Synopsys introduces a new controller DWC_usb32. It supports dual-lane
and speed up to 20 Gbps, and the DWC3 driver will drive this controller.
Currently the driver uses a single field dwc->revision to ID both
DWC_usb3 and DWC_usb31 and their version number. This was sufficient for
two IPs, but this method doesn't work with additional IPs. As a result,
let's separate the dwc->revision field to 2 separate fields: ip and
revision. The ip field now stores the ID of the controller's IP while
the revision field stores the controller's version number.
This new scheme enforces DWC3 to compare the revision within the same IP
only. As a result, we must update all the revision check of the
controller to check its corresponding IP.
To help with this enforcement, we create a few macros to help with
the common version checks:
DWC3_IP_IS(IP)
DWC3_VER_IS(IP, VERSION)
DWC3_VER_IS_PRIOR(IP, VERSION)
DWC3_VER_IS_WITHIN(IP, LOWER_VERSION, UPPER_VERSION)
DWC3_VER_TYPE_IS_WITHIN(IP, VERSION,
LOWER_VERSION_TYPE,
UPPER_VERSION_TYPE)
The DWC_usb32 controller operates using the same programming model and
with very similar configurations as its previous controllers. Please
note that the various IP and revision checks in this patch match the
current checks for DWC_usb31 version 1.90a. Additional configurations
that are unique to DWC_usb32 are applied separately.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
OTG port on Tegra194 supports GEN1 speeds when in device mode and GEN2
speeds when in host mode. dd port_speed_quirk that configures port to
GEN1/GEN2 speds, corresponding to the mode.
Based on work by WayneChang <waynec@nvidia.com>
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This commit adds support for XUSB device mode controller support on
Tegra194 SoC. This is very similar to the existing Tegra186 XUDC, with lpm
support added in addition.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Sparse reports a warning at set_link_state()
warning: context imbalance in set_link_state() - unexpected unlock
The root cause is the missing annotation at set_link_state()
Add the missing __must_hold(&dum->lock)
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Sparse reports a warning at xudc_handle_setup()
warning: context imbalance in xudc_handle_setup() - unexpected unlock
The root cause is the missing annotation at xudc_handle_setup()
Add the missing __must_hold(&udc->lock) annotation
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
module_usb_composite_driver() makes the code simpler by
eliminating boilerplate code.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fix the following coccicheck warning:
drivers/usb/gadget/udc/omap_udc.c:2579:2-3: Unneeded semicolon
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fix the following coccicheck warning:
drivers/usb/gadget/udc/mv_u3d_core.c:1551:5-13: WARNING: Comparison to
bool
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fix the following coccicheck warning:
drivers/usb/gadget/udc/net2272.c:57:12-19: WARNING: Assignment of 0/1 to
bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fix the following coccicheck warning:
drivers/usb/dwc3/drd.c:85:3-24: WARNING: Assignment of 0/1 to bool
variable
drivers/usb/dwc3/drd.c:59:2-23: WARNING: Assignment of 0/1 to bool
variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The variable status is being assigned a value that is never read
and it is being updated later with a new value. The assignment
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Clang warns:
drivers/usb/gadget/udc/s3c2410_udc.c:255:11: warning: comparison of
address of 'ep->queue' equal to a null pointer is always false
[-Wtautological-pointer-compare]
if (&ep->queue == NULL)
~~~~^~~~~ ~~~~
1 warning generated.
It is not wrong, queue is not a pointer so if ep is not NULL, the
address of queue cannot be NULL. No other driver does a check like this
and this check has been around since the driver was first introduced,
presumably with no issues so it does not seem like this check should be
something else. Just remove it.
Commit afe956c577 ("kbuild: Enable -Wtautological-compare") exposed
this but it is not the root cause of the warning.
Fixes: 3fc154b6b8 ("USB Gadget driver for Samsung s3c2410 ARM SoC")
Link: https://github.com/ClangBuiltLinux/linux/issues/1004
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add suspend resume callbacks to notify u_serial of the bus suspend/resume
state.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add suspend resume callbacks to notify u_serial of the bus suspend/resume
state.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add suspend resume callbacks to handle the case seen when the bus is
suspended by the HOST, and the device opens the port (cat /dev/ttyGS0).
Gadget controller (like DWC2) doesn't accept usb requests to be queued in
this case (when in L2 state), from the gs_open() call. Error log is printed
- configfs-gadget gadget: acm ttyGS0 can't notify serial state, -11
If the HOST resumes (opens) the bus, the port still isn't functional.
Use suspend/resume callbacks to monitor the gadget suspended state by using
'suspended' flag. In case the port gets opened (cat /dev/ttyGS0), the I/O
stream will be delayed until the bus gets resumed by the HOST.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
When the remote wakeup interrupt is triggered, lx_state is resumed from L2
to L0 state. But when the gadget resume is called, lx_state is still L2.
This prevents the resume callback to queue any request. Any attempt
to queue a request from resume callback will result in:
- "submit request only in active state" debug message to be issued
- dwc2_hsotg_ep_queue() returns -EAGAIN
Call the gadget resume routine after the core is in L0 state.
Fixes: f81f46e1f5 ("usb: dwc2: implement hibernation during bus suspend/resume")
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch changes the function uvc_video_pump to be a separate
scheduled worker. This way the completion handler of each usb request
and every direct caller of the pump has only to schedule the worker
instead of doing the request handling by itself.
Moving the request handling to one thread solves the locking problems
between the three queueing cases in the completion handler, v4l2_qbuf
and video_enable.
Many drivers handle the completion handlers directly in their interrupt
handlers. This patch also reduces the workload on each interrupt.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch corrects the SPDX License Identifier style in
header files related to Renesas USBHS Controller Drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fix the following coccicheck warning:
drivers/usb/gadget/function/f_fs.c:2507:2-3: Unneeded semicolon
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
There is now a dedicated driver for these SoCs making the old compatible
obsolete.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
In order to add support for the Amlogic GXL/GXM USB Glue, this adds
the corresponding :
- PHY names
- clock names
- USB2 PHY init and mode set
- regmap setup
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
On the Amlogic GXL/GXM SoCs, the OTG PHY status signals are always
connected to the DWC3 controller, thus crashing the controller when
switching to OTG mode when port is not populated with a device/cable to
Host.
Amlogic added a bit to disconnect the OTG PHY status signals from the DWC3
to be used when switching the OTG PHY as Device to the DWC2 controller.
The drawback is that it makes the DWC3 port state machine stall and needs
a full reset of the DWC3 controller to get connect status to the port
connected to the OTG PHY, but not the other one.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Refactor the USB init code patch to handle the Amlogic GXL/GXM needing
to initialize the OTG port as Peripheral mode for the DWC2 IP to probe
correctly.
A secondary, post_init callback is added to setup the OTG PHY mode after
powering up the PHYs and before probing the DWC2 and DWC3 controllers.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fix the following gcc warning:
drivers/usb/gadget/udc/gr_udc.c:51:19: warning: ‘driver_desc’ defined
but not used [-Wunused-const-variable=]
static const char driver_desc[] = DRIVER_DESC;
^~~~~~~~~~~
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Message logged by 'dev_xxx()' or 'pr_xxx()' should end with a '\n'.
Fixes: 48ba02b2e2 ("usb: gadget: add udc driver for max3420")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch corrects the SPDX License Identifier style in
header files related to MediaTek USB3 Dual Role controller.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
During device mode initialization, lots of device information
are printed to console, see below. Change them as debug message.
cdns-usb3 5b130000.cdns3: Initialized ep0 support:
cdns-usb3 5b130000.cdns3: Initialized ep1out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep2out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep3out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep4out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep5out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep6out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep7out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep1in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep2in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep3in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep4in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep5in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep6in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep7in support: BULK, INT ISO
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
And delete cdsn3_hw_role_state_machine declare which doesn't
be needed.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
In short, we have three kinds of role switches:
- Based on SoC: ID and VBUS
- Based on external connnctor, eg, Type-C or GPIO Connector
- Based on user choices through sysfs
Since HW handling and usb-role-switch handling are at
different places, we do not need role_override any more,
and this flag could not judge external connector case well.
With role_override deleted, We use cdns3_hw_role_switch for
the 1st use case, and usb-role-switch for the 2nd and 3rd cases.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
After that, the role switch device (eg, Type-C device) could call
cdns3_role_set to finish the role switch.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If there are still pending requests because no TRB was available,
prepare more when started requests are completed.
Introduce dwc3_gadget_ep_should_continue() to check for incomplete and
pending requests to resume updating new TRBs to the controller's TRB
cache.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Register vbus_draw to gadget ops and update corresponding vbus
draw current to usb_phy.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
When I switched on USB role switching for the tps6598x I completely forgot
to add the Kconfig dependency.
Ensure USB_ROLE_SWITCH is selected to prevent the typs6598x driver being
compiled in but the role-switch driver being compiled as a module, leading
to link error.
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200520153617.610909-1-bryan.odonoghue@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function ehci_mxc_drv_probe() does not perform sufficient error
checking after executing platform_get_irq(), thus fix it.
Fixes: 7e8d5cd93f ("USB: Add EHCI support for MX27 and MX31 based boards")
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200513132647.5456-1-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The comparison of hcd->irq to less than zero for an error check will
never be true because hcd->irq is an unsigned int. Fix this by
assigning the int retval to the return of platform_get_irq and checking
this for the -ve error condition and assigning hcd->irq to retval.
Addresses-Coverity: ("Unsigned compared against 0")
Fixes: c856b4b0fd ("USB: EHCI: ehci-mv: fix error handling in mv_ehci_probe()")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200515165453.104028-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When renesas module is not built, we get compiler warning on xhci driver
with W=1
CC [M] drivers/usb/host/xhci-rcar.o
drivers/usb/host/xhci-pci.h:13:5: warning: no previous prototype for ‘renesas_xhci_check_request_fw’ [-Wmissing-prototypes]
int renesas_xhci_check_request_fw(struct pci_dev *dev,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/usb/host/xhci-pci.h:19:6: warning: no previous prototype for ‘renesas_xhci_pci_exit’ [-Wmissing-prototypes]
void renesas_xhci_pci_exit(struct pci_dev *dev) { };
^~~~~~~~~~~~~~~~~~~~~
We have defined these symbols when CONFIG_USB_XHCI_PCI_RENESAS is not
defined, but missed making then static.
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: 8bd5741e31 ("usb: renesas-xhci: Add the renesas xhci driver")
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200519093002.1152144-1-vkoul@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_wwan_indat_callback() shouldn't resubmit rx urb if the previous urb
status is a fatal error. Or the usb controller would keep processing the
new urbs then run into interrupt storm, and has no chance to recover.
Fixes: 6c1ee66a0b ("USB-Serial: Fix error handling of usb_wwan")
Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The xhci-pci-renesas module exports symbols for xhci-pci to load the
RAM/ROM on renesas xhci controllers. We had dependency which works
when both the modules are builtin or modules.
But if xhci-pci is inbuilt and xhci-pci-renesas in module, we get below
linker error:
drivers/usb/host/xhci-pci.o: In function `xhci_pci_remove':
drivers/usb/host/xhci-pci.c:411: undefined reference to `renesas_xhci_pci_exit'
drivers/usb/host/xhci-pci.o: In function `xhci_pci_probe':
drivers/usb/host/xhci-pci.c:345: undefined reference to `renesas_xhci_check_request_fw'
Fix this by adding USB_XHCI_PCI having depends on USB_XHCI_PCI_RENESAS
|| !USB_XHCI_PCI_RENESAS so that both can be either inbuilt or modules.
Reported-by: Anders Roxell <anders.roxell@linaro.org>
Fixes: a66d21d7db ("usb: xhci: Add support for Renesas controller with memory")
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200519050622.994908-1-vkoul@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
get_unaligned_le16() is defined in linux/unaligned/access_ok.h header
but it uses symbols which may not be available, leading to build
failures on ia64. Using asm/unaligned.h seem to be the right thing
and used in other drivers.
This fixes below error reported by kbuild test robot
In file included from drivers/usb/host/xhci-pci-renesas.c:9:
>> include/linux/unaligned/access_ok.h:8:28: error: redefinition of 'get_unaligned_le16'
8 | static __always_inline u16 get_unaligned_le16(const void *p)
| ^~~~~~~~~~~~~~~~~~
In file included from arch/ia64/include/asm/unaligned.h:5,
from arch/ia64/include/asm/io.h:23,
from arch/ia64/include/asm/smp.h:21,
from include/linux/smp.h:67,
from include/linux/percpu.h:7,
from include/linux/arch_topology.h:9,
from include/linux/topology.h:30,
from include/linux/gfp.h:9,
from include/linux/xarray.h:14,
from include/linux/radix-tree.h:18,
from include/linux/idr.h:15,
from include/linux/kernfs.h:13,
from include/linux/sysfs.h:16,
from include/linux/kobject.h:20,
from include/linux/of.h:17,
from include/linux/irqdomain.h:35,
from include/linux/acpi.h:13,
from drivers/usb/host/xhci-pci-renesas.c:4:
include/linux/unaligned/le_struct.h:7:19: note: previous definition of 'get_unaligned_le16' was here
7 | static inline u16 get_unaligned_le16(const void *p)
| ^~~~~~~~~~~~~~~~~~
In file included from drivers/usb/host/xhci-pci-renesas.c:9:
include/linux/unaligned/access_ok.h:13:28: error: redefinition of 'get_unaligned_le32'
13 | static __always_inline u32 get_unaligned_le32(const void *p)
| ^~~~~~~~~~~~~~~~~~
In file included from arch/ia64/include/asm/unaligned.h:5,
from arch/ia64/include/asm/io.h:23,
from arch/ia64/include/asm/smp.h:21,
from include/linux/smp.h:67,
from include/linux/percpu.h:7,
from include/linux/arch_topology.h:9,
from include/linux/topology.h:30,
from include/linux/gfp.h:9,
from include/linux/xarray.h:14,
from include/linux/radix-tree.h:18,
from include/linux/idr.h:15,
from include/linux/kernfs.h:13,
from include/linux/sysfs.h:16,
from include/linux/kobject.h:20,
from include/linux/of.h:17,
from include/linux/irqdomain.h:35,
from include/linux/acpi.h:13,
from drivers/usb/host/xhci-pci-renesas.c:4:
include/linux/unaligned/le_struct.h:12:19: note: previous definition of 'get_unaligned_le32' was here
Fixes: 8bd5741e31 ("usb: renesas-xhci: Add the renesas xhci driver")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200516162516.385149-1-vkoul@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uPD720201 supports ROM and allows software to program the ROM and boot
from it. Add support for detecting if ROM is present, if so load the ROM
if not programmed earlier.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200514122039.300417-5-vkoul@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some rensas controller like uPD720201 and uPD720202 need firmware to be
loaded. Add these devices in table and invoke renesas firmware loader
functions to check and load the firmware into device memory when
required.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200514122039.300417-4-vkoul@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This add a new driver for renesas xhci which is basically a firmware
loader for uPD720201 and uPD720202 w/o ROM. The xhci-pci driver will
invoke this driver for loading/unloading on relevant devices.
This patch adds a firmware loader for the uPD720201K8-711-BAC-A
and uPD720202K8-711-BAA-A variant. Both of these chips are listed
in Renesas' R19UH0078EJ0500 Rev.5.00 "User's Manual: Hardware" as
devices which need the firmware loader on page 2 in order to
work as they "do not support the External ROM".
The "Firmware Download Sequence" is describe in chapter
"7.1 FW Download Interface" R19UH0078EJ0500 Rev.5.00 page 131.
The firmware "K2013080.mem" is available from a USB3.0 Host to
PCIe Adapter (PP2U-E card) "Firmware download" archive. An
alternative version can be sourced from Netgear's WNDR4700 GPL
archives.
The release notes of the PP2U-E's "Firmware Download" ver 2.0.1.3
(2012-06-15) state that the firmware is for the following devices:
- uPD720201 ES 2.0 sample whose revision ID is 2.
- uPD720201 ES 2.1 sample & CS sample & Mass product, ID is 3.
- uPD720202 ES 2.0 sample & CS sample & Mass product, ID is 2.
[vkoul: fixed comments:
used macros for timeout count and delay
removed renesas_fw_alive_check
cleaned renesas_fw_callback
removed recursion for renesas_fw_download
add register defines and field names
move to a separate file
make fw loader as sync probe so that we execute in probe and
prevent race
make xhci-pci-renesas a seprate module]
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200514122039.300417-3-vkoul@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_hcd_pci_probe expects users to call this with driver_data set as
hc_driver, that limits the possibility of using the driver_data for
driver data.
Add hc_driver as argument to usb_hcd_pci_probe and modify the callers
ehci/ohci/xhci/uhci to pass hc_driver as argument and freeup the
driver_data used
Tested xhci driver on Dragon-board RB3, compile tested ehci, ohci and
uhci.
[For all but the xHCI parts]
[For the xhci part]
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200514122039.300417-2-vkoul@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
FuzzUSB (a variant of syzkaller) found an illegal array access
using an incorrect index while binding a gadget with UDC.
Reference: https://www.spinics.net/lists/linux-usb/msg194331.html
This bug occurs when a size variable used for a buffer
is misused to access its strcpy-ed buffer.
Given a buffer along with its size variable (taken from user input),
from which, a new buffer is created using kstrdup().
Due to the original buffer containing 0 value in the middle,
the size of the kstrdup-ed buffer becomes smaller than that of the original.
So accessing the kstrdup-ed buffer with the same size variable
triggers memory access violation.
The fix makes sure no zero value in the buffer,
by comparing the strlen() of the orignal buffer with the size variable,
so that the access to the kstrdup-ed buffer is safe.
BUG: KASAN: slab-out-of-bounds in gadget_dev_desc_UDC_store+0x1ba/0x200
drivers/usb/gadget/configfs.c:266
Read of size 1 at addr ffff88806a55dd7e by task syz-executor.0/17208
CPU: 2 PID: 17208 Comm: syz-executor.0 Not tainted 5.6.8 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xce/0x128 lib/dump_stack.c:118
print_address_description.constprop.4+0x21/0x3c0 mm/kasan/report.c:374
__kasan_report+0x131/0x1b0 mm/kasan/report.c:506
kasan_report+0x12/0x20 mm/kasan/common.c:641
__asan_report_load1_noabort+0x14/0x20 mm/kasan/generic_report.c:132
gadget_dev_desc_UDC_store+0x1ba/0x200 drivers/usb/gadget/configfs.c:266
flush_write_buffer fs/configfs/file.c:251 [inline]
configfs_write_file+0x2f1/0x4c0 fs/configfs/file.c:283
__vfs_write+0x85/0x110 fs/read_write.c:494
vfs_write+0x1cd/0x510 fs/read_write.c:558
ksys_write+0x18a/0x220 fs/read_write.c:611
__do_sys_write fs/read_write.c:623 [inline]
__se_sys_write fs/read_write.c:620 [inline]
__x64_sys_write+0x73/0xb0 fs/read_write.c:620
do_syscall_64+0x9e/0x510 arch/x86/entry/common.c:294
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Signed-off-by: Kyungtae Kim <kt0755@gmail.com>
Reported-and-tested-by: Kyungtae Kim <kt0755@gmail.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200510054326.GA19198@pizza01
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The main part here are the important fixes for the raw-gadget before it
becomes an ABI. We're adding support for stall/halt/wedge which is
actually pretty important in many situations. There's also a NULL
pointer deref fix.
Apart from raw-gadget, I've included some recent sparse fixes to a few
drivers.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
-----BEGIN PGP SIGNATURE-----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=0P11
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v5.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
USB: fixes for v5.7-rc6
The main part here are the important fixes for the raw-gadget before it
becomes an ABI. We're adding support for stall/halt/wedge which is
actually pretty important in many situations. There's also a NULL
pointer deref fix.
Apart from raw-gadget, I've included some recent sparse fixes to a few
drivers.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
* tag 'fixes-for-v5.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
usb: cdns3: gadget: make a bunch of functions static
usb: mtu3: constify struct debugfs_reg32
usb: gadget: udc: atmel: Make some symbols static
usb: raw-gadget: fix null-ptr-deref when reenabling endpoints
usb: raw-gadget: documentation updates
usb: raw-gadget: support stalling/halting/wedging endpoints
usb: raw-gadget: fix gadget endpoint selection
usb: raw-gadget: improve uapi headers comments
In commit 2bef9aed6f ("usb: usbfs: correct kernel->user page attribute
mismatch") we switched from always calling remap_pfn_range() to call
dma_mmap_coherent() to handle issues with systems with non-coherent USB host
controller drivers. Unfortunatly, as syzbot quickly told us, not all the world
is host controllers with DMA support, so we need to check what host controller
we are attempting to talk to before doing this type of allocation.
Thanks to Christoph for the quick idea of how to fix this.
Fixes: 2bef9aed6f ("usb: usbfs: correct kernel->user page attribute mismatch")
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hillf Danton <hdanton@sina.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jeremy Linton <jeremy.linton@arm.com>
Cc: stable <stable@vger.kernel.org>
Reported-by: syzbot+353be47c9ce21b68b7ed@syzkaller.appspotmail.com
Reviewed-by: Jeremy Linton <jeremy.linton@arm.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20200514112711.1858252-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On platforms with IOMMU enabled, multiple SGs can be coalesced into one
by the IOMMU driver. In that case the SG list processing as part of the
completion of a urb on a bulk endpoint can result into a NULL pointer
dereference with the below stack dump.
<6> Unable to handle kernel NULL pointer dereference at virtual address 0000000c
<6> pgd = c0004000
<6> [0000000c] *pgd=00000000
<6> Internal error: Oops: 5 [#1] PREEMPT SMP ARM
<2> PC is at xhci_queue_bulk_tx+0x454/0x80c
<2> LR is at xhci_queue_bulk_tx+0x44c/0x80c
<2> pc : [<c08907c4>] lr : [<c08907bc>] psr: 000000d3
<2> sp : ca337c80 ip : 00000000 fp : ffffffff
<2> r10: 00000000 r9 : 50037000 r8 : 00004000
<2> r7 : 00000000 r6 : 00004000 r5 : 00000000 r4 : 00000000
<2> r3 : 00000000 r2 : 00000082 r1 : c2c1a200 r0 : 00000000
<2> Flags: nzcv IRQs off FIQs off Mode SVC_32 ISA ARM Segment none
<2> Control: 10c0383d Table: b412c06a DAC: 00000051
<6> Process usb-storage (pid: 5961, stack limit = 0xca336210)
<snip>
<2> [<c08907c4>] (xhci_queue_bulk_tx)
<2> [<c0881b3c>] (xhci_urb_enqueue)
<2> [<c0831068>] (usb_hcd_submit_urb)
<2> [<c08350b4>] (usb_sg_wait)
<2> [<c089f384>] (usb_stor_bulk_transfer_sglist)
<2> [<c089f2c0>] (usb_stor_bulk_srb)
<2> [<c089fe38>] (usb_stor_Bulk_transport)
<2> [<c089f468>] (usb_stor_invoke_transport)
<2> [<c08a11b4>] (usb_stor_control_thread)
<2> [<c014a534>] (kthread)
The above NULL pointer dereference is the result of block_len and the
sent_len set to zero after the first SG of the list when IOMMU driver
is enabled. Because of this the loop of processing the SGs has run
more than num_sgs which resulted in a sg_next on the last SG of the
list which has SG_END set.
Fix this by check for the sg before any attributes of the sg are
accessed.
[modified reason for null pointer dereference in commit message subject -Mathias]
Fixes: f9c589e142 ("xhci: TD-fragment, align the unsplittable case with a bounce buffer")
Cc: stable@vger.kernel.org
Signed-off-by: Sriharsha Allenki <sallenki@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200514110432.25564-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following sparse warning:
drivers/usb/cdns3/gadget.c:85:6: warning: symbol
'cdns3_clear_register_bit' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:140:26: warning: symbol
'cdns3_next_align_buf' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:151:22: warning: symbol
'cdns3_next_priv_request' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:193:5: warning: symbol 'cdns3_ring_size' was
not declared. Should it be static?
drivers/usb/cdns3/gadget.c:348:6: warning: symbol
'cdns3_move_deq_to_next_trb' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:514:20: warning: symbol
'cdns3_wa2_gadget_giveback' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:554:5: warning: symbol
'cdns3_wa2_gadget_ep_queue' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:839:6: warning: symbol
'cdns3_wa1_restore_cycle_bit' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:1907:6: warning: symbol
'cdns3_stream_ep_reconfig' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:1928:6: warning: symbol
'cdns3_configure_dmult' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
mtu3_prb_regs is never changed and can therefore be made const.
This allows the compiler to put it in the text section instead of the
data section.
Before:
text data bss dec hex filename
19966 7120 0 27086 69ce drivers/usb/mtu3/mtu3_debugfs.o
After:
text data bss dec hex filename
20142 6992 0 27134 69fe drivers/usb/mtu3/mtu3_debugfs.o
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fix the following sparse warnings:
drivers/usb/gadget/udc/atmel_usba_udc.c:188:30: warning: symbol 'queue_dbg_fops' was not declared.
drivers/usb/gadget/udc/atmel_usba_udc.c:196:30: warning: symbol 'regs_dbg_fops' was not declared.
queue_dbg_fops and regs_dbg_fops have only call within atmel_usba_udc.c
They should be static
Fixes: 914a3f3b37 ("USB: add atmel_usba_udc driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Samuel Zou <zou_wei@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Currently we preassign gadget endpoints to raw-gadget endpoints during
initialization. Fix resetting this assignment in raw_ioctl_ep_disable(),
otherwise we will get null-ptr-derefs when an endpoint is reenabled.
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Raw Gadget is currently unable to stall/halt/wedge gadget endpoints,
which is required for proper emulation of certain USB classes.
This patch adds a few more ioctls:
- USB_RAW_IOCTL_EP0_STALL allows to stall control endpoint #0 when
there's a pending setup request for it.
- USB_RAW_IOCTL_SET/CLEAR_HALT/WEDGE allow to set/clear halt/wedge status
on non-control non-isochronous endpoints.
Fixes: f2c2e71764 ("usb: gadget: add raw-gadget interface")
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Currently automatic gadget endpoint selection based on required features
doesn't work. Raw Gadget tries iterating over the list of available
endpoints and finding one that has the right direction and transfer type.
Unfortunately selecting arbitrary gadget endpoints (even if they satisfy
feature requirements) doesn't work, as (depending on the UDC driver) they
might have fixed addresses, and one also needs to provide matching
endpoint addresses in the descriptors sent to the host.
The composite framework deals with this by assigning endpoint addresses
in usb_ep_autoconfig() before enumeration starts. This approach won't work
with Raw Gadget as the endpoints are supposed to be enabled after a
set_configuration/set_interface request from the host, so it's too late to
patch the endpoint descriptors that had already been sent to the host.
For Raw Gadget we take another approach. Similarly to GadgetFS, we allow
the user to make the decision as to which gadget endpoints to use.
This patch adds another Raw Gadget ioctl USB_RAW_IOCTL_EPS_INFO that
exposes information about all non-control endpoints that a currently
connected UDC has. This information includes endpoints addresses, as well
as their capabilities and limits to allow the user to choose the most
fitting gadget endpoint.
The USB_RAW_IOCTL_EP_ENABLE ioctl is updated to use the proper endpoint
validation routine usb_gadget_ep_match_desc().
These changes affect the portability of the gadgets that use Raw Gadget
when running on different UDCs. Nevertheless, as long as the user relies
on the information provided by USB_RAW_IOCTL_EPS_INFO to dynamically
choose endpoint addresses, UDC-agnostic gadgets can still be written with
Raw Gadget.
Fixes: f2c2e71764 ("usb: gadget: add raw-gadget interface")
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
According to the PMC Type C Subsystem (TCSS) Mux programming guide rev
0.6, the PMC HPD request LVL bit field is bit 4.
Fix the definition here to match the programming guide.
Since this bit field is changing, explicitly define a field for the
HPD_HIGH mode data bit.
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Fixes: 6701adfa96 ("usb: typec: driver for Intel PMC mux control")
Reviewed-by: Benson Leung <bleung@chromium.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200511091837.102508-1-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the build system changes needed to get the Broadcom STB XHCI,
EHCI and OHCI functionality working. The OHCI support does not
require anything unique to Broadcom so the standard ohci-platform
driver is being used. Also update MAINTAINERS.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20200512150019.25903-6-alcooperx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new EHCI driver for Broadcom STB SoC's. A new EHCI driver
was created instead of adding support to the existing ehci platform
driver because of the code required to work around bugs in the EHCI
controller. The primary workaround is for a bug where the Core
violates the SOF interval between the first two SOFs transmitted after
resume. This only happens if the resume occurs near the end of a
microframe. The fix is to intercept the ehci-hcd request to complete
RESUME and align it to the start of the next microframe.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200512150019.25903-5-alcooperx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for Broadcom STB SoC's to the xhci platform driver
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20200512150019.25903-4-alcooperx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds USB role switch support to the tps6598x.
The setup to initiate or accept a data-role switch is both assumed and
currently required to be baked-into the firmware as described in TI's
document here.
Link: https://www.ti.com/lit/an/slva843a/slva843a.pdf
With this change its possible to use the USB role-switch API to detect and
notify role-switches to downstream consumers.
Tested with a ChipIdea controller on a Qualcomm MSM8939.
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Nikolaus Voss <nikolaus.voss@loewensteinmedical.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Gustavo A. R. Silva <garsilva@embeddedor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20200511231930.2825183-2-bryan.odonoghue@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SBU and HSL orientation may be fixed/static from the mux
PoW. Apparently the retimer may take care of the orientation
of these lines. Handling the static SBU (AUX) and HSL
orientation with device properties.
If the SBU orientation is static, a device property
"sbu-orintation" can be used. When the property exists, the
driver always sets the SBU orientation according to the
property value, and when it's not set, the driver uses the
cable plug orientation with SBU.
And with static HSL orientation, "hsl-orientation" device
property can be used in the same way.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200507150900.12102-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Right now we don't report to user-space a role switch when doing a
usb_role_switch_set_role() despite having registered the uevent callbacks.
This patch switches on the notifications allowing user-space to see
role-switch change notifications and subsequently determine the current
controller data-role.
example:
PFX=/devices/platform/soc/78d9000.usb/ci_hdrc.0
root@somebox# udevadm monitor -p
KERNEL[49.894994] change $PFX/usb_role/ci_hdrc.0-role-switch (usb_role)
ACTION=change
DEVPATH=$PFX/usb_role/ci_hdrc.0-role-switch
SUBSYSTEM=usb_role
DEVTYPE=usb_role_switch
USB_ROLE_SWITCH=ci_hdrc.0-role-switch
SEQNUM=2432
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Wen Yang <wenyang@linux.alibaba.com>
Cc: chenqiwu <chenqiwu@xiaomi.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20200508162937.2566818-1-bryan.odonoghue@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 7d9e6f5aeb ("usb: host: ohci-sm501: init genalloc for local memory")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200506135625.106910-1-weiyongjun1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the function platform_get_irq() failed, the negative value
returned will not be detected here. So fix error handling in
mv_ehci_probe(). And when get irq failed, the function
platform_get_irq() logs an error message, so remove redundant
message here.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20200508114305.15740-1-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Delete unused initialized value, because 'retval' will be assigined
by the function mv_ehci_enable(). And delete the extra blank lines.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200508142136.4232-1-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the defined variable "dev" to make the code cleaner. And
delete an extra blank line.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200508144024.7836-1-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
scsi_get_host_dev() will create a virtual device such that either
the target id is ignored from scanning (if 'this_id' is set to
something which can be reached during scanning) or if the driver
needs a scsi device for the HBA to send commands to.
Neither is true for sierra-ms; 'this_id' remains at the default
value '-1' and the created device is never ever used within
the driver.
So kill it.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200505143019.57418-1-hare@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On the Raspberry Pi 4, after a PCI reset, VL805's firmware may either be
loaded directly from an EEPROM or, if not present, by the SoC's
VideoCore. Inform VideoCore that VL805 was just reset.
Also, as this creates a dependency between USB_PCI and VideoCore's
firmware interface, and since USB_PCI can't be set as a module neither
this can. Reflect that on the firmware interface Kconfg.
Link: https://lore.kernel.org/r/20200505161318.26200-5-nsaenzjulienne@suse.de
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
They must return the number of bytes transferred during the data stage.
Fixes: 068fbff4f8 ("usb: raw-gadget: Fix copy_to/from_user() checks")
Fixes: f2c2e71764 ("usb: gadget: add raw-gadget interface")
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Calling into the role switch API requires that these functions
are loaded, if they are in a loadable module and dwc3 itself
is built-in, this produces a link error:
drivers/usb/dwc3/drd.o: In function `dwc3_usb_role_switch_get':
drd.c:(.text+0x26): undefined reference to `usb_role_switch_get_drvdata'
drivers/usb/dwc3/drd.o: In function `dwc3_usb_role_switch_set':
drd.c:(.text+0x97): undefined reference to `usb_role_switch_get_drvdata'
drivers/usb/dwc3/drd.o: In function `dwc3_drd_init':
drd.c:(.text+0x1ca7): undefined reference to `usb_role_switch_register'
drivers/usb/dwc3/drd.o: In function `dwc3_drd_exit':
drd.c:(.text+0x1e92): undefined reference to `usb_role_switch_unregister'
Select the USB_ROLE_SWITCH symbol from dwc3 in that configuration.
Fixes: 0339f7fbc8 ("usb: dwc3: fix up for role switch API change")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If 'usb_otg_descriptor_alloc()' fails, we must return a
negative error code -ENOMEM, not 0.
Fixes: 1156e91dd7 ("usb: gadget: ncm: allocate and init otg descriptor by otg capabilities")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If 'usb_otg_descriptor_alloc()' fails, we must return a
negative error code -ENOMEM, not 0.
Fixes: ab6796ae98 ("usb: gadget: cdc2: allocate and init otg descriptor by otg capabilities")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fix the following cppcheck warnings:
drivers/usb/gadget/legacy/inode.c:1364:8: style: Redundant initialization for 'value'. The initialized value is overwritten$
value = -EOPNOTSUPP;
^
drivers/usb/gadget/legacy/inode.c:1331:15: note: value is initialized
int value = -EOPNOTSUPP;
^
drivers/usb/gadget/legacy/inode.c:1364:8: note: value is overwritten
value = -EOPNOTSUPP;
^
drivers/usb/gadget/legacy/inode.c:1817:8: style: Redundant initialization for 'value'. The initialized value is overwritten$
value = -EINVAL;
^
drivers/usb/gadget/legacy/inode.c:1787:18: note: value is initialized
ssize_t value = len, length = len;
^
drivers/usb/gadget/legacy/inode.c:1817:8: note: value is overwritten
value = -EINVAL;
^
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
When the XUDC device is idle (i.e. powergated), care must be taken not
to access any registers because that would lead to a crash.
Move the call to tegra_xudc_device_mode_off() into the same conditional
as the tegra_xudc_powergate() call to make sure we only force device
mode off if the XUDC is actually powered up.
Fixes: 49db427232 ("usb: gadget: Add UDC driver for tegra XUSB device mode controller")
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
'dev' is allocated in 'net2272_probe_init()'. It must be freed in the error
handling path, as already done in the remove function (i.e.
'net2272_plat_remove()')
Fixes: 90fccb529d ("usb: gadget: Gadget directory cleanup - group UDC drivers")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
A call to 'regulator_get()' is hidden in 'twl6030_usb_ldo_init()'. A
corresponding put must be performed in the error handling path, as
already done in the remove function.
While at it, also move a 'free_irq()' call in the error handling path in
order to be consistent.
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If 'usb_otg_descriptor_alloc()' fails, we must return an error code, not 0.
Fixes: 56023ce0fd ("usb: gadget: audio: allocate and init otg descriptor by otg capabilities")
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Intel Merrifield provides a DR support via PMIC which has its own
extcon driver.
Add a property string to link to that driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The check for the HWO flag in dwc3_gadget_ep_reclaim_trb_sg()
causes us to break out of the loop before we call
dwc3_gadget_ep_reclaim_completed_trb(), which is what likely
should be clearing the HWO flag.
This can cause odd behavior where we never reclaim all the trbs
in the sg list, so we never call giveback on a usb req, and that
will causes transfer stalls.
This effectively resovles the adb stalls seen on HiKey960
after userland changes started only using AIO in adbd.
Cc: YongQin Liu <yongqin.liu@linaro.org>
Cc: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Cc: Yang Fei <fei.yang@intel.com>
Cc: Thinh Nguyen <thinhn@synopsys.com>
Cc: Tejas Joglekar <tejas.joglekar@synopsys.com>
Cc: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: Josh Gao <jmgao@google.com>
Cc: Todd Kjos <tkjos@google.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: stable@vger.kernel.org #4.20+
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Currently we check to make sure there is no error state on the extcon
handle for VBUS when writing to the HS_PHY_GENCONFIG_2 register. When using
the USB role-switch API we still need to write to this register absent an
extcon handle.
This patch makes the appropriate update to ensure the write happens if
role-switching is true.
Fixes: 05559f10ed ("usb: chipidea: add role switch class support")
Cc: stable <stable@vger.kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200507004918.25975-2-peter.chen@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's a fix adding a missing input sanity check and a new modem device
id.
Both have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXrLNGgAKCRALxc3C7H1l
CL9cAQDKplqMiVKST+Zmkj4tWjNT1cyCaUd0Ph5A6G5c3mp9KAD9FVmA8hs2ZJCe
5EbgjBaQaKcoRCTb+Gu2OZxX3AIt3ww=
=0Lm7
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.7-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.7-rc5
Here's a fix adding a missing input sanity check and a new modem device
id.
Both have been in linux-next with no reported issues.
* tag 'usb-serial-5.7-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: qcserial: Add DW5816e support
USB: serial: garmin_gps: add sanity checking for data length
The flag provided by the USB role-switch logic allow_userspace_control
allows user-space to trigger a role-switch. Several other USB controller
drivers already enable this feature. Let's switch it on for the chipidea
core now also.
Cc: Peter Chen <Peter.Chen@nxp.com>
Cc: Jun Li <jun.li@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
imx7ulp uses different USB PHY with imx7d (MXS PHY vs PICO PHY), so the
features are supported by non-core register are a little different.
For example, autoresume feature is supported by all controllers for
imx7ulp, but for imx7d, it is only supported by non-HSIC controller.
Besides, these two platforms use different HSIC controller, imx7ulp
needs software operation, but imx7d doesn't.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The bootloader may use device mode, and keep dp up. We need dp
to be pulled down before possbile charger detection operation.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
imx7d (and imx8mm, imx8mn) uses Samsung PHY and USB generic PHY driver.
The USB generic PHY driver is impossible to have a charger detection
for every user, so we implement USB charger detection routine at glue
layer. After the detection has finished, it will notify USB PHY
charger framework, and the uevents will be triggered.
Signed-off-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Some vendors glue layer need to handle some events for vbus, eg,
some i.mx platforms (imx7d, imx8mm, imx8mn, etc) needs vbus event
to handle charger detection, its charger detection is finished at
glue layer code, but not at USB PHY driver.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
According to the PMC Type C Subsystem (TCSS) Mux programming guide rev
0.6, when a device is transitioning to DP Alternate Mode state, if the
HPD_STATE (bit 7) field in the status update command VDO is set to
HPD_HIGH, the HPD_HIGH field in the Alternate Mode request “mode_data”
field (bit 14) should also be set. Ensure the bit is correctly handled
while issuing the Alternate Mode request.
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Fixes: 6701adfa96 ("usb: typec: driver for Intel PMC mux control")
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200429054432.134178-1-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some architectures (e.g. arm64) requests for
IO coherent memory may use non-cachable attributes if
the relevant device isn't cache coherent. If these
pages are then remapped into userspace as cacheable,
they may not be coherent with the non-cacheable mappings.
In particular this happens with libusb, when it attempts
to create zero-copy buffers for use by rtl-sdr
(https://github.com/osmocom/rtl-sdr/). On low end arm
devices with non-coherent USB ports, the application will
be unexpectedly killed, while continuing to work fine on
arm machines with coherent USB controllers.
This bug has been discovered/reported a few times over
the last few years. In the case of rtl-sdr a compile time
option to enable/disable zero copy was implemented to
work around it.
Rather than relaying on application specific workarounds,
dma_mmap_coherent() can be used instead of remap_pfn_range().
The page cache/etc attributes will then be correctly set in
userspace to match the kernel mapping.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200504201348.1183246-1-jeremy.linton@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device property names for the port index number are
"usb2-port-number" and "usb3-port-number", not "usb2-port"
and "usb3-port".
Fixes: 6701adfa96 ("usb: typec: driver for Intel PMC mux control")
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200430135657.45169-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The syzbot fuzzer found a race between URB submission to endpoint 0
and device reset. Namely, during the reset we call usb_ep0_reinit()
because the characteristics of ep0 may have changed (if the reset
follows a firmware update, for example). While usb_ep0_reinit() is
running there is a brief period during which the pointers stored in
udev->ep_in[0] and udev->ep_out[0] are set to NULL, and if an URB is
submitted to ep0 during that period, usb_urb_ep_type_check() will
report it as a driver bug. In the absence of those pointers, the
routine thinks that the endpoint doesn't exist. The log message looks
like this:
------------[ cut here ]------------
usb 2-1: BOGUS urb xfer, pipe 2 != type 2
WARNING: CPU: 0 PID: 9241 at drivers/usb/core/urb.c:478
usb_submit_urb+0x1188/0x1460 drivers/usb/core/urb.c:478
Now, although submitting an URB while the device is being reset is a
questionable thing to do, it shouldn't count as a driver bug as severe
as submitting an URB for an endpoint that doesn't exist. Indeed,
endpoint 0 always exists, even while the device is in its unconfigured
state.
To prevent these misleading driver bug reports, this patch updates
usb_disable_endpoint() to avoid clearing the ep_in[] and ep_out[]
pointers when the endpoint being disabled is ep0. There's no danger
of leaving a stale pointer in place, because the usb_host_endpoint
structure being pointed to is stored permanently in udev->ep0; it
doesn't get deallocated until the entire usb_device structure does.
Reported-and-tested-by: syzbot+db339689b2101f6f6071@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2005011558590.903-100000@netrider.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the driver issued START_TRANSFER and received a no-resource status,
then generally there are a few reasons for this:
1) The driver did not allocate resource for the endpoint during
power-on-reset initialization.
2) The transfer resource was reset. At this moment, we don't do this in
the driver, but it occurs when the driver issues START_CONFIG cmd to ep0
with resource index=2.
3) The driver issues the START_TRANSFER command to an already started
endpoint. Usually, this is because the END_TRANSFER command hasn't
completed yet.
