Used for debugging what FW API we are using to understand misalignment
with API changes.
The output looks like this as a yaml format
fw_api_ver:
0x0001:
name: MVM_ALIVE
cmd_ver: 99
notif_ver: 4
0x0108:
name: PHY_CONTEXT_CMD
cmd_ver: 2
notif_ver: 0
...
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200424194456.18bf540ab8e0.I6217488f1740f0e6accd0cecd09dfd46bad88426@changeid
First set of patches for v5.8. Changes all over, ath10k apparently
seeing most new features this time. rtw88 also had lots of changes due
to preparation for new hardware support.
In this pull request there's also a new macro to include/linux/iopoll:
read_poll_timeout_atomic(). This is needed by rtw88 for atomic
polling.
Major changes:
ath11k
* add debugfs file for testing ADDBA and DELBA
* add 802.11 encapsulation offload on hardware support
* add htt_peer_stats_reset debugfs file
ath10k
* enable VHT160 and VHT80+80 modes
* enable radar detection in secondary segment
* sdio: disable TX complete indication to improve throughput
* sdio: decrease power consumption
* sdio: add HTT TX bundle support to increase throughput
* sdio: add rx bitrate reporting
ath9k
* improvements to AR9002 calibration logic
carl9170
* remove buggy P2P_GO support
p54usb
* add support for AirVasT USB stick
rtw88
* add support for antenna configuration
ti wlcore
* add support for AES_CMAC cipher
iwlwifi
* support for a few new FW API versions
* new hw configs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJetAhAAAoJEG4XJFUm622bADEH/A1OjAD3H1iZyTmXHP4T7yZe
TKJ+9I6B3BDR1czUTm+kUhrgBDNpdLLtu+b+5QXfpPLrtZ0FF/zjuazgueyqQpZ1
zudj+rG72njHpU0RKtO7wIBrCtckLPV0be+3026hztatJmJ7XQ9FvsanFPPsrrNv
0lh8E8kDUSynOW2me8FW1GBgDkGaBaicAs4FSjwNJC31Wo/VN5m9gEFkGpT1VJWP
l0xeEQ/N2mknQVuTR4CuMT9VJ0SNlJrLZpBVAqkmc170c3pKChl3LTNCnP925ye9
Nfqw2sQKgUPJKRbZR5wZTphGuu4krFv0ldWCvb0oFtZlCLIkiOz6+AA7b33oV2A=
=7ewK
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-05-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.8
First set of patches for v5.8. Changes all over, ath10k apparently
seeing most new features this time. rtw88 also had lots of changes due
to preparation for new hardware support.
In this pull request there's also a new macro to include/linux/iopoll:
read_poll_timeout_atomic(). This is needed by rtw88 for atomic
polling.
Major changes:
ath11k
* add debugfs file for testing ADDBA and DELBA
* add 802.11 encapsulation offload on hardware support
* add htt_peer_stats_reset debugfs file
ath10k
* enable VHT160 and VHT80+80 modes
* enable radar detection in secondary segment
* sdio: disable TX complete indication to improve throughput
* sdio: decrease power consumption
* sdio: add HTT TX bundle support to increase throughput
* sdio: add rx bitrate reporting
ath9k
* improvements to AR9002 calibration logic
carl9170
* remove buggy P2P_GO support
p54usb
* add support for AirVasT USB stick
rtw88
* add support for antenna configuration
ti wlcore
* add support for AES_CMAC cipher
iwlwifi
* support for a few new FW API versions
* new hw configs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add framework for supporting specific PHY filter configuration,
which allows for application of various FW defined PHY filters
(one per antenna). Change phy_cfg_cmd to the new API (ver3).
Reading of configuration from platform's ACPI tables to be added
later when tables are defined.
Signed-off-by: Gil Adam <gil.adam@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200418110539.242a8f979592.I13c77a8a8dbf1a169b5052c7af1f8401ff3991ad@changeid
Add support for the new WOWLAN_GET_STATUS notification that contains a
new element that informs the driver of TIDs whose BA sessions were
closed during suspend.
