute support"
made it so that the sysfs "ports" group was only being added after the
activate() callback succeeded.
This version of the patch reverts parts of the "usb: simplify usbport
trigger" patch and restores usbport trigger's functionality.
Fixes: 6f7b0bad88 ("usb: simplify usbport trigger")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During the static checker, "data->usbmisc_data" may be NULL.
Fix it by adding this pointer judgement before using.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The README file ni the drivers/usb/usbip/ directory is not needed
anymore, so just delete it.
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Shuah Khan <shuah@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add new PID to support PL2303TB (TYPE_HX)
Signed-off-by: Charles Yeh <charlesyeh522@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
To clear GINTSTS2_WKUP_ALERT_INT bit in GINTSTS2 register
require to write 1. This bit is implemented as "Write to clear".
Fixes: 187c5298a1 ("usb: dwc2: gadget: Add handler for WkupAlert interrupt")
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There is a bug in the current GPIO code for ftdi_sio: it failed to take USB
autosuspend into account. If the device is in autosuspend, calls to
usb_control_msg() fail with -EHOSTUNREACH. Because the standard value for
autosuspend timeout is usually 2-5 seconds, this made it almost impossible
to use the GPIOs on machines that have USB autosuspend enabled. This patch
fixes the issue by acquiring a PM lock on the device for the duration of
the USB transfers. Tested on an FT231X device.
Signed-off-by: Karoly Pados <pados@pados.hu>
[ johan: simplify code somewhat ]
Fixes: ba93cc7da8 ("USB: serial: ftdi_sio: implement GPIO support for FT-X devices")
Cc: stable <stable@vger.kernel.org> # 4.20
Signed-off-by: Johan Hovold <johan@kernel.org>
The source_sink_alloc_func() function is supposed to return error
pointers on error. The function is called from usb_get_function() which
doesn't check for NULL returns so it would result in an Oops.
Of course, in the current kernel, small allocations always succeed so
this doesn't affect runtime.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Currently the link_state is uninitialized and the default value is 0(U0)
before the first time we start the udc, and after we start the udc then
stop the udc, the link_state will be undefined.
We may have the following warnings if we start the udc again with
an undefined link_state:
WARNING: CPU: 0 PID: 327 at drivers/usb/dwc3/gadget.c:294 dwc3_send_gadget_ep_cmd+0x304/0x308
dwc3 100e0000.hidwc3_0: wakeup failed --> -22
[...]
Call Trace:
[<c010f270>] (unwind_backtrace) from [<c010b3d8>] (show_stack+0x10/0x14)
[<c010b3d8>] (show_stack) from [<c034a4dc>] (dump_stack+0x84/0x98)
[<c034a4dc>] (dump_stack) from [<c0118000>] (__warn+0xe8/0x100)
[<c0118000>] (__warn) from [<c0118050>](warn_slowpath_fmt+0x38/0x48)
[<c0118050>] (warn_slowpath_fmt) from [<c0442ec0>](dwc3_send_gadget_ep_cmd+0x304/0x308)
[<c0442ec0>] (dwc3_send_gadget_ep_cmd) from [<c0445e68>](dwc3_ep0_start_trans+0x48/0xf4)
[<c0445e68>] (dwc3_ep0_start_trans) from [<c0446750>](dwc3_ep0_out_start+0x64/0x80)
[<c0446750>] (dwc3_ep0_out_start) from [<c04451c0>](__dwc3_gadget_start+0x1e0/0x278)
[<c04451c0>] (__dwc3_gadget_start) from [<c04452e0>](dwc3_gadget_start+0x88/0x10c)
[<c04452e0>] (dwc3_gadget_start) from [<c045ee54>](udc_bind_to_driver+0x88/0xbc)
[<c045ee54>] (udc_bind_to_driver) from [<c045f29c>](usb_gadget_probe_driver+0xf8/0x140)
[<c045f29c>] (usb_gadget_probe_driver) from [<bf005424>](gadget_dev_desc_UDC_store+0xac/0xc4 [libcomposite])
[<bf005424>] (gadget_dev_desc_UDC_store [libcomposite]) from[<c023d8e0>] (configfs_write_file+0xd4/0x160)
[<c023d8e0>] (configfs_write_file) from [<c01d51e8>] (__vfs_write+0x1c/0x114)
[<c01d51e8>] (__vfs_write) from [<c01d5ff4>] (vfs_write+0xa4/0x168)
[<c01d5ff4>] (vfs_write) from [<c01d6d40>] (SyS_write+0x3c/0x90)
[<c01d6d40>] (SyS_write) from [<c0107400>] (ret_fast_syscall+0x0/0x3c)
Signed-off-by: Zeng Tao <prime.zeng@hisilicon.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
OUT endpoint requests may somtimes have this flag set when
preparing to be submitted to HW indicating that there is an
additional TRB chained to the request for alignment purposes.
If that request is removed before the controller can execute the
transfer (e.g. ep_dequeue/ep_disable), the request will not go
through the dwc3_gadget_ep_cleanup_completed_request() handler
and will not have its needs_extra_trb flag cleared when
dwc3_gadget_giveback() is called. This same request could be
later requeued for a new transfer that does not require an
extra TRB and if it is successfully completed, the cleanup
and TRB reclamation will incorrectly process the additional TRB
which belongs to the next request, and incorrectly advances the
TRB dequeue pointer, thereby messing up calculation of the next
requeust's actual/remaining count when it completes.
The right thing to do here is to ensure that the flag is cleared
before it is given back to the function driver. A good place
to do that is in dwc3_gadget_del_and_unmap_request().
Fixes: c6267a5163 ("usb: dwc3: gadget: align transfers to wMaxPacketSize")
Cc: stable@vger.kernel.org
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We see dwc3 endpoint stopped by unwanted irq during
suspend resume test, which is caused dwc3 ep can't be started
with error "No Resource".
Here, add synchronize_irq before suspend to sync the
pending IRQ handlers complete.
Signed-off-by: Bo He <bo.he@intel.com>
Signed-off-by: Yu Wang <yu.y.wang@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Here are some small USB driver fixes and quirk updates for 5.0-rc2.
The majority here are some quirks for some storage devices to get them
to work properly. There's also a fix here to resolve the reported
issues with some audio devices that say they are UAC3 compliant, but
really are not.
And a fix up for the MAINTAINERS file to remove a dead url.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXDsQMA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykM2wCgzC1E5NUpoCqPZHaYQ/0LNLm6SaEAoIbebWBo
rl39FeUBmPJLTmKD0pFX
=4K55
-----END PGP SIGNATURE-----
Merge tag 'usb-5.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB driver fixes and quirk updates for 5.0-rc2.
The majority here are some quirks for some storage devices to get them
to work properly. There's also a fix here to resolve the reported
issues with some audio devices that say they are UAC3 compliant, but
really are not.
And a fix up for the MAINTAINERS file to remove a dead url.
All have been in linux-next with no reported issues"
* tag 'usb-5.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: storage: Remove outdated URL from MAINTAINERS
USB: Add USB_QUIRK_DELAY_CTRL_MSG quirk for Corsair K70 RGB
usbcore: Select only first configuration for non-UAC3 compliant devices
USB: storage: add quirk for SMI SM3350
USB: storage: don't insert sane sense for SPC3+ when bad sense specified
usb: cdc-acm: send ZLP for Telit 3G Intel based modems
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kmalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kmalloc(struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Delete tab aligning a statement with the right hand side of a
preceding assignment rather than the left hand side.
Found with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The failure happened when I tried to send up to 96DPs per an interval
for SSP ISOC transations by libusb, this is used to verify SSP ISOC
function of USB3 GEN2 controller, so update it as 96DPs.
(refer usb3.1r1.0 section 8.12.6 Isochronous Transactions)
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two statements that are indented incorrectly and need
to be moved to a new line. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is better to initialize the return value "result" to -ENOMEM
than to 0. And because "result" takes the return value of
usb_parse_configuration() which returns 0 for success, setting
"result" to 0 at before and after of the for loop is unnecessary.
Signed-off-by: Suwan Kim <suwan.kim027@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To match the Corsair Strafe RGB, the Corsair K70 RGB also requires
USB_QUIRK_DELAY_CTRL_MSG to completely resolve boot connection issues
discussed here: https://github.com/ckb-next/ckb-next/issues/42.
Otherwise roughly 1 in 10 boots the keyboard will fail to be detected.
Patch that applied delay control quirk for Corsair Strafe RGB:
cb88a05887 ("usb: quirks: add control message delay for 1b1c:1b20")
Previous K70 RGB patch to add delay-init quirk:
7a1646d922 ("Add delay-init quirk for Corsair K70 RGB keyboards")
Signed-off-by: Jack Stocker <jackstocker.93@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In most of the UAC1 and UAC2 audio devices, the first
configuration is most often the best configuration.
However, with recent patch to support UAC3 configuration,
second configuration was unintentionally chosen for
some of the UAC1/2 devices that had more than one
configuration. This was because of the existing check
after the audio config check which selected any config
which had a non-vendor class. This patch fixes this issue.
Fixes: f13912d3f0 ("usbcore: Select UAC3 configuration for audio if present")
Reported-by: Con Kolivas <kernel@kolivas.org>
Signed-off-by: Saranya Gopal <saranya.gopal@intel.com>
Tested-by: Con Kolivas <kernel@kolivas.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SMI SM3350 USB-UFS bridge controller cannot handle long sense request
correctly and will make the chip refuse to do read/write when requested
long sense.
Add a bad sense quirk for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the code will set US_FL_SANE_SENSE flag unconditionally if
device claims SPC3+, however we should allow US_FL_BAD_SENSE flag to
prevent this behavior, because SMI SM3350 UFS-USB bridge controller,
which claims SPC4, will show strange behavior with 96-byte sense
(put the chip into a wrong state that cannot read/write anything).
Check the presence of US_FL_BAD_SENSE when assuming US_FL_SANE_SENSE on
SPC4+ devices.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Telit 3G Intel based modems require zero packet to be sent if
out data size is equal to the endpoint max packet size.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nobody has actually used the type (VERIFY_READ vs VERIFY_WRITE) argument
of the user address range verification function since we got rid of the
old racy i386-only code to walk page tables by hand.
It existed because the original 80386 would not honor the write protect
bit when in kernel mode, so you had to do COW by hand before doing any
user access. But we haven't supported that in a long time, and these
days the 'type' argument is a purely historical artifact.
A discussion about extending 'user_access_begin()' to do the range
checking resulted this patch, because there is no way we're going to
move the old VERIFY_xyz interface to that model. And it's best done at
the end of the merge window when I've done most of my merges, so let's
just get this done once and for all.
This patch was mostly done with a sed-script, with manual fix-ups for
the cases that weren't of the trivial 'access_ok(VERIFY_xyz' form.
There were a couple of notable cases:
- csky still had the old "verify_area()" name as an alias.
- the iter_iov code had magical hardcoded knowledge of the actual
values of VERIFY_{READ,WRITE} (not that they mattered, since nothing
really used it)
- microblaze used the type argument for a debug printout
but other than those oddities this should be a total no-op patch.
I tried to fix up all architectures, did fairly extensive grepping for
access_ok() uses, and the changes are trivial, but I may have missed
something. Any missed conversion should be trivially fixable, though.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Including (in no particular order):
- Page table code for AMD IOMMU now supports large pages where
smaller page-sizes were mapped before. VFIO had to work around
that in the past and I included a patch to remove it (acked by
Alex Williamson)
- Patches to unmodularize a couple of IOMMU drivers that would
never work as modules anyway.
- Work to unify the the iommu-related pointers in
'struct device' into one pointer. This work is not finished
yet, but will probably be in the next cycle.
- NUMA aware allocation in iommu-dma code
- Support for r8a774a1 and r8a774c0 in the Renesas IOMMU driver
- Scalable mode support for the Intel VT-d driver
- PM runtime improvements for the ARM-SMMU driver
- Support for the QCOM-SMMUv2 IOMMU hardware from Qualcom
- Various smaller fixes and improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=DT9A
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- Page table code for AMD IOMMU now supports large pages where smaller
page-sizes were mapped before. VFIO had to work around that in the
past and I included a patch to remove it (acked by Alex Williamson)
- Patches to unmodularize a couple of IOMMU drivers that would never
work as modules anyway.
- Work to unify the the iommu-related pointers in 'struct device' into
one pointer. This work is not finished yet, but will probably be in
the next cycle.
- NUMA aware allocation in iommu-dma code
- Support for r8a774a1 and r8a774c0 in the Renesas IOMMU driver
- Scalable mode support for the Intel VT-d driver
- PM runtime improvements for the ARM-SMMU driver
- Support for the QCOM-SMMUv2 IOMMU hardware from Qualcom
- Various smaller fixes and improvements
* tag 'iommu-updates-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (78 commits)
iommu: Check for iommu_ops == NULL in iommu_probe_device()
ACPI/IORT: Don't call iommu_ops->add_device directly
iommu/of: Don't call iommu_ops->add_device directly
iommu: Consolitate ->add/remove_device() calls
iommu/sysfs: Rename iommu_release_device()
dmaengine: sh: rcar-dmac: Use device_iommu_mapped()
xhci: Use device_iommu_mapped()
powerpc/iommu: Use device_iommu_mapped()
ACPI/IORT: Use device_iommu_mapped()
iommu/of: Use device_iommu_mapped()
driver core: Introduce device_iommu_mapped() function
iommu/tegra: Use helper functions to access dev->iommu_fwspec
iommu/qcom: Use helper functions to access dev->iommu_fwspec
iommu/of: Use helper functions to access dev->iommu_fwspec
iommu/mediatek: Use helper functions to access dev->iommu_fwspec
iommu/ipmmu-vmsa: Use helper functions to access dev->iommu_fwspec
iommu/dma: Use helper functions to access dev->iommu_fwspec
iommu/arm-smmu: Use helper functions to access dev->iommu_fwspec
ACPI/IORT: Use helper functions to access dev->iommu_fwspec
iommu: Introduce wrappers around dev->iommu_fwspec
...
Here is the big set of USB and PHY driver patches for 4.21-rc1.
All of the usual bits are in here:
- loads of USB gadget driver updates and additions
- new device ids
- phy driver updates
- xhci reworks and new features
- typec updates
Full details are in the shortlog.
All of these have been in linux-next for a long time with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXCYxNA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yl4pQCfaQBjMxPpp6TVcHANZ/O+zE3NH/wAoL11p3IB
KUq8v9pmcHO8sW5TWOJw
=iYGf
-----END PGP SIGNATURE-----
Merge tag 'usb-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big set of USB and PHY driver patches for 4.21-rc1.
All of the usual bits are in here:
- loads of USB gadget driver updates and additions
- new device ids
- phy driver updates
- xhci reworks and new features
- typec updates
Full details are in the shortlog.
All of these have been in linux-next for a long time with no reported
issues"
* tag 'usb-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (142 commits)
USB: serial: option: add Fibocom NL678 series
cdc-acm: fix abnormal DATA RX issue for Mediatek Preloader.
usb: r8a66597: Fix a possible concurrency use-after-free bug in r8a66597_endpoint_disable()
usb: typec: tcpm: Extend the matching rules on PPS APDO selection
usb: typec: Improve Alt Mode documentation
usb: musb: dsps: fix runtime pm for peripheral mode
usb: musb: dsps: fix otg state machine
USB: serial: pl2303: add ids for Hewlett-Packard HP POS pole displays
usb: renesas_usbhs: add support for RZ/G2E
usb: ehci-omap: Fix deferred probe for phy handling
usb: roles: Add a description for the class to Kconfig
usb: renesas_usbhs: mark PM functions as __maybe_unused
usb: core: Remove unnecessary memset()
usb: host: isp1362-hcd: convert to DEFINE_SHOW_ATTRIBUTE
phy: qcom-qmp: Expose provided clocks to DT
dt-bindings: phy-qcom-qmp: Move #clock-cells to child
phy: qcom-qmp: Utilize fully-specified DT registers
dt-bindings: phy-qcom-qmp: Fix register underspecification
phy: ti: fix semicolon.cocci warnings
phy: dphy: Add configuration helpers
...
This is mostly update of the usual drivers: smarpqi, lpfc, qedi,
megaraid_sas, libsas, zfcp, mpt3sas, hisi_sas. Additionally, we have
a pile of annotation, unused variable and minor updates. The big API
change is the updates for Christoph's DMA rework which include
removing the DISABLE_CLUSTERING flag. And finally there are a couple
of target tree updates.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXCEUNiYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishdjKAP9vrTTv
qFaYmAoRSbPq9ZiixaXLMy0K/6o76Uay0gnBqgD/fgn3jg/KQ6alNaCjmfeV3wAj
u1j3H7tha9j1it+4pUw=
=GDa+
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: smarpqi, lpfc, qedi,
megaraid_sas, libsas, zfcp, mpt3sas, hisi_sas.
Additionally, we have a pile of annotation, unused variable and minor
updates.
The big API change is the updates for Christoph's DMA rework which
include removing the DISABLE_CLUSTERING flag.
And finally there are a couple of target tree updates"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (259 commits)
scsi: isci: request: mark expected switch fall-through
scsi: isci: remote_node_context: mark expected switch fall-throughs
scsi: isci: remote_device: Mark expected switch fall-throughs
scsi: isci: phy: Mark expected switch fall-through
scsi: iscsi: Capture iscsi debug messages using tracepoints
scsi: myrb: Mark expected switch fall-throughs
scsi: megaraid: fix out-of-bound array accesses
scsi: mpt3sas: mpt3sas_scsih: Mark expected switch fall-through
scsi: fcoe: remove set but not used variable 'port'
scsi: smartpqi: call pqi_free_interrupts() in pqi_shutdown()
scsi: smartpqi: fix build warnings
scsi: smartpqi: update driver version
scsi: smartpqi: add ofa support
scsi: smartpqi: increase fw status register read timeout
scsi: smartpqi: bump driver version
scsi: smartpqi: add smp_utils support
scsi: smartpqi: correct lun reset issues
scsi: smartpqi: correct volume status
scsi: smartpqi: do not offline disks for transient did no connect conditions
scsi: smartpqi: allow for larger raid maps
...
Pull crypto updates from Herbert Xu:
"API:
- Add 1472-byte test to tcrypt for IPsec
- Reintroduced crypto stats interface with numerous changes
- Support incremental algorithm dumps
Algorithms:
- Add xchacha12/20
- Add nhpoly1305
- Add adiantum
- Add streebog hash
- Mark cts(cbc(aes)) as FIPS allowed
Drivers:
- Improve performance of arm64/chacha20
- Improve performance of x86/chacha20
- Add NEON-accelerated nhpoly1305
- Add SSE2 accelerated nhpoly1305
- Add AVX2 accelerated nhpoly1305
- Add support for 192/256-bit keys in gcmaes AVX
- Add SG support in gcmaes AVX
- ESN for inline IPsec tx in chcr
- Add support for CryptoCell 703 in ccree
- Add support for CryptoCell 713 in ccree
- Add SM4 support in ccree
- Add SM3 support in ccree
- Add support for chacha20 in caam/qi2
- Add support for chacha20 + poly1305 in caam/jr
- Add support for chacha20 + poly1305 in caam/qi2
- Add AEAD cipher support in cavium/nitrox"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (130 commits)
crypto: skcipher - remove remnants of internal IV generators
crypto: cavium/nitrox - Fix build with !CONFIG_DEBUG_FS
crypto: salsa20-generic - don't unnecessarily use atomic walk
crypto: skcipher - add might_sleep() to skcipher_walk_virt()
crypto: x86/chacha - avoid sleeping under kernel_fpu_begin()
crypto: cavium/nitrox - Added AEAD cipher support
crypto: mxc-scc - fix build warnings on ARM64
crypto: api - document missing stats member
crypto: user - remove unused dump functions
crypto: chelsio - Fix wrong error counter increments
crypto: chelsio - Reset counters on cxgb4 Detach
crypto: chelsio - Handle PCI shutdown event
crypto: chelsio - cleanup:send addr as value in function argument
crypto: chelsio - Use same value for both channel in single WR
crypto: chelsio - Swap location of AAD and IV sent in WR
crypto: chelsio - remove set but not used variable 'kctx_len'
crypto: ux500 - Use proper enum in hash_set_dma_transfer
crypto: ux500 - Use proper enum in cryp_set_dma_transfer
crypto: aesni - Add scatter/gather avx stubs, and use them in C
crypto: aesni - Introduce partial block macro
..
Pull networking updates from David Miller:
1) New ipset extensions for matching on destination MAC addresses, from
Stefano Brivio.
2) Add ipv4 ttl and tos, plus ipv6 flow label and hop limit offloads to
nfp driver. From Stefano Brivio.
3) Implement GRO for plain UDP sockets, from Paolo Abeni.
4) Lots of work from Michał Mirosław to eliminate the VLAN_TAG_PRESENT
bit so that we could support the entire vlan_tci value.
5) Rework the IPSEC policy lookups to better optimize more usecases,
from Florian Westphal.
6) Infrastructure changes eliminating direct manipulation of SKB lists
wherever possible, and to always use the appropriate SKB list
helpers. This work is still ongoing...
7) Lots of PHY driver and state machine improvements and
simplifications, from Heiner Kallweit.
8) Various TSO deferral refinements, from Eric Dumazet.
9) Add ntuple filter support to aquantia driver, from Dmitry Bogdanov.
10) Batch dropping of XDP packets in tuntap, from Jason Wang.
11) Lots of cleanups and improvements to the r8169 driver from Heiner
Kallweit, including support for ->xmit_more. This driver has been
getting some much needed love since he started working on it.
12) Lots of new forwarding selftests from Petr Machata.
13) Enable VXLAN learning in mlxsw driver, from Ido Schimmel.
14) Packed ring support for virtio, from Tiwei Bie.
15) Add new Aquantia AQtion USB driver, from Dmitry Bezrukov.
16) Add XDP support to dpaa2-eth driver, from Ioana Ciocoi Radulescu.
17) Implement coalescing on TCP backlog queue, from Eric Dumazet.
18) Implement carrier change in tun driver, from Nicolas Dichtel.
19) Support msg_zerocopy in UDP, from Willem de Bruijn.
20) Significantly improve garbage collection of neighbor objects when
the table has many PERMANENT entries, from David Ahern.
21) Remove egdev usage from nfp and mlx5, and remove the facility
completely from the tree as it no longer has any users. From Oz
Shlomo and others.
22) Add a NETDEV_PRE_CHANGEADDR so that drivers can veto the change and
therefore abort the operation before the commit phase (which is the
NETDEV_CHANGEADDR event). From Petr Machata.
23) Add indirect call wrappers to avoid retpoline overhead, and use them
in the GRO code paths. From Paolo Abeni.
24) Add support for netlink FDB get operations, from Roopa Prabhu.
25) Support bloom filter in mlxsw driver, from Nir Dotan.
26) Add SKB extension infrastructure. This consolidates the handling of
the auxiliary SKB data used by IPSEC and bridge netfilter, and is
designed to support the needs to MPTCP which could be integrated in
the future.
27) Lots of XDP TX optimizations in mlx5 from Tariq Toukan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1845 commits)
net: dccp: fix kernel crash on module load
drivers/net: appletalk/cops: remove redundant if statement and mask
bnx2x: Fix NULL pointer dereference in bnx2x_del_all_vlans() on some hw
net/net_namespace: Check the return value of register_pernet_subsys()
net/netlink_compat: Fix a missing check of nla_parse_nested
ieee802154: lowpan_header_create check must check daddr
net/mlx4_core: drop useless LIST_HEAD
mlxsw: spectrum: drop useless LIST_HEAD
net/mlx5e: drop useless LIST_HEAD
iptunnel: Set tun_flags in the iptunnel_metadata_reply from src
net/mlx5e: fix semicolon.cocci warnings
staging: octeon: fix build failure with XFRM enabled
net: Revert recent Spectre-v1 patches.
can: af_can: Fix Spectre v1 vulnerability
packet: validate address length if non-zero
nfc: af_nfc: Fix Spectre v1 vulnerability
phonet: af_phonet: Fix Spectre v1 vulnerability
net: core: Fix Spectre v1 vulnerability
net: minor cleanup in skb_ext_add()
net: drop the unused helper skb_ext_get()
...
The USB Power Delivery discrete components now can be enumerated by
i2c-multi-instantiate driver via several resources under single ACPI
device node (ACPI ID is INT3515).
Touchscreen support is added for the Mediacom Flexbook Edge 11.
Mellanox driver got fixed due to updates in their firmware.
The power management stub driver for AtomISP v2 is fixed in order to support
Intel Baytrail SoCs where same quirk is needed for S0ix to work.
Special key handling has been fixed for Favorites hotkey on Thinkpad, and
Screen LOCK on ASUS.
Ideapad Yoga 2 13 has no HW rfkill switch, thus, driver has been updated
to support this.
Few cleanups related to debugfs have been made in Intel IPS and
Intel PMC drivers. Besides that Intel PMC has been extended
to show more detailed information about Latency Tolerance.
The following is an automated git shortlog grouped by driver:
ACPI / scan:
- Create platform device for INT3515 ACPI nodes
Add the VLV ISP PCI ID to atomisp2_pm:
- Add the VLV ISP PCI ID to atomisp2_pm
asus-nb-wmi:
- Drop mapping of 0x33 and 0x34 scan codes
- Map 0x35 to KEY_SCREENLOCK
asus-wmi:
- Tell the EC the OS will handle the display off hotkey
dell-laptop:
- Mark expected switch fall-throughs
Documentation/ABI:
- Add new attribute for mlxreg-io sysfs interfaces
Fix config space access for intel_atomisp2_pm:
- Fix config space access for intel_atomisp2_pm
i2c:
- acpi: Introduce i2c_acpi_get_i2c_resource() helper
- acpi: Use ACPI_FAILURE instead of !ACPI_SUCCESS
- acpi: Return error pointers from i2c_acpi_new_device()
i2c-multi-instantiate:
- Allow to have same slaves
- Introduce IOAPIC IRQ support
- Distinguish IRQ resource type
- Count I2cSerialBus() resources
- Get rid of obsolete conditional
- Defer probe when no adapter found
- Accept errors of i2c_acpi_new_device()
ideapad-laptop:
- Add Yoga 2 13 to no_hw_rfkill list
iio:
- inv_mpu6050: Use i2c_acpi_get_i2c_resource() helper
intel_cht_int33fe:
- Get rid of obsolete conditional
- Accept errors of i2c_acpi_new_device()
- Remove duplicate NULL check
intel_ips:
- Convert to use DEFINE_SHOW_ATTRIBUTE macro
- Remove never happen condition
- NULL check before some freeing functions is not needed
- remove unnecessary checks in ips_debugfs_init
intel_pmc_core:
- convert to DEFINE_SHOW_ATTRIBUTE
- Decode Snoop / Non Snoop LTR
- Fix LTR IGNORE Max offset
- Show Latency Tolerance info
intel_telemetry:
- convert to DEFINE_SHOW_ATTRIBUTE
mlx-platform:
- Convert to use SPDX identifier
- Allow mlxreg-io driver activation for new systems
- Fix LED configuration
- Fix tachometer registers
- Rename new systems product names
- Add definitions for new registers
thinkpad_acpi:
- Cleanup quirks macros
- Change the keymap for Favorites hotkey
touchscreen_dmi:
- Add info for the Mediacom Flexbook Edge 11
-----BEGIN PGP SIGNATURE-----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=kYH6
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.21-1' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver updates from Andy Shevchenko:
- The USB Power Delivery discrete components now can be enumerated by
i2c-multi-instantiate driver via several resources under single ACPI
device node (ACPI ID is INT3515).
- Touchscreen support is added for the Mediacom Flexbook Edge 11.
- Mellanox driver got fixed due to updates in their firmware.
- The power management stub driver for AtomISP v2 is fixed in order to
support Intel Baytrail SoCs where same quirk is needed for S0ix to
work.
- Special key handling has been fixed for Favorites hotkey on Thinkpad,
and Screen LOCK on ASUS.
- Ideapad Yoga 2 13 has no HW rfkill switch, thus, driver has been
updated to support this.
- Few cleanups related to debugfs have been made in Intel IPS and Intel
PMC drivers. Besides that Intel PMC has been extended to show more
detailed information about Latency Tolerance
* tag 'platform-drivers-x86-v4.21-1' of git://git.infradead.org/linux-platform-drivers-x86: (41 commits)
platform/x86: mlx-platform: Convert to use SPDX identifier
Documentation/ABI: Add new attribute for mlxreg-io sysfs interfaces
platform/x86: mlx-platform: Allow mlxreg-io driver activation for new systems
platform/x86: mlx-platform: Fix LED configuration
platform/x86: mlx-platform: Fix tachometer registers
platform/x86: mlx-platform: Rename new systems product names
platform/x86: mlx-platform: Add definitions for new registers
platform/x86: intel_telemetry: convert to DEFINE_SHOW_ATTRIBUTE
platform/x86: intel_pmc_core: convert to DEFINE_SHOW_ATTRIBUTE
platform/x86: thinkpad_acpi: Cleanup quirks macros
platform/x86: touchscreen_dmi: Add info for the Mediacom Flexbook Edge 11
platform/x86: Fix config space access for intel_atomisp2_pm
platform/x86: Add the VLV ISP PCI ID to atomisp2_pm
platform/x86: intel_ips: Convert to use DEFINE_SHOW_ATTRIBUTE macro
platform/x86: intel_ips: Remove never happen condition
platform/x86: intel_ips: NULL check before some freeing functions is not needed
platform/x86: intel_ips: remove unnecessary checks in ips_debugfs_init
iio: inv_mpu6050: Use i2c_acpi_get_i2c_resource() helper
ACPI / scan: Create platform device for INT3515 ACPI nodes
platform/x86: i2c-multi-instantiate: Allow to have same slaves
...
Here are the USB-serial updates for 4.21-rc1, including:
- support for mos7840 3-port devices
- improved ftdi baud-rate divisor calculations
- support for a new class of f81534 devices
Included are also various clean ups and some new pl2303 device ids.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXBva9AAKCRALxc3C7H1l
CP6XAQClpmmKj59AiAJK+hlWIbNpznPUUrkGHS7mFyuWkDrllQEAsK2IofNWbs9y
g0ot/v4UgUVZHySGl5yYoV4A0uKJdAQ=
=oyPx
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.21-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 4.21-rc1
Here are the USB-serial updates for 4.21-rc1, including:
- support for mos7840 3-port devices
- improved ftdi baud-rate divisor calculations
- support for a new class of f81534 devices
Included are also various clean ups and some new pl2303 device ids.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-4.21-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: pl2303: add ids for Hewlett-Packard HP POS pole displays
USB: serial: mos7840: remove set but not used variables 'number, serial'
USB: serial: mos7840: add a product ID for the new product
USB: serial: mos7840: clean up register handling
USB: serial: ftdi_sio: use rounding when calculating baud rate divisors
USB: serial: f81534: fix reading old/new IC config
USB: serial: mos7840: remove set but not used variables 'st, data1, iflag'
USB: serial: quatech2: remove set but not used variable 'port_priv'
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
Mediatek Preloader is a proprietary embedded boot loader for loading
Little Kernel and Linux into device DRAM.
This boot loader also handle firmware update. Mediatek Preloader will be
enumerated as a virtual COM port when the device is connected to Windows
or Linux OS via CDC-ACM class driver. When the USB enumeration has been
done, Mediatek Preloader will send out handshake command "READY" to PC
actively instead of waiting command from the download tool.
Since Linux 4.12, the commit "tty: reset termios state on device
registration" (93857edd98) causes Mediatek
Preloader receiving some abnoraml command like "READYXX" as it sent.
This will be recognized as an incorrect response. The behavior change
also causes the download handshake fail. This change only affects
subsequent connects if the reconnected device happens to get the same minor
number.
By disabling the ECHO termios flag could avoid this problem. However, it
cannot be done by user space configuration when download tool open
/dev/ttyACM0. This is because the device running Mediatek Preloader will
send handshake command "READY" immediately once the CDC-ACM driver is
ready.
This patch wants to fix above problem by introducing "DISABLE_ECHO"
property in driver_info. When Mediatek Preloader is connected, the
CDC-ACM driver could disable ECHO flag in termios to avoid the problem.
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Cc: stable@vger.kernel.org
Reviewed-by: Johan Hovold <johan@kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function r8a66597_endpoint_disable() and r8a66597_urb_enqueue() may
be concurrently executed.
The two functions both access a possible shared variable "hep->hcpriv".
This shared variable is freed by r8a66597_endpoint_disable() via the
call path:
r8a66597_endpoint_disable
kfree(hep->hcpriv) (line 1995 in Linux-4.19)
This variable is read by r8a66597_urb_enqueue() via the call path:
r8a66597_urb_enqueue
spin_lock_irqsave(&r8a66597->lock)
init_pipe_info
enable_r8a66597_pipe
pipe = hep->hcpriv (line 802 in Linux-4.19)
The read operation is protected by a spinlock, but the free operation
is not protected by this spinlock, thus a concurrency use-after-free bug
may occur.
To fix this bug, the spin-lock and spin-unlock function calls in
r8a66597_endpoint_disable() are moved to protect the free operation.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current matching rules ensure that the voltage range of selected Source
Capability is entirely within the range defined in one of the Sink
Capabilities. This is reasonable but not practical because Sink may not
support wide range of voltage when sinking power while Source could
advertise its capabilities in relatively wider range. For example, a
Source PDO advertising 3.3V-11V@3A (9V Prog of Fixed Nominal Voltage)
will not be selected if the Sink requires 5V-12V@3A PPS power. However,
the Sink could work well if the requested voltage range in RDOs is
5V-11V@3A.
Currently accepted:
|--------- source -----|
|----------- sink ---------------|
Currently not accepted:
|--------- source -----|
|----------- sink ---------------|
|--------- source -----|
|----------- sink ---------------|
|--------- source -----------------|
|------ sink -------|
To improve the usability, change the matching rules to what listed
below:
a. The Source PDO is selectable if any portion of the voltage range
overlaps one of the Sink PDO's voltage range.
b. The maximum operational voltage will be the lower one between the
selected Source PDO and the matching Sink PDO.
c. The maximum power will be the maximum operational voltage times the
maximum current defined in the selected Source PDO
d. Select the Source PDO with the highest maximum power
Signed-off-by: Kyle Tso <kyletso@google.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The same effects can be achieved by setting the dma_boundary to
PAGE_SIZE - 1 and the max_segment_size to PAGE_SIZE, so shift those
settings into the drivers. Note that in many cases the setting might
be bogus, but this keeps the status quo.
[mkp: fix myrs and myrb]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Most SCSI drivers want to enable "clustering", that is merging of
segments so that they might span more than a single page. Remove the
ENABLE_CLUSTERING define, and require drivers to explicitly set
DISABLE_CLUSTERING to disable this feature.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A few drivers were not setting the use_clustering flag at all and thus
default to disable. Fix them up to explicitly set this field in
preparation for additional cleanups.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since the runtime PM support was added in musb, dsps relies on the timer
calling otg_timer() to activate the usb subsystem. However the driver
doesn't enable the timer for peripheral port, then the peripheral port is
unable to be enumerated by a host if the other usb port is disabled or in
peripheral mode too.
So let's start the timer for peripheral port too.
Fixes: ea2f35c01d ("usb: musb: Fix sleeping function called from invalid context for hdrc glue")
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to lack of ID pin interrupt event on AM335x devices, the musb dsps
driver uses polling to detect usb device attach for dual-role port.
But in the case if a micro-A cable adapter is attached without a USB device
attached to the cable, the musb state machine gets stuck in a_wait_vrise
state waiting for the MUSB_CONNECT interrupt which won't happen due to the
usb device is not attached. The state is stuck in a_wait_vrise even after
the micro-A cable is detached, which could cause VBUS retention if then the
dual-role port is attached to a host port.
To fix the problem, make a_wait_vrise as a transient state, then move the
state to either a_wait_bcon for host port or a_idle state for dual-role
port, if no usb device is attached to the port.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add device ids to pl2303 for the HP POS pole displays:
LM920: 03f0:026b
TD620: 03f0:0956
LD960TA: 03f0:4439
LD220TA: 03f0:4349
LM940: 03f0:5039
Signed-off-by: Scott Chen <scott@labau.com.tw>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Move Synopsys HAPS platform device IDs to pci_ids.h so that both
drivers/pci/quirks.c and dwc3-haps driver can reference these IDs.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
As commented in the struct's definition there shouldn't be anything
underneath its 'priv[0]' member as it would break some macros.
The patch converts the broken_suspend into a bit-field and relocates it
next to to the rest of bit-fields.
Fixes: a7d57abcc8 ("xhci: workaround CSS timeout on AMD SNPS 3.0 xHC")
Reported-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HS-USB found in RZ/G2E (a.k.a. r8a774c0) is very similar to the
one found in R-Car E3 (a.k.a. r8a77990), as it needs to release
the PLL reset by the UGCTRL register like R-Car E3, therefore add
r8a774c0 support in a similar fashion to what was done for the
r8a77990.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PHY model is being used on omap5 platforms even if port mode
is not OMAP_EHCI_PORT_MODE_PHY. So don't guess if PHY is required
or not based on PHY mode.
If PHY is provided in device tree, it must be required. So, if
devm_usb_get_phy_by_phandle() gives us an error code other
than -ENODEV (no PHY) then error out.
This fixes USB Ethernet on omap5-uevm if PHY happens to
probe after EHCI thus causing a -EPROBE_DEFER.
Cc: Johan Hovold <johan@kernel.org>
Cc: Ladislav Michl <ladis@linux-mips.org>
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
That makes the USB role switch support option visible and
selectable for the user. The class driver is also moved to
drivers/usb/roles/ directory.
This will fix an issue that we have with the Intel USB role
switch driver on systems that don't have USB Type-C connectors:
Intel USB role switch driver depends on the USB role switch
class as it should, but since there was no way for the user
to enable the USB role switch class, there was also no way
to select that driver. USB Type-C drivers select the USB
role switch class which makes the Intel USB role switch
driver available and therefore hides the problem.
So in practice Intel USB role switch driver was depending on
USB Type-C drivers.
Fixes: f6fb9ec02b ("usb: roles: Add Intel xHCI USB role switch driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Add the HSIC support for imx
-----BEGIN PGP SIGNATURE-----
iQEwBAABCAAaBQJcF1bIExxwZXRlci5jaGVuQG54cC5jb20ACgkQSFkpgVDWcbv1
Xgf/RIlKRdLOiO0wCJWkmiHRIU/YE0V6QNwhMKCUK2PfAqLI3px/a/uOam7U8ysn
6TvrUYxy/V7yBDCw6bR8bbJeP5gFjZPEnqd4RV6YZzP7Zc6FJ/10cLMWWGfB61JV
xqcVzJGjZ/AuU00TDDEeKXnGB4w6iH47x0ywimxlHSEhSUGQEoogopgtlr8JfnWg
bVQ9wr1jkUmkDymVFaHzrYSWVIToejGOB2kNRmhGpxKIUq3Mv/X0Vux50+egNpDK
ikyVo5oIr1cU0nVlAl2lquoTf6F7gRo2GduY9stw2VR6VxUUvd2cj57bJlhiwqPe
3jRiXjWtZKsWEcSpMhaT8ks+Og==
=Q7/x
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
- Improve the over-current handling for imx
- Add the HSIC support for imx
* tag 'usb-ci-v4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
usb: chipidea: imx: allow to configure oc polarity on i.MX25
usb: chipidea: imx: Warn if oc polarity isn't specified
usb: chipidea: imx: support configuring for active low oc signal
doc: usb: ci-hdrc-usb2: Add pinctrl properties for HSIC pin groups
usb: chipidea: host: override ehci->hub_control
usb: chipidea: imx: add HSIC support
usb: chipidea: add flag for imx hsic implementation
Replace the dev->iommu_group check with a proper function
call that better reprensents its purpose.
Cc: Mathias Nyman <mathias.nyman@intel.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Here are some new modem device ids.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXBPTKwAKCRALxc3C7H1l
CKtnAQCMMhEqKVlPbvWAxEvyx9/1tm7fOaj052HBuYSZL5W0LQEA9mh8A/0+HpBC
lXyfNs77XsOlNjbgctouMgECKv5QKwU=
=RBJX
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.20-rc7' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 4.20-rc7
Here are some new modem device ids.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-4.20-rc7' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Telit LN940 series
USB: serial: option: add Fibocom NL668 series
USB: serial: option: add Simcom SIM7500/SIM7600 (MBIM mode)
USB: serial: option: add GosunCn ZTE WeLink ME3630
USB: serial: option: add HP lt4132
The code to prevent a bus suspend if a USB3 port was still in link training
also reacted to USB2 port polling state.
This caused bus suspend to busyloop in some cases.
USB2 polling state is different from USB3, and should not prevent bus
suspend.
Limit the USB3 link training state check to USB3 root hub ports only.
The origial commit went to stable so this need to be applied there as well
Fixes: 2f31a67f01 ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A follow-up patch will add a notifier type NETDEV_PRE_CHANGEADDR, which
allows vetoing of MAC address changes. One prominent path to that
notification is through dev_set_mac_address(). Therefore give this
function an extack argument, so that it can be packed together with the
notification. Thus a textual reason for rejection (or a warning) can be
communicated back to the user.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without CONFIG_PM, we get a new build warning here:
drivers/usb/renesas_usbhs/common.c:860:12: error: 'usbhsc_resume' defined but not used [-Werror=unused-function]
static int usbhsc_resume(struct device *dev)
^~~~~~~~~~~~~
drivers/usb/renesas_usbhs/common.c:844:12: error: 'usbhsc_suspend' defined but not used [-Werror=unused-function]
static int usbhsc_suspend(struct device *dev)
^~~~~~~~~~~~~~
Fixes: d54d334e75 ("usb: renesas_usbhs: Use SIMPLE_DEV_PM_OPS macro")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
register_root_hub() calls memset() setting usb_dev->bus->devmap.
devicemap to 0 during hcd probe function (usb_hcd_pci_probe). But
in previous function which is also the procedure of usb_hcd_pci_probe(),
usb_bus_init() already initialized bus->devmap calling memset().
Furthermore, register_root_hub() is called only once in kernel.
So, calling memset() which resets usb_bus->devmap.devicemap in
register_root_hub() is redundant.
Signed-off-by: Suwan Kim <suwan.kim027@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So it looks like folks are interested in dwc3 again. Almost 64% of the
changes are in dwc3 this time around with some other bits in gadget
functions and dwc2.
There are two important parts here: a. removal of the waitqueue from
dwc3's dequeue implementation, which will guarantee that gadget
functions can dequeue from any context and; b. better method for
starting isochronous transfers to avoid, as much as possible, missed
isoc frames.
Apart from these, we have the usual set of non-critical fixes and new
features all over the place.
-----BEGIN PGP SIGNATURE-----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=n8VS
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB changes for v4.21
So it looks like folks are interested in dwc3 again. Almost 64% of the
changes are in dwc3 this time around with some other bits in gadget
functions and dwc2.
There are two important parts here: a. removal of the waitqueue from
dwc3's dequeue implementation, which will guarantee that gadget
functions can dequeue from any context and; b. better method for
starting isochronous transfers to avoid, as much as possible, missed
isoc frames.
Apart from these, we have the usual set of non-critical fixes and new
features all over the place.
* tag 'usb-for-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (56 commits)
usb: dwc2: Fix disable all EP's on disconnect
usb: dwc3: gadget: Disable CSP for stream OUT ep
usb: dwc2: disable power_down on Amlogic devices
Revert "usb: dwc3: pci: Use devm functions to get the phy GPIOs"
USB: gadget: udc: s3c2410_udc: convert to DEFINE_SHOW_ATTRIBUTE
usb: mtu3: fix dbginfo in qmu_tx_zlp_error_handler
usb: dwc3: trace: add missing break statement to make compiler happy
usb: dwc3: gadget: Report isoc transfer frame number
usb: gadget: Introduce frame_number to usb_request
usb: renesas_usbhs: Use SIMPLE_DEV_PM_OPS macro
usb: renesas_usbhs: Remove dummy runtime PM callbacks
usb: dwc2: host: use hrtimer for NAK retries
usb: mtu3: clear SOFTCONN when clear USB3_EN if work as HS mode
usb: mtu3: enable SETUPENDISR interrupt
usb: mtu3: fix the issue about SetFeature(U1/U2_Enable)
usb: mtu3: enable hardware remote wakeup from L1 automatically
usb: mtu3: remove QMU checksum
usb/mtu3: power down device ip at setup
usb: dwc2: Disable power down feature on Samsung SoCs
usb: dwc3: Correct the logic for checking TRB full in __dwc3_prepare_one_trb()
...
Disabling all EP's allow to reset EP's to initial state.
Introduced new function dwc2_hsotg_ep_disable_lock() which
before calling dwc2_hsotg_ep_disable() function acquire
hsotg->lock and release on exiting.
From dwc2_hsotg_ep_disable() function removed acquiring
hsotg->lock.
In dwc2_hsotg_core_init_disconnected() function when USB
reset interrupt asserted disabling all ep’s by
dwc2_hsotg_ep_disable() function.
This updates eliminating sparse imbalance warnings.
Reverted changes in dwc2_hostg_disconnect() function.
Introduced new function dwc2_hsotg_ep_disable_lock().
Changed dwc2_hsotg_ep_ops. Now disable point to
dwc2_hsotg_ep_disable_lock() function.
In functions dwc2_hsotg_udc_stop() and dwc2_hsotg_suspend()
dwc2_hsotg_ep_disable() function replaced by
dwc2_hsotg_ep_disable_lock() function.
In dwc2_hsotg_ep_disable() function removed acquiring
of hsotg->lock.
Fixes: dccf1bad4b ("usb: dwc2: Disable all EP's on disconnect")
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Up to now the polarity of the over current pin was hard coded to active
high. Use the already defined device tree properties to configure polarity
on i.MX25, too. In difference to i.MX6/7 use active high behavior if the
polarity is unspecified to keep compatibility to existing device trees.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The polarity of the over current detection pin isn't configured on i.MX6/7
if it's unspecified in the device tree. So the actual configuration depends
on bootloader behavior which is bad.
So encourage users to fix their device tree by issuing a warning in this
case.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The status quo on i.MX6 is that if "over-current-active-high" is
specified in the device tree this is configured as expected. If
the property is missing polarity isn't changed and so the
polarity is kept as setup by the bootloader. Reset default is
active high, so active low can only be used with help by the
bootloader. On i.MX7 it is similar, but there disabling of
over current detection has a similar inconsistency.
This patch introduces a new property that allows to explicitly
configure for active low over current detection and consistently
sets this up. In the absence of an explicit configuration the
bit is kept as is. On i.MX7 over current detection is used unless
disabled in the device tree.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The chipidea controller has some special requirements during
suspend/resume, override common ehci->hub_control to implement
it.
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
To support imx HSIC, there are some special requirement:
- The HSIC pad is 1.2v, it may need to supply from external
- The data/strobe pin needs to be pulled down first, and after
host mode is initialized, the strobe pin needs to be pulled up
- During the USB suspend/resume, special setting is needed
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
NXP (Freecale) imx HSIC design has some special requirements, add
some flags at host code to handle them.
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
In stream mode, when fast-forwarding TRBs, the stream number
is not cleared causing the new stream to not get assigned. So
we don't want controller to carry on transfers when short packet
is received. So disable the CSP for stream capable endpoint.
This is based on the 3.30a Programming guide, where table 3-1
device descriptor structure field definitions says for CSP bit
If this bit is 0, the controller generates an XferComplete event
and remove the stream. So if we keep CSP as 1 then switching between
streams would not happen as in stream mode, when fast-forwarding
TRBs, the stream number is not cleared causing the new stream to not get
assigned.
Signed-off-by: Tejas Joglekar <joglekar@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/usb/serial/mos7840.c: In function 'mos7840_send_cmd_write_baud_rate':
drivers/usb/serial/mos7840.c:1584:16: warning:
variable 'number' set but not used [-Wunused-but-set-variable]
drivers/usb/serial/mos7840.c: In function 'mos7840_change_port_settings':
drivers/usb/serial/mos7840.c:1695:21: warning:
variable 'serial' set but not used [-Wunused-but-set-variable]
'number' never used since introduction in commit 3f5429746d ("USB: Moschip
7840 USB-Serial Driver")
'serial' not used since commit 5833041f1b ("USB: serial: remove unnecessary
reinitialisations of urb->dev")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Disable power_down by setting the parameter to
DWC2_POWER_DOWN_PARAM_NONE. This fixes a problem on various Amlogic
Meson SoCs where USB devices are only recognized when plugged in before
booting Linux. A hot-plugged USB device was not detected even though the
device got power (my USB thumb drive for example has an LED which lit
up).
A similar fix was implemented for Rockchip SoCs in commit c216765d3a
("usb: dwc2: disable power_down on rockchip devices"). That commit
suggests that a change in the dwc2 driver is the cause because the
default value for the "hibernate" parameter (which then got renamed to
"power_down" to support other modes) was changed in the v4.17 merge
window with:
commit 6d23ee9caa ("Merge tag 'usb-for-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-testing").
Cc: <stable@vger.kernel.org> # 4.19
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Suggested-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Refactoring, no functional changes.
But worth mentioning that checking for port link resume state is now behind
a additional port power check.
This is fine as ports can't be in resume state if port power bit is not
set.
xhci spec section 4.19.1.1.6 figure 34 shows that port power bit must be
set for all 'Enable' substates, including U0,U1,U2,U3 (suspended), Resume,
and RExit states.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move U0 link state handing to USB3 and USB2 specific functions
Note that
bus_state->resuming_ports:
bus_state->resume_done[]:
are only used for USB2, and don't need to cleared for USB3 ports
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Group the code where the wPortstatus and wPortChange bits
are set into one place.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mostly refactoring, with the exception that USB_PORT_STAT_L1 link state
is reported if xhci port link is in U2 AND port is powered.
Previously we did not check if the port was powered, but according to
xhci spec 4.19.1.1.6 All the 'Enabled' states, including
USB_PORT_STAT_L1 (U2), U1, U0 and U3 must have Port power bit set.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that each root hub has their own bus_state strucure the
hcd_undex() used to get the correct bus_state strucure is
no longer needed.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the bus_state structure under struct usb_hub.
We need a bus_state strucure for each roothub to keep track of suspend
related info for each port.
Instead of keeping an array of two bus_state structures right under
struct xhci, it makes more sense move them to the xhci_hub structure.
No functional changes.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is introduced for the pre-0.96 xHC controllers, and the driver only
support HW LPM for 1.0 and later controllers.It's not actually used now
and is thought not to be used in the future any more, so just remove it.
Signed-off-by: Zeng Tao <prime.zeng@hisilicon.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 211f658b7b ("usb: dwc3: pci: Use devm functions to get
the phy GPIOs") changed the code to claim the PHY GPIOs permanently
for Intel Baytrail devices.
This causes issues when the actual PHY driver attempts to claim the
same GPIO descriptors. For example, tusb1210 now fails to probe with:
tusb1210: probe of dwc3.0.auto.ulpi failed with error -16 (EBUSY)
dwc3-pci needs to turn on the PHY once before dwc3 is loaded, but
usually the PHY driver will then hold the GPIOs to turn off the
PHY when requested (e.g. during suspend).
To fix the problem, this reverts the commit to restore the old
behavior to put the GPIOs immediately after usage.
Link: https://www.spinics.net/lists/linux-usb/msg174681.html
Cc: stable@vger.kernel.org
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/usb/mtu3/mtu3_qmu.c: In function 'qmu_tx_zlp_error_handler':
drivers/usb/mtu3/mtu3_qmu.c:385:22: warning:
variable 'req' set but not used [-Wunused-but-set-variable]
It seems dbginfo original intention is print 'req' other than 'mreq'
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The missed break statement in the outer switch makes the code fall through
always and thus always same value will be printed.
Besides that, compiler warns about missed fall through marker:
drivers/usb/dwc3/./trace.h: In function ‘trace_raw_output_dwc3_log_trb’:
drivers/usb/dwc3/./trace.h:246:4: warning: this statement may fall through [-Wimplicit-fallthrough=]
switch (pcm) {
^~~~~~
Add the missing break statement to work correctly without compilation
warnings.
Fixes: fa8d965d73 ("usb: dwc3: trace: pretty print high-bandwidth transfers too")
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Here's a fix for a reported USB-console regression in 4.18 which
revealed a long-standing bug in the console implementation.
The patch has been in linux-next over night with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXAlOXAAKCRALxc3C7H1l
COC9AP4jozobKxNIgbmP6LAwz34Zv19qZyhi2hOzM0Less5o+QD+PLKS4yFPErNq
L6jm+cb1RE3rW9bjrbphoT7PvQoa3QM=
=QA9N
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.20-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fix for v4.20-rc6
Here's a fix for a reported USB-console regression in 4.18 which
revealed a long-standing bug in the console implementation.
The patch has been in linux-next over night with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-4.20-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: console: fix reported terminal settings
Don't allow USB3 U1 or U2 if the latency to wake up from the U-state
reaches the service interval for a periodic endpoint.
This is according to xhci 1.1 specification section 4.23.5.2 extra note:
"Software shall ensure that a device is prevented from entering a U-state
where its worst case exit latency approaches the ESIT."
Allowing too long exit latencies for periodic endpoint confuses xHC
internal scheduling, and new devices may fail to enumerate with a
"Not enough bandwidth for new device state" error from the host.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Occasionally AMD SNPS 3.0 xHC does not respond to
CSS when set, also it does not flag anything on SRE and HCE
to point the internal xHC errors on USBSTS register. This stalls
the entire system wide suspend and there is no point in stalling
just because of xHC CSS is not responding.
To work around this problem, if the xHC does not flag
anything on SRE and HCE, we can skip the CSS
timeout and allow the system to continue the suspend. Once the
system resume happens we can internally reset the controller
using XHCI_RESET_ON_RESUME quirk
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Sandeep Singh <Sandeep.Singh@amd.com>
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Cc: <stable@vger.kernel.org>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When reading an extra descriptor, we need to properly check the minimum
and maximum size allowed, to prevent from invalid data being sent by a
device.
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Co-developed-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Hui Peng <benquike@gmail.com>
Signed-off-by: Mathias Payer <mathias.payer@nebelwelt.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB-serial console implementation has never reported the actual
terminal settings used. Despite storing the corresponding cflags in its
struct console, these were never honoured on later tty open() where the
tty termios would be left initialised to the driver defaults.
Unlike the serial console implementation, the USB-serial code calls
subdriver open() already at console setup. While calling set_termios()
and write() before open() looks like it could work for some USB-serial
drivers, others definitely do not expect this, so modelling this after
serial core is going to be intrusive, if at all possible.
Instead, use a (renamed) tty helper to save the termios data used at
console setup so that the tty termios reflects the actual terminal
settings after a subsequent tty open().
Note that the calls to tty_init_termios() (tty_driver_install()) and
tty_save_termios() are serialised using the disconnect mutex.
This specifically fixes a regression that was triggered by a recent
change adding software flow control to the pl2303 driver: a getty trying
to disable flow control while leaving the baud rate unchanged would now
also set the baud rate to the driver default (prior to the flow-control
change this had been a noop).
Fixes: 7041d9c3f0 ("USB: serial: pl2303: add support for tx xon/xoff flow control")
Cc: stable <stable@vger.kernel.org> # 4.18
Cc: Florian Zumbiehl <florz@florz.de>
Reported-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The spinlock was inside the urb completion function which is only
called once per display and is then resubmitted from this function.
There was no other place where this lock was used.
Signed-off-by: Alexander Theissen <alex.theissen@me.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver does allocate a DMA address with usb_alloc_coherent but did
not set the appropriate flag to signal that transfer_dma is set to a
valid value.
Signed-off-by: Alexander Theissen <alex.theissen@me.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some lower volume SanDisk Ultra Flair in 16GB, which the VID:PID is
in 0781:5591, will aggressively request LPM of U1/U2 during runtime,
when using this thumb drive as the OS installation key we found the
device will generate failure during U1 exit path making it dropped
from the USB bus, this causes a corrupted installation in system at
the end.
i.e.,
[ 166.918296] hub 2-0:1.0: state 7 ports 7 chg 0000 evt 0004
[ 166.918327] usb usb2-port2: link state change
[ 166.918337] usb usb2-port2: do warm reset
[ 166.970039] usb usb2-port2: not warm reset yet, waiting 50ms
[ 167.022040] usb usb2-port2: not warm reset yet, waiting 200ms
[ 167.276043] usb usb2-port2: status 02c0, change 0041, 5.0 Gb/s
[ 167.276050] usb 2-2: USB disconnect, device number 2
[ 167.276058] usb 2-2: unregistering device
[ 167.276060] usb 2-2: unregistering interface 2-2:1.0
[ 167.276170] xhci_hcd 0000:00:15.0: shutdown urb ffffa3c7cc695cc0 ep1in-bulk
[ 167.284055] sd 0:0:0:0: [sda] tag#0 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[ 167.284064] sd 0:0:0:0: [sda] tag#0 CDB: Read(10) 28 00 00 33 04 90 00 01 00 00
...
Analyzed the USB trace in the link layer we realized it is because
of the 6-ms timer of tRecoveryConfigurationTimeout which documented
on the USB 3.2 Revision 1.0, the section 7.5.10.4.2 of "Exit from
Recovery.Configuration"; device initiates U1 exit -> Recovery.Active
-> Recovery.Configuration, then the host timer timeout makes the link
transits to eSS.Inactive -> Rx.Detect follows by a Warm Reset.
Interestingly, the other higher volume of SanDisk Ultra Flair sharing
the same VID:PID, such as 64GB, would not request LPM during runtime,
it sticks at U0 always, thus disabling LPM does not affect those thumb
drives at all.
The same odd occures in SanDisk Ultra Fit 16GB, VID:PID in 0781:5583.
Signed-off-by: Harry Pan <harry.pan@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzbot and KASAN found the following invalid-free bug in
port_over_current_notify():
--------------------------------------------------------------------------
BUG: KASAN: double-free or invalid-free in port_over_current_notify
drivers/usb/core/hub.c:5192 [inline]
BUG: KASAN: double-free or invalid-free in port_event
drivers/usb/core/hub.c:5241 [inline]
BUG: KASAN: double-free or invalid-free in hub_event+0xd97/0x4140
drivers/usb/core/hub.c:5384
CPU: 1 PID: 32710 Comm: kworker/1:3 Not tainted 4.20.0-rc3+ #129
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x244/0x39d lib/dump_stack.c:113
print_address_description.cold.7+0x9/0x1ff mm/kasan/report.c:256
kasan_report_invalid_free+0x64/0xa0 mm/kasan/report.c:336
__kasan_slab_free+0x13a/0x150 mm/kasan/kasan.c:501
kasan_slab_free+0xe/0x10 mm/kasan/kasan.c:528
__cache_free mm/slab.c:3498 [inline]
kfree+0xcf/0x230 mm/slab.c:3817
port_over_current_notify drivers/usb/core/hub.c:5192 [inline]
port_event drivers/usb/core/hub.c:5241 [inline]
hub_event+0xd97/0x4140 drivers/usb/core/hub.c:5384
process_one_work+0xc90/0x1c40 kernel/workqueue.c:2153
worker_thread+0x17f/0x1390 kernel/workqueue.c:2296
kthread+0x35a/0x440 kernel/kthread.c:246
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352
--------------------------------------------------------------------------
The problem is caused by use of a static array to store
environment-string pointers. When the routine is called by multiple
threads concurrently, the pointers from one thread can overwrite those
from another.
The solution is to use an ordinary automatic array instead of a static
array.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: syzbot+98881958e1410ec7e53c@syzkaller.appspotmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add another Apple Cinema Display to the list of supported displays.
Signed-off-by: Alexander Theissen <alex.theissen@me.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we are going to use the same in Designware USB 3 driver,
rename the property to be consistent across the drivers.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement the new frame_number API to report the isochronous interval
frame number. This patch checks and reports the interval in which the
isoc transfer was transmitted or received via the Isoc-First TRB SOF
number field.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When the controller supports SS mode, but works as HS mode, the
SOFTCONN will not be cleared automatically when clear USB3_EN
by default, this cause an issue that can't disconnect from host,
so clear SOFTCONN when clear USB3_EN when the class driver want
to disable the D+ pullup.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the controller receives a new SETUP during SETUP data stage,
and will generate SETUPENDISR interrupt, the driver should abort
the current SETUP command and process the new one.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the issue: device doesn't accept LGO_U1/U2:
1. set SW_U1/U2_ACCEPT_ENABLE to eanble controller to accept LGO_U1/U2
by default;
2. enable/disable controller to initiate requests for transition into
U1/U2 by SW_U1/U2_REQUEST_ENABLE instead of SW_U1/U2_ACCEPT_ENABLE;
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable hardware remote wakeup from L1 automatically based on the FIFO
status, instead of manual way.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The QMU checksum calculation is redundant, mostly used by debug,
so remove it here.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Originally, when dr_mode is USB_DR_MODE_HOST, it didn't power down device ip,
so host ip sleep will fail at ssusb_host_disable.
Power down device ip at ssusb_host_setup.
Signed-off-by: Hsin-Yi, Wang <hsinyi@chromium.org>
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Modify the wait delay utilize the high resolution timer API to allow for
more precisely scheduled callbacks.
A previous commit added a 1ms retry delay after multiple consecutive
NAKed transactions using jiffies. On systems with a low timer interrupt
frequency, this delay may be significantly longer than specified,
resulting in misbehavior with some USB devices.
This scenario was reached on a Raspberry Pi 3B with a Macally FDD-USB
floppy drive (identified as 0424:0fdc Standard Microsystems Corp.
Floppy, based on the USB97CFDC USB FDC). With the relay delay, the drive
would be unable to mount a disk, replying with NAKs until the device was
reset.
Using ktime, the delta between starting the timer (in dwc2_hcd_qh_add)
and the callback function can be determined. With the original delay
implementation, this value was consistently approximately 12ms. (output
in us).
<idle>-0 [000] ..s. 1600.559974: dwc2_wait_timer_fn: wait_timer delta: 11976
<idle>-0 [000] ..s. 1600.571974: dwc2_wait_timer_fn: wait_timer delta: 11977
<idle>-0 [000] ..s. 1600.583974: dwc2_wait_timer_fn: wait_timer delta: 11976
<idle>-0 [000] ..s. 1600.595974: dwc2_wait_timer_fn: wait_timer delta: 11977
After converting the relay delay to using a higher resolution timer, the
delay was much closer to 1ms.
<idle>-0 [000] d.h. 1956.553017: dwc2_wait_timer_fn: wait_timer delta: 1002
<idle>-0 [000] d.h. 1956.554114: dwc2_wait_timer_fn: wait_timer delta: 1002
<idle>-0 [000] d.h. 1957.542660: dwc2_wait_timer_fn: wait_timer delta: 1004
<idle>-0 [000] d.h. 1957.543701: dwc2_wait_timer_fn: wait_timer delta: 1002
The floppy drive operates properly with delays up to approximately 5ms,
and sends NAKs for any delays that are longer.
Fixes: 38d2b5fb75 ("usb: dwc2: host: Don't retry NAKed transactions right away")
Cc: <stable@vger.kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Terin Stock <terin@terinstock.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When initializing a hub we want to give a USB3 port in link training
the same debounce delay time before autosuspening the hub as already
trained, connected enabled ports.
USB3 ports won't reach the enabled state with "current connect status" and
"connect status change" bits set until the USB3 link training finishes.
Catching the port in link training (polling) and adding the debounce delay
prevents unnecessary failed attempts to autosuspend the hub.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the controller supports SS mode, but works as HS mode, the
SOFTCONN will not be cleared automatically when clear USB3_EN
by default, this cause an issue that can't disconnect from host,
so clear SOFTCONN when clear USB3_EN when the class driver want
to disable the D+ pullup.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If the controller receives a new SETUP during SETUP data stage,
and will generate SETUPENDISR interrupt, the driver should abort
the current SETUP command and process the new one.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix the issue: device doesn't accept LGO_U1/U2:
1. set SW_U1/U2_ACCEPT_ENABLE to eanble controller to accept LGO_U1/U2
by default;
2. enable/disable controller to initiate requests for transition into
U1/U2 by SW_U1/U2_REQUEST_ENABLE instead of SW_U1/U2_ACCEPT_ENABLE;
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Enable hardware remote wakeup from L1 automatically based on the FIFO
status, instead of manual way.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The QMU checksum calculation is redundant, mostly used by debug,
so remove it here.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Originally, when dr_mode is USB_DR_MODE_HOST, it didn't power down device ip,
so host ip sleep will fail at ssusb_host_disable.
Power down device ip at ssusb_host_setup.
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Hsin-Yi, Wang <hsinyi@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Power down feature of DWC2 module integrated in Samsung SoCs doesn't work
properly or needs some additional handling in PHY or SoC glue layer, so
disable it for now. Without disabling power down, DWC2 causes random memory
trashes and fails enumeration if there is no USB link to host on driver
probe.
Fixes: 03ea6d6e9e ("usb: dwc2: Enable power down")
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Availability of TRB's is calculated using dwc3_calc_trbs_left(), which
determines total available TRB's based on the HWO bit set in a TRB.
In the present code, __dwc3_prepare_one_trb() is called with a TRB which
needs to be prepared for transfer. This __dwc3_prepare_one_trb() calls
dwc3_calc_trbs_left() to determine total available TRBs and set IOC bit
if the total available TRBs are zero. Since the present working TRB (which
is passed as an argument to __dwc3_prepare_one_trb() ) doesn't yet have
the HWO bit set before calling dwc3_calc_trbs_left(), there are chances
that dwc3_calc_trbs_left() wrongly calculates this present working TRB
as free(since the HWO bit is not yet set) and returns the total available
TRBs as greater than zero (including the present working TRB). This could
be a problem.
This patch corrects the above mentioned problem in __dwc3_prepare_one_trb()
by increementing the dep->trb_enqueue at the last (after preparing the TRB)
instead of increementing at the start and setting the IOC bit only if the
total available TRBs returned by dwc3_calc_trbs_left() is 1 . Since we are
increementing the dep->trb_enqueue at the last, the present working TRB is
also considered as available by dwc3_calc_trbs_left() and non zero value is
returned . So, according to the modified logic, when the total available
TRBs is equal to 1 that means the total available TRBs in the pool are 0.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Reviewed-by: Thinh Nguyen <thinhn@synopsys.com>
Tested-by: Tejas Joglekar <tejas.joglekar@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The stream capable endpoints require stream id to be given
when issuing START TRANSFER. While issuing no-op trb the
stream id is not yet known, so don't issue no-op trb's on
stream capable endpoints.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For stream capable endpoints, stream id related information
needs to be updated into DEPCMD while issuing START TRANSFER.
This patch does the same.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a new PID 0x7843 to the driver.
Let the new products be able to set up 3 serial ports with the driver.
Note that this depends on e8603076f5 ("USB: serial: mos7840: clean up
register handling").
Signed-off-by: JackyChou <jackychou@asix.com.tw>
[ johan: mention dependency in case anyone wants to backport this ]
Signed-off-by: Johan Hovold <johan@kernel.org>
In the read/write function, set port 2 independently in the 2-port case.
When setting the offset of port registers, the offset between port 1 and
other ports is different, so port 1 is set independently.
Then in the rest of ports, the port 2 between 2-ports case and 4-ports case
is different, so port 2 in 2-ports case is set independently.
Specifically, port 2 in the 2-port case maps to the registers used by
port 3 in the 4-port case.
Signed-off-by: JackyChou <jackychou@asix.com.tw>
[ johan: simplify register-offset handling at port probe, add a comment
and amend commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
The ACPI device with INT3515 _HID is representing a complex USB PD
hardware infrastructure which includes several I2C slave ICs.
We add an ID to the I2C multi instantiate list to enumerate
all I2C slaves correctly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In this second set of fixes for the current -rc cycle, we have some
regressions fixes for the old omap_udc driver done by Aaro Koskinen.
We're also reverting an old patch on dwc3 which is, now, known to
break USB certification in some cases.
We have a fix on u_ether for an unsafe list iteration.
-----BEGIN PGP SIGNATURE-----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=MIKU
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.20-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
USB: fixes for v4.20-rc4
In this second set of fixes for the current -rc cycle, we have some
regressions fixes for the old omap_udc driver done by Aaro Koskinen.
We're also reverting an old patch on dwc3 which is, now, known to
break USB certification in some cases.
We have a fix on u_ether for an unsafe list iteration.
* tag 'fixes-for-v4.20-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
usb: gadget: u_ether: fix unsafe list iteration
USB: omap_udc: fix rejection of out transfers when DMA is used
USB: omap_udc: fix USB gadget functionality on Palm Tungsten E
USB: omap_udc: fix omap_udc_start() on 15xx machines
USB: omap_udc: fix crashes on probe error and module removal
USB: omap_udc: use devm_request_irq()
Revert "usb: dwc3: gadget: skip Set/Clear Halt when invalid"
iscsi_target_mod is the only LIO fabric where fabric_ops.name differs from
the fabric_ops.fabric_name string. fabric_ops.name is used when matching
target/$fabric ConfigFS create paths, so rename it .fabric_alias and
fallback to target/$fabric vs .fabric_name comparison if .fabric_alias
isn't initialised. iscsi_target_mod is the only fabric module to set
.fabric_alias . All other fabric modules rely on .fabric_name matching and
can drop the duplicate string.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
All fabrics return a const string. In all cases *except* iSCSI the
get_fabric_name() string matches fabric_ops.name.
Both fabric_ops.get_fabric_name() and fabric_ops.name are user-facing, with
the former being used for PR/ALUA state and the latter for ConfigFS
(config/target/$name), so we unfortunately need to keep both strings around
for now. Replace the useless .get_fabric_name() accessor function with a
const string fabric_name member variable.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
list_for_each_entry_safe() is not safe for deleting entries from the
list if the spin lock, which protects it, is released and reacquired during
the list iteration. Fix this issue by replacing this construction with
a simple check if list is empty and removing the first entry in each
iteration. This is almost equivalent to a revert of the commit mentioned in
the Fixes: tag.
This patch fixes following issue:
--->8---
Unable to handle kernel NULL pointer dereference at virtual address 00000104
pgd = (ptrval)
[00000104] *pgd=00000000
Internal error: Oops: 817 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 1 PID: 84 Comm: kworker/1:1 Not tainted 4.20.0-rc2-next-20181114-00009-g8266b35ec404 #1061
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
Workqueue: events eth_work
PC is at rx_fill+0x60/0xac
LR is at _raw_spin_lock_irqsave+0x50/0x5c
pc : [<c065fee0>] lr : [<c0a056b8>] psr: 80000093
sp : ee7fbee8 ip : 00000100 fp : 00000000
r10: 006000c0 r9 : c10b0ab0 r8 : ee7eb5c0
r7 : ee7eb614 r6 : ee7eb5ec r5 : 000000dc r4 : ee12ac00
r3 : ee12ac24 r2 : 00000200 r1 : 60000013 r0 : ee7eb5ec
Flags: Nzcv IRQs off FIQs on Mode SVC_32 ISA ARM Segment none
Control: 10c5387d Table: 6d5dc04a DAC: 00000051
Process kworker/1:1 (pid: 84, stack limit = 0x(ptrval))
Stack: (0xee7fbee8 to 0xee7fc000)
...
[<c065fee0>] (rx_fill) from [<c0143b7c>] (process_one_work+0x200/0x738)
[<c0143b7c>] (process_one_work) from [<c0144118>] (worker_thread+0x2c/0x4c8)
[<c0144118>] (worker_thread) from [<c014a8a4>] (kthread+0x128/0x164)
[<c014a8a4>] (kthread) from [<c01010b4>] (ret_from_fork+0x14/0x20)
Exception stack(0xee7fbfb0 to 0xee7fbff8)
...
---[ end trace 64480bc835eba7d6 ]---
Fixes: fea14e68ff ("usb: gadget: u_ether: use better list accessors")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Gadget driver may take an unbounded amount of time to queue requests
after XferNotReady. This is important for isochronous endpoints which
need to be started for a specific (micro-)frame.
If we fail to start a transfer for isochronous endpoint, let's try
queueing to a future interval and see if that helps. We will stop trying
if we fail a start transfer for 5 intervals in the future.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Commit 387f869d25 ("usb: gadget: u_ether: conditionally align
transfer size") started aligning transfer size only if requested,
breaking omap_udc DMA mode. Set quirk_ep_out_aligned_size to restore
the old behaviour.
Fixes: 387f869d25 ("usb: gadget: u_ether: conditionally align transfer size")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
On Palm TE nothing happens when you try to use gadget drivers and plug
the USB cable. Fix by adding the board to the vbus sense quirk list.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
On OMAP 15xx machines there are no transceivers, and omap_udc_start()
always fails as it forgot to adjust the default return value.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We currently crash if usb_add_gadget_udc_release() fails, since the
udc->done is not initialized until in the remove function.
Furthermore, on module removal the udc data is accessed although
the release function is already triggered by usb_del_gadget_udc()
early in the function.
Fix by rewriting the release and remove functions, basically moving
all the cleanup into the release function, and doing the completion
only in the module removal case.
The patch fixes omap_udc module probe with a failing gadged, and also
allows the removal of omap_udc. Tested by running "modprobe omap_udc;
modprobe -r omap_udc" in a loop.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The current code fails to release the third irq on the error path
(observed by reading the code), and we get also multiple WARNs with
failing gadget drivers due to duplicate IRQ releases. Fix by using
devm_request_irq().
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Running out of requests on isochronous endpoints is part of normal
operation. We don't really need to know about it every time it
happens.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
They are much more useful in hexadecimal than in decimal. Moreover,
generic commands are already logged in hex.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Sometimes, errors happen when kicking transfers from
__dwc3_gadget_start_isoc(). In those cases, we need to pass along the
error so gadget driver can make informed decisions.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cherry G230 Stream 2.0 (G85-231) and 3.0 (G85-232) need this quirk to
function correctly. This fixes a but where double pressing numlock locks
up the device completely with need to replug the keyboard.
Signed-off-by: Michael Niewöhner <linux@mniewoehner.de>
Tested-by: Michael Niewöhner <linux@mniewoehner.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two new Realtek card readers require ums-realtek to work
correctly.
Add the new IDs to support them.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we have a list of cancelled requests, we can skip over TRBs
when END_TRANSFER command completes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Whenever we have a request in flight, we can move it to the cancelled
list and later simply iterate over that list and skip over any TRBs we
find.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Extract the logic for skipping over TRBs to its own function. This
makes the code slightly more readable and makes it easier to move this
call to its final resting place as a following patch.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that we track how many TRBs a request uses, it's easier to skip
over them in case of a call to usb_ep_dequeue(). Let's do so and
simplify the code a bit.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Both flags are used for the same purpose in dwc3: appending an extra
TRB at the end to deal with controller requirements. By combining both
flags into one, we make it clear that the situation is the same and
that they should be treated equally.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In DWC_usb31 version 1.70a-ea06 and prior, for highspeed and fullspeed
isochronous IN, BIT[15:14] of the 16-bit microframe number reported by
the XferNotReady event are invalid. The driver uses this number to
schedule the isochronous transfer and passes it to the START TRANSFER
command. Because this number is invalid, the command may fail. If
BIT[15:14] matches the internal 16-bit microframe, the START TRANSFER
command will pass and the transfer will start at the scheduled time, if
it is off by 1, the command will still pass, but the transfer will start
2 seconds in the future. For all other conditions, the START TRANSFER
command will fail with bus-expiry.
In order to workaround this issue, we can test for the correct
combination of BIT[15:14] by sending START TRANSFER commands with
different values of BIT[15:14]: 'b00, 'b01, 'b10, and 'b11. Each
combination is 2^14 uframe apart (or 2 seconds). 4 seconds into the
future will result in a bus-expiry status. As the result, within the 4
possible combinations for BIT[15:14], there will be 2 successful and 2
failure START COMMAND status. One of the 2 successful command status
will result in a 2-second delay start. The smaller BIT[15:14] value is
the correct combination.
Since there are only 4 outcomes and the results are ordered, we can
simply test 2 START TRANSFER commands with BIT[15:14] combinations 'b00
and 'b01 to deduce the smaller successful combination.
Let test0 = test status for combination 'b00 and test1 = test status for
'b01 of BIT[15:14]. The correct combination is as follow:
if test0 fails and test1 passes, BIT[15:14] is 'b01
if test0 fails and test1 fails, BIT[15:14] is 'b10
if test0 passes and test1 fails, BIT[15:14] is 'b11
if test0 passes and test1 passes, BIT[15:14] is 'b00
Synopsys STAR 9001202023: Wrong microframe number for isochronous IN
endpoints.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a new field to dwc3 structure to track VERSIONTYPE. The VERSIONTYPE
is represented in ASCII in the 32-bit VERSIONTYPE register. In
DWC_usb31, sub releases for each version are tracked with VERSIONTYPE
such as "ea01" and "ea02".
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some protocols implemented in userspace with FunctionFS might require large
buffers, e.g. 64kB or more. Currently the said memory is allocated with
kmalloc, which might fail should system memory be highly fragmented.
On the other hand, some UDC hardware allows scatter-gather operation and
this patch takes advantage of this capability: if the requested buffer
is larger than PAGE_SIZE and the UDC allows scatter-gather operation, then
the buffer is allocated with vmalloc and a scatterlist describing it is
created and passed to usb request.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Nothing to remap, only check length.
Define a minimal structure for CCID descriptor only used to check length.
As this descriptor shares the same value as HID descriptors, keep track and
compare current interface's class to expected HID and CCID standard values.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Trivial fix to spelling mistake in comment
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The vb2_ops structure can be const as it is only stored in the ops
field of a vb2_queue structure and this field is const.
Done with the help of Coccinelle.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Set GLPMCFG_LPM_ACCEPT_CTRL_ISOC bit in GLPMCFG register
to accept LPM token during ISOC transfers when TxFIFO is
not empty.
- Added two definitions.
#define GLPMCFG_LPM_ACCEPT_CTRL_CONTROL BIT(21)
#define GLPMCFG_LPM_ACCEPT_CTRL_ISOC BIT(22)
This patch uses GLPMCFG_LPM_ACCEPT_CTRL_ISOC.
GLPMCFG_LPM_ACCEPT_CTRL_CONTROL is defined for further use.
- Added setting GLPMCFG_LPM_ACCEPT_CTRL_ISOC bit in GLPMCFG
register in dwc2_gadget_init_lpm function.
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
According to the databook DCTL_RMTWKUPSIG bit
is defined in DCTL register not in DCFG.
Updated setting DCTL_RMTWKUPSIG bit to DCTL
register.
Fixes: 187c5298a1 ("usb: dwc2: gadget: Add handler for WkupAlert interrupt")
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
DWC_usb31 and DWC_usb3 v3.30a and higher do not support OTG mode. If
the controller supports DRD but the dr_mode is not specified or set to
OTG, then set the mode to peripheral.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds a safety connection way for "forced_b_device" with
"workaround_for_vbus" like below:
< Example for R-Car E3 Ebisu >
# modprobe <any usb gadget driver>
# echo 1 > /sys/kernel/debug/ee020000.usb/b_device
(connect a usb cable to host side.)
# echo 2 > /sys/kernel/debug/ee020000.usb/b_device
Previous code should have connected a usb cable before the "b_device"
is set to 1 on the Ebisu board. However, if xHCI driver on the board
is probed, it causes some troubles:
- Conflicts USB VBUS/signals between the board and another host.
- "Cannot enable. Maybe the USB cable is bad?" might happen on
both the board and another host with a usb hub.
- Cannot enumerate a usb gadget correctly because an interruption
of VBUS change happens unexpectedly.
Reported-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Allow extcon device, found by name, to provide DR status for USB.
This is needed, for example, in case of Intel Merrifield platform,
where the Intel Basin Cove PMIC provides an extcon device to communicate
the detected role.
Note, that the "linux,extcon-name" property name is only for kernel
internal use by X86/ACPI platform code and as such is not documented
in the device tree bindings.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Switch to device property for 'extcon' handling.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It's not very useful to repeat a bunch of probe deferral errors. And
it's also not very useful to log "failed" without telling the error
code.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The usb_gadget_ops structure can be const as it is only stored in
the ops field of a usb_gadget structure and this field is const.
Done with the help of Coccinelle.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Support the option to disable USB2 LPM. Set xhci "usb2-lpm-disable"
property via "snps,usb2-lpm-disable" property.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
GUSB2PHYCFG.ENBLSLPM enables the controller to assert low power signals
to the PHY. Unless disabled via device property, explicitly set
GUSB2PHYCFG.ENBLSLPM as it may not be set by default.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Current implementation only prints/sets the link state for peripheral
mode only. Check and prevent printing bogus link state if the current
mode of operation is not peripheral.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Highspeed device and below has different state names than superspeed and
higher. Add proper checks and printouts of link states for highspeed and
below.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
To dump internal LSP and endpoint state debug registers, we must write
to GDBGLSPMUX register. This patch correctly dump LSP and endpoint
states from the debug registers.
If the controller is in device mode, all LSP and endpoint state
registers will be dumped via the debugfs attribute "lsp_dump". In host
mode, the user has to write the LSP number to "lsp_dump" to dump a
specific LSP selection.
Fixes: 80b776340c ("usb: dwc3: Dump LSP and BMU debug info")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
TxFIFO and RxFIFO from GDBGFIFOSPACE are fifo depths in MDWIDTH. Convert
them into bytes for easier read.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The Tx/RxFIFO types in the GDBGFIFOSPACE.FIFO_QUEUE_SELECT are not
queue. Properly rename them.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This reverts commit ffb80fc672.
Turns out that commit is wrong. Host controllers are allowed to use
Clear Feature HALT as means to sync data toggle between host and
periperal.
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There is a hunk of code that is indented too much by one level, fix
this by removing the extraneous tabs.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a missing indentation before the return statement. Add it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Improve baud-rate generation by using rounding-to-closest instead of
truncation in divisor calculation.
Results have been verified by logic analyzer on an FT232RT (232BM) chip.
The following table shows the wanted baud rate, the baud rate obtained
with the old method (truncation), with the new method (rounding) and the
baud rate generated by the windows 10 driver. The numbers in parentheses
is the error.
+- Wanted --+------ Old -------+------ New -------+------ Win -------+
| 9600 | 9600 (0.00%) | 9604 (0.05%) | 9605 (0.05%) |
| 19200 | 19200 (0.00%) | 19199 (0.01%) | 19198 (0.01%) |
| 38400 | 38395 (0.01%) | 38431 (0.08%) | 38394 (0.02%) |
| 57600 | 57725 (0.22%) | 57540 (0.10%) | 57673 (0.13%) |
| 115200 | 115307 (0.09%) | 115330 (0.11%) | 115320 (0.10%) |
| 921600 | 919963 (0.18%) | 920386 (0.13%) | 920810 (0.09%) |
| 961200 | 996512 (3.67%) | 956480 (0.49%) | 956937 (0.44%) |
+-----------+------------------+------------------+------------------+
The error due to noise in the measurements is in the order of a few
tenths of a %. As can be seen, the baud rate is significantly improved
for some rates (e.g. 961200), and corresponds to the output given by the
windows driver.
The theoretical baud rate has been calculated for all baud rates from 1
to 3M, and as expected, the error is centered around 0, with a triangle
shape instead of a sawtooth, so the maximum error is decreased to half.
Signed-off-by: Nikolaj Fogh <nikolajfogh@gmail.com>
[ johan: edit commit message slightly ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Here are a number of small USB fixes for 4.20-rc4.
There's the usual xhci and dwc2/3 fixes as well as a few minor other
issues resolved for problems that have been reported. Full details are
in the shortlog.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW/ZsOg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymPlACeO1ii05UG6Mb47AC0sZbgMk5diWwAnRK3A0Pe
fSupZy5v6u1HBEormFco
=5k0S
-----END PGP SIGNATURE-----
Merge tag 'usb-4.20-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of small USB fixes for 4.20-rc4.
There's the usual xhci and dwc2/3 fixes as well as a few minor other
issues resolved for problems that have been reported. Full details are
in the shortlog.
All have been in linux-next for a while with no reported issues"
* tag 'usb-4.20-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: cdc-acm: add entry for Hiro (Conexant) modem
usb: xhci: Prevent bus suspend if a port connect change or polling state is detected
usb: core: Fix hub port connection events lost
usb: dwc3: gadget: fix ISOC TRB type on unaligned transfers
Revert "usb: gadget: ffs: Fix BUG when userland exits with submitted AIO transfers"
usb: dwc2: pci: Fix an error code in probe
usb: dwc3: Fix NULL pointer exception in dwc3_pci_remove()
xhci: Add quirk to workaround the errata seen on Cavium Thunder-X2 Soc
usb: xhci: fix timeout for transition from RExit to U0
usb: xhci: fix uninitialized completion when USB3 port got wrong status
xhci: Add check for invalid byte size error when UAS devices are connected.
xhci: handle port status events for removed USB3 hcd
xhci: Fix leaking USB3 shared_hcd at xhci removal
USB: misc: appledisplay: add 20" Apple Cinema Display
USB: quirks: Add no-lpm quirk for Raydium touchscreens
usb: quirks: Add delay-init quirk for Corsair K70 LUX RGB
USB: Wait for extra delay time after USB_PORT_FEAT_RESET for quirky hub
usb: dwc3: gadget: Properly check last unaligned/zero chain TRB
usb: dwc3: core: Clean up ULPI device
The F81532/534 had a internal configuration space to save & control
IC state with address F81534_CUSTOM_ADDRESS_START (0x2f00). Layout
as following:
+00h: to indicate the section is valid
+01h~04h: UART Mode & port availability
+05h~08h: Output pin control on IC power on
+09h~12h: Output pin control on working <-- New added
Old driver will use +05~08h as default on working, but newer IC will
configed with shutdown mode(7) in 05h~08h and working mode with RS232(1)
in 09h~12h. It'll make mainstream driver not working.
This patch will make mainstream driver compatible older and newer IC.
If using a old IC, the +05h~08h will be 00h~06h, we'll direct apply it.
If using a new IC, the +05h~08h will be 07h or larger, we'll read +09h~12h
to apply newer configuration.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The cdc-acm kernel module currently does not support the Hiro (Conexant)
H05228 USB modem. The patch below adds the device specific information:
idVendor 0x0572
idProduct 0x1349
Signed-off-by: Maarten Jacobs <maarten256@outlook.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'cipher' algorithms (single block ciphers) are always synchronous, so
passing CRYPTO_ALG_ASYNC in the mask to crypto_alloc_cipher() has no
effect. Many users therefore already don't pass it, but some still do.
This inconsistency can cause confusion, especially since the way the
'mask' argument works is somewhat counterintuitive.
Thus, just remove the unneeded CRYPTO_ALG_ASYNC flags.
This patch shouldn't change any actual behavior.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
USB3 roothub might autosuspend before a plugged USB3 device is detected,
causing USB3 device enumeration failure.
USB3 devices don't show up as connected and enabled until USB3 link trainig
completes. On a fast booting platform with a slow USB3 link training the
link might reach the connected enabled state just as the bus is suspending.
If this device is discovered first time by the xhci_bus_suspend() routine
it will be put to U3 suspended state like the other ports which failed to
suspend earlier.
The hub thread will notice the connect change and resume the bus,
moving the port back to U0
This U0 -> U3 -> U0 transition right after being connected seems to be
too much for some devices, causing them to first go to SS.Inactive state,
and finally end up stuck in a polling state with reset asserted
Fix this by failing the bus suspend if a port has a connect change or is
in a polling state in xhci_bus_suspend().
Don't do any port changes until all ports are checked, buffer all port
changes and only write them in the end if suspend can proceed
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This will clear the USB_PORT_FEAT_C_CONNECTION bit in case of a hub port reset
only if a device is was attached to the hub port before resetting the hub port.
Using a Lenovo T480s attached to the ultra dock it was not possible to detect
some usb-c devices at the dock usb-c ports because the hub_port_reset code
will clear the USB_PORT_FEAT_C_CONNECTION bit after the actual hub port reset.
Using this device combo the USB_PORT_FEAT_C_CONNECTION bit was set between the
actual hub port reset and the clear of the USB_PORT_FEAT_C_CONNECTION bit.
This ends up with clearing the USB_PORT_FEAT_C_CONNECTION bit after the
new device was attached such that it was not detected.
This patch will not clear the USB_PORT_FEAT_C_CONNECTION bit if there is
currently no device attached to the port before the hub port reset.
This will avoid clearing the connection bit for new attached devices.
Signed-off-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
type used on unaligned transfers on dwc3. Also a fix for a NULL pointer
dereference in dwc3_pci_remove(). Note that a recent commit on ffs was
reverted because it causes a regression elsewere.
-----BEGIN PGP SIGNATURE-----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=hWLY
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.20-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
For now only 5 small fixes. Most importantly, we have a fix for the TRB
type used on unaligned transfers on dwc3. Also a fix for a NULL pointer
dereference in dwc3_pci_remove(). Note that a recent commit on ffs was
reverted because it causes a regression elsewere.
* tag 'fixes-for-v4.20-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
usb: dwc3: gadget: fix ISOC TRB type on unaligned transfers
Revert "usb: gadget: ffs: Fix BUG when userland exits with submitted AIO transfers"
usb: dwc2: pci: Fix an error code in probe
usb: dwc3: Fix NULL pointer exception in dwc3_pci_remove()
usb: dwc3: gadget: Properly check last unaligned/zero chain TRB
usb: dwc3: core: Clean up ULPI device
When chaining ISOC TRBs together, only the first ISOC TRB should be of
type ISOC_FIRST, all others should be of type ISOC. This patch fixes
that.
Fixes: c6267a5163 ("usb: dwc3: gadget: align transfers to wMaxPacketSize")
Cc: <stable@vger.kernel.org> # v4.11+
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We added some error handling to this function but forgot to set the
error code on this path.
Fixes: ecd29dabb2 ("usb: dwc2: pci: Handle error cleanup in probe")
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In dwc3_pci_quirks() function, gpiod lookup table is only registered for
baytrail SOC. But in dwc3_pci_remove(), we try to unregistered it
without any checks. This leads to NULL pointer de-reference exception in
gpiod_remove_lookup_table() when unloading the module for non baytrail
SOCs. This patch fixes this issue.
Fixes: 5741022cbd ("usb: dwc3: pci: Add GPIO lookup table on platforms
without ACPI GPIO resources")
Cc: <stable@vger.kernel.org>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/usb/serial/mos7840.c: In function 'mos7840_interrupt_callback':
drivers/usb/serial/mos7840.c:604:14: warning:
variable 'st' set but not used [-Wunused-but-set-variable]
drivers/usb/serial/mos7840.c: In function 'mos7840_write':
drivers/usb/serial/mos7840.c:1303:17: warning:
variable 'data1' set but not used [-Wunused-but-set-variable]
drivers/usb/serial/mos7840.c:1700:11: warning:
variable 'iflag' set but not used [-Wunused-but-set-variable]
They are never used since introduction in commit 3f5429746d ("USB:
Moschip 7840 USB-Serial Driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/usb/serial/quatech2.c: In function 'qt2_process_read_urb':
drivers/usb/serial/quatech2.c:503:27: warning:
variable 'port_priv' set but not used [-Wunused-but-set-variable]
It not used any more after commit 2be818a116 ('Revert "USB: quatech2:
only write to the tty if the port is open."')
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Latest NVIDIA GPU cards have a Cypress CCGx Type-C controller
over I2C interface.
This UCSI I2C driver uses I2C bus driver interface for communicating
with Type-C controller.
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Implement workaround for ThunderX2 Errata-129 (documented in
CN99XX Known Issues" available at Cavium support site).
As per ThunderX2errata-129, USB 2 device may come up as USB 1
if a connection to a USB 1 device is followed by another connection to
a USB 2 device, the link will come up as USB 1 for the USB 2 device.
Resolution: Reset the PHY after the USB 1 device is disconnected.
The PHY reset sequence is done using private registers in XHCI register
space. After the PHY is reset we check for the PLL lock status and retry
the operation if it fails. From our tests, retrying 4 times is sufficient.
Add a new quirk flag XHCI_RESET_PLL_ON_DISCONNECT to invoke the workaround
in handle_xhci_port_status().
Cc: stable@vger.kernel.org
Signed-off-by: George Cherian <george.cherian@cavium.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This definition is used by msecs_to_jiffies in milliseconds.
According to the comments, max rexit timeout should be 20ms.
Align with the comments to properly calculate the delay.
Verified on Sunrise Point-LP and Cannon Lake.
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Realtek USB3.0 Card Reader [0bda:0328] reports wrong port status on
Cannon lake PCH USB3.1 xHCI [8086:a36d] after resume from S3,
after clear port reset it works fine.
Since this device is registered on USB3 roothub at boot,
when port status reports not superspeed, xhci_get_port_status will call
an uninitialized completion in bus_state[0].
Kernel will hang because of NULL pointer.
Restrict the USB2 resume status check in USB2 roothub to fix hang issue.
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Observed "TRB completion code (27)" error which corresponds to Stopped -
Length Invalid error(xhci spec section 4.17.4) while connecting USB to
SATA bridge.
Looks like this case was not considered when the following patch[1] was
committed. Hence adding this new check which can prevent
the invalid byte size error.
[1] ade2e3a xhci: handle transfer events without TRB pointer
Cc: <stable@vger.kernel.org>
Signed-off-by: Sandeep Singh <sandeep.singh@amd.com>
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
cc: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At xhci removal the USB3 hcd (shared_hcd) is removed before the primary
USB2 hcd. Interrupts for port status changes may still occur for USB3
ports after the shared_hcd is freed, causing NULL pointer dereference.
Check if xhci->shared_hcd is still valid before handing USB3 port events
Cc: <stable@vger.kernel.org>
Reported-by: Peter Chen <peter.chen@nxp.com>
Tested-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ensure that the shared_hcd pointer is valid when calling usb_put_hcd()
The shared_hcd is removed and freed in xhci by first calling
usb_remove_hcd(xhci->shared_hcd), and later
usb_put_hcd(xhci->shared_hcd)
Afer commit fe190ed0d6 ("xhci: Do not halt the host until both HCD have
disconnected their devices.") the shared_hcd was never properly put as
xhci->shared_hcd was set to NULL before usb_put_hcd(xhci->shared_hcd) was
called.
shared_hcd (USB3) is removed before primary hcd (USB2).
While removing the primary hcd we might need to handle xhci interrupts
to cleanly remove last USB2 devices, therefore we need to set
xhci->shared_hcd to NULL before removing the primary hcd to let xhci
interrupt handler know shared_hcd is no longer available.
xhci-plat.c, xhci-histb.c and xhci-mtk first create both their hcd's before
adding them. so to keep the correct reverse removal order use a temporary
shared_hcd variable for them.
For more details see commit 4ac53087d6 ("usb: xhci: plat: Create both
HCDs before adding them")
Fixes: fe190ed0d6 ("xhci: Do not halt the host until both HCD have disconnected their devices.")
Cc: Joel Stanley <joel@jms.id.au>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Jianguo Sun <sunjianguo1@huawei.com>
Cc: <stable@vger.kernel.org>
Reported-by: Jack Pham <jackp@codeaurora.org>
Tested-by: Jack Pham <jackp@codeaurora.org>
Tested-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add another Apple Cinema Display to the list of supported displays
Signed-off-by: Mattias Jacobsson <2pi@mok.nu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Raydium USB touchscreen fails to set config if LPM is enabled:
[ 2.030658] usb 1-8: New USB device found, idVendor=2386, idProduct=3119
[ 2.030659] usb 1-8: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.030660] usb 1-8: Product: Raydium Touch System
[ 2.030661] usb 1-8: Manufacturer: Raydium Corporation
[ 7.132209] usb 1-8: can't set config #1, error -110
Same behavior can be observed on 2386:3114.
Raydium claims the touchscreen supports LPM under Windows, so I used
Microsoft USB Test Tools (MUTT) [1] to check its LPM status. MUTT shows
that the LPM doesn't work under Windows, either. So let's just disable LPM
for Raydium touchscreens.
[1] https://docs.microsoft.com/en-us/windows-hardware/drivers/usbcon/usb-test-tools
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Following on from this patch: https://lkml.org/lkml/2017/11/3/516,
Corsair K70 LUX RGB keyboards also require the DELAY_INIT quirk to
start correctly at boot.
Dmesg output:
usb 1-6: string descriptor 0 read error: -110
usb 1-6: New USB device found, idVendor=1b1c, idProduct=1b33
usb 1-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-6: can't set config #1, error -110
Signed-off-by: Emmanuel Pescosta <emmanuelpescosta099@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Devices connected under Terminus Technology Inc. Hub (1a40:0101) may
fail to work after the system resumes from suspend:
[ 206.063325] usb 3-2.4: reset full-speed USB device number 4 using xhci_hcd
[ 206.143691] usb 3-2.4: device descriptor read/64, error -32
[ 206.351671] usb 3-2.4: device descriptor read/64, error -32
Info for this hub:
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=480 MxCh= 4
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1a40 ProdID=0101 Rev=01.11
S: Product=USB 2.0 Hub
C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
Some expirements indicate that the USB devices connected to the hub are
innocent, it's the hub itself is to blame. The hub needs extra delay
time after it resets its port.
Hence wait for extra delay, if the device is connected to this quirky
hub.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trivial fix to spelling mistake in comment
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dma_pool_destroy() can handle NULL pointer correctly, so there is
no need to check NULL pointer before calling dma_pool_destroy().
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During the initial connect to a non-pd port, sink would hard reset
twice before deeming that the port partner is non-pd. TCPM sets the
the charge path to false during the hard reset. This causes unnecessary
connects/disconnects of charge path and makes port take longer to
charge from the non-pd ports. Avoid this by not setting the charge path
to false unless the partner has already identified to be pd capable.
When partner is a pd port, set the charge path to false in
SNK_HARD_RESET_SINK_OFF. Set the current limits to default value based
of CC pull up and resume the charge path when port enters
SNK_HARD_RESET_SINK_ON.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
--------
Changes in V3:
Rebase on top of usb-next
Changes in V2:
Based on feedback of jackp@codeaurora.org
- vsafe_5v_hard_reset flag from tcpc_config is removed
- Patch only differentiates between pd port partner and non-pd port
partner
V1 version of the patch is here:
https://lkml.org/lkml/2018/9/14/11
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During HARD_RESET the data link is disconnected.
For self powered device, the spec is advising against doing that.
>From USB_PD_R3_0
7.1.5 Response to Hard Resets
Device operation during and after a Hard Reset is defined as follows:
Self-powered devices Should Not disconnect from USB during a Hard Reset
(see Section 9.1.2).
Bus powered devices will disconnect from USB during a Hard Reset due to the
loss of their power source.
Tackle this by letting TCPM know whether the device is self or bus powered.
This overcomes unnecessary port disconnections from hard reset.
Also, speeds up the enumeration time when connected to Type-A ports.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
---------
Version history:
V3:
Rebase on top of usb-next
V2:
Based on feedback from heikki.krogerus@linux.intel.com
- self_powered added to the struct tcpm_port which is populated from
a. "connector" node of the device tree in tcpm_fw_get_caps()
b. "self_powered" node of the tcpc_config in tcpm_copy_caps
Based on feedbase from linux@roeck-us.net
- Code was refactored
- SRC_HARD_RESET_VBUS_OFF sets the link state to false based
on self_powered flag
V1 located here:
https://lkml.org/lkml/2018/9/13/94
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current check for the last extra TRB for zero and unaligned transfers
does not account for isoc OUT. The last TRB of the Buffer Descriptor for
isoc OUT transfers will be retired with HWO=0. As a result, we won't
return early. The req->remaining will be updated to include the BUFSIZ
count of the extra TRB, and the actual number of transferred bytes
calculation will be wrong.
To fix this, check whether it's a short or zero packet and the last TRB
chain bit to return early.
Fixes: c6267a5163 ("usb: dwc3: gadget: align transfers to wMaxPacketSize")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If dwc3_core_init_mode() fails with deferred probe,
next probe fails on sysfs with
sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:11.0/dwc3.0.auto/dwc3.0.auto.ulpi'
To avoid this failure, clean up ULPI device.
Cc: <stable@vger.kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Pull AFS updates from Al Viro:
"AFS series, with some iov_iter bits included"
* 'work.afs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (26 commits)
missing bits of "iov_iter: Separate type from direction and use accessor functions"
afs: Probe multiple fileservers simultaneously
afs: Fix callback handling
afs: Eliminate the address pointer from the address list cursor
afs: Allow dumping of server cursor on operation failure
afs: Implement YFS support in the fs client
afs: Expand data structure fields to support YFS
afs: Get the target vnode in afs_rmdir() and get a callback on it
afs: Calc callback expiry in op reply delivery
afs: Fix FS.FetchStatus delivery from updating wrong vnode
afs: Implement the YFS cache manager service
afs: Remove callback details from afs_callback_break struct
afs: Commit the status on a new file/dir/symlink
afs: Increase to 64-bit volume ID and 96-bit vnode ID for YFS
afs: Don't invoke the server to read data beyond EOF
afs: Add a couple of tracepoints to log I/O errors
afs: Handle EIO from delivery function
afs: Fix TTL on VL server and address lists
afs: Implement VL server rotation
afs: Improve FS server rotation error handling
...
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJb2F9AAAoJEAhfPr2O5OEVm5YP/Ak53aAEI1oJNequwdTYKc+/
2xWRpYWREa1g+x4MlqWO+szlPWbGXCUVwye8ii2N/xihLapsKVrLCr/dDd5khsvw
bDux33BzpU3Ug/ncQKD6ZZv4vVRzG8DMPcpkOwSs0OoboJns6AkHVGCugR32qZsH
3SH/r1aJce0oK1rrzgbYYZHTvaPshvY2IOLPKrtFmO+73iCVRhpSdWjFsY+q2Alp
+3Ho/06iQYB2i+enXrwoIKHAYoXArXYbxS2dhaNz+NURrOAytmgfMisvvt67heHx
IEilE0AcSjjlN/eyOxp+WCZrg9JLXVzZLX6ZnqqM2OEu1AS/XBultJBsGaN0hOiV
dir2enoHNNOStI40hNSdbumg9I0Txmag2jtpaGyaBnnGmGRJ/JIYegCPRVMLygAf
HHFHjR4fnRnqZrlh9OGAHaqc9RNlUgFVdlyqFtdyIah+aNeuij3o69mWM35QMLhw
/0dTXBUXw9aD1dEg1cZ6PdzLWJgDd7n1gIdfzzzzLnzmBwmmhqxW8+evu9qSAXsP
rnEZuE77HYKVfiacWMwpZK6+lT51STAE8ouo3N8fmaC+4RQmpq0dYXtR8RnlcSUD
hKpJ6UsIIb5A6xKX7ed8x6FxV14TEEaa042A4eclxsAFiqqkNfWSozqV0vfW5vCD
2lrsuN3knpfh7XDBSr0y
=V4X4
-----END PGP SIGNATURE-----
Merge tag 'media/v4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull new experimental media request API from Mauro Carvalho Chehab:
"A new media request API
This API is needed to support device drivers that can dynamically
change their parameters for each new frame. The latest versions of
Google camera and codec HAL depends on such feature.
At this stage, it supports only stateless codecs.
It has been discussed for a long time (at least over the last 3-4
years), and we finally reached to something that seem to work.
This series contain both the API and core changes required to support
it and a new m2m decoder driver (cedrus).
As the current API is still experimental, the only real driver using
it (cedrus) was added at staging[1]. We intend to keep it there for a
while, in order to test the API. Only when we're sure that this API
works for other cases (like encoders), we'll move this driver out of
staging and set the API into a stone.
[1] We added support for the vivid virtual driver (used only for
testing) to it too, as it makes easier to test the API for the ones
that don't have the cedrus hardware"
* tag 'media/v4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (53 commits)
media: dt-bindings: Document the Rockchip VPU bindings
media: platform: Add Cedrus VPU decoder driver
media: dt-bindings: media: Document bindings for the Cedrus VPU driver
media: v4l: Add definition for the Sunxi tiled NV12 format
media: v4l: Add definitions for MPEG-2 slice format and metadata
media: videobuf2-core: Rework and rename helper for request buffer count
media: v4l2-ctrls.c: initialize an error return code with zero
media: v4l2-compat-ioctl32.c: add missing documentation for a field
media: media-request: update documentation
media: media-request: EPERM -> EACCES/EBUSY
media: v4l2-ctrls: improve media_request_(un)lock_for_update
media: v4l2-ctrls: use media_request_(un)lock_for_access
media: media-request: add media_request_(un)lock_for_access
media: vb2: set reqbufs/create_bufs capabilities
media: videodev2.h: add new capabilities for buffer types
media: buffer.rst: only set V4L2_BUF_FLAG_REQUEST_FD for QBUF
media: v4l2-ctrls: return -EACCES if request wasn't completed
media: media-request: return -EINVAL for invalid request_fds
media: vivid: add request support
media: vivid: add mc
...
Move remaining definitions and declarations from include/linux/bootmem.h
into include/linux/memblock.h and remove the redundant header.
The includes were replaced with the semantic patch below and then
semi-automated removal of duplicated '#include <linux/memblock.h>
@@
@@
- #include <linux/bootmem.h>
+ #include <linux/memblock.h>
[sfr@canb.auug.org.au: dma-direct: fix up for the removal of linux/bootmem.h]
Link: http://lkml.kernel.org/r/20181002185342.133d1680@canb.auug.org.au
[sfr@canb.auug.org.au: powerpc: fix up for removal of linux/bootmem.h]
Link: http://lkml.kernel.org/r/20181005161406.73ef8727@canb.auug.org.au
[sfr@canb.auug.org.au: x86/kaslr, ACPI/NUMA: fix for linux/bootmem.h removal]
Link: http://lkml.kernel.org/r/20181008190341.5e396491@canb.auug.org.au
Link: http://lkml.kernel.org/r/1536927045-23536-30-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The alloc_bootmem_pages_nopanic(size) is a shortcut for
__alloc_bootmem_nopanic(size, PAGE_SIZE, BOOTMEM_LOW_LIMIT) which allocates
PAGE_SIZE aligned memory. Since BOOTMEM_LOW_LIMIT is hardwired to 0 there
is no restrictions on where the allocated memory should reside.
