The Exynos5260 GIC node does not have any children so remove the address
and size cells as they are not needed by DT bindings. The size-cells of
'0' were also incorrect. This fixes dtbs_check warning:
arch/arm/boot/dts/exynos5260-xyref5260.dt.yaml: interrupt-controller@10481000: #size-cells:0:0: 1 was expected
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200901075417.22481-4-krzk@kernel.org
Exynos5260 SoCs have ARM GIC 400. Correct the compatibles to match
dtschema and fix the dtbs_check warnings like:
arch/arm/boot/dts/exynos5260-xyref5260.dt.yaml: interrupt-controller@10481000:
compatible: ['arm,cortex-a15-gic', 'arm,cortex-a9-gic'] is not valid under any of the given schemas
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200901075417.22481-3-krzk@kernel.org
Exynos5250 and Exynso54xx SoCs have ARM GIC 400. Correct the
compatibles to match dtschema and fix the dtbs_check warnings like:
arch/arm/boot/dts/exynos5420-peach-pit.dt.yaml: interrupt-controller@10481000:
compatible: ['arm,gic-400', 'arm,cortex-a15-gic', 'arm,cortex-a9-gic']
is not valid under any of the given schemas
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200901075417.22481-2-krzk@kernel.org
The reg property is mandatory for cpu nodes, also fix the #address-cells of
the cpus node that has to be at least 1.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20200831171129.3886857-2-alexandre.belloni@bootlin.com
Both the Galaxy S and the Fascinate4G have a WM8994 codec, but they
differ slightly in their jack detection and micbias configuration.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The S3C RTC requires 32768 Hz clock as input which is provided by PMIC.
However the PMIC is not described in DTS at all so at least add a
workaround to model its clock with fixed-clock. This fixes S3C RTC and
silences dtbs_check warnings like:
arch/arm/boot/dts/exynos4412-tiny4412.dt.yaml: rtc@10070000: clocks: [[7, 346]] is too short
arch/arm/boot/dts/exynos4412-tiny4412.dt.yaml: rtc@10070000: clock-names: ['rtc'] is too short
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-32-krzk@kernel.org
The S3C RTC requires 32768 Hz clock as input which is provided by PMIC.
However the PMIC is not described in DTS at all so at least add a
workaround to model its clock with fixed-clock and silence dtbs_check
warnings like:
arch/arm/boot/dts/exynos4412-smdk4412.dt.yaml: rtc@10070000: clocks: [[7, 346]] is too short
arch/arm/boot/dts/exynos4412-smdk4412.dt.yaml: rtc@10070000: clock-names: ['rtc'] is too short
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-31-krzk@kernel.org
Add missing cooling devices for CPU thermal zones in Exynos4412 Tiny4412
board. This allows to scale down CPU frequency (and voltage) in case of
thermal pressure.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-30-krzk@kernel.org
Add missing cooling devices for CPU thermal zones in Exynos4412 SMDK4412
board. This allows to scale down CPU frequency (and voltage) in case of
thermal pressure.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-29-krzk@kernel.org
Add missing cooling devices for CPU thermal zones in Exynos4412 Origen
board. This allows to scale down CPU frequency (and voltage) in case of
thermal pressure.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-28-krzk@kernel.org
Using full paths to extend or override a device tree node is error prone
since if there was a typo error, a new node will be created instead of
extending the node as it was desired. This will lead to run-time errors
that could be hard to detect.
A mistyped label on the other hand, will cause a dtc compile error
(during build time).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-27-krzk@kernel.org
Using full paths to extend or override a device tree node is error prone
since if there was a typo error, a new node will be created instead of
extending the node as it was desired. This will lead to run-time errors
that could be hard to detect.
A mistyped label on the other hand, will cause a dtc compile error
(during build time).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-26-krzk@kernel.org
Add node for clock controller of Samsung S5M8767 PMIC. This provides
the 32768 Hz clock required by S3C RTC. Except making the S3C RTC
working, this also fixes dtbs_check warnings:
arch/arm/boot/dts/exynos4412-origen.dt.yaml: rtc@10070000: clocks: [[7, 346]] is too short
arch/arm/boot/dts/exynos4412-origen.dt.yaml: rtc@10070000: clock-names: ['rtc'] is too short
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-25-krzk@kernel.org
The fixed clocks implemented by Samsung clock drivers use only one
compatible so drop the additional "fixed-clock" to fix dtbs_check
warnings like:
arch/arm/boot/dts/exynos4412-i9300.dt.yaml: xxti: compatible:0: 'fixed-clock' was expected
From schema: Documentation/devicetree/bindings/clock/fixed-clock.yaml
arch/arm/boot/dts/exynos4412-i9300.dt.yaml: xxti: compatible: ['samsung,clock-xxti', 'fixed-clock'] is too long
arch/arm/boot/dts/exynos4412-i9300.dt.yaml: xxti: compatible: Additional items are not allowed ('fixed-clock' was unexpected)
arch/arm/boot/dts/exynos4412-i9300.dt.yaml: xxti: '#clock-cells' is a required property
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-24-krzk@kernel.org
Align the name of mag-mhl-gpio node to avoid dtschema confusion and
dtbs_check warning:
arch/arm/boot/dts/exynos4210-i9100.dt.yaml: pinctrl@11000000: mag-mhl-gpio:
{'samsung,pins': ['gpd0-2'], 'samsung,pin-function': [[3]], 'samsung,pin-pud': [[0]]} is not of type 'array'
From schema: dtschema/schemas/gpio/gpio-consumer.yaml
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-22-krzk@kernel.org
Add missing cooling devices for CPU thermal zones in Exynos4210
Universal C310 board. This allows to scale down CPU frequency (and
voltage) in case of thermal pressure.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-21-krzk@kernel.org
Add missing cooling devices for CPU thermal zones in Exynos4210 SMDKv310
board. This allows to scale down CPU frequency (and voltage) in case of
thermal pressure.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-20-krzk@kernel.org
Add missing cooling devices for CPU thermal zones in Exynos4210 Origen
board. This allows to scale down CPU frequency (and voltage) in case of
thermal pressure.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-19-krzk@kernel.org
Using full paths to extend or override a device tree node is error prone
since if there was a typo error, a new node will be created instead of
extending the node as it was desired. This will lead to run-time errors
that could be hard to detect.
A mistyped label on the other hand, will cause a dtc compile error
(during build time).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-18-krzk@kernel.org
Using full paths to extend or override a device tree node is error prone
since if there was a typo error, a new node will be created instead of
extending the node as it was desired. This will lead to run-time errors
that could be hard to detect.
A mistyped label on the other hand, will cause a dtc compile error
(during build time).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-17-krzk@kernel.org
Using full paths to extend or override a device tree node is error prone
since if there was a typo error, a new node will be created instead of
extending the node as it was desired. This will lead to run-time errors
that could be hard to detect.
A mistyped label on the other hand, will cause a dtc compile error
(during build time).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-16-krzk@kernel.org
The device tree schema expects SPI controller to be named "spi",
otherwise dtbs_check complain with a warning like:
arch/arm/boot/dts/exynos4210-i9100.dt.yaml: spi-lcd:
$nodename:0: 'spi-lcd' does not match '^spi(@.*|-[0-9a-f])*$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-15-krzk@kernel.org
"gpio-sck" and "gpio-mosi" are deprecated so update the DTS to fix
dtbs_checks warnings like:
arch/arm/boot/dts/exynos4210-universal_c210.dt.yaml: spi-lcd:
gpio-sck: False schema does not allow [[85, 1, 0]]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200830135200.24304-14-krzk@kernel.org
The device tree schema expects SPI controller to be named "spi",
otherwise dtbs_check complain with a warning like:
arch/arm/boot/dts/exynos4210-universal_c210.dt.yaml: spi-lcd:
$nodename:0: 'spi-lcd' does not match '^spi(@.*|-[0-9a-f])*$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-13-krzk@kernel.org
The PMIC has a 32768 Hz clock used by the modem which is implemented by
driver as a regulator. Add and enable it to be sure modem get's its
signal.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-10-krzk@kernel.org
The PMIC has a 32768 Hz clock used by the modem which is implemented by
driver as a regulator. Add and enable it to be sure modem get's its
signal.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-8-krzk@kernel.org
The S3C RTC requires 32768 Hz clock as input which is provided by PMIC.
However there is no clock provided for the PMIC and the driver registers
the clock as regulator. This is an old driver which will not be updated
so add a workaround - a fixed-clock to fill missing clock phandle
reference in S3C RTC.
This allows to enable the S3C RTC and fixes dtbs_check warnings:
arch/arm/boot/dts/exynos4210-smdkv310.dt.yaml: rtc@10070000: clocks: [[5, 346]] is too short
arch/arm/boot/dts/exynos4210-smdkv310.dt.yaml: rtc@10070000: clock-names: ['rtc'] is too short
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-7-krzk@kernel.org
The S3C RTC requires 32768 Hz clock as input which is provided by PMIC.
However there is no clock provided for the PMIC and the driver registers
the clock as regulator. This is an old driver which will not be updated
so add a workaround - add a fixed-clock to fill missing clock phandle
reference in S3C RTC. The "clock" regulator in PMIC is already present
and enabled.
This allows to enable the S3C RTC and fixes dtbs_check warnings:
arch/arm/boot/dts/exynos4210-universal_c210.dt.yaml: rtc@10070000: clocks: [[5, 346]] is too short
arch/arm/boot/dts/exynos4210-universal_c210.dt.yaml: rtc@10070000: clock-names: ['rtc'] is too short
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200830135200.24304-6-krzk@kernel.org
The S3C RTC requires 32768 Hz clock as input which is provided by PMIC
(Maxim MAX8997). However there is no clock provided for the PMIC and
the driver registers the clock as regulator. This is an old driver
which will not be updated so add a workaround:
1. Enable the "clock" regulator in PMIC,
2. Add a fixed-clock to fill missing clock phandle reference in S3C RTC.
This allows to enable the S3C RTC and fixes dtbs_check warnings:
arch/arm/boot/dts/exynos4210-trats.dt.yaml: rtc@10070000: clocks: [[5, 346]] is too short
arch/arm/boot/dts/exynos4210-trats.dt.yaml: rtc@10070000: clock-names: ['rtc'] is too short
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200830135200.24304-5-krzk@kernel.org
The S3C RTC requires 32768 Hz clock as input which is provided by PMIC
(Maxim MAX8997). However there is no clock provided for the PMIC and
the driver registers the clock as regulator. This is an old driver
which will not be updated so add a workaround:
1. Enable the "clock" regulator in PMIC,
2. Add a fixed-clock to fill missing clock phandle reference in S3C RTC.
This allows to enable the S3C RTC and fixes dtbs_check warnings:
arch/arm/boot/dts/exynos4210-origen.dt.yaml: rtc@10070000: clocks: [[5, 346]] is too short
arch/arm/boot/dts/exynos4210-origen.dt.yaml: rtc@10070000: clock-names: ['rtc'] is too short
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200830135200.24304-4-krzk@kernel.org
The S3C RTC requires 32768 Hz clock as input which is provided by PMIC
(Maxim MAX8997). However there is no clock provided for the PMIC and
the driver registers the clock as regulator. This is an old driver
which will not be updated so add a workaround:
1. Enable the "clock" regulator in PMIC,
2. Add a fixed-clock to fill missing clock phandle reference in S3C RTC.
This allows to enable the S3C RTC and fixes dtbs_check warnings:
arch/arm/boot/dts/exynos4210-i9100.dt.yaml: rtc@10070000: clocks: [[5, 346]] is too short
arch/arm/boot/dts/exynos4210-i9100.dt.yaml: rtc@10070000: clock-names: ['rtc'] is too short
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-3-krzk@kernel.org
The regulator property 'regulator-microvolt-offset' should be put next
to regulator definition, not consumer.
The property 'regulator-microsecs-delay' is not valid at all.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-2-krzk@kernel.org
The name of I2C controller over GPIO lines node ends with '-gpio' which
confuses dtschema:
/arch/arm/boot/dts/exynos4210-i9100.dt.yaml: /: i2c-gpio:
{'compatible': ['i2c-gpio'], ... 'maxim,over-volt': [[4500]]}} is not of type 'array'
From schema: lib/python3.6/site-packages/dtschema/schemas/gpio/gpio-consumer.yaml
Add a '-0' suffix to silence it. This pattern on naming i2c-gpio is
already present in many other dts. No functional change.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-1-krzk@kernel.org
The binding for DesignWare HS OTG USB 2.0 in Samsung SoCs take only one
compatible. This fixes dtbs_check warnings like:
arch/arm/boot/dts/exynos3250-artik5-eval.dt.yaml: hsotg@12480000:
compatible: ['samsung,s3c6400-hsotg', 'snps,dwc2'] is not valid under any of the given schemas (Possible causes of the failure):
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200829172532.29358-4-krzk@kernel.org
The fixed clocks are kept under dedicated node fixed-rate-clocks, thus a
fake "reg" was added. This is not correct with dtschema as fixed-clock
binding does not have a "reg" property:
arch/arm/boot/dts/exynos3250-artik5-eval.dt.yaml: clock@0: 'reg' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200829172532.29358-2-krzk@kernel.org
Add support for the SPI NOR device used to boot up the system
to the System on Module DT.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Link: https://lore.kernel.org/r/20200825085435.8744-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The following dtc warning is seen when building with W=1:
arch/arm/boot/dts/imx6qdl-gw553x.dtsi:65.12-110.4: Warning (avoid_unnecessary_addr_size): /gpio-keys: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Remove the unneeded #address-cells/#size-cells properties to fix the issue.
Fixes: 64bf0a0af1 ("ARM: dts: imx6qdl-gw: add Gateworks System Controller support")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Headphone detection is triggered by GPIO, then driver can
switch between speaker and headphone.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Headphone detection is triggered by GPIO, then driver can
switch between speaker and headphone.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
While the DT parser recognizes "ok" as a valid value for the
"status" property, it is actually mentioned nowhere. Use the
proper value "okay" instead, as done in the majority of files
already.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Link: https://lore.kernel.org/r/20200830190820.20583-1-freifunk@adrianschmutzler.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The use of cpu0-supply for cpu0 alone is deprecated,
so add cpu-supply to each cpu separately and
update all existing rk3066a boards.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200813172451.13754-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The use of cpu0-supply for cpu0 alone is deprecated,
so add cpu-supply to each cpu separately and
update all existing rk3288 boards that use this property.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200813180241.14660-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The property "fsl,spi-num-chipselects" is gone since commit 790739c441
("dt-bindings: spi: Convert imx cspi to json-schema").
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The conversion of the spi-imx driver to use GPIO descriptors
in commit 8cdcd8aeee ("spi: imx/fsl-lpspi: Convert to GPIO descriptors")
helped to detect the following SPI chipselect polarity mismatch on an
imx6q-sabresd:
[ 4.854337] m25p80@0 enforce active low on chipselect handle
Prior to the above commit, the chipselect polarity passed via cs-gpios
property was ignored and considered active-low.
The reason for such mismatch is clearly explained in the comments inside
drivers/gpio/gpiolib-of.c:
* SPI children have active low chip selects
* by default. This can be specified negatively
* by just omitting "spi-cs-high" in the
* device node, or actively by tagging on
* GPIO_ACTIVE_LOW as flag in the device
* tree. If the line is simultaneously
* tagged as active low in the device tree
* and has the "spi-cs-high" set, we get a
* conflict and the "spi-cs-high" flag will
* take precedence.
To properly represent the SPI chipselect polarity, change it to active-low
when the "spi-cs-high" property is absent.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SoC supports three pcie ports. Currently, only
pcie0 and pcie1 are enabled. This patch adds the
pcie2 port as well.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The BCM53016 in the Meraki MR32 utilizes the third "uart2"
to connect to a on-board Bluetooth-LE 4.0 BCM20732 chip.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The BCM53016 in the Meraki MR32 uses the on-chip PWM
controller to drive a tri-color RGB LED. Since I plan
to use the PWM, I made a label for the pwm's pinmux
node. This way, it can be easily referenced.... And
Also included a label for the i2c since I'm going to
need it in the future too.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This patch adds support for the GARDENA smart Gateway, which is based on
the Atmel AT91SAM9G25. It is equipped with 128 MiB of DDR2 RAM and
256 MiB NAND storage.
Please note that this gateway is not actually based on a AT91SAM9x5 EK
board, but is close enough to allow its DT to be used.
