Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 3ced0a88cd ("qlcnic: Add support to run firmware POST")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1605248186-16013-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pm_runtime_get_sync() will increment pm usage at first and it will
resume the device later. If runtime of the device has error or
device is in inaccessible state(or other error state), resume
operation will fail. If we do not call put operation to decrease
the reference, it will result in reference count leak. Moreover,
this device cannot enter the idle state and always stay busy or other
non-idle state later. So we fixed it by replacing it with
pm_runtime_resume_and_get.
Fixes: 8fff755e9f ("net: fec: Ensure clocks are enabled while using mdio bus")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the phy enables power saving technology, the dwmac's software reset
needs more time to complete, enlarge dma reset timeout to 200000us.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20201113090902.5c7aab1a@xhacker.debian
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On arm imx6, when opening the chip's netdev, the whole Linux
kernel intermittently hangs/freezes.
This is caused by a bug in the driver code which tests if pcie
interrupts are working correctly, using the software interrupt:
1. open: enable the software interrupt
2. open: tell the chip to assert the software interrupt
3. open: wait for flag
4. ISR: acknowledge s/w interrupt, set flag
5. open: notice flag, disable the s/w interrupt, continue
Unfortunately the ISR only acknowledges the s/w interrupt, but
does not disable it. This will re-trigger the ISR in a tight
loop.
On some (lucky) platforms, open proceeds to disable the s/w
interrupt even while the ISR is 'spinning'. On arm imx6,
the spinning ISR does not allow open to proceed, resulting
in a hung Linux kernel.
Fix minimally by disabling the s/w interrupt in the ISR, which
will prevent it from spinning. This won't break anything because
the s/w interrupt is used as a one-shot interrupt.
Note that this is a minimal fix, overlooking many possible
cleanups, e.g.:
- lan743x_intr_software_isr() is completely redundant and reads
INT_STS twice for no apparent reason
- disabling the s/w interrupt in lan743x_intr_test_isr() is now
redundant, but harmless
- waiting on software_isr_flag can be converted from a sleeping
poll loop to wait_event_timeout()
Fixes: 23f0703c12 ("lan743x: Add main source files for new lan743x driver")
Tested-by: Sven Van Asbroeck <thesven73@gmail.com> # arm imx6 lan7430
Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com>
Link: https://lore.kernel.org/r/20201112204741.12375-1-TheSven73@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When running this chip on arm imx6, we intermittently observe
the following kernel warning in the log, especially when the
system is under high load:
[ 50.119484] ------------[ cut here ]------------
[ 50.124377] WARNING: CPU: 0 PID: 303 at kernel/softirq.c:169 __local_bh_enable_ip+0x100/0x184
[ 50.132925] IRQs not enabled as expected
[ 50.159250] CPU: 0 PID: 303 Comm: rngd Not tainted 5.7.8 #1
[ 50.164837] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[ 50.171395] [<c0111a38>] (unwind_backtrace) from [<c010be28>] (show_stack+0x10/0x14)
[ 50.179162] [<c010be28>] (show_stack) from [<c05b9dec>] (dump_stack+0xac/0xd8)
[ 50.186408] [<c05b9dec>] (dump_stack) from [<c0122e40>] (__warn+0xd0/0x10c)
[ 50.193391] [<c0122e40>] (__warn) from [<c0123238>] (warn_slowpath_fmt+0x98/0xc4)
[ 50.200892] [<c0123238>] (warn_slowpath_fmt) from [<c012b010>] (__local_bh_enable_ip+0x100/0x184)
[ 50.209860] [<c012b010>] (__local_bh_enable_ip) from [<bf09ecbc>] (destroy_conntrack+0x48/0xd8 [nf_conntrack])
[ 50.220038] [<bf09ecbc>] (destroy_conntrack [nf_conntrack]) from [<c0ac9b58>] (nf_conntrack_destroy+0x94/0x168)
[ 50.230160] [<c0ac9b58>] (nf_conntrack_destroy) from [<c0a4aaa0>] (skb_release_head_state+0xa0/0xd0)
[ 50.239314] [<c0a4aaa0>] (skb_release_head_state) from [<c0a4aadc>] (skb_release_all+0xc/0x24)
[ 50.247946] [<c0a4aadc>] (skb_release_all) from [<c0a4b4cc>] (consume_skb+0x74/0x17c)
[ 50.255796] [<c0a4b4cc>] (consume_skb) from [<c081a2dc>] (lan743x_tx_release_desc+0x120/0x124)
[ 50.264428] [<c081a2dc>] (lan743x_tx_release_desc) from [<c081a98c>] (lan743x_tx_napi_poll+0x5c/0x18c)
[ 50.273755] [<c081a98c>] (lan743x_tx_napi_poll) from [<c0a6b050>] (net_rx_action+0x118/0x4a4)
[ 50.282306] [<c0a6b050>] (net_rx_action) from [<c0101364>] (__do_softirq+0x13c/0x53c)
[ 50.290157] [<c0101364>] (__do_softirq) from [<c012b29c>] (irq_exit+0x150/0x17c)
[ 50.297575] [<c012b29c>] (irq_exit) from [<c0196a08>] (__handle_domain_irq+0x60/0xb0)
[ 50.305423] [<c0196a08>] (__handle_domain_irq) from [<c05d44fc>] (gic_handle_irq+0x4c/0x90)
[ 50.313790] [<c05d44fc>] (gic_handle_irq) from [<c0100ed4>] (__irq_usr+0x54/0x80)
[ 50.321287] Exception stack(0xecd99fb0 to 0xecd99ff8)
[ 50.326355] 9fa0: 1cf1aa74 00000001 00000001 00000000
[ 50.334547] 9fc0: 00000001 00000000 00000000 00000000 00000000 00000000 00004097 b6d17d14
[ 50.342738] 9fe0: 00000001 b6d17c60 00000000 b6e71f94 800b0010 ffffffff
[ 50.349364] irq event stamp: 2525027
[ 50.352955] hardirqs last enabled at (2525026): [<c0a6afec>] net_rx_action+0xb4/0x4a4
[ 50.360892] hardirqs last disabled at (2525027): [<c0d6d2fc>] _raw_spin_lock_irqsave+0x1c/0x50
[ 50.369517] softirqs last enabled at (2524660): [<c01015b4>] __do_softirq+0x38c/0x53c
[ 50.377446] softirqs last disabled at (2524693): [<c012b29c>] irq_exit+0x150/0x17c
[ 50.385027] ---[ end trace c0b571db4bc8087d ]---
The driver is calling dev_kfree_skb() from code inside a spinlock,
where h/w interrupts are disabled. This is forbidden, as documented
in include/linux/netdevice.h. The correct function to use
dev_kfree_skb_irq(), or dev_kfree_skb_any().
Fix by using the correct dev_kfree_skb_xxx() functions:
in lan743x_tx_release_desc():
called by lan743x_tx_release_completed_descriptors()
called by in lan743x_tx_napi_poll()
which holds a spinlock
called by lan743x_tx_release_all_descriptors()
called by lan743x_tx_close()
which can-sleep
conclusion: use dev_kfree_skb_any()
in lan743x_tx_xmit_frame():
which holds a spinlock
conclusion: use dev_kfree_skb_irq()
in lan743x_tx_close():
which can-sleep
conclusion: use dev_kfree_skb()
in lan743x_rx_release_ring_element():
called by lan743x_rx_close()
which can-sleep
called by lan743x_rx_open()
which can-sleep
conclusion: use dev_kfree_skb()
Fixes: 23f0703c12 ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com>
Link: https://lore.kernel.org/r/20201112185949.11315-1-TheSven73@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We always have to update the value of ret, otherwise the
error value may be the previous one.
Fixes: f6bd59526c ("net: ethernet: ti: introduce am654 common platform time sync driver")
Signed-off-by: Wang Qing <wangqing@vivo.com>
[grygorii.strashko@ti.com: fix build warn, subj add fixes tag]
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20201112164541.3223-1-grygorii.strashko@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 4c2703dfd7 ("net: marvell: prestera: Add PCI interface support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Reviewed-by: Vadym Kochan <vadym.kochan@plvision.eu>
Acked-by: Vadym Kochan <vadym.kochan@plvision.eu>
Link: https://lore.kernel.org/r/20201113113236.71678-1-wanghai38@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Depending on the SoC/platform the CPSW can completely lose context after a
suspend/resume cycle, including CPSW wrapper (WR) which will cause reset of
WR_C0_MISC_EN register, so CPTS IRQ will became disabled.
Fix it by moving CPTS IRQ enabling in cpsw_ndo_open() where CPTS is
actually started.
Fixes: 84ea9c0a95 ("net: ethernet: ti: cpsw: enable cpts irq")
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20201112111546.20343-1-grygorii.strashko@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 8c7bd5a454 ("net: ethernet: mtk-star-emac: new driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/1605180879-2573-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ndo_start_xmit() method must return NETDEV_TX_OK if the DMA mapping
fails, after freeing the socket buffer.
Fix the mtk_star_netdev_start_xmit() function accordingly.
Fixes: 8c7bd5a454 ("net: ethernet: mtk-star-emac: new driver")
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20201112084833.21842-1-vincent.stehle@laposte.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When no devicetree is present, the driver will use an
uninitialized variable.
Fix by initializing this variable.
Fixes: 902a66e08c ("lan743x: correctly handle chips with internal PHY")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com>
Link: https://lore.kernel.org/r/20201112152513.1941-1-TheSven73@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2020-11-10
This series contains updates to i40e and igc drivers and the MAINTAINERS
file.
Slawomir fixes updating VF MAC addresses to fix various issues related
to reporting and setting of these addresses for i40e.
Dan Carpenter fixes a possible used before being initialized issue for
i40e.
Vinicius fixes reporting of netdev stats for igc.
Tony updates repositories for Intel Ethernet Drivers.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
MAINTAINERS: Update repositories for Intel Ethernet Drivers
igc: Fix returning wrong statistics
i40e, xsk: uninitialized variable in i40e_clean_rx_irq_zc()
i40e: Fix MAC address setting for a VF via Host/VM
====================
Link: https://lore.kernel.org/r/20201111001955.533210-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stop the queue and ask for the credits if queue reaches to
threashold.
Fixes: 5a4b9fe7fe ("cxgb4/chcr: complete record tx handling")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
context id and port id should be filled while sending tcb update.
Fixes: 5a4b9fe7fe ("cxgb4/chcr: complete record tx handling")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If TCP congestion caused a very small packets which only has some
part fo the TAG, and that too is not till the end. HW can't handle
such case, so falling back to sw crypto in such cases.
v1->v2:
- Marked chcr_ktls_sw_fallback() static.
