It's hard to follow the numbers so rename it with enum
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Scan API was changed to support 6Ghz channels as well.
Support the new version.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
New FW versions introduces LTR feature enablement by default.
For such FW versions, driver (mvm/xvt) should not send
host command to enable LTR feature, also it should be possible to
override LTR configuration through the debugfs.
1. Send LTR feature enablement command only for FW versions
which does not advertises SET_LTR_GEN2 capability.
2. Implement ltr_config file in debugfs for LTR configuration override.
Signed-off-by: Alex Malamud <alex.malamud@intel.com>
Support the new DBGC_SUSPEND_RESUME command to change the recording state.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The op mode should stop the debug recording and not the transport layer.
Rename iwl_fwrt_stop_device into iwl_fw_dbg_stop_sync and move the debug
stop recording to it.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The recording functions are quite big to be inline and the driver should
expose only the stop and restart functions that are allowed to be used
rather then the internal helper functions. Move the functions from the
header file.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case that there are OBSS that do not know how to properly
interpret 26-tone RU OFDMA transmissions, instruct the FW not
to use such transmissions.
The check is currently only performed upon association.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of allocating memory for which we have an upper
limit, use a small buffer on stack.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We will soon be using a new notification that will be
initiated by the driver, sent to the firmware and sent
back to all the RSS queues by the firmware. This new
notification will be useful to synchronize the NSSN across
all the queues.
For now, don't send the notification, just add the code to
handle it. Later patch will add the code to actually send
it.
While at it, validate the baid coming from the firmware to
avoid accessing an array with a bad index in the driver.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwl_mvm_send_cmd returns 0 when the command won't be sent
because RF-Kill is asserted. Do the same when we call
iwl_get_shared_mem_conf since it is not sent through
iwl_mvm_send_cmd but directly calls the transport layer.
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The 0xF6 command used to start and stop the recording from 22560 devices
was removed. This is causing an assert when the driver tries to alter
the recording state.
Remove the use of the command.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In ini debug mode the recording does not restart unless legacy monitor
configuration is also given.
Add dbg_ini_dest field to trans to indicate the debug monitor
destination to solve this.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Unite iwl_trans debug related fields under iwl_trans_debug struct to
increase readability and keep iwl_trans clean.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are several flows where the driver checks if it runs in ini mode.
Some of these flows are no longer used in ini mode or there is another
condition that check the ini mode in the same flow. Either way, those
conditions are redundant. Remove the redundant conditions.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Apply buffer allocation TLV only if it is set to apply point
IWL_FW_INI_APPLY_EARLY.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The driver should delay only in recording stop flow between writing to
DBGC_IN_SAMPLE register and DBGC_OUT_CTRL register. Any other delay is
not needed.
Change the following:
1. Remove any unnecessary delays in the flow
2. Increase the delay in the stop recording flow since 100 micro is
not enough
3. Use usleep_range instead of delay since the driver is allowed to
sleep in this flow.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: 5cfe79c8d9 ("iwlwifi: fw: stop and start debugging using host command")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
South Korea is adding a more strict SAR limit called "Limb SAR".
Currently, WGDS SAR offset group 3 is not used (not mapped to any country).
In order to be able to comply with South Korea new restriction:
- OEM will use WGDS SAR offset group 3 to South Korea limitation.
- OEM will change WGDS revision to 1 (currently latest revision is 0)
to notify that Korea Limb SAR applied.
- Driver will read the WGDS table and pass the values to FW (as usual)
- Driver will pass to FW an indication that Korea Limb SAR is applied
in case table revision is 1.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support adaptive dwell high band default number of APs new api.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The info struct contains data about the FW, HW, RF and the debug
configuration.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support to debug info TLV.
The TLV contains human readable naming of the FW image and the
debug configuration.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Use a different barker for ini dump to allow differentiation from legacy
dump. Also it allows to remove INI_BIT from dump TLVs.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a dump trigger is fired, the driver sets IWL_FWRT_STATUS_DUMPING and
aborts any consecutive dump collection.
To allow consecutive triggers firing, use 5 dump workers and allocate
them upon incoming dump collection requests.
This functionality is needed since in ini debug mode each trigger may
have entirely different memory regions to collect unlike the legacy
mode in which all the triggers dump the same memory regions.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Allows to abort region collection in case the region size is 0.
It is needed for future regions that their size might be 0.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Update the CSI API to the new version supported by the firmware.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Unite dump memory ranges under a single struct and add a specific header
for each type of memory.
Also, maintain a single version to all dump structures.
This cleanup is also needed for the future addition of FW notification
regions and others.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Improve the robustness of the dump collection flow in case of an early
error:
1. in iwl_trans_pcie_sync_nmi, disable and enable interrupts only if
they were already enabled
2. attempt to initiate dump collection in iwl_fw_dbg_error_collect only
if the device is enabled
3. check Tx command queue was already allocated before trying to collect it
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Read fseq info from FW registers and print it upon fw assert.
The print is needed since the fseq version coming from the TLV might
not be the actual version that is used.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Most likely the last patchset of new feature for 5.2, and this time we
have quite a lot of new features. Most obvious being rtw88 from
Realtek which supports RTL8822BE and RTL8822CE 802.11ac devices. We
have also new hardware support for existing drivers and improvements.
There's one conflict in iwlwifi, my example conflict resolution below.
Major changes:
iwlwifi
* bump the 20000-series FW API version
* work on new hardware continues
* RTT confidence indication support for Fine Timing Measurement (FTM)
* an improvement in HE (802.11ax) rate-scaling
* add command version parsing from the fimware TLVs
* add support for a new WoWLAN patterns firmware API
rsi
* add support for rs9116
mwifiex
* add support for SD8987
brcmfmac
* add quirk for ACEPC T8 and T11 mini PCs
rt2x00
* add RT3883 support
qtnfmac
* fix debugfs interface to support multiple cards
rtw88
* new driver
mt76
* share more code across drivers
* add support for MT7615 chipset
* rework DMA API
* tx/rx performance optimizations
* use NAPI for tx cleanup on mt76x02
* AP mode support for USB devices
* USB stability fixes
* tx power handling fixes for 76x2
* endian fixes
Conflicts:
There's a trivial conflict in
drivers/net/wireless/intel/iwlwifi/fw/file.h, just leave
IWL_UCODE_TLV_FW_FSEQ_VERSION to the file. 'git diff' output should be
just empty:
diff --cc drivers/net/wireless/intel/iwlwifi/fw/file.h
index cd622af90077,b0671e16e1ce..000000000000
--- a/drivers/net/wireless/intel/iwlwifi/fw/file.h
+++ b/drivers/net/wireless/intel/iwlwifi/fw/file.h
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJczDAZAAoJEG4XJFUm622blLgH/jdBKEq9i1m5dtLi48u4sgPV
NsnPhR5XQjpbYpmvgPslKLxWzZq6A0P+lo9QqTXkP/QRyJLu7RnoY1c2wVsQbWaK
VTXc0cROzWt0ihAt8Mc/rEsZpISVnQ9mJbTd/kSJM9WlDeIg0jcJvnEAdQiEmM5t
2t+zZ5CupUXYbGE3zWHL1GSjBD9f0v7zyrNxYNGfvqhDEXhTFWAmVuRtfoAVlRU+
dt1HMv+qdxgoF6Uvaw/kgY09mDvdrfy2EVL0q7S3TKceute60SWf7de2sToI/rMQ
snUnVqTIIUnWPl6g+C3Bp2TbdZhy6XCSRsMFOVa2i1Lt+z1qe3dTr3hjxTQWRhE=
=uLaP
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2019-05-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.2
Most likely the last patchset of new feature for 5.2, and this time we
have quite a lot of new features. Most obvious being rtw88 from
Realtek which supports RTL8822BE and RTL8822CE 802.11ac devices. We
have also new hardware support for existing drivers and improvements.