Print out a warning to help debug this issue in the driver.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
After a number of unsuccessful start isoc attempts due to bus-expiry
status, issue END_TRANSFER command and retry on the next XferNotReady
event.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
As long as the START_TRANSFER command completes, it provides the
resource index of the endpoint. Use this when we need to issue
END_TRANSFER command to an isoc endpoint to retry with a new
XferNotReady event.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If dwc3 fails to issue START_TRANSFER/UPDATE_TRANSFER command, then we
should properly end an active transfer and give back all the started
requests. However if it's for an isoc endpoint, the failure maybe due to
bus-expiry status. In this case, don't give back the requests and wait
for the next retry.
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If the driver is configured to use DRD role-switch, let the drd code
path decide the default dr_mode.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If the driver is configured to use DRD role-switch, it's not OTG. There
won't be OTG irq to free. Check for dwc->otg_irq before freeing it.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Refactor the USB2 PHY init code patch to handle the Amlogic GXL/GXM
not having the PHY mode control registers in the Glue but in the PHY
registers.
The Amlogic GXL/GXM will call phy_set_mode() instead of programming the
PHY mode control registers, thus add two new callbacks to the SoC match
data.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The dwc3_meson_g12a_usb_init function can return an error, check it.
Fixes: c99993376f ("usb: dwc3: Add Amlogic G12A DWC3 glue")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
In order to support the Amlogic GXL/GXM SoCs, the reset line must
be handled as shared since also used by the PHYs.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
On the Amlogic GXL/GXM SoCs, only the USB control registers are available,
the PHY mode being handled in the PHY registers.
Thus, handle the PHY mode registers in separate regmaps and prepare
support for Amlogic GXL/GXM SoCs by moving the regmap setup in a callback
set in the SoC match data.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
To handle the variable USB2 PHY counts on GXL and GXM SoCs, add the
possible PHY names for each SoC in the compatible match data.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Hanjie Lin <hanjie.lin@amlogic.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The flow from function dwc3_gadget_ep_dequeue() is not easy to follow.
Refactor it for easier read. No functional change in this commit.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Remove 2 unnecessary checks:
1) A request in the started_list must have its trb field set. So
checking for req->trb is unnecessary.
2) An endpoint must have started (and have not ended) for the request to
still be in the started_list. There's no point to check if the endpoint
is started. We had this check because previously the driver didn't
handle the endpoint's started/ended flags for END_TRANSFER command
properly. See commit 9f45581f5e ("usb: dwc3: gadget: early giveback
if End Transfer already completed").
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If a request is dequeued, the transfer is cancelled. Give back all
the started requests.
In most scenarios, the function driver dequeues all requests of a
transfer when there's a failure. If the function driver follows this,
then it's fine. If not, then we'd be skipping TRBs at different points
within the dequeue and enqueue pointers, making dequeue/enqueue pointers
useless. To enforce and make sure that we're properly skipping TRBs,
cancel all the started requests and give back all the cancelled requests
to the function drivers.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
DWC3 must not issue CLEAR_STALL command to control endpoints. The
controller automatically clears the STALL when it receives the SETUP
token. Also, when the driver receives ClearFeature(halt_ep), DWC3 must
stop any active transfer from the endpoint and give back all the
requests to the function drivers.
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch moves patch-usb1-dev-desc logic from get-descriptor handler
to "ast_vhub_fixup_usb1_dev_desc" function so the code is executed only
once (at vhub initial time).
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The patch overrides idVendor, idProduct and bcdDevice fields in vhub
Device Descriptor if according device tree properties are defined.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If "vhub,string-descriptor" device tree property is defined, the driver
will load string descriptors from device tree; otherwise, the default
string descriptors will be used.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The USB LANGID validation code in "check_user_usb_string" function is
moved to "usb_validate_langid" function which can be used by other usb
gadget drivers.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch introduces a link list to store string descriptors with
different languages, and "ast_vhub_rep_string" function is also improved
to support multiple language usb strings.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch evaluates vhub ports' irq mask before going through per-port
irq handling one by one, which helps to speed up irq handling in case
there is no port interrupt.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The DRD module calls dwc3_set_mode() on role switches, i.e. when a device is
being plugged in. In order to support continuous runtime power management when
plugging in / unplugging a cable, we need to call pm_runtime_get_sync() in
this path.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Mark all local functions static to fix sparse warnings.
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch corrects the SPDX License Identifier style in
header files related to DesignWare USB2 DRD Core Support.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch corrects the SPDX License Identifier style in
header files related to DesignWare USB3 DRD Core Support.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch corrects the SPDX License Identifier style in
header files related to USB peripheral controller drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add support for Dell Wireless 5816e to drivers/usb/serial/qcserial.c
Signed-off-by: Matt Jolly <Kangie@footclan.ninja>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix the following coccicheck warning:
drivers/usb/chipidea/ci_hdrc_usb2.c:75:28-29: Unneeded semicolon
Fixes: c2de37b31f ("usb: chipidea: usb2: make clock optional")
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Fix the following coccicheck warning:
drivers/usb/core/hub.c:95:12-28: WARNING: Assignment of 0/1 to bool
variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Link: https://lore.kernel.org/r/20200426094147.23467-1-yanaijie@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The stub was ucsi_register_port() when it should have been
ucsi_register_port_psy().
Cc: Abhilash K V <abhilash.k.v@intel.com>
Fixes: 992a60ed0d ("usb: typec: ucsi: register with power_supply class")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200427111246.4889-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver only creates a bunch of platform devices sharing resources
belonging to the PMC device. This is pretty much what MFD subsystem is
for so move the driver there, renaming it to intel_pmc_bxt.c which
should be more clear what it is.
MFD subsystem provides nice helper APIs for subdevice creation so
convert the driver to use those. Unfortunately the ACPI device includes
separate resources for most of the subdevices so we cannot simply call
mfd_add_devices() to create all of them but instead we need to call it
separately for each device.
The new MFD driver continues to expose two sysfs attributes that allow
userspace to send IPC commands to the PMC/SCU to avoid breaking any
existing applications that may use these. Generally this is bad idea so
document this in the ABI documentation.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Convert the driver to use the new SCU IPC API. This allows us to get rid
of the duplicate PMC IPC implementation which is now covered in SCU IPC
driver.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
With this change the UCSI device will show up in
/sys/class/power_supply/. The following values are exported:
- online
- usb_type
- voltage_min
- voltage_max
- voltage_now
- current_max
- current_now
Once a PD-capable type-C power source is connected to the system, GET_PDOS
UCSI command is used to query all source capabilities. Request data object
(RDO) is used to get current values.
Signed-off-by: K V, Abhilash <abhilash.k.v@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200423132058.6972-7-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When connected to a PD-capable power-source, read & save all partner
power data objects (PDOs) by using GET_PDOS UCSI command.
Also, save the current power contract in request data object (RDO)
for that connector.
Signed-off-by: K V, Abhilash <abhilash.k.v@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200423132058.6972-6-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bit 0 is reserved in CCI (Command Status & Connector Change Indicator)
register. So, change bit-mask for connector number field to 7..1
instead of 7..0.
There would be no functional change since we were anyways right-shifing
by 1 bit.
Signed-off-by: K V, Abhilash <abhilash.k.v@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200423132058.6972-5-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
EC firmware on Dell XPS & Latitude series does not set "Power Operation
Mode Change" bit in "Connector Status change" field of MESSAGE IN Data
while transitioning from type-C current to PD mode.
Instead the "Negotiated Power Level Change" bit is set when the "Power
Operation Mode" field shows the correct mode (i.e. PD).
This patch adds a check for this bit also, to trigger an update of
power operation mode in class driver, while handling GET_CONNECTOR_STATUS
command.
Signed-off-by: K V, Abhilash <abhilash.k.v@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200423132058.6972-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently UCSI framework doesn't update USB data role when partner type
is reported as power cable or power cable with ufp connected. This
results into no USB host mode functionality. This is valid usecase where
user wants to use legacy type c power cable with type a female connector
to attach different USB devices like mouse, thumb drive etc. Hence update
USB data role as host when partner type is reported as power cable or
power cable with ufp connected.
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200423132058.6972-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following gcc warning:
drivers/usb/gadget/udc/gr_udc.c:51:19: warning: ‘driver_desc’ defined
but not used [-Wunused-const-variable=]
static const char driver_desc[] = DRIVER_DESC;
^~~~~~~~~~~
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Link: https://lore.kernel.org/r/20200417073137.39968-1-yanaijie@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the SPDX License Identifier style in
header files related to Physical Layer USB driver configuration.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Link: https://lore.kernel.org/r/20200419123559.GA4505@nishad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the SPDX License Identifier style in
header files related to Renesas USBHS Controller Drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200419125705.GA5172@nishad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the SPDX License Identifier style in
header files related to USB Storage driver configuration.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Link: https://lore.kernel.org/r/20200419131653.GA6611@nishad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the SPDX License Identifier style in
header file related to USB Type-C support.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Reviewed-by Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200419133051.GA7154@nishad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following coccicheck warning:
drivers/usb/host/pci-quirks.c:532:1-27: WARNING: Assignment of 0/1 to
bool variable
drivers/usb/host/pci-quirks.c:208:1-20: WARNING: Assignment of 0/1 to
bool variable
drivers/usb/host/pci-quirks.c:232:2-21: WARNING: Assignment of 0/1 to
bool variable
drivers/usb/host/pci-quirks.c:235:2-21: WARNING: Assignment of 0/1 to
bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Link: https://lore.kernel.org/r/20200420042622.18564-1-yanaijie@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a dev_dbg() message to usb_create_sysfs_intf_files().
The message is not expected ever to appear; it's real purpose is to
satisfy the __must_check attribute on device_create_file() without
triggering a compiler warning about an empty statement.
In fact we don't really care if the sysfs attribute file doesn't get
created. The interface string descriptor is purely informational and
hardly ever present.
Suggested-by: NeilBrown <neilb@suse.de>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2004221618500.11262-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following versioncheck warning:
drivers/usb/early/xhci-dbc.c:21:1: unused including <linux/version.h>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Link: https://lore.kernel.org/r/20200421033945.27703-1-yanaijie@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change a bunch of arguments of wrapper functions which pass signed
integer to an unsigned integer which might cause undefined behaviors
when sign integer overflow.
Signed-off-by: Changming Liu <liu.changm@northeastern.edu>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/BL0PR06MB45482D71EA822D75A0E60A2EE5D50@BL0PR06MB4548.namprd06.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cyril Roelandt reports that his JMicron JMS566 USB-SATA bridge fails
to handle WRITE commands with the FUA bit set, even though it claims
to support FUA. (Oddly enough, a later version of the same bridge,
version 2.03 as opposed to 1.14, doesn't claim to support FUA. Also
oddly, the bridge _does_ support FUA when using the UAS transport
instead of the Bulk-Only transport -- but this device was blacklisted
for uas in commit bc3bdb12bb ("usb-storage: Disable UAS on JMicron
SATA enclosure") for apparently unrelated reasons.)
This patch adds a usb-storage unusual_devs entry with the BROKEN_FUA
flag. This allows the bridge to work properly with usb-storage.
Reported-and-tested-by: Cyril Roelandt <tipecaml@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2004221613110.11262-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit bd0e6c9614 ("usb: hub: try old enumeration scheme first for
high speed devices") changed the way the hub driver enumerates
high-speed devices. Instead of using the "new" enumeration scheme
first and switching to the "old" scheme if that doesn't work, we start
with the "old" scheme. In theory this is better because the "old"
scheme is slightly faster -- it involves resetting the device only
once instead of twice.
However, for a long time Windows used only the "new" scheme. Zeng Tao
said that Windows 8 and later use the "old" scheme for high-speed
devices, but apparently there are some devices that don't like it.
William Bader reports that the Ricoh webcam built into his Sony Vaio
laptop not only doesn't enumerate under the "old" scheme, it gets hung
up so badly that it won't then enumerate under the "new" scheme! Only
a cold reset will fix it.
Therefore we will revert the commit and go back to trying the "new"
scheme first for high-speed devices.
Reported-and-tested-by: William Bader <williambader@hotmail.com>
Ref: https://bugzilla.kernel.org/show_bug.cgi?id=207219
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: bd0e6c9614 ("usb: hub: try old enumeration scheme first for high speed devices")
CC: Zeng Tao <prime.zeng@hisilicon.com>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2004221611230.11262-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8099f58f1e ("USB: hub: Don't record a connect-change event
during reset-resume") wasn't very well conceived. The problem it
tried to fix was that if a connect-change event occurred while the
system was asleep (such as a device disconnecting itself from the bus
when it is suspended and then reconnecting when it resumes)
requiring a reset-resume during the system wakeup transition, the hub
port's change_bit entry would remain set afterward. This would cause
the hub driver to believe another connect-change event had occurred
after the reset-resume, which was wrong and would lead the driver to
send unnecessary requests to the device (which could interfere with a
firmware update).
The commit tried to fix this by not setting the change_bit during the
wakeup. But this was the wrong thing to do; it means that when a
device is unplugged while the system is asleep, the hub driver doesn't
realize anything has happened: The change_bit flag which would tell it
to handle the disconnect event is clear.
The commit needs to be reverted and the problem fixed in a different
way. Fortunately an alternative solution was noted in the commit's
Changelog: We can continue to set the change_bit entry in
hub_activate() but then clear it when a reset-resume occurs. That way
the the hub driver will see the change_bit when a device is
disconnected but won't see it when the device is still present.
That's what this patch does.
Reported-and-tested-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: 8099f58f1e ("USB: hub: Don't record a connect-change event during reset-resume")
Tested-by: Paul Zimmerman <pauldzim@gmail.com>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2004221602480.11262-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the SPDX License Identifier style in
header files related to USB Serial device configuration.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
We must not process packets shorter than a packet ID
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-and-tested-by: syzbot+d29e9263e13ce0b9f4fd@syzkaller.appspotmail.com
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The default control endpoint ep0 can return a STALL indicating the
device does not support the control transfer requests. This is called
a protocol stall and does not halt the endpoint.
xHC behaves a bit different. Its internal endpoint state will always
be halted on any stall, even if the device side of the endpiont is not
halted. So we do need to issue the reset endpoint command to clear the
xHC host intenal endpoint halt state, but should not request the HS hub
to clear the TT buffer unless device side of endpoint is halted.
Clearing the hub TT buffer at protocol stall caused ep0 to become
unresponsive for some FS/LS devices behind HS hubs, and class drivers
failed to set the interface due to timeout:
usb 1-2.1: 1:1: usb_set_interface failed (-110)
Fixes: ef513be0a9 ("usb: xhci: Add Clear_TT_Buffer")
Cc: <stable@vger.kernel.org> # v5.3
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200421140822.28233-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspending the bus and host controller while a port is in a over-current
condition may halt the host.
Also keep the roothub running if over-current is active.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200421140822.28233-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a class driver cancels its only URB then the endpoint ring buffer will
appear empty to the xhci driver. xHC hardware may still process cached
TRBs, and complete with a STALL, halting the endpoint.
This halted endpoint was not handled correctly by xhci driver as events on
empty rings were all assumed to be spurious events.
xhci driver refused to restart the ring with EP_HALTED flag set, so class
driver was never informed the endpoint halted even if it queued new URBs.
The host side of the endpoint needs to be reset, and dequeue pointer should
be moved in order to clear the cached TRBs and resetart the endpoint.
Small adjustments in finding the new dequeue pointer are needed to support
the case of stall on an empty ring and unknown current TD.
Cc: <stable@vger.kernel.org>
cc: Jeremy Compostella <jeremy.compostella@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200421140822.28233-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DWC3 learns how to properly set maxpacket limit and got a fix for a
request completion bug. The raw gadget got a fix for
copy_to/from_user() checks. Atmel got an improvement on vbus
disconnect handling.
We're also adding support for another SoC to the Renesas DRD driver.
-----BEGIN PGP SIGNATURE-----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=lK94
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v5.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
USB: fixes for v5.7-rc2
DWC3 learns how to properly set maxpacket limit and got a fix for a
request completion bug. The raw gadget got a fix for
copy_to/from_user() checks. Atmel got an improvement on vbus
disconnect handling.
We're also adding support for another SoC to the Renesas DRD driver.
* tag 'fixes-for-v5.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
usb: raw-gadget: Fix copy_to/from_user() checks
usb: raw-gadget: fix raw_event_queue_fetch locking
usb: gadget: udc: atmel: Fix vbus disconnect handling
usb: dwc3: gadget: Fix request completion check
usb: dwc3: gadget: Do link recovery for SS and SSP
dt-bindings: usb: renesas,usb3-peri: add r8a77961 support
dt-bindings: usb: renesas,usbhs: add r8a77961 support
dt-bindings: usb: usb-xhci: add r8a77961 support
docs: dt: qcom,dwc3.txt: fix cross-reference for a converted file
usb: dwc3: gadget: Properly set maxpacket limit
usb: dwc3: Fix GTXFIFOSIZ.TXFDEP macro name
usb: gadget: udc: bdc: Remove unnecessary NULL checks in bdc_req_complete
The copy_to/from_user() functions return the number of bytes remaining
but we want to return negative error codes. I changed a couple checks
in raw_ioctl_ep_read() and raw_ioctl_ep0_read() to show that we still
we returning zero on error.
Fixes: f2c2e71764 ("usb: gadget: add raw-gadget interface")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If queue->size check in raw_event_queue_fetch() fails (which normally
shouldn't happen, that check is a fail-safe), the function returns
without reenabling interrupts. This patch fixes that issue, along with
propagating the cause of failure to the function caller.
Fixes: f2c2e71764 ("usb: gadget: add raw-gadget interface"
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
A DMA transfer can be in progress while vbus is lost due to a cable
disconnect. For endpoints that use DMA, this condition can lead to
peripheral hang. The patch ensures that endpoints are disabled before
the clocks are stopped to prevent this issue.
Fixes: a64ef71ddc ("usb: gadget: atmel_usba_udc: condition clocks to vbus state")
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
A request may not be completed because not all the TRBs are prepared for
it. This happens when we run out of available TRBs. When some TRBs are
completed, the driver needs to prepare the rest of the TRBs for the
request. The check dwc3_gadget_ep_request_completed() shouldn't be
checking the amount of data received but rather the number of pending
TRBs. Revise this request completion check.
Cc: stable@vger.kernel.org
Fixes: e0c42ce590 ("usb: dwc3: gadget: simplify IOC handling")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fix the following sparse warning:
drivers/usb/cdns3/gadget.c:85:6: warning: symbol
'cdns3_clear_register_bit' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:140:26: warning: symbol
'cdns3_next_align_buf' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:151:22: warning: symbol
'cdns3_next_priv_request' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:193:5: warning: symbol 'cdns3_ring_size' was
not declared. Should it be static?
drivers/usb/cdns3/gadget.c:348:6: warning: symbol
'cdns3_move_deq_to_next_trb' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:514:20: warning: symbol
'cdns3_wa2_gadget_giveback' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:554:5: warning: symbol
'cdns3_wa2_gadget_ep_queue' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:839:6: warning: symbol
'cdns3_wa1_restore_cycle_bit' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:1907:6: warning: symbol
'cdns3_stream_ep_reconfig' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:1928:6: warning: symbol
'cdns3_configure_dmult' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200402123837.5850-1-yanaijie@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the FUSB302 driver to use GPIO descriptors.
The conversion to descriptors per se is pretty straight-forward.
In the process I discovered that:
1. The driver uses a completely undocumented device tree binding
for the interrupt GPIO line, "fcs,int_n". Ooops.
2. The undocumented binding, presumably since it has not seen
review, is just "fcs,int_n", lacking the compulsory "-gpios"
suffix and also something that is not a good name because
the "_n" implies the line is inverted which is something we
handle with flags in the device tree. Ooops.
3. Possibly the driver should not be requesting the line as a
GPIO and request the corresponding interrupt line by open
coding, the GPIO chip is very likely doubleing as an IRQ
controller and can probably provide an interrupt directly
for this line with interrupts-extended = <&gpio0 ...>;
4. Possibly the IRQ should just be tagged on the I2C client node
in the device tree like apparently ACPI does, as it overrides
this IRQ with client->irq if that exists.
But now it is too late to do much about that and as I can see
this is used like this in the Pinebook which is a shipping product
so let'a just contain the mess and move on.
The property currently appears in:
arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts
Create a quirk in the GPIO OF library to allow this property
specifically to be specified without the "-gpios" suffix, we have
other such bindings already.
Cc: Tobias Schramm <t.schramm@manjaro.org>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Yueyao Zhu <yueyao@google.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: devicetree@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200415192448.305257-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During device mode initialization, lots of device information
are printed to console, see below. Change them as debug message.
cdns-usb3 5b130000.cdns3: Initialized ep0 support:
cdns-usb3 5b130000.cdns3: Initialized ep1out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep2out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep3out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep4out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep5out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep6out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep7out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep1in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep2in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep3in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep4in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep5in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep6in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep7in support: BULK, INT ISO
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20200331081005.32752-4-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
And delete cdsn3_hw_role_state_machine declare which doesn't
be needed.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20200331081005.32752-3-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In short, we have three kinds of role switches:
- Based on SoC: ID and VBUS
- Based on external connnctor, eg, Type-C or GPIO Connector
- Based on user choices through sysfs
Since HW handling and usb-role-switch handling are at
different places, we do not need role_override any more,
and this flag could not judge external connector case well.
With role_override deleted, We use cdns3_hw_role_switch for
the 1st use case, and usb-role-switch for the 2nd and 3rd cases.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20200331081005.32752-2-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After that, the role switch device (eg, Type-C device) could call
cdns3_role_set to finish the role switch.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20200331081005.32752-1-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Corsair K70 RGB RAPIDFIRE needs the USB_QUIRK_DELAY_INIT and
USB_QUIRK_DELAY_CTRL_MSG to function or it will randomly not
respond on boot, just like other Corsair keyboards
Signed-off-by: Jonathan Cox <jonathan@jdcox.net>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200410212427.2886-1-jonathan@jdcox.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For userspace functions using OS Descriptors, if a function also supplies
Extended Property descriptors currently the counts and lengths stored in
the ms_os_descs_ext_prop_{count,name_len,data_len} variables are not
getting reset to 0 during an unbind or when the epfiles are closed. If
the same function is re-bound and the descriptors are re-written, this
results in those count/length variables to monotonically increase
causing the VLA allocation in _ffs_func_bind() to grow larger and larger
at each bind/unbind cycle and eventually fail to allocate.
Fix this by clearing the ms_os_descs_ext_prop count & lengths to 0 in
ffs_data_reset().
Fixes: f0175ab519 ("usb: gadget: f_fs: OS descriptors support")
Cc: stable@vger.kernel.org
Signed-off-by: Udipto Goswami <ugoswami@codeaurora.org>
Signed-off-by: Sriharsha Allenki <sallenki@codeaurora.org>
Reviewed-by: Manu Gautam <mgautam@codeaurora.org>
Link: https://lore.kernel.org/r/20200402044521.9312-1-sallenki@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Immediate submission in case of a babbling device can lead
to a busy loop. Introducing a delayed work.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Tested-by: Jonas Karlsson <jonas.karlsson@actia.se>
Link: https://lore.kernel.org/r/20200415151358.32664-2-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend increments a counter, then kills the URBs,
then kills the scheduled work. The scheduled work, however,
may reschedule the URBs. Fix this by having the work
check the counter.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Tested-by: Jonas Karlsson <jonas.karlsson@actia.se>
Link: https://lore.kernel.org/r/20200415151358.32664-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A SCSI error handler and block runtime PM must not allocate
memory with GFP_KERNEL. Furthermore they must not wait for
tasks allocating memory with GFP_KERNEL.
That means that they cannot share a workqueue with arbitrary tasks.
Fix this for UAS using a private workqueue.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: f9dc024a2d ("uas: pre_reset and suspend: Fix a few races")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200415141750.811-2-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Once a device is gone, the internal state does not matter anymore.
There is no need to spam the logs.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Fixes: 326349f824 ("uas: add dead request list")
Link: https://lore.kernel.org/r/20200415141750.811-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If queue->size check in raw_event_queue_fetch() fails (which normally
shouldn't happen, that check is a fail-safe), the function returns
without reenabling interrupts. This patch fixes that issue, along with
propagating the cause of failure to the function caller.
Fixes: f2c2e71764 ("usb: gadget: add raw-gadget interface")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Link: https://lore.kernel.org/r/9f7ce7a1472cfb9447f6c5a494186fa1f2670f6f.1586270396.git.andreyknvl@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The copy_to/from_user() functions return the number of bytes remaining
but we want to return negative error codes. I changed a couple checks
in raw_ioctl_ep_read() and raw_ioctl_ep0_read() to show that we still
we returning zero on error.
Fixes: f2c2e71764 ("usb: gadget: add raw-gadget interface")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Link: https://lore.kernel.org/r/20200406145119.GG68494@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit ef441dd6af ("usb: typec: mux: Allow the muxes to be named")
the typec_switch_desc and typec_mux_desc structs contain a name field.
The pi3usb30532 driver allocates these structs on the stack and so far did
not explicitly zero the mem used for the structs. This causes the new name
fields to point to a random memory address, which in my test case happens
to be a valid address leading to "interesting" mux / switch names:
[root@localhost ~]# ls -l /sys/class/typec_mux/
total 0
lrwxrwxrwx. 1 root root 0 Apr 14 12:55 ''$'\r''-switch' -> ...
lrwxrwxrwx. 1 root root 0 Apr 14 12:55 ''$'\320\302\006''2'$'...
Explicitly initialize the structs to zero when declaring them on the stack
so that any unused fields get set to 0, fixing this.
Fixes: ef441dd6af ("usb: typec: mux: Allow the muxes to be named")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200414133313.131802-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a bug that causes the USB3 early console to freeze after
printing a single line on AMD machines because it can't parse the
Transfer TRB properly.
The spec at
https://www.intel.com/content/dam/www/public/us/en/documents/technical-specifications/extensible-host-controler-interface-usb-xhci.pdf
says in section "4.5.1 Device Context Index" that the Context Index,
also known as Endpoint ID according to
section "1.6 Terms and Abbreviations", is normally computed as
`DCI = (Endpoint Number * 2) + Direction`, which matches the current
definitions of XDBC_EPID_OUT and XDBC_EPID_IN.
However, the numbering in a Debug Capability Context data structure is
supposed to be different:
Section "7.6.3.2 Endpoint Contexts and Transfer Rings" explains that a
Debug Capability Context data structure has the endpoints mapped to indices
0 and 1.
Change XDBC_EPID_OUT/XDBC_EPID_IN to the spec-compliant values, add
XDBC_EPID_OUT_INTEL/XDBC_EPID_IN_INTEL with Intel's incorrect values, and
let xdbc_handle_tx_event() handle both.
I have verified that with this patch applied, the USB3 early console works
on both an Intel and an AMD machine.
Fixes: aeb9dd1de9 ("usb/early: Add driver for xhci debug capability")
Cc: stable@vger.kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Link: https://lore.kernel.org/r/20200401074619.8024-1-jannh@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
FuzzUSB (a variant of syzkaller) found a free-while-still-in-use bug
in the USB scatter-gather library:
BUG: KASAN: use-after-free in atomic_read
include/asm-generic/atomic-instrumented.h:26 [inline]
BUG: KASAN: use-after-free in usb_hcd_unlink_urb+0x5f/0x170
drivers/usb/core/hcd.c:1607
Read of size 4 at addr ffff888065379610 by task kworker/u4:1/27
CPU: 1 PID: 27 Comm: kworker/u4:1 Not tainted 5.5.11 #2
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
1.10.2-1ubuntu1 04/01/2014
Workqueue: scsi_tmf_2 scmd_eh_abort_handler
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xce/0x128 lib/dump_stack.c:118
print_address_description.constprop.4+0x21/0x3c0 mm/kasan/report.c:374
__kasan_report+0x153/0x1cb mm/kasan/report.c:506
kasan_report+0x12/0x20 mm/kasan/common.c:639
check_memory_region_inline mm/kasan/generic.c:185 [inline]
check_memory_region+0x152/0x1b0 mm/kasan/generic.c:192
__kasan_check_read+0x11/0x20 mm/kasan/common.c:95
atomic_read include/asm-generic/atomic-instrumented.h:26 [inline]
usb_hcd_unlink_urb+0x5f/0x170 drivers/usb/core/hcd.c:1607
usb_unlink_urb+0x72/0xb0 drivers/usb/core/urb.c:657
usb_sg_cancel+0x14e/0x290 drivers/usb/core/message.c:602
usb_stor_stop_transport+0x5e/0xa0 drivers/usb/storage/transport.c:937
This bug occurs when cancellation of the S-G transfer races with
transfer completion. When that happens, usb_sg_cancel() may continue
to access the transfer's URBs after usb_sg_wait() has freed them.
The bug is caused by the fact that usb_sg_cancel() does not take any
sort of reference to the transfer, and so there is nothing to prevent
the URBs from being deallocated while the routine is trying to use
them. The fix is to take such a reference by incrementing the
transfer's io->count field while the cancellation is in progres and
decrementing it afterward. The transfer's URBs are not deallocated
until io->complete is triggered, which happens when io->count reaches
zero.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Kyungtae Kim <kt0755@gmail.com>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2003281615140.14837-100000@netrider.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Message logged by 'dev_xxx()' or 'pr_xxx()' should end with a '\n'.
Fixes: 541368b46b ("usb: phy: Add driver for the Ingenic JZ4770 USB transceiver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20200411063811.6767-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the SPDX License Identifier style in
header files related to DesignWare USB2 DRD Core Support.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Link: https://lore.kernel.org/r/20200328094828.GA5016@nishad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the SPDX License Identifier style in
header files related to MediaTek USB3 Dual Role controller.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20200404103728.GA6011@nishad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the SPDX License Identifier style in
header files related to USB Dual Role (OTG-ready) Controller Drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Link: https://lore.kernel.org/r/20200404104952.GA6575@nishad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the SPDX License Identifier style in
header files related to USB Miscellaneous drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Link: https://lore.kernel.org/r/20200404094638.GA5319@nishad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the SPDX License Identifier style in
header files related to ISP1760 USB host controller.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Link: https://lore.kernel.org/r/20200404093803.GA4983@nishad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the SPDX License Identifier style in
header files related to USB host controller drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Link: https://lore.kernel.org/r/20200404092135.GA4522@nishad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following cppcheck warnings:
drivers/usb/gadget/legacy/inode.c:1364:8: style: Redundant initialization for 'value'. The initialized value is overwritten$
value = -EOPNOTSUPP;
^
drivers/usb/gadget/legacy/inode.c:1331:15: note: value is initialized
int value = -EOPNOTSUPP;
^
drivers/usb/gadget/legacy/inode.c:1364:8: note: value is overwritten
value = -EOPNOTSUPP;
^
drivers/usb/gadget/legacy/inode.c:1817:8: style: Redundant initialization for 'value'. The initialized value is overwritten$
value = -EINVAL;
^
drivers/usb/gadget/legacy/inode.c:1787:18: note: value is initialized
ssize_t value = len, length = len;
^
drivers/usb/gadget/legacy/inode.c:1817:8: note: value is overwritten
value = -EINVAL;
^
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200403131652.8183-1-masahiroy@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
u132_static_list is a global list protected by u132_module_lock.
It is read in the u132_hcd_exit() function without holding the lock
thus may lead to data race.
However, it turns out that this list isn't used for anything useful
and thus it is okay to get rid of it.
Thus, remove the u132_static_list from u132-hcd module.
Also remove struct list_head u132_list from struct u132.
Found by Linux Driver Verification project (linuxtesting.org).
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com>
Link: https://lore.kernel.org/r/20200404174102.19862-1-madhuparnabhowmik10@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the SPDX License Identifier style in
header file related to early USB devices.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Link: https://lore.kernel.org/r/20200328104426.GA6401@nishad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the SPDX License Identifier style in
header files related to USB Core.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Link: https://lore.kernel.org/r/20200328091844.GA3648@nishad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The controller always supports link recovery for device in SS and SSP.
Remove the speed limit check. Also, when the device is in RESUME or
RESET state, it means the controller received the resume/reset request.
The driver must send the link recovery to acknowledge the request. They
are valid states for the driver to send link recovery.
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Fixes: ee5cd41c91 ("usb: dwc3: Update speed checks for SuperSpeedPlus")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Currently the calculation of max packet size limit for IN endpoints is
too restrictive. This prevents a matching of a capable hardware endpoint
during configuration. Below is the minimum recommended HW configuration
to support a particular endpoint setup from the databook:
For OUT endpoints, the databook recommended the minimum RxFIFO size to
be at least 3x MaxPacketSize + 3x setup packets size (8 bytes each) +
clock crossing margin (16 bytes).
For IN endpoints, the databook recommended the minimum TxFIFO size to be
at least 3x MaxPacketSize for endpoints that support burst. If the
endpoint doesn't support burst or when the device is operating in USB
2.0 mode, a minimum TxFIFO size of 2x MaxPacketSize is recommended.
Base on these recommendations, we can calculate the MaxPacketSize limit
of each endpoint. This patch revises the IN endpoint MaxPacketSize limit
and also sets the MaxPacketSize limit for OUT endpoints.
Reference: Databook 3.30a section 3.2.2 and 3.2.3
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Change the macro name DWC3_GTXFIFOSIZ_TXFDEF to DWC3_GTXFIFOSIZ_TXFDEP
to match with the register name GTXFIFOSIZ.TXFDEP.
Fixes: 457e84b662 ("usb: dwc3: gadget: dynamically re-size TxFifos")
Fixes: 0cab8d26d6 ("usb: dwc3: Update DWC_usb31 GTXFIFOSIZ reg fields")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
When building with Clang + -Wtautological-pointer-compare:
drivers/usb/gadget/udc/bdc/bdc_ep.c:543:28: warning: comparison of
address of 'req->queue' equal to a null pointer is always false
[-Wtautological-pointer-compare]
if (req == NULL || &req->queue == NULL || &req->usb_req == NULL)
~~~~~^~~~~ ~~~~
drivers/usb/gadget/udc/bdc/bdc_ep.c:543:51: warning: comparison of
address of 'req->usb_req' equal to a null pointer is always false
[-Wtautological-pointer-compare]
if (req == NULL || &req->queue == NULL || &req->usb_req == NULL)
~~~~~^~~~~~~ ~~~~
2 warnings generated.
As it notes, these statements will always evaluate to false so remove
them.
Fixes: efed421a94 ("usb: gadget: Add UDC driver for Broadcom USB3.0 device controller IP BDC")
Link: https://github.com/ClangBuiltLinux/linux/issues/749
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Allow to cut down on driver size for embedded config.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
ZEVIO glue code is is identical to generic binding now, but doesn't
enable runtime PM. Let's squash the driver and get runtime PM for free.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Allow clock to be missing from DT (assume it's enabled then).
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
pdata is copied anyway to allow setting device name.
Make the source const.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
update changing all our txt files to rst ones. Excluding that, we
have the usual driver updates (qla2xxx, ufs, lpfc, zfcp, ibmvfc,
pm80xx, aacraid), a treewide update for scnprintf and some other minor
updates. The major core update is Hannes moving functions out of the
aacraid driver and into the core.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXoYKiyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishSasAP4iGwSB
Y8tFaZgWadu76+wj5MdqTBoXdhnIuFF0rZG3pQEAiIKdsfQlbSFdm75+gUtx5hG/
GOilX/pJczTRJDCGNis=
=g7Sk
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This series has a huge amount of churn because it pulls in Mauro's doc
update changing all our txt files to rst ones.
Excluding that, we have the usual driver updates (qla2xxx, ufs, lpfc,
zfcp, ibmvfc, pm80xx, aacraid), a treewide update for scnprintf and
some other minor updates.
The major core change is Hannes moving functions out of the aacraid
driver and into the core"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (223 commits)
scsi: aic7xxx: aic97xx: Remove FreeBSD-specific code
scsi: ufs: Do not rely on prefetched data
scsi: dc395x: remove dc395x_bios_param
scsi: libiscsi: Fix error count for active session
scsi: hpsa: correct race condition in offload enabled
scsi: message: fusion: Replace zero-length array with flexible-array member
scsi: qedi: Add PCI shutdown handler support
scsi: qedi: Add MFW error recovery process
scsi: ufs: Enable block layer runtime PM for well-known logical units
scsi: ufs-qcom: Override devfreq parameters
scsi: ufshcd: Let vendor override devfreq parameters
scsi: ufshcd: Update the set frequency to devfreq
scsi: ufs: Resume ufs host before accessing ufs device
scsi: ufs-mediatek: customize the delay for enabling host
scsi: ufs: make HCE polling more compact to improve initialization latency
scsi: ufs: allow custom delay prior to host enabling
scsi: ufs-mediatek: use common delay function
scsi: ufs: introduce common and flexible delay function
scsi: ufs: use an enum for host capabilities
scsi: ufs: fix uninitialized tx_lanes in ufshcd_disable_tx_lcc()
...
Pull locking updates from Ingo Molnar:
"The main changes in this cycle were:
- Continued user-access cleanups in the futex code.
- percpu-rwsem rewrite that uses its own waitqueue and atomic_t
instead of an embedded rwsem. This addresses a couple of
weaknesses, but the primary motivation was complications on the -rt
kernel.
- Introduce raw lock nesting detection on lockdep
(CONFIG_PROVE_RAW_LOCK_NESTING=y), document the raw_lock vs. normal
lock differences. This too originates from -rt.
- Reuse lockdep zapped chain_hlocks entries, to conserve RAM
footprint on distro-ish kernels running into the "BUG:
MAX_LOCKDEP_CHAIN_HLOCKS too low!" depletion of the lockdep
chain-entries pool.
- Misc cleanups, smaller fixes and enhancements - see the changelog
for details"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (55 commits)
fs/buffer: Make BH_Uptodate_Lock bit_spin_lock a regular spinlock_t
thermal/x86_pkg_temp: Make pkg_temp_lock a raw_spinlock_t
Documentation/locking/locktypes: Minor copy editor fixes
Documentation/locking/locktypes: Further clarifications and wordsmithing
m68knommu: Remove mm.h include from uaccess_no.h
x86: get rid of user_atomic_cmpxchg_inatomic()
generic arch_futex_atomic_op_inuser() doesn't need access_ok()
x86: don't reload after cmpxchg in unsafe_atomic_op2() loop
x86: convert arch_futex_atomic_op_inuser() to user_access_begin/user_access_end()
objtool: whitelist __sanitizer_cov_trace_switch()
[parisc, s390, sparc64] no need for access_ok() in futex handling
sh: no need of access_ok() in arch_futex_atomic_op_inuser()
futex: arch_futex_atomic_op_inuser() calling conventions change
completion: Use lockdep_assert_RT_in_threaded_ctx() in complete_all()
lockdep: Add posixtimer context tracing bits
lockdep: Annotate irq_work
lockdep: Add hrtimer context tracing bits
lockdep: Introduce wait-type checks
completion: Use simple wait queues
sched/swait: Prepare usage in completions
...
- Clean up and rework the PM QoS API to simplify the code and
reduce the size of it (Rafael Wysocki).
- Fix a suspend-to-idle wakeup regression on Dell XPS13 9370
and similar platforms where the USB plug/unplug events are
handled by the EC (Rafael Wysocki).
- CLean up the intel_idle and PSCI cpuidle drivers (Rafael Wysocki,
Ulf Hansson).
- Extend the haltpoll cpuidle driver so that it can be forced to
run on some systems where it refused to load (Maciej Szmigiero).
- Convert several cpufreq documents to the .rst format and move the
legacy driver documentation into one common file (Mauro Carvalho
Chehab, Rafael Wysocki).
- Update several cpufreq drivers:
* Extend and fix the imx-cpufreq-dt driver (Anson Huang).
* Improve the -EPROBE_DEFER handling and fix unwanted CPU
overclocking on i.MX6ULL in imx6q-cpufreq (Anson Huang,
Christoph Niedermaier).
* Add support for Krait based SoCs to the qcom driver (Ansuel
Smith).
* Add support for OPP_PLUS to ti-cpufreq (Lokesh Vutla).
* Add platform specific intermediate callbacks support to
cpufreq-dt and update the imx6q driver (Peng Fan).
* Simplify and consolidate some pieces of the intel_pstate driver
and update its documentation (Rafael Wysocki, Alex Hung).
- Fix several devfreq issues:
* Remove unneeded extern keyword from a devfreq header file
and use the DEVFREQ_GOV_UPDATE_INTERNAL event name instead of
DEVFREQ_GOV_INTERNAL (Chanwoo Choi).
* Fix the handling of dev_pm_qos_remove_request() result (Leonard
Crestez).
* Use constant name for userspace governor (Pierre Kuo).
* Get rid of doc warnings and fix a typo (Christophe JAILLET).
- Use built-in RCU list checking in some places in the PM core to
avoid false-positive RCU usage warnings (Madhuparna Bhowmik).
- Add explicit READ_ONCE()/WRITE_ONCE() annotations to low-level
PM QoS routines (Qian Cai).
- Fix removal of wakeup sources to avoid NULL pointer dereferences
in a corner case (Neeraj Upadhyay).
- Clean up the handling of hibernate compat ioctls and fix the
related documentation (Eric Biggers).
- Update the idle_inject power capping driver to use variable-length
arrays instead of zero-length arrays (Gustavo Silva).
- Fix list format in a PM QoS document (Randy Dunlap).
- Make the cpufreq stats module use scnprintf() to avoid potential
buffer overflows (Takashi Iwai).
- Add pm_runtime_get_if_active() to PM-runtime API (Sakari Ailus).
- Allow no domain-idle-states DT property in generic PM domains (Ulf
Hansson).
- Fix a broken y-axis scale in the intel_pstate_tracer utility (Doug
Smythies).
-----BEGIN PGP SIGNATURE-----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=cBQd
-----END PGP SIGNATURE-----
Merge tag 'pm-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These clean up and rework the PM QoS API, address a suspend-to-idle
wakeup regression on some ACPI-based platforms, clean up and extend a
few cpuidle drivers, update multiple cpufreq drivers and cpufreq
documentation, and fix a number of issues in devfreq and several other
things all over.
Specifics:
- Clean up and rework the PM QoS API to simplify the code and reduce
the size of it (Rafael Wysocki).
- Fix a suspend-to-idle wakeup regression on Dell XPS13 9370 and
similar platforms where the USB plug/unplug events are handled by
the EC (Rafael Wysocki).
- CLean up the intel_idle and PSCI cpuidle drivers (Rafael Wysocki,
Ulf Hansson).
- Extend the haltpoll cpuidle driver so that it can be forced to run
on some systems where it refused to load (Maciej Szmigiero).
