Add am335x-moxa-uc-8100-common.dtsi for many products of MOXA UC-8100
series, and remove common nodes from am335x-moxa-uc-8100-me-t.dts.
Signed-off-by: Johnson Chen <johnsonch.chen@moxa.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add information about panel orientation, so that the
system boots into a properly rotated shell.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add Droid 4 specific compatible value in addition to the
generic one, so that we have the ability to add panel
specific quirks in the future.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The standard binding for DSI requires that the channel number
of the panel is encoded in DT. This adds the channel number in
all OMAP3-5 boards in preparation for using common infrastructure.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We currently have a different clock rate for droid4 compared to the
stock v3.0.8 based Android Linux kernel:
# cat /sys/kernel/debug/clk/dpll_*_m7x2_ck/clk_rate
266666667
307200000
# cat /sys/kernel/debug/clk/l3_gfx_cm:clk:0000:0/clk_rate
307200000
Let's fix this by configuring sgx to use 153.6 MHz instead of 307.2 MHz.
Looks like also at least duover needs this change to avoid hangs, so
let's apply it for all 4430.
This helps a bit with thermal issues that seem to be related to memory
corruption when using sgx. It seems that other driver related issues
still remain though.
Cc: Arthur Demchenkov <spinal.by@gmail.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DSI was not probing due to base address off by 0x1000, and sys_clk
missing.
With this patch, the Pyra display works if HDMI is disabled in the
device tree.
Fixes: 5a507162f0 ("ARM: dts: Configure interconnect target module for omap5 dsi1")
Signed-off-by: David Shah <dave@ds0.me>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
[tony@atomide.com: standardized subject line, added fixes tag]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The chip is hardwired to the board's PCIe bus and needs to be properly
setup trough a firmware routine after a PCI fundamental reset. Pass the
reset controller phandle that takes care of triggering the
initialization to the relevant PCI device.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20200629161845.6021-5-nsaenzjulienne@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the reset driver exposing Raspberry Pi 4's firmware based USB
reset routine is available, let's add the device tree node exposing it.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20200629161845.6021-4-nsaenzjulienne@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can power off l4_abe domain when not in use when we configure it for
genpd. And with that change, we can now also drop the old unused legacy
platform data.
Note that we also need to now use "simple-pm-bus" instead of "simple-bus"
for PM runtime to get enabled for the bus.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can power off the SGX power domain when not in use when we configure
it for genpd. And with that change, we can now also drop the old unused
legacy platform data.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the devicetree properties to enable instruction and data prefetch
on exynos4210 and exynos4412 which use the L2C-310 cache. No other
Exynos chip appears to be using this L2 cache hardware.
This follows the default bits being set in the l2c_aux_val register
for the Exynos platform, which can now be cleared as a result.
Signed-off-by: Guillaume Tucker <guillaume.tucker@collabora.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Update the never-mainlined "samsung,trats2-audio" binding and instead
use the new "samsung,midas-audio" binding.
Signed-off-by: Simon Shields <simon@lineageos.org>
[s.nawrocki: fixed DAPM routing entries for MICBIAS1/2, adjusted to
new cpu/codec binding, corrected the regulator nodes indexing]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Fixes the register address for the timer3 entry on Arria10.
Fixes: 475dc86d08 ("arm: dts: socfpga: Add a base DTSI for Altera's Arria10 SOC")
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Configure the SAI device node, configure audio clock
and pinctrl.
Enable the audio sound card, which use the SAI1 and
wm8960, and enable headphone detection.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add device trees for TQMa6S, TQMa6Q, and TQMa6QP embedded modules.
The A and B SoM variants are for hardware revisions that differ in
how the I2C devices are connected. For details, see [1].
This is a combination of the patches
"arm: dt: imx6qdl: add tqma6[qdl] som on mba6 mainboard",
"arm: dt: tqma6: add spi with spi nor flash on SOM",
"arm: dt: add basic support for tqma6qp on mba6", and
"arm: dt: imx6qdl-tqma6: use generic jedec,spi-nor"
from the TQMa6x BSP, with the MBa6 specific parts removed.
[1] https://support.tq-group.com/en/arm/tqma6x/linux/ptxdist/overview
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
[bst@pengutronix.de: remove unnecessary container node in the iomuxc
node]
Signed-off-by: Bastian Krause <bst@pengutronix.de>
[p.zabel@pengutronix.de: merged patches from TQMa6x BSP REV.0114,
separated MBa6 DTs, fixed checkpatch and dtbs_check warnings,
added no-sd(io) properties to eMMC, added SPDX license identifiers
and commit message]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Disable Ethernet switch reset GPIO with ZII platforms that have it
enabled. HW switch reset results in a reset of the copper PHYs
inside of the switch. We want to avoid this reset of the copper PHYs
in the switch as this results in unnecessary broader network disruption on
a soft reboot of the application processor.
With the HW GPIO removed, the switch driver still performs a soft reset of
the switch core which has been shown to sufficiently meet our needs with
other ZII platforms that do not have the HW switch reset GPIO defined.
Signed-off-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the reset-gpio property, and enable PCIe on iMX6QP SABREAUTO board.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A previous commit removed the panel-dpi driver, which made the
SOM-LV video stop working because it relied on the DPI driver
for setting video timings. Now that the simple-panel driver is
available in omap2plus, this patch migrates the SOM-LV dev kits
to use a similar panel and remove the manual timing requirements.
A similar patch was already done and applied to the Torpedo family.
Fixes: 8bf4b16211 ("drm/omap: Remove panel-dpi driver")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Older versions of U-Boot would pinmux the whole board, but as
the bootloader got updated, it started to only pinmux the pins
it needed, and expected Linux to configure what it needed.
Unfortunately this caused an issue with the audio, because the
mcbsp2 pins were configured in the device tree but never
referenced by the driver. When U-Boot stopped muxing the audio
pins, the audio died.
This patch adds the references to the associate the pin controller
with the mcbsp2 driver which makes audio operate again.
Fixes: 5cb8b0fa55 ("ARM: dts: Move most of logicpd-som-lv-37xx-devkit.dts to logicpd-som-lv-baseboard.dtsi")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Older versions of U-Boot would pinmux the whole board, but as
the bootloader got updated, it started to only pinmux the pins
it needed, and expected Linux to configure what it needed.
Unfortunately this caused an issue with the audio, because the
mcbsp2 pins were configured in the device tree, they were never
referenced by the driver. When U-Boot stopped muxing the audio
pins, the audio died.
This patch adds the references to the associate the pin controller
with the mcbsp2 driver which makes audio operate again.
Fixes: 739f85bba5 ("ARM: dts: Move most of logicpd-torpedo-37xx-devkit to logicpd-torpedo-baseboard")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
rng DT node was added without a compatible string.
i.MX driver for RNGC (drivers/char/hw_random/imx-rngc.c) also claims
support for RNGB, and is currently used for i.MX25.
Let's use this driver also for RNGB block in i.MX6SL.
Fixes: e29fe21cff ("ARM: dts: add device tree source for imx6sl SoC")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add a device node for the PCIe controller on the Renesas
RZ/G1H (r8a7742) SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Link: https://lore.kernel.org/r/20200810174156.30880-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add a Display Unit (DU) node to r8a7742 SoC DT.
Boards that want to enable the DU need to specify the output topology.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200807174954.14448-6-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Some r8a7745-iwg22d-sodimm.dts device nodes are not sorted alphabetically.
This patch fixes the sorting of nodes and also fixes a typo in the stmpe
node.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20200805142634.12252-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
kernel series:
Core changes:
- The GPIO patch "gpiolib: Introduce
for_each_requested_gpio_in_range() macro" was put in an
immutable branch and merged into the pinctrl tree as well.
We see these changes also here.
- Improved debug output for pins used as GPIO.
New drivers:
- Ocelot Sparx5 SoC driver.
- Intel Emmitsburg SoC subdriver.
- Intel Tiger Lake-H SoC subdriver.
- Qualcomm PM660 SoC subdriver.
- Renesas SH-PFC R8A774E1 subdriver.
Driver improvements:
- Linear improvement and cleanups of the Intel drivers for
Cherryview, Lynxpoint, Baytrail etc. Improved locking among
other things.
- Renesas SH-PFC has added support for RPC pins, groups, and
functions to r8a77970 and r8a77980.
- The newere Freescale (now NXP) i.MX8 pin controllers have
been modularized. This is driven by the Google Android
GKI initiative I think.
- Open drain support for pins on the Qualcomm IPQ4019.
- The Ingenic driver can handle both edges IRQ detection.
- A big slew of documentation fixes all over the place.
- A few irqchip template conversions by yours truly.
-----BEGIN PGP SIGNATURE-----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=mJgb
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of the pin control changes for the v5.9 kernel
series:
Core changes:
- The GPIO patch "gpiolib: Introduce for_each_requested_gpio_in_range()
macro" was put in an immutable branch and merged into the pinctrl
tree as well. We see these changes also here.
- Improved debug output for pins used as GPIO.
New drivers:
- Ocelot Sparx5 SoC driver.
- Intel Emmitsburg SoC subdriver.
- Intel Tiger Lake-H SoC subdriver.
- Qualcomm PM660 SoC subdriver.
- Renesas SH-PFC R8A774E1 subdriver.
Driver improvements:
- Linear improvement and cleanups of the Intel drivers for
Cherryview, Lynxpoint, Baytrail etc. Improved locking among other
things.
- Renesas SH-PFC has added support for RPC pins, groups, and
functions to r8a77970 and r8a77980.
- The newere Freescale (now NXP) i.MX8 pin controllers have been
modularized. This is driven by the Google Android GKI initiative I
think.
- Open drain support for pins on the Qualcomm IPQ4019.
- The Ingenic driver can handle both edges IRQ detection.
- A big slew of documentation fixes all over the place.
- A few irqchip template conversions by yours truly.
* tag 'pinctrl-v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (107 commits)
dt-bindings: pinctrl: add bindings for MediaTek MT6779 SoC
pinctrl: stmfx: Use irqchip template
pinctrl: amd: Use irqchip template
pinctrl: mediatek: fix build for tristate changes
pinctrl: samsung: Use bank name as irqchip name
pinctrl: core: print gpio in pins debugfs file
pinctrl: mediatek: add mt6779 eint support
pinctrl: mediatek: add pinctrl support for MT6779 SoC
pinctrl: mediatek: avoid virtual gpio trying to set reg
pinctrl: mediatek: update pinmux definitions for mt6779
pinctrl: stm32: use the hwspin_lock_timeout_in_atomic() API
pinctrl: mcp23s08: Use irqchip template
pinctrl: sx150x: Use irqchip template
dt-bindings: ingenic,pinctrl: Support pinmux/pinconf nodes
pinctrl: intel: Add Intel Emmitsburg pin controller support
pinctl: ti: iodelay: Replace HTTP links with HTTPS ones
Revert "gpio: omap: handle pin config bias flags"
pinctrl: single: Use fallthrough pseudo-keyword
pinctrl: qcom: spmi-gpio: Use fallthrough pseudo-keyword
pinctrl: baytrail: Use fallthrough pseudo-keyword
...
This became wide and scattered updates all over the sound tree as
diffstat shows: lots of (still ongoing) refactoring works in ASoC,
fixes and cleanups caught by static analysis, inclusive term
conversions as well as lots of new drivers. Below are highlights:
ASoC core:
* API cleanups and conversions to the unified mute_stream() call
* Simplify I/O helper functions
* Use helper macros to retrieve RTD from substreams
ASoC drivers:
* Lots of fixes and cleanups in Intel ASoC drivers
* Lots of new stuff: Freescale MQS and i.MX6sx, Intel KeemBay I2S,
Maxim MAX98360A and MAX98373 SoundWire, various Mediatek boards,
nVidia Tegra 186 and 210, RealTek RL6231, Samsung Midas and Aries
boards, TI J721e EVM
ALSA core:
* Minor code refacotring for SG-buffer handling
HD-audio:
* Generalization of mute-LED handling with LED classdev
* Intel silent stream support for HDMI
* Device-specific fixes: CA0132, Loongson-3
Others:
* Usual USB- and HD-audio quirks for various devices
* Fixes for echoaudio DMA position handling
* Various documents and trivial fixes for sparse warnings
* Conversion to adapt inclusive terms
-----BEGIN PGP SIGNATURE-----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=sy7n
-----END PGP SIGNATURE-----
Merge tag 'sound-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This became wide and scattered updates all over the sound tree as
diffstat shows: lots of (still ongoing) refactoring works in ASoC,
fixes and cleanups caught by static analysis, inclusive term
conversions as well as lots of new drivers. Below are highlights:
ASoC core:
- API cleanups and conversions to the unified mute_stream() call
- Simplify I/O helper functions
- Use helper macros to retrieve RTD from substreams
ASoC drivers:
- Lots of fixes and cleanups in Intel ASoC drivers
- Lots of new stuff: Freescale MQS and i.MX6sx, Intel KeemBay I2S,
Maxim MAX98360A and MAX98373 SoundWire, various Mediatek boards,
nVidia Tegra 186 and 210, RealTek RL6231, Samsung Midas and Aries
boards, TI J721e EVM
ALSA core:
- Minor code refacotring for SG-buffer handling
HD-audio:
- Generalization of mute-LED handling with LED classdev
- Intel silent stream support for HDMI
- Device-specific fixes: CA0132, Loongson-3
Others:
- Usual USB- and HD-audio quirks for various devices
- Fixes for echoaudio DMA position handling
- Various documents and trivial fixes for sparse warnings
- Conversion to adopt inclusive terms"
* tag 'sound-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (479 commits)
ALSA: pci: delete repeated words in comments
ALSA: isa: delete repeated words in comments
ALSA: hda/tegra: Add 100us dma stop delay
ALSA: hda: Add dma stop delay variable
ASoC: hda/tegra: Set buffer alignment to 128 bytes
ALSA: seq: oss: Serialize ioctls
ALSA: hda/hdmi: Add quirk to force connectivity
ALSA: usb-audio: add startech usb audio dock name
ALSA: usb-audio: Add support for Lenovo ThinkStation P620
Revert "ALSA: hda: call runtime_allow() for all hda controllers"
ALSA: hda/ca0132 - Fix AE-5 microphone selection commands.
ALSA: hda/ca0132 - Add new quirk ID for Recon3D.
ALSA: hda/ca0132 - Fix ZxR Headphone gain control get value.
ALSA: hda/realtek: Add alc269/alc662 pin-tables for Loongson-3 laptops
ALSA: docs: fix typo
ALSA: doc: use correct config variable name
ASoC: core: Two step component registration
ASoC: core: Simplify snd_soc_component_initialize declaration
ASoC: core: Relocate and expose snd_soc_component_initialize
ASoC: sh: Replace 'select' DMADEVICES 'with depends on'
...
- Prevent unnecessary timer softirq invocations by extending the tracking
of the next expiring timer in the timer wheel beyond the existing NOHZ
functionality. The tracking overhead at enqueue time is within the
noise, but on sensitive workloads the avoidance of the soft interrupt
invocation is a measurable improvement.
- The obligatory new clocksource driver for Ingenic X100 OST
- The usual fixes, improvements, cleanups and extensions for newer chip
variants all over the driver space.
-----BEGIN PGP SIGNATURE-----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=uJnp
-----END PGP SIGNATURE-----
Merge tag 'timers-core-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"Time, timers and related driver updates:
- Prevent unnecessary timer softirq invocations by extending the
tracking of the next expiring timer in the timer wheel beyond the
existing NOHZ functionality.
The tracking overhead at enqueue time is within the noise, but on
sensitive workloads the avoidance of the soft interrupt invocation
is a measurable improvement.
- The obligatory new clocksource driver for Ingenic X100 OST
- The usual fixes, improvements, cleanups and extensions for newer
chip variants all over the driver space"
* tag 'timers-core-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (28 commits)
timers: Recalculate next timer interrupt only when necessary
clocksource/drivers/ingenic: Add support for the Ingenic X1000 OST.
dt-bindings: timer: Add Ingenic X1000 OST bindings.
clocksource/drivers: Replace HTTP links with HTTPS ones
clocksource/drivers/nomadik-mtu: Handle 32kHz clock
clocksource/drivers/sh_cmt: Use "kHz" for kilohertz
clocksource/drivers/imx: Add support for i.MX TPM driver with ARM64
clocksource/drivers/ingenic: Add high resolution timer support for SMP/SMT.
timers: Lower base clock forwarding threshold
timers: Remove must_forward_clk
timers: Spare timer softirq until next expiry
timers: Expand clk forward logic beyond nohz
timers: Reuse next expiry cache after nohz exit
timers: Always keep track of next expiry
timers: Optimize _next_timer_interrupt() level iteration
timers: Add comments about calc_index() ceiling work
timers: Move trigger_dyntick_cpu() to enqueue_timer()
timers: Use only bucket expiry for base->next_expiry value
timers: Preserve higher bits of expiration on index calculation
clocksource/drivers/timer-atmel-tcb: Add sama5d2 support
...
There are three SoC families newly dded to the 32-bit and
64-bit Arm architecture code in the kernel this time:
- Daniel Palmer adds initial support for two chips made by MStar, a
taiwanese SoC manufacturer that became part of Mediatek in 2012. For
now, the added support is fairly minimal, with just two of its
Cortex-A7 based 32-bit camera chips getting support for a limited
set of on-chip peripherals.
- Lars Povlsen from Microchip adds support for their new Sparx5
family of ethernet switch chips using 64-bit Cortex-A53 cores.
These are descended from earlier VSC7xxx SparX and Ocelot chips
using 32-bit MIPS cores.
- Daniele Alessandrelli from Intel adds support for the new Keem Bay
SoC for computer vision, built around a Movidius VPU with Linux
running on Arm Cortex-A53 cores.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAl8j31MACgkQmmx57+YA
GNnS7Q//achCOtBeIblV8Fyfp/lTYNpT9hFTQ5cGaoyjl9Lm1rcVCISCEGqIEJAV
FRQBz3YcQWA9pIWIf79oh6QphcoW/wUTCE+cjnHP+EOkqvw9aGFBm4nOUt4Gz92a
+gGs9HqcrxB+3ysQEDGugwRrE6htrOoCnWyurh5zZNvAEry+MV6LBwfxSUrLKy8b
iwnwl/KvWI47mWAj5nJ7fbXAgxRjFdEz+mvNBjqKhJ/OELsnWRXcxmJxF651DEb6
e/ydD7OtrWI1+81/yQxS7SeDlatFHE0JvP4WZHBGm6TB7Z3pdqIZI598UN0lVvbR
jvtljiAa2UA7h6NjscD6ECWktrF8LO8i/8ref7Fr3za/FKiLTYP2BQymnlk5nLAj
RuCvR8oriqBbseZlkGrs4afjpfwurUKNhhjVse/M3ORYYK++Bra6GZWL4gnlA2wB
GbFZ6MAw2bnbKrO6rRTu+F1NFq5/l71LP1r3Li3xbyfZ7I/XJ5aiE6knQ+vtk6Np
pfvCYSILOSnulYZvdaL/W4HV98mzjHSE4eUegGDTMKNv2dVNRGI3Mnnur7+kSXLu
550qg+GXv8JkQlkFkT2BsuaiPULOUKHFtK42fo2XhQL/zoaFlBU7HehtSBdtcKPy
XIlEEk32q+QyABKav2QJnGJMcWzfq2SSmsUliVU72zD38dG/0Fw=
=Yy3D
-----END PGP SIGNATURE-----
Merge tag 'arm-newsoc-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull new ARM SoC support from Arnd Bergmann:
"There are three SoC families newly dded to the 32-bit and 64-bit Arm
architecture code in the kernel this time:
- Daniel Palmer adds initial support for two chips made by MStar, a
taiwanese SoC manufacturer that became part of Mediatek in 2012.
For now, the added support is fairly minimal, with just two of its
Cortex-A7 based 32-bit camera chips getting support for a limited
set of on-chip peripherals.
- Lars Povlsen from Microchip adds support for their new Sparx5
family of ethernet switch chips using 64-bit Cortex-A53 cores.
These are descended from earlier VSC7xxx SparX and Ocelot chips
using 32-bit MIPS cores.
- Daniele Alessandrelli from Intel adds support for the new Keem Bay
SoC for computer vision, built around a Movidius VPU with Linux
running on Arm Cortex-A53 cores"
* tag 'arm-newsoc-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (38 commits)
ARM: mstar: Correct the compatible string for pmsleep
dt-bindings: arm: mstar: remove the binding description for mstar,pmsleep
dt-bindings: mfd: syscon: add compatible string for mstar,msc313-pmsleep
ARM: mstar: Add reboot support
ARM: mstar: Add "pmsleep" node to base dtsi
ARM: mstar: Add PMU
ARM: mstar: Adjust IMI size for infinity3
ARM: mstar: Adjust IMI size for mercury5
ARM: mstar: Adjust IMI size of infinity
ARM: mstar: Add IMI SRAM region
dt-bindings: arm: mstar: Move existing MStar binding descriptions
dt-bindings: arm: mstar: Add binding details for mstar, pmsleep
ARM: mstar: Fix dts filename for 70mai midrive d08
ARM: mstar: Add dts for 70mai midrive d08
ARM: mstar: Add dts for msc313(e) based BreadBee boards
ARM: mstar: Add mercury5 series dtsis
ARM: mstar: Add infinity/infinity3 family dtsis
ARM: mstar: Add Armv7 base dtsi
ARM: mstar: Add binding details for mstar,l3bridge
ARM: mstar: Add machine for MStar/Sigmastar Armv7 SoCs
...