There's one conflict in iwlwifi, my example conflict resolution below.
Major changes:
iwlwifi
* bump the 20000-series FW API version
* work on new hardware continues
* RTT confidence indication support for Fine Timing Measurement (FTM)
* an improvement in HE (802.11ax) rate-scaling
* add command version parsing from the fimware TLVs
* add support for a new WoWLAN patterns firmware API
rsi
* add support for rs9116
mwifiex
* add support for SD8987
brcmfmac
* add quirk for ACEPC T8 and T11 mini PCs
rt2x00
* add RT3883 support
qtnfmac
* fix debugfs interface to support multiple cards
rtw88
* new driver
mt76
* share more code across drivers
* add support for MT7615 chipset
* rework DMA API
* tx/rx performance optimizations
* use NAPI for tx cleanup on mt76x02
* AP mode support for USB devices
* USB stability fixes
* tx power handling fixes for 76x2
* endian fixes
Conflicts:
There's a trivial conflict in
drivers/net/wireless/intel/iwlwifi/fw/file.h, just leave
IWL_UCODE_TLV_FW_FSEQ_VERSION to the file. 'git diff' output should be
just empty:
diff --cc drivers/net/wireless/intel/iwlwifi/fw/file.h
index cd622af90077,b0671e16e1ce..000000000000
--- a/drivers/net/wireless/intel/iwlwifi/fw/file.h
+++ b/drivers/net/wireless/intel/iwlwifi/fw/file.h
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add region type checking during regions parsing to avoid attempts to
parse unsupported or illegal region types.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In iwl_fw_ini_get_trigger_len the driver allocates space for memory
regions regardless of their domain and in iwl_fw_ini_dump_trigger the
driver aborts trigger collection of disabled domain. This diff causes
unneeded memory allocation and traling zeros in the dump file.
Solve this behavior by enforcing domain checking in
iwl_fw_ini_get_trigger_len
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the dump info, the driver sets device_family to
IWL_FW_ERROR_DUMP_FAMILY_7 in case IWL_FW_ERROR_DUMP_FAMILY_7 is used or
IWL_FW_ERROR_DUMP_FAMILY_8 otherwise. This information is misleading and
incorrect since the driver sets the device family to 8 to any device that
is from family 8 and later, e.g. device family 9 is represented as 8 in
the dump.
Also, the device family enum is known only to the driver and
does not give any information to the FW developer
Change the device family to HW type to give propper data about the nic
in use.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Allows to configure a periodic data collection
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add LMAC_ERROR_TABLE and UMAC_ERROR_TABLE region types and handle them
in the same way as we handle DEVICE_MEMORY.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In newer firmware images there's a command version TLV that
states, for each listed command or notification, which version
of the command and/or notification structure is used. Read and
keep this data to be able to use it in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support fseq tlv and print fseq version to dmesg.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add new definitions for the WoWLAN patterns API version 2 and support
for version 2 of the WoWLAN patterns command without implementing the
new features. With this commit we only supporting the existing
bitmask pattern match. Use the new version only if the TLV is set.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case the the trigger occurrences is zero or force_restart is set, the
driver sets IWL_FWRT_STATUS_DUMPING without actually scheduling trigger
collection. At this point no other dump collection can be performed.
Solve this by setting IWL_FWRT_STATUS_DUMPING bit only when the driver
is surely going to schedule dump collection
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The range response notification API has changed to add a value that
indicates the confidence of the rtt result.
Support the new API and print the rtt confidence for debug.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Allows to dump periphery memory on ax210 devices.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add debug prints to the ini flow and rewrite existing prints to provide
more information
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
IWL_FW_INI_REGION_CSR and IWL_FW_INI_REGION_NOTIFICATION does not have
memory addresses attached to them so the driver should skip them when
parsing the region tlv.
Also, instead of declearing what region types should skip the addition of
the memory addresses, declare what regions have addition of memory
addresses.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
TFD_*_SLOTS and IWL_*_QUEUE_SIZE both define the TX queue
size (number of TFDs).
Get rid of TFD_*_SLOTS and use only IWL_*_QUEUE_SIZE.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Nothing really special standing out this time, iwlwifi being the most
active driver.
Major changes:
iwlwifi
* send NO_DATA events so they can be captured in radiotap
* support for multiple BSSID
* support for some new FW API versions
* support new hardware
* debugfs cleanups by Greg-KH
qtnfmac
* allow each MAC to specify its own regulatory rules
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcuHgsAAoJEG4XJFUm622bfo8H/3uRRxsQBHGg6e3NpELaxpNV
IfrPDtvxyfILzIepBBhnZYUY0OrlTHKfMmzFBD9FFMojsxBYddnLZ/0iKUNKfwLm
KzToW/64YJ784dc+tw85gjh8I3MB+RRoD0l01M1HuOkzQ4hDNEGK3IsMHsBs/oTZ
huiqTYsTxStOj53vOpQiBFZ1pYBtvGLMxBdSepDcR27bgT1gwriynCSkSNglDH8z
/t3m6hDGtZa6uVkoIVH+BAMu6+vt+vIkU/TOdmiW/zqBL2JYq6cDE0uIb3bLAzN6
uvS1Rj42P3OwHUwFavlUBdr5Rdcj6P24S5ZhtVaGGWCBjMZI5/nO7IjzwyQnQuQ=
=/6q9
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2019-04-18' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.2
Nothing really special standing out this time, iwlwifi being the most
active driver.