The memblock_alloc_nopanic(size, PAGE_SIZE) also allocates PAGE_SIZE
aligned memory without any restrictions and thus can be used as a
replacement for alloc_bootmem_pages_nopanic()
Link: http://lkml.kernel.org/r/1536927045-23536-12-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here is the big USB/PHY driver patches for 4.20-rc1
Lots of USB changes in here, primarily in these areas:
- typec updates and new drivers
- new PHY drivers
- dwc2 driver updates and additions (this old core keeps getting added
to new devices.)
- usbtmc major update based on the industry group coming together and
working to add new features and performance to the driver.
- USB gadget additions for new features
- USB gadget configfs updates
- chipidea driver updates
- other USB gadget updates
- USB serial driver updates
- renesas driver updates
- xhci driver updates
- other tiny USB driver updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW9LlHw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymnvwCffYmMWyMG9zSOw1oSzFPl7TVN1hYAoMyJqzLg
umyLwWxC9ZWWkrpc3iD8
=ux+Y
-----END PGP SIGNATURE-----
Merge tag 'usb-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big USB/PHY driver patches for 4.20-rc1
Lots of USB changes in here, primarily in these areas:
- typec updates and new drivers
- new PHY drivers
- dwc2 driver updates and additions (this old core keeps getting
added to new devices.)
- usbtmc major update based on the industry group coming together and
working to add new features and performance to the driver.
- USB gadget additions for new features
- USB gadget configfs updates
- chipidea driver updates
- other USB gadget updates
- USB serial driver updates
- renesas driver updates
- xhci driver updates
- other tiny USB driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (229 commits)
usb: phy: ab8500: silence some uninitialized variable warnings
usb: xhci: tegra: Add genpd support
usb: xhci: tegra: Power-off power-domains on removal
usbip:vudc: BUG kmalloc-2048 (Not tainted): Poison overwritten
usbip: tools: fix atoi() on non-null terminated string
USB: misc: appledisplay: fix backlight update_status return code
phy: phy-pxa-usb: add a new driver
usb: host: add DT bindings for faraday fotg2
usb: host: ohci-at91: fix request of irq for optional gpio
usb/early: remove set but not used variable 'remain_length'
usb: typec: Fix copy/paste on typec_set_vconn_role() kerneldoc
usb: typec: tcpm: Report back negotiated PPS voltage and current
USB: core: remove set but not used variable 'udev'
usb: core: fix memory leak on port_dev_path allocation
USB: net2280: Remove ->disconnect() callback from net2280_pullup()
usb: dwc2: disable power_down on rockchip devices
usb: gadget: udc: renesas_usb3: add support for r8a77990
dt-bindings: usb: renesas_usb3: add bindings for r8a77990
usb: gadget: udc: renesas_usb3: Add r8a774a1 support
USB: serial: cypress_m8: remove set but not used variable 'iflag'
...
Pull tty ioctl updates from Al Viro:
"This is the compat_ioctl work related to tty ioctls.
Quite a bit of dead code taken out, all tty-related stuff gone from
fs/compat_ioctl.c. A bunch of compat bugs fixed - some still remain,
but all more or less generic tty-related ioctls should be covered
(remaining issues are in things like driver-private ioctls in a pcmcia
serial card driver not getting properly handled in 32bit processes on
64bit host, etc)"
* 'work.tty-ioctl' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (53 commits)
kill TIOCSERGSTRUCT
change semantics of ldisc ->compat_ioctl()
kill TIOCSER[SG]WILD
synclink_gt(): fix compat_ioctl()
pty: fix compat ioctls
compat_ioctl - kill keyboard ioctl handling
gigaset: add ->compat_ioctl()
vt_compat_ioctl(): clean up, use compat_ptr() properly
gigaset: don't try to printk userland buffer contents
dgnc: don't bother with (empty) stub for TCXONC
dgnc: leave TIOC[GS]SOFTCAR to ldisc
remove fallback to drivers for TIOCGICOUNT
dgnc: break-related ioctls won't reach ->ioctl()
kill the rest of tty COMPAT_IOCTL() entries
dgnc: TIOCM... won't reach ->ioctl()
isdn_tty: TCSBRK{,P} won't reach ->ioctl()
kill capinc_tty_ioctl()
take compat TIOC[SG]SERIAL treatment into tty_compat_ioctl()
synclink: reduce pointless checks in ->ioctl()
complete ->[sg]et_serial() switchover
...
Pull siginfo updates from Eric Biederman:
"I have been slowly sorting out siginfo and this is the culmination of
that work.
The primary result is in several ways the signal infrastructure has
been made less error prone. The code has been updated so that manually
specifying SEND_SIG_FORCED is never necessary. The conversion to the
new siginfo sending functions is now complete, which makes it
difficult to send a signal without filling in the proper siginfo
fields.
At the tail end of the patchset comes the optimization of decreasing
the size of struct siginfo in the kernel from 128 bytes to about 48
bytes on 64bit. The fundamental observation that enables this is by
definition none of the known ways to use struct siginfo uses the extra
bytes.
This comes at the cost of a small user space observable difference.
For the rare case of siginfo being injected into the kernel only what
can be copied into kernel_siginfo is delivered to the destination, the
rest of the bytes are set to 0. For cases where the signal and the
si_code are known this is safe, because we know those bytes are not
used. For cases where the signal and si_code combination is unknown
the bits that won't fit into struct kernel_siginfo are tested to
verify they are zero, and the send fails if they are not.
I made an extensive search through userspace code and I could not find
anything that would break because of the above change. If it turns out
I did break something it will take just the revert of a single change
to restore kernel_siginfo to the same size as userspace siginfo.
Testing did reveal dependencies on preferring the signo passed to
sigqueueinfo over si->signo, so bit the bullet and added the
complexity necessary to handle that case.
Testing also revealed bad things can happen if a negative signal
number is passed into the system calls. Something no sane application
will do but something a malicious program or a fuzzer might do. So I
have fixed the code that performs the bounds checks to ensure negative
signal numbers are handled"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (80 commits)
signal: Guard against negative signal numbers in copy_siginfo_from_user32
signal: Guard against negative signal numbers in copy_siginfo_from_user
signal: In sigqueueinfo prefer sig not si_signo
signal: Use a smaller struct siginfo in the kernel
signal: Distinguish between kernel_siginfo and siginfo
signal: Introduce copy_siginfo_from_user and use it's return value
signal: Remove the need for __ARCH_SI_PREABLE_SIZE and SI_PAD_SIZE
signal: Fail sigqueueinfo if si_signo != sig
signal/sparc: Move EMT_TAGOVF into the generic siginfo.h
signal/unicore32: Use force_sig_fault where appropriate
signal/unicore32: Generate siginfo in ucs32_notify_die
signal/unicore32: Use send_sig_fault where appropriate
signal/arc: Use force_sig_fault where appropriate
signal/arc: Push siginfo generation into unhandled_exception
signal/ia64: Use force_sig_fault where appropriate
signal/ia64: Use the force_sig(SIGSEGV,...) in ia64_rt_sigreturn
signal/ia64: Use the generic force_sigsegv in setup_frame
signal/arm/kvm: Use send_sig_mceerr
signal/arm: Use send_sig_fault where appropriate
signal/arm: Use force_sig_fault where appropriate
...
In the iov_iter struct, separate the iterator type from the iterator
direction and use accessor functions to access them in most places.
Convert a bunch of places to use switch-statements to access them rather
then chains of bitwise-AND statements. This makes it easier to add further
iterator types. Also, this can be more efficient as to implement a switch
of small contiguous integers, the compiler can use ~50% fewer compare
instructions than it has to use bitwise-and instructions.
Further, cease passing the iterator type into the iterator setup function.
The iterator function can set that itself. Only the direction is required.
Signed-off-by: David Howells <dhowells@redhat.com>
Smatch complains that "reg" can be uninitialized if the
abx500_get_register_interruptible() call fails. It's an interruptable
function, so we should check if the user presses CTRL-C.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The generic power-domain framework has been updated to allow devices
that require more than one power-domain to create a new device for
each power-domain required and then link these new power-domain
devices to the consumer device.
Update the Tegra xHCI driver to use the new APIs provided by the
generic power-domain framework so we can use the generic power-domain
framework for managing the xHCI controllers power-domains. Please
note that to maintain backward compatibility with older device-tree
blobs these new generic power-domain APIs are only used if the
'power-domains' property is present and otherwise we fall back to
using the legacy Tegra APIs for managing the power-domains.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the XUSB power domains used by the Tegra xHCI controller are
never powered off on the removal of the driver, however, they will be
powered off on probe failure. Update the removal code to be consistent
with the probe failure path to power off the XUSB power domains.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In rmmod path, usbip_vudc does platform_device_put() twice once from
platform_device_unregister() and then from put_vudc_device().
The second put results in:
BUG kmalloc-2048 (Not tainted): Poison overwritten error or
BUG: KASAN: use-after-free in kobject_put+0x1e/0x230 if KASAN is
enabled.
[ 169.042156] calling init+0x0/0x1000 [usbip_vudc] @ 1697
[ 169.042396] =============================================================================
[ 169.043678] probe of usbip-vudc.0 returned 1 after 350 usecs
[ 169.044508] BUG kmalloc-2048 (Not tainted): Poison overwritten
[ 169.044509] -----------------------------------------------------------------------------
...
[ 169.057849] INFO: Freed in device_release+0x2b/0x80 age=4223 cpu=3 pid=1693
[ 169.057852] kobject_put+0x86/0x1b0
[ 169.057853] 0xffffffffc0c30a96
[ 169.057855] __x64_sys_delete_module+0x157/0x240
Fix it to call platform_device_del() instead and let put_vudc_device() do
the platform_device_put().
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Upon success the update_status handler returns a positive number
corresponding to the number of bytes transferred by usb_control_msg.
However the return code of the update_status handler should indicate if
an error occurred(negative) or how many bytes of the user's input to sysfs
that was consumed. Return code zero indicates all bytes were consumed.
The bug can for example result in the update_status handler being called
twice, the second time with only the "unconsumed" part of the user's input
to sysfs. Effectively setting an incorrect brightness.
Change the update_status handler to return zero for all successful
transactions and forward usb_control_msg's error code upon failure.
Signed-off-by: Mattias Jacobsson <2pi@mok.nu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the USB-serial updates for 4.20-rc1, including:
- support for CBUS GPIO on FTDI devices (FTX and FT232R)
- fix of a long-standing transfer-length bug
Included are also various clean ups.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=V6Jo
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.20-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.20-rc1
Here are the USB-serial updates for 4.20-rc1, including:
- support for CBUS GPIO on FTDI devices (FTX and FT232R)
- fix of a long-standing transfer-length bug
Included are also various clean ups.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-4.20-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: cypress_m8: remove set but not used variable 'iflag'
USB: serial: cypress_m8: fix interrupt-out transfer length
USB: serial: ftdi_sio: add support for FT232R CBUS gpios
USB: serial: ftdi_sio: fix gpio name collisions
USB: serial: ftdi_sio: implement GPIO support for FT-X devices
USB: serial: cypress_m8: fix spelling mistake "retreiving" -> "retrieving"
num can be indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/usb/gadget/function/f_mass_storage.c:3177 fsg_lun_make() warn:
potential spectre issue 'fsg_opts->common->luns' [r] (local cap)
Fix this by sanitizing num before using it to index
fsg_opts->common->luns
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Felipe Balbi <felipe.balbi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 7a68d9fb85 ("USB: usbdevfs: sanitize flags more") checks the
transfer flags for URBs submitted from userspace via usbfs. However,
the check for whether the USBDEVFS_URB_SHORT_NOT_OK flag should be
allowed for a control transfer was added in the wrong place, before
the code has properly determined the direction of the control
transfer. (Control transfers are special because for them, the
direction is set by the bRequestType byte of the Setup packet rather
than direction bit of the endpoint address.)
This patch moves code which sets up the allow_short flag for control
transfers down after is_in has been set to the correct value.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+24a30223a4b609bb802e@syzkaller.appspotmail.com
Fixes: 7a68d9fb85 ("USB: usbdevfs: sanitize flags more")
CC: Oliver Neukum <oneukum@suse.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
atmel,oc-gpio is optional. Request its irq only when atmel,oc is set
in device tree.
devm_gpiod_get_index_optional returns NULL if -ENOENT. Check its
return value for NULL before error, because it is more probable that
atmel,oc is not set.
This fixes the following errors on boards where atmel,oc is not set in
device tree:
[ 0.960000] at91_ohci 500000.ohci: failed to request gpio "overcurrent" IRQ
[ 0.960000] at91_ohci 500000.ohci: failed to request gpio "overcurrent" IRQ
[ 0.970000] at91_ohci 500000.ohci: failed to request gpio "overcurrent" IRQ
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
... and fix the return value - on success it used to have ioctl(2)
fill the user-supplied struct serial_struct and return -ENOTTY.
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
add such methods for usb_serial_driver, provide tty_operations
->[sg]et_serial() calling those. For now the lack of methods
in driver means ENOIOCTLCMD from usb-serial ->[sg]et_serial(),
making tty_ioctl() fall back to calling ->ioctl(). Once all
drivers are converted, we'll be returning -ENOTTY instead,
completing the switchover.
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Intel Apollo Lake has the same internal USB role mux as
Intel Cherry Trail.
Cc: <stable@vger.kernel.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing pm_runtime_disable() to remove(), in order to avoid
an Unbalanced pm_runtime_enable when the module is removed and
re-probed.
Error log:
root@intel-corei7-64:~# modprobe -r intel_xhci_usb_role_switch
root@intel-corei7-64:~# modprobe intel_xhci_usb_role_switch
intel_xhci_usb_sw intel_xhci_usb_sw: Unbalanced pm_runtime_enable!
Fixes: cb29684686 (usb: roles: intel_xhci: Enable runtime PM)
Cc: <stable@vger.kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb standard ("Universal Serial Bus Class Definitions for Communication
Devices") distiguishes between "consistent signals" (DSR, DCD), and
"irregular signals" (break, ring, parity error, framing error, overrun).
The bits of "irregular signals" are set, if this error/event occurred on
the device side and are immeadeatly unset, if the serial state notification
was sent.
Like other drivers of real serial ports do, just the occurence of those
events should be counted in serial_icounter_struct (but no 1->0
transitions).
Signed-off-by: Tobias Herzog <t-herzog@gmx.de>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Resetting the write index of the notification buffer on urb unlink (e.g.
closing a cdc-acm device from userspace) may lead to wrong interpretation
of further received notifications, in case the index is not 0 when urb
unlink happens (i.e. when parts of a notification already have been
transferred). On the device side there is no "reset" of the notification
transimission and thus we would get out of sync with the device.
Signed-off-by: Tobias Herzog <t-herzog@gmx.de>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a device splits up a control message and a reset() happens
between the parts, the message is lost and already recieved parts
must be dropped.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: 1aba579f3c ("cdc-acm: handle read pipe errors")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vhci_hub_control() accesses port_status array with out of bounds port
value. Fix it to reference port_status[] only with a valid rhport value
when invalid_rhport flag is true.
The invalid_rhport flag is set early on after detecting in port value
is within the bounds or not.
The following is used reproduce the problem and verify the fix:
C reproducer: https://syzkaller.appspot.com/x/repro.c?x=14ed8ab6400000
Reported-by: syzbot+bccc1fe10b70fadc78d0@syzkaller.appspotmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/usb/early/xhci-dbc.c: In function 'xdbc_handle_tx_event':
drivers/usb/early/xhci-dbc.c:720:9: warning:
variable 'remain_length' set but not used [-Wunused-but-set-variable]
It never be used since introduction in
commit aeb9dd1de9 ("usb/early: Add driver for xhci debug capability")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This must have been copy pasted from the function above. Fix it.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently when requesting a specific voltage or current through
the psy interface, for PPS, when reading back from that interface
the values will always be the same as previously given, if the
request was successful. However PPS only allows for 20mV voltage
steps and 50mA current steps, and the psy class expects microvolt
and micro amp requests, so inbetween values can be provided through
this interface. Really when reading back the true values negotiated
should be given, and not the ones originally asked for.
To report the actual values negotiated with the Source, the values
stored are now rounded down to the relevant step units prior to
building the PPS request, so that those values are later correctly
reported through the psy interface. In addition this improves the
adjustments made to meet the operating power requirements of the
platform, which previously could have been slightly out due to not
using valid PPS units of voltage and current.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/usb/core/driver.c: In function 'usb_driver_claim_interface':
drivers/usb/core/driver.c:513:21: warning:
variable 'udev' set but not used [-Wunused-but-set-variable]
Since commit c183813fce ("USB: remove LPM management from
usb_driver_claim_interface()"), 'udev' is not used.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the allocation of port_dev_path from the call to
kobject_get_path is not being kfree'd, causing a memory leak. Fix
this by kfree'ing this at the end of the function. Add an extra
error exit path to fix one of the early leaks when envp[0] fails
to be allocated.
Detected by CoverityScan, CID#1473771 ("Resource Leak")
Fixes: 201af55da8 ("usb: core: added uevent for over-current")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- improve overcorrent handling for imx
- some small code restructure (no function affect)
-----BEGIN PGP SIGNATURE-----
iQEwBAABCAAaBQJburdqExxwZXRlci5jaGVuQG54cC5jb20ACgkQSFkpgVDWcbsr
ogf8C3QeuruN4+awCx4VQ7QPOhy0ewdr0OL3DCt1wjZkhvKilXcLHtKimbm7QQ7F
9tHFpxya63MwZvnqjEGR/EgJpTPGVTx1KSBcBoEQn5qP+iYA/xVSYGpeLEHGZtQE
FtsJGXg/dT1uzho43CibCksqiyHpScNAdUn9wl6go/LJKycVQ3nu+6R+kXbc+0ca
gzPXUsApG4KTEJ8SH5eGZnx2uqZzhJnuYXDRr/8mw6S1GyM6wlobVHvSyhpj1uGy
OsXluLgfu/+o+HYKwmKpqg2gZonk+1r2rE0qSmoAI7rYmX3irBC6VvASYqrok5jj
lKQ/a/M8IeIsXo1a/Xv62SKU3w==
=loIF
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-testing
Peter writes:
- Add pinctrl support for dual-role switch at chipidea-core
- improve overcorrent handling for imx
- some small code restructure (no function affect)
* tag 'usb-ci-v4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
usb: chipidea: Fix otg event handler
usb: chipidea: Prevent unbalanced IRQ disable
doc: usb: ci-hdrc-usb2: Add pinctrl properties definition
usb: chipidea: Add dynamic pinctrl selection
usb: chipidea: imx: make MODULE_LICENCE and SPDX-identifier match
usb: chipidea: imx: enable OTG overcurrent in case USB subsystem is already started
usb: chipidea: imx: do not use preprocessor conditionals for PM
With 63 non-merge commits, this is not a large merge window for USB
peripheral. The largest changes go to the UVC gadget driver which a
few folks have been improving.
Apart from UVC changes, we have a few more devices being added to
Renesas USB3 and DWC3 controller drivers and a couple minor bug fixes
on other drivers.
-----BEGIN PGP SIGNATURE-----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=XZcP
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB for v4.20
With 63 non-merge commits, this is not a large merge window for USB
peripheral. The largest changes go to the UVC gadget driver which a
few folks have been improving.
Apart from UVC changes, we have a few more devices being added to
Renesas USB3 and DWC3 controller drivers and a couple minor bug fixes
on other drivers.
* tag 'usb-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (63 commits)
USB: net2280: Remove ->disconnect() callback from net2280_pullup()
usb: dwc2: disable power_down on rockchip devices
usb: gadget: udc: renesas_usb3: add support for r8a77990
dt-bindings: usb: renesas_usb3: add bindings for r8a77990
usb: gadget: udc: renesas_usb3: Add r8a774a1 support
usb: gadget: udc: renesas_usb3: Fix b-device mode for "workaround"
usb: dwc2: gadget: Add handler for WkupAlert interrupt
usb: dwc2: gadget: enable WKUP_ALERT interrupt
usb: dwc2: gadget: Program GREFCLK register
usb: dwc2: gadget: Add parameters for GREFCLK register
usb: dwc2: Add definitions for new registers
usb: dwc2: Update target (u)frame calculation
usb: dwc2: Add dwc2_gadget_dec_frame_num_by_one() function
usb: dwc2: Add core parameter for service interval support
usb: dwc2: Update registers definitions to support service interval
usb: renesas_usbhs: add support for R-Car E3
dt-bindings: usb: renesas_usbhs: add bindings for r8a77990
usb: renesas_usbhs: rcar3: Use OTG mode for R-Car D3
Revert "usb: renesas_usbhs: set the mode by using extcon state for non-otg channel"
usb: gadget: f_uac2: disable IN/OUT ep if unused
...
The net2280 UDC driver invokes the gadget driver's ->disconnect()
callback routine when the net2280_pullup() routine turns off the D+
pullup. This is now unnecessary, because the gadget core performs the
callback on our behalf. This patch removes the unneeded callback.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The bug would let the usb controller enter partial power down,
which was formally known as hibernate, upon boot if nothing was plugged
in to the port. Partial power down couldn't be exited properly, so any
usb devices plugged in after boot would not be usable.
Before the name change, params.hibernation was false by default, so
_dwc2_hcd_suspend() would skip entering hibernation. With the
rename, _dwc2_hcd_suspend() was changed to use params.power_down
to decide whether or not to enter partial power down.
Since params.power_down is non-zero by default, it needs to be set
to 0 for rockchip devices to restore functionality.
This bug was reported in the linux-usb thread:
REGRESSION: usb: dwc2: USB device not seen after boot
The commit that caused this regression is:
6d23ee9caa
Signed-off-by: SolidHal <hal@halemmerich.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since r8a77990 (R-Car E3) doesn't have VBUS detect pin and
number of ramif is 4, this patch adds a new renesas_usb3_priv
variable for the SoC.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/usb/serial/cypress_m8.c: In function 'cypress_set_termios':
drivers/usb/serial/cypress_m8.c:866:18: warning:
variable 'iflag' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix interrupt-out transfer length which was being set to the
transfer-buffer length rather than the size of the outgoing packet.
Note that no slab data was leaked as the whole transfer buffer is always
cleared before each transfer.
Fixes: 9aa8dae7b1 ("cypress_m8: use usb_fill_int_urb where appropriate")
Signed-off-by: Johan Hovold <johan@kernel.org>
Enable support for cbus gpios on FT232R. The cbus configuration is
stored in one word in the EEPROM at offset 0x0a (byte-offset 0x14) with
the mux config for CBUS0, CBUS1, CBUS2 and CBUS3 in bits 0..3, 4..7,
8..11 and 12..15, respectively.
Tested using FT232RL by configuring one cbus pin at a time.
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop the gpio line names, which cause gpiolib to complain loudly
whenever a second ftdi gpiochip is registered:
gpio gpiochip5: Detected name collision for GPIO name 'CBUS0'
gpio gpiochip5: Detected name collision for GPIO name 'CBUS1'
gpio gpiochip5: Detected name collision for GPIO name 'CBUS2'
gpio gpiochip5: Detected name collision for GPIO name 'CBUS3'
and also prevents the legacy sysfs interface from being used (as the
line names are used as device names whenever they are set):
sysfs: cannot create duplicate filename '/class/gpio/CBUS0'
Until non-unique names are supported by gpiolib (without warnings and
stack dumps), let's leave the gpio lines unnamed.
Signed-off-by: Johan Hovold <johan@kernel.org>
Linus recently observed that if we did not worry about the padding
member in struct siginfo it is only about 48 bytes, and 48 bytes is
much nicer than 128 bytes for allocating on the stack and copying
around in the kernel.
The obvious thing of only adding the padding when userspace is
including siginfo.h won't work as there are sigframe definitions in
the kernel that embed struct siginfo.
So split siginfo in two; kernel_siginfo and siginfo. Keeping the
traditional name for the userspace definition. While the version that
is used internally to the kernel and ultimately will not be padded to
128 bytes is called kernel_siginfo.
The definition of struct kernel_siginfo I have put in include/signal_types.h
A set of buildtime checks has been added to verify the two structures have
the same field offsets.
To make it easy to verify the change kernel_siginfo retains the same
size as siginfo. The reduction in size comes in a following change.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Trivial fix to spelling mistakes in debug warning messages
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/usb/typec/tcpm/tcpm.c: In function 'tcpm_pd_select_pps_apdo':
drivers/usb/typec/tcpm/tcpm.c:2212:39: warning:
variable 'snk_ma' set but not used [-Wunused-but-set-variable]
drivers/usb/typec/tcpm/tcpm.c: In function 'tcpm_pd_build_pps_request':
drivers/usb/typec/tcpm/tcpm.c:2405:37: warning:
variable 'min_mv' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The platform firmware "location" data is used to find port peer
relationships. But firmware is an unreliable source, and there are
real world examples of errors leading to missing or wrong peer
relationships. Debugging this is currently hard.
Exporting the location attribute makes it easier to spot mismatches
between the firmware data and the real world.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new scheme is required just to support legacy low and full-speed
devices. For high speed devices, it will slower the enumeration speed.
So in this patch we try the "old" enumeration scheme first for high speed
devices, and this is what Windows does since Windows 8.
Signed-off-by: Zeng Tao <prime.zeng@hisilicon.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current code mistakenly checks against max current to determine
order but this should be max voltage. This commit fixes the issue
so order is correctly determined, thus avoiding failure based on
a higher voltage PPS APDO having a lower maximum current output,
which is actually valid.
Fixes: 2eadc33f40 ("typec: tcpm: Add core support for sink side PPS")
Cc: <stable@vger.kernel.org>
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the "workaround_for_vbus" is true, the driver will not call
usb_disconnect(). So, since the controller keeps some registers'
value, the driver doesn't re-enumarate suitable speed after
the b-device mode is disabled. To fix the issue, this patch
adds usb_disconnect() calling in renesas_usb3_b_device_write()
if workaround_for_vbus is true.
Fixes: 43ba968b00 ("usb: gadget: udc: renesas_usb3: add debugfs to set the b-device mode")
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added interrupt handler for WkupAlert interrupt.
This interrupt should initiate Remote Wake up.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
WKUP_ALERT interrupt should be unmask when lpm mode is enabled.
This interrupt is asserted when the device is in L1 for the duration
mentioned in GREFCLK.SOF_CNN_WKUP_ALERT. This is used to alert SW to
initiate Remote wake up so that the device resumes in time in order not
to lose sync with the host frame number.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added dwc2_gadget_program_ref_clk function to program GREFCLK
register in device mode.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added ref_clk_per and sof_cnt_wkup_alert parameters in
dwc2_core_params struct and set default values.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
New registers were added to dwc otg core.
GREFCLK - This register used to control ref_clk parameters.
GINTSTS2 - New WKUP_ALERT interrupt was added.
GINTMSK2 - Mask register for GINTSTS2.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In service interval based scheduling target (u)frame must be
set as a last frame in this the service interval.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added dwc2_gadget_dec_frame_num_by_one() function in gadget.c.
This function will be used to calculate descriptor frame number field
value. For service interval mode frame number in descriptor should point
to last (u)frame in the interval.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added core parameter for service interval based scheduling.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added GHWCFG4_SERVICE_INTERVAL_SUPPORTED and
DCTL_SERVICE_INTERVAL_SUPPORTED bits definitions to support
service interval based scheduling.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds support for R-Car E3. This SoC needs to release
the PLL reset by the UGCTRL register like R-Car D3. So, this patch
adds a usbhs_of_match entry for this SoC with
"USBHS_TYPE_RCAR_GEN3_WITH_PLL".
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since R-Car D3 can use OTG mode, this patch changes the UGCTRL2
value to UGCTRL2_USB0SEL_OTG and UGCTRL2_VBUSSEL like other R-Car
Gen3 SoCs.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This reverts commit cd14247d5c.
R-Car D3 can use OTG mode in fact. So, the commit doesn't need anymore.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Via p_chmask/c_chmask the user can define whether uac2 shall support
playback and/or capture. This has only effect on the created ALSA device,
but not on the USB descriptor. This patch adds playback/capture descriptors
dependent on that parameter.
Signed-off-by: Andreas Pape <apape@de.adit-jv.com>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The gadget documentation doesn't state clearly whether a gadget
driver's ->disconnect() callback should be invoked when the D+ pullup
is turned off. Some UDC drivers do this and some don't. This patch
settles the issue by making the core function usb_gadget_disconnect()
issue the callback, so that UDC drivers don't need to worry about it.
A description of the new behavior is added to the function's
kerneldoc. Also, the patch removes a few superseded callbacks from
other core routines.
Future patches will remove the ->disconnect() calls from the UDC
drivers that make them, as they are now unnecessary. Until all those
patches are merged gadget drivers may receive extra ->disconnect()
callbacks, but this should be harmless.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
'optimizations' was misspelled as 'optmizations'. Fixed it. It is a
coding style change which should have no impact on runtime execution of code.
Signed-off-by: Faisal Mehmood <f.m3hm00d@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The name is always non-NULL and then is not used anywhere in this function,
so remove it.
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-usb@vger.kernel.org
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The original implementation from commit b504882da5
("USB: add Freescale high-speed USB SOC device controller driver")
returned NULL on failure and an allocated + initialized struct fsl_udc on
success. The current code introduced in commit 4365831dad
("USB: fsl_usb2_udc: Get max ep number from DCCPARAMS register") only
provides partial initialization as well as returning 0 on success and -1
on failures. The function documentation is updated accordingly.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: 4365831dad ("USB: fsl_usb2_udc: Get max ep number from DCCPARAMS register")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The allocation with fsl_alloc_request() and kmalloc() were unchecked
fixed this up with a NULL check and appropriate cleanup.
Additionally udc->ep_qh_size was reset to 0 on failure of allocation.
Similar udc->phy_mode is initially 0 (as udc_controller was
allocated with kzalloc in fsl_udc_probe()) so reset it to 0 as well
so that this function is side-effect free on failure. Not clear if
this is necessary or sensible as fsl_udc_release() probably can not
be called if fsl_udc_probe() failed - but it should not hurt.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: b504882da5 ("USB: add Freescale high-speed USB SOC device controller driver")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The vbus rise & fall interrupts are used to enable and disable
U3 function of device automatically, this cause some issues when
class driver is initialized as deactivated, and will skip over
software-controlled connect by pullup(), but UDC wants to keep
disconnect until usb_gadget_activate() is called which calls
pullup() if needed. So we disable vbus rise & fall interrupts
and just use pullup() to enable & disable U3 function, and reset
mtu3 state when disconnect instead when vbus fall.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
R-Car Gen3 needs to enable clocks of both host and peripheral.
Since [eo]hci-platform disables the reset(s) when the drivers are
removed, renesas_usbhs driver doesn't work correctly. To fix this
issue, this patch adds multiple clocks management on this
renesas_usbhs driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
R-Car Gen3 needs to deassert resets of both host and peripheral.
Since [eo]hci-platform is possible to assert the reset(s) when
the probing failed, renesas_usbhs driver doesn't work correctly
regardless of finished probing. To fix this issue, this patch adds
reset_control on this renesas_usbhs driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When operating in USB 2.0 speeds (HS/FS), if GUSB2PHYCFG.ENBLSLPM or
GUSB2PHYCFG.SUSPHY is set, it must be cleared before issuing an endpoint
command.
Current implementation only save and restore GUSB2PHYCFG.SUSPHY
configuration. We must save and clear both GUSB2PHYCFG.ENBLSLPM and
GUSB2PHYCFG.SUSPHY settings. Restore them after the command is
completed.
DWC_usb3 3.30a and DWC_usb31 1.90a programming guide section 3.2.2
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When using external vbus supply regulator, it should be enabled
synchronously with PWR bit in HPRT register. This also fixes
unbalanced use of this optional regulator (This can be reproduced
easily when unbinding the driver).
Fixes: 531ef5ebea ("usb: dwc2: add support for host mode external
vbus supply")
Tested-by: Artur Petrosyan <arturp@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc2_vbus_supply_exit() may call regulator_disable(). It shouldn't be
called with interrupts disabled as it might sleep.
This is seen with DEBUG_ATOMIC_SLEEP=y.
Fixes: 531ef5ebea ("usb: dwc2: add support for host mode external
vbus supply")
Tested-by: Artur Petrosyan <arturp@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There's a race with root hub resume, when using external vbus supply.
Root hub gets resumed, but runtime pm autosuspend runs as external vbus
supply isn't enabled. So, host never exit from power down properly.
Initialize vbus external supply before, rater that after hub resume.
Fixes: 531ef5ebea ("usb: dwc2: add support for host mode external
vbus supply")
Tested-by: Artur Petrosyan <arturp@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Move devm_regulator_get_optional() call to probe routine. This avoids
'vbus-supply' regulator to be requested lots of times, upon each call
to dwc2_vbus_supply_init(), e.g. like with runtime pm.
Fixes: 531ef5ebea ("usb: dwc2: add support for host mode external
vbus supply")
Tested-by: Artur Petrosyan <arturp@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Like the omap back-end, we get a link error with CONFIG_EXTCON=m
when building the qcom back-end into the kernel:
drivers/usb/dwc3/dwc3-qcom.o: In function `dwc3_qcom_probe':
dwc3-qcom.c:(.text+0x13dc): undefined reference to `extcon_get_edev_by_phandle'
dwc3-qcom.c:(.text+0x1b18): undefined reference to `devm_extcon_register_notifier'
dwc3-qcom.c:(.text+0x1b9c): undefined reference to `extcon_get_state'
Do the same thing as OMAP and add an explicit dependency on
EXTCON.
Fixes: a4333c3a6b ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The at91sam9rl PMC is not quite the same as the at91sam9g45 one and now has
its own compatible string. Add support for that.
Fixes: 217bace8e548 ("ARM: dts: fix PMC compatible")
Acked-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The driver may sleep in an interrupt handler.
The function call path (from bottom to top) in Linux-4.17 is:
[FUNC] fotg210_ep_queue(GFP_KERNEL)
drivers/usb/gadget/udc/fotg210-udc.c, 744:
fotg210_ep_queue in fotg210_get_status
drivers/usb/gadget/udc/fotg210-udc.c, 768:
fotg210_get_status in fotg210_setup_packet
drivers/usb/gadget/udc/fotg210-udc.c, 949:
fotg210_setup_packet in fotg210_irq (interrupt handler)
To fix this bug, GFP_KERNEL is replaced with GFP_ATOMIC.
If possible, spin_unlock() and spin_lock() around fotg210_ep_queue()
can be also removed.
This bug is found by my static analysis tool DSAC.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Disabling all EP's allow to reset EP's to initial state.
On disconnect disable all EP's instead of just killing
all requests. Because of some platform didn't catch
disconnect event, same stuff added to
dwc2_hsotg_core_init_disconnected() function when USB
reset detected on the bus.
Changed from version 1:
Changed lock acquire flow in dwc2_hsotg_ep_disable()
function.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
DWC3 variant found in Exynos5433 SoCs requires keeping all DRD30/UHOST30
clocks enabled all the time the driver does any access to DWC3 registers,
otherwise external abort happens. So far DWC3 hardware module worked with
samsung,exynos5250-dwusb3 compatible only by luck when built into kernel:
all DRD30 clocks were left enabled by bootloader and later kept enabled
by the DRD PHY driver. However, if one tried to use Exnos DWC3 driver as
a module or performed system suspend/resume cycle, external abort
happened. This patch finally fixes this issue.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add per-variant list of clocks and manage them all together in
the single array. This is a preparation for adding new variants
of Exynos SoCs. No functional changes for existing Exynos SoCs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
All supported Exynos variants provide respective generic PHY framework
based drivers for controlling USB PHYs, so there is no point
creating fake USB PHYs based on platform devices. While removing useless
code, remove calls to runtime PM, which have no effect.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Trivial fix to spelling mistake in dev_dbg message
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Clang warns when multiple pairs of parentheses are used for a single
conditional statement.
drivers/usb/gadget/udc/mv_udc_core.c:188:33: warning: equality
comparison with extraneous parentheses [-Wparentheses-equality]
while ((curr_dqh->curr_dtd_ptr == curr_dtd->td_dma)) {
~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~
drivers/usb/gadget/udc/mv_udc_core.c:188:33: note: remove extraneous
parentheses around the comparison to silence this warning
while ((curr_dqh->curr_dtd_ptr == curr_dtd->td_dma)) {
~ ^ ~
drivers/usb/gadget/udc/mv_udc_core.c:188:33: note: use '=' to turn this
equality comparison into an assignment
while ((curr_dqh->curr_dtd_ptr == curr_dtd->td_dma)) {
^~
=
1 warning generated.
Link: https://github.com/ClangBuiltLinux/linux/issues/120
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch removes a set but unused variable in hcd.c.
Fixes gcc warning:
variable ‘data_fifo’ set but not used [-Wunused-but-set-variable]
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Joshua Abraham <j.abraham1776@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This reverts commit 8ada211d03.
R-Car D3 can use OTG mode in fact. So, the commit doesn't need anymore.
In other words, like other R-Car Gen3 SoCs, R-Car D3 can change the mode
by using the phy-rcar-gen3-usb2 driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Trivial fix to spelling mistakes in debug warning messages
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Give USB3 devices a better chance to enumerate at USB3 speeds if
they are connected to a suspended host.
Porting from "671ffdff5b13 xhci: resume USB 3 roothub first"
Cc: <stable@vger.kernel.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The workaround for missing CAS bit is also needed for xHC on Intel
sunrisepoint PCH. For more details see:
Intel 100/c230 series PCH specification update Doc #332692-006 Errata #8
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the ACM TTY port is disconnected, the URBs it uses must be killed, and
then the buffers must be freed. Unfortunately a previous refactor removed
the code freeing the buffers because it looked extremely similar to the
code killing the URBs.
As a result, there were many new leaks for each plug/unplug cycle of a
CDC-ACM device, that were detected by kmemleak.
Restore the missing code, and the memory leak is removed.
Fixes: ba8c931ded ("cdc-acm: refactor killing urbs")
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some device-id patches for 4.19-rc7.
Some Quectel modems have a vendor command which can be used to disable
certain interfaces in their configurations, but unlike some other modems
this also causes the interface numbers to change. These patches allow us
to support all such interface permutations at least for the Quectel
EP06.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=82HD
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.19-rc7' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.19-rc7
Here are some device-id patches for 4.19-rc7.
Some Quectel modems have a vendor command which can be used to disable
certain interfaces in their configurations, but unlike some other modems
this also causes the interface numbers to change. These patches allow us
to support all such interface permutations at least for the Quectel
EP06.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-4.19-rc7' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: simple: add Motorola Tetra MTP6550 id
USB: serial: option: add two-endpoints device-id flag
USB: serial: option: improve Quectel EP06 detection
Fix uninitialized symbol 'actual' in function
usbtmc_ioctl_abort_bulk_in_tag().
When symbol 'actual' is not initialized and usb_bulk_msg() fails,
the subsequent kernel debug message shows invalid data.
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Fixes: cbe743f133 ("usb: usbtmc: Fix ioctl USBTMC_IOCTL_ABORT_BULK_IN")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix uninitialized symbol 'actual' in function usbtmc_ioctl_clear.
When symbol 'actual' is not initialized and usb_bulk_msg() fails,
the subsequent kernel debug message shows a random value.
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Fixes: dfee02ac4b ("usb: usbtmc: Fix ioctl USBTMC_IOCTL_CLEAR")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix uninitialized symbol 'actual' in function usbtmc_read.
When symbol 'actual' is not initialized and usb_bulk_msg() fails,
the subsequent kernel debug message shows a random value.
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Fixes: d7604ff0dc ("usb: usbtmc: Optimize usbtmc_read")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kernel memory is allocated twice in new function
usbtmc_ioctl_request and creates a memory leak.
This fix removes the superfluous kmalloc().
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Fixes: 658f24f452 ("usb: usbtmc: Add ioctl for generic requests on control")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for R-Car E3. This SoC needs to release
the PLL reset by the UGCTRL register like R-Car D3. So, this patch
adds a usbhs_of_match entry for this SoC with
"USBHS_TYPE_RCAR_GEN3_WITH_PLL".
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since R-Car D3 can use OTG mode, this patch changes the UGCTRL2
value to UGCTRL2_USB0SEL_OTG and UGCTRL2_VBUSSEL like other R-Car
Gen3 SoCs.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit cd14247d5c.
R-Car D3 can use OTG mode in fact. So, the commit doesn't need anymore.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 8ada211d03.
R-Car D3 can use OTG mode in fact. So, the commit doesn't need anymore.
In other words, like other R-Car Gen3 SoCs, R-Car D3 can change the mode
by using the phy-rcar-gen3-usb2 driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 1cbd53c8cd ("usb: core: introduce per-port over-current
counters") usb ports expose a sysfs value 'over_current_count'
to user space. This value on its own is not very useful as it requires
manual polling.
As a solution, fire a udev event from the usb hub device that specifies
the values 'OVER_CURRENT_PORT' and 'OVER_CURRENT_COUNT' that indicate
the path of the usb port where the over-current event occurred and the
value of 'over_current_count' in sysfs. Additionally, call
sysfs_notify() so the sysfs value supports poll().
Signed-off-by: Jon Flatley <jflat@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the controller is configured for a fixed power role (Source
only or Sink only), attach does not proceed within the TCPM state
machine as there is no CC event generated by this driver to update
the CC line status.
To rectify this, when CC is configured as Source or Sink we now
make use of the hardware's automatic fixed Source or Sink
toggling mechanism, which detects attaches in the same way as for
DRP toggling. In this way the result of toggling is handled in the
same way by the 'fusb302_handle_togdone()' function, and CC events
are generated as expected for TCPM allowing a contract to be
established.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's a typo in the enum name of the 'OFF' state for toggling
(TOGGLINE instead of TOGGLING). This commit resolves that trivial
spelling inconsistency.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When USB bus host controller root hub resumes from autosuspend,
it immediately tries to enter auto-suspend, but there can be a
scenario when root hub is resuming its usb2 ports, in that particular
case USB host controller auto suspend fails since it is busy
to resuming its usb2 ports.
This makes multiple failed cycles of auto-suspend until all usb2
ports of host controller root hub do not resume.
This patch uses USB core framework usb_hcd_start_port_resume,
usb_hcd_end_port_resume API's in order to autoresume/autosuspend
root hub properly.
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The XUSB firmware header is in little endian byte order, so make the
fields __le32 and __le16 instead of u32 and u16 to avoid warnings from
sparse when the fields are used with the endian-aware __le32_to_cpu()
and __le16_to_cpu() accessors, respectively.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xhci controller on Alpine and Titan Ridge keeps the whole thunderbolt
awake if the host controller is not allowed tp sleep.
This is the case even if no USB devices are connected to the host.
Because of this bigger impact, allow runtime pm as default for these xhci
controllers in the driver.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use soft retry to recover from a USB Transaction Errors that are caused by
temporary error conditions. The USB device is not aware that the xHC
has halted the endpoint, and will be waiting for another retry
A Soft Retry perform additional retries and recover from an error which has
caused the xHC to halt an endpoint.
Soft retry has some limitations:
Soft Retry attempts shall not be performed on Isoch endpoints
Soft Retry attempts shall not be performed if the device is behind a TT in
a HS Hub
Software shall limit the number of unsuccessful Soft Retry attempts to
prevent an infinite loop.
For more details on Soft retry see xhci specs 4.6.8.1
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TPL support is used to identify targeted devices during
EH2.0 and EH3.0 certification test, the user can add "tpl-support"
at dts to enable this feature.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Supports SSP scheduling only for SSP device directly connected
to root hub but not through external USB3 gen2 hub which need
use a new scheduling way.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mainly improve SuperSpeed ISOC bandwidth in last microframe,
and LowSpeed/FullSpeed IN INT/ISOC bandwidth in split and
idle microframes by introduing a bandwidth budget table;
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the interval equal zero, needn't round up to power of two
for the number of packets in each ESIT, so fix it.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make use of maximum ESIT payload of endpoint context to calculate
the number of packets to send in each ESIT
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's dangerous to use empty code define.
Furthermore it lead to the following warning:
"suggest braces around empty body in an « else » statement"
So let's replace emptyness by "do {} while(0)"
Furthermore, as suggested by Joe Perches, rename the macro to INCR.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the quest to remove all stack VLA usage from the kernel[1], this
replaces struct crypto_skcipher and SKCIPHER_REQUEST_ON_STACK() usage
with struct crypto_sync_skcipher and SYNC_SKCIPHER_REQUEST_ON_STACK(),
which uses a fixed stack size.
[1] https://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.com
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: "Gustavo A. R. Silva" <gustavo@embeddedor.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch allows using the CBUS pins of FT-X devices as GPIO in CBUS
bitbanging mode. There is no conflict between the GPIO and VCP
functionality in this mode. Tested on FT230X and FT231X.
As there is no way to request the current CBUS register configuration
from the device, all CBUS pins are set to a known state when the first
GPIO is requested. This allows using libftdi to set the GPIO pins
before loading this module for UART functionality, a behavior that
existing applications might be relying upon (though no specific case
is known to the authors of this patch).
Signed-off-by: Karoly Pados <pados@pados.hu>
[ johan: minor style changes ]
Signed-off-by: Johan Hovold <johan@kernel.org>
The driver uses the %d format to print unsigned int values. The correct
format is %u. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Tested-by: Paul Elder <paul.elder@ideasonboard.com>
Several macros used to define attributes and their access functions take
multiple arguments to specify endianness and string conversion
functions, based on the size of the attribute. This can be simplified by
passing the number of bits explicitly, and constructing the name of the
functions internally.
The UVCG_OPTS_ATTR macro can be simplified further as all fields it
deals with are unsigned int.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Tested-by: Paul Elder <paul.elder@ideasonboard.com>
USB descriptors are stored in little endian, requiring the use of
conversion macros. Those macros are incorrectly used for values stored
in native endian structures within the driver. Operation on big endian
platforms is thus broken. Fix it by removing the conversion macros where
they're not needed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Tested-by: Paul Elder <paul.elder@ideasonboard.com>
The function is never called, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Adding device context to the kernel log messages make them more useful.
Add new uvcg_* macros based on dev_*() that print both the gadget device
name and the function name.
While at it, remove a commented out printk statement and an unused
printk-based macro.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Tested-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
When USB requests for video data fail to be submitted, the driver
signals a problem to the host by halting the video streaming endpoint.
This is only valid in bulk mode, as isochronous transfers have no
handshake phase and can't thus report a stall. The usb_ep_set_halt()
call returns an error when using isochronous endpoints, which we happily
ignore, but some UDCs complain in the kernel log. Fix this by only
trying to halt the endpoint in bulk mode.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Tested-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
USB requests for video data are queued from two different locations in
the driver, with the same code block occurring twice. Factor it out to a
function.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Tested-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
There is an issue where the host is unable to tell the gadget what frame
rate it wants if the dwFrameIntervals in the interface descriptors are
not in ascending order. This means that when instantiating a uvc gadget
via configfs the user must make sure the dwFrameIntervals are in
ascending order.
Instead of silently failing the breaking of this rule, we sort the
dwFrameIntervals upon writing to configfs.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
While checks are in place to avoid attributes and children of a format
being manipulated after the format is linked into the streaming header,
the linked flag was never actually set, invalidating the protections.
Update the flag as appropriate in the header link calls.
Signed-off-by: Joel Pepper <joel.pepper@rwth-aachen.de>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
- Add bFrameIndex as a UVCG_FRAME_ATTR_RO for each frame size.
- Automatically assign ascending bFrameIndex to each frame in a format.
Before all "bFrameindex" attributes were set to "1" with no way to
configure the gadget otherwise. This resulted in the host always
negotiating for bFrameIndex 1 (i.e. the first frame size of the gadget).
After the negotiation the host driver will set the user or application
selected frame size, while the gadget is actually set to the first frame
size.
Now, when the containing format is linked into the streaming header,
iterate over all child frame descriptors and assign ascending indices.
The automatically assigned indices can be read from the new read only
bFrameIndex configfs attribute in each frame descriptor item.
Signed-off-by: Joel Pepper <joel.pepper@rwth-aachen.de>
[Simplified documentation, renamed function, blank space update]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
The UVC format description are numbered using the descriptor's
bFormatIndex field. The index is used in UVC requests, and is thus
needed to handle requests in userspace. Make it dynamically discoverable
by exposing it in a bFormatIndex configfs attribute of the uncompressed
and mjpeg format config items.
The bFormatIndex value exposed through the attribute is stored in the
config item private data. However, that value is never set: the driver
instead computes the bFormatIndex value when linking the stream class
header in the configfs hierarchy and stores it directly in the class
descriptors in a separate structure. In order to expose the value
through the configfs attribute, store it in the config item private data
as well. This results in a small code simplification.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
The video control and video streaming interface numbers are needed in
the UVC gadget userspace stack to reply to UVC requests. They are
hardcoded to fixed values at the moment, preventing configurations with
multiple functions.
To fix this, make them dynamically discoverable by userspace through
read-only configfs attributes in <function>/control/bInterfaceNumber and
<function>/streaming/bInterfaceNumber respectively.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
The UVC configfs implementation creates all groups as global static
variables. This prevents creation of multiple UVC function instances,
as they would all require their own configfs group instances.
Fix this by allocating all groups dynamically. To avoid duplicating code
around, extend the config_item_type structure with group name and
children, and implement helper functions to create children
automatically for most groups.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Some of the .allow_link() and .drop_link() operations implementations
call config_group_find_item() and then leak the reference to the
returned item. Fix this by dropping those references where needed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Trivial fix to spelling mistake in dev_dbg message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fixed errors spaces required around the for loop '=' , ';' and '<'
in drivers/usb/storage/isd200.c
Signed-off-by: Jagdish Tirumala <t.jag587@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Moving all the drivers that depend on the Port Controller
Manager under a new directory drivers/usb/typec/tcpm/ and
making Guenter Roeck the designated reviewer of that code.
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The debugfs needs to be initialized as the last step in
probe in this case. The struct dentry *rootdir can't be
pointing to anything unless driver probe really finishes
successfully.
It is also not necessary to clear the i2c clientdata if the
probe fails, so removing the extra label used for that.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is not possible to use the parent of the port device when
requesting mux handles as the parent may be a multiport USB
Type-C or PD controller. The muxes must be assigned to the
ports, not the controllers.
This will also move the requesting of the muxes after the
port device is initialized.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Functions typec_mux_get() and typec_switch_get() already
make sure that the mux device reference count is
incremented, but the same must be done to the driver module
as well to prevent the drivers from being unloaded in the
middle of operation.
This fixes a potential "BUG: unable to handle kernel paging
request at ..." from happening.
Fixes: 93dd2112c7 ("usb: typec: mux: Get the mux identifier from function parameter")
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Applying dynamic usbcore quirks in early booting when the slab is
not yet ready would cause kernel panic of null pointer dereference
because the quirk_count has been counted as 1 while the quirk_list
was failed to allocate.
i.e.,
[ 1.044970] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 1.044995] IP: [<ffffffffb0953ec7>] usb_detect_quirks+0x88/0xd1
[ 1.045016] PGD 0
[ 1.045026] Oops: 0000 [#1] PREEMPT SMP
[ 1.046986] gsmi: Log Shutdown Reason 0x03
[ 1.046995] Modules linked in:
[ 1.047008] CPU: 0 PID: 81 Comm: kworker/0:3 Not tainted 4.4.154 #28
[ 1.047016] Hardware name: Google Coral/Coral, BIOS Google_Coral.10068.27.0 12/04/2017
[ 1.047028] Workqueue: usb_hub_wq hub_event
[ 1.047037] task: ffff88017a321c80 task.stack: ffff88017a384000
[ 1.047044] RIP: 0010:[<ffffffffb0953ec7>] [<ffffffffb0953ec7>] usb_detect_quirks+0x88/0xd1
To tackle this odd, let's balance the quirk_count to 0 when the kcalloc
call fails, and defer the quirk setting into a lower level callback
which ensures that the kernel memory management has been initialized.
Fixes: 027bd6cafd ("usb: core: Add "quirks" parameter for usbcore")
Signed-off-by: Harry Pan <harry.pan@intel.com>
Acked-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes potential "BUG: unable to handle kernel paging
request at ..." from happening.
Fixes: fde0aa6c17 ("usb: common: Small class for USB role switches")
Cc: <stable@vger.kernel.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trivial fix to spelling mistake in dev_dbg message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is code in the .remove() hook to handle the drvdata
being NULL, for good reasons: it is never set, so it will
always be NULL. As I moved code around, static checkers
start complaining.
Instead of this, make sure to always set it on successful
probe so we can always dereference it on the remove path.
Use the platform_device_[set|get]_drvdata() since this is
a platform device.
Fixes: ffa8a31b5b ("usb: host: fotg2: add silicon clock handling")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
R-Car Gen3 needs to enable clocks of both host and peripheral.
Since [eo]hci-platform disables the reset(s) when the drivers are
removed, renesas_usbhs driver doesn't work correctly. To fix this
issue, this patch adds multiple clocks management on this
renesas_usbhs driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
R-Car Gen3 needs to deassert resets of both host and peripheral.
Since [eo]hci-platform is possible to assert the reset(s) when
the probing failed, renesas_usbhs driver doesn't work correctly
regardless of finished probing. To fix this issue, this patch adds
reset_control on this renesas_usbhs driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB audio class 3.0 specification introduced many significant
changes like
- new power domains, support for LPM/L1
- new cluster descriptor
- new high capability and class-specific string descriptors
- BADD profiles
- ... and many other things (check spec from link below:
http://www.usb.org/developers/docs/devclass_docs/USB_Audio_v3.0.zip)
Now that UAC3 is supported in linux, choose UAC3
configuration for audio if the device supports it.
Selecting this configuration will enable the system to
save power by leveraging the new power domains and LPM L1
capability and also support new codec types and data formats
for consumer audio applications.
Signed-off-by: Saranya Gopal <saranya.gopal@intel.com>
Reviewed-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use a proper PHY driver, instead of hooks to a board support package.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is done do that it could be enabled alongside other platform EHCI
glue drivers on multiplatform kernels.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As all the properties of the usbtmc driver can now be
controlled on a per file descriptor basis by ioctl functions
the sysfs interface is of limited use.
We are not aware about applications that are using the sysfs
parameter TermChar, TermCharEnabled or auto_abort.
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add ioctl USBTMC_IOCTL_API_VERSION to get current API version
of usbtmc driver.
This is to allow an instrument library to determine whether
the driver API is compatible with the implementation.
The API may change in future versions. Therefore the macro
USBTMC_API_VERSION should be incremented when changing tmc.h
with new flags, ioctls or when changing a significant behavior
of the driver.
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use common timeout macro USB_CTRL_GET_TIMEOUT (=5s) for all
usb_control_msg() function calls.
The macro USBTMC_TIMEOUT should only be used as default value for
Bulk IN/OUT transfers.
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add parameter 'tag' to function usbtmc_ioctl_abort_bulk_out_tag()
for future versions.
Use USBTMC_BUFSIZE (4k) instead of USBTMC_SIZE_IOBUFFER (2k).
Using USBTMC_SIZE_IOBUFFER is deprecated.
Insert a sleep of 50 ms between subsequent
CHECK_ABORT_BULK_OUT_STATUS control requests to avoid stressing
the instrument with repeated requests.
Use common macro USB_CTRL_GET_TIMEOUT instead of USBTMC_TIMEOUT.
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add parameter 'tag' to function usbtmc_ioctl_abort_bulk_in_tag()
for future versions.
Remove calculation of max_size (=wMaxPacketSize) and wrong
condition (actual == max_size) in while loop. An abort operation
should always flush the complete Bulk-IN until a short packet is
received.
Return error code ENOMSG when transfer (specified by given tag)
is not in progress and device returns code
USBTMC_STATUS_TRANSFER_NOT_IN_PROGRESS.
Use USBTMC_BUFSIZE (4k) instead of USBTMC_SIZE_IOBUFFER (2k).
Using USBTMC_SIZE_IOBUFFER is deprecated.
Use common macro USB_CTRL_GET_TIMEOUT instead of USBTMC_TIMEOUT.
Check only bit 0 (field bmAbortBulkIn) of the
CHECK_ABORT_BULK_IN_STATUS response, since other bits are reserved
and can change in future versions.
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove calculation of max_size (=wMaxPacketSize) and wrong
condition (actual == max_size) in while loop. A device clear
should always flush the complete Bulk-IN FIFO.
Insert a sleep of 50 ms between subsequent CHECK_CLEAR_STATUS
control requests to avoid stressing the instrument with
repeated requests.
Some instruments need time to cleanup internal I/O buffers.
Polling and nonbraked requests slow down the response time of
devices.
Use USBTMC_BUFSIZE (4k) instead of USBTMC_SIZE_IOBUFFER (2k).
Using USBTMC_SIZE_IOBUFFER is deprecated.
Check only bit 0 (field bmClear) of the CHECK_CLEAR_STATUS
response, since other bits are reserved and can change in
future versions.
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use new usbtmc_generic_read function to maximize bandwidth
during long data transfer. Also fix reading of zero length
packet (ZLP) or trailing short packet.
The maximum input transfer size is limited to INT_MAX (=2GB).
Also remove redundant return in send_request_dev_dep_msg_in().
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use new usbtmc_generic_write function to maximize bandwidth
during long data transfer.
The maximum output transfer size is limited to INT_MAX (=2GB).
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add ioctl USBTMC_IOCTL_AUTO_ABORT to configure auto_abort for
each specific file handle.
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
add ioctl USBTMC_IOCTL_MSG_IN_ATTR that returns the specific
bmTransferAttributes field of the last DEV_DEP_MSG_IN Bulk-IN
header. This header is received by the read() function. The
meaning of the (u8) bitmap bmTransferAttributes is:
Bit 0 = EOM flag is set when the last transfer of a USBTMC
message is received.
Bit 1 = is set when the last byte is a termchar (e.g. '\n').
Note that this bit is always zero when the device does not support
the termchar feature or when termchar detection is not enabled
(see ioctl USBTMC_IOCTL_CONFIG_TERMCHAR).
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wait until an SRQ (service request) is received on the interrupt pipe
or until the given period of time is expired. In contrast to the
poll() function this ioctl does not return when other (a)synchronous
I/O operations fail with EPOLLERR.
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Submitted urbs are not allowed when system is suspended.
Thus the submitted urb waiting at interrupt pipe is killed
during suspend callback and submitted again when system resumes.
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ioctl USBTMC_IOCTL_CLEANUP_IO kills all submitted urbs to OUT
and IN bulk, and clears all received data from IN bulk. Internal
transfer counters and error states are reset.
An application should use this ioctl after an asnychronous transfer
was canceled and/or error handling has finished.
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ioctl USBTMC_IOCTL_CANCEL_IO stops and kills all flying urbs of
last USBTMC_IOCTL_READ and USBTMC_IOCTL_WRITE function calls.
A subsequent call to USBTMC_IOCTL_READ or
USBTMC_IOCTL_WRITE_RESULT returns -ECANCELED with
information about current transferred data.
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USBTMC_IOCTL_READ call provides for generic synchronous and
asynchronous reads on bulk IN to implement vendor specific library
routines.
Depending on transfer_size the function submits one or more urbs (up
to 16) each with a size of up to 4kB.
The flag USBTMC_FLAG_IGNORE_TRAILER can be used when the transmission
size is already known. Then the function does not truncate the
transfer_size to a multiple of 4 kB, but does reserve extra space
to receive the final short or zero length packet. Note that the
instrument is allowed to send up to wMaxPacketSize - 1 bytes at the
end of a message to avoid sending a zero length packet.
With flag USBTMC_FLAG_ASYNC the ioctl is non blocking. When no
received data is available, the read function submits as many urbs as
needed to receive transfer_size bytes. However the number of flying
urbs (=4kB) is limited to 16 even with subsequent calls of this ioctl.
Returns -EAGAIN when non blocking and no data is received.
Signals EPOLLIN | EPOLLRDNORM when asynchronous urbs are ready to
be read.
In non blocking mode the usbtmc_message.message pointer may be NULL
and the ioctl just submits urbs to initiate receiving data. However if
data is already available due to a previous non blocking call the ioctl
will return -EINVAL when the message pointer is NULL.
This ioctl does not support compatibility for 32 bit
applications running on 64 bit systems. However all other
convenient ioctls of the USBTMC driver can still be used in 32
bit applications as well. Note that 32 bit applications running
on 32 bit target systems are not affected by this limitation.
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ioctl USBTMC_IOCTL_WRITE_RESULT copies current out_transfer_size
to given __u32 pointer and returns current out_status of the last
(asnynchronous) USBTMC_IOCTL_WRITE call.
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new ioctl USBTMC_IOCTL_WRITE sends a generic message to bulk OUT.
This ioctl is used for vendor specific or asynchronous I/O as well.
The message is split into chunks of 4k (page size).
Message size is aligned to 32 bit boundaries.
With flag USBTMC_FLAG_ASYNC the ioctl is non blocking.
With flag USBTMC_FLAG_APPEND additional urbs are queued and
out_status/out_transfer_size is not reset. EPOLLOUT | EPOLLWRNORM
is signaled when all submitted urbs are completed.
Flush flying urbs when file handle is closed or device is
suspended or reset.
This ioctl does not support compatibility for 32 bit
applications running on 64 bit systems. However all other
convenient ioctls of the USBTMC driver can still be used in 32
bit applications as well. Note that 32 bit applications running
on 32 bit target systems are not affected by this limitation.
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add USBTMC_IOCTL_CTRL_REQUEST to send arbitrary requests on the
control pipe. Used by specific applications of IVI Foundation,
Inc. to implement VISA API functions: viUsbControlIn/Out.
The maximum length of control request is set to 4k.
This ioctl does not support compatibility for 32 bit
applications running on 64 bit systems. However all other
convenient ioctls of the USBTMC driver can still be used in 32
bit applications as well. Note that 32 bit applications running
on 32 bit target systems are not affected by this limitation.
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This update populates the tcpc handle's fwnode pointer with the
child usb-connector node, if it exists, so that TCPM can perform
generic property handling to define the ports capabilities.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_find_alt_setting() takes a pointer to a struct usb_host_config as
an argument; it searches for an interface with specified interface and
alternate setting numbers in that config. However, it crashes if the
usb_host_config pointer argument is NULL.
Since this is a general-purpose routine, available for use in many
places, we want to to be more robust. This patch makes it return NULL
whenever the config argument is NULL.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: syzbot+19c3aaef85a89d451eac@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The syzbot fuzzing project found a use-after-free bug in the USB
core. The bug was caused by usbfs not unbinding from an interface
when the USB device file was closed, which led another process to
attempt the unbind later on, after the private data structure had been
deallocated.
The reason usbfs did not unbind the interface at the appropriate time
was because it thought the interface had never been claimed in the
first place. This was caused by the fact that
usb_driver_claim_interface() does not clean up properly when
device_bind_driver() returns an error. Although the error code gets
passed back to the caller, the iface->dev.driver pointer remains set
and iface->condition remains equal to USB_INTERFACE_BOUND.
This patch adds proper error handling to usb_driver_claim_interface().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: syzbot+f84aa7209ccec829536f@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_driver_claim_interface() disables and re-enables Link Power
Management, but it shouldn't do either one, for the reasons listed
below. This patch removes the two LPM-related function calls from the
routine.
The reason for disabling LPM in the analogous function
usb_probe_interface() is so that drivers won't have to deal with
unwanted LPM transitions in their probe routine. But
usb_driver_claim_interface() doesn't call the driver's probe routine
(or any other callbacks), so that reason doesn't apply here.
Furthermore, no driver other than usbfs will ever call
usb_driver_claim_interface() unless it is already bound to another
interface in the same device, which means disabling LPM here would be
redundant. usbfs doesn't interact with LPM at all.
Lastly, the error return from usb_unlocked_disable_lpm() isn't handled
properly; the code doesn't clean up its earlier actions before
returning.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: 8306095fd2 ("USB: Disable USB 3.0 LPM in critical sections.")
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we filter flags before they reach the core we need to generate our
own warnings.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: 0cb54a3e47 ("USB: debugging code shouldn't alter control flow")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Requesting a ZERO_PACKET or not is sensible only for output.
In the input direction the device decides.
Likewise accepting short packets makes sense only for input.
This allows operation with panic_on_warn without opening up
a local DOS.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-by: syzbot+843efa30c8821bd69f53@syzkaller.appspotmail.com
Fixes: 0cb54a3e47 ("USB: debugging code shouldn't alter control flow")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 6e22e3af7b.
The bug the patch describes to, has been already fixed in commit
2df6948428 ("USB: cdc-wdm: don't enable interrupts in USB-giveback")
so need to this, revert it.
Fixes: 6e22e3af7b ("usb: cdc-wdm: Fix a sleep-in-atomic-context bug in service_outstanding_interrupt()")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TI AM335x CPPI 4.1 module uses a single register bit for CPPI interrupts
in both musb controllers. So disabling the CPPI irq in one musb driver
breaks the other musb module.
Since musb is already disabled before tearing down dma controller in
musb_remove(), it is safe to not disable CPPI irq in
musb_dma_controller_destroy().
Fixes: 255348289f ("usb: musb: dsps: Manage CPPI 4.1 DMA interrupt in DSPS")
Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At OTG work running time, it's possible that several events need to be
addressed (e.g. ID and VBUS events). The current implementation handles
only one event at a time which leads to ignoring the other one. Fix it.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The ChipIdea IRQ is disabled before scheduling the otg work and
re-enabled on otg work completion. However if the job is already
scheduled we have to undo the effect of disable_irq int order to
balance the IRQ disable-depth value.
Fixes: be6b0c1bd0 ("usb: chipidea: using one inline function to cover queue work operations")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Some hardware implementations require to configure pins differently
according to the USB role (host/device), this can be an update of the
pins routing or a simple GPIO value change.
This patch introduces new optional "host" and "device" pinctrls.
If these pinctrls are defined by the device, they are respectively
selected on host/device role start.
If a default pinctrl exist, it is restored on host/device role stop.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The SPDX-License-Identifier is set to GPL-2.0+, which correspond to
MODULE_LICENSE "GPL".
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
When initializing the USB subsystem before starting the kernel,
OTG overcurrent detection is disabled. In case the OTG polarity of
overcurrent is low active, the overcurrent detection is never enabled
again and events cannot be reported as expected. Because imx usb
overcurrent polarity is low active by default, only detection needs
to be enable in usbmisc init function.
Signed-off-by: Nicolas Adell <nicolas.adell@actia.fr>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Use preprocessor conditionals for CONFIG_PM and CONFIG_PM_SLEEP is
not necessary since SET_SYSTEM_SLEEP_PM_OPS and SET_RUNTIME_PM_OPS does
that internally.
It is also the preferred way according to our coding style guidelines.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The UVC configfs implementation is large and difficult to navigate. Add
a bit more air to the code to make it easier to read.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Various configfs groups (represented by config_group) are wrapped in
structures that they're the only member of. This allows adding other
data fields to groups, but it unnecessarily makes the code more complex.
Remove the outer structures and use config_group directly to simplify
the code. Groups can still be wrapped individually in the future if
other data fields need to be added.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
These ioctls never reach driver's ->ioctl() - tty_ioctl() handles
them on its own. ->tiocm[gs]et() is what actually gets called,
and mos7720 provides those, with results equivalent to what the
unreachable code would be doing when called.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Allow matching on interfaces having two endpoints by adding a new
device-id flag.
This allows for the handling of devices whose interface numbers can
change (e.g. Quectel EP06) to be contained in the device-id table.
Tested-by: Kristian Evensen <kristian.evensen@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The Quectel EP06 (and EM06/EG06) LTE modem supports updating the USB
configuration, without the VID/PID or configuration number changing.
When the configuration is updated and interfaces are added/removed, the
interface numbers are updated. This causes our current code for matching
EP06 not to work as intended, as the assumption about reserved
interfaces no longer holds. If for example the diagnostic (first)
interface is removed, option will (try to) bind to the QMI interface.
This patch improves EP06 detection by replacing the current match with
two matches, and those matches check class, subclass and protocol as
well as VID and PID. The diag interface exports class, subclass and
protocol as 0xff. For the other serial interfaces, class is 0xff and
subclass and protocol are both 0x0.
The modem can export the following devices and always in this order:
diag, nmea, at, ppp. qmi and adb. This means that diag can only ever be
interface 0, and interface numbers 1-5 should be marked as reserved. The
three other serial devices can have interface numbers 0-3, but I have
not marked any interfaces as reserved. The reason is that the serial
devices are the only interfaces exported by the device where subclass
and protocol is 0x0.
QMI exports the same class, subclass and protocol values as the diag
interface. However, the two interfaces have different number of
endpoints, QMI has three and diag two. I have added a check for number
of interfaces if VID/PID matches the EP06, and we ignore the device if
number of interfaces equals three (and subclass is set).
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Dan Williams <dcbw@redhat.com>
[ johan: drop uneeded RSVD(5) for ADB ]
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Today kernel threads never dequeue siginfo so it is pointless to
enqueue siginfo for them. The usb gadget mass storage driver goes
one farther and uses SEND_SIG_FORCED to guarantee that no siginfo is
even enqueued.
Generalize the optimization of the usb mass storage driver and never
perform an unnecessary allocation when delivering signals to kthreads.
Switch the mass storage driver from sending signals with
SEND_SIG_FORCED to SEND_SIG_PRIV. As using SEND_SIG_FORCED is now
unnecessary.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
None of the callers use the it so remove it.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
In commit ed194d1367 ("usb: core: remove local_irq_save() around
->complete() handler") I removed the only user of the flags variable and
forgot to remove the variable, leading to warning because it is unused
now.
Remove the unused variable.
Fixes: ed194d1367 ("usb: core: remove local_irq_save() around ->complete() handler")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit a81cf9799a.
The patch causes a regression, which I cannot find the reason for.
So let's revert for now, as a revert hurts only performance.
Original report:
I was trying to resolve the problem with Oliver but we don't get any conclusion
for 5 months, so I am now sending this to mail list and cdc_acm authors.
I am using simple request-response protocol to obtain the boiller parameters
in constant intervals.
A simple one transaction is:
1. opening the /dev/ttyACM0
2. sending the following 10-bytes request to the device:
unsigned char req[] = {0x02, 0xfe, 0x01, 0x05, 0x08, 0x02, 0x01, 0x69, 0xab, 0x03};
3. reading response (frame of 74 bytes length).
4. closing the descriptor
I am doing this transaction with 5 seconds intervals.
Before the bad commit everything was working correctly: I've got a requests and
a responses in a timely manner.
After the bad commit more time I am using the kernel module, more problems I have.
The graph [2] is showing the problem.
As you can see after module load all seems fine but after about 30 minutes I've got
a plenty of EAGAINs when doing read()'s and trying to read back the data.
When I rmmod and insmod the cdc_acm module again, then the situation is starting
over again: running ok shortly after load, and more time it is running, more EAGAINs
I have when calling read().
As a bonus I can see the problem on the device itself:
The device is configured as you can see here on this screen [3].
It has two transmision LEDs: TX and RX. Blink duration is set for 100ms.
This is a recording before the bad commit when all is working fine: [4]
And this is with the bad commit: [5]
As you can see the TX led is blinking wrongly long (indicating transmission?)
and I have problems doing read() calls (EAGAIN).
Reported-by: Mariusz Bialonczyk <manio@skyboo.net>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: a81cf9799a ("cdc-acm: implement put_char() and flush_chars()")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since renesas_usb3 udc driver calls usb_of_get_companion_dev()
which is on usb/core/of.c, build error like below happens if we
disable CONFIG_USB because the usb/core/ needs CONFIG_USB:
ERROR: "usb_of_get_companion_dev" [drivers/usb/gadget/udc/renesas_usb3.ko] undefined!
According to the usb/gadget/Kconfig, "NOTE: Gadget support
** DOES NOT ** depend on host-side CONFIG_USB !!".
So, to fix the issue, this patch changes the usb_of_get_companion_dev()
place from usb/core/of.c to usb/common/common.c to be called by both
host and gadget.
Reported-by: John Garry <john.garry@huawei.com>
Fixes: 39facfa01c ("usb: gadget: udc: renesas_usb3: Add register of usb role switch")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MTK xHCI controller use some reserved bytes in endpoint context for
bandwidth scheduling, so need keep them in xhci_endpoint_copy();
The issue is introduced by:
commit f5249461b5 ("xhci: Clear the host side toggle manually when
endpoint is soft reset")
It resets endpoints and will drop bandwidth scheduling parameters used
by interrupt or isochronous endpoints on MTK xHCI controller.
Fixes: f5249461b5 ("xhci: Clear the host side toggle manually when
endpoint is soft reset")
Cc: stable@vger.kernel.org
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use IS_ERR() instead of IS_ERR_OR_NULL() because devm_of_phy_get_by_index()
never return NULL value;
But still need ignore the error of -ENODEV, for more information, please
refer to:
[0] https://lkml.org/lkml/2018/4/19/88
[1] https://patchwork.kernel.org/patch/10160181/
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vbus rise & fall interrupts are used to enable and disable
U3 function of device automatically, this cause some issues when
class driver is initialized as deactivated, and will skip over
software-controlled connect by pullup(), but UDC wants to keep
disconnect until usb_gadget_activate() is called which calls
pullup() if needed. So we disable vbus rise & fall interrupts
and just use pullup() to enable & disable U3 function, and reset
mtu3 state when disconnect instead when vbus fall.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to bitmap_zalloc() to show clearly what we are allocating.
Besides that it returns pointer of bitmap type instead of opaque void *.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
simple_strtoul is obsolete, and use kstrtoint instead
Signed-off-by: Ding Xiang <dingxiang@cmss.chinamobile.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A common flaw in the kernel is integer overflow during memory allocation
size calculations. In an effort to reduce the frequency of these bugs,
kmalloc_array was implemented, which allocates memory for an array,
while at the same time detects integer overflow.
This patch replaces cases of:
kmalloc(a * b, gfp)
with:
kmalloc_array(a, b, gfp)
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paul pointed out that the 50-ms sleep during OHCI initialization takes
up a large fraction of a system's boot time. Things get worse when
there are two OHCI controllers present, each requiring 50 ms.
However, there really is no need to send a 50-ms reset signal out all
the root-hub ports during initialization. The ports themselves will
be disabled, and the only way to enable a port is to reset it.
Therefore all attached USB devices will receive a proper reset in any
case. The controller reset does not need to be long enough to reset
those other devices, so the 50-ms delay isn't necessary.
Without the delay, there is no remaining incentive for skipping the
reset when the controller is already in the RESET state. This patch
removes the test, issuing the command unconditionally, and removes the
following delay.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Suggested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When used in a system with software-controlled silicon clocks,
the FOTG210 needs to grab, prepare and enable the clock.
This is needed on for example the Cortina Gemini, where the
platform will by default gate off the clock unless the
peripheral (in this case the USB driver) grabs and enables
the clock.
If there is no clock available on the platform, we live
without it. Make sure to percolate probe deferrals.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variables snk_pdo and toggling_mode_name are defined but are not used and
hence can be removed.
Cleans up clang warnings:
warning: 'snk_pdo' defined but not used [-Wunused-const-variable=]
warning: 'toggling_mode_name' defined but not used [-Wunused-const-variable=]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because USB_STORAGE build symbol strictly depends on SCSI build
symbol, there is no need to specify it again.
In addition USB_STORAGE_ENE_UB6250 entry description repeats a note
about SCSI dependency from the parent USB_STORAGE entry description,
hence the change removes this duplication.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of explicit setting of USB_STORAGE dependency for every
underlying build entries, exploit if USB_STORAGE / endif block.
The change is a trivial non-functional cleanup, it shortens
the Kconfig file and it is expected to reduce zconf parser
workload a little.
Dependencies of USB_UAS build option are left aside deliberately.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removing NULL check for pool since dma_pool_destroy is safe
Signed-off-by: Salil Kapur <salilkapur93@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The core disabled interrupts before invocation the ->complete handler
because the handler might have expected that interrupts are disabled.
All handlers were audited and use proper locking now. With it, the core
code no longer needs to disable interrupts before invoking the
->complete handler.
Remove local_irq_save() statement before invoking the ->complete
handler.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NET2280 got a fix to an old patch attempting to fix locking for gadget
framework callbacks.
DWC2 fixed a bug where driver was attempting to access registers before
clocks were enabled.
DWC3 got a fix for ULPI clock configuration on Baytrail devices.
FOTG210 plugged a memory leak and Renesas USB3 fixed ep0 maxpacket size.
-----BEGIN PGP SIGNATURE-----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=bEhk
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.19-rc2
NET2280 got a fix to an old patch attempting to fix locking for gadget
framework callbacks.
DWC2 fixed a bug where driver was attempting to access registers before
clocks were enabled.
DWC3 got a fix for ULPI clock configuration on Baytrail devices.
FOTG210 plugged a memory leak and Renesas USB3 fixed ep0 maxpacket size.
Here are two fixes for array-underflow bugs in completion handlers due
to insufficient sanity checks.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=XYLd
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.19-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.19-rc3
Here are two fixes for array-underflow bugs in completion handlers due
to insufficient sanity checks.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
wdm_in_callback() is a completion handler function for the USB driver.
So it should not sleep. But it calls service_outstanding_interrupt(),
which calls usb_submit_urb() with GFP_KERNEL.
To fix this bug, GFP_KERNEL is replaced with GFP_ATOMIC.
This bug is found by my static analysis tool DSAC.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
async_complete() in uss720.c is a completion handler function for the
USB driver. So it should not sleep, but it is can sleep according to the
function call paths (from bottom to top) in Linux-4.16.
[FUNC] set_1284_register(GFP_KERNEL)
drivers/usb/misc/uss720.c, 372:
set_1284_register in parport_uss720_frob_control
drivers/parport/ieee1284.c, 560:
[FUNC_PTR]parport_uss720_frob_control in parport_ieee1284_ack_data_avail
drivers/parport/ieee1284.c, 577:
parport_ieee1284_ack_data_avail in parport_ieee1284_interrupt
./include/linux/parport.h, 474:
parport_ieee1284_interrupt in parport_generic_irq
drivers/usb/misc/uss720.c, 116:
parport_generic_irq in async_complete
[FUNC] get_1284_register(GFP_KERNEL)
drivers/usb/misc/uss720.c, 382:
get_1284_register in parport_uss720_read_status
drivers/parport/ieee1284.c, 555:
[FUNC_PTR]parport_uss720_read_status in parport_ieee1284_ack_data_avail
drivers/parport/ieee1284.c, 577:
parport_ieee1284_ack_data_avail in parport_ieee1284_interrupt
./include/linux/parport.h, 474:
parport_ieee1284_interrupt in parport_generic_irq
drivers/usb/misc/uss720.c, 116:
parport_generic_irq in async_complete
Note that [FUNC_PTR] means a function pointer call is used.
To fix these bugs, GFP_KERNEL is replaced with GFP_ATOMIC.
These bugs are found by my static analysis tool DSAC.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i_usX2Y_subs_startup in usbusx2yaudio.c is a completion handler function
for the USB driver. So it should not sleep, but it is can sleep
according to the function call paths (from bottom to top) in Linux-4.16.
[FUNC] msleep
drivers/usb/host/u132-hcd.c, 2558:
msleep in u132_get_frame
drivers/usb/core/hcd.c, 2231:
[FUNC_PTR]u132_get_frame in usb_hcd_get_frame_number
drivers/usb/core/usb.c, 822:
usb_hcd_get_frame_number in usb_get_current_frame_number
sound/usb/usx2y/usbusx2yaudio.c, 303:
usb_get_current_frame_number in i_usX2Y_urb_complete
sound/usb/usx2y/usbusx2yaudio.c, 366:
i_usX2Y_urb_complete in i_usX2Y_subs_startup
Note that [FUNC_PTR] means a function pointer call is used.
To fix this bug, msleep() is replaced with mdelay().
This bug is found by my static analysis tool DSAC.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The steps taken by usb core to set a new interface is very different from
what is done on the xHC host side.
xHC hardware will do everything in one go. One command is used to set up
new endpoints, free old endpoints, check bandwidth, and run the new
endpoints.
All this is done by xHC when usb core asks the hcd to check for
available bandwidth. At this point usb core has not yet flushed the old
endpoints, which will cause use-after-free issues in xhci driver as
queued URBs are cancelled on a re-allocated endpoint.
To resolve this add a call to usb_disable_interface() which will flush
the endpoints before calling usb_hcd_alloc_bandwidth()
Additional checks in xhci driver will also be implemented to gracefully
handle stale URB cancel on freed and re-allocated endpoints
Cc: <stable@vger.kernel.org>
Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix kernel-doc warning for missing function parameter 'mode' description:
../drivers/usb/typec/bus.c:268: warning: Function parameter or member 'mode' not described in 'typec_match_altmode'
Also fix typos for same function documentation.
Fixes: 8a37d87d72 ("usb: typec: Bus type for alternate modes")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_hc_died() should only be called once, and with the primary HCD
as parameter. It will mark both primary and secondary hcd's dead.
Remove the extra call to usb_cd_died with the shared hcd as parameter.
Fixes: ff9d78b36f ("USB: Set usb_hcd->state and flags for shared roothubs")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If dual role mode is enabled, when switch u3port0 to device mode,
it will affect port id calculation of host(xHCI), specially when
host supports multi U2 ports or U3 ports, so need enable its dual
role mode, and fix it here.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hope that UAS devices would be less broken than old style storage
devices has turned out to be unfounded. Make UAS support more of the
quirk flags of the old driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device does not correctly handle the LPM operations.
Also, the device cannot handle ATA pass-through commands
and locks up when attempted while running in super speed.
This patch adds the equivalent quirk logic as found in uas.
Signed-off-by: Tim Anderson <tsa@biglakesoftware.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
snprintf() always returns the full length of the string it could have
printed, even if it was truncated because the buffer was too small.
So in case the counter value is truncated, we will over-read from
in_buffer and over-write to the caller's buffer.
I don't think it's actually possible for this to happen, but in case
truncation occurs, WARN and return -EIO.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the written data starts with a digit, yurex_write() tries to parse
it as an integer using simple_strtoull(). This requires a null-
terminator, and currently there's no guarantee that there is one.
(The sample program at
https://github.com/NeoCat/YUREX-driver-for-Linux/blob/master/sample/yurex_clock.pl
writes an integer without a null terminator. It seems like it must
have worked by chance!)
Always add a null byte after the written data. Enlarge the buffer
to allow for this.
Cc: stable@vger.kernel.org
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In xhci_plat_probe() both sysdev and pdev->dev are being used
for finding quirks. There are some drivers(like dwc3 host.c)
which adds quirks(like usb3-lpm-capable) into pdev and the logic
present in xhci_plat_probe() checks for quirks in either sysdev
or pdev for finding the quirks. Because of this logic, some of
the quirks are getting missed(usb3-lpm-capable quirk added by dwc3
host.c driver is getting missed).This patch fixes this by iterating
over all the available parents for finding the quirks. In this way
all the quirks which are present in child or parent are correctly
updated.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure the cancelled URB is on the current endpoint ring.
If the endpoint ring has been reallocated since the URB was enqueued
then the URB may contain TD and TRB pointers to a already freed ring.
In this the case return the URB without touching any of the freed ring
structure data.
Don't try to stop the ring. It would be useless.
This can occur if endpoint is not flushed before it is dropped and
re-added, which is the case in usb_set_interface() as xhci does
things in an odd order.
Cc: <stable@vger.kernel.org>
Tested-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
WORLDE Controller KS49 or Prodipe MIDI 49C USB controller
cause a -EPROTO error, a communication restart and loop again.
This issue has already been fixed for KS25.
https://lore.kernel.org/patchwork/patch/753077/
I just add device 201 for KS49 in quirks.c to get it works.
Signed-off-by: Laurent Roux <xpros64@hotmail.fr>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some SoC/IP as STM32F469, the snpsid can only be read after clock is
enabled, otherwise it will read as 0, and the dwc2_check_core_endianness
will assume the core and AHB have opposite endianness, leading to the
following error:
[ 1.976339] dwc2 50000000.usb: 50000000.usb supply vusb_d not found, using dummy regulator
[ 1.986124] dwc2 50000000.usb: Linked as a consumer to regulator.0
[ 1.992711] dwc2 50000000.usb: 50000000.usb supply vusb_a not found, using dummy regulator
[ 2.003672] dwc2 50000000.usb: dwc2_core_reset: HANG! AHB Idle timeout GRSTCTL GRSTCTL_AHBIDLE
[ 2.015176] dwc2: probe of 50000000.usb failed with error -16
The proposed patch changes the location where dwc2_check_core_endianness
is called, allowing the clock peripheral to be enabled first.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Bruno Meirelles Herrera <bmh@certi.org.br>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This implements the V4L2 part of the request support. The main
change is that vb2_qbuf and vb2_prepare_buf now have a new
media_device pointer. This required changes to several drivers
that did not use the vb2_ioctl_qbuf/prepare_buf helper functions.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In case of error, the function pcim_iomap() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: 7740d04d90 ("usb: dwc3: pci: Enable ULPI Refclk on platforms where the firmware does not")
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes an issue that maxpacket size of ep0 is incorrect
for SuperSpeed. Otherwise, CDC NCM class with SuperSpeed doesn't
work correctly on this driver because its control read data size
is more than 64 bytes.
Reported-by: Junki Kato <junki.kato.xk@renesas.com>
Fixes: 746bfe63bb ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Junki Kato <junki.kato.xk@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There is no deallocation of fotg210->ep[i] elements, allocated at
fotg210_udc_probe.
The patch adds deallocation of fotg210->ep array elements and simplifies
error path of fotg210_udc_probe().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Commit f16443a034 ("USB: gadgetfs, dummy-hcd, net2280: fix locking
for callbacks") was based on a serious misunderstanding. It
introduced regressions into both the dummy-hcd and net2280 drivers.
The problem in dummy-hcd was fixed by commit 7dbd8f4cab ("USB:
dummy-hcd: Fix erroneous synchronization change"), but the problem in
net2280 remains. Namely: the ->disconnect(), ->suspend(), ->resume(),
and ->reset() callbacks must be invoked without the private lock held;
otherwise a deadlock will occur when the callback routine tries to
interact with the UDC driver.
This patch largely is a reversion of the relevant parts of
f16443a034. It also drops the private lock around the calls to
->suspend() and ->resume() (something the earlier patch forgot to do).
This is safe from races with device interrupts because it occurs
within the interrupt handler.
Finally, the patch changes where the ->disconnect() callback is
invoked when net2280_pullup() turns the pullup off. Rather than
making the callback from within stop_activity() at a time when dropping
the private lock could be unsafe, the callback is moved to a point
after the lock has already been dropped.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: f16443a034 ("USB: gadgetfs, dummy-hcd, net2280: fix locking for callbacks")
Reported-by: D. Ziesche <dziesche@zes.com>
Tested-by: D. Ziesche <dziesche@zes.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
An incorrect #ifdef caused a pair of harmless warnings when CONFIG_PM_SLEEP
is disabled:
drivers/usb/dwc3/dwc3-of-simple.c:223:12: error: 'dwc3_of_simple_resume' defined but not used [-Werror=unused-function]
static int dwc3_of_simple_resume(struct device *dev)
^~~~~~~~~~~~~~~~~~~~~
drivers/usb/dwc3/dwc3-of-simple.c:213:12: error: 'dwc3_of_simple_suspend' defined but not used [-Werror=unused-function]
static int dwc3_of_simple_suspend(struct device *dev)
Since the #ifdef method is generally hard to get right, use
a simpler __maybe_unused annotation here to let the compiler
drop the unused functions silently. This also improves
compile-time coverage.
Fixes: 76251db865 ("usb: dwc3: of-simple: reset host controller at suspend/resume")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Similarly to a recently reported bug in io_ti, a malicious USB device
could set port_number to a negative value and we would underflow the
port array in the interrupt completion handler.
As these devices only have one or two ports, fix this by making sure we
only consider the seventh bit when determining the port number (and
ignore bits 0xb0 which are typically set to 0x30).
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
As reported by Dan Carpenter, a malicious USB device could set
port_number to a negative value and we would underflow the port array in
the interrupt completion handler.
As these devices only have one or two ports, fix this by making sure we
only consider the seventh bit when determining the port number (and
ignore bits 0xb0 which are typically set to 0x30).
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Some of the larger changes this merge window:
- Removal of drivers for Exynos5440, a Samsung SoC that never saw
widespread use.
- Uniphier support for USB3 and SPI reset handling
- Syste control and SRAM drivers and bindings for Allwinner platforms
- Qualcomm AOSS (Always-on subsystem) reset controller drivers
- Raspberry Pi hwmon driver for voltage
- Mediatek pwrap (pmic) support for MT6797 SoC
-----BEGIN PGP SIGNATURE-----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=ZjwY
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Some of the larger changes this merge window:
- Removal of drivers for Exynos5440, a Samsung SoC that never saw
widespread use.
- Uniphier support for USB3 and SPI reset handling
- Syste control and SRAM drivers and bindings for Allwinner platforms
- Qualcomm AOSS (Always-on subsystem) reset controller drivers
- Raspberry Pi hwmon driver for voltage
- Mediatek pwrap (pmic) support for MT6797 SoC"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (52 commits)
drivers/firmware: psci_checker: stash and use topology_core_cpumask for hotplug tests
soc: fsl: cleanup Kconfig menu
soc: fsl: dpio: Convert DPIO documentation to .rst
staging: fsl-mc: Remove remaining files
staging: fsl-mc: Move DPIO from staging to drivers/soc/fsl
staging: fsl-dpaa2: eth: move generic FD defines to DPIO
soc: fsl: qe: gpio: Add qe_gpio_set_multiple
usb: host: exynos: Remove support for Exynos5440
clk: samsung: Remove support for Exynos5440
soc: sunxi: Add the A13, A23 and H3 system control compatibles
reset: uniphier: add reset control support for SPI
cpufreq: exynos: Remove support for Exynos5440
ata: ahci-platform: Remove support for Exynos5440
soc: imx6qp: Use GENPD_FLAG_ALWAYS_ON for PU errata
soc: mediatek: pwrap: add mt6351 driver for mt6797 SoCs
soc: mediatek: pwrap: add pwrap driver for mt6797 SoCs
soc: mediatek: pwrap: fix cipher init setting error
dt-bindings: pwrap: mediatek: add pwrap support for MT6797
reset: uniphier: add USB3 core reset control
dt-bindings: reset: uniphier: add USB3 core reset support
...
Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level
hardware bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of
the crazy out-of-tree drivers that have been floating around
for years, combined with some really hacky userspace
implementations. This is only for GNSS receivers, but you
have to start somewhere, and this is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and existing
drivers.
Full details of everything is in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3g7ew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfBgCeOG0RkSI92XVZe0hs/QYFW9kk8JYAnRBf3Qpm
cvW7a+McOoKz/MGmEKsi
=TNfn
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level hardware
bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of the
crazy out-of-tree drivers that have been floating around for years,
combined with some really hacky userspace implementations. This is
only for GNSS receivers, but you have to start somewhere, and this
is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and
existing drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
android: binder: Rate-limit debug and userspace triggered err msgs
fsi: sbefifo: Bump max command length
fsi: scom: Fix NULL dereference
misc: mic: SCIF Fix scif_get_new_port() error handling
misc: cxl: changed asterisk position
genwqe: card_base: Use true and false for boolean values
misc: eeprom: assignment outside the if statement
uio: potential double frees if __uio_register_device() fails
eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency
misc: ti-st: Fix memory leak in the error path of probe()
android: binder: Show extra_buffers_size in trace
firmware: vpd: Fix section enabled flag on vpd_section_destroy
platform: goldfish: Retire pdev_bus
goldfish: Use dedicated macros instead of manual bit shifting
goldfish: Add missing includes to goldfish.h
mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux
dt-bindings: mux: add adi,adgs1408
Drivers: hv: vmbus: Cleanup synic memory free path
Drivers: hv: vmbus: Remove use of slow_virt_to_phys()
Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
...
Here is the big USB and phy driver patch set for 4.19-rc1.
Nothing huge but there was a lot of work that happened this development
cycle:
- lots of type-c work, with drivers graduating out of staging,
and displayport support being added.
- new PHY drivers
- the normal collection of gadget driver updates and fixes
- code churn to work on the urb handling path, using irqsave()
everywhere in anticipation of making this codepath a lot
simpler in the future.
- usbserial driver fixes and reworks
- other misc changes
Full details are in the shortlog.
All of these have been in linux-next with no reported issues for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3hBPA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yloNwCggMZi9m8Krjq7d7aLw5oJJex/nIAAn0jeADOT
NpoCgrtGHjwrATxN5/Ke
=jXa3
-----END PGP SIGNATURE-----
Merge tag 'usb-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big USB and phy driver patch set for 4.19-rc1.
Nothing huge but there was a lot of work that happened this
development cycle:
- lots of type-c work, with drivers graduating out of staging, and
displayport support being added.
- new PHY drivers
- the normal collection of gadget driver updates and fixes
- code churn to work on the urb handling path, using irqsave()
everywhere in anticipation of making this codepath a lot simpler in
the future.
- usbserial driver fixes and reworks
- other misc changes
All of these have been in linux-next with no reported issues for a
while"
* tag 'usb-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (159 commits)
USB: serial: pl2303: add a new device id for ATEN
usb: renesas_usbhs: Kconfig: convert to SPDX identifiers
usb: dwc3: gadget: Check MaxPacketSize from descriptor
usb: dwc2: Turn on uframe_sched on "stm32f4x9_fsotg" platforms
usb: dwc2: Turn on uframe_sched on "amlogic" platforms
usb: dwc2: Turn on uframe_sched on "his" platforms
usb: dwc2: Turn on uframe_sched on "bcm" platforms
usb: dwc2: gadget: ISOC's starting flow improvement
usb: dwc2: Make dwc2_readl/writel functions endianness-agnostic.
usb: dwc3: core: Enable AutoRetry feature in the controller
usb: dwc3: Set default mode for dwc_usb31
usb: gadget: udc: renesas_usb3: Add register of usb role switch
usb: dwc2: replace ioread32/iowrite32_rep with dwc2_readl/writel_rep
usb: dwc2: Modify dwc2_readl/writel functions prototype
usb: dwc3: pci: Intel Merrifield can be host
usb: dwc3: pci: Supply device properties via driver data
arm64: dts: dwc3: description of incr burst type
usb: dwc3: Enable undefined length INCR burst type
usb: dwc3: add global soc bus configuration reg0
usb: dwc3: Describe 'wakeup_work' field of struct dwc3_pci
...
Notable changes:
- A fix for a bug in our page table fragment allocator, where a page table page
could be freed and reallocated for something else while still in use, leading
to memory corruption etc. The fix reuses pt_mm in struct page (x86 only) for
a powerpc only refcount.
- Fixes to our pkey support. Several are user-visible changes, but bring us in
to line with x86 behaviour and/or fix outright bugs. Thanks to Florian Weimer
for reporting many of these.
- A series to improve the hvc driver & related OPAL console code, which have
been seen to cause hardlockups at times. The hvc driver changes in particular
have been in linux-next for ~month.
- Increase our MAX_PHYSMEM_BITS to 128TB when SPARSEMEM_VMEMMAP=y.
- Remove Power8 DD1 and Power9 DD1 support, neither chip should be in use
anywhere other than as a paper weight.
- An optimised memcmp implementation using Power7-or-later VMX instructions
- Support for barrier_nospec on some NXP CPUs.
- Support for flushing the count cache on context switch on some IBM CPUs
(controlled by firmware), as a Spectre v2 mitigation.
- A series to enhance the information we print on unhandled signals to bring it
into line with other arches, including showing the offending VMA and dumping
the instructions around the fault.
Thanks to:
Aaro Koskinen, Akshay Adiga, Alastair D'Silva, Alexey Kardashevskiy, Alexey
Spirkov, Alistair Popple, Andrew Donnellan, Aneesh Kumar K.V, Anju T Sudhakar,
Arnd Bergmann, Bartosz Golaszewski, Benjamin Herrenschmidt, Bharat Bhushan,
Bjoern Noetel, Boqun Feng, Breno Leitao, Bryant G. Ly, Camelia Groza,
Christophe Leroy, Christoph Hellwig, Cyril Bur, Dan Carpenter, Daniel Klamt,
Darren Stevens, Dave Young, David Gibson, Diana Craciun, Finn Thain, Florian
Weimer, Frederic Barrat, Gautham R. Shenoy, Geert Uytterhoeven, Geoff Levand,
Guenter Roeck, Gustavo Romero, Haren Myneni, Hari Bathini, Joel Stanley,
Jonathan Neuschäfer, Kees Cook, Madhavan Srinivasan, Mahesh Salgaonkar, Markus
Elfring, Mathieu Malaterre, Mauro S. M. Rodrigues, Michael Hanselmann, Michael
Neuling, Michael Schmitz, Mukesh Ojha, Murilo Opsfelder Araujo, Nicholas
Piggin, Parth Y Shah, Paul Mackerras, Paul Menzel, Ram Pai, Randy Dunlap,
Rashmica Gupta, Reza Arbab, Rodrigo R. Galvao, Russell Currey, Sam Bobroff,
Scott Wood, Shilpasri G Bhat, Simon Guo, Souptick Joarder, Stan Johnson,
Thiago Jung Bauermann, Tyrel Datwyler, Vaibhav Jain, Vasant Hegde, Venkat Rao
B, zhong jiang.
-----BEGIN PGP SIGNATURE-----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=PzRz
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Notable changes:
- A fix for a bug in our page table fragment allocator, where a page
table page could be freed and reallocated for something else while
still in use, leading to memory corruption etc. The fix reuses
pt_mm in struct page (x86 only) for a powerpc only refcount.
- Fixes to our pkey support. Several are user-visible changes, but
bring us in to line with x86 behaviour and/or fix outright bugs.
Thanks to Florian Weimer for reporting many of these.
- A series to improve the hvc driver & related OPAL console code,
which have been seen to cause hardlockups at times. The hvc driver
changes in particular have been in linux-next for ~month.
- Increase our MAX_PHYSMEM_BITS to 128TB when SPARSEMEM_VMEMMAP=y.
- Remove Power8 DD1 and Power9 DD1 support, neither chip should be in
use anywhere other than as a paper weight.
- An optimised memcmp implementation using Power7-or-later VMX
instructions
- Support for barrier_nospec on some NXP CPUs.
- Support for flushing the count cache on context switch on some IBM
CPUs (controlled by firmware), as a Spectre v2 mitigation.
- A series to enhance the information we print on unhandled signals
to bring it into line with other arches, including showing the
offending VMA and dumping the instructions around the fault.
Thanks to: Aaro Koskinen, Akshay Adiga, Alastair D'Silva, Alexey
Kardashevskiy, Alexey Spirkov, Alistair Popple, Andrew Donnellan,
Aneesh Kumar K.V, Anju T Sudhakar, Arnd Bergmann, Bartosz Golaszewski,
Benjamin Herrenschmidt, Bharat Bhushan, Bjoern Noetel, Boqun Feng,
Breno Leitao, Bryant G. Ly, Camelia Groza, Christophe Leroy, Christoph
Hellwig, Cyril Bur, Dan Carpenter, Daniel Klamt, Darren Stevens, Dave
Young, David Gibson, Diana Craciun, Finn Thain, Florian Weimer,
Frederic Barrat, Gautham R. Shenoy, Geert Uytterhoeven, Geoff Levand,
Guenter Roeck, Gustavo Romero, Haren Myneni, Hari Bathini, Joel
Stanley, Jonathan Neuschäfer, Kees Cook, Madhavan Srinivasan, Mahesh
Salgaonkar, Markus Elfring, Mathieu Malaterre, Mauro S. M. Rodrigues,
Michael Hanselmann, Michael Neuling, Michael Schmitz, Mukesh Ojha,
Murilo Opsfelder Araujo, Nicholas Piggin, Parth Y Shah, Paul
Mackerras, Paul Menzel, Ram Pai, Randy Dunlap, Rashmica Gupta, Reza
Arbab, Rodrigo R. Galvao, Russell Currey, Sam Bobroff, Scott Wood,
Shilpasri G Bhat, Simon Guo, Souptick Joarder, Stan Johnson, Thiago
Jung Bauermann, Tyrel Datwyler, Vaibhav Jain, Vasant Hegde, Venkat
Rao, zhong jiang"
* tag 'powerpc-4.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (234 commits)
powerpc/mm/book3s/radix: Add mapping statistics
powerpc/uaccess: Enable get_user(u64, *p) on 32-bit
powerpc/mm/hash: Remove unnecessary do { } while(0) loop
powerpc/64s: move machine check SLB flushing to mm/slb.c
powerpc/powernv/idle: Fix build error
powerpc/mm/tlbflush: update the mmu_gather page size while iterating address range
powerpc/mm: remove warning about ‘type’ being set
powerpc/32: Include setup.h header file to fix warnings
powerpc: Move `path` variable inside DEBUG_PROM
powerpc/powermac: Make some functions static
powerpc/powermac: Remove variable x that's never read
cxl: remove a dead branch
powerpc/powermac: Add missing include of header pmac.h
powerpc/kexec: Use common error handling code in setup_new_fdt()
powerpc/xmon: Add address lookup for percpu symbols
powerpc/mm: remove huge_pte_offset_and_shift() prototype
powerpc/lib: Use patch_site to patch copy_32 functions once cache is enabled
powerpc/pseries: Fix endianness while restoring of r3 in MCE handler.
powerpc/fadump: merge adjacent memory ranges to reduce PT_LOAD segements
powerpc/fadump: handle crash memory ranges array index overflow
...
This is mostly updates to the usual drivers: mpt3sas, lpfc, qla2xxx,
hisi_sas, smartpqi, megaraid_sas, arcmsr. In addition, with the
continuing absence of Nic we have target updates for tcmu and target
core (all with reviews and acks). The biggest observable change is
going to be that we're (again) trying to switch to mulitqueue as the
default (a user can still override the setting on the kernel command
line). Other major core stuff is the removal of the remaining
Microchannel drivers, an update of the internal timers and some
reworks of completion and result handling.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCW3R3niYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishauRAP4yfBKK
dbxF81c/Bxi/Stk16FWkOOrjs4CizwmnMcpM5wD/UmM9o6ebDzaYpZgA8wIl7X/N
o/JckEZZpIp+5NySZNc=
=ggLB
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates to the usual drivers: mpt3sas, lpfc, qla2xxx,
hisi_sas, smartpqi, megaraid_sas, arcmsr.
In addition, with the continuing absence of Nic we have target updates
for tcmu and target core (all with reviews and acks).
The biggest observable change is going to be that we're (again) trying
to switch to mulitqueue as the default (a user can still override the
setting on the kernel command line).
Other major core stuff is the removal of the remaining Microchannel
drivers, an update of the internal timers and some reworks of
completion and result handling"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (203 commits)
scsi: core: use blk_mq_run_hw_queues in scsi_kick_queue
scsi: ufs: remove unnecessary query(DM) UPIU trace
scsi: qla2xxx: Fix issue reported by static checker for qla2x00_els_dcmd2_sp_done()
scsi: aacraid: Spelling fix in comment
scsi: mpt3sas: Fix calltrace observed while running IO & reset
scsi: aic94xx: fix an error code in aic94xx_init()
scsi: st: remove redundant pointer STbuffer
scsi: qla2xxx: Update driver version to 10.00.00.08-k
scsi: qla2xxx: Migrate NVME N2N handling into state machine
scsi: qla2xxx: Save frame payload size from ICB
scsi: qla2xxx: Fix stalled relogin
scsi: qla2xxx: Fix race between switch cmd completion and timeout
scsi: qla2xxx: Fix Management Server NPort handle reservation logic
scsi: qla2xxx: Flush mailbox commands on chip reset
scsi: qla2xxx: Fix unintended Logout
scsi: qla2xxx: Fix session state stuck in Get Port DB
scsi: qla2xxx: Fix redundant fc_rport registration
scsi: qla2xxx: Silent erroneous message
scsi: qla2xxx: Prevent sysfs access when chip is down
scsi: qla2xxx: Add longer window for chip reset
...
-----BEGIN PGP SIGNATURE-----
iJEEABYIADkWIQQUwxxKyE5l/npt8ARiEGxRG/Sl2wUCW3HajRscamFjZWsuYW5h
c3pld3NraUBnbWFpbC5jb20ACgkQYhBsURv0pdvxAwEA+qS5O9ByxlhT+BUC4ck6
nIy0ITOCXP8ySoo8VVhzjikBAPrb9lFYGvHqzKN4dYtnSILPmlTSf1t1flng2Zev
NfoE
=lNwq
-----END PGP SIGNATURE-----
Merge tag 'leds-for-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
"LED triggers improvements make the biggest part of this pull request.