Note that the new functionality of handling these closed sessions is not
implemented in this patch it. It only aligns to the new API version.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200417131727.b02153b94c1d.Ieb6291586d60f372d5a505604b18227ef97e7202@changeid
The API version lookup is parsed from a TLV and should be in shared code
make make it reusable across all opmodes.
Also change the function names from mvm to fw, since this is not
mvm-specific anymore.
Additionally, since this function is not just a single line of code, it
shouldn't be inline. Convert them to actual functions.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200421133326.cf94672dfcdb.I5ede9cc25ee8de7b8d2b5c574f917a18971da734@changeid
Due to some hardware issues, queue 31 isn't usable on devices that have
32 queues (7000, 8000, 9000 families), which is correctly reflected in
the configuration and TX queue initialization.
However, the firmware API and queue allocation code assumes that there
are 32 queues, and if something actually attempts to use #31 this leads
to a NULL-pointer dereference since it's not allocated.
Fix this by limiting to 31 in the IWL_MVM_DQA_MAX_DATA_QUEUE, and also
add some code to catch this earlier in the future, if the configuration
changes perhaps.
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20200417100405.98a79be2db6a.I3a4af6b03b87a6bc18db9b1ff9a812f397bee1fc@changeid
Third set of patches for v5.7. Nothing really special this time,
business as usual.
When pulling this to net-next there's again a conflict in:
drivers/net/wireless/intel/iwlwifi/pcie/drv.c
To solve this drop these three lines from the conflict (the first hunk
from "HEAD") as the whole AX200 block was moved above in the same
file:
IWL_DEV_INFO(0x2723, 0x1653, iwl_ax200_cfg_cc, iwl_ax200_killer_1650w_name),
IWL_DEV_INFO(0x2723, 0x1654, iwl_ax200_cfg_cc, iwl_ax200_killer_1650x_name),
IWL_DEV_INFO(0x2723, IWL_CFG_ANY, iwl_ax200_cfg_cc, iwl_ax200_name),
And keep all the __IWL_DEV_INFO() entries (the second hunk). In other
words, take everything from wireless-drivers-next. When running 'git
diff' after the resolution the output should be empty.
Major changes:
brcmfmac
* add USB autosuspend support
ath11k
* handle RX fragments
* enable PN offload
* add support for HE BSS color
iwlwifi
* support new FW API version
* support for EDCA measurements
* new scan API features
* enable new firmware debugging code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJefdsZAAoJEG4XJFUm622blekH/2fIoUtl8Kdih38hNjz63PLD
x+LCPjZdRjrmFGTSxnS1rZiIM7v2yXyLGiyq+yr2ltzkpTi8xWOkKL6US8RCew9R
otRtZyLrhgMLG2ExDna1fI5ZJAtLnxV31TCy6yrSUDZ8t4VxMNIB4si3WRzKvAfU
c+cQcsnWr+pCDnbxh53BcYIyiEqKlttw/fGuIKchKuYMQy7DV6nxMdTaAym5Szzi
Nlb8fhXWFaPrPQ6NtHb5WWm4Er3wtMzN/AG8aFVxjrik07vTxQKWamdT9CeK2tDT
iDbx2HaNCWFMulXeZMrc9+inoAzj3UjbPqH3OTUk9iHbVA0unc3CdEBFD9h928Q=
=D/FA
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-03-27' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.7
Third set of patches for v5.7. Nothing really special this time,
business as usual.
When pulling this to net-next there's again a conflict in:
drivers/net/wireless/intel/iwlwifi/pcie/drv.c
To solve this drop these three lines from the conflict (the first hunk
from "HEAD") as the whole AX200 block was moved above in the same
file:
IWL_DEV_INFO(0x2723, 0x1653, iwl_ax200_cfg_cc, iwl_ax200_killer_1650w_name),
IWL_DEV_INFO(0x2723, 0x1654, iwl_ax200_cfg_cc, iwl_ax200_killer_1650x_name),
IWL_DEV_INFO(0x2723, IWL_CFG_ANY, iwl_ax200_cfg_cc, iwl_ax200_name),
And keep all the __IWL_DEV_INFO() entries (the second hunk). In other
words, take everything from wireless-drivers-next. When running 'git
diff' after the resolution the output should be empty.