Major changes:
iwlwifi
* send NO_DATA events so they can be captured in radiotap
* support for multiple BSSID
* support for some new FW API versions
* support new hardware
* debugfs cleanups by Greg-KH
qtnfmac
* allow each MAC to specify its own regulatory rules
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In ini debug TLVs bit 24 is set. The driver relies on it in the memory
allocation for the debug configuration. This implementation is
problematic in case of a new debug TLV that is not supported yet is added
and uses bit 24. In such a scenario the driver allocate space without
using it which causes errors in the apply point enabling flow.
Solve it by explicitly checking if a given TLV is part of the list of
the supported ini debug TLVs.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: f14cda6f3b ("iwlwifi: trans: parse and store debug ini TLVs")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support API change to pass all mbssid parameters to the firmware.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The driver calculates memory regions dump size, allocate memory and
fills the data. The driver fills the radio registers data only if the
memory size of the fifos is greater then zero, so in case the user
masked out the fifos from the dump, the driver will skip filling the
radio register data.
Solve this by checking filling radio registers data independently from
fifos data.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The region registers comes in abolute value so read the registers before
applying the rx fifo offset.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since iwl_dump_ini_mem receive struct iwl_fw_ini_region_cfg which holds
the region type, there is no point to pass the type separately.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
remove redundant curly brackets from iwl_fw_ini_dump_trigger and
iwl_fw_ini_get_trigger_len
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add write pointer and cycle count registers to smem monitor header.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add sizeof(struct iwl_fw_ini_error_dump_range) to the header of the dram
monitor.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
AX210 devices will use u64 for the base address to the DRAM monitor
buffer. To support this, change the structure for all device families
so both address sizes fit.
Also move range_data_size to the top of the struct to ease the parsing
of the memory range.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add to the fifo dump the registers addresses.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add the region id of the collected memory to the header of the memory
region.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add version to dump header to allow future changes of the dump struct,
once the ini debug flow becomes operational, without breaking backwards
compatibility.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add the offset to the base address of a memory region to show the actual
addresses being read.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The driver is using range->start_addr before assigning it a value.
Set value into range->start_addr and then use it.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Enforce domain checking before sending host commands and collecting
memory regions. Currently the driver supports always on domain only.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Differentiate between SW and HW error interrupts and support ini HW
error trigger.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
align to ini debug struct version 1 and enforce version checking.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Separate between ini and legacy dump flows to allow adding ini triggers
that are not supported in the legacy flow and to increase readabilty.
iwl_fw_dbg_ini_collect function is now called with legacy trigger id and
_iwl_fw_dbg_ini_collect is called with ini trigger id.
Also make the actual dumping function static so that any dump collection
will go through iwl_fw_dbg_collect_sync.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Allows to perform monitor dumping on AX210 device family
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The layout of the RBD (receive buffer descriptor) isn't quite right,
the hardware ended up being implemented differently. Switch to the
correct RBD layout. While at it, remove the now useless extra defines.
Also, switch the CD (completion descriptor) to the right format, which
is basically just a code cleanup because the only field we really used
(rbid) is still in the same place. We may need fragmentation later if
we ever want to use it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Newer FWs use a new format of the SCAN_OFFLOAD_PROFILES_QUERY_RSP,
which now supports indicating match on an higher number of channels.
Modify the code to support both the old format and the newer one,
based on a FW TLV.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support REGULATORY_NVM_GET_INFO_RSP_API_S_VER_4.
This API adds the new 6-7GHz channels.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Send to FW modify command for every beacon we receive during channel
switch. FW will track the count, and make sure the event is scheduled
in time even if AP changed count.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case of alive interrupt timeout or any failure in the init flow
the driver generates FW nmi. The driver assumes that the nmi will
generate SW interrupt. This assumption does not hold and leads to faulty
behavior in the recovery flow.
Solve this by using sync nmi, this way, even if the driver does not
receive SW interrupt, it still starts the recovery flow.
Also remove the wait queue from iwl_fwrt_stop_device since the driver is
handling the SW interrupt synchronously.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The driver initiates the size value with the size of the struct and then
adds the size of the data and checks if the size is zero so size can not
be equal to zero.
Solve this by getting the data size, check that it is not equal to zero
and only then add the struct size.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: 7a14c23dcd ("iwlwifi: dbg: dump data according to the new ini TLVs")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case the driver fails to dump a memory region, and this is the last
region, then partial region would be extracted.
Solve this by setting the data to zero in case of failure.
This will cause dump to be a list of consecutive successful memory
regions and trailing zeros with no partial memories extracted.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Most likely the last set of patches for 5.1. WPA3 support to ath10k
and qtnfmac. FTM support to iwlwifi and ath10k. And of course other
new features and bugfixes.
wireless-drivers was merged due to dependency in mt76.
Major changes:
iwlwifi
* HE radiotap
* FTM (Fine Timing Measurement) initiator and responder implementation
* bump supported firmware API to 46
* VHT extended NSS support
* new PCI IDs for 9260 and 22000 series
ath10k
* change QMI interface to support the new (and backwards incompatible)
interface from HL3.1 and used in recent HL2.0 branch firmware
releases
* support WPA3 with WCN3990
* support for mac80211 airtime fairness based on transmit rate
estimation, the firmware needs to support WMI_SERVICE_PEER_STATS to
enable this
* report transmit airtime to mac80211 with firmwares having
WMI_SERVICE_REPORT_AIRTIME feature, this to have more accurate
airtime fairness based on real transmit time (instead of just
estimated from transmit rate)
* support Fine Timing Measurement (FTM) responder role
* add dynamic VLAN support with firmware having WMI_SERVICE_PER_PACKET_SW_ENCRYPT
* switch to use SPDX license identifiers
ath
* add new country codes for US
brcmfmac
* support monitor frames with the hardware/ucode header
qtnfmac
* enable WPA3 SAE and OWE support
mt76
* beacon support for USB devices (mesh+ad-hoc only)
rtlwifi
* convert to use SPDX license identifiers
libertas_tf
* get the MAC address before registering the device
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJccAnlAAoJEG4XJFUm622bxxMH/2cz2GEuDQXOwfYLnCUwFES8
vqTdMWnlfqGQvsTyvtSp91KqsL3hE2FB1Cu3n6/vzND3C7afT0V2/QlU7Pmgr8sR
1gnJnu0NJT5SZfzcTsqwt8rFw9lQZ3HcvEcfNo6T5KUyyY7FGCNGR5H27nvoKOP3
ea1h7U80loPV40sGTI8jj963wa9LNHUrjHTK4wY+KMWECgZuD/fHeE9YPB9MTdff
lJ5bWCoQmuJddvTtC+X0tOAsCkxgdbbw6ieKqzep8H4gtUjerZD+V8uUdbtpr7IL
sWPoaqrrADMv9cZtDVj+pEtNIJ3mpfuHYFKSON9jy/uxygeFTfVzLu43RFreDp8=
=D15/
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2019-02-22' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.1
Most likely the last set of patches for 5.1. WPA3 support to ath10k
and qtnfmac. FTM support to iwlwifi and ath10k. And of course other
new features and bugfixes.
wireless-drivers was merged due to dependency in mt76.