The most striking ones, that allowed for nice cleanups in the triggers
are:
- centralized handling of creation and removal of trigger sysfs
attributes via attribute group
- addition of module_led_trigger() helper
The other things that need to be mentioned:
New features and improvements to existing LED class drivers:
- lt3593: add DT support, switch to gpiod interface
- lm3692x: support LED sync configuration, change OF calls to fwnode
calls
- apu: modify PC Engines apu/apu2 driver to support apu3
Change in the drivers/net/can/led.c:
- mark led trigger as broken since it's in the way for the further
cleanups. It implements a subset of the netdev trigger and an Ack
is needed from someone who can actually test and confirm that the
netdev trigger works for can devices"
* tag 'leds-for-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds: (32 commits)
leds: ns2: Change unsigned to unsigned int
usb: simplify usbport trigger
leds: gpio trigger: simplifications from core changes
leds: backlight trigger: simplifications from core changes
leds: activity trigger: simplifications from core changes
leds: default-on trigger: make use of module_led_trigger()
leds: heartbeat trigger: simplifications from core changes
leds: oneshot trigger: simplifications from core changes
leds: transient trigger: simplifications from core changes
leds: timer trigger: simplifications from core changes
leds: netdev trigger: simplifications from core changes
leds: triggers: new function led_set_trigger_data()
leds: triggers: define module_led_trigger helper
leds: triggers: handle .trigger_data and .activated() in the core
leds: triggers: add device attribute support
leds: triggers: let struct led_trigger::activate() return an error code
leds: triggers: make the MODULE_LICENSE string match the actual license
leds: lm3692x: Support LED sync configuration
dt: bindings: lm3692x: Update binding for LED sync control
leds: lm3692x: Change DT calls to fwnode calls
...
This converts drivers that were only calling transport_deregister_session
to use target_remove_session. The calling of
transport_deregister_session_configfs via target_remove_session for these
types of drivers is ok, because they were not exporting info from fields
like sess_acl_list, sess->se_tpg and sess->fabric_sess_ptr from configfs
accessible functions, so they will see no difference.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rename target_alloc_session to target_setup_session to avoid confusion with
the other transport session allocation function that only allocates the
session and because the target_alloc_session does so much more. It
allocates the session, sets up the nacl and registers the session.
The next patch will then add a remove function to match the setup in this
one, so it should make sense for all drivers, except iscsi, to just call
those 2 functions to setup and remove a session.
iscsi will continue to be the odd driver.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Chris Boot <bootc@bootc.net>
Cc: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Cc: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Cc: <qla2xxx-upstream@qlogic.com>
Cc: Johannes Thumshirn <jth@kernel.org>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Movie Song <MovieSong@aten-itlab.cn>
Cc: Johan Hovold <johan@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Not a big pull request with only 37 non-merge commits, most of which
are touching dwc2 (74% of the changes).
The most important changes are dwc2's support for uframe scheduling
and its endian-agnostic readl/writel wrappers.
From dwc3 side we have a special new glue layer for Synopsys HAPS
which will help Synopsys running FPGA validation using our upstream
driver. We also have the beginnings of dual-role support for Intel
Merrifield platform.
Apart from these, just a series of non-critical changes.
-----BEGIN PGP SIGNATURE-----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=HiNz
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v4.19
Not a big pull request with only 37 non-merge commits, most of which
are touching dwc2 (74% of the changes).
The most important changes are dwc2's support for uframe scheduling
and its endian-agnostic readl/writel wrappers.
From dwc3 side we have a special new glue layer for Synopsys HAPS
which will help Synopsys running FPGA validation using our upstream
driver. We also have the beginnings of dual-role support for Intel
Merrifield platform.
Apart from these, just a series of non-critical changes.
endpoint->maxpacket is not updated after setting the
usb_set_maxpacket_limit() on endpoint enable. The MaxPacketSize can be
different than the endpoint->maxpacket_limit.
DWC3 has been consistently using MaxPacketSize from the endpoint's
descriptor, so let's keep it consistent and use the MaxPacketSize from
the endpoint's descriptor instead.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There's no reason to have the uframe scheduler off on dwc2. Running
with uframe_sched = False is equivalent to saying "I don't want to run
the correct code, I want to run the old and incorrect code".
The uframe scheduler has been off on stm32f4x9_fsotg since commit
e35b135055 ("usb: dwc2: Add support for STM32F429/439/469 USB OTG
HS/FS in FS mode (internal PHY)"). That commit is pretty recent, so
it's unclear to me why the uframe scheduler was left off. Hopefully
it's because someone copied it from other parameters and didn't think
to try it?
Presumably if everyone is good w/ the uframe_sched turned back on we
can kill all the old and crufty non-uframe sched code.
Reviewed-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There's no reason to have the uframe scheduler off on dwc2. Running
with uframe_sched = False is equivalent to saying "I don't want to run
the correct code, I want to run the old and incorrect code".
The uframe scheduler has been off on Amlogic since commit f94310ac07
("usb: dwc2: add support for Meson8b and GXBB SoCs"). While this was
after most of the recent improvements, notably the commit 9f9f09b048
("usb: dwc2: host: Totally redo the microframe scheduler"), presumably
the parameters were copied from another platform and the uframe
scheduler wasn't tried.
Presumably if everyone is good w/ the uframe_sched turned back on we
can kill all the old and crufty non-uframe sched code.
Reviewed-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There's no reason to have the uframe scheduler off on dwc2. Running
with uframe_sched = False is equivalent to saying "I don't want to run
the correct code, I want to run the old and incorrect code".
The uframe scheduler has been off on HiSilicon since commit
37dd9d65cc ("usb: dwc2: add support of hi6220"). Since then there
have been many many improvements, notably the commit 9f9f09b048
("usb: dwc2: host: Totally redo the microframe scheduler")
Presumably if everyone is good w/ the uframe_sched turned back on we
can kill all the old and crufty non-uframe sched code.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Reviewed-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There's no reason to have the uframe scheduler off on dwc2. Running
with uframe_sched = False is equivalent to saying "I don't want to run
the correct code, I want to run the old and incorrect code".
The uframe scheduler has been off on Broadcom since commit
58b179dcf2 ("staging: dwc2: disable uframe_sched on the bcm2835").
Since then there have been many many improvements, notably the commit
9f9f09b048 ("usb: dwc2: host: Totally redo the microframe
scheduler")
Presumably if everyone is good w/ the uframe_sched turned back on we
can kill all the old and crufty non-uframe sched code.
Reviewed-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
To start ISOC transfers in handlers dwc2_gadget_handle_nak() and
dwc2_gadget_handle_out_token_ep_disabled() driver reads current frame
number, based on which, set target frame number to start first ISOC
transfer.
In case if system's high IRQ latency and multiple EP's asserted
interrupt in same frame, there are high probability that when reading
current frame number in EP's handlers, actual frame number can be
increased. As result for bInterval > 1, starting target frame
will be set wrongly and all ISOC packets will be dropped.
In patch "usb: dwc2: Change reading of current frame number flow"
reading of current frame number done ASAP in common interrupt handler.
This frame number stored in frame_number variable which used as
starting frame number for ISOC EP's in above mentioned handlers.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Declared dwc2_check_core_endianness() function for dynamicly check
core endianness.
Added needs_byte_swap flag to hsotg structure, and depending on
flag swap value inside dwc2_readl/writel functions.
Signed-off-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
By default when core sees any transaction error (CRC or overflow) it
replies with terminating retry ACK (Retry=1 and Nump == 0).
Enabling this Auto Retry feature in controller will make the core send
a non-terminanting ACK upon such transaction errors. That is, ACK TP
with Retry=1 and Nump != 0.
Doing so will give controller a chance to recover from transient error
conditions.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc_usb31 does not support OTG mode. If the controller supports DRD but
the dr_mode is not specified or set to OTG, then set the mode to
peripheral.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds role switch support for R-Car SoCs into the USB 3.0
peripheral driver. Some R-Car SoCs (e.g. R-Car H3) have USB 3.0
dual-role device controller which has the USB 3.0 xHCI host and
Renesas USB 3.0 peripheral.
Unfortunately, the mode change register (DRD_CON) contains
the USB 3.0 peripheral controller side only. So, this renesas_usb3
driver manages the DRD_CON now. However, in peripheral mode, the host
should stop. Also the host hardware needs to reinitialize its own
registers when the mode changes from peripheral to host mode.
Otherwise, the host cannot work correctly (e.g. detect a device
as high-speed).
To achieve this reinitialization by a driver, this driver also
registers a role switch driver to manage the DRD_CON and get
a device pointer of usb 3.0 host from "companion" property of OF.
Then, when the usb role is changed, renesas_usb3_role_switch_set()
will attach/release the xhci-plat driver to reinitialize the host
hardware.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc2_readl_rep/dwc2_writel_rep functions using readl/writel in a
loop.
Signed-off-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added hsotg argument to dwc2_readl/writel function prototype,
and also instead of address pass offset of register.
hsotg will contain flag field for endianness.
Also customized dwc2_set_bit and dwc2_clear_bit function for
dwc2_readl/writel functions.
Signed-off-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
On Intel Edison board the OTG function is enabled, thus,
USB can switch to the host mode.
Allow that by changing dr_mode property to "otg" for Intel Merrifield.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For now all PCI enumerated dwc3 devices require some properties
to be present. This allows us to unconditionally append them and supply
via driver_data.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Enable the undefined length INCR burst type and set INCRx.
Different platform may has the different burst size type.
In order to get best performance, we need to tune the burst
size to one special value, instead of the default value.
Signed-off-by: Changming Huang <jerry.huang@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Pengbo Mu <pengbo.mu@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add the macro definition for global soc bus configuration
register 0
Signed-off-by: Changming Huang <jerry.huang@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Pengbo Mu <pengbo.mu@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Describe 'wakeup_work' field of struct dwc3_pci to avoid a warning:
drivers/usb/dwc3/dwc3-pci.c:59: warning: Function parameter or member 'wakeup_work' not described in 'dwc3_pci'
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
-----BEGIN PGP SIGNATURE-----
iQEwBAABCAAaBQJbWo96ExxwZXRlci5jaGVuQG54cC5jb20ACgkQSFkpgVDWcbv9
BwgAnNcotaqyTwAe1/Zq/enT3i49yeQmKyj1+OC1LKBqyAKp5IcSzx/9o+FqYWhC
YB+Sdy51Qq/7MsRNE2OdQFkJ/FmL2k7acc+oF9eBeMQ/EqU7nZGjs8jQrHUQ/R/I
6QpFguXIPgiwtRUyAEWGM7LIGc8a76GFXBJZALISzQRvj5WK7efO1ZwqLd1ELcJm
BuGtZ85WDEinuXAXKyjAyuF9tOIh5Y67/9JQ1slzj4WDhdnpN2ULBu3tFIPUROvo
755pX+K5WiKpST4BeX77VaCKj2pAgANE0YWJDLfGYlkoWyR/Y1mA0SA2jcS+PLs7
iA8NlLYZ04m1xL480dpNPkOWbA==
=wGOB
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
One patch to enable USB Ethernet gadget at Tegra platforms
Commit ff3f0789b3 ("usb: dwc3: use BIT() macro where possible")
changed DWC3_DEPCFG_STREAM_EVENT_EN from bit 13 to bit 12.
Spotted this cleanup typo while looking at diffs between 4.9.35 and
4.14.16 for a separate issue.
Fixes: ff3f0789b3 ("usb: dwc3: use BIT() macro where possible")
Signed-off-by: Erich E. Hoover <ehoover@sweptlaser.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If we power off the SoC logic rail in S3, we can find that the Type-C
PHY can't initialize correctly after system resume. We need to toggle
the USB3-OTG reset before trying to initialize the PHY, or else it
times out.
phy phy-ff800000.phy.9: phy poweron failed --> -110
dwc3 fe900000.dwc3: failed to initialize core
dwc3: probe of fe900000.dwc3 failed with error -110
Note that the RK3399 TRM suggests that we should keep the whole usb3
controller in reset for the duration of the Type-C PHY initialization.
However, it's hard to assert the reset in the current framework of
reset. We're still skeptical about that, and we haven't yet found a
case where this seems to have mattered. This approach is much easier, it
simply holds the USB3-OTG reset while device is supended.
The dwc3 core is going to reinitialize the controller at suspend/resume
anyway (including a "soft reset"), so it should be safe to do this.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The kref used to be needed because sharing of fsg_common among multiple USB
function instances was handled by fsg. Now this is managed by configfs, we
don't need it anymore. So let's eliminate kref from this driver.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Jaejoong Kim <climbbb.kim@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
fsg_common_set_num_buffers() may fail due to ENOMEM. So add
error handling for fail case.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Jaejoong Kim <climbbb.kim@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Even though we only use them once, it is better to not put/release
the GPIOs immediately after use, so that others cannot claim them.
Use devm functions to get the phy GPIOs, so that they will be
automatically released when were unbound from the device and
remove the gpio_put calls.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
On some Bay Trail (BYT) systems the firmware does not enable the
ULPI Refclk.
This commit adds a helper which checks and if necessary enabled the Refclk
and calls this helper for BYT machines.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Bay Trail / BYT SoCs do not have a builtin device-mode phy, instead
they require an external ULPI phy for device-mode.
Only some BYT devices have an external phy, but even on those devices
device-mode is not working because the dwc3 does not see the phy.
The problem is that the ACPI fwnode for the dwc3 does not contain the
expected GPIO resources for the GPIOs connected to the chip-select and
reset pins of the phy.
I've found the workaround which some Android x86 kernels use for this:
https://github.com/BORETS24/Kernel-for-Asus-Zenfone-2/blob/master/arch/x86/platform/intel-mid/device_libs/pci/platform_usb_otg.c
Which boils down to hardcoding the GPIOs for these devices.
The good news it that all boards (*) use the same GPIOs.
This commit fixes the ULPI phy not woring by adding a gpiod_lookup_table
call which adds a hardcoded mapping for BYT devices. Note that the mapping
added by gpiod_add_lookup_table is a fallback mapping, so boards which
properly provide GPIO resources in the ACPI firmware-node resources
will not use this.
*) Except for the first revision of the evalulation-kit, which normal users
don't have
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This documentation patch specifies that certain USB gadget endpoint
operations may be called in interrupt context:
usb_ep_queue, usb_ep_dequeue, usb_ep_set_halt,
usb_ep_clear_halt, usb_ep_set_wedge, usb_ep_fifo_status,
and usb_ep_fifo_flush;
while others must be called in process context:
usb_ep_enable and usb_ep_disable.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This fixes the following checkpatch error:
ERROR: code indent should use tabs where possible
Here, spaces are replaced by a tab in 2 lines.
Signed-off-by: Parth Y Shah <sparth1292@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This driver is to be used for Synopsys PCIe-base HAPS platform. Move the
the HAPS support from dwc3-pci to this driver.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Commit 1b9ba000 ("Allow function drivers to pause control
transfers") states that USB_GADGET_DELAYED_STATUS is only
supported if data phase is 0 bytes.
It seems that when the length is not 0 bytes, there is no
need to explicitly delay the data stage since the transfer
is not completed until the user responds. However, when the
length is 0, there is no data stage and the transfer is
finished once setup() returns, hence there is a need to
explicitly delay completion.
This manifests as the following bugs:
Prior to 946ef68ad4 ('Let setup() return
USB_GADGET_DELAYED_STATUS'), when setup is 0 bytes, ffs
would require user to queue a 0 byte request in order to
clear setup state. However, that 0 byte request was actually
not needed and would hang and cause errors in other setup
requests.
After the above commit, 0 byte setups work since the gadget
now accepts empty queues to ep0 to clear the delay, but all
other setups hang.
Fixes: 946ef68ad4 ("Let setup() return USB_GADGET_DELAYED_STATUS")
Signed-off-by: Jerry Zhang <zhangjerry@google.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When utilising multiple instantiations of a UVC gadget on a composite
device, there is no clear method to link a particular configuration to
its respective video node.
Provide a means for identifying the correct video node by exposing the
name of the function configuration through sysfs.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The to_f_uvc_opts() function is forward-declared without needing to, as
its definition can simply be moved up in the file. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Moved dwc2_readl/writel functions after hsotg declaration for
adding hsotg structure to dwc2_readl/writel function prototypes.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Trivial fix to spelling mistake in usbg_us_strings array
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The trace module parameter controls output of debugging messages in the
UVC function driver. Move it from the webcam module to the UVC function
module where it belongs. This allows ConfigFS-based UVC gadgets to
control tracing.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In order to speed up compilation, only include the headers that are
strictly required within other headers. To that end, use forward
structure declaration and move #include statements to .c file as
appropriate.
While at it, sort headers alphabetically, and remove unneeded __KERNEL__
guards.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The UVC gadget userspace API (V4L2 events and custom ioctls) is defined
in a header internal to the kernel. Move it to a new public header to
make it accessible to userspace.
The UVC_INTF_CONTROL and UVC_INTF_STREAMING macros are not used, so
remove them in the process.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The Exynos5440 (quad-core A15 with GMAC, PCIe, SATA) was targeting
server platforms but it did not make it to the market really. There are
no development boards with it and probably there are no real products
neither. The development for Exynos5440 ended in 2013 and since then
the platform is in maintenance mode.
Removing Exynos5440 makes our life slightly easier: less maintenance,
smaller code, reduced number of quirks, no need to preserve DTB
backward-compatibility.
The Device Tree sources and some of the drivers for Exynos5440 were
already removed. This removes remaining drivers.
-----BEGIN PGP SIGNATURE-----
iQItBAABCAAXBQJbWKG7EBxrcnprQGtlcm5lbC5vcmcACgkQwTdm5oaLg9fNiA//
U/dI+ihiIXHOxtrVRZXNGsmI5545pUqLI5uTE9utvD2j10Ef+T45wOzcJEtVN5ro
+Mnqt32+LC0UfAo721Vfziu91t9HCYdeq6gFfgKS3mm5GPqqmsD7havl/UpT4jvL
JZZLTPoInT2zJ0oZanzIRoM5I7KCOrUikkoVYEq9Z2/DupZ/S1GJLYXq1kY00eXS
xrtNxTyhi6Hmg80h1u93jUfilWPuYvXAuTfK+nyHNXLDkVRAprEXEc0HCdKp0gKT
hCEVd/k2+FsREQSCq5+dCTvYwa/FATqvwU/pKZmhSuN4GOM6b/0kFFvTt0sUswY3
ZFGnEhnXQ9JGHf3/1cXdRn3e/1/5vOyjchKzCdF5Pyo40HIvI1qSK4mhCSO355PO
sIgI2OEEBCqVuu4HUeWDu13M7Q4haSHRCtqVyulT2LsNGRrm3Ko13lCz+knanMqH
4Cs7dLSz4ZqCSC4XYs8lnUvOFu2e/71vYs39QMi9yGro9Wn5T7H4qPNLVUuMER3K
Hwrj5CpGKqBnMt3qFAfsxB0CnHU+yIRb55qp9nTZSUzZ9B++qnDhoDd1ikYtc/yh
EHAnszKGPox2JbBzJRRQtpUq+qegnFaAkjssZf2eY89KKkjw/sHtssMA60dpV1tY
txpP7KiTiM3Cq0/Jdqi5D2kiiiFtpABo1Jb3CLzxlTk=
=3x4x
-----END PGP SIGNATURE-----
Merge tag 'samsung-drivers-exynos5440-4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/drivers
Exynos5440 drivers removal
The Exynos5440 (quad-core A15 with GMAC, PCIe, SATA) was targeting
server platforms but it did not make it to the market really. There are
no development boards with it and probably there are no real products
neither. The development for Exynos5440 ended in 2013 and since then
the platform is in maintenance mode.
Removing Exynos5440 makes our life slightly easier: less maintenance,
smaller code, reduced number of quirks, no need to preserve DTB
backward-compatibility.
The Device Tree sources and some of the drivers for Exynos5440 were
already removed. This removes remaining drivers.
* tag 'samsung-drivers-exynos5440-4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
usb: host: exynos: Remove support for Exynos5440
clk: samsung: Remove support for Exynos5440
cpufreq: exynos: Remove support for Exynos5440
ata: ahci-platform: Remove support for Exynos5440
Signed-off-by: Olof Johansson <olof@lixom.net>
The Exynos5440 is not actively developed, there are no development
boards available and probably there are no real products with it.
Remove wide-tree support for Exynos5440.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
32 bit applications can only call ioctl functions on 64 bit systems
when the field .compat_ioctl is defined for file operations.
Tested-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on USB2.0 Spec Section 11.12.5,
"If a hub has per-port power switching and per-port current limiting,
an over-current on one port may still cause the power on another port
to fall below specific minimums. In this case, the affected port is
placed in the Power-Off state and C_PORT_OVER_CURRENT is set for the
port, but PORT_OVER_CURRENT is not set."
so let's check C_PORT_OVER_CURRENT too for over current condition.
Fixes: 08d1dec6f4 ("usb:hub set hub->change_bits when over-current happens")
Cc: <stable@vger.kernel.org>
Tested-by: Alessandro Antenucci <antenucci@korg.it>
Signed-off-by: Bin Liu <b-liu@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
add USBTMC_IOCTL_CONFIG_TERMCHAR to control TermChar handling
for next read(). Controls field 'TermChar' and Bit 1 of field
'bmTransferAttributes' of REQUEST_DEV_DEP_MSG_IN BULK-OUT header.
Allows enabling/disabling of terminating a read on reception of
term_char individually for each read request.
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Tested-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
add USBTMC_IOCTL_EOM_ENABLE to specify EOM bit for next write()
call. Sets Bit 0 of field 'bmTransferAttributes' of DEV_DEP_MSG_OUT
Bulk-OUT Header.
Allows fine grained control over end of message handling on a
per file descriptor basis.
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Tested-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
add USBTMC488_IOCTL_TRIGGER to send TRIGGER Bulk-OUT header
according to Subclass USB488 Specification
The usbtmc trigger command is equivalent to the IEEE 488 GET (Group
Execute Trigger) action. While the "*TRG" command can be sent as
data to perform the same operation, in some situations an instrument
will be busy and unable to process the data immediately in which
case the USBTMC488_IOCTL_TRIGGER can be used to trigger the
instrument with lower latency.
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Tested-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add ioctls USBTMC_IOCTL_GET_TIMEOUT / USBTMC_IOCTL_SET_TIMEOUT to
get/set I/O timeout for specific file handle.
Different operations on an instrument can take different lengths of
time thus it is important to be able to set the timeout slightly
longer than the expected duration of each operation to optimise the
responsiveness of the application. As the instrument may be shared by
multiple applications the timeout should be settable on a per file
descriptor basis.
Tested-by: Dave Penkler <dpenkler@gmail.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- use consistent error value ETIMEOUT instead of ETIME
Tested-by: Dave Penkler <dpenkler@gmail.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add 'struct usbtmc_file_data' for each file handle to cache last
srq_byte (=Status Byte with SRQ) received by usbtmc_interrupt(..)
usbtmc488_ioctl_read_stb returns cached srq_byte when available for
each file handle to avoid race conditions of concurrent applications.
SRQ now sets EPOLLPRI instead of EPOLLIN since EPOLLIN is now reserved
for asynchronous reads
Tested-by: Dave Penkler <dpenkler@gmail.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix build errors when built for PPC64:
These variables are only used on PPC32 so they don't need to be
initialized for PPC64.
../drivers/usb/phy/phy-fsl-usb.c: In function 'usb_otg_start':
../drivers/usb/phy/phy-fsl-usb.c:865:3: error: '_fsl_readl' undeclared (first use in this function); did you mean 'fsl_readl'?
_fsl_readl = _fsl_readl_be;
../drivers/usb/phy/phy-fsl-usb.c:865:16: error: '_fsl_readl_be' undeclared (first use in this function); did you mean 'fsl_readl'?
_fsl_readl = _fsl_readl_be;
../drivers/usb/phy/phy-fsl-usb.c:866:3: error: '_fsl_writel' undeclared (first use in this function); did you mean 'fsl_writel'?
_fsl_writel = _fsl_writel_be;
../drivers/usb/phy/phy-fsl-usb.c:866:17: error: '_fsl_writel_be' undeclared (first use in this function); did you mean 'fsl_writel'?
_fsl_writel = _fsl_writel_be;
../drivers/usb/phy/phy-fsl-usb.c:868:16: error: '_fsl_readl_le' undeclared (first use in this function); did you mean 'fsl_readl'?
_fsl_readl = _fsl_readl_le;
../drivers/usb/phy/phy-fsl-usb.c:869:17: error: '_fsl_writel_le' undeclared (first use in this function); did you mean 'fsl_writel'?
_fsl_writel = _fsl_writel_le;
and the sysfs "show" function return type should be ssize_t, not int:
../drivers/usb/phy/phy-fsl-usb.c:1042:49: error: initialization of 'ssize_t (*)(struct device *, struct device_attribute *, char *)' {aka 'long int (*)(struct device *, struct device_attribute *, char *)'} from incompatible pointer type 'int (*)(struct device *, struct device_attribute *, char *)' [-Werror=incompatible-pointer-types]
static DEVICE_ATTR(fsl_usb2_otg_state, S_IRUGO, show_fsl_usb2_otg_state, NULL);
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: linux-usb@vger.kernel.org
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the USB-serial updates for 4.19-rc1, including:
- gpio support for CP2102N devices
- improved line-speed handling for cp210x
- conversion to spin_lock_irqsave() in completion handlers
- dropped kl5kusb105 support from the kl5kusb105 driver (sic!)
Included are also various lower-priority fixes and clean ups.
All but the final commit have been in linux-next, and with no reported
issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=0ukW
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.19-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.19-rc1
Here are the USB-serial updates for 4.19-rc1, including:
- gpio support for CP2102N devices
- improved line-speed handling for cp210x
- conversion to spin_lock_irqsave() in completion handlers
- dropped kl5kusb105 support from the kl5kusb105 driver (sic!)
Included are also various lower-priority fixes and clean ups.
All but the final commit have been in linux-next, and with no reported
issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
This patch adds GPIO support for CP2102N devices.
It introduces new generic code to support emulating separate
input and outputs directions even though these devices
only know output modes (open-drain and pushpull). Existing
GPIO support for CP2105 has been migrated over to the new
code structure.
Only limitation is that for the QFN28 variant, only 4 out of
7 GPIOs are supported. This is because the config array
locations of the last 3 pins are not documented, and reverse
engineering revealed offsets that conflicted with other
documented functions. Hence we'll play it safe instead
until somebody clears this up further.
Signed-off-by: Karoly Pados <pados@pados.hu>
[ johan: fix style issues and a couple of minor bugs; use Karoly's
updated commit message ]
Acked-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Johan Hovold <johan@kernel.org>
If td_list is not empty the cfg_cmd will not be freed,
call xhci_free_command to free it.
Signed-off-by: Zheng Xiaowei <zhengxiaowei@ruijie.com.cn>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a bug in the sink PDO search code when trying to select
a PPS APDO. The current code actually sets the starting index for
searching to whatever value 'i' is, rather than choosing index 1
to avoid the first PDO (always 5V fixed). As a result, for sources
which support PPS but whose PPS APDO index does not match with the
supporting sink PPS APDO index for the platform, no valid PPS APDO
will be found so this feature will not be permitted.
Sadly in testing, both Source and Sink capabilities matched up and
this was missed. Code is now updated to correctly set the start
index to 1, and testing with additional PPS capable sources show
this to work as expected.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Fixes: 2eadc33f40 ("typec: tcpm: Add core support for sink side PPS")
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 1b9ba000 ("Allow function drivers to pause control
transfers") states that USB_GADGET_DELAYED_STATUS is only
supported if data phase is 0 bytes.
It seems that when the length is not 0 bytes, there is no
need to explicitly delay the data stage since the transfer
is not completed until the user responds. However, when the
length is 0, there is no data stage and the transfer is
finished once setup() returns, hence there is a need to
explicitly delay completion.
This manifests as the following bugs:
Prior to 946ef68ad4 ('Let setup() return
USB_GADGET_DELAYED_STATUS'), when setup is 0 bytes, ffs
would require user to queue a 0 byte request in order to
clear setup state. However, that 0 byte request was actually
not needed and would hang and cause errors in other setup
requests.
After the above commit, 0 byte setups work since the gadget
now accepts empty queues to ep0 to clear the delay, but all
other setups hang.
Fixes: 946ef68ad4 ("Let setup() return USB_GADGET_DELAYED_STATUS")
Signed-off-by: Jerry Zhang <zhangjerry@google.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the coherent_dma_mask for the PS3 ehci, ohci, and snd devices.
Silences WARN_ON_ONCE messages emitted by the dma_alloc_attrs() routine.
Reported-by: Fredrik Noring <noring@nocrew.org>
Signed-off-by: Geoff Levand <geoff@infradead.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
CP2104 and the ECI interface of CP2105 support further baud rates than
the ones specified in AN205 table 1, and we can use the same equations
as for CP2102N to determine and report back the actual baud rates used.
Note that this could eventually be generalised also to CP2108, which
uses a different base clock. There appears to be an error in the CP2108
equations which needs to be confirmed on actual hardware first however
(specifically, the subtraction of one from the divisor appears to be
incorrect as it introduces larger errors).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The CP2102N equations for determining the actual baud rate can be used
also for other device types, so let's factor it out.
Note that this removes the now unused cp210x_is_cp2102n() helper.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
CP2102N devices support a lot more baudrates than earlier chips by
SiLabs. These devices are not constrained anymore by the table in AN205,
and are able to generate almost any baudrate in the supported range
with only minimal errors. This has also been verified with a scope on
a physical device. This patch adds support for all baudrates supported
by the CP2102N.
Signed-off-by: Karoly Pados <pados@pados.hu>
[johan: rework on top of an205 and max-speed patches ]
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Newer cp210x devices support higher line speeds than the older ones
which supported a discrete set of speeds up to 921.6 kbaud.
To support these higher speeds, we have for some time mapped speeds
lower than 1 Mbaud to the speeds supported by older devices, while
allowing the device to pick the closest possible rate for higher speeds
(without trying to guess and report back what rate was actually chosen).
As this implementation can lead to undefined behaviour for older devices
which do not support the higher rates, let's use the later-added
device-type detection to determine the maximum supported speed.
This will also be useful when adding support for cp2102n which can
handle rates up to 3 Mbaud.
As per the data sheets the following maximum speeds are used
cp2101 921.6 kbaud
cp2102/3 1 Mbaud
cp2104/8 2 Mbaud
cp2105
- ECI port 2 Mbaud
- SCI port 921.6 kbaud
while keeping the maximum 2 Mbaud for unknown device types in order to
avoid any regressions.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Older cp210x devices only support a fixed set of line speeds to which a
requested speed is mapped. Reimplement this mapping using a table
instead of a long if-else construct.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The list [1] of commits doing endianness fixes in USB subsystem is long
due to below quote from USB spec Revision 2.0 from April 27, 2000:
------------
8.1 Byte/Bit Ordering
Multiple byte fields in standard descriptors, requests, and responses
are interpreted as and moved over the bus in little-endian order, i.e.
LSB to MSB.
------------
This commit belongs to the same family.
[1] Example of endianness fixes in USB subsystem:
commit 14e1d56cbe ("usb: gadget: f_uac2: endianness fixes.")
commit 42370b8211 ("usb: gadget: f_uac1: endianness fixes.")
commit 63afd5cc78 ("USB: chaoskey: fix Alea quirk on big-endian hosts")
commit 74098c4ac7 ("usb: gadget: acm: fix endianness in notifications")
commit cdd7928df0 ("ACM gadget: fix endianness in notifications")
commit 323ece54e0 ("cdc-wdm: fix endianness bug in debug statements")
commit e102609f10 ("usb: gadget: uvc: Fix endianness mismatches")
list goes on
Fixes: 132fcb4608 ("usb: gadget: Add Audio Class 2.0 Driver")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Make sure only to copy any actual data rather than the whole buffer,
when releasing the temporary buffer used for unaligned non-isochronous
transfers.
Taken directly from commit 0efd937e27 ("USB: ehci-tegra: fix inefficient
copy of unaligned buffers")
Tested with Lantiq xRX200 (MIPS) and RPi Model B Rev 2 (ARM)
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The commit 3bc04e28a0 ("usb: dwc2: host: Get aligned DMA in a more
supported way") introduced a common way to align DMA allocations.
The code in the commit aligns the struct dma_aligned_buffer but the
actual DMA address pointed by data[0] gets aligned to an offset from
the allocated boundary by the kmalloc_ptr and the old_xfer_buffer
pointers.
This is against the recommendation in Documentation/DMA-API.txt which
states:
Therefore, it is recommended that driver writers who don't take
special care to determine the cache line size at run time only map
virtual regions that begin and end on page boundaries (which are
guaranteed also to be cache line boundaries).
The effect of this is that architectures with non-coherent DMA caches
may run into memory corruption or kernel crashes with Unhandled
kernel unaligned accesses exceptions.
Fix the alignment by positioning the DMA area in front of the allocation
and use memory at the end of the area for storing the orginal
transfer_buffer pointer. This may have the added benefit of increased
performance as the DMA area is now fully aligned on all architectures.
Tested with Lantiq xRX200 (MIPS) and RPi Model B Rev 2 (ARM).
Fixes: 3bc04e28a0 ("usb: dwc2: host: Get aligned DMA in a more supported way")
Cc: <stable@vger.kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The Aspeed SoC has a memory ordering issue that (thankfully)
only affects the USB gadget device. A read back is necessary
after writing to memory and before letting the device DMA
from it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Variable maxpacket is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'maxpacket' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For unidirectional endpoints, the endpoint pointer will be NULL for the
unused direction. Check that the endpoint is active before
dereferencing this pointer.
Fixes: 1b4977c793 ("usb: dwc2: Update dwc2_handle_incomplete_isoc_in() function")
Fixes: 689efb2619 ("usb: dwc2: Update dwc2_handle_incomplete_isoc_out() function")
Fixes: d84845522d ("usb: dwc2: Update GINTSTS_GOUTNAKEFF interrupt handling")
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix build errors when built for PPC64:
These variables are only used on PPC32 so they don't need to be
initialized for PPC64.
../drivers/usb/phy/phy-fsl-usb.c: In function 'usb_otg_start':
../drivers/usb/phy/phy-fsl-usb.c:865:3: error: '_fsl_readl' undeclared (first use in this function); did you mean 'fsl_readl'?
_fsl_readl = _fsl_readl_be;
../drivers/usb/phy/phy-fsl-usb.c:865:16: error: '_fsl_readl_be' undeclared (first use in this function); did you mean 'fsl_readl'?
_fsl_readl = _fsl_readl_be;
../drivers/usb/phy/phy-fsl-usb.c:866:3: error: '_fsl_writel' undeclared (first use in this function); did you mean 'fsl_writel'?
_fsl_writel = _fsl_writel_be;
../drivers/usb/phy/phy-fsl-usb.c:866:17: error: '_fsl_writel_be' undeclared (first use in this function); did you mean 'fsl_writel'?
_fsl_writel = _fsl_writel_be;
../drivers/usb/phy/phy-fsl-usb.c:868:16: error: '_fsl_readl_le' undeclared (first use in this function); did you mean 'fsl_readl'?
_fsl_readl = _fsl_readl_le;
../drivers/usb/phy/phy-fsl-usb.c:869:17: error: '_fsl_writel_le' undeclared (first use in this function); did you mean 'fsl_writel'?
_fsl_writel = _fsl_writel_le;
and the sysfs "show" function return type should be ssize_t, not int:
../drivers/usb/phy/phy-fsl-usb.c:1042:49: error: initialization of 'ssize_t (*)(struct device *, struct device_attribute *, char *)' {aka 'long int (*)(struct device *, struct device_attribute *, char *)'} from incompatible pointer type 'int (*)(struct device *, struct device_attribute *, char *)' [-Werror=incompatible-pointer-types]
static DEVICE_ATTR(fsl_usb2_otg_state, S_IRUGO, show_fsl_usb2_otg_state, NULL);
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: linux-usb@vger.kernel.org
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When handling split transactions we will try to delay retry after
getting a NAK from the device. This works well for BULK transfers that
can be polled for essentially forever. Unfortunately, on slower systems
at boot time, when the kernel is busy enumerating all the devices (USB
or not), we issue a bunch of control requests (reading device
descriptors, etc). If we get a NAK for the IN part of the control
request and delay retry for too long (because the system is busy), we
may confuse the device when we finally get to reissue SSPLIT/CSPLIT IN
and the device will respond with STALL. As a result we end up with
failure to get device descriptor and will fail to enumerate the device:
[ 3.428801] usb 2-1.2.1: new full-speed USB device number 9 using dwc2
[ 3.508576] usb 2-1.2.1: device descriptor read/8, error -32
[ 3.699150] usb 2-1.2.1: device descriptor read/8, error -32
[ 3.891653] usb 2-1.2.1: new full-speed USB device number 10 using dwc2
[ 3.968859] usb 2-1.2.1: device descriptor read/8, error -32
...
Let's not delay retries of split CONTROL IN transfers, as this allows us
to reliably enumerate devices at boot time.
Fixes: 38d2b5fb75 ("usb: dwc2: host: Don't retry NAKed transactions right away")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Substream period size potentially can be changed in runtime, however
this is not accounted in the data copying routine, the change replaces
the cached value with an actual value from substream runtime.
As a side effect the change also removes a potential division by zero
in u_audio_iso_complete() function, if there is a race with
uac_pcm_hw_free(), which sets prm->period_size to 0.
Fixes: 132fcb4608 ("usb: gadget: Add Audio Class 2.0 Driver")
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There is no necessity to copy PCM stream ring buffer area and size
properties to UAC private data structure, these values can be got
from substream itself.
The change gives more control on substream and avoid stale caching.
Fixes: 132fcb4608 ("usb: gadget: Add Audio Class 2.0 Driver")
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In u_audio_iso_complete, the runtime hw_ptr is updated before the
data is actually copied over to/from the buffer/dma area. When
ALSA uses this hw_ptr, the data may not actually be available to
be used. This causes trash/stale audio to play/record. This
patch updates the hw_ptr after the data has been copied to avoid
this.
Fixes: 132fcb4608 ("usb: gadget: Add Audio Class 2.0 Driver")
Signed-off-by: Joshua Frkuska <joshua_frkuska@mentor.com>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix below smatch (v0.5.0-4443-g69e9094e11c1) warnings:
drivers/usb/gadget/function/u_audio.c:607 g_audio_setup() warn: strcpy() 'pcm_name' of unknown size might be too large for 'pcm->name'
drivers/usb/gadget/function/u_audio.c:614 g_audio_setup() warn: strcpy() 'card_name' of unknown size might be too large for 'card->driver'
drivers/usb/gadget/function/u_audio.c:615 g_audio_setup() warn: strcpy() 'card_name' of unknown size might be too large for 'card->shortname'
Below commits performed a similar 's/strcpy/strlcpy/' rework:
* v2.6.31 commit 8372d4980f ("ALSA: ctxfi - Fix PCM device naming")
* v4.14 commit 003d3e70db ("ALSA: ad1848: fix format string overflow warning")
* v4.14 commit 6d8b04de87 ("ALSA: cs423x: fix format string overflow warning")
Fixes: eb9fecb9e6 ("usb: gadget: f_uac2: split out audio core")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The driver may sleep in an interrupt handler.
The function call path (from bottom to top) in Linux-4.16.7 is:
[FUNC] r8a66597_queue(GFP_KERNEL)
drivers/usb/gadget/udc/r8a66597-udc.c, 1193:
r8a66597_queue in get_status
drivers/usb/gadget/udc/r8a66597-udc.c, 1301:
get_status in setup_packet
drivers/usb/gadget/udc/r8a66597-udc.c, 1381:
setup_packet in irq_control_stage
drivers/usb/gadget/udc/r8a66597-udc.c, 1508:
irq_control_stage in r8a66597_irq (interrupt handler)
To fix this bug, GFP_KERNEL is replaced with GFP_ATOMIC.
This bug is found by my static analysis tool (DSAC-2) and checked by
my code review.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The driver may sleep with holding a spinlock.
The function call paths (from bottom to top) in Linux-4.16.7 are:
[FUNC] msleep
drivers/usb/gadget/udc/r8a66597-udc.c, 839:
msleep in init_controller
drivers/usb/gadget/udc/r8a66597-udc.c, 96:
init_controller in r8a66597_usb_disconnect
drivers/usb/gadget/udc/r8a66597-udc.c, 93:
spin_lock in r8a66597_usb_disconnect
[FUNC] msleep
drivers/usb/gadget/udc/r8a66597-udc.c, 835:
msleep in init_controller
drivers/usb/gadget/udc/r8a66597-udc.c, 96:
init_controller in r8a66597_usb_disconnect
drivers/usb/gadget/udc/r8a66597-udc.c, 93:
spin_lock in r8a66597_usb_disconnect
To fix these bugs, msleep() is replaced with mdelay().
This bug is found by my static analysis tool (DSAC-2) and checked by
my code review.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The current code is broken as it re-defines "req" inside the
if block, then goto out of it. Thus the request that ends
up being sent is not the one that was populated by the
code in question.
This fixes RNDIS driver autodetect by Windows 10 for me.
The bug was introduced by Chris rework to remove the local
queuing inside the if { } block of the redefined request.
Fixes: 636ba13aec ("usb: gadget: composite: remove duplicated code in OS desc handling")
Cc: <stable@vger.kernel.org> # v4.17
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
A couple of bugs in the driver are preventing SETUP packets
with an OUT data phase from working properly.
Interestingly those are incredibly rare (RNDIS typically
uses them and thus is broken without this fix).
The main problem was an incorrect register offset being
applied for arming RX on EP0. The other problem relates
to stalling such a packet before the data phase, in which
case we don't get an ACK cycle, and get the next SETUP
packet directly, so we shouldn't reject it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Drop redundant input-speed re-encoding at every open(). The output and
input speeds are initialised to the same value and are kept in sync on
termios updates.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Variables iflag, mask and serial are being assigned but are never used
hence are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'iflag' set but not used [-Wunused-but-set-variable]
warning: variable 'mask' set but not used [-Wunused-but-set-variable]
warning: variable 'serial' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The device (a POS terminal) implements CDC ACM, but has not union
descriptor.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQEwBAABCAAaBQJbRA8GExxwZXRlci5jaGVuQG54cC5jb20ACgkQSFkpgVDWcbsE
Ygf/QAv1RHor7dx2XO0p2lfVSscQegsoXFobtRhItfmwbS1i/P5iavfMqIxRosBh
xac2hHwGSn3isAMRfak3oyKbyrVKo0MYnHHKiQAc1U6X//DQCYfZ933H5wEzXj8q
KvPPPmMLrD5EAgkNcNruYMx0/Onwch/azR+njozVGFpZWfRkAURePGeb0dCTZl/f
/+1Sa3J28No62cUpKrqs55/POjaHSibY8D9iwlQxImkeaBtJNTohevkEUfJunbJ3
0VVWgfEh4BpuInVv6Wu7UzjggRPUrfhozny6qxfHfNpc/RLkZtzcDLD5IsOy3vHc
8cRtU/AamMX3J/tOiAC1tSOSaQ==
=hohq
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-linus
Peter writes:
One regression fix causes imx51 board hang when using ULPI PHY
Variable maxpacket is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'maxpacket' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pointer dev is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'dev' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable num_ports is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'num_ports' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable t is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 't' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pointer dbc is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
variable 'dbc' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable 'selector' is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'selector' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable modey is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'modey' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pointer usbdev is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'usbdev' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pointer ep is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'ep' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver was apparently never tested with an actual KLSI device. In
fact, even the device-id entry which was supposed to allow for this had
a typo in it.
Tests now reveal that the predicted firmware differences with the
PalmConnect adapters are real and that the driver does not support KLSI
devices with PID 0x000c, so let's remove the broken entry.
Reported-by: Chris Jakob <chris.jakob@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
At over 4000 #includes, <linux/platform_device.h> is the 9th most
#included header file in the Linux kernel. It does not need
<linux/mod_devicetable.h>, so drop that header and explicitly add
<linux/mod_devicetable.h> to source files that need it.
4146 #include <linux/platform_device.h>
After this patch, there are 225 files that use <linux/mod_devicetable.h>,
for a reduction of around 3900 times that <linux/mod_devicetable.h>
does not have to be read & parsed.
225 #include <linux/mod_devicetable.h>
This patch was build-tested on 20 different arch-es.
It also makes these drivers SubmitChecklist#1 compliant.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <lkp@intel.com> # drivers/media/platform/vimc/
Reported-by: kbuild test robot <lkp@intel.com> # drivers/pinctrl/pinctrl-u300.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In general, accessing userspace memory beyond the length of the supplied
buffer in VFS read/write handlers can lead to both kernel memory corruption
(via kernel_read()/kernel_write(), which can e.g. be triggered via
sys_splice()) and privilege escalation inside userspace.
Fix it by using simple_read_from_buffer() instead of custom logic.
Fixes: 6bc235a2e2 ("USB: add driver for Meywa-Denki & Kayac YUREX")
Signed-off-by: Jann Horn <jannh@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a condition check about the PLL acvice of this
controller. Otherwise, the controller might cause hang when
any USB clocks are not supplied yet and accesses the xHCI registers.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch simplifies getting the firmware name for R-Car Gen3.
Almost all R-Car Gen3 USB3.0 Host controllers use "V3". But,
r8a7795 ES1.x SoCs only should use "V2". Since the xhci-plat already
has the firmware_name of R-Car Gen3 as "V3", the xhci-rcar doesn't
need some members of rcar_quirks_match.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To clean up the xhci-rcar.c code later, this patch adds firmware_name
"V3" for R-Car Gen3.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gcc-8 points out that the fix-byte buffer might be too small if
desc->mode is a three-digit number:
drivers/usb/typec/class.c: In function 'typec_register_altmode':
drivers/usb/typec/class.c:502:32: error: '%d' directive writing between 1 and 3 bytes into a region of size 2 [-Werror=format-overflow=]
sprintf(alt->group_name, "mode%d", desc->mode);
^~
drivers/usb/typec/class.c:502:27: note: directive argument in the range [0, 255]
sprintf(alt->group_name, "mode%d", desc->mode);
^~~~~~~~
drivers/usb/typec/class.c:502:2: note: 'sprintf' output between 6 and 8 bytes into a destination of size 6
sprintf(alt->group_name, "mode%d", desc->mode);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
I assume this cannot happen in practice, but we can simply make the
string long enough to avoid the warning. This uses the two padding
bytes that already exist after the string.
Fixes: 4ab8c18d4d ("usb: typec: Register a device for every mode")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One of the error handling paths forgets to unlock dp->lock on the error
exit path leading to a potential lock-up. Also the return path for a
successful call to the function configuration_store can return an
uninitialized error return code if dp->alt->active is false, so ensure
ret is zeroed on the successful exit path to avoid garbage being returned.
Detected by CoverityScan, CID#1471597 ("Unitialized scalar variable")
Fixes: 0e3bb7d689 ("usb: typec: Add driver for DisplayPort alternate mode")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pointer adev is being dereferenced before it is being sanity
checked with a null pointer check, hence it is possible for
a null pointer dereference to occur. Fix this by dereferencing
adev only once it is null checked.
Detected by CoverityScan, CID#1471598 ("Dereference before null check")
Fixes: 8a37d87d72 ("usb: typec: Bus type for alternate modes")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Corsair Strafe appears to suffer from the same issues
as the Corsair Strafe RGB.
Apply the same quirks (control message delay and init delay)
that the RGB version has to 1b1c:1b15.
With these quirks in place the keyboard works correctly upon
booting the system, and no longer requires reattaching the device.
Signed-off-by: Nico Sneck <snecknico@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The > should be >= here so that we don't read one element beyond the end
of the ep->stream_info->stream_rings[] array.
Fixes: e9df17eb14 ("USB: xhci: Correct assumptions about number of rings per endpoint.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without that option, we run into a link failure:
drivers/usb/gadget/udc/aspeed-vhub/hub.o: In function `ast_vhub_std_hub_request':
hub.c:(.text+0x5b0): undefined reference to `usb_gadget_get_string'
Fixes: 7ecca2a408 ("usb/gadget: Add driver for Aspeed SoC virtual hub")
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are three fixes for broken control-transfer error handling, which
could lead to uninitialised slab data leaking to user space.
Included is also a new device id for cp210x.
All but the final two patches have been in linux-next with no reported
issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=UDQ5
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.18-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
USB-serial fixes for v4.18-rc4
Here are three fixes for broken control-transfer error handling, which
could lead to uninitialised slab data leaking to user space.
Included is also a new device id for cp210x.
All but the final two patches have been in linux-next with no reported
issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
Add missing version-request error handling and suppress printing of the
(zeroed) transfer-buffer content in case of errors.
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to return -EIO in case of a short modem-status read request.
While at it, split the debug message to not include the (zeroed)
transfer-buffer content in case of errors.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
Add missing transfer-length sanity check to the status-register
completion handler to avoid leaking bits of uninitialised slab data to
user space.
Fixes: 3f5429746d ("USB: Moschip 7840 USB-Serial Driver")
Cc: stable <stable@vger.kernel.org> # 2.6.19
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix broken modem-status error handling which could lead to bits of slab
data leaking to user space.
Fixes: 3b36a8fd67 ("usb: fix uninitialized variable warning in keyspan_pda")
Cc: stable <stable@vger.kernel.org> # 2.6.27
Signed-off-by: Johan Hovold <johan@kernel.org>
The led trigger core learned a few things that allow to simplify the
trigger drivers. Make use of automated trigger attributes and error
checking of the activate callback. Also use the wrappers to set and get
trigger_data.
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Given that activating a trigger can fail, let the callback return an
indication. This prevents to have a trigger active according to the
"trigger" sysfs attribute but not functional.
All users are changed accordingly to return 0 for now. There is no intended
change in behaviour.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Commit 03e6275ae3 ("usb: chipidea: Fix ULPI on imx51") causes a kernel
hang on imx51 systems that use the ULPI interface and do not select the
CONFIG_USB_CHIPIDEA_ULPI option.
In order to avoid such potential misuse, let's always build the
chipidea ULPI code into the final ci_hdrc object.
Tested on a imx51-babbage board.
Fixes: 03e6275ae3 ("usb: chipidea: Fix ULPI on imx51")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
There are two versions of the Qivicon Zigbee stick in circulation. This
adds the second USB ID to the cp210x driver.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The "r" variable is an int and "bufsize" is an unsigned int so the
comparison is type promoted to unsigned. If usb_control_msg() returns a
negative that is treated as a high positive value and the error handling
doesn't work.
Fixes: 2d5a9c72d0 ("USB: serial: ch341: fix control-message error handling")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Since most target drivers do not use the second fabric_make_tpg() argument
("group") and since it is trivial to derive the group pointer from the wwn
pointer, do not pass the group pointer to fabric_make_tpg().
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The set_current_limit tcpm_dev callback is optional and the tcpm core
will already log the passed in values, so there is no need to have an
empty implementation of this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Comparing an int to a size, which is unsigned, causes the int to become
unsigned, giving the wrong result. usb_get_descriptor can return a
negative error code.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
int x;
expression e,e1;
identifier f;
@@
*x = f(...);
... when != x = e1
when != if (x < 0 || ...) { ... return ...; }
*x < sizeof(e)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds more complete handling of VDMs and registration of
partner alternate modes, and introduces callbacks for
alternate mode operations.
Only DFP role is supported for now.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of the tcpm specific mux states, using the generic
USB Type-C connector state values, and with DisplayPort
using connector states defined for the DisplayPort Alt Mode.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DisplayPort USB Type-C Alt Mode allows DisplayPort displays
and adapters to be attached to the USB Type-C ports on the
system.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introducing a simple bus for the alternate modes. Bus allows
binding drivers to the discovered alternate modes the
partners support.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before a device was created for every discovered SVID, but
this will create a device for every discovered mode of every
SVID. The idea is to make it easier to create mode specific
drivers once a bus for the alternate mode is added.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order for the muxes to be usable with alternate modes,
the alternate mode devices will need also to be able to get
a handle to the muxes on top of the port devices. To make
that possible, the muxes need to be possible to request with
an identifier.
This will change the API so that the mux identifier is given
as a function parameter to typec_mux_get(), and the hard-coded
"typec-mux" is replaced with that value.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f2a8aa053c ("typec: tcpm: Represent source supply through
power_supply") moved the code to register a power_supply representing
the device supplying power to the type-C connector, from the fusb302
code to the generic tcpm code so that we have a psy reporting the
supply voltage and current for all tcpm devices.
This broke the reporting of current and voltage through the psy interface
when supplied by a a non pd supply (5V, current as reported by
get_current_limit). The cause of this breakage is port->supply_voltage
and port->current_limit not being set in that case.
This commit fixes this by setting port->supply_voltage and
port->current_limit from tcpm_set_current_limit().
This commit also removes setting supply_voltage and current_limit
from tcpm_reset_port() as that calls tcpm_set_current_limit(0, 0)
which now already sets these to 0.
Fixes: f2a8aa053c ("typec: tcpm: Represent source supply through...")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pm_runtime_put_sync() gets called everytime in xhci_dbc_stop().
If dbc is not started, this makes the runtime PM counter incorrectly
becomes 0, and calls autosuspend function. Then we'll keep seeing this:
[54664.762220] xhci_hcd 0000:00:14.0: Root hub is not suspended
So only calls pm_runtime_put_sync() when dbc was started.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds function typec_get_orientation() that can be used
for checking the current cable plug orientation.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move TCPCI(Typec port controller interface) driver and rt1711h
driver out of staging.
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As DRP port autonomously toggles the Rp/Rd need a start value to
begin with, so add one parameter for it in tcpm_start_drp_toggling.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support of get typec and power delivery config from
firmware description.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Li Jun <jun.li@nxp.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds 3 APIs to get the typec port power and data type,
and preferred power role by its name string.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add fwnode handle to get the fwnode so we can get typec configs
it contains.
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the quest to remove all stack VLA usage from the kernel[1], this
uses the maximum buffer size and adds a sanity check. While 25 bytes
is the size of the largest current things coming through, Heikki
Krogerus pointed out that the actual max in 64 bytes, as per ch 1.3.2
http://www.ti.com/lit/ug/slvuan1a/slvuan1a.pdf
[1] https://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.com
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Cc: Oliver Neukum <oneukum@suse.com>
Cc: "Bjørn Mork" <bjorn@mork.no>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the code path
__usb_hcd_giveback_urb()
-> wdm_in_callback()
-> service_outstanding_interrupt()
The function service_outstanding_interrupt() will unconditionally enable
interrupts during unlock and invoke usb_submit_urb() with GFP_KERNEL.
If the HCD completes in BH (like ehci does) then the context remains
atomic due local_bh_disable() and enabling interrupts does not change
this.
Defer the error case handling to a workqueue as suggested by Oliver
Neukum. In case of an error the worker performs the read out and wakes
the user.
Fixes: c1da59dad0 ("cdc-wdm: Clear read pipeline in case of error")
Cc: Robert Foss <robert.foss@collabora.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Cc: Juergen Stuber <starblue@users.sourceforge.net>
Cc: legousb-devel@lists.sourceforge.net
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The intr_idx_lock lock is acquired only in the completion callback of
the ->int_in_urb (iowarrior_callback()). There is only one URB that is
scheduled / completed so there can't be more than one user of the lock.
The comment says that it protects ->intr_idx and the callback is the
only place in driver that writes to it.
Remove the intr_idx_lock lock because it is superfluous.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wa_urb_dequeue() locks multiple spinlocks while disabling interrupts:
spin_lock_irqsave(&lock1, flags);
spin_lock_irqsave(&lock2, flags2);
Obviously there is no need for the second irqsave and "flags2" variable
since interrupts are disabled at that point. Remove the second irqsave:
spin_lock_irqsave(&lock1, flags);
spin_lock(&lock2);
and eliminate the flags2 variable.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Cc: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We accidentally return 1 instead of negative error codes.
Fixes: df44831ee2 ("USB host: Add USB ehci support for nuvoton npcm7xx platform")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Avi Fishman <AviFishman70@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are bunch of new device ids for cp210x.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=+oP9
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.18-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.18-rc3
Here are bunch of new device ids for cp210x.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
Add a "tty_" prefix to the tty "flag" variable to avoid any future
mixups with the recently added irq-mask "flags" one.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
The portdata spinlock can be taken in interrupt context (via
sierra_outdat_callback()).
Disable interrupts when taking the portdata spinlock when discarding
deferred URBs during close to prevent a possible deadlock.
Fixes: 014333f77c ("USB: sierra: fix urb and memory leak on disconnect")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
[ johan: amend commit message and add fixes and stable tags ]
Signed-off-by: Johan Hovold <johan@kernel.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
USB Ethernet gadget now works on Tegra114 and Tegra124.
Similar to commit 061e20e989 ("usb: chipidea: tegra: Use aligned DMA
on Tegra30").
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The commit 4e88d4c083 ("usb: add a flag to skip PHY
initialization to struct usb_hcd") delete the assignment
for hcd->usb_phy, it causes usb_phy_notify_connect{disconnect)
are not called, the USB PHY driver is not notified of hot plug
event, then the disconnection will not be detected by hardware.
Fixes: 4e88d4c083 ("usb: add a flag to skip PHY initialization
to struct usb_hcd")
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reported-by: Mats Karrman <mats.dev.list@gmail.com>
Tested-by: Mats Karrman <mats.dev.list@gmail.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
This patch adds support for ehci controller for the Nuvoton
npcm7xx platform.
Most of the code was taken from ehci-spear.c + specific initialization
code
Signed-off-by: Avi Fishman <AviFishman70@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cdc-acm driver does not have a refcount of itself, but uses a
tty_port's refcount. That is, if the refcount of tty_port is '0', we
can clean up the cdc-acm driver by calling the .destruct()
callback function of struct tty_port_operations.
The problem is the destruct() callback function is not called if
the probe() fails, because tty_port's refcount is not zero. So,
add tty_port_put() when probe() fails.
Signed-off-by: Jaejoong Kim <climbbb.kim@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The two do the same thing, but we want to remove getnstimeofday64()
to have a more consistent interface.
It would be nice to use a monotonic clocksource here rather than
'real' time, but that would break the user interface.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for the new get_resuming_ports HCD method to
the xhci-hcd driver.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for the new get_resuming_ports HCD method to
the ehci-hcd driver.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a USB device attached to a root-hub port sends a wakeup request
to a sleeping system, we do not report the wakeup event to the PM
core. This is because a system resume involves waking up all
suspended USB ports as quickly as possible; without the normal
USB_RESUME_TIMEOUT delay, the host controller driver doesn't set the
USB_PORT_STAT_C_SUSPEND flag and so usb_port_resume() doesn't realize
that a wakeup request was received.
However, some environments (such as Chrome OS) want to have all wakeup
events reported so they can be ascribed to the appropriate device. To
accommodate these environments, this patch adds a new routine to the
hub driver and a corresponding new HCD method to be used when a root
hub resumes. The HCD method returns a bitmap of ports that have
initiated a wakeup signal but not yet completed resuming. The hub
driver can then report to the PM core that the child devices attached
to these ports initiated a wakeup event.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Suggested-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port->logbuffer_head may be wrong if the two processes enters
_tcpm_log at the mostly same time. The 2nd process enters _tcpm_log
before the 1st process update the index, then the 2nd process will
not allocate logbuffer, when the 2nd process tries to use log buffer,
the index has already updated by the 1st process, so it will get
NULL pointer for updated logbuffer, the error message like below:
tcpci 0-0050: Log buffer index 6 is NULL
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tcpm_set_state() function take msecs not jiffies.
Fixes: f0690a25a1 ("staging: typec: USB Type-C Port Manager (tcpm)")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to UCSI Specification, Connector Change Event only
means a change in the Connector Status and Operation Mode
fields of the STATUS data structure. So any other change
should create another event.
Unfortunately on some platforms the firmware acting as PPM
(platform policy manager - usually embedded controller
firmware) still does not report any other status changes if
there is a connector change event. So if the connector power
or data role was changed when a device was plugged to the
connector, the driver does not get any indication about
that. The port will show wrong roles if that happens.
To fix the issue, always checking the data and power role
together with a connector change event.
Fixes: c1b0bc2dab ("usb: typec: Add support for UCSI interface")
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes an issue where the driver fails with an error:
ioremap error for 0x3f799000-0x3f79a000, requested 0x2, got 0x0
On some platforms the UCSI ACPI mailbox SystemMemory
Operation Region may be setup before the driver has been
loaded. That will lead into the driver failing to map the
mailbox region, as it has been already marked as write-back
memory. acpi_os_ioremap() for x86 uses ioremap_cache()
unconditionally.
When the issue happens, the embedded controller has a
pending query event for the UCSI notification right after
boot-up which causes the operation region to be setup before
UCSI driver has been loaded.
The fix is to notify acpi core that the driver is about to
access memory region which potentially overlaps with an
operation region right before mapping it.
acpi_release_memory() will check if the memory has already
been setup (mapped) by acpi core, and deactivate it (unmap)
if it has. The driver is then able to map the memory with
ioremap_nocache() and set the memtype to uncached for the
region.
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Fixes: 8243edf441 ("usb: typec: ucsi: Add ACPI driver")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some controllers take almost 55ms to complete controller
restore state (CRS).
There is no timeout limit mentioned in xhci specification so
fixing the issue by increasing the timeout limit to 100ms
[reformat code comment -Mathias]
Signed-off-by: Ajay Gupta <ajaykuee@gmail.com>
Signed-off-by: Nagaraj Annaiah <naga.annaiah@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The address-of operator will always evaluate to true. However,
power should be explicitly disabled if no power domain is used.
Remove the address-of operator.
Fixes: 58c38116c6 ("usb: xhci: tegra: Add support for managing powergates")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initialize the 'err' variate to remove the build warning,
the warning is shown as below:
drivers/usb/host/xhci-tegra.c: In function 'tegra_xusb_mbox_thread':
drivers/usb/host/xhci-tegra.c:552:6: warning: 'err' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/host/xhci-tegra.c:482:6: note: 'err' was declared here
Fixes: e84fce0f88 ("usb: xhci: Add NVIDIA Tegra XUSB controller driver")
Signed-off-by: Dongjiu Geng <gengdongjiu@huawei.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't rely on event interrupt (EINT) bit alone to detect pending port
change in resume. If no change event is detected the host may be suspended
again, oterwise roothubs are resumed.
There is a lag in xHC setting EINT. If we don't notice the pending change
in resume, and the controller is runtime suspeded again, it causes the
event handler to assume host is dead as it will fail to read xHC registers
once PCI puts the controller to D3 state.
[ 268.520969] xhci_hcd: xhci_resume: starting port polling.
[ 268.520985] xhci_hcd: xhci_hub_status_data: stopping port polling.
[ 268.521030] xhci_hcd: xhci_suspend: stopping port polling.
[ 268.521040] xhci_hcd: // Setting command ring address to 0x349bd001
[ 268.521139] xhci_hcd: Port Status Change Event for port 3
[ 268.521149] xhci_hcd: resume root hub
[ 268.521163] xhci_hcd: port resume event for port 3
[ 268.521168] xhci_hcd: xHC is not running.
[ 268.521174] xhci_hcd: handle_port_status: starting port polling.
[ 268.596322] xhci_hcd: xhci_hc_died: xHCI host controller not responding, assume dead
The EINT lag is described in a additional note in xhci specs 4.19.2:
"Due to internal xHC scheduling and system delays, there will be a lag
between a change bit being set and the Port Status Change Event that it
generated being written to the Event Ring. If SW reads the PORTSC and
sees a change bit set, there is no guarantee that the corresponding Port
Status Change Event has already been written into the Event Ring."
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Negative error code will be larger than sizeof().
Note that none of these bugs prevent errors from being detected, even if
the ir-usb one would cause a less precise debug message to printed.
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
[ johan: add comment about implications ]
Signed-off-by: Johan Hovold <johan@kernel.org>
The sbitmap and the percpu_ida perform essentially the same task,
allocating tags for commands. The sbitmap outperforms the percpu_ida as
documented here: https://lkml.org/lkml/2014/4/22/553
The sbitmap interface is a little harder to use, but being able to remove
the percpu_ida code and getting better performance justifies the additional
complexity.
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com> # f_tcm
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Introduce target_free_tag() and convert all drivers to use it.
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
PID bitfield in descriptor should be set based on particular request
length, not based on EP's mc value. PID value can't be set to 0 even
request length is 0.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Freed allocated request for ep0 to prevent memory leak in case when
dwc2_driver_probe() failed.
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It happens when enable debug log, if set_alt() returns
USB_GADGET_DELAYED_STATUS and usb_composite_setup_continue()
is called before increasing count of @delayed_status,
so fix it by using spinlock of @cdev->lock.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Tested-by: Jay Hsu <shih-chieh.hsu@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If isoc split in transfer with no data (the length of DATA0
packet is zero), we can't simply return immediately. Because
the DATA0 can be the first transaction or the second transaction
for the isoc split in transaction. If the DATA0 packet with no
data is in the first transaction, we can return immediately.
But if the DATA0 packet with no data is in the second transaction
of isoc split in transaction sequence, we need to increase the
qtd->isoc_frame_index and giveback urb to device driver if needed,
otherwise, the MDATA packet will be lost.
A typical test case is that connect the dwc2 controller with an
usb hs Hub (GL852G-12), and plug an usb fs audio device (Plantronics
headset) into the downstream port of Hub. Then use the usb mic
to record, we can find noise when playback.
In the case, the isoc split in transaction sequence like this:
- SSPLIT IN transaction
- CSPLIT IN transaction
- MDATA packet (176 bytes)
- CSPLIT IN transaction
- DATA0 packet (0 byte)
This patch use both the length of DATA0 and qtd->isoc_split_offset
to check if the DATA0 is in the second transaction.
Tested-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Minas Harutyunyan hminas@synopsys.com>
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The commit 3bc04e28a0 ("usb: dwc2: host: Get aligned DMA in
a more supported way") rips out a lot of code to simply the
allocation of aligned DMA. However, it also introduces a new
issue when use isoc split in transfer.
In my test case, I connect the dwc2 controller with an usb hs
Hub (GL852G-12), and plug an usb fs audio device (Plantronics
headset) into the downstream port of Hub. Then use the usb mic
to record, we can find noise when playback.
It's because that the usb Hub uses an MDATA for the first
transaction and a DATA0 for the second transaction for the isoc
split in transaction. An typical isoc split in transaction sequence
like this:
- SSPLIT IN transaction
- CSPLIT IN transaction
- MDATA packet
- CSPLIT IN transaction
- DATA0 packet
The DMA address of MDATA (urb->dma) is always DWORD-aligned, but
the DMA address of DATA0 (urb->dma + qtd->isoc_split_offset) may
not be DWORD-aligned, it depends on the qtd->isoc_split_offset (the
length of MDATA). In my test case, the length of MDATA is usually
unaligned, this cause DATA0 packet transmission error.
This patch use kmem_cache to allocate aligned DMA buf for isoc
split in transaction. Note that according to usb 2.0 spec, the
maximum data payload size is 1023 bytes for each fs isoc ep,
and the maximum allowable interrupt data payload size is 64 bytes
or less for fs interrupt ep. So we set the size of object to be
1024 bytes in the kmem cache.
Tested-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Minas Harutyunyan hminas@synopsys.com>
Signed-off-by: William Wu <william.wu@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The dwc2_get_ls_map() use ttport to reference into the
bitmap if we're on a multi_tt hub. But the bitmaps index
from 0 to (hub->maxchild - 1), while the ttport index from
1 to hub->maxchild. This will cause invalid memory access
when the number of ttport is hub->maxchild.
Without this patch, I can easily meet a Kernel panic issue
if connect a low-speed USB mouse with the max port of FE2.1
multi-tt hub (1a40:0201) on rk3288 platform.
Fixes: 9f9f09b048 ("usb: dwc2: host: Totally redo the microframe scheduler")
Cc: <stable@vger.kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Minas Harutyunyan hminas@synopsys.com>
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case when a hub is connected to DWC2 host
auto suspend occurs and host goes to
hibernation. When any device connected to hub
host hibernation exiting incorrectly.
- Added dwc2_hcd_rem_wakeup() function call to
exit from suspend state by remote wakeup.
- Increase timeout value for port suspend bit to be set.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The #ifdef guards around these are wrong, resulting in warnings
in certain configurations:
drivers/usb/dwc3/dwc3-qcom.c:244:12: error: 'dwc3_qcom_resume' defined but not used [-Werror=unused-function]
static int dwc3_qcom_resume(struct dwc3_qcom *qcom)
^~~~~~~~~~~~~~~~
drivers/usb/dwc3/dwc3-qcom.c:223:12: error: 'dwc3_qcom_suspend' defined but not used [-Werror=unused-function]
static int dwc3_qcom_suspend(struct dwc3_qcom *qcom)
This replaces the guards with __maybe_unused annotations to shut up
the warnings and give better compile time coverage.
Fixes: a4333c3a6b ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix to return error code -ENODEV from the get device failed error
handling case instead of 0, as done elsewhere in this function.
Fixes: a4333c3a6b ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In ISOC OUT transfer, when the OUT token received while EP disabled,
we shouldn't complete a usb request. The current flow completed one
usb request, this will lead to a packet drop to function driver.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Commit fe8abf332b ("usb: dwc3: support clocks and resets for DWC3 core")
adds support for handling clocks and resets in the DWC3 core, so that for
platforms following the standard devicetree bindings this does not need
to be duplicated in all the different glue layers.
These changes intended for devicetree based platforms introduce an
uncoditional clk_bulk_get() in the core probe path. This leads to the
following error being logged on x86/ACPI systems:
[ 26.276783] dwc3 dwc3.3.auto: Failed to get clk 'ref': -2
This commits wraps the clk_bulk_get() in an if (dev->of_node) check so
that it only is done on devicetree instantiated devices, fixing this
error.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In ISOC transfer, when the NAK interrupt happens, we shouldn't complete
a usb request, the current flow will complete one usb request with no
hardware transfer, this will lead to a packet drop on the usb bus.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Zeng Tao <prime.zeng@hisilicon.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The clocks have already been explicitly disabled and put as part of
remove() so the runtime suspend callback must not be run when balancing
the runtime PM usage count before returning.
Fixes: 16adc674d0 ("usb: dwc3: add generic OF glue layer")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case of requests queue is empty reset EP target_frame to
initial value.
This allow restarting ISOC traffic in case when function
driver queued requests with interruptions.
Tested-by: Zeng Tao <prime.zeng@hisilicon.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Silicon Labs defines alternative VID/PID pairs for some chips that when
used will automatically install drivers for Windows users without manual
intervention. Unfortunately, these IDs are not recognized by the Linux
module, so using these IDs improves user experience on one platform but
degrades it on Linux. This patch addresses this problem.
Signed-off-by: Karoly Pados <pados@pados.hu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This is a late set of changes from Deepa Dinamani doing an automated
treewide conversion of the inode and iattr structures from 'timespec'
to 'timespec64', to push the conversion from the VFS layer into the
individual file systems.
There were no conflicts between this and the contents of linux-next
until just before the merge window, when we saw multiple problems:
- A minor conflict with my own y2038 fixes, which I could address
by adding another patch on top here.
- One semantic conflict with late changes to the NFS tree. I addressed
this by merging Deepa's original branch on top of the changes that
now got merged into mainline and making sure the merge commit includes
the necessary changes as produced by coccinelle.
- A trivial conflict against the removal of staging/lustre.
- Multiple conflicts against the VFS changes in the overlayfs tree.
These are still part of linux-next, but apparently this is no longer
intended for 4.18 [1], so I am ignoring that part.
As Deepa writes:
The series aims to switch vfs timestamps to use struct timespec64.
Currently vfs uses struct timespec, which is not y2038 safe.
The series involves the following:
1. Add vfs helper functions for supporting struct timepec64 timestamps.
2. Cast prints of vfs timestamps to avoid warnings after the switch.
3. Simplify code using vfs timestamps so that the actual
replacement becomes easy.
4. Convert vfs timestamps to use struct timespec64 using a script.
This is a flag day patch.
Next steps:
1. Convert APIs that can handle timespec64, instead of converting
timestamps at the boundaries.
2. Update internal data structures to avoid timestamp conversions.
Thomas Gleixner adds:
I think there is no point to drag that out for the next merge window.
The whole thing needs to be done in one go for the core changes which
means that you're going to play that catchup game forever. Let's get
over with it towards the end of the merge window.
[1] https://www.spinics.net/lists/linux-fsdevel/msg128294.html
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=CZX2
-----END PGP SIGNATURE-----
Merge tag 'vfs-timespec64' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/playground
Pull inode timestamps conversion to timespec64 from Arnd Bergmann:
"This is a late set of changes from Deepa Dinamani doing an automated
treewide conversion of the inode and iattr structures from 'timespec'
to 'timespec64', to push the conversion from the VFS layer into the
individual file systems.
As Deepa writes:
'The series aims to switch vfs timestamps to use struct timespec64.
Currently vfs uses struct timespec, which is not y2038 safe.
The series involves the following:
1. Add vfs helper functions for supporting struct timepec64
timestamps.
2. Cast prints of vfs timestamps to avoid warnings after the switch.
3. Simplify code using vfs timestamps so that the actual replacement
becomes easy.
4. Convert vfs timestamps to use struct timespec64 using a script.
This is a flag day patch.
Next steps:
1. Convert APIs that can handle timespec64, instead of converting
timestamps at the boundaries.
2. Update internal data structures to avoid timestamp conversions'
Thomas Gleixner adds:
'I think there is no point to drag that out for the next merge
window. The whole thing needs to be done in one go for the core
changes which means that you're going to play that catchup game
forever. Let's get over with it towards the end of the merge window'"
* tag 'vfs-timespec64' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/playground:
pstore: Remove bogus format string definition
vfs: change inode times to use struct timespec64
pstore: Convert internal records to timespec64
udf: Simplify calls to udf_disk_stamp_to_time
fs: nfs: get rid of memcpys for inode times
ceph: make inode time prints to be long long
lustre: Use long long type to print inode time
fs: add timespec64_truncate()
- Use overflow helpers in 2-factor allocators (Kees, Rasmus)
- Introduce overflow test module (Rasmus, Kees)
- Introduce saturating size helper functions (Matthew, Kees)
- Treewide use of struct_size() for allocators (Kees)
-----BEGIN PGP SIGNATURE-----
Comment: Kees Cook <kees@outflux.net>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=/3L8
-----END PGP SIGNATURE-----
Merge tag 'overflow-v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull overflow updates from Kees Cook:
"This adds the new overflow checking helpers and adds them to the
2-factor argument allocators. And this adds the saturating size
helpers and does a treewide replacement for the struct_size() usage.
Additionally this adds the overflow testing modules to make sure
everything works.
I'm still working on the treewide replacements for allocators with
"simple" multiplied arguments:
*alloc(a * b, ...) -> *alloc_array(a, b, ...)
and
*zalloc(a * b, ...) -> *calloc(a, b, ...)
as well as the more complex cases, but that's separable from this
portion of the series. I expect to have the rest sent before -rc1
closes; there are a lot of messy cases to clean up.
Summary:
- Introduce arithmetic overflow test helper functions (Rasmus)
- Use overflow helpers in 2-factor allocators (Kees, Rasmus)
- Introduce overflow test module (Rasmus, Kees)
- Introduce saturating size helper functions (Matthew, Kees)
- Treewide use of struct_size() for allocators (Kees)"
* tag 'overflow-v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
treewide: Use struct_size() for devm_kmalloc() and friends
treewide: Use struct_size() for vmalloc()-family
treewide: Use struct_size() for kmalloc()-family
device: Use overflow helpers for devm_kmalloc()
mm: Use overflow helpers in kvmalloc()
mm: Use overflow helpers in kmalloc_array*()
test_overflow: Add memory allocation overflow tests
overflow.h: Add allocation size calculation helpers
test_overflow: Report test failures
test_overflow: macrofy some more, do more tests for free
lib: add runtime test of check_*_overflow functions
compiler.h: enable builtin overflow checkers and add fallback code
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kmalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kmalloc(struct_size(instance, entry, count), GFP_KERNEL);
This patch makes the changes for kmalloc()-family (and kvmalloc()-family)
uses. It was done via automatic conversion with manual review for the
"CHECKME" non-standard cases noted below, using the following Coccinelle
script:
// pkey_cache = kmalloc(sizeof *pkey_cache + tprops->pkey_tbl_len *
// sizeof *pkey_cache->table, GFP_KERNEL);
@@
identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc";
expression GFP;
identifier VAR, ELEMENT;
expression COUNT;
@@
- alloc(sizeof(*VAR) + COUNT * sizeof(*VAR->ELEMENT), GFP)
+ alloc(struct_size(VAR, ELEMENT, COUNT), GFP)
// mr = kzalloc(sizeof(*mr) + m * sizeof(mr->map[0]), GFP_KERNEL);
@@
identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc";
expression GFP;
identifier VAR, ELEMENT;
expression COUNT;
@@
- alloc(sizeof(*VAR) + COUNT * sizeof(VAR->ELEMENT[0]), GFP)
+ alloc(struct_size(VAR, ELEMENT, COUNT), GFP)
// Same pattern, but can't trivially locate the trailing element name,
// or variable name.
@@
identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc";
expression GFP;
expression SOMETHING, COUNT, ELEMENT;
@@
- alloc(sizeof(SOMETHING) + COUNT * sizeof(ELEMENT), GFP)
+ alloc(CHECKME_struct_size(&SOMETHING, ELEMENT, COUNT), GFP)
Signed-off-by: Kees Cook <keescook@chromium.org>
Here is the driver core patchset for 4.18-rc1.
The large chunk of these are firmware core documentation and api
updates. Nothing major there, just better descriptions for others to be
able to understand the firmware code better. There's also a user for a
new firmware api call.
Other than that, there are some minor updates for debugfs, kernfs, and
the driver core itself.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWxbZAg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykbiACgu/2qqou1iV4GxOkvrj5wfsHD+lYAoNPNNDHu
Qf3CCEKbxogF6YowDiAH
=Dsqq
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the driver core patchset for 4.18-rc1.
The large chunk of these are firmware core documentation and api
updates. Nothing major there, just better descriptions for others to
be able to understand the firmware code better. There's also a user
for a new firmware api call.
Other than that, there are some minor updates for debugfs, kernfs, and
the driver core itself.
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (23 commits)
driver core: hold dev's parent lock when needed
driver-core: return EINVAL error instead of BUG_ON()
driver core: add __printf verification to device_create_groups_vargs
mm: memory_hotplug: use put_device() if device_register fail
base: core: fix typo 'can by' to 'can be'
debugfs: inode: debugfs_create_dir uses mode permission from parent
debugfs: Re-use kstrtobool_from_user()
Documentation: clarify firmware_class provenance and why we can't rename the module
Documentation: remove stale firmware API reference
Documentation: fix few typos and clarifications for the firmware loader
ath10k: re-enable the firmware fallback mechanism for testmode
ath10k: use firmware_request_nowarn() to load firmware
firmware: add firmware_request_nowarn() - load firmware without warnings
firmware_loader: make firmware_fallback_sysfs() print more useful
firmware_loader: move kconfig FW_LOADER entries to its own file
firmware_loader: replace ---help--- with help
firmware_loader: enhance Kconfig documentation over FW_LOADER
firmware_loader: document firmware_sysfs_fallback()
firmware: rename fw_sysfs_fallback to firmware_fallback_sysfs()
firmware: use () to terminate kernel-doc function names
...
Here is the big USB pull request for 4.18-rc1.
Lots of stuff here, the highlights are:
- phy driver updates and new additions
- usual set of xhci driver updates
- normal set of musb updates
- gadget driver updates and new controllers
- typec work, it's getting closer to getting fully out of the
staging portion of the tree.
- lots of minor cleanups and bugfixes.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWxba6w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykumQCg2abWE5LijR0SNJIwX8xk64HLUAMAnAxBZDG3
aB0GyOQd54L+09q4LAdn
=ZCEx
-----END PGP SIGNATURE-----
Merge tag 'usb-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB and PHY updates from Greg KH:
"Here is the big USB pull request for 4.18-rc1.
Lots of stuff here, the highlights are:
- phy driver updates and new additions
- usual set of xhci driver updates
- normal set of musb updates
- gadget driver updates and new controllers
- typec work, it's getting closer to getting fully out of the staging
portion of the tree.
- lots of minor cleanups and bugfixes.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
Revert "xhci: Reset Renesas uPD72020x USB controller for 32-bit DMA issue"
xhci: Add quirk to zero 64bit registers on Renesas PCIe controllers
xhci: Allow more than 32 quirks
usb: xhci: force all memory allocations to node
selftests: add test for USB over IP driver
USB: typec: fsusb302: no need to check return value of debugfs_create_dir()
USB: gadget: udc: s3c2410_udc: no need to check return value of debugfs_create functions
USB: gadget: udc: renesas_usb3: no need to check return value of debugfs_create functions
USB: gadget: udc: pxa27x_udc: no need to check return value of debugfs_create functions
USB: gadget: udc: gr_udc: no need to check return value of debugfs_create functions
USB: gadget: udc: bcm63xx_udc: no need to check return value of debugfs_create functions
USB: udc: atmel_usba_udc: no need to check return value of debugfs_create functions
USB: dwc3: no need to check return value of debugfs_create functions
USB: dwc2: no need to check return value of debugfs_create functions
USB: core: no need to check return value of debugfs_create functions
USB: chipidea: no need to check return value of debugfs_create functions
USB: ehci-hcd: no need to check return value of debugfs_create functions
USB: fhci-hcd: no need to check return value of debugfs_create functions
USB: fotg210-hcd: no need to check return value of debugfs_create functions
USB: imx21-hcd: no need to check return value of debugfs_create functions
...
This reverts commit 8466489ef5.
Now that we can properly reset the uPD72020x without a hard PCI reset,
let's get rid of the existing quirks.
Tested-by: Domenico Andreoli <domenico.andreoli@linux.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Faiz Abbas <faiz_abbas@ti.com>
Tested-by: Domenico Andreoli <domenico.andreoli@linux.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some Renesas controllers get into a weird state if they are reset while
programmed with 64bit addresses (they will preserve the top half of the
address in internal, non visible registers).
You end up with half the address coming from the kernel, and the other
half coming from the firmware.
Also, changing the programming leads to extra accesses even if the
controller is supposed to be halted. The controller ends up with a fatal
fault, and is then ripe for being properly reset. On the flip side,
this is completely unsafe if the defvice isn't behind an IOMMU, so
we have to make sure that this is the case. Can you say "broken"?
This is an alternative method to the one introduced in 8466489ef5
("xhci: Reset Renesas uPD72020x USB controller for 32-bit DMA issue"),
which will subsequently be removed.
Tested-by: Domenico Andreoli <domenico.andreoli@linux.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Faiz Abbas <faiz_abbas@ti.com>
Tested-by: Domenico Andreoli <domenico.andreoli@linux.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We now have 32 different quirks, and the field that holds them
is full. Let's bump it up to the next stage so that we can handle
some more... The type is now an unsigned long long, which is 64bit
on most architectures.
We take this opportunity to change the quirks from using (1 << x)
to BIT_ULL(x).
Tested-by: Domenico Andreoli <domenico.andreoli@linux.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Faiz Abbas <faiz_abbas@ti.com>
Tested-by: Domenico Andreoli <domenico.andreoli@linux.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xhci driver forces DMA memory to be node aware, however, there are
several ring-related memory allocations that are not memory node aware.
This patch resolves those *alloc functions to be allocated on the proper
memory node.
Signed-off-by: Adam Wallis <awallis@codeaurora.org>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Clean up the fsusb302 driver to not care if the root directory was
created, as the code should work properly either way.
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Li Yang <leoyang.li@nxp.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
There is also no need to keep the file dentries around at all, so remove
those variables from the device structure.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Felipe Balbi <balbi@kernel.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
There is also no need to keep the file dentries around at all, so remove
those variables from the device structure.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Jaejoong Kim <climbbb.kim@gmail.com>
Cc: Li Yang <leoyang.li@nxp.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
There is also no need to keep the file dentries around at all, so remove
those variables from the device structure.
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
There is also no need to keep the file dentries around at all, so remove
those variables from the device structure.
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Felipe Balbi <balbi@kernel.org>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Johan Hovold <johan@kernel.org>
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
There is also no need to keep the file dentries around at all, so remove
those variables from the host controller structure.
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Johan Hovold <johan@kernel.org>
Cc: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@intel.com>
Cc: Vasyl Gomonovych <gomonovych@gmail.com>
Cc: Mariusz Skamra <mariuszx.skamra@intel.com>
Cc: "Gustavo A. R. Silva" <garsilva@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
There is also no need to keep the file dentries around at all, so remove
those variables from the host controller structure.
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
We do need to save the dentries for these files, so keep them around,
but no need to check if they are "valid" or not, as the code works just
as well either way.
Cc: Pete Zaitcev <zaitcev@kotori.zaitcev.us>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Fredrik Noring <noring@nocrew.org>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Because of this, lots of init functions do not need to have return
values, so this cleans up a lot of unused error handling code that never
could have triggered in the past.
Cc: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Clean up the tcpm.c code to not care about this, turns out no one was
even checking the return value of this function, so it didn't matter.
Note, I do not think this code can be removed in a running system, as
the debugfs root directory will stick around, that should be fixed
someday...
Revieved-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A built-in PHY driver cannot link against modular USB core code:
drivers/usb/phy/phy-tegra-usb.o: In function `tegra_usb_phy_probe':
phy-tegra-usb.c:(.text+0x6bc): undefined reference to `usb_get_dr_mode'
This uses a 'select' statement in Kconfig like we have for other such
PHY drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the USB hub core waits for 50 ms after enumerating the
device. This was added to help "some high speed devices" to
enumerate (b789696af8 "[PATCH] USB: relax usbcore reset timings").
On some devices, the time-to-active is important, so we provide
a per-port option to reduce the time to what the USB specification
requires: 10 ms.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "old" enumeration scheme is considerably faster (it takes
~244ms instead of ~356ms to get the descriptor).
It is currently only possible to use the old scheme globally
(/sys/module/usbcore/parameters/old_scheme_first), which is not
desirable as the new scheme was introduced to increase compatibility
with more devices.
However, in our case, we care about time-to-active for a specific
USB device (which we make the firmware for), on a specific port
(that is pogo-pin based: not a standard USB port). This new
sysfs option makes it possible to use the old scheme on a single
port only.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix silly mistake when enabling runtime PM support for the Tegra XHCI
driver. If runtime PM was enabled correctly for the XHCI device, then
we should call pm_runtime_get_sync() to enable the device.
Fixes: ee9e5f4c78 ("usb: xhci: tegra: Add runtime PM support")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Workaround introduced for i.MX53 in be9cae2479 ("usb: chipidea:
imx: Fix ULPI on imx53") seems to be applicable in case of i.MX51 as
well. Running latest kernel on ZII RDU1 Board (imx51-zii-rdu1.dts)
exhibits a kernel frozen on PORTSC access and applying the workaround
resolves the issue.
Fixes: be9cae2479 ("usb: chipidea: imx: Fix ULPI on imx53")
Cc: Peter Chen <peter.chen@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Tested-By: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the only users of this variable got removed, we now get a
warning about 'otg' being unused:
drivers/usb/musb/da8xx.c: In function 'da8xx_musb_interrupt':
drivers/usb/musb/da8xx.c:226:19: error: unused variable 'otg' [-Werror=unused-variable]
Fixes: d2852f2d3e ("usb: musb: remove references to default_a of struct usb_otg")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It appears that a "#define DEBUG" was left in on the recent patch
landed for the Qualcomm DWC3 glue driver. Let's remove it.
Fixes: a4333c3a6b ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB Host Controller driver 'ohci-at91.c' reads a Special Function
Register - OHCI Interrupt Configuration Register (AT91_SFR_OHCIICR)
for bits SUSPEND_A/B/C. These bits are defined in sama5d2 alone, so
sfr register mapping is done with compatible string "atmel,sama5d2-sfr".
This gives a kernel warning 'failed to find sfr node' with non sama5d2
cpus which is removed here, thus leaving it up to having a proper DTS.
Signed-off-by: Prasanthi Chellakumar <prasanthi.chellakumar@microchip.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need to do extra endianness conversion in
usb_set_isoch_delay because it is already done
in usb_control_msg()
Fixes: 886ee36e72 ("usb: core: add support for USB_REQ_SET_ISOCH_DELAY")
Cc: Dmytro Panchenko <dmytro.panchenko@globallogic.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: stable <stable@vger.kernel.org> # v4.16+
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the USB-serial updates for 4.18-rc1, including:
- support for hardware-assisted XON/XOFF output flow control for pl2303
- fix for a long-standing IXON/IXOFF mixup in ftdi_sio
- blacklist of two apparently unused dwm-158 modem interfaces that
confused some user space daemon (option)
- add missing const to a tty helper currently used by USB serial only
Included are also various clean ups.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=gsOA
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.18-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.18-rc1
Here are the USB-serial updates for 4.18-rc1, including:
- support for hardware-assisted XON/XOFF output flow control for pl2303
- fix for a long-standing IXON/IXOFF mixup in ftdi_sio
- blacklist of two apparently unused dwm-158 modem interfaces that
confused some user space daemon (option)
- add missing const to a tty helper currently used by USB serial only
Included are also various clean ups.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
SoC have internal I/O buses that can't be proved for devices. The
devices on the buses can be accessed directly without additinal
configuration required. This type of bus is represented as
"simple-bus". In some platforms, we name "soc" with "simple-bus"
attribute and many devices are hooked under it described in DT
(device tree).
In commit bf74ad5bc4 ("Hold the device's parent's lock during
probe and remove") to solve USB subsystem lock sequence since
USB device's characteristic. Thus "soc" needs to be locked
whenever a device and driver's probing happen under "soc" bus.
During this period, an async driver tries to probe a device which
is under the "soc" bus would be blocked until previous driver
finish the probing and release "soc" lock. And the next probing
under the "soc" bus need to wait for async finish. Because of
that, driver's async probe for init time improvement will be
shadowed.
Since many devices don't have USB devices' characteristic, they
actually don't need parent's lock. Thus, we introduce a lock flag
in bus_type struct and driver core would lock the parent lock base
on the flag. For USB, we set this flag in usb_bus_type to keep
original lock behavior in driver core.
Async probe could have more benefit after this patch.
Signed-off-by: Martin Liu <liumartin@google.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Tegra XHCI controller requires that the XUSBA (for superspeed) and
XUSBC (for host) power-domains are enabled. Commit 8df127456f
("soc/tegra: pmc: Enable XUSB partitions on boot") was added to force
on these power-domains if the XHCI driver is enabled while proper
power-domain support is added, to ensure the device did not hang on
boot. However, rather than forcing on these power-domains in the PMC
driver we can use the legacy Tegra powergate APIs to turn on these
power-domains during the probe of the Tegra XHCI driver.
In the near future we plan to move the Tegra XHCI driver to use the
generic PM domain framework for power-domains and so to prepare for
this only use the legacy Tegra powergate API if there is not PM
domain associated with device (ie. dev.pm_domain is NULL). Please
note that in the future the superspeed and host resets will be handled
by the generic PM domain provider and so these are only these are only
needed in the case where there is no generic PM domain.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add runtime PM support to the Tegra XHCI driver and move the function
calls to enable/disable the clocks, regulators and PHY into the runtime
PM callbacks.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When adding runtime PM support to the Tegra XHCI driver, it is desirable
to move the function calls to enable the clocks, regulators and PHY from
the tegra_xusb_probe into the runtime PM handlers. Currently, the
clocks, regulators and PHY are all enabled before we call
usb_create_hcd() in tegra_xusb_probe(), however, we cannot call
pm_runtime_get_sync() at this point because the platform device data is
not yet initialised. Fortunately, the function usb_create_hcd() can be
called before we enable the clocks, regulators and PHY and so prepare
for adding runtime PM support, by moving the call to usb_create_hcd()
before we enable the hardware.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ALWAYS_SYNC flag is currently honored by the usb-storage driver but not UAS
and is required to work around devices that become unstable upon being
queried for cache. This code is taken straight from:
drivers/usb/storage/scsiglue.c:284
Signed-off-by: Alexander Kappner <agk@godking.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB Type-C PHY in Intel WhiskeyCove PMIC has build-in
USB Type-C state machine which we were relying on to
configure the CC lines correctly. This patch removes that
dependency and configures the CC line according to commands
from the port manager (tcpm.c) in wcove_set_cc().
This fixes an issue where USB devices attached to the USB
Type-C port do not get enumerated. When acting as
source/host, the HW FSM sometimes fails to configure the PHY
correctly.
Fixes: 3c4fb9f169 ("usb: typec: wcove: start using tcpm for USB PD support")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes an issue where the mux does not get configured
when the parent device is suspended. The registers for this
mux are mapped to the parent device MMIO (usually xHCI PCI
device), so in order for the driver to be able to program
the registers, the parent device must be resumed.
Reported-by: Sathyanarayanan Kuppuswamy <sathyanarayanan.kuppuswamy@intel.com>
Fixes: f6fb9ec02b ("usb: roles: Add Intel xHCI USB role switch driver")
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removing the "fusb302" debugfs directory when unloading
the driver. That allows the driver to be loaded more then
one time. The directory will not get actually removed until
it is empty, so only after the last instance has been
removed.
This fixes an issue where the driver can't be re-loaded if
it has been unloaded as the "fusb302" debugfs directory
already exists.
Fixes: 76f0c53d08 ("usb: typec: fusb302: Move out of staging")
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trying to determine the USB port type with this mux is very
difficult. To simplify the situation, always allow user
control, even if the port is USB Type-C port.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix htmldocs warning:
drivers/usb/typec/mux.c:186: warning: Function parameter or member 'mux' not described in
'typec_mux_unregister'
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: bdecb33af3 ("usb: typec: API for controlling USB Type-C Multiplexers")
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pdev_nr and rhport can be controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/usb/usbip/vhci_sysfs.c:238 detach_store() warn: potential spectre issue 'vhcis'
drivers/usb/usbip/vhci_sysfs.c:328 attach_store() warn: potential spectre issue 'vhcis'
drivers/usb/usbip/vhci_sysfs.c:338 attach_store() warn: potential spectre issue 'vhci->vhci_hcd_ss->vdev'
drivers/usb/usbip/vhci_sysfs.c:340 attach_store() warn: potential spectre issue 'vhci->vhci_hcd_hs->vdev'
Fix this by sanitizing pdev_nr and rhport before using them to index
vhcis and vhci->vhci_hcd_ss->vdev respectively.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When printer_write() calls usb_ep_queue(), a udc driver (e.g.
renesas_usbhs driver) may call usb_gadget_giveback_request() in
the udc .queue ops immediately. Then, printer_write() calls
list_add(&req->list, &dev->tx_reqs_active) wrongly. After that,
if we do unbind the printer driver, WARN_ON() happens in
printer_func_unbind() because the list entry is not removed.
So, this patch moves list_add(&req->list, &dev->tx_reqs_active)
calling before usb_ep_queue().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For supply registration, provide fwnode pointer of the port device,
via the power_supply_config structure, to allow other psy drivers
to add us as a supplier. At present this only applies to DT
based platforms using the 'power-supplies' DT property, but in the
future should also work for ACPI platforms when the relevant support
is added to the power_supply core.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The notifier callbacks of extcon are called in atomic context, but the
callbacks will call regulator_enable()/regulator_disable() which may
sleep caused by mutex, so use work queue to call the sleep functions.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When VBUS_FALL interrupt arises, it means U3 device is disconnected
with host, so need reset status of gadget
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clear test_mode flag when the gadget is reset by host, otherwise
will affect the next test item.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reset EP when disable it to reset data toggle for U2 EP, and
SeqN, flow control status etc for U3 EP, this can avoid
issue of uncontinuous SeqN
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the controller receives a LPM request, it will reject the LPM
request, and need software to re-enable it after LPM resume if the
controller doesn't remote wakeup from L1 automatically
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable compliance transition for a port by writing "compliance" to the
ports portsc file in debugfs.
port must be "Not-connected" and Link must be in RxDetect state to enable
compliance mode.
Only needed for host that have CTC flag set.
Allows state transitioning to compliance at 1st LFPS timeout.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add ports/portxx/portsc for each xHC hardware usb port to debugfs.
Showing the content of the port status and control register for
each port (PORTSC)
Portxx is numbered starting from 1 for historical reasons to better
match port numbering shown by lsusb and other places.
Ports in debugfs are in the order XHC controller has them,
In most cases USB2 ports come first, followed by USB3 ports.
i.e. USB2 ports are port01-portxx, and USB3 portxx-portmax.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As we are now using the new port strtuctes the port_arrays
are no longer needed, remove them completely
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_get_ports() is one of the last functions using port_arrays in
xhci-hub.c. We get the same data directly from hub and port structures
instead, so convert and remove both xhci_get_ports() and port_arrays from
all function that no longer need it.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
get rid of port iomem arrays and use port structures in the following
functions:
xhci_find_raw_port_number()
xhci_disable_port_wake_on_bits()
xhci_set_usb2_hardware_lpm()
xhci_all_ports_seen_u0()
compliance_mode_recovery()
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't use pointers to port array and port index as function parameters
in xhci_test_and_clear_bit(), just use a pointer to the right port
structure.
xhci_test_and_clear_bit() was the last port_array user in
xhci_get_port_status() and handle_port_status(), so remove the
port_array from them as well.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove old iomem port array and index as parameters, just
send a ponter to a port strucure instread
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hcd_portnum is a better desctiption than faked_port_index, and
is in line with the name the port structure uses.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
use port structures in the port event handler.
Getting the right hcd and hcd portnumber from the hardware port number
is a lot easier with port structures, and allows us to remove a lot
of the previous code, including the find_faked_portnum_from_hw_index()
function
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use port structures instead of mmio port arrays for
xhci_port_missing_cas_quirk() and xhci_set_remote_wake_mask() in
xhci-hub.c
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new port structures for functions in xhci-hub.c to get
port mmio address of portsc register instead of the port array
xhci_get_port_io_addr() is no longer needeed and is removed.
Plan is to get rid of the mmio port array completely.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
quick way to get the xhci roothub and thus all the ports
belonging to a certain hcd
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allows us to know the correct hcd a xhci roothub and its ports
belong to.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current way of having one array telling only the port speed,
and then two separate arrays with mmio addresses for usb2 and usb3 ports
requeres helper functions to transate hw to hcd, and hcd to hw port
numbers, and is hard to expand.
Instead create a structure describing a port, including the mmio address,
the port hardware index, hcd port index, and a pointer to the roothub
it belongs to.
Create one array containing all port structures in the same order the
hardware controller sees them. Then add an array of port pointers to
each xhci hub structure pointing to the ports that belonging to the
roothub.
This way we can easily convert hw indexed port events to usb core
hcd port numbers, and vice versa usb core hub hcd port numbers
to hw index and mmio address.
Other benefit is that we can easily find the parent hcd and xhci
structure of a port structure. This is useful in debugfs where
we can give one port structure pointer as parameter and get both
the correct mmio address and xhci lock needed to set some port
parameter.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds support for HiSilicon STB xHCI host controller.
There are two xHCI host controllers on HiSilicon STB SoCs. Each
one requires additional configuration before exposing interface
compliant with xHCI.
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Jianguo Sun <sunjianguo1@huawei.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A total of 98 non-merge commits, the biggest part being in dwc3 this
time around with a large refactoring of dwc3's transfer handling code.
We also have a new driver for Aspeed virtual hub controller.
Apart from that, just a list of miscellaneous fixes all over the place.
-----BEGIN PGP SIGNATURE-----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=b56m
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
usb: changes for v4.18 merge window
A total of 98 non-merge commits, the biggest part being in dwc3 this
time around with a large refactoring of dwc3's transfer handling code.
We also have a new driver for Aspeed virtual hub controller.
Apart from that, just a list of miscellaneous fixes all over the place.
UDC core ensures the usb_ep parameter passed in is not NULL, so
checking if (ep != NULL) is pointless.
Convert to_musb_ep() to a simple macro to not directly return NULL to
avoid warnings from code static analysis tools.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The gadget function drivers should ensure the usb_request parameter
passed in is not NULL. UDC core doesn't check if it is NULL, so MUSB
driver shouldn't have to check it either.
Convert to_musb_request() to a simple macro to not directly return NULL
to avoid warnings from code static analysis tools.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To be able to use DSPS-based controllers with device-tree descriptions
of the USB topology, we need to associate the glue device's device-tree
node with the child controller device.
Note that this can also be used to eventually let USB core manage
generic phys.
Also note that the other glue drivers will require similar changes to be
able to describe their buses in DT.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As decided in the discussion [1] we are deleting the otg protocol
support from the musb drivers.
First this patch disables the flags for enabling the otg protocols. We
will later gradually delete the otg protocol code from the musb drivers.
[1] https://www.spinics.net/lists/linux-usb/msg167003.html
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
musb drivers do not use the otg fsm framework, so referencing to
otg->default_a doesn't have any effect, so remove the references.
But tusb6010 glue driver uses it locally to control the vbus power, so
keep the references in tusb6010 only.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
musb_stage0_irq() is 400+ lines long. Break its interrupt events
handling into each individual functions to make it easy to read.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following members in struct musb_hdrc_config are not used,
so remove them.
soft_con
utm_16
big_endian
mult_bulk_tx
mult_bulk_rx
high_iso_tx
high_iso_rx
dma
dma_channels
dyn_fifo_size
vendor_ctrl
vendor_stat
vendor_req
dma_req_chan
musb_hdrc_eps_bits
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
include/linux/usb/musb.h already defines enum for musb port mode, so
remove the duplicate in musb_core.h and use the definition in musb.h.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
musb_core already has musb_get_mode(), so remove the duplicate from
musb_dsps.c.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both musb_io and musb_platform_ops in struct musb define a quirks flag
for the same purpose. Let's remove the one in struct musb_io, and use
that in struct musb_platform_ops instead.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following wrappers were defined because of Blackfin support. Now
Blackfin support is removed, these wrappers are no longer needed, so
remove them.
musb_write_txfifosz
musb_write_txfifoadd
musb_write_rxfifosz
musb_write_rxfifoadd
musb_write_ulpi_buscontrol
musb_read_txfifosz
musb_read_txfifoadd
musb_read_rxfifosz
musb_read_rxfifoadd
musb_read_ulpi_buscontrol
musb_read_hwvers
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now Blackfin support is removed, nobody uses adjust_channel_params() any
more, so remove it from struct musb_platform_ops.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now Blackfin support is removed, we no longer need function pointers for
musb_readl() and musb_writel().
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now Blackfin support is removed, header musbhsdma.h is only included in
musbhsdma.c. So let's merge the content in musbhsdma.h to musbhsdma.c
and delete musbhsdma.h.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support hardware-level Xon/Xoff flow control in transmit direction with
pl2303.
I only know how to get the hardware to do IXON/!IXANY with ^S/^Q as control
characters, so I preserve the old behaviour for all other cases.
Signed-off-by: Florian Zumbiehl <florz@florz.de>
[ johan: rewrite logic using pl2303_termios_change() helper ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Clean up the somewhat convoluted hardware-assisted flow control
handling.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop urb_ prefixes from value and index variables used in control
requests.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Replace all __u types with their u counterparts throughout the driver
(whose structures are not exported to user space).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Since forever this driver has had IXON and IXOFF mixed up, and has used
the latter rather than the former to enable hardware-assisted software
flow control on output.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
When _param is unsigned and the minimum value of range is 0, it gives
the following warning:
COVERITY NO_EFFECT: This less-than-zero comparison of an unsigned value
is never true.
Converting ._param to int to avoid this warning.
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes an issue that this driver cause double phy_put()
calling. This driver must not call phy_put() in the remove because
the driver calls devm_phy_get() in the probe.
Fixes: 279d4bc640 ("usb: gadget: udc: renesas_usb3: add support for generic phy")
Cc: <stable@vger.kernel.org> # v4.15+
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes an issue that reconnection is possible to fail
because unexpected state handling happens by the irqs. To fix the issue,
the driver disables the controller's irqs when disconnected.
Fixes: 746bfe63bb ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Cc: <stable@vger.kernel.org> # v4.5+
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes an issue that this driver ignores errors other than
the non-existence of the device, f.e. a memory allocation failure
in devm_phy_get(). So, this patch replaces devm_phy_get() with
devm_phy_optional_get().
Reported-by: Simon Horman <horms+renesas@verge.net.au>
Fixes: 279d4bc640 ("usb: gadget: udc: renesas_usb3: add support for generic phy")
Cc: <stable@vger.kernel.org> # v4.15+
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes an issue that this driver cannot call phy_init()
if a gadget driver is alreadly loaded because usb_add_gadget_udc()
might call renesas_usb3_start() via .udc_start.
This patch also revises the typo (s/an optional/optional/).
Fixes: 279d4bc640 ("usb: gadget: udc: renesas_usb3: add support for generic phy")
Cc: <stable@vger.kernel.org> # v4.15+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes an issue that this driver causes panic if a gadget
driver is already loaded because usb_add_gadget_udc() might call
renesas_usb3_start() via .udc_start, and then pm_runtime_get_sync()
in renesas_usb3_start() doesn't work correctly.
Note that the usb3_to_dev() macro should not be called at this timing
because the macro uses the gadget structure.
Fixes: cf06df3fae ("usb: gadget: udc: renesas_usb3: move pm_runtime_{en,dis}able()")
Cc: <stable@vger.kernel.org> # v4.15+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes an issue that this driver doesn't remove its debugfs.
Fixes: 43ba968b00 ("usb: gadget: udc: renesas_usb3: add debugfs to set the b-device mode")
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc3_ep_dequeue() waits for completion of End Transfer command using
wait_event_lock_irq(), which will release the dwc3->lock while waiting
and reacquire after completion. This allows a potential race condition
with ep_disable() which also removes all requests from started_list
and pending_list.
The check for NULL r->trb should catch this but currently it exits to
the wrong 'out1' label which calls dwc3_gadget_giveback(). Since its
list entry was already removed, if CONFIG_DEBUG_LIST is enabled a
'list_del corruption' bug is thrown since its next/prev pointers are
already LIST_POISON1/2. If r->trb is NULL it should simply exit to
'out0'.