Major changes:
brcmfmac
* add USB autosuspend support
ath11k
* handle RX fragments
* enable PN offload
* add support for HE BSS color
iwlwifi
* support new FW API version
* support for EDCA measurements
* new scan API features
* enable new firmware debugging code
====================
Kalle gave me directions on how to resolve the iwlwifi conflict
as follows:
====================
When pulling this to net-next there's again a conflict in:
drivers/net/wireless/intel/iwlwifi/pcie/drv.c
To solve this drop these three lines from the conflict (the first hunk
from "HEAD") as the whole AX200 block was moved above in the same
file:
IWL_DEV_INFO(0x2723, 0x1653, iwl_ax200_cfg_cc, iwl_ax200_killer_1650w_name),
IWL_DEV_INFO(0x2723, 0x1654, iwl_ax200_cfg_cc, iwl_ax200_killer_1650x_name),
IWL_DEV_INFO(0x2723, IWL_CFG_ANY, iwl_ax200_cfg_cc, iwl_ax200_name),
And keep all the __IWL_DEV_INFO() entries (the second hunk). In other
words, take everything from wireless-drivers-next. When running 'git
diff' after the resolution the output should be empty.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is used to initialize the default value, but refers back
to the value itself, essentially leading to a
val = val
assignment at init time ... that's useless, remove it and use
_NODEF.
Change-Id: I725923016563c34ce2fa057bf7c12984e1041c49
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The FW changed the maximum number of scan offload profiles to 8 in new
APIs. Support it by changing the scan_offload_profile_cfg struct to be
more dynamic, so we can reuse most of the code and only change size of
the profiles array.
Change-Id: I65210cf541af46e2675a8c764d5871f7f5b070d6
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we have an assert during D3 we want to dump the internal
buffer memory even if are we working in DRAM debug mode. We should not
block dumping it.
Change-Id: I69aad2d4904c4f8bb653c61e8781a2e07780054f
Signed-off-by: Rotem Saado <rotem.saado@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This new command is mostly backwards compatible, with the exception
that the device_type element was changed into a bitmask. The device
type bit remains the same (because we only had 0 and 1 anyway), but
when using v1 we can't set any other bits, because that would change
the integer.
Other than that, the struct remains the same and the driver can set
the device_type bit in both cases, but it can only set the low_latency
bit if VER_2 is used.
Change-Id: Ib68d4c821ebcce253b42ed0ea15881fb4e3e01da
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Modify adaptive dwell number of APs override API
Instead of using channel to index mapping, add the adaptive dwell
override parameters as part of the configuration per channel in the scan
request command.
Support 2 different override values and use them as follows:
1. 10 APs for friendly GO channels in p2p scan.
2. 2 APs for social channels in p2p scan.
Change-Id: I3b461108abf2306c3d054099112f2c3afce1cc92
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a new region type that allows us to dump the PCI config space.
This is mostly the same as dumping a memory region, but reading from
the device's config space instead.
In order to make this generic and independent of the trans type, we
make a function called iwl_dump_ini_config_iter() that calls a new op
in the transport to read its config space.
Change-Id: I15151bddf589f13b0e0a45c28b96bbcd73bcfdeb
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some devices require longer time to stabilize the power and XTAL.
This is especially true for devices integrated in the SoC. Add
support for a new firmware API that allows the driver to set the
latency value accordingly.
Change-Id: I6829a46b89e4e701f80a0e4033f4dd41ee44ed12
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The GEO_TX_POWER_LIMIT command was sent although
there is no wgds table, so the fw got wrong SAR values
from the driver.
Fix this by avoiding sending the command if no wgds
tables are available.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Fixes: 39c1a9728f ("iwlwifi: refactor the SAR tables from mvm to acpi")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Tested-By: Jonathan McDowell <noodles@earth.li>
Tested-by: Len Brown <len.brown@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20200318081237.46db40617cc6.Id5cf852ec8c5dbf20ba86bad7b165a0c828f8b2e@changeid
If the firmware is in a bad state or not initialized fully, sending
the DBGC_SUSPEND_RESUME command fails but we can still collect logs.
