DSC is not supported on DP MST streams so just don't add this entry for
MST connectors.
This also fixes an OOPS, caused by the encoder->digport cast, which is
not valid for MST encoders.
v2:
- Check encoder, which is unset for an MST connector, before it gets
enabled.
v3:
- Just don't add this debugfs file for MST connectors. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200609184140.4937-1-imre.deak@intel.com
According to BSpec the Data Island Packet should be disabled after
disabling the transcoder, but before the transcoder clock select is set
to none. On an ICL RVP, daisy-chained MST config not following this
leads to a hang with the following MCE when disabling the output:
[ 870.948739] mce: [Hardware Error]: CPU 0: Machine Check Exception: 5 Bank 6: ba00000011000402
[ 871.019212] mce: [Hardware Error]: RIP !INEXACT! 10:<ffffffff81aca652> {poll_idle+0x92/0xb0}
[ 871.019212] mce: [Hardware Error]: TSC 135a261fe61
[ 871.019212] mce: [Hardware Error]: PROCESSOR 0:706e5 TIME 1591739604 SOCKET 0 APIC 0 microcode 20
[ 871.019212] mce: [Hardware Error]: Run the above through 'mcelog --ascii'
[ 871.019212] mce: [Hardware Error]: Machine check: Processor context corrupt
[ 871.019212] Kernel panic - not syncing: Fatal machine check
[ 871.019212] Kernel Offset: disabled
Bspec: 4287
Fixes: fa37a21327 ("drm/i915: Stop sending DP SDPs on ddi disable")
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200609220616.6015-1-imre.deak@intel.com
RKL doesn't have DSI outputs, so we shouldn't try to read out the DSI
transcoder registers.
v2(MattR):
- Just set the 'extra panel mask' to edp | dsi0 | dsi1 and then mask
against the platform's cpu_transcoder_mask to filter out the ones
that don't exist on a given platform. (Ville)
v3(MattR):
- Only include DSI transcoders on gen11+ again. (Ville)
- Use for_each_cpu_transcoder_masked() for loop. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200606025740.3308880-5-matthew.d.roper@intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
HPD pin handling for RKL+TGP is a special case; we effectively select
the HPD pin based on the DDI (A,B,D,E) rather than the PHY (A,B,C,D).
This differs from the regular behavior of RKL+CMP (and also TGL+TGP).
v2:
- Rather than providing a custom hpd_pin mapping table, just assign
encoder->hpd_pin in a custom manner for this setup. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200606025740.3308880-4-matthew.d.roper@intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Rocket Lake uses the same 'abox0' mechanism to handle pixel data
transfers from memory that gen11 platforms used, rather than the
abox1/abox2 interfaces used by TGL/DG1. For the most part this is a
hardware implementation detail that's transparent to driver software,
but we do have to program a couple of tuning registers (MBUS_ABOX_CTL
and BW_BUDDY registers) according to which ABOX instances are used by a
platform. Let's track the platform's ABOX usage in the device info
structure and use that to determine which instances of these registers
to program.
As an exception to this rule is that even though TGL/DG1 use ABOX1+ABOX2
for data transfers, we're still directed to program the ABOX_CTL
register for ABOX0; so we'll handle that as a special case.
v2:
- Store the mask of platform-specific abox registers in the device
info structure.
- Add a TLB_REQ_TIMER() helper macro. (Aditya)
v3:
- Squash ABOX and BW_BUDDY patches together and use a single mask for
both of them, plus a special-case for programming the ABOX0 instance
on all gen12. (Ville)
Bspec: 50096
Bspec: 49218
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Aditya Swarup <aditya.swarup@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200606025740.3308880-2-matthew.d.roper@intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Avoid a NULL dereference for a mismatched encoder type, hit when
probing state for all encoders.
This is a band aid to prevent the OOPS as the right fix is "probably to
swap the psr vs infoframes.enable checks, or outright disappear from
this function" (Ville).
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/1892
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200525124912.16019-1-chris@chris-wilson.co.uk
(cherry picked from commit 22da5d846d)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
This reverts commit 82ea174dc5.
Unfortunately according to our recent findings there is still some
unidentified factor, requiring CDCLK to be set higher - otherwise we
still get underruns on some multipipe configurations, despite CDCLK
being set according to BSpec formula. So getting again back into debug
mode to indentify the cause, meanwhile setting CDCLK=Pixel rate back in
order to remove regression in 10% of the cases due to FIFO underruns.
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Fixes: cd19154608 ("drm/i915: Adjust CDCLK accordingly to our DBuf bw needs")
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200608065552.21728-1-stanislav.lisovskiy@intel.com
- Includes gvt-next-fixes-2020-05-28
- Use after free fix for display global state.
- Whitelisting context-local timestamp on Gen9
and two scheduler fixes with deps (Cc: stable)
- Removal of write flag from sysfs files where
ineffective
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200604150454.GA59322@jlahtine-desk.ger.corp.intel.com
The IO buffer Wake and Fast Wake bit size and value have been changed from
Gen12+. It programs the default value of IO buffer Wake and Fast Wake on
Gen12+. It adds definitions of IO buffer Wake and Fast Wake for pre Gen12
and Gen12+. And it aligns PSR2 definition macros.
v2: Fix macro definitions. (José)
v3: Addressed review comments from José
- Add missing default values of IO_BUFFER_WAKE and FAST_WAKE for GEN9+
- Change a style of macro naming in order to use lines as input.
- Update Todo comments.
v4: Add parentheses to macros to avoid precedence issues.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200607143614.185246-1-gwan-gyeong.mun@intel.com
We accidentally dropped matching for DVO_PORT_DPE from the VBT mapping
table when we refactored the function. Restore it.
Fixes: 4628142aec ("drm/i915/rkl: provide port/phy mapping for vbt")
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200606031803.3309624-1-matthew.d.roper@intel.com
This parameter is meant to be used when PSR issues are found as some
issues in the past was due wrong values set in VBT so this would be
a quick and easy way to ask users or for us to check if the issue is
due VBT values.
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200520212756.354623-1-jose.souza@intel.com
RKL doesn't have PSR2 HW tracking, it was replaced by software/manual
tracking. The driver is required to track the areas that needs update
and program hardware to send selective updates.
So until the software tracking is implemented, PSR2 needs to be disabled
for platforms without PSR2 HW tracking.
BSpec: 50422
BSpec: 50424
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200603211529.3005059-15-matthew.d.roper@intel.com
RKL uses DDI's A, B, TC1, and TC2 which need to map to combo PHY's A-D.
Bspec: 49181
Cc: Imre Deak <imre.deak@intel.com>
Cc: Aditya Swarup <aditya.swarup@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200603211529.3005059-6-matthew.d.roper@intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
As latest update we have now 2 voltage swing tables for DP over DKL
PHY with only one difference in Level 0 pre-emphasis 3.
So with 2 tables for DP is time to have one single function to return
all DKL voltage swing tables.
BSpec: 49292
Cc: Khaled Almahallawy <khaled.almahallawy@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Tested-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Reviewed-by: Khaled Almahallawy<khaled.almahallawy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200602205424.138143-1-jose.souza@intel.com
Previous patch didn't take into account all pipes
but only those in state, which could cause wrong
CDCLK conclcusions and calculations.
Also there was a severe issue with min_cdclk being
assigned to 0 every compare cycle.
Too bad this was found by me only after merge.
This could be also causing the issues in test, however
not clear - anyway marking this as fixing the
"Adjust CDCLK accordingly to our DBuf bw needs".
v2: - s/pipe/crtc->pipe/
- save a bit of instructions by
skipping inactive pipes, without
getting 0 DBuf slice mask for it.
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Fixes: cd19154608 ("drm/i915: Adjust CDCLK accordingly to our DBuf bw needs")
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200601173058.5084-1-stanislav.lisovskiy@intel.com
Certain combo PHYs act as a compensation master to other PHYs and need
to be initialized with a special irefgen bit in the PORT_COMP_DW8
register. Previously PHY A was the only compensation master (for PHYs
B & C), but RKL adds a fourth PHY which is slaved to PHY C instead.
Bspec: 49291
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Aditya Swarup <aditya.swarup@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200603211529.3005059-12-matthew.d.roper@intel.com
The pin mapping for the final two outputs varies according to which PCH
is present on the platform: with TGP the pins are remapped into the TC
range, whereas with CMP they stay in the traditional combo output range.
Bspec: 49181
Cc: Aditya Swarup <aditya.swarup@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200603211529.3005059-9-matthew.d.roper@intel.com
RKL uses the DDI A, DDI B, DDI USBC1, DDI USBC2 from the DE point of
view, so all DDI/pipe/transcoder register use these indexes to refer to
them. Combo phy and IO functions follow another namespace that we keep
as "enum phy". The VBT in theory would use the DE point of view, but
that does not happen in practice.
Provide a table to convert the child devices to the "correct" port
numbering we use. Now this is the output we get while reading the VBT:
DDIA:
[drm:intel_bios_port_aux_ch [i915]] using AUX A for port A (VBT)
[drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:275:DDI A]
[drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:275:DDI A]
[drm:intel_hdmi_init_connector [i915]] Using DDC pin 0x1 for port A (VBT)
DDIB:
[drm:intel_bios_port_aux_ch [i915]] using AUX B for port B (platform default)
[drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:291:DDI B]
[drm:intel_hdmi_init_connector [i915]] Using DDC pin 0x2 for port B (VBT)
DDI USBC1:
[drm:intel_bios_port_aux_ch [i915]] using AUX D for port D (VBT)
[drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:295:DDI D]
[drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:295:DDI D]
[drm:intel_hdmi_init_connector [i915]] Using DDC pin 0x3 for port D (VBT)
DDI USBC2:
[drm:intel_bios_port_aux_ch [i915]] using AUX E for port E (VBT)
[drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:306:DDI E]
[drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:306:DDI E]
[drm:intel_hdmi_init_connector [i915]] Using DDC pin 0x9 for port E (VBT)
Cc: Clinton Taylor <Clinton.A.Taylor@intel.com>
Cc: Aditya Swarup <aditya.swarup@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200603211529.3005059-7-matthew.d.roper@intel.com
The DP spec says:
"When the combination of the requested pre-emphasis level and
voltage swing exceeds the capability of a DPTX, the DPTX shall
set the pre-emphasis level according to the request and use the
highest voltage swing it can output with the given pre-emphasis level."
and
"When a DPTX reads a request beyond the limits of this Standard,
the DPTX shall set the pre-emphasis level according to the request
and set the highest voltage swing level it can output with the
given pre-emphasis level. If a DPTX is requested for 9.5dB of
pre-emphasis level (may be supported for a DPTX) and cannot support
that level, it shall set the pre-emphasis level to the next
highest level, 6dB."
Ie. we should first validate the pre-emphasis, and then select
the appropriate vswing for it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200512174145.3186-6-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
According to the DP spec supporting vswing 1 + preemph 2 is
mandatory. We don't have the hw settings for that though. In
order to pretend to follow the DP spec let's just select
vswing 0 + preemph 2 in this case (the DP spec says to use
the requested preemph in preference to the vswing when the
requested values aren't supported).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200512174145.3186-4-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
cpt/ppt support pre-emphasis level 3. Let's actually declare
support for it, instead of clamping things to level 2.
Also tweak the if-ladder in intel_dp_voltage_max() to match
intel_dp_pre_emphasis_max() to make it easier to compare them.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200512174145.3186-2-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Cometlake is a small refresh of Coffeelake, but since we have found out a
difference in the plaforms, we need to identify them as separate platforms.
Since we previously took Coffeelake/Cometlake as identical, update all
IS_COFFEELAKE() to also include IS_COMETLAKE().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200602140541.5481-1-chris@chris-wilson.co.uk
If an error is encountered during the DSI initialization setup, the
drm connector object also needs to be cleaned up along with the encoder.
The error can happen due to a missing mode in the VBT or for other
reasons.
v2: Rephrase the commit message to make it more clear.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200522202630.7604-1-vivek.kasireddy@intel.com
While the current locking/serialization of the global state
suffices for protecting the obj->state access and the actual
hardware reprogramming, we do have a problem with accessing
the old/new states during nonblocking commits.
The state computation and swap will be protected by the crtc
locks, but the commit_tails can finish out of order, thus also
causing the atomic states to be cleaned up out of order. This
would mean the commit that started first but finished last has
had its new state freed as the no-longer-needed old state by the
other commit.
To fix this let's just refcount the states. obj->state amounts
to one reference, and the intel_atomic_state holds extra references
to both its new and old global obj states.
Fixes: 0ef1905ecf ("drm/i915: Introduce better global state handling")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200527200245.13184-1-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
(cherry picked from commit f8c86ffa28)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
While the current locking/serialization of the global state
suffices for protecting the obj->state access and the actual
hardware reprogramming, we do have a problem with accessing
the old/new states during nonblocking commits.
The state computation and swap will be protected by the crtc
locks, but the commit_tails can finish out of order, thus also
causing the atomic states to be cleaned up out of order. This
would mean the commit that started first but finished last has
had its new state freed as the no-longer-needed old state by the
other commit.
To fix this let's just refcount the states. obj->state amounts
to one reference, and the intel_atomic_state holds extra references
to both its new and old global obj states.
Fixes: 0ef1905ecf ("drm/i915: Introduce better global state handling")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200527200245.13184-1-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Currently the plane property doesn't have support for YCBCR_BT2020,
which enables the corresponding color conversion mode on plane CSC.
Enabling the plane property for the planes for GLK & ICL+ platforms.
Also as per spec, update the Plane Color CSC from YUV601_TO_RGB709
to YUV601_TO_RGB601.
V2: Enabling support for YCBCT_BT2020 for HDR planes on
platforms GLK & ICL
V3: Refined the condition check to handle GLK & ICL+ HDR planes
Also added BT2020 handling in glk_plane_color_ctl.
V4: Combine If-else into single If
V5: Drop the checking for HDR planes and enable YCBCR_BT2020
for platforms GLK & ICL+.
V6: As per Spec, update PLANE_COLOR_CSC_MODE_YUV601_TO_RGB709
to PLANE_COLOR_CSC_MODE_YUV601_TO_RGB601 as per Ville's
feedback.
V7: Rebased
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200601073544.11291-1-kishore.kadiyala@intel.com
There's no reason for I915_MODE_FLAG_INHERITED to exist as a flag
anymore. Just make it a boolean.
v2: Deal with sanitize_watermarks()
CC: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200429103936.11850-1-ville.syrjala@linux.intel.com
Replace the use of mode->private_flags with a truly private bitmaks
in our own crtc state. We also need a copy in the crtc itself so the
vblank code can get at it. We already have scanline_offset in there
for a similar reason, as well as the vblank->hwmode which is assigned
via drm_calc_timestamping_constants(). Fortunately we now have a
nice place for doing the crtc_state->crtc copy in
intel_crtc_update_active_timings() which gets called both for
modesets and init/resume readout.
The one slightly iffy spot is the INHERITED flag which we want to
preserve until userspace/fb_helper does the first proper commit after
actually calling .detecti() on the connectors. Otherwise we don't have
the full sink capabilities (audio,infoframes,etc.) when .compute_config()
gets called and thus we will fail to enable those features when the
first userspace commit happens. The only internal commit we do prior to
that should be from intel_initial_commit() and there we can simply
preserve the INHERITED flag from the readout.
v2: Deal with INHERITED in sanitize_watermarks() as well
CC: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200429103904.11727-1-ville.syrjala@linux.intel.com
The drrs code dereferences mode->vrefresh via some really long chain
of structures/pointers. Couldn't get coccinelle to see through all
that so let's add some local variables to help it.