Co-developed-by: Stefan Roese <sr@denx.de>
Co-developed-by: Michael Zimmermann <michael.zimmermann@grandcentrix.net>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michael Zimmermann <michael.zimmermann@grandcentrix.net>
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200822151023.31629-2-code@reto-schneider.ch
Enable BQ32000 RTC which is connected to I2C0 on the iWave RainboW-G21M-q7
SOM.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Link: https://lore.kernel.org/r/20200816193316.7641-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
DCDC1 regulator powers many different subsystems. While some of them can
work at 3.0 V, some of them can not. For example, VCC-HDMI can only work
between 3.24 V and 3.36 V. According to OS images provided by the board
manufacturer this regulator should be set to 3.3 V.
Set DCDC1 and DCDC1SW to 3.3 V in order to fix this.
Fixes: da7ac948fa ("ARM: dts: sun8i: Add board dts file for Banana Pi M2 Ultra")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200824193649.978197-1-jernej.skrabec@siol.net
Fix the VGA reserved memory node, and add the XDMA engine node,
enable it, and point it's memory region to the VGA memory.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add initial version of device tree for Facebook Wedge400 (AST2500) BMC.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20200824211948.12852-6-rentao.bupt@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Set 64Mb FMC flash layout in Minipack device tree explicitly because the
flash layout was removed from "ast2500-facebook-netbmc-common.dtsi".
Please note "data0" partition' size is updated to 4MB to be consistent
with other Facebook OpenBMC platforms.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Link: https://lore.kernel.org/r/20200824211948.12852-5-rentao.bupt@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Set 32MB FMC flash layout in Yamp device tree explicitly because flash
layout settings were removed from "ast2500-facebook-netbmc-common.dtsi".
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Link: https://lore.kernel.org/r/20200824211948.12852-4-rentao.bupt@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Set 32MB FMC flash layout in CMM device tree explicitly because the flash
layout settings were removed from "ast2500-facebook-netbmc-common.dtsi".
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Link: https://lore.kernel.org/r/20200824211948.12852-3-rentao.bupt@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Remove FMC flash layout from ast2500-facebook-netbmc-common.dtsi because
flash size and layout varies across different Facebook AST2500 OpenBMC
platforms.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Link: https://lore.kernel.org/r/20200824211948.12852-2-rentao.bupt@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
All IO mapped SoC peripherals should be within the "soc" node. Move the
L2 cache-controller there as well since it's the only one not following
this pattern.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200815182223.408965-1-martin.blumenstingl@googlemail.com
- Fix QuadSPI-memory 'reg' for LS1021A and GPIO 'ranges' for i.MX7ULP
pinctrl.
- A couple of DTC warning fixes on imx6qdl-gw51xx and imx6q-prtwd2
boards.
- Add missing imx8mm-beacon-kit.dtb to dtbs-y for build coverage.
- Fix broken PWM settings on imx6q-logicpd board.
- Add missing syscon compatible to OCOTP device, so that access to UID
is possible.
- Fix a network regression on imx7d-zii-rmu2 due to a phy-mode mismatch.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl9DuhsUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM5bSQf/b+yNiCFHg86Jmwcm+drrLRns8N6j
Xzy8U+LYxqjGyXOhYthuPU4K4y76qGh8Gaa1FlUJcaGdJ4nn/3RXw1kAAUaE9QT4
UDm/j5bdrDiyCOJf54XPOTjq9VVJjKuHa9yGQykTc7uI0pQ0O1zWWP1X1ZBV3Z7l
dCxtbBdvczrHW2sssCSyKL3YoTNo4TCXSE77TAFjVsz/VzbvuHXyn4GPDWt7jofz
4m/UEx4irNRwTuunJ9aFqVf6MsjrlHJYGHBqr1Oh2+uhoQpM5FbjuE436C8kgVpY
u/mKBf7UtnhWUQIG1O7/pCwojh3QKSh0p77swnau/sTzmVFZ7tzBe6WSAw==
=yno7
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.9:
- Fix QuadSPI-memory 'reg' for LS1021A and GPIO 'ranges' for i.MX7ULP
pinctrl.
- A couple of DTC warning fixes on imx6qdl-gw51xx and imx6q-prtwd2
boards.
- Add missing imx8mm-beacon-kit.dtb to dtbs-y for build coverage.
- Fix broken PWM settings on imx6q-logicpd board.
- Add missing syscon compatible to OCOTP device, so that access to UID
is possible.
- Fix a network regression on imx7d-zii-rmu2 due to a phy-mode mismatch.
* tag 'imx-fixes-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx7d-zii-rmu2: fix rgmii phy-mode for ksz9031 phy
ARM: dts: vfxxx: Add syscon compatible with OCOTP
ARM: dts: imx6q-logicpd: Fix broken PWM
arm64: dts: imx: Add missing imx8mm-beacon-kit.dtb to build
ARM: dts: imx6q-prtwd2: Remove unneeded i2c unit name
ARM: dts: imx6qdl-gw51xx: Remove unneeded #address-cells/#size-cells
ARM: dts: imx7ulp: Correct gpio ranges
ARM: dts: ls1021a: fix QuadSPI-memory reg range
Link: https://lore.kernel.org/r/20200824130359.GF12776@dragon
Signed-off-by: Olof Johansson <olof@lixom.net>
Since commit bcf3440c6d ("net: phy: micrel: add phy-mode support for the
KSZ9031 PHY") the networking is broken on the imx7d-zii-rmu2 board.
The end result is that network receive behaviour is marginal with lots of
RX CRC errors experienced and NFS frequently failing.
Quoting the explanation from Andrew Lunn in commit 0672d22a19
("ARM: dts: imx: Fix the AR803X phy-mode"):
"The problem here is, all the DTs were broken since day 0. However,
because the PHY driver was also broken, nobody noticed and it
worked. Now that the PHY driver has been fixed, all the bugs in the
DTs now become an issue"
Fix it by switching to phy-mode = "rgmii-id".
Fixes: bcf3440c6d ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY")
Signed-off-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Keerthy <j-keerthy@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Note that we also must tag rtc as disabled on am43x-epos-evm as
it's not accessible according to commit 4321dc8dff ("ARM: AM43XX:
hwmod: Add rtc hwmod"). And we must keep RTC enabled for rtcwake
to work now that we've removed the custom platfor code for
re-enabling the RTC on suspend.
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DTC doesn't like the default PWM settings, because it's expecting
three cells. This patch reduces adds the extra entry of 0 to the PWM
reference.
Fixes: fa28d8212e ("ARM: dts: imx: default to #pwm-cells = <3> in the SoC dtsi files")
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The following dtc warning is seen when building with W=1:
arch/arm/boot/dts/imx6q-prtwd2.dts:33.8-43.4: Warning (unit_address_vs_reg): /i2c@4: node has a unit name, but no reg or ranges property
Remove the unneeded i2c unit name to fix the issue.
Fixes: 88010b8174 ("ARM: dts: add Protonic WD2 board")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The following dtc warning is seen when building with W=1:
arch/arm/boot/dts/imx6qdl-gw51xx.dtsi:23.12-68.4: Warning (avoid_unnecessary_addr_size): /gpio-keys: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Remove the unneeded #address-cells/#size-cells properties to fix the issue.
Fixes: 64bf0a0af1 ("ARM: dts: imx6qdl-gw: add Gateworks System Controller support")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the reference manual of the i.MX25 the function name for
the GPT capture input is called CAPIN1. So fix the names to follow the
same naming scheme as used for the other pads and functions. Also add
one missing pad function.
There are no mainline users that needs adaption.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the reg property to each channel node. This update is
to accommodate the multicolor framework. In addition to the
accommodation this allows the LEDs to be placed on any channel
and allow designs to skip channels as opposed to requiring
sequential order.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
CC: Shawn Guo <shawnguo@kernel.org>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Pengutronix Kernel Team <kernel@pengutronix.de>
CC: Fabio Estevam <festevam@gmail.com>
CC: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds missing interrupt support for the internal Marvell
switch, so that the kernel does not have to keep polling the
PHYs on the bit-banged MDIO bus all the time.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add "DMIC" rounting, headphone and microphone detect gpio for sound
card, then output sound can switch between headphone and speaker.
input sound can switch between DMIC and AMIC.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
I used the i.MX25 Reference Manual (Rev 2 01/2011) as source for these
additions and fixes.
No mainline dts is affected by the fixes (nor obviously by the
additions).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Correct gpio ranges according to i.MX7ULP pinctrl driver:
gpio_ptc: ONLY pin 0~19 are available;
gpio_ptd: ONLY pin 0~11 are available;
gpio_pte: ONLY pin 0~15 are available;
gpio_ptf: ONLY pin 0~19 are available;
Fixes: 20434dc92c ("ARM: dts: imx: add common imx7ulp dtsi support")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
OLED display consist of an OLED panel and a display controller.
The displays that were used on yapp4 platform were based on a SSD1305
controller. These displays are now discontinued and we need to add
support for a replacement.
The new display is based on SSD1309 controller and requires slightly
different configuration (mirror + segment offset). We want to support
both display types so it does no matter which one was used on the assembly
line. Hence the displays are placed at different I2C addresses.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add devicetree for new variant of the Y Soft IOT appliance.
The board is based on Hydra with the following changes:
- faster SoC (1GHz), 4GB RAM and 64GB eMMC
- removed miniPCIe
- removed Audio jack
- removed uSD slot
- removed RJ10 serial
- HDMI replaced by USB host
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change i.MX SoCs nand node name from "gpmi-nand" to "nand-controller" to
be compliant with yaml schema, it requires the nodename to be
"nand-controller".
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change i.MX27 nand node name from "nand" to "nand-controller" to
be compliant with yaml schema, it requires the nodename to be
"nand-controller".
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add aliases for ethernet switch ports to allow bootloader to fix
MAC addresses to the ones stored in onboard configuration EEPROM.
Ursa has only one ethernet port populated (eth2) so alias for
the first port has to be removed on this board.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In preparation for an update of the TQ-Systems TQMa7x/MBa7x DTS, add the
QSPI controller to imx7s.dtsi.
Based-on-patch-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the Reference Manual, the correct size is 512 MiB.
Without this fix, probing the QSPI fails:
fsl-quadspi 1550000.spi: ioremap failed for resource
[mem 0x40000000-0x7fffffff]
fsl-quadspi 1550000.spi: Freescale QuadSPI probe failed
fsl-quadspi: probe of 1550000.spi failed with error -12
Fixes: 85f8ee78ab ("ARM: dts: ls1021a: Add support for QSPI with ls1021a SoC")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently, OMAP3_THERMAL is disabled by default, so the bandgap sensor
is unavailable, and enabling it will somewhat increase power consumption.
However for boards which operate near their thermal limit, OMAP3_THERMAL
can be enabled and monitored to keep the processor from either running
too fast, or shutdown when it's deemed to be operating at an unsafe
thermal limit at the expense of increased power consumption.
The OMAP3530, OMAP3630, and DM3730 all show thresholds of 90C and 105C
depending on commercial or extended temperature ratings.
This patch expands the thermal information to include the limits of
80C for alert and 90C critical based on commercial temperature rating.
It sets the coolings-cells for the 34xx and 36xx CPU's which will start
to throttle back their maximum frequency when the bangap sensor reads
above the alert temerature of 80C.
For boards who which to increase the temperatures for extended
temperature ratings, these can be changed on their respective
device trees with something like:
&cpu_alert0 {
temperature = <90000>; /* millicelsius */
};
&cpu_crit {
temperature = <105000>; /* millicelsius */
};
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com> # on GTA04A5 with dm3730cbp100
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add label to the ocp node in the AM33xx SoC include so that it can be
referenced in board-level files like am335x-pocketbeagle.dts
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add am335x-moxa-uc-8100-common.dtsi for many products of MOXA UC-8100
series, and remove common nodes from am335x-moxa-uc-8100-me-t.dts.
Signed-off-by: Johnson Chen <johnsonch.chen@moxa.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add information about panel orientation, so that the
system boots into a properly rotated shell.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add Droid 4 specific compatible value in addition to the
generic one, so that we have the ability to add panel
specific quirks in the future.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The standard binding for DSI requires that the channel number
of the panel is encoded in DT. This adds the channel number in
all OMAP3-5 boards in preparation for using common infrastructure.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We currently have a different clock rate for droid4 compared to the
stock v3.0.8 based Android Linux kernel:
# cat /sys/kernel/debug/clk/dpll_*_m7x2_ck/clk_rate
266666667
307200000
# cat /sys/kernel/debug/clk/l3_gfx_cm:clk:0000:0/clk_rate
307200000
Let's fix this by configuring sgx to use 153.6 MHz instead of 307.2 MHz.
Looks like also at least duover needs this change to avoid hangs, so
let's apply it for all 4430.
This helps a bit with thermal issues that seem to be related to memory
corruption when using sgx. It seems that other driver related issues
still remain though.
Cc: Arthur Demchenkov <spinal.by@gmail.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DSI was not probing due to base address off by 0x1000, and sys_clk
missing.
With this patch, the Pyra display works if HDMI is disabled in the
device tree.
Fixes: 5a507162f0 ("ARM: dts: Configure interconnect target module for omap5 dsi1")
Signed-off-by: David Shah <dave@ds0.me>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
[tony@atomide.com: standardized subject line, added fixes tag]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The chip is hardwired to the board's PCIe bus and needs to be properly
setup trough a firmware routine after a PCI fundamental reset. Pass the
reset controller phandle that takes care of triggering the
initialization to the relevant PCI device.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20200629161845.6021-5-nsaenzjulienne@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the reset driver exposing Raspberry Pi 4's firmware based USB
reset routine is available, let's add the device tree node exposing it.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20200629161845.6021-4-nsaenzjulienne@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can power off l4_abe domain when not in use when we configure it for
genpd. And with that change, we can now also drop the old unused legacy
platform data.
Note that we also need to now use "simple-pm-bus" instead of "simple-bus"
for PM runtime to get enabled for the bus.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can power off the SGX power domain when not in use when we configure
it for genpd. And with that change, we can now also drop the old unused
legacy platform data.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the devicetree properties to enable instruction and data prefetch
on exynos4210 and exynos4412 which use the L2C-310 cache. No other
Exynos chip appears to be using this L2 cache hardware.
This follows the default bits being set in the l2c_aux_val register
for the Exynos platform, which can now be cleared as a result.
Signed-off-by: Guillaume Tucker <guillaume.tucker@collabora.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Update the never-mainlined "samsung,trats2-audio" binding and instead
use the new "samsung,midas-audio" binding.
Signed-off-by: Simon Shields <simon@lineageos.org>
[s.nawrocki: fixed DAPM routing entries for MICBIAS1/2, adjusted to
new cpu/codec binding, corrected the regulator nodes indexing]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Fixes the register address for the timer3 entry on Arria10.
Fixes: 475dc86d08 ("arm: dts: socfpga: Add a base DTSI for Altera's Arria10 SOC")
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Configure the SAI device node, configure audio clock
and pinctrl.
Enable the audio sound card, which use the SAI1 and
wm8960, and enable headphone detection.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add device trees for TQMa6S, TQMa6Q, and TQMa6QP embedded modules.
The A and B SoM variants are for hardware revisions that differ in
how the I2C devices are connected. For details, see [1].
This is a combination of the patches
"arm: dt: imx6qdl: add tqma6[qdl] som on mba6 mainboard",
"arm: dt: tqma6: add spi with spi nor flash on SOM",
"arm: dt: add basic support for tqma6qp on mba6", and
"arm: dt: imx6qdl-tqma6: use generic jedec,spi-nor"
from the TQMa6x BSP, with the MBa6 specific parts removed.