These are mostly cosmetic changes and minor bugfixes for the SoC
specific code, across the 32-bit at91, mvebu, davinci, samsung, and
omap platforms.
The main notable changes are for the Samsung Exynos platform, which
sees a rewrite of gpio handling and a change to restore and adds
a workaround for a problem with cpuidle support.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=IHpg
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Arnd Bergmann:
"These are mostly cosmetic changes and minor bugfixes for the SoC
specific code, across the 32-bit at91, mvebu, davinci, samsung, and
omap platforms.
The main notable changes are for the Samsung Exynos platform, which
sees a rewrite of gpio handling and a change to restore and adds a
workaround for a problem with cpuidle support"
* tag 'arm-soc-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: socfpga: PM: add missing put_device() call in socfpga_setup_ocram_self_refresh()
MAINTAINERS: arm/amlogic: add designated reviewers
ARM: davinci: dm646x-evm: Simplify error handling in 'evm_sw_setup()'
ARM: davinci: Fix trivial spelling
ARM: davinci: Replace HTTP links with HTTPS ones
ARM: s3c24xx: Replace HTTP links with HTTPS ones
ARM: orion/gpio: Make use of for_each_requested_gpio()
ARM: at91: Replace HTTP links with HTTPS ones
ARM: at91: pm: add missing put_device() call in at91_pm_sram_init()
ARM: rpc: Change blacklist to quirklist in ecode.c file
ARM: OMAP: Replace HTTP links with HTTPS ones
ARM: s3c24xx: leds: Convert to use GPIO descriptors
udc: lpc32xx: mark local function static
ARM: exynos: MCPM: Restore big.LITTLE cpuidle support
ARM: exynos: clear L310_AUX_CTRL_FULL_LINE_ZERO in default l2c_aux_val
As usual, there are many patches addressing minor issues in existing
DTS files, such as DTC warnings, or adding support for additional
peripherals.
There are three added SoCs in existing product families:
- Amazon:
Alpine v3 is a 16-core Cortex-A72 SoC from Amazon's Annapurna Labs,
otherwise known as AL73400 or first-generation Graviton, and following
the already supported Cortex-A1`5 and Cortex-A57 based Alpine chips.
This one is added together with the official Evaluation platform.
- Qualcomm:
The Snapdragon SDM630 platform is a family of mid-range mobile phone
chips from 2017 based on Cortex-A53 or Kryo 260 CPUs.
A total of five end-user products are added based on these, all
Android phones from Sony: Xperia 10, 10 Plus, XA2, XA2 Plus and
XA2 Ultra.
- Renesas:
RZ/G2H (r8a774e1) is currently the top model in the Renesas RZ/G
family, and apparently closely related to the RZ/G2N and RZ/G2M
models we already support but has a faster GPU and additional
on-chip peripherals.
It is added along with the HopeRun HiHope RZ/G2H development board
A small number of new boards for already supported SoCs also debut:
- Allwinner sunxi:
Only one new machine, revision v1.2 of the Pine64 PinePhone
(non-Android) smartphone, containing minor changes compared to
earlier versions.
- Amlogic Meson:
WeTek Core2 is an Amlogic S912 (GXM) based Set-top-box
- Aspeed:
EthanolX is AMD's EPYC data center rerence platform, using an
ASpeed AST2600 baseboard management controller.
- Mediatek:
Lenovo IdeaPad Duet 10.1" (kukui/krane) is a new Chromebook
based on the MT8183 (Helio P60t) SoC.
- Nvidia Tegra:
ASUS Google Nexus 7 and Acer Iconia Tab A500 are two Android
tablets from around 2012 using Tegra 3 and Tegra 2, respectively.
Thanks to PostmarketOS, these can now run mainline kernels
and become useful again.
The Jetson Xavier NX Developer Kit uses a SoM and carrier board
for the Tegra194, their latest 64-bit chip based on Carmel CPU
cores and Volta graphics.
- NXP i.MX:
Five new boards based on the 32-bit i.MX6 series are added:
The MYiR MYS-6ULX single-board computer, and four different
models of industrial computers from Protonic.
- Qualcomm:
MikroTik RouterBoard 3011 is a rackmounted router based on the
32-bit IPQ8064 networking SoC
Three older phones get added, the Snapdragon 808 (msm8992) based
Xiaomi Libra (Mi 4C) and Microsoft Lumia 950, originally running
Windows Phone, and the Snapdragon 810 (msm8994) based Sony
Xperia Z5.
- Renesas:
In addition to the HiHope RZ/G2H board mentioned above, we gain
support for board versions 3.0 and 4.0 of the earlier RZ/G2M and
RZ/G2N reference boards.
Beacon EmbeddedWorks adds another SoM+Carrier development board
for RZ/G2M.
- Rockchips:
Radxa Rock Pi N8 development board and the VMARC RK3288 SoM it
is based on, using the high-end 32-bit rk3288 SoC.
Notable updates to existing platforms are usually for added on-chip
peripherals, including:
- ASpeed AST2xxx (various)
- Allwinner (cpufreq, thermal, Pinephone touchscreen)
- Amlogic Meson (audio, gpu dvdfs, board updates)
- Arm Versatile
- Broadcom (board updates for switch ports, Raspberry pi clock updates)
- Hisilicon (various)
- Intel/Altera SoCFPGA (various)
- Marvell Armada 7xxx/8xxx (smmu)
- Marvell MMP (GPU on mmp2/mmp3)
- Mediatek mt8183 (USB, pericfg)
- NXP Layerscape (VPU, thermal, DSPI)
- NXP i.MX (VPU, bindings, board updates)
- Nvidia Tegra194 (GPU)
- Qualcomm (GPU, Interconnect, ...)
- Renesas R-Car (SPI, IPMMU, board updates)
- STMicroelectronics STM32 (various)
- Samsung Exynos (various)
- Socionext Uniphier (updates to serial, and pcie)
- TI K3 (serdes, usb3, audio, sd, chipid)
- TI OMAP (IPU/DSP remoteproc changes, dropping platform data)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=Tpj3
-----END PGP SIGNATURE-----
Merge tag 'arm-dt-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC DT updates from Arnd Bergmann:
"As usual, there are many patches addressing minor issues in existing
DTS files, such as DTC warnings, or adding support for additional
peripherals.
There are three added SoCs in existing product families:
- Amazon:
Alpine v3 is a 16-core Cortex-A72 SoC from Amazon's Annapurna Labs,
otherwise known as AL73400 or first-generation Graviton, and
following the already supported Cortex-A1`5 and Cortex-A57 based
Alpine chips. This one is added together with the official
Evaluation platform.
- Qualcomm:
The Snapdragon SDM630 platform is a family of mid-range mobile
phone chips from 2017 based on Cortex-A53 or Kryo 260 CPUs. A total
of five end-user products are added based on these, all Android
phones from Sony: Xperia 10, 10 Plus, XA2, XA2 Plus and XA2 Ultra.
- Renesas:
RZ/G2H (r8a774e1) is currently the top model in the Renesas RZ/G
family, and apparently closely related to the RZ/G2N and RZ/G2M
models we already support but has a faster GPU and additional
on-chip peripherals. It is added along with the HopeRun HiHope
RZ/G2H development board
A small number of new boards for already supported SoCs also debut:
- Allwinner sunxi:
Only one new machine, revision v1.2 of the Pine64 PinePhone
(non-Android) smartphone, containing minor changes compared to
earlier versions.
- Amlogic Meson:
WeTek Core2 is an Amlogic S912 (GXM) based Set-top-box
- Aspeed:
EthanolX is AMD's EPYC data center rerence platform, using an
ASpeed AST2600 baseboard management controller.
- Mediatek:
Lenovo IdeaPad Duet 10.1" (kukui/krane) is a new Chromebook based
on the MT8183 (Helio P60t) SoC.
- Nvidia Tegra:
ASUS Google Nexus 7 and Acer Iconia Tab A500 are two Android
tablets from around 2012 using Tegra 3 and Tegra 2, respectively.
Thanks to PostmarketOS, these can now run mainline kernels and
become useful again.
The Jetson Xavier NX Developer Kit uses a SoM and carrier board for
the Tegra194, their latest 64-bit chip based on Carmel CPU cores
and Volta graphics.
- NXP i.MX:
Five new boards based on the 32-bit i.MX6 series are added: The
MYiR MYS-6ULX single-board computer, and four different models of
industrial computers from Protonic.
- Qualcomm:
MikroTik RouterBoard 3011 is a rackmounted router based on the
32-bit IPQ8064 networking SoC
Three older phones get added, the Snapdragon 808 (msm8992) based
Xiaomi Libra (Mi 4C) and Microsoft Lumia 950, originally running
Windows Phone, and the Snapdragon 810 (msm8994) based Sony Xperia
Z5.
- Renesas:
In addition to the HiHope RZ/G2H board mentioned above, we gain
support for board versions 3.0 and 4.0 of the earlier RZ/G2M and
RZ/G2N reference boards. Beacon EmbeddedWorks adds another
SoM+Carrier development board for RZ/G2M.
- Rockchips:
Radxa Rock Pi N8 development board and the VMARC RK3288 SoM it is
based on, using the high-end 32-bit rk3288 SoC.
Notable updates to existing platforms are usually for added on-chip
peripherals, including:
- ASpeed AST2xxx (various)
- Allwinner (cpufreq, thermal, Pinephone touchscreen)
- Amlogic Meson (audio, gpu dvdfs, board updates)
- Arm Versatile
- Broadcom (board updates for switch ports, Raspberry pi clock updates)
- Hisilicon (various)
- Intel/Altera SoCFPGA (various)
- Marvell Armada 7xxx/8xxx (smmu)
- Marvell MMP (GPU on mmp2/mmp3)
- Mediatek mt8183 (USB, pericfg)
- NXP Layerscape (VPU, thermal, DSPI)
- NXP i.MX (VPU, bindings, board updates)
- Nvidia Tegra194 (GPU)
- Qualcomm (GPU, Interconnect, ...)
- Renesas R-Car (SPI, IPMMU, board updates)
- STMicroelectronics STM32 (various)
- Samsung Exynos (various)
- Socionext Uniphier (updates to serial, and pcie)
- TI K3 (serdes, usb3, audio, sd, chipid)
- TI OMAP (IPU/DSP remoteproc changes, dropping platform data)"
* tag 'arm-dt-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (605 commits)
arm64: dts: meson: odroid-n2: add jack audio output support
arm64: dts: meson: odroid-n2: enable audio loopback
ARM: dts: berlin: Align L2 cache-controller nodename with dtschema
arm64: dts: qcom: Add Microsoft Lumia 950 (Talkman) device tree
arm64: dts: qcom: Add Xiaomi Libra (Mi 4C) device tree
arm64: dts: qcom: msm8992: Add RPMCC node
arm64: dts: qcom: msm8992: Add PSCI support.
arm64: dts: qcom: msm8992: Add PMU node
arm64: dts: qcom: msm8992: Add BLSP2_UART2 and I2C nodes
arm64: dts: qcom: msm8992: Add SPMI PMIC arbiter device
arm64: dts: qcom: msm8992: Add a SCM node
arm64: dts: qcom: msm8992: Add a proper CPU map
arm64: dts: qcom: bullhead: Move UART pinctrl to SoC
arm64: dts: qcom: bullhead: Add qcom,msm-id
arm64: dts: qcom: msm8992: Fix SDHCI1
arm64: dts: qcom: msm8992: Modernize the DTS style
arm64: dts: qcom: Add support for Sony Xperia Z5 (SoMC Sumire-RoW)
arm64: dts: qcom: Move msm8994-smd-rpm contents to lg-bullhead.
arm64: dts: qcom: msm8994: Add support for SMD RPM
arm64: dts: qcom: msm8992: Add a label to rpm-requests
...
The compatible string for the pmsleep region has changed.
Update the MStar/Sigmastar v7 base dtsi with the new string.
Link: https://lore.kernel.org/r/20200729150748.1945589-4-daniel@0x0f.com
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
These are the latest device tree fixes for Arm SoCs:
- TI Keystone2 ethernet regressed after a driver change broke with
incorrect phy-mode in a board's DT source.
- A similar fix is needed for two i.MX boards that were missed in
an earlier bugfix.
- DT change for Armada 38x allowing to add the register needed to fix
NETA lockup when repeatedly switching speed.
- One fix on imx6qdl-icore pin muxing to get USB OTG_ID and SD card
detect work correctly.
- Two fixes for the Allwinner SoCs, one to relax the CMA allocation
ranges that were failing on older SoCs and one to fix Cedrus on the H6.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=qXc9
-----END PGP SIGNATURE-----
Merge tag 'arm-fixes-5.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc into master
Pull ARM SoC DT fixes from Arnd Bergmann:
"These are the latest device tree fixes for Arm SoCs:
- TI Keystone2 ethernet regressed after a driver change broke with
incorrect phy-mode in a board's DT source.
- A similar fix is needed for two i.MX boards that were missed in an
earlier bugfix.
- DT change for Armada 38x allowing to add the register needed to fix
NETA lockup when repeatedly switching speed.
- One fix on imx6qdl-icore pin muxing to get USB OTG_ID and SD card
detect work correctly.
- Two fixes for the Allwinner SoCs, one to relax the CMA allocation
ranges that were failing on older SoCs and one to fix Cedrus on the
H6"
* tag 'arm-fixes-5.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: dts: keystone-k2g-evm: fix rgmii phy-mode for ksz9031 phy
ARM: dts: armada-38x: fix NETA lockup when repeatedly switching speeds
ARM: dts: imx6qdl-icore: Fix OTG_ID pin and sdcard detect
ARM: dts: imx6sx-sabreauto: Fix the phy-mode on fec2
ARM: dts: imx6sx-sdb: Fix the phy-mode on fec2
arm64: dts: allwinner: h6: Fix Cedrus IOMMU usage
ARM: dts sunxi: Relax a bit the CMA pool allocation range
MStar v7 SoCs support reset by writing a magic value to a register
in the "pmsleep" area.
This adds a node for using the syscon reboot driver to trigger a reset.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds a node for the pmsleep area so that other
drivers can access registers contained within it.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
mercury5 family chips have 128KB of SRAM in the IMI region.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
All MStar v7 SoCs have an internal SRAM region that is between 64KB
(infinity2m) and 128KB(infinity3, mercury5).
The region is always at the same base address and is used for the
second stage loader (MStar IPL or u-boot SPL) and will be used for
the DDR self-refresh entry code within the kernel eventually.
This patch adds a 128KB region to the SoC and the minimum 64KB SRAM
region to the base dtsi. Families with more SRAM will override the
size in their family level dtsi.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Adds initial support for the 70mai midrive d08 dash camera.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
BreadBee is an opensource development board based on the
MStar msc313(e) SoC.
Hardware details, schematics and so on can be found at:
https://github.com/breadbee/breadbee
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This adds a family level dtsi for the mercury5 and then a
chip level dtsi for the ssc8336n chip.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This adds two family level dtsis for the infinity and infinity3
and then adds a chip level dtsi each for a chip in those families.
infinity3.dtsi includes infinity.dtsi as these SoCs share most of
their memory map and we would have a lot of duplication otherwise.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Adds initial dtsi for the base MStar/Sigmastar Armv7 SoCs.
These SoCs have very similar memory maps and this will avoid
duplicating nodes across multiple dtsis.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Enable the second EHCI controller on the AST2600. Also add a line-name
for the GPIO that controls power to the USB port.
The power control is in place to allow the port to be disabled, for
those that are worried about rogue USB sticks.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Enable the second EHCI controller on the AST2600. Also add a line-name
for the GPIO that controls power to the USB port.
The power control is in place to allow the port to be disabled, for
those that are worried about rogue USB sticks.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Rainier uses the P10 processor so the OCC binding should reflect that.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add the four SPI masters on each CFAM. Each master has four 128KB EEPROM
devices attached to it.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Adding pca9552 exposes the presence detect lines for the cards and
tca9554 exposes the presence details for the cards.
Signed-off-by: Jet Li <Jet.Li@ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Initial introduction of AMD EthanolX platform equipped with an
Aspeed ast2500 BMC manufactured by AMD.
AMD EthanolX platform is an AMD customer reference board with an
Aspeed ast2500 BMC manufactured by AMD.
This adds AMD EthanolX device tree file including the flash layout
used by EthanolX BMC machines.
Signed-off-by: Supreeth Venkatesh <supreeth.venkatesh@amd.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
We have a 4-bus mux whose output is selected by two GPIO inputs. Wire it
up in the devicetree and ensure the output is enabled by hogging the
appropriate line.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Since commit bcf3440c6d ("net: phy: micrel: add phy-mode support for the
KSZ9031 PHY") the networking is broken on keystone-k2g-evm board.
The above board have phy-mode = "rgmii-id" and it is worked before because
KSZ9031 PHY started with default RGMII internal delays configuration (TX
off, RX on 1.2 ns) and MAC provided TX delay by default.
After above commit, the KSZ9031 PHY starts handling phy mode properly and
enables both RX and TX delays, as result networking is become broken.
Fix it by switching to phy-mode = "rgmii-rxid" to reflect previous
behavior.
Fixes: bcf3440c6d ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- new board: WeTek Core2
- audio playback support on more boards
- add GPU DVFS
-----BEGIN PGP SIGNATURE-----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=ibOR
-----END PGP SIGNATURE-----
Merge tag 'amlogic-dt64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/dt
arm64: dts: amlogic: updates for v5.9 (round 2)
- new board: WeTek Core2
- audio playback support on more boards
- add GPU DVFS
* tag 'amlogic-dt64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
arm64: dts: amlogic: meson-g12: add the Mali OPP table and use DVFS
arm64: dts: amlogic: meson-gxm: add the Mali OPP table and use DVFS
arm64: dts: amlogic: meson-gx: add the Mali-450 OPP table and use DVFS
arm64: dts: meson: add support for the WeTek Core 2
dt-bindings: arm: amlogic: add support for the WeTek Core 2
arm64: dts: meson: add audio playback to khadas-vim3l
arm64: dts: meson: add audio playback to odroid-c4
arm64: dts: meson: update spifc node name on Khadas VIM3/VIM3L
ARM: dts: meson: Align L2 cache-controller nodename with dtschema
arm64: dts: meson-gxl-s805x: reduce initial Mali450 core frequency
arm64: dts: meson: add missing gxl rng clock
soc: amlogic: meson-gx-socinfo: Fix S905X3 and S905D3 ID's
Link: https://lore.kernel.org/r/7h8sf8671u.fsf@baylibre.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- DT change for Armada 38x allowing to add the register needed to fix
NETA lockup when repeatedly switching speed.
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCXxqaPwAKCRALBhiOFHI7
1YANAKCEUNj0n91jslQNBACKuB7a79Ag3ACbB/hWOsGi+BVNlDy5mnXeoT5ZEd0=
=GJyb
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu into arm/fixes
mvebu fixes for 5.8 (part 1)
- DT change for Armada 38x allowing to add the register needed to fix
NETA lockup when repeatedly switching speed.
* tag 'mvebu-fixes-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
ARM: dts: armada-38x: fix NETA lockup when repeatedly switching speeds
- Fix the reg-init PHY for the dlink-dns327l (Armada 370)
- Replace HTTP links with HTTPS one in device tree of the Excito
Bubba B3 (Kirkwood)
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCXxqh0gAKCRALBhiOFHI7
1R9KAJ0TuEHE0boReOUAhpAlfYIqYeR5QQCfUuD/p2aoTSfNNyctLQsHmnjBYao=
=PzgE
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu into arm/dt
mvebu dt for 5.9 (part 1)
- Fix the reg-init PHY for the dlink-dns327l (Armada 370)
- Replace HTTP links with HTTPS one in device tree of the Excito
Bubba B3 (Kirkwood)
* tag 'mvebu-dt-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
ARM: dts: dlink-dns327l: fix reg-init PHY
ARM: dts: kirkwood: Replace HTTP links with HTTPS ones
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
To support the change in "phy: armada-38x: fix NETA lockup when
repeatedly switching speeds" we need to update the DT with the
additional register.
Fixes: 14dc100b44 ("phy: armada38x: add common phy support")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Enable pwm_tacho device for fan control and monitoring in Wedge40.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Enable ADC controller and corresponding voltage sensoring channels for
Wedge40.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Disable i2c bus #9, #10 and #13 as these i2c controllers are not used on
Wedge40.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Create all the i2c switches in device tree and use aliases to assign
child channels with consistent bus numbers.
Besides, "i2c-mux-idle-disconnect" is set for all the i2c switches to
avoid potential conflicts when multiple devices (beind the switches)
use the same device address.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The GPIO on Q0 is used for resetting the CFAM of the processor that the
ASPEED master is connected to.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The GPIO on Q0 is used for resetting the CFAM of the processor that the
ASPEED master is connected to.