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200428171940.19552-3-ville.syrjala@linux.intel.com
drivers/gpu/drm/i915/display/intel_dsb.c:177 intel_dsb_reg_write() warn: variable dereferenced before check 'dsb' (see line 175)
Fixes: afeda4f3b1 ("drm/i915/dsb: Pre allocate and late cleanup of cmd buffer")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200524233900.25598-1-chris@chris-wilson.co.uk
Pre-allocate command buffer in atomic_commit using intel_dsb_prepare
function which also includes pinning and map in cpu domain.
No functional change is dsb write/commit functions.
Now dsb get/put function is removed and ref-count mechanism is
not needed. Below dsb api added to do respective job mentioned
below.
intel_dsb_prepare - Allocate, pin and map the buffer.
intel_dsb_cleanup - Unpin and release the gem object.
RFC: Initial patch for design review.
v2: included _init() part in _prepare(). [Daniel, Ville]
v3: dsb_cleanup called after cleanup_planes. [Daniel]
v4: dsb structure is moved to intel_crtc_state from intel_crtc. [Maarten]
v5: dsb get/put/ref-count mechanism removed. [Maarten]
v6: Based on review feedback following changes are added,
- replaced intel_dsb structure by pointer in intel_crtc_state. [Maarten]
- passing intel_crtc_state to dsp-api to simplify the code. [Maarten]
- few dsb functions prototype modified to simplify code.
v7: added few cosmetic changes suggested by Jani and null check for
crtc_state in dsb_cleanup removed as suggested by Maarten.
v8: changed the function parameter to intel_crtc_state* of
ivb_load_lut_ext_max() from intel_crtc. [Maarten]
v9: error handling improved in _write() and prepare(). [Maarten]
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200520130737.11240-1-animesh.manna@intel.com
Removed duplicate include and fixed comment > 80 chars.
v2: Added newline after system include and between functions
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200522131843.20477-1-stanislav.lisovskiy@intel.com
According to BSpec max BW per slice is calculated using formula
Max BW = CDCLK * 64. Currently when calculating min CDCLK we
account only per plane requirements, however in order to avoid
FIFO underruns we need to estimate accumulated BW consumed by
all planes(ddb entries basically) residing on that particular
DBuf slice. This will allow us to put CDCLK lower and save power
when we don't need that much bandwidth or gain additional
performance once plane consumption grows.
v2: - Fix long line warning
- Limited new DBuf bw checks to only gens >= 11
v3: - Lets track used Dbuf bw per slice and per crtc in bw state
(or may be in DBuf state in future), that way we don't need
to have all crtcs in state and those only if we detect if
are actually going to change cdclk, just same way as we
do with other stuff, i.e intel_atomic_serialize_global_state
and co. Just as per Ville's paradigm.
- Made dbuf bw calculation procedure look nicer by introducing
for_each_dbuf_slice_in_mask - we often will now need to iterate
slices using mask.
- According to experimental results CDCLK * 64 accounts for
overall bandwidth across all dbufs, not per dbuf.
v4: - Fixed missing const(Ville)
- Removed spurious whitespaces(Ville)
- Fixed local variable init(reduced scope where not needed)
- Added some comments about data rate for planar formats
- Changed struct intel_crtc_bw to intel_dbuf_bw
- Moved dbuf bw calculation to intel_compute_min_cdclk(Ville)
v5: - Removed unneeded macro
v6: - Prevent too frequent CDCLK switching back and forth:
Always switch to higher CDCLK when needed to prevent bandwidth
issues, however don't switch to lower CDCLK earlier than once
in 30 minutes in order to prevent constant modeset blinking.
We could of course not switch back at all, however this is
bad from power consumption point of view.
v7: - Fixed to track cdclk using bw_state, modeset will be now
triggered only when CDCLK change is really needed.
v8: - Lock global state if bw_state->min_cdclk is changed.
- Try getting bw_state only if there are crtcs in the commit
(need to have read-locked global state)
v9: - Do not do Dbuf bw check for gens < 9 - triggers WARN
as ddb_size is 0.
v10: - Lock global state for older gens as well.
v11: - Define new bw_calc_min_cdclk hook, instead of using
a condition(Manasi Navare)
v12: - Fixed rebase conflict
v13: - Added spaces after declarations to make checkpatch happy.
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200520150058.16123-1-stanislav.lisovskiy@intel.com
We quite often need now to iterate only particular dbuf slices
in mask, whether they are active or related to particular crtc.
v2: - Minor code refactoring
v3: - Use enum for max slices instead of macro
Let's make our life a bit easier and use a macro for that.
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200519131117.17190-6-stanislav.lisovskiy@intel.com
Checking with hweight8 if plane configuration had
changed seems to be wrong as different plane configs
can result in a same hamming weight.
So lets check the bitmask itself.
v2: Fixed "from" field which got corrupted for some weird reason
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200520145827.15887-1-stanislav.lisovskiy@intel.com
In Gen11+ whenever we might exceed DBuf bandwidth we might need to
recalculate CDCLK which DBuf bandwidth is scaled with.
Total Dbuf bw used might change based on particular plane needs.
Thus to calculate if cdclk needs to be changed it is not enough
anymore to check plane configuration and plane min cdclk, per DBuf
bw can be calculated only after wm/ddb calculation is done and
all required planes are added into the state. In order to keep
all min_cdclk related checks in one place let's extract it into
separate function, checking and modifying any_ms.
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200519131117.17190-3-stanislav.lisovskiy@intel.com
We need to calculate cdclk after watermarks/ddb has been calculated
as with recent hw CDCLK needs to be adjusted accordingly to DBuf
requirements, which is not possible with current code organization.
Setting CDCLK according to DBuf BW requirements and not just rejecting
if it doesn't satisfy BW requirements, will allow us to save power when
it is possible and gain additional bandwidth when it's needed - i.e
boosting both our power management and perfomance capabilities.
This patch is preparation for that, first we now extract modeset
calculation from modeset checks, in order to call it after wm/ddb
has been calculated.
v2: - Extract only intel_modeset_calc_cdclk from intel_modeset_checks
(Ville Syrjälä)
v3: - Clear plls after intel_modeset_calc_cdclk
v4: - Added r-b from previous revision to commit message
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200519131117.17190-2-stanislav.lisovskiy@intel.com
Since the number of platforms with this restriction are growing, let's
separate out the platform logic into a has_phy_misc() function.
Bspec: 50107
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200504225227.464666-11-matthew.d.roper@intel.com
RKL power wells are similar to TGL power wells, but have some important
differences:
* PG1 now has pipe A's VDSC (rather than sticking it in PG2)
* PG2 no longer exists
* DDI-C (aka TC-1) moves from PG1 -> PG3
* PG5 no longer exists due to the lack of a fourth pipe
Also note that what we refer to as 'DDI-C' and 'DDI-D' need to actually
be programmed as TC-1 and TC-2 even though this platform doesn't have TC
outputs.
Bspec: 49234
Cc: Imre Deak <imre.deak@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200504225227.464666-9-matthew.d.roper@intel.com
RKL only has five universal planes, plus a cursor. Since the
bottom-most universal plane is considered the primary plane, set the
number of sprites available on this platform to 4.
In general, the plane capabilities of the remaining planes stay the same
as TGL. However the NV12 Y-plane support moves down to the new top two
planes and now only the bottom three planes can be used for NV12 UV.
Bspec: 49181
Bspec: 49251
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200504225227.464666-8-matthew.d.roper@intel.com
The RKL platform has different memory characteristics from past
platforms. Update the values used by our memory bandwidth calculations
accordingly.
Bspec: 53998
Cc: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200504225227.464666-7-matthew.d.roper@intel.com
UAPI Changes:
- drm/i915: Show per-engine default property values in sysfs
By providing the default values configured into the kernel via sysfs, it
is much more convenient for userspace to restore those sane defaults, or
at least know what are considered good baseline. This is useful, for
example, to cleanup after any failed userspace prior to commencing new
jobs.
Cross-subsystem Changes:
- video/hdmi: Add Unpack only function for DRM infoframe
- Includes pull request gvt-next-2020-05-12
Driver Changes:
- Restore Cherryview back to full-ppgtt (Chris, Mika)
- Document locking guidelines for i915 (Chris, Daniel, Joonas)
- Fix GitLab #1746: Handle idling during i915_gem_evict_something busy loops (Chris)
- Display WA #1105: Require linear fb stride to be multiple of 512 bytes on
gen9/glk (Ville)
- Add Wa_14010685332 for ICP/ICL (Matt R)
- Restrict w/a 1607087056 for EHL/JSL (Swathi)
- Fix interrupt handling for DP AUX transactions on Tigerlake (Imre)
- Revert "drm/i915/tgl: Include ro parts of l3 to invalidate" (Mika)
- Fix HDC pipeline flush hardware bit on Gen12 (Mika)
- Flush L3 when flushing render on Gen12 (Mika)
- Invalidate aux table entries forcibly between BB on Gen12 (Mika)
- Add aux table invalidate for all engines on Gen12 (Mika)
- Force pte cacheline to main memory Gen8+ (Mika)
- Add and enable TGL+ SAGV support (Stanislav)
- Implement vm_ops->access on i915 mmaps for GDB (Chris, Kristian)
- Replace zero-length array with flexible-array (Gustavo)
- Improve batch buffer pool effectiveness to mitigate soft-rc6 hit (Chris)
- Remove wait priority boosting (Chris)
- Keep driver module referenced when PMU is active (Chris)
- Sanitize RPS interrupts upon resume (Chris)
- Extend pcode read timeout to 20 ms (Chris)
- Wait for ACT sent before enabling MST pipe (Ville)
- Extend support to async relocations to SNB (Chris)
- Remove CNL pre-prod workarounds (Ville)
- Don't enable WaIncreaseLatencyIPCEnabled when IPC is disabled (Sultan)
- Record the active CCID from before reset (Chris)
- Mark concurrent submissions with a weak-dependency (Chris)
- Peel dma-fence-chains for await to allow engine-to-engine sync (Lionel)
- Prevent using semaphores to chain up to external fences (Chris)
- Fix GLK watermark calculations (Ville)
- Emit await(batch) before MI_BB_START (Chris)
- Reset execlists registers before HWSP (Chris)
- Drop no-semaphore boosting in favor of fast timeslicing (Chris)
- Fix enabled infoframe states of lspcon (Gwan-gyeong)
- Program DP SDPs on pipe updates (Gwan-gyeong)
- Stop sending DP SDPs on ddi disable (Gwan-gyeong)
- Store CS timestamp frequency in Hz (Ville)
- Remove unused HAS_FWTABLE macro (Pascal)
- Use batchbuffer chaining for relocations to save ring space (Chris)
- Try different engines for relocs if MI ops not supported (Chris, Tvrtko)
- Lazily acquire the device wakeref for freeing objects (Chris)
- Streamline display code arithmetics around rounding etc. (Ville)
- Use bw state for per crtc SAGV evaluation (Stanislav)
- Track active_pipes in bw_state (Stanislav)
- Nuke mode.vrefresh usage (Ville)
- Warn if the FBC is still writing to stolen on removal (Chris)
- Added new PCode commands prepping for QGV rescricting (Stansilav)
- Stop holding onto the pinned_default_state (Chris)
- Propagate error from completed fences (Chris)
- Ignore submit-fences on the same timeline (Chris)
- Pull waiting on an external dma-fence into its routine (Chris)
- Replace the hardcoded I915_FENCE_TIMEOUT with Kconfig (Chris)
- Mark up the racy read of execlists->context_tag (Chris)
- Tidy up the return handling for completed dma-fences (Chris)
- Introduce skl_plane_wm_level accessor (Stanislav)
- Extract SKL SAGV checking (Stanislav)
- Make active_pipes check skl specific (Stanislav)
- Suspend tasklets before resume sanitization (Chris)
- Remove redundant exec_fence (Chris)
- Mark the addition of the initial-breadcrumb in the request (Chris)
- Transfer old virtual breadcrumbs to irq_worker (Chris)
- Read the DP SDPs from the video DIP (Gwan-gyeong)
- Program DP SDPs with computed configs (Gwan-gyeong)
- Add state readout for DP VSC and DP HDR Metadata Infoframe SDP
(Gwan-gyeong)
- Add compute routine for DP PSR VSC SDP (Gwan-gyeong)
- Use new DP VSC SDP compute routine on PSR (Gwan-gyeong)
- Restrict qgv points which don't have enough bandwidth. (Stanislav)
- Nuke pointless div by 64bit (Ville)
- Static checker code fixes (Nathan, Mika, Chris)
- Add logging function for DP VSC SDP (Gwan-gyeong)
- Include HDMI DRM infoframe, DP HDR metadata and DP VSC SDP in the
crtc state dump (Gwan-gyeong)
- Make timeslicing explicit engine property (Chris, Tvrtko)
- Selftest and debugging improvements (Chris)
- Align variable names with BSpec (Ville)
- Tidy up gen8+ breadcrumb emission code (Chris)
- Turn intel_digital_port_connected() in a vfunc (Ville)
- Use stashed away hpd isr bits in intel_digital_port_connected() (Ville)
- Extract i915_cs_timestamp_{ns_to_ticks,tick_to_ns}() (Ville)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200515160703.GA19043@jlahtine-desk.ger.corp.intel.com
Make sure to select the port's AUX power domain while holding the TC
port lock. The domain depends on the port's current TC mode, which may
get changed under us if we're not holding the lock.
This was left out from
commit 8c10e22626 ("drm/i915: Keep the TypeC port mode fixed for detect/AUX transfers")
Cc: <stable@vger.kernel.org> # v5.4+
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514204553.27193-1-imre.deak@intel.com
(cherry picked from commit ae9b6cfe13)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
After the function is no longer marked 'inline', there
is now a new warning pointing out that the only caller
is inside of an #ifdef:
drivers/gpu/drm/i915/display/intel_panel.c:493:12: warning: 'scale_user_to_hw' defined but not used [-Wunused-function]
493 | static u32 scale_user_to_hw(struct intel_connector *connector,
| ^~~~~~~~~~~~~~~~
Move the function itself into that #ifdef as well.
Fixes: 81b55ef1f4 ("drm/i915: drop a bunch of superfluous inlines")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200428213106.3139170-1-arnd@arndb.de
(cherry picked from commit 794bdcf71f)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
struct drm_device specific drm_WARN* macros include device information
in the backtrace, so we know what device the warnings originate from.
Prefer drm_WARN_ON over WARN_ON.
Conversion is done with below sementic patch:
@@
identifier func, T;
@@
func(...) {
...
struct drm_i915_private *T = ...;
<+...
-WARN_ON(
+drm_WARN_ON(&T->drm,
...)
...+>
}
@@
identifier func, T;
@@
func(struct intel_digital_port *T,...) {
+struct drm_i915_private *i915 = to_i915(T->base.base.dev);
<+...
-WARN_ON(
+drm_WARN_ON(&i915->drm,
...)
...+>
}
changes since v1:
- Add i915 local variable and use it in drm_WARN_ON (Jani)
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200504181600.18503-5-pankaj.laxminarayan.bharadiya@intel.com
struct drm_device specific drm_WARN* macros include device information
in the backtrace, so we know what device the warnings originate from.