Fixes: dc05f3df8f ("chcr: Handle first or middle part of record")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If its a last packet and fin is set. Make sure FIN is informed
to HW before skb gets freed.
Fixes: 429765a149 ("chcr: handle partial end part of a record")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There could be a case where ACK for tls exchanges prior to start
marker is missed out, and by the time tls is offloaded. This pkt
should not be discarded and handled carefully. It could be
plaintext alone or plaintext + finish as well.
Fixes: 5a4b9fe7fe ("cxgb4/chcr: complete record tx handling")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If a record starts in middle, reset TCB UNA so that we could
avoid sending out extra packet which is needed to make it 16
byte aligned to start AES CTR.
Check also considers prev_seq, which should be what is
actually sent, not the skb data length.
Avoid updating partial TAG to HW at any point of time, that's
why we need to check if remaining part is smaller than TAG
size, then reset TX_MAX to be TAG starting sequence number.
Fixes: 5a4b9fe7fe ("cxgb4/chcr: complete record tx handling")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If an skb has only header part which doesn't start from
beginning, is not being handled properly.
Fixes: dc05f3df8f ("chcr: Handle first or middle part of record")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
trimmed length calculation goes wrong if skb has only tag part
to send. It should be zero if there is no data bytes apart from
TAG.
Fixes: dc05f3df8f ("chcr: Handle first or middle part of record")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Creating SKB per tls record and freeing the original one causes
panic. There will be race if connection reset is requested. By
freeing original skb, refcnt will be decremented and that means,
there is no pending record to send, and so tls_dev_del will be
requested in control path while SKB of related connection is in
queue.
Better approach is to use same SKB to send one record (partial
data) at a time. We still have to create a new SKB when partial
last part of a record is requested.
This fix introduces new API cxgb4_write_partial_sgl() to send
partial part of skb. Present cxgb4_write_sgl can only provide
feasibility to start from an offset which limits to header only
and it can write sgls for the whole skb len. But this new API
will help in both. It can start from any offset and can end
writing in middle of the skb.
v4->v5:
- Removed extra changes.
Fixes: 429765a149 ("chcr: handle partial end part of a record")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Checksum update was missing in the WR.
Fixes: 429765a149 ("chcr: handle partial end part of a record")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is a possibility of linear skbs coming in. Correcting
the length extraction logic.
v2->v3:
- Separated un-related changes from this patch.
Fixes: 5a4b9fe7fe ("cxgb4/chcr: complete record tx handling")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If skb has retransmit data starting before start marker, e.g. ccs,
decrypted bit won't be set for that, and if it has some data to
encrypt, then it must be given to crypto ULD. So in place of
decrypted, check if socket is tls offloaded. Also, unless skb has
some data to encrypt, no need to give it for tls offload handling.
v2->v3:
- Removed ifdef.
Fixes: 5a4b9fe7fe ("cxgb4/chcr: complete record tx handling")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the net core, the struct net_device_ops -> ndo_set_rx_mode()
callback is called with the dev->addr_list_lock spinlock held.
However, this driver's ndo_set_rx_mode callback eventually calls
lan743x_dp_write(), which acquires a mutex. Mutex acquisition
may sleep, and this is not allowed when holding a spinlock.
Fix by removing the dp_lock mutex entirely. Its purpose is to
prevent concurrent accesses to the data port. No concurrent
accesses are possible, because the dev->addr_list_lock
spinlock in the core only lets through one thread at a time.
Fixes: 23f0703c12 ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com>
Link: https://lore.kernel.org/r/20201109203828.5115-1-TheSven73@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 6f197fb638 ("lan743x: Added fixed link and RGMII support")
assumes that chips with an internal PHY will never have a devicetree
entry. This is incorrect: even for these chips, a devicetree entry
can be useful e.g. to pass the mac address from bootloader to chip:
&pcie {
status = "okay";
host@0 {
reg = <0 0 0 0 0>;
#address-cells = <3>;
#size-cells = <2>;
lan7430: ethernet@0 {
/* LAN7430 with internal PHY */
compatible = "microchip,lan743x";
status = "okay";
reg = <0 0 0 0 0>;
/* filled in by bootloader */
local-mac-address = [00 00 00 00 00 00];
};
};
};
If a devicetree entry is present, the driver will not attach the chip
to its internal phy, and the chip will be non-operational.
Fix by tweaking the phy connection algorithm:
- first try to connect to a phy specified in the devicetree
(could be 'real' phy, or just a 'fixed-link')
- if that doesn't succeed, try to connect to an internal phy, even
if the chip has a devnode
Tested on a LAN7430 with internal PHY. I cannot test a device using
fixed-link, as I do not have access to one.
Fixes: 6f197fb638 ("lan743x: Added fixed link and RGMII support")
Tested-by: Sven Van Asbroeck <thesven73@gmail.com> # lan7430
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com>
Link: https://lore.kernel.org/r/20201108171224.23829-1-TheSven73@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
'igc_update_stats()' was not updating 'netdev->stats', so the returned
statistics, for example, requested by:
$ ip -s link show dev enp3s0
were not being updated and were always zero.
Fix by returning a set of statistics that are actually being
updated (adapter->stats64).
Fixes: c9a11c23ce ("igc: Add netdev")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The "failure" variable is used without being initialized. It should be
set to false.
Fixes: 8cbf741499 ("i40e, xsk: move buffer allocation out of the Rx processing loop")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix MAC setting flow for the PF driver.
Update the unicast VF's MAC address in VF structure if it is
a new setting in i40e_vc_add_mac_addr_msg.
When unicast MAC address gets deleted, record that and
set the new unicast MAC address that is already waiting in the filter
list. This logic is based on the order of messages arriving to
the PF driver.
Without this change the MAC address setting was interpreted
incorrectly in the following use cases:
1) Print incorrect VF MAC or zero MAC
ip link show dev $pf
2) Don't preserve MAC between driver reload
rmmod iavf; modprobe iavf
3) Update VF MAC when macvlan was set
ip link add link $vf address $mac $vf.1 type macvlan
4) Failed to update mac address when VF was trusted
ip link set dev $vf address $mac
This includes all other configurations including above commands.
Fixes: f657a6e131 ("i40e: Fix VF driver MAC address configuration")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
With CONFIG_BRIDGE=m the compilation fails:
ld: drivers/net/ethernet/marvell/prestera/prestera_switchdev.o: in function `prestera_bridge_port_event':
prestera_switchdev.c:(.text+0x2ebd): undefined reference to `br_vlan_enabled'
in case the driver is statically enabled.
Fix it by adding 'BRIDGE || BRIDGE=n' dependency.
Fixes: e1189d9a5f ("net: marvell: prestera: Add Switchdev driver implementation")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Vadym Kochan <vadym.kochan@plvision.eu>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Link: https://lore.kernel.org/r/20201106161128.24069-1-vadym.kochan@plvision.eu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl+kXcMACgkQSD+KveBX
+j61Zgf+IBCrevYpytPWmbrLnpWP6sVNkg0Plw8cmhRcLCCeN8mEMPIrhNDysmJu
WOen+yVz7K65WEA5LQ1nUM+VY8PdI3sAre81rTrfyEm2Nkd0aO22BoWSESrNZowf
XDNwn4lEJ5MToxvozfV158Gi921EwGtB/JKS6If7Cyjf+Ok8+ie8ayGfvPi7SiNK
+2Bnai7RJSeYYt8xZjvvg17b1+ZbTeoJF/waEXpFsM/BWVKg5ZOawcfRKr4MuvEJ
4WDzCjdaoeDZ8T6cppuWnznpoAeEf6Avq5DG/wMnUQxXRk9X5i043jr1Iydo5Bj9
MvE31Mg9v15CecaKBldVs4cMSv86gw==
=pwvB
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2020-11-03' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2020-11-03
v1->v2:
- Fix fixes line tag in patch #1
- Toss ktls refcount leak fix, Maxim will look further into the root
cause.
- Toss eswitch chain 0 prio patch, until we determine if it is needed
for -rc and net.
* tag 'mlx5-fixes-2020-11-03' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5e: Fix incorrect access of RCU-protected xdp_prog
net/mlx5e: Fix VXLAN synchronization after function reload
net/mlx5: E-switch, Avoid extack error log for disabled vport
net/mlx5: Fix deletion of duplicate rules
net/mlx5e: Use spin_lock_bh for async_icosq_lock
net/mlx5e: Protect encap route dev from concurrent release
net/mlx5e: Fix modify header actions memory leak
====================
Link: https://lore.kernel.org/r/20201105202129.23644-1-saeedm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
RTL8125B has same or similar short packet hw padding bug as RTL8168evl.
The main workaround has been extended accordingly, however we have to
disable also hw checksumming for short packets on affected new chip
versions. Instead of checking for an affected chip version let's
simply disable hw checksumming for short packets in general.
v2:
- remove the version checks and disable short packet hw csum in general
- reflect this in commit title and message
Fixes: 0439297be9 ("r8169: add support for RTL8125B")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/7fbb35f0-e244-ef65-aa55-3872d7d38698@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The caller of rtl8169_tso_csum_v2() frees the skb if false is returned.
eth_skb_pad() internally frees the skb on error what would result in a
double free. Therefore use __skb_put_padto() directly and instruct it
to not free the skb on error.
Fixes: b423e9ae49 ("r8169: fix offloaded tx checksum for small packets.")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/f7e68191-acff-9ded-4263-c016428a8762@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
and netfilter subtrees.
Current release - bugs in new features:
- can: isotp: isotp_rcv_cf(): enable RX timeout handling in
listen-only mode
Previous release - regressions:
- mac80211:
- don't require VHT elements for HE on 2.4 GHz
- fix regression where EAPOL frames were sent in plaintext
- netfilter:
- ipset: Update byte and packet counters regardless of whether
they match
- ip_tunnel: fix over-mtu packet send by allowing fragmenting even
if inner packet has IP_DF (don't fragment) set in its header
(when TUNNEL_DONT_FRAGMENT flag is not set on the tunnel dev)
- net: fec: fix MDIO probing for some FEC hardware blocks
- ip6_tunnel: set inner ipproto before ip6_tnl_encap to un-break
gso support
- sctp: Fix COMM_LOST/CANT_STR_ASSOC err reporting on big-endian
platforms, sparse-related fix used the wrong integer size
Previous release - always broken:
- netfilter: use actual socket sk rather than skb sk when routing
harder
- r8169: work around short packet hw bug on RTL8125 by padding frames
- net: ethernet: ti: cpsw: disable PTPv1 hw timestamping
advertisement, the hardware does not support it
- chelsio/chtls: fix always leaking ctrl_skb and another leak caused
by a race condition
- fix drivers incorrectly writing into skbs on TX:
- cadence: force nonlinear buffers to be cloned
- gianfar: Account for Tx PTP timestamp in the skb headroom
- gianfar: Replace skb_realloc_headroom with skb_cow_head for PTP
- can: flexcan:
- remove FLEXCAN_QUIRK_DISABLE_MECR quirk for LS1021A
- add ECC initialization for VF610 and LX2160A
- flexcan_remove(): disable wakeup completely
- can: fix packet echo functionality:
- peak_canfd: fix echo management when loopback is on
- make sure skbs are not freed in IRQ context in case they need
to be dropped
- always clone the skbs to make sure they have a reference on
the socket, and prevent it from disappearing
- fix real payload length return value for RTR frames
- can: j1939: return failure on bind if netdev is down, rather than
waiting indefinitely
Misc:
- IPv6: reply ICMP error if the first fragment don't include all
headers to improve compliance with RFC 8200
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=5R2w
-----END PGP SIGNATURE-----
Merge tag 'net-5.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes for 5.10-rc3, including fixes from wireless, can, and
netfilter subtrees.