Major changes:
iwlwifi
* HE radiotap
* FTM (Fine Timing Measurement) initiator and responder implementation
* bump supported firmware API to 46
* VHT extended NSS support
* new PCI IDs for 9260 and 22000 series
ath10k
* change QMI interface to support the new (and backwards incompatible)
interface from HL3.1 and used in recent HL2.0 branch firmware
releases
* support WPA3 with WCN3990
* support for mac80211 airtime fairness based on transmit rate
estimation, the firmware needs to support WMI_SERVICE_PEER_STATS to
enable this
* report transmit airtime to mac80211 with firmwares having
WMI_SERVICE_REPORT_AIRTIME feature, this to have more accurate
airtime fairness based on real transmit time (instead of just
estimated from transmit rate)
* support Fine Timing Measurement (FTM) responder role
* add dynamic VLAN support with firmware having WMI_SERVICE_PER_PACKET_SW_ENCRYPT
* switch to use SPDX license identifiers
ath
* add new country codes for US
brcmfmac
* support monitor frames with the hardware/ucode header
qtnfmac
* enable WPA3 SAE and OWE support
mt76
* beacon support for USB devices (mesh+ad-hoc only)
rtlwifi
* convert to use SPDX license identifiers
libertas_tf
* get the MAC address before registering the device
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge net-next to resolve a conflict and to get the mac80211
rhashtable fixes so further patches can be applied on top.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Update element names and new fields according to D3.3 of
the HE spec.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement Rx fifos dump in the new dump mechanism.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Implement Tx fifos dump in the new dump mechanism.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add iwl_fw_ini_region_cfg region struct to fill_header handler of
iwl_dump_ini_mem_ops. it is needed for future support in fifos dumping.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Make fill_range handler of iwl_dump_ini_mem_ops accept a generic range
pointer. It is needed for future support in fifos dumping.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Make the get size handler of iwl_dump_ini_mem_ops include the total
size of the region. It is needed for fifos dumping.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add informative print in case the range is not available.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The driver sets ignore_consec to -1 which is 0xffffffff in u32
so when iwl_fw_ini_trigger_on is called, it will always return false
and each trigger could be used only once.
Solve this by removing the assignment to -1.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: fe1b7d6c28 ("iwlwifi: add support for triggering ini triggers")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
After the FW image was loaded for the first time,
fwrt->smem_cfg.num_lmacs value will no longer be zero since we don't
clean it when we stop the device. So if we load the image once and then
we fail on a consecutive attempt, the driver will abort any dumping.
Solve this by removing the condition. It is safe to remove since
when we do the actual dumping in iwl_fw_dbg_collect_sync we check
that STATUS_DEVICE_ENABLED bit is still active.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The size of the buffer is IWL_FW_TRIGGER_ID_NUM - 1 which is equal to
IWL_FW_TRIGGER_ID_HOST_CHANNEL_SWITCH_COMPLETE so if the driver receives
this trigger, it will cause a buffer overflow.
Solve this by increasing the buffer size by 1.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: fe1b7d6c28 ("iwlwifi: add support for triggering ini triggers")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Enable ignore consecutive trigger feature which allows to configure the
driver to skip consecutive triggers from the same type.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fix several issues related to dump delay:
1. In legacy dump trigger, use stop_delay field instead of trig_dis_ms.
2. ini delay is messured in usec so align both ini and legacy to usec.
3. schedule_delayed_work receives the delay value in jiffies so
translate the dump delay to jiffies.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: ea7cb82938 ("iwlwifi: dbg: make trigger functions type agnostic")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The FTM new API uses API TLV bit 15. The driver mistakenly uses
this bit for beacon filter API, although no TLV was assigned for
the beacon filter API. For now, make beacon filter use bit 16
instead (not set by the fw anyway). Once a TLV is assigned to the
beacon filter API it should be updated.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
- The FW supports up to 4 concurrent scans, so adjust the definitions
accordingly.
- Only a single periodic scan is supported, so enforce it in the code.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
D3 debug data is disabled by default. Currently it is done by tampering
the dump mask. Add an operation that will allow this to be changed
without recompilation.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In AX210 family, UMAC periphery address space moved from
0xA00000 to 0xD00000.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Many periphery addresses have changed in AX210 devices.
Until sorting out which peripheries should be dumped, skip
that step for now.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In low power modes, the chip clock source for platform integrated
devices is 32kHz. It is generated internally and supplied by a crystal
oscillator. However using a 32kHz sourced from crystal oscillator
has high power penalty.
There is an option to get an external 32kHz clock from the platform. Past
experience shows that the reliability is platform dependent,
i.e. on some platforms it works good and on other it doesn’t.
Working from external clock will save 0.5 mW in sleep state, from overall
1.8mW that we have today, i.e. almost 30%.
Each OEM can enable or disable the use of the external 32kHz clock by
setting a BIOS configuration. In case the OEM configured to use 32kHz
external clock the driver will pass this indication to the FW.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add new API and TLV for the ability to send commands in the beginning
and end of reset flow.
The full flow of recovery is:
1. While loading FW, get address (from the TLV) of target buffer
to read in case of reset
2. If an error/assert happens read the address data from step 1.
3. Reset the HW and load the FW.
4. Send the data read in step 2.
5. Add station keys
6. Send notification to FW that reset flow is done.
The main use of the recovery flow is for support in PN/SN recovery
when offloaded
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Trigger field ignore_default was changed to override_trig.
The first byte of the field indicates the driver to override existing
configuration or keep the previous one
The second byte of the field indicated the driver to replace the regions
of the previous trigger or to append new regions to it.
Change the way the active triggers are maintained to support trigger
override in different apply points.
Do this by making a trigger that updates at runtime by the
triggers that are being used in the different apply points.
In case of an assert, the driver does not reconfigure the triggers
and uses the old configuration which leads to undefined behavior.
Solve this by clearing the triggers in assert recovery flow.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
TLV 54 holds umac debug related addresses.