- Convert several cpufreq documents to the .rst format and move the
legacy driver documentation into one common file (Mauro Carvalho
Chehab, Rafael Wysocki).
- Update several cpufreq drivers:
* Extend and fix the imx-cpufreq-dt driver (Anson Huang).
* Improve the -EPROBE_DEFER handling and fix unwanted CPU
overclocking on i.MX6ULL in imx6q-cpufreq (Anson Huang,
Christoph Niedermaier).
* Add support for Krait based SoCs to the qcom driver (Ansuel
Smith).
* Add support for OPP_PLUS to ti-cpufreq (Lokesh Vutla).
* Add platform specific intermediate callbacks support to
cpufreq-dt and update the imx6q driver (Peng Fan).
* Simplify and consolidate some pieces of the intel_pstate
driver and update its documentation (Rafael Wysocki, Alex
Hung).
- Fix several devfreq issues:
* Remove unneeded extern keyword from a devfreq header file and
use the DEVFREQ_GOV_UPDATE_INTERNAL event name instead of
DEVFREQ_GOV_INTERNAL (Chanwoo Choi).
* Fix the handling of dev_pm_qos_remove_request() result
(Leonard Crestez).
* Use constant name for userspace governor (Pierre Kuo).
* Get rid of doc warnings and fix a typo (Christophe JAILLET).
- Use built-in RCU list checking in some places in the PM core to
avoid false-positive RCU usage warnings (Madhuparna Bhowmik).
- Add explicit READ_ONCE()/WRITE_ONCE() annotations to low-level PM
QoS routines (Qian Cai).
- Fix removal of wakeup sources to avoid NULL pointer dereferences in
a corner case (Neeraj Upadhyay).
- Clean up the handling of hibernate compat ioctls and fix the
related documentation (Eric Biggers).
- Update the idle_inject power capping driver to use variable-length
arrays instead of zero-length arrays (Gustavo Silva).
- Fix list format in a PM QoS document (Randy Dunlap).
- Make the cpufreq stats module use scnprintf() to avoid potential
buffer overflows (Takashi Iwai).
- Add pm_runtime_get_if_active() to PM-runtime API (Sakari Ailus).
- Allow no domain-idle-states DT property in generic PM domains (Ulf
Hansson).
- Fix a broken y-axis scale in the intel_pstate_tracer utility (Doug
Smythies)"
* tag 'pm-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (78 commits)
cpufreq: intel_pstate: Simplify intel_pstate_cpu_init()
tools/power/x86/intel_pstate_tracer: fix a broken y-axis scale
ACPI: PM: s2idle: Refine active GPEs check
ACPICA: Allow acpi_any_gpe_status_set() to skip one GPE
PM: sleep: wakeup: Skip wakeup_source_sysfs_remove() if device is not there
PM / devfreq: Get rid of some doc warnings
PM / devfreq: Fix handling dev_pm_qos_remove_request result
PM / devfreq: Fix a typo in a comment
PM / devfreq: Change to DEVFREQ_GOV_UPDATE_INTERVAL event name
PM / devfreq: Remove unneeded extern keyword
PM / devfreq: Use constant name of userspace governor
ACPI: PM: s2idle: Fix comment in acpi_s2idle_prepare_late()
cpufreq: qcom: Add support for krait based socs
cpufreq: imx6q-cpufreq: Improve the logic of -EPROBE_DEFER handling
cpufreq: Use scnprintf() for avoiding potential buffer overflow
cpuidle: psci: Split psci_dt_cpu_init_idle()
PM / Domains: Allow no domain-idle-states DT property in genpd when parsing
PM / hibernate: Remove unnecessary compat ioctl overrides
PM: hibernate: fix docs for ioctls that return loff_t via pointer
Documentation: intel_pstate: update links for references
...
Here are the big set of USB and PHY driver patches for 5.7-rc1.
Nothing huge here, some new PHY drivers, loads of USB gadget fixes and
updates, xhci updates, usb-serial driver updates and new device ids, and
other minor things. Full details in the shortlog.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXoHL9w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymz6wCcDwDTZouXj+0B37q+kwlCQQPyLukAn2CxKfrM
d+wScRHWoZutA8IdzqaU
=5+jn
-----END PGP SIGNATURE-----
Merge tag 'usb-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / PHY updates from Greg KH:
"Here are the big set of USB and PHY driver patches for 5.7-rc1.
Nothing huge here, some new PHY drivers, loads of USB gadget fixes and
updates, xhci updates, usb-serial driver updates and new device ids,
and other minor things. Full details in the shortlog.
All have been in linux-next for a while with no reported issues"
* tag 'usb-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (239 commits)
USB: cdc-acm: restore capability check order
usb: cdns3: make signed 1 bit bitfields unsigned
usb: gadget: fsl: remove unused variable 'driver_desc'
usb: gadget: f_fs: Fix use after free issue as part of queue failure
usb: typec: Correct the documentation for typec_cable_put()
USB: serial: io_edgeport: fix slab-out-of-bounds read in edge_interrupt_callback
USB: serial: option: add Wistron Neweb D19Q1
USB: serial: option: add BroadMobi BM806U
USB: serial: option: add support for ASKEY WWHC050
usb: core: Add ACPI support for USB interface devices
driver core: platform: Reimplement devm_platform_ioremap_resource
usb: dwc2: convert to devm_platform_get_and_ioremap_resource
usb: host: hisilicon: convert to devm_platform_get_and_ioremap_resource
usb: host: xhci-plat: convert to devm_platform_get_and_ioremap_resource
drivers: provide devm_platform_get_and_ioremap_resource()
phy: qcom-qusb2: Add new overriding tuning parameters in QUSB2 V2 PHY
phy: qcom-qusb2: Add support for overriding tuning parameters in QUSB2 V2 PHY
dt-bindings: phy: qcom-qusb2: Add support for overriding Phy tuning parameters
phy: qcom-qusb2: Add generic QUSB2 V2 PHY support
dt-bindings: phy: qcom,qusb2: Add compatibles for QUSB2 V2 phy and SC7180
...
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE+QmuaPwR3wnBdVwACF8+vY7k4RUFAl6Bvm0ACgkQCF8+vY7k
4RViMQ//baNJyAA8/Hpxz1w5+nL5hsTOhf2PcPgnCLkRVQnIiKMZoq7AS5KWtbqu
im0SM6nWduGc2T/44Ew13YmBnuWMdXL9Gs8XtAkNakgSV1UM+A3pRuOWRYCyU3Ts
1QDsc3N7oY9cvyJGWOlqdcA4gp4AaKxjS6M6Z18wYBk/jYSCcj4ZVecT89DYeeM7
wFORkv/xSdgC3eoKWEwTyglzUmrXKrbfHdcNWrQBg+1SN3WrMYQWCL6nSYMqn0Vu
f9L5E6jUSx9s6+apxS0OUQmDj78RM1JCEY1P8lgc3tAtVJ+X3yZbxwtpcvujhFPv
c48NUQeyxAJc7evarvkd73Gwl4buujqHSgiRUovHwqUXHJuGZ3PBTryV9HzbmYYy
EeHS/23t09F3j9zYtuoDNFIED03Mi+TNeS04cq8OIfwNl7xpUSEV0S/wd11V2308
cfm6lsogGE9HRbaIxCHgx4AiGFVhbpK1OQt66iYze8r/wyxnN8MVOHGWw+eI4LRK
9gwh7Wx37k6uCrjfOnLSgx7kcJ+mxSZEYyHJZqqtPm9H1SC68GOxhL/S3Zu7arvK
eiwFfxJBiunCEfauOx28kaAdvBZVyEvYeDFYl/k+q4DCIGjvK0FXud6QRjNXv24S
qUXYZKPUALTFOpbkQ3IQiBOQNM4NhF15RzCqRUptVnlF05MSywg=
=Ve8R
-----END PGP SIGNATURE-----
Merge tag 'media/v5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- New sensor driver: imx219
- Support for some new pixelformats
- Support for Sun8i SoC
- Added more codecs to meson vdec driver
- Prepare for removing the legacy usbvision driver by moving it to
staging. This driver has issues and use legacy core APIs. If nobody
steps up to address those, it is time for its retirement.
- Several cleanups and improvements on drivers, with the addition of
new supported boards
* tag 'media/v5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (236 commits)
media: venus: firmware: Ignore secure call error on first resume
media: mtk-vpu: load vpu firmware from the new location
media: i2c: video-i2c: fix build errors due to 'imply hwmon'
media: MAINTAINERS: add myself to co-maintain Hantro G1/G2 for i.MX8MQ
media: hantro: add initial i.MX8MQ support
media: dt-bindings: Document i.MX8MQ VPU bindings
media: vivid: fix incorrect PA assignment to HDMI outputs
media: hantro: Add linux-rockchip mailing list to MAINTAINERS
media: cedrus: h264: Fix 4K decoding on H6
media: siano: Use scnprintf() for avoiding potential buffer overflow
media: rc: Use scnprintf() for avoiding potential buffer overflow
media: allegro: create new struct for channel parameters
media: allegro: move mail definitions to separate file
media: allegro: pass buffers through firmware
media: allegro: verify source and destination buffer in VCU response
media: allegro: handle dependency of bitrate and bitrate_peak
media: allegro: read bitrate mode directly from control
media: allegro: make QP configurable
media: allegro: make frame rate configurable
media: allegro: skip filler data if possible
...
The pointer value is "ptrval" like below at current code:
ci_hdrc ci_hdrc.0: ChipIdea HDRC found, revision: 25, lpm: 0;
cap: (ptrval) op: (ptrval)
According to Documentation/core-api/printk-formats.rst, we change
it from %p to %px for real value.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
commit b401f8c4f4 ("USB: cdc-acm: fix rounding error in TIOCSSERIAL")
introduced a regression by changing the order of capability and close
settings change checks. When running with CAP_SYS_ADMIN setting the
close settings to the values already set resulted in -EOPNOTSUPP.
Fix this by changing the check order back to how it was before.
Fixes: b401f8c4f4 ("USB: cdc-acm: fix rounding error in TIOCSSERIAL")
Cc: Anthony Mallet <anthony.mallet@laas.fr>
Cc: stable <stable@vger.kernel.org>
Cc: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Matthias Reichl <hias@horus.com>
Link: https://lore.kernel.org/r/20200327150350.3657-1-hias@horus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The signed 1 bit bitfields should be unsigned, so make them unsigned.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200325125041.94769-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/usb/gadget/udc/fsl_udc_core.c:56:19:
warning: 'driver_desc' defined but not used [-Wunused-const-variable=]
It is never used, so remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200326071419.19240-1-yuehaibing@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In AIO case, the request is freed up if ep_queue fails.
However, io_data->req still has the reference to this freed
request. In the case of this failure if there is aio_cancel
call on this io_data it will lead to an invalid dequeue
operation and a potential use after free issue.
Fix this by setting the io_data->req to NULL when the request
is freed as part of queue failure.
Fixes: 2e4c7553cd ("usb: gadget: f_fs: add aio support")
Signed-off-by: Sriharsha Allenki <sallenki@codeaurora.org>
CC: stable <stable@vger.kernel.org>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200326115620.12571-1-sallenki@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
typec_cable_put() function had typec_cable_get in it's documentation.
Change it to reflect the correct name.
Signed-off-by: Azhar Shaikh <azhar.shaikh@intel.com>
Link: https://lore.kernel.org/r/20200326134633.26780-1-azhar.shaikh@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the USB-serial updates for 5.7-rc1, including:
- support for a new family of Fintek devices
- fix for an io-edgeport slab-out-of-bounds access
- fixes for a couple of kernel-doc issues
Included are also various clean ups and some new modem device ids.
All but the io-edgeport fix have been in linux-next with no reported
issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXnx+TQAKCRALxc3C7H1l
CEGnAQCCITnwkGkLZe64yyEM9txUw5oXSRFvoURs7en/2+2YZQD/br8Ygn24NgFh
Qg0dZKSoh7FLGGlJm2Dnny31Edz7kAY=
=k8M6
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.7-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 5.7-rc1
Here are the USB-serial updates for 5.7-rc1, including:
- support for a new family of Fintek devices
- fix for an io-edgeport slab-out-of-bounds access
- fixes for a couple of kernel-doc issues
Included are also various clean ups and some new modem device ids.
All but the io-edgeport fix have been in linux-next with no reported
issues.
* tag 'usb-serial-5.7-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: io_edgeport: fix slab-out-of-bounds read in edge_interrupt_callback
USB: serial: option: add Wistron Neweb D19Q1
USB: serial: option: add BroadMobi BM806U
USB: serial: option: add support for ASKEY WWHC050
USB: serial: f81232: add control driver for F81534A
USB: serial: fix tty cleanup-op kernel-doc
USB: serial: clean up carrier-detect helper
USB: serial: f81232: set F81534A serial port with RS232 mode
USB: serial: f81232: add F81534A support
USB: serial: f81232: use devm_kzalloc for port data
USB: serial: f81232: add tx_empty function
USB: serial: f81232: extract LSR handler
USB: serial: digi_acceleport: remove redundant assignment to pointer priv
USB: serial: relax unthrottle memory barrier
Fix slab-out-of-bounds read in the interrupt-URB completion handler.
The boundary condition should be (length - 1) as we access
data[position + 1].
Reported-and-tested-by: syzbot+37ba33391ad5f3935bbd@syzkaller.appspotmail.com
Signed-off-by: Qiujun Huang <hqjagain@gmail.com>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Currently on ACPI-enabled systems the USB interface device has no link to
the actual firmware node and thus drivers may not parse additional information
given in the table. The new feature, proposed here, allows to pass properties
or other information to the drivers.
The ACPI companion of the device has to be set for USB interface devices
to achieve above. Use ACPI_COMPANION_SET macro to set this.
Note, OF already does link of_node and this is the same for ACPI case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/20200324100923.8332-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_platform_get_and_ioremap_resource() to simplify code, which
contains platform_get_resource() and devm_ioremap_resource(), it also
get the resource for use by the following code.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Link: https://lore.kernel.org/r/20200323160612.17277-5-zhengdejin5@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_platform_get_and_ioremap_resource() to simplify code, which
contains platform_get_resource() and devm_ioremap_resource(), it also
get the resource for use by the following code.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Link: https://lore.kernel.org/r/20200323160612.17277-4-zhengdejin5@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_platform_get_and_ioremap_resource() to simplify code, which
contains platform_get_resource() and devm_ioremap_resource(), it also
get the resource for use by the following code.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Link: https://lore.kernel.org/r/20200323160612.17277-3-zhengdejin5@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
completion uses a wait_queue_head_t to enqueue waiters.
wait_queue_head_t contains a spinlock_t to protect the list of waiters
which excludes it from being used in truly atomic context on a PREEMPT_RT
enabled kernel.
The spinlock in the wait queue head cannot be replaced by a raw_spinlock
because:
- wait queues can have custom wakeup callbacks, which acquire other
spinlock_t locks and have potentially long execution times
- wake_up() walks an unbounded number of list entries during the wake up
and may wake an unbounded number of waiters.
For simplicity and performance reasons complete() should be usable on
PREEMPT_RT enabled kernels.
completions do not use custom wakeup callbacks and are usually single
waiter, except for a few corner cases.
Replace the wait queue in the completion with a simple wait queue (swait),
which uses a raw_spinlock_t for protecting the waiter list and therefore is
safe to use inside truly atomic regions on PREEMPT_RT.
There is no semantical or functional change:
- completions use the exclusive wait mode which is what swait provides
- complete() wakes one exclusive waiter
- complete_all() wakes all waiters while holding the lock which protects
the wait queue against newly incoming waiters. The conversion to swait
preserves this behaviour.
complete_all() might cause unbound latencies with a large number of waiters
being woken at once, but most complete_all() usage sites are either in
testing or initialization code or have only a really small number of
concurrent waiters which for now does not cause a latency problem. Keep it
simple for now.
The fixup of the warning check in the USB gadget driver is just a straight
forward conversion of the lockless waiter check from one waitqueue type to
the other.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Davidlohr Bueso <dbueso@suse.de>
Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lkml.kernel.org/r/20200321113242.317954042@linutronix.de
ep_io() uses a completion on stack and open codes the waiting with:
wait_event_interruptible (done.wait, done.done);
and
wait_event (done.wait, done.done);
This waits in non-exclusive mode for complete(), but there is no reason to
do so because the completion can only be waited for by the task itself and
complete() wakes exactly one exlusive waiter.
Replace the open coded implementation with the corresponding
wait_for_completion*() functions.
No functional change.
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lkml.kernel.org/r/20200321113241.043380271@linutronix.de
These changes add USB OTG support for the XUSB host and XUSB device
controllers found on NVIDIA Tegra SoCs.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCAAxFiEEiOrDCAFJzPfAjcif3SOs138+s6EFAl5zgcgTHHRyZWRpbmdA
bnZpZGlhLmNvbQAKCRDdI6zXfz6zobyDD/45Ycsxyp3q9XSwimlDY+bxD5Y+Eo1y
vHD/vCNxm1bjlKhXiH5QML/AuJd21nzVa+tdbCI3qI/IzOxjdJEyIroh9HDdKFvB
1Ifl6BuxWjuLabFG/9+7PWzac3y85+2RFEn9154xDuVH+VGVZH8espFB93EAwgyM
SwrFicfK+H9stCl+cw6h1QZGluJbyK+j16Afed7LQLALPbJXjPqEPi3SBAyzzmQt
c04CTE3vjAB4lC24O4Cyosz1xpMQ2D7BQCZcvZt+a5EVJ78yqCVChdmg8WF4uVWm
6zhx7ibUrYANbIB6VjRlghPi5UKVobv0beR2zqfOmD5L2Oo4lyQjZslpCrDgD3l5
R2dEo0iRJ9z+WWGQ+eTvnkUa+tIZCNt4AYQYZw8Jbf+kFHtqsdbw5odMwOx+Vbf+
MWi0xa1mdC7/6+gXMGpdgpBxgd0G/ZyJqrUqI99R4f8FOHS4/cO02xe7aS29Wfv5
Om3TgkzS6V1H4zktUryRjaagGFDI/2/jg0Hl/PfQ7Q2yWGAZIMbnqOvbp6uLEcX1
kOx1Zeb3m6fH44N/soQbGRbEws7e9QwHpmscuQ/jq0/f/yF73i6BMOGjvEST21hm
Kx7fu/xDQnWrsfkUl8VNv+UA3prIIKKIBTio3wx0araV5C3CFLLompqRn6DLg1ZW
sjiUFiSYREwMGw==
=ORe3
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.7-usb-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into usb-next
Thierry writes:
usb: tegra: Changes for v5.7-rc1
These changes add USB OTG support for the XUSB host and XUSB device
controllers found on NVIDIA Tegra SoCs.
* tag 'tegra-for-5.7-usb-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
usb: gadget: tegra-xudc: Support multiple device modes
usb: gadget: tegra-xudc: Use phy_set_mode() to set/unset device mode
usb: gadget: tegra-xudc: Add usb-phy support
usb: gadget: tegra-xudc: Remove usb-role-switch support
usb: xhci-tegra: Add OTG support
phy: tegra: Select USB_PHY
phy: tegra: Don't use device-managed API to allocate ports
phy: tegra: Fix regulator leak
phy: tegra: Print -EPROBE_DEFER error message at debug level
phy: tegra: xusb: Don't warn on probe defer
phy: tegra: xusb: Add Tegra194 support
phy: tegra: xusb: Protect Tegra186 soc with config
phy: tegra: xusb: Add set_mode support for UTMI phy on Tegra186
phy: tegra: xusb: Add set_mode support for USB 2 phy on Tegra210
phy: tegra: xusb: Add support to get companion USB 3 port
phy: tegra: xusb: Add usb-phy support
phy: tegra: xusb: Add usb-role-switch support
This change supports limited multiple device modes by:
- At most 4 ports contains OTG/Device capability.
- One port run as device mode at a time.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When device mode is set/unset, VBUS override activity is done via
exported functions from padctl driver. Use phy_set_mode() instead.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
usb-phy is used to get notified on the USB role changes. Get usb-phy from
the UTMI PHY.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Padctl driver will act as a central driver to receive USB role changes via
usb-role-switch. This is updated to corresponding host, device drivers.
Hence remove usb-role-switch from XUDC driver.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
[treding@nvidia.com: rebase onto Greg's usb-next branch]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Get usb-phy's for availbale USB 2 phys. Register id notifiers for available
usb-phy's to receive role change notifications. Perform PP for the received
role change usb ports.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
[treding@nvidia.com: rebase onto Greg's usb-next branch]
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Fintek F81534A series contains 1 HUB, 1 GPIO device and n UARTs. The
UARTs are disabled by default and need to be enabled by the GPIO device
(2c42:16F8).
When F81534A plug to host, we can only see 1 HUB and 1 GPIO device and
we write 0x8fff to GPIO device register F81534A_CTRL_CMD_ENABLE_PORT
(116h) to enable all available serial ports.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
[johan: reword commit message and an error message slightly]
Signed-off-by: Johan Hovold <johan@kernel.org>
Here are a couple of new device ids for 5.6-rc.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXnHejAAKCRALxc3C7H1l
CAhmAQCbhFH890bBww476lWhYkBXlSCv3RmHcbZq9wqQ1F7AygD/VnWB14q0nDL/
bMw2mijztEsi8NEuVj/wh6p99I0+BAY=
=qeWa
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.6-rc7' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.6-rc7
Here are a couple of new device ids for 5.6-rc.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.6-rc7' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: pl2303: add device-id for HP LD381
USB: serial: option: add ME910G1 ECM composition 0x110b
By default, tty_port_init() initializes those parameters to a multiple
of HZ. For instance in line 69 of tty_port.c:
port->close_delay = (50 * HZ) / 100;
https://github.com/torvalds/linux/blob/master/drivers/tty/tty_port.c#L69
With e.g. CONFIG_HZ = 250 (as this is the case for Ubuntu 18.04
linux-image-4.15.0-37-generic), the default setting for close_delay is
thus 125.
When ioctl(fd, TIOCGSERIAL, &s) is executed, the setting returned in
user space is '12' (125/10). When ioctl(fd, TIOCSSERIAL, &s) is then
executed with the same setting '12', the value is interpreted as '120'
which is different from the current setting and a EPERM error may be
raised by set_serial_info() if !CAP_SYS_ADMIN.
https://github.com/torvalds/linux/blob/master/drivers/usb/class/cdc-acm.c#L919
Fixes: ba2d8ce9db ("cdc-acm: implement TIOCSSERIAL to avoid blocking close(2)")
Signed-off-by: Anthony Mallet <anthony.mallet@laas.fr>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200312133101.7096-2-anthony.mallet@laas.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
close_delay and closing_wait are specified in hundredth of a second but stored
internally in jiffies. Use the jiffies_to_msecs() and msecs_to_jiffies()
functions to convert from each other.
Signed-off-by: Anthony Mallet <anthony.mallet@laas.fr>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200312133101.7096-1-anthony.mallet@laas.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have been receiving bug reports that ethernet connections over
RTL8153 based ethernet adapters stops working after a while with
errors like these showing up in dmesg when the ethernet stops working:
[12696.189484] r8152 6-1:1.0 enp10s0u1: Tx timeout
[12702.333456] r8152 6-1:1.0 enp10s0u1: Tx timeout
[12707.965422] r8152 6-1:1.0 enp10s0u1: Tx timeout
This has been reported on Dell WD15 docks, Belkin USB-C Express Dock 3.1
docks and with generic USB to ethernet dongles using the RTL8153
chipsets. Some users have tried adding usbcore.quirks=0bda:8153:k to
the kernel commandline and all users who have tried this report that
this fixes this.
Also note that we already have an existing NO_LPM quirk for the RTL8153
used in the Microsoft Surface Dock (where it uses a different usb-id).
This commit adds a NO_LPM quirk for the generic Realtek RTL8153
0bda:8153 usb-id, fixing the Tx timeout errors on these devices.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=198931
Cc: stable@vger.kernel.org
Cc: russianneuromancer@ya.ru
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200313120708.100339-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the SPDX License Identifier style in
header files related to Cypress C67X00 USB Controller.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Link: https://lore.kernel.org/r/20200315104022.GA3998@nishad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the SPDX License Identifier style in
header file related to USB DSL modem support drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Link: https://lore.kernel.org/r/20200315102844.GA3460@nishad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace "unsigned" to "u32" for checkpatch fix to tusb_writeb().
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200316211136.2274-9-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When handling a PIO bulk transfer with highmem buffer, a temporary
mapping is assigned to urb->transfer_buffer. After the transfer is
complete, an invalid address is left behind in this pointer. This is
not ordinarily a problem since nothing touches that buffer before the
urb is released. However, when usbmon is active, usbmon_urb_complete()
calls (indirectly) mon_bin_get_data() which does access the transfer
buffer if it is set. To prevent an invalid memory access here, reset
urb->transfer_buffer to NULL when finished (musb_host_rx()), or do not
set it at all (musb_host_tx()).
Fixes: 8e8a551654 ("usb: musb: host: Handle highmem in PIO mode")
Signed-off-by: Mans Rullgard <mans@mansr.com>
Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200316211136.2274-8-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for probing the jz4740-musb driver on the JZ4770 SoC.
The USB IP in the JZ4770 works the same Inventra IP as for the JZ4740,
but it features more endpoints, and officially supports OTG.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200316211136.2274-7-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The jz4740-musb driver is unconditionally probed from devicetree, so we
can add a hard dependency on devicetree. This makes the code a bit
cleaner, and is more future-proof as the platform data is now retrieved
using of_device_get_match_data().
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200316211136.2274-6-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Register a USB role switch, in order to get notified by the connector
driver when the USB role changes. The notification is then transmitted
to the PHY.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200316211136.2274-5-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for using the DMA channels built into the Inventra IP.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200316211136.2274-4-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable ret is being initialized with a value that is never read,
it is assigned a new value later on. The assignment is redundant
and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200316211136.2274-2-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Cover one cover case during suspend/resume
- Some SPDX License changes
The code changes are at my ci-for-usb-next many days,
no issue is reported.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEDaZUZmFxRG/wNThrSFkpgVDWcbsFAl5wwB8ACgkQSFkpgVDW
cbslugf+JWZDVDKqZlEmmY+mPCFSw2afWtrX1scbGOdsj2LcOIzzMn4H7+7W0DiY
TUelYThTHf6HlgfMPdsdpqZn9u5lK770Krw99/nDdux49CMdkoLhTH1gYoqhkw7P
6ORtA41cWcBzxQXk4qYIFuAVh4z7cT58PhUuqnrCnjJh6pThEiPTfhIr728nB3De
qaRGun0srWsN4WLmBGvhnY673nSbPLBP9Om5wfV2v33yR+vTeza8mgvzI0w2R1w6
TUa3TfbS3+d7NC0GbEhUG16ZEcc3geohMwiLu1/8iYF0CBV4U5tPKNNbieIIVzCo
YgT9Nn5/bPWrk33cMoQ6NSCkTPtkfA==
=QcDe
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
- Improve the runtime pm
- Cover one cover case during suspend/resume
- Some SPDX License changes
The code changes are at my ci-for-usb-next many days,
no issue is reported.
* tag 'usb-ci-v5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
USB: chipidea: Use the correct style for SPDX License Identifier
usb: chipidea: otg: handling vbus disconnect event occurred during system suspend
usb: chipidea: udc: using structure ci_hdrc device for runtime PM
Move the get_unaligned_be24(), get_unaligned_le24() and
put_unaligned_le24() definitions from various drivers into
include/linux/unaligned/generic.h. Add a put_unaligned_be24()
implementation.
Link: https://lore.kernel.org/r/20200313203102.16613-4-bvanassche@acm.org
Cc: Keith Busch <kbusch@kernel.org>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Jens Axboe <axboe@fb.com>
Cc: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> # For drivers/usb
Reviewed-by: Felipe Balbi <balbi@kernel.org> # For drivers/usb/gadget
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
drivers/usb/gadget/legacy/Kconfig creates a 'choice' inside another
'choice'.
The outer choice: line 17 "USB Gadget precomposed configurations"
The inner choice: line 484 "EHCI Debug Device mode"
I wondered why the whole legacy gadget drivers reside in such a big
choice block.
This dates back to 2003, "[PATCH] USB: fix for multiple definition of
`usb_gadget_get_string'". [1]
At that time, the global function, usb_gadget_get_string(), was linked
into multiple drivers. That was why only one driver was able to become
built-in at the same time.
Later, commit a84d9e5361 ("usb: gadget: start with libcomposite")
moved usb_gadget_get_string() to a separate module, libcomposite.ko
instead of including usbstring.c from multiple modules.
More and more refactoring was done, and after commit 1bcce93947
("usb: gadget: multi: convert to new interface of f_mass_storage"),
you can link multiple gadget drivers into vmlinux without causing
multiple definition error.
This is the only user of the nested choice structure ever. Removing
this mess will make some Kconfig cleanups possible.
[1]: https://git.kernel.org/pub/scm/linux/kernel/git/history/history.git/commit/?id=fee4cf49a81381e072c063571d1aadbb29207408
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/20200315154948.26569-1-masahiroy@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After merging the usb-gadget tree, today's linux-next build (arm
multi_v7_defconfig) failed like this:
drivers/usb/dwc3/drd.c: In function 'dwc3_setup_role_switch':
drivers/usb/dwc3/drd.c:551:23: error: assignment to 'usb_role_switch_set_t' {aka 'int (*)(struct usb_role_switch *, enum usb_role)'} from incompatible pointer type 'int (*)(struct device *, enum usb_role)' [-Werror=incompatible-pointer-types]
551 | dwc3_role_switch.set = dwc3_usb_role_switch_set;
| ^
drivers/usb/dwc3/drd.c:552:23: error: assignment to 'usb_role_switch_get_t' {aka 'enum usb_role (*)(struct usb_role_switch *)'} from incompatible pointer type 'enum usb_role (*)(struct device *)' [-Werror=incompatible-pointer-types]
552 | dwc3_role_switch.get = dwc3_usb_role_switch_get;
| ^
Caused by commit
8a0a137997 ("usb: dwc3: Registering a role switch in the DRD code.")
interacting with commit
bce3052f0c ("usb: roles: Provide the switch drivers handle to the switch in the API")
from the usb tree.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20200316143752.473f1073@canb.auug.org.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lots of changes on dwc3 this time, most of them from Thinh fixing a
bunch of really old mishaps on the driver.
DWC2 got support for STM32MP15 and a couple RockChip SoCs while DWC3
learned about Amlogic A1 family.
Apart from these, we have a few spelling fixes and other minor
non-critical fixes all over the place.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
-----BEGIN PGP SIGNATURE-----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=L9gx
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: changes for v5.7 merge window
Lots of changes on dwc3 this time, most of them from Thinh fixing a
bunch of really old mishaps on the driver.
DWC2 got support for STM32MP15 and a couple RockChip SoCs while DWC3
learned about Amlogic A1 family.
Apart from these, we have a few spelling fixes and other minor
non-critical fixes all over the place.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
* tag 'usb-for-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (41 commits)
dt-bindings: usb: add documentation for aspeed usb-vhub
ARM: dts: aspeed-g4: add vhub port and endpoint properties
ARM: dts: aspeed-g5: add vhub port and endpoint properties
ARM: dts: aspeed-g6: add usb functions
usb: gadget: aspeed: add ast2600 vhub support
usb: gadget: aspeed: read vhub properties from device tree
usb: gadget: aspeed: support per-vhub usb descriptors
usb: gadget: f_phonet: Replace zero-length array with flexible-array member
usb: gadget: composite: Inform controller driver of self-powered
usb: gadget: amd5536udc: fix spelling mistake "reserverd" -> "reserved"
udc: s3c-hsudc: Silence warning about supplies during deferred probe
usb: dwc2: Silence warning about supplies during deferred probe
dt-bindings: usb: dwc2: add compatible property for rk3368 usb
dt-bindings: usb: dwc2: add compatible property for rk3328 usb
usb: gadget: add raw-gadget interface
usb: dwc2: Implement set_selfpowered()
usb: dwc3: qcom: Replace <linux/clk-provider.h> by <linux/of_clk.h>
usb: dwc3: core: don't do suspend for device mode if already suspended
usb: dwc3: Rework resets initialization to be more flexible
usb: dwc3: Rework clock initialization to be more flexible
...
During system suspend, the role switch may occur, eg, from gadget->host.
In this case, the vbus disconnect event is lost, we add this handling
in role switch routine in this commit.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
At current code, it doesn't maintain ci->gadget.dev's runtime PM
status well, eg, during the PM operation, the PM counter for
ci->gadget.dev doesn't be changed accordingly.
In this commit, we use ci_hdrc device instead of ci->gadget.dev
for runtime PM APIs at udc driver, in the way, we handle runtime
PM APIs using unify device structure between core and udc driver.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Add AST2600 support in aspeed-vhub driver. There are 3 major differences
between AST2500 and AST2600 vhub:
- AST2600 supports 7 downstream ports while AST2500 supports 5.
- AST2600 supports 21 generic endpoints while AST2500 supports 15.
- EP0 data buffer's 8-byte DMA alignment restriction is removed from
AST2600.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The patch introduces 2 DT properties ("aspeed,vhub-downstream-ports" and
"aspeed,vhub-generic-endpoints") which replaces hardcoded port/endpoint
number. It is to make it more convenient to add support for newer vhub
revisions with different number of ports and endpoints.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch store vhub's standard usb descriptors in struct "ast_vhub" so
it's more convenient to customize descriptors and potentially support
multiple vhub instances in the future.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertenly introduced[3] to the codebase from now on.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Different configuration/condition may draw different power. Inform the
controller driver of the change so it can respond properly (e.g.
GET_STATUS request). This fixes an issue with setting MaxPower from
configfs. The composite driver doesn't check this value when setting
self-powered.
Cc: stable@vger.kernel.org
Fixes: 88af8bbe4e ("usb: gadget: the start of the configfs interface")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The variable is named reserved, the comment should say so.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Don't confuse user with meaningless warning about the failure in getting
supplies in case of deferred probe.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Don't confuse user with meaningless warning about the failure in getting
supplies in case of deferred probe.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
USB Raw Gadget is a kernel module that provides a userspace interface for
the USB Gadget subsystem. Essentially it allows to emulate USB devices
from userspace. Enabled with CONFIG_USB_RAW_GADGET. Raw Gadget is
currently a strictly debugging feature and shouldn't be used in
production.
Raw Gadget is similar to GadgetFS, but provides a more low-level and
direct access to the USB Gadget layer for the userspace. The key
differences are:
1. Every USB request is passed to the userspace to get a response, while
GadgetFS responds to some USB requests internally based on the provided
descriptors. However note, that the UDC driver might respond to some
requests on its own and never forward them to the Gadget layer.
2. GadgetFS performs some sanity checks on the provided USB descriptors,
while Raw Gadget allows you to provide arbitrary data as responses to
USB requests.
3. Raw Gadget provides a way to select a UDC device/driver to bind to,
while GadgetFS currently binds to the first available UDC.
4. Raw Gadget uses predictable endpoint names (handles) across different
UDCs (as long as UDCs have enough endpoints of each required transfer
type).
5. Raw Gadget has ioctl-based interface instead of a filesystem-based one.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
dwc2 always reports as self-powered in response to a device status
request. Implement the set_selfpowered() operations so that the gadget
can report as bus-powered when appropriate.
This is modelled on the dwc3 implementation.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The DWC3 USB driver is not a clock provider, and just needs to call
of_clk_get_parent_count().
Hence it can include <linux/of_clk.h> instead of <linux/clk-provider.h>.
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If dwc->dev in device mode already runtime suspended, don't do it again
for system suspend.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The dwc3 core binding specifies one reset.
However some variants of the hardware may have more. Previously
this was handled by using the dwc3-of-simple glue driver, but
that resulted in a proliferation of bindings for for every
variant, when the only difference was the clocks and resets
lists.
So this patch reworks the reading of the resets to fetch all the
resets specified in the dts together.
This patch was recommended by Rob Herring <robh@kernel.org>
as an alternative to creating multiple bindings for each variant
of hardware.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
CC: ShuFan Lee <shufan_lee@richtek.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Yu Chen <chenyu56@huawei.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Jun Li <lijun.kernel@gmail.com>
Cc: Valentin Schneider <valentin.schneider@arm.com>
Cc: Guillaume Gardet <Guillaume.Gardet@arm.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: linux-usb@vger.kernel.org
Cc: devicetree@vger.kernel.org
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The dwc3 core binding specifies three clocks:
ref, bus_early, and suspend
which are all controlled in the driver together.
However some variants of the hardware my not have all three
clks, or some may have more. Usually this was handled by using
the dwc3-of-simple glue driver, but that resulted in a
proliferation of bindings for for every variant, when the only
difference was the clocks and resets lists.
So this patch reworks the reading of the clks from the dts to
use devm_clk_bulk_get_all() will will fetch all the clocks
specified in the dts together.
This patch was recommended by Rob Herring <robh@kernel.org>
as an alternative to creating multiple bindings for each variant
of hardware.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
CC: ShuFan Lee <shufan_lee@richtek.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Yu Chen <chenyu56@huawei.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Jun Li <lijun.kernel@gmail.com>
Cc: Valentin Schneider <valentin.schneider@arm.com>
Cc: Guillaume Gardet <Guillaume.Gardet@arm.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: linux-usb@vger.kernel.org
Cc: devicetree@vger.kernel.org
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Support the new role-switch-default-mode binding for configuring
the default role the controller assumes as when the usb role is
USB_ROLE_NONE
This patch was split out from a larger patch originally by
Yu Chen <chenyu56@huawei.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
CC: ShuFan Lee <shufan_lee@richtek.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Yu Chen <chenyu56@huawei.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Jun Li <lijun.kernel@gmail.com>
Cc: Valentin Schneider <valentin.schneider@arm.com>
Cc: Guillaume Gardet <Guillaume.Gardet@arm.com>
Cc: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: linux-usb@vger.kernel.org
Cc: devicetree@vger.kernel.org
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The Type-C drivers use USB role switch API to inform the
system about the negotiated data role, so registering a role
switch in the DRD code in order to support platforms with
USB Type-C connectors.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
CC: ShuFan Lee <shufan_lee@richtek.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Yu Chen <chenyu56@huawei.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Jun Li <lijun.kernel@gmail.com>
Cc: Valentin Schneider <valentin.schneider@arm.com>
Cc: Guillaume Gardet <Guillaume.Gardet@arm.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: linux-usb@vger.kernel.org
Cc: devicetree@vger.kernel.org
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Yu Chen <chenyu56@huawei.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
In certain circumstances, the XHCI SuperSpeed instance in park mode
can fail to recover, thus on Amlogic G12A/G12B/SM1 SoCs when there is high
load on the single XHCI SuperSpeed instance, the controller can crash like:
xhci-hcd xhci-hcd.0.auto: xHCI host not responding to stop endpoint command.
xhci-hcd xhci-hcd.0.auto: Host halt failed, -110
xhci-hcd xhci-hcd.0.auto: xHCI host controller not responding, assume dead
xhci-hcd xhci-hcd.0.auto: xHCI host not responding to stop endpoint command.
hub 2-1.1:1.0: hub_ext_port_status failed (err = -22)
xhci-hcd xhci-hcd.0.auto: HC died; cleaning up
usb 2-1.1-port1: cannot reset (err = -22)
Setting the PARKMODE_DISABLE_SS bit in the DWC3_USB3_GUCTL1 mitigates
the issue. The bit is described as :
"When this bit is set to '1' all SS bus instances in park mode are disabled"
Synopsys explains:
The GUCTL1.PARKMODE_DISABLE_SS is only available in
dwc_usb3 controller running in host mode.
This should not be set for other IPs.
This can be disabled by default based on IP, but I recommend to have a
property to enable this feature for devices that need this.
CC: Dongjin Kim <tobetter@gmail.com>
Cc: Jianxin Pan <jianxin.pan@amlogic.com>
Cc: Thinh Nguyen <thinhn@synopsys.com>
Cc: Jun Li <lijun.kernel@gmail.com>
Reported-by: Tim <elatllat@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
When skipping TRBs, we need to account for wrapping around the ring
buffer and not modifying some invalid TRBs. Without this fix, dwc3 won't
be able to check for available TRBs.
Cc: stable <stable@vger.kernel.org>
Fixes: 7746a8dfb3 ("usb: dwc3: gadget: extract dwc3_gadget_ep_skip_trbs()")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
We track END_TRANSFER command completion. Don't clear transfer
started/ended flag prematurely. Otherwise, we'd run into the problem
with restarting transfer before END_TRANSFER command finishes.
Fixes: 6d8a019614 ("usb: dwc3: gadget: check for Missed Isoc from event status")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The main comment in the file mistakenly marked with kernel doc annotation
which makes the parser unhappy:
.../dwc3/host.c:16: warning: Function parameter or member 'dwc' not described in 'dwc3_host_get_irq'
Drop kernel doc annotation from host.c module.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The ACPI companion of the adapter has to be set for xHCI controller
code to read and attach the ports described in the ACPI table.
Use ACPI_COMPANION_SET macro to set this.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Exynos5422 DWC3 module support two clk USBD300 and SCLK_USBD300
so add missing code to enable/disable code and suspend clk, for this
add a new compatible samsung,exynos5420-dwusb3 to help configure
dwc3 code and dwc3 suspend clock. Suspend clock controls the PHY power
change from P0 to P1/P2/P3 during U0 to U1/U2/U3 transition.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Clang warns:
../drivers/usb/dwc3/dwc3-meson-g12a.c:421:6: warning: variable 'ret' is
used uninitialized whenever 'if' condition is false
[-Wsometimes-uninitialized]
if (priv->otg_mode == USB_DR_MODE_OTG) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../drivers/usb/dwc3/dwc3-meson-g12a.c:455:9: note: uninitialized use
occurs here
return ret;
^~~
../drivers/usb/dwc3/dwc3-meson-g12a.c:421:2: note: remove the 'if' if
its condition is always true
if (priv->otg_mode == USB_DR_MODE_OTG) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../drivers/usb/dwc3/dwc3-meson-g12a.c:415:9: note: initialize the
variable 'ret' to silence this warning
int ret, irq;
^
= 0
1 warning generated.
It is not wrong, ret is only used when that if statement is true. Just
directly return 0 at the end to avoid this.
Fixes: 729149c53f04 ("usb: dwc3: Add Amlogic A1 DWC3 glue")
Reported-by: kbuild test robot <lkp@intel.com>
Link: https://groups.google.com/d/msg/clang-built-linux/w5iBENco_m4/PPuXreAxBQAJ
Link: https://github.com/ClangBuiltLinux/linux/issues/869
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Pointer trb being assigned with a value that is never read, it is
assigned a new value later on. The assignment is redundant and
can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Variable status is being assigned with a value that is never read, it is
assigned a new value immediately afterwards. The assignment is redundant
and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
platform_get_irq() will call dev_err() itself on failure,
so there is no need for the driver to also do this.