Current merge window - bugs in new features:
- can: isotp: isotp_rcv_cf(): enable RX timeout handling in
listen-only mode
Previous releases - regressions:
- mac80211:
- don't require VHT elements for HE on 2.4 GHz
- fix regression where EAPOL frames were sent in plaintext
- netfilter:
- ipset: Update byte and packet counters regardless of whether
they match
- ip_tunnel: fix over-mtu packet send by allowing fragmenting even if
inner packet has IP_DF (don't fragment) set in its header (when
TUNNEL_DONT_FRAGMENT flag is not set on the tunnel dev)
- net: fec: fix MDIO probing for some FEC hardware blocks
- ip6_tunnel: set inner ipproto before ip6_tnl_encap to un-break gso
support
- sctp: Fix COMM_LOST/CANT_STR_ASSOC err reporting on big-endian
platforms, sparse-related fix used the wrong integer size
Previous releases - always broken:
- netfilter: use actual socket sk rather than skb sk when routing
harder
- r8169: work around short packet hw bug on RTL8125 by padding frames
- net: ethernet: ti: cpsw: disable PTPv1 hw timestamping
advertisement, the hardware does not support it
- chelsio/chtls: fix always leaking ctrl_skb and another leak caused
by a race condition
- fix drivers incorrectly writing into skbs on TX:
- cadence: force nonlinear buffers to be cloned
- gianfar: Account for Tx PTP timestamp in the skb headroom
- gianfar: Replace skb_realloc_headroom with skb_cow_head for PTP
- can: flexcan:
- remove FLEXCAN_QUIRK_DISABLE_MECR quirk for LS1021A
- add ECC initialization for VF610 and LX2160A
- flexcan_remove(): disable wakeup completely
- can: fix packet echo functionality:
- peak_canfd: fix echo management when loopback is on
- make sure skbs are not freed in IRQ context in case they need to
be dropped
- always clone the skbs to make sure they have a reference on the
socket, and prevent it from disappearing
- fix real payload length return value for RTR frames
- can: j1939: return failure on bind if netdev is down, rather than
waiting indefinitely
Misc:
- IPv6: reply ICMP error if the first fragment don't include all
headers to improve compliance with RFC 8200"
* tag 'net-5.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (66 commits)
ionic: check port ptr before use
r8169: work around short packet hw bug on RTL8125
net: openvswitch: silence suspicious RCU usage warning
chelsio/chtls: fix always leaking ctrl_skb
chelsio/chtls: fix memory leaks caused by a race
can: flexcan: flexcan_remove(): disable wakeup completely
can: flexcan: add ECC initialization for VF610
can: flexcan: add ECC initialization for LX2160A
can: flexcan: remove FLEXCAN_QUIRK_DISABLE_MECR quirk for LS1021A
can: mcp251xfd: remove unneeded break
can: mcp251xfd: mcp251xfd_regmap_nocrc_read(): fix semicolon.cocci warnings
can: mcp251xfd: mcp251xfd_regmap_crc_read(): increase severity of CRC read error messages
can: peak_canfd: pucan_handle_can_rx(): fix echo management when loopback is on
can: peak_usb: peak_usb_get_ts_time(): fix timestamp wrapping
can: peak_usb: add range checking in decode operations
can: xilinx_can: handle failure cases of pm_runtime_get_sync
can: ti_hecc: ti_hecc_probe(): add missed clk_disable_unprepare() in error path
can: isotp: padlen(): make const array static, makes object smaller
can: isotp: isotp_rcv_cf(): enable RX timeout handling in listen-only mode
can: isotp: Explain PDU in CAN_ISOTP help text
...
rq->xdp_prog is RCU-protected and should be accessed only with
rcu_access_pointer for the NULL check in mlx5e_poll_rx_cq.
rq->xdp_prog may change on the fly only from one non-NULL value to
another non-NULL value, so the checks in mlx5e_xdp_handle and
mlx5e_poll_rx_cq will have the same result during one NAPI cycle,
meaning that no additional synchronization is needed.
Fixes: fe45386a20 ("net/mlx5e: Use RCU to protect rq->xdp_prog")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
During driver reload, perform firmware tear-down which results in
firmware losing the configured VXLAN ports. These ports are still
available in the driver's database. Fix this by cleaning up driver's
VXLAN database in the nic unload flow, before firmware tear-down. With
that, minimize mlx5_vxlan_destroy() to remove only what was added in
mlx5_vxlan_create() and warn on leftover UDP ports.
Fixes: 18a2b7f969 ("net/mlx5: convert to new udp_tunnel infrastructure")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When E-switch vport is disabled, querying its hardware address is
unsupported.
Avoid setting extack error log message in such case.
Fixes: f099fde16d ("net/mlx5: E-switch, Support querying port function mac address")
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When a rule is duplicated, the refcount of the rule is increased so only
the second deletion of the rule should cause destruction of the FTE.
Currently, the FTE will be destroyed in the first deletion of rule since
the modify_mask will be 0.
Fix it and call to destroy FTE only if all the rules (FTE's children)
have been removed.
Fixes: 718ce4d601 ("net/mlx5: Consolidate update FTE for all removal changes")
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
async_icosq_lock may be taken from softirq and non-softirq contexts. It
requires protection with spin_lock_bh, otherwise a softirq may be
triggered in the middle of the critical section, and it may deadlock if
it tries to take the same lock. This patch fixes such a scenario by
using spin_lock_bh to disable softirqs on that CPU while inside the
critical section.
Fixes: 8d94b590f1 ("net/mlx5e: Turn XSK ICOSQ into a general asynchronous one")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
In functions mlx5e_route_lookup_ipv{4|6}() route_dev can be arbitrary net
device and not necessary mlx5 eswitch port representor. As such, in order
to ensure that route_dev is not destroyed concurrent the code needs either
explicitly take reference to the device before releasing reference to
rtable instance or ensure that caller holds rtnl lock. First approach is
chosen as a fix since rtnl lock dependency was intentionally removed from
mlx5 TC layer.
To prevent unprotected usage of route_dev in encap code take a reference to
the device before releasing rt. Don't save direct pointer to the device in
mlx5_encap_entry structure and use ifindex instead. Modify users of
route_dev pointer to properly obtain the net device instance from its
ifindex.
Fixes: 61086f3910 ("net/mlx5e: Protect encap hash table with mutex")
Fixes: 6707f74be8 ("net/mlx5e: Update hw flows when encap source mac changed")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Modify header actions are allocated during parse tc actions and only
freed during the flow creation, however, on error flow the allocated
memory is wrongly unfreed.
Fix this by calling dealloc_mod_hdr_actions in __mlx5e_add_fdb_flow
and mlx5e_add_nic_flow error flow.
Fixes: d7e75a325c ("net/mlx5e: Add offloading of E-Switch TC pedit (header re-write) actions")
Fixes: 2f4fe4cab0 ("net/mlx5e: Add offloading of NIC TC pedit (header re-write) actions")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Network problems with RTL8125B have been reported [0] and with help
from Realtek it turned out that this chip version has a hw problem
with short packets (similar to RTL8168evl). Having said that activate
the same workaround as for RTL8168evl.
Realtek suggested to activate the workaround for RTL8125A too, even
though they're not 100% sure yet which RTL8125 versions are affected.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=209839
Fixes: 0439297be9 ("r8169: add support for RTL8125B")
Reported-by: Maxim Plotnikov <wgh@torlan.ru>
Tested-by: Maxim Plotnikov <wgh@torlan.ru>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/8002c31a-60b9-58f1-f0dd-8fd07239917f@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Correct skb refcount in alloc_ctrl_skb(), causing skb memleak
when chtls_send_abort() called with NULL skb.
it was always leaking the skb, correct it by incrementing skb
refs by one.
Fixes: cc35c88ae4 ("crypto : chtls - CPL handler definition")
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Link: https://lore.kernel.org/r/20201102173909.24826-1-vinay.yadav@chelsio.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
race between user context and softirq causing memleak,
consider the call sequence scenario
chtls_setkey() //user context
chtls_peer_close()
chtls_abort_req_rss()
chtls_setkey() //user context
work request skb queued in chtls_setkey() won't be freed
because resources are already cleaned for this connection,
fix it by not queuing work request while socket is closing.
v1->v2:
- fix W=1 warning.
v2->v3:
- separate it out from another memleak fix.
Fixes: cc35c88ae4 ("crypto : chtls - CPL handler definition")
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Link: https://lore.kernel.org/r/20201102173650.24754-1-vinay.yadav@chelsio.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 5a18e1e0c1 introduced the 'failover_pending' state to track
the "failover pending window" - where we wait for the partner to become
ready (after a transport event) before actually attempting to failover.
i.e window is between following two events:
a. we get a transport event due to a FAILOVER
b. later, we get CRQ_INITIALIZED indicating the partner is
ready at which point we schedule a FAILOVER reset.
and ->failover_pending is true during this window.
If during this window, we attempt to open (or close) a device, we pretend
that the operation succeded and let the FAILOVER reset path complete the
operation.
This is fine, except if the transport event ("a" above) occurs during the
open and after open has already checked whether a failover is pending. If
that happens, we fail the open, which can cause the boot scripts to leave
the interface down requiring administrator to manually bring up the device.
This fix "extends" the failover pending window till we are _actually_
ready to perform the failover reset (i.e until after we get the RTNL
lock). Since open() holds the RTNL lock, we can be sure that we either
finish the open or if the open() fails due to the failover pending window,
we can again pretend that open is done and let the failover complete it.