Fixes: cf3113d893 ("usb: dwc3: gadget: properly increment dequeue pointer on ep_dequeue")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fixes the following sparse warning:
drivers/usb/dwc3/gadget.c:169:6: warning:
symbol 'dwc3_gadget_del_and_unmap_request' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix to return error code -ENOMEM from the alloc fail error handling
case instead of 0, as done elsewhere in this function.
Fixes: ecd29dabb2 ("usb: dwc2: pci: Handle error cleanup in probe")
Reviewed-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
By clearing NAK status of EP, core will send ZLP
to IN token and assert NAK interrupt relying
on TxFIFO status only.
The WA applies only to core versions from 2.72a
to 4.00a (including both). Also for FS_IOT_1.00a
and HS_IOT_1.00a.
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
devm_regulator_get_optional returns -ENODEV if the regulator isn't
there, so if that's the case we have to make sure not to leave -ENODEV
in the regulator pointer.
Also, make sure we return 0 in that case, but correctly propagate any
other errors. Also propagate the error from _dwc2_hcd_start.
Fixes: 531ef5ebea ("usb: dwc2: add support for host mode external vbus supply")
Cc: Amelie Delaunay <amelie.delaunay@st.com>
Reviewed-by: Amelie Delaunay <amelie.delaunay@st.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.
Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In 4.17-rc, commit 03ea6d6e9e ("usb: dwc2: Enable power down")
caused the HiKey board to not correctly handle switching between
usb-gadget and usb-host mode.
Unplugging the OTG port would result in:
[ 42.240973] dwc2 f72c0000.usb: dwc2_restore_host_registers: no host registers to restore
[ 42.249066] dwc2 f72c0000.usb: dwc2_host_exit_hibernation: failed to restore host registers
And the USB-host ports would not function.
And plugging in the OTG port, we would see:
[ 46.046557] WARNING: CPU: 3 PID: 6 at drivers/usb/dwc2/gadget.c:260 dwc2_hsotg_init_fifo+0x194/0x1a0
[ 46.055761] CPU: 3 PID: 6 Comm: kworker/u16:0 Not tainted 4.17.0-rc5-00030-ge67da8c #231
[ 46.055767] Hardware name: HiKey Development Board (DT)
[ 46.055784] Workqueue: dwc2 dwc2_conn_id_status_change
...
Thus, this patch sets the hisi params to disable the power_down
flag by default, and gets thing working again.
Cc: John Youn <johnyoun@synopsys.com>
Cc: Vardan Mikayelyan <mvardan@synopsys.com>
Cc: Artur Petrosyan <arturp@synopsys.com>
Cc: Grigor Tovmasyan <tovmasya@synopsys.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added descriptions for all not described parameters.
Fix all kernel doc's warnings.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Introduce FSL_USB2_PHY_UTMI_DUAL in gadget driver for setting
phy in SOCs with utmi dual phy
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Tested-by: Tiago Brusamarello <tbrusa@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix sparse warning
Fixes: 5f0b74e548 ("USB: dwc3: get extcon device by OF graph bindings")
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We dont' need to touch req->direction or req->epnum from
ep_queue(). It's enough that we initialize both fields from
alloc_request() and just keep them for the entire lifetime of the
request.
No functional changes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of *always* calling dwc3_gadget_ep_get_transfer_index() after
sending a Start Transfer command, we can call it once from
dwc3_send_gadget_ep_cmd() itself.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of returning resource index number just to assign it to a
field inside 'dep' which was passed as argument, we can assing
dep->resource_index from inside dwc3_gadget_ep_get_transfer_index()
itself.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case we have many started requests and one of them in the middle is
completed with Missed Isoc, let's not End Transfer as that would
result in us loosing (possibly) many more intervals.
Instead, let's allow the controller to go through its list of started
requests.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
XferNotReady and XferInProgress give us the uFrame number we're
currently in. Printing that out on tracepoints may help us find bugs
in transfer scheduling.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Avoid a prototype when the function can be defined earlier. No
functional changes, cleanup only.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of having a prototype for a function that's defined a few
lines down, let's just move definition to the place where prototype
was.
No functional changes, cleanup only.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In a few places, the argument is completely unnecessary. On places
where it's needed, we can get it from dep->dwc.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Those two arguments refer to a single bitfield in the register. In
order to simplify the code, we can combine them into a single argument
and expect caller to pass the correct action argument at all times.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We will only have event status of IOC when IOC bit is set in
TRB. There's no need to check both bits.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We know that only OUT endpoints can trigger SHORT. We also know that
count MUST be > 0 whenever SHORT triggers.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This will make it easier to figure out the reason for the event. That
information really helps debugging certain problems.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We are trying to kick transfers on Isochronous endpoints in a more
controlled manner now. And this ended up rendering this piece of code
unnecessary.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
instead of having one big loop, let's split it down into two smaller
handlers: one for linear buffers and one for scatterlist.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
After all the previous changes, it's now a lot clearer how isoc
transfers should be managed. We don't need to try to End Transfers
from ep_queue since that's already done by cleanup_requests.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now, this part of the code is duplicated and brings no extra value to
the driver. Let's remove it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case we get an event with status set to Missed Isoc, this means we
have missed an isochronous interval and should issue End Transfer
command and wait for the following XferNotReady.
Let's do that early, rather than late.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
By now, it has the same semantics as DWC3_EP_TRANSFER_STARTED, but
that has a much more descriptive name.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We will need an up-to-date frame_number from XferInProgress too when
future patches improve our handling of Isoc endpoints.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The core requires the extra two bits of information for properly
scheduling Isochronous transfers. This means that we can't rely on
__dwc3_gadget_get_frame(). Let's always cache uFrame number from
XferNotReady instead.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Endpoint handlers need to know about endpoints, not dwc. If they
really need access to dwc (e.g. for printing error messages) we have a
reference to it tucked inside the endpoint.
This patch has no functional changes, it's simply moving things around.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We *KNOW* which events we enable for which endpoint types and
we *KNOW* when they'll trigger. The endpoint type checks are
pointless.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch simply renames two functions to more descriptive names so
that it's easier to understand what they're doing.
Cleanup only, no functional changes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of constantly calling kick transfer everything some event
shows up, let's just rely on the fact that we send Update Transfer
every time a new request is queued.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that we're making sure we don't have XferComplete events, we can
rename this function to what it actually handles:
dwc3_gadget_endpoint_transfer_in_progress()
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
XferComplete is enabled only for the default control pipe, let's make
that clear in the code.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We don't use XferNotReady for anything other than Default Control
Pipe, which is handled in ep0.c, and Isochronous endpoints. Let's make
that clear in the code.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Interrupt endpoints behave much like Bulk endpoints with the exception
that they are periodic. We can pre-issue Start Transfer exactly as we
do for Bulk endpoints.
While at that, remove one trailing blank line which is unnecessary.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The present code correctly fetches the req which were previously not
queued from the started_list but fails to continue queuing from the sg
where it previously stopped queuing (because of the unavailable TRB's).
This patch correct's the code to continue queuing from the correct sg
present in the sglist.
For example, consider 5 sgs in req. Because of limited TRB's among the
5 sgs only 3 got queued. This patch corrects the code to start queuing
from correct sg i.e 4th sg when the TRBs are available.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The code logic in dwc3_prepare_one_trb() incorrectly uses the address
and length fields present in req packet for mapping TRB's instead of
using the address and length fields of scattergather lists. This patch
correct's the code to use sg->address and sg->length when scattergather
lists are present.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
All T&M instruments should also work with rigol_quirk = 1 code path.
So remove unnecessary code in rigol_quirk = 0 code path to simplify the driver.
Tested-by: Dave Penkler <dpenkler@gmail.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We already have the tty port when probing a usb-serial port so use
tty_port_register_device() directly instead of tty_port_install() later
to set up the port link.
This is a step towards enabling serdev for usb-serial (but we need to
determine how to handle hotplugging first).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
stub_probe() calls put_busid_priv() in an error path when device isn't
found in the busid_table. Fix it by making put_busid_priv() safe to be
called with null struct bus_id_priv pointer.
This problem happens when "usbip bind" is run without loading usbip_host
driver and then running modprobe. The first failed bind attempt unbinds
the device from the original driver and when usbip_host is modprobed,
stub_probe() runs and doesn't find the device in its busid table and calls
put_busid_priv(0 with null bus_id_priv pointer.
usbip-host 3-10.2: 3-10.2 is not in match_busid table... skip!
[ 367.359679] =====================================
[ 367.359681] WARNING: bad unlock balance detected!
[ 367.359683] 4.17.0-rc4+ #5 Not tainted
[ 367.359685] -------------------------------------
[ 367.359688] modprobe/2768 is trying to release lock (
[ 367.359689]
==================================================================
[ 367.359696] BUG: KASAN: null-ptr-deref in print_unlock_imbalance_bug+0x99/0x110
[ 367.359699] Read of size 8 at addr 0000000000000058 by task modprobe/2768
[ 367.359705] CPU: 4 PID: 2768 Comm: modprobe Not tainted 4.17.0-rc4+ #5
Fixes: 22076557b0 ("usbip: usbip_host: fix NULL-ptr deref and use-after-free errors") in usb-linus
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
extcon device is used to detect host/device connection. Since extcon
OF property is deprecated, alternative method should be added.
This method uses OF graph bindings to locate extcon.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Historically, the clocks and resets are handled on the glue layer
side instead of the DWC3 core. For simple cases, dwc3-of-simple.c
takes care of arbitrary number of clocks and resets. The DT node
structure typically looks like as follows:
dwc3-glue {
compatible = "foo,dwc3";
clocks = ...;
resets = ...;
...
dwc3 {
compatible = "snps,dwc3";
...
};
}
By supporting the clocks and the reset in the dwc3/core.c, it will
be turned into a single node:
dwc3 {
compatible = "foo,dwc3", "snps,dwc3";
clocks = ...;
resets = ...;
...
}
This commit adds the binding of clocks and resets specific to this IP.
The number of clocks should generally be the same across SoCs, it is
just some SoCs either tie clocks together or do not provide software
control of some of the clocks.
I took the clock names from the Synopsys datasheet: "ref" (ref_clk),
"bus_early" (bus_clk_early), and "suspend" (suspend_clk).
I found only one reset line in the datasheet, hence the reset-names
property is omitted.
Those clocks are required for new platforms. Enforcing the new
binding breaks existing platforms since they specify clocks (and
resets) in their glue layer node, but nothing in the core node.
I listed such exceptional cases in the DT binding. The driver
code has been relaxed to accept no clock. This change is based
on the discussion [1].
I inserted reset_control_deassert() and clk_bulk_enable() before the
first register access, i.e. dwc3_cache_hwparams().
[1] https://patchwork.kernel.org/patch/10284265/
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Just set up the show callback in the tty_operations, and use
proc_create_single_data to create the file without additional
boilerplace code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Variants of proc_create{,_data} that directly take a seq_file show
callback and drastically reduces the boilerplate code in the callers.
All trivial callers converted over.
Signed-off-by: Christoph Hellwig <hch@lst.de>
usbip_host updates device status without holding lock from stub probe,
disconnect and rebind code paths. When multiple requests to import a
device are received, these unprotected code paths step all over each
other and drive fails with NULL-ptr deref and use-after-free errors.
The driver uses a table lock to protect the busid array for adding and
deleting busids to the table. However, the probe, disconnect and rebind
paths get the busid table entry and update the status without holding
the busid table lock. Add a new finer grain lock to protect the busid
entry. This new lock will be held to search and update the busid entry
fields from get_busid_idx(), add_match_busid() and del_match_busid().
match_busid_show() does the same to access the busid entry fields.
get_busid_priv() changed to return the pointer to the busid entry holding
the busid lock. stub_probe(), stub_disconnect() and stub_device_rebind()
call put_busid_priv() to release the busid lock before returning. This
changes fixes the unprotected code paths eliminating the race conditions
in updating the busid entries.
Reported-by: Jakub Jirasek
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After removing usbip_host module, devices it releases are left without
a driver. For example, when a keyboard or a mass storage device are
bound to usbip_host when it is removed, these devices are no longer
bound to any driver.
Fix it to run device_attach() from the module exit routine to restore
the devices to their original drivers. This includes cleanup changes
and moving device_attach() code to a common routine to be called from
rebind_store() and usbip_host_exit().
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device is left in the busid_table after unbind and rebind. Rebind
initiates usb bus scan and the original driver claims the device.
After rescan the device should be deleted from the busid_table as
it no longer belongs to usbip_host.
Fix it to delete the device after device_attach() succeeds.
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refine probe and disconnect debug msgs to be useful and say what is
in progress.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the fallout of the conversion to GPIO descriptors in 3df0340810.
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The include defines the private platform_data structure used with AVR
platforms. It has no user since 7c55984e19. Remove it.
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When converting to GPIO descriptors, gpiod_get_value automatically
handles the line inversion flags from the device tree.
Do not invert the line twice.
Fixes: 3df0340810 ("usb: gadget: udc: atmel: convert to use GPIO descriptors")
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
A message can be forged to crash the stack; here we make sure we don't
completely break the system if this occurs
Signed-off-by: Michel Pollet <michel.pollet@bp.renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It is not a good idea to directly modify the resource of a platform
device. Modify its local copy, and pass it to devm_ioremap_resource()
so that we do not need to restore it in the failure path and the remove
hook.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The USB3CV version 2.1.80 (March 26, 2018) requires all devices
( gen1, gen2, single lane, dual lane) to return the value of 0x0320
in the bcdUSB field
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some PHY drivers (e.g. for Qualcomm QUSB2 and QMP PHYs) support
runtime PM to reduce PHY power consumption during bus_suspend.
Add changes to let core auto-suspend PHYs on host bus-suspend
using GUSB2PHYCFG register if needed for a platform. Also perform
PHYs runtime suspend/resume and let platform glue drivers e.g.
dwc3-qcom handle remote wakeup during bus suspend by waking up
devices on receiving wakeup event from PHY.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
DWC3 controller on Qualcomm SOCs has a Qscratch wrapper.
Some of its uses are described below resulting in need to
have a separate glue driver instead of using dwc3-of-simple:
- It exposes register interface to override vbus-override
and lane0-pwr-present signals going to hardware. These
must be updated in peripheral mode for DWC3 if vbus lines
are not connected to hardware block. Otherwise RX termination
in SS mode or DP pull-up is not applied by device controller.
- pwr_events_irq_stat support to check if USB2 PHY is in L2 state
before glue driver proceeds with suspend.
- Support for wakeup interrupts lines that are asserted whenever
there is any wakeup event on USB3 or USB2 bus.
- Support to replace pip3 clock going to DWC3 with utmi clock
for hardware configuration where SSPHY is not used with DWC3.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add compatible string to use this generic glue layer to support
Allwinner H6 platform's dwc3 controller.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case there are multiple ecm instances, either for multiple
otg controllers, or multiple virtual links using libcomposite,
each instance needs to have its own host mac address string
value for iMACAddress.
Update the source array (ecm_string_defs), every time before
usb_gstrings_attach(). Without that, all links wrongly were
getting the same, last allocated, host mac address, rather
than the correct one, as requested via configfs.
Signed-off-by: Lukasz Nowak <lukasz.nowak@exablue.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fixes: <b3e3893e1253> ("net: use core MTU range checking")
which patched only one of two functions used to setup the
USB Gadget Ethernet driver, causing a serious performance
regression in the ability to increase mtu size above 1500.
Signed-off-by: John Greb <h3x4m3r0n@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The current frame_number is read from core for both
device and host modes. Reading of the current frame
number needs to be performed ASAP due to IRQ latency's.
This is why, it is moved to common interrupt handler.
Accordingly updated dwc2_gadget_target_frame_elapsed()
function which uses stored frame_number instead of
reading frame number.
In cases when target frame value is incremented
the frame_number is required to read again.
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Dumping the registers via debugfs makes USB on Raspberry Pi completely
unusable. The read of register GRXSTSP ("Receive Status Read and Pop
Register") is responsible for this behaviour, because it pops the RX FIFO.
So avoid this by omitting the relevant register.
CC: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Fixes: 563cf017c4 ("usb: dwc2: debugfs: add support for complete register dump")
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Crash caused by going out of "eps_out" array range.
Iteration on "eps_out" changed to less than "num_of_eps".
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added GHWCFG4_IPG_ISOC_SUPPORTED and DCFG_IPG_ISOC_SUPPORDED
bits definitions to enable/disable IPG feature.
Added ipg_isoc_en core parameter which will indicate IPG support
enable/disable and initialize it.
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In DDMA mode required to enable BNA interrupt for
both directions.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Changed existing two descriptor-chain flow to one chain.
In two-chain implementation BNA interrupt used for switching between
two chains. BNA interrupt asserted because of returning to
beginning of the chain based on L-bit of last descriptor.
Because of that we lose packets. This issue resolved by using one
desc-chain.
Removed all staff related to two desc-chain flow from
DDMA ISOC related functions.
Removed request length checking from dwc2_gadget_fill_isoc_desc()
function. Request length checking added to dwc2_hsotg_ep_queue()
function. If request length greater than descriptor limits then
request not added to queue. Additional checking done for High
Bandwidth ISOC OUT's which not supported by driver. In
dwc2_gadget_fill_isoc_desc() function also checked desc-chain
status (full or not) to avoid of reusing not yet processed
descriptors.
In dwc2_gadget_start_isoc_ddma() function creation of desc-chain
always started from descriptor 0. Before filling descriptors, they
were initialized by HOST BUSY status.
In dwc2_gadget_complete_isoc_request_ddma() added checking for
desc-chain rollover. Also added checking completion status.
Request completed successfully if DEV_DMA_STS is DEV_DMA_STS_SUCC,
otherwise complete with actual=0. For systems with high IRQ latency
added pointer compl_desc to next descriptor to be completed by
XferCompl interrupt. This pointer replace descriptor index calculation
based on DxEPDMA register. On descriptor completion interrupt
processing all descriptors starting from compl_desc till descriptor
which Buffer Status field not equal DMA_DONE status.
Actually removed dwc2_gadget_start_next_isoc_ddma() function because
now driver use only one desc-chain and instead that function added
dwc2_gadget_handle_isoc_bna() function for handling BNA interrupts.
Handling BNA interrupt done by flushing TxFIFOs for OUT EPs,
completing request with actual=0 and resetting desc-chain number and
target frame to initial values for restarting transfers.
On handling NAK request completed with actual=0. Incremented target
frame to allow fill desc chain and start transfers.
In DDMA mode avoided of frame number incrementing, because tracking
of frame number performed in dwc2_gadget_fill_isoc_desc() function.
When core assert XferCompl along with BNA, we should ignore XferCompl
in dwc2_hsotg_epint() function.
On BNA interrupt replaced dwc2_gadget_start_next_isoc_ddma() by above
mentioned BNA handler.
In dwc2_hsotg_ep_enable() function added sanity check of bInterval
for ISOC IN in DDMA mode, because HW doesn't supported EP's with
bInterval more than 10 and check for mc for ISOC OUT transfers,
because core doesn't support high bandwidth transfers.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In fact the driver depends on EXTCON only when it's configed as
USB_MTU3_DUAL_ROLE, so make USB_MTU3_DUAL_ROLE depend on EXTCON but
not USB_MTU3.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There is an error dialog popped up in PC when test TEST_J/K
by EHSETT tool, due to not waiting for the completion of
control transfer. Here fix it by entering test mode after
Status Stage finish.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When boot on the platform with the USB cable connected to Win7,
the Win7 will pop up an error dialog: "USB Device not recognized",
but finally the Win7 can enumerate it successfully.
The root cause is as the following:
When the xHCI driver set PORT_POWER of the OTG port, and if both
IDPIN and VBUS_VALID are high at the same time, the MTU3 controller
will set SESSION and pull up DP, so the Win7 can detect existence
of USB device, but if the mtu3 driver can't switch to device mode
during the debounce time, the Win7 can not enumerate it.
Here to fix it by removing the 1s delayed EXTCON register to speed up
mode switch.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The usb_add_gadget_udc() will set the gadget state as
USB_STATE_NOTATTACHED, so we needn't set it again.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The variable of 'count' is declared as u8, this will cause an issue
due to value truncated when works in SS or SSP mode and data length
is greater than 255, so change it as u32.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Tegra's EHCI driver has a build dependency on Tegra's PHY driver and
currently Tegra's PHY driver is built only when Tegra's EHCI driver is
built. Add own Kconfig entry for the Tegra's PHY driver so that drivers
other than ehci-tegra (like ChipIdea UDC) could work with ehci-tegra
driver being disabled in kernels config by allowing user to manually
select the PHY driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
UTMI pads are shared by USB controllers and reset of UTMI pads is shared
with the reset of USB1 controller. Currently reset of UTMI pads is done by
the EHCI driver and ChipIdea UDC works because EHCI driver always happen
to be probed first. Move reset controls from ehci-tegra to tegra-phy in
order to resolve the problem.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Tegra's PHY driver has a mix of pr_err() and dev_err(), let's switch to
dev_err() and use common errors message formatting across the driver for
consistency.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This allows 32 bit owners of ffs endpoints to
make ioctls into a 64 bit kernel.
All of the current epfile ioctls can be handled
with the same struct definitions as regular
ioctl.
Acked-by: Michał Nazarewicz <mina86@mina86.com>
Signed-off-by: Jerry Zhang <zhangjerry@google.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Currently, the midi function is not freed until it is
both removed from the config and released by the user.
Since the user could take a long time to release the
card, it's possible that the function could be unlinked
and thus f_midi_opts would be null when freeing f_midi.
Thus, refcount f_midi_opts and only free it when it is
unlinked and all f_midis have been freed.
Signed-off-by: Jerry Zhang <zhangjerry@google.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The Aspeed BMC SoCs support a "virtual hub" function. It provides some
HW support for a top-level USB2 hub behind which sit 5 gadget "ports".
This driver adds support for the full functionality, emulating the
hub standard requests and exposing 5 UDC gadget drivers corresponding
to the ports.
The hub itself has HW provided dedicated EP0 and EP1 (the latter for
hub interrupts). It also has dedicated EP0s for each function. For
other endpoints, there's a pool of 15 "generic" endpoints that are
shared among the ports.
The driver relies on my previous patch adding a "dispose" EP op to
handle EP allocation between ports. EPs are allocated from the shared
pool in the UDC "match_ep" callback and assigned to the UDC instance
(added to the gadget ep_list).
When the composite driver gets unbound, the new hook will allow the UDC
to clean things up and return those EPs to the shared pool.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The table is never modified by the function. This allows us
to use it on a statically defined table that is marked const.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It has been observed that writing 0xF2 to the power register while it
reads as 0xF4 results in the register having the value 0xF0, i.e. clearing
RESUME and setting SUSPENDM in one go does not work. It might also violate
the USB spec to transition directly from resume to suspend, especially
when not taking T_DRSMDN into account. But this is what happens when a
remote wakeup occurs between SetPortFeature USB_PORT_FEAT_SUSPEND on the
root hub and musb_bus_suspend being called.
This commit returns -EBUSY when musb_bus_suspend is called while remote
wakeup is signalled and thus avoids to reset the RESUME bit. Ignoring
this error when musb_port_suspend is called from musb_hub_control is ok.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hub driver will try to disable a USB3 device twice at logical disconnect,
racing with xhci_free_dev() callback from the first port disable.
This can be triggered with "udisksctl power-off --block-device <disk>"
or by writing "1" to the "remove" sysfs file for a USB3 device
in 4.17-rc4.
USB3 devices don't have a similar disabled link state as USB2 devices,
and use a U3 suspended link state instead. In this state the port
is still enabled and connected.
hub_port_connect() first disconnects the device, then later it notices
that device is still enabled (due to U3 states) it will try to disable
the port again (set to U3).
The xhci_free_dev() called during device disable is async, so checking
for existing xhci->devs[i] when setting link state to U3 the second time
was successful, even if device was being freed.
The regression was caused by, and whole thing revealed by,
Commit 44a182b9d1 ("xhci: Fix use-after-free in xhci_free_virt_device")
which sets xhci->devs[i]->udev to NULL before xhci_virt_dev() returned.
and causes a NULL pointer dereference the second time we try to set U3.
Fix this by checking xhci->devs[i]->udev exists before setting link state.
The original patch went to stable so this fix needs to be applied there as
well.
Fixes: 44a182b9d1 ("xhci: Fix use-after-free in xhci_free_virt_device")
Cc: <stable@vger.kernel.org>
Reported-by: Jordan Glover <Golden_Miller83@protonmail.ch>
Tested-by: Jordan Glover <Golden_Miller83@protonmail.ch>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's a fix for a long-standing issue in the visor driver, which could
have security implications. Included is also a new modem device id.
Both commits have been in linux-next for a couple of days with no
reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=jWQ/
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.17-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.17-rc4
Here's a fix for a long-standing issue in the visor driver, which could
have security implications. Included is also a new modem device id.
Both commits have been in linux-next for a couple of days with no
reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
This reverts commit 22072e83eb as it is
broken.
Alan writes:
What you can't see just from reading the patch is that in both
cases (ehci->itd_pool and ehci->sitd_pool) there are two
allocation paths -- the two branches of an "if" statement -- and
only one of the paths calls dma_pool_[z]alloc. However, the
memset is needed for both paths, and so it can't be eliminated.
Given that it must be present, there's no advantage to calling
dma_pool_zalloc rather than dma_pool_alloc.
Reported-by: Erick Cafferata <erick@cafferata.me>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Souptick Joarder <jrdr.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After removing usbip_host module, devices it releases are left without
a driver. For example, when a keyboard or a mass storage device are
bound to usbip_host when it is removed, these devices are no longer
bound to any driver.
Fix it to run device_attach() from the module exit routine to restore
the devices to their original drivers. This includes cleanup changes
and moving device_attach() code to a common routine to be called from
rebind_store() and usbip_host_exit().
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device is left in the busid_table after unbind and rebind. Rebind
initiates usb bus scan and the original driver claims the device.
After rescan the device should be deleted from the busid_table as
it no longer belongs to usbip_host.
Fix it to delete the device after device_attach() succeeds.
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the I2C adapter that the PD controller is attached to
does not support SMBus protocol, the driver needs to handle
block reads separately. The first byte returned in block
read protocol will show the total number of bytes. It needs
to be stripped away.
This is handled separately in the driver only because right
now we have no way of requesting the used protocol with
regmap-i2c. This is in practice a workaround for what is
really a problem in regmap-i2c. The other option would have
been to register custom regmap, or not use regmap at all,
however, since the solution is very simple, I choose to use
it in this case for convenience. It is easy to remove once
we figure out how to handle this kind of cases in
regmap-i2c.
Fixes: 0a4c005bd1 ("usb: typec: driver for TI TPS6598x USB Power Delivery controllers")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ref count for the USB role switch device must be
released after we are done using the switch.
Fixes: c6962c2972 ("usb: typec: tcpm: Set USB role switch to device mode when configured as such")
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some non-compliant high-speed USB devices have bulk endpoints with a
1024-byte maxpacket size. Although such endpoints don't work with
xHCI host controllers, they do work with EHCI controllers. We used to
accept these invalid sizes (with a warning), but we no longer do
because of an unintentional change introduced by commit aed9d65ac3
("USB: validate wMaxPacketValue entries in endpoint descriptors").
This patch restores the old behavior, so that people with these
peculiar devices can use them without patching their kernels by hand.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Suggested-by: Elvinas <elvinas@veikia.lt>
Fixes: aed9d65ac3 ("USB: validate wMaxPacketValue entries in endpoint descriptors")
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KASAN found a use-after-free in xhci_free_virt_device+0x33b/0x38e
where xhci_free_virt_device() sets slot id to 0 if udev exists:
if (dev->udev && dev->udev->slot_id)
dev->udev->slot_id = 0;
dev->udev will be true even if udev is freed because dev->udev is
not set to NULL.
set dev->udev pointer to NULL in xhci_free_dev()
The original patch went to stable so this fix needs to be applied
there as well.
Fixes: a400efe455 ("xhci: zero usb device slot_id member when disabling and freeing a xhci slot")
Cc: <stable@vger.kernel.org>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we get an invalid device configuration from a palm 3 type device, we
might incorrectly parse things, and we have the potential to crash in
"interesting" ways.
Fix this up by verifying the size of the configuration passed to us by
the device, and only if it is correct, will we handle it.
Note that this also fixes an information leak of slab data.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Reviewed-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ johan: add comment about the info leak ]
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This patch adds support for ublox R410M PID 0x90b2 USB modem to option
driver, this module supports LTE Cat M1 / NB1.
Interface layout:
0: QCDM/DIAG
1: ADB
2: AT
3: RMNET
Signed-off-by: SZ Lin (林上智) <sz.lin@moxa.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The dwm-158 interface 4 and 5 doesn't answer to the AT commands
and doesn't appears a option interface.
Tested on openwrt distribution (kernel 4.14 using the old blacklist
definitions).
Lars Melin also writes:
Blacklisting interface 4 and 5 is correct because:
MI_00 D-Link Mobile Broadband Device (cdc_ether)
MI_02 D-Link HSPA+DataCard Diagnostics Interface (also ppp modem)
MI_03 D-Link HSPA+DataCard NMEA Device
MI_04 D-Link HSPA+DataCard Speech Port
MI_05 D-Link HSPA+DataCard Debug Port
MI_06 USB Mass Storage Device
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
[ johan: add Lars's comment on the interface layout and reword summary ]
Cc: Lars Melin <larsm17@gmail.com>
Cc: Dan Williams <dcbw@redhat.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The usb_request pointer could be NULL in musb_g_tx(), where the
tracepoint call would trigger the NULL pointer dereference failure when
parsing the members of the usb_request pointer.
Move the tracepoint call to where the usb_request pointer is already
checked to solve the issue.
Fixes: fc78003e53 ("usb: musb: gadget: add usb-request tracepoints")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
musb_start_urb() doesn't check the pass-in parameter if it is NULL. But
in musb_bulk_nak_timeout() the parameter passed to musb_start_urb() is
returned from first_qh(), which could be NULL.
So wrap the musb_start_urb() call here with a if condition check to
avoid the potential NULL pointer dereference.
Fixes: f283862f3b ("usb: musb: NAK timeout scheme on bulk TX endpoint")
Cc: stable@vger.kernel.org # v3.7+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, logical and is being used instead of *bitwise* and.
Fix this by using a proper bitwise and operator.
Addresses-Coverity-ID: 1468455 ("Logical vs. bitwise operator")
Fixes: 64f7c494a3 ("typec: tcpm: Add support for sink PPS related messages")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Not much this time around: A list_del corruption on dwc3_ep_dequeue(),
sparse warning fix also on dwc3, build issues with f_phonet.
Apart from these three, some other minor fixes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
-----BEGIN PGP SIGNATURE-----
iQJRBAABCgA7FiEElLzh7wn96CXwjh2IzL64meEamQYFAlriz3odHGZlbGlwZS5i
YWxiaUBsaW51eC5pbnRlbC5jb20ACgkQzL64meEamQZp2w//e+9DHceBeKFyNiMD
LqCuvmygbAxnzCeLqyHQLLczRTCTjgOwt7Bh16PY0IwX3eUzBg5+r6TGLf1OUov/
W3kIPNQ8yN7tImItWc+Df5y5cUB2Pd5lhAxnNn6uUn8tQl7XBZ+XR9td53LMj7qd
KYSC2GtnegSvnudMLIUCzz6ZLuciPrcvxi56Vn+EwwDodKh48+rb5JXIG2gTfLTd
bQT9Lovjq7ieW45b10AOzSAYRAs/+QFCUfNctecr5jB8KNlGyDbGpXU7zlkOSOQv
E5QbtL/AgM68sEw9AnZgbRYf4ewCP29NDP/WVymMtH8viWNg7z95gaqBDc90ZmZw
K2NXASxjk9NkJRax6wN3ooz61y8I71bU6tc6PAi/P39C2fD9JcV1445rfQdHkWL8
1TpkEDTFHvyN8fYIz5uXnYU/bFx+oh4g7vzHnMZ+iv9rOWHera/Vh2VY7ThkKoC7
ASg0HQarBYQo3R4ARXcZ+Wag2uk/tbJXcGHlzJoc80Wo4dePgmiMGRuzZKA/be1R
M9niGkUCLUYW/NdeFbKCNySkD6knU6jhw8LeasxE1Uuv0YMsbXAAzaaba8CeuUrM
i7qHfB8airN8+Nk/88NQYecg9XXHiickhAWbA8ujqq3noG2xFzEZwL3RyhYI2Yfe
ZJ3AzAoS/KECTujEleoWR4dRIxQ=
=8ivE
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.17-rc3
Not much this time around: A list_del corruption on dwc3_ep_dequeue(),
sparse warning fix also on dwc3, build issues with f_phonet.
Apart from these three, some other minor fixes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This resolves the merge issue with drivers/usb/core/hcd.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trivial fix to spelling mistake in text string
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are a few device ids for -rc3, including a new "simple driver".
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=5u11
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.17-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.17-rc3
Here are a few device ids for -rc3, including a new "simple driver".
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
gcc thinks it is too smart and gives off a "you might be using this
variable before it is initialized" warning in tcpm_pd_build_request(),
because it can not follow the logic through the tcpm_pd_select_pdo()
call.
So just make gcc quiet by initializing things to 0, to prevent the
myriad of people complaining that we now have a build warning.
Cc: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds sink side support for Get_Status, Status,
Get_PPS_Status and PPS_Status handling. As there's the
potential for a partner to respond with Not_Supported,
handling of this message is also added. Sending of
Not_Supported is added to handle messagescreceived but not
yet handled.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds a power_supply class instance to represent a
PD source's voltage and current properties. This provides an
interface for reading these properties from user-space or other
drivers.
For PPS enabled Sources, this also provides write access to set
the current and voltage and allows for swapping between standard
PDO and PPS APDO.
As this represents a superset of the information provided in the
fusb302 driver, the power_supply instance in that code is removed
as part of this change, so reverting the commit titled
'typec: tcpm: Represent source supply through power_supply class'
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds code to handle requesting of PPS APDOs. Switching
between standard PDOs and APDOs, and re-requesting an APDO to
modify operating voltage/current will be triggered by an
external call into TCPM.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some low-speed and full-speed devices (for example, bluetooth)
do not have time to initialize. For them, ETIMEDOUT is a valid error.
We need to give them another try. Otherwise, they will
never be initialized correctly and in dmesg will be messages
"Bluetooth: hci0 command 0x1002 tx timeout" or similars.
Fixes: 264904ccc3 ("usb: retry reset if a device times out")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Maxim Moseychuk <franchesko.salias.hudro.pedros@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dwc3_ep_dequeue() waits for completion of End Transfer command using
wait_event_lock_irq(), which will release the dwc3->lock while waiting
and reacquire after completion. This allows a potential race condition
with ep_disable() which also removes all requests from started_list
and pending_list.
The check for NULL r->trb should catch this but currently it exits to
the wrong 'out1' label which calls dwc3_gadget_giveback(). Since its
list entry was already removed, if CONFIG_DEBUG_LIST is enabled a
'list_del corruption' bug is thrown since its next/prev pointers are
already LIST_POISON1/2. If r->trb is NULL it should simply exit to
'out0'.
Fixes: cf3113d893 ("usb: dwc3: gadget: properly increment dequeue pointer on ep_dequeue")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fixes the following sparse warning:
drivers/usb/dwc3/gadget.c:169:6: warning:
symbol 'dwc3_gadget_del_and_unmap_request' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix to return error code -ENOMEM from the alloc fail error handling
case instead of 0, as done elsewhere in this function.
Fixes: ecd29dabb2 ("usb: dwc2: pci: Handle error cleanup in probe")
Reviewed-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
By clearing NAK status of EP, core will send ZLP
to IN token and assert NAK interrupt relying
on TxFIFO status only.
The WA applies only to core versions from 2.72a
to 4.00a (including both). Also for FS_IOT_1.00a
and HS_IOT_1.00a.
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
devm_regulator_get_optional returns -ENODEV if the regulator isn't
there, so if that's the case we have to make sure not to leave -ENODEV
in the regulator pointer.
Also, make sure we return 0 in that case, but correctly propagate any
other errors. Also propagate the error from _dwc2_hcd_start.
Fixes: 531ef5ebea ("usb: dwc2: add support for host mode external vbus supply")
Cc: Amelie Delaunay <amelie.delaunay@st.com>
Reviewed-by: Amelie Delaunay <amelie.delaunay@st.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.
Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since commit 39cee200c2 ("usb: musb: core: call init and shutdown for
the usb phy") the musb USB phy is initialised by musb_core, but the
original initialisation in the dsps-glue init callback was left in
place resulting in two calls to phy init during probe (and similarly,
two shutdowns on remove).
Drop the duplicate phy init and shutdown calls from the dsps glue in
favour of the ones in musb core, which other glue drivers rely on.
Note however that any generic phy is still initialised in the glue init
callback (just as for the other drivers).
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the new HCD flag which prevents USB core from trying to manage our
phys.
This is needed to be able to associate the controller platform device
with the glue device device-tree node on the BBB which uses legacy USB
phys. Otherwise, the generic phy lookup in usb_phy_roothub_init() and
thus HCD registration fails repeatedly with -EPROBE_DEFER (see commit
178a0bce05 ("usb: core: hcd: integrate the PHY wrapper into the HCD
core")).
Note that a related phy-lookup issue was recently worked around in the
phy core by commit b7563e2796 ("phy: work around 'phys' references to
usb-nop-xceiv devices"). Something similar may now be needed for other
USB phys, and in particular if we eventually want to let USB core manage
musb generic phys.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1468266 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Improve the kerneldoc for usb_ep_queue() to note explicitly that the
request's completion routine will be called if and only if the return
value is 0. The corresponding fact about usb_submit_urb() for the
host-side API has long been documented, and this has always been the
intention for the gadget API. But until now, documentation seems to
have been lacking.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Tegra's EHCI driver has a build dependency on Tegra's PHY driver and
currently Tegra's PHY driver is built only when Tegra's EHCI driver is
built. Add own Kconfig entry for the Tegra's PHY driver so that drivers
other than ehci-tegra (like ChipIdea UDC) could work with ehci-tegra
driver being disabled in kernels config by allowing user to manually
select the PHY driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UTMI pads are shared by USB controllers and reset of UTMI pads is shared
with the reset of USB1 controller. Currently reset of UTMI pads is done by
the EHCI driver and ChipIdea UDC works because EHCI driver always happen
to be probed first. Move reset controls from ehci-tegra to tegra-phy in
order to resolve the problem.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tegra's PHY driver has a mix of pr_err() and dev_err(), let's switch to
dev_err() and use common errors message formatting across the driver for
consistency.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This clarifies the license of the code. While here also add an include
guard to the header file.
Fixes: 07dbff0ddb ("usb: core: add a wrapper for the USB PHYs on the HCD")
Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add rx_lanes and tx_lanes lane count sysfs entries for a usb device
struct usb_devuce rx_lanes and tx_lanes variables.
Shows number of lanes used by the usb device
Data rate of a device is the lane speed * lane count, for example
USB 3.2 Gen 2x2 device uses 10Gbps signaling per lane, and has dual-lane
support 10Gbps * 2 = 20Gbps
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB 3.2 specification adds a Gen XxY notion for USB3 devices where
X is the signaling rate on the wire. Gen 1xY is 5Gbps Superspeed
and Gen 2xY is 10Gbps SuperSpeedPlus. Y is the lane count.
For normal, non inter-chip (SSIC) devies the rx and tx lane count is
symmetric, and the maximum lane count for USB 3.2 devices is 2 (dual-lane).
SSIC devices may have asymmetric lane counts, with up to four
lanes per direction. The USB 3.2 specification doesn't point out
how to use the Gen XxY notion for these devices, so we limit the Gen Xx2
notion to symmertic Dual lane devies.
For other devices just show Gen1 or Gen2
Gen 1 5Gbps
Gen 2 10Gbps
Gen 1x2 10Gbps Dual-lane (USB 3.2)
Gen 2x2 20Gbps Dual-lane (USB 3.2)
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the the rx_lane and tx_lane count to "2" for USB 3.2 hosts.
For all other older hosts set the default lane counts to 1
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB 3.2 specification adds Dual-lane support, doubling the maximum
SuperSpeedPlus data rate from 10Gbps to 20Gbps.
Dual-lane takes into use a second set of rx and tx wires/pins in the
Type-C cable and connector.
Add "rx_lanes" and "tx_lanes" variables to struct usb_device to store
the numer of lanes in use. Number of lanes can be read using the extended
port status hub request that was introduced in USB 3.1.
Extended port status rx and tx lane count are zero based, maximum
lanes supported by non inter-chip (SSIC) USB 3.2 is 2 (dual lane) with
rx and tx lane count symmetric. SSIC devices support asymmetric lanes
up to 4 lanes per direction.
If extended port status is not available then default to one lane.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hosts that support USB 3.2 Enhaned SuperSpeed can set their hcd speed
to HCD_USB32 to let usb core and host drivers know that the controller
supports new USB 3.2 dual-lane features.
make sure usb core handle HCD_USB32 hosts correctly, for now similar
to HCD_USB32.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Armada 7K/8K we need to explicitly enable the register clock. This
clock is optional because not all the SoCs using this IP need it but at
least for Armada 7K/8K it is actually mandatory.
The change was done at xhci-plat level and not at a xhci-mvebu.c because,
it is expected that other SoC would have this kind of constraint.
The binding documentation is updating accordingly.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
clk_disable_unprepare() already checks that the clock pointer is valid.
No need to test it before calling it.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since there is no user of max_snk_*, so we can remove them from tcpm.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since max_snk_* is to be deprecated, so remove max_snk_* by adding a
variable PDO for sink config.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since max_snk_* is to be deprecated, so remove max_snk_* by adding a
variable PDO for sink config.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is a combination of commit 57e6f0d7b8
("typec: tcpm: Only request matching pdos") and source
pdo selection optimization based on it, instead of only
compare between the same pdo type of sink and source,
we should check source pdo voltage range is within the
voltage range of one sink pdo.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wait_for_connected() wait till a port change status to
USB_PORT_STAT_CONNECTION, but this is not possible if
the port is unpowered. The loop will only exit at timeout.
Such case take place if an over-current incident happen
while system is in S3. Then during resume wait_for_connected()
will wait 2s, which may be noticeable by the user.
Signed-off-by: Dominik Bozek <dominikx.bozek@intel.com>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The legacy interface for associating controllers with phys from board
files and platform code has been unused since commit 9080b8dc76 ("ARM:
OMAP2+: Remove legacy usb-host.c platform init code"). Since then, all
calls to usb_get_phy_dev() and its devres version have been returning
-ENODEV.
Now that the final calls to these functions have been removed, we can
drop this legacy lookup interface altogether.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop support for legacy phys for rcar2 which hasn't been used with a
mainline kernel since commit 9080b8dc76 ("ARM: OMAP2+: Remove legacy
usb-host.c platform init code"). Specifically, since that commit
usb_get_phy_dev() have always returned -ENODEV and consequently this
code has not been used.
Note that the legacy-phy API is still being used in gadget mode to bind
the peripheral controller.
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop support for non-DT systems, which hasn't been used by a mainline
kernel since commit 9080b8dc76 ("ARM: OMAP2+: Remove legacy usb-host.c
platform init code"). Specifically, since that commit usb_get_phy_dev()
have always returned -ENODEV when looking up a legacy phy, something
which in turn would have led to the init callback returning
-EPROBE_DEFER indefinitely.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop support for looking up legacy phys defined by board files,
something which hasn't been used by a mainline kernel since commit
9080b8dc76 ("ARM: OMAP2+: Remove legacy usb-host.c platform init
code"). Specifically, since that commit usb_get_phy_dev() have always
returned -ENODEV and consequently this code has not been used.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop support for looking up and initialising legacy phys in USB core,
something which hasn't been used by a mainline kernel since commit
9080b8dc76 ("ARM: OMAP2+: Remove legacy usb-host.c platform init
code"). Specifically, since that commit usb_get_phy_dev() have always
returned -ENODEV and consequently this code has not been used.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the unused legacy usb_bind_phy() helper whose last user was removed
in 2016 when OMAP moved to device-tree boot (9080b8dc76 ("ARM: OMAP2+:
Remove legacy usb-host.c platform init code")).
Note that this means that for the last couple of years the phy_bind_list
has been empty (when using mainline kernels) and that consequently all
phy lookups using the usb_get_phy_dev() interface have failed with
-ENODEV. This helper along with its current users will be removed by
follow-on patches.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refine probe and disconnect debug msgs to be useful and say what is
in progress.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST".
In most cases this other symbol is an architecture or platform specific
symbol, or PCI.
Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.
This simplifies the dependencies, and allows to improve compile-testing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com> [drivers/usb/gadget/]
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
isp1760_stop() is never called in atomic context.
The call chain ending up at isp1760_stop() is:
[1] isp1760_stop() <- isp1760_shutdown()
isp1760_shutdown() is set as ".shutdown" in struct hc_driver.
isp1760_stop() is also set as ".stop" in hc_driver.
These functions are not called in atomic context.
Despite never getting called from atomic context, isp1760_stop()
calls mdelay() to busily wait.
This is not necessary and can be replaced with msleep() to
avoid busy waiting.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
isp1760_init_core() is never called in atomic context.
The call chains ending up at isp1760_init_core() are:
[1] isp1760_init_core() <- isp1760_register() <- isp1760_plat_probe()
[2] isp1760_init_core() <- isp1760_register() <- isp1761_pci_probe()
isp1760_plat_probe() is set as ".probe" in struct platform_driver.
isp1761_pci_probe() is set as ".probe" in struct pci_driver.
These functions are not called in atomic context.
Despite never getting called from atomic context, isp1761_pci_probe()
calls mdelay() to busily wait.
This is not necessary and can be replaced with msleep() to
avoid busy waiting.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
init_freecom() is never called in atomic context.
init_freecom() is set as ".initFunction" through UNUSUAL_DEV().
And ->initFunction() is only called by usb_stor_acquire_resources(),
which is only called by usb_stor_probe2().
usb_stor_probe2() is called by *_probe() functions (like alauda_probe())
for each USB driver.
*_probe() functions are set ".probe" in struct usb_driver.
These functions are not called in atomic context.
Despite never getting called from atomic context, init_freecom()
calls mdelay() to busily wait.
This is not necessary and can be replaced with msleep() to
avoid busy waiting.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_get_resource() may fail and return NULL, so we should
better check it's return value to avoid a NULL pointer dereference
a bit later in the code.
This is detected by Coccinelle semantic patch.
@@
expression pdev, res, n, t, e, e1, e2;
@@
res = platform_get_resource(pdev, t, n);
+ if (!res)
+ return -EINVAL;
... when != res == NULL
e = devm_ioremap_nocache(e1, res->start, e2);
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use new return type vm_fault_t for the fault handler
in struct vm_operations_struct. For now, this is just
documenting that the function returns a VM_FAULT value
rather than an errno. Once all instances are converted,
vm_fault_t will become a distinct type.
Reference id -> 1c8f422059 ("mm: change return type to
vm_fault_t")
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Reviewed-by: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new axp288 extcon driver has no dependency on USB itself but
calls the usb role switch helper functions. This causes a link error
when USB_COMMON is disabled, as that subdirectory never gets entered:
drivers/extcon/extcon-axp288.o: In function `axp288_usb_role_work':
extcon-axp288.c:(.text+0x47b): undefined reference to `usb_role_switch_set_role'
extcon-axp288.c:(.text+0x498): undefined reference to `usb_role_switch_get_role'
drivers/extcon/extcon-axp288.o: In function `axp288_extcon_probe':
extcon-axp288.c:(.text+0x675): undefined reference to `usb_role_switch_get'
extcon-axp288.c:(.text+0x6d1): undefined reference to `usb_role_switch_put'
drivers/extcon/extcon-axp288.o: In function `axp288_put_role_sw':
extcon-axp288.c:(.text+0x1c): undefined reference to `usb_role_switch_put'
There are multiple ways of fixing this, I chose to 'select USB_COMMON',
since that is how we solved the same problem for other helpers like
USB_LED_TRIG or PHY drivers.
Fixes: d54f063cdb ("extcon: axp288: Set USB role where necessary")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently hcd.c is the only consumer of the usb_phy_roothub logic. This
already includes the required header files so struct device is known.
However, future consumers might not know about struct device.
Add a forward declaration for struct device to fix potential future
consumers which don't include any of the struct device API headers.
Fixes: 07dbff0ddb ("usb: core: add a wrapper for the USB PHYs on the HCD")
Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the generic PHY support is disabled the stub of devm_of_phy_get_by_index
returns ENOSYS. This corner case isn't handled properly by
usb_phy_roothub_add_phy and at least breaks USB support on Raspberry Pi
(bcm2835_defconfig):
dwc2 20980000.usb: dwc2_hcd_init() FAILED, returning -38
dwc2: probe of 20980000.usb failed with error -38
Let usb_phy_roothub_alloc() return in case CONFIG_GENERIC_PHY is
disabled to fix this issue (compilers might even be smart enough to
optimize away most of the code within usb_phy_roothub_alloc and
usb_phy_roothub_add_phy if CONFIG_GENERIC_PHY is disabled). All
existing usb_phy_roothub_* functions are already NULL-safe, so no
special handling is required there.
Fixes: 07dbff0ddb ("usb: core: add a wrapper for the USB PHYs on the HCD")
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the USB controller can wake up the system (which is the case for
example with the Mediatek USB3 IP) then we must not call phy_exit during
suspend to ensure that the USB controller doesn't have to re-enumerate
the devices during resume.
However, if the USB controller cannot wake up the system (which is the
case for example on various TI platforms using a dwc3 controller) then
we must call phy_exit during suspend. Otherwise the PHY driver keeps the
clocks enabled, which prevents the system from reaching the lowest power
levels in the suspend state.
Solve this by introducing two new functions in the PHY wrapper which are
dedicated to the suspend and resume handling.
If the controller can wake up the system the new usb_phy_roothub_suspend
function will simply call usb_phy_roothub_power_off. However, if wake up
is not supported by the controller it will also call
usb_phy_roothub_exit.
The also new usb_phy_roothub_resume function takes care of calling
usb_phy_roothub_init (if the controller can't wake up the system) in
addition to usb_phy_roothub_power_on.
Fixes: 07dbff0ddb ("usb: core: add a wrapper for the USB PHYs on the HCD")
Fixes: 178a0bce05 ("usb: core: hcd: integrate the PHY wrapper into the HCD core")
Reported-by: Roger Quadros <rogerq@ti.com>
Suggested-by: Roger Quadros <rogerq@ti.com>
Suggested-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before this patch usb_phy_roothub_init served two purposes (from a
caller's point of view - like hcd.c):
- parsing the PHYs and allocating the list entries
- calling phy_init on each list entry
While this worked so far it has one disadvantage: if we need to call
phy_init for each PHY instance then the existing code cannot be re-used.
Solve this by splitting off usb_phy_roothub_alloc which only parses the
PHYs and allocates the list entries.
usb_phy_roothub_init then gets a struct usb_phy_roothub and only calls
phy_init on each PHY instance (along with the corresponding cleanup if
that failed somewhere).
This is a preparation step for adding proper suspend support for some
hardware that requires phy_exit to be called during suspend and phy_init
to be called during resume.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_phy_roothub_exit() should return the error code from the phy_exit()
call if exiting the PHY failed.
However, since a wrong variable is used usb_phy_roothub_exit() currently
always returns 0, even if one of the phy_exit calls returned an error.
Clang also reports this bug:
kernel/drivers/usb/core/phy.c:114:8: warning: explicitly assigning value of
variable of type 'int' to itself [-Wself-assign] error, forbidden
warning: phy.c:114
Fix this by assigning the error code from phy_exit() to the "ret"
variable to propagate the error correctly.
Fixes: 07dbff0ddb ("usb: core: add a wrapper for the USB PHYs on the HCD")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some boards, under heavy load, the EC firmware is
unable to complete commands even in one second. Increasing
the command completion timeout value to five seconds.
Reported-by: Quanxian Wang <quanxian.wang@intel.com>
Fixes: c1b0bc2dab ("usb: typec: Add support for UCSI interface")
Cc: <stable@vger.kernel.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit b07c12517f
It is incomplete and causes hangs on devices when shutting down. It
needs a much more "complete" fix in order to work properly. As that fix
has not been merged, revert this patch for now before it causes any more
problems.
Cc: Greg Hackmann <ghackmann@google.com>
Cc: Adam Wallis <awallis@codeaurora.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add DELAY_INIT quirk to fix the following problem with HP
v222w 16GB Mini:
usb 1-3: unable to read config index 0 descriptor/start: -110
usb 1-3: can't read configurations, error -110
usb 1-3: can't set config #1, error -110
Signed-off-by: Kamil Lulko <kamilx.lulko@intel.com>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is the following build error with CONFIG_TYPEC_UCSI=m, CONFIG_FTRACE=y
and CONFIG_TRACING=n:
ERROR: "__tracepoint_ucsi_command" [drivers/usb/typec/ucsi/typec_ucsi.ko] undefined!
ERROR: "__tracepoint_ucsi_register_port" [drivers/usb/typec/ucsi/typec_ucsi.ko] undefined!
ERROR: "__tracepoint_ucsi_notify" [drivers/usb/typec/ucsi/typec_ucsi.ko] undefined!
ERROR: "__tracepoint_ucsi_reset_ppm" [drivers/usb/typec/ucsi/typec_ucsi.ko] undefined!
ERROR: "__tracepoint_ucsi_run_command" [drivers/usb/typec/ucsi/typec_ucsi.ko] undefined!
ERROR: "__tracepoint_ucsi_ack" [drivers/usb/typec/ucsi/typec_ucsi.ko] undefined!
ERROR: "__tracepoint_ucsi_connector_change" [drivers/usb/typec/ucsi/typec_ucsi.ko] undefined!
This compination is quite hard to create because CONFIG_TRACING gets selected
only in rare cases without CONFIG_FTRACE.
The build failure is caused by conditionally compiling trace.c depending on
the wrong option CONFIG_FTRACE. Change this to depend on CONFIG_TRACING like
other users of tracepoints do.
Fixes: c1b0bc2dab ("usb: typec: Add support for UCSI interface")
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix it to not print kernel pointer address. Remove the conditional
and debug message as it isn't very useful.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vhci_hcd fails to do reset to put usb device and sockfd in the
module remove/stop paths. Fix the leak.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On chromebooks we depend on wakeup count to identify the wakeup source.
But currently USB devices do not increment the wakeup count when they
trigger the remote wake. This patch addresses the same.
Resume condition is reported differently on USB 2.0 and USB 3.0 devices.
On USB 2.0 devices, a wake capable device, if wake enabled, drives
resume signal to indicate a remote wake (USB 2.0 spec section 7.1.7.7).
The upstream facing port then sets C_PORT_SUSPEND bit and reports a
port change event (USB 2.0 spec section 11.24.2.7.2.3). Thus if a port
has resumed before driving the resume signal from the host and
C_PORT_SUSPEND is set, then the device attached to the given port might
be the reason for the last system wakeup. Increment the wakeup count for
the same.
On USB 3.0 devices, a function may signal that it wants to exit from device
suspend by sending a Function Wake Device Notification to the host (USB3.0
spec section 8.5.6.4) Thus on receiving the Function Wake, increment the
wakeup count.
Signed-off-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Armada 7K/8K we need to explicitly enable the register clock. This
clock is optional because not all the SoCs using this IP need it but at
least for Armada 7K/8K it is actually mandatory.
The change was done at xhci-plat level and not at a xhci-mvebu.c because,
it is expected that other SoC would have this kind of constraint.
The binding documentation is updating accordingly.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
clk_disable_unprepare() already checks that the clock pointer is valid.
No need to test it before calling it.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Dell Inspiron 5775 is a Raven Ridge. The Enable Slot command timed
out when a USB device gets plugged:
[ 212.156326] xhci_hcd 0000:03:00.3: Error while assigning device slot ID
[ 212.156340] xhci_hcd 0000:03:00.3: Max number of devices this xHCI host supports is 64.
[ 212.156348] usb usb2-port3: couldn't allocate usb_device
AMD suggests that a delay before xHC suspends can fix the issue.
I can confirm it fixes the issue, so use the suspend delay quirk for
Raven Ridge's xHC.
Cc: stable@vger.kernel.org
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arrow USB Blaster integrated on MAX1000 board uses the same vendor ID
(0x0403) and product ID (0x6010) as the "original" FTDI device.
This patch avoids picking up by ftdi_sio of the first interface of this
USB device. After that this device can be used by Arrow user-space JTAG
driver.
Signed-off-by: Vasyl Vavrychuk <vvavrychuk@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Added the USB VID and PID for the USB serial console on some National
Instruments devices.
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Pull general security layer updates from James Morris:
- Convert security hooks from list to hlist, a nice cleanup, saving
about 50% of space, from Sargun Dhillon.
- Only pass the cred, not the secid, to kill_pid_info_as_cred and
security_task_kill (as the secid can be determined from the cred),
from Stephen Smalley.
- Close a potential race in kernel_read_file(), by making the file
unwritable before calling the LSM check (vs after), from Kees Cook.
* 'next-general' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
security: convert security hooks to use hlist
exec: Set file unwritable before LSM check
usb, signal, security: only pass the cred, not the secid, to kill_pid_info_as_cred and security_task_kill
Here is the big set of tty and serial driver patches for 4.17-rc1
Not all that big really, most are just small fixes and additions to
existing drivers. There's a bunch of work on the imx serial driver
recently for some reason, and a new embedded serial driver added as
well.
Full details are in the shortlog.
All of these have been in the linux-next tree for a while with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWsSn+w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynb6wCdEf5dAUrSB37ptZY78n4kc6nI6NAAniDO+rjL
ppZZp7QTIB/bnPfW8cOH
=+tfY
-----END PGP SIGNATURE-----
Merge tag 'tty-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty and serial driver patches for 4.17-rc1
Not all that big really, most are just small fixes and additions to
existing drivers. There's a bunch of work on the imx serial driver
recently for some reason, and a new embedded serial driver added as
well.
Full details are in the shortlog.
All of these have been in the linux-next tree for a while with no
reported issues"
* tag 'tty-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (66 commits)
serial: expose buf_overrun count through proc interface
serial: mvebu-uart: fix tx lost characters
tty: serial: msm_geni_serial: Fix return value check in qcom_geni_serial_probe()
tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP
8250-men-mcb: add support for 16z025 and 16z057
powerpc: Mark the variable earlycon_acpi_spcr_enable maybe_unused
serial: stm32: fix initialization of RS485 mode
ARM: dts: STi: Remove "console=ttyASN" from bootargs for STi boards
vt: change SGR 21 to follow the standards
serdev: Fix typo in serdev_device_alloc
ARM: dts: STi: Fix aliases property name for STi boards
tty: st-asc: Update tty alias
serial: stm32: add support for RS485 hardware control mode
dt-bindings: serial: stm32: add RS485 optional properties
selftests: add devpts selftests
devpts: comment devpts_mntget()
devpts: resolve devpts bind-mounts
devpts: hoist out check for DEVPTS_SUPER_MAGIC
serial: 8250: Add Nuvoton NPCM UART
serial: mxs-auart: disable clks of Alphascale ASM9260
...
Here is the big set of USB and PHY driver patches for 4.17-rc1.
Lots of USB typeC work happened this round, with code moving from the
staging directory into the "real" part of the kernel, as well as new
infrastructure being added to be able to handle the different types of
"roles" that typeC requires.
There is also the normal huge set of USB gadget controller and driver
updates, along with XHCI changes, and a raft of other tiny fixes all
over the USB tree. And the PHY driver updates are merged in here as
well as they interacted with the USB drivers in some places.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWsSpJw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylGawCdED2xS3HUxOIqfh81d8B1py8ji04AoJXdLAsH
JgwXbdbibZBabYTVi5s5
=LrRH
-----END PGP SIGNATURE-----
Merge tag 'usb-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big set of USB and PHY driver patches for 4.17-rc1.
Lots of USB typeC work happened this round, with code moving from the
staging directory into the "real" part of the kernel, as well as new
infrastructure being added to be able to handle the different types of
"roles" that typeC requires.
There is also the normal huge set of USB gadget controller and driver
updates, along with XHCI changes, and a raft of other tiny fixes all
over the USB tree. And the PHY driver updates are merged in here as
well as they interacted with the USB drivers in some places.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (250 commits)
Revert "USB: serial: ftdi_sio: add Id for Physik Instrumente E-870"
usb: musb: gadget: misplaced out of bounds check
usb: chipidea: imx: Fix ULPI on imx53
usb: chipidea: imx: Cleanup ci_hdrc_imx_platform_flag
usb: chipidea: usbmisc: small clean up
usb: chipidea: usbmisc: evdo can be set e/o reset
usb: chipidea: usbmisc: evdo is only specific to OTG port
USB: serial: ftdi_sio: add Id for Physik Instrumente E-870
usb: dwc3: gadget: never call ->complete() from ->ep_queue()
usb: gadget: udc: core: update usb_ep_queue() documentation
usb: host: Remove the deprecated ATH79 USB host config options
usb: roles: Fix return value check in intel_xhci_usb_probe()
USB: gadget: f_midi: fixing a possible double-free in f_midi
usb: core: Add USB_QUIRK_DELAY_CTRL_MSG to usbcore quirks
usb: core: Copy parameter string correctly and remove superfluous null check
USB: announce bcdDevice as well as idVendor, idProduct.
USB:fix USB3 devices behind USB3 hubs not resuming at hibernate thaw
usb: hub: Reduce warning to notice on power loss
USB: serial: ftdi_sio: add support for Harman FirmwareHubEmulator
USB: serial: cp210x: add ELDAT Easywave RX09 id
...
Pull networking updates from David Miller:
1) Support offloading wireless authentication to userspace via
NL80211_CMD_EXTERNAL_AUTH, from Srinivas Dasari.
2) A lot of work on network namespace setup/teardown from Kirill Tkhai.
Setup and cleanup of namespaces now all run asynchronously and thus
performance is significantly increased.
3) Add rx/tx timestamping support to mv88e6xxx driver, from Brandon
Streiff.
4) Support zerocopy on RDS sockets, from Sowmini Varadhan.
5) Use denser instruction encoding in x86 eBPF JIT, from Daniel
Borkmann.
6) Support hw offload of vlan filtering in mvpp2 dreiver, from Maxime
Chevallier.
7) Support grafting of child qdiscs in mlxsw driver, from Nogah
Frankel.
8) Add packet forwarding tests to selftests, from Ido Schimmel.
9) Deal with sub-optimal GSO packets better in BBR congestion control,
from Eric Dumazet.
10) Support 5-tuple hashing in ipv6 multipath routing, from David Ahern.
11) Add path MTU tests to selftests, from Stefano Brivio.
12) Various bits of IPSEC offloading support for mlx5, from Aviad
Yehezkel, Yossi Kuperman, and Saeed Mahameed.
13) Support RSS spreading on ntuple filters in SFC driver, from Edward
Cree.
14) Lots of sockmap work from John Fastabend. Applications can use eBPF
to filter sendmsg and sendpage operations.
15) In-kernel receive TLS support, from Dave Watson.
16) Add XDP support to ixgbevf, this is significant because it should
allow optimized XDP usage in various cloud environments. From Tony
Nguyen.
17) Add new Intel E800 series "ice" ethernet driver, from Anirudh
Venkataramanan et al.
18) IP fragmentation match offload support in nfp driver, from Pieter
Jansen van Vuuren.
19) Support XDP redirect in i40e driver, from Björn Töpel.
20) Add BPF_RAW_TRACEPOINT program type for accessing the arguments of
tracepoints in their raw form, from Alexei Starovoitov.
21) Lots of striding RQ improvements to mlx5 driver with many
performance improvements, from Tariq Toukan.
22) Use rhashtable for inet frag reassembly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1678 commits)
net: mvneta: improve suspend/resume
net: mvneta: split rxq/txq init and txq deinit into SW and HW parts
ipv6: frags: fix /proc/sys/net/ipv6/ip6frag_low_thresh
net: bgmac: Fix endian access in bgmac_dma_tx_ring_free()
net: bgmac: Correctly annotate register space
route: check sysctl_fib_multipath_use_neigh earlier than hash
fix typo in command value in drivers/net/phy/mdio-bitbang.
sky2: Increase D3 delay to sky2 stops working after suspend
net/mlx5e: Set EQE based as default TX interrupt moderation mode
ibmvnic: Disable irqs before exiting reset from closed state
net: sched: do not emit messages while holding spinlock
vlan: also check phy_driver ts_info for vlan's real device
Bluetooth: Mark expected switch fall-throughs
Bluetooth: Set HCI_QUIRK_SIMULTANEOUS_DISCOVERY for BTUSB_QCA_ROME
Bluetooth: btrsi: remove unused including <linux/version.h>
Bluetooth: hci_bcm: Remove DMI quirk for the MINIX Z83-4
sh_eth: kill useless check in __sh_eth_get_regs()
sh_eth: add sh_eth_cpu_data::no_xdfar flag
ipv6: factorize sk_wmem_alloc updates done by __ip6_append_data()
ipv4: factorize sk_wmem_alloc updates done by __ip_append_data()
...
This removes the entire architecture code for blackfin, cris, frv, m32r,
metag, mn10300, score, and tile, including the associated device drivers.
I have been working with the (former) maintainers for each one to ensure
that my interpretation was right and the code is definitely unused in
mainline kernels. Many had fond memories of working on the respective
ports to start with and getting them included in upstream, but also saw
no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company
in charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It seems
that all the SoC product lines are still around, but have not used the
custom CPU architectures for several years at this point. In contrast,
CPU instruction sets that remain popular and have actively maintained
kernel ports tend to all be used across multiple licensees.
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I made
sure that they are all unused. Some architectures (notably tile, mn10300,
and blackfin) are still being shipped in products with old kernels,
but those products will never be updated to newer kernel releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing their
support or getting it added to mainline gcc in the first place.
They all have patched gcc-7.3 ports that work to some degree, but
complete upstream support won't happen before gcc-8.1. Csky posted
their first kernel patch set last week, their situation will be similar.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fQ8z
-----END PGP SIGNATURE-----
Merge tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pul removal of obsolete architecture ports from Arnd Bergmann:
"This removes the entire architecture code for blackfin, cris, frv,
m32r, metag, mn10300, score, and tile, including the associated device
drivers.
I have been working with the (former) maintainers for each one to
ensure that my interpretation was right and the code is definitely
unused in mainline kernels. Many had fond memories of working on the
respective ports to start with and getting them included in upstream,
but also saw no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company in
charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It
seems that all the SoC product lines are still around, but have not
used the custom CPU architectures for several years at this point. In
contrast, CPU instruction sets that remain popular and have actively
maintained kernel ports tend to all be used across multiple licensees.
[ See the new nds32 port merged in the previous commit for the next
generation of "one company in charge of an SoC line, a CPU
microarchitecture and a software ecosystem" - Linus ]
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I
made sure that they are all unused. Some architectures (notably tile,
mn10300, and blackfin) are still being shipped in products with old
kernels, but those products will never be updated to newer kernel
releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing
their support or getting it added to mainline gcc in the first
place. They all have patched gcc-7.3 ports that work to some
degree, but complete upstream support won't happen before gcc-8.1.
Csky posted their first kernel patch set last week, their situation
will be similar
[ Palmer Dabbelt points out that RISC-V support is in mainline gcc
since gcc-7, although gcc-7.3.0 is the recommended minimum - Linus ]"
This really says it all:
2498 files changed, 95 insertions(+), 467668 deletions(-)
* tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (74 commits)
MAINTAINERS: UNICORE32: Change email account
staging: iio: remove iio-trig-bfin-timer driver
tty: hvc: remove tile driver
tty: remove bfin_jtag_comm and hvc_bfin_jtag drivers
serial: remove tile uart driver
serial: remove m32r_sio driver
serial: remove blackfin drivers
serial: remove cris/etrax uart drivers
usb: Remove Blackfin references in USB support
usb: isp1362: remove blackfin arch glue
usb: musb: remove blackfin port
usb: host: remove tilegx platform glue
pwm: remove pwm-bfin driver
i2c: remove bfin-twi driver
spi: remove blackfin related host drivers
watchdog: remove bfin_wdt driver
can: remove bfin_can driver
mmc: remove bfin_sdh driver
input: misc: remove blackfin rotary driver
input: keyboard: remove bf54x driver
...
This reverts commit 79a0b33165.
Turns out this is not an FTDI device after all.
Fixes: 79a0b33165 ("USB: serial: ftdi_sio: add Id for Physik Instrumente E-870")
Reported-by: Martin Teichmann <martin.teichmann@xfel.eu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
musb->endpoints[] has array size MUSB_C_NUM_EPS.
We must check array bounds before accessing the array and not afterwards.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Bin Liu <b-liu@ti.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Traditionally, PORTSC should be set before initializing ULPI phys. But
setting PORTSC before powering on the phy results in a kernel freeze
on imx53 based GE PPD. As a workaround this initializes the phy early
in the imx platform code and disables phy power management from the
core.
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some trivial cleanups, that do not change functionality.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The register write can be done outside the if and else condition
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
evdo bit can be set or reset. We can not trust evdo bit
status after bootloader stage
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB_PHY_CTRL_FUNC is used specific for OTG port as described
in user manual. EVDO need to be set only for index 0 that
correspond to OTG port
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the USB-serial updates for 4.17-rc1, including a
reimplementation of the option-driver interface masking which allows
for a more compact notation when adding new device entries.
Included are also a couple of clean ups and a new ftdi_sio device id.
All but the device-id commit have been in linux-next (without any
reported issues).
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=E3H0
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.17-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.17-rc1
Here are the USB-serial updates for 4.17-rc1, including a
reimplementation of the option-driver interface masking which allows
for a more compact notation when adding new device entries.
Included are also a couple of clean ups and a new ftdi_sio device id.
All but the device-id commit have been in linux-next (without any
reported issues).
Signed-off-by: Johan Hovold <johan@kernel.org>
This adds support for the Physik Instrumente E-870 PIShift Drive
Electronics, a Piezo motor driver.
Signed-off-by: Martin Teichmann <martin.teichmann@xfel.eu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The blackfin architecture is getting removed, and this is the last
remaining architecture specific setting, so the various hacks
can be removed now.
From all I can tell, there are no remaining in-tree users of the
driver, but it could be used by out-of-tree platform ports.
I've marked the driver as 'depends on COMPILE_TEST', short of
removing it outright.
It was originally written for some ARM PXA machines using the same
chip, but that platform never really worked and the code has been
removed a long time ago.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Aaron Wu <aaron.wu@analog.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The blackfin architecture is getting removed, so we can clean up
all the special cases in the musb driver.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Aaron Wu <aaron.wu@analog.com>
Acked-by: Bin Liu <b-liu@ti.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
[arnd: adding in fixups from Aaron and Stephen]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The tile architecture is getting removed, so the ehci and ohci platform
glue drivers are no longer needed. In case of ohci, this is the last
one to define a PLATFORM_DRIVER macro, so we can remove even more.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A lot of Kconfig symbols have architecture specific dependencies.
In those cases that depend on architectures we have already removed,
they can be omitted.
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This is a requirement which has always existed but, somehow, wasn't
reflected in the documentation and problems weren't found until now
when Tuba Yavuz found a possible deadlock happening between dwc3 and
f_hid. She described the situation as follows:
spin_lock_irqsave(&hidg->write_spinlock, flags); // first acquire
/* we our function has been disabled by host */
if (!hidg->req) {
free_ep_req(hidg->in_ep, hidg->req);
goto try_again;
}
[...]
status = usb_ep_queue(hidg->in_ep, hidg->req, GFP_ATOMIC);
=>
[...]
=> usb_gadget_giveback_request
=>
f_hidg_req_complete
=>
spin_lock_irqsave(&hidg->write_spinlock, flags); // second acquire
Note that this happens because dwc3 would call ->complete() on a
failed usb_ep_queue() due to failed Start Transfer command. This is,
anyway, a theoretical situation because dwc3 currently uses "No
Response Update Transfer" command for Bulk and Interrupt endpoints.
It's still good to make this case impossible to happen even if the "No
Reponse Update Transfer" command is changed.
Reported-by: Tuba Yavuz <tuba@ece.ufl.edu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mention that ->complete() should never be called from within
usb_ep_queue().
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The options USB_EHCI_ATH79 and USB_OHCI_ATH79 only enable the
generic EHCI and OHCI platform drivers, and have been marked as
deprecated since 2012.
These can be safely removed if we make sure that USB_EHCI_ROOT_HUB_TT
still get enabled for the EHCI driver. This is now done be selecting
this option when the EHCI platform driver is enabled on the ATH79
platform.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of error, the function devm_ioremap_nocache() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Fixes: f6fb9ec02b ("usb: roles: Add Intel xHCI USB role switch driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It looks like there is a possibility of a double-free vulnerability on an
error path of the f_midi_set_alt function in the f_midi driver. If the
path is feasible then free_ep_req gets called twice:
req->complete = f_midi_complete;
err = usb_ep_queue(midi->out_ep, req, GFP_ATOMIC);
=> ...
usb_gadget_giveback_request
=>
f_midi_complete (CALLBACK)
(inside f_midi_complete, for various cases of status)
free_ep_req(ep, req); // first kfree
if (err) {
ERROR(midi, "%s: couldn't enqueue request: %d\n",
midi->out_ep->name, err);
free_ep_req(midi->out_ep, req); // second kfree
return err;
}
The double-free possibility was introduced with commit ad0d1a058e
("usb: gadget: f_midi: fix leak on failed to enqueue out requests").
Found by MOXCAFE tool.
Signed-off-by: Tuba Yavuz <tuba@ece.ufl.edu>
Fixes: ad0d1a058e ("usb: gadget: f_midi: fix leak on failed to enqueue out requests")
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's a new quirk, USB_QUIRK_DELAY_CTRL_MSG. Add it to usbcore quirks
for completeness.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
strsep() slices string, so the string gets copied by
param_set_copystring() at the end of quirks_param_set() is not the
original value.
Fix that by calling param_set_copystring() earlier.
The null check for val is unnecessary, the caller of quirks_param_set()
does not pass null string.
Remove the superfluous null check. This is found by Smatch.
Fixes: 027bd6cafd ("usb: core: Add "quirks" parameter for usbcore")
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Print bcdDevice which is used by vendors to identify different versions
of the same product (or different versions of firmware).
Adding this to the logs will be useful for support purposes.
Match the %2x.%02x formatting that's used by lsusb -v for this same value.
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fun set of conflict resolutions here...
For the mac80211 stuff, these were fortunately just parallel
adds. Trivially resolved.
In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the
function phy_disable_interrupts() earlier in the file, whilst in
'net-next' the phy_error() call from this function was removed.
In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the
'rt_table_id' member of rtable collided with a bug fix in 'net' that
added a new struct member "rt_mtu_locked" which needs to be copied
over here.
The mlxsw driver conflict consisted of net-next separating
the span code and definitions into separate files, whilst
a 'net' bug fix made some changes to that moved code.
The mlx5 infiniband conflict resolution was quite non-trivial,
the RDMA tree's merge commit was used as a guide here, and
here are their notes:
====================
Due to bug fixes found by the syzkaller bot and taken into the for-rc
branch after development for the 4.17 merge window had already started
being taken into the for-next branch, there were fairly non-trivial
merge issues that would need to be resolved between the for-rc branch
and the for-next branch. This merge resolves those conflicts and
provides a unified base upon which ongoing development for 4.17 can
be based.
Conflicts:
drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f95
(IB/mlx5: Fix cleanup order on unload) added to for-rc and
commit b5ca15ad7e (IB/mlx5: Add proper representors support)
add as part of the devel cycle both needed to modify the
init/de-init functions used by mlx5. To support the new
representors, the new functions added by the cleanup patch
needed to be made non-static, and the init/de-init list
added by the representors patch needed to be modified to
match the init/de-init list changes made by the cleanup
patch.
Updates:
drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function
prototypes added by representors patch to reflect new function
names as changed by cleanup patch
drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init
stage list to match new order from cleanup patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
USB3 hubs don't support global suspend.
USB3 specification 10.10, Enhanced SuperSpeed hubs only support selective
suspend and resume, they do not support global suspend/resume where the
hub downstream facing ports states are not affected.
When system enters hibernation it first enters freeze process where only
the root hub enters suspend, usb_port_suspend() is not called for other
devices, and suspend status flags are not set for them. Other devices are
expected to suspend globally. Some external USB3 hubs will suspend the
downstream facing port at global suspend. These devices won't be resumed
at thaw as the suspend status flag is not set.
A USB3 removable hard disk connected through a USB3 hub that won't resume
at thaw will fail to synchronize SCSI cache, return “cmd cmplt err -71”
error, and needs a 60 seconds timeout which causing system hang for 60s
before the USB host reset the port for the USB3 removable hard disk to
recover.
Fix this by always calling usb_port_suspend() during freeze for USB3
devices.
Signed-off-by: Zhengjun Xing <zhengjun.xing@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we warn the user when the root hub lost power after resume,
but the user cannot do anything about it so it should probably be a
notice.
This will reduce the noise in the console during suspend and resume,
which is already quite significant in many systems.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Quite a lot happened in this cycle, with a total of 95 non-merge
commits. The most interesting parts are listed below:
Synopsys has been adding better support for USB 3.1 to dwc3. The same
series also sets g_mass_storage's max speed to SSP.
Roger Quadros (TI) added support for dual-role using the OTG block
available in some dwc3 implementations, this makes sure that AM437x
can swap roles in runtime.
We have a new SoC supported in dwc3 now - Amlogic Meson GX - thanks to
the work of Martin Blumenstingl.
We also have a ton of changes in dwc2 (51% of all changes, in
fact). The most interesting part there is the support for
Hibernation (a Synopsys PM feature).
Apart from these, we have our regular set of non-critical fixes all
over the place.
-----BEGIN PGP SIGNATURE-----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=F6OC
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-testing
Felipe writes:
usb: changes for v4.17 merge window
Quite a lot happened in this cycle, with a total of 95 non-merge
commits. The most interesting parts are listed below:
Synopsys has been adding better support for USB 3.1 to dwc3. The same
series also sets g_mass_storage's max speed to SSP.
Roger Quadros (TI) added support for dual-role using the OTG block
available in some dwc3 implementations, this makes sure that AM437x
can swap roles in runtime.
We have a new SoC supported in dwc3 now - Amlogic Meson GX - thanks to
the work of Martin Blumenstingl.
We also have a ton of changes in dwc2 (51% of all changes, in
fact). The most interesting part there is the support for
Hibernation (a Synopsys PM feature).
Apart from these, we have our regular set of non-critical fixes all
over the place.
Add device id for Harman FirmwareHubEmulator to make the device
auto-detectable by the driver.
Signed-off-by: Clemens Werther <clemens.werther@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a device ID for the RT Systems cable used to
program Yaesu VX-8R/VX-8DR handheld radios. It uses the main
FTDI VID instead of the common RT Systems VID.
Signed-off-by: Major Hayden <major@mhtx.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some UDC may want to allocate endpoints dynamically, either because
the HW supports an arbitrary large number or because (like the Aspeed
BMC SoCs), the pool of HW endpoints is shared between multiple gadgets.
The allocation side can be done rather easily using the existing
match_ep() UDC hook.
However we have no good place to "free" them.
This implements a "simple" variant of this, which calls an EP dispose
callback on all EPs associated with a gadget when the composite device
gets unbound.
This is required by my upcoming Aspeed vHub driver.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlqvCPYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGOaAH/171cgZGFEXSONxK
3O1AAv61wN5K/ISMt6mnelWR6fZg195FarOx0Rnq7Ot8OWuVa8CGcyT4vX4Z7nb9
SVMQKNMPCVQE4WCDOv6S0njChmRC0BxBoVJtTN9fhywdYgX1KcaTS/drMRHACF5n
rB9eouMQScfMzKGAW08gp5NvEGJ6W1SLX7La3/u0751dYisdJSP7+vFZNxUrGXEA
yIPOQjFu0Tfo8GXz/BwC678RZVzVLN0sE6+/vM7zNnoDlsRVkdDIVMo3UiVqm/NK
B37/TlZz8CYoapoKnRRB5giXnSPDSXtsikbGy3mcy0u5imGe+ZgdjrdYSaLk31cR
NVZY08k=
=pu3X
-----END PGP SIGNATURE-----
Merge tag 'v4.16-rc6' into next-general
Merge to Linux 4.16-rc6 at the request of Jarkko, for his TPM updates.
The phys has already been initialized when add primary hcd,
including usb2 phys and usb3 phys also if exist, so needn't
re-parse "phys" property again.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AB8540 was an evolved version of the AB8500, but it was never
mass produced or put into products, only reference designs exist.
The upstream support was never completed and it is unlikely that
this will happen so drop the support for now to simplify
maintenance of the AB8500.
Cc: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a driver for the Pericom PI3USB30532 Type-C cross switch /
mux chip found on some devices with a Type-C port.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Various Intel SoCs (Cherry Trail, Broxton and others) have an internal USB
role switch for swiching the OTG USB data lines between the xHCI host
controller and the dwc3 gadget controller.
Note on some Cherry Trail systems there is ACPI/AML code listening to
edge interrupts on the id-pin (through an _AIE ACPI method) and switching
the role between ROLE_HOST and ROLE_NONE based on the id-pin. Note it does
not set the role to ROLE_DEVICE, because device-mode is usually not used
under Windows.
The presence of AML code which modifies the cfg0 reg (on some systems)
means that our read/write/modify of cfg0 may race with the AML code
doing the same to avoid this we take the global ACPI lock while doing
the read/write/modify.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xHCI controller on various Intel SoCs has an extended cap mmio-range
which contains registers to control the muxing to the xHCI (host mode)
or the dwc3 (device mode) and vbus-detection for the otg usb-phy.
Having a role-sw driver included in the xHCI code (under drivers/usb/host)
is not desirable. So this commit adds a simple handler for this extended
capability, which creates a platform device with the caps mmio region as
resource, this allows us to write a separate platform role-sw driver for
the role-switch.
Note this commit adds a call to the new xhci_ext_cap_init() function
to xhci_pci_probe(), it is added here because xhci_ext_cap_init() must
be called only once. If in the future we also want to handle ext-caps
on non pci xHCI HCDs from xhci_ext_cap_init() a call to it should also
be added to other bus probe paths.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Modify xhci_find_next_ext_cap(base, offset, id) to return the next
capability offset if 0 is passed for id. Otherwise it will behave as
previously and return the offset of the next capability with matching id
capability id 0 is not used by xHCI (reserved)
This is useful when we want to loop through all capabilities.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the unused (not implemented anywhere) tcpc_mux_dev abstraction
and replace it with calling the new typec_set_orientation,
usb_role_switch_set and typec_set_mode functions.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Setting the mux to MUX_NONE and the switch to USB_SWITCH_DISCONNECT when
the data-role is device is not correct. Plenty of devices support
operating as USB device through a (separate) USB device controller.
We really need 2 different versions of USB_SWITCH_CONNECT,
USB_SWITCH_CONNECT_HOST and USB_SWITCH_DEVICE. Rather then modifying the
tcpc_usb_switch enum for this, simply remove it and switch to the
usb_role enum which provides exactly this, this will save use needing to
convert betweent the 2 enums when calling an usb-role-switch driver later.
Besides switching to the usb_role type, this commit also actually sets the
mux to TYPEC_MUX_USB and the switch to USB_ROLE_DEVICE instead of setting
both to none when the data-role is device.
This commit also makes tcpm_reset_port() call tcpm_mux_set(port,
TYPEC_MUX_NONE, USB_ROLE_NONE) so that the mux and switch
do _not_ stay in their last mode after a detach.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB Type-C specification v1.2 separated the power and data
roles more clearly. Dual-Role-Data term was introduced, and
the meaning of DRP was changed from "Dual-Role-Port" to
"Dual-Role-Power".
In order to allow the port drivers to describe the
capabilities of the ports more clearly according to the
newest specifications, introducing separate definitions for
the data roles.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB role switch is a device that can be used to choose the
data role for USB connector. With dual-role capable USB
controllers, the controller itself will be the switch, but
on some platforms the USB host and device controllers are
separate IPs and there is a mux between them and the
connector. On those platforms the mux driver will need to
register the switch.
With USB Type-C connectors, the host-to-device relationship
is negotiated over the Configuration Channel (CC). That
means the USB Type-C drivers need to be in control of the
role switch. The class provides a simple API for the USB
Type-C drivers for the control.
For other types of USB connectors (mainly microAB) the class
provides user space control via sysfs attribute file that
can be used to request role swapping from the switch.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB Type-C connectors consist of various muxes and switches
that route the pins on the connector to the right locations.
The USB Type-C drivers need to be able to control the muxes,
as they are the ones that know things like the cable plug
orientation, and the current mode that was negotiated with
the partner.
This introduces a small API for registering and controlling
cable plug orientation switches, and separate small API for
registering and controlling pin multiplexer/demultiplexer
switches that are needed with Accessory/Alternate Modes.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For some userspace applications information on the number of
over-current conditions at specific USB hub ports is relevant.
In our case we have a series of USB hardware (using the cp210x driver)
which communicates using a proprietary protocol. These devices sometimes
trigger an over-current situation on some hubs. In case of such an
over-current situation the USB devices offer an interface for reducing
the max used power. As these conditions are quite rare and imply
performance reductions of the device we don't want to reduce the max
power always.
Therefore give user-space applications the possibility to react
adequately by introducing an over_current_counter in the usb port struct
which is exported via sysfs.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AB8540 was an evolved version of the AB8500, but it was never
mass produced or put into products, only reference designs exist.
The upstream support was never completed and it is unlikely that
this will happen so drop the support for now to simplify
maintenance of the AB8500.
Cc: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
On TI's AM437x, the DWC3 controller looses state after a
system suspend/resume. We are re-initializing the controller
but we miss restoring the PRTCAP register. This causes
USB host to break on AM437x after a system suspend/resume.
Fix this by restoring the PRTCAP register on system resume.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
DWC_usb3 speed can only be set up to SuperSpeed. Limit the setting to
SuperSpeed only should the value be higher. Otherwise, the controller
will read an invalid speed value and set the device to an incorrect
speed.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Check and configure TX/RX threshold for DWC_usb31. Update dwc3 structure
with new fields to store these threshold configurations.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
DWC_usb31 controller has a different UsbRxPktCnt bit fields from
GRXTHRCFG register. Check for DWC_usb31 IP revision to read the
appropriate value.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
DWC_usb31 controller has different GTXFIFOSIZE bit field for TXFDEF.
Check for DWC_usb31 IP revision to read the appropriate bit fields.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Update two GTXFIFOSIZ bit fields for the DWC_usb31 controller. TXFDEP
is a 15-bit value instead of 16-bit value, and bit 15 is TXFRAMNUM.
The GTXFIFOSIZ register for DWC_usb31 is as follows:
+-------+-----------+----------------------------------+
| BITS | Name | Description |
+=======+===========+==================================+
| 31:16 | TXFSTADDR | Transmit FIFOn RAM Start Address |
| 15 | TXFRAMNUM | Asynchronous/Periodic TXFIFO |
| 14:0 | TXFDEP | TXFIFO Depth |
+-------+-----------+----------------------------------+
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
From DWC_usb31 programming guide section 1.3.2, once DWC3_DCTL_CSFTRST
bit is cleared, we must wait at least 50ms before accessing the PHY
domain (synchronization delay).
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Platform device is allocated before adding resources. Make sure to
properly cleanup on error case.
Cc: <stable@vger.kernel.org>
Fixes: f1c7e71081 ("usb: dwc3: convert to pcim_enable_device()")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If building a kernel without FTRACE but with TRACING, dwc3.ko fails to
link due to missing trace events. Fix this by using the correct
Kconfig symbol on Makefile.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Reporting two more VID/PID pairs that work with this driver, having used
an informational webpage <http://reboots.g-cipher.net/lcd/> as a buying
guide now. The page listed additional working VID/PID pairs but did not
include these two. None were upstreamed. Also taking this opportunity to
sort the pairs numerically.
Of the two such cables now in my possession, one is white, bearing the
In-System Design ISD-103 label on one side, sold as an Epson CAEUL0002
"USB to Parallel Smart Cable For Apple Macintosh Computers" (04b8:0002),
and the other is black, bearing the In-System Design ISD-101 label on one
side, sold as an early Belkin F5U002 (05ab:0002).
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trying quirks in usbcore needs to rebuild the driver or the entire
kernel if it's builtin. It can save a lot of time if usbcore has similar
ability like "usbhid.quirks=" and "usb-storage.quirks=".
Rename the original quirk detection function to "static" as we introduce
this new "dynamic" function.
Now users can use "usbcore.quirks=" as short term workaround before the
next kernel release. Also, the quirk parameter can XOR the builtin
quirks for debugging purpose.
This is inspired by usbhid and usb-storage.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The maximum bytes per interval for USB SuperSpeed Plus can be set by
isoc endpoint companion descriptor when it is above 48K. If the
descriptor is provided, then use its value.
USB 3.1 spec 9.6.8
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the USB class define rather than a magic number when refusing to
bind to mass-storage interfaces.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop redundant interface-class test for Samsung GT-B3730 modems for
which we only match and probe the CDC data interface.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reimplement interface masking using device flags stored directly in the
device-id table. This will make it easier to add and maintain device-id
entries by using a more compact and readable notation compared to the
current implementation (which manages pairs of masks in separate
blacklist structs).
Two convenience macros are used to flag an interface as either reserved
or as not supporting modem-control requests:
{ USB_DEVICE(TELIT_VENDOR_ID, TELIT_PRODUCT_ME910_DUAL_MODEM),
.driver_info = NCTRL(0) | RSVD(3) },
For now, we limit the highest maskable interface number to seven, which
allows for (up to 16) additional device flags to be added later should
need arise.
Note that this will likely need to be backported to stable in order to
make future device-id backports more manageable.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
In
dwc3_request *r = NULL;
r = A;
the first assignment has no effect. Remove it.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In preparation to enabling -Wvla, remove VLA and replace it
with dynamic memory allocation instead.
The use of stack Variable Length Arrays needs to be avoided, as they
can be a vector for stack exhaustion, which can be both a runtime bug
or a security flaw. Also, in general, as code evolves it is easy to
lose track of how big a VLA can get. Thus, we can end up having runtime
failures that are hard to debug.
Also, fixed as part of the directive to remove all VLAs from
the kernel: https://lkml.org/lkml/2018/3/7/621
Notice that in this particular case, an alternative to kzalloc is kcalloc,
in which case the code would look as follows instead:
iv = kcalloc(crypto_skcipher_ivsize(tfm_cbc), sizeof(*iv), GFP_KERNEL);
but if the data type of _iv_ never changes, or the type size is always one
byte, kzalloc is good enough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci driver displays the supported xHC USB revision in a message during
driver load:
"Host supports USB 3.1 Enhanced SuperSpeed"
Get the USB minor revision number from the xhci protocol capability.
This will show the correct supported revisions for new USB 3.2 and later
hosts
Don't rely on the SBRN (serial bus revision number) register, it's often
showing 0x30 (USB3.0) for hosts that support USB 3.1
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some devices use a clear endpoint halt request as a soft reset, even if
the endpoint is not halted. This will clear the toggle and sequence on the
device side.
xHCI however refuses to reset a non-halted endpoint, so instead
we need to issue a configure endpoint command on xHCI to clear its host
side toggle and sequence, and get it in sync with the device side.
This is a respin of a old patch that was reverted as it had a stale
endpoint context dequeue value which caused regression.
commit 27082e2654 ("xhci: Clear the host side toggle manually when
endpoint is 'soft reset'")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
make the local ep_state variable a pointer to the actual ring ep_state.
This allows us to read fresh ep_state values every time, will be useful
later.
Also move the streams check out from bulk only case. Even if only
bulk tranfers can use streams we shouldn't continue if those flags
are set. Main reason for this change is really code readability and
grouping functionality
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The default stop endpoint completion handler will give back cancelled
URBs, and clean, or move past those canceller TRBs on the ring.
This is not always the preferred action.
If the stop endpoint command issuer is waiting for a completion
skip the default handler and just call the completion.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
set udev->slot_id to zero when disabling and freeing the xhci slot.
Prevents usb core from calling xhci with a stale slot id.
xHC controller may be reset during resume to recover from some error.
All slots are unusable as they are disabled and freed.
xhci driver starts slot enumeration again from 1 in the order they are
enabled. In the worst case a stale udev->slot_id for one device matches
a newly enabled slot_id for a different device, causing us to
perform a action on the wrong device.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_port_register_device() returns error pointers on error, never NULL.
The IS_ERR_OR_NULL() function returns either 1 or 0 so it means we
return 1 on error instead of a proper error code. The caller only
checks for zero vs non-zero so this doesn't affect runtime.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
skb_copy_expand without __GFP_NOWARN already does a dump_stack
on OOM so these messages are redundant.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in dev_warn warning message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This fixes an oops on unbind / module unload (on the musb omap2430
platform).
musb_remove function now calls musb_platform_exit before disabling
runtime pm.
Signed-off-by: Merlijn Wajer <merlijn@wizzup.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the following test we get stuck by sleeping forever in _dwc3_set_mode()
after which dual-role switching doesn't work.
On dra7-evm's dual-role port,
- Load g_zero gadget driver and enumerate to host
- suspend to mem
- disconnect USB cable to host and connect otg cable with Pen drive in it.
- resume system
- we sleep indefinitely in _dwc3_set_mode due to.
dwc3_gadget_exit()->usb_del_gadget_udc()->udc_stop()->
dwc3_gadget_stop()->wait_event_lock_irq()
To fix this instead of waiting indefinitely with wait_event_lock_irq()
we use wait_event_interruptible_lock_irq_timeout() and print
and error message if there was a timeout.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Declared dwc2_force_mode() function as static, because it was used
only in core.c file, for fixing sparse error.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds a way to enable an external vbus supply in host mode,
when dwc2 drvvbus signal is not used.
This patch is very similar to the one done in U-Boot dwc2 driver [1]. It
also adds dynamic vbus supply management depending on the role and state
of the core.
[1] https://lists.denx.de/pipermail/u-boot/2017-March/283434.html
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If the dr_mode is USB_DR_MODE_OTG, forcing the mode is needed during
driver probe to get the host and device specific HW parameters. Then we
clear the force mode bits so that the core operates in OTG mode.
The force mode bits should not be touched at any other time during the
driver lifetime and they should be preserved whenever the GUSBCFG
register is written to. The force mode bit values will persist across
soft resets of the core.
If the dr_mode is either USB_DR_MODE_HOST or USB_DR_MODE_PERIPHERAL, the
force mode is set just once at probe to configure the core as either a
host or peripheral.
Given the above, we no longer need any other reset delays, force delays,
or any forced modes anywhere else in the driver. So replace all calls to
dwc2_core_reset_and_force_dr_mode() with dwc2_core_reset() and remove
all other unnecessary delays.
Also remove the dwc2_force_mode_if_needed() function since the "if
needed" part is already taken care of by the polling in
dwc2_force_mode().
Finally, remove all other calls to dwc2_clear_force_mode().
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Enable the power down option based on the core capability.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The GPWRDN interrupts are those that occur in both Host and
Device mode while core is in hibernated state.
Export dwc2_core_init to be able to use it in GPWRDN_IDSTS
interrupt handler.
Here we have duplicated init functions in host and gadget sides
so I have left things as it was(used corresponing functions for
host and gadget), maybe in the future we'll resolve this problem
and will use dwc2_core_init for both sides.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Do changes to allow entering hibernated state from USB_SUSPEND
interrupt. All code is added under if conditions and mustn't impact
existing functionality.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
These are wrapper functions which are calling device or host
enter/exit hibernation functions.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add host/device hibernation functions which must be wrapped
by core's dwc2_enter_hibernation()/dwc2_exit_hibernation()
functions.
Make dwc2_backup_global_registers dwc2_restore_global_register
non-static to use them in both host/gadget sides.
Added function names:
dwc2_gadget_enter_hibernation()
dwc2_gadget_exit_hibernation()
dwc2_host_enter_hibernation()
dwc2_host_exit_hibernation()
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add common (host/device) helper functions, which will be called while
exiting from hibernation, from both sides.
dwc2_restore_essential_regs()
dwc2_hib_restore_common()
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Move hptxfsiz to host register's backup/restore functions, not
needed to have it in global register's backup/restore functions.
Add backup for glpmcfg, and read/write for gi2cctl and pcgcctl.
As requires programming guide.
Affected functions:
dwc2_backup_host_registers()
dwc2_restore_host_registers()
dwc2_backup_global_registers()
dwc2_restore_global_registers()
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It will be set once corresponding set_feature command comes.
True if device is allowed to wake-up host by remote-wakeup
signalling.
This is preparation for remote wake-up support implementation,
it will not be implemented until gadget stack provide interface
for bringing remote wake-up signalling.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added a flag to indicate that core is in hibernation,
it is used to determine the hibernation state of the core.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add parameter remote_wakeup to dwc2_restore_device_registers()
to be able to restore device registers according to programming
guide for dwc-otg. It says that in case of rem_wakeup DCTL must not
be restored here.
Remove setting of DCTL_PWRONPRGDONE from this function, because it
will be done in function responsible for exiting from hibernation.
WA for enabled EPx's IN and OUT in DDMA mode. On entering to
hibernation wrong value read and saved from DIEPDMAx,
as result BNA interrupt asserted on hibernation exit
by restoring from saved area.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Moved dtxfsiz from dwc2_gregs_backup to dwc2_dregs_backup,
because it is device register.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add parameter and it's initialization, needed for hibernation.
Reimplement dwc2_set_param_power_down() to support hibernation too.
Now 'power_down' parameter can be initialized with 0, 1 or 2.
0 - No
1 - Partial power down
2 - Hibernation
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
No-op change, only rename.
This code was misnamed originally. It was only responsible for partial
power down and not for hibernation.
Rename core_params->hibernation to core_params->power_down,
dwc2_set_param_hibernation() to dwc2_set_param_power_down().
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Set 'lpm_capable' flag in the gadget structure so
indicating that LPM is supported.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This is useful on platforms (e.g. TI AM437x) that don't
have ID available on a GPIO but do have the OTG block.
We can obtain the ID state via the OTG block and use it
for dual-role switching.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This fixes "utmi_phy_clk_enable: timeout waiting for phy to stabilize"
error message.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The nop_reset and shutdown methods are called in a context that can sleep,
so use gpiod_set_value_cansleep instead of gpiod_set_value.
If you've connected the reset line to a GPIO expander, you'd get a kernel
"slowpath" warning with gpiod_set_value.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The show() method should use scnprintf() not snprintf() because snprintf()
may returns a value that exceeds its second argument.
Signed-off-by: Jaejoong Kim <climbbb.kim@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We don't support PRTCAP == OTG yet, so prevent user from
setting it via debugfs.
Fixes: 41ce1456e1 ("usb: dwc3: core: make dwc3_set_mode() work properly")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Amlogic Meson GXL and AXG SoCs come with a (host-only) dwc3 USB
controller. To use this controller a clock has to be enabled and a reset
line has to be pulsed.
Enabling the clock works identical to other SoCs. However, the reset
line has to be pulsed (using reset_control_reset) instead of using a
level reset (reset_control_{assert,deassert}).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some SoCs (such as Amlogic Meson GXL for example) share the reset line
with other components (in case of the Meson GXL example there's a shared
reset line between the USB2 PHYs, USB3 PHYs and the dwc3 controller).
Additionally SoC implementations may prefer a reset pulse over level
resets.
For now this falls back to the old defaults, which are:
- reset lines are exclusive
- level resets are being used
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Assign true or false to boolean variables instead of an integer value.
This issue was detected with the help of Coccinelle.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added core state checking in dwc2_hsotg_ep_queue() function
to make sure that application will submit requests only in L0 state.
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added call_gadget() function call when entering to L1 state
to inform gadget that core is in L1 state.
Did the same thing when exiting from L1 state
to inform gadget that core is in L0 state.
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Configure core in device mode to support LPM according to
programming guide.
Device will start giving valid responses for LPM tokens.
After this patch device side LPM will start working.
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This interrupt indicates that an LPM transaction
was received on the USB bus. After getting this
interrupt we are going from L0 state to L1 state.
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a function which will be called if device is in L1 sleep state
and Resume/Remote Wakeup Detected interrupt is asserted.
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add lpm, lpm_clock_gating, besl, hird_threshold_en and hird_threshold
core parameters. These will indicate LPM and LPM Errata support
as well as chosen L1 sleeping mode for the core and PHY.
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Make field names of GLPMCFG register in definitions to be
the same with the databook.
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Backup PCGCCTL1 register when entering hibernation mode and
restore it after exiting from hibernation, to keep active ACG
feature.
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added function for supporting Active Clock Gating functionality
in the driver.
PCGCCTL1 (Power and Clock Control) register will be used
for controlling the core`s active clock gating feature, and
the previously reserved 12th bit in GHWCFG4 now indicates that the
controller supports the Dynamic Power Reduction (Active Clock Gating)
during no traffic scenarios such as L0, idle, resume and suspend
states.
dwc2_enable_acg() function sets GATEEN bit in PCGCCTL1 register
and enables ACG, if it supported.
According to ACG functional specification, enabling of ACG feature
in host mode done in host initialization, before turning Vbus on,
specifically in dwc2_core_host_init function.
Enabling of ACG feature in device mode done in device initialization,
before clearing the SftDiscon bit in DCTL.
This bit was cleared in dwc2_hsotg_core_connect() function.So
dwc2_enable_acg() called before dwc2_core_connect() calls.
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We better print an error in case probing of dwc2 fails on
setting the DMA coherent mask.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use GPIO descriptors instead of relying on the old method.
Include irq.h header since it is needed and was indirectly
included through of_gpio.h.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
With the removal of AVR platforms, code related to platform stuff
is useless.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The maximum value that unsigned char can hold is 255, meanwhile
the maximum value of interval is 2^(bIntervalMax-1)=2^15.
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The probe function doesn't properly handle errors. Fix it so that it
properly handles cleanup.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
After platform_device_add(), if we error out, we must do
platform_device_unregister(), which also does the put. So lets move
devm_kzalloc() to simplify error handling and avoid calling of
platform_device_unregister().
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Move usb_phy_generic_register() function call to the top, to simplify
error handling. If this fails we can simply return instead of cleaning
up.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use devm_kzalloc() and remove the unnecessary kfree().
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Before flushing fifos required to check AHB master state and
lush when AHB master is in IDLE state.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added missing GUSBCFG programming in host mode, which fixes
transaction errors issue on HiKey and Altera Cyclone V boards.
These field even if was programmed in device mode (in function
dwc2_hsotg_core_init_disconnected()) will be resetting to POR values
after core soft reset applied.
So, each time when switching to host mode required to set this field
to correct value.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
According databook in Buffer and External DMA mode
non-split periodic channels can't be halted.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Removed unnecessary debug prints about DMA mode for host side
from dwc2_gahbcfg_init() function.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Deleted dwc2_hcd_dump_frrem() function, because it used undefined
parameters from dwc2_hsotg structure. The function body was in #ifdef
statement and was never compiled.
Also removed that parameters from dwc2_hsotg structure, which were
used only in dwc2_hcd_dump_frrem() function.
And also delete dwc2_sample_frrem macro, because without
dwc2_hcd_dump_frrem() function it's lose its purpose.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Renamed __orr32 and __bic32 function names to more descriptive
dwc2_set_bit and dwc2_clear_bit respectively.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Disabled only unmasked endpoints based on DAINTMSK register.
This will allow to minimize GINTSTS_GOUTNAKEFF interrupt handling.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In 'for' loop skipped masked and non-ISOC EPs. Also breaked 'for' loop
after setting SGOUTNAK in DCTL,when one enabled EP was detected.
This will allow to minimize incomplete ISOC OUT interrupt handling.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Disabled only that ISOC endpoints,for which interrupt bit was set
in the DAINTMSK register. This will allow to minimize incomplete
ISOC IN interrupt handling.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Changed AHB burst size from INCR4 to INCR by default.
With this value driver shows excellent DMA performance.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In dwc2_hsotg_core_init_disconnected() function used AHB burst size
parameter, instead of calculating already calculated value.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Move dwc2_hsotg_wait_bit_set function to core.c so it can be used
anywhere in the code.
Added dwc2_hsotg_wait_bit_clear function in core.c.
Replace all the parts of register bit polling code with
dwc2_hsotg_wait_bit_set or dwc2_hsotg_wait_bit_clear functions
calls depends on code logic.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Only check the ID portion of the GSNPSID register and don’t check
the version. This will allow the driver to work with version 4.00a
and later of the DWC_hsotg IP.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some UDC drivers (like the DWC3) expect that the response to a setup()
request is queued from within the setup function itself so that it is
available as soon as setup() has completed.
Upon receiving a setup request the function fs driver creates an event that
is made available to userspace. And only once userspace has acknowledged
that event the response to the setup request is queued.
So it violates the requirement of those UDC drivers and random failures can
be observed. This is basically a race condition and if userspace is able to
read the event and queue the response fast enough all is good. But if it is
not, for example because other processes are currently scheduled to run,
the USB host that sent the setup request will observe an error.
To avoid this the gadget framework provides the USB_GADGET_DELAYED_STATUS
return code. If a setup() callback returns this value the UDC driver is
aware that response is not yet available and can uses the appropriate
methods to handle this case.
Since in the case of function fs the response will never be available when
the setup() function returns make sure that this status code is used.
This fixed random occasional failures that were previously observed on a
DWC3 based system under high system load.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When using a AIO read() operation on the function FS gadget driver a URB is
submitted asynchronously and on URB completion the received data is copied
to the userspace buffer associated with the read operation.
This is done from a kernel worker thread invoking copy_to_user() (through
copy_to_iter()). And while the user space process memory is made available
to the kernel thread using use_mm(), some architecture require in addition
to this that the operation runs with USER_DS set. Otherwise the userspace
memory access will fail.