This is detected by coccinelle.
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch introduces a new parameter to activate external ID pin and valid
vbus level detection, required on STM32MP15 SoC to support dual role,
either in HS or FS.
The STM32MP15 SoC uses the GGPIO register to enable the level detection.
The level detector requires to be powered.
Also adds the params structures for STM32MP15 OTG HS and STM32MP1 OTG FS.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Adds support for Amlogic A1 USB Control Glue HW.
The Amlogic A1 SoC Family embeds 1 USB Controllers:
- a DWC3 IP configured as Host for USB2 and USB3
A glue connects the controllers to the USB2 PHY of A1 SoC.
Signed-off-by: Yue Wang <yue.wang@amlogic.com>
Signed-off-by: Hanjie Lin <hanjie.lin@amlogic.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The MAX3420 is USB2.0 only, UDC-over-SPI controller. This driver
also supports the peripheral mode of MAX3421.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
By printing enqueue/dequeue pointers, we can make sure that our TRB
handling is correct. We've had a recent situation where we were not
always dequeueing all TRBs in an SG list and this helped figure out
what the problem was.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
In the same way as Intel Ice Lake TCSS (Type-C Subsystem) the Tiger Lake
TCSS xHCI needs to be runtime suspended whenever possible to allow the
TCSS hardware block to enter D3cold and thus save energy.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Depending on the current link state the steps to resume the link to U0
varies. The normal case when a port is suspended (U3) we set the link
to U0 and wait for a port event when U3exit completed and port moved to
U0.
If the port is in U1/U2, then no event is issued, just set link to U0
If port is in Resume or Recovery state then the device has already
initiated resume, and this host initiated resume is racing against it.
Port event handler for device initiated resume will set link to U0,
just wait for the port to reach U0 before returning.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like U3 case, xHCI spec doesn't specify the upper bound of U0 transition
time. The 20ms is not enough for some devices.
Intead of polling PLS or PLC, we can facilitate the port change event to
know that the link transits to U0 is completed.
While at it, also separate U0 and U3 case to make the code cleaner.
[variable rename to u3exit, and skip completion for usb2 ports -Mathias ]
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xHCI spec doesn't specify the upper bound of U3 transition time. For
some devices 20ms is not enough, so we need to make sure the link state
is in U3 before further actions.
I've tried to use U3 Entry Capability by setting U3 Entry Enable in
config register, however the port change event for U3 transition
interrupts the system suspend process.
For now let's use the less ideal method by polling PLS.
[use usleep_range(), and shorten the delay time while polling -Mathias]
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This PCIe controller chip is used on the Raspberry Pi 4 and multiple
adapter cards. There is no publicly available documentation for the
chip, yet both the downstream RPi4 kernel and the controller cards
support/advertise LPM support.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Additional debugging to show xHC USBSTS register when stop endpoint
command watchdog triggers and host is assumed dead.
useful to know the current status before the controller is stopped by
the xhci driver and everything is released and freed.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't show the same error message for transaction errors and split
transaction errors. It's very confusing while debugging.
Transaction errors are often due to electrical interference.
Split transaction errors are about xHC not being able to
schedule start and complete split transactions needed to address
low- and full-speed devices behind high-speed hubs.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bail out early if the xHC host needs to be reset at resume
but driver can't access xHC PCI registers.
If xhci driver already fails to reset the controller then there
is no point in attempting to free, re-initialize, re-allocate and
re-start the host. If failure to access the host is detected later,
failing the resume, xhci interrupts will be double freed
when remove is called.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a device id for HP LD381 Display
LD381: 03f0:0f7f
Signed-off-by: Scott Chen <scott@labau.com.tw>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
In case there are multiple Marvell EHCI blocks in system, we need a
different bus name for each one. Otherwise debugfs gets mildly upset about
a directory name in usb/ehci:
debugfs: Directory 'mv ehci' with parent 'ehci' already present!
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200309130014.548168-2-lkundrak@v3.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Turns out the undocumented and reserved bits of port status/control
register of the root port need to be set to use the HCI in HSIC mode.
Typically the firmware does this, but that is not always good enough,
because the bits get lost if the HSIC clock is disabled (e.g. when
ehci-mv is build as a module).
This supplements commit 7b104f890a ("USB: EHCI: ehci-mv: add HSIC
support").
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200309130014.548168-1-lkundrak@v3.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NVIDIA VirtualLink (svid 0x955) has two altmode, vdo=0x1 for
VirtualLink DP mode and vdo=0x3 for NVIDIA test mode. NVIDIA
test device FTB (Function Test Board) reports altmode list with
vdo=0x3 first and then vdo=0x1. The list is:
SVID VDO
0xff01 0xc05
0x28de 0x8085
0x955 0x3
0x955 0x1
Current logic to assign mode value is based on order
in altmode list. This causes a mismatch of CON and SOP altmodes
since NVIDIA GPU connector has order of vdo=0x1 first and then
vdo=0x3. Fixing this by changing the order of vdo values
reported by NVIDIA test device. the new list will be:
SVID VDO
0xff01 0xc05
0x28de 0x8085
0x955 0x1085
0x955 0x3
Also NVIDIA VirtualLink (svid 0x955) uses pin E for display mode.
NVIDIA test device reports vdo of 0x1 so make sure vdo values
always have pin E assignement.
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200310121912.57879-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200311093003.24604-1-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When loading new kernel via kexec, we need to shutdown host controller to
avoid any un-expected memory accessing during new kernel boot.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Cc: stable <stable@vger.kernel.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200306092328.41253-1-ran.wang_1@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Locking the connector in ucsi_register_displayport() to make
sure that nothing can access the displayport alternate mode
before the function has finished and the alternate mode is
actually ready.
Fixes: af8622f6a5 ("usb: typec: ucsi: Support for DisplayPort alt mode")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200311130006.41288-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the registration of the DisplayPort was not successful,
or if the port does not support DisplayPort alt mode in the
first place, the function ucsi_displayport_remove_partner()
will fail with NULL pointer dereference when it attempts to
access the driver data.
Adding a check to the function to make sure there really is
driver data for the device before modifying it.
Fixes: af8622f6a5 ("usb: typec: ucsi: Support for DisplayPort alt mode")
Reported-by: Andrea Gagliardi La Gala <andrea.lagala@gmail.com>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=206365
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200311130006.41288-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Realtek Hub (0bda:0x0487) used in Dell Dock WD19 sometimes drops off the
bus when bringing underlying ports from U3 to U0.
Disabling LPM on the hub during setting link state is not enough, so
let's disable LPM completely for this hub.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200205112633.25995-3-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the struct tty_port pointer and rename the struct usb_serial_port
pointer "port", which is the named used throughout the subsystem and
incidentally also matches the kernel-doc comment.
Signed-off-by: Johan Hovold <johan@kernel.org>
This controller timeouts during suspend (S3) with
[ 240.521724] xhci_hcd 0000:30:00.3: WARN: xHC save state timeout
[ 240.521729] xhci_hcd 0000:30:00.3: ERROR mismatched command completion event
thus preventing the system from entering S3.
Moreover it remains in an undefined state where some connected devices stop
working until a reboot.
Apply the XHCI_SUSPEND_DELAY quirk to make it suspend properly.
CC: stable@vger.kernel.org
Signed-off-by: Alberto Mattea <alberto@mattea.info>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200306150858.21904-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
libtraceevent (used by perf and trace-cmd) failed to parse the
xhci_urb_dequeue trace event. This is because the user space trace
event format parsing is not a full C compiler. It can handle some basic
logic, but is not meant to be able to handle everything C can do.
In cases where a trace event field needs to be converted from a number
to a string, there's the __print_symbolic() macro that should be used:
See samples/trace_events/trace-events-sample.h
Some xhci trace events open coded the __print_symbolic() causing the
user spaces tools to fail to parse it. This has to be replaced with
__print_symbolic() instead.
CC: stable@vger.kernel.org
Reported-by: Tzvetomir Stoyanov <tstoyanov@vmware.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=206531
Fixes: 5abdc2e6e1 ("usb: host: xhci: add urb_enqueue/dequeue/giveback tracers")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200306150858.21904-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Intel PMC microcontroller on the latest Intel platforms
has a new function that allows configuration of the USB
Multiplexer/DeMultiplexer switches that are under the
control of the PMC.
The Intel PMC mux control (aka. mux-agent) can be used for
swapping the USB data role and for entering alternate modes,
DisplayPort or Thunderbolt3.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200302135353.56659-10-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The switch devices have been named by using the name of the
parent device as base for now, but if for example the
parent device controls multiple muxes, that will not work.
Adding an optional member "name" to the switch descriptor
that can be used for naming the switch during registration.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200302135353.56659-7-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB role callback functions had a parameter pointing to
the parent device (struct device) of the switch. The
assumption was that the switch parent is always the
controller. Firstly, that may not be true in every case, and
secondly, it prevents us from supporting devices that supply
multiple muxes.
Changing the first parameter of usb_role_switch_set_t and
usb_role_switch_get_t from struct device to struct
usb_role_switch.
Cc: Peter Chen <Peter.Chen@nxp.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Bin Liu <b-liu@ti.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200302135353.56659-6-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding usb_role_switch_get/set_drvdata() functions that the
switch drivers can use for setting and getting private data
pointer that is associated with the switch.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200302135353.56659-5-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introducing fwnode_typec_switch_get() and
fwnode_typec_mux_get() functions that work just like
typec_switch_get() and typec_mux_get() but they take struct
fwnode_handle as the first parameter instead of struct
device.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200302135353.56659-4-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding helpers typec_switch_set() and typec_mux_set() that
simply call the ->set callback function of the mux. These
functions make it possible to set the mux states also from
outside the class code.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200302135353.56659-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mux devices have been named by using the name of the
parent device as base until now, but if for example the
parent device has multiple muxes that will not work. This
makes it possible to supply the name for a mux during
registration.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200302135353.56659-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If scatter-gather operation is allowed, a large USB request is split
into multiple TRBs. For preparing TRBs for sg list, driver iterates
over the list and creates TRB for each sg and mark the chain bit to
false for the last sg. The current IOMMU driver is clubbing the list
of sgs which shares a page boundary into one and giving it to USB driver.
With this the number of sgs mapped it not equal to the the number of sgs
passed. Because of this USB driver is not marking the chain bit to false
since it couldn't iterate to the last sg. This patch addresses this issue
by marking the chain bit to false if it is the last mapped sg.
At a practical level, this patch resolves USB transfer stalls
seen with adb on dwc3 based db845c, pixel3 and other qcom
hardware after functionfs gadget added scatter-gather support
around v4.20.
Credit also to Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
who implemented a very similar fix to this issue.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Yang Fei <fei.yang@intel.com>
Cc: Thinh Nguyen <thinhn@synopsys.com>
Cc: Tejas Joglekar <tejas.joglekar@synopsys.com>
Cc: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: Todd Kjos <tkjos@google.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Linux USB List <linux-usb@vger.kernel.org>
Cc: stable <stable@vger.kernel.org> #4.20+
Signed-off-by: Pratham Pratap <prathampratap@codeaurora.org>
[jstultz: Slight tweak to remove sg_is_last() usage, reworked
commit message, minor comment tweak]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Link: https://lore.kernel.org/r/20200302214443.55783-1-john.stultz@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewing a fresh portion of coverity defects in USB core
(specifically CID 1458999), Alan Stern noted below in [1]:
On Tue, Feb 25, 2020 at 02:39:23PM -0500, Alan Stern wrote:
> A revised search finds line 997 in drivers/usb/core/hub.c and lines
> 216, 269 in drivers/usb/core/port.c. (I didn't try looking in any
> other directories.) AFAICT all three of these should check the
> return value, although a error message in the kernel log probably
> isn't needed.
Factor out the usb_port_runtime_{resume,suspend}() changes into a
standalone patch to allow conflict-free porting on top of stable v3.9+.
[1] https://lore.kernel.org/lkml/Pine.LNX.4.44L0.2002251419120.1485-100000@iolanthe.rowland.org
Fixes: 971fcd492c ("usb: add runtime pm support for usb port device")
Cc: stable@vger.kernel.org # v3.9+
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200226175036.14946-3-erosca@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewing a fresh portion of coverity defects in USB core
(specifically CID 1458999), Alan Stern noted below in [1]:
On Tue, Feb 25, 2020 at 02:39:23PM -0500, Alan Stern wrote:
> A revised search finds line 997 in drivers/usb/core/hub.c and lines
> 216, 269 in drivers/usb/core/port.c. (I didn't try looking in any
> other directories.) AFAICT all three of these should check the
> return value, although a error message in the kernel log probably
> isn't needed.
Factor out the usb_remove_device() change into a standalone patch to
allow conflict-free integration on top of the earliest stable branches.
[1] https://lore.kernel.org/lkml/Pine.LNX.4.44L0.2002251419120.1485-100000@iolanthe.rowland.org
Fixes: 253e05724f ("USB: add a "remove hardware" sysfs attribute")
Cc: stable@vger.kernel.org # v2.6.33+
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200226175036.14946-2-erosca@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Address below Coverity complaint (Feb 25, 2020, 8:06 AM CET):
*** CID 1458999: Error handling issues (CHECKED_RETURN)
/drivers/usb/core/hub.c: 1869 in hub_probe()
1863
1864 if (id->driver_info & HUB_QUIRK_CHECK_PORT_AUTOSUSPEND)
1865 hub->quirk_check_port_auto_suspend = 1;
1866
1867 if (id->driver_info & HUB_QUIRK_DISABLE_AUTOSUSPEND) {
1868 hub->quirk_disable_autosuspend = 1;
>>> CID 1458999: Error handling issues (CHECKED_RETURN)
>>> Calling "usb_autopm_get_interface" without checking return value (as is done elsewhere 97 out of 111 times).
1869 usb_autopm_get_interface(intf);
1870 }
1871
1872 if (hub_configure(hub, &desc->endpoint[0].desc) >= 0)
1873 return 0;
1874
Rather than checking the return value of 'usb_autopm_get_interface()',
switch to the usb_autopm_get_interface_no_resume() API, as per:
On Tue, Feb 25, 2020 at 10:32:32AM -0500, Alan Stern wrote:
------ 8< ------
> This change (i.e. 'ret = usb_autopm_get_interface') is not necessary,
> because the resume operation cannot fail at this point (interfaces
> are always powered-up during probe). A better solution would be to
> call usb_autopm_get_interface_no_resume() instead.
------ 8< ------
Fixes: 1208f9e1d7 ("USB: hub: Fix the broken detection of USB3 device in SMSC hub")
Cc: Hardik Gajjar <hgajjar@de.adit-jv.com>
Cc: stable@vger.kernel.org # v4.14+
Reported-by: scan-admin@coverity.com
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200226175036.14946-1-erosca@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current driver has 240 (USB2.0) and 2048 (USB3.0) as max_sectors,
e.g., /sys/bus/scsi/devices/0:0:0:0/max_sectors
If data access times out, driver error handling will issue a port
reset.
Sometimes Samsung Fit (090C:1000) flash disk will not respond to
later Set Address or Get Descriptor command.
Adding this quirk to limit max_sectors to 64 sectors to avoid issue
occurring.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1583158895-31342-1-git-send-email-jilin@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LPM on the device appears to cause xHCI host controllers to claim
that there isn't enough bandwidth to support additional devices.
Signed-off-by: Dan Lazewatsky <dlaz@chromium.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Link: https://lore.kernel.org/r/20200226143438.1445-1-gustavo.padovan@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 4d7201cda2 ("usb: usb251xb: add vdd supply support") didn't
covered the non-DT use-case and so the regualtor_enable() call during
probe will fail on those platforms. Also the commit didn't handled the
error case correctly.
Move devm_regulator_get() out of usb251xb_get_ofdata() to address the
1st issue. This can be done without worries because devm_regulator_get()
handles the non-DT use-case too. Add devm_add_action_or_reset() to
address the 2nd bug.
Fixes: 4d7201cda2 ("usb: usb251xb: add vdd supply support")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Acked-by: Richard Leitner <richard.leitner@skidata.com>
Link: https://lore.kernel.org/r/20200226072644.18490-1-m.felsch@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If there are TRBs pending during reset endpoint operation, the
DMA will advance after reset operation, but it isn't expected,
since the data is not yet available (For OUT, the data is not
yet available). After the data is ready, there won't be any
interrupt since the EP_TRADDR already points to next TRB entry
and doorbell is not set.
To fix it, it toggles cycle bit before reset operation, and restores
it after reset, it could avoid unexpected DMA advance due to
cycle bit is for software during the endpoint reset operation.
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200219141455.23257-3-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It has marked the dequeue trb as link trb, but its next segment
pointer is still itself, it causes the transfer can't go on. Fix
it by set its pointer as the trb address for the next request.
Fixes: f616c3bda4 ("usb: cdns3: Fix dequeue implementation")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200219141455.23257-2-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Per typec spec:
Figure 4-15 Connection State Diagram: DRP
Figure 4-16 Connection State Diagram: DRP with Accessory and Try.SRC
Support
Figure 4-17 Connection State Diagram: DRP with Accessory and Try.SNK
Support
DRP port should move to Unattached.SNK instead of Unattached.SRC if
sink removed.
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1582128343-22438-1-git-send-email-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver uses only GPIO Descriptor Consumer Interface so include
proper header. This fixes compile test failures (e.g. on i386):
drivers/usb/phy/phy-tegra-usb.c: In function ‘ulpi_phy_power_on’:
drivers/usb/phy/phy-tegra-usb.c:695:2: error:
implicit declaration of function ‘gpiod_set_value_cansleep’ [-Werror=implicit-function-declaration]
drivers/usb/phy/phy-tegra-usb.c: In function ‘tegra_usb_phy_probe’:
drivers/usb/phy/phy-tegra-usb.c:1167:11: error:
implicit declaration of function ‘devm_gpiod_get_from_of_node’ [-Werror=implicit-function-declaration]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/1583234960-24909-1-git-send-email-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variables declared in a switch statement before any case statements
cannot be automatically initialized with compiler instrumentation (as
they are not part of any execution flow). With GCC's proposed automatic
stack variable initialization feature, this triggers a warning (and they
don't get initialized). Clang's automatic stack variable initialization
(via CONFIG_INIT_STACK_ALL=y) doesn't throw a warning, but it also
doesn't initialize such variables[1]. Note that these warnings (or silent
skipping) happen before the dead-store elimination optimization phase,
so even when the automatic initializations are later elided in favor of
direct initializations, the warnings remain.
To avoid these problems, move such variables into the "case" where
they're used or lift them up into the main function body.
drivers/usb/gadget/udc/net2280.c: In function ‘handle_stat0_irqs_superspeed’:
drivers/usb/gadget/udc/net2280.c:2871:22: warning: statement will never be executed [-Wswitch-unreachable]
2871 | struct net2280_ep *e;
| ^
[1] https://bugs.llvm.org/show_bug.cgi?id=44916
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/202002201515.DFC51CF@keescook
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't confuse user with meaningless warning about the failure in getting
supplies in case of deferred probe.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200228092808.4580-1-m.szyprowski@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Fintek F81532A/534A/535/536 is USB-to-2/4/8/12 serial ports device
and the serial ports are default disabled. Each port contains max 3 pins
GPIO and the 3 pins are default pull high with input mode.
When the serial port had activated (running probe()), we'll transform the
3 pins from GPIO function publicly to control Tranceiver privately use.
We'll default set to 0/0/1 for control transceiver to RS232 mode.
Otherwise, If the serial port is not active, the 3 pins is in GPIO mode
and controlled by global GPIO device with VID/PID: 2c42/16f8.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The Fintek F81532A/534A/535/536 is USB-to-2/4/8/12 serial ports device
and the serial port is default disabled when plugin computer.
The IC is contains devices as following:
1. HUB (all devices is connected with this hub)
2. GPIO/Control device. (enable serial port and control GPIOs)
3. serial port 1 to x (2/4/8/12)
It's most same with F81232, the UART device is difference as follow:
1. TX/RX bulk size is 128/512bytes
2. RX bulk layout change:
F81232: [LSR(1Byte)+DATA(1Byte)][LSR(1Byte)+DATA(1Byte)]...
F81534A:[LEN][Data.....][LSR]
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
[johan: reword an error message]
Signed-off-by: Johan Hovold <johan@kernel.org>
Use devm_kzalloc() to replace kzalloc() in port_probe().
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add tx_empty() function for F81232. Without this, console redirection will
get garbage data.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Extract LSR handler to function that can be re-used by
F81532A/534A/535/536.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
'GRABBER' is a weird name, all other types map to the /dev
device names. Rename to 'VIDEO' to be consistent with the
other types.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20200220132017.GA29262@embeddedor
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
device_driver name is const char pointer, so it not useful to cast
udc_name (which is already const char).
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Link: https://lore.kernel.org/r/1582054383-35760-15-git-send-email-clabbe@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
device_driver name is const char pointer, so it not useful to cast
udc_name (which is already const char).
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Link: https://lore.kernel.org/r/1582054383-35760-14-git-send-email-clabbe@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
device_driver name is const char pointer, so it not useful to cast
driver_name (which is already const char).
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Link: https://lore.kernel.org/r/1582054383-35760-10-git-send-email-clabbe@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
device_driver name is const char pointer, so it not useful to cast
driver_name (which is already const char).
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Link: https://lore.kernel.org/r/1582054383-35760-5-git-send-email-clabbe@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Compiler is not happy about dangling variable:
.../core/usb-acpi.c: In function ‘usb_acpi_get_connect_type’:
.../core/usb-acpi.c:90:14: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
90 | acpi_status status;
| ^~~~~~
Make use of it by checking the status and bail out in case of error.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200218185207.62527-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After this was made buildable for something other than PPC32, kbuild
starts warning
drivers/usb/host/fhci-hcd.c:398:8: warning: this statement may fall
through [-Wimplicit-fallthrough=]
I don't know this code, but from the construction (initializing size
with 0 and explicitly using "size +=" in the PIPE_BULK case) I assume
that fallthrough is indeed intended.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Li Yang <leoyang.li@nxp.com>
Link: https://lore.kernel.org/r/20200213085401.27862-1-linux@rasmusvillemoes.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ucsi ppm is unregistered during fw flashing so disable
runtime pm also and reenable after fw flashing is completed
and ppm is re-registered.
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200217144913.55330-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NVIDIA VirtualLink (svid 0x955) has two altmode, vdo=0x1 for
VirtualLink DP mode and vdo=0x3 for NVIDIA test mode.
Register display altmode driver only for vdo=0x1
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200217144913.55330-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new device id for the 100 devie. It has 4 interfaces like the 28
and 28L devices but a larger endpoint so more I/O pins.
Cc: Christoph Jung <jung@codemercs.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200214161148.GA3963518@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sparse reports a warning at xhci_enter_test_mode()
warning: context imbalance in xhci_enter_test_mode - unexpected unlock
The root cause is the missing annotation at xhci_enter_test_mode()
Add the missing __must_hold(&xhci->lock) annotattion
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Link: https://lore.kernel.org/r/20200214204741.94112-24-jbi.octave@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sparse reports a warning at xhci_set_port_power()
warning: context imbalance in xhci_set_port_power - unexpected unlock
The root cause is the missing annotation at xhci_set_port_power()
Add the missing __must_hold(&xhci->lock) annotattion
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Link: https://lore.kernel.org/r/20200214204741.94112-23-jbi.octave@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
libtraceevent (used by perf and trace-cmd) failed to parse the
xhci_urb_dequeue trace event. This is because the user space trace
event format parsing is not a full C compiler. It can handle some basic
logic, but is not meant to be able to handle everything C can do.
In cases where a trace event field needs to be converted from a number
to a string, there's the __print_symbolic() macro that should be used:
See samples/trace_events/trace-events-sample.h
Some xhci trace events open coded the __print_symbolic() causing the
user spaces tools to fail to parse it. This has to be replaced with
__print_symbolic() instead.
CC: stable@vger.kernel.org
Reported-by: Tzvetomir Stoyanov <tstoyanov@vmware.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=206531
Fixes: 5abdc2e6e1 ("usb: host: xhci: add urb_enqueue/dequeue/giveback tracers")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Link: https://lore.kernel.org/r/20200214115634.30e8ebf2@gandalf.local.home
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertenly introduced[3] to the codebase from now on.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20200211232303.GA21495@embeddedor
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertenly introduced[3] to the codebase from now on.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20200211232519.GA23263@embeddedor
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the typec port data role is separated from power role,
so check the port data capability when setting data role.
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/1581666828-2063-1-git-send-email-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Call cpu_latency_qos_add/remove_request() instead of
pm_qos_add/remove_request(), respectively, because the
latter are going to be dropped.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
DWC3 learned that we can't always depend on Event Status bits. A
problem was solved which would only surface with scatter list on IN
endpoints.
DWC2 got a fix for feature requests (both set and clear) and GetStatus
request.
The serial gadget got a fix for a TX stall bug.
Composite framework now works better for SSP devices.
-----BEGIN PGP SIGNATURE-----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=n8Hd
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
USB: fixes for v5.6-rc1
DWC3 learned that we can't always depend on Event Status bits. A
problem was solved which would only surface with scatter list on IN
endpoints.
DWC2 got a fix for feature requests (both set and clear) and GetStatus
request.
The serial gadget got a fix for a TX stall bug.
Composite framework now works better for SSP devices.
* tag 'fixes-for-v5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
usb: dwc3: debug: fix string position formatting mixup with ret and len
usb: gadget: serial: fix Tx stall after buffer overflow
usb: gadget: ffs: ffs_aio_cancel(): Save/restore IRQ flags
usb: dwc2: Fix SET/CLEAR_FEATURE and GET_STATUS flows
usb: dwc2: Fix in ISOC request length checking
usb: gadget: composite: Support more than 500mA MaxPower
usb: gadget: composite: Fix bMaxPower for SuperSpeedPlus
usb: gadget: u_audio: Fix high-speed max packet size
usb: dwc3: gadget: Check for IOC/LST bit in TRB->ctrl fields
The product ID is little endian and needs to be converted.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200213111336.32392-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's a fix for a ch341 regression in 5.5 which people have started to
hit, and a fix for a logic error in an ir-usb error path.
Both have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXkUsAQAKCRALxc3C7H1l
CF+cAP9CPo+dy0rMGKPWkqGfLInimD6pMheJYe3gUZ4xgcbMkQEA+J3u3wYJQ7ND
Ia/KRCMV+mvvQTv9skejnd5K94TsVQ8=
=EY3I
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.6-rc2' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.6-rc2
Here's a fix for a ch341 regression in 5.5 which people have started to
hit, and a fix for a logic error in an ir-usb error path.
Both have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-5.6-rc2' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: ch341: fix receiver regression
USB: serial: ir-usb: Silence harmless uninitialized variable warning
iOS devices will not draw more than 500mA unless instructed to do so.
Setting the charge type power supply property to "fast" tells the device
to start drawing more power, using the same procedure that official
"MFi" chargers would.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20191016093933.693-7-hadess@hadess.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If ->probe fails for a device specific driver, ask the driver core to
reprobe us, after having flagged the device for the generic driver to be
forced.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20191016093933.693-6-hadess@hadess.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that USB device drivers can reuse code from the generic USB device
driver, we need to make sure that they get selected rather than the
generic driver. Add an id_table and match vfunc to the usb_device_driver
struct, which will get used to select a better matching driver at
->probe time.
This is a similar mechanism to that used in the HID drivers, with the
generic driver being selected unless there's a better matching one found
in the registered drivers (see hid_generic_match() in
drivers/hid/hid-generic.c).
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20191016093933.693-5-hadess@hadess.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Match a usb_device with a table of IDs.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20191016093933.693-4-hadess@hadess.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel currenly has only 2 usb_device_drivers, one generic one, one
that completely replaces the generic one to make USB devices usable over
a network.
Use the newly exported generic driver functions when a driver declares
to want them run, in addition to its own code. This makes it possible to
write drivers that extend the generic USB driver.
Note that this patch is not enough for another driver to automatically
get selected.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20191016093933.693-3-hadess@hadess.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This will make it possible to implement device drivers which extend the
generic driver without needing to reimplement it.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20191016093933.693-2-hadess@hadess.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertenly introduced[3] to the codebase from now on.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20200211232148.GA20644@embeddedor
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using the generic notification chain is not reasonable with
the alternate modes because it would require dependencies
between the drivers of the components that need the
notifications, and the typec drivers.
There are no users for the alternate mode notifications, so
removing the chain and the API for it completely.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200211112531.86510-6-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even though originally the USB Type-C Specification did not
describe the steps for power role swapping without USB PD
contract in place, it did not actually mean power role swap
without USB PD was not allowed. The USB Type-C Specification
did not clearly separate the data and power roles until in
the release 1.2 which is why there also were no clear steps
for the scenario where only the power role was swapped
without USB PD contract before that.
Since in the latest version of the specification the power
role swap without USB PD is now clearly mentioned as allowed
operation, removing the check that prevented power role swap
without USB PD support.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200211112531.86510-4-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port_type attribute is special. It is meant to allow
changing the capability of the port in runtime. It is purely
Linux kernel specific feature, i.e. the feature is not
described in any of the USB specifications.
Because of the special nature of this attribute, handling it
differently compared to the other writable attributes, and
hiding it when the underlying port interface (or just the
driver) does not support the feature.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200211112531.86510-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This affects the read-writable attribute files. Before this
there was no way for the user to know is changing the value
supported or not.
>From now on those attribute files will be made read-only
unless the underlying driver supports changing of the value.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200211112531.86510-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DWC3 USB driver is not a clock provider, and just needs to call
of_clk_get_parent_count().
Hence it can include <linux/of_clk.h> instead of <linux/clk-provider.h>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20200212101853.9349-1-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add new device ids for the 28 and 28L devices. These have 4 interfaces
instead of 2, but the driver binds the same, so the driver changes are
minimal.
Cc: Christoph Jung <jung@codemercs.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200212040422.2991-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for two OEM devices that are identical to existing
IO-Warrior devices, except for the USB device id.
Cc: Christoph Jung <jung@codemercs.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200212040422.2991-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the SourceControl will stay in power-down mode after resuming
from suspend. This patch resets the device after suspend to power it up.
Signed-off-by: Richard Dodd <richard.o.dodd@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200212142220.36892-1-richard.o.dodd@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci driver assumed that xHC controllers have at most one custom
supported speed table (PSI) for all usb 3.x ports.
Memory was allocated for one PSI table under the xhci hub structure.
Turns out this is not the case, some controllers have a separate
"supported protocol capability" entry with a PSI table for each port.
This means each usb3 roothub port can in theory support different custom
speeds.
To solve this, cache all supported protocol capabilities with their PSI
tables in an array, and add pointers to the xhci port structure so that
every port points to its capability entry in the array.
When creating the SuperSpeedPlus USB Device Capability BOS descriptor
for the xhci USB 3.1 roothub we for now will use only data from the
first USB 3.1 capable protocol capability entry in the array.
This could be improved later, this patch focuses resolving
the memory leak.
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reported-by: Sajja Venkateswara Rao <VenkateswaraRao.Sajja@amd.com>
Fixes: 47189098f8 ("xhci: parse xhci protocol speed ID list for usb 3.1 usage")
Cc: stable <stable@vger.kernel.org> # v4.4+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200211150158.14475-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit fc57313d10.
Marek reports that it breaks things:
This patch landed in today's linux-next (20200211) and causes
NULL pointer dereference during second suspend/resume cycle on
Samsung Exynos5422-based (arm 32bit) Odroid XU3lite board:
A more complete fix will be added soon.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: fc57313d10 ("xhci: Fix memory leak when caching protocol extended capability PSI tables")
Cc: Paul Menzel <pmenzel@molgen.mpg.de>
Cc: Sajja Venkateswara Rao <VenkateswaraRao.Sajja@amd.com>
Cc: stable <stable@vger.kernel.org> # v4.4+
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the string formatting is mixing up the offset of ret and
len. Re-work the code to use just len, remove ret and use scnprintf
instead of snprintf and len position accumulation where required.
Remove the -ve return check since scnprintf never returns a failure
-ve size. Also break overly long lines to clean up checkpatch
warnings.
Addresses-Coverity: ("Unused value")
Fixes: 1381a5113c ("usb: dwc3: debug: purge usage of strcat")
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Symptom: application opens /dev/ttyGS0 and starts sending (writing) to
it while either USB cable is not connected, or nobody listens on the
other side of the cable. If driver circular buffer overflows before
connection is established, no data will be written to the USB layer
until/unless /dev/ttyGS0 is closed and re-opened again by the
application (the latter besides having no means of being notified about
the event of establishing of the connection.)
Fix: on open and/or connect, kick Tx to flush circular buffer data to
USB layer.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
ffs_aio_cancel() can be called from both interrupt and thread context. Make
sure that the current IRQ state is saved and restored by using
spin_{un,}lock_irq{save,restore}().
Otherwise undefined behavior might occur.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
SET/CLEAR_FEATURE for Remote Wakeup allowance not handled correctly.
GET_STATUS handling provided not correct data on DATA Stage.
Issue seen when gadget's dr_mode set to "otg" mode and connected
to MacOS.
Both are fixed and tested using USBCV Ch.9 tests.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Fixes: fa389a6d77 ("usb: dwc2: gadget: Add remote_wakeup_allowed flag")
Tested-by: Jack Mitchell <ml@embed.me.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Moved ISOC request length checking from dwc2_hsotg_start_req() function to
dwc2_hsotg_ep_queue().
Fixes: 4fca54aa58 ("usb: gadget: s3c-hsotg: add multi count support")
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
USB 3.x SuperSpeed peripherals can draw up to 900mA of VBUS power
when in configured state. However, if a configuration wanting to
take advantage of this is added with MaxPower greater than 500
(currently possible if using a ConfigFS gadget) the composite
driver fails to accommodate this for a couple reasons:
- usb_gadget_vbus_draw() when called from set_config() and
composite_resume() will be passed the MaxPower value without
regard for the current connection speed, resulting in a
violation for USB 2.0 since the max is 500mA.
- the bMaxPower of the configuration descriptor would be
incorrectly encoded, again if the connection speed is only
at USB 2.0 or below, likely wrapping around U8_MAX since
the 2mA multiplier corresponds to a maximum of 510mA.
Fix these by adding checks against the current gadget->speed
when the c->MaxPower value is used (set_config() and
composite_resume()) and appropriately limit based on whether
it is currently at a low-/full-/high- or super-speed connection.
Because 900 is not divisible by 8, with the round-up division
currently used in encode_bMaxPower() a MaxPower of 900mA will
result in an encoded value of 0x71. When a host stack (including
Linux and Windows) enumerates this on a single port root hub, it
reads this value back and decodes (multiplies by 8) to get 904mA
which is strictly greater than 900mA that is typically budgeted
for that port, causing it to reject the configuration. Instead,
we should be using the round-down behavior of normal integral
division so that 900 / 8 -> 0x70 or 896mA to stay within range.
And we might as well change it for the high/full/low case as well
for consistency.
N.B. USB 3.2 Gen N x 2 allows for up to 1500mA but there doesn't
seem to be any any peripheral controller supported by Linux that
does two lane operation, so for now keeping the clamp at 900
should be fine.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
SuperSpeedPlus peripherals must report their bMaxPower of the
configuration descriptor in units of 8mA as per the USB 3.2
specification. The current switch statement in encode_bMaxPower()
only checks for USB_SPEED_SUPER but not USB_SPEED_SUPER_PLUS so
the latter falls back to USB 2.0 encoding which uses 2mA units.
Replace the switch with a simple if/else.
Fixes: eae5820b85 ("usb: gadget: composite: Write SuperSpeedPlus config descriptors")
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Prior to commit eb9fecb9e6 ("usb: gadget: f_uac2: split out audio
core") the maximum packet size was calculated only from the high-speed
descriptor but now we use the largest of the full-speed and high-speed
descriptors.
This is correct, but the full-speed value is likely to be higher than
that for high-speed and this leads to submitting requests for OUT
transfers (received by the gadget) which are larger than the endpoint's
maximum packet size. These are rightly rejected by the gadget core.
config_ep_by_speed() already sets up the correct maximum packet size for
the enumerated speed in the usb_ep structure, so we can simply use this
instead of the overall value that has been used to allocate buffers for
requests.
Note that the minimum period for ALSA is still set from the largest
value, and this is unavoidable because it's possible to open the audio
device before the gadget has been enumerated.
Tested-by: Pavel Hofman <pavel.hofman@ivitera.com>
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The current code in dwc3_gadget_ep_reclaim_completed_trb() will
check for IOC/LST bit in the event->status and returns if
IOC/LST bit is set. This logic doesn't work if multiple TRBs
are queued per request and the IOC/LST bit is set on the last
TRB of that request.
Consider an example where a queued request has multiple queued
TRBs and IOC/LST bit is set only for the last TRB. In this case,
the core generates XferComplete/XferInProgress events only for
the last TRB (since IOC/LST are set only for the last TRB). As
per the logic in dwc3_gadget_ep_reclaim_completed_trb()
event->status is checked for IOC/LST bit and returns on the
first TRB. This leaves the remaining TRBs left unhandled.
Similarly, if the gadget function enqueues an unaligned request
with sglist already in it, it should fail the same way, since we
will append another TRB to something that already uses more than
one TRB.
To aviod this, this patch changes the code to check for IOC/LST
bits in TRB->ctrl instead.
At a practical level, this patch resolves USB transfer stalls seen
with adb on dwc3 based HiKey960 after functionfs gadget added
scatter-gather support around v4.20.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Yang Fei <fei.yang@intel.com>
Cc: Thinh Nguyen <thinhn@synopsys.com>
Cc: Tejas Joglekar <tejas.joglekar@synopsys.com>
Cc: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: Todd Kjos <tkjos@google.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Linux USB List <linux-usb@vger.kernel.org>
Cc: stable <stable@vger.kernel.org>
Tested-by: Tejas Joglekar <tejas.joglekar@synopsys.com>
Reviewed-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
[jstultz: forward ported to mainline, reworded commit log, reworked
to only check trb->ctrl as suggested by Felipe]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Pointer trb being assigned with a value that is never read, it is
assigned a new value later on. The assignment is redundant and
can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200208161802.28846-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable status is being assigned with a value that is never read, it is
assigned a new value immediately afterwards. The assignment is redundant
and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200208163132.29592-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable num is being assigned with a value that is never read, it is
assigned a new value later in a for-loop. The assignment is redundant
and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200208165022.30429-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since EHCI/OHCI controllers on R-Car Gen3 SoCs are possible to
be getting stuck very rarely after a full/low usb device was
disconnected. To detect/recover from such a situation, the controllers
require a special way which poll the EHCI PORTSC register and changes
the OHCI functional state.
So, this patch adds a polling timer into the ehci-platform driver,
and if the ehci driver detects the issue by the EHCI PORTSC register,
the ehci driver removes a companion device (= the OHCI controller)
to change the OHCI functional state to USB Reset once. And then,
the ehci driver adds the companion device again.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/1580114262-25029-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new usb-device pointer instead of back-casting when accessing
the struct usb_device when parsing endpoints.
Note that this introduces two lines that are longer than 80 chars on
purpose.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200203153830.26394-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new device quirk that can be used to blacklist endpoints.
Since commit 3e4f8e21c4 ("USB: core: fix check for duplicate
endpoints") USB core ignores any duplicate endpoints found during
descriptor parsing.
In order to handle devices where the first interfaces with duplicate
endpoints are the ones that should have their endpoints ignored, we need
to add a blacklist.
Tested-by: edes <edes@gmx.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200203153830.26394-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the string formatting is mixing up the offset of ret and
len. Re-work the code to use just len, remove ret and use scnprintf
instead of snprintf and len position accumulation where required.
Remove the -ve return check since scnprintf never returns a failure
-ve size. Also break overly long lines to clean up checkpatch
warnings.
Addresses-Coverity: ("Unused value")
Fixes: 1381a5113c ("usb: dwc3: debug: purge usage of strcat")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200210095139.328711-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tools like Coccinelle may erroneously recommend to use the
devm_platform_ioremap_resource() API for the registers mapping because
these tools are not aware about the implementation details of the driver.
Let's add a clarifying comments to the code, which should help to stop
future attempts to break the driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200202224259.29187-1-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paul Zimmerman reports that his USB Bluetooth adapter sometimes
crashes following system resume, when it receives a
Get-Device-Descriptor request while it is busy doing something else.
Such a request was added by commit a4f55d8b8c ("usb: hub: Check
device descriptor before resusciation"). It gets sent when the hub
driver's work thread checks whether a connect-change event on an
enabled port really indicates a new device has been connected, as
opposed to an old device momentarily disconnecting and then
reconnecting (which can happen with xHCI host controllers, since they
automatically enable connected ports).
The same kind of thing occurs when a port's power session is lost
during system suspend. When the system wakes up it sees a
connect-change event on the port, and if the child device's
persist_enabled flag was set then hub_activate() sets the device's
reset_resume flag as well as the port's bit in hub->change_bits. The
reset-resume code then takes responsibility for checking that the same
device is still attached to the port, and it does this as part of the
device's resume pathway. By the time the hub driver's work thread
starts up again, the device has already been fully reinitialized and
is busy doing its own thing. There's no need for the work thread to
do the same check a second time, and in fact this unnecessary check is
what caused the problem that Paul observed.
Note that performing the unnecessary check is not actually a bug.
Devices are supposed to be able to send descriptors back to the host
even when they are busy doing something else. The underlying cause of
Paul's problem lies in his Bluetooth adapter. Nevertheless, we
shouldn't perform the same check twice in a row -- and as a nice side
benefit, removing the extra check allows the Bluetooth adapter to work
more reliably.
The work thread performs its check when it sees that the port's bit is
set in hub->change_bits. In this situation that bit is interpreted as
though a connect-change event had occurred on the port _after_ the
reset-resume, which is not what actually happened.
One possible fix would be to make the reset-resume code clear the
port's bit in hub->change_bits. But it seems simpler to just avoid
setting the bit during hub_activate() in the first place. That's what
this patch does.
(Proving that the patch is correct when CONFIG_PM is disabled requires
a little thought. In that setting hub_activate() will be called only
for initialization and resets, since there won't be any resumes or
reset-resumes. During initialization and hub resets the hub doesn't
have any child devices, and so this code path never gets executed.)
Reported-and-tested-by: Paul Zimmerman <pauldzim@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://marc.info/?t=157949360700001&r=1&w=2
CC: David Heinzelmann <heinzelmann.david@gmail.com>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2001311037460.1577-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a uas disk is plugged into an external hub, uas_probe()
will be called by the hub thread to do the probe. It will
first create a SCSI host and then do the scan for this host.