We could try and block the open until failover is completed but a) that
could still timeout the application and b) Existing code "pretends" that
failover occurred "just after" open succeeded, so marks the open successful
and lets the failover complete the open. So, mark the open successful even
if the transport event occurs before we actually start the open.
Fixes: 5a18e1e0c1 ("ibmvnic: Fix failover case for non-redundant configuration")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Acked-by: Dany Madden <drt@linux.ibm.com>
Link: https://lore.kernel.org/r/20201030170711.1562994-1-sukadev@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The TI CPTS does not natively support PTPv1, only PTPv2. But, as it
happens, the CPTS can provide HW timestamp for PTPv1 Sync messages, because
CPTS HW parser looks for PTP messageType id in PTP message octet 0 which
value is 0 for PTPv1. As result, CPTS HW can detect Sync messages for PTPv1
and PTPv2 (Sync messageType = 0 for both), but it fails for any other PTPv1
messages (Delay_req/resp) and will return PTP messageType id 0 for them.
The commit e9523a5a32 ("net: ethernet: ti: cpsw: enable
HWTSTAMP_FILTER_PTP_V1_L4_EVENT filter") added PTPv1 hw timestamping
advertisement by mistake, only to make Linux Kernel "timestamping" utility
work, and this causes issues with only PTPv1 compatible HW/SW - Sync HW
timestamped, but Delay_req/resp are not.
Hence, fix it disabling PTPv1 hw timestamping advertisement, so only PTPv1
compatible HW/SW can properly roll back to SW timestamping.
Fixes: e9523a5a32 ("net: ethernet: ti: cpsw: enable HWTSTAMP_FILTER_PTP_V1_L4_EVENT filter")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20201029190910.30789-1-grygorii.strashko@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The headroom reserved for received frames needs to be aligned to an
RX specific value. There is currently a discrepancy between the values
used in the Ethernet driver and the values passed to the FMan.
Coincidentally, the resulting aligned values are identical.
Fixes: 3c68b8fffb ("dpaa_eth: FMan erratum A050385 workaround")
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Impose a larger RX private data area only when the A050385 erratum is
present on the hardware. A smaller buffer size is sufficient in all
other scenarios. This enables a wider range of linear Jumbo frame
sizes in non-erratum scenarios, instead of turning to multi
buffer Scatter/Gather frames. The maximum linear frame size is
increased by 128 bytes for non-erratum arm64 platforms.
Cleanup the hardware annotations header defines in the process.
Fixes: 3c68b8fffb ("dpaa_eth: FMan erratum A050385 workaround")
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In my test setup, I had a SAMA5D27 device configured with ip forwarding, and
second device with usb ethernet (r8152) sending ICMP packets. If the packet
was larger than about 220 bytes, the SAMA5 device would "oops" with the
following trace:
kernel BUG at net/core/skbuff.c:1863!
Internal error: Oops - BUG: 0 [#1] ARM
Modules linked in: xt_MASQUERADE ppp_async ppp_generic slhc iptable_nat xt_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 can_raw can bridge stp llc ipt_REJECT nf_reject_ipv4 sd_mod cdc_ether usbnet usb_storage r8152 scsi_mod mii o
ption usb_wwan usbserial micrel macb at91_sama5d2_adc phylink gpio_sama5d2_piobu m_can_platform m_can industrialio_triggered_buffer kfifo_buf of_mdio can_dev fixed_phy sdhci_of_at91 sdhci_pltfm libphy sdhci mmc_core ohci_at91 ehci_atmel o
hci_hcd iio_rescale industrialio sch_fq_codel spidev prox2_hal(O)
CPU: 0 PID: 0 Comm: swapper Tainted: G O 5.9.1-prox2+ #1
Hardware name: Atmel SAMA5
PC is at skb_put+0x3c/0x50
LR is at macb_start_xmit+0x134/0xad0 [macb]
pc : [<c05258cc>] lr : [<bf0ea5b8>] psr: 20070113
sp : c0d01a60 ip : c07232c0 fp : c4250000
r10: c0d03cc8 r9 : 00000000 r8 : c0d038c0
r7 : 00000000 r6 : 00000008 r5 : c59b66c0 r4 : 0000002a
r3 : 8f659eff r2 : c59e9eea r1 : 00000001 r0 : c59b66c0
Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 10c53c7d Table: 2640c059 DAC: 00000051
Process swapper (pid: 0, stack limit = 0x75002d81)
<snipped stack>
[<c05258cc>] (skb_put) from [<bf0ea5b8>] (macb_start_xmit+0x134/0xad0 [macb])
[<bf0ea5b8>] (macb_start_xmit [macb]) from [<c053e504>] (dev_hard_start_xmit+0x90/0x11c)
[<c053e504>] (dev_hard_start_xmit) from [<c0571180>] (sch_direct_xmit+0x124/0x260)
[<c0571180>] (sch_direct_xmit) from [<c053eae4>] (__dev_queue_xmit+0x4b0/0x6d0)
[<c053eae4>] (__dev_queue_xmit) from [<c05a5650>] (ip_finish_output2+0x350/0x580)
[<c05a5650>] (ip_finish_output2) from [<c05a7e24>] (ip_output+0xb4/0x13c)
[<c05a7e24>] (ip_output) from [<c05a39d0>] (ip_forward+0x474/0x500)
[<c05a39d0>] (ip_forward) from [<c05a13d8>] (ip_sublist_rcv_finish+0x3c/0x50)
[<c05a13d8>] (ip_sublist_rcv_finish) from [<c05a19b8>] (ip_sublist_rcv+0x11c/0x188)
[<c05a19b8>] (ip_sublist_rcv) from [<c05a2494>] (ip_list_rcv+0xf8/0x124)
[<c05a2494>] (ip_list_rcv) from [<c05403c4>] (__netif_receive_skb_list_core+0x1a0/0x20c)
[<c05403c4>] (__netif_receive_skb_list_core) from [<c05405c4>] (netif_receive_skb_list_internal+0x194/0x230)
[<c05405c4>] (netif_receive_skb_list_internal) from [<c0540684>] (gro_normal_list.part.0+0x14/0x28)
[<c0540684>] (gro_normal_list.part.0) from [<c0541280>] (napi_complete_done+0x16c/0x210)
[<c0541280>] (napi_complete_done) from [<bf14c1c0>] (r8152_poll+0x684/0x708 [r8152])
[<bf14c1c0>] (r8152_poll [r8152]) from [<c0541424>] (net_rx_action+0x100/0x328)
[<c0541424>] (net_rx_action) from [<c01012ec>] (__do_softirq+0xec/0x274)
[<c01012ec>] (__do_softirq) from [<c012d6d4>] (irq_exit+0xcc/0xd0)
[<c012d6d4>] (irq_exit) from [<c0160960>] (__handle_domain_irq+0x58/0xa4)
[<c0160960>] (__handle_domain_irq) from [<c0100b0c>] (__irq_svc+0x6c/0x90)
Exception stack(0xc0d01ef0 to 0xc0d01f38)
1ee0: 00000000 0000003d 0c31f383 c0d0fa00
1f00: c0d2eb80 00000000 c0d2e630 4dad8c49 4da967b0 0000003d 0000003d 00000000
1f20: fffffff5 c0d01f40 c04e0f88 c04e0f8c 30070013 ffffffff
[<c0100b0c>] (__irq_svc) from [<c04e0f8c>] (cpuidle_enter_state+0x7c/0x378)
[<c04e0f8c>] (cpuidle_enter_state) from [<c04e12c4>] (cpuidle_enter+0x28/0x38)
[<c04e12c4>] (cpuidle_enter) from [<c014f710>] (do_idle+0x194/0x214)
[<c014f710>] (do_idle) from [<c014fa50>] (cpu_startup_entry+0xc/0x14)
[<c014fa50>] (cpu_startup_entry) from [<c0a00dc8>] (start_kernel+0x46c/0x4a0)
Code: e580c054 8a000002 e1a00002 e8bd8070 (e7f001f2)
---[ end trace 146c8a334115490c ]---
The solution was to force nonlinear buffers to be cloned. This was previously
reported by Klaus Doth (https://www.spinics.net/lists/netdev/msg556937.html)
but never formally submitted as a patch.
This is the third revision, hopefully the formatting is correct this time!
Suggested-by: Klaus Doth <krnl@doth.eu>
Fixes: 653e92a917 ("net: macb: add support for padding and fcs computation")
Signed-off-by: Mark Deneen <mdeneen@saucontech.com>
Link: https://lore.kernel.org/r/20201030155814.622831-1-mdeneen@saucontech.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Hi Linus,
Please, pull the following patches that replace zero-length arrays with
flexible-array members.
Thanks
--
Gustavo
-----BEGIN PGP SIGNATURE-----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=vyu3
-----END PGP SIGNATURE-----
Merge tag 'flexible-array-conversions-5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux
Pull more flexible-array member conversions from Gustavo A. R. Silva:
"Replace zero-length arrays with flexible-array members"
* tag 'flexible-array-conversions-5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
printk: ringbuffer: Replace zero-length array with flexible-array member
net/smc: Replace zero-length array with flexible-array member
net/mlx5: Replace zero-length array with flexible-array member
mei: hw: Replace zero-length array with flexible-array member
gve: Replace zero-length array with flexible-array member
Bluetooth: btintel: Replace zero-length array with flexible-array member
scsi: target: tcmu: Replace zero-length array with flexible-array member
ima: Replace zero-length array with flexible-array member
enetc: Replace zero-length array with flexible-array member
fs: Replace zero-length array with flexible-array member
Bluetooth: Replace zero-length array with flexible-array member
params: Replace zero-length array with flexible-array member
tracepoint: Replace zero-length array with flexible-array member
platform/chrome: cros_ec_proto: Replace zero-length array with flexible-array member
platform/chrome: cros_ec_commands: Replace zero-length array with flexible-array member
mailbox: zynqmp-ipi-message: Replace zero-length array with flexible-array member
dmaengine: ti-cppi5: Replace zero-length array with flexible-array member
There is a regular need in the kernel to provide a way to declare having a
dynamically sized set of trailing elements in a structure. Kernel code
should always use “flexible array members”[1] for these cases. The
older style of one-element or zero-length arrays should no longer be
used[2].
Refactor the code according to the use of a flexible-array member in
struct gve_stats_report, instead of a zero-length array, and use the
struct_size() helper to calculate the size for the resource allocation.
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.9/process/deprecated.html#zero-length-and-one-element-arrays
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
The commit "stmmac: intel: Adding ref clock 1us tic for LPI cntr"
introduced a regression which leads to the kernel panic duing loading
of the dwmac_intel module.
Move the code block after pci resources is obtained.