For example on ARM64 with Privileged Access Never (PAN) and User Access
Override (UAO) enabled the following crash occurs.
Internal error: Accessing user space memory with fs=KERNEL_DS: 9600004f [#1] SMP
Modules linked in:
CPU: 2 PID: 1636 Comm: kworker/2:1 Not tainted 4.9.0-04081-g8ab2dfb-dirty #487
Hardware name: ZynqMP ZCU102 Rev1.0 (DT)
Workqueue: events ffs_user_copy_worker
task: ffffffc87afc8080 task.stack: ffffffc87a00c000
PC is at __arch_copy_to_user+0x190/0x220
LR is at copy_to_iter+0x78/0x3c8
[...]
[<ffffff800847b790>] __arch_copy_to_user+0x190/0x220
[<ffffff80086f25d8>] ffs_user_copy_worker+0x70/0x130
[<ffffff80080b8c64>] process_one_work+0x1dc/0x460
[<ffffff80080b8f38>] worker_thread+0x50/0x4b0
[<ffffff80080bf5a0>] kthread+0xd8/0xf0
[<ffffff8008083680>] ret_from_fork+0x10/0x50
Address this by placing a set_fs(USER_DS) before of the copy operation
and revert it again once the copy operation has finished.
This patch is analogous to commit d7ffde35e3 ("vhost: use USER_DS in
vhost_worker thread") which addresses the same underlying issue.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Increase max_speed of the mass_storage driver for UDCs that support
SuperSpeed Plus. The composite driver will pass this value to UDC core
to set the device speed on probe (actual speed may be different
depending on whether the USB controller supports it or other external
factors).
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Do not log an error if tcpm_register_port() fails with -EPROBE_DEFER.
Fixes: cf140a3569 ("typec: fusb302: Use dev_err during probe")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the driver attempts to spin lock on udc->lock before a NULL
pointer check is performed on udc, hence there is a potential null
pointer dereference on udc->lock. Fix this by moving the null check
on udc before the lock occurs.
Fixes: ea6873a45a ("usbip: vudc: Add SysFS infrastructure for VUDC")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trying quirks in usbcore needs to rebuild the driver or the entire
kernel if it's builtin. It can save a lot of time if usbcore has similar
ability like "usbhid.quirks=" and "usb-storage.quirks=".
Rename the original quirk detection function to "static" as we introduce
this new "dynamic" function.
Now users can use "usbcore.quirks=" as short term workaround before the
next kernel release. Also, the quirk parameter can XOR the builtin
quirks for debugging purpose.
This is inspired by usbhid and usb-storage.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to allow the USB Type-C Class driver take care of
things like muxes and other possible dependencies for the
port drivers, returning ERR_PTR instead of NULL from the
registration functions in case of failure.
The reason for taking over control of the muxes for example
is because handling them in the port drivers would be just
boilerplate.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the new PHY wrapper in place we can now handle multiple PHYs.
Remove the code which handles only one generic PHY as this is now
covered (with support for multiple PHYs as well as suspend/resume
support) by the new PHY wrapper.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.con>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new PHY wrapper is now wired up in the core HCD code. This means
that PHYs are now controlled (initialized, enabled, disabled, exited)
without requiring any host-driver specific code.
Remove the custom USB PHY handling from the ohci-platform driver as the
core HCD code now handles this.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Neil Armstrong <narmstrong@baylibre.con>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new PHY wrapper is now wired up in the core HCD code. This means
that PHYs are now controlled (initialized, enabled, disabled, exited)
without requiring any host-driver specific code.
Remove the custom USB PHY handling from the ehci-platform driver as the
core HCD code now handles this.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Neil Armstrong <narmstrong@baylibre.con>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new PHY wrapper is now wired up in the core HCD code. This means
that PHYs are now controlled (initialized, enabled, disabled, exited)
without requiring any host-driver specific code.
Remove the custom USB PHY handling from the xhci-mtk driver as the core
HCD code now handles this.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This integrates the PHY wrapper into the core hcd infrastructure.
Multiple PHYs which are part of the HCD's device tree node are now
managed (= powered on/off when needed), by the new usb_phy_roothub code.
Suspend and resume is also supported, however not for
runtime/auto-suspend (which is triggered for example when no devices are
connected to the USB bus). This is needed on some SoCs (for example
Amlogic Meson GXL) because if the PHYs are disabled during auto-suspend
then devices which are plugged in afterwards are not seen by the host.
One example where this is required is the Amlogic GXL and GXM SoCs:
They are using a dwc3 USB controller with up to three ports enabled on
the internal roothub. Each port has it's own PHY which must be enabled
(if one of the PHYs is left disabled then none of the USB ports works at
all).
The new logic works on the Amlogic GXL and GXM SoCs because the dwc3
driver internally creates a xhci-hcd which then registers a HCD which
then triggers our new PHY wrapper.
USB controller drivers can opt out of this by setting
"skip_phy_initialization" in struct usb_hcd to true. This is identical
to how it works for a single USB PHY, so the "multiple PHY" handling is
disabled for drivers that opted out of the management logic of a single
PHY.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Tested-by: Yixun Lan <yixun.lan@amlogic.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.con>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many SoC platforms have separate devices for the USB PHY which are
registered through the generic PHY framework. These PHYs have to be
enabled to make the USB controller actually work. They also have to be
disabled again on shutdown/suspend.
Currently (at least) the following HCI platform drivers are using custom
code to obtain all PHYs via devicetree for the roothub/controller and
disable/enable them when required:
- ehci-platform.c has ehci_platform_power_{on,off}
- xhci-mtk.c has xhci_mtk_phy_{init,exit,power_on,power_off}
- ohci-platform.c has ohci_platform_power_{on,off}
With this new wrapper the USB PHYs can be specified directly in the
USB controller's devicetree node (just like on the drivers listed
above). This allows SoCs like the Amlogic Meson GXL family to operate
correctly once this is wired up correctly. These SoCs use a dwc3
controller and require all USB PHYs to be initialized (if one of the USB
PHYs it not initialized then none of USB port works at all).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Yixun Lan <yixun.lan@amlogic.com>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.con>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB HCD core driver parses the device-tree node for "phys" and
"usb-phys" properties. It also manages the power state of these PHYs
automatically.
However, drivers may opt-out of this behavior by setting "phy" or
"usb_phy" in struct usb_hcd to a non-null value. An example where this
is required is the "Qualcomm USB2 controller", implemented by the
chipidea driver. The hardware requires that the PHY is only powered on
after the "reset completed" event from the controller is received.
A follow-up patch will allow the USB HCD core driver to manage more than
one PHY. Add a new "skip_phy_initialization" bitflag to struct usb_hcd
so drivers can opt-out of any PHY management provided by the USB HCD
core driver.
This also updates the existing drivers so they use the new flag if they
want to opt out of the PHY management provided by the USB HCD core
driver. This means that for these drivers the new "multiple PHY"
handling (which will be added in a follow-up patch) will be disabled as
well.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Peter Chen <peter.chen@nxp.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.con>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use kasprintf instead of combination of kmalloc and sprintf and
therefore avoid unnecessary computation of string length.
Also, remove the useless local variable.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ACPI spec inserts sections for new features frequently and section
numbers are changed. It is easy to refer to ACPI spec if ACPI version
is available in comments.
There are no functional changes.
Signed-off-by: Alex Hung <alex.hung@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disabing Latency Tolerance Messaging before port reset is unnecessary.
LTM is automatically disabled at port reset.
If host can't communicate with the device the LTM message will fail, and
the hub driver will unnecessarily do a logical disconnect.
Broken communication is ofter the reason for a reset in the first place.
Additionally we can't guarantee device is in a configured state,
epecially in reset-resume case when root hub lost power.
LTM can't be modified unless device is in a configured state.
Just remove LTM disabling before port reset.
Details about LTM and port reset in USB 3 specification:
USB 3 spec section 9.4.5
"The LTM Enable field can be modified by the SetFeature() and
ClearFeature() requests using the LTM_ENABLE feature selector.
This field is reset to zero when the device is reset."
USB 3 spec section 9.4.1
"The device shall process a Clear Feature (U1_Enable or U2_Enable or
LTM_Enable) only if the device is in the configured state."
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add waiting for an URB transmit finish that let the last URB to be sent
(to be not discarded) during 'release' procedure. W/o this waiting,the
last frame will be nearly always lost.
A test case: an attempt of sending a single frame:
echo -en "\001mk255" >/dev/adutux0
Signed-off-by: Kirill Kapranov <kirill.kirillovich.kapranov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Cc: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Cc: John Youn <johnyoun@synopsys.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Cc: Peter Chen <Peter.Chen@nxp.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pointer dev is initialized and then re-assigned with the same value
a little later, hence the second assignment is redundant and can be
removed.
Cleans up clang warning:
drivers/usb/wusbcore/wa-nep.c:88:17: warning: Value stored to 'dev'
during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that usbip supports USB3, the maximum number of ports allowed
on a hub is 15 (USB_SS_MAXPORTS), not 31 (USB_MAXCHILDREN).
Reported-by: Gianluigi Tiesi <sherpya@netfarm.it>
Reported-by: Borissh1983 <borissh1983@gmail.com>
References: https://bugs.debian.org/878866
Fixes: 1c9de5bf42 ("usbip: vhci-hcd: Add USB3 SuperSpeed support")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel would like to have all stack VLA usage removed[1]. We
already have a pre-processor constant defined MAX_SGLEN. We can use
this instead of the variable param-sglen.
[1]: https://lkml.org/lkml/2018/3/7/621
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a USB device gets plugged on ASUS PRIME B350M-A's front ports, the
xHC stops working:
[ 549.114587] xhci_hcd 0000:02:00.0: WARN: xHC CMD_RUN timeout
[ 549.114608] suspend_common(): xhci_pci_suspend+0x0/0xc0 returns -110
[ 549.114638] xhci_hcd 0000:02:00.0: can't suspend (hcd_pci_runtime_suspend returned -110)
Delay before running xHC command CMD_RUN can workaround the issue.
Use a new quirk to make the delay only targets to the affected xHC.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch reverts the commit 835e4241e7 ("usb: host: xhci-plat:
enable clk in resume timing") because this driver also has runtime PM
and the commit 560869100b ("clk: renesas: cpg-mssr: Restore module
clocks during resume") will restore the clock on R-Car H3 environment.
If the xhci_plat_suspend() disables the clk, the system cannot enable
the clk in resume like the following behavior:
< In resume >
- genpd_resume_noirq() runs and enable the clk (enable_count = 1)
- cpg_mssr_resume_noirq() restores the clk register.
-- Since the clk was disabled in suspend, cpg_mssr_resume_noirq()
will disable the clk and keep the enable_count.
- Even if xhci_plat_resume() calls clk_prepare_enable(), since
the enable_count is 1, the clk will be not enabled.
After this patch is applied, the cpg-mssr driver will save the clk
as enable, so the clk will be enabled in resume.
Fixes: 835e4241e7 ("usb: host: xhci-plat: enable clk in resume timing")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This change fixes buffer overflows and silent data corruption with the
usbmon device driver text file read operations.
Signed-off-by: Fredrik Noring <noring@nocrew.org>
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This USB-SATA controller seems to be similar with JMicron bridge
152d:2566 already on the list. Adding it here fixes "Invalid
field in cdb" errors.
Signed-off-by: Teijo Kinnunen <teijo.kinnunen@code-q.fi>
Cc: stable@vger.kernel.org
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just small fixes now. The two most important are a fix for a a lock up
on USB ID pin change during system suspend/resume on dwc3 and a
use-after-free fix in ffs_fs_kill_sb().
Apart from that, some DT compatible fixes.
-----BEGIN PGP SIGNATURE-----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=/rNB
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.16-rc4
Just small fixes now. The two most important are a fix for a a lock up
on USB ID pin change during system suspend/resume on dwc3 and a
use-after-free fix in ffs_fs_kill_sb().
Apart from that, some DT compatible fixes.
When the host wants to fetch OS descriptors, it sends two requests. The
first is only for the header and the second for the full amount
specified by the header in the first request. The OS descriptor handling
code is distinguishing the header-only requests based on the wLength of
the setup packet, but the same code is executed in both cases to
construct the actual header. Simplify this by always constructing the
header and then filling out the rest of the request if the wLength is
greater than the size of the header.
Also remove the duplicate code for queueing the request to ep0 by adding
a goto label.
Signed-off-by: Chris Dickens <christopher.a.dickens@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When handling an OS descriptor request, one of the first operations is
to zero out the request buffer using the wLength from the setup packet.
There is no bounds checking, so a wLength > 4096 would clobber memory
adjacent to the request buffer. Fix this by taking the min of wLength
and the request buffer length prior to the memset. While at it, define
the buffer length in a header file so that magic numbers don't appear
throughout the code.
When returning data to the host, the data length should be the min of
the wLength and the valid data we have to return. Currently we are
returning wLength, thus requests for a wLength greater than the amount
of data in the OS descriptor buffer would return invalid (albeit zero'd)
data following the valid descriptor data. Fix this by counting the
number of bytes when constructing the data and using this when
determining the length of the request.
Signed-off-by: Chris Dickens <christopher.a.dickens@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The irq is available in hsotg already, so there's no need to pass it as
separate function parameter.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
As devm_ioremap_resource() checks for valid resource,
make use of it instead of testing ourselves. As a bonus
memory region is requested.
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Pointer tv_nexus is being initialized a value and this is never read
and is later being updated with the same value. Remove the redundant
initialization so that the assignment to tv_nexus is performed later
and more local to when it is being read.
Cleans up clang warning:
drivers/usb/gadget/function/f_tcm.c:1097:25: warning: Value stored to
'tv_nexus' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Due to a typo, the mask was destroyed by a comparison instead of a bit
shift.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The local variable event is of type enum usb_phy_events. Use
the same enum value USB_EVENT_NONE instead of UX500_MUSB_NONE.
This avoids a warning when building with clang:
drivers/usb/phy/phy-ab8500-usb.c:906:30: warning: implicit conversion from
enumeration type 'enum ux500_musb_vbus_id_status' to different enumeration
type 'enum usb_phy_events' [-Wenum-conversion]
enum usb_phy_events event = UX500_MUSB_NONE;
~~~~~ ^~~~~~~~~~~~~~~
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
mxs_charger_secondary_detection() is only used in this file, so make
it static.
This fixes the following sparse warning:
drivers/usb/phy/phy-mxs-usb.c:581:23: warning: symbol 'mxs_charger_secondary_detection' was not declared. Should it be static?
Acked-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use dma_pool_zalloc instead of dma_pool_alloc + memset
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Cc: John Youn <johnyoun@synopsys.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
commit d178bc3a70 ("user namespace: usb:
make usb urbs user namespace aware (v2)") changed kill_pid_info_as_uid
to kill_pid_info_as_cred, saving and passing a cred structure instead of
uids. Since the secid can be obtained from the cred, drop the secid fields
from the usb_dev_state and async structures, and drop the secid argument to
kill_pid_info_as_cred. Replace the secid argument to security_task_kill
with the cred. Update SELinux, Smack, and AppArmor to use the cred, which
avoids the need for Smack and AppArmor to use a secid at all in this hook.
Further changes to Smack might still be required to take full advantage of
this change, since it should now be possible to perform capability
checking based on the supplied cred. The changes to Smack and AppArmor
have only been compile-tested.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Acked-by: Paul Moore <paul@paul-moore.com>
Acked-by: Casey Schaufler <casey@schaufler-ca.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: John Johansen <john.johansen@canonical.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
GPL v2 is the original license according to the old license text.
See f64cdd0e94.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 57e6f0d7b8 ("typec: tcpm: Only request matching pdos") is causing
a regression, before this commit e.g. the GPD win and GPD pocket devices
were charging at 9V 3A with a PD charger, now they are instead slowly
discharging at 5V 0.4A, as this commit causes the ports max_snk_mv/ma/mw
settings to be completely ignored.
Arguably the way to fix this would be to add a PDO_VAR() describing the
voltage range to the snk_caps of boards which can handle any voltage in
their range, but the "typec: tcpm: Only request matching pdos" commit
looks at the type of PDO advertised by the source/charger and if that
is fixed (as it typically is) only compairs against PDO_FIXED entries
in the snk_caps so supporting a range of voltage would require adding a
PDO_FIXED entry for *every possible* voltage to snk_caps.
AFAICT there is no reason why a fixed source_cap cannot be matched against
a variable snk_cap, so at a minimum the commit should be rewritten to
support that.
For now lets revert the "typec: tcpm: Only request matching pdos" commit,
fixing the regression.
Fixes: 57e6f0d7b8 ("typec: tcpm: Only request matching pdos")
Cc: Badhri Jagan Sridharan <badhri@google.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without pm_runtime_{get,put}_sync calls in place, reading
vbus status via /sys causes the following error:
Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa0ab060
pgd = b333e822
[fa0ab060] *pgd=48011452(bad)
[<c05261b0>] (musb_default_readb) from [<c0525bd0>] (musb_vbus_show+0x58/0xe4)
[<c0525bd0>] (musb_vbus_show) from [<c04c0148>] (dev_attr_show+0x20/0x44)
[<c04c0148>] (dev_attr_show) from [<c0259f74>] (sysfs_kf_seq_show+0x80/0xdc)
[<c0259f74>] (sysfs_kf_seq_show) from [<c0210bac>] (seq_read+0x250/0x448)
[<c0210bac>] (seq_read) from [<c01edb40>] (__vfs_read+0x1c/0x118)
[<c01edb40>] (__vfs_read) from [<c01edccc>] (vfs_read+0x90/0x144)
[<c01edccc>] (vfs_read) from [<c01ee1d0>] (SyS_read+0x3c/0x74)
[<c01ee1d0>] (SyS_read) from [<c0106fe0>] (ret_fast_syscall+0x0/0x54)
Solution was suggested by Tony Lindgren <tony@atomide.com>.
Signed-off-by: Merlijn Wajer <merlijn@wizzup.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Corsair Strafe RGB keyboard does not respond to usb control messages
sometimes and hence generates timeouts.
Commit de3af5bf25 ("usb: quirks: add delay init quirk for Corsair
Strafe RGB keyboard") tried to fix those timeouts by adding
USB_QUIRK_DELAY_INIT.
Unfortunately, even with this quirk timeouts of usb_control_msg()
can still be seen, but with a lower frequency (approx. 1 out of 15):
[ 29.103520] usb 1-8: string descriptor 0 read error: -110
[ 34.363097] usb 1-8: can't set config #1, error -110
Adding further delays to different locations where usb control
messages are issued just moves the timeouts to other locations,
e.g.:
[ 35.400533] usbhid 1-8:1.0: can't add hid device: -110
[ 35.401014] usbhid: probe of 1-8:1.0 failed with error -110
The only way to reliably avoid those issues is having a pause after
each usb control message. In approx. 200 boot cycles no more timeouts
were seen.
Addionaly, keep USB_QUIRK_DELAY_INIT as it turned out to be necessary
to have the delay in hub_port_connect() after hub_port_init().
The overall boot time seems not to be influenced by these additional
delays, even on fast machines and lightweight distributions.
Fixes: de3af5bf25 ("usb: quirks: add delay init quirk for Corsair Strafe RGB keyboard")
Cc: stable@vger.kernel.org
Signed-off-by: Danilo Krummrich <danilokrummrich@dk-develop.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A typo broke the comparison.
Fixes: cbeef22fd6 ("usb: uas: unconditionally bring back host after reset")
Signed-off-by: Oliver Neukum <oneukum@suse.com>
CC: stable@kernel.org
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes compatible for STM32F7 USB OTG HS and consistently rename
dw2_set_params function.
The v2 former patch [1] had been acked by Paul Young, but v1 was merged.
[1] https://patchwork.kernel.org/patch/9925573/
Fixes: d8fae8b936 ("usb: dwc2: add support for STM32F7xx USB OTG HS")
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When I debug a kernel crash issue in funcitonfs, found ffs_data.ref
overflowed, While functionfs is unmounting, ffs_data is put twice.
Commit 43938613c6 ("drivers, usb: convert ffs_data.ref from atomic_t to
refcount_t") can avoid refcount overflow, but that is risk some situations.
So no need put ffs data in ffs_fs_kill_sb, already put in ffs_data_closed.
The issue can be reproduced in Mediatek mt6763 SoC, ffs for ADB device.
KASAN enabled configuration reports use-after-free errro.
BUG: KASAN: use-after-free in refcount_dec_and_test+0x14/0xe0 at addr ffffffc0579386a0
Read of size 4 by task umount/4650
====================================================
BUG kmalloc-512 (Tainted: P W O ): kasan: bad access detected
-----------------------------------------------------------------------------
INFO: Allocated in ffs_fs_mount+0x194/0x844 age=22856 cpu=2 pid=566
alloc_debug_processing+0x1ac/0x1e8
___slab_alloc.constprop.63+0x640/0x648
__slab_alloc.isra.57.constprop.62+0x24/0x34
kmem_cache_alloc_trace+0x1a8/0x2bc
ffs_fs_mount+0x194/0x844
mount_fs+0x6c/0x1d0
vfs_kern_mount+0x50/0x1b4
do_mount+0x258/0x1034
INFO: Freed in ffs_data_put+0x25c/0x320 age=0 cpu=3 pid=4650
free_debug_processing+0x22c/0x434
__slab_free+0x2d8/0x3a0
kfree+0x254/0x264
ffs_data_put+0x25c/0x320
ffs_data_closed+0x124/0x15c
ffs_fs_kill_sb+0xb8/0x110
deactivate_locked_super+0x6c/0x98
deactivate_super+0xb0/0xbc
INFO: Object 0xffffffc057938600 @offset=1536 fp=0x (null)
......
Call trace:
[<ffffff900808cf5c>] dump_backtrace+0x0/0x250
[<ffffff900808d3a0>] show_stack+0x14/0x1c
[<ffffff90084a8c04>] dump_stack+0xa0/0xc8
[<ffffff900826c2b4>] print_trailer+0x158/0x260
[<ffffff900826d9d8>] object_err+0x3c/0x40
[<ffffff90082745f0>] kasan_report_error+0x2a8/0x754
[<ffffff9008274f84>] kasan_report+0x5c/0x60
[<ffffff9008273208>] __asan_load4+0x70/0x88
[<ffffff90084cd81c>] refcount_dec_and_test+0x14/0xe0
[<ffffff9008d98f9c>] ffs_data_put+0x80/0x320
[<ffffff9008d9d904>] ffs_fs_kill_sb+0xc8/0x110
[<ffffff90082852a0>] deactivate_locked_super+0x6c/0x98
[<ffffff900828537c>] deactivate_super+0xb0/0xbc
[<ffffff90082af0c0>] cleanup_mnt+0x64/0xec
[<ffffff90082af1b0>] __cleanup_mnt+0x10/0x18
[<ffffff90080d9e68>] task_work_run+0xcc/0x124
[<ffffff900808c8c0>] do_notify_resume+0x60/0x70
[<ffffff90080866e4>] work_pending+0x10/0x14
Cc: stable@vger.kernel.org
Signed-off-by: Xinyong <xinyong.fang@linux.alibaba.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
To reproduce the lock up do the following
- connect otg host adapter and a USB device to the dual-role port
so that it is in host mode.
- suspend to mem.
- disconnect otg adapter.
- resume the system.
If we call dwc3_host_exit() before tasks are thawed
xhci_plat_remove() seems to lock up at the second usb_remove_hcd() call.
To work around this we queue the _dwc3_set_mode() work on
the system_freezable_wq.
Fixes: 41ce1456e1 ("usb: dwc3: core: make dwc3_set_mode() work properly")
Cc: <stable@vger.kernel.org> # v4.12+
Suggested-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This expands the no-op dummy functions into full prototypes to avoid
indirect call mismatches when running under Control Flow Integrity
checking, like with Clang's -fsanitize=cfi.
Co-Developed-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As done in commit:
724ba8b30b ("console/dummy: leave .con_font_get set to NULL")
This drops the dummy .con_font_get(), as it could leave arguments
uninitialized.
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are a number of USB fixes for 4.16-rc3
Nothing major, but a number of different fixes all over the place in the
USB stack for reported issues. Mostly gadget driver fixes, although the
typical set of xhci bugfixes are there, along with some new quirks
additions as well.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWo613g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymS1QCcCDbBPEJQAKF64SyHWZfebeFIBpMAnR9vku/h
1YXAXpcAJE5lGVVva3+I
=57Qr
-----END PGP SIGNATURE-----
Merge tag 'usb-4.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of USB fixes for 4.16-rc3
Nothing major, but a number of different fixes all over the place in
the USB stack for reported issues. Mostly gadget driver fixes,
although the typical set of xhci bugfixes are there, along with some
new quirks additions as well.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (39 commits)
Revert "usb: musb: host: don't start next rx urb if current one failed"
usb: musb: fix enumeration after resume
usb: cdc_acm: prevent race at write to acm while system resumes
Add delay-init quirk for Corsair K70 RGB keyboards
usb: ohci: Proper handling of ed_rm_list to handle race condition between usb_kill_urb() and finish_unlinks()
usb: host: ehci: always enable interrupt for qtd completion at test mode
usb: ldusb: add PIDs for new CASSY devices supported by this driver
usb: renesas_usbhs: missed the "running" flag in usb_dmac with rx path
usb: host: ehci: use correct device pointer for dma ops
usbip: keep usbip_device sockfd state in sync with tcp_socket
ohci-hcd: Fix race condition caused by ohci_urb_enqueue() and io_watchdog_func()
USB: serial: option: Add support for Quectel EP06
xhci: fix xhci debugfs errors in xhci_stop
xhci: xhci debugfs device nodes weren't removed after device plugged out
xhci: Fix xhci debugfs devices node disappearance after hibernation
xhci: Fix NULL pointer in xhci debugfs
xhci: Don't print a warning when setting link state for disabled ports
xhci: workaround for AMD Promontory disabled ports wakeup
usb: dwc3: core: Fix ULPI PHYs and prevent phy_get/ulpi_init during suspend/resume
USB: gadget: udc: Add missing platform_device_put() on error in bdc_pci_probe()
...
Instead of kmalloc() with manually calculated values followed by
multiple strcpy()/strcat() calls, just fold it all into a single
kasprintf() call.
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On dm3730 there are enumeration problems after resume.
Investigation led to the cause that the MUSB_POWER_SOFTCONN
bit is not set. If it was set before suspend (because it
was enabled via musb_pullup()), it is set in
musb_restore_context() so the pullup is enabled. But then
musb_start() is called which overwrites MUSB_POWER and
therefore disables MUSB_POWER_SOFTCONN, so no pullup is
enabled and the device is not enumerated.
So let's do a subset of what musb_start() does
in the same way as musb_suspend() does it. Platform-specific
stuff it still called as there might be some phy-related stuff
which needs to be enabled.
Also interrupts are enabled, as it was the original idea
of calling musb_start() in musb_resume() according to
Commit 6fc6f4b87c ("usb: musb: Disable interrupts on suspend,
enable them on resume")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
First set of fixes for current -rc cycle. Most of the changes are on
dwc3 this time around (59%) with some function changes (25%).
Out of the those, the most important fixes are:
- EP0 TRB counter fix on dwc3
- dwc3-omap stopped missing events during suspend/resume
- maxpacket size fix for ep0 in dwc3
- Descriptor processing fix for functionfs
Apart from these, your usual set of important-but-not-so-critical
fixes all over the place.
-----BEGIN PGP SIGNATURE-----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=eRDf
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.16-rc2
First set of fixes for current -rc cycle. Most of the changes are on
dwc3 this time around (59%) with some function changes (25%).
Out of the those, the most important fixes are:
- EP0 TRB counter fix on dwc3
- dwc3-omap stopped missing events during suspend/resume
- maxpacket size fix for ep0 in dwc3
- Descriptor processing fix for functionfs
Apart from these, your usual set of important-but-not-so-critical
fixes all over the place.
ACM driver may accept data to transmit while system is not fully
resumed. In this case ACM driver buffers data and prepare URBs
on usb anchor list.
There is a little chance that two tasks put a char and initiate
acm_tty_flush_chars(). In such a case, driver will put one URB
twice on usb anchor list.
This patch also reset length of data before resue of a buffer.
This not only prevent sending rubbish, but also lower risc of race.
Without this patch we hit following kernel panic in one of our
stabilty/stress tests.
[ 46.884442] *list_add double add*: new=ffff9b2ab7289330, prev=ffff9b2ab7289330, next=ffff9b2ab81e28e0.
[ 46.884476] Modules linked in: hci_uart btbcm bluetooth rfkill_gpio igb_avb(O) cfg80211 snd_soc_sst_bxt_tdf8532 snd_soc_skl snd_soc_skl_ipc snd_soc_sst_ipc snd_soc_sst_dsp snd_soc_sst_acpi snd_soc_sst_match snd_hda_ext_core snd_hda_core trusty_timer trusty_wall trusty_log trusty_virtio trusty_ipc trusty_mem trusty_irq trusty virtio_ring virtio intel_ipu4_mmu_bxtB0 lib2600_mod_bxtB0 intel_ipu4_isys_mod_bxtB0 lib2600psys_mod_bxtB0 intel_ipu4_psys_mod_bxtB0 intel_ipu4_mod_bxtB0 intel_ipu4_wrapper_bxtB0 intel_ipu4_acpi videobuf2_dma_contig as3638 dw9714 lm3643 crlmodule smiapp smiapp_pll
[ 46.884480] CPU: 1 PID: 33 Comm: kworker/u8:1 Tainted: G U W O 4.9.56-quilt-2e5dc0ac-g618ed69ced6e-dirty #4
[ 46.884489] Workqueue: events_unbound flush_to_ldisc
[ 46.884494] ffffb98ac012bb08 ffffffffad3e82e5 ffffb98ac012bb58 0000000000000000
[ 46.884497] ffffb98ac012bb48 ffffffffad0a23d1 00000024ad6374dd ffff9b2ab7289330
[ 46.884500] ffff9b2ab81e28e0 ffff9b2ab7289330 0000000000000002 0000000000000000
[ 46.884501] Call Trace:
[ 46.884507] [<ffffffffad3e82e5>] dump_stack+0x67/0x92
[ 46.884511] [<ffffffffad0a23d1>] __warn+0xd1/0xf0
[ 46.884513] [<ffffffffad0a244f>] warn_slowpath_fmt+0x5f/0x80
[ 46.884516] [<ffffffffad407443>] __list_add+0xb3/0xc0
[ 46.884521] [<ffffffffad71133c>] *usb_anchor_urb*+0x4c/0xa0
[ 46.884524] [<ffffffffad782c6f>] *acm_tty_flush_chars*+0x8f/0xb0
[ 46.884527] [<ffffffffad782cd1>] *acm_tty_put_char*+0x41/0x100
[ 46.884530] [<ffffffffad4ced34>] tty_put_char+0x24/0x40
[ 46.884533] [<ffffffffad4d3bf5>] do_output_char+0xa5/0x200
[ 46.884535] [<ffffffffad4d3e98>] __process_echoes+0x148/0x290
[ 46.884538] [<ffffffffad4d654c>] n_tty_receive_buf_common+0x57c/0xb00
[ 46.884541] [<ffffffffad4d6ae4>] n_tty_receive_buf2+0x14/0x20
[ 46.884543] [<ffffffffad4d9662>] tty_ldisc_receive_buf+0x22/0x50
[ 46.884545] [<ffffffffad4d9c05>] flush_to_ldisc+0xc5/0xe0
[ 46.884549] [<ffffffffad0bcfe8>] process_one_work+0x148/0x440
[ 46.884551] [<ffffffffad0bdc19>] worker_thread+0x69/0x4a0
[ 46.884554] [<ffffffffad0bdbb0>] ? max_active_store+0x80/0x80
[ 46.884556] [<ffffffffad0c2e10>] kthread+0x110/0x130
[ 46.884559] [<ffffffffad0c2d00>] ? kthread_park+0x60/0x60
[ 46.884563] [<ffffffffadad9917>] ret_from_fork+0x27/0x40
[ 46.884566] ---[ end trace 3bd599058b8a9eb3 ]---
Signed-off-by: Dominik Bozek <dominikx.bozek@intel.com>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that USB_UHCI_BIG_ENDIAN_MMIO and USB_UHCI_BIG_ENDIAN_DESC are moved
outside of the USB_SUPPORT conditional, simply select them from
SPARC_LEON rather than by the symbol's defaults in drivers/usb/Kconfig,
similar to how it is done for USB_EHCI_BIG_ENDIAN_MMIO and
USB_EHCI_BIG_ENDIAN_DESC.
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Corentin Labbe <clabbe.montjoie@gmail.com>
Cc: sparclinux@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Acked-by: David S. Miller <davem@davemloft.net>
Patchwork: https://patchwork.linux-mips.org/patch/18560/
Move the Kconfig symbols USB_UHCI_BIG_ENDIAN_MMIO and
USB_UHCI_BIG_ENDIAN_DESC out of drivers/usb/host/Kconfig, which is
conditional upon USB && USB_SUPPORT, so that it can be freely selected
by platform Kconfig symbols in architecture code.
For example once the MIPS_GENERIC platform selects are fixed in commit
2e6522c565 ("MIPS: Fix typo BIG_ENDIAN to CPU_BIG_ENDIAN"), the MIPS
32r6_defconfig warns like so:
warning: (MIPS_GENERIC) selects USB_UHCI_BIG_ENDIAN_MMIO which has unmet direct dependencies (USB_SUPPORT && USB)
warning: (MIPS_GENERIC) selects USB_UHCI_BIG_ENDIAN_DESC which has unmet direct dependencies (USB_SUPPORT && USB)
Fixes: 2e6522c565 ("MIPS: Fix typo BIG_ENDIAN to CPU_BIG_ENDIAN")
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: Corentin Labbe <clabbe.montjoie@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: linux-usb@vger.kernel.org
Cc: linux-mips@linux-mips.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patchwork: https://patchwork.linux-mips.org/patch/18559/
Following on from this patch: https://lkml.org/lkml/2017/11/3/516,
Corsair K70 RGB keyboards also require the DELAY_INIT quirk to
start correctly at boot.
Device ids found here:
usb 3-3: New USB device found, idVendor=1b1c, idProduct=1b13
usb 3-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 3-3: Product: Corsair K70 RGB Gaming Keyboard
Signed-off-by: Jack Stocker <jackstocker.93@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a race condition between finish_unlinks->finish_urb() function
and usb_kill_urb() in ohci controller case. The finish_urb calls
spin_unlock(&ohci->lock) before usb_hcd_giveback_urb() function call,
then if during this time, usb_kill_urb is called for another endpoint,
then new ed will be added to ed_rm_list at beginning for unlink, and
ed_rm_list will point to newly added.
When finish_urb() is completed in finish_unlinks() and ed->td_list
becomes empty as in below code (in finish_unlinks() function):
if (list_empty(&ed->td_list)) {
*last = ed->ed_next;
ed->ed_next = NULL;
} else if (ohci->rh_state == OHCI_RH_RUNNING) {
*last = ed->ed_next;
ed->ed_next = NULL;
ed_schedule(ohci, ed);
}
The *last = ed->ed_next will make ed_rm_list to point to ed->ed_next
and previously added ed by usb_kill_urb will be left unreferenced by
ed_rm_list. This causes usb_kill_urb() hang forever waiting for
finish_unlink to remove added ed from ed_rm_list.
The main reason for hang in this race condtion is addition and removal
of ed from ed_rm_list in the beginning during usb_kill_urb and later
last* is modified in finish_unlinks().
As suggested by Alan Stern, the solution for proper handling of
ohci->ed_rm_list is to remove ed from the ed_rm_list before finishing
any URBs. Then at the end, we can add ed back to the list if necessary.
This properly handle the updated ohci->ed_rm_list in usb_kill_urb().
Fixes: 977dcfdc60 ("USB: OHCI: don't lose track of EDs when a controller dies")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Aman Deep <aman.deep@samsung.com>
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At former code, the SETUP stage does not enable interrupt
for qtd completion, it relies on IAA watchdog to complete
interrupt, then the transcation would be considered timeout
if the flag need_io_watchdog is cleared by platform code.
In this commit, we always add enable interrupt for qtd completion,
then the qtd completion can be notified by hardware interrupt.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for new CASSY devices to the ldusb driver. The
PIDs are also added to the ignore list in hid-quirks.
Signed-off-by: Karsten Koop <kkoop@ld-didactic.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes an issue that a gadget driver (usb_f_fs) is possible to
stop rx transactions after the usb-dmac is used because the following
functions missed to set/check the "running" flag.
- usbhsf_dma_prepare_pop_with_usb_dmac()
- usbhsf_dma_pop_done_with_usb_dmac()
So, if next transaction uses pio, the usbhsf_prepare_pop() can not
start the transaction because the "running" flag is 0.
Fixes: 8355b2b308 ("usb: renesas_usbhs: fix the behavior of some usbhs_pkt_handle")
Cc: <stable@vger.kernel.org> # v3.19+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8c06e407e ("usb: separate out sysdev pointer from usb_bus")
converted to use hcd->self.sysdev for DMA operations instead of
hcd->self.controller, but forgot to do it for hcd test mode. Replace
the correct one in this commit.
Fixes: a8c06e407e ("usb: separate out sysdev pointer from usb_bus")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Keep usbip_device sockfd state in sync with tcp_socket. When tcp_socket
is reset to null, reset sockfd to -1 to keep it in sync.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Running io_watchdog_func() while ohci_urb_enqueue() is running can
cause a race condition where ohci->prev_frame_no is corrupted and the
watchdog can mis-detect following error:
ohci-platform 664a0800.usb: frame counter not updating; disabled
ohci-platform 664a0800.usb: HC died; cleaning up
Specifically, following scenario causes a race condition:
1. ohci_urb_enqueue() calls spin_lock_irqsave(&ohci->lock, flags)
and enters the critical section
2. ohci_urb_enqueue() calls timer_pending(&ohci->io_watchdog) and it
returns false
3. ohci_urb_enqueue() sets ohci->prev_frame_no to a frame number
read by ohci_frame_no(ohci)
4. ohci_urb_enqueue() schedules io_watchdog_func() with mod_timer()
5. ohci_urb_enqueue() calls spin_unlock_irqrestore(&ohci->lock,
flags) and exits the critical section
6. Later, ohci_urb_enqueue() is called
7. ohci_urb_enqueue() calls spin_lock_irqsave(&ohci->lock, flags)
and enters the critical section
8. The timer scheduled on step 4 expires and io_watchdog_func() runs
9. io_watchdog_func() calls spin_lock_irqsave(&ohci->lock, flags)
and waits on it because ohci_urb_enqueue() is already in the
critical section on step 7
10. ohci_urb_enqueue() calls timer_pending(&ohci->io_watchdog) and it
returns false
11. ohci_urb_enqueue() sets ohci->prev_frame_no to new frame number
read by ohci_frame_no(ohci) because the frame number proceeded
between step 3 and 6
12. ohci_urb_enqueue() schedules io_watchdog_func() with mod_timer()
13. ohci_urb_enqueue() calls spin_unlock_irqrestore(&ohci->lock,
flags) and exits the critical section, then wake up
io_watchdog_func() which is waiting on step 9
14. io_watchdog_func() enters the critical section
15. io_watchdog_func() calls ohci_frame_no(ohci) and set frame_no
variable to the frame number
16. io_watchdog_func() compares frame_no and ohci->prev_frame_no
On step 16, because this calling of io_watchdog_func() is scheduled on
step 4, the frame number set in ohci->prev_frame_no is expected to the
number set on step 3. However, ohci->prev_frame_no is overwritten on
step 11. Because step 16 is executed soon after step 11, the frame
number might not proceed, so ohci->prev_frame_no must equals to
frame_no.
To address above scenario, this patch introduces a special sentinel
value IO_WATCHDOG_OFF and set this value to ohci->prev_frame_no when
the watchdog is not pending or running. When ohci_urb_enqueue()
schedules the watchdog (step 4 and 12 above), it compares
ohci->prev_frame_no to IO_WATCHDOG_OFF so that ohci->prev_frame_no is
not overwritten while io_watchdog_func() is running.
Signed-off-by: Shigeru Yoshida <Shigeru.Yoshida@windriver.com>
Signed-off-by: Haiqing Bai <Haiqing.Bai@windriver.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Quectel EP06 is a Cat. 6 LTE modem, and the interface mapping is as
follows:
0: Diag
1: NMEA
2: AT
3: Modem
Interface 4 is QMI and interface 5 is ADB, so they are blacklisted.
This patch should also be considered for -stable. The QMI-patch for this
modem is already in the -stable-queue.
v1->v2:
* Updated commit prefix (thanks Johan Hovold)
* Updated commit message slightly.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In function xhci_stop, xhci_debugfs_exit called before xhci_mem_cleanup.
xhci_debugfs_exit removed the xhci debugfs root nodes, xhci_mem_cleanup
called function xhci_free_virt_devices_depth_first which in turn called
function xhci_debugfs_remove_slot.
Function xhci_debugfs_remove_slot removed the nodes for devices, the nodes
folders are sub folder of xhci debugfs.
It is unreasonable to remove xhci debugfs root folder before
xhci debugfs sub folder. Function xhci_mem_cleanup should be called
before function xhci_debugfs_exit.
Fixes: 02b6fdc2a1 ("usb: xhci: Add debugfs interface for xHCI driver")
Cc: <stable@vger.kernel.org> # v4.15
Signed-off-by: Zhengjun Xing <zhengjun.xing@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a bug after plugged out USB device, the device and its ep00
nodes are still kept, we need to remove the nodes in xhci_free_dev when
USB device is plugged out.
Fixes: 052f71e25a ("xhci: Fix xhci debugfs NULL pointer dereference in resume from hibernate")
Cc: <stable@vger.kernel.org> # v4.15
Signed-off-by: Zhengjun Xing <zhengjun.xing@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During system resume from hibernation, xhci host is reset, all the
nodes in devices folder are removed in xhci_mem_cleanup function.
Later nodes in /sys/kernel/debug/usb/xhci/* are created again in
function xhci_run, but the nodes already exist, so the nodes still
keep the old ones, finally device nodes in xhci debugfs folder
/sys/kernel/debug/usb/xhci/*/devices/* are disappeared.
This fix removed xhci debugfs nodes before the nodes are re-created,
so all the nodes in xhci debugfs can be re-created successfully.
Fixes: 02b6fdc2a1 ("usb: xhci: Add debugfs interface for xHCI driver")
Cc: <stable@vger.kernel.org> # v4.15
Signed-off-by: Zhengjun Xing <zhengjun.xing@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When disabling a USB3 port the hub driver will set the port link state to
U3 to prevent "ejected" or "safely removed" devices that are still
physically connected from immediately re-enumerating.
If the device was really unplugged, then error messages were printed
as the hub tries to set the U3 link state for a port that is no longer
enabled.
xhci-hcd ee000000.usb: Cannot set link state.
usb usb8-port1: cannot disable (err = -32)
Don't print error message in xhci-hub if hub tries to set port link state
for a disabled port. Return -ENODEV instead which also silences hub driver.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For AMD Promontory xHCI host, although you can disable USB ports in
BIOS settings, those ports will be enabled anyway after you remove a
device on that port and re-plug it in again. It's a known limitation of
the chip. As a workaround we can clear the PORT_WAKE_BITS.
[commit and code comment rephrasing -Mathias]
Signed-off-by: Joe Lee <asmt.swfae@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order for ULPI PHYs to work, dwc3_phy_setup() and dwc3_ulpi_init()
must be doene before dwc3_core_get_phy().
commit 541768b08a ("usb: dwc3: core: Call dwc3_core_get_phy() before initializing phys")
broke this.
The other issue is that dwc3_core_get_phy() and dwc3_ulpi_init() should
be called only once during the life cycle of the driver. However,
as dwc3_core_init() is called during system suspend/resume it will
result in multiple calls to dwc3_core_get_phy() and dwc3_ulpi_init()
which is wrong.
Fix this by moving dwc3_ulpi_init() out of dwc3_phy_setup()
into dwc3_core_ulpi_init(). Use a flag 'ulpi_ready' to ensure that
dwc3_core_ulpi_init() is called only once from dwc3_core_init().
Use another flag 'phys_ready' to call dwc3_core_get_phy() only once from
dwc3_core_init().
Fixes: 541768b08a ("usb: dwc3: core: Call dwc3_core_get_phy() before initializing phys")
Fixes: f54edb539c ("usb: dwc3: core: initialize ULPI before trying to get the PHY")
Cc: linux-stable <stable@vger.kernel.org> # >= v4.13
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add the missing platform_device_put() before return from bdc_pci_probe()
in the platform_device_add_resources() error handling case.
Fixes: efed421a94 ("usb: gadget: Add UDC driver for Broadcom USB3.0 device controller IP BDC")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We should call dwc2_hsotg_enqueue_setup() after properly
setting lx_state. Because it may cause error-out from
dwc2_hsotg_enqueue_setup() due to wrong value in lx_state.
Issue can be reproduced by loading driver while connected
A-Connector (start in A-HOST mode) then disconnect A-Connector
to switch to B-DEVICE.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
STSPHSERCVD (status phase received) interrupt should be
handled when EP0 is in DWC2_EP0_DATA_OUT state.
Sometimes STSPHSERCVD interrupt asserted , when EP0
is not in DATA_OUT state. Spurios interrupt.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In some cases device sending ZLP IN on non EP0 which
reassigning EP0 OUT descriptor pointer to that EP.
Dedicated for EP0 OUT descriptor multiple time re-used by
other EP while that descriptor already in use by EP0 OUT
for SETUP transaction. As result when SETUP packet received
BNA interrupt asserting.
In dwc2_hsotg_program_zlp() function dwc2_gadget_set_ep0_desc_chain()
must be called only for EP0.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Clang reports the following warning:
drivers/usb/gadget/udc/fsl_udc_core.c:1312:10: warning: address of array
'ep->name' will always evaluate to 'true' [-Wpointer-bool-conversion]
if (ep->name)
~~ ~~~~^~~~
It seems that the authors intention was to check if the ep has been
configured through struct_ep_setup. Check whether struct usb_ep name
pointer has been set instead.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This fixes an issue that a gadget driver (usb_f_fs) is possible to
stop rx transactions after the usb-dmac is used because the following
functions missed to set/check the "running" flag.
- usbhsf_dma_prepare_pop_with_usb_dmac()
- usbhsf_dma_pop_done_with_usb_dmac()
So, if next transaction uses pio, the usbhsf_prepare_pop() can not
start the transaction because the "running" flag is 0.
Fixes: 8355b2b308 ("usb: renesas_usbhs: fix the behavior of some usbhs_pkt_handle")
Cc: <stable@vger.kernel.org> # v3.19+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
USB_GADGET_DUALSPEED was removed by commit 85b8614d72 ("usb: gadget:
get rid of USB_GADGET_{DUAL,SUPER}SPEED"), but the USB_SNP_UDC_PLAT
symbol still selects it.
Remove the USB_GADGET_DUALSPEED select from USB_SNP_UDC_PLAT.
Discovered with the
https://github.com/ulfalizer/Kconfiglib/blob/master/examples/list_undefined.py
script.
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The FIFO/Queue type values are incorrect. Correct them according to
DWC_usb3 programming guide section 1.2.27 (or DWC_usb31 section 1.2.25).
Additionally, this patch includes ProtocolStatusQ and AuxEventQ types.
Fixes: cf6d867d3b ("usb: dwc3: core: add fifo space helper")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Driver is tracing usb_request after freeing it.
Fix it by changing the order.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The USB cable state can change during suspend/resume
so be sure to check and update the extcon state.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In commit 2bfa0719ac ("usb: gadget: function: f_fs: pass
companion descriptor along") there is a pointer arithmetic
bug where the comp_desc is obtained as follows:
comp_desc = (struct usb_ss_ep_comp_descriptor *)(ds +
USB_DT_ENDPOINT_SIZE);
Since ds is a pointer to usb_endpoint_descriptor, adding
7 to it ends up going out of bounds (7 * sizeof(struct
usb_endpoint_descriptor), which is actually 7*9 bytes) past
the SS descriptor. As a result the maxburst value will be
read incorrectly, and the UDC driver will also get a garbage
comp_desc (assuming it uses it).
Since Felipe wrote, "Eventually, f_fs.c should be converted
to use config_ep_by_speed() like all other functions, though",
let's finally do it. This allows the other usb_ep fields to
be properly populated, such as maxpacket and mult. It also
eliminates the awkward speed-based descriptor lookup since
config_ep_by_speed() does that already using the ones found
in struct usb_function.
Fixes: 2bfa0719ac ("usb: gadget: function: f_fs: pass companion descriptor along")
Cc: stable@vger.kernel.org
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
During _ffs_func_bind(), the received descriptors are evaluated
to prepare for binding with the gadget in order to allocate
endpoints and optionally set up OS descriptors. However, the
high- and super-speed descriptors are only parsed based on
whether the gadget_is_dualspeed() and gadget_is_superspeed()
calls are true, respectively.
This is a problem in case a userspace program always provides
all of the {full,high,super,OS} descriptors when configuring a
function. Then, for example if a gadget device is not capable
of SuperSpeed, the call to ffs_do_descs() for the SS descriptors
is skipped, resulting in an incorrect offset calculation for
the vla_ptr when moving on to the OS descriptors that follow.
This causes ffs_do_os_descs() to fail as it is now looking at
the SS descriptors' offset within the raw_descs buffer instead.
_ffs_func_bind() should evaluate the descriptors unconditionally,
so remove the checks for gadget speed.
Fixes: f0175ab519 ("usb: gadget: f_fs: OS descriptors support")
Cc: stable@vger.kernel.org
Co-Developed-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Commit e93650994a ("usb: phy: mxs: add usb charger type detection")
causes the following kernel hang on i.MX28:
[ 2.207973] usbcore: registered new interface driver usb-storage
[ 2.235659] Unable to handle kernel NULL pointer dereference at virtual address 00000188
[ 2.244195] pgd = (ptrval)
[ 2.246994] [00000188] *pgd=00000000
[ 2.250676] Internal error: Oops: 5 [#1] ARM
[ 2.254979] Modules linked in:
[ 2.258089] CPU: 0 PID: 1 Comm: swapper Not tainted 4.15.0-rc8-next-20180117-00002-g75d5f21 #7
[ 2.266724] Hardware name: Freescale MXS (Device Tree)
[ 2.271921] PC is at regmap_read+0x0/0x5c
[ 2.275977] LR is at mxs_phy_charger_detect+0x34/0x1dc
mxs_phy_charger_detect() makes accesses to the anatop registers via regmap,
however i.MX23/28 do not have such registers, which causes a NULL pointer
dereference.
Fix the issue by doing a NULL check on the 'regmap' pointer.
Fixes: e93650994a ("usb: phy: mxs: add usb charger type detection")
Cc: <stable@vger.kernel.org> # v4.15
Reviewed-by: Li Jun <jun.li@nxp.com>
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Commit 689bf72c6e ("usb: dwc3: Don't reinitialize core during
host bus-suspend/resume") updated suspend/resume routines to not
power_off and reinit PHYs/core for host mode.
It broke platforms that rely on DWC3 core to power_off PHYs to
enter low power state on system suspend.
Perform dwc3_core_exit/init only during host mode system_suspend/
resume to addresses power regression from above mentioned patch
and also allow USB session to stay connected across
runtime_suspend/resume in host mode. While at it also replace
existing checks for HOST only dr_mode with current_dr_role to
have similar core driver behavior for both Host-only and DRD+Host
configurations.
Fixes: 689bf72c6e ("usb: dwc3: Don't reinitialize core during host bus-suspend/resume")
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In this function, we init the USB2 and USB3 PHYs, but if soft reset
times out, we don't unwind this.
Noticed by inspection.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If there are multiple functions associated with a configuration, then
the UAC2 interfaces may not start at zero. Set the correct first
interface number in the association descriptor so that the audio
interfaces are enumerated correctly in this case.
Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
DWC3 tracks TRB counter for each ep0 direction separately. In control
read transfer completion handler, the driver needs to reset the TRB
enqueue counter for ep0 IN direction. Currently the driver only resets
the TRB counter for control OUT endpoint. Check for the data direction
and properly reset the TRB counter from correct control endpoint.
Cc: stable@vger.kernel.org
Fixes: c2da2ff006 ("usb: dwc3: ep0: don't use ep0in for transfers")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There are 2 control endpoint structures for DWC3. However, the driver
only updates the OUT direction control endpoint structure during
ConnectDone event. DWC3 driver needs to update the endpoint max packet
size for control IN endpoint as well. If the max packet size is not
properly set, then the driver will incorrectly calculate the data
transfer size and fail to send ZLP for HS/FS 3-stage control read
transfer.
The fix is simply to update the max packet size for the ep0 IN direction
during ConnectDone event.
Cc: stable@vger.kernel.org
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes an issue that the renesas_usb3_remove() causes
NULL pointer dereference because the usb3_to_dev() macro will use
the gadget instance and it will be deleted before.
Fixes: cf06df3fae ("usb: gadget: udc: renesas_usb3: move pm_runtime_{en,dis}able()")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc3_of_simple_dev_pm_ops has never been used since commit a0d8c4cfdf
("usb: dwc3: of-simple: set dev_pm_ops"), but this commit has brought
and oops when unbind the device due this sequence:
dwc3_of_simple_remove
-> clk_disable ...
-> pm_runtime_put_sync
-> dwc3_of_simple_runtime_suspend
-> clk_disable (again)
This double call to clk_core_disable causes a kernel oops like this:
WARNING: CPU: 1 PID: 4022 at drivers/clk/clk.c:656 clk_core_disable+0x78/0x80
CPU: 1 PID: 4022 Comm: bash Not tainted 4.15.0-rc4+ #44
Hardware name: Google Kevin (DT)
pstate: 80000085 (Nzcv daIf -PAN -UAO)
pc : clk_core_disable+0x78/0x80
lr : clk_core_disable_lock+0x20/0x38
sp : ffff00000bbf3a90
...
Call trace:
clk_core_disable+0x78/0x80
clk_disable+0x1c/0x30
dwc3_of_simple_runtime_suspend+0x30/0x50
pm_generic_runtime_suspend+0x28/0x40
This patch fixes the unbalanced clk disable call by setting the num_clocks
variable to zero once the clocks were disabled.
Fixes: a0d8c4cfdf ("usb: dwc3: of-simple: set dev_pm_ops")
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with reworks
to try to attempt to make the code easier to handle in the long run, but
no functional change. There's also some tree-wide sysfs attribute
fixups with lots of acks from the various subsystem maintainers, as well
as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWnLvPw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynNzACgkzjPoBytJWbpWFt6SR6L33/u4kEAnRFvVCGL
s6ygQPQhZIjKk2Lxa2hC
=Zihy
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with
reworks to try to attempt to make the code easier to handle in the
long run, but no functional change. There's also some tree-wide sysfs
attribute fixups with lots of acks from the various subsystem
maintainers, as well as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues"
* tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (48 commits)
device property: Define type of PROPERTY_ENRTY_*() macros
device property: Reuse property_entry_free_data()
device property: Move property_entry_free_data() upper
firmware: Fix up docs referring to FIRMWARE_IN_KERNEL
firmware: Drop FIRMWARE_IN_KERNEL Kconfig option
USB: serial: keyspan: Drop firmware Kconfig options
sysfs: remove DEBUG defines
sysfs: use SPDX identifiers
drivers: base: add coredump driver ops
sysfs: add attribute specification for /sysfs/devices/.../coredump
test_firmware: fix missing unlock on error in config_num_requests_store()
test_firmware: make local symbol test_fw_config static
sysfs: turn WARN() into pr_warn()
firmware: Fix a typo in fallback-mechanisms.rst
treewide: Use DEVICE_ATTR_WO
treewide: Use DEVICE_ATTR_RO
treewide: Use DEVICE_ATTR_RW
sysfs.h: Use octal permissions
component: add debugfs support
bus: simple-pm-bus: convert bool SIMPLE_PM_BUS to tristate
...
Here is the big USB and PHY driver update for 4.16-rc1.
Along with the normally expected XHCI, MUSB, and Gadget driver patches,
there are some PHY driver fixes, license cleanups, sysfs attribute
cleanups, usbip changes, and a raft of other smaller fixes and
additions.
Full details are in the shortlog.
All of these have been in the linux-next tree for a long time with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWnL0Bg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymg8gCeLg/FMtc0S/xRR/56N/sbthEebcUAnROr9Sg3
55hDLdkyi93o9R86YOAJ
=8d2q
-----END PGP SIGNATURE-----
Merge tag 'usb-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big USB and PHY driver update for 4.16-rc1.
Along with the normally expected XHCI, MUSB, and Gadget driver
patches, there are some PHY driver fixes, license cleanups, sysfs
attribute cleanups, usbip changes, and a raft of other smaller fixes
and additions.
Full details are in the shortlog.
All of these have been in the linux-next tree for a long time with no
reported issues"
* tag 'usb-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (137 commits)
USB: serial: pl2303: new device id for Chilitag
USB: misc: fix up some remaining DEVICE_ATTR() usages
USB: musb: fix up one odd DEVICE_ATTR() usage
USB: atm: fix up some remaining DEVICE_ATTR() usage
USB: move many drivers to use DEVICE_ATTR_WO
USB: move many drivers to use DEVICE_ATTR_RO
USB: move many drivers to use DEVICE_ATTR_RW
USB: misc: chaoskey: Use true and false for boolean values
USB: storage: remove old wording about how to submit a change
USB: storage: remove invalid URL from drivers
usb: ehci-omap: don't complain on -EPROBE_DEFER when no PHY found
usbip: list: don't list devices attached to vhci_hcd
usbip: prevent bind loops on devices attached to vhci_hcd
USB: serial: remove redundant initializations of 'mos_parport'
usb/gadget: Fix "high bandwidth" check in usb_gadget_ep_match_desc()
usb: gadget: compress return logic into one line
usbip: vhci_hcd: update 'status' file header and format
USB: serial: simple: add Motorola Tetra driver
CDC-ACM: apply quirk for card reader
usb: option: Add support for FS040U modem
...
Pull poll annotations from Al Viro:
"This introduces a __bitwise type for POLL### bitmap, and propagates
the annotations through the tree. Most of that stuff is as simple as
'make ->poll() instances return __poll_t and do the same to local
variables used to hold the future return value'.
Some of the obvious brainos found in process are fixed (e.g. POLLIN
misspelled as POLL_IN). At that point the amount of sparse warnings is
low and most of them are for genuine bugs - e.g. ->poll() instance
deciding to return -EINVAL instead of a bitmap. I hadn't touched those
in this series - it's large enough as it is.
Another problem it has caught was eventpoll() ABI mess; select.c and
eventpoll.c assumed that corresponding POLL### and EPOLL### were
equal. That's true for some, but not all of them - EPOLL### are
arch-independent, but POLL### are not.
The last commit in this series separates userland POLL### values from
the (now arch-independent) kernel-side ones, converting between them
in the few places where they are copied to/from userland. AFAICS, this
is the least disruptive fix preserving poll(2) ABI and making epoll()
work on all architectures.
As it is, it's simply broken on sparc - try to give it EPOLLWRNORM and
it will trigger only on what would've triggered EPOLLWRBAND on other
architectures. EPOLLWRBAND and EPOLLRDHUP, OTOH, are never triggered
at all on sparc. With this patch they should work consistently on all
architectures"
* 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
make kernel-side POLL... arch-independent
eventpoll: no need to mask the result of epi_item_poll() again
eventpoll: constify struct epoll_event pointers
debugging printk in sg_poll() uses %x to print POLL... bitmap
annotate poll(2) guts
9p: untangle ->poll() mess
->si_band gets POLL... bitmap stored into a user-visible long field
ring_buffer_poll_wait() return value used as return value of ->poll()
the rest of drivers/*: annotate ->poll() instances
media: annotate ->poll() instances
fs: annotate ->poll() instances
ipc, kernel, mm: annotate ->poll() instances
net: annotate ->poll() instances
apparmor: annotate ->poll() instances
tomoyo: annotate ->poll() instances
sound: annotate ->poll() instances
acpi: annotate ->poll() instances
crypto: annotate ->poll() instances
block: annotate ->poll() instances
x86: annotate ->poll() instances
...
Pull siginfo cleanups from Eric Biederman:
"Long ago when 2.4 was just a testing release copy_siginfo_to_user was
made to copy individual fields to userspace, possibly for efficiency
and to ensure initialized values were not copied to userspace.
Unfortunately the design was complex, it's assumptions unstated, and
humans are fallible and so while it worked much of the time that
design failed to ensure unitialized memory is not copied to userspace.
This set of changes is part of a new design to clean up siginfo and
simplify things, and hopefully make the siginfo handling robust enough
that a simple inspection of the code can be made to ensure we don't
copy any unitializied fields to userspace.
The design is to unify struct siginfo and struct compat_siginfo into a
single definition that is shared between all architectures so that
anyone adding to the set of information shared with struct siginfo can
see the whole picture. Hopefully ensuring all future si_code
assignments are arch independent.
The design is to unify copy_siginfo_to_user32 and
copy_siginfo_from_user32 so that those function are complete and cope
with all of the different cases documented in signinfo_layout. I don't
think there was a single implementation of either of those functions
that was complete and correct before my changes unified them.
The design is to introduce a series of helpers including
force_siginfo_fault that take the values that are needed in struct
siginfo and build the siginfo structure for their callers. Ensuring
struct siginfo is built correctly.
The remaining work for 4.17 (unless someone thinks it is post -rc1
material) is to push usage of those helpers down into the
architectures so that architecture specific code will not need to deal
with the fiddly work of intializing struct siginfo, and then when
struct siginfo is guaranteed to be fully initialized change copy
siginfo_to_user into a simple wrapper around copy_to_user.
Further there is work in progress on the issues that have been
documented requires arch specific knowledge to sort out.
The changes below fix or at least document all of the issues that have
been found with siginfo generation. Then proceed to unify struct
siginfo the 32 bit helpers that copy siginfo to and from userspace,
and generally clean up anything that is not arch specific with regards
to siginfo generation.
It is a lot but with the unification you can of siginfo you can
already see the code reduction in the kernel"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (45 commits)
signal/memory-failure: Use force_sig_mceerr and send_sig_mceerr
mm/memory_failure: Remove unused trapno from memory_failure
signal/ptrace: Add force_sig_ptrace_errno_trap and use it where needed
signal/powerpc: Remove unnecessary signal_code parameter of do_send_trap
signal: Helpers for faults with specialized siginfo layouts
signal: Add send_sig_fault and force_sig_fault
signal: Replace memset(info,...) with clear_siginfo for clarity
signal: Don't use structure initializers for struct siginfo
signal/arm64: Better isolate the COMPAT_TASK portion of ptrace_hbptriggered
ptrace: Use copy_siginfo in setsiginfo and getsiginfo
signal: Unify and correct copy_siginfo_to_user32
signal: Remove the code to clear siginfo before calling copy_siginfo_from_user32
signal: Unify and correct copy_siginfo_from_user32
signal/blackfin: Remove pointless UID16_SIGINFO_COMPAT_NEEDED
signal/blackfin: Move the blackfin specific si_codes to asm-generic/siginfo.h
signal/tile: Move the tile specific si_codes to asm-generic/siginfo.h
signal/frv: Move the frv specific si_codes to asm-generic/siginfo.h
signal/ia64: Move the ia64 specific si_codes to asm-generic/siginfo.h
signal/powerpc: Remove redefinition of NSIGTRAP on powerpc
signal: Move addr_lsb into the _sigfault union for clarity
...
This adds a new device id for Chilitag devices to the pl2303 driver.
Reported-by: "Chu.Mike [朱堅宜]" <Mike-Chu@prolific.com.tw>
Cc: stable <stable@vger.kernel.org>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For all of these, a simple DEVICE_ATTR_*() macro should be used instead,
so convert the drivers to use them.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It really should be DEVICE_ATTR_WO(), no need to "open code" it.
Acked-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's no need to have DEVICE_ATTR() in these crazy macros, so use the
proper DEVICE_ATTR_*() versions intead.
Cc: Matthieu CASTET <castet.matthieu@free.fr>
Cc: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of "open coding" a DEVICE_ATTR() define, use the
DEVICE_ATTR_WO() macro instead, which does everything properly instead.
This does require a few static functions to be renamed to work properly,
but thanks to a script from Joe Perches, this was easily done.
Reported-by: Joe Perches <joe@perches.com>
Cc: Peter Chen <Peter.Chen@nxp.com>
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of "open coding" a DEVICE_ATTR() define, use the
DEVICE_ATTR_RO() macro instead, which does everything properly instead.
This does require a few static functions to be renamed to work properly,
but thanks to a script from Joe Perches, this was easily done.
Reported-by: Joe Perches <joe@perches.com>
Cc: Matthieu CASTET <castet.matthieu@free.fr>
Cc: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: Oliver Neukum <oneukum@suse.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of "open coding" a DEVICE_ATTR() define, use the
DEVICE_ATTR_RW() macro instead, which does everything properly instead.
This does require a few static functions to be renamed to work properly,
but thanks to a script from Joe Perches, this was easily done.
Reported-by: Joe Perches <joe@perches.com>
Cc: Matthieu CASTET <castet.matthieu@free.fr>
Cc: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: Peter Chen <Peter.Chen@nxp.com>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Assign true or false to boolean variables instead of an integer value.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's best to just send new updates to the usb-storage quirk table to the
linux-usb@vger.kernel.org mailing list, no need to bother Phil and Alan
or the almost defunct usb-storage list.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: Phil Dibowitz <phil@ipom.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The old URL for usb-storage driver help is long gone. So remove it from
the comments to not confuse people anymore.
Reported-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function clear_siginfo is just a nice wrapper around memset so
this results in no functional change. This change makes mistakes
a little more difficult and it makes it clearer what is going on.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Don't complain on -EPROBE_DEFER when no PHY found, the driver
probe will be retried later.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pointer mos_parport is being initialized to pp->private_data and
then the assignment is duplicated after a spin lock. Remove the
initialization as it occurs before the spin lock and it is a redundant
assignment.
Cleans up clang warnings:
drivers/usb/serial/mos7720.c:521:26: warning: Value stored to
'mos_parport' during its initialization is never read
drivers/usb/serial/mos7720.c:557:26: warning: Value stored to
'mos_parport' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current code tries to test for bits that are masked out by
usb_endpoint_maxp(). Instead, use the proper accessor to access
the new high bandwidth bits.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 2f2d0088eb
("usbip: prevent vhci_hcd driver from leaking a socket pointer address")
in the /sys/devices/platform/vhci_hcd/status.
Fix the header and field alignment to reflect the changes and make it
easier to read.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This devices drops random bytes from messages if you talk to it
too fast.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
FS040U modem is manufactured by omega, and sold by Fujisoft. This patch
adds ID of the modem to use option1 driver. Interface 3 is used as
qmi_wwan, so the interface is ignored.
Signed-off-by: Yoshiaki Okamoto <yokamoto@allied-telesis.co.jp>
Signed-off-by: Hiroyuki Yamamoto <hyamamo@allied-telesis.co.jp>
Cc: stable <stable@vger.kernel.org>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Aspeed SoCs use uhci-platform. With the new dynamic clock
control framework, the corresponding IP block clock must be
properly enabled.
This is a simplified variant of what ehci-platform does, it
looks for *one* clock attached to the device, and if it's
there, enables it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Quoting Hans:
If we return 1 from our post_reset handler, then our disconnect handler
will be called immediately afterwards. Since pre_reset blocks all scsi
requests our disconnect handler will then hang in the scsi_remove_host
call.
This is esp. bad because our disconnect handler hanging for ever also
stops the USB subsys from enumerating any new USB devices, causes commands
like lsusb to hang, etc.
In practice this happens when unplugging some uas devices because the hub
code may see the device as needing a warm-reset and calls usb_reset_device
before seeing the disconnect. In this case uas_configure_endpoints fails
with -ENODEV. We do not want to print an error for this, so this commit
also silences the shost_printk for -ENODEV.
ENDQUOTE
However, if we do that we better drop any unconditional execution
and report to the SCSI subsystem that we have undergone a reset
but we are not operational now.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-by: Hans de Goede <hdegoede@redhat.com>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When disconnected sometimes the cdc-acm driver logs errors like these:
[20278.039417] cdc_acm 2-2:2.1: urb 9 failed submission with -19
[20278.042924] cdc_acm 2-2:2.1: urb 10 failed submission with -19
[20278.046449] cdc_acm 2-2:2.1: urb 11 failed submission with -19
[20278.049920] cdc_acm 2-2:2.1: urb 12 failed submission with -19
[20278.053442] cdc_acm 2-2:2.1: urb 13 failed submission with -19
[20278.056915] cdc_acm 2-2:2.1: urb 14 failed submission with -19
[20278.060418] cdc_acm 2-2:2.1: urb 15 failed submission with -19
Silence these by not logging errors when the result is -ENODEV.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changing from ssusb_wakeup_enable/disable to ssusb_wakeup_set was done
in only one of two places in the kernel, the other one now causes a
build failure:
drivers/usb/mtu3/mtu3_plat.c: In function 'mtu3_suspend':
drivers/usb/mtu3/mtu3_plat.c:462:2: error: implicit declaration of function 'ssusb_wakeup_set'; did you mean 'ssusb_wakeup_disable'? [-Werror=implicit-function-declaration]
This adapts the dummy helpers the same way that the extern declarations
were.
Fixes: f0ede2c628 ("usb: mtu3: supports remote wakeup for mt2712 with two SSUSB IPs")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tx_tasklet tasklet is used in invoke the hrtimer (task_timer) in
softirq context. This can be also achieved without the tasklet but
with HRTIMER_MODE_SOFT as hrtimer mode.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: keescook@chromium.org
Cc: linux-usb@vger.kernel.org
Link: http://lkml.kernel.org/r/20171221104205.7269-36-anna-maria@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Here are the USB-serial updates for 4.16-rc1, including:
- a fix for a potential sleep-while-atomic (warning) in an io_edgeport
error path
- removal of a dummy TIOCSSERIAL implementation in ark3116
- new features for Fintek F81532/534 devices:
- support for higher baud rates (up to 1.5 Mbps)
- support for auto-RTS (for RS-485)
- support for transceiver configuration
- support for detecting disabled ports
Included are also various clean ups.
All have been (at least compile tested) in linux-next without any
reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=ZTZB
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.16-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.16-rc1
Here are the USB-serial updates for 4.16-rc1, including:
- a fix for a potential sleep-while-atomic (warning) in an io_edgeport
error path
- removal of a dummy TIOCSSERIAL implementation in ark3116
- new features for Fintek F81532/534 devices:
- support for higher baud rates (up to 1.5 Mbps)
- support for auto-RTS (for RS-485)
- support for transceiver configuration
- support for detecting disabled ports
Included are also various clean ups.
All have been (at least compile tested) in linux-next without any
reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
When using a GPIO which is high by default, and initialize the
driver in USB Hub mode, initialization fails with:
[ 111.757794] usb3503 0-0008: SP_ILOCK failed (-5)
The reason seems to be that the chip is not properly reset.
Probe does initialize reset low, however some lines later the
code already set it back high, which is not long enouth.
Make sure reset is asserted for at least 100us by inserting a
delay after initializing the reset pin during probe.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are a couple of new device ids for cp210x.
Both have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=LzG1
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.15-rc8' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.15-rc8
Here are a couple of new device ids for cp210x.
Both have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
The F81532/534 had 4 clocksource 1.846/18.46/14.77/24MHz and baud rates
can be up to 1.5Mbits with 24MHz. But on some baud rate (384~500kps), the
TX side will send the data frame too close to treat frame error on RX
side. This patch will force all TX data frame with delay 1bit gap.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The F81532/534 can be disable port by manufacturer with
following H/W design.
1: Connect DCD/DSR/CTS/RI pin to ground.
2: Connect RX pin to ground.
In driver, we'll implements some detect method likes following:
1: Read MSR.
2: Turn MCR LOOP bit on, off and read LSR after delay with 60ms.
It'll contain BREAK status in LSR.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
In the original code, We'll read configuration in calc_num_ports()
and read again in attach(). In fact, we can move all content from
attach() to calc_num_ports() to simplify the code.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
[ johan: replace commit summary ]
Signed-off-by: Johan Hovold <johan@kernel.org>
The F81532/534 had 3 output pin (M0/SD, M1, M2) with open-drain mode to
control transceiver. We'll read it from internal Flash with address
0x2f05~0x2f08 for 4 ports. The value is range from 0 to 7. The M0/SD is
MSB of this value. For a examples, If read value is 6, we'll write M0/SD,
M1, M2 as 1, 1, 0.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The F81532/534 had auto RTS direction support for RS485 mode.
We'll read it from internal Flash with address 0x2f01~0x2f04 for 4 ports.
There are 4 conditions below:
0: F81534_PORT_CONF_RS232.
1: F81534_PORT_CONF_RS485.
2: value error, default to F81534_PORT_CONF_RS232.
3: F81534_PORT_CONF_RS485_INVERT.
F81532/534 Clock register (offset +08h)
Bit0: UART Enable (always on)
Bit2-1: Clock source selector
00: 1.846MHz.
01: 18.46MHz.
10: 24MHz.
11: 14.77MHz.
Bit4: Auto direction(RTS) control (RTS pin Low when TX)
Bit5: Invert direction(RTS) when Bit4 enabled (RTS pin high when TX)
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
[ johan: rename mode-mask define, and only use GENMASK() for masks ]
Signed-off-by: Johan Hovold <johan@kernel.org>
The F81532/534 had 4 clocksource 1.846/18.46/14.77/24MHz and baud rates
can be up to 1.5Mbits with 24MHz.
This device may generate data overrun when baud rate setting to 921600bps
or higher with old UART trigger level setting (8x14=112) with full
loading. We'll change trigger level from 8x14=112 to 8x8=64 to avoid data
overrun.
Also the read/write of EP0 will be affected by this patch. The worst case
of responding time is 20s when all serial port are full loading and trying
to access EP0, so we change EP0 timeout from 10 to 20s.
F81532/534 Clock register (offset +08h)
Bit0: UART Enable (always on)
Bit2-1: Clock source selector
00: 1.846MHz.
01: 18.46MHz.
10: 24MHz.
11: 14.77MHz.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
[ johan: only use GENMASK() for masks ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Use aligned DMA on Tegra30, and USB Ethernet gadget now works on it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaVWkqAAoJEEhZKYFQ1nG78J4H/2tMTfAHjF4orRsxysrhqmyp
mQpIYjFLWo4BbMn58W85WR/kne9hcF9pA9FgVVWjVZrJK0689BtJVylN13sYl5tN
3BfYzkthmHtMQEzqQyyG+CmUPWjJCrvmYy2K7r1iI+scK3ThAXHVZgJafvIf0Cuu
7V83xKWUIHojGRtlEvBTz8PcHU+XnrkwyTLIAkRV4SKIeiOyTIXWtAnP2Qyy4RkT
GYq/9JgNKCbRbLw9stg0WTFEA1/iQutYveCSwuZFWY5PvK1fib0hmKDWvm14S0xb
vuSdOqeEWxWewkjjdIWQzsDG8ATQMWmOaFsVo00neD//socbWew0676INJo2OwY=
=Bp26
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
Just one small update:
Use aligned DMA on Tegra30, and USB Ethernet gadget now works on it.
The UAS mode of Norelsys NS1068(X) is reported to fail to work on
several platforms with the following error message:
xhci-hcd xhci-hcd.0.auto: ERROR Transfer event for unknown stream ring slot 1 ep 8
xhci-hcd xhci-hcd.0.auto: @00000000bf04a400 00000000 00000000 1b000000 01098001
And when trying to mount a partition on the disk the disk will
disconnect from the USB controller, then after re-connecting the device
will be offlined and not working at all.
Falling back to USB mass storage can solve this problem, so ignore UAS
function of this chip.
Cc: stable@vger.kernel.org
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The old way of usb wakeup only supports platform with single xHCI IP,
such as mt8173, but mt2712 has two xHCI IPs, so rebuild its flow and
supports the new glue layer of usb wakeup on mt2712 which is different
from mt8173.
Due to there is a hardware bug with the LINE STATE wakeup mode on
mt8173 which causes wakeup failure by low speed devices, and also
because IP SLEEP mode can cover all functions of LINE STATE mode,
it is unused in fact, and will not support it later, so remove it at
the same time.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The old way of usb wakeup only supports platform with single SSUSB IP,
such as mt8173, but mt2712 has two SSUSB IPs, so rebuild its flow and
also supports the new glue layer of usb wakeup on mt2712 which is
different from mt8173.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When failing to get extcon device, extcon_get_edev_by_phandle()
may return different error codes, but not only -EPROBE_DEFER,
so can't always return -EPROBE_DEFER, and fix it.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the capability to support RZ/A1 SoCs.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Upon usb composition switch there is possibility of ep0 file
release happening after gadget driver bind. In case of composition
switch from adb to a non-adb composition gadget will never gets
bound again resulting into failure of usb device enumeration. Fix
this issue by checking FFS_FL_BOUND flag and avoid extra
gadget driver unbind if it is already done as part of composition
switch.
This fixes adb reconnection error reported on Android running
v4.4 and above kernel versions. Verified on Hikey running vanilla
v4.15-rc7 + few out of tree Mali patches.
Reviewed-at: https://android-review.googlesource.com/#/c/582632/
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg KH <gregkh@linux-foundation.org>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Dmitry Shmidt <dimitrysh@google.com>
Cc: Badhri <badhri@google.com>
Cc: Android Kernel Team <kernel-team@android.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
[AmitP: Cherry-picked it from android-4.14 and updated the commit log]
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ohci-da8xx device only has one clock, so a con_id is not needed, so
remove it. This way we don't have to add an unnecessary property to the
device tree bindings for the clock.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is only one clock for the DA8xx MUSB device, so we don't need the
con_id, so remove it. This way we don't have to add an unnecessary
property to the device tree bindings for the clock.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The error-handling pathways in usb_add_gadget_udc_release() are messed
up. Aside from the uninformative statement labels, they can deallocate
the udc structure after calling put_device(), which is a double-free.
This was observed by KASAN in automatic testing.
This patch cleans up the routine. It preserves the requirement that
when any failure occurs, we call put_device(&gadget->dev).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
CC: <stable@vger.kernel.org>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Automated tests triggered this by opening usbmon and accessing the
mmap while simultaneously resizing the buffers. This bug was with
us since 2006, because typically applications only size the buffers
once and thus avoid racing. Reported by Kirill A. Shutemov.
Reported-by: <syzbot+f9831b881b3e849829fc@syzkaller.appspotmail.com>
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch moves TIOCGSERIAL ioctl case to get_serial_info function.
Signed-off-by: Mikhail Zaytsev <flashed@mail.ru>
[johan: keep the automatic __user pointer variable in ioctl callback ]
Signed-off-by: Johan Hovold <johan@kernel.org>
The patch removes unused TIOCSSERIAL ioctl case and adds the default block
to the switch. This will make the ioctl return -ENOTTY to user space (e.g.
setserial), which indicates that TIOCSSERIAL really isn't supported for
these devices currently.
Note that these (dummy) ioctl implementations where added by commit
2f430b4bba ("USB: ark3116: Add TIOCGSERIAL and TIOCSSERIAL ioctl
calls.") back in 2006. This in turn appears to have been triggered by a
change in a user space tool, wvdial, which started erroring out if
either was missing.
There are some bug reports about that against wvdial from around that
time, and looking at the wvstreams (library) code now, it looks like the
issue has indeed been resolved by handling errors more gracefully (e.g.
just logging them).
User space really should not make assumptions about these ioctl always
being implemented, but if this turns out to be a problem for anyone
using this driver, we'll add TIOCSSERIAL back in some form.
Signed-off-by: Mikhail Zaytsev <flashed@mail.ru>
[johan: amend commit message with backstory ]
Signed-off-by: Johan Hovold <johan@kernel.org>
*) Fix in exynos5-usbdrd to enumerate SuperSpeed devices on Odroid XU3
*) Fix in Broadcom USB PHY to get Dell Low Speed keyboards working
*) Fix in Broadcom USB PHY to power down the PHY when XHCI disabled
to save power
*) Fix in Broadcom USB PHY to prevent abort in DRD mode
*) Fix in Broadcom USB PHY to use the correct dt properties
*) Fix in Mediatek PHY to detect device connection
*) Make getting resource optional for Mediatek V1 TPHY
*) Cleanup in Mediatek PHY
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=f9so
-----END PGP SIGNATURE-----
Merge tag 'phy-for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 4.16
*) Fix in exynos5-usbdrd to enumerate SuperSpeed devices on Odroid XU3
*) Fix in Broadcom USB PHY to get Dell Low Speed keyboards working
*) Fix in Broadcom USB PHY to power down the PHY when XHCI disabled
to save power
*) Fix in Broadcom USB PHY to prevent abort in DRD mode
*) Fix in Broadcom USB PHY to use the correct dt properties
*) Fix in Mediatek PHY to detect device connection
*) Make getting resource optional for Mediatek V1 TPHY
*) Cleanup in Mediatek PHY
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Not many changes here, the most important being an improvement for TI's
AM57xx and DRA7xx devices which allows them to disable a metastability
workaround in situations where we know what's going on.
Other than that, we have a set of changes on Renesas UDC to make the
code a little easier to read and maintain while also better supporting
extcon framework.
The u_serial adaptation layer learned to use kfifo instead of cooking
its own FIFO implementation.
DWC3 learned to decode a few more USB requests on the trace output.
-----BEGIN PGP SIGNATURE-----
iQJQBAABCgA7FiEElLzh7wn96CXwjh2IzL64meEamQYFAlpTWGYdHGZlbGlwZS5i
YWxiaUBsaW51eC5pbnRlbC5jb20ACgkQzL64meEamQYDsw/4jOBzuVM2A28oCDzd
H9RCagGp4dXpdvLRpueE+L16AA/5MrAI1H1Tdp063Xr+CmlPeMf98JRI5tfBpfn5
8bE6yTojMfvb7vL82kjrnKwKh59IvKVLlFftPBIGJp1uKl5KwWUWMWRcvnpVJHdY
SlZ0U79Pje7RBuq0BkBQ9Lm47pPm5sMqzCyyte4wZbR+6GkAA5W0PBuRes0JLBHo
gUb9h5ns5afrxEdvzUXKpVpd++oP/ZLoZ++jYJ10Z5qSC8+y0DiwRxq7OdOSil+c
BEMKe7I46tGzDFZ2wuMQByHWqCXp7o+9VSf5BYxyP1L58qH1N7M7GyH0Oe+r5xAi
tjFrnL0C8Ax+ouaXLBfmFzv/52BjEqGoqtscWZ4XyVqq98NC1bP5b+qVmIkzXkdv
P7T2lOFZX0ILDX7QXIQbXv71UA/m3bwi3IG0eNX5Rik5xQjDVHnLDpuj87wW1wSH
aUg7sHpggn6GdOICHw9Zry3Z07u3Rab8ThuH0Z4oBI2+3EGhbXTHDjpKYwFYCWEw
nI+9XloOdEkOE6P3S2VO1cQ7YkJ+r4/YRDRvPq3XfLETfxPHwIjqiVeSQWaBA2U8
Om4f/1Oe83jtpfl1T7zL2z08TVPDNMOpE2j4FThA682Pa15emqymRXGDgDmFVizO
boMiMHcP8Wp0MMegK/3RL4syrg==
=uwh/
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v4.16 merge window
Not many changes here, the most important being an improvement for TI's
AM57xx and DRA7xx devices which allows them to disable a metastability
workaround in situations where we know what's going on.
Other than that, we have a set of changes on Renesas UDC to make the
code a little easier to read and maintain while also better supporting
extcon framework.
The u_serial adaptation layer learned to use kfifo instead of cooking
its own FIFO implementation.
DWC3 learned to decode a few more USB requests on the trace output.
v_send_ret_submit() handles urb with a null transfer_buffer, when it
replays a packet with potential malicious data that could contain a
null buffer.
Add a check for the condition when actual_length > 0 and transfer_buffer
is null.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usbip_dump_usb_device() and usbip_dump_urb() print kernel addresses.
Remove kernel addresses from usb device and urb debug msgs and improve
the message content.
Instead of printing parent device and bus addresses, print parent device
and bus names.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Harden CMD_SUBMIT path to handle malicious input that could trigger
large memory allocations. Add checks to validate transfer_buffer_length
and number_of_packets to protect against bad input requesting for
unbounded memory allocations.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trivial fix to spelling mistake in dev_dbg debug message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Calling msg_data_left(&msg) is only useful for its return value,
which in this particular case is ignored.
Fix this by removing such call.
Addresses-Coverity-ID: 1427080
Fixes: 90120d15f4 ("usbip: prevent leaking socket pointer address in messages")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dma_zalloc_coherent for allocating zeroed
memory and remove unnecessary memset function.
Done using Coccinelle.
Generated-by: scripts/coccinelle/api/alloc/kzalloc-simple.cocci
0-day tested with no failures.
Suggested-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds the ELV ALC 8xxx Battery Charging device
to the list of USB IDs of drivers/usb/serial/cp210x.c
Signed-off-by: Christian Holl <cyborgx1@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This patch fix the following build warning:
drivers/usb/musb/musb_host.c:1809:8: warning: variable 'pipe' set but not used [-Wunused-but-set-variable]
by removing the pipe variable in musb_host_rx()
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fix the following warning
drivers/usb/musb/musb_host.c:223:8: warning: variable 'frame' set but not used [-Wunused-but-set-variable]
by remove the frame variable in musb_start_urb().
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add IDs for the OneTouch Verio IQ that comes with an embedded
USB-to-serial converter.
Signed-off-by: Diego Elio Pettenò <flameeyes@flameeyes.eu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Adding phy calibration sequence for USB 3.0 DRD PHY present on
Exynos5420/5800 systems.
This calibration facilitates setting certain PHY parameters viz.
the Loss-of-Signal (LOS) Detector Threshold Level, as well as
Tx-Vboost-Level for Super-Speed operations.
Additionally we also set proper time to wait for RxDetect measurement,
for desired PHY reference clock, so as to solve issue with enumeration
of few USB 3.0 devices, like Samsung SUM-TSB16S 3.0 USB drive
on the controller.
We are using CR_port for this purpose to send required data
to override the LOS values.
On testing with USB 3.0 devices on USB 3.0 port present on
SMDK5420, and peach-pit boards should see following message:
usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd
and without this patch, should see below shown message:
usb 1-1: new high-speed USB device number 2 using xhci-hcd
[Also removed unnecessary extra lines in the register macro definitions]
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
[adapted to use phy_calibrate as entry point]
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
When plugging in a USB webcam I see the following message:
xhci_hcd 0000:04:00.0: WARN Successful completion on short TX: needs
XHCI_TRUST_TX_LENGTH quirk?
handle_tx_event: 913 callbacks suppressed
All is quiet again with this patch (and I've done a fair but of soak
testing with the camera since).
Cc: <stable@vger.kernel.org>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trying to read from debugfs after the system has resumed from
hibernate causes a use-after-free and thus a protection fault.
Steps to reproduce:
Hibernate system, resume from hibernate, then run
$ cat /sys/kernel/debug/usb/xhci/*/command-ring/enqueue
[ 3902.765086] general protection fault: 0000 [#1] PREEMPT SMP
...
[ 3902.765136] RIP: 0010:xhci_trb_virt_to_dma.part.50+0x5/0x30
...
[ 3902.765178] Call Trace:
[ 3902.765188] xhci_ring_enqueue_show+0x1e/0x40
[ 3902.765197] seq_read+0xdb/0x3a0
[ 3902.765204] ? __handle_mm_fault+0x5fb/0x1210
[ 3902.765211] full_proxy_read+0x4a/0x70
[ 3902.765219] __vfs_read+0x23/0x120
[ 3902.765228] vfs_read+0x8e/0x130
[ 3902.765235] SyS_read+0x42/0x90
[ 3902.765242] do_syscall_64+0x6b/0x290
[ 3902.765251] entry_SYSCALL64_slow_path+0x25/0x25
The issue is caused by the xhci ring structures being reallocated
when the system is resumed, but pointers to the old structures
being retained in the debugfs files "private" field:
The proposed patch fixes this issue by storing a pointer to the xhci_ring
field in the xhci device structure in debugfs rather than directly
storing a pointer to the xhci_ring.
Fixes: 02b6fdc2a1 ("usb: xhci: Add debugfs interface for xHCI driver")
Signed-off-by: Alexander Kappner <agk@godking.net>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Free the virt_device and its debugfs_private member together.
When resuming from hibernate the .free_dev callback unconditionally
freed the debugfs_private member, but could leave virt_device intact.
This triggered a NULL pointer dereference after resume when usbmuxd
sent a USBDEVFS_SETCONFIGURATION ioctl to a device, trying to add a
endpoint debugfs entry to a already freed debugfs_private pointer.
Fixes: 02b6fdc2a1 ("usb: xhci: Add debugfs interface for xHCI driver")
Reported-by: Alexander Kappner <agk@godking.net>
Tested-by: Alexander Kappner <agk@godking.net>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some new device ids for ftdi_sio, option and qcserial.
Note that the qcserial patch enables the SetControlLineState request
(used to raise DTR/RTS) for the GPS interface of all devices using the
Sierra Wireless layout. This was required for the Sierra Wireless EM7565
and has been tested using several other modems as well.
All but the final commit have been in linux-next without any reported
issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=Qx6D
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.15-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes
USB-serial fixes for v4.15-rc6
Here are some new device ids for ftdi_sio, option and qcserial.
Note that the qcserial patch enables the SetControlLineState request
(used to raise DTR/RTS) for the GPS interface of all devices using the
Sierra Wireless layout. This was required for the Sierra Wireless EM7565
and has been tested using several other modems as well.
All but the final commit have been in linux-next without any reported
issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
USB Ethernet gadget now works on Tegra30.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaONRxAAoJEEhZKYFQ1nG7eGsH/jW+VX14utmEXt3CHFkTAmL8
gDUM/74opMiZVLSDDV+J/CFcNASj9Qk5X39928Y69x731b82yIR56Fmi4WOGX4m5
YD6JaMfgx0sTT76c07SUJYVkJCfI41NwR/YSJH79Mghy3Osuv40koh+DPTGQhjPY
XjvfxIxwmsLvz7cMkTfIEOud4axaKpxvm/NOlwdCSrtGzp9G4GEcIpwz1MYpqaA/
Fnx60cqmiGG+vFuMjnwo+5bpSXpEWuIFfJujZwU0h7vLqqUMd8WwkHp92JnBr4+H
jwgIZfC2adK4iLd/VvprVle3k8TY1L6oI4EjD7l1+Kge1q94B/I7Ubd7gvy6XmA=
=2wh+
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-linus
Peter writes:
One fix for ulpi-node lookup at msm glue driver
Commit e0429362ab
("usb: Add device quirk for Logitech HD Pro Webcams C920 and C930e")
introduced quirk to workaround an issue with some Logitech webcams.
There is one more model that has the same issue - C925e, so applying
the same quirk as well.
See aforementioned commit message for detailed explanation of the problem.
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This modem needs this quirk to operate. It produces timeouts when
resumed without reset.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usbip driver is leaking socket pointer address in messages. Remove
the messages that aren't useful and print sockfd in the ones that
are useful for debugging.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB 3.1 devices are not detected as 3.1 capable since 4.15-rc3 due to a
off by one in commit 81cf4a4536 ("USB: core: Add type-specific length
check of BOS descriptors")
It uses USB_DT_USB_SSP_CAP_SIZE() to get SSP capability size which takes
the zero based SSAC as argument, not the actual count of sublink speed
attributes.
USB3 spec 9.6.2.5 says "The number of Sublink Speed Attributes = SSAC + 1."
The type-specific length check patch was added to stable and needs to be
fixed there as well
Fixes: 81cf4a4536 ("USB: core: Add type-specific length check of BOS descriptors")
Cc: linux-stable <stable@vger.kernel.org>
CC: Masakazu Mokuno <masakazu.mokuno@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clear Feature Endpoint Halt should reset the data toggle even if the
endpoint isn't halted. Host should manage to clear the host side data
toggle to keep in sync with the device.
Test by sending a "3 data packet URB" before and after clearing the halt.
this should create a toggle sequence with two consecutive DATA0 packets.
A successful test sequence looks like this
ClearFeature(ENDPOINT_HALT) - initial toggle clear
DATA0 (max packet sized)
DATA1 (max packet sized)
DATA0 (zero length packet)
ClearFeature(ENDPOINT_HALT) - resets toggle
DATA0 (max packet sized), if clear halt fails then toggle is DATA1
DATA1 (max packet sized)
DATA0 (zero length packet)
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB SS and SSP hubs provide wHubDelay values on their hub descriptor
which we should inform the USB Device about.
The USB Specification 3.0 explains, on section 9.4.11, how to
calculate the value and how to issue the request. Note that a
USB_REQ_SET_ISOCH_DELAY is valid on all device states (Default,
Address, Configured), we just *chose* to issue it from Address state
right after successfully fetching the USB Device Descriptor.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for PID 0x1101 of Telit ME910.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
According to drivers/usb/serial/io_edgeport.c, the driver may sleep
under a spinlock.
The function call path is:
edge_bulk_in_callback (acquire the spinlock)
process_rcvd_data
process_rcvd_status
change_port_settings
send_iosp_ext_cmd
write_cmd_usb
usb_kill_urb --> may sleep
To fix it, the redundant usb_kill_urb() is removed from the error path
after usb_submit_urb() fails.
This possible bug is found by my static analysis tool (DSAC) and checked
by my code review.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This patch adds extcon notifier callback to set the mode of
host/peripheral by using extcon state (e.g phy-rcar-gen3-usb2) for
non-otg channel (e.g. R-Car D3).
[Fengguang Wu: fixed sparse warning]
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
usb: renesas_usbhs: usbhs_rcar3_notifier() can be static
Fixes: 3a7cce26122e ("usb: renesas_usbhs: add extcon notifier to set mode for non-otg channel")
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
A malicious USB device with crafted descriptors can cause the kernel
to access unallocated memory by setting the bNumInterfaces value too
high in a configuration descriptor. Although the value is adjusted
during parsing, this adjustment is skipped in one of the error return
paths.
This patch prevents the problem by setting bNumInterfaces to 0
initially. The existing code already sets it to the proper value
after parsing is complete.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 32fd87b3bb.
Alan wrote a better fix for this...
Cc: Andrey Konovalov <andreyknvl@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usbhs_rcar3_power_and_pll_ctrl() will be used by non-otg channel
(e.g. R-Car D3) and the previous code has hardcoded as peripheral mode.
So, this patch sets the mode by using extcon state.
If the channel doesn't get any extcon devices, this driver's behavior
is the same as before.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
To cleanup the code, this patch adds a function to write the UGCTRL2
register.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
On rk3288-veyron devices on Chrome OS it was found that plugging in an
Arduino-based USB device could cause the system to lockup, especially
if the CPU Frequency was at one of the slower operating points (like
100 MHz / 200 MHz).
Upon tracing, I found that the following was happening:
* The USB device (full speed) was connected to a high speed hub and
then to the rk3288. Thus, we were dealing with split transactions,
which is all handled in software on dwc2.
* Userspace was initiating a BULK IN transfer
* When we sent the SSPLIT (to start the split transaction), we got an
ACK. Good. Then we issued the CSPLIT.
* When we sent the CSPLIT, we got back a NAK. We immediately (from
the interrupt handler) started to retry and sent another SSPLIT.
* The device kept NAKing our CSPLIT, so we kept ping-ponging between
sending a SSPLIT and a CSPLIT, each time sending from the interrupt
handler.
* The handling of the interrupts was (because of the low CPU speed and
the inefficiency of the dwc2 interrupt handler) was actually taking
_longer_ than it took the other side to send the ACK/NAK. Thus we
were _always_ in the USB interrupt routine.
* The fact that USB interrupts were always going off was preventing
other things from happening in the system. This included preventing
the system from being able to transition to a higher CPU frequency.
As I understand it, there is no requirement to retry super quickly
after a NAK, we just have to retry sometime in the future. Thus one
solution to the above is to just add a delay between getting a NAK and
retrying the transmission. If this delay is sufficiently long to get
out of the interrupt routine then the rest of the system will be able
to make forward progress. Even a 25 us delay would probably be
enough, but we'll be extra conservative and try to delay 1 ms (the
exact amount depends on HZ and the accuracy of the jiffy and how close
the current jiffy is to ticking, but could be as much as 20 ms or as
little as 1 ms).
Presumably adding a delay like this could impact the USB throughput,
so we only add the delay with repeated NAKs.
NOTE: Upon further testing of a pl2303 serial adapter, I found that
this fix may help with problems there. Specifically I found that the
pl2303 serial adapters tend to respond with a NAK when they have
nothing to say and thus we end with this same sequence.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.
Note that the original premature free of the parent node has already
been fixed separately, but that fix was apparently never backported to
stable.
Fixes: 47654a1620 ("usb: chipidea: msm: Restore wrapper settings after reset")
Fixes: b74c43156c ("usb: chipidea: msm: ci_hdrc_msm_probe() missing of_node_get()")
Cc: stable <stable@vger.kernel.org> # 4.10: b74c43156c
Cc: Stephen Boyd <stephen.boyd@linaro.org>
Cc: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Function xhci_dbc_free_req is local to the source and does not need to
be in global scope, so make it static.
Cleans up sparse warning:
symbol 'xhci_dbc_free_req' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Incorrect size was given to memset when zeroing the DbC endpoint
structures on exit. Use element size * ARRAY_SIZE to fix it
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Fixes: dfba2174dc ("usb: xhci: Add DbC support in xHCI driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The URB_NO_FSBR flag has never really been used. It was introduced as
a potential way for UHCI to minimize PCI bus usage (by not attempting
full-speed bulk and control transfers more than once per frame), but
the flag was not set by any drivers.
There's no point in keeping it around. This patch simplifies the API
by removing it. Unfortunately, it does have to be kept as part of the
usbfs ABI, but at least we can document in
include/uapi/linux/usbdevice_fs.h that it doesn't do anything.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB Power Delivery Specification (v3.0) dictates in ch.
6.4.1 - Capabilities Message - that the vSafe5V Fixed Supply
Object shall always be the first object. tcpm.c now checks
that this rule is obeyed (commit 5007e1b5db "typec: tcpm
Validate source and sink caps"), and that makes the
typec_wcove.c fail to probe. The voltage is higher then what
is permitted for the vSafe5V parameter.
Dropping the voltage in the first Fixed Supply object of the
sink capabilities down to 5V, and maximum current down to
500mA, making the driver probe successfully again.
Also, removing the Battery and Variable Supply objects, as
there is no need for them.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When cleaning up the configurations, make sure we only free the number
of configurations and interfaces that we could have allocated.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have a few fixes on dwc3:
- one fix which only happens with some implementations where we need to
wait longer for some commands to finish.
- Another fix for high-bandwidth isochronous endpoint programming making
sure that we send the correct DATA tokens in the correct sequence
- A couple PM fixes on dwc3-of-simple
The other synopsys controller driver (dwc2) got a fix for FIFO size
programming.
Other than these, we have a couple Kconfig fixes making sure that
dependencies are properly setup.
-----BEGIN PGP SIGNATURE-----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=6T1G
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.15-rc4
We have a few fixes on dwc3:
- one fix which only happens with some implementations where we need to
wait longer for some commands to finish.
- Another fix for high-bandwidth isochronous endpoint programming making
sure that we send the correct DATA tokens in the correct sequence
- A couple PM fixes on dwc3-of-simple
The other synopsys controller driver (dwc2) got a fix for FIFO size
programming.
Other than these, we have a couple Kconfig fixes making sure that
dependencies are properly setup.
The dwc2 USB controller in Stratix10 has an additional ECC reset bit that
needs to get de-asserted in order for the controller to work properly.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch uses usbhs_pipe_clear_without_sequence() instead of
usbhsf_fifo_clear() because usbhsf_fifo_clear() may not clear the pipe
buffer completely. This patch also changes the clearing condition from
DMA only to both DMA and PIO.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds usbhs_pipe_clear_without_sequence() function.
The controller has the pipe buffer and the PIPEnCTR.ACLRM can clear
it completely. But, it's also clear the data sequence. So, the driver
needs to get the sequence before.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The datasheet doesn't mention that needs to poll of FRDY is set or not.
So, this patch removes such handling in the usbhsf_fifo_barrier().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Factor out the guts of usb charger initialization into usb_charger_init()
function, to make the usb_add_extcon() only do the extcon related things.
Meanwhile we also should initialize the USB charger before registering
the extcon device, in case the extcon notification was issued earlier than
usb charger initialization.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This reverts commit 7a9618a22a.
Romain Izard recently reported that commit 7a9618a22a ended up
allowing every legacy gadget driver to statically linked to the
kernel, however that doesn't work, since only one legacy gadget can be
bound to a controller. Because of that, let's revert the original commit
and fix the problem.
Reported-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Configuring the USB_G_WEBCAM driver as built-in leads to a link
error when CONFIG_VIDEO_V4L2 is a loadable module:
drivers/usb/gadget/function/f_uvc.o: In function `uvc_function_setup':
f_uvc.c:(.text+0xfe): undefined reference to `v4l2_event_queue'
drivers/usb/gadget/function/f_uvc.o: In function `uvc_function_ep0_complete':
f_uvc.c:(.text+0x188): undefined reference to `v4l2_event_queue'
This changes the Kconfig dependency to disallow that configuration,
and force it to be a module in that case as well.
This is apparently a rather old bug, but very hard to trigger
even in thousands of randconfig builds.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some platforms (e.g. TI's DRA7 USB2 instance) have more trouble
with the metastability workaround as it supports only
a High-Speed PHY and the PHY can enter into an Erratic state [1]
when the controller is set in SuperSpeed mode as part of
the metastability workaround.
This causes upto 2 seconds delay in enumeration on DRA7's USB2
instance in gadget mode.
If these platforms can be better off without the workaround,
provide a device tree property to suggest that so the workaround
is avoided.
[1] Device mode enumeration trace showing PHY Erratic Error.
irq/90-dwc3-969 [000] d... 52.323145: dwc3_event: event (00000901): Erratic Error [U0]
irq/90-dwc3-969 [000] d... 52.560646: dwc3_event: event (00000901): Erratic Error [U0]
irq/90-dwc3-969 [000] d... 52.798144: dwc3_event: event (00000901): Erratic Error [U0]
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The UDC core ensures that .udc_set_speed() is called with
a speed that is a minimum of the max speeds supported
by the gadget function driver and the UDC driver.
We can now use the speed argument as is.
Get rid of the debug print as that condition will never happen.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There will never be a case when gadget.speed isn't already
USB_SPEED_FULL if connection is not USB-3 and gadget.speed
is not USB_SPEED_HIGH or USB_SPEED_LOW.
Remove the unnecessary code.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a jump target so that a specific error message is stored only once
at the end of this function implementation.
Replace two calls of the function "dev_err" by goto statements.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Variable is_short is set to zero but this value is never read as it is
overwritten with a new value later on, hence it is a redundant
assignment and can be removed. Pointer dev is assigned a value that
is not read and it is updated a few statements later, this too is
redundant and can be removed. Cleans up clan warnings:
drivers/usb/gadget/udc/pxa27x_udc.c:986:3: warning: Value stored
to 'is_short' is never read
drivers/usb/gadget/udc/pxa27x_udc.c:1141:2: warning: Value stored
to 'dev' is never read
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Pointer udc is assigned but never read, hence it is redundant and
can be removed. Cleans up clang warning:
drivers/usb/gadget/udc/udc-xilinx.c:974:2: warning: Value stored
to 'udc' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The variable value is being assigned to zero but that value is never being
read. Either value is being reassigned in the following if condition, or
it is never read and the function returns. In both cases the assignment is
redundant and can be removed. Cleans up clang warning:
drivers/usb/gadget/legacy/inode.c:1473:4: warning: Value stored to 'value'
is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Trival fix to spelling mistake in ERR message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Silences the following warnings:
drivers/usb/gadget/function/f_fs.c:1253:37: warning: incorrect type in argument 1 (different address spaces)
drivers/usb/gadget/function/f_fs.c:1253:37: expected void [noderef] <asn:1>*to
drivers/usb/gadget/function/f_fs.c:1253:37: got void *<noident>
drivers/usb/gadget/function/f_fs.c:2322:23: warning: cast to restricted __le32
drivers/usb/gadget/function/f_fs.c:2876:38: warning: cast to restricted __le32
drivers/usb/gadget/function/f_fs.c:272:12: warning: context imbalance in '__ffs_ep0_queue_wait' - unexpected unlock
drivers/usb/gadget/function/f_fs.c:450:17: warning: context imbalance in 'ffs_ep0_write' - different lock contexts for basic block
drivers/usb/gadget/function/f_fs.c:490:24: warning: context imbalance in '__ffs_ep0_read_events' - unexpected unlock
drivers/usb/gadget/function/f_fs.c:496:16: warning: context imbalance in 'ffs_ep0_read' - different lock contexts for basic block
Also, add an "unlocks spinlock" comment for consistency with existing ones.
No behaviour change is intended.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The kernel FIFO implementation, kfifo, provides interfaces to manipulate
a first-in-first-out circular buffer. Use kfifo instead of the homemade
one to make the code more concise and readable.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fixes the following warnings:
drivers/usb/dwc3/io.h:43:31: warning: incorrect type in argument 1 (different address spaces)
drivers/usb/dwc3/io.h:43:31: expected void *base
drivers/usb/dwc3/io.h:43:31: got void [noderef] <asn:2>*
drivers/usb/dwc3/io.h:62:32: warning: incorrect type in argument 1 (different address spaces)
drivers/usb/dwc3/io.h:62:32: expected void *base
drivers/usb/dwc3/io.h:62:32: got void [noderef] <asn:2>*
This fixes the noisiest ones as they get emitted multiple times.