Prefer drm_WARN* over WARN* calls.
changes since v1:
- Added dev_priv local variable and used it in drm_WARN* calls (Jani)
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200504181600.18503-4-pankaj.laxminarayan.bharadiya@intel.com
struct drm_device specific drm_WARN* macros include device information
in the backtrace, so we know what device the warnings originate from.
Prefer drm_WARN_ON over WARN_ON at places where struct i915_power_domains
struct is available.
Conversion is done with below sementic patch:
@@
identifier func, T;
@@
func(struct i915_power_domains *T,...) {
+ struct drm_i915_private *i915 = container_of(T, struct drm_i915_private, power_domains);
<+...
-WARN_ON(
+drm_WARN_ON(&i915->drm,
...)
...+>
}
changes since v1:
- Fix commit subject (Jani)
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200504181600.18503-2-pankaj.laxminarayan.bharadiya@intel.com
Make sure to select the port's AUX power domain while holding the TC
port lock. The domain depends on the port's current TC mode, which may
get changed under us if we're not holding the lock.
This was left out from
commit 8c10e22626 ("drm/i915: Keep the TypeC port mode fixed for detect/AUX transfers")
Cc: <stable@vger.kernel.org> # v5.4+
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514204553.27193-1-imre.deak@intel.com
I've checked a bunch of gen3/4 machines and all seem to have
consistent FSB frequency information in the CLKCFG register.
So let's read out hrawclk on all gen3+ machines. Although
apart from g4x/pnv aux/pps dividers we only really need this
for for i965g/gm cs timestamp increment.
The CLKCFG memory clock values seem less consistent but we
don't care about those here.
For posterity here's a list of CLKCFG vs. FSB dumps from
a bunch of machines (only missing lpt for a full set):
machine CLKCFG FSB
alv1 0x00001411 533
alv2 0x00000420 400 (Chris)
gdg1 0x20000022 800
gdg2 0x20000022 800
cst 0x00010043 666
blb 0x00002034 1333
pnv1 0x00000423 666
pnv2 0x00000433 666
965gm 0x00004342 800
946gz 0x00000022 800
965g 0x00000422 800
g35 0x00000430 1066
0x00000434 1333
ctg1 0x00644056 1066
ctg2 0x00644066 1066
elk1 0x00012420 1066
0x00012424 1333
0x00012436 1600
0x00012422 800
elk2 0x00012040 1066
For the mobile parts the chipset docs generally have these
documented to some degree (alv being the exception).
The two settings w/o any evidence are 0x5=400MHz on desktop
and 0x7=1333MHz on mobile. Though the mobile 1333MHz case
probably doesn't even exist since ctg is only documented
to go up to 1066MHz.
v2: Fix 400mhz readout for Chris's alv/celeron machine
Do a clean mobile vs. dekstop split since that's really
what seems to be going on
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514123838.3017-3-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Document the fact that we aren't reading out the actual FSB
frequency but rather just the state of the FSB straps.
Some BIOSen allow you to configure the two independently.
So if someone sets the two up in an inconsistent manner
we'll get the wrong answer here and thus will end up with
incorrect aux/pps clock dividers. Alas, proper docs are no
longer around so we can't do any better.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514123838.3017-2-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Looks like elk redefines some of the CLKCFG FSB values to
make room for 400 MHz FSB. The setting overlaps with one of
the 266MHz settings (which is even documented in the ctg docs,
and cofirmed to be correct on my ctg). So we limit the special
case to elk only.
Though it might also be that we have some kind of desktop vs.
mobile difference going on here as eg. both g35 and elk
use 0x0 for the 266 MHz setting, vs. 0x6 used by ctg). The
g35 doesn't let me select 400MHz for the FSB strap so can't
confirm which way it would go here. But anyways as it seems
only elk has the 400MHz option we shouldn't lose anything
by limiting the special case to it alone.
My earlier experiments on this appear to have been nonsense as
the comment I added claims that FSB strap of 400MHz results in
a value of 0x4, but I've now retested it and I definitely get a
value of 0x6 instead. So let's remove that bogus comment.
v2: s/_ELK/_ALT/ in the define in anticipation of a full
mobile vs. desktop CLKCFG split
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514123838.3017-1-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Encapsulate the dbuf state more by moving the pre/post
plane functions out from intel_display.c. We stick them
into intel_pm.c since that's where the rest of the code
lives for now.
Eventually we should add a new file for this stuff at which
point we also need to decide if it makes sense to even split
the wm code from the ddb code, or to keep them together.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200225171125.28885-11-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Add a global state to track the dbuf slices. Gets rid of all the nasty
coupling between state->modeset and dbuf recomputation. Also we can now
totally nuke state->active_pipe_changes.
dev_priv->wm.distrust_bios_wm still remains, but that too will get
nuked soon.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200225171125.28885-9-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
The low level dbuf slice code is rather inconsitent with its
functiona naming and organization. Make it more consistent.
Also share the enable/disable functions between all platforms
since the same code works just fine for all of them.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200225171125.28885-8-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Polish some of the dbuf code to give more meaningful debug
messages and whatnot. Also we can switch over to the per-device
debugs/warns at the same time.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200225171125.28885-7-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
After the function is no longer marked 'inline', there
is now a new warning pointing out that the only caller
is inside of an #ifdef:
drivers/gpu/drm/i915/display/intel_panel.c:493:12: warning: 'scale_user_to_hw' defined but not used [-Wunused-function]
493 | static u32 scale_user_to_hw(struct intel_connector *connector,
| ^~~~~~~~~~~~~~~~
Move the function itself into that #ifdef as well.
Fixes: 81b55ef1f4 ("drm/i915: drop a bunch of superfluous inlines")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200428213106.3139170-1-arnd@arndb.de
Put the overlay color conversion unit into 10bit mode if the
pipe isn't using the 8bit legacy gamma. Not 100% sure this is
what the intention of the bit was but makes at least some sense to
me.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191028113036.27553-4-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
As with the video sprites the colorkey is always specified
as 8bpc. For 10bpc primary plane formats we just ignore the
two lsbs of each component. For C8 we'll replicate the same
key to each chanel, which is what the hardware wants.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191028113036.27553-3-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Apparently the 128x128 and 256x256 ARGB cursor modes were
only added on LPT/CST.
While the display section of bspec isn't super clear on the
subject, it does highlight these two modes in a different
color, has a few changlog entries indicating the 256x256 mode
was added for a LPT DCN, and that the 128x128 mode was also
added later (though no DCN/platform note there).
The "device dependencies" bspec section does list the 256x256x32
as a new feature for LPT/CST, and goes on to mention that current
hw only has the 64x64x32 mode (which reinforces the notion that
the 128x128 mode was also added at the same time).
Testing on actual hardware confirms all of this. CI shows all
the 128x128 and 256x256 tests failing on GDG, and my ALV
definitely doesn't like them.
So we shall limit GDG/ALV to 64x64 only. And while at it
let's adjust the mobile gen2 case to list the two platforms
explicitly so that the if-ladder looks reasonably uniform.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191028113036.27553-2-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
According to BSpec 53998, we should try to
restrict qgv points, which can't provide
enough bandwidth for desired display configuration.
Currently we are just comparing against all of
those and take minimum(worst case).
v2: Fixed wrong PCode reply mask, removed hardcoded
values.
v3: Forbid simultaneous legacy SAGV PCode requests and
restricting qgv points. Put the actual restriction
to commit function, added serialization(thanks to Ville)
to prevent commit being applied out of order in case of
nonblocking and/or nomodeset commits.
v4:
- Minor code refactoring, fixed few typos(thanks to James Ausmus)
- Change the naming of qgv point
masking/unmasking functions(James Ausmus).
- Simplify the masking/unmasking operation itself,
as we don't need to mask only single point per request(James Ausmus)
- Reject and stick to highest bandwidth point if SAGV
can't be enabled(BSpec)
v5:
- Add new mailbox reply codes, which seems to happen during boot
time for TGL and indicate that QGV setting is not yet available.
v6:
- Increase number of supported QGV points to be in sync with BSpec.
v7: - Rebased and resolved conflict to fix build failure.
- Fix NUM_QGV_POINTS to 8 and moved that to header file(James Ausmus)
v8: - Don't report an error if we can't restrict qgv points, as SAGV
can be disabled by BIOS, which is completely legal. So don't
make CI panic. Instead if we detect that there is only 1 QGV
point accessible just analyze if we can fit the required bandwidth
requirements, but no need in restricting.
v9: - Fix wrong QGV transition if we have 0 planes and no SAGV
simultaneously.
v10: - Fix CDCLK corruption, because of global state getting serialized
without modeset, which caused copying of non-calculated cdclk
to be copied to dev_priv(thanks to Ville for the hint).
v11: - Remove unneeded headers and spaces(Matthew Roper)
- Remove unneeded intel_qgv_info qi struct from bw check and zero
out the needed one(Matthew Roper)
- Changed QGV error message to have more clear meaning(Matthew Roper)
- Use state->modeset_set instead of any_ms(Matthew Roper)
- Moved NUM_SAGV_POINTS from i915_reg.h to i915_drv.h where it's used
- Keep using crtc_state->hw.active instead of .enable(Matthew Roper)
- Moved unrelated changes to other patch(using latency as parameter
for plane wm calculation, moved to SAGV refactoring patch)
v12: - Fix rebase conflict with own temporary SAGV/QGV fix.
- Remove unnecessary mask being zero check when unmasking
qgv points as this is completely legal(Matt Roper)
- Check if we are setting the same mask as already being set
in hardware to prevent error from PCode.
- Fix error message when restricting/unrestricting qgv points
to "mask/unmask" which sounds more accurate(Matt Roper)
- Move sagv status setting to icl_get_bw_info from atomic check
as this should be calculated only once.(Matt Roper)
- Edited comments for the case when we can't enable SAGV and
use only 1 QGV point with highest bandwidth to be more
understandable.(Matt Roper)
v13: - Moved max_data_rate in bw check to closer scope(Ville Syrjälä)
- Changed comment for zero new_mask in qgv points masking function
to better reflect reality(Ville Syrjälä)
- Simplified bit mask operation in qgv points masking function
(Ville Syrjälä)
- Moved intel_qgv_points_mask closer to gen11 SAGV disabling,
however this still can't be under modeset condition(Ville Syrjälä)
- Packed qgv_points_mask as u8 and moved closer to pipe_sagv_mask
(Ville Syrjälä)
- Extracted PCode changes to separate patch.(Ville Syrjälä)
- Now treat num_planes 0 same as 1 to avoid confusion and
returning max_bw as 0, which would prevent choosing QGV
point having max bandwidth in case if SAGV is not allowed,
as per BSpec(Ville Syrjälä)
- Do the actual qgv_points_mask swap in the same place as
all other global state parts like cdclk are swapped.
In the next patch, this all will be moved to bw state as
global state, once new global state patch series from Ville
lands
v14: - Now using global state to serialize access to qgv points
- Added global state locking back, otherwise we seem to read
bw state in a wrong way.
v15: - Added TODO comment for near atomic global state locking in
bw code.
v16: - Fixed intel_atomic_bw_* functions to be intel_bw_* as discussed
with Jani Nikula.
- Take bw_state_changed flag into use.
v17: - Moved qgv point related manipulations next to SAGV code, as
those are semantically related(Ville Syrjälä)
- Renamed those into intel_sagv_(pre)|(post)_plane_update
(Ville Syrjälä)
v18: - Move sagv related calls from commit tail into
intel_sagv_(pre)|(post)_plane_update(Ville Syrjälä)
v19: - Use intel_atomic_get_bw_(old)|(new)_state which is intended
for commit tail stage.
v20: - Return max bandwidth for 0 planes(Ville)
- Constify old_bw_state in bw_atomic_check(Ville)
- Removed some debugs(Ville)
- Added data rate to debug print when no QGV points(Ville)
- Removed some comments(Ville)
v21, v22, v23: - Fixed rebase conflict
v24: - Changed PCode mask to use ICL_ prefix
v25: - Resolved rebase conflict
v26: - Removed redundant NULL checks(Ville)
- Removed redundant error prints(Ville)
v27: - Use device specific drm_err(Ville)
- Fixed parenthesis ident reported by checkpatch
Line over 100 warns to be fixed together with
existing code style.
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: Ville Syrjälä <ville.syrjala@intel.com>
Cc: James Ausmus <james.ausmus@intel.com>
[vsyrjala: Drop duplicate intel_sagv_{pre,post}_plane_update() prototypes
and drop unused NUM_SAGV_POINTS define]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514074853.9508-3-stanislav.lisovskiy@intel.com
Starting from TGL we need to have a separate wm0
values for SAGV and non-SAGV which affects
how calculations are done.
v2: Remove long lines
v3: Removed COLOR_PLANE enum references
v4, v5, v6: Fixed rebase conflict
v7: - Removed skl_plane_wm_level accessor from skl_allocate_pipe_ddb(Ville)
- Removed sagv_uv_wm0(Ville)
- can_sagv->use_sagv_wm(Ville)
v8: - Moved tgl_crtc_can_enable_sagv function up(Ville)
- Changed comment regarding pipe_wm usage(Ville)
- Call intel_can_enable_sagv and tgl_compute_sagv_wm only
for Gen12(Ville)
- Some sagv debugs removed(Ville)
- skl_print_wm_changes improvements(Ville)
- Do assignment instead of memcpy in
skl_pipe_wm_get_hw_state(Ville)
v9: - Removed can_sagv variable(Ville)
- Removed spurious line(Ville)
- Changed u32 to unsigned int as agreed(Ville)
- Assign sagv only for gen12 in
skl_pipe_wm_get_hw_state(Ville)
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
[vsyrjala: Remove the dead 'return false' from intel_crtc_can_enable_sagv()]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514074853.9508-2-stanislav.lisovskiy@intel.com
In order to use a common VSC SDP Colorimetry calculating code on PSR,
it uses a new psr vsc sdp compute routine.
Because PSR routine has its own scenario and timings of writing a VSC SDP,
the current PSR routine needs to have its own drm_dp_vsc_sdp structure
member variable on struct i915_psr.
In order to calculate colorimetry information, intel_psr_update()
function and intel_psr_enable() function extend a drm_connector_state
argument.
There are no changes to PSR mechanism.
v3: Replace a structure name to drm_dp_vsc_sdp from intel_dp_vsc_sdp
v4: Rebased
v8: Rebased
v10: When a PSR is enabled, it needs to add DP_SDP_VSC to
infoframes.enable.
It is needed for comparing between HW and pipe_state of VSC_SDP.
v11: If PSR is disabled by flag, it don't enable psr on pipe compute.
v12: Fix an inconsistent indenting
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-15-gwan-gyeong.mun@intel.com
In order to use a common VSC SDP Colorimetry calculating code on PSR,
it adds a compute routine for PSR VSC SDP.
As PSR routine can not use infoframes.vsc of crtc state, it also adds new
writing of DP SDPs (Secondary Data Packet) for PSR.
PSR routine has its own scenario and timings of writing a VSC SDP.
v3: Replace a structure name to drm_dp_vsc_sdp from intel_dp_vsc_sdp
v4: Use struct drm_device logging macros
v10: 1) Fix packing of VSC SDP where Pixel Encoding/Colorimetry Format is
not supported.
2) Change a checking of PSR state.
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-14-gwan-gyeong.mun@intel.com
Call intel_dp_set_infoframes(false) function on intel_ddi_post_disable_dp()
to make sure not to send VSC SDP and HDR Metadata Infoframe SDP.
v5: Polish commit message [Uma]
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-13-gwan-gyeong.mun@intel.com
Call intel_dp_set_infoframes() function on pipe updates to make sure
that we send VSC SDP and HDR Metadata Infoframe SDP (when applicable)
on fastsets.