Fixes: b4c5f83ae3 ("stmmac: intel: Adding ref clock 1us tic for LPI cntr")
Cc: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@intel.com>
Link: https://lore.kernel.org/r/20201029093228.1741-1-vee.khee.wong@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When PTP timestamping is enabled on Tx, the controller
inserts the Tx timestamp at the beginning of the frame
buffer, between SFD and the L2 frame header. This means
that the skb provided by the stack is required to have
enough headroom otherwise a new skb needs to be created
by the driver to accommodate the timestamp inserted by h/w.
Up until now the driver was relying on the second option,
using skb_realloc_headroom() to create a new skb to accommodate
PTP frames. Turns out that this method is not reliable, as
reallocation of skbs for PTP frames along with the required
overhead (skb_set_owner_w, consume_skb) is causing random
crashes in subsequent skb_*() calls, when multiple concurrent
TCP streams are run at the same time on the same device
(as seen in James' report).
Note that these crashes don't occur with a single TCP stream,
nor with multiple concurrent UDP streams, but only when multiple
TCP streams are run concurrently with the PTP packet flow
(doing skb reallocation).
This patch enforces the first method, by requesting enough
headroom from the stack to accommodate PTP frames, and so avoiding
skb_realloc_headroom() & co, and the crashes no longer occur.
There's no reason not to set needed_headroom to a large enough
value to accommodate PTP frames, so in this regard this patch
is a fix.
Reported-by: James Jurack <james.jurack@ametek.com>
Fixes: bee9e58c9e ("gianfar:don't add FCB length to hard_header_len")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20201020173605.1173-1-claudiu.manoil@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When PTP timestamping is enabled on Tx, the controller
inserts the Tx timestamp at the beginning of the frame
buffer, between SFD and the L2 frame header. This means
that the skb provided by the stack is required to have
enough headroom otherwise a new skb needs to be created
by the driver to accommodate the timestamp inserted by h/w.
Up until now the driver was relying on skb_realloc_headroom()
to create new skbs to accommodate PTP frames. Turns out that
this method is not reliable in this context at least, as
skb_realloc_headroom() for PTP frames can cause random crashes,
mostly in subsequent skb_*() calls, when multiple concurrent
TCP streams are run at the same time with the PTP flow
on the same device (as seen in James' report). I also noticed
that when the system is loaded by sending multiple TCP streams,
the driver receives cloned skbs in large numbers.
skb_cow_head() instead proves to be stable in this scenario,
and not only handles cloned skbs too but it's also more efficient
and widely used in other drivers.
The commit introducing skb_realloc_headroom in the driver
goes back to 2009, commit 93c1285c5d
("gianfar: reallocate skb when headroom is not enough for fcb").
For practical purposes I'm referencing a newer commit (from 2012)
that brings the code to its current structure (and fixes the PTP
case).
Fixes: 9c4886e5e6 ("gianfar: Fix invalid TX frames returned on error queue when time stamping")
Reported-by: James Jurack <james.jurack@ametek.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20201029081057.8506-1-claudiu.manoil@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some (apparently older) versions of the FEC hardware block do not like
the MMFR register being cleared to avoid generation of MII events at
initialization time. The action of clearing this register results in no
future MII events being generated at all on the problem block. This means
the probing of the MDIO bus will find no PHYs.
Create a quirk that can be checked at the FECs MII init time so that
the right thing is done. The quirk is set as appropriate for the FEC
hardware blocks that are known to need this.
Fixes: f166f890c8 ("net: ethernet: fec: Replace interrupt driven MDIO with polled IO")
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Acked-by: Fugang Duan <fugand.duan@nxp.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Link: https://lore.kernel.org/r/20201028052232.1315167-1-gerg@linux-m68k.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Current release regressions:
- r8169: fix forced threading conflicting with other shared
interrupts; we tried to fix the use of raise_softirq_irqoff
from an IRQ handler on RT by forcing hard irqs, but this
driver shares legacy PCI IRQs so drop the _irqoff() instead
- tipc: fix memory leak caused by a recent syzbot report fix
to tipc_buf_append()
Current release - bugs in new features:
- devlink: Unlock on error in dumpit() and fix some error codes
- net/smc: fix null pointer dereference in smc_listen_decline()
Previous release - regressions:
- tcp: Prevent low rmem stalls with SO_RCVLOWAT.
- net: protect tcf_block_unbind with block lock
- ibmveth: Fix use of ibmveth in a bridge; the self-imposed filtering
to only send legal frames to the hypervisor was too strict
- net: hns3: Clear the CMDQ registers before unmapping BAR region;
incorrect cleanup order was leading to a crash
- bnxt_en - handful of fixes to fixes:
- Send HWRM_FUNC_RESET fw command unconditionally, even
if there are PCIe errors being reported
- Check abort error state in bnxt_open_nic().
- Invoke cancel_delayed_work_sync() for PFs also.
- Fix regression in workqueue cleanup logic in bnxt_remove_one().
- mlxsw: Only advertise link modes supported by both driver
and device, after removal of 56G support from the driver
56G was not cleared from advertised modes
- net/smc: fix suppressed return code
Previous release - always broken:
- netem: fix zero division in tabledist, caused by integer overflow
- bnxt_en: Re-write PCI BARs after PCI fatal error.
- cxgb4: set up filter action after rewrites
- net: ipa: command payloads already mapped
Misc:
- s390/ism: fix incorrect system EID, it's okay to change since
it was added in current release
- vsock: use ns_capable_noaudit() on socket create to suppress
false positive audit messages
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=reLi
-----END PGP SIGNATURE-----
Merge tag 'net-5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Current release regressions:
- r8169: fix forced threading conflicting with other shared
interrupts; we tried to fix the use of raise_softirq_irqoff from an
IRQ handler on RT by forcing hard irqs, but this driver shares
legacy PCI IRQs so drop the _irqoff() instead
- tipc: fix memory leak caused by a recent syzbot report fix to
tipc_buf_append()
Current release - bugs in new features:
- devlink: Unlock on error in dumpit() and fix some error codes
- net/smc: fix null pointer dereference in smc_listen_decline()
Previous release - regressions:
- tcp: Prevent low rmem stalls with SO_RCVLOWAT.
- net: protect tcf_block_unbind with block lock
- ibmveth: Fix use of ibmveth in a bridge; the self-imposed filtering
to only send legal frames to the hypervisor was too strict
- net: hns3: Clear the CMDQ registers before unmapping BAR region;
incorrect cleanup order was leading to a crash
- bnxt_en - handful of fixes to fixes:
- Send HWRM_FUNC_RESET fw command unconditionally, even if there
are PCIe errors being reported
- Check abort error state in bnxt_open_nic().
- Invoke cancel_delayed_work_sync() for PFs also.
- Fix regression in workqueue cleanup logic in bnxt_remove_one().
- mlxsw: Only advertise link modes supported by both driver and
device, after removal of 56G support from the driver 56G was not
cleared from advertised modes
- net/smc: fix suppressed return code
Previous release - always broken:
- netem: fix zero division in tabledist, caused by integer overflow
- bnxt_en: Re-write PCI BARs after PCI fatal error.
- cxgb4: set up filter action after rewrites
- net: ipa: command payloads already mapped
Misc:
- s390/ism: fix incorrect system EID, it's okay to change since it
was added in current release
- vsock: use ns_capable_noaudit() on socket create to suppress false
positive audit messages"
* tag 'net-5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (36 commits)
r8169: fix issue with forced threading in combination with shared interrupts
netem: fix zero division in tabledist
ibmvnic: fix ibmvnic_set_mac
mptcp: add missing memory scheduling in the rx path
tipc: fix memory leak caused by tipc_buf_append()
gtp: fix an use-before-init in gtp_newlink()
net: protect tcf_block_unbind with block lock
ibmveth: Fix use of ibmveth in a bridge.
net/sched: act_mpls: Add softdep on mpls_gso.ko
ravb: Fix bit fields checking in ravb_hwtstamp_get()
devlink: Unlock on error in dumpit()
devlink: Fix some error codes
chelsio/chtls: fix memory leaks in CPL handlers
chelsio/chtls: fix deadlock issue
net: hns3: Clear the CMDQ registers before unmapping BAR region
bnxt_en: Send HWRM_FUNC_RESET fw command unconditionally.
bnxt_en: Check abort error state in bnxt_open_nic().
bnxt_en: Re-write PCI BARs after PCI fatal error.
bnxt_en: Invoke cancel_delayed_work_sync() for PFs also.
bnxt_en: Fix regression in workqueue cleanup logic in bnxt_remove_one().
...
As reported by Serge flag IRQF_NO_THREAD causes an error if the
interrupt is actually shared and the other driver(s) don't have this
flag set. This situation can occur if a PCI(e) legacy interrupt is
used in combination with forced threading.
There's no good way to deal with this properly, therefore we have to
remove flag IRQF_NO_THREAD. For fixing the original forced threading
issue switch to napi_schedule().
Fixes: 424a646e07 ("r8169: fix operation under forced interrupt threading")
Link: https://www.spinics.net/lists/netdev/msg694960.html
Reported-by: Serge Belyshev <belyshev@depni.sinp.msu.ru>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Serge Belyshev <belyshev@depni.sinp.msu.ru>
Link: https://lore.kernel.org/r/b5b53bfe-35ac-3768-85bf-74d1290cf394@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski brought up a concern in ibmvnic_set_mac().
ibmvnic_set_mac() does this:
ether_addr_copy(adapter->mac_addr, addr->sa_data);
if (adapter->state != VNIC_PROBED)
rc = __ibmvnic_set_mac(netdev, addr->sa_data);
So if state == VNIC_PROBED, the user can assign an invalid address to
adapter->mac_addr, and ibmvnic_set_mac() will still return 0.
The fix is to validate ethernet address at the beginning of
ibmvnic_set_mac(), and move the ether_addr_copy to
the case of "adapter->state != VNIC_PROBED".
Fixes: c26eba03e4 ("ibmvnic: Update reset infrastructure to support tunable parameters")
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Link: https://lore.kernel.org/r/20201027220456.71450-1-ljp@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The check for src mac address in ibmveth_is_packet_unsupported is wrong.
Commit 6f2275433a wanted to shut down messages for loopback packets,
but now suppresses bridged frames, which are accepted by the hypervisor
otherwise bridging won't work at all.