The signal is wired as active high on the first pass systems.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
- Add the high resolution support for SMP/SMT on the Ingenic timer (Zhou Yanjie)
- Add support for i.MX TPM driver with ARM64 (Anson Huang)
- Fix typo by replacing KHz to kHz (Geert Uytterhoeven)
- Add 32kHz support by setting the minimum ticks to 5 on Nomadik MTU (Linus Walleij)
- Replace HTTP links with HTTPS ones for security reasons (Alexander A. Klimov)
- Add support for the Ingenic X1000 OST (Zhou Yanjie)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAl8ZqeUACgkQqDIjiipP
6E9tawf/UGUhEfB+VmH9w60NJlM0fC5a/TjVOb4yMjTZjjdyd4zMBHemF+dqMNnw
wTr+S8U9QfvP4BDgg1hWV+vhAwxz2xkhR0cGtOQjck5322vZglGSmAVqTCAlQMoZ
LNm98XeUYYVNMB+/+BHkf8F/nHV9vRo8sJg7UnvX/6RCykXFYXVP+P8LfkAU1MPt
8vaRPCcyGnYXrgjDYY5M5qYudLNpFPrzr1yJDWdwWUliwH3T1X1FNogTdUo955qk
wM+Hb4yPRuRufM+yATPsRedQypZFpoWFObuEMD2FaIw/LZVxV7D1tmw5KhL2V1tZ
XSzNiJDEgri/4LaVzXKP7sVlQlZfDQ==
=DXTp
-----END PGP SIGNATURE-----
Merge tag 'timers-v5.9' of https://git.linaro.org/people/daniel.lezcano/linux into timers/core
Pull clock event/surce driver changes from Daniel Lezcano:
- Add sama5d2 support and rework the 32kHz clock handling (Alexandre Belloni)
- Add the high resolution support for SMP/SMT on the Ingenic timer (Zhou Yanjie)
- Add support for i.MX TPM driver with ARM64 (Anson Huang)
- Fix typo by replacing KHz to kHz (Geert Uytterhoeven)
- Add 32kHz support by setting the minimum ticks to 5 on Nomadik MTU (Linus Walleij)
- Replace HTTP links with HTTPS ones for security reasons (Alexander A. Klimov)
- Add support for the Ingenic X1000 OST (Zhou Yanjie)
SOM and it's Rock Pi N8 icarnation. This brings some arm64 dts-changes
with it as the underlying Dalang carrier board is shared by both
an arm32 rk3288 SOM and an arm64 rk3399 SOM (Rock Pi N10).
Other than that rk3288 gets its ohci node added that only works
on the fixed rk3288w variant of the soc and some asorted fixes
and improvements for dt-binding-check.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAl8YzOAQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgY9aB/0folCAovUA97bILQR/62PspVGR1i/S2GJe
sQqKuWDyBtJNM3IYNVMd/AtcrP+U0ZD4MX6TKbabs+ZuIc4EksXRroMTMm2azme1
rOrQuGSKcdhPobJOHlpbSC/QPWWi5GGGWDnwXY8T68NedeYLP/o8sOmZQtUi80R9
ueP5ZwiviwMrVzRITPb8sB89WEyRqaas2H0fc/4OjGRY/jeTKwCk9sP/JytA6gUB
/GXn+uUk5WcRkekujBi1LVi4BIhm7PMW9kM1AHWAV6+2Yd8uFyG4ut9MB7SmaQt8
QfEoPpLvQicpZCVB3VFOPJ38z4YuOXsqo85u8T3ZkgpLdInoa/J9
=GUhq
-----END PGP SIGNATURE-----
Merge tag 'v5.9-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt
Biggest part is the addition of the rk3288 variant of the VMARC
SOM and it's Rock Pi N8 icarnation. This brings some arm64 dts-changes
with it as the underlying Dalang carrier board is shared by both
an arm32 rk3288 SOM and an arm64 rk3399 SOM (Rock Pi N10).
Other than that rk3288 gets its ohci node added that only works
on the fixed rk3288w variant of the soc and some asorted fixes
and improvements for dt-binding-check.
* tag 'v5.9-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Add PCIe for RockPI N10
ARM: dts: rockchip: Add HDMI out for RockPI N8/N10
ARM: dts: rockchip: Add USB for RockPI N8/N10
ARM: dts: rockchip: Add usb host0 ohci node for rk3288
ARM: dts: rockchip: Fix VBUS on rk3288-vyasa
ARM: dts: rockchip: Add Radxa Rock Pi N8 initial support
ARM: dts: rockchip: Add VMARC RK3288 SOM initial support
dt-bindings: arm: rockchip: Add Rock Pi N8 binding
arm64: dts: rk3399pro: vmarc-som: Move common properties into Carrier
arm64: dts: rk3399pro: vmarc-som: Move supply regulators into Carrier
arm64: dts: rk3399pro: vmarc-som: Fix sorting nodes, properties
ARM: dts: rockchip: dalang-carrier: Move i2c nodes into SOM
ARM: dts: rockchip: Add 'arm,pl330-periph-burst' for dmac
ARM: dts: rockchip: Add marvell BT irq config
ARM: dts: rockchip: rename label and nodename pinctrl subnodes that end with gpio
Link: https://lore.kernel.org/r/2472314.kD9Egx1jfM@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This enables the audio SRAM, DMA engine, I2S interface, and codec, hooks
them together and adds a audio-graph-card instance.
It also removes the jack gpios from the gpio-keys instance, because the
audio jack driver registers an input device.
Link: https://lore.kernel.org/r/20200718205019.184927-10-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This memory is region is where the two-channel audio DMA can pump sound
samples into the SSPA's internal FIFO.
Link: https://lore.kernel.org/r/20200718205019.184927-6-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The ACGR register is at the offset of 0x1024, beyond the 4k originally
assigned to the MPMU range.
Link: https://lore.kernel.org/r/20200718205019.184927-5-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The power management unit, described by the soc_clocks node, controls the
power to the peripherals by the means of power domains with a single
cell -- the domain number.
Link: https://lore.kernel.org/r/20200718205019.184927-4-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
On the XO-1.75, this node represents a bus interface that operates in slave
mode and thus is only able to accommodate a single subnode; no address
cells are necessary.
The Documentation/devicetree/bindings/spi/spi-controller.yaml binding
prefers that we drop the property instead of setting it to zero.
This fixes a DT validation error:
arch/arm/boot/dts/mmp2-olpc-xo-1-75.dt.yaml: spi@d4037000:
{ ... } is valid under each of {'required': ['spi-slave']},
{'required': ['#address-cells']}
We also need to drop #size-cells:
arch/arm/boot/dts/mmp2-olpc-xo-1-75.dt.yaml: spi@d4037000:
'#address-cells' is a dependency of '#size-cells'
Link: https://lore.kernel.org/r/20200718205019.184927-3-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
mmp2-olpc-xo-1-75.dt.yaml: camera_i2c: $nodename:0:
'camera_i2c' does not match '^i2c(@.*)?'
mmp2-olpc-xo-1-75.dt.yaml: camera_i2c: 'sda-gpios' is a required property
mmp2-olpc-xo-1-75.dt.yaml: camera_i2c: 'scl-gpios' is a required property
The "gpios" property actually was documented as deprecated, but got dropped
in commit 0175ce4a58 ("dt-bindings: i2c: Convert i2c-gpio binding to
json-schema"). It's probably best kept forgotten though.
Link: https://lore.kernel.org/r/20200718205019.184927-2-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Highlights:
----------
MCU part:
-Enable stmpe811 on stm32f429
-Enable l3gd20-gyro on stm32f429
-Enable panel-ilitek-9341 on stm32f429
-Fixes for yaml validation (leds, nodes names,
remove useless bindings ...)
-Add stm32xxx compatibles for syscon nodes
MPU part:
-Add support for usb role switch to dwc2
-Add stm32xxx compatibles for syscon nodes
-Update uart4 pin configuration for low power mode
used by dkx and ed1 ST boards
-Fix uart nodes ordering and uart7_pins_a comments
-Add the support of uart instances available on STM32MP157 boards:
- usart3 on stm32mp157c-ev1, stm32mp157a-dk1, and stm32mp157c-dk2
- uart7 on stm32mp157a-dk1 and stm32mp157c-dk2
- usart2 on stm32mp157c-dk2
-Configure I2C5 on stm32mp15 DK boards
-----BEGIN PGP SIGNATURE-----
iQJMBAABCgA2FiEEctl9+nxzUSUqdELdf5rJavIecIUFAl8YQ6AYHGFsZXhhbmRy
ZS50b3JndWVAc3QuY29tAAoJEH+ayWryHnCFzGsP/A+rZHA3rpQXros5WEj/PV2+
1ePtLCXHW1mkhcsPQJb3p0bziGsVI8at2DMSlpeh6Koh+U8UkzD04Md4roqVWenM
XB6R6LBMuNVn2U3n3D7wGrcbkGPHTY/6lwpuyUqcm43yT8KhK1kLOdblSdeudZw6
JPowhZVk2uUXQRBr2RDZczSVYs5nAoB6qviuUN//LHVcTh/EyRAfOsB3Mdym2kqq
9umMqTLpznae5z648TdHJnDgqi/OKAFemQaLrl43dAnrZ0WfGuOfdApdlCAXfspg
RJ7Ciheba2Gd2RGAPHEhTN3+1DWErpxk2OhrhWt6YeTggkx+3V0psub807EXpZew
K1Y2xkrzPnL1uR0sK90bYVw2o+XUn08fckm7wWCWHwMKOp7WFPjBJj+CWIePAN0g
TIriAsBusxB/tN0wJJujPDvkXkZXkxo+l2P7BmY/KiXw7hhQVBsOmK+Gat56o1Ib
EkHLxUmdn0e1pJjN8DOsIA91MekEznnQ7QcQSGVdaYJXCUq8YUfB1t3Syjg1H4Vr
3RqEgbsaOva2MOKiNZ1iNWQkmmaRAmedSn0FTeQEyHu6ZULABtDApBbiKXjL8Gqf
Iw06PYjEN45r0UeOlLaSWQIRlfnRC17isFDfT9VxCEV3R84RBm7hA6VfLDvFEgj/
tC4AWykV22sYgMRn9wOg
=ga5j
-----END PGP SIGNATURE-----
Merge tag 'stm32-dt-for-v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/dt
STM32 DT updates for v5.9, round 1
Highlights:
----------
MCU part:
-Enable stmpe811 on stm32f429
-Enable l3gd20-gyro on stm32f429
-Enable panel-ilitek-9341 on stm32f429
-Fixes for yaml validation (leds, nodes names,
remove useless bindings ...)
-Add stm32xxx compatibles for syscon nodes
MPU part:
-Add support for usb role switch to dwc2
-Add stm32xxx compatibles for syscon nodes
-Update uart4 pin configuration for low power mode
used by dkx and ed1 ST boards
-Fix uart nodes ordering and uart7_pins_a comments
-Add the support of uart instances available on STM32MP157 boards:
- usart3 on stm32mp157c-ev1, stm32mp157a-dk1, and stm32mp157c-dk2
- uart7 on stm32mp157a-dk1 and stm32mp157c-dk2
- usart2 on stm32mp157c-dk2
-Configure I2C5 on stm32mp15 DK boards
* tag 'stm32-dt-for-v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (38 commits)
ARM: dts: stm32: enable usb-role-switch on USB OTG on stm32mp15xx-dkx
ARM: dts: stm32: Add compatibles for syscon for stm32mp151
ARM: dts: stm32: Add compatibles for syscon for stm32h743
ARM: dts: stm32: Add compatibles for syscon for stm32f746
ARM: dts: stm32: Add compatibles for syscon for stm32f426
dt-bindings: arm: stm32: Add compatibles for syscon nodes
ARM: dts: stm32: Fix spi4 pins in stm32mp15-pinctrl
ARM: dts: stm32: configure i2c5 support on stm32mp15xx-dkx
ARM: dts: stm32: add usart2 node to stm32mp157c-dk2
ARM: dts: stm32: add uart7 support to stm32mp15xx-dkx boards
ARM: dts: stm32: add usart3 node to stm32mp157c-ev1
ARM: dts: stm32: add usart3 node to stm32mp15xx-dkx boards
ARM: dts: stm32: add usart2, usart3 and uart7 pins in stm32mp15-pinctrl
ARM: dts: stm32: cosmetic updates in stm32mp15-pinctrl
ARM: dts: stm32: fix uart7_pins_a comments in stm32mp15-pinctrl
ARM: dts: stm32: fix uart nodes ordering in stm32mp15-pinctrl
ARM: dts: stm32: Update UART4 pin states on stm32mp15xx-dkx
ARM: dts: stm32: Update pin states for uart4 on stm32mp157c-ed1
ARM: dts: stm32: update uart4 pin configuration for low power on stm32mp157
dt-bindings: usb: dwc2: Fix issues for stm32mp15x SoC
...
Link: https://lore.kernel.org/r/8a9bb27b-fc08-126a-11f7-01354e8577e1@st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
1. Enable Bluetooth on Artik5 (Exynos3250).
2. Enable accelerometer on Aries boards (Samsung Galaxy S family,
S5Pv210); multiple fixes.
3. Fix highest frequencies on Exynos5800.
4. Fix rare USB instability on Odroid XU3 family (Exynos5422).
5. Minor DTS fixes and adjustments with dtschema.
-----BEGIN PGP SIGNATURE-----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=k3pO
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v5.9
1. Enable Bluetooth on Artik5 (Exynos3250).
2. Enable accelerometer on Aries boards (Samsung Galaxy S family,
S5Pv210); multiple fixes.
3. Fix highest frequencies on Exynos5800.
4. Fix rare USB instability on Odroid XU3 family (Exynos5422).
5. Minor DTS fixes and adjustments with dtschema.
* tag 'samsung-dt-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Replace HTTP links with HTTPS ones
ARM: dts: exynos: Disable frequency scaling for FSYS bus on Odroid XU3 family
ARM: dts: exynos: Define fixed regulators in root node for consistency in SMDK5420
ARM: dts: exynos: Define fixed regulators in root node for consistency in Arndale
ARM: dts: exynos: Define fixed regulators in root node for consistency in Origen
ARM: dts: exynos: Remove DMA controller bus node name to fix dtschema warnings
ARM: dts: exynos: Fix missing empty reg/ranges property regulators on Trats
ARM: dts: exynos: Align L2 cache-controller nodename with dtschema
ARM: dts: s5pv210: Correct BCM4329 bluetooth node
ARM: dts: s5pv210: Add BMA023 accelerometer support to Aries
ARM: dts: s5pv210: Add support for GP2A light sensor on Aries
ARM: dts: s5pv210: Correct fuelgauge definition on Aries
ARM: dts: s5pv210: Add interrupt-controller property to gph3
ARM: dts: exynos: Enable Bluetooth support for Artik5 board
ARM: dts: exynos: Extend all Exynos5800 A15's OPPs with max voltage data
Link: https://lore.kernel.org/r/20200721180900.13844-2-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add QFPROM and ethernet for ipq8064 and a new DTS for the MikroTik
RB3011 using the same platform.
-----BEGIN PGP SIGNATURE-----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=wWXD
-----END PGP SIGNATURE-----
Merge tag 'qcom-dts-for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt
Qualcomm ARM dts updates for v5.9
Add QFPROM and ethernet for ipq8064 and a new DTS for the MikroTik
RB3011 using the same platform.
* tag 'qcom-dts-for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
ARM: dts: qcom: add qfprom definition to ipq806x
ARM: dts: qcom: Add MikroTik RB3011
ARM: dts: qcom: add ethernet definitions to ipq8064
Link: https://lore.kernel.org/r/20200721045032.3430395-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
support, including:
- CPUFreq / Thermal throttling support for the H5
- Touchscreen support for the Pinephone
- New boards: PinePhone v1.2
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXxWlZAAKCRDj7w1vZxhR
xft/AQCaR2CkyOVyK32yPUX0ZF2nS+LYzalJIUpOuLhy37GQVwEA+vlQTa7fKdtW
4IX58peBkRD8FwTszrwR/tImDPd8Rwg=
=z8pA
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
Our usual number of patches to improve the Allwinner Device Tree
support, including:
- CPUFreq / Thermal throttling support for the H5
- Touchscreen support for the Pinephone
- New boards: PinePhone v1.2
* tag 'sunxi-dt-for-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: h5: bananapi-m2-plus-v1.2: Tie in CPU OPPs
arm64: dts: allwinner: h5: libretech-all-h3-cc: Tie in CPU OPPs
arm64: dts: allwinner: h5: Add CPU Operating Performance Points table
arm64: dts: allwinner: h5: Add trip and cooling maps to CPU thermal zones
arm64: dts: allwinner: h5: Add clock to CPU cores
ARM: dts: sunxi: bananapi-m2-plus-v1.2: Fix CPU supply voltages
ARM: dts: sunxi: bananapi-m2-plus-v1.2: Add regulator supply to all CPU cores
ARM: dts: sunxi: libretech-all-h3-cc: Add regulator supply to all CPU cores
arm64: dts: sun50i-pinephone: dldo4 must not be >= 1.8V
arm64: dts: allwinner: Add support for PinePhone revision 1.2
dt-bindings: arm: sunxi: Add PinePhone 1.2 bindings
arm64: dts: sun50i-a64-pinephone: Add touchscreen support
arm64: dts: sun50i-a64-pinephone: Enable LCD support on PinePhone
ARM: dts: orange-pi-zero-plus2: add leds configuration
ARM: dts: orange-pi-zero-plus2: enable USB OTG port
Link: https://lore.kernel.org/r/fa48ffcb-3404-41bb-b065-a16717cf5688.lettre@localhost
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
just a single patch fixing up the node names for schema.
-----BEGIN PGP SIGNATURE-----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=xBG2
-----END PGP SIGNATURE-----
Merge tag 'versatile-for-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into arm/dt
Versatile DTS changes for the v5.9 kernel cycle, essentially
just a single patch fixing up the node names for schema.
* tag 'versatile-for-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: dts: arm-realview: Align L2 cache-controller nodename with dtschema
Link: https://lore.kernel.org/r/CACRpkdbkM9ZmuG2FnBmO7upcJfnqq2oSLDCFDXC5b3K+dtps9Q@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- New board support: Protonic PRTI6Q/WD2/VT7/RVT and MYiR MYS-6ULX SBC.
- Update IIM, OCOTP and SD/MMC device node name to match .yaml bindings.
- Make tempmon node as child of anatop node according to hardware
architecture.
- The vf610-zii device update: configure fiber port to 1000BaseX, add
switch watchdog, MDIO speed and preamble.
- A series from Fabio Estevam to update imx6qdl-sabresd and
imx6q-tbs2910 for using MDIO node and reset-assert-us.
- Align L2 cache-controller device node name with .yaml schema.
- Enable SATA support for imx6qp-sabreauto and imx6qp-sabresd board.
- A series of patches from Shengjiu Wang to enable various audio
support on i.MX6 devices.
- Add Gateworks System Controller support for imx6qdl-gw devices.
- Change default #pwm-cells setting to <3> in the SoC dtsi files.
- Other small random changes.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl8VVgcUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM7azwf+KzAukegArKtAmsbAnYNKYztXXifW
6Hc3+hv2mfUtsGfHPSUJJ5MhEW52xAbcXnYETUkmoWe1W1zIxrNNWvBUm4nPF5os
0cO8tjk4cE4CYDnsl8sBSqT55sd3ke61I+j9q0NAQNyX9OlmZ3kfm8yw0yIsxTKp
/FzoLmOeRzhVKHdZczuJ9Ts4kFyf3XtQrrN1UTbu715KdIbbsrJtXQ74ADBCnjfX
8RUm3Y5XIaPcF4z2U8reMsbHCF120ENIfGwFRNo/Odx+1OVo1IrDB1+f/SP9ZP0T
6+iKvfSS4RavzB1tvLdJ2/911t7qtqsneU33kwQKL0wrFZsT4ih42uBfpw==
=1hHY
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX device tree update for 5.9:
- New board support: Protonic PRTI6Q/WD2/VT7/RVT and MYiR MYS-6ULX SBC.
- Update IIM, OCOTP and SD/MMC device node name to match .yaml bindings.
- Make tempmon node as child of anatop node according to hardware
architecture.
- The vf610-zii device update: configure fiber port to 1000BaseX, add
switch watchdog, MDIO speed and preamble.
- A series from Fabio Estevam to update imx6qdl-sabresd and
imx6q-tbs2910 for using MDIO node and reset-assert-us.
- Align L2 cache-controller device node name with .yaml schema.
- Enable SATA support for imx6qp-sabreauto and imx6qp-sabresd board.
- A series of patches from Shengjiu Wang to enable various audio
support on i.MX6 devices.
- Add Gateworks System Controller support for imx6qdl-gw devices.
- Change default #pwm-cells setting to <3> in the SoC dtsi files.
- Other small random changes.
* tag 'imx-dt-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (43 commits)
ARM: dts: vf610-zii-ssmb-spu3: Add node for switch watchdog
ARM: dts: vf610-zii-ssmb-dtu: Add no-sdio/no-sd properties
ARM: dts: imx6q-tbs2910: Pass reset-assert-us
ARM: dts: imx6q-tbs2910: Add an mdio node
ARM: dts: imx6qdl-sabresd: Pass reset-assert-us
ARM: dts: imx6qdl-sabresd: Add an mdio node
ARM: dts: imx6qdl-gw: add Gateworks System Controller support
ARM: dts: imx6ull: add MYiR MYS-6ULX SBC
ARM: dts: vf610-zii-spb4: Add node for switch watchdog
ARM: dts: colibri-imx6: remove pinctrl-names orphan
ARM: dts: imx: default to #pwm-cells = <3> in the SoC dtsi files
ARM: dts: vf610-zii-scu4-aib: Configure fibre ports to 1000BaseX
ARM: dts: vf610-zii-dev-rev-c: Configure fiber port to 1000BaseX
ARM: dts: ZII: update MDIO speed and preamble
ARM: dts: vfxxx: Add node for CAAM
ARM: dts: imx6qp-sabresd: enable sata
ARM: dts: imx6qp-sabreauto: enable sata
ARM: dts: add Protonic RVT board
ARM: dts: add Protonic VT7 board
ARM: dts: add Protonic WD2 board
...