During the scan, it will probe the LUN using SCSI INQUERY command
which will be packed in the URB and submitted to uas disk.
There might be a chance that this external hub with uas disk
attached is unplugged during the scan. In this case, uas driver
will fail to submit the URB (due to the NOTATTACHED state of uas
device) and try to put this SCSI command back to request queue
waiting for next chance to run.
In normal case, this cycle will terminate when hub thread gets
disconnection event and calls into uas_disconnect() accordingly.
But in this case, uas_disconnect() will not be called because
hub thread of external hub gets stuck waiting for the completion
of this SCSI command. A deadlock happened.
In this fix, uas will call scsi_scan_host() asynchronously to
avoid the blocking of hub thread.
Signed-off-by: EJ Hsu <ejh@nvidia.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200130092506.102760-1-ejh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Renesas R-Car H3ULCB + Kingfisher Infotainment Board is either not able
to detect the USB3.0 mass storage devices or is detecting those as
USB2.0 high speed devices.
The explanation given by Renesas is that, due to a HW issue, the XHCI
driver does not wake up after going to sleep on connecting a USB3.0
device.
In order to mitigate that, disable the auto-suspend feature
specifically for SMSC hubs from hub_probe() function, as a quirk.
Renesas Kingfisher Infotainment Board has two USB3.0 ports (CN2) which
are connected via USB5534B 4-port SuperSpeed/Hi-Speed, low-power,
configurable hub controller.
[1] SanDisk USB 3.0 device detected as USB-2.0 before the patch
[ 74.036390] usb 5-1.1: new high-speed USB device number 4 using xhci-hcd
[ 74.061598] usb 5-1.1: New USB device found, idVendor=0781, idProduct=5581, bcdDevice= 1.00
[ 74.069976] usb 5-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 74.077303] usb 5-1.1: Product: Ultra
[ 74.080980] usb 5-1.1: Manufacturer: SanDisk
[ 74.085263] usb 5-1.1: SerialNumber: 4C530001110208116550
[2] SanDisk USB 3.0 device detected as USB-3.0 after the patch
[ 34.565078] usb 6-1.1: new SuperSpeed Gen 1 USB device number 3 using xhci-hcd
[ 34.588719] usb 6-1.1: New USB device found, idVendor=0781, idProduct=5581, bcdDevice= 1.00
[ 34.597098] usb 6-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 34.604430] usb 6-1.1: Product: Ultra
[ 34.608110] usb 6-1.1: Manufacturer: SanDisk
[ 34.612397] usb 6-1.1: SerialNumber: 4C530001110208116550
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Hardik Gajjar <hgajjar@de.adit-jv.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1580989763-32291-1-git-send-email-hgajjar@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel hosts that need the XHCI_PME_STUCK_QUIRK flag should enable
runtime pm by calling xhci_pme_acpi_rtd3_enable() before
usb_hcd_pci_probe() calls pci_dev_run_wake().
Otherwise usage count for the device won't be decreased, and runtime
suspend is prevented.
usb_hcd_pci_probe() only decreases the usage count if device can
generate run-time wake-up events, i.e. when pci_dev_run_wake()
returns true.
This issue was exposed by pci_dev_run_wake() change in
commit 8feaec33b9 ("PCI / PM: Always check PME wakeup capability for
runtime wakeup support")
and should be backported to kernels with that change
Cc: <stable@vger.kernel.org> # 4.13+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200210134553.9144-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci driver assumed that xHC controllers have at most one custom
supported speed table (PSI) for all usb 3.x ports.
Memory was allocated for one PSI table under the xhci hub structure.
Turns out this is not the case, some controllers have a separate
"supported protocol capability" entry with a PSI table for each port.
This means each usb3 roothub port can in theory support different custom
speeds.
To solve this, cache all supported protocol capabilities with their PSI
tables in an array, and add pointers to the xhci port structure so that
every port points to its capability entry in the array.
When creating the SuperSpeedPlus USB Device Capability BOS descriptor
for the xhci USB 3.1 roothub we for now will use only data from the
first USB 3.1 capable protocol capability entry in the array.
This could be improved later, this patch focuses resolving
the memory leak.
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reported-by: Sajja Venkateswara Rao <VenkateswaraRao.Sajja@amd.com>
Fixes: 47189098f8 ("xhci: parse xhci protocol speed ID list for usb 3.1 usage")
Cc: stable <stable@vger.kernel.org> # v4.4+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200210134553.9144-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A Full-speed bulk USB audio device (DJ-Tech CTRL) with a invalid Maximum
Packet Size of 4 causes a xHC "Parameter Error" at enumeration.
This is because valid Maximum packet sizes for Full-speed bulk endpoints
are 8, 16, 32 and 64 bytes. Hosts are not required to support other values
than these. See usb 2 specs section 5.8.3 for details.
The device starts working after forcing the maximum packet size to 8.
This is most likely the case with other devices as well, so force the
maximum packet size to a valid range.
Cc: stable@vger.kernel.org
Reported-by: Rene D Obermueller <cmdrrdo@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200210134553.9144-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pointer priv is being assigned with a value that is never read, it is
assigned a new value later on in a for-loop. The assignment is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Commit a8d78d9f38 ("USB: serial: clean up throttle handling")
converted the throttle handling to use atomic bitops. This means that we
can relax the smp_mb() in unthrottle() to smp_mb__after_atomic(), which
for example is a no-op on architectures like x86 that provide fully
ordered atomics.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
While assumed not to make a difference, not using the factor-2 prescaler
makes the receiver more susceptible to errors.
Specifically, there have been reports of problems with devices that
cannot generate a 115200 rate with a smaller error than 2.1% (e.g.
117647 bps). But this can also be reproduced with a low-speed RS232
tranceiver at 115200 when the input rate matches the nominal rate.
So whenever possible, enable the factor-2 prescaler and halve the
divisor in order to use settings closer to that of the previous
algorithm.
Fixes: 3571456508 ("USB: serial: ch341: reimplement line-speed handling")
Cc: stable <stable@vger.kernel.org> # 5.5
Reported-by: Jakub Nantl <jn@forever.cz>
Tested-by: Jakub Nantl <jn@forever.cz>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The "actual_length" variable might be uninitialized on some failure
paths. It's harmless but static analysis tools like Smatch complain
and at runtime the UBSan tool will likely complain as well.
Fixes: e7542bc382 ("USB: serial: ir-usb: make set_termios synchronous")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Pull vfs file system parameter updates from Al Viro:
"Saner fs_parser.c guts and data structures. The system-wide registry
of syntax types (string/enum/int32/oct32/.../etc.) is gone and so is
the horror switch() in fs_parse() that would have to grow another case
every time something got added to that system-wide registry.
New syntax types can be added by filesystems easily now, and their
namespace is that of functions - not of system-wide enum members. IOW,
they can be shared or kept private and if some turn out to be widely
useful, we can make them common library helpers, etc., without having
to do anything whatsoever to fs_parse() itself.
And we already get that kind of requests - the thing that finally
pushed me into doing that was "oh, and let's add one for timeouts -
things like 15s or 2h". If some filesystem really wants that, let them
do it. Without somebody having to play gatekeeper for the variants
blessed by direct support in fs_parse(), TYVM.
Quite a bit of boilerplate is gone. And IMO the data structures make a
lot more sense now. -200LoC, while we are at it"
* 'merge.nfs-fs_parse.1' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (25 commits)
tmpfs: switch to use of invalfc()
cgroup1: switch to use of errorfc() et.al.
procfs: switch to use of invalfc()
hugetlbfs: switch to use of invalfc()
cramfs: switch to use of errofc() et.al.
gfs2: switch to use of errorfc() et.al.
fuse: switch to use errorfc() et.al.
ceph: use errorfc() and friends instead of spelling the prefix out
prefix-handling analogues of errorf() and friends
turn fs_param_is_... into functions
fs_parse: handle optional arguments sanely
fs_parse: fold fs_parameter_desc/fs_parameter_spec
fs_parser: remove fs_parameter_description name field
add prefix to fs_context->log
ceph_parse_param(), ceph_parse_mon_ips(): switch to passing fc_log
new primitive: __fs_parse()
switch rbd and libceph to p_log-based primitives
struct p_log, variants of warnf() et.al. taking that one instead
teach logfc() to handle prefices, give it saner calling conventions
get rid of cg_invalf()
...
Unused now.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Here is the big USB and Thunderbolt and PHY driver updates for 5.6-rc1.
With the advent of USB4, "Thunderbolt" has really become USB4, so the
renaming of the Kconfig option and starting to share subsystem code has
begun, hence both subsystems coming in through the same tree here.
PHY driver updates also touched USB drivers, so that is coming in
through here as well.
Major stuff included in here are:
- USB 4 initial support added (i.e. Thunderbolt)
- musb driver updates
- USB gadget driver updates
- PHY driver updates
- USB PHY driver updates
- lots of USB serial stuff fixed up
- USB typec updates
- USB-IP fixes
- lots of other smaller USB driver updates
All of these have been in linux-next for a while now (the usb-serial
tree is already tested in linux-next on its own before merged into
here), with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXjFTNw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynpKQCgrh2FoobS2x0oFg/OUHdjokQV/BYAoJGWLOmt
8S5cnsCuLq3w5qpCcBva
=PMGd
-----END PGP SIGNATURE-----
Merge tag 'usb-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/Thunderbolt/PHY driver updates from Greg KH:
"Here is the big USB and Thunderbolt and PHY driver updates for
5.6-rc1.
With the advent of USB4, "Thunderbolt" has really become USB4, so the
renaming of the Kconfig option and starting to share subsystem code
has begun, hence both subsystems coming in through the same tree here.
PHY driver updates also touched USB drivers, so that is coming in
through here as well.
Major stuff included in here are:
- USB 4 initial support added (i.e. Thunderbolt)
- musb driver updates
- USB gadget driver updates
- PHY driver updates
- USB PHY driver updates
- lots of USB serial stuff fixed up
- USB typec updates
- USB-IP fixes
- lots of other smaller USB driver updates
All of these have been in linux-next for a while now (the usb-serial
tree is already tested in linux-next on its own before merged into
here), with no reported issues"
[ Removed an incorrect compile test enablement for PHY_EXYNOS5250_SATA
that causes configuration warnings - Linus ]
* tag 'usb-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (207 commits)
Doc: ABI: add usb charger uevent
usb: phy: show USB charger type for user
usb: cdns3: fix spelling mistake and rework grammar in text
usb: phy: phy-gpio-vbus-usb: Convert to GPIO descriptors
USB: serial: cyberjack: fix spelling mistake "To" -> "Too"
USB: serial: ir-usb: simplify endpoint check
USB: serial: ir-usb: make set_termios synchronous
USB: serial: ir-usb: fix IrLAP framing
USB: serial: ir-usb: fix link-speed handling
USB: serial: ir-usb: add missing endpoint sanity check
usb: typec: fusb302: fix "op-sink-microwatt" default that was in mW
usb: typec: wcove: fix "op-sink-microwatt" default that was in mW
usb: dwc3: pci: add ID for the Intel Comet Lake -V variant
usb: typec: tcpci: mask event interrupts when remove driver
usb: host: xhci-tegra: set MODULE_FIRMWARE for tegra186
usb: chipidea: add inline for ci_hdrc_host_driver_init if host is not defined
usb: chipidea: handle single role for usb role class
usb: musb: fix spelling mistake: "periperal" -> "peripheral"
phy: ti: j721e-wiz: Fix build error without CONFIG_OF_ADDRESS
USB: usbfs: Always unlink URBs in reverse order
...
- remove ioremap_nocache given that is is equivalent to
ioremap everywhere
-----BEGIN PGP SIGNATURE-----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=TUCJ
-----END PGP SIGNATURE-----
Merge tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap
Pull ioremap updates from Christoph Hellwig:
"Remove the ioremap_nocache API (plus wrappers) that are always
identical to ioremap"
* tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap:
remove ioremap_nocache and devm_ioremap_nocache
MIPS: define ioremap_nocache to ioremap
Add support for reference properties in sofrware nodes (Dmitry
Torokhov) and a basic test for property entries along with fixes
on top of it (Dmitry Torokhov, Qian Cai, Alan Maguire).
-----BEGIN PGP SIGNATURE-----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=wnoj
-----END PGP SIGNATURE-----
Merge tag 'devprop-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull device properties framework updates from Rafael Wysocki:
"Add support for reference properties in sofrware nodes (Dmitry
Torokhov) and a basic test for property entries along with fixes on
top of it (Dmitry Torokhov, Qian Cai, Alan Maguire)"
* tag 'devprop-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
software node: introduce CONFIG_KUNIT_DRIVER_PE_TEST
usb: dwc3: use proper initializers for property entries
drivers/base/test: fix global-out-of-bounds error
software node: add basic tests for property entries
software node: remove separate handling of references
platform/x86: intel_cht_int33fe: use inline reference properties
software node: implement reference properties
software node: allow embedding of small arrays into property_entry
software node: replace is_array with is_inline
- a missing ir-usb endpoint sanity check
- fixes for two long-standing regressions in ir-usb
- opticon chars_in_buffer support
Included are also various clean ups.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXi6evgAKCRALxc3C7H1l
CJs8AP4ubaKYyH5cLMthwhLAdGqp2UdfVqdUu25Kb2bnyXbStAEAsvhOHWbdrQKn
cRLLJqYO4M3nPH2YF1Is4qSJZmUxXQk=
=Aof1
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.6-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
Here are the USB-serial updates for 5.6-rc1, including:
- a missing ir-usb endpoint sanity check
- fixes for two long-standing regressions in ir-usb
- opticon chars_in_buffer support
Included are also various clean ups.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-5.6-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: cyberjack: fix spelling mistake "To" -> "Too"
USB: serial: ir-usb: simplify endpoint check
USB: serial: ir-usb: make set_termios synchronous
USB: serial: ir-usb: fix IrLAP framing
USB: serial: ir-usb: fix link-speed handling
USB: serial: ir-usb: add missing endpoint sanity check
USB: serial: garmin_gps: Use flexible-array member
USB: serial: opticon: stop all I/O on close()
USB: serial: opticon: add chars_in_buffer() implementation
Current USB charger framework only shows charger state for user, but the
user may also need charger type for further use, add support for it.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/1579145333-1657-1-git-send-email-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The text contains a spelling mistake, "to" should be "too"
so fix this and re-work the grammar to make it more readable.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/20200122234437.2829803-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of using the legacy GPIO API and keeping track on
polarity inversion semantics in the driver, switch to use
GPIO descriptors for this driver and change all consumers
in the process.
This makes it possible to retire platform data completely:
the only remaining platform data member was "wakeup" which
was intended to make the vbus interrupt wakeup capable,
but was not set by any users and thus remained unused. VBUS
was not waking any devices up. Leave a comment about it so
later developers using the platform can consider setting it
to always enabled so plugging in USB wakes up the platform.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Felipe Balbi <balbi@kernel.org>
Acked-by: Sylwester Nawrocki <snawrocki@kernel.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200123155013.93249-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a spelling mistake in a dev_dbg message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Simplify the endpoint sanity check by letting core verify that the
required endpoints are present.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Use a synchronous usb_bulk_msg() when switching link speed in
set_termios(). This way we do not need to keep track of outstanding URBs
in order to be able to stop them at close.
Note that there's no need to set URB_ZERO_PACKET as the one-byte
transfer will always be short.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Commit f4a4cbb204 ("USB: ir-usb: reimplement using generic framework")
switched to using the generic write implementation which may combine
multiple write requests into larger transfers. This can break the IrLAP
protocol where end-of-frame is determined using the USB short packet
mechanism, for example, if multiple frames are sent in rapid succession.
Fixes: f4a4cbb204 ("USB: ir-usb: reimplement using generic framework")
Cc: stable <stable@vger.kernel.org> # 2.6.35
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Commit e0d795e4f3 ("usb: irda: cleanup on ir-usb module") added a USB
IrDA header with common defines, but mistakingly switched to using the
class-descriptor baud-rate bitmask values for the outbound header.
This broke link-speed handling for rates above 9600 baud, but a device
would also be able to operate at the default 9600 baud until a
link-speed request was issued (e.g. using the TCGETS ioctl).
Fixes: e0d795e4f3 ("usb: irda: cleanup on ir-usb module")
Cc: stable <stable@vger.kernel.org> # 2.6.27
Cc: Felipe Balbi <balbi@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add missing endpoint sanity check to avoid dereferencing a NULL-pointer
on open() in case a device lacks a bulk-out endpoint.
Note that prior to commit f4a4cbb204 ("USB: ir-usb: reimplement using
generic framework") the oops would instead happen on open() if the
device lacked a bulk-in endpoint and on write() if it lacked a bulk-out
endpoint.
Fixes: f4a4cbb204 ("USB: ir-usb: reimplement using generic framework")
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
commit 8f6244055b ("usb: typec: fusb302: Always provide fwnode for the
port") didn't convert this value from mW to uW when migrating to a new
specification format like it should have.
Fixes: 8f6244055b ("usb: typec: fusb302: Always provide fwnode for the port")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/0da564559af75ec829c6c7e3aa4024f857c91bee.1579529334.git.tommyhebb@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c912bff46 ("usb: typec: wcove: Provide fwnode for the port")
didn't convert this value from mW to uW when migrating to a new
specification format like it should have.
Fixes: 4c912bff46 ("usb: typec: wcove: Provide fwnode for the port")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/d8be32512efd31995ad7d65b27df9d443131b07c.1579529334.git.tommyhebb@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is one more Comet Lake PCH variant, CML-V, that has
its own PCI ID.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200117093033.48616-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is to prevent any possible events generated while unregister
tpcm port.
Fixes: 74e656d6b0 ("staging: typec: Type-C Port Controller Interface driver (tcpci)")
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1579502333-4145-1-git-send-email-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the MODULE_FIRMWARE for tegra186, it's registered for 124/210 and
ensures the firmware is available at the appropriate time such as in
the initrd, else if the firmware is unavailable the driver fails with
the following errors:
tegra-xusb 3530000.usb: Direct firmware load for nvidia/tegra186/xusb.bin failed with error -2
tegra-xusb 3530000.usb: failed to request firmware: -2
tegra-xusb 3530000.usb: failed to load firmware: -2
tegra-xusb: probe of 3530000.usb failed with error -2
Fixes: 5f9be5f3f8 ("usb: host: xhci-tegra: Add Tegra186 XUSB support")
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200120141910.116097-1-pbrobinson@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Otherwise, there is a build warning if this header file is included
by non host source file, eg, otg.c.
Signed-off-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200122014639.22667-3-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If usb port is configed to be single role, but usb role class
is trying to set unavailable role, don't try to do role change.
Signed-off-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200122014639.22667-2-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a spelling mistake in a dev_err error message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200117093124.97965-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are a few fixes for issues related to unbound port devices which
could lead to NULL-pointer dereferences. Notably the bind attributes for
usb-serial (port) drivers are removed as almost none of the drivers can
handle individual ports going away once they've been bound.
Included are also some new device ids.
All but the unbound-port fixes have been in linux-next with no reported
issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXiHp+QAKCRALxc3C7H1l
CL7LAP0ebAAIpNu29R+K+fXCq/rnbAjulmmlfZH/E8rFPuk1lAD+N+XMGtpbABYm
jO7G47KepbJsY+NkDu49xVoGtHDXUAk=
=oImC
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.5-rc7' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.5-rc7
Here are a few fixes for issues related to unbound port devices which
could lead to NULL-pointer dereferences. Notably the bind attributes for
usb-serial (port) drivers are removed as almost none of the drivers can
handle individual ports going away once they've been bound.
Included are also some new device ids.
All but the unbound-port fixes have been in linux-next with no reported
issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-5.5-rc7' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: quatech2: handle unbound ports
USB: serial: keyspan: handle unbound ports
USB: serial: io_edgeport: add missing active-port sanity check
USB: serial: io_edgeport: handle unbound ports on URB completion
USB: serial: ch341: handle unbound port at reset_resume
USB: serial: suppress driver bind attributes
USB: serial: option: add support for Quectel RM500Q in QDL mode
USB: serial: opticon: fix control-message timeouts
USB: serial: option: Add support for Quectel RM500Q
USB: serial: simple: Add Motorola Solutions TETRA MTP3xxx and MTP85xx
When the kernel unlinks a bunch of URBs for a single endpoint, it
should always unlink them in reverse order. This eliminates any
possibility that some URB x will be unlinked before it can execute but
the following URB x+1 will execute before it can be unlinked. Such an
event would be bad, for obvious reasons.
Chris Dickens pointed out that usbfs doesn't behave this way when it
is unbound from an interface. All pending URBs are cancelled, but in
the order of submission. This patch changes the behavior to make the
unlinks occur in reverse order. It similarly changes the behavior
when usbfs cancels the continuation URBs for a BULK endpoint.
Suggested-by: Chris Dickens <christopher.a.dickens@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2001171045380.1571-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check for NULL port data in the modem- and line-status handlers to avoid
dereferencing a NULL pointer in the unlikely case where a port device
isn't bound to a driver (e.g. after an allocation failure on port
probe).
Note that the other (stubbed) event handlers qt2_process_xmit_empty()
and qt2_process_flush() would need similar sanity checks in case they
are ever implemented.
Fixes: f7a33e608d ("USB: serial: add quatech2 usb to serial driver")
Cc: stable <stable@vger.kernel.org> # 3.5
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Check for NULL port data in the control URB completion handlers to avoid
dereferencing a NULL pointer in the unlikely case where a port device
isn't bound to a driver (e.g. after an allocation failure on port
probe()).
Fixes: 0ca1268e10 ("USB Serial Keyspan: add support for USA-49WG & USA-28XG")
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The driver receives the active port number from the device, but never
made sure that the port number was valid. This could lead to a
NULL-pointer dereference or memory corruption in case a device sends
data for an invalid port.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Check for NULL port data in the shared interrupt and bulk completion
callbacks to avoid dereferencing a NULL pointer in case a device sends
data for a port device which isn't bound to a driver (e.g. due to a
malicious device having unexpected endpoints or after an allocation
failure on port probe).
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Check for NULL port data in reset_resume() to avoid dereferencing a NULL
pointer in case the port device isn't bound to a driver (e.g. after a
failed control request at port probe).
Fixes: 1ded7ea47b ("USB: ch341 serial: fix port number changed after resume")
Cc: stable <stable@vger.kernel.org> # 2.6.30
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Old code in the kernel uses 1-byte and 0-byte arrays to indicate the
presence of a "variable length array":
struct something {
int length;
u8 data[1];
};
struct something *instance;
instance = kmalloc(sizeof(*instance) + size, GFP_KERNEL);
instance->length = size;
memcpy(instance->data, source, size);
There is also 0-byte arrays. Both cases pose confusion for things like
sizeof(), CONFIG_FORTIFY_SOURCE, etc.[1] Instead, the preferred mechanism
to declare variable-length types such as the one above is a flexible array
member[2] which need to be the last member of a structure and empty-sized:
struct something {
int stuff;
u8 data[];
};
Also, by making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
unadvertenly introduced[3] to the codebase from now on.
[1] https://github.com/KSPP/linux/issues/21
[2] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to stop any submitted write URBs on close().
Note that the tty layer will wait up to 30 seconds for the buffers to
drain before close() is called.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add a chars_in_buffer() implementation so that the tty layer will wait
for outgoing buffered data to be drained when needed (e.g. on final
close()).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
USB-serial drivers must not be unbound from their ports before the
corresponding USB driver is unbound from the parent interface so
suppress the bind and unbind attributes.
Unbinding a serial driver while it's port is open is a sure way to
trigger a crash as any driver state is released on unbind while port
hangup is handled on the parent USB interface level. Drivers for
multiport devices where ports share a resource such as an interrupt
endpoint also generally cannot handle individual ports going away.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
*) Add support in PHY core to create link between PHY consumer and PHY
provider
*) Add DisplayPort PHY configuration set to be used for negotiating the
configurations to be used between DisplayPort controller and
DisplayPort PHY
*) Add PHY wrapper driver (configure inputs to Cadence Sierra PHY) for
TI's J721E SoC and adapt Cadence Sierra PHY driver to be used for
J721E SoC (Supports USB and PCIe)
*) Add PHY driver for eMMC PHY in Intel LGM SoC
*) Add PHY support for 7216 and 7211 Broadcom SoCs which uses the new
Synopsys USB Controller
*) Add support for 16nm SATA PHY present in Broadcom 7216 SoC
*) Fix lost packet issue, fix MDIO from getting inaccessible, fix
occasional transaction failures, fix USB driver from crashing in
Broadcom USB PHY driver
*) Fix missing PCS SW reset in UFS PHY of Qualcomm SM8150
*) Use "struct phy_configure_opts_mipi_dphy" to pass parameters from
display controller to rockchip-inno-dsidphy
*) Other cleanups including compile testing for some of the PHY drivers,
fixing Kconfig indentation, duplicate writes in drivers etc.,
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----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=76zg
-----END PGP SIGNATURE-----
Merge tag 'phy-for-5.6_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 5.6
*) Add support in PHY core to create link between PHY consumer and PHY
provider
*) Add DisplayPort PHY configuration set to be used for negotiating the
configurations to be used between DisplayPort controller and
DisplayPort PHY
*) Add PHY wrapper driver (configure inputs to Cadence Sierra PHY) for
TI's J721E SoC and adapt Cadence Sierra PHY driver to be used for
J721E SoC (Supports USB and PCIe)
*) Add PHY driver for eMMC PHY in Intel LGM SoC
*) Add PHY support for 7216 and 7211 Broadcom SoCs which uses the new
Synopsys USB Controller
*) Add support for 16nm SATA PHY present in Broadcom 7216 SoC
*) Fix lost packet issue, fix MDIO from getting inaccessible, fix
occasional transaction failures, fix USB driver from crashing in
Broadcom USB PHY driver
*) Fix missing PCS SW reset in UFS PHY of Qualcomm SM8150
*) Use "struct phy_configure_opts_mipi_dphy" to pass parameters from
display controller to rockchip-inno-dsidphy
*) Other cleanups including compile testing for some of the PHY drivers,
fixing Kconfig indentation, duplicate writes in drivers etc.,
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-5.6_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy: (54 commits)
dt-bindings: phy: Add PHY_TYPE_DP definition
phy: ti: j721e-wiz: Fix return value check in wiz_probe()
dt-bindings: usb: Convert Allwinner A80 USB PHY controller to a schema
phy: intel-lgm-emmc: Fix warning by adding missing MODULE_LICENSE
phy: ti: j721e-wiz: Manage typec-gpio-dir
dt-bindings: phy: ti,phy-j721e-wiz: Add Type-C dir GPIO
phy: cadence: Sierra: add phy_reset hook
phy: cadence: Sierra: remove redundant initialization of pointer regmap
phy: Add DisplayPort configuration options
phy: Enable compile testing for some of drivers
phy: mediatek: Fix Kconfig indentation
phy: intel-lgm-emmc: Add support for eMMC PHY
dt-bindings: phy: intel-emmc-phy: Add YAML schema for LGM eMMC PHY
phy: ti: j721e-wiz: Add support for WIZ module present in TI J721E SoC
dt-bindings: phy: Document WIZ (SERDES wrapper) bindings
phy: cadence: Sierra: Use correct dev pointer in cdns_sierra_phy_remove()
phy: cadence: Sierra: Set cmn_refclk_dig_div/cmn_refclk1_dig_div frequency to 25MHz
phy: cadence: Sierra: Change MAX_LANES of Sierra to 16
phy: cadence: Sierra: Check for PLL lock during PHY power on
phy: cadence: Sierra: Get reset control "array" for each link
...
Since commit 0782e8572c ("ARM: dts: Probe am335x musb with ti-sysc"),
the dummy driver musb_am335x.c is no longer needed, let's drop it.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200115132547.364-26-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DaVinci MUSB glue contains an optional GPIO line to
control VBUS power, convert this to use a GPIO descriptor
and augment the EVM board file to provide this descriptor.
I can't get this driver to compile properly and it depends
on broken but when I didn get it to compile brokenly, it
did at least not complain about THIS code being broken so
I don't think I broke the driver any more than what it
already is.
I did away with the ifdefs that do not work with
multiplatform anyway so the day someone decides to
resurrect the code, the path to get it working should be
easier as well since DaVinci is now multiplatform.
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[b-liu@ti.com: fixed one instance still ref to global variable vbus_state]
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200115132547.364-25-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds support for MediaTek musb controller in
host, peripheral and otg mode.
There are some quirk of MediaTek musb controller, such as:
-W1C interrupt status registers
-Private data toggle registers
-No dedicated DMA interrupt line
Signed-off-by: Min Guo <min.guo@mediatek.com>
Signed-off-by: Yonglong Wu <yonglong.wu@mediatek.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200115132547.364-24-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Delete the const attribute of addr parameter in readb/w/l hooks, these
changes are for implementing clearing W1C registers.
Replace musb_readb/w with musb_clearb/w to clear the interrupt status.
While at here, change some unsigned type to u32 to fix checkpatch.pl
warnings.
Signed-off-by: Min Guo <min.guo@mediatek.com>
[b-liu@ti.com: fix checkpatch.pl warnings.]
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200115132547.364-23-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add noirq type of dma create interface for platform which do not
have dedicated DMA interrupt line, move musbhsdma macro definition
to musb_dma.h
Signed-off-by: Min Guo <min.guo@mediatek.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200115132547.364-22-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add get/set toggle hooks in struct musb_io and struct musb_platform_ops
for special platform; remove function musb_save_toggle, use the set/get
callback to handle toggle.
Signed-off-by: Min Guo <min.guo@mediatek.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200115132547.364-21-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200115132547.364-19-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix lines with too much or not enough indentation, and lines which were
indented with spaces instead of tabs.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200115132547.364-17-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a /* sentinel */ comment to the sentinel entry of the devicetree ID
table, and fix a multi-line comment not having its opening token on a
separate line.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200115132547.364-16-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Name the platform_device pointer 'pdev' instead of 'musb'. Since the
driver also deal with pointers to 'struct musb', it can be very
confusing to have a pointer named after this struct but with a different
type.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200115132547.364-15-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By moving around the jz4740_musb_pdata structure, we can have the
.platform_ops field initialized, so that we don't have to initialize it
manually in the probe function. Therefore, the struct can be const now.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200115132547.364-14-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up the probe function by using a local 'struct device *dev'
variable, instead of referencing &pdev->dev everytime.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200115132547.364-13-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'dev' field was never read anywhere.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200115132547.364-12-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we've removed direct calls from interrupt handler to
omap2430_musb_set_vbus(), let's make things less confusing and
configure VBUS directly in omap_musb_set_mailbox().
We have omap_musb_set_mailbox() called from the PHYs, and that's
all we need.
Note that we can now also drop the check for MUSB_INTERFACE_UTMI,
we've been already calling otg_set_vbus(musb->xceiv->otg, 0)
unconditionally via omap2430_musb_set_vbus() and we should only
need to call it once.
And we want to disable VBUS unconditionally on disconnect even
without musb->gadget_driver, so let's drop that check too.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200115132547.364-11-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want to configure musb state in omap2430_musb_enable() instead of
omap2430_musb_init(). Otherwise musb may not idle properly until
USB cable has been connected at least once.
And we already have omap_musb_set_mailbox() configure mode with
omap_control_usb_set_mode() so we can remove those calls from
omap2430_musb_enable().
Cc: Jacopo Mondi <jacopo@jmondi.org>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200115132547.364-10-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There should be no need to tinker with devctl in enable in the SoC glue
code. We have musb_start() to take care of handling it already.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200115132547.364-9-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At least some revisions of musb core need to set devctl session bit
in peripheral mode to force musb to host mode. And we have places
clearing the devctl session bit.
Let's add a generic function to do this, and use it for omap2430.
This should get us a bit closer to completely removing devctl register
tinkering in the SoC glue code.
Before making use of this code for the other glue layers, things need
to be tested carefully as there may be a approximately a 200 ms delay
needed between powering up musb and calling musb_set_host() to avoid.
Otherwise the system hangs at least with omap2430 glue layer.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
[b-liu@ti.com: fixed "line over 80 characters" warning]
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200115132547.364-8-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We currently get "unhandled DISCONNECT transition" warnings from musb core
on device disconnect as things are wrongly set to OTG_STATE_A_IDLE in
host mode when enumerating devices. We can also get "Failed to write reg
index" errors after enumerating.
This is happening at least with cpcap phy where we get multiple ID ground
interrupts. Looks like it's VBUS keeps timing out and needs to be kicked
when the phy sends multiple ID ground interrupts during host mode.
Cc: Jacopo Mondi <jacopo@jmondi.org>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200115132547.364-7-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can get babble interrupt if we attempt to switch to USB host mode too
soon after enabling musb. Let's fix the issue by waiting a bit in
runtime_resume.
Cc: Jacopo Mondi <jacopo@jmondi.org>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200115132547.364-6-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We currently have musb_set_vbus() called from two different paths. Mostly
it gets called from the USB PHY via omap_musb_set_mailbox(), but in some
cases it can get also called from musb_stage0_irq() rather via .set_vbus:
(musb_set_host [musb_hdrc])
(omap2430_musb_set_vbus [omap2430])
(musb_stage0_irq [musb_hdrc])
(musb_interrupt [musb_hdrc])
(omap2430_musb_interrupt [omap2430])
This is racy and will not work with introducing generic helper functions
for musb_set_host() and musb_set_peripheral(). We want to get rid of the
busy loops in favor of usleep_range().
Let's just get rid of .set_vbus for omap2430 glue layer and let the PHY
code handle VBUS with musb_set_vbus(). Note that in the follow-up patch
we can completely remove omap2430_musb_set_vbus(), but let's do it in a
separate patch as this change may actually turn out to be needed as a
fix.
Reported-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200115132547.364-5-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver does not depend directly on the NOP transceiver. It can
compile and work just fine without it.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200115132547.364-4-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order for devicetree nodes to be correctly associated with attached
devices, the controller node needs to be propagated to the glue device.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200115132547.364-3-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update the function description of musb_stage0_irq() to remove unused
parameter.
Signed-off-by: Saurav Girepunje <saurav.girepunje@gmail.com>
[b-liu@ti.com: revised commit log]
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200115132547.364-2-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original dwc_otg driver used a DWC_WORKQ_SCHEDULE() wrapper to queue
work items. Because that wrapper acquired the driver's global spinlock,
an unlock/lock dance was necessary whenever a work item was queued up
while the global spinlock was already held.
The dwc2 driver dropped DWC_WORKQ_SCHEDULE() in favor of a direct call
to queue_work(), but retained the (now gratuitous) unlock/lock dance in
dwc2_handle_conn_id_status_change_intr(). Drop it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/77c07f00a6a9d94323c4a060a3c72817b0703b97.1574244795.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If hub_activate() is called before D+ has stabilized after remote
wakeup, the following situation might occur:
__ ___________________
/ \ /
D+ __/ \__/
Hub _______________________________
| ^ ^ ^
| | | |
Host _____v__|___|___________|______
| | | |
| | | \-- Interrupt Transfer (*3)
| | \-- ClearPortFeature (*2)
| \-- GetPortStatus (*1)
\-- Host detects remote wakeup
- D+ goes high, Host starts running by remote wakeup
- D+ is not stable, goes low
- Host requests GetPortStatus at (*1) and gets the following hub status:
- Current Connect Status bit is 0
- Connect Status Change bit is 1
- D+ stabilizes, goes high
- Host requests ClearPortFeature and thus Connect Status Change bit is
cleared at (*2)
- After waiting 100 ms, Host starts the Interrupt Transfer at (*3)
- Since the Connect Status Change bit is 0, Hub returns NAK.
In this case, port_event() is not called in hub_event() and Host cannot
recognize device. To solve this issue, flag change_bits even if only
Connect Status Change bit is 1 when got in the first GetPortStatus.
This issue occurs rarely because it only if D+ changes during a very
short time between GetPortStatus and ClearPortFeature. However, it is
fatal if it occurs in embedded system.
Signed-off-by: Keiya Nobuta <nobuta.keiya@fujitsu.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200109051448.28150-1-nobuta.keiya@fujitsu.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently ecm->notify_req is used to flag when a request is in-flight.
ecm->notify_req is set to NULL and when a request completes it is
subsequently reset.
This is fundamentally buggy in that the unbind logic of the ECM driver will
unconditionally free ecm->notify_req leading to a NULL pointer dereference.
Fixes: da741b8c56 ("usb ethernet gadget: split CDC Ethernet function")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently ncm->notify_req is used to flag when a request is in-flight.
ncm->notify_req is set to NULL and when a request completes it is
subsequently reset.
This is fundamentally buggy in that the unbind logic of the NCM driver will
unconditionally free ncm->notify_req leading to a NULL pointer dereference.
Fixes: 40d133d7f5 ("usb: gadget: f_ncm: convert to new function interface with backward compatibility")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We had a 100us delay to synchronize the END_TRANSFER command completion
before giving back requests to the function drivers. Now, the controller
driver can handle cancelled TRBs with the requests' cancelled_list and
it can also wait until the END_TRANSFER completion before starting new
transfers. Synchronization can simply base on the controller's command
completion interrupt. The 100us delay is no longer needed. Remove this
arbitrary delay.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the END_TRANSFER command hasn't completed yet, then don't send the
START_TRANSFER command. The controller may not be able to start if
that's the case. Some controller revisions depend on this. See
commit 76a638f8ac ("usb: dwc3: gadget: wait for End Transfer to
complete"). Let's only send START_TRANSFER command after the
END_TRANSFER command had completed.
Fixes: 3aec99154d ("usb: dwc3: gadget: remove DWC3_EP_END_TRANSFER_PENDING")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While the END_TRANSFER command is sent but not completed, any request
dequeue during this time will cause the driver to issue the END_TRANSFER
command. The driver needs to submit the command only once to stop the
controller from processing further. The controller may take more time to
process the same command multiple times unnecessarily. Let's add a flag
DWC3_EP_END_TRANSFER_PENDING to check for this condition.
Fixes: 3aec99154d ("usb: dwc3: gadget: remove DWC3_EP_END_TRANSFER_PENDING")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The packet size for USB audio must always be a multiple of the frame
size, otherwise we are transmitting a partial frame which omits some
channels (and these end up at the wrong offset in the next packet).
Furthermore, it breaks the residue handling such that we end up trying
to send a packet exceeding the maximum packet size for the endpoint.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a Cadence USB3 core for imx8qm and imx8qxp SoCs, the cdns
core is the child for this glue layer device.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
VBUS should be turned off when leaving the host mode.
Set GCTL_PRTCAP to device mode in teardown to de-assert DRVVBUS pin to
turn off VBUS power.
Fixes: 5f94adfeed ("usb: dwc3: core: refactor mode initialization to its own function")
Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch includes streams implementation changes.
The current changes has been validated on FPGA platform.
Enabled streams related interrupts only for streams capable endpoints.
Processed PRIME and IOT interrupts related to streams capable endpoints.
Based on PRIME interrupt prime_flag is set and transfer is armed
otherwise just adding request to the deferred request queue.
For streams capable endpoints preparing TD with correct stream ID.
TDL calculation:
Updated tdl calculation based on controller versions.
1. For controller version DEV_VER_V2 :We have enabled USB_CONF2_EN_TDL_TRB
bit in usb_conf2 register in DMULT configuration.
This enables TDL calculation based on TRB, hence setting TDL in TRB.
2. For controller Version < DEV_VER_V2 : Writing TDL and STDL in ep_cmd
register
3. For controller version > DEV_VER_V2 : Writing TDL in ep_tdl register.
Writing ERDY with correct Stream ID to ep_cmd register.
Added stream id related information to trace logs.
Signed-off-by: Rahul Kumar <kurahul@cadence.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Jayshri Pawar <jpawar@cadence.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver may sleep while holding a spinlock.
The function call path (from bottom to top) in Linux 4.19 is:
drivers/usb/gadget/udc/core.c, 1175:
kzalloc(GFP_KERNEL) in usb_add_gadget_udc_release
drivers/usb/gadget/udc/core.c, 1272:
usb_add_gadget_udc_release in usb_add_gadget_udc
drivers/usb/gadget/udc/gr_udc.c, 2186:
usb_add_gadget_udc in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2183:
spin_lock in gr_probe
drivers/usb/gadget/udc/core.c, 1195:
mutex_lock in usb_add_gadget_udc_release
drivers/usb/gadget/udc/core.c, 1272:
usb_add_gadget_udc_release in usb_add_gadget_udc
drivers/usb/gadget/udc/gr_udc.c, 2186:
usb_add_gadget_udc in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2183:
spin_lock in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 212:
debugfs_create_file in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2197:
gr_dfs_create in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2183:
spin_lock in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2114:
devm_request_threaded_irq in gr_request_irq
drivers/usb/gadget/udc/gr_udc.c, 2202:
gr_request_irq in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2183:
spin_lock in gr_probe
kzalloc(GFP_KERNEL), mutex_lock(), debugfs_create_file() and
devm_request_threaded_irq() can sleep at runtime.
To fix these possible bugs, usb_add_gadget_udc(), gr_dfs_create() and
gr_request_irq() are called without handling the spinlock.
These bugs are found by a static analysis tool STCheck written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UDC core uses req->num_sgs to judge if scatter buffer list is used.
Eg: usb_gadget_map_request_by_dev. For f_fs sync io mode, the request
is re-used for each request, so if the 1st request->length > PAGE_SIZE,
and the 2nd request->length is <= PAGE_SIZE, the f_fs uses the 1st
req->num_sgs for the 2nd request, it causes the UDC core get the wrong
req->num_sgs value (The 2nd request doesn't use sg). For f_fs async
io mode, it is not harm to initialize req->num_sgs as 0 either, in case,
the UDC driver doesn't zeroed request structure.
Cc: Jun Li <jun.li@nxp.com>
Cc: stable <stable@vger.kernel.org>
Fixes: 772a7a724f ("usb: gadget: f_fs: Allow scatter-gather buffers")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some functions support speeds other than SuperSpeed. Add max_speed
attribute to configfs gadget allowing user to specify the maximum speed
the composite driver supports. The valid input speed names are
super-speed-plus, super-speed, high-speed, full-speed, and low-speed.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we do not warn here, the user may not know failed to
find udc device by a gadget driver with the same name
because it silently fails. Let's print a warning in that
case so developers find these problems faster.
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These interfaces do support super-speed so let's not
limit maximum speed to high-speed.
Cc: <stable@vger.kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The number of FIFOs may be lower than the number of endpoints. Use the
correct total when printing FIFO details in debugfs.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The last user of the phy generic platform data was
deleted in commit 1e041b6f31
("usb: dwc3: exynos: Remove dead code"). So get rid of
the platform data, which rids us of another consumer of
the legacy GPIO API at the same time. Make sure we
only inlcude <linux/gpio/consumer.h> which is all we use.