[1] https://support.tq-group.com/en/arm/tqma6x/linux/ptxdist/overview
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
[bst@pengutronix.de: remove unnecessary container node in the iomuxc
node]
Signed-off-by: Bastian Krause <bst@pengutronix.de>
[p.zabel@pengutronix.de: merged patches from TQMa6x BSP REV.0114,
separated MBa6 DTs, fixed checkpatch and dtbs_check warnings,
added no-sd(io) properties to eMMC, added SPDX license identifiers
and commit message]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Disable Ethernet switch reset GPIO with ZII platforms that have it
enabled. HW switch reset results in a reset of the copper PHYs
inside of the switch. We want to avoid this reset of the copper PHYs
in the switch as this results in unnecessary broader network disruption on
a soft reboot of the application processor.
With the HW GPIO removed, the switch driver still performs a soft reset of
the switch core which has been shown to sufficiently meet our needs with
other ZII platforms that do not have the HW switch reset GPIO defined.
Signed-off-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the reset-gpio property, and enable PCIe on iMX6QP SABREAUTO board.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A previous commit removed the panel-dpi driver, which made the
SOM-LV video stop working because it relied on the DPI driver
for setting video timings. Now that the simple-panel driver is
available in omap2plus, this patch migrates the SOM-LV dev kits
to use a similar panel and remove the manual timing requirements.
A similar patch was already done and applied to the Torpedo family.
Fixes: 8bf4b16211 ("drm/omap: Remove panel-dpi driver")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Older versions of U-Boot would pinmux the whole board, but as
the bootloader got updated, it started to only pinmux the pins
it needed, and expected Linux to configure what it needed.
Unfortunately this caused an issue with the audio, because the
mcbsp2 pins were configured in the device tree but never
referenced by the driver. When U-Boot stopped muxing the audio
pins, the audio died.
This patch adds the references to the associate the pin controller
with the mcbsp2 driver which makes audio operate again.
Fixes: 5cb8b0fa55 ("ARM: dts: Move most of logicpd-som-lv-37xx-devkit.dts to logicpd-som-lv-baseboard.dtsi")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Older versions of U-Boot would pinmux the whole board, but as
the bootloader got updated, it started to only pinmux the pins
it needed, and expected Linux to configure what it needed.
Unfortunately this caused an issue with the audio, because the
mcbsp2 pins were configured in the device tree, they were never
referenced by the driver. When U-Boot stopped muxing the audio
pins, the audio died.
This patch adds the references to the associate the pin controller
with the mcbsp2 driver which makes audio operate again.
Fixes: 739f85bba5 ("ARM: dts: Move most of logicpd-torpedo-37xx-devkit to logicpd-torpedo-baseboard")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
rng DT node was added without a compatible string.
i.MX driver for RNGC (drivers/char/hw_random/imx-rngc.c) also claims
support for RNGB, and is currently used for i.MX25.
Let's use this driver also for RNGB block in i.MX6SL.
Fixes: e29fe21cff ("ARM: dts: add device tree source for imx6sl SoC")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add a device node for the PCIe controller on the Renesas
RZ/G1H (r8a7742) SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Link: https://lore.kernel.org/r/20200810174156.30880-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add a Display Unit (DU) node to r8a7742 SoC DT.
Boards that want to enable the DU need to specify the output topology.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200807174954.14448-6-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Some r8a7745-iwg22d-sodimm.dts device nodes are not sorted alphabetically.
This patch fixes the sorting of nodes and also fixes a typo in the stmpe
node.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20200805142634.12252-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
kernel series:
Core changes:
- The GPIO patch "gpiolib: Introduce
for_each_requested_gpio_in_range() macro" was put in an
immutable branch and merged into the pinctrl tree as well.
We see these changes also here.
- Improved debug output for pins used as GPIO.
New drivers:
- Ocelot Sparx5 SoC driver.
- Intel Emmitsburg SoC subdriver.
- Intel Tiger Lake-H SoC subdriver.
- Qualcomm PM660 SoC subdriver.
- Renesas SH-PFC R8A774E1 subdriver.
Driver improvements:
- Linear improvement and cleanups of the Intel drivers for
Cherryview, Lynxpoint, Baytrail etc. Improved locking among
other things.
- Renesas SH-PFC has added support for RPC pins, groups, and
functions to r8a77970 and r8a77980.
- The newere Freescale (now NXP) i.MX8 pin controllers have
been modularized. This is driven by the Google Android
GKI initiative I think.
- Open drain support for pins on the Qualcomm IPQ4019.
- The Ingenic driver can handle both edges IRQ detection.
- A big slew of documentation fixes all over the place.
- A few irqchip template conversions by yours truly.
-----BEGIN PGP SIGNATURE-----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=mJgb
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of the pin control changes for the v5.9 kernel
series:
Core changes:
- The GPIO patch "gpiolib: Introduce for_each_requested_gpio_in_range()
macro" was put in an immutable branch and merged into the pinctrl
tree as well. We see these changes also here.
- Improved debug output for pins used as GPIO.
New drivers:
- Ocelot Sparx5 SoC driver.
- Intel Emmitsburg SoC subdriver.
- Intel Tiger Lake-H SoC subdriver.
- Qualcomm PM660 SoC subdriver.
- Renesas SH-PFC R8A774E1 subdriver.
Driver improvements:
- Linear improvement and cleanups of the Intel drivers for
Cherryview, Lynxpoint, Baytrail etc. Improved locking among other
things.
- Renesas SH-PFC has added support for RPC pins, groups, and
functions to r8a77970 and r8a77980.
- The newere Freescale (now NXP) i.MX8 pin controllers have been
modularized. This is driven by the Google Android GKI initiative I
think.
- Open drain support for pins on the Qualcomm IPQ4019.
- The Ingenic driver can handle both edges IRQ detection.
- A big slew of documentation fixes all over the place.
- A few irqchip template conversions by yours truly.
* tag 'pinctrl-v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (107 commits)
dt-bindings: pinctrl: add bindings for MediaTek MT6779 SoC
pinctrl: stmfx: Use irqchip template
pinctrl: amd: Use irqchip template
pinctrl: mediatek: fix build for tristate changes
pinctrl: samsung: Use bank name as irqchip name
pinctrl: core: print gpio in pins debugfs file
pinctrl: mediatek: add mt6779 eint support
pinctrl: mediatek: add pinctrl support for MT6779 SoC
pinctrl: mediatek: avoid virtual gpio trying to set reg
pinctrl: mediatek: update pinmux definitions for mt6779
pinctrl: stm32: use the hwspin_lock_timeout_in_atomic() API
pinctrl: mcp23s08: Use irqchip template
pinctrl: sx150x: Use irqchip template
dt-bindings: ingenic,pinctrl: Support pinmux/pinconf nodes
pinctrl: intel: Add Intel Emmitsburg pin controller support
pinctl: ti: iodelay: Replace HTTP links with HTTPS ones
Revert "gpio: omap: handle pin config bias flags"
pinctrl: single: Use fallthrough pseudo-keyword
pinctrl: qcom: spmi-gpio: Use fallthrough pseudo-keyword
pinctrl: baytrail: Use fallthrough pseudo-keyword
...
This became wide and scattered updates all over the sound tree as
diffstat shows: lots of (still ongoing) refactoring works in ASoC,
fixes and cleanups caught by static analysis, inclusive term
conversions as well as lots of new drivers. Below are highlights:
ASoC core:
* API cleanups and conversions to the unified mute_stream() call
* Simplify I/O helper functions
* Use helper macros to retrieve RTD from substreams
ASoC drivers:
* Lots of fixes and cleanups in Intel ASoC drivers
* Lots of new stuff: Freescale MQS and i.MX6sx, Intel KeemBay I2S,
Maxim MAX98360A and MAX98373 SoundWire, various Mediatek boards,
nVidia Tegra 186 and 210, RealTek RL6231, Samsung Midas and Aries
boards, TI J721e EVM
ALSA core:
* Minor code refacotring for SG-buffer handling
HD-audio:
* Generalization of mute-LED handling with LED classdev
* Intel silent stream support for HDMI
* Device-specific fixes: CA0132, Loongson-3
Others:
* Usual USB- and HD-audio quirks for various devices
* Fixes for echoaudio DMA position handling
* Various documents and trivial fixes for sparse warnings
* Conversion to adapt inclusive terms
-----BEGIN PGP SIGNATURE-----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=sy7n
-----END PGP SIGNATURE-----
Merge tag 'sound-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This became wide and scattered updates all over the sound tree as
diffstat shows: lots of (still ongoing) refactoring works in ASoC,
fixes and cleanups caught by static analysis, inclusive term
conversions as well as lots of new drivers. Below are highlights:
ASoC core:
- API cleanups and conversions to the unified mute_stream() call
- Simplify I/O helper functions
- Use helper macros to retrieve RTD from substreams
ASoC drivers:
- Lots of fixes and cleanups in Intel ASoC drivers
- Lots of new stuff: Freescale MQS and i.MX6sx, Intel KeemBay I2S,
Maxim MAX98360A and MAX98373 SoundWire, various Mediatek boards,
nVidia Tegra 186 and 210, RealTek RL6231, Samsung Midas and Aries
boards, TI J721e EVM
ALSA core:
- Minor code refacotring for SG-buffer handling
HD-audio:
- Generalization of mute-LED handling with LED classdev
- Intel silent stream support for HDMI
- Device-specific fixes: CA0132, Loongson-3
Others:
- Usual USB- and HD-audio quirks for various devices
- Fixes for echoaudio DMA position handling
- Various documents and trivial fixes for sparse warnings
- Conversion to adopt inclusive terms"
* tag 'sound-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (479 commits)
ALSA: pci: delete repeated words in comments
ALSA: isa: delete repeated words in comments
ALSA: hda/tegra: Add 100us dma stop delay
ALSA: hda: Add dma stop delay variable
ASoC: hda/tegra: Set buffer alignment to 128 bytes
ALSA: seq: oss: Serialize ioctls
ALSA: hda/hdmi: Add quirk to force connectivity
ALSA: usb-audio: add startech usb audio dock name
ALSA: usb-audio: Add support for Lenovo ThinkStation P620
Revert "ALSA: hda: call runtime_allow() for all hda controllers"
ALSA: hda/ca0132 - Fix AE-5 microphone selection commands.
ALSA: hda/ca0132 - Add new quirk ID for Recon3D.
ALSA: hda/ca0132 - Fix ZxR Headphone gain control get value.
ALSA: hda/realtek: Add alc269/alc662 pin-tables for Loongson-3 laptops
ALSA: docs: fix typo
ALSA: doc: use correct config variable name
ASoC: core: Two step component registration
ASoC: core: Simplify snd_soc_component_initialize declaration
ASoC: core: Relocate and expose snd_soc_component_initialize
ASoC: sh: Replace 'select' DMADEVICES 'with depends on'
...
- Prevent unnecessary timer softirq invocations by extending the tracking
of the next expiring timer in the timer wheel beyond the existing NOHZ
functionality. The tracking overhead at enqueue time is within the
noise, but on sensitive workloads the avoidance of the soft interrupt
invocation is a measurable improvement.
- The obligatory new clocksource driver for Ingenic X100 OST
- The usual fixes, improvements, cleanups and extensions for newer chip
variants all over the driver space.
-----BEGIN PGP SIGNATURE-----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=uJnp
-----END PGP SIGNATURE-----
Merge tag 'timers-core-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"Time, timers and related driver updates:
- Prevent unnecessary timer softirq invocations by extending the
tracking of the next expiring timer in the timer wheel beyond the
existing NOHZ functionality.
The tracking overhead at enqueue time is within the noise, but on
sensitive workloads the avoidance of the soft interrupt invocation
is a measurable improvement.
- The obligatory new clocksource driver for Ingenic X100 OST
- The usual fixes, improvements, cleanups and extensions for newer
chip variants all over the driver space"
* tag 'timers-core-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (28 commits)
timers: Recalculate next timer interrupt only when necessary
clocksource/drivers/ingenic: Add support for the Ingenic X1000 OST.
dt-bindings: timer: Add Ingenic X1000 OST bindings.
clocksource/drivers: Replace HTTP links with HTTPS ones
clocksource/drivers/nomadik-mtu: Handle 32kHz clock
clocksource/drivers/sh_cmt: Use "kHz" for kilohertz
clocksource/drivers/imx: Add support for i.MX TPM driver with ARM64
clocksource/drivers/ingenic: Add high resolution timer support for SMP/SMT.
timers: Lower base clock forwarding threshold
timers: Remove must_forward_clk
timers: Spare timer softirq until next expiry
timers: Expand clk forward logic beyond nohz
timers: Reuse next expiry cache after nohz exit
timers: Always keep track of next expiry
timers: Optimize _next_timer_interrupt() level iteration
timers: Add comments about calc_index() ceiling work
timers: Move trigger_dyntick_cpu() to enqueue_timer()
timers: Use only bucket expiry for base->next_expiry value
timers: Preserve higher bits of expiration on index calculation
clocksource/drivers/timer-atmel-tcb: Add sama5d2 support
...
There are three SoC families newly dded to the 32-bit and
64-bit Arm architecture code in the kernel this time:
- Daniel Palmer adds initial support for two chips made by MStar, a
taiwanese SoC manufacturer that became part of Mediatek in 2012. For
now, the added support is fairly minimal, with just two of its
Cortex-A7 based 32-bit camera chips getting support for a limited
set of on-chip peripherals.
- Lars Povlsen from Microchip adds support for their new Sparx5
family of ethernet switch chips using 64-bit Cortex-A53 cores.
These are descended from earlier VSC7xxx SparX and Ocelot chips
using 32-bit MIPS cores.
- Daniele Alessandrelli from Intel adds support for the new Keem Bay
SoC for computer vision, built around a Movidius VPU with Linux
running on Arm Cortex-A53 cores.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=Yy3D
-----END PGP SIGNATURE-----
Merge tag 'arm-newsoc-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull new ARM SoC support from Arnd Bergmann:
"There are three SoC families newly dded to the 32-bit and 64-bit Arm
architecture code in the kernel this time:
- Daniel Palmer adds initial support for two chips made by MStar, a
taiwanese SoC manufacturer that became part of Mediatek in 2012.
For now, the added support is fairly minimal, with just two of its
Cortex-A7 based 32-bit camera chips getting support for a limited
set of on-chip peripherals.
- Lars Povlsen from Microchip adds support for their new Sparx5
family of ethernet switch chips using 64-bit Cortex-A53 cores.
These are descended from earlier VSC7xxx SparX and Ocelot chips
using 32-bit MIPS cores.
- Daniele Alessandrelli from Intel adds support for the new Keem Bay
SoC for computer vision, built around a Movidius VPU with Linux
running on Arm Cortex-A53 cores"
* tag 'arm-newsoc-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (38 commits)
ARM: mstar: Correct the compatible string for pmsleep
dt-bindings: arm: mstar: remove the binding description for mstar,pmsleep
dt-bindings: mfd: syscon: add compatible string for mstar,msc313-pmsleep
ARM: mstar: Add reboot support
ARM: mstar: Add "pmsleep" node to base dtsi
ARM: mstar: Add PMU
ARM: mstar: Adjust IMI size for infinity3
ARM: mstar: Adjust IMI size for mercury5
ARM: mstar: Adjust IMI size of infinity
ARM: mstar: Add IMI SRAM region
dt-bindings: arm: mstar: Move existing MStar binding descriptions
dt-bindings: arm: mstar: Add binding details for mstar, pmsleep
ARM: mstar: Fix dts filename for 70mai midrive d08
ARM: mstar: Add dts for 70mai midrive d08
ARM: mstar: Add dts for msc313(e) based BreadBee boards
ARM: mstar: Add mercury5 series dtsis
ARM: mstar: Add infinity/infinity3 family dtsis
ARM: mstar: Add Armv7 base dtsi
ARM: mstar: Add binding details for mstar,l3bridge
ARM: mstar: Add machine for MStar/Sigmastar Armv7 SoCs
...
These are mostly cosmetic changes and minor bugfixes for the SoC
specific code, across the 32-bit at91, mvebu, davinci, samsung, and
omap platforms.