TLV 55 holds lmac debug related addresses.
These TLVs aim to replace the alive notification data in the future.
Parse and keep error table addresses received from the TLVs
for both lmac and umac and use these addresses instead of the pointer
received from alive notification.
The feature supports only unified image.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support for FTM initiator, i.e. peer measurements with FTM
if the firmware supports FTM.
Additionally, add two defines we depend on in
include/linux/ieee80211.h.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support for FTM responder for hardware/firmware combinations
that advertise support for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Implement monitor dram memory dump in the new dump mechanism.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Implement monitor sram memory dump in the new dump mechanism.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Implement paging memory dump in the new dump mechanism.
To support this change, moved iwl_self_init_dram strcut from trans_pcie
to trans so that it will accessible via fw_runtime.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Implement device internal memory dump in the new dump mechanism.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Implement csr memory dump in the new dump mechanism.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Create a skeleton to unite all memory dumps in ini mode.
Implement prph dump with the new skeleton.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
New fields were added to struct iwl_fw_ini_region_cfg.
add those field and apply the changes the result from this change
offset field is used to differentiate between the different LMACs
and any memory access to the region addresses should be
base_addr + offset.
A fifo struct is to hold the meta data needed for fifo regions
Also move range_data_size and num_of_ranges into a struct under the
union to be aligned to the struct in the FW.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Update iwl_beacon_filter_cmd to support
BEACON_FILTER_CONFIG_API_S_VER_4.
Currently driver configs them to be zero
(i.e. disable them, so no change is applied).
Signed-off-by: Avigail Grinstein <avigail.grinstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are several flows in that can cause redundant allocation.
In case the driver reaches the maximum amount of blocks allowed, it
allocates the buffer and only then checks if it reached the maximum
amount of blocks and return without freeing the buffer,
causing a memory leak.
Solve this by moving the check of the amount of buffers being used
before the allocation.
In case there was an assert, the apply points are being reused,
causing that for each assert, the driver allocates a new redundant
buffer.
Solve this by adding a new is_alloc field to indicate if the driver
already allocated memory for the requested buffer.
Also, split iwl_fw_dbg_buffer_allocation function into
iwl_fw_dbg_buffer_allocation and iwl_fw_dbg_buffer_apply
to increase the clearity of the flow.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: d47902f9f7 ("iwlwifi: dbg: add apply point logic")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Align the documentation of the structs with the latest version in
the FW.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are several dumping flows in the driver in case of a fail
prior to operational.
In some cases we get 2 dumps while in others we get none.
Fix this by uniting the different flows.
Add a different dump type to driver triggered dumps in case we want
a dump but did not got assert, and make all dumping go through
iwl_fw_dbg_collect_desc to avoid multiple dumps.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware is changing the format of the beacon
notification to remove the dependency on the Tx response
format.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The driver should support 64 region ids. Update
IWL_FW_INI_MAX_REGION_ID accordingly.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Align the triggers enum in the driver to the one in the FW.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are two cases that can cause the alive flow to fail,
an assert or a timeout.
Currently we mask any incoming asserts when we wait for alive.
Solve this by differentiating between the two cases:
1. Let the regular error handling to handle a received assert
2. Do a dump collection in the case of a timeout
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: f38efdb293 ("iwlwifi: add dump collection in case alive flow fails")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we do channel switch, we used to schedule time events
ourselves. This was offloaded to FW. Support the new command
and flow.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Prior to gen2 we allocate the paging memory via alloc_pages
which requires passing ownership on the memory between the
cpu and the device using dma_sync_single_for_cpu and
dma_sync_single_for_device.
Add missing dma_sync_single_for_device in iwl_dump_paging
after copying the memory.
since gen2, we allocate the paging memory using dma_alloc_coherent
which does not need passing ownership between the cpu and device.
Remove unneeded call to dma_sync_single_for_cpu in
iwl_trans_pcie_dump_data prior to copying the memory.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: 5538409ba3 ("iwlwifi: pcie: support page dumping in wrt in gen2")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some of the region struct fields have misleading naming
change those fields to have an informative naming
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
change IWL_FW_INI_LOCATION_SRAM_INVALID into IWL_FW_INI_LOCATION_INVALID
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
update ini struct documentation to the structs being used in the FW
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The driver sets dump_mask value instead of BIT(value).
fix it by updating dump_mask correctly.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: 7a14c23dcd ("iwlwifi: dbg: dump data according to the new ini TLVs")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The driver uses ignore_consec instead of dump_delay.
Fix it by using dump_delay as expected.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: fe1b7d6c28 ("iwlwifi: add support for triggering ini triggers")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
in case of a user trigger while ini is enable we change
FW_DBG_TRIGGER_USER to IWL_FW_TRIGGER_ID_USER_TRIGGER in
iwl_fw_dbg_collect and then again we attempt to do so in
_iwl_fw_error_ini_dump which causes to abort the dump.
Fix it by removing the second check in _iwl_fw_error_ini_dump.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: 7a14c23dcd ("iwlwifi: dbg: dump data according to the new ini TLVs")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Use the same flags we use in the legacy buffer allocation.
Missing __GFP_NOWARN will cause an unwanted warning incase
we fail to allocate.
Missing __GFP_ZERO will give a buffer initially filled with
garbage which can make debug difficult in case our wrap count is zero.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: d47902f9f7 ("iwlwifi: dbg: add apply point logic")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Change iwl_fw_channel_info structure so it can have channel number
greater than 255. This is needed for 6 GHz channel numbers.
Change all relevant structs and member accesses accordingly.
The new API is indicated by a TLV capability bit.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Implement CSI (channel estimation matrix) reporting in the mvm
driver, if the firmware has the capability.
Currently only a debugfs API is provided as the API is still
under discussion.
For now, RX aggregation must be disabled to use this feature
on data frames as we haven't found a good way to attach the
data to A-MPDUs, given complexities with multi-queue.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add the location/time-of-flight/FTM APIs that we'll use in
follow-up patches to implement FTM responder and initiator.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This is an ancient (~2015) implementation that no longer matches
the firmware in any way, and most likely never worked. Remove all
of it so it can be reintroduced properly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Harden the fwrt->fw->img array access by making sure the cur_fw_img
value doesn't go out of bounds.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This function is supposed to be used as an inline function and is in a
header file, so make it inline.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Clean up the LDBG config command to not be called "continuous
recording", and while at it actually remove the continuous
recording implementation completely since it was only used for
store & forward architectures.