Alter the usb_phy_gen_create_phy() function prototype to
not pass any platform data as this is just hardcoded to
NULL at all locations calling it in the kernel.
Move the devm_gpiod_get* calls out of the if (of_node)
parenthesis, as these calls are generic and do not depend
on device tree, they are used by any hardware description.
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a usb device disconnects in a certain way, dwc2_queue_transaction
still gets called after dwc2_hcd_cleanup_channels.
dwc2_hcd_cleanup_channels does "channel->qh = NULL;" but
dwc2_queue_transaction still wants to dereference qh.
This adds a check for a null qh.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
[dianders: rebased to mainline]
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stalling a Non-Isochronous OUT Endpoint flow changed according
programming guide.
In dwc2_hsotg_ep_sethalt() function for OUT EP should not be set STALL bit.
Instead should set SGOUTNAK in DCTL register. Set STALL bit should be
set only after GOUTNAKEFF interrupt asserted.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Send a no-action link state change request before the actual request
so DWC3 can send the same request whenever we call
dwc3_gadget_set_link_state().
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When DWC3 receives disconnect event, it needs to set the link state to
RX_Detect.
DWC_usb3 3.30a programming guide 4.1.7
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DCTL.ULSTCHNGREQ is a write-only field. When doing a read-modify-write
to DCTL, the driver must make sure that there's no unintended link state
change request from whatever is read from DCTL.ULSTCHNGREQ. Set link
state change to no-action when the driver writes to DCTL.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver was issuing synchronous uninterruptible control requests
without using a timeout. This could lead to the driver hanging
on open() or tiocmset() due to a malfunctioning (or malicious) device
until the device is physically disconnected.
The USB upper limit of five seconds per request should be more than
enough.
Fixes: 309a057932 ("USB: opticon: add rts and cts support")
Cc: stable <stable@vger.kernel.org> # 2.6.39
Cc: Martin Jansen <martin.jansen@opticon.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
There are few stale fields in tegra_ehci_hcd structure, let's remove them.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200106013416.9604-21-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to use usb_phy_set_suspend during of driver's probe
because now PHY driver enables hardware during of PHY's initialization.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200106013416.9604-20-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tegra's USB PHY driver now provides generic PHY init/shutdown callbacks
and thus the custom PHY management could be removed from Tegra-specific
part of the ChipIdea driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106013416.9604-18-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no good reason for disabling of CPU interrupts in order to
protect the utmip_pad_count modification.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106013416.9604-17-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's unlikely that two drivers could manage PHY's state simultaneously in
practice, nevertheless the utmip_pad_count checking should be under lock,
for consistency.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106013416.9604-16-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is much more intuitive if reset is treated as asserted when GPIO value
is set to 1. All NVIDIA Tegra device-trees are properly specifying active
state of the reset-GPIO since 2013, let's clean up that part of the code.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106013416.9604-14-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a mix of u32/ULONG usage in the driver's code. Let's switch to
u32 uniformly, for consistency.
Suggested-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106013416.9604-13-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The resource-managed variant removes the necessity for the driver to care
about freeing ULPI resources.
Suggested-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106013416.9604-12-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now drivers (like NVIDIA Tegra USB PHY for example) will be able to
benefit from the resource-managed variant, making driver's code a bit
cleaner.
Suggested-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106013416.9604-11-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is nothing to synchronize in regards to memory stores, thus all
readl/writel occurrences in the code could be replaced with a relaxed
versions, for consistency.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106013416.9604-9-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add "spinlock.h", which was included indirectly, and sort includes in
alphabet order.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106013416.9604-8-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes few dozens of legit checkpatch warnings, adds missed
handling of potential error-cases and prettifies code where makes sense.
All these clean-up changes are quite minor and do not fix any real
problems.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106013416.9604-7-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Generic PHY provides init/shutdown callbacks which allow USB-host drivers
to abstract PHY's hardware management in a common way. This change allows
to remove Tegra-specific PHY handling from the ChipIdea driver.
Note that ChipIdea's driver shall be changed at the same time because it
turns PHY ON without the PHY's initialization and this doesn't work now,
resulting in a NULL dereference of phy->freq because it's set during of
the PHY's initialization.
Acked-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106013416.9604-6-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PHY driver should keep track of the enable state, otherwise enable
refcount is screwed if USB driver tries to enable PHY when it is already
enabled. This will be the case for ChipIdea and Tegra EHCI drivers once
PHY driver will gain support for the init/shutdown callbacks.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106013416.9604-5-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Firstly, the PHY's clock needs to unprepared to keep prepare count
balanced. Secondly, downstream code suggests that reset is synchronous
and thus it should be asserted before disabling clock.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106013416.9604-4-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I found that PHY's enable refcounting was broken and after fixing it
I also found that machine started to hang after EHCI driver module
removal. Turned out that the teardown order is incorrect because HCD must
be unregistered *before* PHY's disabling. Note that it is also not correct
to assert the shared reset during of driver's removal because PHY takes
care of resetting shared pads and thus it's better to remove that part
from the EHCI driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200106013416.9604-3-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix up inconsistent usage of upper and lowercase letters in "Samsung"
and "Exynos" names.
"SAMSUNG" and "EXYNOS" are not abbreviations but regular trademarked
names. Therefore they should be written with lowercase letters starting
with capital letter.
The lowercase "Exynos" name is promoted by its manufacturer Samsung
Electronics Co., Ltd., in advertisement materials and on website.
Although advertisement materials usually use uppercase "SAMSUNG", the
lowercase version is used in all legal aspects (e.g. on Wikipedia and in
privacy/legal statements on
https://www.samsung.com/semiconductor/privacy-global/).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200104152107.11407-9-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Passing all the details that the alternate mode drivers
provide to the mux drivers during mode changes.
The mux drivers will in practice need to be able to make
decisions on their own. It is not enough that they get only
the requested port state. With the Thunderbolt 3 alternate
mode for example the mux driver will need to consider also
the capabilities of the cable before configuring the mux.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20191230142611.24921-13-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thunderbolt 3, and probable USB4 too, will need to be able
to get details about the cables. Adding typec_cable_get()
function that the alternate mode drivers can use to gain
access to gain access to the cable.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20191230142611.24921-4-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Originally the port drivers were expected to check does the
connector have the mode enabled or disabled when the alt
mode drivers attempted to enter the mode, but since
typec_altmode_enter() puts the connector into USB Safe
State before calling the port driver, it really has to do
the check on its own, and before changing the state.
Otherwise the connector may be left in USB Safe State if the
port driver does not move it back to normal USB operation
when the mode is disabled.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20191230142611.24921-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should not be reaching into property entries and initialize them by
hand, but rather use proper initializer macros. This way we can alter
internal representation of property entries with no visible changes to
their users.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is a spelling mistake in a dev_dbg message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200106111124.28100-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use resource_size rather than a verbose computation on
the end and start fields.
The semantic patch that makes these changes is as follows:
(http://coccinelle.lip6.fr/)
<smpl>
@@ struct resource ptr; @@
- (ptr.end - ptr.start + 1)
+ resource_size(&ptr)
</smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/1577900990-8588-2-git-send-email-Julia.Lawall@inria.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usba_gadget_template structure is only copied into another
structure, so make it const.
The opportunity for this change was found using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Acked-by: Cristian Birsan <cristian.birsan@microchip.com>
Link: https://lore.kernel.org/r/1577864614-5543-5-git-send-email-Julia.Lawall@inria.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to bd0e6c9614 ("usb: hub: try old enumeration scheme first
for high speed devices") the kernel will try the old enumeration scheme
first for high speed devices. This can happen when a high speed device
is plugged in.
But due to missing parentheses in the USE_NEW_SCHEME define, this logic
can get messed up and the incorrect result happens.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Qi Zhou <atmgnd@outlook.com>
Link: https://lore.kernel.org/r/ht4mtag8ZP-HKEhD0KkJhcFnVlOFV8N8eNjJVRD9pDkkLUNhmEo8_cL_sl7xy9mdajdH-T8J3TFQsjvoYQT61NFjQXy469Ed_BbBw_x4S1E=@protonmail.com
[ fixup changelog text - gregkh]
Cc: stable <stable@vger.kernel.org>
Fixes: bd0e6c9614 ("usb: hub: try old enumeration scheme first for high speed devices")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently when an error occurs when calling devm_gpiod_get_optional or
calling gpiod_to_irq it causes an uninitialized error return in variable
'error' to be returned. Fix this by ensuring the error variable is set
from da8xx_ohci->oc_gpio and oc_irq.
Thanks to Dan Carpenter for spotting the uninitialized error in the
gpiod_to_irq failure case.
Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: d193abf1c9 ("usb: ohci-da8xx: add vbus and overcurrent gpios")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200107123901.101190-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pullup may be already enabled before the driver is initialized. This
happens for instance on JZ4740.
It has to be disabled at init time, as we cannot guarantee that a gadget
driver will be bound to the UDC.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Suggested-by: Bin Liu <b-liu@ti.com>
Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200107152625.857-3-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When disconnected as USB B-device, suspend interrupt should come before
diconnect interrupt, because the DP/DM pins are shorter than the
VBUS/GND pins on the USB connectors. But we sometimes get a suspend
interrupt after disconnect interrupt. In that case we have devctl set to
99 with VBUS still valid and musb_pm_runtime_check_session() wrongly
thinks we have an active session. We have no other interrupts after
disconnect coming in this case at least with the omap2430 glue.
Let's fix the issue by checking the interrupt status again with
delayed work for the devctl 99 case. In the suspend after disconnect
case the devctl session bit has cleared by then and musb can idle.
For a typical USB B-device connect case we just continue with normal
interrupts.
Fixes: 467d5c9807 ("usb: musb: Implement session bit based runtime PM for musb-core")
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200107152625.857-2-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bit offsets for the Set Notification Enable command were
not considering the reserved bits in the middle.
Fixes: 470ce43a1a ("usb: typec: ucsi: Remove struct ucsi_control")
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200108131347.43217-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gcc -O3 warns about correct code:
inlined from 'oxu_hub_control.constprop' at drivers/usb/host/oxu210hp-hcd.c:3652:3:
include/linux/string.h:411:9: error: argument 1 null where non-null expected [-Werror=nonnull]
return __builtin_memset(p, c, size);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/usb/host/oxu210hp-hcd.c: In function 'oxu_hub_control.constprop':
include/linux/string.h:411:9: note: in a call to built-in function '__builtin_memset'
Expand the code slightly to let gcc better understand it and
not warn any more.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20200107214354.1008937-1-arnd@arndb.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The notification mask was not updated properly before all
the notifications were enabled in ucsi_init().
Fixes: 71a1fa0df2 ("usb: typec: ucsi: Store the notification mask")
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200108131347.43217-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use "/*" for non-kernel-doc comments instead of "/**", which is
intended to be used only for kernel-doc notation.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/88821011-2128-a8dd-68b8-c5ae8f43271f@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to enforce suspend/resume ordering, this commit creates link
between phy consumers and phy devices. This link avoids to suspend phy
before phy consumers.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
[jonathanh@nvidia.com: Fix an abort when of_phy_get() returns error]
Signed-off-by: Jonathan Hunter <jonathanh@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
It turns out that even though endpoints with a maxpacket length of 0
aren't useful for data transfer, the descriptors do serve other
purposes. In particular, skipping them will also skip over other
class-specific descriptors for classes such as UVC. This unexpected
side effect has caused some UVC cameras to stop working.
In addition, the USB spec requires that when isochronous endpoint
descriptors are present in an interface's altsetting 0 (which is true
on some devices), the maxpacket size _must_ be set to 0. Warning
about such things seems like a bad idea.
This patch updates an earlier commit which would log a warning and
skip these endpoint descriptors. Now we only log a warning, and we
don't even do that for isochronous endpoints in altsetting 0.
We don't need to worry about preventing endpoints with maxpacket = 0
from ever being used for data transfers; usb_submit_urb() already
checks for this.
Reported-and-tested-by: Roger Whittaker <Roger.Whittaker@suse.com>
Fixes: d482c7bb05 ("USB: Skip endpoints with 0 maxpacket length")
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://marc.info/?l=linux-usb&m=157790377329882&w=2
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2001061040270.1514-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Augmented Power Delivery Objects (A)PDO_s are used by USB-C
PD power adapters to advertize the voltages and currents
they support. There can be up to 7 PDO_s but before PPS
(programmable power supply) there were seldom more than 4
or 5. Recently Samsung released an optional PPS 45 Watt power
adapter (EP-TA485) that has 7 PDO_s. It is for the Galaxy 10+
tablet and charges it quicker than the adapter supplied at
purchase. The EP-TA485 causes an overzealous WARN_ON to soil
the log plus it miscalculates the number of bytes to read.
So this bug has been there for some time but goes
undetected for the majority of USB-C PD power adapters on
the market today that have 6 or less PDO_s. That may soon
change as more USB-C PD adapters with PPS come to market.
Tested on a EP-TA485 and an older Lenovo PN: SA10M13950
USB-C 65 Watt adapter (without PPS and has 4 PDO_s) plus
several other PD power adapters.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191230033544.1809-1-dgilbert@interlog.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's a couple of new modem device ids, including a new quirk for
devices that expect zero-length packets.
Due to the holidays, only the first one has been in linux-next and with
no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXg3MPAAKCRALxc3C7H1l
CMKsAQD5gVqptg42f9oMYnFlAqxKVjnnxxj2FqXDKh8qGiNNUAEAsnGkBp/ZO+wx
3wUxcp6opRIk1ziIvGzY3QIpf/ft6wY=
=u0Ys
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.5-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.5-rc5
Here's a couple of new modem device ids, including a new quirk for
devices that expect zero-length packets.
Due to the holidays, only the first one has been in linux-next and with
no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-5.5-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add ZLP support for 0x1bc7/0x9010
USB: serial: option: add Telit ME910G1 0x110a composition
The USB_OCTEON_EHCI is deprecated and only selects proper driver so
there is no need to compile test it. Since it selects
USB_EHCI_BIG_ENDIAN_MMIO it causes compilation failures on certain big
endian architectures (e.g. m68k):
In file included from drivers/usb/host/ehci-mxc.c:19:0:
drivers/usb/host/ehci.h: In function ‘ehci_readl’:
drivers/usb/host/ehci.h:743:3: error:
implicit declaration of function ‘readl_be’ [-Werror=implicit-function-declaration]
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/1577778392-570-1-git-send-email-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the USB3503 to pick GPIO descriptors from the
device tree instead of iteratively picking out GPIO number
references and then referencing these from the global GPIO
numberspace.
The USB3503 is only used from device tree among the in-tree
platforms. If board files would still desire to use it they can
provide machine descriptor tables.
Make sure to preserve semantics such as the reset delay
introduced by Stefan.
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[mszyprow: invert the logic behind reset GPIO line]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20191211145226.25074-1-m.szyprowski@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Renesas USBHS driver includes a bit of surplus headers
and uses the old GPIO API so let's switch it to use the
GPIO descriptor.
I noticed that the enable_gpio inside renesas_usbhs_driver_param
isn't really referenced anywhere, and it is also the wrong
type (u32) so let's just delete it and use a local variable
instead.
Cc: Eugeniu Rosca <erosca@de.adit-jv.com>
Cc: Veeraiyan Chidambaram <veeraiyan.chidambaram@in.bosch.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191217141241.57639-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of the USB phy drivers can be compile tested to increase build
coverage.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20191230172215.17370-2-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of the USB host drivers can be compile tested to increase build
coverage. Add 'if' conditional to 'default y' so they will not get
enabled by default on all other architectures.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20191230172215.17370-1-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CCGx controller used on NVIDIA GPU card has two separate display
altmode for two DP pin assignments. UCSI specification doesn't
prohibits using separate display altmode.
Current UCSI Type-C framework expects only one display altmode for
all DP pin assignment. This patch squashes two separate display
altmode into single altmode to support controllers with separate
display altmode. We first read all the alternate modes of connector
and then run through it to know if there are separate display
altmodes. If so, it prepares a new port altmode set after squashing
two or more separate altmodes into one.
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20191230133431.63445-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver needs to ignore any Connector Change Events
before the Connector Change Indication notifications have
actually been enabled. This adds a check to
ucsi_connector_change() function to make sure the function
does not try to process the event unless the Connector
Change notifications have been enabled.
It is quite common that the firmware representing the "PPM"
(Platform Policy Manager) starts generating Connector Change
notifications even when only the Command Completion
notifications are enabled.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20191230133431.63445-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mtk-xhci platform glue sets the DMA mask to 32 bits on its own,
which was needed before commit fda182d80a ("usb: xhci: configure
32-bit DMA if the controller does not support 64-bit DMA"), but now it
has no effect, because xhci_gen_setup() sets it up for us according to
hardware capabilities. Remove the useless code.
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Link: https://lore.kernel.org/r/20191219093954.163417-1-tfiga@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AB8505 supports an "UART carkit mode" which makes UART accessible
through the USB connector. Upon detection of the UART cable,
this mode has to be manually enabled by:
1. Turning on the PHY in peripheral mode
2. Reconfiguring PHY/pins to route UART signals to USB pins
At the moment, we do not handle the UART link statuses at all,
which means that UART stops working as soon as phy-ab8500-usb is loaded
(since we disable the PHY after initialization).
Keeping UART working if the cable is inserted before turning on the device
is quite simple: In this case, early boot firmware has already set up
the necessary PHY/pin configuration. The presence of the UART cable
is reported by a special value in the USB link status register.
We can check for that value in ab8505_usb_link_status_update()
and set the PHY back to peripheral mode to restore UART.
(Note: This will result in some minor garbage since we still
temporarily disable the PHY during initialization...)
Fully implementing this feature is more complicated:
For some reason, AB8505 does not update UART link status after bootup.
Regular USB cables work fine, but the link status register does not change
its state if an UART cable is inserted/removed.
It seems likely that the hardware is not actually capable of detecting
UART cables autonomously. In addition to the USB link status register,
implementations in the vendor kernel also manually measure
the ID resistance to detect additional cable types. For UART cables,
the USB link status register might simply reflect the PHY configuration
instead of the actual link status.
Implementing that functionality requires significant additions,
so for now just implement the simple case. This allows using UART
when inserting the cable before turning on the device.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191218203450.71037-1-stephan@gerhold.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some special dance is needed to initialize the HSIC port.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20191221065008.266445-2-lkundrak@v3.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is merely a cleanup. None of these is used anywhere.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20191221065008.266445-4-lkundrak@v3.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We may be using a NOP transceiver and those are treated specially by the
USB core and return -ENODEV with devm_phy_get().
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20191221065008.266445-3-lkundrak@v3.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On shutdown, ehci_power_off() is called unconditionally to power off
each port, even if it was never called to power on the port.
For chipidea, this results in a call to ehci_ci_portpower() with a request
to power off ports even if the port was never powered on.
This results in the following warning from the regulator code.
WARNING: CPU: 0 PID: 182 at drivers/regulator/core.c:2596 _regulator_disable+0x1a8/0x210
unbalanced disables for usb_otg2_vbus
Modules linked in:
CPU: 0 PID: 182 Comm: init Not tainted 5.4.6 #1
Hardware name: Freescale i.MX7 Dual (Device Tree)
[<c0313658>] (unwind_backtrace) from [<c030d698>] (show_stack+0x10/0x14)
[<c030d698>] (show_stack) from [<c1133afc>] (dump_stack+0xe0/0x10c)
[<c1133afc>] (dump_stack) from [<c0349098>] (__warn+0xf4/0x10c)
[<c0349098>] (__warn) from [<c0349128>] (warn_slowpath_fmt+0x78/0xbc)
[<c0349128>] (warn_slowpath_fmt) from [<c09f36ac>] (_regulator_disable+0x1a8/0x210)
[<c09f36ac>] (_regulator_disable) from [<c09f374c>] (regulator_disable+0x38/0xe8)
[<c09f374c>] (regulator_disable) from [<c0df7bac>] (ehci_ci_portpower+0x38/0xdc)
[<c0df7bac>] (ehci_ci_portpower) from [<c0db4fa4>] (ehci_port_power+0x50/0xa4)
[<c0db4fa4>] (ehci_port_power) from [<c0db5420>] (ehci_silence_controller+0x5c/0xc4)
[<c0db5420>] (ehci_silence_controller) from [<c0db7644>] (ehci_stop+0x3c/0xcc)
[<c0db7644>] (ehci_stop) from [<c0d5bdc4>] (usb_remove_hcd+0xe0/0x19c)
[<c0d5bdc4>] (usb_remove_hcd) from [<c0df7638>] (host_stop+0x38/0xa8)
[<c0df7638>] (host_stop) from [<c0df2f34>] (ci_hdrc_remove+0x44/0xe4)
...
Keeping track of the power enable state avoids the warning and traceback.
Fixes: c8679a2fb8 ("usb: chipidea: host: add portpower override")
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Cc: Peter Chen <peter.chen@freescale.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20191226155754.25451-1-linux@roeck-us.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IRQ handler was passed a pointer to a struct dma_controller, but the
argument was then casted to a pointer to a struct musb_dma_controller.
Fixes: 427c4f3334 ("usb: struct device - replace bus_id with dev_name(), dev_set_name()")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20191216161844.772-2-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid printing any error message if the error code is -EPROBE_DEFER.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20191216162432.1256-1-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without this, this new driver fails to link:
drivers/usb/gadget/udc/tegra-xudc.o: In function `tegra_xudc_remove':
tegra-xudc.c:(.text+0x19d4): undefined reference to `usb_role_switch_unregister'
drivers/usb/gadget/udc/tegra-xudc.o: In function `tegra_xudc_probe':
tegra-xudc.c:(.text+0x2a34): undefined reference to `usb_role_switch_register'
drivers/usb/gadget/udc/tegra-xudc.o: In function `tegra_xudc_usb_role_sw_work':
tegra-xudc.c:(.text+0x4b64): undefined reference to `usb_role_switch_get_role'
Fixes: 49db427232 ("usb: gadget: Add UDC driver for tegra XUSB device mode controller")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20191216131831.3228566-1-arnd@arndb.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Amend the endpoint-descriptor sanity checks to detect all duplicate
endpoint addresses in a configuration.
Commit 0a8fd13462 ("USB: fix problems with duplicate endpoint
addresses") added a check for duplicate endpoint addresses within a
single alternate setting, but did not look for duplicate addresses in
other interfaces.
The current check would also not detect all duplicate addresses when one
endpoint is as a (bi-directional) control endpoint.
This specifically avoids overwriting the endpoint entries in struct
usb_device when enabling a duplicate endpoint, something which could
potentially lead to crashes or leaks, for example, when endpoints are
later disabled.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20191219161016.6695-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Telit FN980 flashing device 0x1bc7/0x9010 requires zero packet
to be sent if out data size is is equal to the endpoint max size.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
[ johan: switch operands in conditional ]
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The following build warning is seen if CONFIG_PM is disabled.
drivers/usb/host/xhci-pci.c:498:13: warning:
unused function 'xhci_pci_shutdown'
Fixes: f2c710f7dc ("usb: xhci: only set D3hot for pci device")
Cc: Henry Lin <henryl@nvidia.com>
Cc: stable@vger.kernel.org # all stable releases with f2c710f7dc
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20191218011911.6907-1-linux@roeck-us.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a transaction error happens in vhci_recv_ret_submit(), event
handler closes connection and changes port status to kick hub_event.
Then hub tries to flush the endpoint URBs, but that causes infinite
loop between usb_hub_flush_endpoint() and vhci_urb_dequeue() because
"vhci_priv" in vhci_urb_dequeue() was already released by
vhci_recv_ret_submit() before a transmission error occurred. Thus,
vhci_urb_dequeue() terminates early and usb_hub_flush_endpoint()
continuously calls vhci_urb_dequeue().
The root cause of this issue is that vhci_recv_ret_submit()
terminates early without giving back URB when transaction error
occurs in vhci_recv_ret_submit(). That causes the error URB to still
be linked at endpoint list without “vhci_priv".
So, in the case of transaction error in vhci_recv_ret_submit(),
unlink URB from the endpoint, insert proper error code in
urb->status and give back URB.
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Signed-off-by: Suwan Kim <suwan.kim027@gmail.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20191213023055.19933-3-suwan.kim027@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When vhci uses SG and receives data whose size is smaller than SG
buffer size, it tries to receive more data even if it acutally
receives all the data from the server. If then, it erroneously adds
error event and triggers connection shutdown.
vhci-hcd should check if it received all the data even if there are
more SG entries left. So, check if it receivces all the data from
the server in for_each_sg() loop.
Fixes: ea44d19076 ("usbip: Implement SG support to vhci-hcd and stub driver")
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Signed-off-by: Suwan Kim <suwan.kim027@gmail.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191213023055.19933-2-suwan.kim027@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/usb/gadget/Kconfig includes drivers/usb/gadget/legacy/Kconfig
inside the 'choice' block. The current Kconfig allows this, but I'd
like to discourage this usage.
People tend to mess up the structure without noticing that entire
drivers/usb/gadget/legacy/Kconfig is placed in the choice context.
In fact, legacy/Kconfig mixes up bool and tristate in the choice,
and creates nested choice, etc.
This commit does not change the behavior, but it will help people
notice how badly this Kconfig file is written.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20191211073857.16780-1-masahiroy@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PCM core deals the empty ioctl field now as default.
Let's kill the redundant lines.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20191210141822.18705-3-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up the driver with the new managed buffer allocation API.
The hw_params and hw_free callbacks became superfluous and dropped.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20191210141822.18705-2-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When disconnecting a USB hub that has some child device(s) connected to it
(such as a USB mouse), then the stack tries to clear halt and
reset device(s) which are _already_ physically disconnected.
The issue has been reproduced with:
CPU: IMX6D5EYM10AD or MCIMX6D5EYM10AE.
SW: U-Boot 2019.07 and kernel 4.19.40.
CPU: HP Proliant Microserver Gen8.
SW: Linux version 4.2.3-300.fc23.x86_64
In this situation there will be error bit for MMF active yet the
CERR equals EHCI_TUNE_CERR + halt. Existing implementation
interprets this as a stall [1] (chapter 8.4.5).
The possible conditions when the MMF will be active + halt
can be found from [2] (Table 4-13).
Fix for the issue is to check whether MMF is active and PID Code is
IN before checking for the stall. If these conditions are true then
it is not a stall.
What happens after the fix is that when disconnecting a hub with
attached device(s) the situation is not interpret as a stall.
[1] [https://www.usb.org/document-library/usb-20-specification, usb_20.pdf]
[2] [https://www.intel.com/content/dam/www/public/us/en/documents/
technical-specifications/ehci-specification-for-usb.pdf]
Signed-off-by: Erkka Talvitie <erkka.talvitie@vincit.fi>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/ef70941d5f349767f19c0ed26b0dd9eed8ad81bb.1576050523.git.erkka.talvitie@vincit.fi
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following compile error:
drivers/usb/typec/tcpm/fusb302.o: In function `tcpm_get_current_limit':
fusb302.c:(.text+0x3ee): undefined reference to `extcon_get_state'
fusb302.c:(.text+0x422): undefined reference to `extcon_get_state'
fusb302.c:(.text+0x450): undefined reference to `extcon_get_state'
fusb302.c:(.text+0x48c): undefined reference to `extcon_get_state'
drivers/usb/typec/tcpm/fusb302.o: In function `fusb302_probe':
fusb302.c:(.text+0x980): undefined reference to `extcon_get_extcon_dev'
make: *** [vmlinux] Error 1
It is because EXTCON is build as a module, but FUSB302 is not.
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1576239378-50795-1-git-send-email-zhongjiang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some small USB driver fixes for reported issues for 5.5-rc2
There's the usual gadget and xhci fixes, as well as some other problems
that syzbot has been finding during it's fuzzing runs. Full details are
in the shortlog.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXfT++A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yminwCgyTXywlBkMdzz22vA9g12euh2LlEAnRyLI6DQ
Jk4FJOtW87JIYSSRjAhh
=3prZ
-----END PGP SIGNATURE-----
Merge tag 'usb-5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB driver fixes for reported issues for 5.5-rc2
There's the usual gadget and xhci fixes, as well as some other
problems that syzbot has been finding during it's fuzzing runs. Full
details are in the shortlog.
All of these have been in linux-next with no reported issues"
* tag 'usb-5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (21 commits)
usb: dwc3: pci: add ID for the Intel Comet Lake -H variant
xhci: make sure interrupts are restored to correct state
xhci: handle some XHCI_TRUST_TX_LENGTH quirks cases as default behaviour.
xhci: Increase STS_HALT timeout in xhci_suspend()
usb: xhci: only set D3hot for pci device
xhci: fix USB3 device initiated resume race with roothub autosuspend
xhci: Fix memory leak in xhci_add_in_port()
USB: Fix incorrect DMA allocations for local memory pool drivers
usb: gadget: fix wrong endpoint desc
usb: dwc3: ep0: Clear started flag on completion
usb: dwc3: gadget: Clear started flag for non-IOC
usb: dwc3: gadget: Fix logical condition
USB: atm: ueagle-atm: add missing endpoint check
USB: adutux: fix interface sanity check
USB: idmouse: fix interface sanity checks
USB: serial: io_edgeport: fix epic endpoint lookup
usb: mon: Fix a deadlock in usbmon between mmap and read
usb: common: usb-conn-gpio: Don't log an error on probe deferral
usb: core: urb: fix URB structure initialization function
usb: typec: fix use after free in typec_register_port()
...
The original ID that was added for Comet Lake PCH was
actually for the -LP (low power) variant even though the
constant for it said CMLH. Changing that while at it.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191212093713.60614-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
spin_unlock_irqrestore() might be called with stale flags after
reading port status, possibly restoring interrupts to a incorrect
state.
If a usb2 port just finished resuming while the port status is read
the spin lock will be temporary released and re-acquired in a separate
function. The flags parameter is passed as value instead of a pointer,
not updating flags properly before the final spin_unlock_irqrestore()
is called.
Cc: <stable@vger.kernel.org> # v3.12+
Fixes: 8b3d45705e ("usb: Fix xHCI host issues on remote wakeup.")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20191211142007.8847-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci driver claims it needs XHCI_TRUST_TX_LENGTH quirk for both
Broadcom/Cavium and a Renesas xHC controllers.
The quirk was inteded for handling false "success" complete event for
transfers that had data left untransferred.
These transfers should complete with "short packet" events instead.
In these two new cases the false "success" completion is reported
after a "short packet" if the TD consists of several TRBs.
xHCI specs 4.10.1.1.2 say remaining TRBs should report "short packet"
as well after the first short packet in a TD, but this issue seems so
common it doesn't make sense to add the quirk for all vendors.
Turn these events into short packets automatically instead.
This gets rid of the "The WARN Successful completion on short TX for
slot 1 ep 1: needs XHCI_TRUST_TX_LENGTH quirk" warning in many cases.
Cc: <stable@vger.kernel.org>
Reported-by: Eli Billauer <eli.billauer@gmail.com>
Reported-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Eli Billauer <eli.billauer@gmail.com>
Tested-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20191211142007.8847-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xhci driver cannot call pci_set_power_state() on non-pci xhci host
controllers. For example, NVIDIA Tegra XHCI host controller which acts
as platform device with XHCI_SPURIOUS_WAKEUP quirk set in some platform
hits this issue during shutdown.
Cc: <stable@vger.kernel.org>
Fixes: 638298dc66 ("xhci: Fix spurious wakeups after S5 on Haswell")
Signed-off-by: Henry Lin <henryl@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20191211142007.8847-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A race in xhci USB3 remote wake handling may force device back to suspend
after it initiated resume siganaling, causing a missed resume event or warm
reset of device.
When a USB3 link completes resume signaling and goes to enabled (UO)
state a interrupt is issued and the interrupt handler will clear the
bus_state->port_remote_wakeup resume flag, allowing bus suspend.
If the USB3 roothub thread just finished reading port status before
the interrupt, finding ports still in suspended (U3) state, but hasn't
yet started suspending the hub, then the xhci interrupt handler will clear
the flag that prevented roothub suspend and allow bus to suspend, forcing
all port links back to suspended (U3) state.
Example case:
usb_runtime_suspend() # because all ports still show suspended U3
usb_suspend_both()
hub_suspend(); # successful as hub->wakeup_bits not set yet
==> INTERRUPT
xhci_irq()
handle_port_status()
clear bus_state->port_remote_wakeup
usb_wakeup_notification()
sets hub->wakeup_bits;
kick_hub_wq()
<== END INTERRUPT
hcd_bus_suspend()
xhci_bus_suspend() # success as port_remote_wakeup bits cleared
Fix this by increasing roothub usage count during port resume to prevent
roothub autosuspend, and by making sure bus_state->port_remote_wakeup
flag is only cleared after resume completion is visible, i.e.
after xhci roothub returned U0 or other non-U3 link state link on a
get port status request.
Issue rootcaused by Chiasheng Lee
Cc: <stable@vger.kernel.org>
Cc: Lee, Hou-hsun <hou-hsun.lee@intel.com>
Reported-by: Lee, Chiasheng <chiasheng.lee@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20191211142007.8847-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only four patches here this time around. Three of them are on dwc3
fixing some small bugs related to our 'started' flag.
None are major fixes but they're important nevertheless.
-----BEGIN PGP SIGNATURE-----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=Dck/
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
USB: fixes for v5.5-rc2
Only four patches here this time around. Three of them are on dwc3
fixing some small bugs related to our 'started' flag.
None are major fixes but they're important nevertheless.
* tag 'fixes-for-v5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
usb: gadget: fix wrong endpoint desc
usb: dwc3: ep0: Clear started flag on completion
usb: dwc3: gadget: Clear started flag for non-IOC
usb: dwc3: gadget: Fix logical condition
Fix commit 7b81cb6bdd ("usb: add a HCD_DMA flag instead of
guestimating DMA capabilities") where local memory USB drivers
erroneously allocate DMA memory instead of pool memory, causing
OHCI Unrecoverable Error, disabled
HC died; cleaning up
The order between hcd_uses_dma() and hcd->localmem_pool is now
arranged as in hcd_buffer_alloc() and hcd_buffer_free(), with the
test for hcd->localmem_pool placed first.
As an alternative, one might consider adjusting hcd_uses_dma() with
static inline bool hcd_uses_dma(struct usb_hcd *hcd)
{
- return IS_ENABLED(CONFIG_HAS_DMA) && (hcd->driver->flags & HCD_DMA);
+ return IS_ENABLED(CONFIG_HAS_DMA) &&
+ (hcd->driver->flags & HCD_DMA) &&
+ (hcd->localmem_pool == NULL);
}
One can also consider unsetting HCD_DMA for local memory pool drivers.
Fixes: 7b81cb6bdd ("usb: add a HCD_DMA flag instead of guestimating DMA capabilities")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Fredrik Noring <noring@nocrew.org>
Link: https://lore.kernel.org/r/20191210172905.GA52526@sx9
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gadget driver should always use config_ep_by_speed() to initialize
usb_ep struct according to usb device's operating speed. Otherwise,
usb_ep struct may be wrong if usb devcie's operating speed is changed.
The key point in this patch is that we want to make sure the desc pointer
in usb_ep struct will be set to NULL when gadget is disconnected.
This will force it to call config_ep_by_speed() to correctly initialize
usb_ep struct based on the new operating speed when gadget is
re-connected later.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: EJ Hsu <ejh@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Clear ep0's DWC3_EP_TRANSFER_STARTED flag if the END_TRANSFER command is
completed. Otherwise, we can't start control transfer again after
END_TRANSFER.
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Normally the END_TRANSFER command completion handler will clear the
DWC3_EP_TRANSFER_STARTED flag. However, if the command was sent without
interrupt on completion, then the flag will not be cleared. Make sure to
clear the flag in this case.
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch corrects the condition to kick the transfer without
giving back the requests when either request has remaining data
or when there are pending SGs. The && check was introduced during
spliting up the dwc3_gadget_ep_cleanup_completed_requests() function.
Fixes: f38e35dd84 ("usb: dwc3: gadget: split dwc3_gadget_ep_cleanup_completed_requests()")
Cc: stable@vger.kernel.org
Signed-off-by: Tejas Joglekar <joglekar@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Make sure that the interrupt interface has an endpoint before trying to
access its endpoint descriptors to avoid dereferencing a NULL pointer.
The driver binds to the interrupt interface with interface number 0, but
must not assume that this interface or its current alternate setting are
the first entries in the corresponding configuration arrays.
Fixes: b72458a80c ("[PATCH] USB: Eagle and ADI 930 usb adsl modem driver")
Cc: stable <stable@vger.kernel.org> # 2.6.16
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191210112601.3561-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: 03270634e2 ("USB: Add ADU support for Ontrak ADU devices")
Cc: stable <stable@vger.kernel.org> # 2.6.19
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191210112601.3561-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191210112601.3561-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to use the current alternate setting when looking up the
endpoints on epic devices to avoid binding to an invalid interface.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: 6e8cf7751f ("USB: add EPIC support to the io_edgeport driver")
Cc: stable <stable@vger.kernel.org> # 2.6.21
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191210112601.3561-5-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The problem arises because our read() function grabs a lock of the
circular buffer, finds something of interest, then invokes copy_to_user()
straight from the buffer, which in turn takes mm->mmap_sem. In the same
time, the callback mon_bin_vma_fault() is invoked under mm->mmap_sem.
It attempts to take the fetch lock and deadlocks.
This patch does away with protecting of our page list with any
semaphores, and instead relies on the kernel not close the device
while mmap is active in a process.
In addition, we prohibit re-sizing of a buffer while mmap is active.
This way, when (now unlocked) fault is processed, it works with the
page that is intended to be mapped-in, and not some other random page.
Note that this may have an ABI impact, but hopefully no legitimate
program is this wrong.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Reported-by: syzbot+56f9673bb4cdcbeb0e92@syzkaller.appspotmail.com
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: 46eb14a6e1 ("USB: fix usbmon BUG trigger")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191204203941.3503452b@suzdal.zaitcev.lan
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch makes the printout of the error message for failing to get a
VBUS regulator handle conditional on the error code being something other
than -EPROBE_DEFER.
Deferral is a normal thing, we don't need an error message for this.
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Nagarjuna Kristam <nkristam@nvidia.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191128134358.3880498-2-bryan.odonoghue@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Explicitly initialize URB structure urb_list field in usb_init_urb().
This field can be potentially accessed uninitialized and its
initialization is coherent with the usage of list_del_init() in
usb_hcd_unlink_urb_from_ep() and usb_giveback_urb_bh() and its
explicit initialization in usb_hcd_submit_urb() error path.
Signed-off-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191127160355.GA27196@ingrassia.epigenesys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Free the sw structure only after we are done using it.
This patch just moves the put_device() down a bit to avoid the
use after free.
Fixes: 5c54fcac9a ("usb: roles: Take care of driver module reference counting")
Signed-off-by: Wen Yang <wenyang@linux.alibaba.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Cc: stable <stable@vger.kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20191124142236.25671-1-wenyang@linux.alibaba.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This implements basic engine-level powergate support which allows the
XUSB controller to be put into a low power mode on system sleep and get
it out of that low power mode again on resume.
Based on work by JC Kuo <jckuo@nvidia.com>.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20191206140653.2085561-11-thierry.reding@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Define the offsets of the registers that need to be saved on suspend and
restored on resume for the various NVIDIA Tegra generations supported by
the XUSB driver.
Based on work by JC Kuo <jckuo@nvidia.com>.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20191206140653.2085561-10-thierry.reding@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The XUSB controller contains registers that need to be saved on suspend
and restored on resume in addition to the XHCI specific registers. Add
support for saving and restoring the XUSB specific context.
Based on work by JC Kuo <jckuo@nvidia.com>.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20191206140653.2085561-9-thierry.reding@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A number of things can currently go wrong after the XUSB controller has
been enabled, which means that it might need to be disabled again before
it has ever been used.
Avoid this by delaying runtime PM enablement until it's really required
right before registers are accessed for the first time.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20191206140653.2085561-8-thierry.reding@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The base address of the XUSB controller's registers is already stored in
the HCD. Move assignment to the HCD fields to an earlier point so that
they can be reused in the tegra_xusb_config() function. This avoids the
need to pass the base address as an extra parameter, which in turn comes
in handy in subsequent patches that need to call this function from the
suspend/resume paths where these values are no longer readily available.
Based on work by JC Kuo <jckuo@nvidia.com>.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20191206140653.2085561-7-thierry.reding@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extract a helper that enables message generation from the firmware. This
removes clutter from tegra_xusb_probe() and will also come in useful for
subsequent patches that introduce suspend/resume support.
Based on work by JC Kuo <jckuo@nvidia.com>.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20191206140653.2085561-6-thierry.reding@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Falcon CPU state is a suboptimal indicator for firmware readiness,
since the Falcon can be in a running state if the firmware is handling
port state changes or running other tasks. Instead, the driver should
check the STS_CNR bit to determine whether or not the firmware has been
successfully loaded and is ready for XHCI operation.
Based on work by JC Kuo <jckuo@nvidia.com>.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20191206140653.2085561-5-thierry.reding@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not use a fixed duration sleep to wait for the DMA controller to
become ready. Instead, poll the L2IMEMOP_RESULT register for the VLD
flag to determine when the XUSB controller's DMA master is ready.
Based on work by JC Kuo <jckuo@nvidia.com>.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20191206140653.2085561-4-thierry.reding@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Subsequent patches for system suspend/resume support will need to reload
the firmware on resume. Since the firmware remains in system memory, the
driver doesn't need to reload it from the filesystem. However, the XUSB
controller will be reset across suspend/resume, so it needs to load the
firmware into its microcontroller on resume.
Split the firmware request and the firmware load code into two separate
functions so that the driver can reuse the firmware in system memory to
reload the microcontroller on resume.
Based on work by JC Kuo <jckuo@nvidia.com>.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20191206140653.2085561-3-thierry.reding@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tegra_xusb_mbox_regs structure was misspelled tega_xusb_mbox_regs.
Fortunately this was done consistently so it didn't cause any issues.
Reviewed-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20191206140653.2085561-2-thierry.reding@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ehci_sh_platdata was never used, remove it. It can be resurrected from
git history when needed.
This basically reverts commit 3e0c70d050 ("usb: ehci-sh: Add PHY
init function with platform data").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Link: https://lore.kernel.org/r/20191206132849.29406-1-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace all the occurrences of FIELD_SIZEOF() with sizeof_field() except
at places where these are defined. Later patches will remove the unused
definition of FIELD_SIZEOF().