The main notable changes are for the Samsung Exynos platform, which
sees a rewrite of gpio handling and a change to restore and adds
a workaround for a problem with cpuidle support.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAl8j32AACgkQmmx57+YA
GNkoXA//RHlx49SRw9RXxrMHwPTq0L12R2YJsHoCw3GYmAi7MkLiSy+VsR0b8LON
vtflUwyVBDr6THlPYKqq/nBEaXQAHUd8xm5HQSwsgWdAcxwpvI2VQ8AFwCUIJOn5
I2a2kVNMTV7I7E1j64RpdoErtJiGlIFR6Yv7j1ENUBurTXT5KzGyugms1eHqSmNi
I1zVHzbvJji+vTxnDy2ooUyig04GP+8hY1/ZrwvStfruWZYckaeXCQIWvkExaqp5
pPnCTPrrnhKg44Nlco88QjoScz8vzGcLBXF0VpLhjD3J/IO/ySWuyBmRLZNS4VzU
c2zyQ6xnSLbC6QnQa6YYMwC6xVmYfzdudXORVM2sLAGsUH1XMV6zHbJ+dP6WGTjd
yfgkgr2bindbhSTuYKoyP5Km2MizW7ndTStpBKbdSR63kwF70POEAZPR9SZsoZcR
6gyaKNVqd3Xcuht3MfndR0WrYcTnzsz+EcioLP3AdQxfI2fM3l5NIqbtOt9txHi0
CcaVfK9k7sKGWkWHlcurrkB6kTDnlJYR6S1ZiiJMb+nriQAXkQjw+wuF6hb9qvIJ
sCKNFdVc8x+b0qf/CO1iss/H0s5dv2bzlXL/YgRUcpcLJ/zVEb1Cgl+Dx496pEwl
dEsMueRlfx9kvmZLkVJMHY5hTBDHaaDRHqmqaQpTcHdHDIwAGA4=
=IHpg
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Arnd Bergmann:
"These are mostly cosmetic changes and minor bugfixes for the SoC
specific code, across the 32-bit at91, mvebu, davinci, samsung, and
omap platforms.
The main notable changes are for the Samsung Exynos platform, which
sees a rewrite of gpio handling and a change to restore and adds a
workaround for a problem with cpuidle support"
* tag 'arm-soc-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: socfpga: PM: add missing put_device() call in socfpga_setup_ocram_self_refresh()
MAINTAINERS: arm/amlogic: add designated reviewers
ARM: davinci: dm646x-evm: Simplify error handling in 'evm_sw_setup()'
ARM: davinci: Fix trivial spelling
ARM: davinci: Replace HTTP links with HTTPS ones
ARM: s3c24xx: Replace HTTP links with HTTPS ones
ARM: orion/gpio: Make use of for_each_requested_gpio()
ARM: at91: Replace HTTP links with HTTPS ones
ARM: at91: pm: add missing put_device() call in at91_pm_sram_init()
ARM: rpc: Change blacklist to quirklist in ecode.c file
ARM: OMAP: Replace HTTP links with HTTPS ones
ARM: s3c24xx: leds: Convert to use GPIO descriptors
udc: lpc32xx: mark local function static
ARM: exynos: MCPM: Restore big.LITTLE cpuidle support
ARM: exynos: clear L310_AUX_CTRL_FULL_LINE_ZERO in default l2c_aux_val
As usual, there are many patches addressing minor issues in existing
DTS files, such as DTC warnings, or adding support for additional
peripherals.
There are three added SoCs in existing product families:
- Amazon:
Alpine v3 is a 16-core Cortex-A72 SoC from Amazon's Annapurna Labs,
otherwise known as AL73400 or first-generation Graviton, and following
the already supported Cortex-A1`5 and Cortex-A57 based Alpine chips.
This one is added together with the official Evaluation platform.
- Qualcomm:
The Snapdragon SDM630 platform is a family of mid-range mobile phone
chips from 2017 based on Cortex-A53 or Kryo 260 CPUs.
A total of five end-user products are added based on these, all
Android phones from Sony: Xperia 10, 10 Plus, XA2, XA2 Plus and
XA2 Ultra.
- Renesas:
RZ/G2H (r8a774e1) is currently the top model in the Renesas RZ/G
family, and apparently closely related to the RZ/G2N and RZ/G2M
models we already support but has a faster GPU and additional
on-chip peripherals.
It is added along with the HopeRun HiHope RZ/G2H development board
A small number of new boards for already supported SoCs also debut:
- Allwinner sunxi:
Only one new machine, revision v1.2 of the Pine64 PinePhone
(non-Android) smartphone, containing minor changes compared to
earlier versions.
- Amlogic Meson:
WeTek Core2 is an Amlogic S912 (GXM) based Set-top-box
- Aspeed:
EthanolX is AMD's EPYC data center rerence platform, using an
ASpeed AST2600 baseboard management controller.
- Mediatek:
Lenovo IdeaPad Duet 10.1" (kukui/krane) is a new Chromebook
based on the MT8183 (Helio P60t) SoC.
- Nvidia Tegra:
ASUS Google Nexus 7 and Acer Iconia Tab A500 are two Android
tablets from around 2012 using Tegra 3 and Tegra 2, respectively.
Thanks to PostmarketOS, these can now run mainline kernels
and become useful again.
The Jetson Xavier NX Developer Kit uses a SoM and carrier board
for the Tegra194, their latest 64-bit chip based on Carmel CPU
cores and Volta graphics.
- NXP i.MX:
Five new boards based on the 32-bit i.MX6 series are added:
The MYiR MYS-6ULX single-board computer, and four different
models of industrial computers from Protonic.
- Qualcomm:
MikroTik RouterBoard 3011 is a rackmounted router based on the
32-bit IPQ8064 networking SoC
Three older phones get added, the Snapdragon 808 (msm8992) based
Xiaomi Libra (Mi 4C) and Microsoft Lumia 950, originally running
Windows Phone, and the Snapdragon 810 (msm8994) based Sony
Xperia Z5.
- Renesas:
In addition to the HiHope RZ/G2H board mentioned above, we gain
support for board versions 3.0 and 4.0 of the earlier RZ/G2M and
RZ/G2N reference boards.
Beacon EmbeddedWorks adds another SoM+Carrier development board
for RZ/G2M.
- Rockchips:
Radxa Rock Pi N8 development board and the VMARC RK3288 SoM it
is based on, using the high-end 32-bit rk3288 SoC.
Notable updates to existing platforms are usually for added on-chip
peripherals, including:
- ASpeed AST2xxx (various)
- Allwinner (cpufreq, thermal, Pinephone touchscreen)
- Amlogic Meson (audio, gpu dvdfs, board updates)
- Arm Versatile
- Broadcom (board updates for switch ports, Raspberry pi clock updates)
- Hisilicon (various)
- Intel/Altera SoCFPGA (various)
- Marvell Armada 7xxx/8xxx (smmu)
- Marvell MMP (GPU on mmp2/mmp3)
- Mediatek mt8183 (USB, pericfg)
- NXP Layerscape (VPU, thermal, DSPI)
- NXP i.MX (VPU, bindings, board updates)
- Nvidia Tegra194 (GPU)
- Qualcomm (GPU, Interconnect, ...)
- Renesas R-Car (SPI, IPMMU, board updates)
- STMicroelectronics STM32 (various)
- Samsung Exynos (various)
- Socionext Uniphier (updates to serial, and pcie)
- TI K3 (serdes, usb3, audio, sd, chipid)
- TI OMAP (IPU/DSP remoteproc changes, dropping platform data)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=Tpj3
-----END PGP SIGNATURE-----
Merge tag 'arm-dt-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC DT updates from Arnd Bergmann:
"As usual, there are many patches addressing minor issues in existing
DTS files, such as DTC warnings, or adding support for additional
peripherals.
There are three added SoCs in existing product families:
- Amazon:
Alpine v3 is a 16-core Cortex-A72 SoC from Amazon's Annapurna Labs,
otherwise known as AL73400 or first-generation Graviton, and
following the already supported Cortex-A1`5 and Cortex-A57 based
Alpine chips. This one is added together with the official
Evaluation platform.
- Qualcomm:
The Snapdragon SDM630 platform is a family of mid-range mobile
phone chips from 2017 based on Cortex-A53 or Kryo 260 CPUs. A total
of five end-user products are added based on these, all Android
phones from Sony: Xperia 10, 10 Plus, XA2, XA2 Plus and XA2 Ultra.
- Renesas:
RZ/G2H (r8a774e1) is currently the top model in the Renesas RZ/G
family, and apparently closely related to the RZ/G2N and RZ/G2M
models we already support but has a faster GPU and additional
on-chip peripherals. It is added along with the HopeRun HiHope
RZ/G2H development board
A small number of new boards for already supported SoCs also debut:
- Allwinner sunxi:
Only one new machine, revision v1.2 of the Pine64 PinePhone
(non-Android) smartphone, containing minor changes compared to
earlier versions.
- Amlogic Meson:
WeTek Core2 is an Amlogic S912 (GXM) based Set-top-box
- Aspeed:
EthanolX is AMD's EPYC data center rerence platform, using an
ASpeed AST2600 baseboard management controller.
- Mediatek:
Lenovo IdeaPad Duet 10.1" (kukui/krane) is a new Chromebook based
on the MT8183 (Helio P60t) SoC.
- Nvidia Tegra:
ASUS Google Nexus 7 and Acer Iconia Tab A500 are two Android
tablets from around 2012 using Tegra 3 and Tegra 2, respectively.
Thanks to PostmarketOS, these can now run mainline kernels and
become useful again.
The Jetson Xavier NX Developer Kit uses a SoM and carrier board for
the Tegra194, their latest 64-bit chip based on Carmel CPU cores
and Volta graphics.
- NXP i.MX:
Five new boards based on the 32-bit i.MX6 series are added: The
MYiR MYS-6ULX single-board computer, and four different models of
industrial computers from Protonic.
- Qualcomm:
MikroTik RouterBoard 3011 is a rackmounted router based on the
32-bit IPQ8064 networking SoC
Three older phones get added, the Snapdragon 808 (msm8992) based
Xiaomi Libra (Mi 4C) and Microsoft Lumia 950, originally running
Windows Phone, and the Snapdragon 810 (msm8994) based Sony Xperia
Z5.
- Renesas:
In addition to the HiHope RZ/G2H board mentioned above, we gain
support for board versions 3.0 and 4.0 of the earlier RZ/G2M and
RZ/G2N reference boards. Beacon EmbeddedWorks adds another
SoM+Carrier development board for RZ/G2M.
- Rockchips:
Radxa Rock Pi N8 development board and the VMARC RK3288 SoM it is
based on, using the high-end 32-bit rk3288 SoC.
Notable updates to existing platforms are usually for added on-chip
peripherals, including:
- ASpeed AST2xxx (various)
- Allwinner (cpufreq, thermal, Pinephone touchscreen)
- Amlogic Meson (audio, gpu dvdfs, board updates)
- Arm Versatile
- Broadcom (board updates for switch ports, Raspberry pi clock updates)
- Hisilicon (various)
- Intel/Altera SoCFPGA (various)
- Marvell Armada 7xxx/8xxx (smmu)
- Marvell MMP (GPU on mmp2/mmp3)
- Mediatek mt8183 (USB, pericfg)
- NXP Layerscape (VPU, thermal, DSPI)
- NXP i.MX (VPU, bindings, board updates)
- Nvidia Tegra194 (GPU)
- Qualcomm (GPU, Interconnect, ...)
- Renesas R-Car (SPI, IPMMU, board updates)
- STMicroelectronics STM32 (various)
- Samsung Exynos (various)
- Socionext Uniphier (updates to serial, and pcie)
- TI K3 (serdes, usb3, audio, sd, chipid)
- TI OMAP (IPU/DSP remoteproc changes, dropping platform data)"
* tag 'arm-dt-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (605 commits)
arm64: dts: meson: odroid-n2: add jack audio output support
arm64: dts: meson: odroid-n2: enable audio loopback
ARM: dts: berlin: Align L2 cache-controller nodename with dtschema
arm64: dts: qcom: Add Microsoft Lumia 950 (Talkman) device tree
arm64: dts: qcom: Add Xiaomi Libra (Mi 4C) device tree
arm64: dts: qcom: msm8992: Add RPMCC node
arm64: dts: qcom: msm8992: Add PSCI support.
arm64: dts: qcom: msm8992: Add PMU node
arm64: dts: qcom: msm8992: Add BLSP2_UART2 and I2C nodes
arm64: dts: qcom: msm8992: Add SPMI PMIC arbiter device
arm64: dts: qcom: msm8992: Add a SCM node
arm64: dts: qcom: msm8992: Add a proper CPU map
arm64: dts: qcom: bullhead: Move UART pinctrl to SoC
arm64: dts: qcom: bullhead: Add qcom,msm-id
arm64: dts: qcom: msm8992: Fix SDHCI1
arm64: dts: qcom: msm8992: Modernize the DTS style
arm64: dts: qcom: Add support for Sony Xperia Z5 (SoMC Sumire-RoW)
arm64: dts: qcom: Move msm8994-smd-rpm contents to lg-bullhead.
arm64: dts: qcom: msm8994: Add support for SMD RPM
arm64: dts: qcom: msm8992: Add a label to rpm-requests
...
The compatible string for the pmsleep region has changed.
Update the MStar/Sigmastar v7 base dtsi with the new string.
Link: https://lore.kernel.org/r/20200729150748.1945589-4-daniel@0x0f.com
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
These are the latest device tree fixes for Arm SoCs:
- TI Keystone2 ethernet regressed after a driver change broke with
incorrect phy-mode in a board's DT source.
- A similar fix is needed for two i.MX boards that were missed in
an earlier bugfix.
- DT change for Armada 38x allowing to add the register needed to fix
NETA lockup when repeatedly switching speed.
- One fix on imx6qdl-icore pin muxing to get USB OTG_ID and SD card
detect work correctly.
- Two fixes for the Allwinner SoCs, one to relax the CMA allocation
ranges that were failing on older SoCs and one to fix Cedrus on the H6.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=qXc9
-----END PGP SIGNATURE-----
Merge tag 'arm-fixes-5.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc into master
Pull ARM SoC DT fixes from Arnd Bergmann:
"These are the latest device tree fixes for Arm SoCs:
- TI Keystone2 ethernet regressed after a driver change broke with
incorrect phy-mode in a board's DT source.
- A similar fix is needed for two i.MX boards that were missed in an
earlier bugfix.
- DT change for Armada 38x allowing to add the register needed to fix
NETA lockup when repeatedly switching speed.
- One fix on imx6qdl-icore pin muxing to get USB OTG_ID and SD card
detect work correctly.
- Two fixes for the Allwinner SoCs, one to relax the CMA allocation
ranges that were failing on older SoCs and one to fix Cedrus on the
H6"
* tag 'arm-fixes-5.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: dts: keystone-k2g-evm: fix rgmii phy-mode for ksz9031 phy
ARM: dts: armada-38x: fix NETA lockup when repeatedly switching speeds
ARM: dts: imx6qdl-icore: Fix OTG_ID pin and sdcard detect
ARM: dts: imx6sx-sabreauto: Fix the phy-mode on fec2
ARM: dts: imx6sx-sdb: Fix the phy-mode on fec2
arm64: dts: allwinner: h6: Fix Cedrus IOMMU usage
ARM: dts sunxi: Relax a bit the CMA pool allocation range
MStar v7 SoCs support reset by writing a magic value to a register
in the "pmsleep" area.
This adds a node for using the syscon reboot driver to trigger a reset.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds a node for the pmsleep area so that other
drivers can access registers contained within it.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
mercury5 family chips have 128KB of SRAM in the IMI region.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
All MStar v7 SoCs have an internal SRAM region that is between 64KB
(infinity2m) and 128KB(infinity3, mercury5).
The region is always at the same base address and is used for the
second stage loader (MStar IPL or u-boot SPL) and will be used for
the DDR self-refresh entry code within the kernel eventually.
This patch adds a 128KB region to the SoC and the minimum 64KB SRAM
region to the base dtsi. Families with more SRAM will override the
size in their family level dtsi.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Adds initial support for the 70mai midrive d08 dash camera.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
BreadBee is an opensource development board based on the
MStar msc313(e) SoC.