Link: https://lore.kernel.org/r/20200720085536.24138-3-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- A couple of FEC2 phy-mode fixes on imx6sx-sabreauto and imx6sx-sdb
board.
- One fix on imx6qdl-icore pin muxing to get USB OTG_ID and SD card
detect work correctly.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl8VFn0UHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM52gQf+OGrSQq1t77ltL5EKeeV8f+PCu7UP
X7I2IJY+9FIYA1wuu0/AuhHaJ9NR0hN2mZVT+ktmxIDMVuHZJpAuHRfGp7anfVKr
vo1JgT9CbVZ/kD0n5a6TN28Kb7DVkIM4QGcEJuCD2mb1UJarlVX8YHg9Otv7b26p
3arPLR8eocPh2jNNdYnwSoZ8Li7Dm1SQloRAoCJOHAgAuSAdhG15rJBG70zX0F7d
QEWu6tNjN8FSrWeT1GLlzywYxGp1t592yuUpKAoppuJgxyUPIYA15vRB0d/KRqUL
CWYrDNh/dAvafI9HfeQQK5BjQhW58gy2c38s+bR9iPGoy88GzZiy+AatYQ==
=NlnX
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.8, round 3:
- A couple of FEC2 phy-mode fixes on imx6sx-sabreauto and imx6sx-sdb
board.
- One fix on imx6qdl-icore pin muxing to get USB OTG_ID and SD card
detect work correctly.
* tag 'imx-fixes-5.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6qdl-icore: Fix OTG_ID pin and sdcard detect
ARM: dts: imx6sx-sabreauto: Fix the phy-mode on fec2
ARM: dts: imx6sx-sdb: Fix the phy-mode on fec2
Link: https://lore.kernel.org/r/20200720040148.GA20462@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
were failing on older SoCs and one to fix Cedrus on the H6.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXxWlyQAKCRDj7w1vZxhR
xcNtAQDO2rSFHGpQsUE/MCRxMqd2c2OQ9zpovRnirnyJqLCPEwD/b8GAi9tfJksM
lmghSQnByq6Sqm9UA/i6jjLfz//4iQg=
=JoYD
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes
Two fixes for the Allwinner SoCs, one to relax the CMA allocation ranges that
were failing on older SoCs and one to fix Cedrus on the H6.
* tag 'sunxi-fixes-for-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: h6: Fix Cedrus IOMMU usage
ARM: dts sunxi: Relax a bit the CMA pool allocation range
Link: https://lore.kernel.org/r/e24f0608-6a4f-4163-b99e-a5f48e796184.lettre@localhost
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds support to enable HDMI out for
N10 and N8 combinations SBCs.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Link: https://lore.kernel.org/r/20200720110230.367985-2-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Radxa dalang carrier board has 2x USB 2.0 and 1x USB 3.0
ports.
This patch adds support to enable all these USB ports for
N10 and N8 combinations SBCs.
Note that the USB 3.0 port on RockPI N8 combination works
as USB 2.0 OTG since it is driven from RK3288.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20200720110230.367985-1-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
rk3288 and rk3288w have a usb host0 ohci controller.
Although rk3288 ohci doesn't actually work on hardware, but
rk3288w ohci can work well.
So add usb host0 ohci node in rk3288 dtsi and boards
can then enable it if supported.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Cc: William Wu <william.wu@rock-chips.com>
Link: https://lore.kernel.org/r/20200720105846.367776-1-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
[nsekhar@ti.com: drop obsolete hawkboard.org URL completeley
fixup subject line prefix]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Now that USB OTG driver supports usb role switch by overriding PHY input
signals (A-Valid, B-Valid and Vbus-Valid), enable it on stm32mp15xx-dkx.
dr_mode needn't to be forced to Peripheral anymore, it is set to OTG in
SoC device tree.
USB role (USB_ROLE_NONE, USB_ROLE_DEVICE, USB_ROLE_HOST) will be provided
by STUSB1600 Type-C controller driver.
This patch depends on "Add STUSB160x Type-C port controller support"
series, which is under review.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Syscon nodes needs at least 2 compatibles to be compliant why yaml documentation.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Syscon nodes needs at least 2 compatibles to be compliant why yaml documentation.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Syscon nodes needs at least 2 compatibles to be compliant why yaml documentation.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Syscon nodes needs at least 2 compatibles to be compliant why yaml documentation.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Move spi4_pins_a nodes from pinctrl_z to pinctrl as the associated pins
are not in BANK Z.
Fixes: 498a701498 ("ARM: dts: stm32: Add missing pinctrl entries for STM32MP15")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Configure I2C5 on stm32mp15 DK boards. It's available and can be used on:
- Arduino connector
- GPIO expansion connector
Keep it disabled by default, so the pins are kept in their initial state to
lower power consumption. This way they can also be used as GPIO.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Adds the usart2 node to stm32mp157c-dk2 board. usart2 pins are connected
to Bluetooth component. usart2 is disabled by default.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Adds uart7 node to stm32mp15xx-dkx and uart7 alias to stm32mp157a-dk1 and
stm32mp157c-dk2 boards. uart7 pins are connected to Arduino connector.
uart7 is disabled by default.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Adds the usart3 node to stm32mp157c-ev1 board. usart3 pins are connected to
GPIO Expansion connector. usart3 is disabled by default.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Adds usart3 node to stm32mp15xx-dkx and usart3 alias to stm32mp157a-dk1
and stm32mp157c-dk2 boards. usart3 pins are connected to GPIO Expansion
connector. usart3 is disabled by default.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Adds usart2_pins_c, usart3_pins_b, usart3_pins_c and uart7_pins_c pins
configurations in stm32mp15-pinctrl.
- usart2_pins_c pins are connected to Bluetooth chip on dk2 board.
- usart3_pins_b pins are connected to GPIO expansion connector on evx board.
- usart3_pins_c pins are connected to GPIO expansion connector on dkx board.
- uart7_pins_c pins are connected to Arduino Uno connector on dkx board.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Use tabs where possible and remove multiple blanks lines.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The Bananapi M2+ uses a GPIO line to change the effective resistance of
the CPU supply regulator's feedback resistor network. The voltages
described in the device tree were given directly by the vendor. This
turns out to be slightly off compared to the real values.
The updated voltages are based on calculations of the feedback resistor
network, and verified down to three decimal places with a multi-meter.
Fixes: 6eeb4180d4 ("ARM: dts: sunxi: h3-h5: Add Bananapi M2+ v1.2 device trees")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200717160053.31191-4-wens@kernel.org
The device tree currently only assigns the a supply for the first CPU
core, when in reality the regulator supply is shared by all four cores.
This might cause an issue if the implementation does not realize the
sharing of the supply.
Assign the same regulator supply to the remaining CPU cores to address
this.
Fixes: 6eeb4180d4 ("ARM: dts: sunxi: h3-h5: Add Bananapi M2+ v1.2 device trees")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200717160053.31191-3-wens@kernel.org
The device tree currently only assigns the a supply for the first CPU
core, when in reality the regulator supply is shared by all four cores.
This might cause an issue if the implementation does not realize the
sharing of the supply.
Assign the same regulator supply to the remaining CPU cores to address
this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200717160053.31191-2-wens@kernel.org
Since commit bcf3440c6d ("net: phy: micrel: add phy-mode support for the
KSZ9031 PHY"), networking is broken on sama5d3 xplained.
The device tree has phy-mode = "rgmii" and this worked before, because
KSZ9031 PHY started with default RGMII internal delays configuration (TX
off, RX on 1.2 ns) and MAC provided TX delay. After above commit, the
KSZ9031 PHY starts handling phy mode properly and disables RX delay, as
result networking is become broken.
Fix it by switching to phy-mode = "rgmii-rxid" to reflect previous
behavior.
Fixes: bcf3440c6d ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200717233644.841080-1-alexandre.belloni@bootlin.com
Commit 1019fe2c72 ("ARM: dts: exynos: Adjust bus related OPPs to the
values correct for Exynos5422 Odroids") changed the parameters of the
OPPs for the FSYS bus. Besides the frequency adjustments, it also removed
the 'shared-opp' property from the OPP table used for FSYS_APB and FSYS
busses.
This revealed that in fact the FSYS bus frequency scaling never worked.
When one OPP table is marked as 'opp-shared', only the first bus which
selects the OPP sets the rate of its clock. Then OPP core assumes that
the other busses have been changed to that OPP and no change to their
clock rates are needed. Thus when FSYS_APB bus, which was registered
first, set the rate for its clock, the OPP core did not change the FSYS
bus clock later.
The mentioned commit removed that behavior, what introduced a regression
on some Odroid XU3 boards. Frequency scaling of the FSYS bus causes
instability of the USB host operation, what can be observed as network
hangs. To restore old behavior, simply disable frequency scaling for the
FSYS bus.
Reported-by: Willy Wolff <willy.mh.wolff.ml@gmail.com>
Fixes: 1019fe2c72 ("ARM: dts: exynos: Adjust bus related OPPs to the values correct for Exynos5422 Odroids")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
GPIOP7 is used in the Rainier design to manage the state of a
microcontroller elsewhere in the system but its ball, Y23, is the
driver of the heartbeat LED on the ast2600-evb and the SoC defaults Y23
at power-on to the pulse-train behaviour used to drive the LED. This
causes much confusion for the micro in the Rainier system, so hog the
line as early as possible.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The hub FSI master can access the cfams on two other processors. Reflect
this by adding a second cfam to the first hub description.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Tested-by: Andrew Geissler <geissonator@yahoo.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Rainier uses GPIO B6 as the checkstop GPIO. Define the line-name
so that this GPIO can be found by name.
Signed-off-by: Ben Tyner <ben.tyner@ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The attention handler will monitor the checkstop gpio via the character
device interface so it needs to not be defined.
Signed-off-by: Ben Tyner <ben.tyner@ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add a reserved memory node for the VGA memory. Add the XDMA engine node,
enable it, and point it's memory region to the VGA memory.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add a reserved memory node for the VGA memory. Add the XDMA engine node,
enable it, and point it's memory region to the VGA memory.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add the PCI-E root complex reset, correct the pcie-device property, and
add the Aspeed SCU interrupt controller include.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Correct the pcie-device property, and add the Aspeed SCU interrupt
controller include.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The current pin muxing scheme muxes GPIO_1 pad for USB_OTG_ID
because of which when card is inserted, usb otg is enumerated
and the card is never detected.
[ 64.492645] cfg80211: failed to load regulatory.db
[ 64.492657] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware
[ 76.343711] ci_hdrc ci_hdrc.0: EHCI Host Controller
[ 76.349742] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 2
[ 76.388862] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00
[ 76.396650] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.08
[ 76.405412] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 76.412763] usb usb2: Product: EHCI Host Controller
[ 76.417666] usb usb2: Manufacturer: Linux 5.8.0-rc1-next-20200618 ehci_hcd
[ 76.424623] usb usb2: SerialNumber: ci_hdrc.0
[ 76.431755] hub 2-0:1.0: USB hub found
[ 76.435862] hub 2-0:1.0: 1 port detected
The TRM mentions GPIO_1 pad should be muxed/assigned for card detect
and ENET_RX_ER pad for USB_OTG_ID for proper operation.
This patch fixes pin muxing as per TRM and is tested on a
i.Core 1.5 MX6 DL SOM.
[ 22.449165] mmc0: host does not support reading read-only switch, assuming write-enable
[ 22.459992] mmc0: new high speed SDHC card at address 0001
[ 22.469725] mmcblk0: mmc0:0001 EB1QT 29.8 GiB
[ 22.478856] mmcblk0: p1 p2
Fixes: 6df11287f7 ("ARM: dts: imx6q: Add Engicam i.CoreM6 Quad/Dual initial support")
Cc: stable@vger.kernel.org
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
esdhc0 is connected to an eMMC, so it is safe to pass the "no-sdio"/"no-sd"
properties.
esdhc1 is wired to a standard SD socket, so pass the "no-sdio" property.
Signed-off-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Commit 0672d22a19 ("ARM: dts: imx: Fix the AR803X phy-mode") fixed the
phy-mode for fec1, but missed to fix it for the fec2 node.
Fix fec2 to also use "rgmii-id" as the phy-mode.
Cc: <stable@vger.kernel.org>
Fixes: 0672d22a19 ("ARM: dts: imx: Fix the AR803X phy-mode")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Commit 0672d22a19 ("ARM: dts: imx: Fix the AR803X phy-mode") fixed the
phy-mode for fec1, but missed to fix it for the fec2 node.
Fix fec2 to also use "rgmii-id" as the phy-mode.
Cc: <stable@vger.kernel.org>
Fixes: 0672d22a19 ("ARM: dts: imx: Fix the AR803X phy-mode")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the AR8035 datasheet:
"When using crystal, the clock is generated internally after power is
stable. For a reliable power on reset, suggest to keep asserting the reset
low long enough (10ms) to ensure the clock is stable and clock-to-reset 1ms
requirement is satisfied."
Pass the 'reset-assert-us' property to describe such requirement.
While at it, use the 'reset-gpios' property inside the the mdio
node instead of the deprecated usage of 'phy-reset-gpios'.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx6q-tbs2910 has an Atheros AR8035 Ethernet PHY at address 4.
The AR8035 provides a 125MHz clock to the ENET_REF_CLK i.MX6 pin.
Improve the Ethernet representation by adding an mdio node with such
information.
This fixes an Ethernet regression in U-Boot as U-Boot AR803X driver now
expects the 'qca,clk-out-frequency' property to be passed via
device tree.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Soeren Moch <smoch@web.de>
Tested-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the AR8031 datasheet:
"When using crystal, clock is generated internally after the power is
stable. In order to get reliable power-on-reset, it is recommended to
keep asserting the reset low signal long enough (10 ms) to ensure the
clock is stable and clock-to-reset (1 ms) requirement is satisfied."
Pass the 'reset-assert-us' property to describe such requirement.
While at it, use the 'reset-gpios' property inside the the mdio
node instead of the deprecated usage of 'phy-reset-gpios'.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx6qdl-sabresd has an Atheros AR8031 Ethernet PHY at address 1.
The AR8031 provides a 125MHz clock to the ENET_REF_CLK i.MX6 pin.
Improve the Ethernet representation by adding an mdio node with such
information.
An advantage of adding the mdio node is that the AR8031 initialization
code in the mx6sabresd board file in U-Boot can totally be removed.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add Gateworks System Controller support to Gateworks Ventana boards:
- add dt bindings for GSC mfd driver and hwmon driver for ADC's and
fan controllers.
- add dt bindings for gpio-keys driver for push-button and interrupt events
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The marvell PHY reg-init registers for the D-Link DNS-327L are wrong.
Currently the first field is used to set the page 2, but this is
pointless. The usage is not correct, and we are setting the wrong
registers.
Fix it.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Connect the voltage regulator of vbus to the otg connector.
Depending on the current mode this is enabled (in "host" mode")
or disabled (in "peripheral" mode). The regulator must be updated
if the controller is configured in "otg" mode and the status changes
between "host" and "peripheral".
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Link: https://lore.kernel.org/r/20200707101214.2301768-1-michael@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Rock Pi N8 is a Rockchip RK3288 based SBC, which has
- VMARC RK3288 SOM (as per SMARC standard) from Vamrs.
- Compatible carrier board from Radxa.
VAMRC RK3288 SOM need to mount on top of radxa dalang
carrier board for making Rock Pi N8 SBC.
So, add initial support for Rock Pi N8 by including rk3288,
rk3288 vamrc-som and raxda dalang carrier board dtsi files.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20200715083418.112003-8-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
VMARC RK3288 SOM is a standard SMARC SOM design with
Rockchip RK3288 SoC, which is designed by Vamrs.
Specification:
- Rockchip RK3288
- PMIC: RK808
- eMMC: 16GB/32GB/64GB
- SD slot
- 2xUSB-2.0, 1xUSB3.0
- USB-C for power supply
- Ethernet
- HDMI, MIPI-DSI/CSI, eDP
Add initial support for VMARC RK3288 SOM, this would use
with associated carrier board.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20200715083418.112003-7-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Some of gmac, sdmmc node properties are common across rk3288 and
rk3399pro SOM's so move them into Carrier dtsi.
Chosen node is specific to rk3399pro configure SBC, so move it into
RockPI N10 dts.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20200715083418.112003-5-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Supply regulators are common across different variants of vmarc SOM's
since the Type C power controller IC is part of the carrier board.
So, move the supply regulators into carrier board dtsi.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20200715083418.112003-4-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
I2C nodes and associated slave devices defined in Carrier board
are specific to rk3399pro vmrac SOM.
So, move them into SOM dtsi.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20200715083418.112003-2-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This time there are a number of actual code fixes, plus
a small set of device tree issues getting addressed:
- Renesas:
- one defconfig cleanup to allow a later Kconfig change
- Intel socfpga:
- enable QSPI devices on some machines
- fix DTC validation warnings
- TI OMAP:
- Two DEBUG_ATOMIC_SLEEP fixes for ti-sysc interconnect target module
driver
- A regression fix for ti-sysc no-idle handling that caused issues
compared to earlier platform data based booting
- A fix for memory leak for omap_hwmod_allocate_module
- Fix d_can driver probe for am437x
- NXP i.MX
- A couple of fixes on i.MX platform device registration code to stop
the use of invalid IRQ 0.
- Fix a regression seen on ls1021a platform, caused by commit
52102a3ba6 ("soc: imx: move cpu code to drivers/soc/imx").
- Fix a misconfiguration of audio SSI on imx6qdl-gw551x board.
- Amlogic Meson
- misc DT fixes
- SoC ID fixes to detect all chips correctly
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=Xlng
-----END PGP SIGNATURE-----
Merge tag 'arm-fixes-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc into master
Pull ARM SoC fixes from Arnd Bergmann:
"This time there are a number of actual code fixes, plus a small set of
device tree issues getting addressed:
Renesas:
- one defconfig cleanup to allow a later Kconfig change
Intel socfpga:
- enable QSPI devices on some machines
- fix DTC validation warnings
TI OMAP:
- Two DEBUG_ATOMIC_SLEEP fixes for ti-sysc interconnect target
module driver
- A regression fix for ti-sysc no-idle handling that caused issues
compared to earlier platform data based booting
- A fix for memory leak for omap_hwmod_allocate_module
- Fix d_can driver probe for am437x
NXP i.MX:
- A couple of fixes on i.MX platform device registration code to
stop the use of invalid IRQ 0.
- Fix a regression seen on ls1021a platform, caused by commit
52102a3ba6 ("soc: imx: move cpu code to drivers/soc/imx").
- Fix a misconfiguration of audio SSI on imx6qdl-gw551x board.
Amlogic Meson:
- misc DT fixes
- SoC ID fixes to detect all chips correctly"
* tag 'arm-fixes-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
arm64: dts: spcfpga: Align GIC, NAND and UART nodenames with dtschema
ARM: dts: socfpga: Align L2 cache-controller nodename with dtschema
arm64: dts: stratix10: increase QSPI reg address in nand dts file
arm64: dts: stratix10: add status to qspi dts node
arm64: dts: agilex: add status to qspi dts node
ARM: dts: Fix dcan driver probe failed on am437x platform
ARM: OMAP2+: Fix possible memory leak in omap_hwmod_allocate_module
arm64: defconfig: Enable CONFIG_PCIE_RCAR_HOST
soc: imx: check ls1021a
ARM: imx: Remove imx_add_imx_dma() unused irq_err argument
ARM: imx: Provide correct number of resources when registering gpio devices
ARM: dts: imx6qdl-gw551x: fix audio SSI
bus: ti-sysc: Do not disable on suspend for no-idle
bus: ti-sysc: Fix sleeping function called from invalid context for RTC quirk
bus: ti-sysc: Fix wakeirq sleeping function called from invalid context
ARM: dts: meson: Align L2 cache-controller nodename with dtschema
arm64: dts: meson-gxl-s805x: reduce initial Mali450 core frequency
arm64: dts: meson: add missing gxl rng clock
soc: amlogic: meson-gx-socinfo: Fix S905X3 and S905D3 ID's
This adds device trees for the ASUS Google Nexus 7 and Acer Iconia Tab
A500. In addition there are a slew of fixes to existing device trees in
preparation for validating the DTBs against json-schema.
-----BEGIN PGP SIGNATURE-----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=oFYm
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.9-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
ARM: tegra: Device tree changes for v5.9-rc1
This adds device trees for the ASUS Google Nexus 7 and Acer Iconia Tab
A500. In addition there are a slew of fixes to existing device trees in
preparation for validating the DTBs against json-schema.