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-12-gwan-gyeong.mun@intel.com
Compared to implementation of DP and HDMI's encoder->infoframes_enabled,
the lspcon's implementation returns its active state. (we expect enabled
infoframe states of HW.) It leads to pipe state mismatch error
when ddi_get_config is called.
Because the current implementation of lspcon is not ready to support
readout infoframes, we need to return 0 here.
In order to support readout to lspcon, we need to implement read_infoframe
and infoframes_enabled. And set_infoframes also have to set an appropriate
bit on crtc_state->infoframes.enable
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-11-gwan-gyeong.mun@intel.com
Added state readout for DP VSC SDP and enabled state validation
for DP VSC SDP.
v2: Minor style fix
v3: Replace a structure name to drm_dp_vsc_sdp from intel_dp_vsc_sdp
v4: Use struct drm_device logging macros
v10: Skip checking of VSC SDP when a crtc config has psr.
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-10-gwan-gyeong.mun@intel.com
In order to use computed config for DP SDPs (DP VSC SDP and DP HDR Metadata
Infoframe SDP), it replaces intel_dp_vsc_enable() function and
intel_dp_hdr_metadata_enable() function to intel_dp_set_infoframes()
function.
And it removes unused functions.
Before:
intel_dp_vsc_enable() and intel_dp_hdr_metadata_enable() compute sdp
configs and program sdp registers on enable callback of encoder.
After:
It separates computing of sdp configs and programming of sdp register.
The compute config callback of encoder calls computing sdp configs.
The enable callback of encoder calls programming sdp register.
v3: Rebased
v5: Polish commit message [Uma]
v10: Rebased
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-8-gwan-gyeong.mun@intel.com
Dump out the DP VSC SDP in the normal crtc state dump
v3: Replace a structure name to drm_dp_vsc_sdp from intel_dp_vsc_sdp
Use drm core's DP VSC SDP logging function
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-7-gwan-gyeong.mun@intel.com
Dump out the DP HDR Metadata Infoframe SDP in the normal crtc state dump.
HDMI Dynamic Range and Mastering (DRM) infoframe and DP HDR Metadata
Infoframe SDP use the same member variable in infoframes of crtc state.
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-6-gwan-gyeong.mun@intel.com
It adds code to read the DP SDPs from the video DIP and unpack them into
the crtc state.
It adds routines that read out DP VSC SDP and DP HDR Metadata Infoframe SDP
In order to unpack DP VSC SDP, it adds intel_dp_vsc_sdp_unpack() function.
It follows DP 1.4a spec. [Table 2-116: VSC SDP Header Bytes] and
[Table 2-117: VSC SDP Payload for DB16 through DB18]
In order to unpack DP HDR Metadata Infoframe SDP, it adds
intel_dp_hdr_metadata_infoframe_sdp_unpack(). And it follows DP 1.4a spec.
([Table 2-125: INFOFRAME SDP v1.2 Header Bytes] and
[Table 2-126: INFOFRAME SDP v1.2 Payload Data Bytes - DB0 through DB31])
and CTA-861-G spec. [Table-42 Dynamic Range and Mastering InfoFrame].
A naming rule and style of intel_read_dp_sdp() function references
intel_read_infoframe() function of intel_hdmi.c
v2: Minor style fix
v3: Replace a structure name to drm_dp_vsc_sdp from intel_dp_vsc_sdp
v4: Use struct drm_device logging macros
v5: Addressed review comments from Uma
- Polish commit message and comments
- Combine the if checks of sdp.HB2 and sdp.HB3
- Add 6bpc to unpacking of VSC SDP
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-3-gwan-gyeong.mun@intel.com
Driver Changes:
- Fix GitLab #1698: Performance regression with Linux 5.7-rc1 on
Iris Plus 655 and 4K screen (Chris)
- Add Wa_14011059788 for Tigerlake (Matt A)
- Add per ctx batchbuffer wa for timestamp for Gen12 (Mika)
- Use indirect ctx bb to load cmd buffer control value
from context image to avoid corruption (Mika)
- Enable DP Display Audio WA (Uma, Jani)
- Update forcewake firmware ranges for Icelake (Radhakrishna)
- Add missing deinitialization cases of load failure for display (Jose)
- Implement TC cold sequences for Icelake and Tigerlake (Jose)
- Unbreak enable_dpcd_backlight modparam (Lyude)
- Move the late flush_submission in retire to the end (Chris)
- Demote "Reducing compressed framebufer size" message to info (Peter)
- Push MST link retraining to the hotplug work (Ville)
- Hold obj->vma.lock over for_each_ggtt_vma() (Chris)
- Fix timeout handling during TypeC AUX power well enabling for ICL (Imre)
- Fix skl+ non-scaled pfit modes (Ville)
- Prefer soft-rc6 over RPS DOWN_TIMEOUT (Chris)
- Sanitize GT first before poisoning HWSP (Chris)
- Fix up clock RPS frequency readout (Chris)
- Avoid reusing the same logical CCID (Chris)
- Avoid dereferencing a dead context (Chris)
- Always enable busy-stats for execlists (Chris)
- Apply the aggressive downclocking to parking (Chris)
- Restore aggressive post-boost downclocking (Chris)
- Scrub execlists state on resume (Chris)
- Add debugfs attributes for LPSP (Ansuman)
- Improvements to kernel selftests (Chris, Mika)
- Add tiled blits selftest (Zbigniew)
- Fix error handling in __live_lrc_indirect_ctx_bb() (Dan)
- Add pre/post plane updates for SAGV (Stanislav)
- Add ICL PG3 PW ID for EHL (Anshuman)
- Fix Sphinx build duplicate label warning (Jani)
- Error log non-zero audio power refcount after unbind (Jani)
- Remove object_is_locked assertion from unpin_from_display_plane (Chris)
- Use single set of AUX powerwell ops for gen11+ (Matt R)
- Prefer drm_WARN_ON over WARN_ON (Pankaj)
- Poison residual state [HWSP] across resume (Chris, Tvrtko)
- Convert request-before-CS assertion to debug (Chris)
- Carefully order virtual_submission_tasklet (Chris)
- Check carefully for an idle engine in wait-for-idle (Chris)
- Only close vma we open (Chris)
- Trace RPS events (Chris)
- Use the RPM config register to determine clk frequencies (Chris)
- Drop rq->ring->vma peeking from error capture (Chris)
- Check preempt-timeout target before submit_ports (Chris)
- Check HWSP cacheline is valid before acquiring (Chris)
- Use proper fault mask in interrupt postinstall too (Matt R)
- Keep a no-frills swappable copy of the default context state (Chris)
- Add atomic helpers for bandwidth (Stanislav)
- Refactor setting dma info to a common helper from device info (Michael)
- Refactor DDI transcoder code for clairty (Ville)
- Extend PG3 power well ID to ICL (Anshuman)
- Refactor PFIT code for readability and future extensibility (Ville)
- Clarify code split between intel_ddi.c and intel_dp.c (Ville)
- Move out code to return the digital_port of the aux ch (Jose)
- Move rps.enabled/active and use of RPS interrupts to flags (Chris)
- Remove superfluous inlines and dead code (Jani)
- Re-disable -Wframe-address from top-level Makefile (Nick)
- Static checker and spelling fixes (Colin, Nathan)
- Split long lines (Ville)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200430124904.GA100924@jlahtine-desk.ger.corp.intel.com
Get rid of several platform specific variants of
intel_digital_port_connected() and just use the ISR bits we've
stashed away.
v2: Duplicate stuff to avoid exposing platform specific
functions across files (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200311155422.3043-4-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Let's get rid of the platform if ladders in
intel_digital_port_connected() and make it a vfunc. Now the if
ladders are at the encoder initialization which makes them a bit
less convoluted.
v2: Add forward decl for intel_encoder in intel_tc.h
v3: Duplicate stuff to avoid exposing platform specific
functions across files (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200311155422.3043-2-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200507185408.GA14561@embeddedor
Expose the hardcoded timeout for unsignaled foreign fences as a Kconfig
option, primarily to allow brave systems to disable the timeout and
solely rely on correct signaling.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Acked-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200509105021.12542-1-chris@chris-wilson.co.uk
UAPI Changes:
Cross-subsystem Changes:
* MAINTAINERS: restore alphabetical order; update cirrus driver
* Dcomuentation: document visionix, chronteli, ite vendor prefices; update
documentation for Chrontel CH7033, IT6505, IVO, BOE,
Panasonic, Chunghwa, AUO bindings; convert dw_mipi_dsi.txt
to YAML; remove todo item for drm_display_mode.hsync removal;
Core Changes:
* drm: add devm_drm_dev_alloc() for managed allocations of drm_device;
use DRM_MODESET_LOCK_ALL_*() in mode-object code; remove
drm_display_mode.hsync; small cleanups of unused variables,
compiler warnings and static functions
* drm/client: dual-lincensing: GPL-2.0 or MIT
* drm/mm: optimize tree searches in rb_hole_addr()
Driver Changes:
* drm/{many}: use devm_drm_dev_alloc(); don't use drm_device.dev_private
* drm/ast: don't double-assign to drm_crtc_funcs.set_config; drop
drm_connector_register()
* drm/bochs: drop drm_connector_register()
* drm/bridge: add support for Chrontel ch7033; fix stack usage with
old gccs; return error pointer in drm_panel_bridge_add()
* drm/cirrus: Move to tiny
* drm/dp_mst: don't use 2nd sideband tx slot; revert "Remove single tx
msg restriction"
* drm/lima: support runtime PM;
* drm/meson: limit modes wrt chipset
* drm/panel: add support for Visionox rm69299; fix clock on
boe-tv101wum-n16; fix panel type for AUO G101EVN10;
add support for Ivo M133NFW4 R0; add support for BOE
NV133FHM-N61; add support for AUO G121EAN01.4, G156XTN01.0,
G190EAN01
* drm/pl111: improve vexpress init; fix module auto-loading
* drm/stm: read number of endpoints from device tree
* drm/vboxvideo: use managed PCI functions; drop DRM_MTRR_WC
* drm/vkms: fix use-after-free in vkms_gem_create(); enable cursor
support by default
* fbdev: use boolean values in several drivers
* fbdev/controlfb: fix COMPILE_TEST
* fbdev/w100fb: fix double-free bug
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEchf7rIzpz2NEoWjlaA3BHVMLeiMFAl6ztuYACgkQaA3BHVML
eiMWaAgAvYpXvBqBfE/5jOTa1zWQUX9VMbmMDUqSAgec5r/HVHjmlbsDWkLff2XG
rH7T2shMNJwluoCleHfRFYUfyUWMmXoMgri1elnf4EgddmekLZ6vNQjtAYMRFUfL
7VegcFw5D5Z28uxK5YGnaaSQob34LvD8UTgvnCVfDQzCjcEzGYi1d9XELm7kTHje
dF2FOWPeF8FTqP0XHM8RrHNXW/pUPy9qErpmb2bWYBQp7ebkI2Q4p6IZIpRQm757
bnKPIdMEcy4BWMk1xtzjEYEb4bGSZhozJUWKFwpm/AHNvTrQCt9hn0GSVrXiqBcR
UKb42BRxEVR29C/4n10pUcnnQmmi+Q==
=yzZ9
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2020-05-07' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.8:
UAPI Changes:
Cross-subsystem Changes:
* MAINTAINERS: restore alphabetical order; update cirrus driver
* Dcomuentation: document visionix, chronteli, ite vendor prefices; update
documentation for Chrontel CH7033, IT6505, IVO, BOE,
Panasonic, Chunghwa, AUO bindings; convert dw_mipi_dsi.txt
to YAML; remove todo item for drm_display_mode.hsync removal;
Core Changes:
* drm: add devm_drm_dev_alloc() for managed allocations of drm_device;
use DRM_MODESET_LOCK_ALL_*() in mode-object code; remove
drm_display_mode.hsync; small cleanups of unused variables,
compiler warnings and static functions
* drm/client: dual-lincensing: GPL-2.0 or MIT
* drm/mm: optimize tree searches in rb_hole_addr()
Driver Changes:
* drm/{many}: use devm_drm_dev_alloc(); don't use drm_device.dev_private
* drm/ast: don't double-assign to drm_crtc_funcs.set_config; drop
drm_connector_register()
* drm/bochs: drop drm_connector_register()
* drm/bridge: add support for Chrontel ch7033; fix stack usage with
old gccs; return error pointer in drm_panel_bridge_add()
* drm/cirrus: Move to tiny
* drm/dp_mst: don't use 2nd sideband tx slot; revert "Remove single tx
msg restriction"
* drm/lima: support runtime PM;
* drm/meson: limit modes wrt chipset
* drm/panel: add support for Visionox rm69299; fix clock on
boe-tv101wum-n16; fix panel type for AUO G101EVN10;
add support for Ivo M133NFW4 R0; add support for BOE
NV133FHM-N61; add support for AUO G121EAN01.4, G156XTN01.0,
G190EAN01
* drm/pl111: improve vexpress init; fix module auto-loading
* drm/stm: read number of endpoints from device tree
* drm/vboxvideo: use managed PCI functions; drop DRM_MTRR_WC
* drm/vkms: fix use-after-free in vkms_gem_create(); enable cursor
support by default
* fbdev: use boolean values in several drivers
* fbdev/controlfb: fix COMPILE_TEST
* fbdev/w100fb: fix double-free bug
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20200507072503.GA10979@linux-uq9g
All these ROUNDING_FACTORs and whatnot are making this thing hard to
read. Get rid of them. And let's massage some of the fractions to
give us less questionable intermediate results and perhaps less
divisions.
Also looks like a good helping of 64bit math stuff is needed to
avoid some of overflows present in the current code. There
might still be a few overflows, namely when calculating
link_clks_available/samples_room (would require a huge hblank
though), and potentially when calculating hblank_rise (not sure
how large link_clks_active can get).
It looks like we're still not calculating exactly what the spec says
since we truncate tu_data and tu_line early. But I'm too lazy to
figure out if we could avoid that.
v2: Fix typo in commit msg (Uma)
Remove ROUNDING_FACTOR define (Uma)
s/5*link_clk+5*cdclk/5*(link_clk+cdclk)/ (Chris)
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200429185457.26235-3-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Since the code seems insistent on using the variable names from the
bspec formulat, let's be consistent and use those names for all
the things. For some reason 'link_clk' and 'lanes' were left out
in the code until now.
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200429185457.26235-2-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
mode.vrefresh is rounded to the nearest integer. You don't want to use
it anywhere that requires precision. Also I want to nuke it.
vtotal*vrefresh == 1000*clock/htotal, so let's use the latter.
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200429185457.26235-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Display WA #1105 says that FBC requires PLANE_STRIDE to be a multiple
of 512 bytes on gen9 and glk.
This is definitely true for glk as certain tests (such as
igt/kms_big_fb/linear-16bpp-rotate-0) are now failing when the
display resolution results in a plane stride which is not a
multiple of 512 bytes.
Curiously I was not able to reproduce this on a KBL. First I
suspected that our use of the FBC override stride explain this,
but after trying to use the override stride on glk the test
still failed. I did try both the old CHICKEN_MISC_4 way and
the new FBC_STRIDE way, neither had any effect on the result.