Hardware details, schematics and so on can be found at:
https://github.com/breadbee/breadbee
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This adds a family level dtsi for the mercury5 and then a
chip level dtsi for the ssc8336n chip.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This adds two family level dtsis for the infinity and infinity3
and then adds a chip level dtsi each for a chip in those families.
infinity3.dtsi includes infinity.dtsi as these SoCs share most of
their memory map and we would have a lot of duplication otherwise.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Adds initial dtsi for the base MStar/Sigmastar Armv7 SoCs.
These SoCs have very similar memory maps and this will avoid
duplicating nodes across multiple dtsis.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Enable the second EHCI controller on the AST2600. Also add a line-name
for the GPIO that controls power to the USB port.
The power control is in place to allow the port to be disabled, for
those that are worried about rogue USB sticks.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Enable the second EHCI controller on the AST2600. Also add a line-name
for the GPIO that controls power to the USB port.
The power control is in place to allow the port to be disabled, for
those that are worried about rogue USB sticks.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Rainier uses the P10 processor so the OCC binding should reflect that.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add the four SPI masters on each CFAM. Each master has four 128KB EEPROM
devices attached to it.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Adding pca9552 exposes the presence detect lines for the cards and
tca9554 exposes the presence details for the cards.
Signed-off-by: Jet Li <Jet.Li@ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Initial introduction of AMD EthanolX platform equipped with an
Aspeed ast2500 BMC manufactured by AMD.
AMD EthanolX platform is an AMD customer reference board with an
Aspeed ast2500 BMC manufactured by AMD.
This adds AMD EthanolX device tree file including the flash layout
used by EthanolX BMC machines.
Signed-off-by: Supreeth Venkatesh <supreeth.venkatesh@amd.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
We have a 4-bus mux whose output is selected by two GPIO inputs. Wire it
up in the devicetree and ensure the output is enabled by hogging the
appropriate line.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Since commit bcf3440c6d ("net: phy: micrel: add phy-mode support for the
KSZ9031 PHY") the networking is broken on keystone-k2g-evm board.
The above board have phy-mode = "rgmii-id" and it is worked before because
KSZ9031 PHY started with default RGMII internal delays configuration (TX
off, RX on 1.2 ns) and MAC provided TX delay by default.
After above commit, the KSZ9031 PHY starts handling phy mode properly and
enables both RX and TX delays, as result networking is become broken.
Fix it by switching to phy-mode = "rgmii-rxid" to reflect previous
behavior.
Fixes: bcf3440c6d ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- new board: WeTek Core2
- audio playback support on more boards
- add GPU DVFS
-----BEGIN PGP SIGNATURE-----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=ibOR
-----END PGP SIGNATURE-----
Merge tag 'amlogic-dt64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/dt
arm64: dts: amlogic: updates for v5.9 (round 2)
- new board: WeTek Core2
- audio playback support on more boards
- add GPU DVFS
* tag 'amlogic-dt64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
arm64: dts: amlogic: meson-g12: add the Mali OPP table and use DVFS
arm64: dts: amlogic: meson-gxm: add the Mali OPP table and use DVFS
arm64: dts: amlogic: meson-gx: add the Mali-450 OPP table and use DVFS
arm64: dts: meson: add support for the WeTek Core 2
dt-bindings: arm: amlogic: add support for the WeTek Core 2
arm64: dts: meson: add audio playback to khadas-vim3l
arm64: dts: meson: add audio playback to odroid-c4
arm64: dts: meson: update spifc node name on Khadas VIM3/VIM3L
ARM: dts: meson: Align L2 cache-controller nodename with dtschema
arm64: dts: meson-gxl-s805x: reduce initial Mali450 core frequency
arm64: dts: meson: add missing gxl rng clock
soc: amlogic: meson-gx-socinfo: Fix S905X3 and S905D3 ID's
Link: https://lore.kernel.org/r/7h8sf8671u.fsf@baylibre.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- DT change for Armada 38x allowing to add the register needed to fix
NETA lockup when repeatedly switching speed.
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCXxqaPwAKCRALBhiOFHI7
1YANAKCEUNj0n91jslQNBACKuB7a79Ag3ACbB/hWOsGi+BVNlDy5mnXeoT5ZEd0=
=GJyb
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu into arm/fixes
mvebu fixes for 5.8 (part 1)
- DT change for Armada 38x allowing to add the register needed to fix
NETA lockup when repeatedly switching speed.
* tag 'mvebu-fixes-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
ARM: dts: armada-38x: fix NETA lockup when repeatedly switching speeds
- Fix the reg-init PHY for the dlink-dns327l (Armada 370)
- Replace HTTP links with HTTPS one in device tree of the Excito
Bubba B3 (Kirkwood)
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCXxqh0gAKCRALBhiOFHI7
1R9KAJ0TuEHE0boReOUAhpAlfYIqYeR5QQCfUuD/p2aoTSfNNyctLQsHmnjBYao=
=PzgE
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu into arm/dt
mvebu dt for 5.9 (part 1)
- Fix the reg-init PHY for the dlink-dns327l (Armada 370)
- Replace HTTP links with HTTPS one in device tree of the Excito
Bubba B3 (Kirkwood)
* tag 'mvebu-dt-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
ARM: dts: dlink-dns327l: fix reg-init PHY
ARM: dts: kirkwood: Replace HTTP links with HTTPS ones
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
To support the change in "phy: armada-38x: fix NETA lockup when
repeatedly switching speeds" we need to update the DT with the
additional register.
Fixes: 14dc100b44 ("phy: armada38x: add common phy support")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Enable pwm_tacho device for fan control and monitoring in Wedge40.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Enable ADC controller and corresponding voltage sensoring channels for
Wedge40.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Disable i2c bus #9, #10 and #13 as these i2c controllers are not used on
Wedge40.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Create all the i2c switches in device tree and use aliases to assign
child channels with consistent bus numbers.
Besides, "i2c-mux-idle-disconnect" is set for all the i2c switches to
avoid potential conflicts when multiple devices (beind the switches)
use the same device address.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The GPIO on Q0 is used for resetting the CFAM of the processor that the
ASPEED master is connected to.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The GPIO on Q0 is used for resetting the CFAM of the processor that the
ASPEED master is connected to.
The signal is wired as active high on the first pass systems.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
- Add the high resolution support for SMP/SMT on the Ingenic timer (Zhou Yanjie)
- Add support for i.MX TPM driver with ARM64 (Anson Huang)
- Fix typo by replacing KHz to kHz (Geert Uytterhoeven)
- Add 32kHz support by setting the minimum ticks to 5 on Nomadik MTU (Linus Walleij)
- Replace HTTP links with HTTPS ones for security reasons (Alexander A. Klimov)
- Add support for the Ingenic X1000 OST (Zhou Yanjie)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAl8ZqeUACgkQqDIjiipP
6E9tawf/UGUhEfB+VmH9w60NJlM0fC5a/TjVOb4yMjTZjjdyd4zMBHemF+dqMNnw
wTr+S8U9QfvP4BDgg1hWV+vhAwxz2xkhR0cGtOQjck5322vZglGSmAVqTCAlQMoZ
LNm98XeUYYVNMB+/+BHkf8F/nHV9vRo8sJg7UnvX/6RCykXFYXVP+P8LfkAU1MPt
8vaRPCcyGnYXrgjDYY5M5qYudLNpFPrzr1yJDWdwWUliwH3T1X1FNogTdUo955qk
wM+Hb4yPRuRufM+yATPsRedQypZFpoWFObuEMD2FaIw/LZVxV7D1tmw5KhL2V1tZ
XSzNiJDEgri/4LaVzXKP7sVlQlZfDQ==
=DXTp
-----END PGP SIGNATURE-----
Merge tag 'timers-v5.9' of https://git.linaro.org/people/daniel.lezcano/linux into timers/core
Pull clock event/surce driver changes from Daniel Lezcano:
- Add sama5d2 support and rework the 32kHz clock handling (Alexandre Belloni)
- Add the high resolution support for SMP/SMT on the Ingenic timer (Zhou Yanjie)
- Add support for i.MX TPM driver with ARM64 (Anson Huang)
- Fix typo by replacing KHz to kHz (Geert Uytterhoeven)
- Add 32kHz support by setting the minimum ticks to 5 on Nomadik MTU (Linus Walleij)
- Replace HTTP links with HTTPS ones for security reasons (Alexander A. Klimov)
- Add support for the Ingenic X1000 OST (Zhou Yanjie)
SOM and it's Rock Pi N8 icarnation. This brings some arm64 dts-changes
with it as the underlying Dalang carrier board is shared by both
an arm32 rk3288 SOM and an arm64 rk3399 SOM (Rock Pi N10).
Other than that rk3288 gets its ohci node added that only works
on the fixed rk3288w variant of the soc and some asorted fixes
and improvements for dt-binding-check.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAl8YzOAQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgY9aB/0folCAovUA97bILQR/62PspVGR1i/S2GJe
sQqKuWDyBtJNM3IYNVMd/AtcrP+U0ZD4MX6TKbabs+ZuIc4EksXRroMTMm2azme1
rOrQuGSKcdhPobJOHlpbSC/QPWWi5GGGWDnwXY8T68NedeYLP/o8sOmZQtUi80R9
ueP5ZwiviwMrVzRITPb8sB89WEyRqaas2H0fc/4OjGRY/jeTKwCk9sP/JytA6gUB
/GXn+uUk5WcRkekujBi1LVi4BIhm7PMW9kM1AHWAV6+2Yd8uFyG4ut9MB7SmaQt8
QfEoPpLvQicpZCVB3VFOPJ38z4YuOXsqo85u8T3ZkgpLdInoa/J9
=GUhq
-----END PGP SIGNATURE-----
Merge tag 'v5.9-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt
Biggest part is the addition of the rk3288 variant of the VMARC
SOM and it's Rock Pi N8 icarnation. This brings some arm64 dts-changes
with it as the underlying Dalang carrier board is shared by both
an arm32 rk3288 SOM and an arm64 rk3399 SOM (Rock Pi N10).
Other than that rk3288 gets its ohci node added that only works
on the fixed rk3288w variant of the soc and some asorted fixes
and improvements for dt-binding-check.
* tag 'v5.9-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Add PCIe for RockPI N10
ARM: dts: rockchip: Add HDMI out for RockPI N8/N10
ARM: dts: rockchip: Add USB for RockPI N8/N10
ARM: dts: rockchip: Add usb host0 ohci node for rk3288
ARM: dts: rockchip: Fix VBUS on rk3288-vyasa
ARM: dts: rockchip: Add Radxa Rock Pi N8 initial support
ARM: dts: rockchip: Add VMARC RK3288 SOM initial support
dt-bindings: arm: rockchip: Add Rock Pi N8 binding
arm64: dts: rk3399pro: vmarc-som: Move common properties into Carrier
arm64: dts: rk3399pro: vmarc-som: Move supply regulators into Carrier
arm64: dts: rk3399pro: vmarc-som: Fix sorting nodes, properties
ARM: dts: rockchip: dalang-carrier: Move i2c nodes into SOM
ARM: dts: rockchip: Add 'arm,pl330-periph-burst' for dmac
ARM: dts: rockchip: Add marvell BT irq config
ARM: dts: rockchip: rename label and nodename pinctrl subnodes that end with gpio
Link: https://lore.kernel.org/r/2472314.kD9Egx1jfM@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This enables the audio SRAM, DMA engine, I2S interface, and codec, hooks
them together and adds a audio-graph-card instance.
It also removes the jack gpios from the gpio-keys instance, because the
audio jack driver registers an input device.
Link: https://lore.kernel.org/r/20200718205019.184927-10-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This memory is region is where the two-channel audio DMA can pump sound
samples into the SSPA's internal FIFO.
Link: https://lore.kernel.org/r/20200718205019.184927-6-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The ACGR register is at the offset of 0x1024, beyond the 4k originally
assigned to the MPMU range.
Link: https://lore.kernel.org/r/20200718205019.184927-5-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The power management unit, described by the soc_clocks node, controls the
power to the peripherals by the means of power domains with a single
cell -- the domain number.
Link: https://lore.kernel.org/r/20200718205019.184927-4-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
On the XO-1.75, this node represents a bus interface that operates in slave
mode and thus is only able to accommodate a single subnode; no address
cells are necessary.
The Documentation/devicetree/bindings/spi/spi-controller.yaml binding
prefers that we drop the property instead of setting it to zero.
This fixes a DT validation error:
arch/arm/boot/dts/mmp2-olpc-xo-1-75.dt.yaml: spi@d4037000:
{ ... } is valid under each of {'required': ['spi-slave']},
{'required': ['#address-cells']}
We also need to drop #size-cells:
arch/arm/boot/dts/mmp2-olpc-xo-1-75.dt.yaml: spi@d4037000:
'#address-cells' is a dependency of '#size-cells'
Link: https://lore.kernel.org/r/20200718205019.184927-3-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
mmp2-olpc-xo-1-75.dt.yaml: camera_i2c: $nodename:0:
'camera_i2c' does not match '^i2c(@.*)?'
mmp2-olpc-xo-1-75.dt.yaml: camera_i2c: 'sda-gpios' is a required property
mmp2-olpc-xo-1-75.dt.yaml: camera_i2c: 'scl-gpios' is a required property
The "gpios" property actually was documented as deprecated, but got dropped
in commit 0175ce4a58 ("dt-bindings: i2c: Convert i2c-gpio binding to
json-schema"). It's probably best kept forgotten though.
Link: https://lore.kernel.org/r/20200718205019.184927-2-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Highlights:
----------
MCU part:
-Enable stmpe811 on stm32f429
-Enable l3gd20-gyro on stm32f429
-Enable panel-ilitek-9341 on stm32f429
-Fixes for yaml validation (leds, nodes names,
remove useless bindings ...)
-Add stm32xxx compatibles for syscon nodes
MPU part:
-Add support for usb role switch to dwc2
-Add stm32xxx compatibles for syscon nodes
-Update uart4 pin configuration for low power mode
used by dkx and ed1 ST boards
-Fix uart nodes ordering and uart7_pins_a comments
-Add the support of uart instances available on STM32MP157 boards:
- usart3 on stm32mp157c-ev1, stm32mp157a-dk1, and stm32mp157c-dk2
- uart7 on stm32mp157a-dk1 and stm32mp157c-dk2
- usart2 on stm32mp157c-dk2
-Configure I2C5 on stm32mp15 DK boards
-----BEGIN PGP SIGNATURE-----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=ga5j
-----END PGP SIGNATURE-----
Merge tag 'stm32-dt-for-v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/dt
STM32 DT updates for v5.9, round 1
Highlights:
----------
MCU part:
-Enable stmpe811 on stm32f429
-Enable l3gd20-gyro on stm32f429
-Enable panel-ilitek-9341 on stm32f429
-Fixes for yaml validation (leds, nodes names,
remove useless bindings ...)
-Add stm32xxx compatibles for syscon nodes
MPU part:
-Add support for usb role switch to dwc2
-Add stm32xxx compatibles for syscon nodes
-Update uart4 pin configuration for low power mode
used by dkx and ed1 ST boards
-Fix uart nodes ordering and uart7_pins_a comments
-Add the support of uart instances available on STM32MP157 boards:
- usart3 on stm32mp157c-ev1, stm32mp157a-dk1, and stm32mp157c-dk2
- uart7 on stm32mp157a-dk1 and stm32mp157c-dk2
- usart2 on stm32mp157c-dk2
-Configure I2C5 on stm32mp15 DK boards
* tag 'stm32-dt-for-v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (38 commits)
ARM: dts: stm32: enable usb-role-switch on USB OTG on stm32mp15xx-dkx
ARM: dts: stm32: Add compatibles for syscon for stm32mp151
ARM: dts: stm32: Add compatibles for syscon for stm32h743
ARM: dts: stm32: Add compatibles for syscon for stm32f746
ARM: dts: stm32: Add compatibles for syscon for stm32f426
dt-bindings: arm: stm32: Add compatibles for syscon nodes
ARM: dts: stm32: Fix spi4 pins in stm32mp15-pinctrl
ARM: dts: stm32: configure i2c5 support on stm32mp15xx-dkx
ARM: dts: stm32: add usart2 node to stm32mp157c-dk2
ARM: dts: stm32: add uart7 support to stm32mp15xx-dkx boards
ARM: dts: stm32: add usart3 node to stm32mp157c-ev1
ARM: dts: stm32: add usart3 node to stm32mp15xx-dkx boards
ARM: dts: stm32: add usart2, usart3 and uart7 pins in stm32mp15-pinctrl
ARM: dts: stm32: cosmetic updates in stm32mp15-pinctrl
ARM: dts: stm32: fix uart7_pins_a comments in stm32mp15-pinctrl
ARM: dts: stm32: fix uart nodes ordering in stm32mp15-pinctrl
ARM: dts: stm32: Update UART4 pin states on stm32mp15xx-dkx
ARM: dts: stm32: Update pin states for uart4 on stm32mp157c-ed1
ARM: dts: stm32: update uart4 pin configuration for low power on stm32mp157
dt-bindings: usb: dwc2: Fix issues for stm32mp15x SoC
...