Instead of aborting the entire dump process, simply ignore the error.
By removing the last callpoint that was checking the return value, we
can also convert the function to return void.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fixes: 576058330f ("iwlwifi: dbg: support debug recording suspend resume command")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200306151129.dcec37b2efd4.I8dcd190431d110a6a0e88095ce93591ccfb3d78d@changeid
The TLV offset is only used to read registers, while the offset used for
the FIFO addresses are hard coded in the driver and not given by the
TLV.
If we try to apply the TLV offset when reading the FIFOs, we'll read
from invalid addresses, causing the driver to hang.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Fixes: 8d7dea25ad ("iwlwifi: dbg_ini: implement Rx fifos dump")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200306151129.fbab869c26fa.I4ddac20d02f9bce41855a816aa6855c89bc3874e@changeid
Second set of patches for v5.6. Nothing special standing out, smaller
new features and fixes allover.
Major changes:
ar5523
* add support for SMCWUSBT-G2 USB device
iwlwifi
* support new versions of the FTM FW APIs
* support new version of the beacon template FW API
* print some extra information when the driver is loaded
rtw88
* support wowlan feature for 8822c
* add support for WIPHY_WOWLAN_NET_DETECT
brcmfmac
* add initial support for monitor mode
qtnfmac
* add module parameter to enable DFS offloading in firmware
* add support for STA HE rates
* add support for TWT responder and spatial reuse
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJeLcWsAAoJEG4XJFUm622bDGUIAJuhM4LiDAzOGnDjH5cMosOC
/qwDpGD19cEeVAhNSMKUn7Uo9+qbQYIleiO7XXxzCuJceYbxbT5s3Vb/fWsRUPjS
cBDmGuK8/giqMQJshXvfCTsoF83CyirCjY/MJvomK2BRlXM8hQ3s6hAcfU0zQ96e
OU1akcfZzUwjaBKaDYLncxLuGbeUXMy8AZwFdgQlQRMoObpen/IIwx6jDK/A+3l6
VCOJF+JTkDytfNWmTpZ65uJrYEXoLe6G4028FjOI4BDFmEgvdHC5vTm7VOBhrkuB
9tsKcYNvECCNn2WI96V+etD8kaZPscQIW8hgOrYyGxw43lJg5zH4Z9eWAmHojxE=
=UOhb
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-01-26' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.6
Second set of patches for v5.6. Nothing special standing out, smaller
new features and fixes allover.
Major changes:
ar5523
* add support for SMCWUSBT-G2 USB device
iwlwifi
* support new versions of the FTM FW APIs
* support new version of the beacon template FW API
* print some extra information when the driver is loaded
rtw88
* support wowlan feature for 8822c
* add support for WIPHY_WOWLAN_NET_DETECT
brcmfmac
* add initial support for monitor mode
qtnfmac
* add module parameter to enable DFS offloading in firmware
* add support for STA HE rates
* add support for TWT responder and spatial reuse
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We have a lot of mostly duplicated data structures that are repeated
only because the device name string is different. To avoid this, move
the string from the cfg to the trans structure and add it
independently from the rest of the configuration to the PCI mapping
tables.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We have many different firmware images with the same version,
and it's sometimes cumbersome to figure out which image was
really used, especially as the marketing strings that we do
print out can be the same for (slightly) different hardware
using different firmware images.
Incorporate the firmware filename into the fw_version so it's
printed out all the time. Unfortunately, this will make the
string be longer than the 32 characters for ethtool, but we
almost never really use ethtool, so strip the "iwlwifi-"
prefix (if not overridden), and the remaining data that may
then be stripped at the end is not usually useful anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Now that we don't have dynamically changing domains anymore, we can
simply skip all the TLVs with domains that are not enabled. To do so,
remove the checks from the functions that handle the TLVs when a
timepoint is reached to the top allocation function.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Now that we can't change the domain at runtime anymore, we don't have
to protect the active trigger status. Remove it. Additionally, we
don't need to flush the dumps at this point anymore, since this only
runs during initialization and there shouldn't be any dumps running.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't want to allow changing the domain via debugfs so that we can
apply the domain to all TLV types more easily (doing some at runtime
is difficult due to buffer allocations etc.). Change the
fw_dbg_domain debugfs file to be read-only and remove the write
function.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The new API version adds support for FILS discovery frames.