Fixes: 6f2275433a ("ibmveth: Detect unsupported packets before sending to the hypervisor")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Link: https://lore.kernel.org/r/20201026104221.26570-1-msuchanek@suse.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the function ravb_hwtstamp_get() in ravb_main.c with the existing
values for RAVB_RXTSTAMP_TYPE_V2_L2_EVENT (0x2) and RAVB_RXTSTAMP_TYPE_ALL
(0x6)
if (priv->tstamp_rx_ctrl & RAVB_RXTSTAMP_TYPE_V2_L2_EVENT)
config.rx_filter = HWTSTAMP_FILTER_PTP_V2_L2_EVENT;
else if (priv->tstamp_rx_ctrl & RAVB_RXTSTAMP_TYPE_ALL)
config.rx_filter = HWTSTAMP_FILTER_ALL;
if the test on RAVB_RXTSTAMP_TYPE_ALL should be true,
it will never be reached.
This issue can be verified with 'hwtstamp_config' testing program
(tools/testing/selftests/net/hwtstamp_config.c). Setting filter type
to ALL and subsequent retrieving it gives incorrect value:
$ hwtstamp_config eth0 OFF ALL
flags = 0
tx_type = OFF
rx_filter = ALL
$ hwtstamp_config eth0
flags = 0
tx_type = OFF
rx_filter = PTP_V2_L2_EVENT
Correct this by converting if-else's to switch.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Reported-by: Julia Lawall <julia.lawall@inria.fr>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Link: https://lore.kernel.org/r/20201026102130.29368-1-andrew_gabbasov@mentor.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
CPL handler functions chtls_pass_open_rpl() and
chtls_close_listsrv_rpl() should return CPL_RET_BUF_DONE
so that caller function will do skb free to avoid leak.
Fixes: cc35c88ae4 ("crypto : chtls - CPL handler definition")
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Link: https://lore.kernel.org/r/20201025194228.31271-1-vinay.yadav@chelsio.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In chtls_pass_establish() we hold child socket lock using bh_lock_sock
and we are again trying bh_lock_sock in add_to_reap_list, causing deadlock.
Remove bh_lock_sock in add_to_reap_list() as lock is already held.
Fixes: cc35c88ae4 ("crypto : chtls - CPL handler definition")
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Link: https://lore.kernel.org/r/20201025193538.31112-1-vinay.yadav@chelsio.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the AER or firmware reset flow, if we are in fatal error state or
if pci_channel_offline() is true, we don't send any commands to the
firmware because the commands will likely not reach the firmware and
most commands don't matter much because the firmware is likely to be
reset imminently.
However, the HWRM_FUNC_RESET command is different and we should always
attempt to send it. In the AER flow for example, the .slot_reset()
call will trigger this fw command and we need to try to send it to
effect the proper reset.
Fixes: b340dc680e ("bnxt_en: Avoid sending firmware messages when AER error is detected.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a PCIe fatal error occurs, the internal latched BAR addresses
in the chip get reset even though the BAR register values in config
space are retained.
pci_restore_state() will not rewrite the BAR addresses if the
BAR address values are valid, causing the chip's internal BAR addresses
to stay invalid. So we need to zero the BAR registers during PCIe fatal
error to force pci_restore_state() to restore the BAR addresses. These
write cycles to the BAR registers will cause the proper BAR addresses to
latch internally.
Fixes: 6316ea6db9 ("bnxt_en: Enable AER support.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As part of the commit b148bb238c
("bnxt_en: Fix possible crash in bnxt_fw_reset_task()."),
cancel_delayed_work_sync() is called only for VFs to fix a possible
crash by cancelling any pending delayed work items. It was assumed
by mistake that the flush_workqueue() call on the PF would flush
delayed work items as well.
As flush_workqueue() does not cancel the delayed workqueue, extend
the fix for PFs. This fix will avoid the system crash, if there are
any pending delayed work items in fw_reset_task() during driver's
.remove() call.
Unify the workqueue cleanup logic for both PF and VF by calling
cancel_work_sync() and cancel_delayed_work_sync() directly in
bnxt_remove_one().
Fixes: b148bb238c ("bnxt_en: Fix possible crash in bnxt_fw_reset_task().")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A recent patch has moved the workqueue cleanup logic before
calling unregister_netdev() in bnxt_remove_one(). This caused a
regression because the workqueue can be restarted if the device is
still open. Workqueue cleanup must be done after unregister_netdev().
The workqueue will not restart itself after the device is closed.
Call bnxt_cancel_sp_work() after unregister_netdev() and
call bnxt_dl_fw_reporters_destroy() after that. This fixes the
regession and the original NULL ptr dereference issue.
Fixes: b16939b59c ("bnxt_en: Fix NULL ptr dereference crash in bnxt_fw_reset_task()")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Each EMAD transaction stores the skb used to issue the EMAD request
('trans->tx_skb') so that the request could be retried in case of a
timeout. The skb can be freed when a corresponding response is received
or as part of the retry logic (e.g., failed retransmit, exceeded maximum
number of retries).
The two tasks (i.e., response processing and retransmits) are
synchronized by the atomic 'trans->active' field which ensures that
responses to inactive transactions are ignored.
In case of a failed retransmit the transaction is finished and all of
its resources are freed. However, the current code does not mark it as
inactive. Syzkaller was able to hit a race condition in which a
concurrent response is processed while the transaction's resources are
being freed, resulting in a use-after-free [1].
Fix the issue by making sure to mark the transaction as inactive after a
failed retransmit and free its resources only if a concurrent task did
not already do that.
[1]
BUG: KASAN: use-after-free in consume_skb+0x30/0x370
net/core/skbuff.c:833
Read of size 4 at addr ffff88804f570494 by task syz-executor.0/1004
CPU: 0 PID: 1004 Comm: syz-executor.0 Not tainted 5.8.0-rc7+ #68
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xf6/0x16e lib/dump_stack.c:118
print_address_description.constprop.0+0x1c/0x250
mm/kasan/report.c:383
__kasan_report mm/kasan/report.c:513 [inline]
kasan_report.cold+0x1f/0x37 mm/kasan/report.c:530
check_memory_region_inline mm/kasan/generic.c:186 [inline]
check_memory_region+0x14e/0x1b0 mm/kasan/generic.c:192
instrument_atomic_read include/linux/instrumented.h:56 [inline]
atomic_read include/asm-generic/atomic-instrumented.h:27 [inline]
refcount_read include/linux/refcount.h:147 [inline]
skb_unref include/linux/skbuff.h:1044 [inline]
consume_skb+0x30/0x370 net/core/skbuff.c:833
mlxsw_emad_trans_finish+0x64/0x1c0 drivers/net/ethernet/mellanox/mlxsw/core.c:592
mlxsw_emad_process_response drivers/net/ethernet/mellanox/mlxsw/core.c:651 [inline]
mlxsw_emad_rx_listener_func+0x5c9/0xac0 drivers/net/ethernet/mellanox/mlxsw/core.c:672
mlxsw_core_skb_receive+0x4df/0x770 drivers/net/ethernet/mellanox/mlxsw/core.c:2063
mlxsw_pci_cqe_rdq_handle drivers/net/ethernet/mellanox/mlxsw/pci.c:595 [inline]
mlxsw_pci_cq_tasklet+0x12a6/0x2520 drivers/net/ethernet/mellanox/mlxsw/pci.c:651
tasklet_action_common.isra.0+0x13f/0x3e0 kernel/softirq.c:550
__do_softirq+0x223/0x964 kernel/softirq.c:292
asm_call_on_stack+0x12/0x20 arch/x86/entry/entry_64.S:711
Allocated by task 1006:
save_stack+0x1b/0x40 mm/kasan/common.c:48
set_track mm/kasan/common.c:56 [inline]
__kasan_kmalloc mm/kasan/common.c:494 [inline]
__kasan_kmalloc.constprop.0+0xc2/0xd0 mm/kasan/common.c:467
slab_post_alloc_hook mm/slab.h:586 [inline]
slab_alloc_node mm/slub.c:2824 [inline]
slab_alloc mm/slub.c:2832 [inline]
kmem_cache_alloc+0xcd/0x2e0 mm/slub.c:2837
__build_skb+0x21/0x60 net/core/skbuff.c:311
__netdev_alloc_skb+0x1e2/0x360 net/core/skbuff.c:464
netdev_alloc_skb include/linux/skbuff.h:2810 [inline]
mlxsw_emad_alloc drivers/net/ethernet/mellanox/mlxsw/core.c:756 [inline]
mlxsw_emad_reg_access drivers/net/ethernet/mellanox/mlxsw/core.c:787 [inline]
mlxsw_core_reg_access_emad+0x1ab/0x1420 drivers/net/ethernet/mellanox/mlxsw/core.c:1817
mlxsw_reg_trans_query+0x39/0x50 drivers/net/ethernet/mellanox/mlxsw/core.c:1831
mlxsw_sp_sb_pm_occ_clear drivers/net/ethernet/mellanox/mlxsw/spectrum_buffers.c:260 [inline]
mlxsw_sp_sb_occ_max_clear+0xbff/0x10a0 drivers/net/ethernet/mellanox/mlxsw/spectrum_buffers.c:1365
mlxsw_devlink_sb_occ_max_clear+0x76/0xb0 drivers/net/ethernet/mellanox/mlxsw/core.c:1037
devlink_nl_cmd_sb_occ_max_clear_doit+0x1ec/0x280 net/core/devlink.c:1765
genl_family_rcv_msg_doit net/netlink/genetlink.c:669 [inline]
genl_family_rcv_msg net/netlink/genetlink.c:714 [inline]
genl_rcv_msg+0x617/0x980 net/netlink/genetlink.c:731
netlink_rcv_skb+0x152/0x440 net/netlink/af_netlink.c:2470
genl_rcv+0x24/0x40 net/netlink/genetlink.c:742
netlink_unicast_kernel net/netlink/af_netlink.c:1304 [inline]
netlink_unicast+0x53a/0x750 net/netlink/af_netlink.c:1330
netlink_sendmsg+0x850/0xd90 net/netlink/af_netlink.c:1919
sock_sendmsg_nosec net/socket.c:651 [inline]
sock_sendmsg+0x150/0x190 net/socket.c:671
____sys_sendmsg+0x6d8/0x840 net/socket.c:2359
___sys_sendmsg+0xff/0x170 net/socket.c:2413
__sys_sendmsg+0xe5/0x1b0 net/socket.c:2446
do_syscall_64+0x56/0xa0 arch/x86/entry/common.c:384
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Freed by task 73:
save_stack+0x1b/0x40 mm/kasan/common.c:48
set_track mm/kasan/common.c:56 [inline]
kasan_set_free_info mm/kasan/common.c:316 [inline]
__kasan_slab_free+0x12c/0x170 mm/kasan/common.c:455
slab_free_hook mm/slub.c:1474 [inline]
slab_free_freelist_hook mm/slub.c:1507 [inline]
slab_free mm/slub.c:3072 [inline]
kmem_cache_free+0xbe/0x380 mm/slub.c:3088
kfree_skbmem net/core/skbuff.c:622 [inline]
kfree_skbmem+0xef/0x1b0 net/core/skbuff.c:616
__kfree_skb net/core/skbuff.c:679 [inline]
consume_skb net/core/skbuff.c:837 [inline]
consume_skb+0xe1/0x370 net/core/skbuff.c:831
mlxsw_emad_trans_finish+0x64/0x1c0 drivers/net/ethernet/mellanox/mlxsw/core.c:592
mlxsw_emad_transmit_retry.isra.0+0x9d/0xc0 drivers/net/ethernet/mellanox/mlxsw/core.c:613
mlxsw_emad_trans_timeout_work+0x43/0x50 drivers/net/ethernet/mellanox/mlxsw/core.c:625
process_one_work+0xa3e/0x17a0 kernel/workqueue.c:2269
worker_thread+0x9e/0x1050 kernel/workqueue.c:2415
kthread+0x355/0x470 kernel/kthread.c:291
ret_from_fork+0x22/0x30 arch/x86/entry/entry_64.S:293
The buggy address belongs to the object at ffff88804f5703c0
which belongs to the cache skbuff_head_cache of size 224
The buggy address is located 212 bytes inside of
224-byte region [ffff88804f5703c0, ffff88804f5704a0)
The buggy address belongs to the page:
page:ffffea00013d5c00 refcount:1 mapcount:0 mapping:0000000000000000
index:0x0
flags: 0x100000000000200(slab)
raw: 0100000000000200 dead000000000100 dead000000000122 ffff88806c625400
raw: 0000000000000000 00000000000c000c 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff88804f570380: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb
ffff88804f570400: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff88804f570480: fb fb fb fb fc fc fc fc fc fc fc fc fc fc fc fc
^
ffff88804f570500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff88804f570580: 00 00 00 00 00 00 00 00 00 00 00 00 fc fc fc fc
Fixes: caf7297e7a ("mlxsw: core: Introduce support for asynchronous EMAD register access")
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During port creation the driver instructs the device to advertise all
the supported link modes queried from the device.