* tag 'tegra-for-5.9-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (38 commits)
ARM: tegra: Add device-tree for ASUS Google Nexus 7
ARM: tegra: Add device-tree for Acer Iconia Tab A500
ARM: tegra: Add HDMI supplies on Nyan boards
ARM: tegra: Add missing DSI controller on Tegra30
ARM: tegra: Add i2c-bus subnode for DPAUX controllers
ARM: tegra: The Tegra30 SDHCI is not backwards-compatible
ARM: tegra: The Tegra30 DC is not backwards-compatible
ARM: tegra: Remove spurious comma from node name
ARM: tegra: Add parent clock to DSI output
ARM: tegra: Use standard names for SRAM nodes
ARM: tegra: seaboard: Use standard battery bindings
ARM: tegra: Use standard names for LED nodes
ARM: tegra: Use numeric unit-addresses
ARM: tegra: medcom-wide: Remove extra panel power supply
ARM: tegra: Use proper unit-addresses for OPPs
ARM: tegra: Add missing clock-names for SDHCI controllers
ARM: tegra: Fix order of XUSB controller clocks
ARM: tegra: Add #reset-cells to Tegra124 memory controller
ARM: tegra: Add missing panel power supplies
ARM: tegra: Add micro-USB A/B port on Jetson TK1
...
Link: https://lore.kernel.org/r/20200717161300.1661002-5-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The device node for the FIFO-buffered Serial Interface sound node lacks
the "clocks" property, as the DTS file didn't describe any clocks yet at
its introduction.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200519075525.24742-1-geert+renesas@glider.be
Fix dtschema validator warnings like:
l2-cache: $nodename:0: 'l2-cache' does not match '^(cache-controller|cpu)(@[0-9a-f,]+)*$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
A series of changes to configure IPU and DSP remoteproc for omap4 & 5.
And a change to configure the default mux for am335x-pocketbeagle, and
a change to use https for external links.
-----BEGIN PGP SIGNATURE-----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=IlyP
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.9/dt-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
More dts changes for omaps for v5.9
A series of changes to configure IPU and DSP remoteproc for omap4 & 5.
And a change to configure the default mux for am335x-pocketbeagle, and
a change to use https for external links.
* tag 'omap-for-v5.9/dt-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
Replace HTTP links with HTTPS ones: OMAP DEVICE TREE SUPPORT
ARM: dts: omap5-uevm: Add watchdog timers for IPU and DSP
ARM: dts: omap4-panda-common: Add watchdog timers for IPU and DSP
ARM: dts: omap5-uevm: Add system timers to DSP and IPU
ARM: dts: omap5-uevm: Add CMA pools and enable IPU & DSP
ARM: dts: omap5: Add aliases for rproc nodes
ARM: dts: omap5: Add DSP and IPU nodes
ARM: dts: omap4-panda-common:: Add system timers to DSP and IPU
ARM: dts: omap4-panda-common: Add CMA pools and enable IPU & DSP
ARM: dts: omap4: Add aliases for rproc nodes
ARM: dts: omap4: Add IPU DT node
ARM: dts: omap4: Update the DSP node
ARM: dts: omap5: Add timer_sys_ck clocks for timers
ARM: dts: omap4: Add timer_sys_ck clocks for timers
ARM: dts: am335x-pocketbeagle: set default mux for gpio pins
Link: https://lore.kernel.org/r/pull-1594838111-649880@atomide.com-3
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A series of changes to drop remaining USB platform data for omap4/5,
and am4, and dra7.
And a patch to drop AES platform data for omap3.
-----BEGIN PGP SIGNATURE-----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=4iOb
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.9/ti-sysc-drop-pdata-take2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
Drop more legacy platform data for omaps for v5.9
A series of changes to drop remaining USB platform data for omap4/5,
and am4, and dra7.
And a patch to drop AES platform data for omap3.
* tag 'omap-for-v5.9/ti-sysc-drop-pdata-take2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Drop legacy platform data for omap5 usb host
ARM: OMAP2+: Drop legacy platform data for omap4 usb
ARM: OMAP2+: Drop legacy platform data for dra7 dwc3
ARM: OMAP2+: Drop legacy platform data for omap5 dwc3
ARM: OMAP2+: Drop legacy platform data for am4 dwc3
bus: ti-sysc: Add missing quirk flags for usb_host_hs
ARM: dts: omap3: Migrate AES from hwmods to sysc-omap2
Link: https://lore.kernel.org/r/pull-1594838111-649880@atomide.com-2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Few fixes for issues noticed during testing:
- Two DEBUG_ATOMIC_SLEEP fixes for ti-sysc interconnect target module
driver
- A regression fix for ti-sysc no-idle handling that caused issues
compared to earlier platform data based booting
- A fix for memory leak for omap_hwmod_allocate_module
- Fix d_can driver probe for am437x
-----BEGIN PGP SIGNATURE-----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=ekbH
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.8/fixes-rc5-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for v5.8-rc cycle
Few fixes for issues noticed during testing:
- Two DEBUG_ATOMIC_SLEEP fixes for ti-sysc interconnect target module
driver
- A regression fix for ti-sysc no-idle handling that caused issues
compared to earlier platform data based booting
- A fix for memory leak for omap_hwmod_allocate_module
- Fix d_can driver probe for am437x
* tag 'omap-for-v5.8/fixes-rc5-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix dcan driver probe failed on am437x platform
ARM: OMAP2+: Fix possible memory leak in omap_hwmod_allocate_module
bus: ti-sysc: Do not disable on suspend for no-idle
bus: ti-sysc: Fix sleeping function called from invalid context for RTC quirk
bus: ti-sysc: Fix wakeirq sleeping function called from invalid context
Link: https://lore.kernel.org/r/pull-1594840100-132735@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- A couple of fixes on i.MX platform device registration code to stop
the use of invalid IRQ 0.
- Fix a regression seen on ls1021a platform, caused by commit
52102a3ba6 ("soc: imx: move cpu code to drivers/soc/imx").
- Fix a misconfiguration of audio SSI on imx6qdl-gw551x board.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl8Nxv4UHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM4fIAf/SKUzFbQ/INaU98yW8zONnZVzD/jI
3oTnBP87YJRNiyrLF1lWLs55vfnhum7yXJZXdMbwP55fdJKVaV4StePGz9Sh4Gba
4COHOF3XvF73b4kpcCQEr1U+Y0KHEfMbkwONmerk9ZkRThY2uqcRsdj4br+XA9eU
19ppWdOYZHMjegPu0KuxJlevZJDO6s9I4MCKFWmGgWhanLeGXXd2xtJEgqTWtTnS
EFjOFdBQF+5yd0VY/j6WHBDHWa/fXhDFoAO8Wc5LMCP3VybZdciIi4mN8y0UZoNG
Q5UnBvpYMCqrBwVlyqgeDtJUvYd+33dHqsRbU3KN8yBpRnyHupR9UvcFLA==
=+Gmy
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.8, round 2:
- A couple of fixes on i.MX platform device registration code to stop
the use of invalid IRQ 0.
- Fix a regression seen on ls1021a platform, caused by commit
52102a3ba6 ("soc: imx: move cpu code to drivers/soc/imx").
- Fix a misconfiguration of audio SSI on imx6qdl-gw551x board.
* tag 'imx-fixes-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx: check ls1021a
ARM: imx: Remove imx_add_imx_dma() unused irq_err argument
ARM: imx: Provide correct number of resources when registering gpio devices
ARM: dts: imx6qdl-gw551x: fix audio SSI
Link: https://lore.kernel.org/r/20200714145649.GP15718@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There are few hardware variants of NVIDIA Tegra30-based Nexus 7 device:
1. WiFi-only (named Grouper)
2. GSM (named Tilapia)
3. Using Maxim PMIC (E1565 board ID)
4. Using Ti PMIC (PM269 board ID)
This patch adds device-trees for known and tested variants.
Link: https://wiki.postmarketos.org/wiki/Google_Nexus_7_2012_(asus-grouper)
Tested-by: Pedro Ângelo <pangelo@void.io>
Tested-by: Matt Merhar <mattmerhar@protonmail.com>
Tested-by: Zack Pearsall <zpearsall@yahoo.com>
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Fix dtschema validator warnings like:
l2-cache@fffff000: $nodename:0:
'l2-cache@fffff000' does not match '^(cache-controller|cpu)(@[0-9a-f,]+)*$'
Fixes: 475dc86d08 ("arm: dts: socfpga: Add a base DTSI for Altera's Arria10 SOC")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
The SOR controller needs the AVDD I/O and VDD HDMI PLL supplies in order
to operate correctly. Make sure to specify them for Nyan boards.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra30 has a DSI controller, although it is never used on any of the
devices supported by the upstream Linux kernel.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DPAUX controller device tree bindings require the bus to have an
i2c-bus subnode to distinguish between I2C clients and pinmux groups.
Signed-off-by: Thierry Reding <treding@nvidia.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Got following d_can probe errors with kernel 5.8-rc1 on am437x
[ 10.730822] CAN device driver interface
Starting Wait for Network to be Configured...
[ OK ] Reached target Network.
[ 10.787363] c_can_platform 481cc000.can: probe failed
[ 10.792484] c_can_platform: probe of 481cc000.can failed with error -2
[ 10.799457] c_can_platform 481d0000.can: probe failed
[ 10.804617] c_can_platform: probe of 481d0000.can failed with error -2
actually, Tony has fixed this issue on am335x with the patch [3]
Since am437x has the same clock structure with am335x
[1][2], so reuse the code from Tony Lindgren's patch [3] to fix it.
[1]: https://www.ti.com/lit/pdf/spruh73 Chapter-23, Figure 23-1. DCAN
Integration
[2]: https://www.ti.com/lit/pdf/spruhl7 Chapter-25, Figure 25-1. DCAN
Integration
[3]: commit 516f1117d0 ("ARM: dts: Configure osc clock for d_can on
am335x")
Fixes: 1a5cd7c23c ("bus: ti-sysc: Enable all clocks directly during init to read revision")
Signed-off-by: dillon min <dillon.minfei@gmail.com>
[tony@atomide.com: aligned commit message a bit for readability]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull input fixes from Dmitry Torokhov:
"A few quirks for the Elan touchpad driver, another Thinkpad is being
switched over from PS/2 to native RMI4 interface, and we gave a brand
new SW_MACHINE_COVER switch definition"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elan_i2c - add more hardware ID for Lenovo laptops
Input: i8042 - add Lenovo XiaoXin Air 12 to i8042 nomux list
Revert "Input: elants_i2c - report resolution information for touch major"
Input: elan_i2c - only increment wakeup count on touch
Input: synaptics - enable InterTouch for ThinkPad X1E 1st gen
ARM: dts: n900: remove mmc1 card detect gpio
Input: add `SW_MACHINE_COVER`
Odroid-C1 has an eMMC connector where users can optionally install an
eMMC module. The eMMC modules run off a 1.8V VQMMC supply which means
that HS-200 mode can be used (this is the highest mode that the SDHC
controller supports). Enable the SDHC controller so eMMC modules can be
accessed.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200620163654.37207-4-martin.blumenstingl@googlemail.com
EC-100 has built-in eMMC flash which is hard-wired to 3.3V VCC (which
means it's limited to high-speed MMC modes). Enable the SDHC controller
to access the contents of the eMMC flash.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200620163654.37207-3-martin.blumenstingl@googlemail.com
Meson6, Meson8, Meson8b and Meson8m2 are using a similar SDHC controller
IP which typically connects to an eMMC chip (because unlike the SDIO
controller the SDHC controller has an 8-bit bus interface).
On Meson8, Meson8b and Meson8m2 the clock inputs are all the same.
However, Meson8m2 seems to have an improved version of the SHDC
controller IP which doesn't require the driver to wait manually for a
flush of a DMA transfer. Thus every SoC has it's own compatible string
so if more difference are discovered they can be implemented.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200620163654.37207-2-martin.blumenstingl@googlemail.com
The Meson8b SoCs have a power domain controller which can turn on/off
various register areas (such as: Ethernet, VPU, etc.).
Add the main "pwrc" controller and configure the Ethernet power domain.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200620161010.23171-4-martin.blumenstingl@googlemail.com
The Meson8m2 SoCs has introduced additional reset lines for the VPU
compared to Meson8. Also it uses a slightly different VPU clock
frequency compared to Meson8 since it can now achieve 364MHz thanks to
the addition of the GP_PLL.
Add the reset lines, VPU clock configuration and update the compatible
string so the implementation differences can be managed.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200620161010.23171-3-martin.blumenstingl@googlemail.com
The Meson8 SoCs have a power domain controller which can turn on/off
various register areas (such as: Ethernet, VPU, etc.).
Add the main "pwrc" controller and configure the Ethernet power domain.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200620161010.23171-2-martin.blumenstingl@googlemail.com
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The watchdog timers have been added for the IPU and DSP remoteproc
devices for the OMAP5 uEVM board. The following timers (same as the
timers on OMAP4 Panda boards) are used as the watchdog timers,
DSP : GPT6
IPU : GPT9 & GPT11 (one for each Cortex-M4 core)
The MPU-side drivers will use this data to initialize the watchdog
timers, and listen for any watchdog triggers. The BIOS-side code
needs to configure and refresh these timers properly to not throw
a watchdog error.
These timers can be changed or removed as per the system integration
needs, alongside appropriate equivalent changes on the firmware side.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The watchdog timers have been added for the IPU and DSP remoteproc
devices on all the OMAP4-based Panda boards. The following timers
are used as the watchdog timers,
DSP : GPT6
IPU : GPT9 & GPT11 (one for each Cortex-M3 core)
The MPU-side drivers will use this data to initialize the watchdog
timers, and listen for any watchdog triggers. The BIOS-side code
needs to configure and refresh these timers properly to not throw
a watchdog error.
These timers can be changed or removed as per the system integration
needs, alongside appropriate equivalent changes on the firmware side.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The BIOS System Tick timers have been added for the IPU and DSP
remoteproc devices for the OMAP5 uEVM boards. The following timers
(same as the timers on OMAP4 Panda boards) are chosen:
IPU : GPT3 (SMP-mode)
DSP : GPT5
IPU has two Cortex-M4 processors, and is currently expected to be
running in SMP-mode, so only a single timer suffices to provide
the BIOS tick timer. An additional timer should be added for the
second processor in IPU if it were to be run in non-SMP mode. The
timer value also needs to be unique from the ones used by other
processors so that they can be run simultaneously.
The timers are optional, but are mandatory to support device
management features such as power management and watchdog support.
The above are added to successfully boot and execute firmware images
configured with the respective timers, images that use internal
processor subsystem timers are not affected. The timers can be
changed or removed as per the system integration needs, alongside
equivalent changes on the firmware side.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for the IPU and DSP
remoteproc devices on the OMAP5 uEVM board. These nodes are assigned
to the respective rproc device nodes, and both the IPU and DSP remote
processors are enabled for this board.
The current CMA pools and sizes are defined statically for each device.
The starting addresses are fixed to meet current dependencies on the
remote processor firmwares, and will go away when the remote-side
code has been improved to gather this information runtime during
its initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add aliases for the DSP and IPU remoteproc processor
nodes common to all OMAP5 boards. The aliases uses
the stem "rproc", and are identical to the values
chosen on OMAP4 boards.
The aliases can be overridden, if needed, in the
respective board files.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP5, like OMAP4, also has two remote processor subsystems,
DSP and IPU. The IPU subsystem though has dual Cortex-M4
processors instead of the dual Cortex-M3 processors in OMAP4,
but otherwise has almost the same set of features. Add the
DT nodes for these two processor sub-systems for all OMAP5
SoCs.
The nodes have the 'iommus', 'clocks', 'resets', 'firmware' and
'mboxes' properties added, and are disabled for now. The IPU node
has its L2 RAM memory specified through the 'reg' and 'reg-names'
properties. The DSP node doesn't have these since it doesn't have
any L2 RAM memories, but has an additional 'ti,bootreg' property
instead as it has a specific boot register that needs to be
programmed for booting.
These nodes should be enabled as per the individual product
configuration in the corresponding board dts files.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The BIOS System Tick timers have been added for the IPU and DSP
remoteproc devices on all the OMAP4-based Panda boards. The
following DMTimers are chosen:
IPU : GPT3 (SMP-mode)
DSP : GPT5
IPU has two Cortex-M3 processors, and is currently expected to be
running in SMP-mode, so only a single timer suffices to provide
the BIOS tick timer. An additional timer should be added for the
second processor in IPU if it were to be run in non-SMP mode. The
timer value also needs to be unique from the ones used by other
processors so that they can be run simultaneously.
The timers are optional, but are mandatory to support device
management features such as power management and watchdog support.
The above are added to successfully boot and execute firmware images
configured with the respective timers, images that use internal
processor subsystem timers are not affected. The timers can be
changed or removed as per the system integration needs, alongside
equivalent changes on the firmware side.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for the IPU and DSP
remoteproc devices on all the OMAP4-based Panda boards. These nodes
are assigned to the respective rproc device nodes, and both the
IPU and DSP remote processors are enabled for all these boards.
The current CMA pools and sizes are defined statically for each device.
The starting addresses are fixed to meet current dependencies on the
remote processor firmwares, and will go away when the remote-side
code has been improved to gather this information runtime during
its initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add aliases for the DSP and IPU remoteproc processor
nodes common to all OMAP4 boards. The aliases uses
the stem "rproc".
The aliases can be overridden, if needed, in the
respective board files.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DT node for the Dual-Cortex M3 IPU processor sub-system has
been added for OMAP4 SoCs. The L2RAM memory region information
has been added to the node through the 'reg' and 'reg-names'
properties. The node has the 'iommus', 'clocks', 'resets',
'mboxes' and 'firmware' properties also added, and is disabled
for now. It should be enabled as per the individual product
configuration in the corresponding board dts files.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The compatible property for the DSP node is updated to match
the OMAP remoteproc bindings. The node is moved from the soc
node to the ocp node to better reflect the connectivity from
MPU side.
The node is updated with the 'ti,bootreg', 'clocks', 'resets',
'iommus', 'mboxes' and 'firmware' properties. Note that the
node does not have any 'reg' or 'reg-names' properties since
it doesn't have any L2 RAM memory, but only Unicaches.
The node is disabled for now, and should be enabled as per
the individual product configuration in the corresponding
board dts files.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The commit d41e530409 ("clk: ti: omap5: cleanup unnecessary clock
aliases") has cleaned up all timer_sys_ck clock aliases and retained
only the timer_32k_ck clock alias. The OMAP clocksource timer driver
though still uses this clock alias when reconfiguring the parent
clock source for the timer functional clocks, so add these clocks
to all the timer nodes except for the always-on timers 1 and 12.
This is required by the OMAP remoteproc driver to successfully
acquire a timer and configure the source clock to be driven from
timer_sys_ck clock.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The commit 1c7de9f27a ("clk: ti: omap4: cleanup unnecessary clock
aliases") has cleaned up all timer_sys_ck clock aliases and retained
only the timer_32k_ck clock alias. The OMAP clocksource timer driver
though still uses this clock alias when reconfiguring the parent
clock source for the timer functional clocks, so add these clocks
to all the timer nodes.
This is required by the OMAP remoteproc driver to successfully
acquire a timer and configure the source clock to be driven from
timer_sys_ck clock.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These pins on the PocketBeagle P1 and P2 headers are connected to AM3358
balls with gpio lines, and these pins are not used for any other
peripherals by default. These GPIO lines are unclaimed and could be used
by userspace program through the gpiod ABI.
This patch adds a "default" state in the am33xx_pinmux node and sets the
mux for those pins to gpio (mode 7) and input enable.
The "pinctrl-single,bias-pullup" and "pinctrl-single,bias-pulldown"
pinconf properties are also set for each pin per the ball reset state in
section 4.2 of the datasheet [0].
This is the AM335x pin control register format in Table 9-60 [1]:
bit attribute value
----------------------------------
31-7 reserved 0 on reset
6 slew { 0: fast, 1: slow }
5 rx_active { 0: rx disable, 1: rx enabled }
4 pu_typesel { 0: pulldown select, 1: pullup select }
3 puden { 0: pud enable, 1: disabled }
2 mode 3 bits to selec mode 0 to 7
1 mode
0 mode
The values for the bias pinconf properties are derived as follows:
pinctrl-single,bias-pullup = <[input] [enabled] [disable] [mask]>;
pinctrl-single,bias-pullup = < 0x10 0x10 0x10 0x18 >;
2^5 2^4 2^3 2^2 2^1 2^0 |
0x20 0x10 0x08 0x04 0x02 0x01 |
--------------------------------------------------|
input x 1 0 x x x | 0x10
enabled x 1 0 x x x | 0x10
disabled x 0 0 x x x | 0x00
mask x 1 1 x x x | 0x18
pinctrl-single,bias-pulldown = <[input] [enabled] [disable] [mask]>;
pinctrl-single,bias-pulldown = < 0x0 0x0 0x10 0x18 >;
2^5 2^4 2^3 2^2 2^1 2^0 |
0x20 0x10 0x08 0x04 0x02 0x01 |
--------------------------------------------------|
input x 0 0 x x x | 0x00
enabled x 0 0 x x x | 0x00
disabled x 1 0 x x x | 0x10
mask x 1 1 x x x | 0x18
[0] http://www.ti.com/lit/ds/symlink/am3358.pdf
[1] https://www.ti.com/lit/ug/spruh73q/spruh73q.pdf
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
[tony@atomide.com: fixed typo for am3 vs am4]
Signed-off-by: Tony Lindgren <tony@atomide.com>
for 5.9 please pull the following:
- Rafal specifies the switch ports for various Luxul devices (XAP-1410,
XAP-1510, XAP-1610, XWC-1000, XWC-2000, XWR-1200, XWR-3100, XWR-3150)
- Krzysztof fixes the L2 cache controller node name to conform to
dtschema
- Maxime introduces two new clock providers for Raspberry Pi 4, one to
support firmware based clocks and another one for the DVP block
feeding into the two HDMI blocks.