It adds a new flag and a field for short SSID configuration.
The new API is backward compatible, so we can just switch to it.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the for loop where we are supposed to go through the entire table,
we are using a non-static local to keep the pos index. This makes
each iteration start with 3, so we always access the first item on the
table. Fix this by moving the variable outside of the loo so it
doesn't lose its value at every iteration.
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fixes: ba3224db78 ("iwlwifi: mvm: fix an out-of-bound access")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The driver is required to stop the debug monitor HW recording regardless
of the debug configuration since the driver is responsible to halt the
FW DBGC.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The new API requires the driver to config the supported frame format
(legacy, HT, VHT etc.).
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The new API requires the driver to set the frame format
(legacy, HT, VHT etc.) to be used for the measurement.
The new API also supports 11az and secured measurement, but
these are not supported by the driver for now.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The fw already support scan api v12,
v11 is not needed anymore.
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Before we start looping over the internal TX FIFOs increase the fifo
number, but that's incorrect and causes a FIFO to be skipped. This is
probably due to a copy and paste from the previous loop.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
1. Modify channel config flags to be used for legacy bands channels
as well, to indicate SSIDs elements from ssidIEsArray.
2. Add new general flag.
3. Remove ssidNum from probe params.
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This is dead code, nothing uses the IWL_DEVICE_22560 macro and
thus nothing every uses IWL_DEVICE_FAMILY_22560. Remove it all.
While at it, remove some code and definitions used only in this
case, and clean up some comments/names that still refer to it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware API has changed a little bit but this change
has no impact on the flow and is backward compatible.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Refactored the SAR related functions from iwlmvm to acpi
in order to make it shared between different opmodes
in addition to removing unused variable ppag_rev.
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Implement scan request command version 12.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Implement a new versioning handling flow supported from version 11
onwards.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add a reference to the correct enum rather than showing
the pattern of the actual constants.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FW scan api ver 11 adds support for some new features,
in this version the fw did also some cleanup in the api,
which causes the driver not to be able to use the
current scan req struct.
Therefore, in this patch the driver has new version for the scan command
code
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
First set of patches for 5.5. The most active driver here clearly is
rtw88, lots of patches for it. More quiet on other drivers, smaller
fixes and cleanups all over.
This pull request also has a trivial conflict, the report and example
resolution here:
https://lkml.kernel.org/r/20191031111242.50ab1eca@canb.auug.org.au
Major changes:
rtw88
* add deep power save support
* add mac80211 software tx queue (wake_tx_queue) support
* enable hardware rate control
* add TX-AMSDU support
* add NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 support
* add power tracking support
* add 802.11ac beamformee support
* add set_bitrate_mask support
* add phy_info debugfs to show Tx/Rx physical status
* add RFE type 3 support for 8822b
ath10k
* add support for hardware rfkill on devices where firmware supports it
rtl8xxxu
* add bluetooth co-existence support for single antenna
iwlwifi
* Revamp the debugging infrastructure
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdwYyqAAoJEG4XJFUm622b/jMH/0KUcGz8y4gkk2B2lMRyUOTu
t84LiSHxcsq6letlr/vak4S6NrxMLP8Z/ByyoKC8o3yeVsdyMNMSLZAztFFhxdXr
Haky2SM10q6vnn9s1skXS/qkHSd2WdUFT2DgYxyOPCtJUazVKjcboJ4YX/TUg99a
5eqPpZ4RXtW6uOmWHS7JXtLcCFPywKPBtMAjLEDMYOUSSBWExBNyNZNhznSS3ywY
4VKvc675gXE+WD3qXRhL8EJjyed94yuS3wYbKWp8iTaIRyluDmc5lVhjWH1A0HLE
Qb62QL8XLtbX5fcTnaupdAIXwxeIBylOBe8QtW7QUbAnGFf8bexLxfnQM+To4wI=
=24zD
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2019-11-05' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.5
First set of patches for 5.5. The most active driver here clearly is
rtw88, lots of patches for it. More quiet on other drivers, smaller
fixes and cleanups all over.