Link: https://lore.kernel.org/r/8a9bb27b-fc08-126a-11f7-01354e8577e1@st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
1. Enable Bluetooth on Artik5 (Exynos3250).
2. Enable accelerometer on Aries boards (Samsung Galaxy S family,
S5Pv210); multiple fixes.
3. Fix highest frequencies on Exynos5800.
4. Fix rare USB instability on Odroid XU3 family (Exynos5422).
5. Minor DTS fixes and adjustments with dtschema.
-----BEGIN PGP SIGNATURE-----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=k3pO
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v5.9
1. Enable Bluetooth on Artik5 (Exynos3250).
2. Enable accelerometer on Aries boards (Samsung Galaxy S family,
S5Pv210); multiple fixes.
3. Fix highest frequencies on Exynos5800.
4. Fix rare USB instability on Odroid XU3 family (Exynos5422).
5. Minor DTS fixes and adjustments with dtschema.
* tag 'samsung-dt-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Replace HTTP links with HTTPS ones
ARM: dts: exynos: Disable frequency scaling for FSYS bus on Odroid XU3 family
ARM: dts: exynos: Define fixed regulators in root node for consistency in SMDK5420
ARM: dts: exynos: Define fixed regulators in root node for consistency in Arndale
ARM: dts: exynos: Define fixed regulators in root node for consistency in Origen
ARM: dts: exynos: Remove DMA controller bus node name to fix dtschema warnings
ARM: dts: exynos: Fix missing empty reg/ranges property regulators on Trats
ARM: dts: exynos: Align L2 cache-controller nodename with dtschema
ARM: dts: s5pv210: Correct BCM4329 bluetooth node
ARM: dts: s5pv210: Add BMA023 accelerometer support to Aries
ARM: dts: s5pv210: Add support for GP2A light sensor on Aries
ARM: dts: s5pv210: Correct fuelgauge definition on Aries
ARM: dts: s5pv210: Add interrupt-controller property to gph3
ARM: dts: exynos: Enable Bluetooth support for Artik5 board
ARM: dts: exynos: Extend all Exynos5800 A15's OPPs with max voltage data
Link: https://lore.kernel.org/r/20200721180900.13844-2-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add QFPROM and ethernet for ipq8064 and a new DTS for the MikroTik
RB3011 using the same platform.
-----BEGIN PGP SIGNATURE-----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=wWXD
-----END PGP SIGNATURE-----
Merge tag 'qcom-dts-for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt
Qualcomm ARM dts updates for v5.9
Add QFPROM and ethernet for ipq8064 and a new DTS for the MikroTik
RB3011 using the same platform.
* tag 'qcom-dts-for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
ARM: dts: qcom: add qfprom definition to ipq806x
ARM: dts: qcom: Add MikroTik RB3011
ARM: dts: qcom: add ethernet definitions to ipq8064
Link: https://lore.kernel.org/r/20200721045032.3430395-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
support, including:
- CPUFreq / Thermal throttling support for the H5
- Touchscreen support for the Pinephone
- New boards: PinePhone v1.2
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXxWlZAAKCRDj7w1vZxhR
xft/AQCaR2CkyOVyK32yPUX0ZF2nS+LYzalJIUpOuLhy37GQVwEA+vlQTa7fKdtW
4IX58peBkRD8FwTszrwR/tImDPd8Rwg=
=z8pA
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
Our usual number of patches to improve the Allwinner Device Tree
support, including:
- CPUFreq / Thermal throttling support for the H5
- Touchscreen support for the Pinephone
- New boards: PinePhone v1.2
* tag 'sunxi-dt-for-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: h5: bananapi-m2-plus-v1.2: Tie in CPU OPPs
arm64: dts: allwinner: h5: libretech-all-h3-cc: Tie in CPU OPPs
arm64: dts: allwinner: h5: Add CPU Operating Performance Points table
arm64: dts: allwinner: h5: Add trip and cooling maps to CPU thermal zones
arm64: dts: allwinner: h5: Add clock to CPU cores
ARM: dts: sunxi: bananapi-m2-plus-v1.2: Fix CPU supply voltages
ARM: dts: sunxi: bananapi-m2-plus-v1.2: Add regulator supply to all CPU cores
ARM: dts: sunxi: libretech-all-h3-cc: Add regulator supply to all CPU cores
arm64: dts: sun50i-pinephone: dldo4 must not be >= 1.8V
arm64: dts: allwinner: Add support for PinePhone revision 1.2
dt-bindings: arm: sunxi: Add PinePhone 1.2 bindings
arm64: dts: sun50i-a64-pinephone: Add touchscreen support
arm64: dts: sun50i-a64-pinephone: Enable LCD support on PinePhone
ARM: dts: orange-pi-zero-plus2: add leds configuration
ARM: dts: orange-pi-zero-plus2: enable USB OTG port
Link: https://lore.kernel.org/r/fa48ffcb-3404-41bb-b065-a16717cf5688.lettre@localhost
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
just a single patch fixing up the node names for schema.
-----BEGIN PGP SIGNATURE-----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=xBG2
-----END PGP SIGNATURE-----
Merge tag 'versatile-for-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into arm/dt
Versatile DTS changes for the v5.9 kernel cycle, essentially
just a single patch fixing up the node names for schema.
* tag 'versatile-for-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: dts: arm-realview: Align L2 cache-controller nodename with dtschema
Link: https://lore.kernel.org/r/CACRpkdbkM9ZmuG2FnBmO7upcJfnqq2oSLDCFDXC5b3K+dtps9Q@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- New board support: Protonic PRTI6Q/WD2/VT7/RVT and MYiR MYS-6ULX SBC.
- Update IIM, OCOTP and SD/MMC device node name to match .yaml bindings.
- Make tempmon node as child of anatop node according to hardware
architecture.
- The vf610-zii device update: configure fiber port to 1000BaseX, add
switch watchdog, MDIO speed and preamble.
- A series from Fabio Estevam to update imx6qdl-sabresd and
imx6q-tbs2910 for using MDIO node and reset-assert-us.
- Align L2 cache-controller device node name with .yaml schema.
- Enable SATA support for imx6qp-sabreauto and imx6qp-sabresd board.
- A series of patches from Shengjiu Wang to enable various audio
support on i.MX6 devices.
- Add Gateworks System Controller support for imx6qdl-gw devices.
- Change default #pwm-cells setting to <3> in the SoC dtsi files.
- Other small random changes.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl8VVgcUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM7azwf+KzAukegArKtAmsbAnYNKYztXXifW
6Hc3+hv2mfUtsGfHPSUJJ5MhEW52xAbcXnYETUkmoWe1W1zIxrNNWvBUm4nPF5os
0cO8tjk4cE4CYDnsl8sBSqT55sd3ke61I+j9q0NAQNyX9OlmZ3kfm8yw0yIsxTKp
/FzoLmOeRzhVKHdZczuJ9Ts4kFyf3XtQrrN1UTbu715KdIbbsrJtXQ74ADBCnjfX
8RUm3Y5XIaPcF4z2U8reMsbHCF120ENIfGwFRNo/Odx+1OVo1IrDB1+f/SP9ZP0T
6+iKvfSS4RavzB1tvLdJ2/911t7qtqsneU33kwQKL0wrFZsT4ih42uBfpw==
=1hHY
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX device tree update for 5.9:
- New board support: Protonic PRTI6Q/WD2/VT7/RVT and MYiR MYS-6ULX SBC.
- Update IIM, OCOTP and SD/MMC device node name to match .yaml bindings.
- Make tempmon node as child of anatop node according to hardware
architecture.
- The vf610-zii device update: configure fiber port to 1000BaseX, add
switch watchdog, MDIO speed and preamble.
- A series from Fabio Estevam to update imx6qdl-sabresd and
imx6q-tbs2910 for using MDIO node and reset-assert-us.
- Align L2 cache-controller device node name with .yaml schema.
- Enable SATA support for imx6qp-sabreauto and imx6qp-sabresd board.
- A series of patches from Shengjiu Wang to enable various audio
support on i.MX6 devices.
- Add Gateworks System Controller support for imx6qdl-gw devices.
- Change default #pwm-cells setting to <3> in the SoC dtsi files.
- Other small random changes.
* tag 'imx-dt-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (43 commits)
ARM: dts: vf610-zii-ssmb-spu3: Add node for switch watchdog
ARM: dts: vf610-zii-ssmb-dtu: Add no-sdio/no-sd properties
ARM: dts: imx6q-tbs2910: Pass reset-assert-us
ARM: dts: imx6q-tbs2910: Add an mdio node
ARM: dts: imx6qdl-sabresd: Pass reset-assert-us
ARM: dts: imx6qdl-sabresd: Add an mdio node
ARM: dts: imx6qdl-gw: add Gateworks System Controller support
ARM: dts: imx6ull: add MYiR MYS-6ULX SBC
ARM: dts: vf610-zii-spb4: Add node for switch watchdog
ARM: dts: colibri-imx6: remove pinctrl-names orphan
ARM: dts: imx: default to #pwm-cells = <3> in the SoC dtsi files
ARM: dts: vf610-zii-scu4-aib: Configure fibre ports to 1000BaseX
ARM: dts: vf610-zii-dev-rev-c: Configure fiber port to 1000BaseX
ARM: dts: ZII: update MDIO speed and preamble
ARM: dts: vfxxx: Add node for CAAM
ARM: dts: imx6qp-sabresd: enable sata
ARM: dts: imx6qp-sabreauto: enable sata
ARM: dts: add Protonic RVT board
ARM: dts: add Protonic VT7 board
ARM: dts: add Protonic WD2 board
...
Link: https://lore.kernel.org/r/20200720085536.24138-3-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- A couple of FEC2 phy-mode fixes on imx6sx-sabreauto and imx6sx-sdb
board.
- One fix on imx6qdl-icore pin muxing to get USB OTG_ID and SD card
detect work correctly.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl8VFn0UHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM52gQf+OGrSQq1t77ltL5EKeeV8f+PCu7UP
X7I2IJY+9FIYA1wuu0/AuhHaJ9NR0hN2mZVT+ktmxIDMVuHZJpAuHRfGp7anfVKr
vo1JgT9CbVZ/kD0n5a6TN28Kb7DVkIM4QGcEJuCD2mb1UJarlVX8YHg9Otv7b26p
3arPLR8eocPh2jNNdYnwSoZ8Li7Dm1SQloRAoCJOHAgAuSAdhG15rJBG70zX0F7d
QEWu6tNjN8FSrWeT1GLlzywYxGp1t592yuUpKAoppuJgxyUPIYA15vRB0d/KRqUL
CWYrDNh/dAvafI9HfeQQK5BjQhW58gy2c38s+bR9iPGoy88GzZiy+AatYQ==
=NlnX
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.8, round 3:
- A couple of FEC2 phy-mode fixes on imx6sx-sabreauto and imx6sx-sdb
board.
- One fix on imx6qdl-icore pin muxing to get USB OTG_ID and SD card
detect work correctly.
* tag 'imx-fixes-5.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6qdl-icore: Fix OTG_ID pin and sdcard detect
ARM: dts: imx6sx-sabreauto: Fix the phy-mode on fec2
ARM: dts: imx6sx-sdb: Fix the phy-mode on fec2
Link: https://lore.kernel.org/r/20200720040148.GA20462@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
were failing on older SoCs and one to fix Cedrus on the H6.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXxWlyQAKCRDj7w1vZxhR
xcNtAQDO2rSFHGpQsUE/MCRxMqd2c2OQ9zpovRnirnyJqLCPEwD/b8GAi9tfJksM
lmghSQnByq6Sqm9UA/i6jjLfz//4iQg=
=JoYD
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes
Two fixes for the Allwinner SoCs, one to relax the CMA allocation ranges that
were failing on older SoCs and one to fix Cedrus on the H6.
* tag 'sunxi-fixes-for-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: h6: Fix Cedrus IOMMU usage
ARM: dts sunxi: Relax a bit the CMA pool allocation range
Link: https://lore.kernel.org/r/e24f0608-6a4f-4163-b99e-a5f48e796184.lettre@localhost
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds support to enable HDMI out for
N10 and N8 combinations SBCs.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Link: https://lore.kernel.org/r/20200720110230.367985-2-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Radxa dalang carrier board has 2x USB 2.0 and 1x USB 3.0
ports.
This patch adds support to enable all these USB ports for
N10 and N8 combinations SBCs.
Note that the USB 3.0 port on RockPI N8 combination works
as USB 2.0 OTG since it is driven from RK3288.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20200720110230.367985-1-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
rk3288 and rk3288w have a usb host0 ohci controller.
Although rk3288 ohci doesn't actually work on hardware, but
rk3288w ohci can work well.
So add usb host0 ohci node in rk3288 dtsi and boards
can then enable it if supported.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Cc: William Wu <william.wu@rock-chips.com>
Link: https://lore.kernel.org/r/20200720105846.367776-1-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
[nsekhar@ti.com: drop obsolete hawkboard.org URL completeley
fixup subject line prefix]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Now that USB OTG driver supports usb role switch by overriding PHY input
signals (A-Valid, B-Valid and Vbus-Valid), enable it on stm32mp15xx-dkx.
dr_mode needn't to be forced to Peripheral anymore, it is set to OTG in
SoC device tree.
USB role (USB_ROLE_NONE, USB_ROLE_DEVICE, USB_ROLE_HOST) will be provided
by STUSB1600 Type-C controller driver.
This patch depends on "Add STUSB160x Type-C port controller support"
series, which is under review.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Syscon nodes needs at least 2 compatibles to be compliant why yaml documentation.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Syscon nodes needs at least 2 compatibles to be compliant why yaml documentation.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Syscon nodes needs at least 2 compatibles to be compliant why yaml documentation.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Syscon nodes needs at least 2 compatibles to be compliant why yaml documentation.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Move spi4_pins_a nodes from pinctrl_z to pinctrl as the associated pins
are not in BANK Z.
Fixes: 498a701498 ("ARM: dts: stm32: Add missing pinctrl entries for STM32MP15")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Configure I2C5 on stm32mp15 DK boards. It's available and can be used on:
- Arduino connector
- GPIO expansion connector
Keep it disabled by default, so the pins are kept in their initial state to
lower power consumption. This way they can also be used as GPIO.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Adds the usart2 node to stm32mp157c-dk2 board. usart2 pins are connected
to Bluetooth component. usart2 is disabled by default.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Adds uart7 node to stm32mp15xx-dkx and uart7 alias to stm32mp157a-dk1 and
stm32mp157c-dk2 boards. uart7 pins are connected to Arduino connector.
uart7 is disabled by default.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Adds the usart3 node to stm32mp157c-ev1 board. usart3 pins are connected to
GPIO Expansion connector. usart3 is disabled by default.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Adds usart3 node to stm32mp15xx-dkx and usart3 alias to stm32mp157a-dk1
and stm32mp157c-dk2 boards. usart3 pins are connected to GPIO Expansion
connector. usart3 is disabled by default.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Adds usart2_pins_c, usart3_pins_b, usart3_pins_c and uart7_pins_c pins
configurations in stm32mp15-pinctrl.
- usart2_pins_c pins are connected to Bluetooth chip on dk2 board.