-----BEGIN PGP SIGNATURE-----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=/iqx
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.9/devicetree' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM-based SoCs Device Tree changes
for 5.9 please pull the following:
- Rafal specifies the switch ports for various Luxul devices (XAP-1410,
XAP-1510, XAP-1610, XWC-1000, XWC-2000, XWR-1200, XWR-3100, XWR-3150)
- Krzysztof fixes the L2 cache controller node name to conform to
dtschema
- Maxime introduces two new clock providers for Raspberry Pi 4, one to
support firmware based clocks and another one for the DVP block
feeding into the two HDMI blocks.
* tag 'arm-soc/for-5.9/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm: Align L2 cache-controller nodename with dtschema
ARM: dts: BCM5301X: Specify switch ports for Luxul devices
ARM: dts: bcm2711: Add HDMI DVP
ARM: dts: bcm2711: Add firmware clocks node
Link: https://lore.kernel.org/r/20200707045759.17562-1-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This series of changes configures the GPIO line names for am335x beaglebone
black and pocketbeagle to make it easier to configure the pins. To make use
of the pins, we also add the gpio-ranges for am335x.
We also enable IPU and DSP repmoteproc for am5729-beaglebone-ai, and then
there are two non-urgent dtschema validator warning fixes.
-----BEGIN PGP SIGNATURE-----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=OvXQ
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.9/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
Device tree changes for omaps for v5.9 merge window
This series of changes configures the GPIO line names for am335x beaglebone
black and pocketbeagle to make it easier to configure the pins. To make use
of the pins, we also add the gpio-ranges for am335x.
We also enable IPU and DSP repmoteproc for am5729-beaglebone-ai, and then
there are two non-urgent dtschema validator warning fixes.
* tag 'omap-for-v5.9/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-pocketbeagle: add gpio-line-names
ARM: dts: am335x-boneblack: add gpio-line-names
ARM: dts: am33xx-l4: add gpio-ranges
ARM: dts: am5729-beaglebone-ai: Disable ununsed mailboxes
ARM: dts: am5729-beaglebone-ai: Enable IPU & DSP rprocs
ARM: dts: am: Align L2 cache-controller nodename with dtschema
ARM: dts: omap: Align L2 cache-controller nodename with dtschema
Link: https://lore.kernel.org/r/pull-1594402929-762188@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- add missing interrupts property to support card serial
- fix node names to follow the DT schema
- add PCIe endpoint and PHY nodes for Pro5 SoC
- simplify device hierarchy of support-card.dtsi
-----BEGIN PGP SIGNATURE-----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=d0+s
-----END PGP SIGNATURE-----
Merge tag 'uniphier-dt-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into arm/dt
UniPhier ARM SoC DT updates for v5.9
- add missing interrupts property to support card serial
- fix node names to follow the DT schema
- add PCIe endpoint and PHY nodes for Pro5 SoC
- simplify device hierarchy of support-card.dtsi
* tag 'uniphier-dt-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
ARM: dts: uniphier: simplify support-card node structure
ARM: dts: uniphier: Add PCIe endpoint and PHY node for Pro5
ARM: dts: uniphier: Rename ethphy node to ethernet-phy
ARM: dts: uniphier: give fixed port number to support card serial
ARM: dts: uniphier: rename support card serial node to fix schema warning
ARM: dts: uniphier: add interrupts to support card serial
Link: https://lore.kernel.org/r/CAK7LNARGDcCKxV3-H7WmuZAVe49n0QF+672-KN0tsP0och0a_A@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add support for the MYiR imx6ULL based single board computer
equipped with on board 256MB NAND & RAM. The board also
provides expansion header for expansion board, but this
commit adds only support for SBC.
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is not necessary without a pinctrl-0 statement. Remove this
orphan.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The imx-pwm driver supports 3 cells and this is the more flexible setting.
So use it by default and overwrite it back to two for the files that
reference the PWMs with just 2 cells to minimize changes.
This allows to drop explicit setting to 3 cells for the boards that already
depend on this. The boards that are now using 2 cells explicitly can be
converted to 3 individually.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SFF soldered onto the board expect the ports to use 1000BaseX. It
makes no sense to have the ports set to SGMII, since they don't even
support that mode.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SFF soldered onto the board expects the port to use 1000BaseX. It
makes no sense to have the port set to SGMII, since it doesn't even
support that mode.
Signed-off-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Protonic RVT is an internal development platform for a wireless ISObus
Virtual Terminal based on COTS tablets, and the predecessor of the WD2
platform.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Protonic VT7 is a mid-class ISObus Virtual Terminal with a 7 inch
touchscreen display.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for the Protonic WD2 board, which is an internal development
platform for low-cost agricultural Virtual Terminals based on COTS tablets
and web applications.
It inherits from the PRTI6Q base class.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Protonic PRTI6Q is a development board and a base class for different
specific customer application boards based on the i.MX6 family of SoCs,
developed by Protonic Holland.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix dtschema validator warnings like:
l2-cache@a02000: $nodename:0:
'l2-cache@a02000' does not match '^(cache-controller|cpu)(@[0-9a-f,]+)*$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix dtschema validator warnings like:
l2-cache@40006000: $nodename:0:
'l2-cache@40006000' does not match '^(cache-controller|cpu)(@[0-9a-f,]+)*$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add MQS support. As the pin conflict with usdhc2, then need
to add a separate dts.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use kernel LED interface for the alarm LEDs.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Samu Nuutamo <samu.nuutamo@vincit.fi>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In imx6sll.dtsi, the ssi node name is different with other
platforms (imx6qdl, imx6sl, imx6sx), but the
sound/soc/fsl/fsl-asoc-card.c machine driver needs to check
ssi node name for audmux configuration, then different ssi
node name causes issue on imx6sll platform.
So we change ssi node name to make all platforms have same
name.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change i.MX6/i.MX7 SoCs usdhc node name from usdhc to mmc to be
compliant with yaml schema, it requires the nodename to be "mmc".
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change i.MX2/i.MX3/i.MX5 SoCs esdhc node name from esdhc to mmc to
be compliant with yaml schema, it requires the nodename to be "mmc".
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change i.MX27/i.MX31 node name from sdhci to mmc to be compliant
with yaml schema, it requires the nodename to be "mmc".
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In latest i.MX6Q RM Rev.6, 05/2020, #90 SPI interrupt is reserved,
so remove it from GPC node.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change IIM node name from iim to efuse to be compliant
with yaml schema, it requires the nodename to be one of
"eeprom|efuse|nvram".
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change OCOTP node name from ocotp to efuse to be compliant
with yaml schema, it requires the nodename to be one of
"eeprom|efuse|nvram".
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change OCOTP node name from ocotp-ctrl to efuse to be compliant with
yaml schema, it requires the nodename to be one of "eeprom|efuse|nvram".
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The timer fixed interval period pulse generator register
is used to generate periodic pulses. The down count
register loads the value programmed in the fixed period
interval (FIPER). At every tick of the timer accumulator
overflow, the counter decrements by the value of
TMR_CTRL[TCLK_PERIOD]. It generates a pulse when the down
counter value reaches zero. It reloads the down counter
in the cycle following a pulse.
To use the TMR_FIPER register to generate desired periodic
pulses. The value should programmed is,
desired_period - tclk_period
Current tmr-fiper2 value is to generate 100us periodic pulses.
(But the value should have been 99995, not 99990. The tclk_period is 5.)
This patch is to generate 1 second periodic pulses with value
999999995 programmed which is more desired by user.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX6/7 SoCs' temperature sensor is inside anatop module from HW
perspective, so it should be a child node of anatop.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The audio codec on the GW551x routes to ssi1. It fixes audio capture on
the device.
Cc: stable@vger.kernel.org
Fixes: 3117e851ce ("ARM: dts: imx: Add TDA19971 HDMI Receiver to GW551x")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This device hierarchy is needlessly complex.
Remove the support-card node level, and move the ethernet and serial
nodes right under the system-bus node.
This also fixes the following warning from 'make ARCH=arm dtbs_check':
support-card@1,1f00000: $nodename:0: 'support-card@1,1f00000' does not match '^(bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This adds PCIe endpoint controller and PHY nodes for Pro5 SoC,
and also adds pinctrl node for PCIe.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This renames the node name "ethphy" to "ethernet-phy" according to
Documentation/devicetree/bindings/net/mdio.yaml.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
As per 'struct mfd_cell ab8500_devs[]' there are not 1, but 3 PWM
devices on the AB8500. Until now, each of them have referenced
the same Device Tree node. This change ensures each device has
their own.
Due to recent `dtc` checks [0], nodes cannot share the same node
name, so we are forced to rename the affected nodes by appending
their associated numeric 'bank ID'.
[0] ste-ab8500.dtsi:210.16-214.7: ERROR (duplicate_node_names):
/soc/prcmu@80157000/ab8500/ab8500-pwm: Duplicate node name
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200622083432.1491715-1-lee.jones@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adds support for the back and menu keys on golden.
Signed-off-by: Nick Reitemeyer <nick.reitemeyer@web.de>
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200621193822.133683-2-nick.reitemeyer@web.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Increase #pinctrl-cells to 2 so that mux and conf be kept separate. This
requires the AM33XX_PADCONF macro in omap.h to also be modified to keep pin
conf and pin mux values separate.
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Link: https://lore.kernel.org/r/20200701013320.130441-3-drew@beagleboard.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since commit e69f5dc623 ("dt-bindings: serial: Convert 8250 to
json-schema"), the schema for "ns16550a" is checked.
'make ARCH=arm dtbs_check' emits the following warning:
uart@b0000: $nodename:0: 'uart@b0000' does not match '^serial(@[0-9a-f,]+)*$'
Rename the node to follow the pattern defined in
Documentation/devicetree/bindings/serial/serial.yaml
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since commit e69f5dc623 ("dt-bindings: serial: Convert 8250 to
json-schema"), the schema for "ns16550a" is checked.
Since then, 'make ARCH=arm dtbs_check' is so noisy because the
required property 'interrupts' is missing.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Remove the regulators node and define fixed regulators directly under
the root node. This makes SMDK5420 board consistent with other Exynos
boards.
Name the fixed regulator nodes consistently.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Remove the regulators node and define fixed regulators directly under
the root node. This makes Exynos5250 Arndale board consistent with
other Exynos boards.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Remove the regulators node and define fixed regulators directly under
the root node. This makes Exynos4412 Origen board consistent with other
Exynos boards.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
There is no need to keep DMA controller nodes under AMBA bus node.
Remove the "amba" node to fix dtschema warnings like:
amba: $nodename:0: 'amba' does not match '^(bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
- The first one based on the enhancements made to clk-raspberrypi, which
is now registered trough DT and provides control over the whole range
of firmware based clocks.
- The second one based on the new clk-bcm2711-dvp driver, which gates
the clocks and reset signals that feed into RPi4's HDMI0/1 blocks.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEErOkkGDHCg2EbPcGjlfZmHno8x/4FAl8DWigACgkQlfZmHno8
x/7FcggAhmCkN1I5zf7j3qDFNjIgg2sGl3JVmCasBdT8BK0yx7+5tcT3SHu9mOM0
o+8CngXUV+Tnl7LRIR0SJHtuiQkbh1MW9BAQMGrAMk+HDIzH957ki70kAp6kbLPE
EfQIrp0XCH6TXF0tpDbwpcJNQS3zpBC8cn8XgKnhVJbSnMHznP4a7iM6StvdRAov
umz65w/5QPMddvUFUVzGY1/+NVaEdqyE59xQQeoh0sbniMKuq9AlXF08kLWuyZgX
O3EJcuVgGjxS2gsVtgda74d+54fl1slkRV+T3YxYOtqe2kJcxLJx7gO4wfoM5OaC
4l2Hs3sRARSL005rUndoSMP/6uHmnw==
=+pUx
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=aAlp
-----END PGP SIGNATURE-----
Merge tag 'tags/bcm2835-dt-next-2020-07-06' into devicetree/next
Maxime Ripard introduces two new clock providers into RPi4's device tree:
- The first one based on the enhancements made to clk-raspberrypi, which
is now registered trough DT and provides control over the whole range
of firmware based clocks.
- The second one based on the new clk-bcm2711-dvp driver, which gates
the clocks and reset signals that feed into RPi4's HDMI0/1 blocks.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fix dtschema validator warnings like:
l2-cache@22000: $nodename:0:
'l2-cache@22000' does not match '^(cache-controller|cpu)(@[0-9a-f,]+)*$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
All those devices use standard BCM53011 (rev 5) or BCM53012 (rev 0).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The hardware codec on the A10, A10s, A13 and A20 needs buffer in the
first 256MB of RAM. This was solved by setting the CMA pool at a fixed
address in that range.
However, in recent kernels there's something else that comes in and
reserve some range that end up conflicting with our default pool
requirement, and thus makes its reservation fail.
The video codec will then use buffers from the usual default pool,
outside of the range it can access, and will fail to decode anything.
Since we're only concerned about that 256MB, we can however relax the
allocation to just specify the range that's allowed, and not try to
enforce a specific address.
Fixes: 5949bc5602 ("ARM: dts: sun4i-a10: Add Video Engine and reserved memory nodes")
Fixes: 9604320101 ("ARM: dts: sun5i: Add Video Engine and reserved memory nodes")
Fixes: c2a641a748 ("ARM: dts: sun7i-a20: Add Video Engine and reserved memory nodes")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20200704130829.34297-1-maxime@cerno.tech
Remove the regulators node entirely because its children do not have any
unit addresses. This fixes DTC warning:
Warning (simple_bus_reg): /regulators/regulator-0: missing or empty reg/ranges property
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Audio Graph Card is using "audio-graph-card" prefix instead of
"simple-graph-card", and moreover "widgets / routing" doesn't need it.
This patch removes unsupported "simple-graph-card" prefix from
motorola-mapphone-common.dtsi and vendor-prefixes.yaml.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/87r1ub39hq.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead, expose the key via the input framework, as SW_MACHINE_COVER
The chip-detect GPIO is actually detecting if the cover is closed.
Technically it's possible to use the SD card with open cover. The
only downside is risk of battery falling out and user being able
to physically remove the card.
The behaviour of SD card not being available when the device is
open is unexpected and creates more problems than it solves. There
is a high chance, that more people accidentally break their rootfs
by opening the case without physically removing the card.
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Merlijn Wajer <merlijn@wizzup.org>
Link: https://lore.kernel.org/r/20200612125402.18393-3-merlijn@wizzup.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fix dtschema validator warnings like:
l2-cache-controller@c4200000: $nodename:0:
'l2-cache-controller@c4200000' does not match '^(cache-controller|cpu)(@[0-9a-f,]+)*$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20200626080626.4080-1-krzk@kernel.org
The BeagleBoard.org PocketBeagle has P1 and P2 headers [0] which expose
many of the TI AM3358 SoC balls to stacking expansion boards called
"capes", or to other external connections like jumper wires connected
to a breadboard.
Note: the AM3358 die is actually embedded inside of the OSD335x-SM
System-in-Package (SiP) [1] but that is irrelevant to the gpio driver.
Many of the P1 and P2 header pins can muxed to a GPIO line. The
gpio-line-names describe which P1 or P2 pin that line goes to and the
default mux for that P1 or P2 pin if it is not GPIO.
Some GPIO lines are named "[NC]" as the corresponding balls are not
routed to anything on the PCB.
The goal for these names is to make it easier for a user viewing the
output of gpioinfo to determine which P1 or P2 pin is connected to a
GPIO line. The output of gpioinfo on a PocketBeagle would be:
gpiochip0 - 32 lines:
line 0: "[NC]" unused input active-high
line 1: "[NC]" unused input active-high
line 2: "P1.08 [SPI0_CLK]" unused input active-high
line 3: "P1.10 [SPI0_MISO]" unused input active-high
line 4: "P1.12 [SPI0_MOSI]" unused input active-high
line 5: "P1.06 [SPI0_CS]" unused input active-high
line 6: "[MMC0_CD]" "cd" input active-low [used]
line 7: "P2.29 [SPI1_CLK]" unused input active-high
line 8: "[SYSBOOT]" unused input active-high
line 9: "[SYSBOOT]" unused input active-high
line 10: "[SYSBOOT]" unused input active-high
line 11: "[SYSBOOT]" unused input active-high
line 12: "P1.26 [I2C2_SDA]" unused input active-high
line 13: "P1.28 [I2C2_SCL]" unused input active-high
line 14: "P2.11 [I2C1_SDA]" unused input active-high
line 15: "P2.09 [I2C1_SCL]" unused input active-high
line 16: "[NC]" unused input active-high
line 17: "[NC]" unused input active-high
line 18: "[NC]" unused input active-high
line 19: "P2.31 [SPI1_CS]" unused input active-high
line 20: "P1.20 [PRU0.16]" unused input active-high
line 21: "[NC]" unused input active-high
line 22: "[NC]" unused input active-high
line 23: "P2.03" unused input active-high
line 24: "[NC]" unused input active-high
line 25: "[NC]" unused input active-high
line 26: "P1.34" unused input active-high
line 27: "P2.19" unused input active-high
line 28: "[NC]" unused input active-high
line 29: "[NC]" unused input active-high
line 30: "P2.05 [UART4_RX]" unused input active-high
line 31: "P2.07 [UART4_TX]" unused input active-high
gpiochip1 - 32 lines:
line 0: "[NC]" unused input active-high
line 1: "[NC]" unused input active-high
line 2: "[NC]" unused input active-high
line 3: "[NC]" unused input active-high
line 4: "[NC]" unused input active-high
line 5: "[NC]" unused input active-high
line 6: "[NC]" unused input active-high
line 7: "[NC]" unused input active-high
line 8: "[NC]" unused input active-high
line 9: "P2.25 [SPI1_MOSI]" unused input active-high
line 10: "P1.32 [UART0_RX]" unused input active-high
line 11: "P1.30 [UART0_TX]" unused input active-high
line 12: "P2.24" unused input active-high
line 13: "P2.33" unused input active-high
line 14: "P2.22" unused input active-high
line 15: "P2.18" unused input active-high
line 16: "[NC]" unused input active-high
line 17: "[NC]" unused input active-high
line 18: "P2.01 [PWM1A]" unused input active-high
line 19: "[NC]" unused input active-high
line 20: "P2.10" unused input active-high
line 21: "[USR LED 0]" "beaglebone:green:usr0" output active-high [used]
line 22: "[USR LED 1]" "beaglebone:green:usr1" output active-high [used]
line 23: "[USR LED 2]" "beaglebone:green:usr2" output active-high [used]
line 24: "[USR LED 3]" "beaglebone:green:usr3" output active-high [used]
line 25: "P2.06" unused input active-high
line 26: "P2.04" unused input active-high
line 27: "P2.02" unused input active-high
line 28: "P2.08" unused input active-high
line 29: "[NC]" unused input active-high
line 30: "[NC]" unused input active-high
line 31: "[NC]" unused input active-high
gpiochip2 - 32 lines:
line 0: "P2.20" unused input active-high
line 1: "P2.17" unused input active-high
line 2: "[NC]" unused input active-high
line 3: "[NC]" unused input active-high
line 4: "[NC]" unused input active-high
line 5: "[EEPROM_WP]" unused input active-high
line 6: "[SYSBOOT]" unused input active-high
line 7: "[SYSBOOT]" unused input active-high
line 8: "[SYSBOOT]" unused input active-high
line 9: "[SYSBOOT]" unused input active-high
line 10: "[SYSBOOT]" unused input active-high
line 11: "[SYSBOOT]" unused input active-high
line 12: "[SYSBOOT]" unused input active-high
line 13: "[SYSBOOT]" unused input active-high
line 14: "[SYSBOOT]" unused input active-high
line 15: "[SYSBOOT]" unused input active-high
line 16: "[SYSBOOT]" unused input active-high
line 17: "[SYSBOOT]" unused input active-high
line 18: "[NC]" unused input active-high
line 19: "[NC]" unused input active-high
line 20: "[NC]" unused input active-high
line 21: "[NC]" unused input active-high
line 22: "P2.35 [AIN5]" unused input active-high
line 23: "P1.02 [AIN6]" unused input active-high
line 24: "P1.35 [PRU1.10]" unused input active-high
line 25: "P1.04 [PRU1.11]" unused input active-high
line 26: "[MMC0_DAT3]" unused input active-high
line 27: "[MMC0_DAT2]" unused input active-high
line 28: "[MMC0_DAT1]" unused input active-high
line 29: "[MMC0_DAT0]" unused input active-high
line 30: "[MMC0_CLK]" unused input active-high
line 31: "[MMC0_CMD]" unused input active-high
gpiochip3 - 32 lines:
line 0: "[NC]" unused input active-high
line 1: "[NC]" unused input active-high
line 2: "[NC]" unused input active-high
line 3: "[NC]" unused input active-high
line 4: "[NC]" unused input active-high
line 5: "[I2C0_SDA]" unused input active-high
line 6: "[I2C0_SCL]" unused input active-high
line 7: "[JTAG]" unused input active-high
line 8: "[JTAG]" unused input active-high
line 9: "[NC]" unused input active-high
line 10: "[NC]" unused input active-high
line 11: "[NC]" unused input active-high
line 12: "[NC]" unused input active-high
line 13: "P1.03 [USB1]" unused input active-high
line 14: "P1.36 [PWM0A]" unused input active-high
line 15: "P1.33 [PRU0.1]" unused input active-high
line 16: "P2.32 [PRU0.2]" unused input active-high
line 17: "P2.30 [PRU0.3]" unused input active-high
line 18: "P1.31 [PRU0.4]" unused input active-high
line 19: "P2.34 [PRU0.5]" unused input active-high
line 20: "P2.28 [PRU0.6]" unused input active-high
line 21: "P1.29 [PRU0.7]" unused input active-high
line 22: "[NC]" unused input active-high
line 23: "[NC]" unused input active-high
line 24: "[NC]" unused input active-high
line 25: "[NC]" unused input active-high
line 26: "[NC]" unused input active-high
line 27: "[NC]" unused input active-high
line 28: "[NC]" unused input active-high
line 29: "[NC]" unused input active-high
line 30: "[NC]" unused input active-high
line 31: "[NC]" unused input active-high
[0] https://github.com/beagleboard/pocketbeagle/wiki/System-Reference-Manual#71_Expansion_Header_Connectors
[1] https://octavosystems.com/app_notes/osd335x-family-pin-assignments/
Reviewed-by: Jason Kridner <jason@beagleboard.org>
Reviewed-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The BeagleBone Black has P8 and P9 headers [0] which expose many of the
AM3358 ZCZ SoC balls to stacking expansion boards called "capes", or to
other external connections like jumper wires connected to a breadboard.