This pull request also has a trivial conflict, the report and example
resolution here:
https://lkml.kernel.org/r/20191031111242.50ab1eca@canb.auug.org.au
Major changes:
rtw88
* add deep power save support
* add mac80211 software tx queue (wake_tx_queue) support
* enable hardware rate control
* add TX-AMSDU support
* add NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 support
* add power tracking support
* add 802.11ac beamformee support
* add set_bitrate_mask support
* add phy_info debugfs to show Tx/Rx physical status
* add RFE type 3 support for 8822b
ath10k
* add support for hardware rfkill on devices where firmware supports it
rtl8xxxu
* add bluetooth co-existence support for single antenna
iwlwifi
* Revamp the debugging infrastructure
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The API was reduced to include only knowledge currently needed by the
FW scan logic, the rest is legacy. Support the new, reduced version.
Using the old API with newer firmwares (starting from
iwlwifi-*-50.ucode, which implements and requires the new API version)
causes an assertion failure similar to this one:
[ 2.854505] iwlwifi 0000:00:14.3: 0x20000038 | BAD_COMMAND
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The FW introduce new API to get the band from the rx mpdu,
use this new API.
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
During dump flow, the driver allocates spaces to store the memory
regions that will be included in the dump. These regions can be very
large so in order to avoid allocation failure, use vzalloc instead.
The kmalloc uses GFP_KERNEL and the driver does not make any use of the
fact that the memory is contiguous so the same functionality is
maintained.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A missed VAP notification will be sent from umac when
the station is out of sync with its associated non-transmitted
BSSID. The notification will be sent only if the transmitted
BSSID is an EMA-AP one.
The driver will consider this notification as connection loss.
Signed-off-by: Lior Cohen <lior2.cohen@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware has now a new session protection command.
This new API allows the firmware to manage the protection
needed for association. It'll also remove the event when
the association is complete.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
During D3 state there are some flows which requires FW reset.
Add new API to support it.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Remove unused code of the old debug ini API.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Allow the driver to collect FW response/notification region type
during dump and allow triggering dump collection for a given FW
response/notification.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Allow to change or read the debug domain bitmap at runtime via
fw_dbg_domain debugfs.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Calculate active triggers list and implement time points handling.
Also allow to override the debug domain via iwl-dbg-cfg.ini by setting
FW_DBG_DOMAIN field.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add new debug TLVs API preprocessing.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Make dump info region use new API.
debug_info_tlv_list list will be initialize in a future patch once the
driver will start using it.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Allow to collect error table data.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Allow collecting monitor data in ini debug mode.
Implement both SMEM and DRAM monitor regions dumping.
For DRAM monitor, support DBGC1, DBGC2 and DBGC3 and support several
DRAM fragments per DBGC.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Make dump flow use the new trigger TLV.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Make dump flow use the new region TLV and update the region type enum.
Temporarily remove monitor dumping support. Support will be readded in a
future patch.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In alloc_sgtable if alloc_page fails, the alocated table should be
released.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We can't check for the ACPI table revision validity in the same if
where we check if the package was read correctly, because we return
PTR_ERR(pkg) and if the table is not valid but the pointer is, we
would return a valid pointer as an error. Fix that by moving the
table checks to a separate if and return -EINVAL if it's not valid.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Use cancel_delayed_work_sync on the dump workers only in case of
unloading the op mode. In any other case use iwl_fw_flush_dumps or
iwl_fw_dbg_stop_sync (depends if the op mode mutex is held or not).
This way, the driver will wait until debug data is collected in all
cases but op mode unloading.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Remove periodic trigger functionality.