Anyways, we need this at least on glk. But let's trust the spec
and apply the w/a for all gen9 as well, despite being unable to
reproduce the problem.
v2: s/FBC_CHICKEN/FBC_STRIDE/ in commit msg
Cc: José Roberto de Souza <jose.souza@intel.com>
Fixes: 691f7ba58d ("drm/i915/display/fbc: Make fences a nice-to-have for GEN9+")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200429101034.8208-2-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
That is a preparation patch before next one where we
introduce old_bw_state and a bunch of other changes
as well.
In a review comment it was suggested to split out
at least that renaming into a separate patch, what
is done here.
v2: Removed spurious space
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200423075902.21892-8-stanislav.lisovskiy@intel.com
We need to calculate SAGV mask also in a non-modeset
commit, however currently active_pipes are only calculated
for modesets in global atomic state, thus now we will be
tracking those also in bw_state in order to be able to
properly access global data.
v2: - Removed pre/post plane SAGV updates from modeset(Ville)
- Now tracking active pipes in intel_can_enable_sagv(Ville)
v3: - lock global state if active_pipes change as well(Ville)
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200430195634.7666-1-stanislav.lisovskiy@intel.com
Future platforms require per-crtc SAGV evaluation
and serializing global state when those are changed
from different commits.
v2: - Add has_sagv check to intel_crtc_can_enable_sagv
so that it sets bit in reject mask.
- Use bw_state in intel_pre/post_plane_enable_sagv
instead of atomic state
v3: - Fixed rebase conflict, now using
intel_atomic_crtc_state_for_each_plane_state in
order to call it from atomic check
v4: - Use fb modifier from plane state
v5: - Make intel_has_sagv static again(Ville)
- Removed unnecessary NULL assignments(Ville)
- Removed unnecessary SAGV debug(Ville)
- Call intel_compute_sagv_mask only for modesets(Ville)
- Serialize global state only if sagv results change, but
not mask itself(Ville)
v6: - use lock global state instead of serialize(Ville)
v7: - use both global state lock and serialize depending on
if we need to change only global state or access hw
(Ville)
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: Ville Syrjälä <ville.syrjala@intel.com>
Cc: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200430191757.18206-1-stanislav.lisovskiy@intel.com
Let's just calculate the hsync rate on demand. No point in wasting
space storing it and risking the cached value getting out of sync
with reality.
v2: Move drm_mode_hsync() next to its only users
Drop the TODO
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com> #v1
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200428171940.19552-2-ville.syrjala@linux.intel.com
Pass the entire connector state to intel_{gmch,pch}_panel_fitting().
For now we just need to get at .scaling_mode but in the future we'll
want access to the margin properties as well.
v2: Deal with intel_dp_ycbcr420_config()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200422161917.17389-5-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Make things a bit more abstract by replacing the pch_pfit.pos/size
raw register values with a drm_rect. Makes it slighly more convenient
to eg. compute the scaling factors.
v2: Use drm_rect_init()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200422161917.17389-3-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Most of the pfit functions are of the form:
func()
{
if (pfit_enabled) {
...
}
}
Flip the pfit_enabled check around to flatten the functions.
And while we're touching all this let's do the usual
s/pipe_config/crtc_state/ replacement.
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200422161917.17389-2-ville.syrjala@linux.intel.com
Fix skl_update_scaler_crtc() to deal with different scaling
modes correctly. The current implementation assumes
DRM_MODE_SCALE_FULLSCREEN. Fortunately we don't expose any
border properties currently so the code does actually end
up doing the right thing (assigning a scaler for pfit).
The code does need to be fixed before any borders are
exposed.
Also we have redundant calls to skl_update_scaler_crtc() in
dp/hdmi .compute_config() which can be nuked. They were anyway
called before we had even computed the pfit state so were
basically nonsense. The real call we need to keep is in
intel_crtc_atomic_check().
v2: Deal witrh skl_update_scaler_crtc() in intel_dp_ycbcr420_config()
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200422161917.17389-1-ville.syrjala@linux.intel.com
Fix the check for when an AUX power well enabling timeout is expected on
a legacy TypeC port.
Fixes: 89e01caac6 ("drm/i915: Use single set of AUX powerwell ops for gen11+")
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200422123440.19522-1-imre.deak@intel.com
struct drm_device specific drm_WARN* macros include device information
in the backtrace, so we know what device the warnings originate from.
Prefer drm_WARN_ON over WARN_ON at places where struct drm_device
pointer can be extracted.
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200406112800.23762-8-pankaj.laxminarayan.bharadiya@intel.com
struct drm_device specific drm_WARN* macros include device information
in the backtrace, so we know what device the warnings originate from.
Prefer drm_WARN_ON over WARN_ON at places where struct drm_device
pointer can be extracted.
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200406112800.23762-5-pankaj.laxminarayan.bharadiya@intel.com
The early check for compressed_bpp being zero is too early, as it is hit
also when DSC is not enabled. Move the checks down to where the values
are actually needed. This is a paranoid check for a situation that
should not happen, so we don't really care about handling it gracefully
apart from not oopsing.
Fixes: 48b8b04c79 ("drm/i915/display: Enable DP Display Audio WA")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/1750
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200420131632.23283-1-jani.nikula@intel.com
Remove a number of inlines from .c files, and let the compiler decide
what's best. There's more to do, but need to start somewhere, and need
to start setting the example.
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200420140438.14672-2-jani.nikula@intel.com
AUX power wells sometimes need additional handling besides just
programming the specific power well registers:
* Type-C PHY's also require additional Type-C register programming
* ICL combo PHY's require additional workarounds
* TGL & EHL combo PHY's can be treated like any other power well
Today we have dedicated aux ops for the ICL combo PHY and Type-C cases.
This works fine, but means that when a new platform shows up with
identical general power well handling, but different types of PHYs on
its outputs, we have to define an entire new power well table for that
platform and can't just re-use the table from the earlier platform -- as
an example, see ehl_power_wells[], which is a subset of
icl_power_wells[], *except* that we need to specify different AUX ops
for the third display.
If we instead create a single set of top-level aux ops that will check
the PHY type and then dispatch to the appropriate handlers, we can get
more reuse out of our power well definitions. This allows us to
immediately eliminate ehl_power_wells[] and simply reuse the ICL table;
if future platforms follow the same general power well assignments as
either ICL or TGL, we'll be able to re-use those tables in the same way.
Note that I've only changed ICL+ platforms over to using the new icl_aux
ops; at this point it's unlikely that we'll have any new platforms that
re-use gen9 or earlier power well configurations.
v2:
- ICL_AUX_PW_TO_PHY() won't return the proper PHY for TBT AUX power
wells. But we know those wells will only used on Type-C outputs
anyway, so we can just check is is_tc_tbt flag in the condition.
(Jose).
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200415233435.3064257-2-matthew.d.roper@intel.com
We shouldn't try to do link retraining from the short hpd handler.
We can't take any modeset locks there so this is racy as hell.
Push the whole thing into the hotplug work like we do with SST.
We'll just have to adjust the SST retraining code to deal with
the MST encoders and multiple pipes.
TODO: I have a feeling we should just rip this all out and
do a full modeset instead. Stuff like port sync and the tgl+
MST master transcoder stuff maybe doesn't work well if we
try to retrain without following the proper modeset sequence.
So far haven't done any actual tests to confirm that though.
Cc: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200417152734.464-2-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Make intel_dp_check_mst_status() somewhat legible by humans.
Note that the return value of drm_dp_mst_hpd_irq() is always
either 0 or -ENOMEM, and we never did anything with the latter
so we can just ignore the whole thing.
We can also get rid of the direct drm_dp_mst_topology_mgr_set_mst(false)
call since returning -EINVAL causes the caller to do the very same call
for us.
Cc: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200417152734.464-1-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Pass the encoder all the way down to
intel_ddi_transcoder_func_reg_val_get(). Allows us eliminate the
intel_ddi_get_crtc_encoder() eyesore.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200417134720.16654-4-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Push the TRANS_DDI_FUNC_CTL into the encoder enable hook. The disable
is already there, and as a followup will enable us to pass the encoder
all the way down.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200417134720.16654-3-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jani Nikula <jani.nikula@intel.com>
No reason that I can see why we should enable TRANS_DDI_FUNC_CTL
before we set up the watermarks of configure the mbus stuff.
In fact reordering these seems to match the bspec sequence better,
and crucially will allow us to push the TRANS_DDI_FUNC_CTL enable
into the encoder enable hook as a followup.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200417134720.16654-2-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Since intel_ddi_enable_pipe_clock() was pushed down into the
encoder hooks we can pass on the encoder instead of having
to use intel_ddi_get_crtc_encoder().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200417134720.16654-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jani Nikula <jani.nikula@intel.com>
This was sort of annoying me:
random:~$ dmesg | tail -1
[523884.039227] [drm] Reducing the compressed framebuffer size. This may lead to less power savings than a non-reduced-size. Try to increase stolen memory size if available in BIOS.
random:~$ dmesg | grep -c "Reducing the compressed"
47
This patch makes it DRM_INFO_ONCE() just like the similar message
farther down in that function is pr_info_once().
Cc: stable@vger.kernel.org
Signed-off-by: Peter Jones <pjones@redhat.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/1745
Link: https://patchwork.freedesktop.org/patch/msgid/20180706190424.29194-1-pjones@redhat.com
[vsyrjala: Rebase due to per-device logging]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Looks like I accidentally made it so you couldn't force DPCD backlight
support on, whoops. Fix that.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes: 17f5d57915 ("drm/i915: Force DPCD backlight mode on X1 Extreme 2nd Gen 4K AMOLED panel")
Cc: Adam Jackson <ajax@redhat.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: "Ville Syrjälä" <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200413214407.1851002-1-lyude@redhat.com
We have some module unload/reload tests hitting an issue with i915
unbinding the component interface before the audio driver has properly
put the power. Log an error about it for ease of debugging. (Normally
this leads to a wakeref debug splat on the power well.)
Cc: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200417065132.23048-1-jani.nikula@intel.com
The variable test_result is being initialized with a value that is
never read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200417160829.112776-1-colin.king@canonical.com
Right now dp.regs.dp_tp_ctl/status are only set during the encoder
pre_enable() hook, what is causing all reads and writes to those
registers to go to offset 0x0 before pre_enable() is executed.
So if i915 takes the BIOS state and don't do a modeset any following
link retraing will fail.
In the case that i915 needs to do a modeset, the DDI disable sequence
will write to a wrong register not disabling DP 'Transport Enable' in
DP_TP_CTL, making a HDMI modeset in the same port/transcoder to
not light up the monitor.
So here for GENs older than 12, that have those registers fixed at
port offset range it is loading at encoder/port init while for GEN12
it will keep setting it at encoder pre_enable() and during HW state
readout.
Fixes: 4444df6e20 ("drm/i915/tgl: move DP_TP_* to transcoder")
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200414230442.262092-1-jose.souza@intel.com
This is a expected timeout of static TC ports not conneceted, so
not throwing warnings that would taint CI.
v3:
- moved checks to tc_phy_aux_timeout_expected()
v4:
- moved and add comments to tc_phy_aux_timeout_expected()
v5:
- only checking tc_legacy_port for TC ports
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200414194956.164323-8-jose.souza@intel.com
As described in "drm/i915/tc/icl: Implement TC cold sequences" users
of TC functions should held aux power well during access to avoid
read garbage due HW in TC cold state.
v3:
- renamed is_tc_cold_blocked() to assert_tc_cold_blocked()
- restored the removed 0xffffffff checks
Reviewed-by: Imre Deak <imre.deak@intel.com>
Tested-by: You-Sheng Yang <vicamo.yang@canonical.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200414194956.164323-7-jose.souza@intel.com
TC ports can enter in TCCOLD to save power and is required to request
to PCODE to exit this state before use or read to TC registers.
For TGL there is a new MBOX command to do that with a parameter to ask
PCODE to exit and block TCCOLD entry or unblock TCCOLD entry.
So adding a new power domain to reuse the refcount and only allow
TC cold when all TC ports are not in use.
v2:
- fixed missing case in intel_display_power_domain_str()
- moved tgl_tc_cold_request to intel_display_power.c
- renamed TGL_TC_COLD_OFF to TGL_TC_COLD_OFF_POWER_DOMAINS
- added all TC and TBT aux power domains to
TGL_TC_COLD_OFF_POWER_DOMAINS
v3:
- added one msec sleep when PCODE returns -EAGAIN
- added timeout of 5msec to not loop forever if
sandybridge_pcode_write_timeout() keeps returning -EAGAIN
v4:
- Made failure to block or unblock TC cold a error
- removed 5msec timeout, instead giving PCODE 1msec by up 3 times to
recover from the internal error
v5:
- only sleeping 1msec when ret is -EAGAIN
BSpec: 49294
Cc: Imre Deak <imre.deak@intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200414194956.164323-6-jose.souza@intel.com
As part of ICL TC cold exit sequences we need to request aux power
well before lock the access to TC ports, so skiping the
intel_tc_port_ref_held() check for TC legacy ports.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Tested-by: You-Sheng Yang <vicamo.yang@canonical.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200414194956.164323-5-jose.souza@intel.com
This is required for legacy/static TC ports as IOM is not aware of
the connection and will not trigger the TC cold exit.
Just request PCODE to exit TCCOLD is not enough as it could enter
again before driver makes use of the port, to prevent it BSpec states
that aux powerwell should be held.
So here embedding the TC cold exit sequence into ICL aux enable,
it will enable aux and then request TC cold to exit.
The TC cold block(exit and aux hold) and unblock was added to some
exported TC functions for the others and to access PHY registers,
callers should enable and keep aux powerwell enabled during access.
Also adding TC cold check and warnig in tc_port_load_fia_params() as
at this point of the driver initialization we can't request power
wells, if we get this warning we will need to figure out how to handle
it.
v2:
- moved ICL TC cold exit function to intel_display_power
- using dig_port->tc_legacy_port to only execute sequences for legacy
ports, hopefully VBTs will have this right
- fixed check to call _hsw_power_well_continue_enable()
- calling _hsw_power_well_continue_enable() unconditionally in
icl_tc_phy_aux_power_well_enable(), if needed we will surpress timeout
warnings of TC legacy ports
- only blocking TC cold around fia access
v3:
- added timeout of 5msec to not loop forever if
sandybridge_pcode_write_timeout() keeps returning -EAGAIN
returning -EAGAIN in in icl_tc_cold_exit()
- removed leftover tc_cold_wakeref
- added one msec sleep when PCODE returns -EAGAIN
v4:
- removed 5msec timeout, instead giving 1msec to whoever is using
PCODE to finish it up to 3 times
- added a comment about turn TC cold exit failure as a error in future
BSpec: 21750
Closes: https://gitlab.freedesktop.org/drm/intel/issues/1296
Cc: Imre Deak <imre.deak@intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200414194956.164323-4-jose.souza@intel.com
This is a preparation for ICL TC cold exit sequences.
v2:
- renamed new functions to hsw_power_well_enable_prepare()/complete()
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Tested-by: You-Sheng Yang <vicamo.yang@canonical.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200414194956.164323-3-jose.souza@intel.com
This is a similar function to intel_aux_power_domain() but it do not
care about TBT ports, this will be needed by ICL TC sequences.
v2:
- renamed to intel_legacy_aux_to_power_domain()
Cc: Imre Deak <imre.deak@intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Tested-by: You-Sheng Yang <vicamo.yang@canonical.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200414194956.164323-2-jose.souza@intel.com
Moving the code to return the digital port of the aux channel also
removing the intel_phy_is_tc() to make it generic.
digital_port will be needed in icl_tc_phy_aux_power_well_enable()
so adding it as a parameter to icl_tc_port_assert_ref_held().