A few warnings remain, for which the proper fix is less clear.
No behaviour change is expected.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of keeping our own isoch_delay, let's make use of the newly
introduced isoch_delay member in struct usb_gadget. The benefit here
is that we would be using a generic "API" which other UDCs can use,
resulting in a common setup for gadget drivers who may be interested
in Isoch Delay value.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In host mode reading from DPTXSIZn returning invalid value in
dwc2_check_param_tx_fifo_sizes function.
In total TxFIFO size calculations unnecessarily reducing by ep_info.
hw->total_fifo_size can be fully allocated for FIFO's.
Added num_dev_in_eps member in dwc2_hw_params structure to save number
of IN EPs.
Added g_tx_fifo_size array in dwc2_hw_params structure to store power
on reset values of DPTXSIZn registers in forced device mode.
Updated dwc2_hsotg_tx_fifo_count() function to get TxFIFO count from
num_dev_in_eps.
Updated dwc2_get_dev_hwparams() function to store DPTXFSIZn in
g_tx_fifo_size array.
dwc2_get_host/dev_hwparams() functions call moved after num_dev_in_eps
set from hwcfg4.
Modified dwc2_check_param_tx_fifo_sizes() function to check TxFIFOn
sizes based on g_tx_fifo_size array.
Removed ep_info subtraction during calculation of tx_addr_max in
dwc2_hsotg_tx_fifo_total_depth() function. Also removed
dwc2_hsotg_ep_info_size() function as no more need.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For isochronous endpoints with ep->mult less than 3, PCM1 value of
trb->size in set incorrectly.
For ep->mult = 2, this is set to 0/-1 and for ep->mult = 1, this is
set to -2. This is because the initial mult is set to ep->mult - 1
instead of 2.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc3_of_simple_dev_pm_ops has never been used since the initial support
by commit 16adc674d0 ("usb: dwc3: add generic OF glue layer").
I guess it just missed to set .pm struct member.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If of_clk_get() fails, the clean-up of already initialized clocks should be
the same as when clk_prepare_enable() fails. Thus a clk_disable_unprepare()
for each clock should be called before the clk_put().
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 16adc674d0 ("usb: dwc3: ep0: fix setup_packet_pending initialization")
Signed-off-by: Andreas Platschek <andreas.platschek@opentech.at>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For MTK's xHCI 1.0 or latter, TD size is the number of max
packet sized packets remaining in the TD, not including
this TRB (following spec).
For MTK's xHCI 0.96 and older, TD size is the number of max
packet sized packets remaining in the TD, including this TRB
(not following spec).
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid null pointer dereference if some function is walking through the
devs array accessing members of a new virt_dev that is mid allocation.
Add the virt_dev to xhci->devs[i] _after_ the virt_device and all its
members are properly allocated.
issue found by KASAN: null-ptr-deref in xhci_find_slot_id_by_port
"Quick analysis suggests that xhci_alloc_virt_device() is not mutex
protected. If so, there is a time frame where xhci->devs[slot_id] is set
but not fully initialized. Specifically, xhci->devs[i]->udev can be NULL."
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trace the port status of each port of a roothub when
the xhci roothub receives a Get Hub Status request.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add tracing showing the port status register content each time
the xhci roothub receives a Get Port Status request.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xHCI driver currently has the IMOD set to 160, which
translates to an IMOD interval of 40,000ns (160 * 250)ns
Commit 0cbd4b34cd ("xhci: mediatek: support MTK xHCI host controller")
introduced a QUIRK for the MTK platform to adjust this interval to 20,
which translates to an IMOD interval of 5,000ns (20 * 250)ns. This is
due to the fact that the MTK controller IMOD interval is 8 times
as much as defined in xHCI spec.
Instead of adding more quirk bits for additional platforms, this patch
introduces the ability for vendors to set the IMOD_INTERVAL as is
optimal for their platform. By using device_property_read_u32() on
"imod-interval-ns", the IMOD INTERVAL can be specified in nano seconds.
If no interval is specified, the default of 40,000ns (IMOD=160) will be
used.
No bounds checking has been implemented due to the fact that a vendor
may have violated the spec and would need to specify a value outside of
the max 8,000 IRQs/second limit specified in the xHCI spec.
Tested-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Adam Wallis <awallis@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Each event segment has been exposed through debugfs. There is no
need to dump ERST content with printk in code. Remove it to make
code more concise and readable.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The content of each register has been exposed through debugfs.
There is no need to dump register content with printk in code
lines. Remove them to make code more concise and readable.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xHCI compatible USB host controllers(i.e. super-speed USB3 controllers)
can be implemented with the Debug Capability(DbC). It presents a debug
device which is fully compliant with the USB framework and provides the
equivalent of a very high performance full-duplex serial link. The debug
capability operation model and registers interface are defined in 7.6.8
of the xHCI specification, revision 1.1.
The DbC debug device shares a root port with the xHCI host. By default,
the debug capability is disabled and the root port is assigned to xHCI.
When the DbC is enabled, the root port will be assigned to the DbC debug
device, and the xHCI sees nothing on this port. This implementation uses
a sysfs node named <dbc> under the xHCI device to manage the enabling
and disabling of the debug capability.
When the debug capability is enabled, it will present a debug device
through the debug port. This debug device is fully compliant with the
USB3 framework, and it can be enumerated by a debug host on the other
end of the USB link. As soon as the debug device is configured, a TTY
serial device named /dev/ttyDBC0 will be created.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch makes some static functions global to avoid duplications
in different files. These functions can be used in the implementation
of xHCI debug capability. There is no functional change.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commands with input contexts are allocated with the
xhci_alloc_command_with_ctx helper.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a xhci_alloc_command_with_ctx() helper to get rid of
one of the boolean parameters telling if a context should
be allocated with the command.
No functional changes, improves core readability
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the build warning about variable 'ep_ring' set but not used
[Minor commit message change -Mathias]
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the build warning: variable 'urb_priv' set but not used
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the build warning: variable 'ep' set but not used
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the build warning about variable 'last_freed_endpoint'
set but not used [-Wunused-but-set-variable]
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
stub_send_ret_submit() handles urb with a potential null transfer_buffer,
when it replays a packet with potential malicious data that could contain
a null buffer. Add a check for the condition when actual_length > 0 and
transfer_buffer is null.
Reported-by: Secunia Research <vuln@secunia.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a client has a USB device attached over IP, the vhci_hcd driver is
locally leaking a socket pointer address via the
/sys/devices/platform/vhci_hcd/status file (world-readable) and in debug
output when "usbip --debug port" is run.
Fix it to not leak. The socket pointer address is not used at the moment
and it was made visible as a convenient way to find IP address from socket
pointer address by looking up /proc/net/{tcp,tcp6}.
As this opens a security hole, the fix replaces socket pointer address with
sockfd.
Reported-by: Secunia Research <vuln@secunia.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Harden CMD_SUBMIT path to handle malicious input that could trigger
large memory allocations. Add checks to validate transfer_buffer_length
and number_of_packets to protect against bad input requesting for
unbounded memory allocations. Validate early in get_pipe() and return
failure.
Reported-by: Secunia Research <vuln@secunia.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
get_pipe() routine doesn't validate the input endpoint number
and uses to reference ep_in and ep_out arrays. Invalid endpoint
number can trigger BUG(). Range check the epnum and returning
error instead of calling BUG().
Change caller stub_recv_cmd_submit() to handle the get_pipe()
error return.
Reported-by: Secunia Research <vuln@secunia.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is another JMS567-based USB3 UAS enclosure (152d:0578) that fails
with the following error:
[sda] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[sda] tag#0 Sense Key : Illegal Request [current]
[sda] tag#0 Add. Sense: Invalid field in cdb
The issue occurs both with UAS (occasionally) and mass storage
(immediately after mounting a FS on a disk in the enclosure).
Enabling US_FL_BROKEN_FUA quirk solves this issue.
This patch adds an UNUSUAL_DEV with US_FL_BROKEN_FUA for the enclosure
for both UAS and mass storage.
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When babble condition happens, the musb controller might automatically
turns off VBUS. On DA8xx platform, the controller generates drvvbus
interrupt for turning off VBUS along with the babble interrupt.
In this case, we should handle the babble interrupt first and recover
from the babble condition.
This change ignores the drvvbus interrupt if babble interrupt is also
generated at the same time, so the babble recovery routine works
properly.
Cc: stable@vger.kernel.org # v3.16+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At present, TCPM code assumes that local device supports
variable/batt pdos and always selects the pdo with highest
possible power within the board limit. This assumption
might not hold good for all devices. To overcome this,
this patch makes TCPM only accept a source_pdo when there is
a matching sink pdo.
For Fixed pdos: The voltage should match between the
incoming source_cap and the registered snk_pdo
For Variable/Batt pdos: The incoming source_cap voltage
range should fall within the registered snk_pdo's voltage
range.
Also, when the cap_mismatch bit is set, the max_power/current
should be set to the max_current/power of the sink_pdo.
This is according to:
"If the Capability Mismatch bit is set to one
The Maximum Operating Current/Power field may contain a value
larger than the maximum current/power offered in the Source
Capabilities message’s PDO as referenced by the Object position field.
This enables the Sink to indicate that it requires more current/power
than is being offered. If the Sink requires a different voltage this
will be indicated by its Sink Capabilities message.
Signed-off-by: Badhri Jagan Sridharan <Badhri@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The source and sink caps should follow the following rules.
This patch validates whether the src_caps/snk_caps adheres
to it.
6.4.1 Capabilities Message
A Capabilities message (Source Capabilities message or Sink
Capabilities message) shall have at least one Power
Data Object for vSafe5V. The Capabilities message shall also
contain the sending Port’s information followed by up to
6 additional Power Data Objects. Power Data Objects in a
Capabilities message shall be sent in the following order:
1. The vSafe5V Fixed Supply Object shall always be the first object.
2. The remaining Fixed Supply Objects, if present, shall be sent
in voltage order; lowest to highest.
3. The Battery Supply Objects, if present shall be sent in Minimum
Voltage order; lowest to highest.
4. The Variable Supply (non-battery) Objects, if present, shall be
sent in Minimum Voltage order; lowest to highest.
Errors in source/sink_caps of the local port will prevent
the port registration. Whereas, errors in source caps of partner
device would only log them.
Signed-off-by: Badhri Jagan Sridharan <Badhri@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This corrects the endpiont type value set to the DbC bulk in endpoint.
The previous value doesn't cause any problems because that we now only
use the bulk out endpoint. Set the hardware with the correct value any
way.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 7fee72d5e8 ("uas: Always apply US_FL_NO_ATA_1X quirk to
Seagate devices"), the US_FL_NO_ATA_1X is always set for Seagate devices,
so the per device unusual_uas.h entries for Seagate devices can be
removed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replacing dma_pool_alloc and memset with a single call to dma_pool_zalloc
Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Interface drivers like btusb that don't support reset-resume will be
rebound at resume if port was reset. Rebind is done during the pm_ops
.complete callback when probe returns EPROBE_DEFER as default.
Remove the "rebind failed: -517" message.
Device probe will eventually take place later.
[one-liner by Jerry Snitselaar posted in a mailing list question -Mathias]
Suggested-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fix of "FIXME: Notify the subdrivers..." doesn't actually have any
real effect. The "FIXME" changed to simple comment.
Signed-off-by: Mikhail Zaytsev <flashed@mail.ru>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These duplicate includes have been found with scripts/checkincludes.pl but
they have been removed manually to avoid removing false positives.
Signed-off-by: Pravin Shedge <pravin.shedge4linux@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using a period after a newline causes bad output.
Miscellanea:
o Coalesce formats too
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xHC can generate two events for a short transfer if the short TRB and
last TRB in the TD are not the same TRB.
The driver will handle the TD after the first short event, and remove
it from its internal list. Driver then incorrectly prints a warning
for the second event:
"WARN Event TRB for slot x ep y with no TDs queued"
Fix this by not printing a warning if we get a event on a empty list
if the previous event was a short event.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The previous USB3 SuperSpeed enabling patches mistakenly enabled
URB scatter-gather chaining, which is actually not supported by
the VHCI HCD. This patch fixes that.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=197867
Fixes: 03cd00d538 ("usbip: vhci-hcd: Set the vhci structure up to work")
Reported-by: Juan Zea <juan.zea@qindel.com>
Signed-off-by: Yuyang Du <yuyang.du@intel.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After a long time, we finally have a good solution for how to handle
OS descriptor on FFS. From now on we will force the Reserved field to
be 1 as mandated by the specification.
Apart from that, we have a couple other smaller fixes:
- FFS learned to not sleep in atomic context.
- UDC-core has a fix for the way we set a UDC's operating speed.
- Renesas USB3 has a fix for the maximum number of pipes supported
- Allow legacy drivers to be compiled without USB_ETH
- Fix some coccinelle warnings
-----BEGIN PGP SIGNATURE-----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=hBSF
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.15-rc2
After a long time, we finally have a good solution for how to handle
OS descriptor on FFS. From now on we will force the Reserved field to
be 1 as mandated by the specification.
Apart from that, we have a couple other smaller fixes:
- FFS learned to not sleep in atomic context.
- UDC-core has a fix for the way we set a UDC's operating speed.
- Renesas USB3 has a fix for the maximum number of pipes supported
- Allow legacy drivers to be compiled without USB_ETH
- Fix some coccinelle warnings
Here are some new device ids.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=xcVp
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.15-rc2' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.15-rc2
Here are some new device ids.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
We've been adding this as a quirk on a per device basis hoping that
newer disk enclosures would do better, but that has not happened,
so simply apply this quirk to all Seagate devices.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KY-688 USB 3.1 Type-C Hub internally uses a Genesys Logic hub to connect
to Realtek r8153.
Similar to commit ("7496cfe5431f2 usb: quirks: Add no-lpm quirk for Moshi
USB to Ethernet Adapter"), no-lpm can make r8153 ethernet work.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes the USB device gets confused about the state of the initialization and
the connection fails. In particular, the device thinks that it's already set up
and running while the host thinks the device still needs to be configured. To
work around this issue, power-cycle the hub's output to issue a sort of "reset"
to the device. This makes the device restart its state machine and then the
initialization succeeds.
This fixes problems where the kernel reports a list of errors like this:
usb 1-1.3: device not accepting address 19, error -71
The end result is a non-functioning device. After this patch, the sequence
becomes like this:
usb 1-1.3: new high-speed USB device number 18 using ci_hdrc
usb 1-1.3: device not accepting address 18, error -71
usb 1-1.3: new high-speed USB device number 19 using ci_hdrc
usb 1-1.3: device not accepting address 19, error -71
usb 1-1-port3: attempt power cycle
usb 1-1.3: new high-speed USB device number 21 using ci_hdrc
usb-storage 1-1.3:1.2: USB Mass Storage device detected
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As most of BOS descriptors are longer in length than their header
'struct usb_dev_cap_header', comparing solely with it is not sufficient
to avoid out-of-bounds access to BOS descriptors.
This patch adds descriptor type specific length check in
usb_get_bos_descriptor() to fix the issue.
Signed-off-by: Masakazu Mokuno <masakazu.mokuno@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable temp is incorrectly being updated, instead it should
be offset otherwise the loop just reads the same capability value
and loops forever. Thanks to Alan Stern for pointing out the
correct fix to my original fix. Fix also cleans up clang warning:
drivers/usb/host/ehci-dbg.c:840:4: warning: Value stored to 'temp'
is never read
Fixes: d49d431744 ("USB: misc ehci updates")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix bus-node lookup during registration, which ended up searching the whole
device tree depth-first starting at the parent (or grand parent) rather
than just matching on its children.
To make things worse, the parent (or grand-parent) node could end being
prematurely freed as well.
Fixes: ef6a7bcfb0 ("usb: ulpi: Support device discovery via DT")
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Reported-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: stable <stable@vger.kernel.org> # 4.10
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USBDEVFS_URB_ISO_ASAP must be accepted only for ISO endpoints.
Improve sanity checking.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is more clear from user perspective to wrap the whole USB
Type-C support under a single option that the user can
select, then it is to always ask the user for every USB
Type-C and USB Power Delivery driver separately.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up the USB device-node helper that is used to look up a device
node given a parent hub device and a port number. Also pass in a struct
usb_device as first argument to provide some type checking.
Give the helper the more descriptive name usb_of_get_device_node(),
which matches the new usb_of_get_interface_node() helper that is used to
look up a second type of of child node from a USB device.
Note that the terms "device node" and "interface node" are defined and
used by the OF Recommended Practice for USB.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This code looks up a USB device node from a given parent USB device but
never dropped its reference to the returned node.
As only the address of the node is used for a later matching, the
reference can be dropped immediately.
Note that this trigger implementation confuses the description of the
USB device connected to a port with the port itself (which does not have
a device-tree representation).
Fixes: 4f04c210d0 ("usb: core: read USB ports from DT in the usbport LED trigger driver")
Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add OF device-tree support for USB interfaces.
USB "interface nodes" are children of USB "device nodes" and are
identified by an interface number and a configuration value:
&usb1 { /* host controller */
dev1: device@1 { /* device at port 1 */
compatible = "usb1234,5678";
reg = <1>;
#address-cells = <2>;
#size-cells = <0>;
interface@0,2 { /* interface 0 of configuration 2 */
compatible = "usbif1234,5678.config2.0";
reg = <0 2>;
};
};
};
The configuration component is not included in the textual
representation of an interface-node unit address for configuration 1:
&dev1 {
interface@0 { /* interface 0 of configuration 1 */
compatible = "usbif1234,5678.config1.0";
reg = <0 1>;
};
};
When a USB device of class 0 or 9 (hub) has only a single configuration
with a single interface, a special case "combined node" is used instead
of a device node with an interface node:
&usb1 {
device@2 {
compatible = "usb1234,abcd";
reg = <2>;
};
};
Combined nodes are shared by the two device structures representing the
USB device and its interface in the kernel's device model.
Note that, as for device nodes, the compatible strings for interface
nodes are currently not used.
For more details see "Open Firmware Recommended Practice: Universal
Serial Bus Version 1" and the binding documentation.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The expectation in the FUSB302 driver is that a TX_SUCCESS event
should occur after a message has been sent, but before a GCRCSENT
event is raised to indicate successful receipt of a message from
the partner. However in some circumstances it is possible to see
the hardware raise a GCRCSENT event before a TX_SUCCESS event
is raised. The upshot of this is that the GCRCSENT handling portion
of code ends up reporting the GoodCRC message to TCPM because the
TX_SUCCESS event hasn't yet arrived to trigger a consumption of it.
When TX_SUCCESS is then raised by the chip it ends up consuming the
actual message that was meant for TCPM, and this incorrect sequence
results in a hard reset from TCPM.
To avoid this problem, this commit updates the message reading
code to check whether a GoodCRC message was received or not. Based
on this check it will either report that the previous transmission
has completed or it will pass the msg data to TCPM for futher
processing. This way the incorrect ordering of the events no longer
matters.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If probe fails, fusb302_debugfs_exit is called making it impossible
to view any logs so use normal dev_err for any error messages during
probe.
Signed-off-by: Mats Karrman <mats.dev.list@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trivial fix to spelling mistake in error message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable t is assigned but never read, it is redundant and therefore
can be removed. Cleans up clang warning:
drivers/usb/host/whci/asl.c:106:3: warning: Value stored to 't' is
never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB devices should work just fine when they don't support language id.
Lower the log level so user won't panic in the future.
BugLink: https://bugs.launchpad.net/bugs/1729618
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The specification says that the Reserved1 field in OS_DESC_EXT_COMPAT
must have the value "1", but when this feature was first implemented we
rejected any non-zero values.
This was adjusted to accept all non-zero values (while now rejecting
zero) in commit 53642399aa ("usb: gadget: f_fs: Fix wrong check on
reserved1 of OS_DESC_EXT_COMPAT"), but that breaks any userspace
programs that worked previously by returning EINVAL when Reserved1 == 0
which was previously the only value that succeeded!
If we just set the field to "1" ourselves, both old and new userspace
programs continue to work correctly and, as a bonus, old programs are
now compliant with the specification without having to fix anything
themselves.
Fixes: 53642399aa ("usb: gadget: f_fs: Fix wrong check on reserved1 of OS_DESC_EXT_COMPAT")
Cc: <stable@vger.kernel.org>
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Currently UDC core calls ->udc_set_speed() with the speed parameter
containing the maximum speed supported by the gadget function
driver. This might very well be more than that supported by the
UDC controller driver.
Select the lesser of the 2 speeds so both UDC and gadget function
driver are operating within limits.
This fixes PHY Erratic errors and 2 second enumeration delay on
TI's AM437x platforms.
Fixes: 6099eca796ae ("usb: gadget: core: introduce ->udc_set_speed() method")
Cc: <stable@vger.kernel.org> # v4.13+
Reported-by: Dylan Howey <Dylan.Howey@tennantco.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Considerable time ago the legacy gadget menu was added inside the
USB_ETH choice. I think this was a mistake and that the legacy
gadget menu should have been added after "endchoice" instead of
before. Hence this patch.
Fixes: commit 8443f2d2b7 ("usb: gadget: Gadget directory cleanup - group legacy gadgets")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This controller on R-Car Gen3 has 6 pipes that included PIPE 0 for
control actually. But, the datasheet has error in writing as it has
31 pipes. (However, the previous code defined 30 pipes wrongly...)
Anyway, this patch fixes it.
Fixes: 746bfe63bb ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Avoid dereferencing pointer g until after g has been sanity null checked;
move the assignment of cdev much later when it is required into a more
local scope.
Detected by CoverityScan, CID#1222135 ("Dereference before null check")
Fixes: b785ea7ce6 ("usb: gadget: composite: fix ep->maxburst initialization")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
USB vendor id and product id for Linux USB Debug Target is added.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
write_reg returns 0 on success, we can make it more explicit by returning
number 0 instead of result variable.
read_reg should return 0 on success since this is a more common pattern.
The user of read_reg has been clean-up and should be at the same commit.
Signed-off-by: Gimcuan Hui <gimcuan@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The assignment of DIV to itself is redundant and can be removed.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Remove .owner field if calls are used which set it automatically
drivers/usb/gadget/udc/bdc/bdc_core.c:645:3-8: No need to set .owner here. The core will do it.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Quectel BG96 is an Qualcomm MDM9206 based IoT modem, supporting both
CAT-M and NB-IoT. Tested hardware is BG96 mounted on Quectel
development board (EVB). The USB id is added to option.c to allow
DIAG,GPS,AT and modem communication with the BG96.
Signed-off-by: Sebastian Sjoholm <ssjoholm@mac.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This mechanically converts all remaining cases of ancient open-coded timer
setup with the old setup_timer() API, which is the first step in timer
conversions. This has no behavioral changes, since it ultimately just
changes the order of assignment to fields of struct timer_list when
finding variations of:
init_timer(&t);
f.function = timer_callback;
t.data = timer_callback_arg;
to be converted into:
setup_timer(&t, timer_callback, timer_callback_arg);
The conversion is done with the following Coccinelle script, which
is an improved version of scripts/cocci/api/setup_timer.cocci, in the
following ways:
- assignments-before-init_timer() cases
- limit the .data case removal to the specific struct timer_list instance
- handling calls by dereference (timer->field vs timer.field)
spatch --very-quiet --all-includes --include-headers \
-I ./arch/x86/include -I ./arch/x86/include/generated \
-I ./include -I ./arch/x86/include/uapi \
-I ./arch/x86/include/generated/uapi -I ./include/uapi \
-I ./include/generated/uapi --include ./include/linux/kconfig.h \
--dir . \
--cocci-file ~/src/data/setup_timer.cocci
@fix_address_of@
expression e;
@@
init_timer(
-&(e)
+&e
, ...)
// Match the common cases first to avoid Coccinelle parsing loops with
// "... when" clauses.
@match_immediate_function_data_after_init_timer@
expression e, func, da;
@@
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
(
-\(e.function\|e->function\) = func;
-\(e.data\|e->data\) = da;
|
-\(e.data\|e->data\) = da;
-\(e.function\|e->function\) = func;
)
@match_immediate_function_data_before_init_timer@
expression e, func, da;
@@
(
-\(e.function\|e->function\) = func;
-\(e.data\|e->data\) = da;
|
-\(e.data\|e->data\) = da;
-\(e.function\|e->function\) = func;
)
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
@match_function_and_data_after_init_timer@
expression e, e2, e3, e4, e5, func, da;
@@
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
... when != func = e2
when != da = e3
(
-e.function = func;
... when != da = e4
-e.data = da;
|
-e->function = func;
... when != da = e4
-e->data = da;
|
-e.data = da;
... when != func = e5
-e.function = func;
|
-e->data = da;
... when != func = e5
-e->function = func;
)
@match_function_and_data_before_init_timer@
expression e, e2, e3, e4, e5, func, da;
@@
(
-e.function = func;
... when != da = e4
-e.data = da;
|
-e->function = func;
... when != da = e4
-e->data = da;
|
-e.data = da;
... when != func = e5
-e.function = func;
|
-e->data = da;
... when != func = e5
-e->function = func;
)
... when != func = e2
when != da = e3
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
@r1 exists@
expression t;
identifier f;
position p;
@@
f(...) { ... when any
init_timer@p(\(&t\|t\))
... when any
}
@r2 exists@
expression r1.t;
identifier g != r1.f;
expression e8;
@@
g(...) { ... when any
\(t.data\|t->data\) = e8
... when any
}
// It is dangerous to use setup_timer if data field is initialized
// in another function.
@script:python depends on r2@
p << r1.p;
@@
cocci.include_match(False)
@r3@
expression r1.t, func, e7;
position r1.p;
@@
(
-init_timer@p(&t);
+setup_timer(&t, func, 0UL);
... when != func = e7
-t.function = func;
|
-t.function = func;
... when != func = e7
-init_timer@p(&t);
+setup_timer(&t, func, 0UL);
|
-init_timer@p(t);
+setup_timer(t, func, 0UL);
... when != func = e7
-t->function = func;
|
-t->function = func;
... when != func = e7
-init_timer@p(t);
+setup_timer(t, func, 0UL);
)
Signed-off-by: Kees Cook <keescook@chromium.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. Additionally corrects and on-stack
timer usage.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Duncan Sands <duncan.sands@free.fr>
Cc: "Gustavo A. R. Silva" <garsilva@embeddedor.com>
Cc: accessrunner-general@lists.sourceforge.net
Cc: linux-usb@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Allen Pais <allen.lkml@gmail.com>
There are no big surprising changes in this cycle, yet not too
boring, either. The biggest change from diffstat POV is the removal
of the legacy OSS driver codes that have been already disabled for a
long time. This will bring a few trivial merge conflicts.
As new features in ASoC side, there are two things: a new AC97 bus
implementation and AMD Stony platform support. Both include the
relevant changes shared with other subsystems, e.g. AC97 MFD changes
and DRM AMD changes.
Some other highlighted topics are:
- A bunch of USB-audio drivers got the hardening against the malicious
device accesses with a new helper code for endpoint sanity check.
- Lots of cleanups for ASoC Intel platform code, including support for
their open source audio firmware.
- Continued ASoC core componentization works.
- Support for scaling MCLK with sample rate in ASoC simple-card.
- Stabler PCM hot-unplug capability, especially for ASoC usages.
-----BEGIN PGP SIGNATURE-----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=BCBK
-----END PGP SIGNATURE-----
Merge tag 'sound-4.15-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"There are no big surprising changes in this cycle, yet not too boring,
either. The biggest change from diffstat POV is the removal of the
legacy OSS driver codes that have been already disabled for a long
time. This will bring a few trivial merge conflicts.
As new features in ASoC side, there are two things: a new AC97 bus
implementation and AMD Stony platform support. Both include the
relevant changes shared with other subsystems, e.g. AC97 MFD changes
and DRM AMD changes.
Some other highlighted topics are:
- A bunch of USB-audio drivers got the hardening against the
malicious device accesses with a new helper code for endpoint
sanity check
- Lots of cleanups for ASoC Intel platform code, including support
for their open source audio firmware
- Continued ASoC core componentization works
- Support for scaling MCLK with sample rate in ASoC simple-card
- Stabler PCM hot-unplug capability, especially for ASoC usages"
* tag 'sound-4.15-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (302 commits)
Documentation: sound: hd-audio: notes.rst
ASoC: bcm2835: Support left/right justified and DSP modes
ASoC: bcm2835: Enforce full symmetry
ASoC: bcm2835: Support additional samplerates up to 384kHz
ASoC: bcm2835: Add support for TDM modes
ASoC: add mclk-fs support to audio graph card
ASoC: add mclk-fs to audio graph card binding
ASoC: rt5514: work around link error
ASoC: rt5514: mark PM functions as __maybe_unused
ASoC: rt5663: Check the JD status in the button pushing
ASoC: amd: Modified DMA transfer Mechanism for Playback
ASoC: rt5645: Wait for 400msec before concluding on value of RT5645_VENDOR_ID2
ASoC: sun4i-codec: fixed 32bit audio capture support for H3/H2+
ASoC: da7213: add support for DSP modes
ASoC: sun8i-codec: Add a comment on the LRCK inversion
ASoC: sun8i-codec: Set the BCLK divider
ASoC: rt5663: Delay and retry reading rt5663 ID register
ASoC: amd: use do_div rather than 64 bit division to fix 32 bit builds
ASoC: cs42l56: Fix reset GPIO name in example DT binding
ASoC: rt5514-spi: check irq status to schedule data copy in resume function
...
- proper use of the bool type (Thomas Meyer)
- constification of struct config_item_type (Bhumika Goyal)
-----BEGIN PGP SIGNATURE-----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=+tMO
-----END PGP SIGNATURE-----
Merge tag 'configfs-for-4.15' of git://git.infradead.org/users/hch/configfs
Pull configfs updates from Christoph Hellwig:
"A couple of configfs cleanups:
- proper use of the bool type (Thomas Meyer)
- constification of struct config_item_type (Bhumika Goyal)"
* tag 'configfs-for-4.15' of git://git.infradead.org/users/hch/configfs:
RDMA/cma: make config_item_type const
stm class: make config_item_type const
ACPI: configfs: make config_item_type const
nvmet: make config_item_type const
usb: gadget: configfs: make config_item_type const
PCI: endpoint: make config_item_type const
iio: make function argument and some structures const
usb: gadget: make config_item_type structures const
dlm: make config_item_type const
netconsole: make config_item_type const
nullb: make config_item_type const
ocfs2/cluster: make config_item_type const
target: make config_item_type const
configfs: make ci_type field, some pointers and function arguments const
configfs: make config_item_type const
configfs: Fix bool initialization/comparison
Here is the big set of USB and PHY driver updates for 4.15-rc1.
There is the usual amount of gadget and xhci driver updates, along with
phy and chipidea enhancements. There's also a lot of SPDX tags and
license boilerplate cleanups as well, which provide some churn in the
diffstat.
Other major thing is the typec code that moved out of staging and into
the "real" part of the drivers/usb/ tree, which was nice to see happen.
All of these have been in linux-next with no reported issues for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgm/Vw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yktXwCdGgpInfOEvOGFd83EPDL7a1ncyc4AoM5wI8yl
1CeLipqVIN3IsMMJptvb
=zvDI
-----END PGP SIGNATURE-----
Merge tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big set of USB and PHY driver updates for 4.15-rc1.
There is the usual amount of gadget and xhci driver updates, along
with phy and chipidea enhancements. There's also a lot of SPDX tags
and license boilerplate cleanups as well, which provide some churn in
the diffstat.
Other major thing is the typec code that moved out of staging and into
the "real" part of the drivers/usb/ tree, which was nice to see
happen.
All of these have been in linux-next with no reported issues for a
while"
* tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
usb: gadget: f_fs: Fix use-after-free in ffs_free_inst
USB: usbfs: compute urb->actual_length for isochronous
usb: core: message: remember to reset 'ret' to 0 when necessary
USB: typec: Remove remaining redundant license text
USB: typec: add SPDX identifiers to some files
USB: renesas_usbhs: rcar?.h: add SPDX tags
USB: chipidea: ci_hdrc_tegra.c: add SPDX line
USB: host: xhci-debugfs: add SPDX lines
USB: add SPDX identifiers to all remaining Makefiles
usb: host: isp1362-hcd: remove a couple of redundant assignments
USB: adutux: remove redundant variable minor
usb: core: add a new usb_get_ptm_status() helper
usb: core: add a 'type' parameter to usb_get_status()
usb: core: introduce a new usb_get_std_status() helper
usb: core: rename usb_get_status() 'type' argument to 'recip'
usb: core: add Status Type definitions
USB: gadget: Remove redundant license text
USB: gadget: function: Remove redundant license text
USB: gadget: udc: Remove redundant license text
USB: gadget: legacy: Remove redundant license text
...
Here is the "big" staging and IIO driver update for 4.15-rc1.
Lots and lots of little changes, almost all minor code cleanups as the
Outreachy application process happened during this development cycle.
Also happened was a lot of IIO driver activity, and the typec USB code
moving out of staging to drivers/usb (same commits are in the USB tree
on a persistent branch to not cause merge issues.)
Overall, it's a wash, I think we added a few hundred more lines than
removed, but really only a few thousand were modified at all.
All of these have been in linux-next for a while. There might be a
merge issue with Al's vfs tree in the pi433 driver (take his changes,
they are always better), and the media tree with some of the odd atomisp
cleanups (take the media tree's version).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgnFrg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymxbwCgtNlBkqD2JJYpLRKvI/C4w1vzZsEAnA2THRkt
g3ioPBqmqC/2DSbldr2o
=/ebw
-----END PGP SIGNATURE-----
Merge tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO updates from Greg KH:
"Here is the "big" staging and IIO driver update for 4.15-rc1.
Lots and lots of little changes, almost all minor code cleanups as the
Outreachy application process happened during this development cycle.
Also happened was a lot of IIO driver activity, and the typec USB code
moving out of staging to drivers/usb (same commits are in the USB tree
on a persistent branch to not cause merge issues.)
Overall, it's a wash, I think we added a few hundred more lines than
removed, but really only a few thousand were modified at all.
All of these have been in linux-next for a while. There might be a
merge issue with Al's vfs tree in the pi433 driver (take his changes,
they are always better), and the media tree with some of the odd
atomisp cleanups (take the media tree's version)"
* tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (507 commits)
staging: lustre: add SPDX identifiers to all lustre files
staging: greybus: Remove redundant license text
staging: greybus: add SPDX identifiers to all greybus driver files
staging: ccree: simplify ioread/iowrite
staging: ccree: simplify registers access
staging: ccree: simplify error handling logic
staging: ccree: remove dead code
staging: ccree: handle limiting of DMA masks
staging: ccree: copy IV to DMAable memory
staging: fbtft: remove redundant initialization of buf
staging: sm750fb: Fix parameter mistake in poke32
staging: wilc1000: Fix bssid buffer offset in Txq
staging: fbtft: fb_ssd1331: fix mirrored display
staging: android: Fix checkpatch.pl error
staging: greybus: loopback: convert loopback to use generic async operations
staging: greybus: operation: add private data with get/set accessors
staging: greybus: loopback: Fix iteration count on async path
staging: greybus: loopback: Hold per-connection mutex across operations
staging: greybus/loopback: use ktime_get() for time intervals
staging: fsl-dpaa2/eth: Extra headroom in RX buffers
...
Pull timer updates from Thomas Gleixner:
"Yet another big pile of changes:
- More year 2038 work from Arnd slowly reaching the point where we
need to think about the syscalls themself.
- A new timer function which allows to conditionally (re)arm a timer
only when it's either not running or the new expiry time is sooner
than the armed expiry time. This allows to use a single timer for
multiple timeout requirements w/o caring about the first expiry
time at the call site.
- A new NMI safe accessor to clock real time for the printk timestamp
work. Can be used by tracing, perf as well if required.
- A large number of timer setup conversions from Kees which got
collected here because either maintainers requested so or they
simply got ignored. As Kees pointed out already there are a few
trivial merge conflicts and some redundant commits which was
unavoidable due to the size of this conversion effort.
- Avoid a redundant iteration in the timer wheel softirq processing.
- Provide a mechanism to treat RTC implementations depending on their
hardware properties, i.e. don't inflict the write at the 0.5
seconds boundary which originates from the PC CMOS RTC to all RTCs.
No functional change as drivers need to be updated separately.
- The usual small updates to core code clocksource drivers. Nothing
really exciting"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (111 commits)
timers: Add a function to start/reduce a timer
pstore: Use ktime_get_real_fast_ns() instead of __getnstimeofday()
timer: Prepare to change all DEFINE_TIMER() callbacks
netfilter: ipvs: Convert timers to use timer_setup()
scsi: qla2xxx: Convert timers to use timer_setup()
block/aoe: discover_timer: Convert timers to use timer_setup()
ide: Convert timers to use timer_setup()
drbd: Convert timers to use timer_setup()
mailbox: Convert timers to use timer_setup()
crypto: Convert timers to use timer_setup()
drivers/pcmcia: omap1: Fix error in automated timer conversion
ARM: footbridge: Fix typo in timer conversion
drivers/sgi-xp: Convert timers to use timer_setup()
drivers/pcmcia: Convert timers to use timer_setup()
drivers/memstick: Convert timers to use timer_setup()
drivers/macintosh: Convert timers to use timer_setup()
hwrng/xgene-rng: Convert timers to use timer_setup()
auxdisplay: Convert timers to use timer_setup()
sparc/led: Convert timers to use timer_setup()
mips: ip22/32: Convert timers to use timer_setup()
...
The biggest thing this release has been the conversion of the AC98 bus
to the driver model, that's been a long time coming so thanks to Robert
Jarzmik for his dedication there. Due to there being some AC97 MFD
there's a few fairly large changes in input and the MFD layer, mainly to
the wm97xx driver.
There's also some drivers/drm changes to support the new AMD Stoney
platform, these are shared with the DRM subsystem and should be being
merged via both.
Within the subsystem the overwhelming bulk of the changes is in the
Intel drivers which continue to need lots of cleanups and fixes, this
release they've also gained support for their open source firmware.
There's also some large changs in the core as Morimoto-san continues to
mirror operations into the component level in preparation for conversion
of drivers to that.
- The AC97 bus has finally caught up with the driver model thanks to
some dedicated and persistent work from Robert Jarzmik.
- Continued work from Morimoto-san on moving us towards being able to
use components for everything.
- Lots of cleanups for the Intel platform code, including support for
their open source audio firmware.
- Support for scaling MCLK with sample rate in simple-card.
- Support for AMD Stoney platform.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAloJhwMTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0KzbB/9tXryXYz3dnKVlm9rk+Cq0Xy4TrUNk
WY+Il+Di1b6CQJbAm9GSacJxR+siupZCjGC5roHznj/AA2l0RuxJXpxG40Db8ZX+
bDR7mIWtuTUJHazqXltafj9ydElRKVpOGPAi5YJhhW5bXQ3SR9fFy0D3mdcT02v4
SyMExhOMz+mdnuBhbWx9kqJ9LPzCs0ow+R4uoRgAQxpFXPBGtq06sMkK86lGfsl/
iRM36J6FIeIQQfSHG/dkkpoybVax43z4OH7G1IL2FOU7miwkjZh/TTh/xHTd86Mc
OOuGu4hB+MjvccSOa9HSrOqFjxtkZipstwqYVWoYQcUoIVpcg0YRk7TG
=5KBY
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v4.15
The biggest thing this release has been the conversion of the AC98 bus
to the driver model, that's been a long time coming so thanks to Robert
Jarzmik for his dedication there. Due to there being some AC97 MFD
there's a few fairly large changes in input and the MFD layer, mainly to
the wm97xx driver.
There's also some drivers/drm changes to support the new AMD Stoney
platform, these are shared with the DRM subsystem and should be being
merged via both.
Within the subsystem the overwhelming bulk of the changes is in the
Intel drivers which continue to need lots of cleanups and fixes, this
release they've also gained support for their open source firmware.
There's also some large changs in the core as Morimoto-san continues to
mirror operations into the component level in preparation for conversion
of drivers to that.
- The AC97 bus has finally caught up with the driver model thanks to
some dedicated and persistent work from Robert Jarzmik.
- Continued work from Morimoto-san on moving us towards being able to
use components for everything.
- Lots of cleanups for the Intel platform code, including support for
their open source audio firmware.
- Support for scaling MCLK with sample rate in simple-card.
- Support for AMD Stoney platform.
KASAN enabled configuration reports an error
BUG: KASAN: use-after-free in ffs_free_inst+... [usb_f_fs] at addr ...
Write of size 8 by task ...
This is observed after "ffs-test" is run and interrupted. If after that
functionfs is unmounted and g_ffs module is unloaded, that use-after-free
occurs during g_ffs module removal.
Although the report indicates ffs_free_inst() function, the actual
use-after-free condition occurs in _ffs_free_dev() function, which
is probably inlined into ffs_free_inst().
This happens due to keeping the ffs_data reference in device structure
during functionfs unmounting, while ffs_data itself is freed as no longer
needed. The fix is to clear that reference in ffs_closed() function,
which is a counterpart of ffs_ready(), where the reference is stored.
Fixes: 3262ad8243 ("usb: gadget: f_fs: Stop ffs_closed NULL pointer dereference")
Cc: stable@vger.kernel.org
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB kerneldoc says that the actual_length field "is read in
non-iso completion functions", but the usbfs driver uses it for all
URB types in processcompl(). Since not all of the host controller
drivers set actual_length for isochronous URBs, programs using usbfs
with some host controllers don't work properly. For example, Minas
reports that a USB camera controlled by libusb doesn't work properly
with a dwc2 controller.
It doesn't seem worthwhile to change the HCDs and the documentation,
since the in-kernel USB class drivers evidently don't rely on
actual_length for isochronous transfers. The easiest solution is for
usbfs to calculate the actual_length value for itself, by adding up
the lengths of the individual packets in an isochronous transfer.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Reported-and-tested-by: wlf <wulf@rock-chips.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_control_msg() will return the amount of bytes transferred, if that
amount matches what we wanted to transfer, we need to reset 'ret' to 0
from usb_get_status().
Fixes: 2e43f0fe37 ("usb: core: add a 'type' parameter to usb_get_status()")
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Yueyao Zhu <yueyao.zhu@gmail.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to these typec files being moved into the drivers/usb/ directory in
this tree, they missed the larger "add SPDX tags to all files" work. So
add the correct SPDX license tag, based on the license text in the file
itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Yueyao Zhu <yueyao.zhu@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These files somehow never got an SPDX tag added to them, maybe due to
the small size. So provide the default identifier of the whole project:
SPDX-License-Identifier: GPL-2.0
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
Cc: Rob Herring <robh@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The license text was removed from this file, yet they somehow missed
the big "add SPDX tags to all files" sweep due to them being new. So
add the proper SPDX license tag to them, based on the original license
text in the file.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The license text was removed from these files, yet they somehow missed
the big "add SPDX tags to all files" sweep due to them being new. So
add the proper SPDX license tag to them, based on the original license
text in the file.
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
This updates the remaining drivers/usb/*Makefile* that were missing SPDX
identifiers. They all get the following identifier:
SPDX-License-Identifier: GPL-2.0
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: Johan Hovold <johan@kernel.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable index is being initialized and the value is never read,
it is being updated a few statements later, so remove the redundant
initialization. Variable total is being updated but the value is
never read, so this is also redundant and can be removed. Cleans
up two clang warnings:
drivers/usb/host/isp1362-hcd.c:715:6: warning: Value stored to
'index' during its initialization is never read
drivers/usb/host/isp1362-hcd.c:2254:2: warning: Value stored to
'total' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable minor is being assigned but never read, hence it is redundant
and can be removed. Cleans up clang warning:
drivers/usb/misc/adutux.c:770:2: warning: Value stored to 'minor' is
never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This new 'type' parameter will allows interested drivers to request
for PTM status or Standard status.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This new helper is a simple wrapper around usb_get_status(). This
patch is in preparation to adding support for fetching PTM_STATUS
types. No functional changes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This makes it a lot clearer that we're expecting a recipient as the
argument. A follow-up patch will use the argument 'type' as the status
type selector (standard or ptm).
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB 3.1 added a PTM_STATUS type. Let's add a define for it and
following patches will let usb_get_status() accept the new argument.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Jerry Zhang <zhangjerry@google.com>
Cc: John Keeping <john@metanate.com>
Cc: Krzysztof Opasiak <k.opasiak@samsung.com>
Cc: Abdulhadi Mohamed <abdulahhadi2@gmail.com>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Cc: Raviteja Garimella <raviteja.garimella@broadcom.com>
Cc: Romain Perier <romain.perier@collabora.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Al Cooper <alcooperx@gmail.com>
Cc: Srinath Mannam <srinath.mannam@broadcom.com>
Cc: Roger Quadros <rogerq@ti.com>
Cc: Krzysztof Opasiak <k.opasiak@samsung.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: "Felix Hädicke" <felixhaedicke@web.de>
Cc: Peter Chen <peter.chen@nxp.com>
Cc: Allen Pais <allen.lkml@gmail.com>
Cc: Yuyang Du <yuyang.du@intel.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Johan Hovold <johan@kernel.org>
Cc: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Cc: Peter Chen <peter.chen@nxp.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Windsor <dwindsor@gmail.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Johan Hovold <johan@kernel.org>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: John Youn <johnyoun@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Acked-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Johan Hovold <johan@kernel.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Rob Herring <robh@kernel.org>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Cc: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We already have renesas_usbhs_get_info() macro.
Let's use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This gets rid of the deprecated do_gettimeofday() function in usbip.
The comment above vgadget_get_frame() mentions that it suffers
from issues with the time jumps due to suspend and settimeofday,
so I'm changing it to use ktime_get_ts64() to use monotonic times
that don't have this problem.
I couldn't tell whether we should use CLOCK_MONOTONIC or
CLOCK_MONOTONIC_RAW here, the difference being the exact rate
when correcting for NTP. I picked monotonic time since it doesn't
change the speed to the existing code and should be better
synchronized with other machines we talk to.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vgadget_get_frame returns a frame number from 0 to 2046, which
may require an expensive division operation to wrap at one lower
than the usual number.
I can't see any reason for this, and all other drivers wrap at
a power-of-two number. My best explanation is that it was a simple
typo, so I'm changing the % modulo operator into a cheaper bitmask
that the other drivers use, to make it wrap after 0x7ff rather than
before it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The product ID for "Linux USB GDB Target device" has been
changed. Change the driver binding table accordingly.
This patch should be back-ported to kernels as old as v4.12,
that contain the commit 57fb47279a ("usb/serial: Add DBC
debug device support to usb_debug").
Cc: <stable@vger.kernel.org> # v4.12+
Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DbC register set defines an interface for system software
to specify the vendor id and product id for the debug device.
These two values will be presented by the debug device in its
device descriptor idVendor and idProduct fields.
The current used product ID is a place holder. We now have a
valid one. The description strings are changed accordingly.
This patch should be back-ported to kernels as old as v4.12,
that contain the commit aeb9dd1de9 ("usb/early: Add driver
for xhci debug capability").
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without this patch, K70 LUX keyboards don't work, saying
usb 3-3: unable to read config index 0 descriptor/all
usb 3-3: can't read configurations, error -110
usb usb3-port3: unable to enumerate USB device
Signed-off-by: Bernhard Rosenkraenzer <Bernhard.Rosenkranzer@linaro.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several GPL-2.0 drivers used "GPL" rather than "GPL v2" in their
MODULE_LICENSE macros; fix the macros to match the licenses.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Peter Chen <Peter.Chen@nxp.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Duncan Sands <duncan.sands@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Keith Packard <keithp@keithp.com>
Cc: Juergen Stuber <starblue@users.sourceforge.net>
Cc: Cesar Miquel <miquel@df.uba.ar>
Cc: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't populate the const array max_packet_array on the stack, instead make
it static. Makes the object code smaller by over 90 bytes:
Before:
text data bss dec hex filename
34337 5612 128 40077 9c8d renesas_usb3.o
After:
text data bss dec hex filename
34149 5708 128 39985 9c31 renesas_usb3.o
(gcc version 7.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To match the rest of the kernel, the SPDX tags for the drivers/usb/core/
files are moved to the first line of the file. This makes it more
obvious the tag is present as well as making it match the other 12k
files in the tree with this location.
It also uses // to match the "expected style" as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The support for 36-bit addresses originally came with an incorrect
printk format for dma addresses. Felipe changed the format string it
while applying, but the result was still incorrect, since we now have
to pass a pointer to the address instead of the integer value:
drivers/usb/mtu3/mtu3_qmu.c: In function 'mtu3_prepare_tx_gpd':
drivers/usb/mtu3/mtu3_qmu.c:261:25: error: format '%p' expects argument of type 'void *', but argument 7 has type 'dma_addr_t {aka unsigned int}' [-Werror=format=]
drivers/usb/mtu3/mtu3_qmu.c: In function 'mtu3_prepare_rx_gpd':
drivers/usb/mtu3/mtu3_qmu.c:300:25: error: format '%p' expects argument of type 'void *', but argument 7 has type 'dma_addr_t {aka unsigned int}' [-Werror=format=]
This fixes the printk argument accordingly.
Fixes: 1a46dfea08 ("usb: mtu3: support 36-bit DMA address")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The time_t type and time_to_tm() function are deprecated because
of y2038 problems. In this driver, they are used to pretty-print
the timestamp of the firmware build. This is fine as long as
we don't get a firmware build past 2038.
Converting to time64_t and time64_to_tm() avoids the deprecated
interfaces and works until 2106, when the firmware-defined
data structure overflows.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the USB-serial updates for 4.15-rc1, including:
- three fixes for longstanding issues in garmin_gps and metro-usb which
could lead to NULL-pointer dereferences and memory leaks
- a workaround for broken f81534 firmware-handling of overruns
- f81534 break support, and
- conversion to timer_setup()
Included are also various clean ups and a new qcserial device id.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=GqYH
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.15-rc1
Here are the USB-serial updates for 4.15-rc1, including:
- three fixes for longstanding issues in garmin_gps and metro-usb which
could lead to NULL-pointer dereferences and memory leaks
- a workaround for broken f81534 firmware-handling of overruns
- f81534 break support, and
- conversion to timer_setup()
Included are also various clean ups and a new qcserial device id.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. Also adds missing call to
destroy_timer_on_stack();
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: "Gustavo A. R. Silva" <garsilva@embeddedor.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing break statement to prevent the code for case C_HUB_OVER_CURRENT
from falling through to case C_HUB_LOCAL_POWER.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Generic drivers like this need to control arbitrary number of reset
lines. Instead of hard-coding the maximum number of resets, use the
reset array API. It can manage a bunch of resets behind the scene.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Generic drivers like this need to control arbitrary number of reset
lines. Instead of hard-coding the maximum number of resets, use the
reset array API. It can manage a bunch of resets behind the scene.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the intended use of this option easier to grasp.
Signed-off-by: Chris Mayo <aklhfex@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver used to be developed with legacy GPIO API support. It's
better to use descriptor-based interface for several reasons. First
of all the legacy API doesn't support the ACTIVE_LOW/HIGH flag of dts
nodes, which is essential since different hardware may have different
GPIOs connectivity including the logical value inversion. Secondly,
by requesting the reset GPIO descriptor the driver prevent the other
applications from changing its value. And last but not least the
legacy GPIO interface should be avoided in the new code due to it
obsolescence.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This parameters may be varied in accordance with hardware specifics.
So lets add the corresponding settings to the usb251xb driver dts
specification.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The methods like of_property_read_u32 utilizing the specified
pointer permit only the pointer to a preallocated u32 storage as the
third argument. As a result the driver crashes on NULL pointer
dereference in case if "oc-delay-us" or "power-on-time-ms" declared
in dts file.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB2517 supports two LED modes: USB mode and speed (default) indication
mode. The last one can be switched on by corresponding dts property.
Since USB251xb hubs doesn't support LEDs settings, we need to ignore
this setting.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Battery charging settings are supported by USB251xb hubs only.
USB2517i isn't one of them. So we need to reflect it within the
device-specific data structure. The driver doesn't support dts
property changing this setting, but instead defaults it with zero.
So the flag isn't used anywhere in the driver, but still can be helpful
in future, when necessity of the corresponding dts setting arises.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB electrical signaling drive strength boost bit is also supported
by USB2517 hub. Since it got three addition ports, the designers
needed to add one more register for initialization. It turned out
to be formerly reserved 0xF7. As before we just initialize it with
default zeros.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB2517 got three additionl downstream ports, which can
as well be mapped to another logical ports. USB251xb driver
currently doesn't fully support such setting configuration
from dts file. This patch doesn't change this, but adds
usb2517 spcific ports default liner mapping.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB251xb as well as USB2517 datasheet states, that all these
hubs differ by number of ports declared as the last digit in the
model name. So USB2512 got two ports, USB2513 - three, and so on.
Such setting must be reflected in the device specific data
structure and corresponding dts property should be checked whether
it doesn't get out of available ports.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are USB2517 and USB2517i hubs, which have almost the same
registers space as already supported USB251xBi series. The difference
it in DIDs and in a few functions. This patch adds the USB2517/i data
structures to the driver, so it would have different setting depending
on the device discovered on i2c-bus.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We do not have to test if platform_data pointer is null in
max3421_hub_control(), as the driver probe will fail if no
platform_data is found.
Fixes: 721fdc83b3 ("usb: max3421: Add devicetree support")
Signed-off-by: Jules Maselbas <jules.maselbas@grenoble-inp.org>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No Qualcomm SoC requires the "phy-qcom-8x16-usb.c" USB phy driver
support any more, so remove the code.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No Qualcomm SoC requires the "phy-msm-usb.c" USB phy driver support
any more, so remove the code.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No Qualcomm SoC requires the "ehci-msm.c" code any more. So remove it.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pointer urbp is assigned but is never read, hence it is redundant
and can be removed. Cleans up clang warning:
drivers/usb/c67x00/c67x00-sched.c:975:2: warning: Value stored to 'urbp'
is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1162594
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 115016
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 115006
Addresses-Coverity-ID: 115007
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. Adds a static tracking variable to
match the timer global.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. This rearranges the arrays of timers
to minimize the need for a pointer back to the main structure.
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: "Gustavo A. R. Silva" <garsilva@embeddedor.com>
Cc: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8b52291a07 ("usb-storage: fix deadlock involving host lock
and scsi_done") added a local variable to usb_stor_control_thread() in
the usb-storage driver. This local variable holds the value of
us->srb, for use after the host lock has been released.
But as long as we have the value in a local variable, we may as well
use it instead of dereferencing the us pointer all over the place.
This patch makes no functional change; it just makes the code a little
shorter and a little neater.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 115004
Addresses-Coverity-ID: 115005
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use put_unaligned_le32 rather than using byte ordering function and
memcpy which makes code clear.
Also, add the header file where it is declared.
Done using Coccinelle and semantic patch used is :
@ rule1 @
identifier tmp; expression ptr,x; type T;
@@
- tmp = cpu_to_le32(x);
<+... when != tmp
- memcpy(ptr, (T)&tmp, ...);
+ put_unaligned_le32(x,ptr);
...+>
@ depends on rule1 @
type j; identifier tmp;
@@
- j tmp;
...when != tmp
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now struct musb has the timer (dev_timer) for glue drivers, so let's
remove the duplicated timer defined in dsps glue driver, and use
dev_timer defined in struct musb.
Signed-off-by: Bin Liu <b-liu@ti.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Instead of a per-device static timer variable, a spare timer "dev_timer"
is added to the musb structure for devices to use for their per-device
timer.
Cc: linux-usb@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement Fintek f81534 break on/off with LCR register.
It's the same with 16550A LCR register layout.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The F81532/534 without this patch will hang-up on data overrun.
It's caused by enable LSR interrupt in IER by default and occur data
overrun, the chip will busy for process LSR interrupt but not read LSR
internally. It will not responed for USB control endpoint0 and we can't
read LSR from driver in this situration.
So we'll disable the LSR interrupt in probe() and submit the LSR worker to
clear LSR state when reported LSR error bit with bulk-in data in
f81534_process_per_serial_block().
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add USB PID/VID for Sierra Wireless EM7355 LTE modem QDL firmware update
mode.
Signed-off-by: Douglas Fischer <douglas.fischer@outlook.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 115014
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1397608
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is some registers defined in da8xx.c though they are not used.
These registers are also defined and used in musb_cppi41.c
Remove these defines from da8xx.c.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vbus is there using new USB charger API.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZ9ojfAAoJEEhZKYFQ1nG70g4IAJNeDnpWkzNVsM5Y8yQyWZSm
sAULcX1hRSu71RzCRsXEnJ4Ur5XGrHdA67wJFyJV5JMlh2l1b+3pZfd22zv5XQJS
3KPUQ4D89ZMEVzoaH6/mNM7TbIlGBS5f8g1HO+duevkVxoL2Fk1/4N04VousPhj9
HZgdZzUft+5HMsosqMCH2s2KixwzNsmtq3pz5sadXI0yt3j4pqQwboKfOjUX+BRP
Wh/ATvL+MpyqBn9TYGXRVXY4JKtA7h626OUPjqj6eM0lreXIcANA1eraOed79zR1
hyTvz+GG7c+bHWOBnntuGsZp0UHUeAqpLEsV321PIqhpkqkFcGPl3a+t9mgLaJ4=
=efLD
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
The main change for this rc is notify USB charger present when
vbus is there using new USB charger API.
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Detailed description for this pull request:
1. Split out extcon header file for consumer and provider device
: The extcon has two type of extcon devices as following.
- 'extcon provider deivce' adds new extcon device and detect
the state/properties of external connector. Also, it notifies the
state/properties to the extcon consumer device.
- 'extcon consumer device' gets the change state/properties
from extcon provider device.
Prior to that, include/linux/extcon.h contains all exported API
for both provider and consumer device driver. To clarify the meaning
of header file and to remove the wrong use-case on consumer device.
- include/linux/extcon-provider.h includes API for the provider device driver.
- include/linux/extcon.h includes the API for the consumer device driver.
2. Support the SmartDock accessory on extcon-max77843.c device driver
- Support the SmartDock accessory which detects following connectors
at the same time.
: USB host throught USB hub for mouse, keyboard and so on.
: MHL connector for video output.
: Charger connector for battery charging.
- It tested with Unitek Y-2165 MHL+OTG Hub Smart Phone Dock.
3. Fix the minor issue of extcon driver
- Delete the unneeded initialization in extcon-max14577.
- Make extcon_info static const in order to fix the warning.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gWvl
-----END PGP SIGNATURE-----
Merge tag 'extcon-next-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into usb-next
Chanwoo writes:
Update extcon for 4.15
Detailed description for this pull request:
1. Split out extcon header file for consumer and provider device
: The extcon has two type of extcon devices as following.
- 'extcon provider deivce' adds new extcon device and detect
the state/properties of external connector. Also, it notifies the
state/properties to the extcon consumer device.
- 'extcon consumer device' gets the change state/properties
from extcon provider device.
Prior to that, include/linux/extcon.h contains all exported API
for both provider and consumer device driver. To clarify the meaning
of header file and to remove the wrong use-case on consumer device.
- include/linux/extcon-provider.h includes API for the provider device driver.
- include/linux/extcon.h includes the API for the consumer device driver.
2. Support the SmartDock accessory on extcon-max77843.c device driver
- Support the SmartDock accessory which detects following connectors
at the same time.
: USB host throught USB hub for mouse, keyboard and so on.
: MHL connector for video output.
: Charger connector for battery charging.
- It tested with Unitek Y-2165 MHL+OTG Hub Smart Phone Dock.
3. Fix the minor issue of extcon driver
- Delete the unneeded initialization in extcon-max14577.
- Make extcon_info static const in order to fix the warning.
This patch fixes a trivial typo to get the module name ci_hdrc.ko correct.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
drivers/usb/host/xhci-mtk.c:256:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: scripts/coccinelle/api/ptr_ret.cocci
Fixes: b6bb72cf0d ("usb: xhci-mtk: add optional mcu and dma bus clocks")
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Not much going on this time around. With only 51 non-merge commits,
this was one of the smallest pull requests from the Gadget tree.
Most of the changes are in the mtu3 driver which added support for
36-bit DMA, support for USB 3.1 and support for dual-role (along with
some non-critical fixes).
The dwc2 driver got a few improvements to how we handle gadget state
tracking and also added support for STM32F7xx devices.
Other than that, we just some minor non-critical fixes and
improvements all over the place.
-----BEGIN PGP SIGNATURE-----
iQJRBAABCgA7FiEElLzh7wn96CXwjh2IzL64meEamQYFAlnvDUQdHGZlbGlwZS5i
YWxiaUBsaW51eC5pbnRlbC5jb20ACgkQzL64meEamQbaFg//WorvPDm7vu/o5G4r
pMCLodF0Ye6sFs5Ug2X2Fr3sXpRTlr6LfPi6Zt3rwimF5EBtDuNF0Tu8jKj0vfSI
iKYpXIvDOc4DVeqMiQzw3kBt8FQcUjb8cVV2VUbO9ata0ALUF3TH27PUIS0R1vTG
HOhSx4EVIkpp2vM9XOFBWi2e46HsDscoymGNXn/b3WmAUysPoNf+7i9NUgI88VHZ
KbFmdYlMyvPTOQsJM3EaNIoGmWzoNtuBU+W0aO0h17QweGaDDpINBFocCru/MWT3
d8IaRtkHmq+nUYMM3IrKCL0i40uq86ckm110jEYhBLkZsAlf728118MKnD4PnJoR
NMnRn1xLV0/JbGV0Nq1Kz0WefYiWj7nsve7TNnDDteJ8PKZTzQUSb0LQ4KIQTBo3
3LfeQgRmhzSafJ11xr1IWiVti7D6ijkqMw8R+z+YazTCN9Mgwt0aA/BFDihcSNR8
Qan9VHqiCvldfJCY0a+VoD5lE1zWeYqBkDF2XhrjuhEvfo9fjrJnJ1ElQhFDT8w8
zJDerBpxuVlYZta45t7PKS6Y4XiuVZrwXo8ilTQEVg68KoJ4GX7GhKJbfResuaKB
OvSvr2aRCAAKhXil7C8sRVjdpRdLhKNY6NQisxEwhrqaGI7RzWIhibFlHGWwLNNv
HYjtoNi5JcZmeteEdXeBLRyPUtI=
=nkak
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v4.15 merge window
Not much going on this time around. With only 51 non-merge commits,
this was one of the smallest pull requests from the Gadget tree.
Most of the changes are in the mtu3 driver which added support for
36-bit DMA, support for USB 3.1 and support for dual-role (along with
some non-critical fixes).
The dwc2 driver got a few improvements to how we handle gadget state
tracking and also added support for STM32F7xx devices.
Other than that, we just some minor non-critical fixes and
improvements all over the place.
It has been noticed that the dwc2 udc state reporting doesn't
seem to work (at least on HiKey boards). Where after the initial
setup, the sysfs /sys/class/udc/f72c0000.usb/state file would
report "configured" no matter the state of the OTG port.
This patch adds a call so that we report to the UDC layer when
the gadget device is disconnected.
This patch does depend on the previous patch ("usb: dwc2:
Improve gadget state disconnection handling") in this patch set
in order to properly work.
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: YongQin Liu <yongqin.liu@linaro.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Tested-by: Minas Harutyunyan <hminas@synopsys.com>
Reported-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We've found that while in host mode, using Android, if one runs
the command:
stop adbd
The existing usb devices being utilized in host mode are disconnected.
This is most visible with usb networking devices.
This seems to be due to adbd closing the file:
/dev/usb-ffs/adb/ep0
Which calls ffs_ep0_release() and the following backtrace:
[<ffffff800875a430>] dwc2_hsotg_ep_disable+0x148/0x150
[<ffffff800875a498>] dwc2_hsotg_udc_stop+0x60/0x110
[<ffffff8008787950>] usb_gadget_remove_driver+0x58/0x78
[<ffffff80087879e4>] usb_gadget_unregister_driver+0x74/0xe8
[<ffffff80087850c0>] unregister_gadget+0x28/0x58
[<ffffff800878511c>] unregister_gadget_item+0x2c/0x40
[<ffffff8008790ea8>] ffs_data_clear+0xe8/0xf8
[<ffffff8008790ed8>] ffs_data_reset+0x20/0x58
[<ffffff8008793218>] ffs_data_closed+0x98/0xe8
[<ffffff80087932d8>] ffs_ep0_release+0x20/0x30
Then when dwc2_hsotg_ep_disable() is called, we call
kill_all_requests() which causes a bunch of the following
messages:
dwc2 f72c0000.usb: Mode Mismatch Interrupt: currently in Host mode
dwc2 f72c0000.usb: Mode Mismatch Interrupt: currently in Host mode
dwc2 f72c0000.usb: Mode Mismatch Interrupt: currently in Host mode
dwc2 f72c0000.usb: Mode Mismatch Interrupt: currently in Host mode
dwc2 f72c0000.usb: Mode Mismatch Interrupt: currently in Host mode
dwc2 f72c0000.usb: Mode Mismatch Interrupt: currently in Host mode
dwc2 f72c0000.usb: Mode Mismatch Interrupt: currently in Host mode
dwc2 f72c0000.usb: Mode Mismatch Interrupt: currently in Host mode
init: Service 'adbd' (pid 1915) killed by signal 9
init: Sending signal 9 to service 'adbd' (pid 1915) process group...
init: Successfully killed process cgroup uid 0 pid 1915 in 0ms
init: processing action (init.svc.adbd=stopped) from (/init.usb.configfs.rc:15)
dwc2 f72c0000.usb: dwc2_hc_chhltd_intr_dma: Channel 8 - ChHltd set, but reason is unknown
dwc2 f72c0000.usb: hcint 0x00000002, intsts 0x04200029
dwc2 f72c0000.usb: dwc2_hc_chhltd_intr_dma: Channel 12 - ChHltd set, but reason is unknown
dwc2 f72c0000.usb: hcint 0x00000002, intsts 0x04200029
dwc2 f72c0000.usb: dwc2_hc_chhltd_intr_dma: Channel 15 - ChHltd set, but reason is unknown
dwc2 f72c0000.usb: hcint 0x00000002, intsts 0x04200029
dwc2 f72c0000.usb: dwc2_hc_chhltd_intr_dma: Channel 3 - ChHltd set, but reason is unknown
dwc2 f72c0000.usb: hcint 0x00000002, intsts 0x04200029
dwc2 f72c0000.usb: dwc2_hc_chhltd_intr_dma: Channel 4 - ChHltd set, but reason is unknown
dwc2 f72c0000.usb: hcint 0x00000002, intsts 0x04200029
dwc2 f72c0000.usb: dwc2_update_urb_state_abn(): trimming xfer length
And the usb devices connected are basically hung at this point.
It seems like if we're in host mode, we probably shouldn't run
the dwc2_hostg_ep_disable logic, so this patch returns an error
in that case.
With this patch (along with the previous patch in this set), we avoid
the mismatched interrupts and connected usb devices continue to function.
I'm not sure if some other solution would be better here, but this seems
to work, so I wanted to send it out for input on what the right approach
should be.
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: YongQin Liu <yongqin.liu@linaro.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Tested-by: Minas Harutyunyan <hminas@synopsys.com>
Reported-by: YongQin Liu <yongqin.liu@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In the earlier commit dad3f793f2 ("usb: dwc2: Make sure we
disconnect the gadget state"), I was trying to fix up the
fact that we somehow weren't disconnecting the gadget state,
so that when the OTG port was plugged in the second time we
would get warnings about the state tracking being wrong.
(This seems to be due to a quirk of the HiKey board where
we do not ever get any otg interrupts, particularly the session
end detected signal. Instead we only see status change
interrupt.)
The fix there was somewhat simple, as it just made sure to
call dwc2_hsotg_disconnect() before we connected things up
in OTG mode, ensuring the state handling didn't throw errors.
But in looking at a different issue I was seeing with UDC
state handling, I realized that it would be much better
to call dwc2_hsotg_disconnect when we get the state change
signal moving to host mode.
Thus, this patch removes the earlier disconnect call I added
and moves it (and the needed locking) to the host mode
transition.
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: YongQin Liu <yongqin.liu@linaro.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Tested-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Driver currently notifies only USB2 PHY on USB mode change.
Extend this to USB3 PHY so that PHY drivers based on the
mode can release system resources - clocks, regulators etc.
Additionally Qualcomm QMP and QUSB2 PHY drivers need to
override VBUS signal in PHY wrapper in device mode as USB
VBUS line is not connected to PHYs. Also, remove NULL checks
for PHY when calling phy_set_mode as PHY ops already check this.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Driver currently resumes and increments pm usage_count
of its child device (dwc3 main) from its runtime_resume
handler. This requires dwc3 runtime_resume to perform
pm_runtime_put to decrement the pm usage_count. However
runtime_put from dwc3 happens for non pci drivers
(e.g. dwc3-if-simple.c) as well which results in dwc3
pm usage_count becoming negative after couple of
runtime suspend resume iterations. Fix this by
performing runtime_get/put from dwc3-pci driver only
using workqueue.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Driver powers-off PHYs and reinitializes DWC3 core and gadget on
resume. While this works fine for gadget mode but in host
mode there is not re-initialization of host stack. Also, resetting
bus as part of bus_suspend/resume is not correct which could affect
(or disconnect) connected devices.
Fix this by not reinitializing core on suspend/resume in host mode
for HOST only and OTG/drd configurations.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If devm_extcon_dev_allocate() fails, we should disable clk before return.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Fixes: 860d2686fd ("usb: phy: tahvo: Use devm_extcon_dev_[allocate|register]() and replace deprecated API")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1350962
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1222118
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 703128
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 145713
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
usb_endpoint_maxp() has an inline keyword and searches for bits[10:0]
by & operation with 0x7ff. So, we can remove the duplicate & operation
with 0x7ff.
Signed-off-by: Jaejoong Kim <climbbb.kim@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to all MediaTek SoCs with xHCI host controller use this
driver, remove limitation for specific SoCs
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are mcu_bus and dma_bus clocks needed to be controlled by
driver on some SoCs, so add them as optional ones
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The wakeup debounce clocks for each ports in fact are not
needed, so remove them.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support to disable specific usb3 ports, it's useful when
usb3 phy is shared with PCIe or SATA, because we should disable
the corresponding usb3 port if the phy is used by PCIe or SATA.
Sometimes it's helpful to analyse and solve problems.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is useful to find out the root cause when the Super Speed doesn't
work. Such as when the T-PHY is switched to PCIe or SATA, and affects
Super Speed function, the check will fail.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make use of ports count from xhci but not from ippc in
xhci_mtk_sch_init()
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch uses the simpler dma_set_mask_and_coherent() instead of
doing these as separate steps
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The extcon has two type of extcon devices as following.
- 'extcon provider deivce' adds new extcon device and detect the
state/properties of external connector. Also, it notifies the
state/properties to the extcon consumer device.
- 'extcon consumer device' gets the change state/properties
from extcon provider device.
Prior to that, include/linux/extcon.h contains all exported API for
both provider and consumer device driver. To clarify the meaning of
header file and to remove the wrong use-case on consumer device,
this patch separates into extcon.h and extcon-provider.h.
[Description for include/linux/{extcon.h|extcon-provider.h}]
- extcon.h includes the extcon API and data structure for extcon consumer
device driver. This header file contains the following APIs:
: Register/unregister the notifier to catch the change of extcon device
: Get the extcon device instance
: Get the extcon device name
: Get the state of each external connector
: Get the property value of each external connector
: Get the property capability of each external connector
- extcon-provider.h includes the extcon API and data structure for extcon
provider device driver. This header file contains the following APIs:
: Include 'include/linux/extcon.h'
: Allocate the memory for extcon device instance
: Register/unregister extcon device
: Set the state of each external connector
: Set the property value of each external connector
: Set the property capability of each external connector
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
usb_endpoint_maxp() has an inline keyword and searches for bits[10:0]
by & operation with 0x7ff. So, we can remove the duplicate & operation
with 0x7ff.
Signed-off-by: Jaejoong Kim <climbbb.kim@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
usb_endpoint_maxp() has an inline keyword and searches for bits[10:0]
by & operation with 0x7ff. So, we can remove the duplicate & operation
with 0x7ff.
Signed-off-by: Jaejoong Kim <climbbb.kim@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
usb_endpoint_maxp() has an inline keyword and searches for bits[10:0]
by & operation with 0x7ff. So, we can remove the duplicate & operation
with 0x7ff.
Signed-off-by: Jaejoong Kim <climbbb.kim@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Make config_item_type structures const as they are either passed to a
function having the argument as const or stored in the const "ci_type"
field of a config_item structure.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Make these structures const as they are only passed to the const
argument of the functions config_{group/item}_init_type_name.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add support to get a list of resets available for the device.
These resets must be kept de-asserted until the device is
in use.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
[p.zabel@pengutronix.de: switch to hidden reset control array]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Move clock handling after of_platform_depopulate to achieve
a sequence that is reverse of the probe sequence.
Cc: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If the connect status change is set during reset signaling, but
the status remains connected just retry port reset.
This solves an issue with connecting a 90W HP Thunderbolt 3 dock
with a Lenovo Carbon x1 (5th generation) which causes a 30min loop
of a high speed device being re-discovererd before usb ports starts
working.
[...]
[ 389.023845] usb 3-1: new high-speed USB device number 55 using xhci_hcd
[ 389.491841] usb 3-1: new high-speed USB device number 56 using xhci_hcd
[ 389.959928] usb 3-1: new high-speed USB device number 57 using xhci_hcd
[...]
This is caused by a high speed device that doesn't successfully go to the
enabled state after the second port reset. Instead the connection bounces
(connected, with connect status change), bailing out completely from
enumeration just to restart from scratch.
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1716332
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For the case where an external VBUS is used, we should enable the external
VBUS comparator in the driver. This would prevent an unnecessary
overcurrent error which would then disable the host port.
This patch uses the standard 'disable-over-current' binding to allow of the
option of disabling the over-current condition.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When set otg_sel(SSUSB_U2_PORT_OTG_SEL) for u2port which supports
dual-role mode, the controller will automatically switch mode
between host and device according to IDDIG signal. But if the
u2port only supports device mode, and no IDDIG pin is provided,
setting otg_sel may cause failure of detection by host.
So set it only for dual-role mode.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Treat dr_mode of USB_DR_MODE_UNKNOWN as USB_DR_MODE_OTG to
enhance functional robustness.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When dr_mode is set as USB_DR_MODE_HOST, it's better to try to
get optional vbus, this can increase flexibility, although we
can set vbus as always on for regulator or put it in host driver
to turn it on.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Support SuperSpeedPlus for usb3.1 device IP
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In order to keep manual DRD switch independent on IDDIG interrupt,
make use of FORCE/RG_IDDIG instead of IDDIG EINT interrupt to
implement manual DRD switch function.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
add support for 36-bit DMA address
[ Felipe Balbi: fix printk format for dma_addr_t ]
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There are mcu_bus and dma_bus clocks needed to be turned on/off by
driver on some SoCs, so add them as optional ones
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The wakeup debounce clocks for each ports in fact are not
needed, so remove them.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add support to disable specific usb3 ports, it's useful when
usb3 phy is shared with PCIe or SATA, because we should disable
the corresponding usb3 port if the phy is used by PCIe or SATA.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When failing to get IRQ number, platform_get_irq() may return
-EPROBE_DEFER, but we ignore it and always return -ENODEV,
so fix it.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Many variables in ep0 are set but never used, so should be removed.
Signed-off-by: Christos Gkekas <chris.gekas@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds the dwc2_set_params function for STM32F7xx USB OTG HS.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Make this const as it is only stored in the const field of a structure
video_device in the file referencing it. Make the declaration const too.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use the of_device_get_match_data() helper instead of open coding,
postponing the matching until when it's really needed.
Note that the renesas_usb3 driver is used with DT only, so there's
always a valid match.
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use the of_device_get_match_data() helper instead of open coding.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds support for generic phy as an optional. If you want
to use a generic phy (e.g. phy-rcar-gen3-usb3 driver) on this driver,
you have to do "insmod phy-rcar-gen3-usb3.ko" first for now.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch moves pm_runtime_{en,dis}able() call timing to
renesas_usb3_{probe,remove}() for supporting PM_SLEEP feature in
the future.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
[shimoda: Revise the commit log]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds support for R-Car D3. This SoC needs to release
the PLL reset by the UGCTRL register. So, since this is not the same
as other R-Car Gen3 SoCs, this patch adds a new type as
"USBHS_TYPE_RCAR_GEN3_WITH_PLL".
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch unifies the Gen2 and Gen3 pipe_config setting on
usbhs_parse_dt().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
mxs phy has data pin contact and usb charger detector blocks which
can be controlled by software to detect charger type for SDP, CDP and
DCP.
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that all the information we need sits in struct dwc3_ep, we can
start taking only a pointer to struct dwc3_ep as an argument. This
allows us to clean the code up a bit.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There is more possibility for sharing code if we just realise that now
__dwc3_gadget_kic_transfer() knows to break out early if there are no
TRBs left.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This will let us call __dwc3_gadget_kick_transfer()
unconditionally. No functional changes, cleanup only.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If the clock handle is given in the DT, it means the clock is required
for proper operation of the PHY. In that case a failure to obtain the
clock must be propagated to stop the driver from probing. This fixes
working with clocks, which request probe deferral.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Here's a new metro-usb device id for another bar-code scanner.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=g3Ln
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.14-rc6
Here's a new metro-usb device id for another bar-code scanner.
Signed-off-by: Johan Hovold <johan@kernel.org>
Andrey used the syzkaller fuzzer to find an out-of-bounds memory
access in usb_get_bos_descriptor(). The code wasn't checking that the
next usb_dev_cap_header structure could fit into the remaining buffer
space.
This patch fixes the error and also reduces the bNumDeviceCaps field
in the header to match the actual number of capabilities found, in
cases where there are fewer than expected.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The devices running at SuperSpeedPlus speed are also LPM capable.
Apply usb3 hardware LPM attributes to those devices as well.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This keyboard doesn't implement Get String descriptors properly even
though string indexes are valid. What happens is that when requesting
for the String descriptor, the device disconnects and
reconnects. Without this quirk, this loop will continue forever.
Cc: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Владимир Мартьянов <vilgeforce@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
If the probe fails, udc_remove() will not be called, so there is no
reason to make del_timer_sync() calls conditional. As a result, use of
the .data field can be dropped, in support of making removing this field
entirely from struct timer_list.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Raviteja Garimella <raviteja.garimella@broadcom.com>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: "Gustavo A. R. Silva" <garsilva@embeddedor.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Calls to regmap_read may fail with an -EINVAL return without setting
usbc_irq1 and usbc_irq2. The error handling clean up expects these
to have been set (or zero on a failure) and currently may try to
clear the wrong IRQs if the uninitalized garbage values in usbc_irq1
or usbc_irq2 are non-zero. The simplest fix is to ensure these
variables are initialized to zero.
Detected by CoverityScan, CID#1457737 ("Uninitialized scalar variable")
Fixes: 3c4fb9f169 ("usb: typec: wcove: start using tcpm for USB PD support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a port is unregistered, all the devices attached to it
must be unregistered as well. This will also make sure VBUS
and VCONN are disabled.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: linux-usb@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a kernel oops when unloading the driver due to usb_put_phy
being called after usb_phy_generic_unregister when the device is
detached. Calling usb_phy_generic_unregister causes x->dev->driver to
be NULL in usb_put_phy and results in a NULL pointer dereference.
Cc: stable@vger.kernel.org # v4.3+
Signed-off-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sunxi musb has a bug where sometimes it will generate a babble
error on device disconnect instead of a disconnect IRQ. When this
happens the musb controller switches from host mode to device mode
(it clears MUSB_DEVCTL_HM/MUSB_DEVCTL_SESSION and sets
MUSB_DEVCTL_BDEVICE) and gets stuck in this state.
The babble error is misdetected as a bus reset because MUSB_DEVCTL_HM
was cleared.
To fix this, use is_host_active() rather than (devctl & MUSB_DEVCTL_HM)
to detect babble error so that sunxi musb babble recovery can handle it
by restoring the mode. This information is provided by the driver logic
and does not rely on register contents.
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the number of channels is set to 15 but in the case of DA8xx,
the number of channels is 4.
Update the driver to configure the number of channels at runtime.
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The way to configure the DMA mode on DA8xx is different from DSPS.
Add a new function to configure DMA mode on DA8xx and use a callback
to call the right function based on the platform.
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DA8xx and DSPS platforms don't use the same address for few registers.
On Da8xx, this is causing some issues (e.g. teardown that doesn't work).
Configure the address of the register during the init and use them instead
of constants.
Cc: stable@vger.kernel.org # v4.12+
Reported-by: nsekhar@ti.com
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The musb delayed irq work was never flushed on suspend, something which
since 4.9 can lead to an external abort if the work is scheduled after
the grandparent's clock has been disabled:
PM: Suspending system (mem)
PM: suspend of devices complete after 125.224 msecs
PM: suspend devices took 0.132 seconds
PM: late suspend of devices complete after 7.423 msecs
PM: noirq suspend of devices complete after 7.083 msecs
suspend debug: Waiting for 5 second(s).
Unhandled fault: external abort on non-linefetch (0x1008) at 0xd0262c60
...
[<c054880c>] (musb_default_readb) from [<c0547b5c>] (musb_irq_work+0x48/0x220)
[<c0547b5c>] (musb_irq_work) from [<c014f8a4>] (process_one_work+0x1f4/0x758)
[<c014f8a4>] (process_one_work) from [<c014fe5c>] (worker_thread+0x54/0x514)
[<c014fe5c>] (worker_thread) from [<c015704c>] (kthread+0x128/0x158)
[<c015704c>] (kthread) from [<c0109330>] (ret_from_fork+0x14/0x24)
Commit 2bff3916fd ("usb: musb: Fix PM for hub disconnect") started
scheduling musb_irq_work with a delay of up to a second and with
retries thereby making this easy to trigger, for example, by suspending
shortly after a disconnect.
Note that we set a flag to prevent the irq work from rescheduling itself
during suspend and instead process a disconnect immediately. This takes
care of the case where we are disconnected shortly before suspending.
However, when in host mode, a disconnect while suspended will still
go unnoticed and thus prevent the controller from runtime suspending
upon resume as the session bit is always set. This will need to be
addressed separately.
Fixes: 550a7375fe ("USB: Add MUSB and TUSB support")
Fixes: 467d5c9807 ("usb: musb: Implement session bit based runtime PM for musb-core")
Fixes: 2bff3916fd ("usb: musb: Fix PM for hub disconnect")
Cc: stable <stable@vger.kernel.org> # 4.9
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current session-bit quirk implementation does not prevent the retry
counter from underflowing, something which could break runtime PM and
keep the device active for a very long time (about 2^32 seconds) after a
disconnect.
This notably breaks the B-device timeout case, but could potentially
cause problems also when the controller is operating as an A-device.
Fixes: 2bff3916fd ("usb: musb: Fix PM for hub disconnect")
Cc: stable <stable@vger.kernel.org> # 4.9
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Elatec TWN3 has the union descriptor on data interface. This results in
failure to bind the device to the driver with the following log:
usb 1-1.2: new full speed USB device using streamplug-ehci and address 4
usb 1-1.2: New USB device found, idVendor=09d8, idProduct=0320
usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-1.2: Product: RFID Device (COM)
usb 1-1.2: Manufacturer: OEM
cdc_acm 1-1.2:1.0: Zero length descriptor references
cdc_acm: probe of 1-1.2:1.0 failed with error -22
Adding the NO_UNION_NORMAL quirk for the device fixes the issue.
`lsusb -v` of the device:
Bus 001 Device 003: ID 09d8:0320
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 2 Communications
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 32
idVendor 0x09d8
idProduct 0x0320
bcdDevice 3.00
iManufacturer 1 OEM
iProduct 2 RFID Device (COM)
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 67
bNumInterfaces 2
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 250mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 1 AT-commands (v.25ter)
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0020 1x 32 bytes
bInterval 2
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 10 CDC Data
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0020 1x 32 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0020 1x 32 bytes
bInterval 0
CDC Header:
bcdCDC 1.10
CDC Call Management:
bmCapabilities 0x03
call management
use DataInterface
bDataInterface 1
CDC ACM:
bmCapabilities 0x06
sends break
line coding and serial state
CDC Union:
bMasterInterface 0
bSlaveInterface 1
Device Status: 0x0000
(Bus Powered)
Signed-off-by: Maksim Salau <msalau@iotecha.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Taking the uurb->buffer_length userspace passes in as a maximum for the
actual urbs transfer_buffer_length causes 2 serious issues:
1) It breaks isochronous support for all userspace apps using libusb,
as existing libusb versions pass in 0 for uurb->buffer_length,
relying on the kernel using the lenghts of the usbdevfs_iso_packet_desc
descriptors passed in added together as buffer length.
This for example causes redirection of USB audio and Webcam's into
virtual machines using qemu-kvm to no longer work. This is a userspace
ABI break and as such must be reverted.
Note that the original commit does not protect other users / the
kernels memory, it only stops the userspace process making the call
from shooting itself in the foot.
2) It may cause the kernel to program host controllers to DMA over random
memory. Just as the devio code used to only look at the iso_packet_desc
lenghts, the host drivers do the same, relying on the submitter of the
urbs to make sure the entire buffer is large enough and not checking
transfer_buffer_length.
But the "USB: devio: Don't corrupt user memory" commit now takes the
userspace provided uurb->buffer_length for the buffer-size while copying
over the user-provided iso_packet_desc lengths 1:1, allowing the user
to specify a small buffer size while programming the host controller to
dma a lot more data.
(Atleast the ohci, uhci, xhci and fhci drivers do not check
transfer_buffer_length for isoc transfers.)
This reverts commit fa1ed74eb1 ("USB: devio: Don't corrupt user memory")
fixing both these issues.
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_stop_device() calls xhci_queue_stop_endpoint() multiple times
without checking the return value. xhci_queue_stop_endpoint() can
return error if the HC is already halted or unable to queue commands.
This can cause a deadlock condition as xhci_stop_device() would
end up waiting indefinitely for a completion for the command that
didn't get queued. Fix this by checking the return value and bailing
out of xhci_stop_device() in case of error. This patch happens to fix
potential memory leaks of the allocated command structures as well.
Fixes: c311e391a7 ("xhci: rework command timeout and cancellation,")
Cc: <stable@vger.kernel.org>
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a URB is cancled, xhci driver turns the untransferred trbs
into no-ops. If an endpoint stalls on a no-op trb that belongs
to the cancelled URB, the event handler won't reset the endpoint.
Hence, it will stay halted.
Link: http://marc.info/?l=linux-usb&m=149582598330127&w=2
Cc: <stable@vger.kernel.org>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KASAN reported use-after-free bug when xhci host controller died:
[ 176.952537] BUG: KASAN: use-after-free in xhci_handle_command_timeout+0x68/0x224
[ 176.960846] Write of size 4 at addr ffffffc0cbb01608 by task kworker/3:3/1680
...
[ 177.180644] Freed by task 0:
[ 177.183882] kasan_slab_free+0x90/0x15c
[ 177.188194] kfree+0x114/0x28c
[ 177.191630] xhci_cleanup_command_queue+0xc8/0xf8
[ 177.196916] xhci_hc_died+0x84/0x358
Problem here is that when the cmd_timer fired, it would try to access
current_cmd while the command queue is already freed by xhci_hc_died().
Cleanup current_cmd in xhci_cleanup_command_queue() to avoid that.
Fixes: d9f11ba9f1 ("xhci: Rework how we handle unresponsive or hoptlug removed hosts")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many USB 3.1 capable hosts never updated the Serial Bus Release Number
(SBRN) register to USB 3.1 from USB 3.0
xhci driver identified USB 3.1 capable hosts based on this SBRN register,
which according to specs "contains the release of the Universal Serial
Bus Specification with which this Universal Serial Bus Host Controller
module is compliant." but still in october 2017 gives USB 3.0 as
the only possible option.
Make an additional check for USB 3.1 support and enable it if the xHCI
supported protocol capablity lists USB 3.1 capable ports.
Cc: <stable@vger.kernel.org> # v4.6+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add device-id entry for (Honeywell) Metrologic MS7820 bar code scanner.
The device has two interfaces (in this mode?); a vendor-specific
interface with two interrupt endpoints and a second HID interface, which
we do not bind to.
Reported-by: Ladislav Dobrovsky <ladislav.dobrovsky@gmail.com>
Tested-by: Ladislav Dobrovsky <ladislav.dobrovsky@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop the usb-serial-core USB driver that was registered at module init
but then never used.
This was a remnant dating back to 2004 (!) when this struct usb_driver
was used for the generic driver; see commit bbc53b7d7322 ("USB: fix bug
where removing usb-serial modules or usb serial devices could oops") in
the tglx bitkeeper-history archive.
Note that every usb-serial driver (including the generic one) registers
its own USB (interface) driver along with its usb-serial bus drivers.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
One class of "unidirectional" devices managed by this driver uses an
interrupt-out endpoint to send control messages at open and close. Due
to a missing endpoint sanity check, this could result in an interrupt
URB being submitted to endpoint 0 instead. This would be caught by
USB core (without a WARN dump), but let's verify that the expected
endpoints are present at probe rather than when a port is later opened.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Let usb-serial core verify that the interrupt-in endpoint is present
when binding the interface instead of the driver verifying this at every
open.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to kill the interrupt-in URB after a failed open request.
Apart from saving power (and avoiding stale input after a later
successful open), this also prevents a NULL-deref in the completion
handler if the port is manually unbound.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 704577861d ("USB: serial: metro-usb: get data from device in Uni-Directional mode.")
Cc: stable <stable@vger.kernel.org> # 3.5
Signed-off-by: Johan Hovold <johan@kernel.org>
A deadlock fix in dummy-hcd; Fixing a use-after-free bug in composite;
Renesas got another fix for DMA programming (this time around a fix
for receiving ZLP); Tegra PHY got a suspend fix; A memory leak on our
configfs ABI got plugged.
Other than these, a couple other minor fixes on usbtest.
-----BEGIN PGP SIGNATURE-----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=uGcr
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
USB: fixes for v4.14-rc5
A deadlock fix in dummy-hcd; Fixing a use-after-free bug in composite;
Renesas got another fix for DMA programming (this time around a fix
for receiving ZLP); Tegra PHY got a suspend fix; A memory leak on our
configfs ABI got plugged.
Other than these, a couple other minor fixes on usbtest.
Clean up the somewhat convoluted init-session logic to improve
readability.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Use the port device for any init-session error and debug messages,
remove one redundant debug message and simplify one error message.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop out-commented timer expiry initialisation which would not even
compile anymore.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to free the port private data before returning after a failed
probe attempt.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to stop any submitted interrupt and bulk-out URBs before
returning after failed probe and when the port is being unbound to avoid
later NULL-pointer dereferences in the completion callbacks.
Also fix up the related and broken I/O cancellation on failed open and
on close. (Note that port->write_urb was never submitted.)
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org> # 51a2f077 ("USB: introduce usb_anchor")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This patch adds a new helper function to perform a sanity check of the
given URB to see whether it contains a valid endpoint. It's a light-
weight version of what usb_submit_urb() does, but without the kernel
warning followed by the stack trace, just returns an error code.
Especially for a driver that doesn't parse the descriptor but fills
the URB with the fixed endpoint (e.g. some quirks for non-compliant
devices), this kind of check is preferable at the probe phase before
actually submitting the urb.
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the usbtest driver encounters a device with an IN bulk endpoint but
no OUT bulk endpoint, it will try to dereference a NULL pointer
(out->desc.bEndpointAddress). The problem can be solved by adding a
missing test.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Kmemleak checking configuration reports a memory leak in
usb_os_desc_prepare_interf_dir function when rndis function
instance is freed and then allocated again. For example, this
happens with FunctionFS driver with RNDIS function enabled
when "ffs-test" test application is run several times in a row.
The data for intermediate "os_desc" group for interface directories
is allocated as a single VLA chunk and (after a change of default
groups handling) is not ever freed and actually not stored anywhere
besides inside a list of default groups of a parent group.
The fix is to make usb_os_desc_prepare_interf_dir function return
a pointer to allocated data (as a pointer to the first VLA item)
instead of (an unused) integer and to make the caller component
(currently the only one is RNDIS function) responsible for storing
the pointer and freeing the memory when appropriate.
Fixes: 1ae1602de0 ("configfs: switch ->default groups to a linked list")
Cc: stable@vger.kernel.org
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
KASAN enabled configuration reports an error
BUG: KASAN: use-after-free in usb_composite_overwrite_options+...
[libcomposite] at addr ...
Read of size 1 by task ...
when some driver is un-bound and then bound again.
For example, this happens with FunctionFS driver when "ffs-test"
test application is run several times in a row.
If the driver has empty manufacturer ID string in initial static data,
it is then replaced with generated string. After driver unbinding
the generated string is freed, but the driver data still keep that
pointer. And if the driver is then bound again, that pointer
is re-used for string emptiness check.
The fix is to clean up the driver string data upon its unbinding
to drop the pointer to freed memory.
Fixes: cc2683c318 ("usb: gadget: Provide a default implementation of default manufacturer string")
Cc: stable@vger.kernel.org
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There used to be a test against "if (param->sglen > MAX_SGLEN)" but it
was removed during a refactor. It leads to an integer overflow and a
stack overflow in test_queue() if we try to create a too large urbs[]
array on the stack.
There is a second integer overflow in test_queue() as well if
"param->iterations" is too high. I don't immediately see that it's
harmful but I've added a check to prevent it and silence the static
checker warning.
Fixes: 18fc4ebdc7 ("usb: misc: usbtest: Remove timeval usage")
Acked-by: Deepa Dinamani <deepa.kernel@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The DREQE bit of the DnFIFOSEL should be set to 1 after the DE bit of
USB-DMAC on R-Car SoCs is set to 1 after the USB-DMAC received a
zero-length packet. Otherwise, a transfer completion interruption
of USB-DMAC doesn't happen. Even if the driver changes the sequence,
normal operations (transmit/receive without zero-length packet) will
not cause any side-effects. So, this patch fixes the sequence anyway.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
[shimoda: revise the commit log]
Fixes: e73a9891b3 ("usb: renesas_usbhs: add DMAEngine support")
Cc: <stable@vger.kernel.org> # v3.1+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The dummy-hcd driver calls the gadget driver's disconnect callback
under the wrong conditions. It should invoke the callback when Vbus
power is turned off, but instead it does so when the D+ pullup is
turned off.
This can cause a deadlock in the composite core when a gadget driver
is unregistered:
[ 88.361471] ============================================
[ 88.362014] WARNING: possible recursive locking detected
[ 88.362580] 4.14.0-rc2+ #9 Not tainted
[ 88.363010] --------------------------------------------
[ 88.363561] v4l_id/526 is trying to acquire lock:
[ 88.364062] (&(&cdev->lock)->rlock){....}, at: [<ffffffffa0547e03>] composite_disconnect+0x43/0x100 [libcomposite]
[ 88.365051]
[ 88.365051] but task is already holding lock:
[ 88.365826] (&(&cdev->lock)->rlock){....}, at: [<ffffffffa0547b09>] usb_function_deactivate+0x29/0x80 [libcomposite]
[ 88.366858]
[ 88.366858] other info that might help us debug this:
[ 88.368301] Possible unsafe locking scenario:
[ 88.368301]
[ 88.369304] CPU0
[ 88.369701] ----
[ 88.370101] lock(&(&cdev->lock)->rlock);
[ 88.370623] lock(&(&cdev->lock)->rlock);
[ 88.371145]
[ 88.371145] *** DEADLOCK ***
[ 88.371145]
[ 88.372211] May be due to missing lock nesting notation
[ 88.372211]
[ 88.373191] 2 locks held by v4l_id/526:
[ 88.373715] #0: (&(&cdev->lock)->rlock){....}, at: [<ffffffffa0547b09>] usb_function_deactivate+0x29/0x80 [libcomposite]
[ 88.374814] #1: (&(&dum_hcd->dum->lock)->rlock){....}, at: [<ffffffffa05bd48d>] dummy_pullup+0x7d/0xf0 [dummy_hcd]
[ 88.376289]
[ 88.376289] stack backtrace:
[ 88.377726] CPU: 0 PID: 526 Comm: v4l_id Not tainted 4.14.0-rc2+ #9
[ 88.378557] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014
[ 88.379504] Call Trace:
[ 88.380019] dump_stack+0x86/0xc7
[ 88.380605] __lock_acquire+0x841/0x1120
[ 88.381252] lock_acquire+0xd5/0x1c0
[ 88.381865] ? composite_disconnect+0x43/0x100 [libcomposite]
[ 88.382668] _raw_spin_lock_irqsave+0x40/0x54
[ 88.383357] ? composite_disconnect+0x43/0x100 [libcomposite]
[ 88.384290] composite_disconnect+0x43/0x100 [libcomposite]
[ 88.385490] set_link_state+0x2d4/0x3c0 [dummy_hcd]
[ 88.386436] dummy_pullup+0xa7/0xf0 [dummy_hcd]
[ 88.387195] usb_gadget_disconnect+0xd8/0x160 [udc_core]
[ 88.387990] usb_gadget_deactivate+0xd3/0x160 [udc_core]
[ 88.388793] usb_function_deactivate+0x64/0x80 [libcomposite]
[ 88.389628] uvc_function_disconnect+0x1e/0x40 [usb_f_uvc]
This patch changes the code to test the port-power status bit rather
than the port-connect status bit when deciding whether to isue the
callback.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: David Tulloh <david@tulloh.id.au>
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Commit dfebb5f43a ("usb: chipidea: Add support for Tegra20/30/114/124")
added UDC support for Tegra but with UDC support enabled, is was found
that Tegra30, Tegra114 and Tegra124 would hang on entry to suspend.
The hang occurred during the suspend of the USB PHY when the Tegra PHY
driver attempted to disable the PHY clock. The problem is that before
the Tegra PHY driver is suspended, the chipidea driver already disabled
the PHY clock and when the Tegra PHY driver suspended, it could not read
DEVLC register and caused the device to hang.
The Tegra USB PHY driver is used by both the Tegra EHCI driver and now
the chipidea UDC driver and so simply removing the disabling of the PHY
clock from the USB PHY driver would not work for the Tegra EHCI driver.
Fortunately, the status of the USB PHY clock can be read from the
USB_SUSP_CTRL register and therefore, to workaround this issue, simply
poll the register prior to disabling the clock in USB PHY driver to see
if clock gating has already been initiated. Please note that it can take
a few uS for the clock to disable and so simply reading this status
register once on entry is not sufficient.
Similarly when turning on the PHY clock, it is possible that the clock
is already enabled or in the process of being enabled, and so check for
this when enabling the PHY.
Please note that no issues are seen with Tegra20 because it has a slightly
different PHY to Tegra30/114/124.
Fixes: dfebb5f43a ("usb: chipidea: Add support for Tegra20/30/114/124")
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The dummy-hcd driver doesn't support emulation of isochronous
transfers. Therefore it doesn't need to export isochronous endpoint
descriptors; they can be commented out.
Also, the comments in the source code don't express clearly enough the
fact that isochronous isn't supported. They need to be more explicit.
Finally, change the error status value we use (in theory) for
isochronous URBs. checkpatch complains about ENOSYS; EINVAL is more
appropriate (it is documented to mean "ISO madness").
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Part of the emulation performed by dummy-hcd is accounting for
bandwidth utilization. The total amount of data transferred in a
single frame is supposed to be no larger than an actual USB connection
could accommodate.
Currently the driver performs bandwidth limiting only for bulk
transfers; control and periodic transfers are effectively unlimited.
(Presumably drivers were not expected to request extremely large
control or interrupt transfers.) This patch improves the situation
somewhat by restricting them as well.
The emulation still isn't perfect. On a real system, even 0-length
transfers use some bandwidth because of transaction overhead
(IN, OUT, ACK, NACK packets) and packet overhead (SYNC, PID, bit
stuffing, CRC, EOP). Adding in those factors is left as an exercise
for a later patch.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Johan Hovold <johan@kernel.org>
Cc: Allen Pais <allen.lkml@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Here's a fix for a cp210x regression that prevented a class of devices
from being successfully probed. Two use-after-free bugs in the console
code are also fixed.
Included are also some new device ids.
All but the last three commits have been in linux-next with no reported
issues.
-----BEGIN PGP SIGNATURE-----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=GjJU
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.14-rc5
Here's a fix for a cp210x regression that prevented a class of devices
from being successfully probed. Two use-after-free bugs in the console
code are also fixed.
Included are also some new device ids.
All but the last three commits have been in linux-next with no reported
issues.
Make sure to reset the USB-console port pointer when console setup fails
in order to avoid having the struct usb_serial be prematurely freed by
the console code when the device is later disconnected.
Fixes: 73e487fdb7 ("[PATCH] USB console: fix disconnection issues")
Cc: stable <stable@vger.kernel.org> # 2.6.18
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
A clean-up patch removing two redundant NULL-checks from the console
disconnect handler inadvertently also removed a third check. This could
lead to the struct usb_serial being prematurely freed by the console
code when a driver accepts but does not register any ports for an
interface which also lacks endpoint descriptors.
Fixes: 0e517c93dc ("USB: serial: console: clean up sanity checks")
Cc: stable <stable@vger.kernel.org> # 4.11
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Use the of_device_get_match_data() helper instead of open coding.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
inc_deq() currently bails earlier for EVENT rings than the common return
point of the function, due to the fact that EVENT rings do not have
link TRBs. The unfortunate side effect of this is that the very useful
trace_xhci_inc_deq() function is not called/usable for EVENT ring
debug.
This patch provides a refactor by removing the multiple return exit
points into a single return which additionally allows for all rings to
use the trace function.
Signed-off-by: Adam Wallis <awallis@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch will improve the variable auto-resume latency of an usb-port.
The attempt to sync the start of root hub polling with resume time
signaling finish was ruined by a later request to start immediate
root hub polling.
When xhci gets a port status change event interrupt due to PORT_PLC
(port link state transition), linux Host controller driver drives the
resume signalling on the bus for the amount of time defined by
USB_REUME_TIMEOUT(40ms) macro.
This 40ms delay for resume signalling is in acceptable limit, but
it get worse when xhci goes for polling mode in order to detect other
events on its ports and modify rh_timer timer with a variable time out of
1ms to (HZ/4)ms.
drivers/usb/core/hcd.c line 799
mod_timer (&hcd->rh_timer, (jiffies/(HZ/4) + 1) * (HZ/4)).
Due to above variable timeout usb auto-resume latency varies from
40ms to ~300ms.
Log Snippet:
~128ms latency
[ 53.112049] hub 1-0:1.0: state 7 ports 12 chg 0000 evt 0000
[ 53.229200] hub 1-0:1.0: state 7 ports 12 chg 0000 evt 0004
[ 53.240177] usb 1-2: usb wakeup-resume
[ 53.240195] usb 1-2: finish resume
[ 53.240357] usb usb1-port2: resume, status 0
-----------------------------------------------------------------
~300ms latency
[ 59.946620] hub 1-0:1.0: state 7 ports 12 chg 0000 evt 0000
[ 59.979341] hub 1-0:1.0: state 7 ports 12 chg 0000 evt 0000
[ 60.229342] hub 1-0:1.0: state 7 ports 12 chg 0000 evt 0004
[ 60.251321] usb 1-2: usb wakeup-resume
[ 60.251335] usb 1-2: finish resume
[ 60.251539] usb usb1-port2: resume, status 0
This variable resume latency can be optimized, as in case of PORT_PLC
change event rh_timer has already been modified with USB_RESUME_TIMEOUT
(40ms) delay,leaving the rest to GetPortStatus and started polling for
root hub status (invoking usb_hcd_poll_rh_status).
We can avoid polling as we have already modified rh_timer with
delay of 40ms.
This patch set the HCD_FLAG_POLL_RH to hcd->flags after modification of
rh_timer, and avoids polling of root hub status. so rh_timer can fire
after 40ms and usb device auto-resuem latency will be around 40ms.
[topic and first two senctences of commit message changed -Mathias]
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xhci driver handles USB transaction errors on transfer events,
but transaction errors are possible on address device command
completion events as well.
The xHCI specification (section 4.6.5) says: A USB Transaction
Error Completion Code for an Address Device Command may be due
to a Stall response from a device. Software should issue a Disable
Slot Command for the Device Slot then an Enable Slot Command to
recover from this error.
This patch handles USB transaction errors on address command
completion events. The related discussion threads can be found
through below links.
http://marc.info/?l=linux-usb&m=149362010728921&w=2http://marc.info/?l=linux-usb&m=149252752825755&w=2
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci->mutex was added in xhci_alloc_dev() to protect two race sources
(xhci->slot_id and xhci->addr_dev) by commit a00918d052 ("usb: host:
xhci: add mutex for non-thread-safe data").
While xhci->slot_id has been discarded in commit c2d3d49bba ("usb:
xhci: move slot_id from xhci_hcd to xhci_command structure"), and
xhci->addr_dev has been removed in commit 87e44f2aac ("usb: xhci:
remove the use of xhci->addr_dev"), it's now safe to remove the use of
xhci->mutex in xhci_alloc_dev().
Link: https://marc.info/?l=linux-usb&m=150306294725821&w=2
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_disable_slot() is a helper for disabling a slot when a device
goes away or recovers from error situations. Currently, it returns
success when it sees a dead host. This is not the right way to go.
It should return error and let the invoker know that disable slot
command was failed due to a dead host.
Fixes: f9e609b824 ("usb: xhci: Add helper function xhci_disable_slot().")