Since cited commit not all the link modes supported by the device are
supported by the driver. This can result in the device negotiating a
link mode that is not recognized by the driver causing ethtool to show
an unsupported speed:
$ ethtool swp1
...
Speed: Unknown!
This is especially problematic when the netdev is enslaved to a bond, as
the bond driver uses unknown speed as an indication that the link is
down:
[13048.900895] net_ratelimit: 86 callbacks suppressed
[13048.900902] t_bond0: (slave swp52): failed to get link speed/duplex
[13048.912160] t_bond0: (slave swp49): failed to get link speed/duplex
Fix this by making sure that only link modes that are supported by both
the device and the driver are advertised.
Fixes: b97cd89126 ("mlxsw: Remove 56G speed support")
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current code sets up the filter action field before
rewrites are set up. When the action 'switch' is used
with rewrites, this may result in initial few packets
that get switched out don't have rewrites applied
on them.
So, make sure filter action is set up along with rewrites
or only after everything else is set up for rewrites.
Fixes: 12b276fbf6 ("cxgb4: add support to create hash filters")
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Link: https://lore.kernel.org/r/20201023115852.18262-1-rajur@chelsio.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Smatch complains that "ret" might be uninitialized if we don't enter
the loop. We do always enter the loop so it's a false positive, but
it's cleaner to just return a literal zero and that silences the
warning as well.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20201023112212.GA282278@mwanda
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a mlx5 core devlink instance is reloaded in different net namespace,
its associated IB device is deleted and recreated.
Example sequence is:
$ ip netns add foo
$ devlink dev reload pci/0000:00:08.0 netns foo
$ ip netns del foo
mlx5 IB device needs to attach and detach the netdevice to it through the
netdev notifier chain during load and unload sequence. A below call graph
of the unload flow.
cleanup_net()
down_read(&pernet_ops_rwsem); <- first sem acquired
ops_pre_exit_list()
pre_exit()
devlink_pernet_pre_exit()
devlink_reload()
mlx5_devlink_reload_down()
mlx5_unload_one()
[...]
mlx5_ib_remove()
mlx5_ib_unbind_slave_port()
mlx5_remove_netdev_notifier()
unregister_netdevice_notifier()
down_write(&pernet_ops_rwsem);<- recurrsive lock
Hence, when net namespace is deleted, mlx5 reload results in deadlock.
When deadlock occurs, devlink mutex is also held. This not only deadlocks
the mlx5 device under reload, but all the processes which attempt to
access unrelated devlink devices are deadlocked.
Hence, fix this by mlx5 ib driver to register for per net netdev notifier
instead of global one, which operats on the net namespace without holding
the pernet_ops_rwsem.
Fixes: 4383cfcc65 ("net/mlx5: Add devlink reload")
Link: https://lore.kernel.org/r/20201026134359.23150-1-parav@nvidia.com
Signed-off-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Clang warns about the extra parentheses in this comparison:
drivers/net/ethernet/freescale/ucc_geth.c:1361:28:
warning: equality comparison with extraneous parentheses
if ((ugeth->phy_interface == PHY_INTERFACE_MODE_SGMII))
~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~
It seems clear the intent here is to do a comparison not an
assignment, so drop the extra parentheses to avoid any confusion.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201023033236.3296988-1-mpe@ellerman.id.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The sentinel descriptor entry was getting missed in the
traverse of the ring from head to tail, so change to a
loop of 0 to the end.
Fixes: f1d2e894f1 ("ionic: use index not pointer for queue tracking")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kmemleak pointed out to us that ionic_rx_flush() is sending
skbs into napi_gro_XXX with a disabled napi context, and these
end up getting lost and leaked. We can safely remove the flush.
Fixes: 0f3154e6bc ("ionic: Add Tx and Rx handling")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The sparse complaints around the static_asserts were obscuring
more useful complaints. So, don't check the static_asserts,
and fix the remaining sparse complaints.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
chtls_pt_recvmsg() receives a skb with tls header and subsequent
skb with data, need to finalize the data copy whenever next skb
with tls header is available. but here current tls header is
overwritten by next available tls header, ends up corrupting
user buffer data. fixing it by finalizing current record whenever
next skb contains tls header.
v1->v2:
- Improved commit message.
Fixes: 17a7d24aa8 ("crypto: chtls - generic handling of data and hdr")
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Link: https://lore.kernel.org/r/20201022190556.21308-1-vinay.yadav@chelsio.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-tree/merge window issues:
- rtl8150: don't incorrectly assign random MAC addresses; fix late
in the 5.9 cycle started depending on a return code from
a function which changed with the 5.10 PR from the usb subsystem
Current release - regressions:
- Revert "virtio-net: ethtool configurable RXCSUM", it was causing
crashes at probe when control vq was not negotiated/available
Previous releases - regressions:
- ixgbe: fix probing of multi-port 10 Gigabit Intel NICs with an MDIO
bus, only first device would be probed correctly
- nexthop: Fix performance regression in nexthop deletion by
effectively switching from recently added synchronize_rcu()
to synchronize_rcu_expedited()
- netsec: ignore 'phy-mode' device property on ACPI systems;
the property is not populated correctly by the firmware,
but firmware configures the PHY so just keep boot settings
Previous releases - always broken:
- tcp: fix to update snd_wl1 in bulk receiver fast path, addressing
bulk transfers getting "stuck"
- icmp: randomize the global rate limiter to prevent attackers from
getting useful signal
- r8169: fix operation under forced interrupt threading, make the
driver always use hard irqs, even on RT, given the handler is
light and only wants to schedule napi (and do so through
a _irqoff() variant, preferably)
- bpf: Enforce pointer id generation for all may-be-null register
type to avoid pointers erroneously getting marked as null-checked
- tipc: re-configure queue limit for broadcast link
- net/sched: act_tunnel_key: fix OOB write in case of IPv6 ERSPAN
tunnels
- fix various issues in chelsio inline tls driver
Misc:
- bpf: improve just-added bpf_redirect_neigh() helper api to support
supplying nexthop by the caller - in case BPF program has already
done a lookup we can avoid doing another one
- remove unnecessary break statements
- make MCTCP not select IPV6, but rather depend on it
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=ceke
-----END PGP SIGNATURE-----
Merge tag 'net-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Cross-tree/merge window issues:
- rtl8150: don't incorrectly assign random MAC addresses; fix late in
the 5.9 cycle started depending on a return code from a function
which changed with the 5.10 PR from the usb subsystem
Current release regressions:
- Revert "virtio-net: ethtool configurable RXCSUM", it was causing
crashes at probe when control vq was not negotiated/available
Previous release regressions:
- ixgbe: fix probing of multi-port 10 Gigabit Intel NICs with an MDIO
bus, only first device would be probed correctly
- nexthop: Fix performance regression in nexthop deletion by
effectively switching from recently added synchronize_rcu() to
synchronize_rcu_expedited()
- netsec: ignore 'phy-mode' device property on ACPI systems; the
property is not populated correctly by the firmware, but firmware
configures the PHY so just keep boot settings
Previous releases - always broken:
- tcp: fix to update snd_wl1 in bulk receiver fast path, addressing
bulk transfers getting "stuck"
- icmp: randomize the global rate limiter to prevent attackers from
getting useful signal
- r8169: fix operation under forced interrupt threading, make the
driver always use hard irqs, even on RT, given the handler is light
and only wants to schedule napi (and do so through a _irqoff()
variant, preferably)
- bpf: Enforce pointer id generation for all may-be-null register
type to avoid pointers erroneously getting marked as null-checked
- tipc: re-configure queue limit for broadcast link
- net/sched: act_tunnel_key: fix OOB write in case of IPv6 ERSPAN
tunnels
- fix various issues in chelsio inline tls driver
Misc:
- bpf: improve just-added bpf_redirect_neigh() helper api to support
supplying nexthop by the caller - in case BPF program has already
done a lookup we can avoid doing another one
- remove unnecessary break statements
- make MCTCP not select IPV6, but rather depend on it"
* tag 'net-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (62 commits)
tcp: fix to update snd_wl1 in bulk receiver fast path
net: Properly typecast int values to set sk_max_pacing_rate
netfilter: nf_fwd_netdev: clear timestamp in forwarding path
ibmvnic: save changed mac address to adapter->mac_addr
selftests: mptcp: depends on built-in IPv6
Revert "virtio-net: ethtool configurable RXCSUM"
rtnetlink: fix data overflow in rtnl_calcit()
net: ethernet: mtk-star-emac: select REGMAP_MMIO
net: hdlc_raw_eth: Clear the IFF_TX_SKB_SHARING flag after calling ether_setup
net: hdlc: In hdlc_rcv, check to make sure dev is an HDLC device
bpf, libbpf: Guard bpf inline asm from bpf_tail_call_static
bpf, selftests: Extend test_tc_redirect to use modified bpf_redirect_neigh()
bpf: Fix bpf_redirect_neigh helper api to support supplying nexthop
mptcp: depends on IPV6 but not as a module
sfc: move initialisation of efx->filter_sem to efx_init_struct()
mpls: load mpls_gso after mpls_iptunnel
net/sched: act_tunnel_key: fix OOB write in case of IPv6 ERSPAN tunnels
net/sched: act_gate: Unlock ->tcfa_lock in tc_setup_flow_action()
net: dsa: bcm_sf2: make const array static, makes object smaller
mptcp: MPTCP_IPV6 should depend on IPV6 instead of selecting it
...