- usart3_pins_b pins are connected to GPIO expansion connector on evx board.
- usart3_pins_c pins are connected to GPIO expansion connector on dkx board.
- uart7_pins_c pins are connected to Arduino Uno connector on dkx board.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Use tabs where possible and remove multiple blanks lines.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The Bananapi M2+ uses a GPIO line to change the effective resistance of
the CPU supply regulator's feedback resistor network. The voltages
described in the device tree were given directly by the vendor. This
turns out to be slightly off compared to the real values.
The updated voltages are based on calculations of the feedback resistor
network, and verified down to three decimal places with a multi-meter.
Fixes: 6eeb4180d4 ("ARM: dts: sunxi: h3-h5: Add Bananapi M2+ v1.2 device trees")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200717160053.31191-4-wens@kernel.org
The device tree currently only assigns the a supply for the first CPU
core, when in reality the regulator supply is shared by all four cores.
This might cause an issue if the implementation does not realize the
sharing of the supply.
Assign the same regulator supply to the remaining CPU cores to address
this.
Fixes: 6eeb4180d4 ("ARM: dts: sunxi: h3-h5: Add Bananapi M2+ v1.2 device trees")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200717160053.31191-3-wens@kernel.org
The device tree currently only assigns the a supply for the first CPU
core, when in reality the regulator supply is shared by all four cores.
This might cause an issue if the implementation does not realize the
sharing of the supply.
Assign the same regulator supply to the remaining CPU cores to address
this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200717160053.31191-2-wens@kernel.org
Since commit bcf3440c6d ("net: phy: micrel: add phy-mode support for the
KSZ9031 PHY"), networking is broken on sama5d3 xplained.
The device tree has phy-mode = "rgmii" and this worked before, because
KSZ9031 PHY started with default RGMII internal delays configuration (TX
off, RX on 1.2 ns) and MAC provided TX delay. After above commit, the
KSZ9031 PHY starts handling phy mode properly and disables RX delay, as
result networking is become broken.
Fix it by switching to phy-mode = "rgmii-rxid" to reflect previous
behavior.
Fixes: bcf3440c6d ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200717233644.841080-1-alexandre.belloni@bootlin.com
Commit 1019fe2c72 ("ARM: dts: exynos: Adjust bus related OPPs to the
values correct for Exynos5422 Odroids") changed the parameters of the
OPPs for the FSYS bus. Besides the frequency adjustments, it also removed
the 'shared-opp' property from the OPP table used for FSYS_APB and FSYS
busses.
This revealed that in fact the FSYS bus frequency scaling never worked.
When one OPP table is marked as 'opp-shared', only the first bus which
selects the OPP sets the rate of its clock. Then OPP core assumes that
the other busses have been changed to that OPP and no change to their
clock rates are needed. Thus when FSYS_APB bus, which was registered
first, set the rate for its clock, the OPP core did not change the FSYS
bus clock later.
The mentioned commit removed that behavior, what introduced a regression
on some Odroid XU3 boards. Frequency scaling of the FSYS bus causes
instability of the USB host operation, what can be observed as network
hangs. To restore old behavior, simply disable frequency scaling for the
FSYS bus.
Reported-by: Willy Wolff <willy.mh.wolff.ml@gmail.com>
Fixes: 1019fe2c72 ("ARM: dts: exynos: Adjust bus related OPPs to the values correct for Exynos5422 Odroids")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
GPIOP7 is used in the Rainier design to manage the state of a
microcontroller elsewhere in the system but its ball, Y23, is the
driver of the heartbeat LED on the ast2600-evb and the SoC defaults Y23
at power-on to the pulse-train behaviour used to drive the LED. This
causes much confusion for the micro in the Rainier system, so hog the
line as early as possible.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The hub FSI master can access the cfams on two other processors. Reflect
this by adding a second cfam to the first hub description.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Tested-by: Andrew Geissler <geissonator@yahoo.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Rainier uses GPIO B6 as the checkstop GPIO. Define the line-name
so that this GPIO can be found by name.
Signed-off-by: Ben Tyner <ben.tyner@ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The attention handler will monitor the checkstop gpio via the character
device interface so it needs to not be defined.
Signed-off-by: Ben Tyner <ben.tyner@ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add a reserved memory node for the VGA memory. Add the XDMA engine node,
enable it, and point it's memory region to the VGA memory.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add a reserved memory node for the VGA memory. Add the XDMA engine node,
enable it, and point it's memory region to the VGA memory.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add the PCI-E root complex reset, correct the pcie-device property, and
add the Aspeed SCU interrupt controller include.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Correct the pcie-device property, and add the Aspeed SCU interrupt
controller include.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The current pin muxing scheme muxes GPIO_1 pad for USB_OTG_ID
because of which when card is inserted, usb otg is enumerated
and the card is never detected.
[ 64.492645] cfg80211: failed to load regulatory.db
[ 64.492657] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware
[ 76.343711] ci_hdrc ci_hdrc.0: EHCI Host Controller
[ 76.349742] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 2
[ 76.388862] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00
[ 76.396650] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.08
[ 76.405412] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 76.412763] usb usb2: Product: EHCI Host Controller
[ 76.417666] usb usb2: Manufacturer: Linux 5.8.0-rc1-next-20200618 ehci_hcd
[ 76.424623] usb usb2: SerialNumber: ci_hdrc.0
[ 76.431755] hub 2-0:1.0: USB hub found
[ 76.435862] hub 2-0:1.0: 1 port detected
The TRM mentions GPIO_1 pad should be muxed/assigned for card detect
and ENET_RX_ER pad for USB_OTG_ID for proper operation.
This patch fixes pin muxing as per TRM and is tested on a
i.Core 1.5 MX6 DL SOM.
[ 22.449165] mmc0: host does not support reading read-only switch, assuming write-enable
[ 22.459992] mmc0: new high speed SDHC card at address 0001
[ 22.469725] mmcblk0: mmc0:0001 EB1QT 29.8 GiB
[ 22.478856] mmcblk0: p1 p2
Fixes: 6df11287f7 ("ARM: dts: imx6q: Add Engicam i.CoreM6 Quad/Dual initial support")
Cc: stable@vger.kernel.org
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
esdhc0 is connected to an eMMC, so it is safe to pass the "no-sdio"/"no-sd"
properties.
esdhc1 is wired to a standard SD socket, so pass the "no-sdio" property.
Signed-off-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Commit 0672d22a19 ("ARM: dts: imx: Fix the AR803X phy-mode") fixed the
phy-mode for fec1, but missed to fix it for the fec2 node.
Fix fec2 to also use "rgmii-id" as the phy-mode.
Cc: <stable@vger.kernel.org>
Fixes: 0672d22a19 ("ARM: dts: imx: Fix the AR803X phy-mode")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Commit 0672d22a19 ("ARM: dts: imx: Fix the AR803X phy-mode") fixed the
phy-mode for fec1, but missed to fix it for the fec2 node.
Fix fec2 to also use "rgmii-id" as the phy-mode.
Cc: <stable@vger.kernel.org>
Fixes: 0672d22a19 ("ARM: dts: imx: Fix the AR803X phy-mode")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the AR8035 datasheet:
"When using crystal, the clock is generated internally after power is
stable. For a reliable power on reset, suggest to keep asserting the reset
low long enough (10ms) to ensure the clock is stable and clock-to-reset 1ms
requirement is satisfied."
Pass the 'reset-assert-us' property to describe such requirement.
While at it, use the 'reset-gpios' property inside the the mdio
node instead of the deprecated usage of 'phy-reset-gpios'.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx6q-tbs2910 has an Atheros AR8035 Ethernet PHY at address 4.
The AR8035 provides a 125MHz clock to the ENET_REF_CLK i.MX6 pin.
Improve the Ethernet representation by adding an mdio node with such
information.
This fixes an Ethernet regression in U-Boot as U-Boot AR803X driver now
expects the 'qca,clk-out-frequency' property to be passed via
device tree.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Soeren Moch <smoch@web.de>
Tested-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the AR8031 datasheet:
"When using crystal, clock is generated internally after the power is
stable. In order to get reliable power-on-reset, it is recommended to
keep asserting the reset low signal long enough (10 ms) to ensure the
clock is stable and clock-to-reset (1 ms) requirement is satisfied."
Pass the 'reset-assert-us' property to describe such requirement.
While at it, use the 'reset-gpios' property inside the the mdio
node instead of the deprecated usage of 'phy-reset-gpios'.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx6qdl-sabresd has an Atheros AR8031 Ethernet PHY at address 1.
The AR8031 provides a 125MHz clock to the ENET_REF_CLK i.MX6 pin.
Improve the Ethernet representation by adding an mdio node with such
information.
An advantage of adding the mdio node is that the AR8031 initialization
code in the mx6sabresd board file in U-Boot can totally be removed.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add Gateworks System Controller support to Gateworks Ventana boards:
- add dt bindings for GSC mfd driver and hwmon driver for ADC's and
fan controllers.
- add dt bindings for gpio-keys driver for push-button and interrupt events
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The marvell PHY reg-init registers for the D-Link DNS-327L are wrong.
Currently the first field is used to set the page 2, but this is
pointless. The usage is not correct, and we are setting the wrong
registers.
Fix it.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Connect the voltage regulator of vbus to the otg connector.
Depending on the current mode this is enabled (in "host" mode")
or disabled (in "peripheral" mode). The regulator must be updated
if the controller is configured in "otg" mode and the status changes
between "host" and "peripheral".
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Link: https://lore.kernel.org/r/20200707101214.2301768-1-michael@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Rock Pi N8 is a Rockchip RK3288 based SBC, which has
- VMARC RK3288 SOM (as per SMARC standard) from Vamrs.
- Compatible carrier board from Radxa.
VAMRC RK3288 SOM need to mount on top of radxa dalang
carrier board for making Rock Pi N8 SBC.
So, add initial support for Rock Pi N8 by including rk3288,
rk3288 vamrc-som and raxda dalang carrier board dtsi files.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20200715083418.112003-8-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
VMARC RK3288 SOM is a standard SMARC SOM design with
Rockchip RK3288 SoC, which is designed by Vamrs.
Specification:
- Rockchip RK3288
- PMIC: RK808
- eMMC: 16GB/32GB/64GB
- SD slot
- 2xUSB-2.0, 1xUSB3.0
- USB-C for power supply
- Ethernet
- HDMI, MIPI-DSI/CSI, eDP
Add initial support for VMARC RK3288 SOM, this would use
with associated carrier board.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20200715083418.112003-7-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Some of gmac, sdmmc node properties are common across rk3288 and
rk3399pro SOM's so move them into Carrier dtsi.
Chosen node is specific to rk3399pro configure SBC, so move it into
RockPI N10 dts.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20200715083418.112003-5-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Supply regulators are common across different variants of vmarc SOM's
since the Type C power controller IC is part of the carrier board.
So, move the supply regulators into carrier board dtsi.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20200715083418.112003-4-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
I2C nodes and associated slave devices defined in Carrier board
are specific to rk3399pro vmrac SOM.
So, move them into SOM dtsi.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20200715083418.112003-2-jagan@amarulasolutions.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This time there are a number of actual code fixes, plus
a small set of device tree issues getting addressed:
- Renesas:
- one defconfig cleanup to allow a later Kconfig change
- Intel socfpga:
- enable QSPI devices on some machines
- fix DTC validation warnings
- TI OMAP:
- Two DEBUG_ATOMIC_SLEEP fixes for ti-sysc interconnect target module
driver
- A regression fix for ti-sysc no-idle handling that caused issues
compared to earlier platform data based booting
- A fix for memory leak for omap_hwmod_allocate_module
- Fix d_can driver probe for am437x
- NXP i.MX
- A couple of fixes on i.MX platform device registration code to stop
the use of invalid IRQ 0.
- Fix a regression seen on ls1021a platform, caused by commit
52102a3ba6 ("soc: imx: move cpu code to drivers/soc/imx").
- Fix a misconfiguration of audio SSI on imx6qdl-gw551x board.
- Amlogic Meson
- misc DT fixes
- SoC ID fixes to detect all chips correctly
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=Xlng
-----END PGP SIGNATURE-----
Merge tag 'arm-fixes-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc into master
Pull ARM SoC fixes from Arnd Bergmann:
"This time there are a number of actual code fixes, plus a small set of
device tree issues getting addressed:
Renesas:
- one defconfig cleanup to allow a later Kconfig change
Intel socfpga:
- enable QSPI devices on some machines
- fix DTC validation warnings
TI OMAP:
- Two DEBUG_ATOMIC_SLEEP fixes for ti-sysc interconnect target
module driver
- A regression fix for ti-sysc no-idle handling that caused issues
compared to earlier platform data based booting
- A fix for memory leak for omap_hwmod_allocate_module
- Fix d_can driver probe for am437x
NXP i.MX:
- A couple of fixes on i.MX platform device registration code to
stop the use of invalid IRQ 0.
- Fix a regression seen on ls1021a platform, caused by commit
52102a3ba6 ("soc: imx: move cpu code to drivers/soc/imx").
- Fix a misconfiguration of audio SSI on imx6qdl-gw551x board.
Amlogic Meson:
- misc DT fixes
- SoC ID fixes to detect all chips correctly"
* tag 'arm-fixes-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
arm64: dts: spcfpga: Align GIC, NAND and UART nodenames with dtschema
ARM: dts: socfpga: Align L2 cache-controller nodename with dtschema
arm64: dts: stratix10: increase QSPI reg address in nand dts file
arm64: dts: stratix10: add status to qspi dts node
arm64: dts: agilex: add status to qspi dts node
ARM: dts: Fix dcan driver probe failed on am437x platform
ARM: OMAP2+: Fix possible memory leak in omap_hwmod_allocate_module
arm64: defconfig: Enable CONFIG_PCIE_RCAR_HOST
soc: imx: check ls1021a
ARM: imx: Remove imx_add_imx_dma() unused irq_err argument
ARM: imx: Provide correct number of resources when registering gpio devices
ARM: dts: imx6qdl-gw551x: fix audio SSI
bus: ti-sysc: Do not disable on suspend for no-idle
bus: ti-sysc: Fix sleeping function called from invalid context for RTC quirk
bus: ti-sysc: Fix wakeirq sleeping function called from invalid context
ARM: dts: meson: Align L2 cache-controller nodename with dtschema
arm64: dts: meson-gxl-s805x: reduce initial Mali450 core frequency
arm64: dts: meson: add missing gxl rng clock
soc: amlogic: meson-gx-socinfo: Fix S905X3 and S905D3 ID's
This adds device trees for the ASUS Google Nexus 7 and Acer Iconia Tab
A500. In addition there are a slew of fixes to existing device trees in
preparation for validating the DTBs against json-schema.
-----BEGIN PGP SIGNATURE-----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=oFYm
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.9-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
ARM: tegra: Device tree changes for v5.9-rc1
This adds device trees for the ASUS Google Nexus 7 and Acer Iconia Tab
A500. In addition there are a slew of fixes to existing device trees in
preparation for validating the DTBs against json-schema.
* tag 'tegra-for-5.9-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (38 commits)
ARM: tegra: Add device-tree for ASUS Google Nexus 7
ARM: tegra: Add device-tree for Acer Iconia Tab A500
ARM: tegra: Add HDMI supplies on Nyan boards
ARM: tegra: Add missing DSI controller on Tegra30
ARM: tegra: Add i2c-bus subnode for DPAUX controllers
ARM: tegra: The Tegra30 SDHCI is not backwards-compatible
ARM: tegra: The Tegra30 DC is not backwards-compatible
ARM: tegra: Remove spurious comma from node name
ARM: tegra: Add parent clock to DSI output
ARM: tegra: Use standard names for SRAM nodes
ARM: tegra: seaboard: Use standard battery bindings
ARM: tegra: Use standard names for LED nodes
ARM: tegra: Use numeric unit-addresses
ARM: tegra: medcom-wide: Remove extra panel power supply
ARM: tegra: Use proper unit-addresses for OPPs
ARM: tegra: Add missing clock-names for SDHCI controllers
ARM: tegra: Fix order of XUSB controller clocks
ARM: tegra: Add #reset-cells to Tegra124 memory controller
ARM: tegra: Add missing panel power supplies
ARM: tegra: Add micro-USB A/B port on Jetson TK1
...