This patch is generated using following script:
EXCLUDE_FILES="include/linux/stddef.h|include/linux/kernel.h"
git grep -l -e "\bFIELD_SIZEOF\b" | while read file;
do
if [[ "$file" =~ $EXCLUDE_FILES ]]; then
continue
fi
sed -i -e 's/\bFIELD_SIZEOF\b/sizeof_field/g' $file;
done
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Link: https://lore.kernel.org/r/20190924105839.110713-3-pankaj.laxminarayan.bharadiya@intel.com
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David Miller <davem@davemloft.net> # for net
Add kcov_remote_start()/kcov_remote_stop() annotations to the
hub_event() function, which is responsible for processing events on USB
buses, in particular events that happen during USB device enumeration.
Since hub_event() is run in a global background kernel thread (see
Documentation/dev-tools/kcov.rst for details), each USB bus gets a
unique global handle from the USB subsystem kcov handle range. As the
result kcov can now be used to collect coverage from events that happen
on a particular USB bus.
[akpm@linux-foundation.org: avoid patch conflicts to make life easier for Andrew]
Link: http://lkml.kernel.org/r/de4fe1c219db2d002d905dc1736e2a3bfa1db997.1572366574.git.andreyknvl@google.com
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Alexander Potapenko <glider@google.com>
Cc: Anders Roxell <anders.roxell@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Windsor <dwindsor@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Elena Reshetova <elena.reshetova@intel.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Marco Elver <elver@google.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----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=uUXw
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Warn if a host bridge has no NUMA info (Yunsheng Lin)
- Add PCI_STD_NUM_BARS for the number of standard BARs (Denis
Efremov)
Resource management:
- Fix boot-time Embedded Controller GPE storm caused by incorrect
resource assignment after ACPI Bus Check Notification (Mika
Westerberg)
- Protect pci_reassign_bridge_resources() against concurrent
addition/removal (Benjamin Herrenschmidt)
- Fix bridge dma_ranges resource list cleanup (Rob Herring)
- Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters to control
the MMIO and prefetchable MMIO window sizes of hotplug bridges
independently (Nicholas Johnson)
- Fix MMIO/MMIO_PREF window assignment that assigned more space than
desired (Nicholas Johnson)
- Only enforce bus numbers from bridge EA if the bridge has EA
devices downstream (Subbaraya Sundeep)
- Consolidate DT "dma-ranges" parsing and convert all host drivers to
use shared parsing (Rob Herring)
Error reporting:
- Restore AER capability after resume (Mayurkumar Patel)
- Add PoisonTLPBlocked AER counter (Rajat Jain)
- Use for_each_set_bit() to simplify AER code (Andy Shevchenko)
- Fix AER kernel-doc (Andy Shevchenko)
- Add "pcie_ports=dpc-native" parameter to allow native use of DPC
even if platform didn't grant control over AER (Olof Johansson)
Hotplug:
- Avoid returning prematurely from sysfs requests to enable or
disable a PCIe hotplug slot (Lukas Wunner)
- Don't disable interrupts twice when suspending hotplug ports (Mika
Westerberg)
- Fix deadlocks when PCIe ports are hot-removed while suspended (Mika
Westerberg)
Power management:
- Remove unnecessary ASPM locking (Bjorn Helgaas)
- Add support for disabling L1 PM Substates (Heiner Kallweit)
- Allow re-enabling Clock PM after it has been disabled (Heiner
Kallweit)
- Add sysfs attributes for controlling ASPM link states (Heiner
Kallweit)
- Remove CONFIG_PCIEASPM_DEBUG, including "link_state" and "clk_ctl"
sysfs files (Heiner Kallweit)
- Avoid AMD FCH XHCI USB PME# from D0 defect that prevents wakeup on
USB 2.0 or 1.1 connect events (Kai-Heng Feng)
- Move power state check out of pci_msi_supported() (Bjorn Helgaas)
- Fix incorrect MSI-X masking on resume and revert related nvme quirk
for Kingston NVME SSD running FW E8FK11.T (Jian-Hong Pan)
- Always return devices to D0 when thawing to fix hibernation with
drivers like mlx4 that used legacy power management (previously we
only did it for drivers with new power management ops) (Dexuan Cui)
- Clear PCIe PME Status even for legacy power management (Bjorn
Helgaas)
- Fix PCI PM documentation errors (Bjorn Helgaas)
- Use dev_printk() for more power management messages (Bjorn Helgaas)
- Apply D2 delay as milliseconds, not microseconds (Bjorn Helgaas)
- Convert xen-platform from legacy to generic power management (Bjorn
Helgaas)
- Removed unused .resume_early() and .suspend_late() legacy power
management hooks (Bjorn Helgaas)
- Rearrange power management code for clarity (Rafael J. Wysocki)
- Decode power states more clearly ("4" or "D4" really refers to
"D3cold") (Bjorn Helgaas)
- Notice when reading PM Control register returns an error (~0)
instead of interpreting it as being in D3hot (Bjorn Helgaas)
- Add missing link delays required by the PCIe spec (Mika Westerberg)
Virtualization:
- Move pci_prg_resp_pasid_required() to CONFIG_PCI_PRI (Bjorn
Helgaas)
- Allow VFs to use PRI (the PF PRI is shared by the VFs, but the code
previously didn't recognize that) (Kuppuswamy Sathyanarayanan)
- Allow VFs to use PASID (the PF PASID capability is shared by the
VFs, but the code previously didn't recognize that) (Kuppuswamy
Sathyanarayanan)
- Disconnect PF and VF ATS enablement, since ATS in PFs and
associated VFs can be enabled independently (Kuppuswamy
Sathyanarayanan)
- Cache PRI and PASID capability offsets (Kuppuswamy Sathyanarayanan)
- Cache the PRI PRG Response PASID Required bit (Bjorn Helgaas)
- Consolidate ATS declarations in linux/pci-ats.h (Krzysztof
Wilczynski)
- Remove unused PRI and PASID stubs (Bjorn Helgaas)
- Removed unnecessary EXPORT_SYMBOL_GPL() from ATS, PRI, and PASID
interfaces that are only used by built-in IOMMU drivers (Bjorn
Helgaas)
- Hide PRI and PASID state restoration functions used only inside the
PCI core (Bjorn Helgaas)
- Add a DMA alias quirk for the Intel VCA NTB (Slawomir Pawlowski)
- Serialize sysfs sriov_numvfs reads vs writes (Pierre Crégut)
- Update Cavium ACS quirk for ThunderX2 and ThunderX3 (George
Cherian)
- Fix the UPDCR register address in the Intel ACS quirk (Steffen
Liebergeld)
- Unify ACS quirk implementations (Bjorn Helgaas)
Amlogic Meson host bridge driver:
- Fix meson PERST# GPIO polarity problem (Remi Pommarel)
- Add DT bindings for Amlogic Meson G12A (Neil Armstrong)
- Fix meson clock names to match DT bindings (Neil Armstrong)
- Add meson support for Amlogic G12A SoC with separate shared PHY
(Neil Armstrong)
- Add meson extended PCIe PHY functions for Amlogic G12A USB3+PCIe
combo PHY (Neil Armstrong)
- Add arm64 DT for Amlogic G12A PCIe controller node (Neil Armstrong)
- Add commented-out description of VIM3 USB3/PCIe mux in arm64 DT
(Neil Armstrong)
Broadcom iProc host bridge driver:
- Invalidate iProc PAXB address mapping before programming it
(Abhishek Shah)
- Fix iproc-msi and mvebu __iomem annotations (Ben Dooks)
Cadence host bridge driver:
- Refactor Cadence PCIe host controller to use as a library for both
host and endpoint (Tom Joseph)
Freescale Layerscape host bridge driver:
- Add layerscape LS1028a support (Xiaowei Bao)
Intel VMD host bridge driver:
- Add VMD bus 224-255 restriction decode (Jon Derrick)
- Add VMD 8086:9A0B device ID (Jon Derrick)
- Remove Keith from VMD maintainer list (Keith Busch)
Marvell ARMADA 3700 / Aardvark host bridge driver:
- Use LTSSM state to build link training flag since Aardvark doesn't
implement the Link Training bit (Remi Pommarel)
- Delay before training Aardvark link in case PERST# was asserted
before the driver probe (Remi Pommarel)
- Fix Aardvark issues with Root Control reads and writes (Remi
Pommarel)
- Don't rely on jiffies in Aardvark config access path since
interrupts may be disabled (Remi Pommarel)
- Fix Aardvark big-endian support (Grzegorz Jaszczyk)
Marvell ARMADA 370 / XP host bridge driver:
- Make mvebu_pci_bridge_emul_ops static (Ben Dooks)
Microsoft Hyper-V host bridge driver:
- Add hibernation support for Hyper-V virtual PCI devices (Dexuan
Cui)
- Track Hyper-V pci_protocol_version per-hbus, not globally (Dexuan
Cui)
- Avoid kmemleak false positive on hv hbus buffer (Dexuan Cui)
Mobiveil host bridge driver:
- Change mobiveil csr_read()/write() function names that conflict
with riscv arch functions (Kefeng Wang)
NVIDIA Tegra host bridge driver:
- Fix Tegra CLKREQ dependency programming (Vidya Sagar)
Renesas R-Car host bridge driver:
- Remove unnecessary header include from rcar (Andrew Murray)
- Tighten register index checking for rcar inbound range programming
(Marek Vasut)
- Fix rcar inbound range alignment calculation to improve packing of
multiple entries (Marek Vasut)
- Update rcar MACCTLR setting to match documentation (Yoshihiro
Shimoda)
- Clear bit 0 of MACCTLR before PCIETCTLR.CFINIT per manual
(Yoshihiro Shimoda)
- Add Marek Vasut and Yoshihiro Shimoda as R-Car maintainers (Simon
Horman)
Rockchip host bridge driver:
- Make rockchip 0V9 and 1V8 power regulators non-optional (Robin
Murphy)
Socionext UniPhier host bridge driver:
- Set uniphier to host (RC) mode always (Kunihiko Hayashi)
Endpoint drivers:
- Fix endpoint driver sign extension problem when shifting page
number to phys_addr_t (Alan Mikhak)
Misc:
- Add NumaChip SPDX header (Krzysztof Wilczynski)
- Replace EXTRA_CFLAGS with ccflags-y (Krzysztof Wilczynski)
- Remove unused includes (Krzysztof Wilczynski)
- Removed unused sysfs attribute groups (Ben Dooks)
- Remove PTM and ASPM dependencies on PCIEPORTBUS (Bjorn Helgaas)
- Add PCIe Link Control 2 register field definitions to replace magic
numbers in AMDGPU and Radeon CIK/SI (Bjorn Helgaas)
- Fix incorrect Link Control 2 Transmit Margin usage in AMDGPU and
Radeon CIK/SI PCIe Gen3 link training (Bjorn Helgaas)
- Use pcie_capability_read_word() instead of pci_read_config_word()
in AMDGPU and Radeon CIK/SI (Frederick Lawler)
- Remove unused pci_irq_get_node() Greg Kroah-Hartman)
- Make asm/msi.h mandatory and simplify PCI_MSI_IRQ_DOMAIN Kconfig
(Palmer Dabbelt, Michal Simek)
- Read all 64 bits of Switchtec part_event_bitmap (Logan Gunthorpe)
- Fix erroneous intel-iommu dependency on CONFIG_AMD_IOMMU (Bjorn
Helgaas)
- Fix bridge emulation big-endian support (Grzegorz Jaszczyk)
- Fix dwc find_next_bit() usage (Niklas Cassel)
- Fix pcitest.c fd leak (Hewenliang)
- Fix typos and comments (Bjorn Helgaas)
- Fix Kconfig whitespace errors (Krzysztof Kozlowski)"
* tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (160 commits)
PCI: Remove PCI_MSI_IRQ_DOMAIN architecture whitelist
asm-generic: Make msi.h a mandatory include/asm header
Revert "nvme: Add quirk for Kingston NVME SSD running FW E8FK11.T"
PCI/MSI: Fix incorrect MSI-X masking on resume
PCI/MSI: Move power state check out of pci_msi_supported()
PCI/MSI: Remove unused pci_irq_get_node()
PCI: hv: Avoid a kmemleak false positive caused by the hbus buffer
PCI: hv: Change pci_protocol_version to per-hbus
PCI: hv: Add hibernation support
PCI: hv: Reorganize the code in preparation of hibernation
MAINTAINERS: Remove Keith from VMD maintainer
PCI/ASPM: Remove PCIEASPM_DEBUG Kconfig option and related code
PCI/ASPM: Add sysfs attributes for controlling ASPM link states
PCI: Fix indentation
drm/radeon: Prefer pcie_capability_read_word()
drm/radeon: Replace numbers with PCI_EXP_LNKCTL2 definitions
drm/radeon: Correct Transmit Margin masks
drm/amdgpu: Prefer pcie_capability_read_word()
PCI: uniphier: Set mode register to host mode
drm/amdgpu: Replace numbers with PCI_EXP_LNKCTL2 definitions
...
This is mostly update of the usual drivers: aacraid, ufs, zfcp,
NCR5380, lpfc, qla2xxx, smartpqi, hisi_sas, target, mpt3sas, pm80xx
plus a whole load of minor updates and fixes. The two major core
changes are Al Viro's reworking of sg's handling of copy to/from user,
Ming Lei's removal of the host busy counter to avoid contention in the
multiqueue case and Damien Le Moal's fixing of residual tracking
across error handling.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXeKvHCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishQJMAQDAjlAi
SNfbyndMqyf+rZGWufDI+43Up1VvW9GeWJHeDwEAxfO5XZsCks2uT8UxXhpEp9L7
HkiUww3zbcgl0FWFkUM=
=cdVU
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: aacraid, ufs, zfcp,
NCR5380, lpfc, qla2xxx, smartpqi, hisi_sas, target, mpt3sas, pm80xx
plus a whole load of minor updates and fixes.
The major core changes are Al Viro's reworking of sg's handling of
copy to/from user, Ming Lei's removal of the host busy counter to
avoid contention in the multiqueue case and Damien Le Moal's fixing of
residual tracking across error handling"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (251 commits)
scsi: bnx2fc: timeout calculation invalid for bnx2fc_eh_abort()
scsi: target: core: Fix a pr_debug() argument
scsi: iscsi: Don't send data to unbound connection
scsi: target: iscsi: Wait for all commands to finish before freeing a session
scsi: target: core: Release SPC-2 reservations when closing a session
scsi: target: core: Document target_cmd_size_check()
scsi: bnx2i: fix potential use after free
Revert "scsi: qla2xxx: Fix memory leak when sending I/O fails"
scsi: NCR5380: Add disconnect_mask module parameter
scsi: NCR5380: Unconditionally clear ICR after do_abort()
scsi: NCR5380: Call scsi_set_resid() on command completion
scsi: scsi_debug: num_tgts must be >= 0
scsi: lpfc: use hdwq assigned cpu for allocation
scsi: arcmsr: fix indentation issues
scsi: qla4xxx: fix double free bug
scsi: pm80xx: Modified the logic to collect fatal dump
scsi: pm80xx: Tie the interrupt name to the module instance
scsi: pm80xx: Controller fatal error through sysfs
scsi: pm80xx: Do not request 12G sas speeds
scsi: pm80xx: Cleanup command when a reset times out
...
As part of the cleanup of some remaining y2038 issues, I came to
fs/compat_ioctl.c, which still has a couple of commands that need support
for time64_t.
In completely unrelated work, I spent time on cleaning up parts of this
file in the past, moving things out into drivers instead.
After Al Viro reviewed an earlier version of this series and did a lot
more of that cleanup, I decided to try to completely eliminate the rest
of it and move it all into drivers.
This series incorporates some of Al's work and many patches of my own,
but in the end stops short of actually removing the last part, which is
the scsi ioctl handlers. I have patches for those as well, but they need
more testing or possibly a rewrite.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=lgCl
-----END PGP SIGNATURE-----
Merge tag 'compat-ioctl-5.5' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground
Pull removal of most of fs/compat_ioctl.c from Arnd Bergmann:
"As part of the cleanup of some remaining y2038 issues, I came to
fs/compat_ioctl.c, which still has a couple of commands that need
support for time64_t.
In completely unrelated work, I spent time on cleaning up parts of
this file in the past, moving things out into drivers instead.
After Al Viro reviewed an earlier version of this series and did a lot
more of that cleanup, I decided to try to completely eliminate the
rest of it and move it all into drivers.
This series incorporates some of Al's work and many patches of my own,
but in the end stops short of actually removing the last part, which
is the scsi ioctl handlers. I have patches for those as well, but they
need more testing or possibly a rewrite"
* tag 'compat-ioctl-5.5' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground: (42 commits)
scsi: sd: enable compat ioctls for sed-opal
pktcdvd: add compat_ioctl handler
compat_ioctl: move SG_GET_REQUEST_TABLE handling
compat_ioctl: ppp: move simple commands into ppp_generic.c
compat_ioctl: handle PPPIOCGIDLE for 64-bit time_t
compat_ioctl: move PPPIOCSCOMPRESS to ppp_generic
compat_ioctl: unify copy-in of ppp filters
tty: handle compat PPP ioctls
compat_ioctl: move SIOCOUTQ out of compat_ioctl.c
compat_ioctl: handle SIOCOUTQNSD
af_unix: add compat_ioctl support
compat_ioctl: reimplement SG_IO handling
compat_ioctl: move WDIOC handling into wdt drivers
fs: compat_ioctl: move FITRIM emulation into file systems
gfs2: add compat_ioctl support
compat_ioctl: remove unused convert_in_user macro
compat_ioctl: remove last RAID handling code
compat_ioctl: remove /dev/raw ioctl translation
compat_ioctl: remove PCI ioctl translation
compat_ioctl: remove joystick ioctl translation
...
- improve dma-debug scalability (Eric Dumazet)
- tiny dma-debug cleanup (Dan Carpenter)
- check for vmap memory in dma_map_single (Kees Cook)
- check for dma_addr_t overflows in dma-direct when using
DMA offsets (Nicolas Saenz Julienne)
- switch the x86 sta2x11 SOC to use more generic DMA code
(Nicolas Saenz Julienne)
- fix arm-nommu dma-ranges handling (Vladimir Murzin)
- use __initdata in CMA (Shyam Saini)
- replace the bus dma mask with a limit (Nicolas Saenz Julienne)
- merge the remapping helpers into the main dma-direct flow (me)
- switch xtensa to the generic dma remap handling (me)
- various cleanups around dma_capable (me)
- remove unused dev arguments to various dma-noncoherent helpers (me)
-----BEGIN PGP SIGNATURE-----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=e5wO
-----END PGP SIGNATURE-----
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux; tag 'dma-mapping-5.5' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- improve dma-debug scalability (Eric Dumazet)
- tiny dma-debug cleanup (Dan Carpenter)
- check for vmap memory in dma_map_single (Kees Cook)
- check for dma_addr_t overflows in dma-direct when using DMA offsets
(Nicolas Saenz Julienne)
- switch the x86 sta2x11 SOC to use more generic DMA code (Nicolas
Saenz Julienne)
- fix arm-nommu dma-ranges handling (Vladimir Murzin)
- use __initdata in CMA (Shyam Saini)
- replace the bus dma mask with a limit (Nicolas Saenz Julienne)
- merge the remapping helpers into the main dma-direct flow (me)
- switch xtensa to the generic dma remap handling (me)
- various cleanups around dma_capable (me)
- remove unused dev arguments to various dma-noncoherent helpers (me)
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux:
* tag 'dma-mapping-5.5' of git://git.infradead.org/users/hch/dma-mapping: (22 commits)
dma-mapping: treat dev->bus_dma_mask as a DMA limit
dma-direct: exclude dma_direct_map_resource from the min_low_pfn check
dma-direct: don't check swiotlb=force in dma_direct_map_resource
dma-debug: clean up put_hash_bucket()
powerpc: remove support for NULL dev in __phys_to_dma / __dma_to_phys
dma-direct: avoid a forward declaration for phys_to_dma
dma-direct: unify the dma_capable definitions
dma-mapping: drop the dev argument to arch_sync_dma_for_*
x86/PCI: sta2x11: use default DMA address translation
dma-direct: check for overflows on 32 bit DMA addresses
dma-debug: increase HASH_SIZE
dma-debug: reorder struct dma_debug_entry fields
xtensa: use the generic uncached segment support
dma-mapping: merge the generic remapping helpers into dma-direct
dma-direct: provide mmap and get_sgtable method overrides
dma-direct: remove the dma_handle argument to __dma_direct_alloc_pages
dma-direct: remove __dma_direct_free_pages
usb: core: Remove redundant vmap checks
kernel: dma-contiguous: mark CMA parameters __initdata/__initconst
dma-debug: add a schedule point in debug_dma_dump_mappings()
...
- Protect pci_reassign_bridge_resources() against concurrent
addition/removal (Benjamin Herrenschmidt)
- Fix bridge dma_ranges resource list cleanup (Rob Herring)
- Add PCI_STD_NUM_BARS for the number of standard BARs (Denis Efremov)
- Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters to control the
MMIO and prefetchable MMIO window sizes of hotplug bridges
independently (Nicholas Johnson)
- Fix MMIO/MMIO_PREF window assignment that assigned more space than
desired (Nicholas Johnson)
- Only enforce bus numbers from bridge EA if the bridge has EA devices
downstream (Subbaraya Sundeep)
* pci/resource:
PCI: Do not use bus number zero from EA capability
PCI: Avoid double hpmemsize MMIO window assignment
PCI: Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters
PCI: Add PCI_STD_NUM_BARS for the number of standard BARs
PCI: Fix missing bridge dma_ranges resource list cleanup
PCI: Protect pci_reassign_bridge_resources() against concurrent addition/removal
Here is the big set of USB patches for 5.5-rc1
Lots of little things in here:
- typec updates and additions
- usb-serial drivers cleanups and fixes
- misc USB drivers cleanups and fixes
- gadget drivers new features and controllers added
- usual xhci additions
- other minor changes
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXd5+Iw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylA4wCbB3P206oHeHLBe9Eika3D8gM9/fMAn2oWlmpB
Xh7wr30FGC02zU/KBpJ1
=U5qC
-----END PGP SIGNATURE-----
Merge tag 'usb-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big set of USB patches for 5.5-rc1
Lots of little things in here:
- typec updates and additions
- usb-serial drivers cleanups and fixes
- misc USB drivers cleanups and fixes
- gadget drivers new features and controllers added
- usual xhci additions
- other minor changes
All of these have been in linux-next with no reported issues"
* tag 'usb-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (223 commits)
usb: gadget: udc: gr_udc: create debugfs directory under usb root
usb: gadget: atmel: create debugfs directory under usb root
usb: musb: create debugfs directory under usb root
usb: serial: Fix Kconfig indentation
usb: misc: Fix Kconfig indentation
usb: gadget: Fix Kconfig indentation
usb: host: Fix Kconfig indentation
usb: dwc3: Fix Kconfig indentation
usb: gadget: configfs: Fix missing spin_lock_init()
usb-storage: Disable UAS on JMicron SATA enclosure
USB: documentation: flags on usb-storage versus UAS
USB: uas: heed CAPACITY_HEURISTICS
USB: uas: honor flag to avoid CAPACITY16
usb: host: xhci-tegra: Correct phy enable sequence
usb-serial: cp201x: support Mark-10 digital force gauge
usb: chipidea: imx: pinctrl for HSIC is optional
usb: chipidea: imx: refine the error handling for hsic
usb: chipidea: imx: change hsic power regulator as optional
usb: chipidea: imx: check data->usbmisc_data against NULL before access
usb: chipidea: core: change vbus-regulator as optional
...
Some more development work for v5.5. Highlights include:
- More cleanups from Morimoto-san.
- Trigger word detection for RT5677.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl3bzrQTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0LkMB/4/MkpN4F2WudNCKgmYay2gw3hq8aOR
5Xh/SE6N3BEgBpQiMEUdePRT6LqnQMsSpOaUoKfd4nFvCyLaV7itaYzQuUpo+UJ/
a4UDHJPVfrDJeFghWqSngfEW/N66mpO3UuAvhSRTR3ku0T31v9FkcLsMbdxVUpLC
ablSaFfPCOtTQOsG9blRUL/GAWUhGzPI/Hl4VldS0FvKDmMDY2fxt7QxXRaEYItc
i1Uthklxd0BfRmDqv0WEpduUhbwzg6Uir9pXSisux7DpMk1Li0IyPST5UcRl0Zf4
CKL/qfdQANpufj9kGmrlCOnXB9P5/XYVwfYV430WqMyw0QaOzzSrxT7C
=CZ/+
-----END PGP SIGNATURE-----
Merge tag 'asoc-v5.5-2' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: More updates for v5.5
Some more development work for v5.5. Highlights include:
- More cleanups from Morimoto-san.
- Trigger word detection for RT5677.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now the USB gadget subsystem can use the USB debugfs root directory,
so move it's directory from the root of the debugfs filesystem into
the root of usb
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1574232183-5760-3-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now the USB gadget subsystem can use the USB debugfs root directory,
so move it's directory from the root of the debugfs filesystem into
the root of usb
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1574232183-5760-2-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now the USB gadget subsystem can use the USB debugfs root directory,
so move musb's directory from the root of the debugfs filesystem into
the root of usb
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1574232183-5760-1-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20191121132856.29130-1-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20191121132901.29186-1-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20191121132905.29248-1-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20191121132910.29310-1-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20191121132914.29368-1-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver allocates the spinlock but not initialize it.
Use spin_lock_init() on it to initialize it correctly.
This is detected by Coccinelle semantic patch.
Fixes: 1a1c851bbd ("usb: gadget: configfs: fix concurrent issue between composite APIs")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20191030034046.188808-1-weiyongjun1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Steve Ellis reported incorrect block sizes and alignement
offsets with a SATA enclosure. Adding a quirk to disable
UAS fixes the problems.
Reported-by: Steven Ellis <sellis@redhat.com>
Cc: Pacho Ramos <pachoramos@gmail.com>
Signed-off-by: Laura Abbott <labbott@fedoraproject.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to ignore this flag. We should be as close
to storage in that regard as makes sense, so honor flags whose
cost is tiny.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191114112758.32747-3-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Copy the support over from usb-storage to get feature parity
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191114112758.32747-2-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
XUSB phy needs to be enabled before un-powergating the power partitions.
However in the current sequence, it happens opposite. Correct the phy
enable and powergating partition sequence to avoid any boot hangs.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jui Chang Kuo <jckuo@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/1572859470-7823-1-git-send-email-nkristam@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Improve the HSIC handler for i.mx serial SoC
- Some other tiny changes
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEDaZUZmFxRG/wNThrSFkpgVDWcbsFAl3SaUUACgkQSFkpgVDW
cbvZfggAkTH6DWGrKBMZQaIZEyly8IVLEQ0Tgu0sid/Fjrzgl/xX39gr3uVijuHm
d3tF2iFkyKdxH6nXRHd7CpxdoWtRCU6/kp7H8n8JBQMwZdLJ7DIeFSYYXRkUHbKA
/9iwB0iJo6JJjUrCVeUoa6CLrqUvW2+gN+KqnLHaLKXvFOudNvD9e6iWEdOGHHKF
ihS0YUlCUGe8OrYsPw5Y4fvVN5jCfnkvZB5qVcYxTKwIbuTgTOvZt/9tq0zKVhRv
ZTZTXmjhgFRqPwI5P+4Xyj+fHKQH+gGMhLFy2wO5p1y4vwMsAeYnAUhdlorOhvoC
YGulhJ6/kdnRLHSutfB/uil8IyUTHA==
=M0r2
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
- Improve the Vbus handler
- Improve the HSIC handler for i.mx serial SoC
- Some other tiny changes
* tag 'usb-ci-v5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
usb: chipidea: imx: pinctrl for HSIC is optional
usb: chipidea: imx: refine the error handling for hsic
usb: chipidea: imx: change hsic power regulator as optional
usb: chipidea: imx: check data->usbmisc_data against NULL before access
usb: chipidea: core: change vbus-regulator as optional
usb: chipidea: imx: enable vbus and id wakeup only for OTG events
usb: chipidea: udc: protect usb interrupt enable
usb: chipidea: udc: add new API ci_hdrc_gadget_connect
Add support for the Mark-10 digital force gauge device to the cp201x
driver.
Based on a report and a larger patch from Joel Jennings
Reported-by: Joel Jennings <joel.jennings@makeitlabs.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191118092119.GA153852@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For imx chipidea controllers, if they use mxs PHY, they need pinctrl
for HSIC. Otherwise, it doesn't need pinctrl and usbmisc control. Like
imx7d and imx8mm.
Reported-by: André Draszik <git@andred.net>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
- -EPROBE_DEFER is an error, but without need show error message
- If pintrol is not existed, as pintrol is NULL
Signed-off-by: Peter Chen <peter.chen@nxp.com>
As usbmisc_data is optional, so add the check before access its member,
this fix below static checker warning:
drivers/usb/chipidea/ci_hdrc_imx.c:438 ci_hdrc_imx_probe()
warn: 'data->usbmisc_data' can also be NULL
which is introduced by Patch 15b80f7c3a7f:
"usb: chipidea: imx: enable vbus and id wakeup only for OTG events"
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Vbus regualtor is an optional regulator, for platforms, which
doesn't have this regulator, it will get a dummy regulator and
show warning message.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
If ID or VBUS is from external block, don't enable its wakeup
because it isn't used at all.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
We hit the problem with below sequence:
- ci_udc_vbus_session() update vbus_active flag and ci->driver
is valid,
- before calling the ci_hdrc_gadget_connect(),
usb_gadget_udc_stop() is called by application remove gadget
driver,
- ci_udc_vbus_session() will contine do ci_hdrc_gadget_connect() as
gadget_ready is 1, so udc interrupt is enabled, but ci->driver is
NULL.
- USB connection irq generated but ci->driver is NULL.
As udc irq only should be enabled when gadget driver is binded, so
add spinlock to protect the usb irq enable for vbus session handling.
Signed-off-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
This API is used enable device function, it is called at below
situations:
- VBUS is connected during boots up
- Hot plug occurs during runtime
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Jun Li <jun.li@nxp.com>
We have TI's glue layer for the Cadence USB3 controller going
upstream. Tegra's XUDC driver is also going upstream with this pull
request.
Apart from these two big features, we have a bunch of patches switching
over to devm_platform_ioremap_resource() in order to simplify code a
little; and a non-critical fix for DWC3 usage via kexec.
-----BEGIN PGP SIGNATURE-----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=Xyc8
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: changes for v5.5
We have TI's glue layer for the Cadence USB3 controller going
upstream. Tegra's XUDC driver is also going upstream with this pull
request.
Apart from these two big features, we have a bunch of patches switching
over to devm_platform_ioremap_resource() in order to simplify code a
little; and a non-critical fix for DWC3 usage via kexec.
* tag 'usb-for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (44 commits)
usb: dwc3: of-simple: add a shutdown
usb: cdns3: Add TI specific wrapper driver
dt-bindings: usb: Add binding for the TI wrapper for Cadence USB3 controller
usb: mtu3: fix race condition about delayed_status
usb: gadget: Add UDC driver for tegra XUSB device mode controller
usb: dwc3: debug: Remove newline printout
usb: dwc2: use a longer core rest timeout in dwc2_core_reset()
usb: gadget: udc: lpc32xx: Use devm_platform_ioremap_resource() in lpc32xx_udc_probe()
USB: gadget: udc: clean up an indentation issue
usb: gadget: Quieten gadget config message
phy: renesas: rcar-gen3-usb2: Use platform_get_irq_optional() for optional irq
usb: gadget: Remove set but not used variable 'opts' in msg_do_config
usb: gadget: Remove set but not used variable 'opts' in acm_ms_do_config
usb: mtu3: add a new function to do status stage
usb: gadget: configfs: fix concurrent issue between composite APIs
usb: gadget: f_tcm: Provide support to get alternate setting in tcm function
usb: gadget: Correct NULL pointer checking in fsl gadget
usb: fsl: Remove unused variable
USB: dummy-hcd: use usb_urb_dir_in instead of usb_pipein
USB: dummy-hcd: increase max number of devices to 32
...
All configuration can and should be done through fwnodes instead of
through the tcpc_config struct and there are no existing users left of
struct tcpc_config, so lets remove it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20191114111840.40876-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Ice Lake has two xHCI controllers one on PCH and the other as part
of the CPU itself. The latter is also part of the so called Type C
Subsystem (TCSS) sharing ACPI power resources with the PCIe root ports
and the Thunderbolt controllers. In order to put the whole TCSS block
into D3cold the xHCI needs to be runtime suspended as well when idle.
For this reason allow runtime PM as default for Ice Lake TCSS xHCI
controller.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1573836603-10871-5-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch "USB: HCD: support giveback of URB in tasklet context"[1]
introduced giveback of urb in tasklet context. [1] This patch was
applied to ehci but not xhci. [2] This patch significantly reduces
the hard irq time of xhci. Especially for uvc driver, the hard irq
including the uvc completion function runs quite long but applying
this patch reduces the hard irq time of xhci.
I have tested four SS devices to check if performance degradation
occurs when urb completion functions run in the tasklet context.
As a result of the test, all devices works well and shows very
similar performance with the upstream kernel. Moreover, usb ethernet
adapter show better performance than the upstream kernel about 5% for
RX and 2% for TX. Four SS devices is as follows.
SS devices for test
1. WD My Passport 2TB (external hard drive)
2. Sandisk Ultra Flair USB 3.0 32GB
3. Logitech Brio webcam
4. Iptime 1gigabit ethernet adapter (Mediatek RTL8153)
Test description
1. Mass storage (hard drive) performance test
- run below command 10 times and compute the average performance
dd if=/dev/sdN iflag=direct of=/dev/null bs=1G count=1
2. Mass storage (flash memory) performance test
- run below command 10 times and compute the average performance
dd if=/dev/sdN iflag=direct of=/dev/null bs=1G count=1
3. Webcam streaming performance test
- run simple capture program and get the average frame rate per second
- capture 1500 frames
- program link
https://github.com/asfaca/Webcam-performance-analyzing-tool
- video resolution : 4096 X 2160 (4K) at 30 or 24 fps
- device (Logitech Brio) spec url for the highest resolution and fps
https://support.logitech.com/en_gb/product/brio-stream/specs
4. USB Ethernet adapter performance test
- directly connect two linux machines with ethernet cable
- run pktgen of linux kernel and send 1500 bytes packets
- run vnstat to measure the network bandwidth for 180 seconds
Test machine
- CPU : Intel i5-7600 @ 3.5GHz
Test results
1. Mass storage (hard drive) performance test
WD My Passport 2TB (external hard drive)
--------------------------------------------------------------------
xhci without tasklet | xhci with tasklet
--------------------------------------------------------------------
103.667MB/s | 103.692MB/s
--------------------------------------------------------------------
2. Mass storage (flash memory) performance test
Sandisk Ultra Flair USB 3.0 32GB
--------------------------------------------------------------------
xhci without tasklet | xhci with tasklet
--------------------------------------------------------------------
129.727MB/s | 130.2MB/s
--------------------------------------------------------------------
3. Webcam streaming performance test
Logitech Brio webcam
--------------------------------------------------------------------
xhci without tasklet | xhci with tasklet
--------------------------------------------------------------------
26.4451 fps | 26.3949 fps
--------------------------------------------------------------------
4. USB Ethernet adapter performance test
Iptime 1gigabit ethernet adapter (Mediatek RTL8153)
--------------------------------------------------------------------
xhci without tasklet | xhci with tasklet
--------------------------------------------------------------------
RX 933.86 Mbit/s | 983.86 Mbit/s
--------------------------------------------------------------------
TX 830.18 Mbit/s | 882.75 Mbit/s
--------------------------------------------------------------------
[1], https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=94dfd7edfd5c9b605caf7b562de7a813d216e011
[2], https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=428aac8a81058e2303677a8fbf26670229e51d3a
Signed-off-by: Suwan Kim <suwan.kim027@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1573836603-10871-4-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trace when a register in the doorbell array is written,
both for host controller command doorbell and device doorbells,
including for which endpoint and stream
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1573836603-10871-3-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some situations, the software handles TRB events slower
than adding TRBs, then xhci_handle_event can't return zero
long time, the xHC will consider the event ring is full,
and trigger "Event Ring Full" error, but in fact, the software
has already finished lots of events, just no chance to
update ERDP (event ring dequeue pointer).
In this commit, we force update ERDP if half of TRBS_PER_SEGMENT
events have handled to avoid "Event Ring Full" error.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1573836603-10871-2-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the USB-serial updates for 5.5-rc1, including:
- support for a new class of pl2303 devices
- improved divisor calculations for ch341
- fixes for a remote-wakeup bug in the moschip drivers
- improved device-type handling in mos7840
- various cleanups of mos7840
Included are also some new device ids.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXc52mwAKCRALxc3C7H1l
CDKaAQCZonIg8g1Wu3wdZmTOg4jmL2tiur3sp8oWKYFgKld3iQEAi6pTSKdrVYHf
FviCzUi1UnZGjtZYyj1h8NqiAS8vJA0=
=33aM
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.5-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 5.5-rc1
Here are the USB-serial updates for 5.5-rc1, including:
- support for a new class of pl2303 devices
- improved divisor calculations for ch341
- fixes for a remote-wakeup bug in the moschip drivers
- improved device-type handling in mos7840
- various cleanups of mos7840
Included are also some new device ids.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-5.5-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: ftdi_sio: add device IDs for U-Blox C099-F9P
USB: serial: option: add support for Foxconn T77W968 LTE modules
USB: serial: mos7840: drop port open flag
USB: serial: mos7840: drop read-urb check
USB: serial: mos7840: drop port driver data accessors
USB: serial: mos7840: drop serial struct accessor
USB: serial: mos7840: drop paranoid serial checks
USB: serial: mos7840: drop paranoid port checks
USB: serial: mos7840: drop redundant urb context check
USB: serial: mos7840: rip out broken interrupt handling
USB: serial: mos7840: fix probe error handling
USB: serial: mos7840: document MCS7810 detection hack
USB: serial: mos7840: clean up device-type handling
USB: serial: mos7840: fix remote wakeup
USB: serial: mos7720: fix remote wakeup
USB: serial: option: add support for DW5821e with eSIM support
USB: serial: mos7840: add USB ID to support Moxa UPort 2210
USB: serial: ch341: reimplement line-speed handling
USB: serial: pl2303: add support for PL2303HXN
This device presents itself as a USB hub with three attached devices:
- An ACM serial port connected to the GPS module (not affected by this
commit)
- An FTDI serial port connected to the GPS module (1546:0502)
- Another FTDI serial port connected to the ODIN-W2 radio module
(1546:0503)
This commit registers U-Blox's VID and the PIDs of the second and third
devices.
Datasheet: https://www.u-blox.com/sites/default/files/C099-F9P-AppBoard-Mbed-OS3-FW_UserGuide_%28UBX-18063024%29.pdf
Signed-off-by: Fabio D'Urso <fabiodurso@hotmail.it>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Now the USB gadget subsystem can use the USB debugfs root directory,
so move it's directory from the root of the debugfs filesystem into
the root of usb
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1573541519-28488-13-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now the USB gadget subsystem can use the USB debugfs root directory,
so move it's directory from the root of the debugfs filesystem into
the root of usb
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1573541519-28488-11-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now the USB gadget subsystem can use the USB debugfs root directory,
so move it's directory from the root of the debugfs filesystem into
the root of usb
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1573541519-28488-10-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now the USB gadget subsystem can use the USB debugfs root directory,
so move it's directory from the root of the debugfs filesystem into
the root of usb
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1573541519-28488-8-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now the USB gadget subsystem can use the USB debugfs root directory,
so move dwc2's directory from the root of the debugfs filesystem into
the root of usb
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1573541519-28488-7-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now the USB gadget subsystem can use the USB debugfs root directory,
so move dsps's directory from the root of the debugfs filesystem into
the root of usb
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1573541519-28488-6-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now the USB gadget subsystem can use the USB debugfs root directory,
so move dwc3's directory from the root of the debugfs filesystem into
the root of usb
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1573541519-28488-4-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Smatch reported that nents is not initialized and used in
stub_recv_cmd_submit(). nents is currently initialized by sgl_alloc()
and used to allocate multiple URBs when host controller doesn't
support scatter-gather DMA. The use of uninitialized nents means that
buf_len is zero and use_sg is true. But buffer length should not be
zero when an URB uses scatter-gather DMA.
To prevent this situation, add the conditional that checks buf_len
and use_sg. And move the use of nents right after the sgl_alloc() to
avoid the use of uninitialized nents.
If the error occurs, it adds SDEV_EVENT_ERROR_MALLOC and stub_priv
will be released by stub event handler and connection will be shut
down.
Fixes: ea44d19076 ("usbip: Implement SG support to vhci-hcd and stub driver")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Suwan Kim <suwan.kim027@gmail.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191111141035.27788-1-suwan.kim027@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove SG_NONE and a related misleading comment. Update documentation.
This patch does not affect behaviour as zero initialization is redundant.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Viresh Kumar <vireshk@kernel.org>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: usb-storage@lists.one-eyed-alien.net
Link: https://lore.kernel.org/r/b4779b7a6563f6bd8d259ee457871c1c463c420e.1572656814.git.fthain@telegraphics.com.au
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Drop the redundant port open flag and corresponding checks. USB serial
core will not call any of these driver callbacks for a closed port, and the
write URBs are stopped at close().
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop read-urb check which is always false from completion the callback.
The driver read-urb pointer is set at every open and is never cleared.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop the custom port driver data accessors and paranoid sanity checks.
The driver data is not cleared until the driver is unbound.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop the helper used to retrieve the serial struct pointer from the port
structure.
Note that this helper was only used when the serial structure was
actually not needed.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop the likewise paranoid serial structure sanity checks.
USB serial core sets the serial pointer in the port structures at
initialisation and it is never cleared, and similar for the serial
structure type.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop the paranoid port structure sanity checks which are confusing at
best.
The driver data port pointer is set at port probe and never cleared,
while USB serial core sets the tty driver data at install and won't call
any driver functions with a NULL port pointer.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The bulk-in URB context is set to the driver-data struct at open and is
never cleared so drop the redundant check in the completion callback.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The interrupt handling is completely broken and has in fact never been
been enabled due to an inverted test for an interrupt endpoint in
open() that prevented the interrupt URB from being submitted.
Other highlights include missing interrupt URB resubmission (had it
ever been submitted), missing locking when managing the open-port count,
and NULL-pointer dereferences that could have been triggered by a
malicious device.
Rip out this broken crap which is beyond repair instead of pretending
we support this feature.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The driver would return success and leave the port structures
half-initialised if any of the register accesses during probe fails.
This would specifically leave the port control urb unallocated,
something which could trigger a NULL pointer dereference on interrupt
events.
Fortunately the interrupt implementation is completely broken and has
never even been enabled...