While at at removing the duplicated call to icl_tc_phy_aux_ch() in
icl_tc_port_assert_ref_held().
v2:
- fixed build when DRM_I915_DEBUG_RUNTIME_PM is not set
- moved to before hsw_wait_for_power_well_enable() as it will be
needed by hsw_wait_for_power_well_enable() in a future patch
v4:
- fixed action of if (!dig_port), continue instead of return
Cc: You-Sheng Yang <vicamo@gmail.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Tested-by: You-Sheng Yang <vicamo.yang@canonical.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200414194956.164323-1-jose.souza@intel.com
Lets have a unified way to handle SAGV changes,
espoecially considering the upcoming Gen12 changes.
Current "standard" way of doing this in commit_tail
is pre/post plane updates, when everything which
has to be forbidden and not supported in new config
has to be restricted before update and relaxed after
plane update.
v2: - Removed unneeded returns(Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200415143911.10244-5-stanislav.lisovskiy@intel.com
Add correspondent helpers to be able to get old/new bandwidth
global state object.
v2: - Fixed typo in function call
v3: - Changed new functions naming to use convention proposed
by Jani Nikula, i.e intel_bw_* in intel_bw.c file.
v4: - Change function naming back to intel_atomic* pattern,
was decided to rename in a separate patch series.
v5: - Fix function naming to match existing practices(Ville)
v6: - Removed spurious whitespace
v7: - Removed bw_state NULL checks(Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200415143911.10244-3-stanislav.lisovskiy@intel.com
For certain DP VDSC bpp settings, hblank asserts before hblank_early,
leading to a bad audio state. Driver need to program "hblank early
enable" and "samples per line" parameters in AUDIO_CONFIG_BE
register.
This is Display Audio WA #1406928334 for 4k+VDSC usecase
applicable on DP encoders. Implemented the same.
v2: Fixed build failures on 32bit machine.
v3: Dropped u64, added helpers for sample room calculation,
other general comments as per Jani Nikula's feedback.
Also fixed connector type check (spotted by Anshuman)
v4: Addressed Jani Nikula and Kai's review comments.
v5: Addressed Anshuman's review comment and used crtc_* variable
to get timings.
v6: Dropped a redundant initialization.
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200416105419.9664-1-uma.shankar@intel.com
It requires a separate debugfs attribute to expose lpsp
status to user space, as there may be display less configuration
without any valid connected output, those configuration will not be
able to test lpsp status, if lpsp status exposed from a connector
based debugfs attribute.
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200415170555.15531-5-anshuman.gupta@intel.com
Add connector debugfs attributes for each intel
connector which is getting register.
v2:
- adding connector debugfs for each connector in
intel_connector_register() to fix CI failure for legacy connectors.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200415170555.15531-4-anshuman.gupta@intel.com
New i915_pm_lpsp igt solution approach relies on connector specific
debugfs attribute i915_lpsp_capability, it exposes whether an output is
capable of driving lpsp.
v2:
- CI fixup.
v3:
- register i915_lpsp_info only for supported connector. [Jani]
- use intel_display_power_well_is_enabled() instead of looking
inside power_well count. [Jani]
- fixes the lpsp capable conditional logic. [Jani]
- combined the lpsp capable and enable info. [Jani]
v4:
- Separate out connector based debugfs i915_lpsp_capability
lpsp enable status would be exposes by different entry. [Animesh]
v5:
- Add Platform Gen condition to add i915_lpsp_capability
and some cosmetic nitpick changes. [Animesh]
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200415170555.15531-3-anshuman.gupta@intel.com
Gen11 onwards PG3 is contains functions for pipe B,
external displays, and VGA. It make sense to add
a power well id with name ICL_DISP_PW_3 rather then
TGL_DISP_PW_3, Also PG3 power well id requires to
know if lpsp is enabled.
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200415170555.15531-2-anshuman.gupta@intel.com
As on ICL, we want to use the Type-C aux handlers for the TBT aux wells
to ensure the DP_AUX_CH_CTL_TBT_IO flag is set properly.
Fixes: 656409bbaf ("drm/i915/tgl: Add power well support")
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200415233435.3064257-1-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
The check was always succeeding even in case of a mismatch due to the
HDCP_STATUS_ENC bit being set. Make sure both bits are actually set.
Signed-off-by: Oliver Barta <oliver.barta@aptiv.com>
Fixes: 2320175feb ("drm/i915: Implement HDCP for HDMI")
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200328104100.12162-1-oliver.barta@aptiv.com
PLANE_CTL_FORMAT_AYUV is already supported, according to hardware
specification.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Bob Paauwe <bob.j.paauwe@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200407215546.5445-2-bob.j.paauwe@intel.com
Media decompression support should not be advertised on any display
planes for steppings A0-C0.
Bspec: 53273
Fixes: 2dfbf9d287 ("drm/i915/tgl: Gen-12 display can decompress surfaces compressed by the media engine")
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200414211118.2787489-3-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Replace the TGL/ICL specific platform checks with a more generic check
using INTEL_GEN(). Fixes bug with broken audio after S3 resume on JSL
platforms.
An initial version of state save and restore of AUD_FREQ_CNTRL register
was added for subset of platforms in commit 87c1694533
("drm/i915: save AUD_FREQ_CNTRL state at audio domain suspend"). The state
save has proven to work well and it is needed in newer platforms, so needs
to be extended. Although the logic is not in practise needed on GEN9/10
systems, follow the hardware specification and apply state and restore on
all gen9+ platforms.
Bspec: 49281
Link: https://github.com/thesofproject/linux/issues/1719
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200330144421.11632-1-kai.vehmanen@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
legacy:
- fix drm_local_map.offset type
ttm:
- temporarily disable hugepages to debug amdgpu problems.
prime:
- fix sg extraction
amdgpu:
- Various Renoir fixes
- Fix gfx clockgating sequence on gfx10
- RAS fixes
- Avoid MST property creation after registration
- Various cursor/viewport fixes
- Fix a confusing log message about optional firmwares
i915:
- Flush all the reloc_gpu batch (Chris)
- Ignore readonly failures when updating relocs (Chris)
- Fill all the unused space in the GGTT (Chris)
- Return the right vswing table (Jose)
- Don't enable DDI IO power on a TypeC port in TBT mode for ICL+ (Imre)
analogix_dp:
- probe fix
virtio:
- oob fix in object create
-----BEGIN PGP SIGNATURE-----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=ZTAf
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2020-04-10' of git://anongit.freedesktop.org/drm/drm
Pull more drm fixes from Dave Airlie:
"As expected, more fixes did turn up in the latter part of the week.
The drm_local_map build regression fix is here, along with temporary
disabling of the hugepage work due to some amdgpu related crashes.
Otherwise it's just a bunch of i915, and amdgpu fixes.
legacy:
- fix drm_local_map.offset type
ttm:
- temporarily disable hugepages to debug amdgpu problems.
prime:
- fix sg extraction
amdgpu:
- Various Renoir fixes
- Fix gfx clockgating sequence on gfx10
- RAS fixes
- Avoid MST property creation after registration
- Various cursor/viewport fixes
- Fix a confusing log message about optional firmwares
i915:
- Flush all the reloc_gpu batch (Chris)
- Ignore readonly failures when updating relocs (Chris)
- Fill all the unused space in the GGTT (Chris)
- Return the right vswing table (Jose)
- Don't enable DDI IO power on a TypeC port in TBT mode for ICL+ (Imre)
analogix_dp:
- probe fix
virtio:
- oob fix in object create"
* tag 'drm-next-2020-04-10' of git://anongit.freedesktop.org/drm/drm: (34 commits)
drm/ttm: Temporarily disable the huge_fault() callback
drm/bridge: analogix_dp: Split bind() into probe() and real bind()
drm/legacy: Fix type for drm_local_map.offset
drm/amdgpu/display: fix warning when compiling without debugfs
drm/amdgpu: unify fw_write_wait for new gfx9 asics
drm/amd/powerplay: error out on forcing clock setting not supported
drm/amdgpu: fix gfx hang during suspend with video playback (v2)
drm/amd/display: Check for null fclk voltage when parsing clock table
drm/amd/display: Acknowledge wm_optimized_required
drm/amd/display: Make cursor source translation adjustment optional
drm/amd/display: Calculate scaling ratios on every medium/full update
drm/amd/display: Program viewport when source pos changes for DCN20 hw seq
drm/amd/display: Fix incorrect cursor pos on scaled primary plane
drm/amd/display: change default pipe_split policy for DCN1
drm/amd/display: Translate cursor position by source rect
drm/amd/display: Update stream adjust in dc_stream_adjust_vmin_vmax
drm/amd/display: Avoid create MST prop after registration
drm/amdgpu/psp: dont warn on missing optional TA's
drm/amdgpu: update RAS related dmesg print
drm/amdgpu: resolve mGPU RAS query instability
...
This patch process phy compliance request by programming requested
vswing, pre-emphasis and test pattern.
v1: Initial patch.
v2: Fixes added during testing with test-scope. (Khaled/Clint/Manasi)
- pipe used as argument during registers programming instead of port.
- TRANS_CONF must be disable/enable as well during ddi disable/enable.
- harcoded PLTPAT 80 bit custom pattern as the DPR-100 does not set it
in the sink’s DPCDs
- TRANS_DDI_FUNC_CTL DDI_Select (Bits 27:30) need to reset/set during
disable/enable.
v3: used macros instead of numbers and some cosmetic changes. [Manasi]
Cc: Clinton Taylor <Clinton.A.Taylor@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200316103759.12867-8-animesh.manna@intel.com
These debugfs entry will help testapp to understand the test request
during dp phy compliance mode.
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200316103759.12867-6-animesh.manna@intel.com
During DP phy compliance auto test mode, sink will request
combination of different test pattern with differnt level of
vswing, pre-emphasis. Function added to prepare for it.
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200316103759.12867-5-animesh.manna@intel.com
vswing/pre-emphasis adjustment calculation is needed in processing
of auto phy compliance request other than link training, so have
made non-static function.
No functional change.
v1: initial patch.
v2:
- used "intel_dp" prefix in function name. (Jani)
- used array notation instead pointer for link_status. (Ville)
v3: Scrapped the initial patch, modified commit description accordingly.
- made non-static function and used intel_dp prefix. (Jani, Manasi)
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200316103759.12867-4-animesh.manna@intel.com
Convert all the DRM_* logging macros to the struct drm_device based
macros to provide device specific logging.
No functional changes.
Cc: Wambui Karuga <wambui.karugax@gmail.com>
Reviewed-by: Wambui Karuga <wambui.karugax@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200402114819.17232-8-jani.nikula@intel.com
Convert all the DRM_* logging macros to the struct drm_device based
macros to provide device specific logging.
No functional changes.
Cc: Wambui Karuga <wambui.karugax@gmail.com>
Reviewed-by: Wambui Karuga <wambui.karugax@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200402114819.17232-7-jani.nikula@intel.com
Convert all the DRM_* logging macros to the struct drm_device based
macros to provide device specific logging.
No functional changes.
Cc: Wambui Karuga <wambui.karugax@gmail.com>
Reviewed-by: Wambui Karuga <wambui.karugax@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200402114819.17232-5-jani.nikula@intel.com
Drive-by fix I noticed the other day - drm_dp_mst_has_audio() only ever
made sense back when we still had to validate ports before accessing
them in order to (attempt to) avoid NULL dereferences. Since we have
proper reference counting that guarantees we always can safely access
the MST port, there's no use in keeping this function around as all it
does is validate the port pointer before checking the audio status.
Note - drm_dp_mst_port->has_audio is technically protected by
drm_device->mode_config.connection_mutex, since it's only ever updated
from drm_dp_mst_get_edid(). Additionally, we change the declaration for
port in struct intel_connector to be properly typed, so we can directly
access it.
Changes since v1:
* Change type of intel_connector->port in a separate patch - Sean Paul
Cc: "Lee, Shawn C" <shawn.c.lee@intel.com>
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200406200646.1263435-2-lyude@redhat.com
The only reason for having this cast as void * before was because we
originally needed to use drm_dp_mst_get_port_validated() and friends in
order to (attempt to) safely access MST ports. However, we've since
improved how reference counting works with ports and mstbs such that we
can now rely on drm_dp_mst_port structs remaining in memory for as long
as the driver needs. This means we don't really need to cast this as
void* anymore, and can just access the struct directly.
We'll also need this for the next commit, so that we can remove
drm_dp_mst_port_has_audio().
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Sean Paul <sean@poorly.run>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200406200646.1263435-1-lyude@redhat.com
DDI ports have its encoders initialized with INTEL_OUTPUT_DDI type and
later eDP ports that have the type changed to INTEL_OUTPUT_EDP.
But for all other DDI ports it can drive HDMI or DP depending on what
user connects to the ports.
ehl_get_combo_buf_trans() and tgl_get_combo_buf_trans() was checking
for INTEL_OUTPUT_DP that was never true, causing wrong vswing tables
being used.
So here replacing the INTEL_OUTPUT_DP checks by the valid output types
that this functions receives as parameters. HDMI cases will be
correctly handled as it do not use encoder->type, instead it calls the
functions with INTEL_OUTPUT_HDMI as type parameter and HDMI don't have
retraining.
v2:
changed INTEL_OUTPUT_DDI to INTEL_OUTPUT_EDP and INTEL_OUTPUT_HDMI
Fixes: bd3cf6f7ce ("drm/i915/dp/tgl+: Update combo phy vswing tables")
Cc: Clinton A Taylor <clinton.a.taylor@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200330210044.130510-1-jose.souza@intel.com
(cherry picked from commit 70988115ac)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The DDI IO power well must not be enabled for a TypeC port in TBT mode,
ensure this during driver loading/system resume.
This gets rid of error messages like
[drm] *ERROR* power well DDI E TC2 IO state mismatch (refcount 1/enabled 0)
and avoids leaking the power ref when disabling the output.
Cc: <stable@vger.kernel.org> # v5.4+
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200330152244.11316-1-imre.deak@intel.com
(cherry picked from commit f77a2db27f)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
On TypeC ports if a sink deasserts/reasserts its HPD signal, generating
a hotplug interrupt without the sink getting unplugged/replugged from
the connector, there can be an up to 3 seconds delay until the AUX
channel gets functional. To avoid detection failures this delay causes
retry the detection for 5 seconds.
I noticed this on ICL/TGL RVPs and a DELL XPS 13 7390 ICL laptop.
References: https://gitlab.freedesktop.org/drm/intel/issues/1067
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200330095425.29113-2-imre.deak@intel.com
On TypeC connectors we need to retry the detection after hotplug events
for a longer time, so add a retry counter to support this. The next
patch will add detection retries on TypeC ports needing this.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200330095425.29113-1-imre.deak@intel.com
Move the final DP_TP_CTL frobbing of port sync to the master
encoder's enable hook. Now neatly out of sight from the high level
modeset code.
And thus we've eliminated all the special casing of port sync
in the high level modeset code.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200313164831.5980-14-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
We're going to want access to the atomic state for iterating
the slave crtcs when enabling the port sync master crtc. Pass
the atomic state all the way down.
The alternative would be yet another encoder hook which we'll
have to call after all the normal modeset stuff is done. Not
really a fan of yet another hook just for this.
Note that during readout state sanitation we are now going
to pass NULL as the atomic state since we don't have one.