This also fixes a bug at least in iwl_fw_dbg_buffer_allocation()
because what's now "__le32 type" (matching the firmware) used to
be "__le16 enable_recording", so the buffer allocation config
sub-struct would erroneously have started at the wrong offset.
In the other cases this didn't actually lead to a bug as other
bytes in pad[] were all zeroes, so accessing the 16-bit value as
a 32-bit value wouldn't make a difference (in little endian.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Take the NSS value from 'rx_vec' rather than from 'rate_n_flags'.
The rate_n_flags has only 2 bits for the NSS giving a max of 4SS
(0 = 1SS etc.). Since there may be up to 8SS use the rx_vec which
has 3 bits for the NSS.
While at it, fix the rx_vec array to length of 2.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
These are unused by both firmware and driver, remove them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The value in num_lmac can be bigger than mem_cfg->lmac array,
warn in case it's bigger.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Fixes: 68025d5f9b ("iwlwifi: dbg: refactor dump code to improve readability")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The driver assumes certain sizes and lengths aren't crossed in some
places. Make sure this indeed happens.
Found by Klocwork.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A few commands refer to a struct that no longer exists
in the mentioned name. Our trace-cmd parsing scripts
rely on these mentioned names and can't find them,
resulting in these commands not being parsed nicely.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add prph dump addresses to support prph dump in 22000 HW.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The new (CDB) statistics API is used by non-CDB devices
as well. Look at the right TLV flag to know which version
of the statistics notification to use.
To avoid confusion, remove the _cdb suffix from the
structure name.
While at it, remove a structure that was never used.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fixes: 678d9b6ddd ("iwlwifi: mvm: update rx statistics cmd api")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add to the dump the number of lmacs, the error id of the umac
and the error id of lmac1, if supported.
In case the reason for the dump trigger is not an assert
the error id is zero.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add debug data to the warning issued when getting wrong region
id from firmware.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These macros are never used and are actually wrong, so it's very
confusing. Remove them.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add the rt status of the last assert or 0 if the dump collection was
not initiated by an assert. Add the number of rx and tx fifos in use.
These fields are added to dump info lst file.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Handle RX no data notification, which is used for advertising NDP to
radiotap.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The FW expects to get the ppe value for each NSS-BW pair in the same
format as in the he phy capabilities IE, which means that a value of 0
implies ppe should be used for BPSK (mcs 0). If there are no PPE
thresholds in the IE, or if for some NSS-RU pair there's no threshold
set for it (this could happen because it's a variable-sized field), it
means no PPE should not be used for that pair, so the value sent to FW
should be 7 which corresponds to "none".
Fixes: 514c30696f ("iwlwifi: add support for IEEE802.11ax")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware changed the PHY data API, so follow suit.
Some data is now available even for HT/VHT frames, so
the info type in the metadata was changed. This change
isn't backwards compatible, but
1) the firmware with the old API was never released;
2) the only overlap in the info type field is from the
old type of TB to the new of HT, so this basically
just means that with older FW and newer driver the
data will be considered missing.
While at it, remove the extra code to set the LTF syms
corresponding to the streams and use the data from the
device instead - we don't really need this in any case
other than when we have it from the device.
As the new API gives use the spatial reuse 1-4 fields
for trigger-based PPDUs, also expose that to radiotap.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When ini TLVs are loaded, dump data according to the
stored configuration.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
First set of patches for 4.21. Most notable here is support for
Quantenna's QSR1000/QSR2000 chipsets and more flexible ways to provide
nvram files for brcmfmac.
Major changes:
brcmfmac
* add support for first trying to get a board specific nvram file
* add support for getting nvram contents from EFI variables
qtnfmac
* use single PCIe driver for all platforms and rename
Kconfig option CONFIG_QTNFMAC_PEARL_PCIE to CONFIG_QTNFMAC_PCIE
* add support for QSR1000/QSR2000 (Topaz) family of chipsets
ath10k
* add support for WCN3990 firmware crash recovery
* add firmware memory dump support for QCA4019
wil6210
* add firmware error recovery while in AP mode
ath9k
* remove experimental notice from dynack feature
iwlwifi
* PCI IDs for some new 9000-series cards
* improve antenna usage on connection problems
* new firmware debugging infrastructure
* some more work on 802.11ax
* improve support for multiple RF modules with 22000 devices
cordic
* move cordic macros and defines to a public header file
* convert brcmsmac and b43 to fully use cordic library
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcATmGAAoJEG4XJFUm622bk9kH/1RWa2z7Gmjr2wBSLHryvRAH
3FAUSJ4GJPH6MJ5X824srkcVsx2Y1RVt2i+bLXRXLq35aZkrFswohTXVM2h5dU7T
Uy2SL+q9pBUcS7fyv9bE7XV7KsFBJly/5p/wciVRZMnEK6X/w6KkBx/vGvlm5I/C
q196KazbVAYcl6s7KMrfFOYt0Wsto/gdEeesSVBkmcCTEkiKUjjJ4WEDVvAKK+qB
AiwgSdioqYmmEiUuredm6bhVqZG3K2mScoCy95N3jXkiDaKkaYgVtBuAU4Cdju/t
WgLIc9EnUYxXZtwnt889X62P1OkDOtKlj/mjdsGyF0Vrs1W+kErDO0NocOvu2Tk=
=9bL7
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-11-30' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.21
First set of patches for 4.21. Most notable here is support for
Quantenna's QSR1000/QSR2000 chipsets and more flexible ways to provide
nvram files for brcmfmac.
Major changes:
brcmfmac
* add support for first trying to get a board specific nvram file
* add support for getting nvram contents from EFI variables
qtnfmac
* use single PCIe driver for all platforms and rename
Kconfig option CONFIG_QTNFMAC_PEARL_PCIE to CONFIG_QTNFMAC_PCIE
* add support for QSR1000/QSR2000 (Topaz) family of chipsets
ath10k
* add support for WCN3990 firmware crash recovery
* add firmware memory dump support for QCA4019
wil6210
* add firmware error recovery while in AP mode
ath9k
* remove experimental notice from dynack feature
iwlwifi
* PCI IDs for some new 9000-series cards
* improve antenna usage on connection problems
* new firmware debugging infrastructure
* some more work on 802.11ax
* improve support for multiple RF modules with 22000 devices
cordic
* move cordic macros and defines to a public header file
* convert brcmsmac and b43 to fully use cordic library
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A new field was added. Since the code isn't operational (yet) no
need to worry about backward compatibility.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
FW debug data will oneshot read all data available in DRAM
and fill the supplied user buffer. In case the read request
is greater than the new data in DRAM, the driver will write
all data it has and return the buffer immediately.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Lior Cohen <lior2.cohen@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a function to be called when apply point occurs.