Cc: Guoqing Zhang <guoqing.zhang@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If xhci_disable_slot() returns success, a disable slot command
trb was queued in the command ring. The command completion
handler will free the virtual device data structure associated
with the slot. On the other hand, when xhci_disable_slot()
returns error, the invokers should take the responsibilities to
free the slot related data structure. Otherwise, memory leakage
happens.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_disable_slot() allows the invoker to pass a command pointer
as paramenter. Otherwise, it will allocate one. This will cause
memory leak when a command structure was allocated inside of this
function while queuing command trb fails. Another problem comes up
when the invoker passed a command pointer, but xhci_disable_slot()
frees it when it detects a dead host.
This patch fixes these two problems by removing the command parameter
from xhci_disable_slot().
Fixes: f9e609b824 ("usb: xhci: Add helper function xhci_disable_slot().")
Cc: Guoqing Zhang <guoqing.zhang@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_disable_slot() is a helper for disabling a slot when a device
goes away or recovers from error situations. Currently, it checks
the corespoding virt-dev pointer and returns directly (w/o issuing
disable slot command) if it's null.
This is unnecessary and will cause problems in case where virt-dev
allocation fails and xhci_disable_slot() is called to roll back the
hardware state. Refer to the implementation of xhci_alloc_dev().
This patch removes lines to check virt-dev in xhci_disable_slot().
Fixes: f9e609b824 ("usb: xhci: Add helper function xhci_disable_slot().")
Cc: Guoqing Zhang <guoqing.zhang@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds debugfs consumer for xHCI driver. The debugfs entries
read all host registers, device/endpoint contexts, command ring,
event ring and various endpoint rings. With these entries, users
can check the registers and memory spaces used by a host during
run time, or save all the information with a simple 'cp -r' for
post-mortem programs.
The file hierarchy looks like this.
[root of debugfs]
|__usb
|____[e,u,o]hci <---------[root for other HCIs]
|____xhci <---------------[root for xHCI]
|______0000:00:14.0 <--------------[xHCI host name]
|________reg-cap <--------[capability registers]
|________reg-op <-------[operational registers]
|________reg-runtime <-----------[runtime registers]
|________reg-ext-#cap_name <----[extended capability regs]
|________command-ring <-------[root for command ring]
|__________cycle <------------------[ring cycle]
|__________dequeue <--------[ring dequeue pointer]
|__________enqueue <--------[ring enqueue pointer]
|__________trbs <-------------------[ring trbs]
|________event-ring <---------[root for event ring]
|__________cycle <------------------[ring cycle]
|__________dequeue <--------[ring dequeue pointer]
|__________enqueue <--------[ring enqueue pointer]
|__________trbs <-------------------[ring trbs]
|________devices <------------[root for devices]
|__________#slot_id <-----------[root for a device]
|____________name <-----------------[device name]
|____________slot-context <----------------[slot context]
|____________ep-context <-----------[endpoint contexts]
|____________ep#ep_index <--------[root for an endpoint]
|______________cycle <------------------[ring cycle]
|______________dequeue <--------[ring dequeue pointer]
|______________enqueue <--------[ring enqueue pointer]
|______________trbs <-------------------[ring trbs]
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
XHCI specification 1.1 does not require xHCI-compliant controllers
to always enable hardware USB2 LPM. However, the current xHCI
driver always enable it when seeing HLC=1.
This patch supports an option for users to control disabling
USB2 Hardware LPM via DT/ACPI attribute.
This option is needed in case user would like to disable this
feature. For example, their xHCI controller has its USB2 HW LPM
broken.
Signed-off-by: Tung Nguyen <tunguyen@apm.com>
Signed-off-by: Thang Q. Nguyen <tqnguyen@apm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When an Atmel SoC is suspended with the backup mode, the USB bus will be
powered down. As this is expected, do not return an error to the driver
core when ehci_resume detects it.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the special SA1111 MMIO accessors from the ohci-sa1111 driver
as their definition will be removed shortly. The SA1111 accessors are
barrierless, so use the _relaxed variants.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert the shutdown method to use the device_driver shutdown function
pointer rather than a private bus-type shutdown. This is the only user
for SA1111 bus types, so having the support code in the bus doesn't
make any sense.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the provided sa1111_get_irq() to fetch the IRQ resources for the
SA1111 OHCI driver.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver for TI TPS65982, TPS65983 and other TPS6598x family
stand alone USB Power Delivery controllers.
The driver will at this stage only register the port and
partners attached to it, so cables and alternate modes are
not yet registered. Both power and data role swapping is
supported.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch makes the driver work with USB Type-C Port
Manager (tcpm.c) to provide USB PD functionality.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .data assignment appears to be redundant to the WORK_STOP bit for
stopping the timer. Also, it appears this timer is entirely unused
as it is only ever started under #define VERBOSE, which is explicitly
undefined.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds support for devicetree to the max3421 driver.
Signed-off-by: Jules Maselbas <jules.maselbas@grenoble-inp.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dell Wireless 5819/5818 devices are re-branded Sierra Wireless MC74
series which will by default boot with vid 0x413c and pid's 0x81cf,
0x81d0, 0x81d1, 0x81d2.
Signed-off-by: Shrirang Bagul <shrirang.bagul@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add compatible string to use this generic glue layer to support
Spreadtrum SC9860 platform's dwc3 controller.
Signed-off-by: Baolin Wang <baolin.wang@spreadtrum.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The driver triggers actions on both edges of the vbus signal.
The former PIO controller was triggering IRQs on both falling and rising edges
by default. Newer PIO controller don't, so it's better to set it explicitly to
IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING.
Without this patch we may trigger the connection with host but only on some
bouncing signal conditions and thus lose connecting events.
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: stable <stable@vger.kernel.org> # v4.4+
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
By submitting completed transfers to the system workqueue there is no
guarantee that completion events will be queued up in the correct order,
as in multi-processor systems there is a thread running for each
processor and the work items are not bound to a particular core.
This means that several completions are in the queue at the same time,
they may be processed in parallel and complete out of order, resulting
in data appearing corrupt when read by userspace.
Create a single-threaded workqueue for FunctionFS so that data completed
requests is passed to userspace in the order in which they complete.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes an issue that the usbhsf_fifo_clear() is possible
to cause 10 msec delay if the pipe is RX direction and empty because
the FRDY bit will never be set to 1 in such case.
Fixes: e8d548d549 ("usb: renesas_usbhs: fifo became independent from pipe.")
Cc: <stable@vger.kernel.org> # v3.1+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes an issue that the driver sets the BCLR bit of
{C,Dn}FIFOCTR register to 1 even when it's non-DCP pipe and
the FRDY bit of {C,Dn}FIFOCTR register is set to 1.
Fixes: e8d548d549 ("usb: renesas_usbhs: fifo became independent from pipe.")
Cc: <stable@vger.kernel.org> # v3.1+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes an issue that this driver cannot go status stage
in control read when the req.zero is set to 1 and the len in
usb3_write_pipe() is set to 0. Otherwise, if we use g_ncm driver,
usb enumeration takes long time (5 seconds or more).
Fixes: 746bfe63bb ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
According to the datasheet of R-Car Gen3, the Pn_RAMMAP.Pn_MPKT should
be set to one of 8, 16, 32, 64, 512 and 1024. Otherwise, when a gadget
driver uses an interrupt endpoint, unexpected behavior happens. So,
this patch fixes it.
Fixes: 746bfe63bb ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When bRequestType & USB_DIR_IN is false and req.length is 0 in control
transfer, since it means non-data, this driver should not set the mode
as control write. So, this patch fixes it.
Fixes: 746bfe63bb ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
A recent change to the synchronization in dummy-hcd was incorrect.
The issue was that dummy_udc_stop() contained no locking and therefore
could race with various gadget driver callbacks, and the fix was to
add locking and issue the callbacks with the private spinlock held.
UDC drivers aren't supposed to do this. Gadget driver callback
routines are allowed to invoke functions in the UDC driver, and these
functions will generally try to acquire the private spinlock. This
would deadlock the driver.
The correct solution is to drop the spinlock before issuing callbacks,
and avoid races by emulating the synchronize_irq() call that all real
UDC drivers must perform in their ->udc_stop() routines after
disabling interrupts. This involves adding a flag to dummy-hcd's
private structure to keep track of whether interrupts are supposed to
be enabled, and adding a counter to keep track of ongoing callbacks so
that dummy_udc_stop() can wait for them all to finish.
A real UDC driver won't receive disconnect, reset, suspend, resume, or
setup events once it has disabled interrupts. dummy-hcd will receive
them but won't try to issue any gadget driver callbacks, which should
be just as good.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: f16443a034 ("USB: gadgetfs, dummy-hcd, net2280: fix locking for callbacks")
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The dummy-hcd HCD/UDC emulator tries not to do too much work during
each timer interrupt. But it doesn't try very hard; currently all
it does is limit the total amount of bulk data transferred. Other
transfer types aren't limited, and URBs that transfer no data (because
of an error, perhaps) don't count toward the limit, even though on a
real USB bus they would consume at least a minimum overhead.
This means it's possible to get the driver stuck in an infinite loop,
for example, if the host class driver resubmits an URB every time it
completes (which is common for interrupt URBs). Each time the URB is
resubmitted it gets added to the end of the pending-URBs list, and
dummy-hcd doesn't stop until that list is empty. Andrey Konovalov was
able to trigger this failure mode using the syzkaller fuzzer.
This patch fixes the infinite-loop problem by restricting the URBs
handled during each timer interrupt to those that were already on the
pending list when the interrupt routine started. Newly added URBs
won't be processed until the next timer interrupt. The problem of
properly accounting for non-bulk bandwidth (as well as packet and
transaction overhead) is not addressed here.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The dummy-hcd UDC driver is not careful about the way it handles
connection speeds. It ignores the module parameter that is supposed
to govern the maximum connection speed and it doesn't set the HCD
flags properly for the case where it ends up running at full speed.
The result is that in many cases, gadget enumeration over dummy-hcd
fails because the bMaxPacketSize byte in the device descriptor is set
incorrectly. For example, the default settings call for a high-speed
connection, but the maxpacket value for ep0 ends up being set for a
Super-Speed connection.
This patch fixes the problem by initializing the gadget's max_speed
and the HCD flags correctly.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The driver will forward errors to userspace after turning most of them
into -EIO. But all status codes are not equal. The -EPIPE (stall) in
particular can be seen more as a result of normal USB signaling than
an actual error. The state is automatically cleared by the USB core
without intervention from either driver or userspace.
And most devices and firmwares will never trigger a stall as a result
of GetEncapsulatedResponse. This is in fact a requirement for CDC WDM
devices. Quoting from section 7.1 of the CDC WMC spec revision 1.1:
The function shall not return STALL in response to
GetEncapsulatedResponse.
But this driver is also handling GetEncapsulatedResponse on behalf of
the qmi_wwan and cdc_mbim drivers. Unfortunately the relevant specs
are not as clear wrt stall. So some QMI and MBIM devices *will*
occasionally stall, causing the GetEncapsulatedResponse to return an
-EPIPE status. Translating this into -EIO for userspace has proven to
be harmful. Treating it as an empty read is safer, making the driver
behave as if the device was conforming to the CDC WDM spec.
There have been numerous reports of issues related to -EPIPE errors
from some newer CDC MBIM devices in particular, like for example the
Fibocom L831-EAU. Testing on this device has shown that the issues
go away if we simply ignore the -EPIPE status. Similar handling of
-EPIPE is already known from e.g. usb_get_string()
The -EPIPE log message is still kept to let us track devices with this
unexpected behaviour, hoping that it attracts attention from firmware
developers.
Cc: <stable@vger.kernel.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100938
Reported-and-tested-by: Christian Ehrig <christian.ehrig@mediamarktsaturn-bt.com>
Reported-and-tested-by: Patrick Chilton <chpatrick@gmail.com>
Reported-and-tested-by: Andreas Böhler <news@aboehler.at>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The user buffer has "uurb->buffer_length" bytes. If the kernel has more
information than that, we should truncate it instead of writing past
the end of the user's buffer. I added a WARN_ONCE() to help the user
debug the issue.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There used to be an integer overflow check in proc_do_submiturb() but
we removed it. It turns out that it's still required. The
uurb->buffer_length variable is a signed integer and it's controlled by
the user. It can lead to an integer overflow when we do:
num_sgs = DIV_ROUND_UP(uurb->buffer_length, USB_SG_SIZE);
If we strip away the macro then that line looks like this:
num_sgs = (uurb->buffer_length + USB_SG_SIZE - 1) / USB_SG_SIZE;
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
It's the first addition which can overflow.
Fixes: 1129d270cb ("USB: Increase usbfs transfer limit")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As a holdover from the old g_file_storage gadget, the g_mass_storage
legacy gadget driver attempts to unregister itself when its main
operating thread terminates (if it hasn't been unregistered already).
This is not strictly necessary; it was never more than an attempt to
have the gadget fail cleanly if something went wrong and the main
thread was killed.
However, now that the UDC core manages gadget drivers independently of
UDC drivers, this scheme doesn't work any more. A simple test:
modprobe dummy-hcd
modprobe g-mass-storage file=...
rmmod dummy-hcd
ends up in a deadlock with the following backtrace:
sysrq: SysRq : Show Blocked State
task PC stack pid father
file-storage D 0 1130 2 0x00000000
Call Trace:
__schedule+0x53e/0x58c
schedule+0x6e/0x77
schedule_preempt_disabled+0xd/0xf
__mutex_lock.isra.1+0x129/0x224
? _raw_spin_unlock_irqrestore+0x12/0x14
__mutex_lock_slowpath+0x12/0x14
mutex_lock+0x28/0x2b
usb_gadget_unregister_driver+0x29/0x9b [udc_core]
usb_composite_unregister+0x10/0x12 [libcomposite]
msg_cleanup+0x1d/0x20 [g_mass_storage]
msg_thread_exits+0xd/0xdd7 [g_mass_storage]
fsg_main_thread+0x1395/0x13d6 [usb_f_mass_storage]
? __schedule+0x573/0x58c
kthread+0xd9/0xdb
? do_set_interface+0x25c/0x25c [usb_f_mass_storage]
? init_completion+0x1e/0x1e
ret_from_fork+0x19/0x24
rmmod D 0 1155 683 0x00000000
Call Trace:
__schedule+0x53e/0x58c
schedule+0x6e/0x77
schedule_timeout+0x26/0xbc
? __schedule+0x573/0x58c
do_wait_for_common+0xb3/0x128
? usleep_range+0x81/0x81
? wake_up_q+0x3f/0x3f
wait_for_common+0x2e/0x45
wait_for_completion+0x17/0x19
fsg_common_put+0x34/0x81 [usb_f_mass_storage]
fsg_free_inst+0x13/0x1e [usb_f_mass_storage]
usb_put_function_instance+0x1a/0x25 [libcomposite]
msg_unbind+0x2a/0x42 [g_mass_storage]
__composite_unbind+0x4a/0x6f [libcomposite]
composite_unbind+0x12/0x14 [libcomposite]
usb_gadget_remove_driver+0x4f/0x77 [udc_core]
usb_del_gadget_udc+0x52/0xcc [udc_core]
dummy_udc_remove+0x27/0x2c [dummy_hcd]
platform_drv_remove+0x1d/0x31
device_release_driver_internal+0xe9/0x16d
device_release_driver+0x11/0x13
bus_remove_device+0xd2/0xe2
device_del+0x19f/0x221
? selinux_capable+0x22/0x27
platform_device_del+0x21/0x63
platform_device_unregister+0x10/0x1a
cleanup+0x20/0x817 [dummy_hcd]
SyS_delete_module+0x10c/0x197
? ____fput+0xd/0xf
? task_work_run+0x55/0x62
? prepare_exit_to_usermode+0x65/0x75
do_fast_syscall_32+0x86/0xc3
entry_SYSENTER_32+0x4e/0x7c
What happens is that removing the dummy-hcd driver causes the UDC core
to unbind the gadget driver, which it does while holding the udc_lock
mutex. The unbind routine in g_mass_storage tells the main thread to
exit and waits for it to terminate.
But as mentioned above, when the main thread exits it tries to
unregister the mass-storage function driver. Via the composite
framework this ends up calling usb_gadget_unregister_driver(), which
tries to acquire the udc_lock mutex. The result is deadlock.
The simplest way to fix the problem is not to be so clever: The main
thread doesn't have to unregister the function driver. The side
effects won't be so terrible; if the gadget is still attached to a USB
host when the main thread is killed, it will appear to the host as
though the gadget's firmware has crashed -- a reasonably accurate
interpretation, and an all-too-common occurrence for USB mass-storage
devices.
In fact, the code to unregister the driver when the main thread exits
is specific to g-mass-storage; it is not used when f-mass-storage is
included as a function in a larger composite device. Therefore the
entire mechanism responsible for this (the fsg_operations structure
with its ->thread_exits method, the fsg_common_set_ops() routine, and
the msg_thread_exits() callback routine) can all be eliminated. Even
the msg_registered bitflag can be removed, because now the driver is
unregistered in only one place rather than in two places.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The gadgetfs driver (drivers/usb/gadget/legacy/inode.c) was written
before the UDC and composite frameworks were adopted; it is a legacy
driver. As such, it expects that once bound to a UDC controller, it
will not be unbound until it unregisters itself.
However, the UDC framework does unbind function drivers while they are
still registered. When this happens, it can cause the gadgetfs driver
to misbehave or crash. For example, userspace can cause a crash by
opening the device file and doing an ioctl call before setting up a
configuration (found by Andrey Konovalov using the syzkaller fuzzer).
This patch adds checks and synchronization to prevent these bad
behaviors. It adds a udc_usage counter that the driver increments at
times when it is using a gadget interface without holding the private
spinlock. The unbind routine waits for this counter to go to 0 before
returning, thereby ensuring that the UDC is no longer in use.
The patch also adds a check in the dev_ioctl() routine to make sure
the driver is bound to a UDC before dereferencing the gadget pointer,
and it makes destroy_ep_files() synchronize with the endpoint I/O
routines, to prevent the user from accessing an endpoint data
structure after it has been removed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
CC: <stable@vger.kernel.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The gadgetfs driver as a long-outstanding FIXME, regarding a call of
copy_to_user() made while holding a spinlock. This patch fixes the
issue by dropping the spinlock and using the dev->udc_usage mechanism
introduced by another recent patch to guard against status changes
while the lock isn't held.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
CC: <stable@vger.kernel.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The uas driver has a subtle bug in the way it handles alternate
settings. The uas_find_uas_alt_setting() routine returns an
altsetting value (the bAlternateSetting number in the descriptor), but
uas_use_uas_driver() then treats that value as an index to the
intf->altsetting array, which it isn't.
Normally this doesn't cause any problems because the various
alternate settings have bAlternateSetting values 0, 1, 2, ..., so the
value is equal to the index in the array. But this is not guaranteed,
and Andrey Konovalov used the syzkaller fuzzer with KASAN to get a
slab-out-of-bounds error by violating this assumption.
This patch fixes the bug by making uas_find_uas_alt_setting() return a
pointer to the altsetting entry rather than either the value or the
index. Pointers are less subject to misinterpretation.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
CC: Oliver Neukum <oneukum@suse.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kris Lindgren reports that without the NO_WP_DETECT flag, his Seagate
external disk drive fails all write accesses. This regresssion dates
back approximately to the start of the 4.x kernel releases.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Kris Lindgren <kris.lindgren@gmail.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ever since commit a621bac304 ("scsi_lib: correctly retry failed zero
length REQ_TYPE_FS commands"), people have been getting bogus error
messages for USB disk drives using ATA pass-thru. For example:
[ 1344.880193] sd 6:0:0:0: [sdb] Attached SCSI disk
[ 1345.069152] sd 6:0:0:0: [sdb] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_SENSE
[ 1345.069159] sd 6:0:0:0: [sdb] tag#0 Sense Key : Hardware Error [current] [descriptor]
[ 1345.069162] sd 6:0:0:0: [sdb] tag#0 Add. Sense: No additional sense information
[ 1345.069168] sd 6:0:0:0: [sdb] tag#0 CDB: ATA command pass through(16) 85 06 20 00 00 00 00 00 00 00 00 00 00 00 e5 00
[ 1345.172252] sd 6:0:0:0: [sdb] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_SENSE
[ 1345.172258] sd 6:0:0:0: [sdb] tag#0 Sense Key : Hardware Error [current] [descriptor]
[ 1345.172261] sd 6:0:0:0: [sdb] tag#0 Add. Sense: No additional sense information
[ 1345.172266] sd 6:0:0:0: [sdb] tag#0 CDB: ATA command pass through(12)/Blank a1 06 20 da 00 00 4f c2 00 b0 00 00
These messages can be quite annoying, because programs like udisks2
provoke them every 10 minutes or so. Other programs can also have
this effect, such as those in smartmontools.
I don't fully understand how that commit induced the SCSI core to log
these error messages, but the underlying cause for them is code added
to usb-storage by commit f1a0743bc0 ("USB: storage: When a device
returns no sense data, call it a Hardware Error"). At the time it was
necessary to do this, in order to prevent an infinite retry loop with
some not-so-great mass storage devices.
However, the ATA pass-thru protocol uses SCSI sense data to return
command status values, and some devices always report Check Condition
status for ATA pass-thru commands to ensure that the host retrieves
the sense data, even if the command succeeded. This violates the USB
mass-storage protocol (Check Condition status is supposed to mean the
command failed), but we can't help that.
This patch attempts to mitigate the problem of these bogus error
reports by changing usb-storage. The HARDWARE ERROR sense key will be
inserted only for commands that aren't ATA pass-thru.
Thanks to Ewan Milne for pointing out that this mechanism was present
in usb-storage. 8 years after writing it, I had completely forgotten
its existence.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Kris Lindgren <kris.lindgren@gmail.com>
Ref: https://bugzilla.redhat.com/show_bug.cgi?id=1351305
CC: Ewan D. Milne <emilne@redhat.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrey Konovalov reported a possible out-of-bounds problem for the
cdc_parse_cdc_header function. He writes:
It looks like cdc_parse_cdc_header() doesn't validate buflen
before accessing buffer[1], buffer[2] and so on. The only check
present is while (buflen > 0).
So fix this issue up by properly validating the buffer length matches
what the descriptor says it is.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
First set of fixes for the gadget side. Not much this time around,
things have been rather calm.
In no order whatsoever, this pull request contains:
- A DMA starvation fix on dwc3 caused by some recent changes to how we
map/unmap requests
- A build error fix on the snps_udc_plat.c driver
- A fix for how to we call ->udc_set_speed()
- Spinlock recursion fix on the printer gadget
- Removal of pointless comparisons on dummy driver
-----BEGIN PGP SIGNATURE-----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=5OKH
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.14-rc2
First set of fixes for the gadget side. Not much this time around,
things have been rather calm.
In no order whatsoever, this pull request contains:
- A DMA starvation fix on dwc3 caused by some recent changes to how we
map/unmap requests
- A build error fix on the snps_udc_plat.c driver
- A fix for how to we call ->udc_set_speed()
- Spinlock recursion fix on the printer gadget
- Removal of pointless comparisons on dummy driver
In case the usb phy has the capability to detect usb charger type,
do it when vbus is on.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
gcc-8 points out two comparisons that are clearly bogus
and almost certainly not what the author intended to write:
drivers/usb/gadget/udc/dummy_hcd.c: In function 'set_link_state_by_speed':
drivers/usb/gadget/udc/dummy_hcd.c:379:31: error: bitwise comparison always evaluates to false [-Werror=tautological-compare]
USB_PORT_STAT_ENABLE) == 1 &&
^~
drivers/usb/gadget/udc/dummy_hcd.c:381:25: error: bitwise comparison always evaluates to false [-Werror=tautological-compare]
USB_SS_PORT_LS_U0) == 1 &&
^~
I looked at the code for a bit and came up with a change that makes
it look like what the author probably meant here. This makes it
look reasonable to me and to gcc, shutting up the warning.
It does of course change behavior as the two conditions are actually
evaluated rather than being hardcoded to false, and I have made no
attempt at verifying that the changed logic makes sense in the context
of a USB HCD, so that part needs to be reviewed carefully.
Fixes: 1cd8fd2887 ("usb: gadget: dummy_hcd: add SuperSpeed support")
Cc: Tatyana Brokhman <tlinder@codeaurora.org>
Cc: Felipe Balbi <balbi@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix build errors that happen when CONFIG_EXTCON=m and
CONFIG_USB_SNP_UDC_PLAT=y by preventing that combination in Kconfig.
CONFIG_EXTCON can still be disabled or enabled for this driver since
<linux/extcon.h> has stubs for the disabled case, but if CONFIG_EXTCON=m,
USB_SNP_UDC_PLAT is restricted to m or n (cannot be builtin).
drivers/built-in.o: In function `udc_plat_remove':
snps_udc_plat.c:(.text+0x2c4060): undefined reference to `extcon_unregister_notifier'
drivers/built-in.o: In function `udc_plat_probe':
snps_udc_plat.c:(.text+0x2c438c): undefined reference to `extcon_get_edev_by_phandle'
snps_udc_plat.c:(.text+0x2c43f2): undefined reference to `extcon_register_notifier'
snps_udc_plat.c:(.text+0x2c4416): undefined reference to `extcon_get_state'
snps_udc_plat.c:(.text+0x2c44f7): undefined reference to `extcon_unregister_notifier'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If usb_gadget_giveback_request() is called in usb_ep_queue(),
this printer_write() is possible to cause spinlock recursion. So,
this patch adds spin_unlock() before calls usb_ep_queue() to avoid it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Consider the following case: udc controller supports SuperSpeed. If we
first load a HighSpeed gadget followed by a SuperSpeed gadget, the
SuperSpeed gadget will be limited to HighSpeed as UDC core driver
doesn't call ->udc_set_speed() in the second case.
Call ->udc_set_speed() unconditionally to fix this issue.
This will also fix the case for dwc3 controller driver when SuperSpeed
gadget is loaded first and works in HighSpeed only as udc_set_speed()
was never being called.
Fixes: 6099eca796ae ("usb: gadget: core: introduce ->udc_set_speed() method")
Cc: <stable@vger.kernel.org> [v4.13+]
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Andrey Konovalov reported a possible out-of-bounds problem for a USB interface
association descriptor. He writes:
It seems there's no proper size check of a USB_DT_INTERFACE_ASSOCIATION
descriptor. It's only checked that the size is >= 2 in
usb_parse_configuration(), so find_iad() might do out-of-bounds access
to intf_assoc->bInterfaceCount.
And he's right, we don't check for crazy descriptors of this type very well, so
resolve this problem. Yet another issue found by syzkaller...
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the USB device id for the ELV TFD500 data logger.
Signed-off-by: Andreas Engel <anen-nospam@gmx.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
When adding GPIO support for the cp2105, the mentioned commit by Martyn
Welch introduced a query for the part number of the chip. Unfortunately
the driver aborts probing when this query fails, so currently the driver
can not be used with chips not supporting this query.
I have a data cable for Siemens mobile phones (ID 10ab:10c5) where this
is the case.
With this patch the driver can be bound even if the part number can not
be queried.
Fixes: cf5276ce78 ("USB: serial: cp210x: Adding GPIO support for CP2105")
Signed-off-by: Sebastian Frei <dr.nop@gmx.net>
[ johan: amend commit message; shorten error message and demote to
warning; drop unnecessary move of usb_set_serial_data() ]
Cc: stable <stable@vger.kernel.org> # 4.9
Signed-off-by: Johan Hovold <johan@kernel.org>
This reverts commit dec08194ff.
Commit dec08194ff ("xhci: Limit USB2 port wake support for AMD Promontory
hosts") makes all high speed USB ports on ASUS PRIME B350M-A cease to
function after enabling runtime PM.
All boards with this chipsets will be affected, so revert the commit.
The original patch was added to stable 4.9, 4.11 and 4.12 and needs
to reverted from there as well
Cc: <stable@vger.kernel.org> # 4.9+
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A SuperSpeedPlus roothub needs to have the Link Protocol (LP) bit set in
the bmSublinkSpeedAttr[] entry of a SuperSpeedPlus descriptor.
If the xhci controller has an optional Protocol Speed ID (PSI) table then
that will be used as a base to create the roothub SuperSpeedPlus
descriptor.
The PSI table does not however necessary contain the LP bit so we need
to set it manually.
Check the psi speed and set LP bit if speed is 10Gbps or higher.
We're not setting it for 5 to 10Gbps as USB 3.1 specification always
mention SuperSpeedPlus for 10Gbps or higher, and some SSIC USB 3.0 speeds
can be over 5Gbps, such as SSIC-G3B-L1 at 5830 Mbps
Cc: <stable@vger.kernel.org> # 4.6+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The flow control workaround for ASM1042A xHC hosts sleeps between
register polling. The workaround gets called in several places, among
them with spin_lock_irq() held when xHC host is resumed or hoplug removed.
This was noticed as kernel panics at resume on a Dell XPS15 9550 with
TB16 thunderbolt dock.
Avoid sleeping with spin_lock_irq() held, use udelay() instead
The original workaround was added to 4.9 and 4.12 stable releases,
this patch needs to be applied to those as well.
Fixes: 9da5a1092b ("xhci: Bad Ethernet performance plugged in ASM1042A host")
Cc: <stable@vger.kernel.org> #4.9+
Reported-by: Jose Marino <marinoj@nso.edu>
Tested-by: Jose Marino <marinoj@nso.edu>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 4c39d4b949 ("usb: xhci: use bus->sysdev for DMA configuration")
updated the method determining DMA for XHCI from sysdev. However, this
patch broke the ability to enumerate the FWNODE from parent ACPI devices
from the child plat XHCI device.
Currently, xhci_plat is not set up properly when the parent device is an
ACPI node. The conditions that xhci_plat_probe should satisfy are
1. xhci_plat comes from firmware
2. xhci_plat is child of a device from firmware (dwc3-plat)
3. xhci_plat is grandchild of a pci device (dwc3-pci)
Case 2 is covered when the child is an OF node (by checking
sysdev->parent->of_node), however, an ACPI parent will return NULL in
the of_node check and will thus not result in sysdev being set to
sysdev->parent
[ 17.591549] xhci-hcd: probe of xhci-hcd.6.auto failed with error -5
This change adds a check for ACPI to completely allow for condition 2.
This is done by first checking if the parent node is of type ACPI (e.g.,
dwc3-plat) and set sysdev to sysdev->parent if either of the two
following conditions are met:
1: If fwnode is empty (in the case that platform_device_add_properties
was not called on the allocated platform device)
2: fwnode exists but is not of type ACPI (this would happen if
platform_device_add_properties was called on the allocated device.
Instead of type FWNODE_ACPI, you would end up with FWNODE_PDATA)
Cc: stable@vger.kernel.org #4.12.x
Cc: stable@vger.kernel.org #4.13.x
Fixes: 4c39d4b949 ("usb: xhci: use bus->sysdev for DMA configuration")
Tested-by: Thang Q. Nguyen <tqnguyen@apm.com>
Signed-off-by: Adam Wallis <awallis@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Read the endpiont ESIT from endpiont context using correct macro.
Add a macro for reading the high bits of ESIT for Large ESIT Payload
Capable hosts (LEC=1)
Cc: <stable@vger.kernel.org> # 4.12
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Servers were emitting failed handoff messages but were not
waiting the full 1 second as designated in section 4.22.1 of
the eXtensible Host Controller Interface specifications. The
handshake was using wrong units so calls were made with milliseconds
not microseconds. Comments referenced 5 seconds not 1 second as
in specs.
The wrong units were also corrected in a second handshake call.
Cc: <stable@vger.kernel.org>
Signed-off-by: Jim Dickerson <jim.dickerson@hpe.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci driver keeps a bus_state structure for each hcd (usb2 and usb3)
The structure is picked based on hcd speed, but driver only compared
for HCD_USB3 speed, returning the wrong bus_state for HCD_USB31 hosts.
This caused null pointer dereference errors in bus_resume function.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the xhci_add_endpoint(), a new ring was allocated and saved at
xhci_virt_ep->new_ring. Hence, when error happens, we need to free
the allocated ring before returning error.
Current code frees xhci_virt_ep->ring instead of the new_ring. This
patch fixes this.
Cc: <stable@vger.kernel.org>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't populate const arrays on the stack, instead make them
static. Makes the object code smaller by over 1070 bytes:
Before:
text data bss dec hex filename
3505 880 0 4385 1121 drivers/usb/storage/option_ms.o
After:
text data bss dec hex filename
2269 1040 0 3309 ced drivers/usb/storage/option_ms.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we don't assign a TRB to ep0 requests, we won't be able to unmap
the request later on resulting in starvation of DMA resources.
Fixes: 4a71fcb8ac ("usb: dwc3: gadget: only unmap requests from DMA if mapped")
Reported-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Make code more concise and readable
Signed-off-by: Harsha Sharma <harshasharmaiitr@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e0429362ab
("usb: Add device quirk for Logitech HD Pro Webcams C920 and C930e")
introduced quirk to workaround an issue with some Logitech webcams.
The workaround is introducing delay for some USB operations.
According to our testing, delay introduced by original commit
is not long enough and in rare cases we still see issues described
by the aforementioned commit.
This patch increases delays introduced by original commit.
Having this patch applied we do not see those problems anymore.
Signed-off-by: Dmitry Fleytman <dmitry@daynix.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver is in good enough shape to be moved out of staging.
Do it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds support for TP-Link LTE mPCIe module is used
in in TP-Link MR200v1, MR6400v1 and v2 routers.
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add CYPRESS_VID vid and CYPRESS_WICED_BT_USB and CYPRESS_WICED_WL_USB
device IDs to ftdi_sio driver.
Signed-off-by: Jeffrey Chu <jeffrey.chu@cypress.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Pull more set_fs removal from Al Viro:
"Christoph's 'use kernel_read and friends rather than open-coding
set_fs()' series"
* 'work.set_fs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: unexport vfs_readv and vfs_writev
fs: unexport vfs_read and vfs_write
fs: unexport __vfs_read/__vfs_write
lustre: switch to kernel_write
gadget/f_mass_storage: stop messing with the address limit
mconsole: switch to kernel_read
btrfs: switch write_buf to kernel_write
net/9p: switch p9_fd_read to kernel_write
mm/nommu: switch do_mmap_private to kernel_read
serial2002: switch serial2002_tty_write to kernel_{read/write}
fs: make the buf argument to __kernel_write a void pointer
fs: fix kernel_write prototype
fs: fix kernel_read prototype
fs: move kernel_read to fs/read_write.c
fs: move kernel_write to fs/read_write.c
autofs4: switch autofs4_write to __kernel_write
ashmem: switch to ->read_iter
- removal of the old dma_alloc_noncoherent interface
- remove unused flags to dma_declare_coherent_memory
- restrict OF DMA configuration to specific physical busses
- use the iommu mailing list for dma-mapping questions and
patches
-----BEGIN PGP SIGNATURE-----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=qHNs
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.14' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- removal of the old dma_alloc_noncoherent interface
- remove unused flags to dma_declare_coherent_memory
- restrict OF DMA configuration to specific physical busses
- use the iommu mailing list for dma-mapping questions and patches
* tag 'dma-mapping-4.14' of git://git.infradead.org/users/hch/dma-mapping:
dma-coherent: fix dma_declare_coherent_memory() logic error
ARM: imx: mx31moboard: Remove unused 'dma' variable
dma-coherent: remove an unused variable
MAINTAINERS: use the iommu list for the dma-mapping subsystem
dma-coherent: remove the DMA_MEMORY_MAP and DMA_MEMORY_IO flags
dma-coherent: remove the DMA_MEMORY_INCLUDES_CHILDREN flag
of: restrict DMA configuration
dma-mapping: remove dma_alloc_noncoherent and dma_free_noncoherent
i825xx: switch to switch to dma_alloc_attrs
au1000_eth: switch to dma_alloc_attrs
sgiseeq: switch to dma_alloc_attrs
dma-mapping: reduce dma_mapping_error inline bloat
This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas, megaraid_sas, zfcp and a host of minor updates.
The major driver change here is the elimination of the block based
cciss driver in favour of the SCSI based hpsa driver (which now drives
all the legacy cases cciss used to be required for). Plus a reset
handler clean up and the redo of the SAS SMP handler to use bsg lib.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=nQUG
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas,
megaraid_sas, zfcp and a host of minor updates.
The major driver change here is the elimination of the block based
cciss driver in favour of the SCSI based hpsa driver (which now drives
all the legacy cases cciss used to be required for). Plus a reset
handler clean up and the redo of the SAS SMP handler to use bsg lib"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (279 commits)
scsi: scsi-mq: Always unprepare before requeuing a request
scsi: Show .retries and .jiffies_at_alloc in debugfs
scsi: Improve requeuing behavior
scsi: Call scsi_initialize_rq() for filesystem requests
scsi: qla2xxx: Reset the logo flag, after target re-login.
scsi: qla2xxx: Fix slow mem alloc behind lock
scsi: qla2xxx: Clear fc4f_nvme flag
scsi: qla2xxx: add missing includes for qla_isr
scsi: qla2xxx: Fix an integer overflow in sysfs code
scsi: aacraid: report -ENOMEM to upper layer from aac_convert_sgraw2()
scsi: aacraid: get rid of one level of indentation
scsi: aacraid: fix indentation errors
scsi: storvsc: fix memory leak on ring buffer busy
scsi: scsi_transport_sas: switch to bsg-lib for SMP passthrough
scsi: smartpqi: remove the smp_handler stub
scsi: hpsa: remove the smp_handler stub
scsi: bsg-lib: pass the release callback through bsg_setup_queue
scsi: Rework handling of scsi_device.vpd_pg8[03]
scsi: Rework the code for caching Vital Product Data (VPD)
scsi: rcu: Introduce rcu_swap_protected()
...
- RK805 Power Management IC (PMIC)
- ROHM BD9571MWV-M MFD Power Management IC (PMIC)
- Texas Instruments TPS68470 Power Management IC (PMIC) & LEDs
- New Device Support
- Add support for HiSilicon Hi6421v530 to hi6421-pmic-core
- Add support for X-Powers AXP806 to axp20x
- Add support for X-Powers AXP813 to axp20x
- Add support for Intel Sunrise Point LPSS to intel-lpss-pci
- New Functionality
- Amend API to provide register layout; atmel-smc
- Fix-ups
- DT re-work; omap, nokia
- Header file location change {I2C => MFD}; dm355evm_msp, tps65010
- Fix chip ID formatting issue(s); rk808
- Optionally register touchscreen devices; da9052-core
- Documentation improvements; twl-core
- Constification; rtsx_pcr, ab8500-core, da9055-i2c, da9052-spi
- Drop unnecessary static declaration; max8925-i2c
- Kconfig changes (missing deps and remove module support)
- Slim down oversized licence statement; hi6421-pmic-core
- Use managed resources (devm_*); lp87565
- Supply proper error checking/handling; t7l66xb
- Bug Fixes
- Fix counter duplication issue; da9052-core
- Fix potential NULL deference issue; max8998
- Leave SPI-NOR write-protection bit alone; lpc_ich
- Ensure device is put into reset during suspend; intel-lpss
- Correct register offset variable size; omap-usb-tll
-----BEGIN PGP SIGNATURE-----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=TKIm
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers
- RK805 Power Management IC (PMIC)
- ROHM BD9571MWV-M MFD Power Management IC (PMIC)
- Texas Instruments TPS68470 Power Management IC (PMIC) & LEDs
New Device Support:
- Add support for HiSilicon Hi6421v530 to hi6421-pmic-core
- Add support for X-Powers AXP806 to axp20x
- Add support for X-Powers AXP813 to axp20x
- Add support for Intel Sunrise Point LPSS to intel-lpss-pci
New Functionality:
- Amend API to provide register layout; atmel-smc
Fix-ups:
- DT re-work; omap, nokia
- Header file location change {I2C => MFD}; dm355evm_msp, tps65010
- Fix chip ID formatting issue(s); rk808
- Optionally register touchscreen devices; da9052-core
- Documentation improvements; twl-core
- Constification; rtsx_pcr, ab8500-core, da9055-i2c, da9052-spi
- Drop unnecessary static declaration; max8925-i2c
- Kconfig changes (missing deps and remove module support)
- Slim down oversized licence statement; hi6421-pmic-core
- Use managed resources (devm_*); lp87565
- Supply proper error checking/handling; t7l66xb
Bug Fixes:
- Fix counter duplication issue; da9052-core
- Fix potential NULL deference issue; max8998
- Leave SPI-NOR write-protection bit alone; lpc_ich
- Ensure device is put into reset during suspend; intel-lpss
- Correct register offset variable size; omap-usb-tll"
* tag 'mfd-next-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (61 commits)
mfd: intel_soc_pmic: Differentiate between Bay and Cherry Trail CRC variants
mfd: intel_soc_pmic: Export separate mfd-cell configs for BYT and CHT
dt-bindings: mfd: Add bindings for ZII RAVE devices
mfd: omap-usb-tll: Fix register offsets
mfd: da9052: Constify spi_device_id
mfd: intel-lpss: Put I2C and SPI controllers into reset state on suspend
mfd: da9055: Constify i2c_device_id
mfd: intel-lpss: Add missing PCI ID for Intel Sunrise Point LPSS devices
mfd: t7l66xb: Handle return value of clk_prepare_enable
mfd: Add ROHM BD9571MWV-M PMIC DT bindings
mfd: intel_soc_pmic_chtwc: Turn Kconfig option into a bool
mfd: lp87565: Convert to use devm_mfd_add_devices()
mfd: Add support for TPS68470 device
mfd: lpc_ich: Do not touch SPI-NOR write protection bit on Haswell/Broadwell
mfd: syscon: atmel-smc: Add helper to retrieve register layout
mfd: axp20x: Use correct platform device ID for many PEK
dt-bindings: mfd: axp20x: Introduce bindings for AXP813
mfd: axp20x: Add support for AXP813 PMIC
dt-bindings: mfd: axp20x: Add AXP806 to supported list of chips
mfd: Add ROHM BD9571MWV-M MFD PMIC driver
...
Here is the big char/misc driver update for 4.14-rc1.
Lots of different stuff in here, it's been an active development cycle
for some reason. Highlights are:
- updated binder driver, this brings binder up to date with what
shipped in the Android O release, plus some more changes that
happened since then that are in the Android development trees.
- coresight updates and fixes
- mux driver file renames to be a bit "nicer"
- intel_th driver updates
- normal set of hyper-v updates and changes
- small fpga subsystem and driver updates
- lots of const code changes all over the driver trees
- extcon driver updates
- fmc driver subsystem upadates
- w1 subsystem minor reworks and new features and drivers added
- spmi driver updates
Plus a smattering of other minor driver updates and fixes.
All of these have been in linux-next with no reported issues for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWa1+Ew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yl26wCgquufNylfhxr65NbJrovduJYzRnUAniCivXg8
bePIh/JI5WxWoHK+wEbY
=hYWx
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big char/misc driver update for 4.14-rc1.
Lots of different stuff in here, it's been an active development cycle
for some reason. Highlights are:
- updated binder driver, this brings binder up to date with what
shipped in the Android O release, plus some more changes that
happened since then that are in the Android development trees.
- coresight updates and fixes
- mux driver file renames to be a bit "nicer"
- intel_th driver updates
- normal set of hyper-v updates and changes
- small fpga subsystem and driver updates
- lots of const code changes all over the driver trees
- extcon driver updates
- fmc driver subsystem upadates
- w1 subsystem minor reworks and new features and drivers added
- spmi driver updates
Plus a smattering of other minor driver updates and fixes.
All of these have been in linux-next with no reported issues for a
while"
* tag 'char-misc-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (244 commits)
ANDROID: binder: don't queue async transactions to thread.
ANDROID: binder: don't enqueue death notifications to thread todo.
ANDROID: binder: Don't BUG_ON(!spin_is_locked()).
ANDROID: binder: Add BINDER_GET_NODE_DEBUG_INFO ioctl
ANDROID: binder: push new transactions to waiting threads.
ANDROID: binder: remove proc waitqueue
android: binder: Add page usage in binder stats
android: binder: fixup crash introduced by moving buffer hdr
drivers: w1: add hwmon temp support for w1_therm
drivers: w1: refactor w1_slave_show to make the temp reading functionality separate
drivers: w1: add hwmon support structures
eeprom: idt_89hpesx: Support both ACPI and OF probing
mcb: Fix an error handling path in 'chameleon_parse_cells()'
MCB: add support for SC31 to mcb-lpc
mux: make device_type const
char: virtio: constify attribute_group structures.
Documentation/ABI: document the nvmem sysfs files
lkdtm: fix spelling mistake: "incremeted" -> "incremented"
perf: cs-etm: Fix ETMv4 CONFIGR entry in perf.data file
nvmem: include linux/err.h from header
...
Instead use kernel_read/write consistently, which also makes sparse
happy.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Here are the USB-serial updates for 4.14-rc1; a new option device id and
one device-id clean up.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=FIU8
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.14-rc1
Here are the USB-serial updates for 4.14-rc1; a new option device id and
one device-id clean up.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
DMA_MEMORY_IO was never used in the tree, so remove it. That means there is
no need for the DMA_MEMORY_MAP flag either now, so remove it as well and
change dma_declare_coherent_memory to return a normal errno value.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Make this const as it is not modified anywhere.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make this const as it is not modified anywhere.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make this structure const as it is not modified. And replace __initdata
with __initconst to avoid section conflict error.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xhci-mtk driver is a generic driver for MediaTek xHCI IP, add
a generic compatible to avoid confusion when support new SoCs but
use a compatible with specific SoC's name "mt8173".
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds recovery from false busy state on concurrent attach
operation.
The procedure of attach operation is as below.
1) Find an unused port in /sys/devices/platform/vhci_hcd/status.
(userspace)
2) Request attach found port to driver through
/sys/devices/platform/vhci_hcd/attach. (userspace)
3) Lock table, reserve requested port and unlock table. (vhci driver)
Attaching more than one remote devices concurrently, same unused port
number will be found in step-1. Then one request will succeed and
others will fail even though there are some unused ports.
With this patch, driver returns EBUSY when requested port has already
been used. In this case, attach command retries from step-1: finding
another unused port. If there's no unused port, the attach operation
will fail in step-1. Otherwise it retries automatically using another
unused port.
vhci-hcd's interface (only errno) is changed as following.
Current errno New errno Condition
EINVAL same as left specified port number is in invalid
range
EAGAIN same as left platform_get_drvdata() failed
EINVAL same as left specified socket fd is not valid
EINVAL EBUSY specified port status is not free
The errno EBUSY was not used in userspace
src/usbip_attach.c:import_device(). It is needed to distinguish the
condition to be able to retry from other unrecoverable errors.
It is possible to avoid this failure by introducing userspace exclusive
control. But it's exaggerated for this special condition. The locking
itself has done in driver.
As an alternate solution, userspace doesn't specify port number, driver
searches unused port and it returns port number to the userspace. With
this solution, the interface is much different than this patch.
Signed-off-by: Nobuo Iwata <nobuo.iwata@fujixerox.co.jp>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Detailed description for this pull request:
1. Add new 'extcon-usbc-cros-ec.c' driver
- ChromeOS Embedded Controller extcon driver supports
the detection of the Display Port (EXTCON_DISP_DP)
through USB C-type and contol it.
2. Update extcon core
- Modify the description for both functions and structures
in order to improve the readability and give the more correct
guide about the role of functions because there are different
explanation even if the same arguments.
- Keep the indentation with tab instead of space
- Remove the following deprecated extcon API. The deprecated API
are exchanged on all of linux tree.
: extcon_get_cable_state_() -> extcon_get_state()
: extcon_set_cable_state_() -> extcon_set_state_sync()
3. Include the two immutable branch as following:
- ib-extcon-mfd-4.14 for the 'extcon-ubsc-cros-ec.c' driver
because the patches of 'extcon-ubsc-cros-ec.c' touch the MFD directory.
- ib-extcon-usb-phy-4.14 for removing the deprecated extcon API
because the usb/phy driver usese the deprecated extcon API.
So, this immutable branch alters the extcon API and then
remove them from extcon.
4. Fix minor issue of extcon driver
- Fix the MHL detection on extcon-max77693.c
- Convert to using %pOF instead of full_name on extcon.c
- Add 'const' kerywod for acpi_device_id on extcon-intel-int3496.c
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=oQMu
-----END PGP SIGNATURE-----
Merge tag 'extcon-next-for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into char-misc-next
Chanwoo writes:
Update extcon for 4.14
Detailed description for this pull request:
1. Add new 'extcon-usbc-cros-ec.c' driver
- ChromeOS Embedded Controller extcon driver supports
the detection of the Display Port (EXTCON_DISP_DP)
through USB C-type and contol it.
2. Update extcon core
- Modify the description for both functions and structures
in order to improve the readability and give the more correct
guide about the role of functions because there are different
explanation even if the same arguments.
- Keep the indentation with tab instead of space
- Remove the following deprecated extcon API. The deprecated API
are exchanged on all of linux tree.
: extcon_get_cable_state_() -> extcon_get_state()
: extcon_set_cable_state_() -> extcon_set_state_sync()
3. Include the two immutable branch as following:
- ib-extcon-mfd-4.14 for the 'extcon-ubsc-cros-ec.c' driver
because the patches of 'extcon-ubsc-cros-ec.c' touch the MFD directory.
- ib-extcon-usb-phy-4.14 for removing the deprecated extcon API
because the usb/phy driver usese the deprecated extcon API.
So, this immutable branch alters the extcon API and then
remove them from extcon.
4. Fix minor issue of extcon driver
- Fix the MHL detection on extcon-max77693.c
- Convert to using %pOF instead of full_name on extcon.c
- Add 'const' kerywod for acpi_device_id on extcon-intel-int3496.c
Check memory allocation failure and return -ENOMEM in such a case, as
already done few lines below for another memory allocation.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e0429362ab
("usb: Add device quirk for Logitech HD Pro Webcams C920 and C930e")
introduced quirk to workaround an issue with some Logitech webcams.
Apparently model C920-C has the same issue so applying
the same quirk as well.
See aforementioned commit message for detailed explanation of the problem.
Signed-off-by: Dmitry Fleytman <dmitry@daynix.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for the SuperSpeed Link Layer test case TD.7.34
which requires the operator to place the port into compliance
mode, and to subsequently bring it out via reset. Historically
according to the (now deprecated) USB 3.0 specification a
SuperSpeed host downstream port would automatically transition
to Compliance mode from the Polling state if LFPS polling times
out. However the language in USB 3.1 as well as xHCI 1.1 states
it may be required to explicitly enable this transition. For
such hosts this is done by sending a SET_FEATURE(PORT_LINK_STATE)
with the state set to Compliance to the root hub port.
Similar to the other supported commands, to do this via sysfs:
echo > /sys/bus/usb/devices/2-0\:1.0/enable_compliance
According to xHCI 1.1 section 4.19.1.2.4.1, this enables the
transition to compliance mode upon LFPS timeout. Note that this
can only be issued when the port is in disconnected state. And
in order to disable this behavior on subsequent transitions, a
warm reset should be issued. So add another entry to do that:
echo > /sys/bus/usb/devices/2-0\:1.0/warm_reset
In general these attributes can also be useful for other USB
SuperSpeed compliance tests such as electrical and eye diagram
testing which require CPn patterns to be transmitted.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To perform SuperSpeed compliance testing the port should first
be placed into compliance mode. For xHCI 1.0 and prior this
transition happens automatically when the port is in Training
and encounters an LFPS timeout. Thus running compliance tests
against a test appliance may simply just work by simply plugging
in to the downstream port.
However starting with xHCI 1.1 the transition from Polling.LFPS
to compliance mode may be disabled by default and needs to be
explicitly enabled by writing to the PLS field of the PORTSC
register, which sets an internal 'CTE' (Compliance Transition
Enabled) flag so that the port will perform the transition the
next time it encounters LFPS timeout. Whether this is disabled or
not is determined by the 'CTC' (Compliance Transition Capability)
bit in the HCCPARAMS2 capability register.
In order to allow a test operator to change this if needed, allow
a test driver (such as drivers/usb/misc/lvstest.c) to send a
SET_FEATURE(PORT_LINK_STATE) control message to the root hub to
update the link state prior to connecting to the port. Subsequently,
placing the port in warm reset would then disable the flag.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following commit cause a regression on ATI chipsets.
'commit e788787ef4 ("usb:xhci:Add quirk for Certain
failing HP keyboard on reset after resume")'
This causes pinfo->smbus_dev to be wrongly set to NULL on
systems with the ATI chipset that this function checks for first.
Added conditional check for AMD chipsets to avoid the overwriting
pinfo->smbus_dev.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: e788787ef4 ("usb:xhci:Add quirk for Certain
failing HP keyboard on reset after resume")
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
cc: <stable@vger.kernel.org>
Signed-off-by: Sandeep Singh <Sandeep.Singh@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Corsair Strafe RGB keyboard has trouble to initialize:
[ 1.679455] usb 3-6: new full-speed USB device number 4 using xhci_hcd
[ 6.871136] usb 3-6: unable to read config index 0 descriptor/all
[ 6.871138] usb 3-6: can't read configurations, error -110
[ 6.991019] usb 3-6: new full-speed USB device number 5 using xhci_hcd
[ 12.246642] usb 3-6: unable to read config index 0 descriptor/all
[ 12.246644] usb 3-6: can't read configurations, error -110
[ 12.366555] usb 3-6: new full-speed USB device number 6 using xhci_hcd
[ 17.622145] usb 3-6: unable to read config index 0 descriptor/all
[ 17.622147] usb 3-6: can't read configurations, error -110
[ 17.742093] usb 3-6: new full-speed USB device number 7 using xhci_hcd
[ 22.997715] usb 3-6: unable to read config index 0 descriptor/all
[ 22.997716] usb 3-6: can't read configurations, error -110
Although it may work after several times unpluging/pluging:
[ 68.195240] usb 3-6: new full-speed USB device number 11 using xhci_hcd
[ 68.337459] usb 3-6: New USB device found, idVendor=1b1c, idProduct=1b20
[ 68.337463] usb 3-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 68.337466] usb 3-6: Product: Corsair STRAFE RGB Gaming Keyboard
[ 68.337468] usb 3-6: Manufacturer: Corsair
[ 68.337470] usb 3-6: SerialNumber: 0F013021AEB8046755A93ED3F5001941
Tried three quirks: USB_QUIRK_DELAY_INIT, USB_QUIRK_NO_LPM and
USB_QUIRK_DEVICE_QUALIFIER, user confirmed that USB_QUIRK_DELAY_INIT alone
can workaround this issue. Hence add the quirk for Corsair Strafe RGB.
BugLink: https://bugs.launchpad.net/bugs/1678477
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make this const as it is only used during a copy operation.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use more compact of_property_read_bool() calls for the boolean properties
instead of of_find_property() calls in of_usb_host_tpl_support() and
of_usb_update_otg_caps().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vm_operations_struct are not supposed to change at runtime.
All functions working with const vm_operations_struct.
So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor code in order to avoid identical code for different branches.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While running reboot tests w/ a specific set of USB devices (and
slub_debug enabled), I found that once every few hours my device would
be crashed with a stack that looked like this:
[ 14.012445] BUG: spinlock bad magic on CPU#0, modprobe/2091
[ 14.012460] lock: 0xffffffc0cb055978, .magic: ffffffc0, .owner: cryption contexts: %lu/%lu
[ 14.012460] /1025536097, .owner_cpu: 0
[ 14.012466] CPU: 0 PID: 2091 Comm: modprobe Not tainted 4.4.79 #352
[ 14.012468] Hardware name: Google Kevin (DT)
[ 14.012471] Call trace:
[ 14.012483] [<....>] dump_backtrace+0x0/0x160
[ 14.012487] [<....>] show_stack+0x20/0x28
[ 14.012494] [<....>] dump_stack+0xb4/0xf0
[ 14.012500] [<....>] spin_dump+0x8c/0x98
[ 14.012504] [<....>] spin_bug+0x30/0x3c
[ 14.012508] [<....>] do_raw_spin_lock+0x40/0x164
[ 14.012515] [<....>] _raw_spin_lock_irqsave+0x64/0x74
[ 14.012521] [<....>] __wake_up+0x2c/0x60
[ 14.012528] [<....>] async_completed+0x2d0/0x300
[ 14.012534] [<....>] __usb_hcd_giveback_urb+0xc4/0x138
[ 14.012538] [<....>] usb_hcd_giveback_urb+0x54/0xf0
[ 14.012544] [<....>] xhci_irq+0x1314/0x1348
[ 14.012548] [<....>] usb_hcd_irq+0x40/0x50
[ 14.012553] [<....>] handle_irq_event_percpu+0x1b4/0x3f0
[ 14.012556] [<....>] handle_irq_event+0x4c/0x7c
[ 14.012561] [<....>] handle_fasteoi_irq+0x158/0x1c8
[ 14.012564] [<....>] generic_handle_irq+0x30/0x44
[ 14.012568] [<....>] __handle_domain_irq+0x90/0xbc
[ 14.012572] [<....>] gic_handle_irq+0xcc/0x18c
Investigation using kgdb() found that the wait queue that was passed
into wake_up() had been freed (it was filled with slub_debug poison).
I analyzed and instrumented the code and reproduced. My current
belief is that this is happening:
1. async_completed() is called (from IRQ). Moves "as" onto the
completed list.
2. On another CPU, proc_reapurbnonblock_compat() calls
async_getcompleted(). Blocks on spinlock.
3. async_completed() releases the lock; keeps running; gets blocked
midway through wake_up().
4. proc_reapurbnonblock_compat() => async_getcompleted() gets the
lock; removes "as" from completed list and frees it.
5. usbdev_release() is called. Frees "ps".
6. async_completed() finally continues running wake_up(). ...but
wake_up() has a pointer to the freed "ps".
The instrumentation that led me to believe this was based on adding
some trace_printk() calls in a select few functions and then using
kdb's "ftdump" at crash time. The trace follows (NOTE: in the trace
below I cheated a little bit and added a udelay(1000) in
async_completed() after releasing the spinlock because I wanted it to
trigger quicker):
<...>-2104 0d.h2 13759034us!: async_completed at start: as=ffffffc0cc638200
mtpd-2055 3.... 13759356us : async_getcompleted before spin_lock_irqsave
mtpd-2055 3d..1 13759362us : async_getcompleted after list_del_init: as=ffffffc0cc638200
mtpd-2055 3.... 13759371us+: proc_reapurbnonblock_compat: free_async(ffffffc0cc638200)
mtpd-2055 3.... 13759422us+: async_getcompleted before spin_lock_irqsave
mtpd-2055 3.... 13759479us : usbdev_release at start: ps=ffffffc0cc042080
mtpd-2055 3.... 13759487us : async_getcompleted before spin_lock_irqsave
mtpd-2055 3.... 13759497us!: usbdev_release after kfree(ps): ps=ffffffc0cc042080
<...>-2104 0d.h2 13760294us : async_completed before wake_up(): as=ffffffc0cc638200
To fix this problem we can just move the wake_up() under the ps->lock.
There should be no issues there that I'm aware of.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make this const as it is only stored in the type field of a device
structure, which is const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The musb_dsps driver is special in that the parent (glue) device's
driver is accessing registers mapped by the child. The clock is however
shared and is managed by the grandparent device.
Since commit 869c597829 ("usb: musb: dsps: add support for suspend and
resume") the dsps driver has been accessing these registers as part of
suspend and resume.
The parent driver obviously cannot runtime resume the child during
system suspend and is currently relying on the fact that the child will
be RPM_ACTIVE throughout suspend. The suspend implementation also makes
sure to check that the child is indeed present (and hence the clock
enabled) before accessing the registers.
Let's add an explicit runtime resume of the glue device itself to enable
the clock before doing the register accesses in case these assumptions ever
change (i.e. if the child is left runtime suspended).
Note that the glue-timer cancellation is moved after the child-presence
check to keep error handling simple. This should be fine as the timer is
not setup until the controller is being registered and at that time
glue->musb and its driver data have already been initialised.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that the controller is runtime resumed when system suspending
to avoid an external abort when accessing the interrupt registers:
Unhandled fault: external abort on non-linefetch (0x1008) at 0xd025840a
...
[<c05481a4>] (musb_default_readb) from [<c0545abc>] (musb_disable_interrupts+0x84/0xa8)
[<c0545abc>] (musb_disable_interrupts) from [<c0546b08>] (musb_suspend+0x38/0xb8)
[<c0546b08>] (musb_suspend) from [<c04a57f8>] (platform_pm_suspend+0x3c/0x64)
This is easily reproduced on a BBB by enabling the peripheral port only
(as the host port may enable the shared clock) and keeping it
disconnected so that the controller is runtime suspended. (Well, you
would also need to the not-yet-merged am33xx-suspend patches by Dave
Gerlach to be able to suspend the BBB.)
This is a regression that was introduced by commit 1c4d0b4e18 ("usb:
musb: Remove pm_runtime_set_irq_safe") which allowed the parent glue
device to runtime suspend and thereby exposed a couple of older issues:
Register accesses without explicitly making sure the controller is
runtime resumed during suspend was first introduced by commit c338412b5d
("usb: musb: unconditionally save and restore the context on suspend")
in 3.14.
Commit a1fc1920aa ("usb: musb: core: make sure musb is in RPM_ACTIVE on
resume") later started setting the RPM status to active during resume,
and this was also implicitly relying on the parent always being active.
Since commit 71723f9546 ("PM / runtime: print error when activating a
child to unactive parent") this now also results in the following
warning:
musb-hdrc musb-hdrc.0: runtime PM trying to activate child device
musb-hdrc.0 but parent (47401400.usb) is not active
This patch has been verified on 4.13-rc2, 4.12 and 4.9 using a BBB
(the dsps glue would always be active also in 4.8).
Fixes: c338412b5d ("usb: musb: unconditionally save and restore the context on suspend")
Fixes: a1fc1920aa ("usb: musb: core: make sure musb is in RPM_ACTIVE on resume")
Fixes: 1c4d0b4e18 ("usb: musb: Remove pm_runtime_set_irq_safe")
Cc: stable <stable@vger.kernel.org> # 4.8+
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fifo memory allocation in mode_2_cfg[] doesn't utilize all the 4KB
memory.
Increse some endpoint fifo buffers to fully use all the 4KB memory. Now
we can support more webcam usecases on DA8xx.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are multiple places in usb core or controller driver which returns
-EMSGSIZE when a class driver queueing urb failed, so the "Message too
long" log doesn't help much for understanding the error.
Let the musb driver to specifically print a error message when
musb_urb_enqueue() returns -EMSGSIZE.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Print an error message with qh maxpacket size and hb_mult when hwep
allocation failed, so we have a better idea why it is failed.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add helper function musb_ep_xfertype_string() to return the ep transfer
type string.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Add chipidea support at Nvidia SoCs
- Improvement for extcon support
- Some code refines
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZo43vAAoJEEhZKYFQ1nG74W0H/3NsolcVqIzxCnIkRj64AGil
U9xAY0OHWO4cML65LJf7K0oBiRrEkww4TjNGvcm+2Ra9kNjCFsOXdvAkU2JRJ/Ut
xUuBQNBe9diL1SQeJmiL0yTLcnGw0g6f7m0zr3CPiiv/D4iTmMe8v8qJbBYOS0za
tf8DFRArxrOe/YZ4j/RjOqSlGFRErOImzY8QzU6/4TUY7ZTDGZsckHFJsMON2A60
TIiVepBefQboGCZAoB8Lic9eBTJBsiR1H3SQkzZk5Q5wrJ0FitMAwMHXX2ozCe3U
Ahcz0r5176oKAnbP0yKZYx9DzJCCEI30O0iDKEhamnGz3fjc9ydaaUzVamSh5ns=
=0N59
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
Chipidea changes for v4.14-rc1
- Add chipidea support at Nvidia SoCs
- Improvement for extcon support
- Some code refines
The bus_reset handler is really a device reset, so move it to
eh_device_reset_handler().
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
All of these Tegra SoC generations have a ChipIdea UDC IP block that can
be used for device mode communication with a host. Implement rudimentary
support that doesn't allow switching between host and device modes.
Tested-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Thierry Reding <treding@nvidia.com>
[digetx@gmail.com: rebased patches and added DMA alignment quirk for Tegra20]
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
NVIDIA Tegra20 UDC can't cope with unaligned DMA and require a USB gadget
quirk that avoids SKB buffer alignment to be set in order to make Ethernet
Gadget working. Later Tegra generations do not require that quirk. Let's
add a new platform data flag that allows to enable USB gadget quirk for
platforms that require it.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Not a big pull request this time around. Only 49 non-merge
commits. This pull request is, however, all over the place. Most of
the changes are in the bdc driver adding support for USB Phy layer and
PM.
Renesas adds support for R-Car H3 ES2.0 and R-Car M3-W SoCs.
Also here is PM_RUNTIME support for dwc3-keystone.
UDC Core got a DMA unmap fix to make sure we only unmap requests that
were, indeed, mapped.
Other than these, we have a lot of cleanups, many of them adding
'const' to several places.
-----BEGIN PGP SIGNATURE-----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=FSil
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v4.14 merge window
Not a big pull request this time around. Only 49 non-merge
commits. This pull request is, however, all over the place. Most of
the changes are in the bdc driver adding support for USB Phy layer and
PM.
Renesas adds support for R-Car H3 ES2.0 and R-Car M3-W SoCs.
Also here is PM_RUNTIME support for dwc3-keystone.
UDC Core got a DMA unmap fix to make sure we only unmap requests that
were, indeed, mapped.
Other than these, we have a lot of cleanups, many of them adding
'const' to several places.
That quirk is required to make USB Ethernet gadget working on HW that
can't cope with unaligned DMA. For some reason only f_ncm sets up that
quirk, let's setup it directly in u_ether so other network models would
have that quirk applied as well. All network models have been tested with
ChipIdea UDC driver on NVIDIA Tegra20 SoC that require DMA to be aligned.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When the gadget serial device has no associated TTY, do not pass any
received data into the TTY layer for processing; simply drop it instead.
This prevents the TTY layer from calling back into the gadget serial
driver, which will then crash in e.g. gs_write_room() due to lack of
gadget serial device to TTY association (i.e. a NULL pointer dereference).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The usb_add_gadget_udc_release() routine in the USB gadget core will
sometimes but not always call the gadget's release function when an
error occurs. More specifically, if the struct usb_udc allocation
fails then the release function is not called, and for other errors it
is.
As a result, users of this routine cannot know whether they need to
deallocate the memory containing the gadget structure following an
error. This leads to unavoidable memory leaks or double frees.
This patch fixes the problem by splitting the existing
device_register() call into device_initialize() and device_add(), and
doing the udc allocation in between. That way, even if the allocation
fails it is still possible to call device_del(), and so the release
function will be always called following an error.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
bus_resume() tried to resume the same ports the bus_suspend()
suspeded. This caused PLC timeouts in case a suspended device disconnected
and was not in a resumable state at bus_resume().
Add a check to make sure the link state is either U3 or resuming
before actually resuming the link.
At the same time do some other changes such as make sure we remove
wake on connect/disconnect/overcurrent also for the resuming ports,
and avoid extra portsc port register writes.
This improves resume time with 10ms in those PLC timeout cases where
devices disconnect at suspend/resume cycle.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Save 80ms device enumeration time by increasing root hub port reset time
The 50ms reset signaling time is not enough for most root hub ports.
Increasing the reset time to 60ms allows host controllers to finish port
reset and removes a retry causing an extra 50ms delay.
The USB 2 specification requires "at least 50ms" for driving root
port reset. The current msleep is exactly 50ms which may not be
enough if there are any delays between writing the reset bit to host
controller portsc register and phy actually driving reset.
On Haswell, Skylake and Kabylake xHC port reset took in average 52-59ms
The 80ms improvement comes from (40ms * 2 port resets) save at enumeration
for each device connected to a root hub port.
more details about root port reset in USB2 section 7.1.7.5:.
"Software must ensure that resets issued to the root ports drive reset
long enough to overwhelm any concurrent resume attempts by downstream
devices. It is required that resets from root ports have a duration of
at least 50 ms (TDRSTR).
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Track the port status in a human readble way each time we get a
port status change event
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
temp and temp1 variables are used for port status (portsc) and
command register. Give them more descriptive names
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add PORTSC Port status and control register decoder to
show human readable tracing of portsc register
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add definitions for all port link states defined in xhci
specification for PORTSC register.
Will be needed for human readable port status tracing
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for R-Car H3 ES2.0. Since this SoC revision
(or later) should use the V3 firmware, the driver needs to check
the revision via soc_device_match().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the firmware_name is decided by xhci-rcar.c on R-Car Gen3 now,
this patch removes 2 things:
- Remove struct xhci_plat_priv xhci_plat_renesas_rcar_r8a7796.
- Remoce .firmware_name from xhci_plat_renesas_rcar_gen3.
The behavior is the same as before.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds firmware_name selection by soc_device_match() to
use other firmware name in the future. (For now, using the firmware
is the same as before.)
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces the deprecated extcon API as following:
- extcon_get_cable_state_() -> extcon_get_state()
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch introduces the usb charger support based on usb phy that
makes an enhancement to a power driver. The basic conception of the
usb charger is that, when one usb charger is added or removed by
reporting from the extcon device state change, the usb charger will
report to power user to set the current limitation.
Power user can register a notifiee on the usb phy by issuing
usb_register_notifier() to get notified by charger status changes
or charger current changes.
we can notify what current to be drawn to power user according to
different charger type, and now we have 2 methods to get charger type.
One is get charger type from extcon subsystem, which also means the
charger state changes. Another is we can get the charger type from
USB controller detecting or PMIC detecting, and the charger state
changes should be told by issuing usb_phy_set_charger_state().
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Users can apply i/o in the wrong direction on an
endpoint to stall it. In case there is an error
that does not allow the endpoint to be stalled,
we want the user to know.
An operation to stall the endpoint will return
EBADMSG if successful, EAGAIN if there are still
queued requests, and other errors depending on
the underlying implementation.
Also remove the conditional since it is always true.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Jerry Zhang <zhangjerry@google.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If a phy is specified in the device tree node, get it and use it.
This was based on a patch by:
"Srinath Mannam <srinath.mannam@broadcom.com>"
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Many ARM based Broadcom STB SoC's have a USB BDC controller so
enable this driver for these systems.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch essentially clears the port status change bits at the
correct times. It is necessary because the driver was not handling
the change bits correctly for events during device
connection/disconnection and bus enumeration. So, one of them (PCC)
was left stuck sometimes causing the "xsf for ep not enabled"
error we get on first connection. This was found by the Android team.
This was debugged and fixed by Sasi Kumar.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Based on a previous commit by Danesh Petigara <dpetigara@broadcom.com>
that added resume to solve the following problem:
"The BDC driver will fail after resuming from S3 suspend and this
will cause any upper layer gadget driver to fail."
This commit also adds support for suspend and manages the clock during
suspend/resume.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Allows Device Tree probing
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Newer SoC's have added a BDC clock to the Device Tree, so get
and enable it.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The BDC endpoint status registers 0-7 were originally each going
to be an array of regsiters. This was later changed to being a
single register. The register definitions are being changed from:
"#define BDC_EPSTS0(n) (0x60 + (n * 0x10))"
to
"#define BDC_EPSTS0 0x60"
to reflect this change and to avoid future coding mistakes.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This adds 3 new options to the RNDIS gadget function configs. It allows
overriding the default USB interface class/subclass/protocol.
The motivation for this is that if you set the values to "ef" (Misc),
"04" (RNDIS), "01" (Ethernet) respectively, then the device will be
recognized by the rndiscmp.inf file in Windows Vista and newer and will
cause Windows to load the correct RNDIS driver without the need for a
custom (signed) .inf file.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work with
const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work with
const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In the case hcd autosuspend is enabled, the hcd will enter L2 state
if no device connected. But if the controller works in otg mode, the
gadget driver still works in L0 state if connected with host. This
may result in transfer fail when gadget enqueue new request but the
hcd driver has set the global state into L2. This patch prevent the
hcd enter L2 state if the controller work in device mode.
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes an issue that the spin_lock_init() is not called
for almost all pipes. Otherwise, the lockdep output the following
message when we connect a usb cable using g_ncm:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
Reported-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Fixes: b8b9c974af ("usb: renesas_usbhs: gadget: disable all eps when the driver stops")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In the SG case this is already handled since a non-zero
request->num_mapped_sgs is a clear indicator that dma_map_sg()
had been called. While it would be nice to do the same for the
singly mapped case by simply checking for non-zero request->dma,
it's conceivable that 0 is a valid dma_addr_t handle. Hence add
a flag 'dma_mapped' to struct usb_request and use this to
determine the need to call dma_unmap_single(). Otherwise, if a
request is not DMA mapped then the result of calling
usb_request_unmap_request() would safely be a no-op.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
USB gadget serial console works on functions other than the legacy
configurations. Let the user enable it when using any function that
uses the serial utilities.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@cascardo.eti.br>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Make the structure const as it is only stored in the ops field of a
usb_ep structure, which is of type const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Make the structure const as it is only stored in the ops field of a
usb_ep structure, which is of type const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Make the structure const as it is only stored in the ops field of a
usb_ep structure, which is of type const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The header clk-provider.h is there for clock drivers (providers) to
include, not client drivers (consumers). That said,
of_clk_get_parent_count() is a helper function for clock providers, not
a clk API for consumers.
Let's replace of_clk_get_parent_count() with of_count_phandle_with_args()
call, so that we can remove the include of clk-provider.h.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Currenly, f_midi_free uses snd_card_free, which will wait
until the user has released the sound card before
returning. However, if the user doesn't release the sound
card, then f_midi_free can block for an arbitrary amount
of time, which also blocks any gadget operations on that
thread.
Instead, we can use snd_card_free_when_closed which returns
before all handles are released. Since f_midi can be
accessed through rmidi if usb_put_function is called before
release_card_device, add refcounting to f_midi_free and
have rawmidi's private free call it. The f_midi memory
is only kfreed when usb_put_function and release_card_device
have both been called.
Signed-off-by: Jerry Zhang <zhangjerry@google.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add super speed descriptors for f_midi.
Signed-off-by: Badhri Jagan Sridharan <Badhri@google.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The while loop never terminates because the loop counter i is never
decremented. Fix this by decrementing i.
Detected by CoverityScan, CID#751073 ("Infinite Loop")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
These snd_rawmidi_ops structures are only passed as the third
argument of snd_rawmidi_set_ops. This argument is const, so the
snd_rawmidi_ops structures can be const too.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The mtu3 driver is a generic driver for MediaTek usb3 DRD IP, add
a generic compatible to avoid confusion when support new SoCs but
use a compatible with specific SoC's name "mt8173".
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The current f_hid driver doesn't handle GET_PROCOTOL and
SET_PROCOTOL requests, which are required to operate HID
gadgets in BOOT mode. This patch implements this feature for
devices that have the same implementation for REPORT and BOOT mode
so that these devices are recognized by older BIOSes.
Signed-off-by: Abdulhadi Mohamed <abdulahhadi2@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Ip sleep will auto exit if vbus comparison circuit of u2 phy is
disabled when system tries to enter suspend mode, so get vbus-valid
status from mac but not from u2 phy when enable DRD mode to fix
the issue.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
when the device is reset by host, the status of u1_enable and
u2_enable should also be restored to default value.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add the delayed status handling. This is used by mass storage etc to
gain some extra time to setup its internal status before it can proceed
further requests, and once the gadget is ready, it will enqueue an
empty packet which is used for synchronization.
The issue may happen on some FGPA platform with very low cpu frequency.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Using devm_ioremap_resource() can make the code simpler, as it
already does the resource NULL check.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
qe_ep0_desc is only passed as the second argument to qe_ep_init, which is
const, so qe_ep0_desc can be const too.
Done with the help of Coccinelle.
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds support for R-Car M3-W. This patch also adds R-Car
Gen3 generic version's compatible and changes ".compatible" in
the usb3_of_match from "renesas,r8a7796-usb3-peri" to
"renesas,rcar-gen3-usb3-peri".
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Here are a number of small USB driver fixes and new device ids for
4.13-rc5. There is the usual gadget driver fixes, some new quirks for
"messy" hardware, and some new device ids.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWY+2eA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynSGACgrMjsqOsgjgVEnc1IdjS2gHEZnfcAoMmyBGwo
cNOM+8gnysJLFUTwkppl
=+bPU
-----END PGP SIGNATURE-----
Merge tag 'usb-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of small USB driver fixes and new device ids for
4.13-rc5. There is the usual gadget driver fixes, some new quirks for
"messy" hardware, and some new device ids.
All have been in linux-next with no reported issues"
* tag 'usb-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: serial: pl2303: add new ATEN device id
usb: quirks: Add no-lpm quirk for Moshi USB to Ethernet Adapter
USB: Check for dropped connection before switching to full speed
usb:xhci:Add quirk for Certain failing HP keyboard on reset after resume
usb: renesas_usbhs: gadget: fix unused-but-set-variable warning
usb: renesas_usbhs: Fix UGCTRL2 value for R-Car Gen3
usb: phy: phy-msm-usb: Fix usage of devm_regulator_bulk_get()
usb: gadget: udc: renesas_usb3: Fix usb_gadget_giveback_request() calling
usb: dwc3: gadget: Correct ISOC DATA PIDs for short packets
USB: serial: option: add D-Link DWM-222 device ID
usb: musb: fix tx fifo flush handling again
usb: core: unlink urbs from the tail of the endpoint's urb_list
usb-storage: fix deadlock involving host lock and scsi_done
uas: Add US_FL_IGNORE_RESIDUE for Initio Corporation INIC-3069
USB: hcd: Mark secondary HCD as dead if the primary one died
USB: serial: cp210x: add support for Qivicon USB ZigBee dongle
This adds a new ATEN device id for a new pl2303-based device.
Reported-by: Peter Kuo <PeterKuo@aten.com.tw>
Cc: stable <stable@vger.kernel.org>
Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Moshi USB to Ethernet Adapter internally uses a Genesys Logic hub to
connect to Realtek r8153.
The Realtek r8153 ethernet does not work on the internal hub, no-lpm quirk
can make it work.
Since another r8153 dongle at my hand does not have the issue, so add
the quirk to the Genesys Logic hub instead.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some buggy USB disk adapters disconnect and reconnect multiple times
during the enumeration procedure. This may lead to a device
connecting at full speed instead of high speed, because when the USB
stack sees that a device isn't able to enumerate at high speed, it
tries to hand the connection over to a full-speed companion
controller.
The logic for doing this is careful to check that the device is still
connected. But this check is inadequate if the device disconnects and
reconnects before the check is done. The symptom is that a device
works, but much more slowly than it is capable of operating.
The situation was made worse recently by commit 22547c4cc4 ("usb:
hub: Wait for connection to be reestablished after port reset"), which
increases the delay following a reset before a disconnect is
recognized, thus giving the device more time to reconnect.
This patch makes the check more robust. If the device was
disconnected at any time during enumeration, we will now skip the
full-speed handover.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Zdenek Kabelac <zkabelac@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Certain HP keyboards would keep inputting a character automatically which
is the wake-up key after S3 resume
On some AMD platforms USB host fails to respond (by holding resume-K) to
USB device (an HP keyboard) resume request within 1ms (TURSM) and ensures
that resume is signaled for at least 20 ms (TDRSMDN), which is defined in
USB 2.0 spec. The result is that the keyboard is out of function.
In SNPS USB design, the host responds to the resume request only after
system gets back to S0 and the host gets to functional after the internal
HW restore operation that is more than 1 second after the initial resume
request from the USB device.
As a workaround for specific keyboard ID(HP Keyboards), applying port reset
after resume when the keyboard is plugged in.
Signed-off-by: Sandeep Singh <Sandeep.Singh@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Reviewed-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Provides a new vbus debugfs interface used to turn on/off vbus
regulator, it also can be used to get/put reference count of
vbus, due to sometimes we need keep it alive when manually switch
mtu3 to device mode.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_get_irq() returns an error code, but the imx21-hcd driver
ignores it and always returns -ENXIO. This is not correct, and
prevents -EPROBE_DEFER from being propagated properly.
Notice that platform_get_irq() no longer returns 0 on error:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e330b9a6bb35dc7097a4f02cb1ae7b6f96df92af
Print error message and propagate the return value of platform_get_irq
on failure.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_get_irq() returns an error code, but the ehci-omap driver
ignores it and always returns -ENODEV. This is not correct and,
prevents -EPROBE_DEFER from being propagated properly.
Also, notice that platform_get_irq() no longer returns 0 on error:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e330b9a6bb35dc7097a4f02cb1ae7b6f96df92af
Print and propagate the return value of platform_get_irq on failure.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
qe_ep0_desc is only passed as the second argument to qe_ep_init, which is
const, so qe_ep0_desc can be const too.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work with
const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work with
const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work with
const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work with
const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work with
const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work with
const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work with
const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work with
const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work with
const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work with
const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work with
const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dev_pm_ops is not supposed to change at runtime. Marking it
constant.
Signed-off-by: Doug Wilson <doug.wilson@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
snd_pcm_ops are not supposed to change at runtime. All functions
working with snd_pcm_ops provided by <sound/pcm.h> work with
const snd_pcm_ops. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make these const as they are only passed to the function
atm_dev_register and the corresponding argument is of type const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for R-Car H3 ES2.0. Since this SoC revision
doesn't need workaround for vbus detection and number of ramif is
increased. So, this driver uses soc_device_match() to detect it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds debugfs to set the "b-device" mode for using a board
which is not connected to the ID pin (e.g. CN11 on Salvator-X).
If we want to use peripheral mode on such a board, we have to disable
VBUS output first. So, this patch can set such a mode as the following:
# mount -t debugfs none /sys/kernel/debug
# modprobe renesas_usb3
# modprobe g_mass_storage file=/dev/shm/test.bin
# echo 1 > /sys/kernel/debug/ee020000.usb/b_device
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Provides a new vbus debugfs interface used to turn on/off vbus
regulator, it also can be used to get/put reference count of
vbus, due to sometimes we need keep it alive when manually switch
mtu3 to device mode.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For 66AK2Gx there is a requirement to use PM Runtime to properly manage
clocks and the power domains. Therefore, add PM runtime support. Remove
legacy clock api's calls since other users of this driver worked without
these clock apis calls.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
platform_get_irq() returns an error code, but the dwc3-omap driver
ignores it and always returns -EINVAL. This is not correct and,
prevents -EPROBE_DEFER from being propagated properly.
Notice that platform_get_irq() no longer returns 0 on error:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e330b9a6bb35dc7097a4f02cb1ae7b6f96df92af
Print and propagate the return value of platform_get_irq on failure.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dev_pm_ops is not supposed to change at runtime. Marking it constant.
Signed-off-by: Doug Wilson <doug.wilson@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
platform_get_irq() returns an error code, but the renesas_usb3 driver
ignores it and always returns -ENODEV. This is not correct and,
prevents -EPROBE_DEFER from being propagated properly.
Also, notice that platform_get_irq() no longer returns 0 on error:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e330b9a6bb35dc7097a4f02cb1ae7b6f96df92af
Print error message and propagate the return value of platform_get_irq
on failure.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
snd_pcm_ops are not supposed to change at runtime. All functions
working with snd_pcm_ops provided by <sound/pcm.h> work with
const snd_pcm_ops. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Here are some new device ids for v4.13-rc4.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=bRO0
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.13-rc4
Here are some new device ids for v4.13-rc4.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
Felipe writes:
usb: fixes for v4.13-rc4
Another fix for isochronous transfers on dwc3. This time around, we're
making sure that we use correct PIDs in all transfer sizes.
MSM PHY driver got a fix for the use of devm_regulator_bulk_get() API
which will avoid kernel crashes.
Renesas DRD driver got 3 fixes: a fix on giveback, a fix for proper
controller programming and the removal of set-but-never-used variable.
The commit b8b9c974af ("usb: renesas_usbhs: gadget: disable all eps
when the driver stops") causes the unused-but-set-variable warning.
But, if the usbhsg_ep_disable() will return non-zero value, udc/core.c
doesn't clear the ep->enabled flag. So, this driver should not return
non-zero value, if the pipe is zero because this means the pipe is
already disabled. Otherwise, the ep->enabled flag is never cleared
when the usbhsg_ep_disable() is called by the renesas_usbhs driver first.
Fixes: b8b9c974af ("usb: renesas_usbhs: gadget: disable all eps when the driver stops")
Fixes: 11432050f0 ("usb: renesas_usbhs: gadget: fix NULL pointer dereference in ep_disable()")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The latest HW manual (Rev.0.55) shows us this UGCTRL2.VBUSSEL bit.
If the bit sets to 1, the VBUS drive is controlled by phy related
registers (called "UCOM Registers" on the manual). Since R-Car Gen3
environment will control VBUS by phy-rcar-gen3-usb2 driver,
the UGCTRL2.VBUSSEL bit should be set to 1. So, this patch fixes
the register's value. Otherwise, even if the ID pin indicates to
peripheral, the R-Car will output USBn_PWEN to 1 when a host driver
is running.
Fixes: de18757e27 ("usb: renesas_usbhs: add R-Car Gen3 power control"
Cc: <stable@vger.kernel.org> # v4.6+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The regulator_bulk_data pointer passed to devm_regulator_bulk_get()
is used to store the client handles for the regulators, which
is later used by devm_regulator_bulk_release() to free the
regulators.
Passing a local array as is done here means the memory used to
store the handles is freed causing the handles to be corrupted,
resulting in a crash when devm_regulator_bulk_release() tries to
free them.
Fix this my moving the array inside of the msm_otg structure.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
According to the gadget.h, a "complete" function will always be called
with interrupts disabled. However, sometimes usb3_request_done() function
is called with interrupts enabled. So, this function should be held
by spin_lock_irqsave() to disable interruption. Also, this driver has
to call spin_unlock() to avoid spinlock recursion by this driver before
calling usb_gadget_giveback_request().
Reported-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Tested-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Fixes: 746bfe63bb ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The PIDs for Isochronous data transfers are incorrect
for high bandwidth IN endpoints when the request length
is less than EP wMaxPacketSize.
As per spec correct PIDs for ISOC data transfers are:
1) For request length <= maxpacket
- DATA0,
2) For maxpacket < length <= (2 * maxpacket)
- DATA1, DATA0
3) For (2 * maxpacket) < length <= (3 * maxpacket)
- DATA2, DATA1, DATA0.
But driver always sets PCM fields based on wMaxPacketSize
due to which DATA2 happens even for small requests.
Fix this by setting the PCM field of trb->size depending
on request length rather than fixing it to the value
depending on wMaxPacketSize.
Ideally it shouldn't give any issues as dwc3 will send
0-length packet for next IN token if host sends (even
after receiving a short packet). Windows seems to ignore
this but with MacOS frame loss observed when using f_uvc.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The Renesas uPD72020x XHCI controller seems to suffer from a really
annoying bug, where it may retain some of its DMA programming across a XHCI
reset, and despite the driver correctly programming new DMA addresses.
This is visible if the device has been using 64-bit DMA addresses, and is
then switched to using 32-bit DMA addresses. The top 32 bits of the
address (now zero) are ignored are replaced by the 32 bits from the
*previous* programming. Sticking with 64-bit DMA always works, but doesn't
seem very appropriate.
A PCI reset of the device restores the normal functionality, which is done
at probe time. Unfortunately, this has to be done before any quirk has
been discovered, hence the intrusive nature of the fix.
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
CC: stable@vger.kernel.org # v4.11+
Add device id for D-Link DWM-222.
Cc: stable@vger.kernel.org
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Johan Hovold <johan@kernel.org>
The hc_driver structure is only passed as the first argument to
usb_create_hcd, which is declared as const. Thus the hc_driver structure
itself can be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hc_driver structure is only passed as the first argument to
usb_create_hcd, which is declared as const. Thus the hc_driver structure
itself can be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hc_driver structure is only passed as the first argument to
usb_create_hcd, which is declared as const. Thus the hc_driver structure
itself can be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hc_driver structure is only passed as the first argument to
usb_create_hcd, which is declared as const. Thus the hc_driver structure
itself can be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hc_driver structure is only passed as the first argument to
usb_create_hcd, which is declared as const. Thus the hc_driver structure
itself can be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hc_driver structure is only passed as the first argument to
usb_create_hcd, which is declared as const. Thus the hc_driver structure
itself can be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hc_driver structure is only passed as the first argument to
usb_create_hcd, which is declared as const. Thus the hc_driver structure
itself can be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hc_driver structure is only passed as the first argument to
usb_create_hcd, which is declared as const. Thus the hc_driver structure
itself can be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hc_driver structure is only passed as the first argument to
usb_create_hcd, which is declared as const. Thus the hc_driver structure
itself can be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hc_driver structure is only passed as the first argument to
usb_create_hcd, which is declared as const. Thus the hc_driver structure
itself can be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ip sleep will auto exit if vbus comparison circuit of u2 phy is
disabled when system tries to enter suspend mode, so get vbus-valid
status from mac but not from u2 phy when enable DRD mode to fix
the issue.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when the device is reset by host, the status of u1_enable and
u2_enable should also be restored to default value.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the delayed status handling. This is used by mass storage etc to
gain some extra time to setup its internal status before it can proceed
further requests, and once the gadget is ready, it will enqueue an
empty packet which is used for synchronization.
The issue may happen on some FGPA platform with very low cpu frequency.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68fe05e2a4 ("usb: musb: fix tx fifo flush handling") drops the
1ms delay trying to solve the long disconnect time issue when
application queued many tx urbs. However, the 1ms delay is needed for
some use cases, for example, without the delay, reconnecting AR9271 WIFI
dongle no longer works if the connection is dropped from the AP.
So let's add back the 1ms delay in musb_h_tx_flush_fifo(), and solve the
long disconnect time problem with a separate patch for
usb_hcd_flush_endpoint().
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While unlink an urb, if the urb has been programmed in the controller,
the controller driver might do some hw related actions to tear down the
urb.
Currently usb_hcd_flush_endpoint() passes each urb from the head of the
endpoint's urb_list to the controller driver, which could make the
controller driver think each urb has been programmed and take the
unnecessary actions for each urb.
This patch changes the behavior in usb_hcd_flush_endpoint() to pass the
urbs from the tail of the list, to avoid any unnecessary actions in an
controller driver.
Cc: stable@vger.kernel.org # v4.4+
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christoph Hellwig says that since version 4.12, the kernel switched to
using blk-mq by default. The old code used a softirq for handling
request completions, but blk-mq can handle completions in the caller's
context. This may cause a problem for usb-storage, because it invokes
the ->scsi_done callback while holding the host lock, and the
completion routine sometimes tries to acquire the same lock (when
running the error handler, for example).
The consequence is that the existing code will sometimes deadlock upon
error completion of a SCSI command (with a lockdep warning).
This is easy enough to fix, since usb-storage doesn't really need to
hold the host lock while the callback runs. It was simpler to write
it that way, but moving the call outside the locked region is pretty
easy and there's no downside. That's what this patch does.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Arthur Marsh <arthur.marsh@internode.on.net>
CC: Christoph Hellwig <hch@lst.de>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Similar to commit d595259fbb ("usb-storage: Add ignore-residue quirk for
Initio INIC-3619") for INIC-3169 in unusual_devs.h but INIC-3069 already
present in unusual_uas.h. Both in same controller IC family.
Issue is that MakeMKV fails during key exchange with installed bluray drive
with following error:
002004:0000 Error 'Scsi error - ILLEGAL REQUEST:COPY PROTECTION KEY EXCHANGE FAILURE - KEY NOT ESTABLISHED'
occurred while issuing SCSI command AD010..080002400 to device 'SG:dev_11:0'
Signed-off-by: Alan Swanson <reiver@improbability.net>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make usb_hc_died() clear the HCD_FLAG_RH_RUNNING flag for the shared
HCD and set HCD_FLAG_DEAD for it, in analogy with what is done for
the primary one.
Among other thigs, this prevents check_root_hub_suspended() from
returning -EBUSY for dead HCDs which helps to work around system
suspend issues in some situations.
This actually fixes occasional suspend failures on one of my test
machines.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This issue is detected when the system has another device driver
which registers USB connector extcon device, fix it by adding
extcon device check.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The controller driver may be NULL if the controller device
is the middle device between platform device and roothub.
This middle device may not need a device driver due to all
hardware control can be at platform device driver, this
platform device is usually a dual-role USB controller device.
The benefit of using this middle device is we can keep both
controller device's private data (known as struct usb_hcd)
for USB core use, and platform device's private data for
platform driver use.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MODULE_VERSION is useless for in-kernel drivers, so just remove all
usage of it in the USB ATM drivers. Along with this, some
DRIVER_VERSION macros were removed as they are also pointless.
Cc: Duncan Sands <duncan.sands@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MODULE_VERSION is useless for in-kernel drivers, so remove the use of it
in the chipidea CI13XXX driver.
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No one uses the DRIVER_VERSION define in this driver, so just delete it.
Cc: Oliver Neukum <oneukum@suse.com>
Cc: "Bjørn Mork" <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MODULE_VERSION is useless for in-kernel drivers, so just remove all
usage of it in the USB gadget drivers. Along with this, some
DRIVER_VERSION macros were removed as they are also pointless.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No one uses the DRIVER_VERSION define in this driver, so just delete it.
Cc: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MODULE_VERSION is useless for in-kernel drivers, so remove the
use of it in the marvel phy driver, along with the DRIVER_VERSION
define.
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MODULE_VERSION is useless for in-kernel drivers, so remove the
use of it in the Realtek USB card reader driver.
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MODULE_VERSION is useless for in-kernel drivers, so just remove all
usage of it in the USB usbip drivers. Along with this, the
USBIP_VERSION macros was removed as is was also pointless, as well as
printing out the driver version to the syslog at init time, which is not
necessary at all.
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MODULE_VERSION is useless for in-kernel drivers, so just remove all
usage of it in the USB misc drivers. Along with this, some
DRIVER_VERSION macros were removed as they are also pointless.
Cc: Keith Packard <keithp@keithp.com>
Cc: Juergen Stuber <starblue@users.sourceforge.net>
Cc: Cesar Miquel <miquel@df.uba.ar>
Acked-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both xhci_hub_control and xhci_disable_slot tries to hold spinlock, the
spinlock recursion occurs when enters USB2 test mode. Fix it by unlock
spinlock before calling xhci_disable_slot.
Cc: <stable@vger.kernel.org>
Fixes: 0f1d832ed1 ("usb: xhci: Add port test modes support for usb2")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A uncleared PLC (port link change) bit will prevent furuther port event
interrupts for that port. Leaving it uncleared caused get_port_status()
to timeout after 20000ms while waiting to get the final port event
interrupt for resume -> U0 state change.
This is a targeted fix for a specific case where we get a port resume event
racing with xhci resume. The port event interrupt handler notices xHC is
not yet running and bails out early, leaving PLC uncleared.
The whole xhci port resuming needs more attention, but while working on it
it anyways makes sense to always ensure PLC is cleared in get_port_status
before setting a new link state and waiting for its completion.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
on AMD platforms with SNPS 3.1 USB controller if stop endpoint command is
issued the controller does not respond, when the EP is not in running
state. HW completes the command execution and reports
"Context State Error" completion code. This is as per the spec. However
HW on receiving the second command additionally marks EP to Flow control
state in HW which is RTL bug. This bug causes the HW not to respond
to any further doorbells that are rung by the driver. This makes the EP
to not functional anymore and causes gross functional failures.
As a workaround, not to hit this problem, it's better to check the EP state
and issue a stop EP command only when the EP is in running state.
As a sidenote, even with this patch there is still a possibility of
triggering the RTL bug if the context state races with the stop endpoint
command as described in xHCI spec 4.6.9
[code simplification and reworded sidenote in commit message -Mathias]
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When USB Ethernet is plugged in ASMEDIA ASM1042A xHCI host, bad
performance was manifesting in Web browser use (like download
large file such as ISO image). It is known limitation of
ASM1042A that is not compatible with driver scheduling,
As a workaround we can modify flow control handling of ASM1042A.
The register we modify is changes the behavior
[use quirk bit 28, usleep_range 40-60us, empty non-pci function -Mathias]
Cc: <stable@vger.kernel.org>
Signed-off-by: Jiahau Chang <Lars_chang@asmedia.com.tw>
Signed-off-by: Ian Pilcher <arequipeno@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This off by one in stream_id indexing caused NULL pointer dereference and
soft lockup on machines with USB attached SCSI devices connected to a
hotpluggable xhci controller.
The code that cleans up pending URBs for dead hosts tried to dereference
a stream ring at the invalid stream_id 0.
ep->stream_info->stream_rings[0] doesn't point to a ring.
Start looping stream_id from 1 like in all the other places in the driver,
and check that the ring exists before trying to kill URBs on it.
Reported-by: rocko r <rockorequin@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
First set of fixes for the current -rc cycle. Only three fixes on dwc3
this time around (proper order for getting a PHY reference, fix for
unmapping DMA and a fix for requesting IRQ on the OMAP glue layer).
Most fixes are on the renesas USB controller, fixing several old bugs
with most going to stable.
dwc2 also learned that it *must* reset USB Address to zero on Reset
interrupts.
Apart from these, some drivers needed HAS_DMA dependency and there's a
sparse warning fix for bdc udc.
-----BEGIN PGP SIGNATURE-----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=eMHd
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.13-rc2
First set of fixes for the current -rc cycle. Only three fixes on dwc3
this time around (proper order for getting a PHY reference, fix for
unmapping DMA and a fix for requesting IRQ on the OMAP glue layer).
Most fixes are on the renesas USB controller, fixing several old bugs
with most going to stable.
dwc2 also learned that it *must* reset USB Address to zero on Reset
interrupts.
Apart from these, some drivers needed HAS_DMA dependency and there's a
sparse warning fix for bdc udc.
A gadget driver will not disable eps immediately when ->disconnect()
is called. But, since this driver assumes all eps stop after
the ->disconnect(), unexpected behavior happens (especially in system
suspend).
So, this patch disables all eps in usbhsg_try_stop(). After disabling
eps by renesas_usbhs driver, since some functions will be called by
both a gadget and renesas_usbhs driver, renesas_usbhs driver should
protect uep->pipe. To protect uep->pipe easily, this patch adds a new
lock in struct usbhsg_uep.
Fixes: 2f98382dc ("usb: renesas_usbhs: Add Renesas USBHS Gadget")
Cc: <stable@vger.kernel.org> # v3.0+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes an issue that some registers may be not initialized
after resume if the USBHSF_RUNTIME_PWCTRL is not set. Otherwise,
if a cable is not connected, the driver will not enable INTENB0.VBSE
after resume. And then, the driver cannot detect the VBUS.
Fixes: ca8a282a53 ("usb: gadget: renesas_usbhs: add suspend/resume support")
Cc: <stable@vger.kernel.org> # v3.2+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Boot fails for qcom-apq8074-dragonboard on 4.13-rc1 with error:
OF: ERROR: Bad of_node_put() on /soc/usb@f9a55000
The error will occur if the configuration is set to:
CONFIG_OF_OVERLAY y
CONFIG_OF_UNITTEST y
CONFIG_OF_DYNAMIC y
CONFIG_OF_RESOLVE y
If CONFIG_OF_DYNAMIC is enabled then of_node_release() detects an
attempt to release a node that is still attached to the device tree.
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Simplify return logic to avoid unnecessary variable assignment.
This issue was detected using Coccinelle and the following
semantic patch:
@@
local idexpression ret;
expression e;
@@
-ret =
+return
e;
-return ret;
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
This patch fixes an issue that unexpected behavior happens when
both the interrupt handler and renesas_usb3_ep_enable() are called.
In this case, since usb3_start_pipen() checked the usb3_ep->started,
but the flags was not protected. So, this patch protects the flag
by usb3->lock. Since renesas_usb3_ep_enable() for EP0 will be not called,
this patch doesn't take care of usb3_start_pipe0().
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The dedicated dmac can transfer a zero-length-packet (zlp) if some bits
of the USB_COM_CON register. However, the commit 2d4aa21a73 ("usb:
gadget: udc: renesas_usb3: add support for dedicated DMAC") didn't set
the bits to 1. So, this patch fixes it.
Fixes: 2d4aa21a73 ("usb: gadget: udc: renesas_usb3: add support for dedicated DMAC)
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The commit 2d4aa21a73 ("usb: gadget: udc: renesas_usb3: add support
for dedicated DMAC") has a bug in the renesas_usb3_dma_free_prd().
The size of dma_free_coherent() should be the same with dma_alloc_coherent()
Otherwise, this code causes a WARNING by mm/page_alloc.c when
renesas_usb3_dma_free_prd() is called. So, this patch fixes it.
Fixes: 2d4aa21a73 ("usb: gadget: udc: renesas_usb3: add support for dedicated DMAC")
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
As per USB spec, multiple-bytes fields are stored
in little-endian order. Use CPU<->LE helpers for
such fields.
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
As per USB spec, multiple-bytes fields are stored
in little-endian order. Use CPU<->LE helpers for
such fields.
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fixes the following Sparse warnings:
>> drivers/usb/gadget/udc/snps_udc_plat.c:31:6: sparse: symbol 'start_udc' was not declared. Should it be static?
>> drivers/usb/gadget/udc/snps_udc_plat.c:41:6: sparse: symbol 'stop_udc' was not declared. Should it be static?
>> drivers/usb/gadget/udc/snps_udc_plat.c:79:6: sparse: symbol 'udc_drd_work' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Reseted DEVADDR field in DCFG to zero on USB RESET.
Device address in DCFG register does not reset to zero,
which required to pass enumeration, after disconnect and
reconnect.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Trivial fix to spelling mistake in uea_err error message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Array type_array can be made static const rather than being
populated on the stack. Makes the object code smaller:
Before:
text data bss dec hex filename
8087 1496 0 9583 256f drivers/usb/renesas_usbhs/pipe.o
After:
text data bss dec hex filename
7883 1584 0 9467 24fb drivers/usb/renesas_usbhs/pipe.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify return logic to avoid unnecessary variable declaration
and assignment.
This issue was detected using Coccinelle and the following
semantic patch:
@@
local idexpression ret;
expression e;
@@
-ret =
+return
e;
-return ret;
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify return logic to avoid unnecessary variable declaration
and assignment.
These issues were detected using Coccinelle and the following
semantic patch:
@@
local idexpression ret;
expression e;
@@
-ret =
+return
e;
-return ret;
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify return logic to avoid unnecessary variable assignment.
This issue was detected using Coccinelle and the following
semantic patch:
@@
local idexpression ret;
expression e;
@@
-ret =
+return
e;
-return ret;
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When us->extra is null the driver is not initialized, however, a
later call to osd200_scsi_to_ata is made that dereferences
us->extra, causing a null pointer dereference. The code
currently detects and reports that the driver is not initialized;
add a return to avoid the subsequent dereference issue in this
check.
Thanks to Alan Stern for pointing out that srb->result needs setting
to DID_ERROR << 16
Detected by CoverityScan, CID#100308 ("Dereference after null check")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new driver causes a build failure in some configurations:
In file included from /git/arm-soc/drivers/usb/typec/ucsi/trace.h:9:0,
from /git/arm-soc/drivers/usb/typec/ucsi/trace.c:2:
drivers/usb/typec/ucsi/ucsi.h:331:39: error: 'struct device' declared inside parameter list will not be visible outside of this definition or declaration [-Werror]
This includes the required header file.
Fixes: c1b0bc2dab ("usb: typec: Add support for UCSI interface")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The German Telekom offers a ZigBee USB Stick under the brand name Qivicon
for their SmartHome Home Base in its 1. Generation. The productId is not
known by the according kernel module, this patch adds support for it.
Signed-off-by: Stefan Triller <github@stefantriller.de>
Reviewed-by: Frans Klaver <fransklaver@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
A recent optimization was made so that a request put on the
pending_list wouldn't get mapped for DMA until just before
preparing a TRB for it. However, this poses a problem in case
the request is dequeued or the endpoint is disabled before the
mapping is done as that would lead to dwc3_gadget_giveback()
unconditionally calling usb_gadget_unmap_request_for_dev() with
an invalid request->dma handle. Depending on the platform's DMA
implementation the unmap operation could result in a panic.
Since we know a successful mapping is a prerequisite for getting
a TRB, the unmap can be conditionally called only when req->trb
is non-NULL.
Fixes: cdb55b39fa ("usb: dwc3: gadget: lazily map requests for DMA")
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If NO_DMA=y:
ERROR: "usb_gadget_map_request" [drivers/usb/gadget/udc/snps_udc_core.ko] undefined!
ERROR: "dma_pool_destroy" [drivers/usb/gadget/udc/snps_udc_core.ko] undefined!
ERROR: "usb_gadget_unmap_request" [drivers/usb/gadget/udc/snps_udc_core.ko] undefined!
ERROR: "dma_pool_free" [drivers/usb/gadget/udc/snps_udc_core.ko] undefined!
ERROR: "dma_pool_alloc" [drivers/usb/gadget/udc/snps_udc_core.ko] undefined!
ERROR: "dma_pool_create" [drivers/usb/gadget/udc/snps_udc_core.ko] undefined!
As USB_SNP_CORE is selected by USB_SNP_UDC_PLAT and USB_AMD5536UDC,
these should depend on HAS_DMA, too. For USB_AMD5536UDC, this is
already fulfilled through the dependency on USB_PCI (PCI implies
HAS_DMA).
Add dependencies on HAS_DMA to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It is wrong to do --i in the for loop.
Fixes: dd02ea5a33 ("usb: gadget: mass_storage: Use static array for luns")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
IRQ_NOAUTOEN cannot be used with shared IRQs, since commit 04c848d398
("genirq: Warn when IRQ_NOAUTOEN is used with shared interrupts") and
kernel now throws a warn dump. But OMAP DWC3 driver uses this flag. As
per commit 12a7f17fac ("usb: dwc3: omap: fix race of pm runtime with
irq handler in probe") that introduced this flag, PM runtime can race
with IRQ handler when deferred probing happens due to extcon,
therefore IRQ_NOAUTOEN needs to be set so that irq is not enabled until
extcon is registered.