We need to change that and then we can also s/crtc_state/crtc/
and s/conn_state/conn/ for the encoder hooks as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200313164831.5980-13-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Currently only port sync pipes do the sequence such that
we first do the modeset part for every pipe and then do
the plane/etc. updates. Let's follow that apporach for
all pipes in skl+ so that we can properly integrate the
port sync into the normal modeset flow.
v2: Remove now stale TODO of port sync slave entries[]
s/oldnew/new/
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200313164831.5980-12-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Don't assume there is just one port sync slave. We might have several.
v2: Fix unitialized new_crtc_state usage (José)
Fix clearing of modeset_pipes for slaves
s/oldnew/new/
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200313164831.5980-11-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Transcoder port sync was introduced to the hardware in BDW. We
can trivially enable it for SKL+ since the same codepaths are
already used for ICL+ port sync. The only difference is the actual
location of the bits we need to poke.
We leave BDW out (at least for now) since it uses different modeset
paths that haven't been adapted for port sync, and IIRC using the
feature would involve some extra workarounds we've not implemented.
Pre-BDW hardware does not support port sync so we'd have to tweak
the modeset sequence to start the pipes as close together as possible
and hope for the best. So far no one has seriously tried to implement
that.
Closes: https://gitlab.freedesktop.org/drm/intel/issues/27
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200313164831.5980-9-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
We have a bunch of code that would like to know which
CPU transcoders are actually present in the hardware. Rather than
use various ad-hoc methods let's just include a full bitmask in
the device info, alongside pipe_mask.
v2: Rebase
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200318170235.15176-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
-----BEGIN PGP SIGNATURE-----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=I0vz
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2020-04-01' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"This is the main drm pull request for 5.7-rc1.
Highlights:
- i915 enables Tigerlake by default
- i915 and amdgpu have initial OLED backlight support
[ Jani Nikula pipes up and points out that we've had a bunch of
"initial support" code for a long time already, but only now
Lyude made it actually work on real world machines ]
- vmwgfx add support to enable OpenGL 4 userspace
- zero length arrays are mostly removed.
Detailed summary:
new driver:
- tidss: TI Keystone platform display subsystem
core:
- new drm device warn macros
- mode config valid for memory constrained devices
- bridge bus format negotation
- consolidated fake vblank event handling
- dma_alloc related cleanups
- drop get_crtc callback
- dp: DP1.4 EDID corruption test
- EDID CEA detailed timings improvements
- relicense some code to dual GPL2/MIT
- convert core vblank support to per-crtc support
- rework drm_global_mutex
- bridge rework to allow omap_dss custom driver removeal
- remove drm_fb_helper connector interrfaces
- zero-length array removal
scheduler:
- support for modifying the sched list
- revert job distribution optimization
- helper to pick least loaded scheduler
- race condition fix
mst:
- various fixes
- remove register_connector callback
i915:
- uapi to allows userspace specific CS ring buffer sizes
- Tigerlake enablement patches + Tigerlake enabled by default
- new sysfs entries for engine properties
- display/logging refactors
- eDP/DP fixes for DPCD
- Gen7 back to aliasing-ppgtt
- Gen8+ irq refactor
- Avoid globals
- GEM locking fixes and simplifications
- Ice Lake and Elkhart Lake fixes and workarounds
- Baytrail/Haswell instability fix
- GVT - VFIO edid better support
amdgpu:
- Rework VM update handling in preparation for HMM support
- drm load/unload removal fixups
- USB-C PD firmware updates
- HDCP srm support
- Navi/renoir PM watermark fixes
- OLED panel support
- Optimize debugging vram access
- Use BACO for runtime pm
- DC clock programming optimizations and fixes
- PSP fw loading sequence updates
- Drop DRIVER_USE_AGP
- Remove legacy drm load and unload callbacks
- ACP Kconfig fix
- Lots of fixes across the driver
amdkfd:
- runtime pm support
- more gfx config details in amdgpu
radeon:
- drop DRIVER_USE_AGP
vmwgfx:
- Disable DMA when SEV encryption in use
- Shader Model 5 support - needed for GL4 support
msm:
- DPU resource manager refactor
- dpu using atomic global state
mediatek:
- MT8183 DPI support
etnaviv:
- out-of-bounds read fix
- expose feature flags for GC400 STM32MP1 SoC
- runtime suspend entry fix
- dma32 zone fix
hisilicon:
- mode selection fixes
meson:
- YUV420 support
lima:
- add support for heap buffers
tinydrm:
- removal of owner field
- explicit DT dependency removal
- YAML schema conversion
tegra:
- misc cleanups
tidss:
- new driver
virtio:
- better batching of notifications to host
- memory handling reworked
- shmem + gpu context fixes
hibmc:
- add gamma_set support
- improve DPMS support
pl111:
- Integrator IM-PD1 support
sun4i:
- LVDS support for A20 + A33
- DSI panel handling improvements"
* tag 'drm-next-2020-04-01' of git://anongit.freedesktop.org/drm/drm: (1537 commits)
drm/i915/display: Fix mode private_flags comparison at atomic_check
drm/i915/gt: Stage the transfer of the virtual breadcrumb
drm/i915/gt: Select the deepest available parking mode for rc6
drm/i915: Avoid live-lock with i915_vma_parked()
drm/i915/gt: Treat idling as a RPS downclock event
drm/i915/gt: Cancel a hung context if already closed
drm/i915: Use explicit flag to mark unreachable intel_context
drm/amdgpu: don't try to reserve training bo for sriov (v2)
drm/amdgpu/smu11: add support for SMU AC/DC interrupts
drm/amdgpu/swSMU: handle manual AC/DC notifications
drm/amdgpu/swSMU: handle DC controlled by GPIO for navi1x
drm/amdgpu/swSMU: set AC/DC mode based on the current system state (v2)
drm/amdgpu/swSMU: correct the bootup power source for Navi1X (v2)
drm/amdgpu/swSMU: use the smu11 power source helper for navi1x
drm/amdgpu/smu11: add a helper to set the power source
drm/amd/swSMU: add callback to set AC/DC power source (v2)
drm/scheduler: fix rare NULL ptr race
drm/amdgpu: fix the coverage issue to clear ArcVPGRs
drm/amd/display: Fix pageflip event race condition for DCN.
drm/[radeon|amdgpu]: Remove HAINAN board from max_sclk override check
...
Specification was updated with vswing tables for different
configurations.
Also reordering icl_mg_phy_ddi_buf_trans struct to match table order.
BSpec: 21735
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Clinton Taylor <clinton.a.taylor@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200330210044.130510-3-jose.souza@intel.com
DDI ports have its encoders initialized with INTEL_OUTPUT_DDI type and
later eDP ports that have the type changed to INTEL_OUTPUT_EDP.
But for all other DDI ports it can drive HDMI or DP depending on what
user connects to the ports.
ehl_get_combo_buf_trans() and tgl_get_combo_buf_trans() was checking
for INTEL_OUTPUT_DP that was never true, causing wrong vswing tables
being used.
So here replacing the INTEL_OUTPUT_DP checks by the valid output types
that this functions receives as parameters. HDMI cases will be
correctly handled as it do not use encoder->type, instead it calls the
functions with INTEL_OUTPUT_HDMI as type parameter and HDMI don't have
retraining.
v2:
changed INTEL_OUTPUT_DDI to INTEL_OUTPUT_EDP and INTEL_OUTPUT_HDMI
Fixes: bd3cf6f7ce ("drm/i915/dp/tgl+: Update combo phy vswing tables")
Cc: Clinton A Taylor <clinton.a.taylor@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200330210044.130510-1-jose.souza@intel.com
The DDI IO power well must not be enabled for a TypeC port in TBT mode,
ensure this during driver loading/system resume.
This gets rid of error messages like
[drm] *ERROR* power well DDI E TC2 IO state mismatch (refcount 1/enabled 0)
and avoids leaking the power ref when disabling the output.
Cc: <stable@vger.kernel.org> # v5.4+
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200330152244.11316-1-imre.deak@intel.com
Use the recently introduced encoder .compute_config_late() hook to
do the MST master transcoder assignment. Avoids having to do it
in a funny way before we know the CPU transcoder of each pipe.
And now we can also properly use hw.active instead of uapi.active
since it too has been calculated earlier for everyone.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200313164831.5980-2-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Not sure why this thing is trying to avoid declaring the proper
type for these pointers. But since these are used only once let's
just get rid of the local variable entirely.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310202752.28454-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Commit 632f3ab95f ("drm/i915/audio: add codec wakeup override
enabled/disable callback"), added logic to toggle Codec Wake on gen9.
This is used by audio driver when it resets the HDA controller.
It seems explicit toggling of the wakeline can help to fix problems
with probe failing on some gen12 platforms. And based on specs, there
is no reason why this programming sequence should not be applied to all
gen9+ platforms. No side-effects are seen on gen10/11. So apply
the wake-logic to all gen9+ platforms.
Link: https://github.com/thesofproject/linux/issues/1847
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200324153212.6303-1-kai.vehmanen@linux.intel.com
This patch fixes the private_flags of mode to be checked and
compared against uapi.mode and not from hw.mode. This helps
properly trigger modeset at boot if desired by driver.
It helps resolve audio_codec initialization issues if display
is connected at boot. Initial discussion on this issue has happened
on below thread:
https://patchwork.freedesktop.org/series/74828/
v2: No functional change. Fixed the Closes tag and added
Maarten's RB.
v3: Added Fixes tag.
Cc: Ville Syrjä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: Souza, Jose <jose.souza@intel.com>
Fixes: 58d124ea27 ("drm/i915: Complete crtc hw/uapi split, v6.")
Closes: https://gitlab.freedesktop.org/drm/intel/issues/1363
Suggested-by: Ville Syrjä <ville.syrjala@linux.intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: SweeAun Khor <swee.aun.khor@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200326125111.11081-1-uma.shankar@intel.com
(cherry picked from commit d5e5670592)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
This patch fixes the private_flags of mode to be checked and
compared against uapi.mode and not from hw.mode. This helps
properly trigger modeset at boot if desired by driver.
It helps resolve audio_codec initialization issues if display
is connected at boot. Initial discussion on this issue has happened
on below thread:
https://patchwork.freedesktop.org/series/74828/
v2: No functional change. Fixed the Closes tag and added
Maarten's RB.
v3: Added Fixes tag.
Cc: Ville Syrjä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: Souza, Jose <jose.souza@intel.com>
Fixes: 58d124ea27 ("drm/i915: Complete crtc hw/uapi split, v6.")
Closes: https://gitlab.freedesktop.org/drm/intel/issues/1363
Suggested-by: Ville Syrjä <ville.syrjala@linux.intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: SweeAun Khor <swee.aun.khor@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200326125111.11081-1-uma.shankar@intel.com
Avoid using the uninitialised len along the impossible error path to
shut the compiler up:
drivers/gpu/drm/i915/display/intel_dp.c:4928 intel_write_dp_sdp() error: uninitialized symbol 'len'.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200325140754.12636-1-chris@chris-wilson.co.uk
We've migrated all the heavy users over to the intel_gt, and can finally
drop the last few users and with that the mirror in dev_priv->engine[].
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Andi Shyti <andi.shyti@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200325234803.6175-1-chris@chris-wilson.co.uk
dGFX has local memory so it does not have aperture or support
CPU fences but even for iGFX it have a small number of fences.
As replacement for fences to track frontbuffer modifications by CPU
we have a software tracking that is already in used by FBC and PSR.
PSR don't support fences so it shows that this tracking is reliable.
So lets make fences a nice-to-have to activate FBC for GEN9+, this
will allow us to enable FBC for dGFXs and iGFXs even when there is no
available fence.
We do not set fences to rotated planes but FBC only have restrictions
against 16bpp, so adding it here.
Also adding a new check for the tiling format, fences are only set
to X and Y tiled planes but again FBC don't have any restrictions
against tiling so adding linear as supported as well, other formats
should be added after tested but IGT only supports drawing in thse
3 formats.
intel_fbc_hw_tracking_covers_screen() maybe can also have the same
treatment as fences but BSpec is not clear if the size limitation is
for hardware tracking or general use of FBC and I don't have a 5K
display to test it, so keeping as is for safety.
v2:
- Added tiling and pixel format rotation checks
- Changed the GEN version not requiring fences to 11 from 9, DDX
needs some changes but it don't have support for GEN11+
v3:
- Changed back to GEN9+
- Moved GEN test to inside of tiling_is_valid()
v4:
- moved rotation check to its own functions
v5:
- renamed rotations_is_valid to rotation_is_valid
- moved pre-g4x rotation check to rotation_is_valid()
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200319211535.114625-1-jose.souza@intel.com
On dsi cmd mode we do not receive vblanks instead
we would get TE and these flags indicate TE is expected on
which port.
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200312053841.2794-6-vandita.kulkarni@intel.com
If the GOP has programmed periodic command mode,
we need to disable that which would need a
deconfigure and configure sequence.
v2: Fix sparse error, pass only intel_dsi (Jani)
v3: Use intel_de_read
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200312053841.2794-5-vandita.kulkarni@intel.com
Adding TE flags and periodic command mode flags
as part of private flags to indicate what TE interrupts
we would be getting instead of vblanks in case of mipi dsi
command mode.
v2: Add TE flag description (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200312053841.2794-4-vandita.kulkarni@intel.com
Transcoder timing calculation differ for command mode.
v2: Use is_vid_mode, and use same I915_WRITE (Jani)
v3: Adjust the calculations to reflect dsc compression ratio
v4: Rearrange the vertical and horizontal timing calc, optimize
local variables usage. (Jani)
v5: Fix the values used for calculation, use afe_clk for
byte clock calculation, use intel_de_write/read (Jani)
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200312053841.2794-3-vandita.kulkarni@intel.com
Configure the transcoder to operate in TE GATE command mode
and take TE events from GPIO.
Also disable the periodic command mode, that GOP would have
programmed.
v2: Disable util pin (Jani)
v3: Use intel_de_write (Jani)
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200312053841.2794-2-vandita.kulkarni@intel.com
Few edp panels like Sharp is triggering short and long
hpd pulse after panel is getting powered off.
Currently driver is already ignoring long pulse for eDP
panel but in order to process the short pulse, it turns on
the VDD which requires panel power_cycle_delay + panel_power_on_delay
these delay on Sharp panel introduced the responsiveness overhead
of 800ms in the modeset sequence and as well is in suspend
sequence.
Ignoring any short pulse if panel is powered off.
FIXME: It requires to wait for panel_power_off delay in order
to check the panel power status due to pps_lock because panel triggers
short pulse immediately after writing PP_OFF to PP_CTRL register and
wait_panel_off waits for panel_power_off delay with pps_lock held.
This still creates responsiveness overhead of panel_power_off delay.
v2:
- checking vdd along with panel power to ignore the hpd. [Jani,Ville]
v3:
- safer side check to ignore the long hpd when eDP have power,
adding type of hpd to debug log. [Jani]
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200318081837.23983-1-anshuman.gupta@intel.com
We only consider crtc_state->enable when initially calculating plane
visibility. Later on we try to override the plane's state to invisible
if the crtc is in DPMS off state (crtc_state->active==false).
Unfortunately the code doing that only updates the plane_state.visible
flag and the crtc_state.active_planes bimask, but forgets to update
some of the other plane bitmasks stored in the crtc_state. Namely
crtc_state.nv12_planes is left set up based on the original visibility
check which makes icl_check_nv12_planes() pick a slave plane for the
flagged plane in the bitmask. Later on we hit the watermark code
which sees a plane with a slave assigned and it then makes the
logical assumption that the master plane must itself be visible.