For each of the TLVs, the function will perform the
apply point logic:
- For HCMD - send the stored host command
- For buffer allocation - allocate the memory and send the
buffer allocation command
- For trigger and region - update the stored configuration
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When ini is loaded, disable all legacy trigger
configuration.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The new debug ini TLVs can be either packed into firmware
binary or written in external file. Support loading them
from both. Store the data per apply point. Apply point is
a point during driver runtime, where the TLV becomes active.
For example, a trigger of hardware error may be configured
to collect a subset of data pre-alive, as a opposed to HW
error that occurs after alive.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add the FW API of the new debug infrastructure. Next patches
will introduce the utilization of this infra.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We need to check the TWT support of the peer and to
propagte the capability to the firmware.
The current implementation will enable TWT only if the TWT
support is advertised in the HE CAP IE and in the Extended
Capability IE.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
FW dump was missing in case the RT FW ucode
section failed to load. This failure happens when
the RT section of the FW file is corrupted.
Signed-off-by: Lior Cohen <lior2.cohen@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware stopped looking at this field long ago.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Split the dump of RXF and TXF. This is in order to
enable code reuse for INI, which may decide to dump
only RXF and not TXF, and vice versa.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently opmode is limited to asking transport to either
dump all the dumps configured at startup, or monitor only.
Instead, pass to transport a bitmask, to allow flexibility.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the driver is unloaded when D3 debug data pulling is enabled
but not triggered, it doesn't release the data buffer.
Fix this by adding iwl_fw_runtime_free and calling it from the
relevant places.
Fixes: 2d8c261511 ("iwlwifi: add d3 debug data support")
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
From coreboot/BIOS:
Name ("WGDS", Package() {
Revision,
Package() {
DomainType, // 0x7:WiFi ==> We miss this one.
WgdsWiFiSarDeltaGroup1PowerMax1, // Group 1 FCC 2400 Max
WgdsWiFiSarDeltaGroup1PowerChainA1, // Group 1 FCC 2400 A Offset
WgdsWiFiSarDeltaGroup1PowerChainB1, // Group 1 FCC 2400 B Offset
WgdsWiFiSarDeltaGroup1PowerMax2, // Group 1 FCC 5200 Max
WgdsWiFiSarDeltaGroup1PowerChainA2, // Group 1 FCC 5200 A Offset
WgdsWiFiSarDeltaGroup1PowerChainB2, // Group 1 FCC 5200 B Offset
WgdsWiFiSarDeltaGroup2PowerMax1, // Group 2 EC Jap 2400 Max
WgdsWiFiSarDeltaGroup2PowerChainA1, // Group 2 EC Jap 2400 A Offset
WgdsWiFiSarDeltaGroup2PowerChainB1, // Group 2 EC Jap 2400 B Offset
WgdsWiFiSarDeltaGroup2PowerMax2, // Group 2 EC Jap 5200 Max
WgdsWiFiSarDeltaGroup2PowerChainA2, // Group 2 EC Jap 5200 A Offset
WgdsWiFiSarDeltaGroup2PowerChainB2, // Group 2 EC Jap 5200 B Offset
WgdsWiFiSarDeltaGroup3PowerMax1, // Group 3 ROW 2400 Max
WgdsWiFiSarDeltaGroup3PowerChainA1, // Group 3 ROW 2400 A Offset
WgdsWiFiSarDeltaGroup3PowerChainB1, // Group 3 ROW 2400 B Offset
WgdsWiFiSarDeltaGroup3PowerMax2, // Group 3 ROW 5200 Max
WgdsWiFiSarDeltaGroup3PowerChainA2, // Group 3 ROW 5200 A Offset
WgdsWiFiSarDeltaGroup3PowerChainB2, // Group 3 ROW 5200 B Offset
}
})
When read the ACPI data to find out the WGDS, the DATA_SIZE is never
matched.
From the above format, it gives 19 numbers, but our driver is hardcode
as 18.
Fix it to pass then can parse the data into our wgds table.
Then we will see:
iwlwifi 0000:01:00.0: U iwl_mvm_sar_geo_init Sending GEO_TX_POWER_LIMIT
iwlwifi 0000:01:00.0: U iwl_mvm_sar_geo_init SAR geographic profile[0]
Band[0]: chain A = 68 chain B = 69 max_tx_power = 54
iwlwifi 0000:01:00.0: U iwl_mvm_sar_geo_init SAR geographic profile[0]
Band[1]: chain A = 48 chain B = 49 max_tx_power = 70
iwlwifi 0000:01:00.0: U iwl_mvm_sar_geo_init SAR geographic profile[1]
Band[0]: chain A = 51 chain B = 67 max_tx_power = 50
iwlwifi 0000:01:00.0: U iwl_mvm_sar_geo_init SAR geographic profile[1]
Band[1]: chain A = 69 chain B = 70 max_tx_power = 68
iwlwifi 0000:01:00.0: U iwl_mvm_sar_geo_init SAR geographic profile[2]
Band[0]: chain A = 49 chain B = 50 max_tx_power = 48
iwlwifi 0000:01:00.0: U iwl_mvm_sar_geo_init SAR geographic profile[2]
Band[1]: chain A = 52 chain B = 53 max_tx_power = 51
Cc: stable@vger.kernel.org # 4.12+
Fixes: a6bff3cb19 ("iwlwifi: mvm: add GEO_TX_POWER_LIMIT cmd for geographic tx power table")
Signed-off-by: Matt Chen <matt.chen@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Logic is there twice, and we'll need a third place
soon for ini dumping. In addition move the dumping
to a function, also to enable reuse.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This enables to incorporate more logic in one place.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The trigger structure is being passed around, when
all we care about is whether to dump only monitor
or not. Pass a bool instead.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Debug data dump is not working in flows that stop the device is used
in their error handling. During these flows the op mode mutex is
locked until the device stops. Because of that, any assert generated
from the firmware can be handled only after the device already
stopped.
Since dumping cannot occour after stopping the device, split the the
dump function to two parts, Part that handles locking, and the part
that starts the actual dumping and call the second part in the op mode
stop device function.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As preparation for new trigger type, make iwl_fw_dbg_collect_desc
agnostic to the trigger structure.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwl_fw_dbg_collect can be called by any function that already
has the error string ready. iwl_fw_dbg_collect_trig, on the
other hand, does string formatting. The occurrences decrement
is at iwl_fw_dbg_collect_trig, instead of iwl_fw_dbg_collect,
which causes it to sometimes be skipped. Move it to the right
location.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As preparation for new trigger format, make the function
agnostic to the trigger fomat. Instead it gets the relevant
parameters - id and delay.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the info type is MU, we still have the data from the TSF
overload words, so should decode that. When it's MU_EXT_INFO
we additionally have the SIG-B common 0/1/2 fields.