Note that the zero-length-enable register write used to set the zle-flag
for all ports is moved to attach.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Document the MCS7810 detection hack which relies on having the GPO and
GPI pins connected as recommended by ASIX.
Note that GPO (pin 42) is really RTS of the third port which will be
toggled for the corresponding physical port on two- and four-port
devices.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The current device-type detection is fragile and can't really be relied
upon. Instead of sprinkling device-id conditionals throughout the
driver, let's use the device-id table to encode the number of ports and
whether the device has a driver-controlled activity LED (MCS7810).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The driver was setting the device remote-wakeup feature during probe in
violation of the USB specification (which says it should only be set
just prior to suspending the device). This could potentially waste
power during suspend as well as lead to spurious wakeups.
Note that USB core would clear the remote-wakeup feature at first
resume.
Fixes: 3f5429746d ("USB: Moschip 7840 USB-Serial Driver")
Cc: stable <stable@vger.kernel.org> # 2.6.19
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The driver was setting the device remote-wakeup feature during probe in
violation of the USB specification (which says it should only be set
just prior to suspending the device). This could potentially waste
power during suspend as well as lead to spurious wakeups.
Note that USB core would clear the remote-wakeup feature at first
resume.
Fixes: 0f64478cbc ("USB: add USB serial mos7720 driver")
Cc: stable <stable@vger.kernel.org> # 2.6.19
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
In case of a timeout or if a signal aborts a read
communication with the device needs to be ended
lest we overwrite an active URB the next time we
do IO to the device, as the URB may still be active.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191107142856.16774-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The recent change (commit 08422d2c55: "ALSA: memalloc: Allow NULL
device for SNDRV_DMA_TYPE_CONTINUOUS type") made the PCM preallocation
helper accepting NULL as the device pointer for the default usage.
Drop the snd_dma_continuous_data() usage that became superfluous from
the callers.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20191108164214.611-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
struct scsi_cmnd cmd->req.resid_len which is returned and set respectively
by the helper functions scsi_get_resid() and scsi_set_resid() is an
unsigned int. Reflect this fact in the interface of these helper functions.
Also fix compilation errors due to min() and max() type mismatch introduced
by this change in scsi debug code, usb transport code and in the USB ENE
card reader driver.
Link: https://lore.kernel.org/r/20191030090847.25650-1-damien.lemoal@wdc.com
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The work item can operate on
1. stale memory left over from the last transfer
the actual length of the data transfered needs to be checked
2. memory already freed
the error handling in appledisplay_probe() needs
to cancel the work in that case
Reported-and-tested-by: syzbot+495dab1f175edc9c2f13@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191106124902.7765-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop some superfluous newlines before conditionals which made the code
harder to read.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191105084152.16322-15-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop superfluous brackets around single-line blocks.
Also add missing white space around operators in a for-expression being
modified.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191105084152.16322-14-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop space between function identifiers and opening parenthesis, which
was no longer even used consistently within the driver.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191105084152.16322-13-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The endianness is already encoded in the type specifier so drop the
redundant little-endian comments from the message structs.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191105084152.16322-12-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the packed attributes from the two message structs whose fields
are naturally aligned and do not have any padding.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191105084152.16322-11-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up the pointer declarations in the driver data, whose style wasn't
even consistent with the rest of the driver.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191105084152.16322-10-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the tower_abort_transfers() function which is now only called from
release and instead explicitly kill the two URBs.
This incidentally also fixes the outdated comment about freeing memory.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191105084152.16322-9-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stop also the interrupt-out URB unconditionally in
tower_abort_transfers() which is called from release() (for connected
devices). Calling usb_kill_urb() for an idle URB is perfectly fine.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191105084152.16322-8-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the redundant interrupt-in-running flag, which tried to keep track
of when the interrupt-in URB was in flight. This isn't needed since we
can stop the URB unconditionally in tower_abort_transfers() and the URB
can not be submitted while usb_kill_urb() is running anyway.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191105084152.16322-7-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
User space already sees -ENODEV in case it tries to do I/O post
disconnect, no need to spam the logs with printk messages that don't
even include any device-id information.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191105084152.16322-6-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop redundant open_count check in release; the open count is used as a
flag and is only set to 0 or 1.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191105084152.16322-5-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Zero the driver data at allocation rather than depend on explicit
zeroing, which easy to miss.
Also drop an unnecessary driver-data pointer initialisation.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191105084152.16322-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop redundant NULL check from tower_abort_transfers(), which is never
called with a NULL argument.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191105084152.16322-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MODULE_LICENSE macro is unconditionally defined in module.h, no need
to ifdef its use.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191105084152.16322-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop space between function identifiers and opening parenthesis, which
was no longer even used consistently within the driver.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191105103638.4929-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The open count will always be exactly one when release is called, so
drop the redundant sanity check.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191105103638.4929-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit d4ead16f50 ("USB: prevent char device open/deregister
race") core prevents further calls to open() after usb_deregister_dev()
returns so there's no need to use the interface data for
synchronisation.
This effectively reverts commit 54d2bc068f ("USB: fix locking in
idmouse") with respect to the open-disconnect race.
Note that the driver already uses a present flag to suppress I/O post
disconnect (even if all USB I/O take place at open).
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191105103638.4929-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Dell WD15 dock, sometimes USB ethernet cannot be detected after plugging
cable to the ethernet port, the hub and roothub get runtime resumed and
runtime suspended immediately:
...
[ 433.315169] xhci_hcd 0000:3a:00.0: hcd_pci_runtime_resume: 0
[ 433.315204] usb usb4: usb auto-resume
[ 433.315226] hub 4-0:1.0: hub_resume
[ 433.315239] xhci_hcd 0000:3a:00.0: Get port status 4-1 read: 0x10202e2, return 0x10343
[ 433.315264] usb usb4-port1: status 0343 change 0001
[ 433.315279] xhci_hcd 0000:3a:00.0: clear port1 connect change, portsc: 0x10002e2
[ 433.315293] xhci_hcd 0000:3a:00.0: Get port status 4-2 read: 0x2a0, return 0x2a0
[ 433.317012] xhci_hcd 0000:3a:00.0: xhci_hub_status_data: stopping port polling.
[ 433.422282] xhci_hcd 0000:3a:00.0: Get port status 4-1 read: 0x10002e2, return 0x343
[ 433.422307] usb usb4-port1: do warm reset
[ 433.422311] usb 4-1: device reset not allowed in state 8
[ 433.422339] hub 4-0:1.0: state 7 ports 2 chg 0002 evt 0000
[ 433.422346] xhci_hcd 0000:3a:00.0: Get port status 4-1 read: 0x10002e2, return 0x343
[ 433.422356] usb usb4-port1: do warm reset
[ 433.422358] usb 4-1: device reset not allowed in state 8
[ 433.422428] xhci_hcd 0000:3a:00.0: set port remote wake mask, actual port 0 status = 0xf0002e2
[ 433.422455] xhci_hcd 0000:3a:00.0: set port remote wake mask, actual port 1 status = 0xe0002a0
[ 433.422465] hub 4-0:1.0: hub_suspend
[ 433.422475] usb usb4: bus auto-suspend, wakeup 1
[ 433.426161] xhci_hcd 0000:3a:00.0: xhci_hub_status_data: stopping port polling.
[ 433.466209] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[ 433.510204] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[ 433.554051] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[ 433.598235] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[ 433.642154] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[ 433.686204] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[ 433.730205] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[ 433.774203] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[ 433.818207] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[ 433.862040] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[ 433.862053] xhci_hcd 0000:3a:00.0: xhci_hub_status_data: stopping port polling.
[ 433.862077] xhci_hcd 0000:3a:00.0: xhci_suspend: stopping port polling.
[ 433.862096] xhci_hcd 0000:3a:00.0: // Setting command ring address to 0x8578fc001
[ 433.862312] xhci_hcd 0000:3a:00.0: hcd_pci_runtime_suspend: 0
[ 433.862445] xhci_hcd 0000:3a:00.0: PME# enabled
[ 433.902376] xhci_hcd 0000:3a:00.0: restoring config space at offset 0xc (was 0x0, writing 0x20)
[ 433.902395] xhci_hcd 0000:3a:00.0: restoring config space at offset 0x4 (was 0x100000, writing 0x100403)
[ 433.902490] xhci_hcd 0000:3a:00.0: PME# disabled
[ 433.902504] xhci_hcd 0000:3a:00.0: enabling bus mastering
[ 433.902547] xhci_hcd 0000:3a:00.0: // Setting command ring address to 0x8578fc001
[ 433.902649] pcieport 0000:00:1b.0: PME: Spurious native interrupt!
[ 433.902839] xhci_hcd 0000:3a:00.0: Port change event, 4-1, id 3, portsc: 0xb0202e2
[ 433.902842] xhci_hcd 0000:3a:00.0: resume root hub
[ 433.902845] xhci_hcd 0000:3a:00.0: handle_port_status: starting port polling.
[ 433.902877] xhci_hcd 0000:3a:00.0: xhci_resume: starting port polling.
[ 433.902889] xhci_hcd 0000:3a:00.0: xhci_hub_status_data: stopping port polling.
[ 433.902891] xhci_hcd 0000:3a:00.0: hcd_pci_runtime_resume: 0
[ 433.902919] usb usb4: usb wakeup-resume
[ 433.902942] usb usb4: usb auto-resume
[ 433.902966] hub 4-0:1.0: hub_resume
...
As Mathias pointed out, the hub enters Cold Attach Status state and
requires a warm reset. However usb_reset_device() bails out early when
the device is in suspended state, as its callers port_event() and
hub_event() don't always resume the device.
Since there's nothing wrong to reset a suspended device, allow
usb_reset_device() to do so to solve the issue.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191106062710.29880-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove pointer dereference after free.
pci_pool_free doesn't care about contents of td.
It's just a void* for it
Addresses-Coverity-ID: 1091173 ("Use after free")
Cc: stable@vger.kernel.org
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20191106202821.GA20347@embeddedor
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add USB ID for MOXA UPort 2210. This device contains mos7820 but
it passes GPIO0 check implemented by driver and it's detected as
mos7840. Hence product id check is added to force mos7820 mode.
Signed-off-by: Pavel Löbl <pavel@loebl.cz>
Cc: stable <stable@vger.kernel.org>
[ johan: rename id defines and add vendor-id check ]
Signed-off-by: Johan Hovold <johan@kernel.org>
There is no need to reset the PPM when the interface is
unregistered. Quietly silencing the notifications and then
unregistering everything is enough. This speeds up
ucsi_unregister() a lot.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Ajay Gupta <ajayg@nvidia.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20191104142435.29960-19-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding new error codes to the driver that were introduced in
UCSI specification v1.1.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Ajay Gupta <ajayg@nvidia.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20191104142435.29960-18-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can't use bit fields with data that is received or send
to/from the device.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Ajay Gupta <ajayg@nvidia.com>
Link: https://lore.kernel.org/r/20191104142435.29960-17-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
That data structure was used for constructing the commands
before executing them, but it was never really useful. Using
the structure just complicated the driver. The commands are
64-bit wide, so it is enough to simply fill a u64 variable.
No data structures needed.
This simplifies the driver considerable and makes it much
easier to for example add support for big endian systems
later on.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Ajay Gupta <ajayg@nvidia.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20191104142435.29960-16-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The drivers now only use the new API, so removing the old one.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Ajay Gupta <ajayg@nvidia.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20191104142435.29960-15-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replacing the old "cmd" and "sync" callbacks with an
implementation of struct ucsi_operations. The interrupt
handler will from now on read the CCI (Command Status and
Connector Change Indication) register, and call
ucsi_connector_change() function and/or complete pending
command completions based on it.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Ajay Gupta <ajayg@nvidia.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20191104142435.29960-14-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replacing the old "cmd" and "sync" callbacks with an
implementation of struct ucsi_operations. The ACPI
notification (interrupt) handler will from now on read the
CCI (Command Status and Connector Change Indication)
register, and call ucsi_connector_change() function and/or
complete pending command completions based on it.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20191104142435.29960-13-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding more simplified API for interface registration and
read and write operations.
The registration is split into separate creation and
registration phases. That allows the drivers to properly
initialize the interface before registering it if necessary.
The read and write operations are supplied in a completely
separate struct ucsi_operations that is passed to the
ucsi_register() function during registration. The new read
and write operations will work more traditionally so that
the read callback function reads a requested amount of data
from an offset, and the write callback functions write the
given data to the offset. The drivers will have to support
both non-blocking writing and blocking writing. In blocking
writing the driver itself is responsible of waiting for the
completion event.
The new API makes it possible for the drivers to perform
tasks also independently of the core ucsi.c, and that should
allow for example quirks to be handled completely in the
drivers without the need to touch ucsi.c.
The old API is kept until all drivers have been converted to
the new API.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Ajay Gupta <ajayg@nvidia.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20191104142435.29960-12-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver already finds the node in order to get reference
to the USB role switch.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20191104142435.29960-11-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Supplying the operation callbacks as part of a struct
typec_operations instead of as part of struct
typec_capability during port registration. After this there
is not need to keep the capabilities stored anywhere in the
driver.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20191104142435.29960-8-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Supplying the operation callbacks as part of a struct
typec_operations instead of as part of struct
typec_capability during port registration.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20191104142435.29960-7-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Supplying the operation callbacks as part of a struct
typec_operations instead of as part of struct
typec_capability during port registration. After this there
is not need to keep the capabilities stored anywhere in the
driver.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20191104142435.29960-6-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Supplying the operation callbacks as part of a struct
typec_operations instead of as part of struct
typec_capability during port registration.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20191104142435.29960-5-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introducing struct typec_operations which has the same
callbacks as struct typec_capability. The old callbacks are
kept for now, but after all users have been converted, they
will be removed.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20191104142435.29960-4-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Leaving the private driver_data pointer of the port device
to the port drivers.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20191104142435.29960-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Copying everything from struct typec_capability to struct
typec_port during port registration. This will make sure
that under no circumstances the driver can change the values
in the struct typec_capability that the port uses.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20191104142435.29960-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit fea3409112 ("USB: add direction bit to urb->transfer_flags") has
added a usb_urb_dir_in() helper function that can be used to determine
the direction of the URB. With that patch USB_DIR_IN control requests with
wLength == 0 are considered out requests by real USB HCDs. This patch
changes dummy-hcd to use the usb_urb_dir_in() helper to match that
behavior.
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Link: https://lore.kernel.org/r/4ae9e68ebca02f08a93ac61fe065057c9a01f0a8.1571667489.git.andreyknvl@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When fuzzing the USB subsystem with syzkaller, we currently use 8 testing
processes within one VM. To isolate testing processes from one another it
is desirable to assign a dedicated USB bus to each of those, which means
we need at least 8 Dummy UDC/HCD devices.
This patch increases the maximum number of Dummy UDC/HCD devices to 32
(more than 8 in case we need more of them in the future).
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Link: https://lore.kernel.org/r/665578f904484069bb6100fb20283b22a046ad9b.1571667489.git.andreyknvl@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver forgets to call clk_put when probe fails and remove.
Add the calls to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191102062245.4014-1-hslester96@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB2422 uses a different package that the USB251x and only comes in
a variant with 2 downstream ports. Other than that it is software
compatible.
Tested-by: Carsten Stelling <carsten.stelling@goerlitz.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20191023105250.16537-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The five removed symbols are unused since they were introduced in commit
3ec72a2a1e ("usb: misc: add USB251xB/xBi Hi-Speed Hub Controller
Driver") back in 2017.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20191023105250.16537-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a number of places in the driver where it fails
to maintain __iomem on pointers used to access registers
so fixup the warnings by adding these in the appropriate
places.
Examples of the sparse warnings fixed:
drivers/usb/host/oxu210hp-hcd.c:686:9: warning: incorrect type in argument 2 (different address spaces)
drivers/usb/host/oxu210hp-hcd.c:686:9: expected void volatile [noderef] <asn:2> *addr
drivers/usb/host/oxu210hp-hcd.c:686:9: got void *
drivers/usb/host/oxu210hp-hcd.c:686:9: warning: incorrect type in argument 2 (different address spaces)
drivers/usb/host/oxu210hp-hcd.c:686:9: expected void volatile [noderef] <asn:2> *addr
drivers/usb/host/oxu210hp-hcd.c:686:9: got void *
drivers/usb/host/oxu210hp-hcd.c:686:9: warning: incorrect type in argument 2 (different address spaces)
drivers/usb/host/oxu210hp-hcd.c:686:9: expected void volatile [noderef] <asn:2> *addr
drivers/usb/host/oxu210hp-hcd.c:686:9: got void *
drivers/usb/host/oxu210hp-hcd.c:681:16: warning: incorrect type in argument 1 (different address spaces)
drivers/usb/host/oxu210hp-hcd.c:681:16: expected void const volatile [noderef] <asn:2> *addr
drivers/usb/host/oxu210hp-hcd.c:681:16: got void *
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Link: https://lore.kernel.org/r/20191017171934.8771-1-ben.dooks@codethink.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bcma_hcd_probe misses a check for devm_gpiod_get and may miss
the error.
Add a check for it and return the error if a failure occurs.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191016083531.5734-1-hslester96@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hcd pointer in ohci_hcd_nxp_probe() is
being initialised with a 0, so fix to NULL to
avoid the following sparse warning:
drivers/usb/host/ohci-nxp.c:153:31: warning: Using plain integer as NULL pointer
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Link: https://lore.kernel.org/r/20191015141945.16067-1-ben.dooks@codethink.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simple wrapper function that searches USB role switches with
class_find_device_by_fwnode().
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20191008122600.22340-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current ch341 divisor algorithm was known to give inaccurate results
for certain higher line speeds. Jonathan Olds <jontio@i4free.co.nz>
investigated this, determined the basic equations used to derive the
divisors and confirmed them experimentally [1].
The equations Jonathan used could be generalised further to:
baudrate = 48000000 / (2^(12 - 3 * ps - fact) * div), where
0 <= ps <= 3,
0 <= fact <= 1,
2 <= div <= 256 if fact = 0, or
9 <= div <= 256 if fact = 1
which will also give better results for lower rates.
Notably the error is reduced for the following standard rates:
1152000 (4.0% instead of 15% error)
921600 (0.16% instead of -7.5% error)
576000 (-0.80% instead of -5.6% error)
200 (0.16% instead of -0.69% error)
134 (-0.05% instead of -0.63% error)
110 (0.03% instead of -0.44% error)
but also for many non-standard ones.
The current algorithm also suffered from rounding issues (e.g.
requesting 2950000 Bd resulted in a rate of 2 MBd instead of 3 MBd and
thus a -32% instead of 1.7% error).
The new algorithm was inspired by the current vendor driver even if that
one only handles two higher rates that require fact=1 by hard coding the
corresponding divisors [2].
Michael Dreher <michael@5dot1.de> also did a similar generalisation of
Jonathan's work and has published his results with a very good summary
that provides further insights into how this device works [3].
[1] https://lkml.kernel.org/r/000001d51f34$bad6afd0$30840f70$@co.nz
[2] http://www.wch.cn/download/CH341SER_LINUX_ZIP.html
[3] https://github.com/nospam2000/ch341-baudrate-calculation
Reported-by: Jonathan Olds <jontio@i4free.co.nz>
Tested-by: Jonathan Olds <jontio@i4free.co.nz>
Cc: Michael Dreher <michael@5dot1.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
When disabling an endpoint which has cancelled requests, we should
make sure to giveback requests that are currently pending in the
cancelled list, otherwise we may fall into a situation where command
completion interrupt fires after endpoint has been disabled, therefore
causing a splat.
Fixes: fec9095bde "usb: dwc3: gadget: remove wait_end_transfer"
Reported-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Link: https://lore.kernel.org/r/20191031090713.1452818-1-felipe.balbi@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the vmap area checks are being performed in the DMA
infrastructure directly, there is no need to repeat them in USB.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
EP_CLAIMED flag is used to track the claimed endpoints. While unloading the
module, Reset EP_CLAIMED flag for all enabled endpoints. So that it can be
reused.
Signed-off-by: Sanket Parmar <sparmar@cadence.com>
Acked-by: Peter Chen <peter.chen@nxp.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/20191029122441.5816-1-sparmar@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing endianness conversion when setting the line speed so that
this driver might work also on big-endian machines.
Also use an unsigned format specifier in the corresponding debug
message.
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191029102354.2733-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a user-controlled slab buffer overflow due to a missing sanity check
on the bulk-out transfer buffer used for control requests.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191029102354.2733-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case we're loading a new kernel via kexec, let's make sure to
cleanup the dwc3 address space correctly. This means that we should
run the same steps from driver remove, so just extract a reusable
function for both cases.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The J721e platform comes with 2 Cadence USB3 controller
instances. This driver supports the TI specific wrapper
on this platform.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Endpoints with a maxpacket length of 0 are probably useless. They
can't transfer any data, and it's not at all unlikely that a UDC will
crash or hang when trying to handle a non-zero-length usb_request for
such an endpoint. Indeed, dummy-hcd gets a divide error when trying
to calculate the remainder of a transfer length by the maxpacket
value, as discovered by the syzbot fuzzer.
Currently the gadget core does not check for endpoints having a
maxpacket value of 0. This patch adds a check to usb_ep_enable(),
preventing such endpoints from being used.
As far as I know, none of the gadget drivers in the kernel tries to
create an endpoint with maxpacket = 0, but until now there has been
nothing to prevent userspace programs under gadgetfs or configfs from
doing it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+8ab8bf161038a8768553@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1910281052370.1485-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 3ae62a4209 ("UAS: fix alignment of scatter/gather segments"),
copying a similar commit for usb-storage, attempted to solve a problem
involving scatter-gather I/O and USB/IP by setting the
virt_boundary_mask for mass-storage devices.
However, it now turns out that the analogous change in usb-storage
interacted badly with commit 09324d32d2 ("block: force an unlimited
segment size on queues with a virt boundary"), which was added later.
A typical error message is:
ehci-pci 0000:00:13.2: swiotlb buffer is full (sz: 327680 bytes),
total 32768 (slots), used 97 (slots)
There is no longer any reason to keep the virt_boundary_mask setting
in the uas driver. It was needed in the first place only for
handling devices with a block size smaller than the maxpacket size and
where the host controller was not capable of fully general
scatter-gather operation (that is, able to merge two SG segments into
a single USB packet). But:
High-speed or slower connections never use a bulk maxpacket
value larger than 512;
The SCSI layer does not handle block devices with a block size
smaller than 512 bytes;
All the host controllers capable of SuperSpeed operation can
handle fully general SG;
Since commit ea44d19076 ("usbip: Implement SG support to
vhci-hcd and stub driver") was merged, the USB/IP driver can
also handle SG.
Therefore all supported device/controller combinations should be okay
with no need for any special virt_boundary_mask. So in order to head
off potential problems similar to those affecting usb-storage, this
patch reverts commit 3ae62a4209.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Oliver Neukum <oneukum@suse.com>
CC: <stable@vger.kernel.org>
Acked-by: Christoph Hellwig <hch@lst.de>
Fixes: 3ae62a4209 ("UAS: fix alignment of scatter/gather segments")
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1910231132470.1878-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 747668dbc0 ("usb-storage: Set virt_boundary_mask to avoid SG
overflows") attempted to solve a problem involving scatter-gather I/O
and USB/IP by setting the virt_boundary_mask for mass-storage devices.
However, it now turns out that this interacts badly with commit
09324d32d2 ("block: force an unlimited segment size on queues with a
virt boundary"), which was added later. A typical error message is:
ehci-pci 0000:00:13.2: swiotlb buffer is full (sz: 327680 bytes),
total 32768 (slots), used 97 (slots)
There is no longer any reason to keep the virt_boundary_mask setting
for usb-storage. It was needed in the first place only for handling
devices with a block size smaller than the maxpacket size and where
the host controller was not capable of fully general scatter-gather
operation (that is, able to merge two SG segments into a single USB
packet). But:
High-speed or slower connections never use a bulk maxpacket
value larger than 512;
The SCSI layer does not handle block devices with a block size
smaller than 512 bytes;
All the host controllers capable of SuperSpeed operation can
handle fully general SG;
Since commit ea44d19076 ("usbip: Implement SG support to
vhci-hcd and stub driver") was merged, the USB/IP driver can
also handle SG.
Therefore all supported device/controller combinations should be okay
with no need for any special virt_boundary_mask. So in order to fix
the swiotlb problem, this patch reverts commit 747668dbc0.
Reported-and-tested-by: Piergiorgio Sartor <piergiorgio.sartor@nexgo.de>
Link: https://marc.info/?l=linux-usb&m=157134199501202&w=2
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Seth Bollinger <Seth.Bollinger@digi.com>
CC: <stable@vger.kernel.org>
Fixes: 747668dbc0 ("usb-storage: Set virt_boundary_mask to avoid SG overflows")
Acked-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1910211145520.1673-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
iso_buffer should be set to NULL after use and free in the while loop.
In the case of isochronous URB in the while loop, iso_buffer is
allocated and after sending it to server, buffer is deallocated. And
then, if the next URB in the while loop is not a isochronous pipe,
iso_buffer still holds the previously deallocated buffer address and
kfree tries to free wrong buffer address.
Fixes: ea44d19076 ("usbip: Implement SG support to vhci-hcd and stub driver")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Suwan Kim <suwan.kim027@gmail.com>
Reviewed-by: Julia Lawall <julia.lawall@lip6.fr>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20191022093017.8027-1-suwan.kim027@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It looks like some of the xhci debug code is passing u32 to functions
directly from __le32/__le64 fields.
Fix this by using le{32,64}_to_cpu() on these to fix the following
sparse warnings;
xhci-debugfs.c:205:62: warning: incorrect type in argument 1 (different base types)
xhci-debugfs.c:205:62: expected unsigned int [usertype] field0
xhci-debugfs.c:205:62: got restricted __le32
xhci-debugfs.c:206:62: warning: incorrect type in argument 2 (different base types)
xhci-debugfs.c:206:62: expected unsigned int [usertype] field1
xhci-debugfs.c:206:62: got restricted __le32
...
[Trim down commit message, sparse warnings were similar -Mathias]
Cc: <stable@vger.kernel.org> # 4.15+
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1572013829-14044-4-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The arguments to queue_trb are always byteswapped to LE for placement in
the ring, but this should not happen in the case of immediate data; the
bytes copied out of transfer_buffer are already in the correct order.
Add a complementary byteswap so the bytes end up in the ring correctly.
This was observed on BE ppc64 with a "Texas Instruments TUSB73x0
SuperSpeed USB 3.0 xHCI Host Controller [104c:8241]" as a ch341
usb-serial adapter ("1a86:7523 QinHeng Electronics HL-340 USB-Serial
adapter") always transmitting the same character (generally NUL) over
the serial link regardless of the key pressed.
Cc: <stable@vger.kernel.org> # 5.2+
Fixes: 33e39350eb ("usb: xhci: add Immediate Data Transfer support")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1572013829-14044-3-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef513be0a9 ("usb: xhci: Add Clear_TT_Buffer") schedules work
to clear TT buffer, but causes a use-after-free regression at the same time
Make sure hub_tt_work finishes before endpoint is disabled, otherwise
the work will dereference already freed endpoint and device related
pointers.
This was triggered when usb core failed to read the configuration
descriptor of a FS/LS device during enumeration.
xhci driver queued clear_tt_work while usb core freed and reallocated
a new device for the next enumeration attempt.
EHCI driver implents ehci_endpoint_disable() that makes sure
clear_tt_work has finished before it returns, but xhci lacks this support.
usb core will call hcd->driver->endpoint_disable() callback before
disabling endpoints, so we want this in xhci as well.
The added xhci_endpoint_disable() is based on ehci_endpoint_disable()
Fixes: ef513be0a9 ("usb: xhci: Add Clear_TT_Buffer")
Cc: <stable@vger.kernel.org> # v5.3
Reported-by: Johan Hovold <johan@kernel.org>
Suggested-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
Tested-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1572013829-14044-2-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A recent info-leak bug manifested itself along with warning about a
negative buffer overflow:
ldusb 1-1:0.28: Read buffer overflow, -131383859965943 bytes dropped
when it was really a rather large positive one.
A sanity check that prevents this has now been put in place, but let's
fix up the size format specifiers, which should all be unsigned.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191022143203.5260-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The custom ring-buffer implementation was merged without any locking or
explicit memory barriers, but a spinlock was later added by commit
9d33efd9a7 ("USB: ldusb bugfix").
The lock did not cover the update of the tail index once the entry had
been processed, something which could lead to memory corruption on
weakly ordered architectures or due to compiler optimisations.
Specifically, a completion handler running on another CPU might observe
the incremented tail index and update the entry before ld_usb_read() is
done with it.
Fixes: 2824bd250f ("[PATCH] USB: add ldusb driver")
Fixes: 9d33efd9a7 ("USB: ldusb bugfix")
Cc: stable <stable@vger.kernel.org> # 2.6.13
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191022143203.5260-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Endpoints with a maxpacket length of 0 are probably useless. They
can't transfer any data, and it's not at all unlikely that an HCD will
crash or hang when trying to handle an URB for such an endpoint.
Currently the USB core does not check for endpoints having a maxpacket
value of 0. This patch adds a check, printing a warning and skipping
over any endpoints it catches.
Now, the USB spec does not rule out endpoints having maxpacket = 0.
But since they wouldn't have any practical use, there doesn't seem to
be any good reason for us to accept them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1910281050420.1485-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB gadget core is supposed to manage pullups
of the controller. Don't manage pullups from within
the controller driver. Otherwise, function drivers
are not able to keep the controller disconnected from
the bus till they are ready. (e.g. g_webcam)
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
layerscape board sometimes reported some usb call trace, that is due to
kernel sent LPM tokerns automatically when it has no pending transfers
and think that the link is idle enough to enter L1, which procedure will
ask usb register has a recovery,then kernel will compare USBx_GFLADJ and
set GFLADJ_30MHZ, GFLADJ_30MHZ_REG until GFLADJ_30MHZ is equal 0x20, if
the conditions were met then issue occur, but whatever the conditions
whether were met that usb is all need keep GFLADJ_30MHZ of value is 0x20
(xhci spec ask use GFLADJ_30MHZ to adjust any offset from clock source
that generates the clock that drives the SOF counter, 0x20 is default
value of it)That is normal logic, so need remove the call trace.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In dwc3_pci_probe a call to platform_device_alloc allocates a device
which is correctly put in case of error except one case: when the call to
platform_device_add_properties fails it directly returns instead of
going to error handling. This commit replaces return with the goto.
Fixes: 1a7b12f69a ("usb: dwc3: pci: Supply device properties via driver data")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
composite_dev_cleanup call from the failure of configfs_composite_bind
frees up the cdev->os_desc_req and cdev->req. If the previous calls of
bind and unbind is successful these will carry stale values.
Consider the below sequence of function calls:
configfs_composite_bind()
composite_dev_prepare()
- Allocate cdev->req, cdev->req->buf
composite_os_desc_req_prepare()
- Allocate cdev->os_desc_req, cdev->os_desc_req->buf
configfs_composite_unbind()
composite_dev_cleanup()
- free the cdev->os_desc_req->buf and cdev->req->buf
Next composition switch
configfs_composite_bind()
- If it fails goto err_comp_cleanup will call the
composite_dev_cleanup() function
composite_dev_cleanup()
- calls kfree up with the stale values of cdev->req->buf and
cdev->os_desc_req from the previous configfs_composite_bind
call. The free call on these stale values leads to double free.
Hence, Fix this issue by setting request and buffer pointer to NULL after
kfree.
Signed-off-by: Chandana Kishori Chiluveru <cchiluve@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix interrupt storm generated by endpoints when working in FIFO mode.
The TX_COMPLETE interrupt is used only by control endpoints processing.
Do not enable it for other types of endpoints.
Fixes: 914a3f3b37 ("USB: add atmel_usba_udc driver")
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix the type of buf in __usbhsg_recip_send_status to
be __le16 to avoid the following sparse warning:
drivers/usb/renesas_usbhs/mod_gadget.c:335:14: warning: incorrect type in assignment (different base types)
drivers/usb/renesas_usbhs/mod_gadget.c:335:14: expected unsigned short
drivers/usb/renesas_usbhs/mod_gadget.c:335:14: got restricted __le16 [usertype]
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes the following sparse warnings by shifting 8-bits after
le16_to_cpu().
drivers/usb/renesas_usbhs/mod_gadget.c:268:47: warning: restricted __le16 degrades to integer
drivers/usb/renesas_usbhs/mod_gadget.c:268:47: warning: cast to restricted __le16
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes the following sparse warnings by using
a macro and a suitable variable type.
drivers/usb/gadget/udc/renesas_usb3.c:1547:17: warning: restricted __le16 degrades to integer
drivers/usb/gadget/udc/renesas_usb3.c:1550:43: warning: incorrect type in argument 2 (different base types)
drivers/usb/gadget/udc/renesas_usb3.c:1550:43: expected unsigned short [usertype] addr
drivers/usb/gadget/udc/renesas_usb3.c:1550:43: got restricted __le16 [usertype] wValue
drivers/usb/gadget/udc/renesas_usb3.c:1607:24: warning: incorrect type in assignment (different base types)
drivers/usb/gadget/udc/renesas_usb3.c:1607:24: expected unsigned short [assigned] [usertype] status
drivers/usb/gadget/udc/renesas_usb3.c:1607:24: got restricted __le16 [usertype]
drivers/usb/gadget/udc/renesas_usb3.c:1775:17: warning: restricted __le16 degrades to integer
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix the warnings generated by casting to/from __le16 without
using the correct functions.
Fixes the following sparse warnings:
drivers/usb/renesas_usbhs/common.c:165:25: warning: incorrect type in assignment (different base types)
drivers/usb/renesas_usbhs/common.c:165:25: expected restricted __le16 [usertype] wValue
drivers/usb/renesas_usbhs/common.c:165:25: got unsigned short
drivers/usb/renesas_usbhs/common.c:166:25: warning: incorrect type in assignment (different base types)
drivers/usb/renesas_usbhs/common.c:166:25: expected restricted __le16 [usertype] wIndex
drivers/usb/renesas_usbhs/common.c:166:25: got unsigned short
drivers/usb/renesas_usbhs/common.c:167:25: warning: incorrect type in assignment (different base types)
drivers/usb/renesas_usbhs/common.c:167:25: expected restricted __le16 [usertype] wLength
drivers/usb/renesas_usbhs/common.c:167:25: got unsigned short
drivers/usb/renesas_usbhs/common.c:173:39: warning: incorrect type in argument 3 (different base types)
drivers/usb/renesas_usbhs/common.c:173:39: expected unsigned short [usertype] data
drivers/usb/renesas_usbhs/common.c:173:39: got restricted __le16 [usertype] wValue
drivers/usb/renesas_usbhs/common.c:174:39: warning: incorrect type in argument 3 (different base types)
drivers/usb/renesas_usbhs/common.c:174:39: expected unsigned short [usertype] data
drivers/usb/renesas_usbhs/common.c:174:39: got restricted __le16 [usertype] wIndex
drivers/usb/renesas_usbhs/common.c:175:39: warning: incorrect type in argument 3 (different base types)
drivers/usb/renesas_usbhs/common.c:175:39: expected unsigned short [usertype] data
Note. I belive this to be correct, and should be a no-op on arm.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The cdns3_host_init() function is declared in host-export.h
but host.c does not include it. Add the include to have
the declaration present (and remove the declaration of
cdns3_host_exit which is now static).
Fixes the following sparse warning:
drivers/usb/cdns3/host.c:58:5: warning: symbol 'cdns3_host_init' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The declarations of ssusb_gadget_{init,exit} are
in the mtu3_dr.h file but the code does that implements
them does not include this. Add the include to fix the
following sparse warnigns:
drivers/usb/mtu3/mtu3_core.c:825:5: warning: symbol 'ssusb_gadget_init' was not declared. Should it be static?
drivers/usb/mtu3/mtu3_core.c:925:6: warning: symbol 'ssusb_gadget_exit' was not declared. Should it be static?
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Check memory resource existence before releasing it to avoid NULL
pointer dereference
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
After many randconfig builds, one configuration caused a link
error with dwc3-meson-g12a lacking the regmap-mmio code:
drivers/usb/dwc3/dwc3-meson-g12a.o: In function `dwc3_meson_g12a_probe':
dwc3-meson-g12a.c:(.text+0x9f): undefined reference to `__devm_regmap_init_mmio_clk'
Add the select statement that we have for all other users
of that dependency.
Fixes: c99993376f ("usb: dwc3: Add Amlogic G12A DWC3 glue")
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
A handful of drivers all have a trivial wrapper around their ioctl
handler, but don't call the compat_ptr() conversion function at the
moment. In practice this does not matter, since none of them are used
on the s390 architecture and for all other architectures, compat_ptr()
does not do anything, but using the new compat_ptr_ioctl()
helper makes it more correct in theory, and simplifies the code.
I checked that all ioctl handlers in these files are compatible
and take either pointer arguments or no argument.
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The .ioctl and .compat_ioctl file operations have the same prototype so
they can both point to the same function, which works great almost all
the time when all the commands are compatible.
One exception is the s390 architecture, where a compat pointer is only
31 bit wide, and converting it into a 64-bit pointer requires calling
compat_ptr(). Most drivers here will never run in s390, but since we now
have a generic helper for it, it's easy enough to use it consistently.
I double-checked all these drivers to ensure that all ioctl arguments
are used as pointers or are ignored, but are not interpreted as integer
values.
Acked-by: Jason Gunthorpe <jgg@mellanox.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: David Sterba <dsterba@suse.com>
Acked-by: Darren Hart (VMware) <dvhart@infradead.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Each of these drivers has a copy of the same trivial helper function to
convert the pointer argument and then call the native ioctl handler.
We now have a generic implementation of that, so use it.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Reviewed-by: Jiri Kosina <jkosina@suse.cz>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Prolific has developed a new USB to UART chip: PL2303HXN
PL2303HXN : PL2303GC/PL2303GS/PL2303GT/PL2303GL/PL2303GE/PL2303GB
The Vendor request used by the PL2303HXN (TYPE_HXN) is different from
the existing PL2303 series (TYPE_HX & TYPE_01).
Therefore, different Vendor requests are used to issue related commands.
1. Added a new TYPE_HXN type in pl2303_type_data, and then executes
new Vendor request,new flow control and other related instructions
if TYPE_HXN is recognized.
2. Because the new PL2303HXN only accept the new Vendor request,
the old Vendor request cannot be accepted (the error message
will be returned)
So first determine the TYPE_HX or TYPE_HXN through
PL2303_READ_TYPE_HX_STATUS in pl2303_startup.
2.1 If the return message is "1", then the PL2303 is the existing
TYPE_HX/ TYPE_01 series.
The other settings in pl2303_startup are to continue execution.
2.2 If the return message is "not 1", then the PL2303 is the new
TYPE_HXN series.
The other settings in pl2303_startup are ignored.
(PL2303HXN will directly use the default value in the hardware,
no need to add additional settings through the software)
3. In pl2303_open: Because TYPE_HXN is different from the instruction of reset
down/up stream used by TYPE_HX.
Therefore, we will also execute different instructions here.
4. In pl2303_set_termios: The UART flow control instructions used by
TYPE_HXN/TYPE_HX/TYPE_01 are different.
Therefore, we will also execute different instructions here.
5. In pl2303_vendor_read & pl2303_vendor_write, since TYPE_HXN is different
from the vendor request instruction used by TYPE_HX/TYPE_01,
it will also execute different instructions here.
6. In pl2303_update_reg: TYPE_HXN used different register for flow control.
Therefore, we will also execute different instructions here.
Signed-off-by: Charles Yeh <charlesyeh522@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
usb_composite_setup_continue() may be called before composite_setup()
return USB_GADGET_DELAYED_STATUS, then the controller driver will
delay status stage after composite_setup() finish, but the class driver
don't ask the controller to continue delayed status anymore, this will
cause control transfer timeout.
happens when use mass storage (also enabled other class driver):
cpu1: cpu2
handle_setup(SET_CONFIG) //gadget driver
unlock (g->lock)
gadget_driver->setup()
composite_setup()
lock(cdev->lock)
set_config()
fsg_set_alt() // maybe some times due to many class are enabled
raise FSG_STATE_CONFIG_CHANGE
return USB_GADGET_DELAYED_STATUS
handle_exception()
usb_composite_setup_continue()
unlock(cdev->lock)
lock(cdev->lock)
ep0_queue()
lock (g->lock)
//no delayed status, nothing todo
unlock (g->lock)
unlock(cdev->lock)
return USB_GADGET_DELAYED_STATUS // composite_setup
lock (g->lock)
get USB_GADGET_DELAYED_STATUS //handle_setup [1]
Try to fix the race condition as following:
After the driver gets USB_GADGET_DELAYED_STATUS at [1], if we find
there is a usb_request in ep0 request list, it means composite already
asked us to continue delayed status by usb_composite_setup_continue(),
so we skip request about delayed_status by composite_setup() and still
do status stage.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds UDC driver for tegra XUSB 3.0 device mode controller.
XUSB device mode controller supports SS, HS and FS modes
Based on work by:
Mark Kuo <mkuo@nvidia.com>
Hui Fu <hfu@nvidia.com>
Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The newline from the unknown link state tracepoint doesn't follow the
other tracepoints, and it looks unsightly. Let's remove it.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Testing on different generations of Lantiq MIPS SoC based boards, showed
that it takes up to 1500 us until the core reset bit is cleared.
The driver from the vendor SDK (ifxhcd) uses a 1 second timeout. Use the
same timeout to fix wrong hang detections and make the driver work for
Lantiq MIPS SoCs.
At least till kernel 4.14 the hanging reset only caused a warning but
the driver was probed successful. With kernel 4.19 errors out with
EBUSY.
Cc: linux-stable <stable@vger.kernel.org> # 4.19+
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Simplify this function implementation by using a known wrapper function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There is a statement that is indented too deeply, remove
the extraneous tabs.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
On a system that often re-configures a USB gadget device the kernel log
is filled with:
configfs-gadget gadget: high-speed config #1: c
Reduce the verbosity of this print to debug.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/usb/gadget/legacy/mass_storage.c: In function msg_do_config:
drivers/usb/gadget/legacy/mass_storage.c:108:19: warning: variable opts set but not used [-Wunused-but-set-variable]
It is not used since commit f78bbcae86 ("usb: f_mass_storage:
test whether thread is running before starting another")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/usb/gadget/legacy/acm_ms.c: In function acm_ms_do_config:
drivers/usb/gadget/legacy/acm_ms.c:108:19: warning: variable opts set but not used [-Wunused-but-set-variable]
It is not used since commit f78bbcae86 ("usb: f_mass_storage:
test whether thread is running before starting another")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Exact a new static function to do status stage
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