Since the master's plane_state.visible flag was already cleared
we get a WARN.
Fix the problem by clearing all the plane bitmasks for DPMS off.
This is more or less the wrong approach and instead we should
calculate all the plane related state purely based crtc_state->enable
(to guarantee that the subsequent DPMS on can't fail). However in
the past we definitely had some roadblocks to making that happen.
Not sure how many are left these days, but let's stick to the current
approach since it's a much simpler fix to the immediate problem
(the WARN).
v2: Keep the visible=false, it's important (Rodrigo)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200318174515.31637-1-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
It adds routines that write DP VSC SDP and DP HDR Metadata Infoframe SDP.
In order to pack DP VSC SDP, it adds intel_dp_vsc_sdp_pack() function.
It follows DP 1.4a spec. [Table 2-116: VSC SDP Header Bytes] and
[Table 2-117: VSC SDP Payload for DB16 through DB18]
In order to pack DP HDR Metadata Infoframe SDP, it adds
intel_dp_hdr_metadata_infoframe_sdp_pack() function.
And it follows DP 1.4a spec.
([Table 2-125: INFOFRAME SDP v1.2 Header Bytes] and
[Table 2-126: INFOFRAME SDP v1.2 Payload Data Bytes - DB0 through DB31])
and CTA-861-G spec. [Table-42 Dynamic Range and Mastering InfoFrame].
A mechanism and a naming rule of intel_dp_set_infoframes() function
references intel_encoder->set_infoframes() of intel_hdmi.c .
VSC SDP is used for PSR and Pixel Encoding and Colorimetry Formats cases.
Because PSR routine has its own routine of writing a VSC SDP, when the PSR
is enabled, intel_dp_set_infoframes() does not write a VSC SDP.
v3:
- Explicitly disable unused DIPs (AVI, GCP, VS, SPD, DRM. They will be
used for HDMI), when intel_dp_set_infoframes() function will be called.
- Replace a structure name to drm_dp_vsc_sdp from intel_dp_vsc_sdp.
v4: Use struct drm_device logging macros
v5:
- use intel_de_*() functions for register access
- Addressed review comments from Uma
Polish commit message and comments
Add 6bpc to packing of VSC SDP
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200211074657.231405-5-gwan-gyeong.mun@intel.com
It stores computed dp hdr metadata infoframe sdp to infoframes.drm of
crtc state. It referenced intel_hdmi_compute_drm_infoframe().
While computing, we'll also fill out the infoframes.enable bitmask
appropriately.
v2: Wrap a long line.
v4: Use struct drm_device logging macros
v5: Fix typo [Uma]
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200211074657.231405-4-gwan-gyeong.mun@intel.com
In order to support state readout for DP VSC SDP, we need to have a
structure which holds DP VSC SDP payload data such as
"union hdmi_infoframe drm" which is used for DRM infoframe.
It adds a struct drm_dp_vsc_sdp vsc to intel_crtc_state.infoframes.
And it stores computed dp vsc sdp to infoframes.vsc of crtc state.
While computing we'll also fill out the inforames.enable bitmask
appropriately.
The compute routine follows DP 1.4 spec [Table 2-117: VSC SDP Payload for
DB16 through DB18].
v3: Replace a structure name to drm_dp_vsc_sdp from intel_dp_vsc_sdp
v5:
- Rebased
- Add warning where a bpc is 6 and a pixel format is RGB.
v7: Fix the wrong check of combination bpc 6 and RGB pixelformat
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200211074657.231405-3-gwan-gyeong.mun@intel.com
On i915 we have a new UAPI to allow userspace to specify CS ring buffer size on
construction (I915_CONTEXT_PARAM_RINGSIZE) and also new sysfs entries exposing
various engine properties
GVT Changes:
VFIO edid getting expanded to all platforms and a big cleanup around attr
group, unused vblank complete, kvmgt, Intel engine and dev_priv usages.
i915 Changes:
- new UAPI to allow userspace to specify CS ring buffer size on construction
(I915_CONTEXT_PARAM_RINGSIZE) - (Chris)
- New sysfs entries exposing various engine properties (Chris)
- Tiger Lake is out of require_force_probe protection (Jose)
- Changes in many places around active requests, reset and heartbeat (Chris)
- Stop assigning drm-dev_private pointer (Jani)
- Many code refactor in many places, including intel_modeset_init,
increasing use of intel_uncore_*, vgpu, and gvt stuff (Jani)
- Fixes around display pipe iterators (Anshuman)
- Tigerlake enabling work (Matt Ropper, Matt Atwood, Ville, Lucas, Daniele,
Jose, Anusha, Vivek, Swathi, Caz. Kai)
- Code clean-up like reducing use of drm/i915_drv.h, removing unused
registers, removing garbage warns, and some other code polishing (Jani, Lucas,
Ville)
- Selftests fixes, improvements and additions (Chris, Dan, Aditya, Matt Auld)
- Fix plane possible_crtcs bit mask (Anshuman)
- Fixes and cleanup on GLK pre production identification and w/a (Ville)
- Fix display orientation on few cases (Hans, Ville)
- dbuf clean-up and improvements for slice arrays handling (Ville)
- Improvement around min cdclk calculation (Stanislav)
- Fixes and refactor around display PLLs (Imre)
- Other execlists and perf fixes (Chris)
- Documentation fixes (Jani, Chris)
- Fix build issue (Anshuman)
- Many more fixes around the locking mechanisms (Chris)
- Other fixes and debugability info around preemption (Chris, Tvrtko)
- Add mechanism to submit a context WA on ring submission (Mika)
- Clear all Eu/L3 resitual context (Prathap)
- More changes around local memory (Abdiel, Matt, Chris)
- Fix RPS (Chris)
- DP MST fix (Lyude)
- Display FBC fixes (Jose, RK)
- debugfs cleanup (Tvrtko)
- More convertion towards drm_debive based loggin (Wambui, Ram)
- Avoid potential buffer overflow (Takashi)
- Ice Lake and Elkhart Lake workarounds (Matt Roper)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEbSBwaO7dZQkcLOKj+mJfZA7rE8oFAl5sIZ0ACgkQ+mJfZA7r
E8o1LQf+L/Vpm46QQGEyzHINf/gTQvFvumuNAX352vEHaKUgLtTuI7xfpd0c83G1
5VI+L0Q/ARvakkgfZuHYInlxc9azkcPF1wXb3bLqkoiJ15ydwx5GWjVpZ8uFT+fG
xzaHBqhqUcvw/kXI1Cy5kIDAlFO9rKLsoLS2qQF9BsYHyxa52ok9/hW+lM7C+vfR
aYvEr7aAK0o06mqgwc3DHXGuzaS1S9kxtvj9ZkHNsD9iwD4rrEIvW3BPuDqEVkGq
TkKfThhzJp2FDjXkgCQbLm2BQmxBS0aihwNsQ/lDUUAxcFiuRYwMSoT63vPD1OYI
lgG0BuJkwK7csJIMrnOs/ZAMeKyTQA==
=vrB8
-----END PGP SIGNATURE-----
Merge tag 'drm-intel-next-2020-03-13' of git://anongit.freedesktop.org/drm/drm-intel into drm-next
UAPI Changes:
On i915 we have a new UAPI to allow userspace to specify CS ring buffer size on
construction (I915_CONTEXT_PARAM_RINGSIZE) and also new sysfs entries exposing
various engine properties
GVT Changes:
VFIO edid getting expanded to all platforms and a big cleanup around attr
group, unused vblank complete, kvmgt, Intel engine and dev_priv usages.
i915 Changes:
- new UAPI to allow userspace to specify CS ring buffer size on construction
(I915_CONTEXT_PARAM_RINGSIZE) - (Chris)
- New sysfs entries exposing various engine properties (Chris)
- Tiger Lake is out of require_force_probe protection (Jose)
- Changes in many places around active requests, reset and heartbeat (Chris)
- Stop assigning drm-dev_private pointer (Jani)
- Many code refactor in many places, including intel_modeset_init,
increasing use of intel_uncore_*, vgpu, and gvt stuff (Jani)
- Fixes around display pipe iterators (Anshuman)
- Tigerlake enabling work (Matt Ropper, Matt Atwood, Ville, Lucas, Daniele,
Jose, Anusha, Vivek, Swathi, Caz. Kai)
- Code clean-up like reducing use of drm/i915_drv.h, removing unused
registers, removing garbage warns, and some other code polishing (Jani, Lucas,
Ville)
- Selftests fixes, improvements and additions (Chris, Dan, Aditya, Matt Auld)
- Fix plane possible_crtcs bit mask (Anshuman)
- Fixes and cleanup on GLK pre production identification and w/a (Ville)
- Fix display orientation on few cases (Hans, Ville)
- dbuf clean-up and improvements for slice arrays handling (Ville)
- Improvement around min cdclk calculation (Stanislav)
- Fixes and refactor around display PLLs (Imre)
- Other execlists and perf fixes (Chris)
- Documentation fixes (Jani, Chris)
- Fix build issue (Anshuman)
- Many more fixes around the locking mechanisms (Chris)
- Other fixes and debugability info around preemption (Chris, Tvrtko)
- Add mechanism to submit a context WA on ring submission (Mika)
- Clear all Eu/L3 resitual context (Prathap)
- More changes around local memory (Abdiel, Matt, Chris)
- Fix RPS (Chris)
- DP MST fix (Lyude)
- Display FBC fixes (Jose, RK)
- debugfs cleanup (Tvrtko)
- More convertion towards drm_debive based loggin (Wambui, Ram)
- Avoid potential buffer overflow (Takashi)
- Ice Lake and Elkhart Lake workarounds (Matt Roper)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200314001535.GA2969344@intel.com
This fixes a problem found on the MacBookPro 2017 Retina panel.
The panel reports 10 bpc color depth in its EDID, and the
firmware chooses link settings at boot which support enough
bandwidth for 10 bpc (324000 kbit/sec = multiplier 0xc),
but the DP_MAX_LINK_RATE dpcd register only reports
2.7 Gbps (multiplier value 0xa) as possible, in direct
contradiction of what the firmware successfully set up.
This restricts the panel to 8 bpc, not providing the full
color depth of the panel.
This patch adds a quirk specific to the MBP 2017 15" Retina
panel to add the additiional 324000 kbps link rate during
edp setup.
Link to previous discussion of a different attempted fix
with Ville and Jani:
https://patchwork.kernel.org/patch/11325935/
v2: Follow Jani's proposal of defining quirk_rates[] instead
of just appending 324000. This for better clarity.
v3: Rebased onto current drm-tip, as of 16-March-2020. Adapt
to new edid_quirks parameter of drm_dp_has_quirk().
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Tested-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200316042340.4783-1-mario.kleiner.de@gmail.com
Converts various instances of the printk based drm logging macros to the
struct drm_device based logging macros in i915/display/intel_hdcp.c.
This also involves extracting the drm_i915_private device from the
intel_connector type for use in the macros.
v2 by Jani:
- rebase
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Wambui Karuga <wambui.karugax@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/47d5e88dedc08ee48938344296ada550dedd5f90.1583766715.git.jani.nikula@intel.com
Convert various instances of printk based drm logging macros to the
struct drm_device based logging macros in i915/display/intel_fbdev.c.
This also involves extracting the drm_i915_private device from various
intel types.
v2 by Jani:
- fix the final one too
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Wambui Karuga <wambui.karugax@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/7081a49d20cc46b1b1144c83a4e21294d121d8a7.1583766715.git.jani.nikula@intel.com
Since commit 987d65d013 (drm: debugfs: make
drm_debugfs_create_files() never fail), drm_debugfs_create_files() never
fails and should return void. Therefore, remove its use as the
return value of debugfs_init() functions and have the functions return
void.
v2: convert intel_display_debugfs_register() stub to return void too.
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310133121.27913-15-wambui.karugax@gmail.com
For icl+, have hw read out to create hw blob of gamma
lut values. icl+ platforms supports multi segmented gamma
mode by default, add hw lut creation for this mode.
This will be used to validate gamma programming using dsb
(display state buffer) which is a tgl specific feature.
v2: -readout code for multisegmented gamma has to come
up with some intermediate entries that aren't preserved
in hardware (Jani N)
-linear interpolation (Ville)
-moved common code to check gamma_enable to specific funcs,
since icl doesn't support that
v3: -use u16 instead of __u16 [Jani N]
-used single lut [Jani N]
-improved and more readable for loops [Jani N]
-read values directly to actual locations and then fill gaps [Jani N]
-moved cleaning to patch 1 [Jani N]
-renamed icl_read_lut_multi_seg() to icl_read_lut_multi_segment to
make it similar to icl_load_luts()
-renamed icl_compute_interpolated_gamma_blob() to
icl_compute_interpolated_gamma_lut_values() more sensible, I guess
v4: -removed interpolated func for creating gamma lut values
-removed readouts of fine and coarse segments, failure to read PAL_PREC_DATA
correctly
v5: -added gamma_enable check inside read_luts()
v6: -renamed intel_color_lut_entry_equal() to intel_color_lut_entries_equal() [Ville]
-changed if-else to switch [Ville]
-removed intel_color_lut_entry_multi_equal() [Ville]
v7: -checkpatch warnings
v8: -rebased
v9: -rebased, aligned with Ville's style of gamma cleanup
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200317135736.14305-1-swati2.sharma@intel.com
drm_dp_mst_topology_mgr_cbs.destroy_connector callbacks are identical
amongst every driver and don't do anything other than cleaning up the
connector((drm_connector_unregister()/drm_connector_put())) except for
amdgpu_dm driver where some amdgpu_dm specific code in there.
This connector cleaning up is now being handled in the drm core so
driver destroy_connector callbacks are not needed (except for
amdgpu_dm) hence remove them.
Removal is done with below sementic patch:
@r1@
identifier func, E;
@@
struct drm_dp_mst_topology_cbs E = {
...,
- .destroy_connector = func
};
@delete depends on r1@
identifier r1.func;
@@
- static void func(...){...}
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Suggested-by: Emil Velikov <emil.velikov@collabora.com>
Suggested-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200307083023.76498-6-pankaj.laxminarayan.bharadiya@intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
drm_dp_mst_port_add_connector() directly calls the
drm_connector_register() now and
drm_dp_mst_topology_mgr_cbs.register_connector callback is not getting
called anymore.
Hence remove all drm_dp_mst_topology_mgr_cbs.register_connector
callbacks.
This is the preparatory step for removing the
drm_dp_mst_topology_mgr_cbs.register_connector callback hook.
The removal is done with below sementic patch:
@r1@
identifier func, E;
@@
struct drm_dp_mst_topology_cbs E = {
...,
- .register_connector = func
};
@delete depends on r1@
identifier r1.func;
@@
- static void func(...){...}
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Suggested-by: Emil Velikov <emil.velikov@collabora.com>
Suggested-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200307083023.76498-3-pankaj.laxminarayan.bharadiya@intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Gen12 hardware supports HDMI audio pixel clocks of 296.7/297Mhz
and 593.4/594Mhz. Add the missing rates and add logic to ignore
them if running on older hardware.
Bspec: 49333
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310162338.9387-1-kai.vehmanen@linux.intel.com
Converts various instances of the printk based drm logging macros to the
struct drm_device based logging macros in i915/display/intel_hotplug.c.
In some cases, this involves extracting the drm_i915_private pointer from
the drm_device struct to be used in the logging macros.
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/3dfda89ab4a234f299ada77abd14163cef3f8bd4.1583766715.git.jani.nikula@intel.com