After moving to the new API we will add periodic trigger functionality
that matches the new API.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fix the documentation of struct iwl_fw_ini_monitor_dump and
iwl_fw_ini_error_dump_range.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support code to be able to use the DRAM buffer allocation command,
which allows us to send information about a buffer to the firmware
to use it with the DBGC hardware.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Remove the "apply points" mechanism as preparation for the changed
debug API where this is now a "time point" instead. Use a new API
across the code at the trigger points ("time points"), but don't
yet implement it since that requires some more preparation.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Allows to easily calculate array length at the end of a TLV.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are products which have a single chain with 2 antennas.
In these products, we need to inform the FW that the device has the
single antenna diversity(SAD) feature. In the future, we will read
the active antenna from a BIOS configuration. Currently, we use a
default configuration which means that the FW decides which antenna to use.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In prior hardware generations (e.g. 9000 series), we received the BAR
frame with fake NSSN information to handle releasing frames from the
reorder buffer for the default queue, the other queues were getting
the FRAME_RELEASE notification in this case.
With multi-TID block-ack, the firmware no longer sends us the BAR
frame because the fake RX is quite big (just the metadata is around
48 bytes or so). Instead, it now sends us one (or multiple) special
release notifications (0xc2). The hardware consumes these as well,
but only generates the FRAME_RELEASE (0xc3) for queues other than
the default queue. We thus need to handle them in the same way we
handle the normal FRAME_RELEASE.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
WoWlan feature within the FW uses the station id for various of reasons.
Thus we need to add this information to the command.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a pointer to the iwl_trans structure and point it to the trans
part of the cfg. This is the first step in disassociating the trans
configuration from the rest of the configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to be able to select the cfg depending on the HW revision or
on the RF ID, we need to set up the trans before selecting the cfg.
To do so, move the elements from cfg that are needed by
iwl_trans_alloc() to a separate struct at the top of the cfg, so it
can be used by other cfg types as well, before selecting the rest of
the configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Make a static regions ops array and use it instead of switch case when
determining what op to use to collect a region.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Avoid iterating over dump TLVs twice for size calculation by using
linked list to store the dump TLVs.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
separate configuration flows and dump collection flows.
make ini configuration flows be in iwl-dbg-tlv.c and dump related flows
in dbg.c to better reflect their logical difference.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Align wrt log prints to the driver coding style
Remove the ext field from the log and print it at the beginning of the
apply point.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Debug flow TLV was removed from the FW. Remove the TLV from the driver
as well.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Reimplement debug TLV allocation flow. The driver will check the
validity of the debug TLVs prior allocating space for them.
Any malformed or unsupported TLV will be skipped.
The TLV specific checks will be added in later patches.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
use iwl_trans_dbg_ini_valid function instead of a boolean value check if
dbg_ini mode is on. It is needed for a future patch.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The real name is struct iwl_tof_range_req_ext_cmd, fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
TX power limits as defined in the OTP assume the worst case scenario
in terms of the platform's atenna gain, but most platforms are below
that value so they can use more TX power without passing the regulatory
limit. If the platform indicates in the BIOS that it indeed has lower
gain, and the geographic location allows it, higher TX power can be
used. The driver reads the PPAG (Per-Platform Antenna Gain) data from
BIOS (if it exists), validates it and sends the appropriate command to
the FW. This flow happens once at FW init, in case of suspend/resume
there is no need to read again from BIOS as we save those values during
init, so just send the PPAG command again to FW.
Signed-off-by: Gil Adam <gil.adam@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
dma_alloc_coherent is not just the page allocator. The only valid
arguments to pass are either GFP_ATOMIC or GFP_ATOMIC with possible
modifiers of __GFP_NORETRY or __GFP_NOWARN.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
periphery phy and aux regions should not be collected like periphery mac
region. Remove their handling. The handling will be added in the future
once the FW will support it.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: 7a14c23dcd ("iwlwifi: dbg: dump data according to the new ini TLVs")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Use a linked list to maintain the debug TLVs instead of a single buffer.
This way, the driver does not need to iterate over the binary file twice
and allocates smaller chunks of memory. Also, in case one allocation
fails the driver will work with the partial configuration instead of
aborting the entire debug configuration.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Maintain DRAM debug buffer status in trans instead of keeping it as
part of the TLVs buffer to avoid allocating extra space for it.
Needed for future changes.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