Link: https://lore.kernel.org/r/20200717161300.1661002-5-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The device node for the FIFO-buffered Serial Interface sound node lacks
the "clocks" property, as the DTS file didn't describe any clocks yet at
its introduction.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200519075525.24742-1-geert+renesas@glider.be
Fix dtschema validator warnings like:
l2-cache: $nodename:0: 'l2-cache' does not match '^(cache-controller|cpu)(@[0-9a-f,]+)*$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
A series of changes to configure IPU and DSP remoteproc for omap4 & 5.
And a change to configure the default mux for am335x-pocketbeagle, and
a change to use https for external links.
-----BEGIN PGP SIGNATURE-----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=IlyP
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.9/dt-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
More dts changes for omaps for v5.9
A series of changes to configure IPU and DSP remoteproc for omap4 & 5.
And a change to configure the default mux for am335x-pocketbeagle, and
a change to use https for external links.
* tag 'omap-for-v5.9/dt-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
Replace HTTP links with HTTPS ones: OMAP DEVICE TREE SUPPORT
ARM: dts: omap5-uevm: Add watchdog timers for IPU and DSP
ARM: dts: omap4-panda-common: Add watchdog timers for IPU and DSP
ARM: dts: omap5-uevm: Add system timers to DSP and IPU
ARM: dts: omap5-uevm: Add CMA pools and enable IPU & DSP
ARM: dts: omap5: Add aliases for rproc nodes
ARM: dts: omap5: Add DSP and IPU nodes
ARM: dts: omap4-panda-common:: Add system timers to DSP and IPU
ARM: dts: omap4-panda-common: Add CMA pools and enable IPU & DSP
ARM: dts: omap4: Add aliases for rproc nodes
ARM: dts: omap4: Add IPU DT node
ARM: dts: omap4: Update the DSP node
ARM: dts: omap5: Add timer_sys_ck clocks for timers
ARM: dts: omap4: Add timer_sys_ck clocks for timers
ARM: dts: am335x-pocketbeagle: set default mux for gpio pins
Link: https://lore.kernel.org/r/pull-1594838111-649880@atomide.com-3
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A series of changes to drop remaining USB platform data for omap4/5,
and am4, and dra7.
And a patch to drop AES platform data for omap3.
-----BEGIN PGP SIGNATURE-----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=4iOb
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.9/ti-sysc-drop-pdata-take2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
Drop more legacy platform data for omaps for v5.9
A series of changes to drop remaining USB platform data for omap4/5,
and am4, and dra7.
And a patch to drop AES platform data for omap3.
* tag 'omap-for-v5.9/ti-sysc-drop-pdata-take2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Drop legacy platform data for omap5 usb host
ARM: OMAP2+: Drop legacy platform data for omap4 usb
ARM: OMAP2+: Drop legacy platform data for dra7 dwc3
ARM: OMAP2+: Drop legacy platform data for omap5 dwc3
ARM: OMAP2+: Drop legacy platform data for am4 dwc3
bus: ti-sysc: Add missing quirk flags for usb_host_hs
ARM: dts: omap3: Migrate AES from hwmods to sysc-omap2
Link: https://lore.kernel.org/r/pull-1594838111-649880@atomide.com-2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Few fixes for issues noticed during testing:
- Two DEBUG_ATOMIC_SLEEP fixes for ti-sysc interconnect target module
driver
- A regression fix for ti-sysc no-idle handling that caused issues
compared to earlier platform data based booting
- A fix for memory leak for omap_hwmod_allocate_module
- Fix d_can driver probe for am437x
-----BEGIN PGP SIGNATURE-----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=ekbH
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.8/fixes-rc5-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for v5.8-rc cycle
Few fixes for issues noticed during testing:
- Two DEBUG_ATOMIC_SLEEP fixes for ti-sysc interconnect target module
driver
- A regression fix for ti-sysc no-idle handling that caused issues
compared to earlier platform data based booting
- A fix for memory leak for omap_hwmod_allocate_module
- Fix d_can driver probe for am437x
* tag 'omap-for-v5.8/fixes-rc5-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix dcan driver probe failed on am437x platform
ARM: OMAP2+: Fix possible memory leak in omap_hwmod_allocate_module
bus: ti-sysc: Do not disable on suspend for no-idle
bus: ti-sysc: Fix sleeping function called from invalid context for RTC quirk
bus: ti-sysc: Fix wakeirq sleeping function called from invalid context
Link: https://lore.kernel.org/r/pull-1594840100-132735@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- A couple of fixes on i.MX platform device registration code to stop
the use of invalid IRQ 0.
- Fix a regression seen on ls1021a platform, caused by commit
52102a3ba6 ("soc: imx: move cpu code to drivers/soc/imx").
- Fix a misconfiguration of audio SSI on imx6qdl-gw551x board.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl8Nxv4UHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM4fIAf/SKUzFbQ/INaU98yW8zONnZVzD/jI
3oTnBP87YJRNiyrLF1lWLs55vfnhum7yXJZXdMbwP55fdJKVaV4StePGz9Sh4Gba
4COHOF3XvF73b4kpcCQEr1U+Y0KHEfMbkwONmerk9ZkRThY2uqcRsdj4br+XA9eU
19ppWdOYZHMjegPu0KuxJlevZJDO6s9I4MCKFWmGgWhanLeGXXd2xtJEgqTWtTnS
EFjOFdBQF+5yd0VY/j6WHBDHWa/fXhDFoAO8Wc5LMCP3VybZdciIi4mN8y0UZoNG
Q5UnBvpYMCqrBwVlyqgeDtJUvYd+33dHqsRbU3KN8yBpRnyHupR9UvcFLA==
=+Gmy
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.8, round 2:
- A couple of fixes on i.MX platform device registration code to stop
the use of invalid IRQ 0.
- Fix a regression seen on ls1021a platform, caused by commit
52102a3ba6 ("soc: imx: move cpu code to drivers/soc/imx").
- Fix a misconfiguration of audio SSI on imx6qdl-gw551x board.
* tag 'imx-fixes-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx: check ls1021a
ARM: imx: Remove imx_add_imx_dma() unused irq_err argument
ARM: imx: Provide correct number of resources when registering gpio devices
ARM: dts: imx6qdl-gw551x: fix audio SSI
Link: https://lore.kernel.org/r/20200714145649.GP15718@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There are few hardware variants of NVIDIA Tegra30-based Nexus 7 device:
1. WiFi-only (named Grouper)
2. GSM (named Tilapia)
3. Using Maxim PMIC (E1565 board ID)
4. Using Ti PMIC (PM269 board ID)
This patch adds device-trees for known and tested variants.
Link: https://wiki.postmarketos.org/wiki/Google_Nexus_7_2012_(asus-grouper)
Tested-by: Pedro Ângelo <pangelo@void.io>
Tested-by: Matt Merhar <mattmerhar@protonmail.com>
Tested-by: Zack Pearsall <zpearsall@yahoo.com>
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Fix dtschema validator warnings like:
l2-cache@fffff000: $nodename:0:
'l2-cache@fffff000' does not match '^(cache-controller|cpu)(@[0-9a-f,]+)*$'
Fixes: 475dc86d08 ("arm: dts: socfpga: Add a base DTSI for Altera's Arria10 SOC")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
The SOR controller needs the AVDD I/O and VDD HDMI PLL supplies in order
to operate correctly. Make sure to specify them for Nyan boards.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra30 has a DSI controller, although it is never used on any of the
devices supported by the upstream Linux kernel.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DPAUX controller device tree bindings require the bus to have an
i2c-bus subnode to distinguish between I2C clients and pinmux groups.
Signed-off-by: Thierry Reding <treding@nvidia.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Got following d_can probe errors with kernel 5.8-rc1 on am437x
[ 10.730822] CAN device driver interface
Starting Wait for Network to be Configured...
[ OK ] Reached target Network.
[ 10.787363] c_can_platform 481cc000.can: probe failed
[ 10.792484] c_can_platform: probe of 481cc000.can failed with error -2
[ 10.799457] c_can_platform 481d0000.can: probe failed
[ 10.804617] c_can_platform: probe of 481d0000.can failed with error -2
actually, Tony has fixed this issue on am335x with the patch [3]
Since am437x has the same clock structure with am335x
[1][2], so reuse the code from Tony Lindgren's patch [3] to fix it.
[1]: https://www.ti.com/lit/pdf/spruh73 Chapter-23, Figure 23-1. DCAN
Integration
[2]: https://www.ti.com/lit/pdf/spruhl7 Chapter-25, Figure 25-1. DCAN
Integration
[3]: commit 516f1117d0 ("ARM: dts: Configure osc clock for d_can on
am335x")
Fixes: 1a5cd7c23c ("bus: ti-sysc: Enable all clocks directly during init to read revision")
Signed-off-by: dillon min <dillon.minfei@gmail.com>
[tony@atomide.com: aligned commit message a bit for readability]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull input fixes from Dmitry Torokhov:
"A few quirks for the Elan touchpad driver, another Thinkpad is being
switched over from PS/2 to native RMI4 interface, and we gave a brand
new SW_MACHINE_COVER switch definition"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elan_i2c - add more hardware ID for Lenovo laptops
Input: i8042 - add Lenovo XiaoXin Air 12 to i8042 nomux list
Revert "Input: elants_i2c - report resolution information for touch major"
Input: elan_i2c - only increment wakeup count on touch
Input: synaptics - enable InterTouch for ThinkPad X1E 1st gen
ARM: dts: n900: remove mmc1 card detect gpio
Input: add `SW_MACHINE_COVER`
Odroid-C1 has an eMMC connector where users can optionally install an
eMMC module. The eMMC modules run off a 1.8V VQMMC supply which means
that HS-200 mode can be used (this is the highest mode that the SDHC
controller supports). Enable the SDHC controller so eMMC modules can be
accessed.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200620163654.37207-4-martin.blumenstingl@googlemail.com
EC-100 has built-in eMMC flash which is hard-wired to 3.3V VCC (which
means it's limited to high-speed MMC modes). Enable the SDHC controller
to access the contents of the eMMC flash.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200620163654.37207-3-martin.blumenstingl@googlemail.com
Meson6, Meson8, Meson8b and Meson8m2 are using a similar SDHC controller
IP which typically connects to an eMMC chip (because unlike the SDIO
controller the SDHC controller has an 8-bit bus interface).
On Meson8, Meson8b and Meson8m2 the clock inputs are all the same.
However, Meson8m2 seems to have an improved version of the SHDC
controller IP which doesn't require the driver to wait manually for a
flush of a DMA transfer. Thus every SoC has it's own compatible string
so if more difference are discovered they can be implemented.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200620163654.37207-2-martin.blumenstingl@googlemail.com
The Meson8b SoCs have a power domain controller which can turn on/off
various register areas (such as: Ethernet, VPU, etc.).
Add the main "pwrc" controller and configure the Ethernet power domain.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200620161010.23171-4-martin.blumenstingl@googlemail.com
The Meson8m2 SoCs has introduced additional reset lines for the VPU
compared to Meson8. Also it uses a slightly different VPU clock
frequency compared to Meson8 since it can now achieve 364MHz thanks to
the addition of the GP_PLL.
Add the reset lines, VPU clock configuration and update the compatible
string so the implementation differences can be managed.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200620161010.23171-3-martin.blumenstingl@googlemail.com
The Meson8 SoCs have a power domain controller which can turn on/off
various register areas (such as: Ethernet, VPU, etc.).
Add the main "pwrc" controller and configure the Ethernet power domain.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200620161010.23171-2-martin.blumenstingl@googlemail.com
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The watchdog timers have been added for the IPU and DSP remoteproc
devices for the OMAP5 uEVM board. The following timers (same as the
timers on OMAP4 Panda boards) are used as the watchdog timers,
DSP : GPT6
IPU : GPT9 & GPT11 (one for each Cortex-M4 core)
The MPU-side drivers will use this data to initialize the watchdog
timers, and listen for any watchdog triggers. The BIOS-side code
needs to configure and refresh these timers properly to not throw
a watchdog error.
These timers can be changed or removed as per the system integration
needs, alongside appropriate equivalent changes on the firmware side.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The watchdog timers have been added for the IPU and DSP remoteproc
devices on all the OMAP4-based Panda boards. The following timers
are used as the watchdog timers,
DSP : GPT6
IPU : GPT9 & GPT11 (one for each Cortex-M3 core)
The MPU-side drivers will use this data to initialize the watchdog
timers, and listen for any watchdog triggers. The BIOS-side code
needs to configure and refresh these timers properly to not throw
a watchdog error.
These timers can be changed or removed as per the system integration
needs, alongside appropriate equivalent changes on the firmware side.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The BIOS System Tick timers have been added for the IPU and DSP
remoteproc devices for the OMAP5 uEVM boards. The following timers
(same as the timers on OMAP4 Panda boards) are chosen:
IPU : GPT3 (SMP-mode)
DSP : GPT5
IPU has two Cortex-M4 processors, and is currently expected to be
running in SMP-mode, so only a single timer suffices to provide
the BIOS tick timer. An additional timer should be added for the
second processor in IPU if it were to be run in non-SMP mode. The
timer value also needs to be unique from the ones used by other
processors so that they can be run simultaneously.
The timers are optional, but are mandatory to support device
management features such as power management and watchdog support.
The above are added to successfully boot and execute firmware images
configured with the respective timers, images that use internal
processor subsystem timers are not affected. The timers can be
changed or removed as per the system integration needs, alongside
equivalent changes on the firmware side.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for the IPU and DSP
remoteproc devices on the OMAP5 uEVM board. These nodes are assigned
to the respective rproc device nodes, and both the IPU and DSP remote
processors are enabled for this board.
The current CMA pools and sizes are defined statically for each device.
The starting addresses are fixed to meet current dependencies on the
remote processor firmwares, and will go away when the remote-side
code has been improved to gather this information runtime during
its initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add aliases for the DSP and IPU remoteproc processor
nodes common to all OMAP5 boards. The aliases uses
the stem "rproc", and are identical to the values
chosen on OMAP4 boards.
The aliases can be overridden, if needed, in the
respective board files.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP5, like OMAP4, also has two remote processor subsystems,
DSP and IPU. The IPU subsystem though has dual Cortex-M4
processors instead of the dual Cortex-M3 processors in OMAP4,
but otherwise has almost the same set of features. Add the
DT nodes for these two processor sub-systems for all OMAP5
SoCs.
The nodes have the 'iommus', 'clocks', 'resets', 'firmware' and
'mboxes' properties added, and are disabled for now. The IPU node
has its L2 RAM memory specified through the 'reg' and 'reg-names'
properties. The DSP node doesn't have these since it doesn't have
any L2 RAM memories, but has an additional 'ti,bootreg' property
instead as it has a specific boot register that needs to be
programmed for booting.
These nodes should be enabled as per the individual product
configuration in the corresponding board dts files.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The BIOS System Tick timers have been added for the IPU and DSP
remoteproc devices on all the OMAP4-based Panda boards. The
following DMTimers are chosen:
IPU : GPT3 (SMP-mode)
DSP : GPT5
IPU has two Cortex-M3 processors, and is currently expected to be
running in SMP-mode, so only a single timer suffices to provide
the BIOS tick timer. An additional timer should be added for the
second processor in IPU if it were to be run in non-SMP mode. The
timer value also needs to be unique from the ones used by other
processors so that they can be run simultaneously.
The timers are optional, but are mandatory to support device
management features such as power management and watchdog support.
The above are added to successfully boot and execute firmware images
configured with the respective timers, images that use internal
processor subsystem timers are not affected. The timers can be
changed or removed as per the system integration needs, alongside
equivalent changes on the firmware side.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for the IPU and DSP
remoteproc devices on all the OMAP4-based Panda boards. These nodes
are assigned to the respective rproc device nodes, and both the
IPU and DSP remote processors are enabled for all these boards.
The current CMA pools and sizes are defined statically for each device.
The starting addresses are fixed to meet current dependencies on the
remote processor firmwares, and will go away when the remote-side
code has been improved to gather this information runtime during
its initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