Remove setting of IRQ_NOAUTOEN and move the registration of
shared irq to a point after dwc3_omap_extcon_register() and
of_platform_populate(). This avoids possibility of probe deferring and
above said race condition.
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
commit f54edb539c ("usb: dwc3: core: initialize ULPI before trying to
get the PHY") moved call to dwc3_core_get_phy() from dwc3_probe() to
dwc3_core_init() after dwc3_core_soft_reset(). But
dwc3_core_soft_reset() calls phy_init(), therefore dwc3_core_get_phy()
needs to be called before dwc3_core_soft_reset().
Fix this by moving call to dwc3_core_get_phy() before
dwc3_core_soft_reset().
This fixes the following abort seen on DRA7xx platforms
[ 24.769118] usb usb2: SerialNumber: xhci-hcd.1.auto
[ 24.781144] hub 2-0:1.0: USB hub found
[ 24.787836] hub 2-0:1.0: 1 port detected
[ 24.809939] Unhandled fault: imprecise external abort (0x1406) at 0x00000000
Reported-by: Carlos Hernandez <ceh@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Make the code like the rest of the kernel.
Also use inline instead of __inline__.
Link: http://lkml.kernel.org/r/a5072b74b6c293e6ec93c4900482e9d3267f15b2.1499284835.git.joe@perches.com
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here are some remaining USB fixes for 4.13-rc1. They were originally
scheduled for 4.12-final, but I didn't send them to you in time.
Because of that, they were in a separate branch from the larger USB set
of patches, so here they are in a separate pull request.
Nothing major here a all, just 3 small patches:
- some usb-serial new device ids
- xhci bugfix for some crazy AMD hardware
All of these have been in linux-next for a long time with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWV9FRg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylHxgCfTT31v4FaxH2k76qA1ZnHdXWHqyQAn3oyOE4T
uJhpp1FbFR1VNXM/jRox
=PCPm
-----END PGP SIGNATURE-----
Merge tag 'usb-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some remaining USB fixes for 4.13-rc1. They were originally
scheduled for 4.12-final, but I didn't send them to you in time.
Because of that, they were in a separate branch from the larger USB
set of patches, so here they are in a separate pull request.
Nothing major here a all, just three small patches:
- some usb-serial new device ids
- xhci bugfix for some crazy AMD hardware
All of these have been in linux-next for a long time with no reported
issues"
* tag 'usb-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
xhci: Limit USB2 port wake support for AMD Promontory hosts
USB: serial: qcserial: new Sierra Wireless EM7305 device ID
USB: serial: option: add two Longcheer device ids
Pull MFD updates from Lee Jones:
"New Drivers:
- Intel Cherry Trail Whiskey Cove PMIC
- TI LP87565 PMIC
New Device Support:
- Add support for Cannonlake to intel-lpss-pci
- Add support for Simatic IOT2000 to intel_quark_i2c_gpio
New Functionality:
- Add Regulator support (axp20x)
Fix-ups:
- Rework IRQ handling (intel_soc_pmic_bxtwc, rtsx_pcr, cros_ec)
- Remove unused/unwelcome code (ipaq-micro, wm831x-core, da9062-core)
- Provide deregistration on unbind (rn5t618)
- Rework DT code/documentation (arizona)
- Constify things (fsl-imx25-tsadc)
- MAINTAINERS updates (DA9062/61)
- Kconfig configuration adaptions (INTEL_SOC_PMIC, MFD_AXP20X_I2C)
- Switch to DMI matching (intel_quark_i2c_gpio)
- Provide an appropriate level of error checking (wm831x-{i2c,spi},
twl4030-irq, tc6393xb)
- Make use of devm_* (resource handling) calls (intel_soc_pmic_bxtwc,
stm32-timers, atmel-flexcom, cros_ec, fsl-imx25-tsadc,
exynos-lpass, palmas, qcom-spmi-pmic, smsc-ece1099,
motorola-cpcap)"
[ Skipped the last commit in that series that added eight thousand
lines of pointless repeated register definitions. - Linus ]
* tag 'mfd-next-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (38 commits)
mfd: Add LP87565 PMIC support
mfd: cros_ec: Free IRQ on exit
dt-bindings: vendor-prefixes: Add arctic to vendor prefix
mfd: da9061: Fix to remove BBAT_CONT register from chip model
mfd: da9061: Fix to remove BBAT_CONT register from chip model
mfd: axp20x-i2c: Document that this must be builtin on x86
mfd: Add Cherry Trail Whiskey Cove PMIC driver
mfd: tc6393xb: Handle return value of clk_prepare_enable
mfd: intel_quark_i2c_gpio: Add support for SIMATIC IOT2000 platform
mfd: intel_quark_i2c_gpio: Use dmi_system_id table for retrieving frequency
mfd: motorola-cpcap: Use devm_of_platform_populate()
mfd: smsc-ece: Use devm_of_platform_populate()
mfd: qcom-spmi-pmic: Use devm_of_platform_populate()
mfd: palmas: Use devm_of_platform_populate()
mfd: exynos: Use devm_of_platform_populate()
mfd: fsl-imx25: Use devm_of_platform_populate()
mfd: cros_ec: Use devm_of_platform_populate()
mfd: atmel: Use devm_of_platform_populate()
mfd: stm32-timers: Use devm_of_platform_populate()
mfd: intel_soc_pmic: Select designware i2c-bus driver
...
Pull misc compat stuff updates from Al Viro:
"This part is basically untangling various compat stuff. Compat
syscalls moved to their native counterparts, getting rid of quite a
bit of double-copying and/or set_fs() uses. A lot of field-by-field
copyin/copyout killed off.
- kernel/compat.c is much closer to containing just the
copyin/copyout of compat structs. Not all compat syscalls are gone
from it yet, but it's getting there.
- ipc/compat_mq.c killed off completely.
- block/compat_ioctl.c cleaned up; floppy compat ioctls moved to
drivers/block/floppy.c where they belong. Yes, there are several
drivers that implement some of the same ioctls. Some are m68k and
one is 32bit-only pmac. drivers/block/floppy.c is the only one in
that bunch that can be built on biarch"
* 'misc.compat' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
mqueue: move compat syscalls to native ones
usbdevfs: get rid of field-by-field copyin
compat_hdio_ioctl: get rid of set_fs()
take floppy compat ioctls to sodding floppy.c
ipmi: get rid of field-by-field __get_user()
ipmi: get COMPAT_IPMICTL_RECEIVE_MSG in sync with the native one
rt_sigtimedwait(): move compat to native
select: switch compat_{get,put}_fd_set() to compat_{get,put}_bitmap()
put_compat_rusage(): switch to copy_to_user()
sigpending(): move compat to native
getrlimit()/setrlimit(): move compat to native
times(2): move compat to native
compat_{get,put}_bitmap(): use unsafe_{get,put}_user()
fb_get_fscreeninfo(): don't bother with do_fb_ioctl()
do_sigaltstack(): lift copying to/from userland into callers
take compat_sys_old_getrlimit() to native syscall
trim __ARCH_WANT_SYS_OLD_GETRLIMIT
This development cycle resulted in a fair amount of changes in both
core and driver sides. The most significant change in ALSA core is
about PCM. Also the support of of-graph card and the new DAPM widget
for DSP are noteworthy changes in ASoC core. And there're lots of
small changes splat over the tree, as you can see in diffstat.
Below are a few highlights:
ALSA core:
- Removal of set_fs() hackery from PCM core stuff, and the code
reorganization / optimization thereafter
- Improved support of PCM ack ops, and a new ABI for improved
control/status mmap handling
- Lots of constifications in various codes
ASoC core:
- The support of of-graph card, which may work as a better generic
device for a replacement of simple-card
- New widget types intended mainly for use with DSPs
ASoC drivers:
- New drivers for Allwinner V3s SoCs
- Ensonic ES8316 codec support
- More Intel SKL and KBL works
- More device support for Intel SST Atom (mostly for cheap tablets and
2-in-1 devices)
- Support for Rockchip PDM controllers
- Support for STM32 I2S and S/PDIF controllers
- Support for ZTE AUD96P22 codecs
HD-audio:
- Support of new Realtek codecs (ALC215/ALC285/ALC289), more quirks
for HP and Dell machines
- A few more fixes for i915 component binding
Note that of-graph change may bring the conflicts with a later pull
request of devicetree, as currently found in linux-next.
-----BEGIN PGP SIGNATURE-----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=PUEh
-----END PGP SIGNATURE-----
Merge tag 'sound-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This development cycle resulted in a fair amount of changes in both
core and driver sides. The most significant change in ALSA core is
about PCM. Also the support of of-graph card and the new DAPM widget
for DSP are noteworthy changes in ASoC core. And there're lots of
small changes splat over the tree, as you can see in diffstat.
Below are a few highlights:
ALSA core:
- Removal of set_fs() hackery from PCM core stuff, and the code
reorganization / optimization thereafter
- Improved support of PCM ack ops, and a new ABI for improved
control/status mmap handling
- Lots of constifications in various codes
ASoC core:
- The support of of-graph card, which may work as a better generic
device for a replacement of simple-card
- New widget types intended mainly for use with DSPs
ASoC drivers:
- New drivers for Allwinner V3s SoCs
- Ensonic ES8316 codec support
- More Intel SKL and KBL works
- More device support for Intel SST Atom (mostly for cheap tablets
and 2-in-1 devices)
- Support for Rockchip PDM controllers
- Support for STM32 I2S and S/PDIF controllers
- Support for ZTE AUD96P22 codecs
HD-audio:
- Support of new Realtek codecs (ALC215/ALC285/ALC289), more quirks
for HP and Dell machines
- A few more fixes for i915 component binding"
* tag 'sound-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (418 commits)
ALSA: hda - Fix unbalance of i915 module refcount
ASoC: Intel: Skylake: Remove driver debugfs exit
ASoC: Intel: Skylake: explicitly add the headers sst-dsp.h
ALSA: hda/realtek - Remove GPIO_MASK
ALSA: hda/realtek - Fix typo of pincfg for Dell quirk
ALSA: pcm: add a documentation for tracepoints
ALSA: atmel: ac97c: fix error return code in atmel_ac97c_probe()
ALSA: x86: fix error return code in hdmi_lpe_audio_probe()
ASoC: Intel: Skylake: Add support to read firmware registers
ASoC: Intel: Skylake: Add sram address to sst_addr structure
ASoC: Intel: Skylake: Debugfs facility to dump module config
ASoC: Intel: Skylake: Add debugfs support
ASoC: fix semicolon.cocci warnings
ASoC: rt5645: Add quirk override by module option
ASoC: rsnd: make arrays path and cmd_case static const
ASoC: audio-graph-card: add widgets and routing for external amplifier support
ASoC: audio-graph-card: update bindings for amplifier support
ASoC: rt5665: calibration should be done before jack detection
ASoC: rsnd: constify dev_pm_ops structures.
ASoC: nau8825: change crosstalk-bypass property to bool type
...
Pull networking updates from David Miller:
"Reasonably busy this cycle, but perhaps not as busy as in the 4.12
merge window:
1) Several optimizations for UDP processing under high load from
Paolo Abeni.
2) Support pacing internally in TCP when using the sch_fq packet
scheduler for this is not practical. From Eric Dumazet.
3) Support mutliple filter chains per qdisc, from Jiri Pirko.
4) Move to 1ms TCP timestamp clock, from Eric Dumazet.
5) Add batch dequeueing to vhost_net, from Jason Wang.
6) Flesh out more completely SCTP checksum offload support, from
Davide Caratti.
7) More plumbing of extended netlink ACKs, from David Ahern, Pablo
Neira Ayuso, and Matthias Schiffer.
8) Add devlink support to nfp driver, from Simon Horman.
9) Add RTM_F_FIB_MATCH flag to RTM_GETROUTE queries, from Roopa
Prabhu.
10) Add stack depth tracking to BPF verifier and use this information
in the various eBPF JITs. From Alexei Starovoitov.
11) Support XDP on qed device VFs, from Yuval Mintz.
12) Introduce BPF PROG ID for better introspection of installed BPF
programs. From Martin KaFai Lau.
13) Add bpf_set_hash helper for TC bpf programs, from Daniel Borkmann.
14) For loads, allow narrower accesses in bpf verifier checking, from
Yonghong Song.
15) Support MIPS in the BPF selftests and samples infrastructure, the
MIPS eBPF JIT will be merged in via the MIPS GIT tree. From David
Daney.
16) Support kernel based TLS, from Dave Watson and others.
17) Remove completely DST garbage collection, from Wei Wang.
18) Allow installing TCP MD5 rules using prefixes, from Ivan
Delalande.
19) Add XDP support to Intel i40e driver, from Björn Töpel
20) Add support for TC flower offload in nfp driver, from Simon
Horman, Pieter Jansen van Vuuren, Benjamin LaHaise, Jakub
Kicinski, and Bert van Leeuwen.
21) IPSEC offloading support in mlx5, from Ilan Tayari.
22) Add HW PTP support to macb driver, from Rafal Ozieblo.
23) Networking refcount_t conversions, From Elena Reshetova.
24) Add sock_ops support to BPF, from Lawrence Brako. This is useful
for tuning the TCP sockopt settings of a group of applications,
currently via CGROUPs"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1899 commits)
net: phy: dp83867: add workaround for incorrect RX_CTRL pin strap
dt-bindings: phy: dp83867: provide a workaround for incorrect RX_CTRL pin strap
cxgb4: Support for get_ts_info ethtool method
cxgb4: Add PTP Hardware Clock (PHC) support
cxgb4: time stamping interface for PTP
nfp: default to chained metadata prepend format
nfp: remove legacy MAC address lookup
nfp: improve order of interfaces in breakout mode
net: macb: remove extraneous return when MACB_EXT_DESC is defined
bpf: add missing break in for the TCP_BPF_SNDCWND_CLAMP case
bpf: fix return in load_bpf_file
mpls: fix rtm policy in mpls_getroute
net, ax25: convert ax25_cb.refcount from atomic_t to refcount_t
net, ax25: convert ax25_route.refcount from atomic_t to refcount_t
net, ax25: convert ax25_uid_assoc.refcount from atomic_t to refcount_t
net, sctp: convert sctp_ep_common.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_transport.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_chunk.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_datamsg.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_auth_bytes.refcnt from atomic_t to refcount_t
...
- Rework suspend-to-idle to allow it to take wakeup events signaled
by the EC into account on ACPI-based platforms in order to properly
support power button wakeup from suspend-to-idle on recent Dell
laptops (Rafael Wysocki).
That includes the core suspend-to-idle code rework, support for
the Low Power S0 _DSM interface, and support for the ACPI INT0002
Virtual GPIO device from Hans de Goede (required for USB keyboard
wakeup from suspend-to-idle to work on some machines).
- Stop trying to export the current CPU frequency via /proc/cpuinfo
on x86 as that is inaccurate and confusing (Len Brown).
- Rework the way in which the current CPU frequency is exported by
the kernel (over the cpufreq sysfs interface) on x86 systems with
the APERF and MPERF registers by always using values read from
these registers, when available, to compute the current frequency
regardless of which cpufreq driver is in use (Len Brown).
- Rework the PCI/ACPI device wakeup infrastructure to remove the
questionable and artificial distinction between "devices that
can wake up the system from sleep states" and "devices that can
generate wakeup signals in the working state" from it, which
allows the code to be simplified quite a bit (Rafael Wysocki).
- Fix the wakeup IRQ framework by making it use SRCU instead of
RCU which doesn't allow sleeping in the read-side critical
sections, but which in turn is expected to be allowed by the
IRQ bus locking infrastructure (Thomas Gleixner).
- Modify some computations in the intel_pstate driver to avoid
rounding errors resulting from them (Srinivas Pandruvada).
- Reduce the overhead of the intel_pstate driver in the HWP
(hardware-managed P-states) mode and when the "performance"
P-state selection algorithm is in use by making it avoid
registering scheduler callbacks in those cases (Len Brown).
- Rework the energy_performance_preference sysfs knob in
intel_pstate by changing the values that correspond to
different symbolic hint names used by it (Len Brown).
- Make it possible to use more than one cpuidle driver at the same
time on ARM (Daniel Lezcano).
- Make it possible to prevent the cpuidle menu governor from using
the 0 state by disabling it via sysfs (Nicholas Piggin).
- Add support for FFH (Fixed Functional Hardware) MWAIT in ACPI C1
on AMD systems (Yazen Ghannam).
- Make the CPPC cpufreq driver take the lowest nonlinear performance
information into account (Prashanth Prakash).
- Add support for hi3660 to the cpufreq-dt driver, fix the
imx6q driver and clean up the sfi, exynos5440 and intel_pstate
drivers (Colin Ian King, Krzysztof Kozlowski, Octavian Purdila,
Rafael Wysocki, Tao Wang).
- Fix a few minor issues in the generic power domains (genpd)
framework and clean it up somewhat (Krzysztof Kozlowski,
Mikko Perttunen, Viresh Kumar).
- Fix a couple of minor issues in the operating performance points
(OPP) framework and clean it up somewhat (Viresh Kumar).
- Fix a CONFIG dependency in the hibernation core and clean it up
slightly (Balbir Singh, Arvind Yadav, BaoJun Luo).
- Add rk3228 support to the rockchip-io adaptive voltage scaling
(AVS) driver (David Wu).
- Fix an incorrect bit shift operation in the RAPL power capping
driver (Adam Lessnau).
- Add support for the EPP field in the HWP (hardware managed
P-states) control register, HWP.EPP, to the x86_energy_perf_policy
tool and update msr-index.h with HWP.EPP values (Len Brown).
- Fix some minor issues in the turbostat tool (Len Brown).
- Add support for AMD family 0x17 CPUs to the cpupower tool and fix
a minor issue in it (Sherry Hurwitz).
- Assorted cleanups, mostly related to the constification of some
data structures (Arvind Yadav, Joe Perches, Kees Cook, Krzysztof
Kozlowski).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Wsph
-----END PGP SIGNATURE-----
Merge tag 'pm-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"The big ticket items here are the rework of suspend-to-idle in order
to add proper support for power button wakeup from it on recent Dell
laptops and the rework of interfaces exporting the current CPU
frequency on x86.
In addition to that, support for a few new pieces of hardware is
added, the PCI/ACPI device wakeup infrastructure is simplified
significantly and the wakeup IRQ framework is fixed to unbreak the IRQ
bus locking infrastructure.
Also, there are some functional improvements for intel_pstate, tools
updates and small fixes and cleanups all over.
Specifics:
- Rework suspend-to-idle to allow it to take wakeup events signaled
by the EC into account on ACPI-based platforms in order to properly
support power button wakeup from suspend-to-idle on recent Dell
laptops (Rafael Wysocki).
That includes the core suspend-to-idle code rework, support for the
Low Power S0 _DSM interface, and support for the ACPI INT0002
Virtual GPIO device from Hans de Goede (required for USB keyboard
wakeup from suspend-to-idle to work on some machines).
- Stop trying to export the current CPU frequency via /proc/cpuinfo
on x86 as that is inaccurate and confusing (Len Brown).
- Rework the way in which the current CPU frequency is exported by
the kernel (over the cpufreq sysfs interface) on x86 systems with
the APERF and MPERF registers by always using values read from
these registers, when available, to compute the current frequency
regardless of which cpufreq driver is in use (Len Brown).
- Rework the PCI/ACPI device wakeup infrastructure to remove the
questionable and artificial distinction between "devices that can
wake up the system from sleep states" and "devices that can
generate wakeup signals in the working state" from it, which allows
the code to be simplified quite a bit (Rafael Wysocki).
- Fix the wakeup IRQ framework by making it use SRCU instead of RCU
which doesn't allow sleeping in the read-side critical sections,
but which in turn is expected to be allowed by the IRQ bus locking
infrastructure (Thomas Gleixner).
- Modify some computations in the intel_pstate driver to avoid
rounding errors resulting from them (Srinivas Pandruvada).
- Reduce the overhead of the intel_pstate driver in the HWP
(hardware-managed P-states) mode and when the "performance" P-state
selection algorithm is in use by making it avoid registering
scheduler callbacks in those cases (Len Brown).
- Rework the energy_performance_preference sysfs knob in intel_pstate
by changing the values that correspond to different symbolic hint
names used by it (Len Brown).
- Make it possible to use more than one cpuidle driver at the same
time on ARM (Daniel Lezcano).
- Make it possible to prevent the cpuidle menu governor from using
the 0 state by disabling it via sysfs (Nicholas Piggin).
- Add support for FFH (Fixed Functional Hardware) MWAIT in ACPI C1 on
AMD systems (Yazen Ghannam).
- Make the CPPC cpufreq driver take the lowest nonlinear performance
information into account (Prashanth Prakash).
- Add support for hi3660 to the cpufreq-dt driver, fix the imx6q
driver and clean up the sfi, exynos5440 and intel_pstate drivers
(Colin Ian King, Krzysztof Kozlowski, Octavian Purdila, Rafael
Wysocki, Tao Wang).
- Fix a few minor issues in the generic power domains (genpd)
framework and clean it up somewhat (Krzysztof Kozlowski, Mikko
Perttunen, Viresh Kumar).
- Fix a couple of minor issues in the operating performance points
(OPP) framework and clean it up somewhat (Viresh Kumar).
- Fix a CONFIG dependency in the hibernation core and clean it up
slightly (Balbir Singh, Arvind Yadav, BaoJun Luo).
- Add rk3228 support to the rockchip-io adaptive voltage scaling
(AVS) driver (David Wu).
- Fix an incorrect bit shift operation in the RAPL power capping
driver (Adam Lessnau).
- Add support for the EPP field in the HWP (hardware managed
P-states) control register, HWP.EPP, to the x86_energy_perf_policy
tool and update msr-index.h with HWP.EPP values (Len Brown).
- Fix some minor issues in the turbostat tool (Len Brown).
- Add support for AMD family 0x17 CPUs to the cpupower tool and fix a
minor issue in it (Sherry Hurwitz).
- Assorted cleanups, mostly related to the constification of some
data structures (Arvind Yadav, Joe Perches, Kees Cook, Krzysztof
Kozlowski)"
* tag 'pm-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (69 commits)
cpufreq: Update scaling_cur_freq documentation
cpufreq: intel_pstate: Clean up after performance governor changes
PM: hibernate: constify attribute_group structures.
cpuidle: menu: allow state 0 to be disabled
intel_idle: Use more common logging style
PM / Domains: Fix missing default_power_down_ok comment
PM / Domains: Fix unsafe iteration over modified list of domains
PM / Domains: Fix unsafe iteration over modified list of domain providers
PM / Domains: Fix unsafe iteration over modified list of device links
PM / Domains: Handle safely genpd_syscore_switch() call on non-genpd device
PM / Domains: Call driver's noirq callbacks
PM / core: Drop run_wake flag from struct dev_pm_info
PCI / PM: Simplify device wakeup settings code
PCI / PM: Drop pme_interrupt flag from struct pci_dev
ACPI / PM: Consolidate device wakeup settings code
ACPI / PM: Drop run_wake from struct acpi_device_wakeup_flags
PM / QoS: constify *_attribute_group.
PM / AVS: rockchip-io: add io selectors and supplies for rk3228
powercap/RAPL: prevent overridding bits outside of the mask
PM / sysfs: Constify attribute groups
...
Here is the big driver core update for 4.13-rc1.
The large majority of this is a lot of cleanup of old fields in the
driver core structures and their remaining usages in random drivers.
All of those fixes have been reviewed by the various subsystem
maintainers. There's also some small firmware updates in here, a new
kobject uevent api interface that makes userspace interaction easier,
and a few other minor things.
All of these have been in linux-next for a long while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWVpX4A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymobgCfd0d13IfpZoq1N41wc6z2Z0xD7cwAnRMeH1/p
kEeISGpHPYP9f8PBh9FO
=Hfqt
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big driver core update for 4.13-rc1.
The large majority of this is a lot of cleanup of old fields in the
driver core structures and their remaining usages in random drivers.
All of those fixes have been reviewed by the various subsystem
maintainers. There's also some small firmware updates in here, a new
kobject uevent api interface that makes userspace interaction easier,
and a few other minor things.
All of these have been in linux-next for a long while with no reported
issues"
* tag 'driver-core-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (56 commits)
arm: mach-rpc: ecard: fix build error
zram: convert remaining CLASS_ATTR() to CLASS_ATTR_RO()
driver-core: remove struct bus_type.dev_attrs
powerpc: vio_cmo: use dev_groups and not dev_attrs for bus_type
powerpc: vio: use dev_groups and not dev_attrs for bus_type
USB: usbip: convert to use DRIVER_ATTR_RW
s390: drivers: convert to use DRIVER_ATTR_RO/WO
platform: thinkpad_acpi: convert to use DRIVER_ATTR_RO/RW
pcmcia: ds: convert to use DRIVER_ATTR_RO
wireless: ipw2x00: convert to use DRIVER_ATTR_RW
net: ehea: convert to use DRIVER_ATTR_RO
net: caif: convert to use DRIVER_ATTR_RO
TTY: hvc: convert to use DRIVER_ATTR_RW
PCI: pci-driver: convert to use DRIVER_ATTR_WO
IB: nes: convert to use DRIVER_ATTR_RW
HID: hid-core: convert to use DRIVER_ATTR_RO and drv_groups
arm: ecard: fix dev_groups patch typo
tty: serdev: use dev_groups and not dev_attrs for bus_type
sparc: vio: use dev_groups and not dev_attrs for bus_type
hid: intel-ish-hid: use dev_groups and not dev_attrs for bus_type
...
Here is the large tty/serial patchset for 4.13-rc1.
A lot of tty and serial driver updates are in here, along with some
fixups for some __get/put_user usages that were reported. Nothing huge,
just lots of development by a number of different developers, full
details in the shortlog.
All of these have been in linux-next for a while. There will be a merge
issue with the arm-soc tree in the include/linux/platform_data/atmel.h
file. Stephen has sent out a fixup for it, so it shouldn't be that
difficult to merge.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWVpZ9w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylkTgCfV2HhbxIph/aEL1nJmwW64oCXFrMAoK59ZH65
tBZIosv0d91K1A+mObBT
=adPL
-----END PGP SIGNATURE-----
Merge tag 'tty-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the large tty/serial patchset for 4.13-rc1.
A lot of tty and serial driver updates are in here, along with some
fixups for some __get/put_user usages that were reported. Nothing
huge, just lots of development by a number of different developers,
full details in the shortlog.
All of these have been in linux-next for a while"
* tag 'tty-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (71 commits)
tty: serial: lpuart: add a more accurate baud rate calculation method
tty: serial: lpuart: add earlycon support for imx7ulp
tty: serial: lpuart: add imx7ulp support
dt-bindings: serial: fsl-lpuart: add i.MX7ULP support
tty: serial: lpuart: add little endian 32 bit register support
tty: serial: lpuart: refactor lpuart32_{read|write} prototype
tty: serial: lpuart: introduce lpuart_soc_data to represent SoC property
serial: imx-serial - move DMA buffer configuration to DT
serial: imx: Enable RTSD only when needed
serial: imx: Remove unused members from imx_port struct
serial: 8250: 8250_omap: Fix race b/w dma completion and RX timeout
serial: 8250: Fix THRE flag usage for CAP_MINI
tty/serial: meson_uart: update to stable bindings
dt-bindings: serial: Add bindings for the Amlogic Meson UARTs
serial: Delete dead code for CIR serial ports
serial: sirf: make of_device_ids const
serial/mpsc: switch to dma_alloc_attrs
tty: serial: Add Actions Semi Owl UART earlycon
dt-bindings: serial: Document Actions Semi Owl UARTs
tty/serial: atmel: make the driver DT only
...
Here is the big patchset of USB and PHY driver updates for 4.13-rc1.
On the PHY side, they decided to move files around to "make things
easier" in their tree. Hopefully that wasn't a mistake, but in
linux-next testing, we haven't had any reported problems.
There's the usual set of gadget and xhci and musb updates in here as
well, along with a number of smaller updates for a raft of different USB
drivers. Full details in the shortlog, nothing really major.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWVpavQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymJrgCgp8Pso8bs+bnIknUSQFSguWd3wM0AnA8X3NHf
lrdCuqw+2oxGOQrecacz
=5L4Q
-----END PGP SIGNATURE-----
Merge tag 'usb-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big patchset of USB and PHY driver updates for 4.13-rc1.
On the PHY side, they decided to move files around to "make things
easier" in their tree. Hopefully that wasn't a mistake, but in
linux-next testing, we haven't had any reported problems.
There's the usual set of gadget and xhci and musb updates in here as
well, along with a number of smaller updates for a raft of different
USB drivers. Full details in the shortlog, nothing really major.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (173 commits)
Add USB quirk for HVR-950q to avoid intermittent device resets
USB hub_probe: rework ugly goto-into-compound-statement
usb: host: ohci-pxa27x: Handle return value of clk_prepare_enable
USB: serial: cp210x: add ID for CEL EM3588 USB ZigBee stick
usbip: Fix uninitialized variable bug in vhci
usb: core: read USB ports from DT in the usbport LED trigger driver
dt-bindings: leds: document new trigger-sources property
usb: typec: ucsi: Add ACPI driver
usb: typec: Add support for UCSI interface
usb: musb: compress return logic into one line
USB: serial: propagate late probe errors
USB: serial: refactor port endpoint setup
usb: musb: tusb6010_omap: Convert to DMAengine API
ARM: OMAP2+: DMA: Add slave map entries for 24xx external request lines
usb: musb: tusb6010: Handle DMA TX completion in DMA callback as well
usb: musb: tusb6010_omap: Allocate DMA channels upfront
usb: musb: tusb6010_omap: Create new struct for DMA data/parameters
usb: musb: tusb6010_omap: Use one musb_ep_select call in tusb_omap_dma_program
usb: musb: tusb6010: Add MUSB_G_NO_SKB_RESERVE to quirks
usb: musb: Add quirk to avoid skb reserve in gadget mode
...
The big news with this release is the of-graph card, this provides a
replacement for simple-card that is much more flexibile and scalable,
allowing many more systems to use a generic sound card than was possible
before:
- The of-graph card, finally merged after a long and dedicated effort
by Morimoto-san.
- New widget types intended mainly for use with DSPs.
- New drivers for Allwinner V3s SoCs, Ensonic ES8316, several classes
of x86 machine, Rockchip PDM controllers, STM32 I2S and S/PDIF
controllers and ZTE AUD96P22 CODECs.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAllaa7wTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0MhRB/0cIuUi/SmMSGz7cNKdDDArdpxHUV0U
dJb6qqhXCKeDQcx/34b1m+BnZpeT9au4Nt8HxOlLRbumcnuesYqfeBeZvuJhsC4I
q3e8e+idQlOp3+WM+snUXhWM4P/UsA9H4BaV1jvYSQW/C9WhfuLxsOraRiebLH7u
WJkmfeVjpzHHWzfDtpWJLHVroRLLMbOaz0e0Pw8/R1dfof0u27zKknqHOUcwRg0N
4+IWvKn3p59VE6eM6QUmruMZZCCfn2Hv5RygWf3LaHVlhA28BZi0dyMMSSSzVG6o
Im1Wm5z0dmmTfQKdNDU3PPBEKG6amTqF+2uuXOsq1I7vuiT+akHZbgWW
=F5BP
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v4.13
The big news with this release is the of-graph card, this provides a
replacement for simple-card that is much more flexibile and scalable,
allowing many more systems to use a generic sound card than was possible
before:
- The of-graph card, finally merged after a long and dedicated effort
by Morimoto-san.
- New widget types intended mainly for use with DSPs.
- New drivers for Allwinner V3s SoCs, Ensonic ES8316, several classes
of x86 machine, Rockchip PDM controllers, STM32 I2S and S/PDIF
controllers and ZTE AUD96P22 CODECs.
- introduce the new uuid_t/guid_t types that are going to replace
the somewhat confusing uuid_be/uuid_le types and make the terminology
fit the various specs, as well as the userspace libuuid library.
(me, based on a previous version from Amir)
- consolidated generic uuid/guid helper functions lifted from XFS
and libnvdimm (Amir and me)
- conversions to the new types and helpers (Amir, Andy and me)
-----BEGIN PGP SIGNATURE-----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=J/4P
-----END PGP SIGNATURE-----
Merge tag 'uuid-for-4.13' of git://git.infradead.org/users/hch/uuid
Pull uuid subsystem from Christoph Hellwig:
"This is the new uuid subsystem, in which Amir, Andy and I have started
consolidating our uuid/guid helpers and improving the types used for
them. Note that various other subsystems have pulled in this tree, so
I'd like it to go in early.
UUID/GUID summary:
- introduce the new uuid_t/guid_t types that are going to replace the
somewhat confusing uuid_be/uuid_le types and make the terminology
fit the various specs, as well as the userspace libuuid library.
(me, based on a previous version from Amir)
- consolidated generic uuid/guid helper functions lifted from XFS and
libnvdimm (Amir and me)
- conversions to the new types and helpers (Amir, Andy and me)"
* tag 'uuid-for-4.13' of git://git.infradead.org/users/hch/uuid: (34 commits)
ACPI: hns_dsaf_acpi_dsm_guid can be static
mmc: sdhci-pci: make guid intel_dsm_guid static
uuid: Take const on input of uuid_is_null() and guid_is_null()
thermal: int340x_thermal: fix compile after the UUID API switch
thermal: int340x_thermal: Switch to use new generic UUID API
acpi: always include uuid.h
ACPI: Switch to use generic guid_t in acpi_evaluate_dsm()
ACPI / extlog: Switch to use new generic UUID API
ACPI / bus: Switch to use new generic UUID API
ACPI / APEI: Switch to use new generic UUID API
acpi, nfit: Switch to use new generic UUID API
MAINTAINERS: add uuid entry
tmpfs: generate random sb->s_uuid
scsi_debug: switch to uuid_t
nvme: switch to uuid_t
sysctl: switch to use uuid_t
partitions/ldm: switch to use uuid_t
overlayfs: use uuid_t instead of uuid_be
fs: switch ->s_uuid to uuid_t
ima/policy: switch to use uuid_t
...
* acpi-pm:
PM / core: Drop run_wake flag from struct dev_pm_info
PCI / PM: Simplify device wakeup settings code
PCI / PM: Drop pme_interrupt flag from struct pci_dev
ACPI / PM: Consolidate device wakeup settings code
ACPI / PM: Drop run_wake from struct acpi_device_wakeup_flags
ACPI / sleep: EC-based wakeup from suspend-to-idle on recent systems
platform: x86: intel-hid: Wake up the system from suspend-to-idle
platform: x86: intel-vbtn: Wake up the system from suspend-to-idle
ACPI / PM: Ignore spurious SCI wakeups from suspend-to-idle
platform/x86: Add driver for ACPI INT0002 Virtual GPIO device
PCI / PM: Restore PME Enable if skipping wakeup setup
PM / sleep: Print timing information if debug is enabled
ACPI / PM: Clean up device wakeup enable/disable code
ACPI / PM: Change log level of wakeup-related message
USB / PCI / PM: Allow the PCI core to do the resume cleanup
ACPI / PM: Run wakeup notify handlers synchronously
Conflicts:
drivers/base/power/main.c
The USB core and sysfs will attempt to enumerate certain parameters
which are unsupported by the au0828 - causing inconsistent behavior
and sometimes causing the chip to reset. Avoid making these calls.
This problem manifested as intermittent cases where the au8522 would
be reset on analog video startup, in particular when starting up ALSA
audio streaming in parallel - the sysfs entries created by
snd-usb-audio on streaming startup would result in unsupported control
messages being sent during tuning which would put the chip into an
unknown state.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rework smelling code (goto inside compound statement). Perhaps this is
legacy. Anyway such code is not appropriate for Linux kernel.
Signed-off-by: Eugene Korenevsky <ekorenevsky@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added the USB serial device ID for the CEL ZigBee EM3588
radio stick.
Signed-off-by: Jeremie Rapin <rapinj@gmail.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the USB-serial updates for 4.13, including support for
manipulating the modem-control signals of qcserial devices, propagation
of errnos after late probe errors from usb-serial core, and a couple of
clean ups.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEHszNKQClByu0A+9RQQ3kT97htJUFAllTZSARHGpvaGFuQGtl
cm5lbC5vcmcACgkQQQ3kT97htJWM+A//U7WSk6Y0iFdT9lw6EWg55BsybGv3HZ1O
2UA3y2P1TEWlsD+hBZs/4TRnay6udxc/zgIs2dDL7jPLw3ZNZCp8hIqtMjiLZA8i
Ca4KgQlDkPEHps7rn1fbiZAsgFI25Y0+Bs3fzz+JDW+jV9jkWGQ1jpBoFOHgIc6v
LbiWZOyLFWoF59BzFeys0PW1ar4Yl5BRKIlztkJOu7NVKwvp7SEQeyIyhplKWDP1
egvptlGRIy1vDJMFMz5PYCyt4jFFgdDKp1ffXHEKAbcBRgiZbvjGrVRE3RePskN9
Ui/SI0a6+DAfbJxSXovpdoOVvQqYKzm6QuneROXDpKYoPSLe7/31XJxM7U8gO0+J
dju6EANUncVrzCeThyTfaa38FT8/eInUuygQzr0mwrouDxQRMPWsePX+o2T4k04U
5PZ2IBx/PpAss4GNPL5gx9PJSxd8fnQVmRCAgsxFAZn4N8o1NXh7rpHby0D0X2GZ
5iaKhuYCT0pxxv6ueey4HnLlxEcmhQBdur0AIEK6iaUG24mIHiSu5V5JxDNHIyYX
LECv8HpLVi1htaO8khlSNOZ5zTsaa21c7GRXKLrdHiy7XKF/TPTNgky6Wqdr/X+8
rRxYp5fC1DXOvjXJZlArnNbG2fbIgxeIFbJI/qjTut2fUyLlIN7vwn5zTKOyqaRT
CJOSP039aJg=
=1HgT
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.13-rc1
Here are the USB-serial updates for 4.13, including support for
manipulating the modem-control signals of qcserial devices, propagation
of errnos after late probe errors from usb-serial core, and a couple of
clean ups.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
The run_wake flag in struct dev_pm_info is used to indicate whether
or not the device is capable of generating remote wakeup signals at
run time (or in the system working state), but the distinction
between runtime remote wakeup and system wakeup signaling has always
been rather artificial. The only practical reason for it to exist
at the core level was that ACPI and PCI treated those two cases
differently, but that's not the case any more after recent changes.
For this reason, get rid of the run_wake flag and, when applicable,
use device_set_wakeup_capable() and device_can_wakeup() instead of
device_set_run_wake() and device_run_wake(), respectively.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
The patch 03cd00d538: "usbip: vhci-hcd: Set the vhci structure up
to work" introduced a bug which uses a vairable without initialization
in error handling code. Fix it.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Yuyang Du <yuyang.du@intel.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This uses DT info to read relation description of LEDs and USB ports. If
DT has properly described LEDs, trigger will know when to turn them on.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UCSI - USB Type-C Connector System Software Interface - is a
specification that defines set of registers and data
structures for controlling the USB Type-C ports. It's
designed for systems where an embedded controller (EC) is in
charge of the USB Type-C PHY or USB Power Delivery
controller. It is designed for systems with EC, but it is
not limited to them, and for example some USB Power Delivery
controllers will use it as their direct control interface.
With UCSI the EC (or USB PD controller) acts as the port
manager, implementing all USB Type-C and Power Delivery state
machines. The OS can use the interfaces for reading the
status of the ports and controlling basic operations like
role swapping.
The UCSI specification highlights the fact that it does not
define the interface method (PCI/I2C/ACPI/etc.).
Therefore the driver is implemented as library and every
supported interface method needs its own driver. Driver for
ACPI is provided in separate patch following this one.
The initial driver includes support for all required
features from UCSI specification version 1.0 (getting
connector capabilities and status, and support for power and
data role swapping), but none of the optional UCSI features
(alternate modes, power source capabilities, and cable
capabilities).
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify return logic to avoid unnecessary variable assignment.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZSdzXAAoJEEhZKYFQ1nG7M1YH/0tSpERwjAaL8xmKjm1KDO9v
EeeTC/P7nkv1iWRdMGZuun8cOivuTD4aC/IuXh6G40FkgUUMZI8qayt+JnS6eiv/
fVbX1L6lP8UnP9C8HHQcANCVlOHysPlbG3hdfpAVjtz56sqdK7NGFakdhHqBerx9
xcD40glwLUpt3jrZfcHPepF9WMn/3eA0GsTXyydHuL/D+jejCUu4kVPICdfOm7Vr
k+E0oilsjfYSxA4NRaqjd5CDpAiPPKQ/g37DIfG13A9bBjvDSQbky4Y69ibVWLqv
sGGCnLeFGx3L798GKeV6bDsKU8NEYF93pnFlQ5FBY5PjYU3mudEXAB/fpVBGagA=
=KEw/
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
One patch to improve error handling at chipidea core
Two entries being added at the same time to the IFLA
policy table, whilst parallel bug fixes to decnet
routing dst handling overlapping with the dst gc removal
in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Propagate errnos for late probe errors (e.g. -ENOMEM on allocation
failures) instead of always returning -EIO.
Note that some drivers are currently returning -ENODEV from their attach
callbacks when a device is not supported, but this has also been mapped
to -EIO.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make the probe callback more readable by refactoring the port
endpoint-resource setup by adding four helper functions.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
With the port_window support in DMAengine and the sDMA driver we can
convert the driver to DMAengine.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handle the DMA TX in a similar way as we do for the RX: in the DMA
completion callback.
Since we are no longer using DMA completion interrupt for the TX we can as
wall keep these interrupts disabled, but keep the handler for debug
purposes.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of requesting the DMA channel in tusb_omap_dma_allocate() do it
when the controller is created and in runtime work from the DMA channel
pool.
This change is needed for the DMAengine conversion of the driver since the
tusb_omap_dma_allocate() is called in interrupt context which might lead
to lock within the DMAengine API when requesting channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For the DMA we have ch (channel), dmareq and sync_dev parameters both
within the tusb_omap_dma_ch and tusb_omap_dma struct.
By creating a common struct the code can be simplified when selecting
between the shared or multichannel DMA parameters.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having one musb_ep_select() instead the two calls in if/else is the same
thing, but makes the code a bit simpler to follow.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using the g_ncm for networking this flag will make sure that the
buffer is aligned to 32bit so the DMA can be used to offload the data
movement.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For tusb6010 the DMA functionality only possible if the buffer is 32bit
aligned (SYNC access to FIFO) since with ASYNC access the TX/RX offset
registers will corrupt eventually.
The MUSB_G_NO_SKB_RESERVE will set the quirk_avoids_skb_reserve flag in
usb_gadget struct to provide correctly aligned buffer.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If dma_request_slave_channel() failed to return a channel,
then the driver will print an error and request to defer probe,
regardless of the cause of the failure.
Defer if the DMA is not ready yet otherwise print an error.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This time around we have a total of 57 non-merge commits. A list of
most important changes follows:
- Improvements to dwc3 tracing interface
- Initial dual-role support for dwc3
- Improvements to how we handle DMA resources in dwc3
- A new f_uac1 implementation which much more flexible
- Removal of AVR32 bits
- Improvements to f_mass_storage driver
-----BEGIN PGP SIGNATURE-----
iQJRBAABCAA7FiEElLzh7wn96CXwjh2IzL64meEamQYFAllHcK0dHGZlbGlwZS5i
YWxiaUBsaW51eC5pbnRlbC5jb20ACgkQzL64meEamQbRQQ//as9W89twbmwOqaSU
pXlbR/gmmEjD6POLWM2GuG3jH8oD3pQq7ZxH22YEFx8Z4wN7vPJ67JJkyoSfhAui
ppnp6AbSPiNolZRb5nTnASnq0cJiTE/rbSM5s1wpe+Qa3ZoQgTHhipnL1/qf8SgR
PN1wgUTGeXxiIA00iOYTG2pjM+OvFO5UpqFJCfh4vuEjcdBWvHDXTUwga5G+qwIa
pgNECcmUsXmHimp6jE+qLUhRYOqvTEC+lc9nzZj4MCru3PDEhZYuOah0XrepiNKU
NB49DVMtDwaGXrKPwa6rNWD8JZF0CAsShvO6V/2p1peInJZUuIrEjXYRUlkPQt9G
yLzxBS+asLCBauzxBFNPrR2BFfJ2uyUCLHYiKP2UbRfWCBFo84MDJCUWACL1aKCH
YLeM1Q7Urxp5suirr2UmwBJdUxXNTncEXsKrtGcrNndKt/Uq8/DxcrbZ2/6ANTDT
wdzm8gSSjtQaFLRc5KgAqrX/ClfEDgQwfgq0DXn9cKxZ9E9xID45s71feKEoBI42
6S/oAopSuBsEmTsPTy0WLR8MTJG3MoJAdr/mHau11Tl0k9qr9KKnHbdUjji9CF6E
aGcV40nKqp9Bd4bcbCNB6NsJUB+zcN7t0bjTsPZQH3XOCSS+fF7oJ6+SIxhsKAFT
rHRl6RhLOIP0vZ0UIsDzeDttCVM=
=v6a5
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-testing
Felipe writes:
usb: changes for v4.13 merge window
This time around we have a total of 57 non-merge commits. A list of
most important changes follows:
- Improvements to dwc3 tracing interface
- Initial dual-role support for dwc3
- Improvements to how we handle DMA resources in dwc3
- A new f_uac1 implementation which much more flexible
- Removal of AVR32 bits
- Improvements to f_mass_storage driver
For AMD Promontory xHCI host, although you can disable USB 2.0 ports in
BIOS settings, those ports will be enabled anyway after you remove a
device on that port and re-plug it in again. It's a known limitation of
the chip. As a workaround we can clear the PORT_WAKE_BITS.
This will disable wake on connect, disconnect and overcurrent on
AMD Promontory USB2 ports
[checkpatch cleanup and commit message reword -Mathias]
Cc: <stable@vger.kernel.org>
Cc: Tsai Nicholas <nicholas.tsai@amd.com>
Signed-off-by: Jiahau Chang <Lars_Chang@asmedia.com.tw>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some new modem device ids.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=rha4
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.12-rc6
Here are some new modem device ids.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
Whishkey cove PMIC has support to mask/unmask interrupts at two levels.
At first level we can mask/unmask interrupt domains like TMU, GPIO, ADC,
CHGR, BCU THERMAL and PWRBTN and at second level, it provides facility
to mask/unmask individual interrupts belong each of this domain. For
example, in case of TMU, at first level we have TMU interrupt domain,
and at second level we have two interrupts, wake alarm, system alarm that
belong to the TMU interrupt domain.
Currently, in this driver all first level IRQs are registered as part of
IRQ chip(bxtwc_regmap_irq_chip). By default, after you register the IRQ
chip from your driver, all IRQs in that chip will masked and can only be
enabled if that IRQ is requested using request_irq() call. This is the
default Linux IRQ behavior model. And whenever a dependent device that
belongs to PMIC requests only the second level IRQ and not explicitly
unmask the first level IRQ, then in essence the second level IRQ will
still be disabled. For example, if TMU device driver request wake_alarm
IRQ and not explicitly unmask TMU level 1 IRQ then according to the default
Linux IRQ model, wake_alarm IRQ will still be disabled. So the proper
solution to fix this issue is to use the chained IRQ chip concept. We
should chain all the second level chip IRQs to the corresponding first
level IRQ. To do this, we need to create separate IRQ chips for every
group of second level IRQs.
In case of TMU, when adding second level IRQ chip, instead of using PMIC
IRQ we should use the corresponding first level IRQ. So the following
code will change from
ret = regmap_add_irq_chip(pmic->regmap, pmic->irq, ...)
to,
virq = regmap_irq_get_virq(&pmic->irq_chip_data, BXTWC_TMU_LVL1_IRQ);
ret = regmap_add_irq_chip(pmic->regmap, virq, ...)
In case of Whiskey Cove Type-C driver, Since USBC IRQ is moved under
charger level2 IRQ chip. We should use charger IRQ chip(irq_chip_data_chgr)
to get the USBC virtual IRQ number.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Revieved-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds a new function 'f_uac1'
(f_uac1 with virtual "ALSA card") that
uses recently created u_audio API. Comparing
to legacy f_uac1 function implementation it
doesn't require any real Audio codec to be
present on the device. In f_uac1 audio
streams are simply sinked to and sourced
from a virtual ALSA sound card created
using u_audio API.
Legacy f_uac1 approach is to write audio
samples directly to existing ALSA sound
card
f_uac1 approach is more generic/flexible
one - create an ALSA sound card that
represents USB Audio function and allows to
be used by userspace application that
may choose to do whatever it wants with the
data received from the USB Host and choose
to provide whatever it wants as audio data
to the USB Host.
f_uac1 also has capture support (gadget->host)
thanks to easy implementation via u_audio.
By default, capture interface has 48000kHz/2ch
configuration, same as playback channel has.
f_uac1 descriptors naming convention
uses f_uac2 driver naming convention that
makes it more common and meaningful.
Comparing to f_uac1_legacy, the f_uac1 doesn't
have volume/mute functionality. This is because
the f_uac1 volume/mute feature unit was dummy
implementation since that driver creation (2009)
and never had any real volume control or mute
functionality, so there is no any difference
here.
Since f_uac1 functionality, exposed
interface to userspace (virtual ALSA card),
input parameters are so different comparing
to f_uac1_legacy, that there is no any
reason to keep them in the same file/module,
and separate function was created.
g_audio can be built using one of existing
UAC functions (f_uac1, f_uac1_legacy or f_uac2)
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Before introducing new f_uac1 function (with virtual
ALSA card) make current implementation legacy.
This includes renaming of existing files, some
variables, config options and documentation
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Abstract the peripheral side ALSA sound card code from
the f_uac2 function into a component that can be called
by various functions, so the various flavors can be split
apart and selectively reused.
Visible changes:
- add uac_params structure to pass audio paramteres for
g_audio_setup
- make ALSA sound card's name configurable
- add [in/out]_ep_maxpsize
- allocate snd_uac_chip structure during g_audio_setup
- add u_audio_[start/stop]_[capture/playback] functions
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Simplify f_uac2 by removing platform driver/device
creation; use composite's usb_gadget device as
parent for sound card and for debug prints.
This removes extra layer of code without any functional
change.
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
After commit 7e4da3fcf7 ("usb: gadget: composite:
Test get_alt() presence instead of set_alt()") f_uac1
function became broken because it doesn't have
get_alt() callback implementation and composite
framework never set altsetting 1 for audiostreaming
interface. On host site it looks like:
[424339.017711] 21:1:1: usb_set_interface failed (-32)
Since host can't set altsetting 1, it can't start
playing audio.
In order to fix it implemented get_alt along with
minor improvements (error conditions checking)
similar to what existing f_uac2 has.
Cc: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
commit 46ddd79e89 ("usb: gadget: udc: atmel: Remove AVR32 bits from the
driver") left the accessor macros introduced by commit a3dd3befd7 ("usb:
gadget: atmel_usba: use endian agnostic IO on ARM"). They can now be
removed.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Corrected the register to check the 64-bit pointer
capability state. 64-bit pointer implementation capability
was checking in wrong register, which causes the BDC
enumeration failure in 64-bit memory address.
Fixes: efed421a94 ("usb: gadget: Add UDC driver for
Broadcom USB3.0 device controller IP BDC")
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Here are some small gadget and xhci USB fixes for 4.12-rc6.
Nothing major, but one of the gadget patches does fix a reported oops,
and the xhci ones resolve reported problems. All have been in
linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWUUFyA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylQ4gCfYyKEsNf9NDKTEw9vNmCNRpsHMa4AoMmdVqmb
lyQAz7Uw2liD+XeBj/qJ
=eAqv
-----END PGP SIGNATURE-----
Merge tag 'usb-4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small gadget and xhci USB fixes for 4.12-rc6.
Nothing major, but one of the gadget patches does fix a reported oops,
and the xhci ones resolve reported problems. All have been in
linux-next with no reported issues"
* tag 'usb-4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: gadgetfs, dummy-hcd, net2280: fix locking for callbacks
usb: xhci: ASMedia ASM1042A chipset need shorts TX quirk
usb: xhci: Fix USB 3.1 supported protocol parsing
USB: gadget: fix GPF in gadgetfs
usb: gadget: composite: make sure to reactivate function on unbind
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions return void * and remove all the casts across
the tree, adding a (u8 *) cast only where the unsigned char pointer
was used directly, all done with the following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
@@
expression SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- fn(SKB, LEN)[0]
+ *(u8 *)fn(SKB, LEN)
Note that the last part there converts from push(...)[0] to the
more idiomatic *(u8 *)push(...).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions (skb_put, __skb_put and pskb_put) return void *
and remove all the casts across the tree, adding a (u8 *) cast only
where the unsigned char pointer was used directly, all done with the
following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_put, __skb_put };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_put, __skb_put };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
which actually doesn't cover pskb_put since there are only three
users overall.
A handful of stragglers were converted manually, notably a macro in
drivers/isdn/i4l/isdn_bsdcomp.c and, oddly enough, one of the many
instances in net/bluetooth/hci_sock.c. In the former file, I also
had to fix one whitespace problem spatch introduced.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.
An spatch similar to the one for skb_put_zero() converts many
of the places using it:
@@
identifier p, p2;
expression len, skb, data;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_data(skb, data, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_data(skb, data, len);
)
(
p2 = (t2)p;
-memcpy(p2, data, len);
|
-memcpy(p, data, len);
)
@@
type t, t2;
identifier p, p2;
expression skb, data;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
)
(
p2 = (t2)p;
-memcpy(p2, data, sizeof(*p));
|
-memcpy(p, data, sizeof(*p));
)
@@
expression skb, len, data;
@@
-memcpy(skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);
(again, manually post-processed to retain some comments)
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were many places that my previous spatch didn't find,
as pointed out by yuan linyu in various patches.
The following spatch found many more and also removes the
now unnecessary casts:
@@
identifier p, p2;
expression len;
expression skb;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_zero(skb, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_zero(skb, len);
)
... when != p
(
p2 = (t2)p;
-memset(p2, 0, len);
|
-memset(p, 0, len);
)
@@
type t, t2;
identifier p, p2;
expression skb;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_zero(skb, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_zero(skb, sizeof(t));
)
... when != p
(
p2 = (t2)p;
-memset(p2, 0, sizeof(*p));
|
-memset(p, 0, sizeof(*p));
)
@@
expression skb, len;
@@
-memset(skb_put(skb, len), 0, len);
+skb_put_zero(skb, len);
Apply it to the tree (with one manual fixup to keep the
comment in vxlan.c, which spatch removed.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
finish_td() could be called with a skip option to bypass most of the
function and only call xhci_td_cleanup() at the end.
Remove this skip option and call xhci_td_cleanup() directly instead
when needed
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Get rid of stopped_stream member in virtual endpoint structure as
it is only used in one case when cleaning a halted endpoint.
Pass it as function parameter instead.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most transfer events have a TRB pointer indicating which TRB caused
the event.
In the case of streams, transfer events such as
USB Transaction error may have its TRB pointer set to zero.
driver won't know which stream or what TRB on that stream caused
the error, but it can issue a soft reset to recover the transfer.
A soft reset will clear the host side halt of the endpoint without
clearing Data toggle or sequence number, and let the transfer
continue from where it halted.
see xhci section 4.12 streams and 4.6.8.2 soft retry.
USB Transaction errors with a zero TRB pointer are seen with
UAS usb devices.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add soft reset support to cleanup_halted_endpoint().
using soft reset will prevent it from setting a new dequeue pointer to
start the transfer from. Let it continue where it halted.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci supports soft retry recovery when the host halted the host side of an
endopint but the connected USB device is not aware of the halt.
In this case xhci needs to issue a reset endopint command with a TSP
(Transfer State Preserve) flag set which preserves the Data toggle
and Sequence number of the endpoint.
This feature is needed to handle a few special transfer event types
such as USB Transaction error that don't always point to a causing TRB.
see xhci 4.6.8.1 for more details
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Parse the transfer event first, and remove duplicate debugging
code.
Reorder completion codes according to endpoint state.
No functional changes
We are not handling some transfer events correcly and need to
clean up this before fixing it
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Anurag Kumar Vulisha reported several issues with xhci endpoint
ring caching.
31 Rings are cached per device before a ring is freed.
These cached rings are not used as default if a new ring is needed.
They are only used if the driver fails to allocate memory for a ring.
The current ring cache is more a reason to why we run out memory than a
help when we actually do so.
Anurag Kumar Vulisha tried to use cached rings as a first option and
found new issues with cached ring initialization.
Cached rings were first zeroed and then manually reinitialized with link
trbs etc, but forgetting to set some important bits like cycle toggle bit.
Remove the ring cache completely as it's a faulty premature optimization
eating memory
Reported-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Tested-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original motivation for disabling/enabling Link PM at device
suspend/resume was to force link state to go via U0 before suspend sets
the link state to U3. Going directly from U2 to U3 is not allowed.
Disabling LPM will forced the link state to U0, but will send a lot of
Set port feature requests for evert suspend and resume.
This is not needed as Hub hardware will take care of going via U0
when a U2 -> U3 transition is requested [1]
[1] USB 3.1 specification section 10.16.2.10 Set Port Feature:
"If the value is 3, then host software wants to selectively suspend the
device connected to this port. The hub shall transition the link to U3
from any of the other U states using allowed link state transitions.
If the port is not already in the U0 state, then it shall transition the
port to the U0 state and then initiate the transition to U3.
While this state is active, the hub does not propagate downstream-directed
traffic to this port, but the hub will respond to resume signaling from the
port"
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using the syzkaller kernel fuzzer, Andrey Konovalov generated the
following error in gadgetfs:
> BUG: KASAN: use-after-free in __lock_acquire+0x3069/0x3690
> kernel/locking/lockdep.c:3246
> Read of size 8 at addr ffff88003a2bdaf8 by task kworker/3:1/903
>
> CPU: 3 PID: 903 Comm: kworker/3:1 Not tainted 4.12.0-rc4+ #35
> Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
> Workqueue: usb_hub_wq hub_event
> Call Trace:
> __dump_stack lib/dump_stack.c:16 [inline]
> dump_stack+0x292/0x395 lib/dump_stack.c:52
> print_address_description+0x78/0x280 mm/kasan/report.c:252
> kasan_report_error mm/kasan/report.c:351 [inline]
> kasan_report+0x230/0x340 mm/kasan/report.c:408
> __asan_report_load8_noabort+0x19/0x20 mm/kasan/report.c:429
> __lock_acquire+0x3069/0x3690 kernel/locking/lockdep.c:3246
> lock_acquire+0x22d/0x560 kernel/locking/lockdep.c:3855
> __raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline]
> _raw_spin_lock+0x2f/0x40 kernel/locking/spinlock.c:151
> spin_lock include/linux/spinlock.h:299 [inline]
> gadgetfs_suspend+0x89/0x130 drivers/usb/gadget/legacy/inode.c:1682
> set_link_state+0x88e/0xae0 drivers/usb/gadget/udc/dummy_hcd.c:455
> dummy_hub_control+0xd7e/0x1fb0 drivers/usb/gadget/udc/dummy_hcd.c:2074
> rh_call_control drivers/usb/core/hcd.c:689 [inline]
> rh_urb_enqueue drivers/usb/core/hcd.c:846 [inline]
> usb_hcd_submit_urb+0x92f/0x20b0 drivers/usb/core/hcd.c:1650
> usb_submit_urb+0x8b2/0x12c0 drivers/usb/core/urb.c:542
> usb_start_wait_urb+0x148/0x5b0 drivers/usb/core/message.c:56
> usb_internal_control_msg drivers/usb/core/message.c:100 [inline]
> usb_control_msg+0x341/0x4d0 drivers/usb/core/message.c:151
> usb_clear_port_feature+0x74/0xa0 drivers/usb/core/hub.c:412
> hub_port_disable+0x123/0x510 drivers/usb/core/hub.c:4177
> hub_port_init+0x1ed/0x2940 drivers/usb/core/hub.c:4648
> hub_port_connect drivers/usb/core/hub.c:4826 [inline]
> hub_port_connect_change drivers/usb/core/hub.c:4999 [inline]
> port_event drivers/usb/core/hub.c:5105 [inline]
> hub_event+0x1ae1/0x3d40 drivers/usb/core/hub.c:5185
> process_one_work+0xc08/0x1bd0 kernel/workqueue.c:2097
> process_scheduled_works kernel/workqueue.c:2157 [inline]
> worker_thread+0xb2b/0x1860 kernel/workqueue.c:2233
> kthread+0x363/0x440 kernel/kthread.c:231
> ret_from_fork+0x2a/0x40 arch/x86/entry/entry_64.S:424
>
> Allocated by task 9958:
> save_stack_trace+0x1b/0x20 arch/x86/kernel/stacktrace.c:59
> save_stack+0x43/0xd0 mm/kasan/kasan.c:513
> set_track mm/kasan/kasan.c:525 [inline]
> kasan_kmalloc+0xad/0xe0 mm/kasan/kasan.c:617
> kmem_cache_alloc_trace+0x87/0x280 mm/slub.c:2745
> kmalloc include/linux/slab.h:492 [inline]
> kzalloc include/linux/slab.h:665 [inline]
> dev_new drivers/usb/gadget/legacy/inode.c:170 [inline]
> gadgetfs_fill_super+0x24f/0x540 drivers/usb/gadget/legacy/inode.c:1993
> mount_single+0xf6/0x160 fs/super.c:1192
> gadgetfs_mount+0x31/0x40 drivers/usb/gadget/legacy/inode.c:2019
> mount_fs+0x9c/0x2d0 fs/super.c:1223
> vfs_kern_mount.part.25+0xcb/0x490 fs/namespace.c:976
> vfs_kern_mount fs/namespace.c:2509 [inline]
> do_new_mount fs/namespace.c:2512 [inline]
> do_mount+0x41b/0x2d90 fs/namespace.c:2834
> SYSC_mount fs/namespace.c:3050 [inline]
> SyS_mount+0xb0/0x120 fs/namespace.c:3027
> entry_SYSCALL_64_fastpath+0x1f/0xbe
>
> Freed by task 9960:
> save_stack_trace+0x1b/0x20 arch/x86/kernel/stacktrace.c:59
> save_stack+0x43/0xd0 mm/kasan/kasan.c:513
> set_track mm/kasan/kasan.c:525 [inline]
> kasan_slab_free+0x72/0xc0 mm/kasan/kasan.c:590
> slab_free_hook mm/slub.c:1357 [inline]
> slab_free_freelist_hook mm/slub.c:1379 [inline]
> slab_free mm/slub.c:2961 [inline]
> kfree+0xed/0x2b0 mm/slub.c:3882
> put_dev+0x124/0x160 drivers/usb/gadget/legacy/inode.c:163
> gadgetfs_kill_sb+0x33/0x60 drivers/usb/gadget/legacy/inode.c:2027
> deactivate_locked_super+0x8d/0xd0 fs/super.c:309
> deactivate_super+0x21e/0x310 fs/super.c:340
> cleanup_mnt+0xb7/0x150 fs/namespace.c:1112
> __cleanup_mnt+0x1b/0x20 fs/namespace.c:1119
> task_work_run+0x1a0/0x280 kernel/task_work.c:116
> exit_task_work include/linux/task_work.h:21 [inline]
> do_exit+0x18a8/0x2820 kernel/exit.c:878
> do_group_exit+0x14e/0x420 kernel/exit.c:982
> get_signal+0x784/0x1780 kernel/signal.c:2318
> do_signal+0xd7/0x2130 arch/x86/kernel/signal.c:808
> exit_to_usermode_loop+0x1ac/0x240 arch/x86/entry/common.c:157
> prepare_exit_to_usermode arch/x86/entry/common.c:194 [inline]
> syscall_return_slowpath+0x3ba/0x410 arch/x86/entry/common.c:263
> entry_SYSCALL_64_fastpath+0xbc/0xbe
>
> The buggy address belongs to the object at ffff88003a2bdae0
> which belongs to the cache kmalloc-1024 of size 1024
> The buggy address is located 24 bytes inside of
> 1024-byte region [ffff88003a2bdae0, ffff88003a2bdee0)
> The buggy address belongs to the page:
> page:ffffea0000e8ae00 count:1 mapcount:0 mapping: (null)
> index:0x0 compound_mapcount: 0
> flags: 0x100000000008100(slab|head)
> raw: 0100000000008100 0000000000000000 0000000000000000 0000000100170017
> raw: ffffea0000ed3020 ffffea0000f5f820 ffff88003e80efc0 0000000000000000
> page dumped because: kasan: bad access detected
>
> Memory state around the buggy address:
> ffff88003a2bd980: fb fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
> ffff88003a2bda00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
> >ffff88003a2bda80: fc fc fc fc fc fc fc fc fc fc fc fc fb fb fb fb
> ^
> ffff88003a2bdb00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
> ffff88003a2bdb80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
> ==================================================================
What this means is that the gadgetfs_suspend() routine was trying to
access dev->lock after it had been deallocated. The root cause is a
race in the dummy_hcd driver; the dummy_udc_stop() routine can race
with the rest of the driver because it contains no locking. And even
when proper locking is added, it can still race with the
set_link_state() function because that function incorrectly drops the
private spinlock before invoking any gadget driver callbacks.
The result of this race, as seen above, is that set_link_state() can
invoke a callback in gadgetfs even after gadgetfs has been unbound
from dummy_hcd's UDC and its private data structures have been
deallocated.
include/linux/usb/gadget.h documents that the ->reset, ->disconnect,
->suspend, and ->resume callbacks may be invoked in interrupt context.
In general this is necessary, to prevent races with gadget driver
removal. This patch fixes dummy_hcd to retain the spinlock across
these calls, and it adds a spinlock acquisition to dummy_udc_stop() to
prevent the race.
The net2280 driver makes the same mistake of dropping the private
spinlock for its ->disconnect and ->reset callback invocations. The
patch fixes it too.
Lastly, since gadgetfs_suspend() may be invoked in interrupt context,
it cannot assume that interrupts are enabled when it runs. It must
use spin_lock_irqsave() instead of spin_lock_irq(). The patch fixes
that bug as well.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Andrey Konovalov <andreyknvl@google.com>
CC: <stable@vger.kernel.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull networking fixes from David Miller:
1) The netlink attribute passed in to dev_set_alias() is not
necessarily NULL terminated, don't use strlcpy() on it. From
Alexander Potapenko.
2) Fix implementation of atomics in arm64 bpf JIT, from Daniel
Borkmann.
3) Correct the release of netdevs and driver private data in certain
circumstances.
4) Sanitize netlink message length properly in decnet, from Mateusz
Jurczyk.
5) Don't leak kernel data in rtnl_fill_vfinfo() netlink blobs. From
Yuval Mintz.
6) Hash secret is never initialized in ipv6 ILA translation code, from
Arnd Bergmann. I guess those clang warnings about unused inline
functions are useful for something!
7) Fix endian selection in bpf_endian.h, from Daniel Borkmann.
8) Sanitize sockaddr length before dereferncing any fields in AF_UNIX
and CAIF. From Mateusz Jurczyk.
9) Fix timestamping for GMAC3 chips in stmmac driver, from Mario
Molitor.
10) Do not leak netdev on dev_alloc_name() errors in mac80211, from
Johannes Berg.
11) Fix locking in sctp_for_each_endpoint(), from Xin Long.
12) Fix wrong memset size on 32-bit in snmp6, from Christian Perle.
13) Fix use after free in ip_mc_clear_src(), from WANG Cong.
14) Fix regressions caused by ICMP rate limiting changes in 4.11, from
Jesper Dangaard Brouer.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (91 commits)
i40e: Fix a sleep-in-atomic bug
net: don't global ICMP rate limit packets originating from loopback
net/act_pedit: fix an error code
net: update undefined ->ndo_change_mtu() comment
net_sched: move tcf_lock down after gen_replace_estimator()
caif: Add sockaddr length check before accessing sa_family in connect handler
qed: fix dump of context data
qmi_wwan: new Telewell and Sierra device IDs
net: phy: Fix MDIO_THUNDER dependencies
netconsole: Remove duplicate "netconsole: " logging prefix
igmp: acquire pmc lock for ip_mc_clear_src()
r8152: give the device version
net: rps: fix uninitialized symbol warning
mac80211: don't send SMPS action frame in AP mode when not needed
mac80211/wpa: use constant time memory comparison for MACs
mac80211: set bss_info data before configuring the channel
mac80211: remove 5/10 MHz rate code from station MLME
mac80211: Fix incorrect condition when checking rx timestamp
mac80211: don't look at the PM bit of BAR frames
i40e: fix handling of HW ATR eviction
...
clk_prepare_enable() can fail here and we must check its return value.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
hcd_pci_resume_noirq() used as a universal _resume_noirq handler for
PCI USB controllers calls pci_back_from_sleep() which is unnecessary
and may become problematic.
It is unnecessary, because the PCI bus type carries out post-suspend
cleanup of all PCI devices during resume and that covers all things
done by the pci_back_from_sleep(). There is no reason why USB cannot
follow all of the other PCI devices in that respect.
It will become problematic after subsequent changes that make it
possible to go back to sleep again after executing dpm_resume_noirq()
if no valid system wakeup events have been detected at that point.
Namely, calling pci_back_from_sleep() at the _resume_noirq stage
will cause the wakeup status of the devices in question to be cleared
and if any of them has triggered system wakeup, that event may be
missed then.
For the above reasons, drop the pci_back_from_sleep() invocation
from hcd_pci_resume_noirq().
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A new Sierra Wireless EM7305 device ID used in a Toshiba laptop.
Reported-by: Petr Kloc <petr_kloc@yahoo.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
The commit 47d3946ea2
usb: dwc3: refactor gadget endpoint count calculation
refactored dwc3_gadget_init_endpoints() and in particular changed in or
out endpoint numbering to be through. It's not always convenient and
makes code a slightly harder to read.
Introduce a new temporary variable to make it easier to understand what
is going on inside the function.
While doing that, rename local variables as follows:
u8 num -> u8 total
int num -> int kbytes
Replace implicit direction check via epnum with explicit use of
direction variable.
While here, replace %d to %u when compounding endpoint name since we are
using unsigned type.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If there is no UDC available, the msg register will fail and this
flag will not be set, but the driver is already added into pending
driver list, then the module removal modprobe -r can not remove
the driver from the pending list.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The USB3.0 peripheral controller on R-Car SoCs has a dedicated DMAC.
The DMAC needs a "PRD table" in system memory and the DMAC can have
four PRD tables. This patch adds support for the DMAC.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
AVR32 is gone. Now it's time to clean up the driver by removing
leftovers that was used by AVR32 related code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If don't reorder initialization like this, we will never be able to
get a reference to ULPI PHYs.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If PHY is suspended by the time we want to issue ULPI transfers, we
will observe timeouts on the ULPI interface. In order to avoid such
issue, let's make sure PHY is resumed before issuing a ULPI transfer.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This file will print out the name of the currently running USB Gadget
Driver. It can be read even when there are no functions loaded.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use this method to make sure we don't try to connect on speeds not
supported by the gadget driver.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Sometimes, the gadget driver we want to run has max_speed lower than
what the UDC supports. In such situations, UDC might want to make sure
we don't try to connect on speeds not supported by the gadget
driver (e.g. super-speed capable dwc3 with high-speed capable g_midi)
because that will just fail.
In order to make sure this situation never happens, we introduce a new
optional ->udc_set_speed() method which can be implemented by
interested UDC drivers.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds platform driver support for Synopsys UDC.
A new driver file (snps_udc_plat.c) is created for this purpose
where the platform driver registration is done based on OF
node.
Currently, UDC integrated into Broadcom's iProc SoCs (Northstar2
and Cygnus) work with this driver.
New members are added to the UDC data structure for having platform
device support along with extcon and phy support.
Kconfig and Makefiles are modified to select platform driver for
compilation.
Signed-off-by: Raviteja Garimella <raviteja.garimella@broadcom.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Change the argument from NULL to a struct device for the
dma_pool_create call during dma init.
Signed-off-by: Raviteja Garimella <raviteja.garimella@broadcom.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds a struct device member to UDC data structure and
makes changes to the arguments of dev_err and dev_dbg calls so that
the debug prints work for both pci and platform devices.
Signed-off-by: Raviteja Garimella <raviteja.garimella@broadcom.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch renames the amd5536udc.c that has the core driver
functionality of Synopsys UDC to snps_udc_core.c
The symbols exported here can be used by any UDC driver that uses
the same Synopsys IP.
Signed-off-by: Raviteja Garimella <raviteja.garimella@broadcom.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Other unsigned properties return hexadecimal values, follow this
convention when printing b_vendor_code too. Also add newlines to
the OS Descriptor support related properties, like other sysfs
files use.
Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Currently qw_sign requires UTF-8 character to set, but returns UTF-16
when read. This isn't obvious when simply using cat since the null
characters are not visible, but hexdump unveils the true string:
# echo MSFT100 > os_desc/qw_sign
# hexdump -C os_desc/qw_sign
00000000 4d 00 53 00 46 00 54 00 31 00 30 00 30 00 |M.S.F.T.1.0.0.|
Make qw_sign symmetric by returning an UTF-8 string too. Also follow
common convention and add a new line at the end.
Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Remove the broken alt_speed code, and warn when trying to set the line
speed using TIOCSSERIAL and SPD flags.
The use of SPD flags to set the line speed has been deprecated since
v2.1.69 and support for alt_speed (e.g. "warp") has even been removed
from TTY core in v3.10 by commit 6865ff222c ("TTY: do not warn about
setting speed via SPD_*"), effectively breaking all driver
implementations of this except for serial core.
Also remove the verbose and outdated comment on how to set baud rates.
Note that setting a custom divisor will continue to work with the
caveat that 38400 must again be selected every time the divisor is
changed since v2.6.24 and commit 669a6db103 ("USB: ftd_sio: cleanups
and updates for new termios work") which started reporting back the
actual baud rate used.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In an attempt to work around a pinmux over-allocation issue in driver
core, commit dc5878abf4 ("usb: core: move root hub's device node
assignment after it is added to bus") moved the device-tree node
assignment until after the root hub had been registered.
This not only makes the device-tree node unavailable to the usb driver
during probe, but also prevents the of_node from being linked to in
sysfs and causes a race with user-space for the (recently added) devspec
attribute.
Use the new device_set_of_node_from_dev() helper to reuse the node of
the sysdev device, something which now prevents driver core from trying
to reclaim any pinctrl pins during probe.
Fixes: dc5878abf4 ("usb: core: move root hub's device node assignment after it is added to bus")
Fixes: 51fa91475e ("usb/core: Added devspec sysfs entry for devices behind the usb hub")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Document that the child-node lookup helper takes a reference to the
device-tree node which needs to be dropped after use.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to release any OF device-node reference taken when creating
the USB device.
Note that we currently do not hold a reference to the root hub
device-tree node (i.e. the parent controller node).
Fixes: 69bec72598 ("USB: core: let USB device know device node")
Cc: stable <stable@vger.kernel.org> # v4.6
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use sysfs_match_string() helper instead of open coded variant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trace_printk() was used to log debug messages in xhci-dbc.c where
printk() isn't feasible. As there should not be a single caller to
trace_printk() in normal kernels, replace them with empty functions.
Cc: Vlastimil Babka <vbabka.lkml@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Each vhci has 2*VHCI_HC_PORTS ports, in which VHCI_HC_PORTS
ports are HighSpeed (or below), and VHCI_HC_PORTS are SuperSpeed.
This new macro VHCI_PORTS reflects this configuration.
Signed-off-by: Yuyang Du <yuyang.du@intel.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As USB3 has (slightly) different bit meanings in the port
status. Add a new status bit array for USB3.
Signed-off-by: Yuyang Du <yuyang.du@intel.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With this patch, USB_SPEED_SUPER is a valid speed when attaching
a USB3 SuperSpeed device.
Signed-off-by: Yuyang Du <yuyang.du@intel.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a USB3 HCD to an existing USB2 HCD and provides
the support of SuperSpeed, in case the device can only be enumerated
with SuperSpeed.
The bulk of the added code in usb3_bos_desc and hub_control to support
SuperSpeed is borrowed from the commit 1cd8fd2887 ("usb: gadget:
dummy_hcd: add SuperSpeed support").
With this patch, each vhci will have VHCI_HC_PORTS HighSpeed ports
and VHCI_HC_PORTS SuperSpeed ports.
Suggested-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Yuyang Du <yuyang.du@intel.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch enables the new vhci structure. Its lock protects
both the USB2 hub and the shared USB3 hub.
Signed-off-by: Yuyang Du <yuyang.du@intel.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A vhci struct is added as the platform-specific data to the vhci
platform device, in order to get the vhci by its platform device.
This is done in vhci_hcd_init().
Signed-off-by: Yuyang Du <yuyang.du@intel.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Every VHCI is a platform device, so move the platform_device struct
into the VHCI struct.
Signed-off-by: Yuyang Du <yuyang.du@intel.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to support SuperSpeed devices, a USB3 HCD is added to
share the USB2 HCD. As a result, a VHCI is composed of two
vhci_hcds associated with the two HCDs respectively. So we add
another level of abstraction, vhci, and thus this vhci structure.
Signed-off-by: Yuyang Du <yuyang.du@intel.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These helper function names are renamed to have their full struct
names to avoid confusion:
- hcd_to_vhci() -> hcd_to_vhci_hcd()
- vhci_to_hcd() -> vhci_hcd_to_hcd()
- vdev_to_vhci() -> vdev_to_vhci_hcd()
Signed-off-by: Yuyang Du <yuyang.du@intel.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usbip stack dynamically allocates the transfer_buffer and
setup_packet of each urb that got generated by the tcp to usb stub code.
As these pointers are always used only once we will set them to NULL
after use. This is done likewise to the free_urb code in vudc_dev.c.
This patch fixes double kfree situations where the usbip remote side
added the URB_FREE_BUFFER.
Cc: stable@vger.kernel.org
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usbfs interface does not provide any way for the user to learn the
speed at which a device is connected. The current API includes a
USBDEVFS_CONNECTINFO ioctl, but all it provides is the device's
address and a one-bit value indicating whether the connection is low
speed. That may have sufficed in the era of USB-1.1, but it isn't
good enough today.
This patch introduces a new ioctl, USBDEVFS_GET_SPEED, which returns a
numeric value indicating the speed of the connection: unknown, low,
full, high, wireless, super, or super-plus.
Similar information (not exactly the same) is available through sysfs,
but it seems reasonable to provide the actual value in usbfs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Reinhard Huck <reinhard.huck@thesycon.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The qcserial driver fails to expose the .tiocmget and .tiocmset methods
available from usb_wwan. These methods are required by ioctl commands
dealing with the modem control signals DTR, RTS, etc.
With these methods not set ioctl calls intended to control the DTR state
will fail. For example, pppd drops and raises DTR in preparation to
dialing the modem, which handles the case of the modem already being
connected by making it hang up and return to command mode. DTR control
being unavailable will lead to a protracted failure to connect as the
modem will be stuck in a state not responsive to command.
I have tested that with this patch the described case is handled
successfully. There is an analogous method for .ioctl available from
usb_wwan (as used in option.c) but I conservatively omitted that for
lack of familiarity.
Signed-off-by: Magnus Lynch <maglyx@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
We are trying to get rid of DRIVER_ATTR(), and the usbip driver
attribute can be trivially changed to use DRIVER_ATTR_RW().
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Cc: <linux-usb@vger.kernel.org>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When plugging an USB webcam I see the following message:
[106385.615559] xhci_hcd 0000:04:00.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[106390.583860] handle_tx_event: 913 callbacks suppressed
With this patch applied, I get no more printing of this message.
Cc: <stable@vger.kernel.org>
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xHCI host controllers can have both USB 3.1 and 3.0 extended speed
protocol lists. If the USB3.1 speed is parsed first and 3.0 second then
the minor revision supported will be overwritten by the 3.0 speeds and
the USB3 roothub will only show support for USB 3.0 speeds.
This was the case with a xhci controller with the supported protocol
capability listed below.
In xhci-mem.c, the USB 3.1 speed is parsed first, the min_rev of usb3_rhub
is set as 0x10. And then USB 3.0 is parsed. However, the min_rev of
usb3_rhub will be changed to 0x00. If USB 3.1 device is connected behind
this host controller, the speed of USB 3.1 device just reports 5G speed
using lsusb.
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
00 01 08 00 00 00 00 00 40 00 00 00 00 00 00 00 00
10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20 02 08 10 03 55 53 42 20 01 02 00 00 00 00 00 00 //USB 3.1
30 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40 02 08 00 03 55 53 42 20 03 06 00 00 00 00 00 00 //USB 3.0
50 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60 02 08 00 02 55 53 42 20 09 0E 19 00 00 00 00 00 //USB 2.0
70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
This patch fixes the issue by only owerwriting the minor revision if
it is higher than the existing one.
[reword commit message -Mathias]
Cc: <stable@vger.kernel.org>
Signed-off-by: YD Tseng <yd_tseng@asmedia.com.tw>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern fixed a GPF in gadgetfs found by the kernel fuzzying project
composite.c learned that if it deactivates a function during bind, it
must reactivate it during unbind.
-----BEGIN PGP SIGNATURE-----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=S9bm
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.12-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.12-rc5
Alan Stern fixed a GPF in gadgetfs found by the kernel fuzzying project
composite.c learned that if it deactivates a function during bind, it
must reactivate it during unbind.
Network devices can allocate reasources and private memory using
netdev_ops->ndo_init(). However, the release of these resources
can occur in one of two different places.
Either netdev_ops->ndo_uninit() or netdev->destructor().
The decision of which operation frees the resources depends upon
whether it is necessary for all netdev refs to be released before it
is safe to perform the freeing.
netdev_ops->ndo_uninit() presumably can occur right after the
NETDEV_UNREGISTER notifier completes and the unicast and multicast
address lists are flushed.
netdev->destructor(), on the other hand, does not run until the
netdev references all go away.
Further complicating the situation is that netdev->destructor()
almost universally does also a free_netdev().
This creates a problem for the logic in register_netdevice().
Because all callers of register_netdevice() manage the freeing
of the netdev, and invoke free_netdev(dev) if register_netdevice()
fails.
If netdev_ops->ndo_init() succeeds, but something else fails inside
of register_netdevice(), it does call ndo_ops->ndo_uninit(). But
it is not able to invoke netdev->destructor().
This is because netdev->destructor() will do a free_netdev() and
then the caller of register_netdevice() will do the same.
However, this means that the resources that would normally be released
by netdev->destructor() will not be.
Over the years drivers have added local hacks to deal with this, by
invoking their destructor parts by hand when register_netdevice()
fails.
Many drivers do not try to deal with this, and instead we have leaks.
Let's close this hole by formalizing the distinction between what
private things need to be freed up by netdev->destructor() and whether
the driver needs unregister_netdevice() to perform the free_netdev().
netdev->priv_destructor() performs all actions to free up the private
resources that used to be freed by netdev->destructor(), except for
free_netdev().
netdev->needs_free_netdev is a boolean that indicates whether
free_netdev() should be done at the end of unregister_netdevice().
Now, register_netdevice() can sanely release all resources after
ndo_ops->ndo_init() succeeds, by invoking both ndo_ops->ndo_uninit()
and netdev->priv_destructor().
And at the end of unregister_netdevice(), we invoke
netdev->priv_destructor() and optionally call free_netdev().
Signed-off-by: David S. Miller <davem@davemloft.net>
acpi_evaluate_dsm() and friends take a pointer to a raw buffer of 16
bytes. Instead we convert them to use guid_t type. At the same time we
convert current users.
acpi_str_to_uuid() becomes useless after the conversion and it's safe to
get rid of it.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Cc: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
If a function sets bind_deactivated flag, upon removal we will be left
with an unbalanced deactivation. Let's make sure that we conditionally
call usb_function_activate() from usb_remove_function() and make sure
usb_remove_function() is called from remove_config().
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This driver is no longer needed and can be removed. The reason why
it's safe to remove this driver is that most omap devices don't have a
USB low-speed or full-speed compatible PHY installed and configured
with drivers/mfd/omap-usb-host.c. This means that devices like
beagleboard and pandaboard need to use a high-speed USB hub in order
to use devices like keyboard and mice.
Currently the only known configured for a full-speed PHY is the
mdm6600 modem on droid 4 and I've verified it works just fine with
ohci-platform.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the runtime PM implemented for ohci-platform driver, we can
now support omap3 and later OHCI by adding one device tree
property.
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is needed in preparation of adding support for omap3 and
later OHCI. The runtime PM will only do something on platforms
that implement it.
Cc: devicetree@vger.kernel.org
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Start using ktime_* compare functions to make the code backportable.
Now that may be a bit tricky due to recent change of ktime_t.
Signed-off-by: Mariusz Skamra <mariuszx.skamra@intel.com>
Acked-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
User space applications in some cases have the need to enforce a
specific port type(DFP/UFP/DRP). This change allows userspace to
attempt setting the desired port type. Low level drivers can
however reject the request if the specific port type is not supported.
Signed-off-by: Badhri Jagan Sridharan <Badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If USB PD contract is established after creation of the
partner, the power delivery support attribute of the partner
needs to be updated separately. This can be done in
typec_set_pwr_opmode() by checking if the port has already
partner and updating the value if it does.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add xhci_get_hw_deq() helper to retrieve the hardware dequeue pointer an
endpoint or stream stopped on.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The values for the new dequeue segment, new dequeue pointer and new cycle
state are needed for manually moving the xHC ring dequeue pointer.
These are conveniently stored in a xhci_dequeue_state structure.
stream support was added later and stream_id was carried
as a function parameter.
Move the stream_id to the xhci_dequeue_state structure instead.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When xHC is asked to stop an endpoint it will save the position it
stopped on in the endpoint or stream context.
xhci driver needs to know if the controller stopped on the exact same
TRB that the driver was asked to cancel as it then needs to move past
the TD instead of turning the TD to no-op TRBs.
xhci driver used to get the stopped position from a "stopped" transfer
event before the stop endpoint command completed, but if the ring
is already stopped, or in a halted or error state this event is missing.
Get the stopped position from the endpoint or stream context instead
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This optimization significantly reduces xhci driver load time.
In ACPI tables the acpi companion port devices are children of
the hub device. The port devices are identified by their port number
returned by the ACPI _ADR method.
_ADR 0 is reserved for the root hub device.
The current implementation to find a acpi companion port device
loops through all acpi port devices under that parent hub, evaluating
their _ADR method each time a new port device is added.
for a xHC controller with 25 ports under its roothub it
will end up invoking ACPI bytecode 625 times before all ports
are ready, making it really slow.
The _ADR values are already read and cached earler. So instead of
running the bytecode again we can check the cached _ADR value first,
and then fall back to the old way.
As one of the more significant changes, the xhci load time on
Intel kabylake reduced by 70%, (28ms) from
initcall xhci_pci_init+0x0/0x49 returned 0 after 39537 usecs
to
initcall xhci_pci_init+0x0/0x49 returned 0 after 11270 usecs
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We no longer keep track of where we stopped in a stopped_td pointer.
We get the ring dequeue pointer from the endpoint or stream context
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A fix to a really old synchronization bug on mass storage gadget.
Support for Meson8 SoCs on dwc2
Synchronization fixes on renesas USB driver.
-----BEGIN PGP SIGNATURE-----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=P1Tt
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.12-rc4
A fix to a really old synchronization bug on mass storage gadget.
Support for Meson8 SoCs on dwc2
Synchronization fixes on renesas USB driver.
With the new API to perform the in-kernel buffer copy, we can get rid
of set_fs() usage in this driver, finally.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PN_INT_ENA register should be used after usb3_pn_change() is called.
So, this patch moves the access from renesas_usb3_stop_controller() to
usb3_disable_pipe_n().
Fixes: 746bfe63bb ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This controller disallows to change the PIPE until reading/writing
a packet finishes. However. the previous code is not enough to hold
the lock in some functions. So, this patch fixes it.
Fixes: 746bfe63bb ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes an issue that this driver is possible to cause
deadlock by double-spinclocked in renesas_usb3_stop_controller().
So, this patch removes spinlock API calling in renesas_usb3_stop().
(In other words, the previous code had a redundant lock.)
Fixes: 746bfe63bb ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes an issue that this driver is possible to access
the registers before pm_runtime_get_sync() if a gadget driver is
installed first. After that, oops happens on R-Car Gen3 environment.
To avoid it, this patch changes the pm_runtime call timing from
probe/remove to udc_start/udc_stop.
Fixes: 746bfe63bb ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
f_mass_storage has a memorry barrier issue with the sleep and wake
functions that can cause a deadlock. This results in intermittent hangs
during MSC file transfer. The host will reset the device after receiving
no response to resume the transfer. This issue is seen when dwc3 is
processing 2 transfer-in-progress events at the same time, invoking
completion handlers for CSW and CBW. Also this issue occurs depending on
the system timing and latency.
To increase the chance to hit this issue, you can force dwc3 driver to
wait and process those 2 events at once by adding a small delay (~100us)
in dwc3_check_event_buf() whenever the request is for CSW and read the
event count again. Avoid debugging with printk and ftrace as extra
delays and memory barrier will mask this issue.
Scenario which can lead to failure:
-----------------------------------
1) The main thread sleeps and waits for the next command in
get_next_command().
2) bulk_in_complete() wakes up main thread for CSW.
3) bulk_out_complete() tries to wake up the running main thread for CBW.
4) thread_wakeup_needed is not loaded with correct value in
sleep_thread().
5) Main thread goes to sleep again.
The pattern is shown below. Note the 2 critical variables.
* common->thread_wakeup_needed
* bh->state
CPU 0 (sleep_thread) CPU 1 (wakeup_thread)
============================== ===============================
bh->state = BH_STATE_FULL;
smp_wmb();
thread_wakeup_needed = 0; thread_wakeup_needed = 1;
smp_rmb();
if (bh->state != BH_STATE_FULL)
sleep again ...
As pointed out by Alan Stern, this is an R-pattern issue. The issue can
be seen when there are two wakeups in quick succession. The
thread_wakeup_needed can be overwritten in sleep_thread, and the read of
the bh->state maybe reordered before the write to thread_wakeup_needed.
This patch applies full memory barrier smp_mb() in both sleep_thread()
and wakeup_thread() to ensure the order which the thread_wakeup_needed
and bh->state are written and loaded.
However, a better solution in the future would be to use wait_queue
method that takes care of managing memory barrier between waker and
waiter.
Cc: <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
USB support in the Meson8 SoCs is provided by a DWC2 controller which
works with the same settings as Meson8b and GXBB. Using the generic
"snps,dwc2" binding results in an endless stream of "Overcurrent change
detected" messages.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This commit allows a gadget that does not support SuperSpeed to indicate
that it supports LPM. It does this by setting the 'lpm_capable' flag in
the gadget structure.
If a gadget sets this, the composite gadget framework will set the
bcdUSB to 0x0201 to indicate that this supports BOS descriptors, and
also return a USB 2.0 Extension descriptor as part of the BOS descriptor
set.
See USB 2.0 LPM ECN Section 3.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Don't send the SuperSpeed USB Device Capability descriptor if
the gadget is not capable of SuperSpeed.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There were individual waitqueues for each epfile but eps_enable
would iterate through all of them, resulting in essentially the
same wakeup time.
The waitqueue represents the function being enabled, so a central
waitqueue in ffs_data makes more sense and is less redundant.
Also use wake_up_interruptible to reflect use of
wait_event_interruptible.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Jerry Zhang <zhangjerry@google.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This allows users to make an ioctl call as the first action on a
connection. Ex, some functions might want to get endpoint size
before making any i/os.
Previously, calling ioctls before read/write would depending on the
timing of endpoints being enabled.
ESHUTDOWN is now a possible return value and ENODEV is not, so change
docs accordingly.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Jerry Zhang <zhangjerry@google.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The assignment ret = ret is redundant and can be removed.
Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead, we can require caller to pass a buffer for the function to
use. This cleans things quite a bit.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of going for a 512 byte buffer and using snprintf(), let's
rely on helps __string() and __assign_str() where possible.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of printing out enqueue and dequeue pointer value as a header
to the output, let's mark the TRBs in question with 'E' and 'D'. The
output looks slightly easier to read.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
%p will leak kernel pointers, so let's not expose the information on
dmesg and instead use %pK. %pK will only show the actual addresses if
explicitly enabled under /proc/sys/kernel/kptr_restrict.
Cc: <stable@vger.kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some local constants don't change from call to call and are good
candidates to become static. This will prevent copying of these
constants to stack during runtime.
Signed-off-by: Maksim Salau <maksim.salau@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Currently VBUS is turned off while a usb device is detached, and turned
on again by the polling routine. This short period VBUS loss prevents
usb modem to switch mode.
VBUS should be constantly on for host-only mode, so this changes the
driver to not turn off VBUS for host-only mode.
Fixes: 2f3fd2c5bd ("usb: musb: Prepare dsps glue layer for PM runtime support")
Cc: stable@vger.kernel.org #v4.11
Reported-by: Moreno Bartalucci <moreno.bartalucci@tecnorama.it>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The combo of list_empty() and list_first_entry() can be replaced with
list_first_entry_or_null().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Aspeed 2400/2500 families have a variant of UHCI which requires
some quirks to the driver to work:
- The register offsets are different. We add a remapping helper.
- All accesses have to be done via 32-bit loads and stores. We
force all accessors to use readl/writel. This is of no consequence
for reads as we never read "in the middle" of a register. For writes
it also works fine as the registers only actually implement the bits
we try to write (16-bit for the registers accessed with writew and
8-bit for the register accessed with writeb), so always using a
32-bit write will have no negative effect. We never do partial writes.
- The resume detect interrupt is broken
- The number of ports is (optionally) provided via the device-tree
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
--
v2. Remove the bulk of the #ifdef's
drivers/usb/host/Kconfig | 6 ++++-
drivers/usb/host/uhci-hcd.c | 17 +++++++++++---
drivers/usb/host/uhci-hcd.h | 51 ++++++++++++++++++++++++++++++++++++++++
drivers/usb/host/uhci-platform.c | 22 ++++++++++++++++-
4 files changed, 91 insertions(+), 5 deletions(-)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEbBAABAgAGBQJZI4ULAAoJEEhZKYFQ1nG7zS0H9Rq3yIJaLMPI9y4bBatTvP1L
pmKu0/wpCUfzWCOJ4RFp1X0Up2kqe6z7U/+YQLNyRT/1/ssiNuT7BIl+Cy+WtAD5
IN1ChG6769eshd+FT4gpg5TobXIP7daYFHehbe/9UQofyiMukyPaV3lSUR1XO4FB
Z66pGfnij0O+pPkFuQ8ARE/VrHo2vlGC4coOtbUVG8eYMgzjPblPRWFTGVf0LcFq
7p26Ggp3WzsDqP9mwBZUjCFm5TA/9gF14KPywOToarY2Fz2FHTaK82L1r0QnE+61
Fla9TejbW553zuA6SRWOJL8M10TFZ/g/6/FRuVKbfPGHmRzL26v8iwFDhHmKXA==
=WS1v
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-linus
Peter writes:
Some small bugs
ci_role BUGs when the role is >= CI_ROLE_END.
This is the case while the role is changing.
Signed-off-by: Michael Thalmeier <michael.thalmeier@hale.at>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
ci_role BUGs when the role is >= CI_ROLE_END.
Cc: stable@vger.kernel.org #v3.10+
Signed-off-by: Michael Thalmeier <michael.thalmeier@hale.at>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Here's a fix for a long-standing issue in the ftdi_sio driver that
prevented unprivileged users from updating the low-latency flag,
something which became apparent after a recent change that restored the
older setting of not using low-latency mode by default.
A run of sparse revealed a couple of endianness issues that are now
fixed, and addressed is also a user-triggerable division-by-zero in
io_ti when debugging is enabled.
Finally there are some new device ids, including a simplification of how
we deal with a couple of older Olimex JTAG adapters.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=psyq
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.12-rc2
Here's a fix for a long-standing issue in the ftdi_sio driver that
prevented unprivileged users from updating the low-latency flag,
something which became apparent after a recent change that restored the
older setting of not using low-latency mode by default.
A run of sparse revealed a couple of endianness issues that are now
fixed, and addressed is also a user-triggerable division-by-zero in
io_ti when debugging is enabled.
Finally there are some new device ids, including a simplification of how
we deal with a couple of older Olimex JTAG adapters.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
In the ene_usb6250 sub-driver for usb-storage, the INQUIRY data
returned by the driver indicates that the device has removable media.
While this is technically correct (memory cards can be removed from
the reader), it is not useful because the device automatically
disconnects itself from the USB bus when no media is present.
In addition, the driver does not support the PREVENT-ALLOW MEDIUM
REMOVAL and START STOP UNIT commands, and this can cause
user-interface frameworks to get confused when the user asks for the
card to be removed or ejected.
This patch fixes the problem by changing the INQUIRY data to specify
non-removable media; in practice this value works much better.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Andreas Hartmann <andihartmann@01019freenet.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the ene_usb6250 sub-driver for usb-storage, the sd_scsi_inquiry()
and ms_scsi_inquiry() subroutines (one meant for use with SD memory
cards and the other for use with MS memory cards) are exact
duplicates. This patch removes the duplication by creating a single
do_scsi_inquiry() command and using it instead of the other two.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Andreas Hartmann <andihartmann@01019freenet.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the ene_usb6250 sub-driver for usb-storage, there is no support for
the REQUEST SENSE command. This command is issued whenever a failure
occurs, and without it the driver has no way to tell the SCSI core
what the reason for the failure was.
This patch adds a do_scsi_request_sense() routine to the driver. The
new routine reports the error code stored by the previous command.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Andreas Hartmann <andihartmann@01019freenet.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the ene_usb6250 sub-driver for usb-storage, the SCSI residue is not
reported correctly. The residue is initialized to 0, but this value
is overwritten whenever the driver sends firmware to the card reader
before performing the current command. As a result, a valid READ or
WRITE operation appears to have failed, causing the SCSI core to retry
the command multiple times and eventually fail.
This patch fixes the problem by resetting the SCSI residue to 0 after
sending firmware to the device.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Andreas Hartmann <andihartmann@01019freenet.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the ene_usb6250 sub-driver for usb-storage, the ene_transport()
routine is supposed to initialize the driver before executing the
current command, if the initialization has not already been performed.
However, a bug in the routine causes it to skip the command after
doing the initialization. Also, the routine does not return an
appropriate error code if either the initialization or the command
fails.
As a result of the first bug, the first command (a SCSI INQUIRY) is
not carried out. The results can be seen in the system log, in the
form of a warning message and empty or garbage INQUIRY data:
Apr 18 22:40:08 notebook2 kernel: scsi host6: scsi scan: INQUIRY result too short (5), using 36
Apr 18 22:40:08 notebook2 kernel: scsi 6:0:0:0: Direct-Access PQ: 0 ANSI: 0
This patch fixes both errors.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Andreas Hartmann <andihartmann@01019freenet.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have one register for each EP to set the maximum packet size for both
TX and RX.
If for example an RX programming would happen before the previous TX
transfer finishes we would reset the TX packet side.
To fix this issue, only modify the TX or RX part of the register.
Fixes: 550a7375fe ("USB: Add MUSB and TUSB support")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d8e5f0eca1 ("usb: musb: Fix hardirq-safe hardirq-unsafe
lock order error") caused a regression where musb keeps trying to
enable host mode with no cable connected. This seems to be caused
by the fact that now phy is enabled earlier, and we are wrongly
trying to force USB host mode on an OTG port. The errors we are
getting are "trying to suspend as a_idle while active".
For ports configured as OTG, we should not need to do anything
to try to force USB host mode on it's OTG port. Trying to force host
mode in this case just seems to completely confuse the musb state
machine.
Let's fix the issue by making musb_host_setup() attempt to force the
mode only if port_mode is configured for host mode.
Fixes: d8e5f0eca1 ("usb: musb: Fix hardirq-safe hardirq-unsafe lock order error")
Cc: Johan Hovold <johan@kernel.org>
Cc: stable <stable@vger.kernel.org>
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_get_irq() returns an error code, but the xhci-plat driver
ignores it and always returns -ENODEV. This is not correct, and
prevents -EPROBE_DEFER from being propagated properly.
CC: <stable@vger.kernel.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In 4.11 TRB completion codes were renamed to match spec.
Completion codes for command ring stopped and endpoint stopped
were mixed, leading to failures while handling a stopped command ring.
Use the correct completion code for command ring stopped events.
Fixes: 0b7c105a04 ("usb: host: xhci: rename completion codes to match spec")
Cc: <stable@vger.kernel.org> # 4.11
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no reason to restrict allocations to the first 16MB ISA DMA
addresses.
It is causing problems in a virtualization setup with enabled IOMMU
(x86_64). The result is that USB is not working in the VM.
CC: <stable@vger.kernel.org>
Signed-off-by: Matthias Lange <matthias.lange@kernkonzept.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With threaded interrupts, bottom-half handlers are called with
interrupts enabled. Therefore they can't safely use spin_lock(); they
have to use spin_lock_irqsave(). Lockdep warns about a violation
occurring in xhci_irq():
=========================================================
[ INFO: possible irq lock inversion dependency detected ]
4.11.0-rc8-dbg+ #1 Not tainted
---------------------------------------------------------
swapper/7/0 just changed the state of lock:
(&(&ehci->lock)->rlock){-.-...}, at: [<ffffffffa0130a69>]
ehci_hrtimer_func+0x29/0xc0 [ehci_hcd]
but this lock took another, HARDIRQ-unsafe lock in the past:
(hcd_urb_list_lock){+.....}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(hcd_urb_list_lock);
local_irq_disable();
lock(&(&ehci->lock)->rlock);
lock(hcd_urb_list_lock);
<Interrupt>
lock(&(&ehci->lock)->rlock);
*** DEADLOCK ***
no locks held by swapper/7/0.
the shortest dependencies between 2nd lock and 1st lock:
-> (hcd_urb_list_lock){+.....} ops: 252 {
HARDIRQ-ON-W at:
__lock_acquire+0x602/0x1280
lock_acquire+0xd5/0x1c0
_raw_spin_lock+0x2f/0x40
usb_hcd_unlink_urb_from_ep+0x1b/0x60 [usbcore]
xhci_giveback_urb_in_irq.isra.45+0x70/0x1b0 [xhci_hcd]
finish_td.constprop.60+0x1d8/0x2e0 [xhci_hcd]
xhci_irq+0xdd6/0x1fa0 [xhci_hcd]
usb_hcd_irq+0x26/0x40 [usbcore]
irq_forced_thread_fn+0x2f/0x70
irq_thread+0x149/0x1d0
kthread+0x113/0x150
ret_from_fork+0x2e/0x40
This patch fixes the problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Bart Van Assche <bart.vanassche@sandisk.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to xHCI spec Figure 30: Interrupt Throttle Flow Diagram
If PCI Message Signaled Interrupts (MSI or MSI-X) are enabled,
then the assertion of the Interrupt Pending (IP) flag in Figure 30
generates a PCI Dword write. The IP flag is automatically cleared
by the completion of the PCI write.
the MSI enabled HCs don't need to clear interrupt pending bit, but
hcd->irq = 0 doesn't equal to MSI enabled HCD. At some Dual-role
controller software designs, it sets hcd->irq as 0 to avoid HCD
requesting interrupt, and they want to decide when to call usb_hcd_irq
by software.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to xHCI ch4.20 Scratchpad Buffers, the Scratchpad
Buffer needs to be zeroed.
...
The following operations take place to allocate
Scratchpad Buffers to the xHC:
...
b. Software clears the Scratchpad Buffer to '0'
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Denverton microserver is Atom based and need the PME and CAS quirks
as well.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't access any members of a URB after giving it back.
URB might be freed by then already.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unlike i.MX53, i.MX51's USBOH3 register file does not implemenent
registers past offset 0x018, which includes
MX53_USB_CLKONOFF_CTRL_OFFSET and trying to access that register on
said platform results in external abort.
Fix it by enabling CLKONOFF accessing codepath only for i.MX53.
Cc: stable <stable@vger.kernel.org>
Fixes 3be3251db0 ("usb: chipidea: imx: Disable internal 60Mhz
clock with ULPI PHY")
Cc: cphealy@gmail.com
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
If ci_hdrc_host_init() or ci_hdrc_gadget_init() returns error and the
error != -ENXIO, as Peter pointed out, "it stands for initialization
for host or gadget has failed", so we'd better return failure rather
continue.
And before destroying the otg, i.e ci_hdrc_otg_destroy(ci), we should
also check ci->roles[CI_ROLE_GADGET].
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
In their infinite wisdom, and never ending quest for end user frustration,
Lenovo has decided to use new USB device IDs for the wwan modules in
their 2017 laptops. The actual hardware is still the Sierra Wireless
EM7455 or EM7430, depending on region.
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
"ep->udc->lock" and "udc->lock" are the same thing. It confuses Smatch
if we don't use the same name consistently.
Reviewed-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds a quirk to disable USB 2.0 MAC linestate check
during HS transmit. Refer the dwc3 databook, we can use it for
some special platforms if the linestate not reflect the expected
line state(J) during transmission.
When use this quirk, the controller implements a fixed 40-bit
TxEndDelay after the packet is given on UTMI and ignores the
linestate during the transmit of a token (during token-to-token
and token-to-data IPGAP).
On some rockchip platforms (e.g. rk3399), it requires to disable
the u2mac linestate check to decrease the SSPLIT token to SETUP
token inter-packet delay from 566ns to 466ns, and fix the issue
that FS/LS devices not recognized if inserted through USB 3.0 HUB.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