After mac address change request completes successfully, the new mac
address need to be saved to adapter->mac_addr as well as
netdev->dev_addr. Otherwise, adapter->mac_addr still holds old
data.
Fixes: 62740e9788 ("net/ibmvnic: Update MAC address settings after adapter reset")
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Link: https://lore.kernel.org/r/20201020223919.46106-1-ljp@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver depends on mmio regmap API but doesn't select the appropriate
Kconfig option. This fixes it.
Fixes: 8c7bd5a454 ("net: ethernet: mtk-star-emac: new driver")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20201020073515.22769-1-brgl@bgdev.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
efx_probe_filters() has not been called yet when EF100 calls into
efx_mcdi_filter_table_probe(), for which it wants to take the
filter_sem.
Fixes: a9dc3d5612 ("sfc_ef100: RX filter table management and related gubbins")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Link: https://lore.kernel.org/r/24fad43e-887d-051e-25e3-506f23f63abf@solarflare.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix build errors when TLS=m, TLS_TOE=y, and CRYPTO_DEV_CHELSIO_TLS=y.
Having (tristate) CRYPTO_DEV_CHELSIO_TLS depend on (bool) TLS_TOE
is not strong enough to prevent the bad combination of TLS=m and
CRYPTO_DEV_CHELSIO_TLS=y, so add a dependency on TLS to prevent the
problematic kconfig combination.
Fixes these build errors:
hppa-linux-ld: drivers/net/ethernet/chelsio/inline_crypto/chtls/chtls_main.o: in function `chtls_free_uld':
drivers/net/ethernet/chelsio/inline_crypto/chtls/chtls_main.c:165: undefined reference to `tls_toe_unregister_device'
hppa-linux-ld: drivers/net/ethernet/chelsio/inline_crypto/chtls/chtls_main.o: in function `chtls_register_dev':
drivers/net/ethernet/chelsio/inline_crypto/chtls/chtls_main.c:204: undefined reference to `tls_toe_register_device'
Fixes: 53b4414a70 ("net/tls: allow compiling TLS TOE out")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20201019181059.22634-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When chtls_sock *csk is freed, same memory can be allocated
to different csk in chtls_sock_create().
csk->cdev = NULL; statement might ends up modifying wrong
csk, eventually causing kernel panic.
removing (csk->cdev = NULL) statement as it is not required.
Fixes: 3a0a978389 ("crypto/chtls: Fix chtls crash in connection cleanup")
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the logic to compare net_device returned by ip_dev_find()
with the net_device list in cdev->ports[] array and return
net_device if matched else NULL.
Fixes: 6abde0b241 ("crypto/chtls: IPv6 support for inline TLS")
Signed-off-by: Venkatesh Ellapu <venkatesh.e@chelsio.com>
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Netdev is filled in egress_dev when connection is established,
If connection is closed before establishment, then egress_dev
is NULL, Fix it using ip_dev_find() rather then extracting from
egress_dev.
Fixes: 6abde0b241 ("crypto/chtls: IPv6 support for inline TLS")
Signed-off-by: Venkatesh Ellapu <venkatesh.e@chelsio.com>
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In chtls_sendpage() socket lock is released but not acquired,
fix it by taking lock.
Fixes: 36bedb3f2e ("crypto: chtls - Inline TLS record Tx")
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e rx/tx
delay config"), the Realtek PHY driver will override any TX/RX delay
set by hardware straps if the phy-mode device property does not match.
This is causing problems on SynQuacer based platforms (the only SoC
that incorporates the netsec hardware), since many were built with
this Realtek PHY, and shipped with firmware that defines the phy-mode
as 'rgmii', even though the PHY is configured for TX and RX delay using
pull-ups.
From the driver's perspective, we should not make any assumptions in
the general case that the PHY hardware does not require any initial
configuration. However, the situation is slightly different for ACPI
boot, since it implies rich firmware with AML abstractions to handle
hardware details that are not exposed to the OS. So in the ACPI case,
it is reasonable to assume that the PHY comes up in the right mode,
regardless of whether the mode is set by straps, by boot time firmware
or by AML executed by the ACPI interpreter.
So let's ignore the 'phy-mode' device property when probing the netsec
driver in ACPI mode, and hardcode the mode to PHY_INTERFACE_MODE_NA,
which should work with any PHY provided that it is configured by the
time the driver attaches to it. While at it, document that omitting
the mode is permitted for DT probing as well, by setting the phy-mode
DT property to the empty string.
Fixes: 533dd11a12 ("net: socionext: Add Synquacer NetSec driver")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201018163625.2392-1-ardb@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fixes gcc warning:
passing argument 1 of 'kfree' makes pointer from integer without a cast
Fixes: 3af5f0f5c7 ("net: korina: fix kfree of rx/tx descriptor array")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Valentin Vidic <vvidic@valentin-vidic.from.hr>
Link: https://lore.kernel.org/r/20201018184255.28989-1-vvidic@valentin-vidic.from.hr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For several network drivers it was reported that using
__napi_schedule_irqoff() is unsafe with forced threading. One way to
fix this is switching back to __napi_schedule, but then we lose the
benefit of the irqoff version in general. As stated by Eric it doesn't
make sense to make the minimal hard irq handlers in drivers using NAPI
a thread. Therefore ensure that the hard irq handler is never
thread-ified.
Fixes: 9a899a35b0 ("r8169: switch to napi_schedule_irqoff")
Link: https://lkml.org/lkml/2020/10/18/19
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/4d3ef84a-c812-5072-918a-22a6f6468310@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ian reports that after upgrade from v5.8.14 to v5.9 only one
of his 4 ixgbe netdevs appear in the system.
Quoting the comment on ixgbe_x550em_a_has_mii():
* Returns true if hw points to lowest numbered PCI B:D.F x550_em_a device in
* the SoC. There are up to 4 MACs sharing a single MDIO bus on the x550em_a,
* but we only want to register one MDIO bus.
This matches the symptoms, since the return value from
ixgbe_mii_bus_init() is no longer ignored we need to handle
the higher ports of x550em without an error.
Fixes: 09ef193fef ("net: ethernet: ixgbe: check the return value of ixgbe_mii_bus_init()")
Reported-by: Ian Kumlien <ian.kumlien@gmail.com>
Tested-by: Ian Kumlien <ian.kumlien@gmail.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20201016232006.3352947-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The typical set of driver updates across the subsystem:
- Driver minor changes and bug fixes for mlx5, efa, rxe, vmw_pvrdma, hns,
usnic, qib, qedr, cxgb4, hns, bnxt_re
- Various rtrs fixes and updates
- Bug fix for mlx4 CM emulation for virtualization scenarios where MRA
wasn't working right
- Use tracepoints instead of pr_debug in the CM code
- Scrub the locking in ucma and cma to close more syzkaller bugs
- Use tasklet_setup in the subsystem
- Revert the idea that 'destroy' operations are not allowed to fail at
the driver level. This proved unworkable from a HW perspective.
- Revise how the umem API works so drivers make fewer mistakes using it
- XRC support for qedr
- Convert uverbs objects RWQ and MW to new the allocation scheme
- Large queue entry sizes for hns
- Use hmm_range_fault() for mlx5 On Demand Paging
- uverbs APIs to inspect the GID table instead of sysfs
- Move some of the RDMA code for building large page SGLs into
lib/scatterlist
-----BEGIN PGP SIGNATURE-----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=LKpl
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"A usual cycle for RDMA with a typical mix of driver and core subsystem
updates:
- Driver minor changes and bug fixes for mlx5, efa, rxe, vmw_pvrdma,
hns, usnic, qib, qedr, cxgb4, hns, bnxt_re
- Various rtrs fixes and updates
- Bug fix for mlx4 CM emulation for virtualization scenarios where
MRA wasn't working right
- Use tracepoints instead of pr_debug in the CM code
- Scrub the locking in ucma and cma to close more syzkaller bugs
- Use tasklet_setup in the subsystem
- Revert the idea that 'destroy' operations are not allowed to fail
at the driver level. This proved unworkable from a HW perspective.
- Revise how the umem API works so drivers make fewer mistakes using
it
- XRC support for qedr
- Convert uverbs objects RWQ and MW to new the allocation scheme
- Large queue entry sizes for hns
- Use hmm_range_fault() for mlx5 On Demand Paging
- uverbs APIs to inspect the GID table instead of sysfs
- Move some of the RDMA code for building large page SGLs into
lib/scatterlist"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (191 commits)
RDMA/ucma: Fix use after free in destroy id flow
RDMA/rxe: Handle skb_clone() failure in rxe_recv.c
RDMA/rxe: Move the definitions for rxe_av.network_type to uAPI
RDMA: Explicitly pass in the dma_device to ib_register_device
lib/scatterlist: Do not limit max_segment to PAGE_ALIGNED values
IB/mlx4: Convert rej_tmout radix-tree to XArray
RDMA/rxe: Fix bug rejecting all multicast packets
RDMA/rxe: Fix skb lifetime in rxe_rcv_mcast_pkt()
RDMA/rxe: Remove duplicate entries in struct rxe_mr
IB/hfi,rdmavt,qib,opa_vnic: Update MAINTAINERS
IB/rdmavt: Fix sizeof mismatch
MAINTAINERS: CISCO VIC LOW LATENCY NIC DRIVER
RDMA/bnxt_re: Fix sizeof mismatch for allocation of pbl_tbl.
RDMA/bnxt_re: Use rdma_umem_for_each_dma_block()
RDMA/umem: Move to allocate SG table from pages
lib/scatterlist: Add support in dynamic allocation of SG table from pages
tools/testing/scatterlist: Show errors in human readable form
tools/testing/scatterlist: Rejuvenate bit-rotten test
RDMA/ipoib: Set rtnl_link_ops for ipoib interfaces
RDMA/uverbs: Expose the new GID query API to user space
...