Also document the validity depending on the info type and fix
the name of the regular TB PPDU info type accordingly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add debugfs to send host command in mvm and fmac op modes.
Allows to send host command at runtime via send_hcmd debugfs file.
The command is received as a string that represents hex values.
The struct of the command is as follows:
[cmd_id][flags][length][data]
cmd_id and flags are 8 chars long each.
length is 4 chars long.
data is length * 2 chars long.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add send host command op to firmware runtime op struct to allow sending
host commands to the op mode from the fw runtime context.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Change MCC update response API to be compatible with new FW API.
While at it change v2 which is not in use anymore to v3 and cleanup
mcc_update v1 command and response which is obsolete.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
With NICs that don't read the NVM directly and instead rely on getting
the relevant data from the firmware, the number of reserved MAC
addresses was not added to the API. This caused the driver to assume
there is only one address which results in all interfaces getting the
same address. Update the API to fix this.
While at it, fix-up the comments with firmware api names to actually
match what we have in the firmware.
Fixes: e9e1ba3dbf ("iwlwifi: mvm: support getting nvm data from firmware")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Trigger dump collection if the alive flow fails, regardless of the
reason.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The triplet of get trigger, is trigger enabled and is trigger stopped
repeats itself. Group them in a function to avoid code duplication.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The code that dumps various memory types repeats itself. Move it to a
function to avoid duplication.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Allow the FW to reorder HB channels and first scan HB channels with
assumed APs, in order to reduce the scan duration.
Currently enable it for all scan requests types.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Split iwl_fw_error_dump to two parts. The first part will dump the
actual data, and second will do the file allocations, trans calls and
actual file operations. This is done in order to enable reuse of the
code for the new debug ini infrastructure.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a macro to replace all the conditions checking for valid dump
length. In addition, move the fifo len calculation to a helper
function.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The debug variables are bloating the iwl_fw struct. And the fields
are out of order, missing docs and some are redundant.
Clean this up. This serves as preparation for unionizing it for the
new ini infra.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The capability bit was added to the driver and had been negotiated
with the firmware, but then got forgotten in the firmware and later
reused for a different capability. Now the firmware added it in a
new bit.
Fixes: 2eabc84d2f ("iwlwifi: mvm: only send LEDS_CMD when the FW supports it")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Annotate the compressed BA notification array sizes and
make both of them 0-length since the length of 1 is just
confusing - it may be different than that and the offset
to the second one needs to be calculated in the C code
anyhow.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to receive TB (Trigger Based) PPDU in monitor mode,
the Driver must send the HE_AIR_SNIFFER_CONFIG_CMD host command.
Enable that via debugfs.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We can dump data from the firmware either when it crashes,
or when the firmware is alive.
Not all the data is available if the firmware is running
(like the Tx / Rx FIFOs which are available only when the
firmware is halted), so we first check that the firmware
is alive to compute the required size for the dump and then
fill the buffer with the data.
When we allocate the buffer, we test the STATUS_FW_ERROR
bit to check if the firmware is alive or not. This bit
can be changed during the course of the dump since it is
modified in the interrupt handler.
We hit a case where we allocate the buffer while the
firmware is sill working, and while we start to fill the
buffer, the firmware crashes. Then we test STATUS_FW_ERROR
again and decide to fill the buffer with data like the
FIFOs even if no room was allocated for this data in the
buffer. This means that we overflow the buffer that was
allocated leading to memory corruption.
To fix this, test the STATUS_FW_ERROR bit only once and
rely on local variables to check if we should dump fifos
or other firmware components.
Fixes: 04fd2c2822 ("iwlwifi: mvm: add rxf and txf to dump data")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Cleanup of the debug flow by moving several flows to separate
functions to increase readability. Three functions were created:
1. iwl_fw_get_prph_len - returns the size needed for periphery dump.
2. iwl_fw_dump_mem for - executes the memory dumping flow.
3. iwl_trans_get_fw_monitor_len - returns the size needed for monitor dump.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no value in having an anonymous struct for holding
a few fields, remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In new devices, access to periphery is forbidden. Send instead
host command to start and stop debugging.
Memory allocation is written in context info, but in case we
need to update it there is a dedicated command. Add definitions,
currently unused, of the new command.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move the restart FW debug code to a function. This avoids code
duplication and lays the infra to support the new start and stop
host commands in some future devices.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The SP length in the ADD_STA command is an actual number of
frames, and not the SP len as it appears in the WME IE.
Fix that comment. The actual code is fine.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This reverts the addition of memory type in the memory debug TLV
as the firmware never ended up implementing it, and now the PRPH
dump is added as a different TLV.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case of fragmented scan on the HB channels, configure EBS to be
fragmented as well.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Decode the HE TB PPDU data that we get in sniffer mode
and use it to populate the HE radiotap information.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add flags to the tlc_cfg_cmd for signaling peer support for receiving
Dual Carrier Modulation at BPSK (MCS 0), and set them according to peer
capabilities.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the HE phy capabilities IE there are 2 bits to signal support for
STBC in bandwidths of 80Mhz or less, and of 160Mhz.
Use these bits to determine STBC support if this IE exists.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Make all FW debug data stop recording flows to use
iwl_fw_dbg_stop_recording function instead of writing to FW
registers directly.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Implement the extended HE-MU info type decoding to show the HE-SIG-B
common contents in the HE-MU radiotap field.
The DW4 data is partially overwritten by the hardware in all cases, so
only the higher 16 bits can be used. To be able to use it for the HE
SIG-B common data anyway, move the bits around in the following way:
SIG-B common 0: DW 4 -> DW 7
SIG-B common 1: DW 7 -> DW 8
SIG-B common 2: DW 8 -> DW 4 (upper half)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The Free Software Foundation address is superfluous and causes
checkpatch to issue a warning when present. Remove all paragraphs
with FSF's address to prevent that.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The new coex schema requires moving to SISO only when BT AG is 4.
Adjust the SISO criteria according to the coex schema version reported
by firmware.
Signed-off-by: Erel Geron <erelx.geron@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no point in warning here, the user will just get an
error back to the debugfs file write, and warning just makes
it seem like there's an internal consistency problem when in
reality the user just happened to hit this at a bad time.
Remove the warning.
Fixes: f45f979dc2 ("iwlwifi: mvm: disable dbg data collect when fw isn't alive")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Update reduce tx power command API to be compatible with new FW API.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