BeagleBone users will often refer to the "Cape Exanpsion Headers" pin
diagram [1] as it is in the "Bone101" getting started tutorial. [2]
Most of the P8 and P9 header pins can muxed to a GPIO line. The
gpio-line-names describe which P8 or P9 pin that line goes to and the
default mux for that P8 or P9 pin if it is not GPIO.
For example, gpiochip 1 line 0 is connected to P8 header pin 25 (P8_25)
however the default device tree has the corresponding BGA ball (ZCZ U7)
muxed to mmc1_dat0 as it is used for the on-board eMMC chip. For that
GPIO line to be used, one would need to modify the device tree to
disable the eMMC and change the pin mux for that ball to GPIO mode.
Some of the AM3358 ZCZ balls corresponding to GPIO lines are not routed
to a P8 or P9 header, but are instead wired to some peripheral device
like on-board eMMC, HDMI framer IC, or status LEDs. Those names are in
brackets to denote those GPIO lines can not be used.
Some GPIO lines are named "[NC]" as the corresponding balls are not
routed to anything on the PCB.
The goal for these names is to make it easier for a user viewing the
output of gpioinfo to determine which P8 or P9 pin is connected to a
GPIO line. The output of gpioinfo on a BeagleBone Black would be:
gpiochip0 - 32 lines:
line 0: "[ethernet]" unused input active-high
line 1: "[ethernet]" unused input active-high
line 2: "P9_22 [spi0_sclk]" unused input active-high
line 3: "P9_21 [spi0_d0]" unused input active-high
line 4: "P9_18 [spi0_d1]" unused input active-high
line 5: "P9_17 [spi0_cs0]" unused input active-high
line 6: "[sd card]" "cd" input active-low [used]
line 7: "P9_42A [ecappwm0]" unused input active-high
line 8: "P8_35 [hdmi]" unused input active-high
line 9: "P8_33 [hdmi]" unused input active-high
line 10: "P8_31 [hdmi]" unused input active-high
line 11: "P8_32 [hdmi]" unused input active-high
line 12: "P9_20 [i2c2_sda]" unused input active-high
line 13: "P9_19 [i2c2_scl]" unused input active-high
line 14: "P9_26 [uart1_rxd]" unused input active-high
line 15: "P9_24 [uart1_txd]" unused input active-high
line 16: "[ethernet]" unused input active-high
line 17: "[ethernet]" unused input active-high
line 18: "[usb]" unused input active-high
line 19: "[hdmi]" unused input active-high
line 20: "P9_41B" unused input active-high
line 21: "[ethernet]" unused input active-high
line 22: "P8_19 [ehrpwm2a]" unused input active-high
line 23: "P8_13 [ehrpwm2b]" unused input active-high
line 24: "[NC]" unused input active-high
line 25: "[NC]" unused input active-high
line 26: "P8_14" unused input active-high
line 27: "P8_17" unused input active-high
line 28: "[ethernet]" unused input active-high
line 29: "[ethernet]" unused input active-high
line 30: "P9_11 [uart4_rxd]" unused input active-high
line 31: "P9_13 [uart4_txd]" unused input active-high
gpiochip1 - 32 lines:
line 0: "P8_25 [emmc]" unused input active-high
line 1: "[emmc]" unused input active-high
line 2: "P8_5 [emmc]" unused input active-high
line 3: "P8_6 [emmc]" unused input active-high
line 4: "P8_23 [emmc]" unused input active-high
line 5: "P8_22 [emmc]" unused input active-high
line 6: "P8_3 [emmc]" unused input active-high
line 7: "P8_4 [emmc]" unused input active-high
line 8: "[NC]" unused input active-high
line 9: "[NC]" unused input active-high
line 10: "[NC]" unused input active-high
line 11: "[NC]" unused input active-high
line 12: "P8_12" unused input active-high
line 13: "P8_11" unused input active-high
line 14: "P8_16" unused input active-high
line 15: "P8_15" unused input active-high
line 16: "P9_15A" unused input active-high
line 17: "P9_23" unused input active-high
line 18: "P9_14 [ehrpwm1a]" unused input active-high
line 19: "P9_16 [ehrpwm1b]" unused input active-high
line 20: "[emmc]" unused input active-high
line 21: "[usr0 led]" "beaglebone:green:heartbeat" output active-high [used]
line 22: "[usr1 led]" "beaglebone:green:mmc0" output active-high [used]
line 23: "[usr2 led]" "beaglebone:green:usr2" output active-high [used]
line 24: "[usr3 led]" "beaglebone:green:usr3" output active-high [used]
line 25: "[hdmi]" "interrupt" input active-high [used]
line 26: "[usb]" unused input active-high
line 27: "[hdmi audio]" "enable" output active-high [used]
line 28: "P9_12" unused input active-high
line 29: "P8_26" unused input active-high
line 30: "P8_21 [emmc]" unused input active-high
line 31: "P8_20 [emmc]" unused input active-high
gpiochip2 - 32 lines:
line 0: "P9_15B" unused input active-high
line 1: "P8_18" unused input active-high
line 2: "P8_7" unused input active-high
line 3: "P8_8" unused input active-high
line 4: "P8_10" unused input active-high
line 5: "P8_9" unused input active-high
line 6: "P8_45 [hdmi]" unused input active-high
line 7: "P8_46 [hdmi]" unused input active-high
line 8: "P8_43 [hdmi]" unused input active-high
line 9: "P8_44 [hdmi]" unused input active-high
line 10: "P8_41 [hdmi]" unused input active-high
line 11: "P8_42 [hdmi]" unused input active-high
line 12: "P8_39 [hdmi]" unused input active-high
line 13: "P8_40 [hdmi]" unused input active-high
line 14: "P8_37 [hdmi]" unused input active-high
line 15: "P8_38 [hdmi]" unused input active-high
line 16: "P8_36 [hdmi]" unused input active-high
line 17: "P8_34 [hdmi]" unused input active-high
line 18: "[ethernet]" unused input active-high
line 19: "[ethernet]" unused input active-high
line 20: "[ethernet]" unused input active-high
line 21: "[ethernet]" unused input active-high
line 22: "P8_27 [hdmi]" unused input active-high
line 23: "P8_29 [hdmi]" unused input active-high
line 24: "P8_28 [hdmi]" unused input active-high
line 25: "P8_30 [hdmi]" unused input active-high
line 26: "[emmc]" unused input active-high
line 27: "[emmc]" unused input active-high
line 28: "[emmc]" unused input active-high
line 29: "[emmc]" unused input active-high
line 30: "[emmc]" unused input active-high
line 31: "[emmc]" unused input active-high
gpiochip3 - 32 lines:
line 0: "[ethernet]" unused input active-high
line 1: "[ethernet]" unused input active-high
line 2: "[ethernet]" unused input active-high
line 3: "[ethernet]" unused input active-high
line 4: "[ethernet]" unused input active-high
line 5: "[i2c0]" unused input active-high
line 6: "[i2c0]" unused input active-high
line 7: "[emu]" unused input active-high
line 8: "[emu]" unused input active-high
line 9: "[ethernet]" unused input active-high
line 10: "[ethernet]" unused input active-high
line 11: "[NC]" unused input active-high
line 12: "[NC]" unused input active-high
line 13: "[usb]" unused input active-high
line 14: "P9_31 [spi1_sclk]" unused input active-high
line 15: "P9_29 [spi1_d0]" unused input active-high
line 16: "P9_30 [spi1_d1]" unused input active-high
line 17: "P9_28 [spi1_cs0]" unused input active-high
line 18: "P9_42B [ecappwm0]" unused input active-high
line 19: "P9_27" unused input active-high
line 20: "P9_41A" unused input active-high
line 21: "P9_25" unused input active-high
line 22: "[NC]" unused input active-high
line 23: "[NC]" unused input active-high
line 24: "[NC]" unused input active-high
line 25: "[NC]" unused input active-high
line 26: "[NC]" unused input active-high
line 27: "[NC]" unused input active-high
line 28: "[NC]" unused input active-high
line 29: "[NC]" unused input active-high
line 30: "[NC]" unused input active-high
line 31: "[NC]" unused input active-high
[0] https://git.io/JfgOd
[1] https://beagleboard.org/capes
[1] https://beagleboard.org/Support/bone101
[2] https://beagleboard.org/static/images/cape-headers.png
Reviewed-by: Jason Kridner <jason@beagleboard.org>
Reviewed-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add gpio-ranges properties to the gpio controller nodes.
These gpio-ranges were created based on "Table 9-10. CONTROL_MODULE
REGISTERS" in the "AM335x Technical Reference Manual" [0] and "Table
4-2. Pin Attributes" in the "AM335x Sitara Processor datasheet" [1].
A csv file with this data is available for reference [2].
These mappings are valid for all SoC's that are using am33xx-l4.dtsi.
In addition, the only TI AM33xx parts that actually exist are [0]:
AM3351, AM3352, AM3354, AM3356, AM3357, AM3358, AM3359
These gpio-ranges properties should be added as they describe the
relationship between a gpio line and pin control register that exists
in the hardware. For example, GPMC_A0 pin has mode 7 which is labeled
gpio1_16. conf_gpmc_a0 register is at offset 840h which makes it pin 16.
[0] https://www.ti.com/lit/ug/spruh73q/spruh73q.pdf
[1] http://www.ti.com/lit/ds/symlink/am3358.pdf
[2] https://gist.github.com/pdp7/6ffaddc8867973c1c3e8612cfaf72020
[3] http://www.ti.com/processors/sitara-arm/am335x-cortex-a8/overview.html
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IPU and DSP remote processors use sub-mailbox nodes only from a
limited set of System Mailboxes 5 and 6 to achieve the Remote Processor
Messaging (RPMsg) communication stack between the MPU host processor
and the respective remote processor. These are all defined and enabled
through the inherited common dra74-ipu-dsp-common.dtsi file.
The other System Mailboxes do not define any actual sub-mailboxes, so
they serve no purpose and can all be safely dropped.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Assign the previously added CMA reserved memory nodes to the respective
IPU and DSP rproc device nodes, and enable these rproc nodes so that
these remote processors can be booted on the AM5729 BeagleBone AI board.
The addresses and sizes of the CMA pools are identical to those used on
various other TI AM572x/AM574x based boards. The mailboxes, timers and
watchdog-timers for all these remoteprocs are inherited by including the
common dra72-ipu-dsp-common.dtsi file.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix dtschema validator warnings like:
l2-cache-controller@48242000: $nodename:0: 'l2-cache-controller@48242000'
does not match '^(cache-controller|cpu)(@[0-9a-f,]+)*$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix dtschema validator warnings like:
l2-cache-controller@48242000: $nodename:0:
'l2-cache-controller@48242000' does not match '^(cache-controller|cpu)(@[0-9a-f,]+)*$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Various OMAP3 boards have two AES blocks, but only one is currently
available, because the hwmods are only configured for one.
This patch migrates the hwmods for the AES engine to sysc-omap2
which allows the second AES crypto engine to become available.
omap-aes 480a6000.aes1: OMAP AES hw accel rev: 2.6
omap-aes 480a6000.aes1: will run requests pump with realtime priority
omap-aes 480c5000.aes2: OMAP AES hw accel rev: 2.6
omap-aes 480c5000.aes2: will run requests pump with realtime priority
Signed-off-by: Adam Ford <aford173@gmail.com>
[tony@atomide.com: updated to disable both aes_targets on hs boards]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP developers are particularly active at hunting down regressions,
so this is a separate branch with OMAP specific fixes for the v5.8:
As Tony explains
"The recent display subsystem (DSS) related platform data changes
caused display related regressions for suspend and resume. Looks like
I only tested suspend and resume before dropping the legacy platform
data, and forgot to test it after dropping it. Turns out the main issue
was that we no longer have platform code calling pm_runtime_suspend
for DSS like we did for the legacy platform data case, and that fix
is still being discussed on the dri-devel list and will get merged
separately. The DSS related testing exposed a pile other other display
related issues that also need fixing though":
- Fix ti-sysc optional clock handling and reset status checks
for devices that reset automatically in idle like DSS
- Ignore ti-sysc clockactivity bit unless separately requested
to avoid unexpected performance issues
- Init ti-sysc framedonetv_irq to true and disable for am4
- Avoid duplicate DSS reset for legacy mode with dts data
- Remove LCD timings for am4 as they cause warnings now that we're
using generic panels
Other OMAP changes from Tony include:
- Fix omap_prm reset deassert as we still have drivers setting the
pm_runtime_irq_safe() flag
- Flush posted write for ti-sysc enable and disable
- Fix droid4 spi related errors with spi flags
- Fix am335x USB range and a typo for softreset
- Fix dra7 timer nodes for clocks for IPU and DSP
- Drop duplicate mailboxes after mismerge for dra7
- Prevent pocketgeagle header line signal from accidentally setting
micro-SD write protection signal by removing the default mux
- Fix NFSroot flakeyness after resume for duover by switching the
smsc911x gpio interrupt to back to level sensitive
- Fix regression for omap4 clockevent source after recent system
timer changes
- Yet another ethernet regression fix for the "rgmii" vs "rgmii-rxid"
phy-mode
- One patch to convert am3/am4 DT files to use the regular sdhci-omap
driver instead of the old hsmmc driver, this was meant for the
merge window but got lost in the process.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=FFTv
-----END PGP SIGNATURE-----
Merge tag 'arm-omap-fixes-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM OMAP fixes from Arnd Bergmann:
"The OMAP developers are particularly active at hunting down
regressions, so this is a separate branch with OMAP specific
fixes for v5.8:
As Tony explains
"The recent display subsystem (DSS) related platform data changes
caused display related regressions for suspend and resume. Looks
like I only tested suspend and resume before dropping the legacy
platform data, and forgot to test it after dropping it. Turns out
the main issue was that we no longer have platform code calling
pm_runtime_suspend for DSS like we did for the legacy platform data
case, and that fix is still being discussed on the dri-devel list
and will get merged separately. The DSS related testing exposed a
pile other other display related issues that also need fixing
though":
- Fix ti-sysc optional clock handling and reset status checks for
devices that reset automatically in idle like DSS
- Ignore ti-sysc clockactivity bit unless separately requested to
avoid unexpected performance issues
- Init ti-sysc framedonetv_irq to true and disable for am4
- Avoid duplicate DSS reset for legacy mode with dts data
- Remove LCD timings for am4 as they cause warnings now that we're
using generic panels
Other OMAP changes from Tony include:
- Fix omap_prm reset deassert as we still have drivers setting the
pm_runtime_irq_safe() flag
- Flush posted write for ti-sysc enable and disable
- Fix droid4 spi related errors with spi flags
- Fix am335x USB range and a typo for softreset
- Fix dra7 timer nodes for clocks for IPU and DSP
- Drop duplicate mailboxes after mismerge for dra7
- Prevent pocketgeagle header line signal from accidentally setting
micro-SD write protection signal by removing the default mux
- Fix NFSroot flakeyness after resume for duover by switching the
smsc911x gpio interrupt to back to level sensitive
- Fix regression for omap4 clockevent source after recent system
timer changes
- Yet another ethernet regression fix for the "rgmii" vs "rgmii-rxid"
phy-mode
- One patch to convert am3/am4 DT files to use the regular sdhci-omap
driver instead of the old hsmmc driver, this was meant for the
merge window but got lost in the process"
* tag 'arm-omap-fixes-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (21 commits)
ARM: dts: am5729: beaglebone-ai: fix rgmii phy-mode
ARM: dts: Fix omap4 system timer source clocks
ARM: dts: Fix duovero smsc interrupt for suspend
ARM: dts: am335x-pocketbeagle: Fix mmc0 Write Protect
Revert "bus: ti-sysc: Increase max softreset wait"
ARM: dts: am437x-epos-evm: remove lcd timings
ARM: dts: am437x-gp-evm: remove lcd timings
ARM: dts: am437x-sk-evm: remove lcd timings
ARM: dts: dra7-evm-common: Fix duplicate mailbox nodes
ARM: dts: dra7: Fix timer nodes properly for timer_sys_ck clocks
ARM: dts: Fix am33xx.dtsi ti,sysc-mask wrong softreset flag
ARM: dts: Fix am33xx.dtsi USB ranges length
bus: ti-sysc: Increase max softreset wait
ARM: OMAP2+: Fix legacy mode dss_reset
bus: ti-sysc: Fix uninitialized framedonetv_irq
bus: ti-sysc: Ignore clockactivity unless specified as a quirk
bus: ti-sysc: Use optional clocks on for enable and wait for softreset bit
ARM: dts: omap4-droid4: Fix spi configuration and increase rate
bus: ti-sysc: Flush posted write on enable and disable
soc: ti: omap-prm: use atomic iopoll instead of sleeping one
...
- Fix LDO1 and LDO2 voltage range for a couple of i.MX8M board device
trees.
- Fix i.MX8MP UID fuse offset in i.MX8M SoC driver.
- Fix watchdog configuration in imx6ul-kontron device tree.
- Fix one build warning seen on building soc-imx8m driver with
x86_64-randconfig.
- Add missing put_device() call for a couple of mach-imx PM functions.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl7zM08UHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM5HNAf+Kw6EPNxYom/MJ4P92gxLAtPA6AO4
+WuLYmSphhgmGAQLFU4UiTH/2sYXmT7fSDwLhfZI5XJp6j8J89Hxe2kyMomvIT92
Xbbzp7fr+2FPGgyI6ImiKTFeSZiT0LPq5fs1uF2lTP6+/SklF9yy5ynUvNULrD4b
iSAXOZkMz6Ft8dn1zYrTKPIYfsTe1zXsDgw8a9sc+0LfgiR5cBTq359jHrN5Q0Tq
NYoOHT+8V5C8BVmzp5I1zoghZEayPT2Ui1JIwBiyVij8KqZvYY3wckjPqgdfQ1vK
IzGksPWRojKAw2RKA59kpUR/pgoZH3GYnfjmCAIOkMnMSgAqz1inZZq2oA==
=iERQ
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.8:
- Fix LDO1 and LDO2 voltage range for a couple of i.MX8M board device
trees.
- Fix i.MX8MP UID fuse offset in i.MX8M SoC driver.
- Fix watchdog configuration in imx6ul-kontron device tree.
- Fix one build warning seen on building soc-imx8m driver with
x86_64-randconfig.
- Add missing put_device() call for a couple of mach-imx PM functions.
* tag 'imx-fixes-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx8m: fix build warning
ARM: imx6: add missing put_device() call in imx6q_suspend_init()
ARM: imx5: add missing put_device() call in imx_suspend_alloc_ocram()
soc: imx8m: Correct i.MX8MP UID fuse offset
ARM: dts: imx6ul-kontron: Change WDOG_ANY signal from push-pull to open-drain
ARM: dts: imx6ul-kontron: Move watchdog from Kontron i.MX6UL/ULL board to SoM
arm64: dts: imx8mm-beacon: Fix voltages on LDO1 and LDO2
arm64: dts: imx8mn-ddr4-evk: correct ldo1/ldo2 voltage range
arm64: dts: imx8mm-evk: correct ldo1/ldo2 voltage range
Link: https://lore.kernel.org/r/20200624111725.GA24312@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
5.8, please pull the following:
- Rafal adds a missing 'device_type' property to the Luxul XWC-2000
required for the memory nodes to be correctly parsed by Linux
- Matthew provides two fixes for the NSP SoCs, one to disable the PL330
DMA controller by default since it can be left in reset by the
bootloader and the second to correct the flow accelerator mailbox node
-----BEGIN PGP SIGNATURE-----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=SUaO
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.8/devicetree-fixes' of https://github.com/Broadcom/stblinux into arm/fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
5.8, please pull the following:
- Rafal adds a missing 'device_type' property to the Luxul XWC-2000
required for the memory nodes to be correctly parsed by Linux
- Matthew provides two fixes for the NSP SoCs, one to disable the PL330
DMA controller by default since it can be left in reset by the
bootloader and the second to correct the flow accelerator mailbox node
* tag 'arm-soc/for-5.8/devicetree-fixes' of https://github.com/Broadcom/stblinux:
ARM: dts: NSP: Correct FA2 mailbox node
ARM: dts: NSP: Disable PL330 by default, add dma-coherent property
ARM: dts: BCM5301X: Add missing memory "device_type" for Luxul XWC-2000
Link: https://lore.kernel.org/r/20200619202250.19029-1-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Few fixes for various devices:
- Prevent pocketgeagle header line signal from accidentally setting
micro-SD write protection signal by removing the default mux
- Fix NFSroot flakeyness after resume for duover by switching the
smsc911x gpio interrupt to back to level sensitive
- Fix regression for omap4 clockevent source after recent system
timer changes
- Yet another ethernet regression fix for the "rgmii" vs "rgmii-rxid"
phy-mode
-----BEGIN PGP SIGNATURE-----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=Hqfw
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.8/fixes-rc1-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/omap-fixes
Few dts fixes for omaps for v5.8
Few fixes for various devices:
- Prevent pocketgeagle header line signal from accidentally setting
micro-SD write protection signal by removing the default mux
- Fix NFSroot flakeyness after resume for duover by switching the
smsc911x gpio interrupt to back to level sensitive
- Fix regression for omap4 clockevent source after recent system
timer changes
- Yet another ethernet regression fix for the "rgmii" vs "rgmii-rxid"
phy-mode
* tag 'omap-for-v5.8/fixes-rc1-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am5729: beaglebone-ai: fix rgmii phy-mode
ARM: dts: Fix omap4 system timer source clocks
ARM: dts: Fix duovero smsc interrupt for suspend
ARM: dts: am335x-pocketbeagle: Fix mmc0 Write Protect
Link: https://lore.kernel.org/r/pull-1592499282-121092@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
I forgot to send a pull request earlier for converting am3 and am4 to
use sdhci-omap driver instead of the old omap_hsmmc driver.
There was a display subsystem related suspend and resume regression found
recently and looks like I forgot to send a pull request for this patch
while debugging the regression. This patch has been tested without the
display subsystem, and has been in Linux next for several weeks now, so
would be good to have merged for v5.8.
-----BEGIN PGP SIGNATURE-----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=UNki
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.8/dt-missed-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/omap-fixes
Missed sdhci patch for am3 and am4
I forgot to send a pull request earlier for converting am3 and am4 to
use sdhci-omap driver instead of the old omap_hsmmc driver.
There was a display subsystem related suspend and resume regression found
recently and looks like I forgot to send a pull request for this patch
while debugging the regression. This patch has been tested without the
display subsystem, and has been in Linux next for several weeks now, so
would be good to have merged for v5.8.
* tag 'omap-for-v5.8/dt-missed-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Move am33xx and am43xx mmc nodes to sdhci-omap driver
Link: https://lore.kernel.org/r/pull-1591637467-607254@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The recent display subsystem (DSS) related platform data changes caused
display related regressions for suspend and resume. Looks like I only
tested suspend and resume before dropping the legacy platform data, and
forgot to test it after dropping it. Turns out the main issue was that
we no longer have platform code calling pm_runtime_suspend for DSS like
we did for the legacy platform data case, and that fix is still being
discussed on the dri-devel list and will get merged separately. The DSS
related testing exposed a pile other other display related issues that
also need fixing though:
- Fix ti-sysc optional clock handling and reset status checks
for devices that reset automatically in idle like DSS
- Ignore ti-sysc clockactivity bit unless separately requested
to avoid unexpected performance issues
- Init ti-sysc framedonetv_irq to true and disable for am4
- Avoid duplicate DSS reset for legacy mode with dts data
- Remove LCD timings for am4 as they cause warnings now that we're
using generic panels
Then there is a pile of other fixes not related to the DSS:
- Fix omap_prm reset deassert as we still have drivers setting the
pm_runtime_irq_safe() flag
- Flush posted write for ti-sysc enable and disable
- Fix droid4 spi related errors with spi flags
- Fix am335x USB range and a typo for softreset
- Fix dra7 timer nodes for clocks for IPU and DSP
- Drop duplicate mailboxes after mismerge for dra7
-----BEGIN PGP SIGNATURE-----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=fT9A
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.8/fixes-merge-window-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for v5.8
The recent display subsystem (DSS) related platform data changes caused
display related regressions for suspend and resume. Looks like I only
tested suspend and resume before dropping the legacy platform data, and
forgot to test it after dropping it. Turns out the main issue was that
we no longer have platform code calling pm_runtime_suspend for DSS like
we did for the legacy platform data case, and that fix is still being
discussed on the dri-devel list and will get merged separately. The DSS
related testing exposed a pile other other display related issues that
also need fixing though:
- Fix ti-sysc optional clock handling and reset status checks
for devices that reset automatically in idle like DSS
- Ignore ti-sysc clockactivity bit unless separately requested
to avoid unexpected performance issues
- Init ti-sysc framedonetv_irq to true and disable for am4
- Avoid duplicate DSS reset for legacy mode with dts data
- Remove LCD timings for am4 as they cause warnings now that we're
using generic panels
Then there is a pile of other fixes not related to the DSS:
- Fix omap_prm reset deassert as we still have drivers setting the
pm_runtime_irq_safe() flag
- Flush posted write for ti-sysc enable and disable
- Fix droid4 spi related errors with spi flags
- Fix am335x USB range and a typo for softreset
- Fix dra7 timer nodes for clocks for IPU and DSP
- Drop duplicate mailboxes after mismerge for dra7
* tag 'omap-for-v5.8/fixes-merge-window-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
Revert "bus: ti-sysc: Increase max softreset wait"
ARM: dts: am437x-epos-evm: remove lcd timings
ARM: dts: am437x-gp-evm: remove lcd timings
ARM: dts: am437x-sk-evm: remove lcd timings
ARM: dts: dra7-evm-common: Fix duplicate mailbox nodes
ARM: dts: dra7: Fix timer nodes properly for timer_sys_ck clocks
ARM: dts: Fix am33xx.dtsi ti,sysc-mask wrong softreset flag
ARM: dts: Fix am33xx.dtsi USB ranges length
bus: ti-sysc: Increase max softreset wait
ARM: OMAP2+: Fix legacy mode dss_reset
bus: ti-sysc: Fix uninitialized framedonetv_irq
bus: ti-sysc: Ignore clockactivity unless specified as a quirk
bus: ti-sysc: Use optional clocks on for enable and wait for softreset bit
ARM: dts: omap4-droid4: Fix spi configuration and increase rate
bus: ti-sysc: Flush posted write on enable and disable
soc: ti: omap-prm: use atomic iopoll instead of sleeping one
Link: https://lore.kernel.org/r/pull-1591889257-410830@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Partial revert of some recent fixes to silence DTC warning which broke
clocks on some Vexpress platforms resulting in boot issues.
-----BEGIN PGP SIGNATURE-----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=2f3w
-----END PGP SIGNATURE-----
Merge tag 'juno-fix-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/fixes
ARMv8 Juno/Vexpress/Fast Models fix for v5.8
Partial revert of some recent fixes to silence DTC warning which broke
clocks on some Vexpress platforms resulting in boot issues.
* tag 'juno-fix-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm: dts: vexpress: Move mcc node back into motherboard node
Link: https://lore.kernel.org/r/20200609180447.GB5732@bogus
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The PDMIC needs PDM microphones to work. sama5d2 xplained doesn't have
such microphones, so there is no reason to enable PDMIC and take the
pins since there is no-one using them.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200618152845.682723-1-codrin.ciubotariu@microchip.com
Fix dtschema warning message by changing nodename to 'cache-controller':
DT_SCHEMA_FILES=Documentation/devicetree/bindings/arm/l2c2x0.yaml
arch/arm/boot/dts/exynos4210-i9100.dt.yaml: l2-cache-controller@10502000:
$nodename:0: 'l2-cache-controller@10502000' does not match '
^(cache-controller|cpu)(@[0-9a-f,]+)*$'
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The SDHCI on Tegra30 is in fact not backwards-compatible with the
instantiation found on earlier SoCs. Drop the misleading compatible
string.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The display controller on Tegra30 is in fact not backwards-compatible
with the instantiation found on earlier SoCs. Drop the misleading
compatible string.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This was probably left there by mistake or perhaps was a typo in the
first place. Remove it.
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DSI output needs to specify a parent clock that will be used to
drive both the output and the display controller.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Seaboard uses a non-existing, possibly obsoleted, binding for the
battery. Move to the standard binding which seems to be a super-
set of the odl binding.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Unit-addresses should be numeric. This fixes a validation failure seen
using the json-schema tooling.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Simple panels can only have a single power supply. The second listed
supply is not needed because it is also the input supply of the first
supply and therefore will always be on at the same time.
In retrospect the panel probably doesn't qualify as simple since it
apparently does need both of these supplies, even if in the case of the
Medcom Wide it isn't necessary to explicitly hook them up.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use commas rather than underscores to separate the various parts of the
unit-address in CPU OPPs to make them properly validate under the json-
schema bindings.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This is purely to make the json-schema validation tools happy because
they cannot deal with string arrays that may be in arbitrary order.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The memory controller exposes a set of memory client resets and needs to
specify the #reset-cells property in order to advertise the number of
cells needed to describe each of the resets.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tuple boundaries should be marked by < and > to make it clear which
cells are part of the same tuple. This also helps the json-schema based
validation tooling to properly parse this data.
While at it, also remove the "immovable" bit from PCI addresses. All of
these addresses are in fact "movable".
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Ethernet device should be named "ethernet@<unit-address>".
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Audio codecs need a #sound-dai-cells property, so add one to the audio
codecs on various Tegra-based boards that don't have one.
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SDHCI controller instantiated on Tegra114 is not backwards-
compatible with the version on Tegra30, so remove the corresponding
compatible string.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The new json-schema based validation tools require SD/MMC controller
nodes to be named mmc. Rename all references to them.
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The parent clocks are determined by the output that will be used, not by
the display controller that drives the output. On previous generations a
simple RGB output used to be part of the display controller and hence an
explicit parent clock needed to be assigned to the display controller to
drive the RGB output. Starting with Tegra124, that RGB output has been
dropped and the parent clock can therefore be removed from the display
controller device tree nodes.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The display controller on Tegra114 is in fact not backwards-compatible
with the instantiation found on earlier SoCs. Drop the misleading
compatible string.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The instantiation of gr3d in Tegra114 is not backwards-compatible with
the version found on earlier chips. Remove the misleading compatible
string.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The instantiation of gr2d in Tegra114 is not backwards-compatible with
the version found on earlier chips. While the hardware IP is identical,
the compatible string also describes the integration of the IP, which
in the case of Tegra114 is slightly different in that it's part of the
HEG power partition, whereas it wasn't previously.
Drop the misleading compatible string so that drivers that support the
older integrations cannot match on it. Since they wouldn't be able to
control the power partition, such driver wouldn't be able to access any
of the registers of the IP.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The host1x device tree bindings require the clock- and interrupt-names
properties to be present, so add them where missing.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The correct DSI/CSI supply property is called vdd-dsi-csi-supply, so use
that instead of the wrong vdd-supply property.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The correct DSI/CSI supply property is called vdd-dsi-csi-supply, so use
that instead of the wrong vdd-supply property.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The standard way to do this is to list out the regulators at the top
level. Adopt the standard way to fix validation.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The standard way to do this is to list out the clocks at the top-level.
Adopt the standard way to fix validation.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra SDHCI controller bindings state that the clock-names property
is required, so add the missing properties on Tegra114.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The WDOG_ANY signal is connected to the RESET_IN signal of the SoM
and baseboard. It is currently configured as push-pull, which means
that if some external device like a programmer wants to assert the
RESET_IN signal by pulling it to ground, it drives against the high
level WDOG_ANY output of the SoC.
To fix this we set the WDOG_ANY signal to open-drain configuration.
That way we make sure that the RESET_IN can be asserted by the
watchdog as well as by external devices.
Fixes: 1ea4b76cdf ("ARM: dts: imx6ul-kontron-n6310: Add Kontron i.MX6UL N6310 SoM and boards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The watchdog's WDOG_ANY signal is used to trigger a POR of the SoC,
if a soft reset is issued. As the SoM hardware connects the WDOG_ANY
and the POR signals, the watchdog node itself and the pin
configuration should be part of the common SoM devicetree.
Let's move it from the baseboard's devicetree to its proper place.
Fixes: 1ea4b76cdf ("ARM: dts: imx6ul-kontron-n6310: Add Kontron i.MX6UL N6310 SoM and boards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The L1 and L3 lines drive NMOS transistors that are OFF with a low level.
On the SAM9X60 EK board, if the pins corresponding to L1 and L3
have pull-ups enabled, there is an extra 2 x 30uA power consumption.
Use pull-downs for these 2 lines to remove the unnecessary power
consumption.
Fixes: 1e5f532c27 ("ARM: dts: at91: sam9x60: add device tree for soc and board")
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200615095525.43414-2-codrin.ciubotariu@microchip.com
The R1 and R3 lines drive NMOS transistors that are OFF with a low level.
On the SAMA5D2 Xplained board, if the pins corresponding to R1 and R3
have pull-ups enabled, there is an extra 2 x 30uA power consumption.
Use pull-downs for these 2 lines to remove the unnecessary power
consumption.
Fixes: b133ca7a65 ("ARM: dts: at91: sama5d2_xplained: add pin muxing and enable classd")
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200615095525.43414-1-codrin.ciubotariu@microchip.com
The FA2 mailbox is specified at 0x18025000 but should actually be
0x18025c00, length 0x400 according to socregs_nsp.h and board_bu.c. Also
the interrupt was off by one and should be GIC SPI 151 instead of 150.
Fixes: 17d5171723 ("ARM: dts: NSP: Add mailbox (PDC) to NSP")
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Veyron Jaq and Mighty both use the Marvel 8897 WiFi+BT chip. Add wakeup
and pinctrl block to devicetree so the btmrvl driver can correctly
configure the wakeup interrupt.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200612130219.v2.1.I66864be898aa835ccb66b6cd5220d0b082338a81@changeid
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives for example this error:
arch/arm/boot/dts/rk3288-tinker.dt.yaml: tsadc: otp-gpio:
{'phandle': [[54]], 'rockchip,pins': [[0, 10, 0, 118]]}
is not of type 'array'
'gpio' is a sort of reserved nodename and should not be used
for pinctrl in combination with 'rockchip,pins', so change
nodes that end with 'gpio' to end with 'pin' or 'pins'.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/
dtschema/schemas/gpio/gpio.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200524160636.16547-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Since commit cd28d1d6e5 ("net: phy: at803x: Disable phy delay for
RGMII mode") the networking is broken on the BeagleBone AI which has
the AR8035 PHY for Gigabit Ethernet [0]. The fix is to switch from
phy-mode = "rgmii" to phy-mode = "rgmii-rxid".
Note: Grygorii made a similar DT fix for other AM57xx boards with a
different phy in commit 820f8a870f ("ARM: dts: am57xx: fix networking
on boards with ksz9031 phy").
[0] https://git.io/Jf7PX
Fixes: 520557d485 ("ARM: dts: am5729: beaglebone-ai: adding device tree")
Cc: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
I accidentally flipped the system timer to use system clock instead of
the 32k source clock.
Fixes: 14b1925a72 ("ARM: dts: Configure system timers for omap4")
Signed-off-by: Tony Lindgren <tony@atomide.com>
While testing the recent suspend and resume regressions I noticed that
duovero can still end up losing edge gpio interrupts on runtime
suspend. This causes NFSroot easily stopping working after resume on
duovero.
Let's fix the issue by using gpio level interrupts for smsc as then
the gpio interrupt state is seen by the gpio controller on resume.
Fixes: 731b409878 ("ARM: dts: Configure duovero for to allow core retention during idle")
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM3358 pin mcasp0_aclkr (ZCZ ball B13) [0] is routed to P1.31 header [1]
Mode 4 of this pin is mmc0_sdwp (SD Write Protect). A signal connected
to P1.31 may accidentally trigger mmc0 write protection. To avoid this
situation, do not put mcasp0_aclkr in mode 4 (mmc0_sdwp) by default.
[0] http://www.ti.com/lit/ds/symlink/am3358.pdf
[1] https://github.com/beagleboard/pocketbeagle/wiki/System-Reference-Manual#531_Expansion_Headers
Fixes: 047905376a (ARM: dts: Add am335x-pocketbeagle)
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pwr and status leds configuration and turn on pwr led by default for Orange
Pi Zero Plus 2 (both H3 and H5 variants).
Signed-off-by: Diego Rondini <diego.rondini@kynetics.com>
Link: https://lore.kernel.org/r/20200615130223.34464-2-diego.rondini@kynetics.com
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Enable support for USB OTG port on Orange Pi Zero Plus 2 (both H3 and H5
variants). As, according to the board schematics, the USB OTG port cannot
provide power to external devices, we set dr_mode to peripheral.
Signed-off-by: Diego Rondini <diego.rondini@kynetics.com>
Link: https://lore.kernel.org/r/20200615130223.34464-1-diego.rondini@kynetics.com
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Currently the PL330 is enabled by default. However if left in IDM reset, as is
the case with the Meraki and Synology NSP devices, the system will hang when
probing for the PL330's AMBA peripheral ID. We therefore should be able to
disable it in these cases.
The PL330 is also included among of the list of peripherals put into coherent
mode, so "dma-coherent" has been added here as well.
Fixes: 5fa1026a3e ("ARM: dts: NSP: Add PL330 support")
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add sleep and idle states to uart4 pin configuration.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add sleep and idle states to uart4 pin configuration.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Sleep pin configuration is refined for low power modes:
- "sleep" (no wakeup & console suspend enabled): put pins in analog state
to optimize power
- "idle" (wakeup capability): keep Rx pin in alternate function
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Update led nodes names to be aligned with yaml description
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add the missing #address-cells and #size-cells to spi node.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Fix the nodes names to be aligned with yaml description
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Driver doesn't use interrupt's name to get it so remove it from
the node.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Update led nodes names to be aligned with yaml description
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Update led nodes names to be aligned with yaml description
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Update led nodes names to be aligned with yaml description
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Driver doesn't use interrupt's name to get it so remove it from
the node.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Update led nodes names to be aligned with yaml description
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Update led nodes names to be aligned with yaml description
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Rename pwm pinctrl nodes name to matching with yaml bindings
requirements.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Driver doesn't use interrupt's name to get it so remove it from
the node.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Enable the stmpe811 touch screen on stm32429-disco board.
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds the pin configuration for I2C3 controller on
stm32f4.
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds I2C3 instances of the STM32F429 SoC
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds the pin configuration for ltdc and spi5 controller
on stm32f429-disco board.
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Enable spi5's dma configuration for graphics data output to
ilitek ili9341 panel via mipi dbi interface.
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add support for the camera daughter board which is connected to
iWave's RZ/G1H Qseven carrier board. Also enable ttySC[0135] and
ethernet1 interfaces.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com>
Link: https://lore.kernel.org/r/1591552659-21314-1-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add sound support for the RZ/G1H SoC (a.k.a. R8A7742).
This work is based on similar work done on the R8A7744 SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/1590526904-13855-3-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Describe internal PCI bridge devices, USB phy device and
link PCI USB devices to USB phy.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com>
Link: https://lore.kernel.org/r/1590356277-19993-7-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add DT nodes for the Advanced Power Management Units (APMU), and use the
enable-method to point out that the APMU should be used for SMP support.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/1589555337-5498-16-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the I2C[0-3] and IIC[0-3] device nodes to the R8A7742 device tree.
Automatic transmission for PMIC control is not available on IIC3 hence
compatible strings "renesas,rcar-gen2-iic" and "renesas,rmobile-iic" are
not added to iic3 node.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com>
Link: https://lore.kernel.org/r/1589555337-5498-4-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
There are several issues with the bluetooth node - the wrong
compatible was used (because the bcm4329 compatible didn't exist
when the node was added), the max rate was incorrect (due to
limitations in the samsung TTY driver which have now been fixed),
the clocks were not assigned properly so some rates didn't work,
and the some pinctrl settings weren't explicitly set. Fix all
of the above issues.
While we're at it, update from the deprecated host-wakeup-gpios
property to the host-wake interrupt.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Aries boards have a BMA023 accelerometer attached over i2c-gpio.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Aries boards have a GP2A light/proximity sensor attached over i2c-gpio.
As the chip outputs a current and the board has no current ADC, a
current shunt resistor and a voltage ADC are used.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Correct the fuelgauge definition because only the fuelgauge on
fascinate4g has interrupt support (and even then it was wrong).
Also, assign the GPIO pinctrl so the interrupt is properly configured
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The GPH3 pins on s5pv210 have interrupt support and had the
interrupt-cells property but was missing the interrupt-controller
property.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add a node for the BCM4354 Bluetooth chip on the serial bus #0 on
the Exynos3250-based Artik5 boards.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
On Exynos5422/5800 the regulator supply for the A15 cores ("vdd_arm") is
coupled with the regulator supply for the SoC internal circuits
("vdd_int"), thus all operating points that modify one of those supplies
have to specify a triplet of the min/target/max values to properly work
with regulator coupling.
Fixes: eaffc4de16 ("ARM: dts: exynos: Add missing CPU frequencies for Exynos5422/5800")
Cc: <stable@vger.kernel.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Set smbus_en of IO expander to 1 in order to be able to read sensor.
Signed-off-by: Ben Pai <Ben_Pai@wistron.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
LCD timings now come from panel-simple. Having timings in the DT will
cause a WARN.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
LCD timings now come from panel-simple. Having timings in the DT will
cause a WARN.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
LCD timings now come from panel-simple. Having timings in the DT will
cause a WARN.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
