- Make sure PCIe is reset before init to work around QSDK U-Boot issue
(Ansuel Smith)
- Set iproc affinity mask on MSI interrupts (Mark Tomlinson)
* remotes/lorenzo/pci/qcom:
PCI: qcom: Make sure PCIe is reset before init for rev 2.1.0
- Return -EPROBE_DEFER in case the gpio isn't ready (Bean Huo)
* remotes/lorenzo/pci/kirin:
PCI: kirin: Return -EPROBE_DEFER in case the gpio isn't ready
- Use "fallthrough" pseudo-keyword (Gustavo A. R. Silva)
- Drop redundant error messages after devm_clk_get() (Anson Huang)
* remotes/lorenzo/pci/imx6:
PCI: imx6: Do not output error message when devm_clk_get() failed with -EPROBE_DEFER
PCI: imx6: Use fallthrough pseudo-keyword
NXP Layerscape (ls1028a, ls2088a), dra7xxx and imx6 platforms are either
programmed or statically configured to forward the error triggered by a
link-down state (eg no connected endpoint device) on the system bus for
PCI configuration transactions; these errors are reported as an SError
at system level, which is fatal.
Enumerating a PCI tree when the PCIe link is down is not sensible
either, so even if the link-up check is racy (link can go down after
map_bus() is called) add a link-up check in map_bus() to prevent issuing
configuration transactions when the link is down.
SError report:
SError Interrupt on CPU2, code 0xbf000002 -- SError
CPU: 2 PID: 1 Comm: swapper/0 Not tainted 5.9.0-rc5-next-20200914-00001-gf965d3ec86fa #67
Hardware name: LS1046A RDB Board (DT)
pstate: 20000085 (nzCv daIf -PAN -UAO BTYPE=--)
pc : pci_generic_config_read+0x3c/0xe0
lr : pci_generic_config_read+0x24/0xe0
sp : ffff80001003b7b0
x29: ffff80001003b7b0 x28: ffff80001003ba74
x27: ffff000971d96800 x26: ffff00096e77e0a8
x25: ffff80001003b874 x24: ffff80001003b924
x23: 0000000000000004 x22: 0000000000000000
x21: 0000000000000000 x20: ffff80001003b874
x19: 0000000000000004 x18: ffffffffffffffff
x17: 00000000000000c0 x16: fffffe0025981840
x15: ffffb94c75b69948 x14: 62203a383634203a
x13: 666e6f635f726568 x12: 202c31203d207265
x11: 626d756e3e2d7375 x10: 656877202c307830
x9 : 203d206e66766564 x8 : 0000000000000908
x7 : 0000000000000908 x6 : ffff800010900000
x5 : ffff00096e77e080 x4 : 0000000000000000
x3 : 0000000000000003 x2 : 84fa3440ff7e7000
x1 : 0000000000000000 x0 : ffff800010034000
Kernel panic - not syncing: Asynchronous SError Interrupt
CPU: 2 PID: 1 Comm: swapper/0 Not tainted 5.9.0-rc5-next-20200914-00001-gf965d3ec86fa #67
Hardware name: LS1046A RDB Board (DT)
Call trace:
dump_backtrace+0x0/0x1c0
show_stack+0x18/0x28
dump_stack+0xd8/0x134
panic+0x180/0x398
add_taint+0x0/0xb0
arm64_serror_panic+0x78/0x88
do_serror+0x68/0x180
el1_error+0x84/0x100
pci_generic_config_read+0x3c/0xe0
dw_pcie_rd_other_conf+0x78/0x110
pci_bus_read_config_dword+0x88/0xe8
pci_bus_generic_read_dev_vendor_id+0x30/0x1b0
pci_bus_read_dev_vendor_id+0x4c/0x78
pci_scan_single_device+0x80/0x100
Link: https://lore.kernel.org/r/20200916054130.8685-1-Zhiqiang.Hou@nxp.com
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[lorenzo.pieralisi@arm.com: rewrote the commit log, remove Fixes tag]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Currently, dw_pcie_msi_init() allocates and maps page for msi, then
program the PCIE_MSI_ADDR_LO and PCIE_MSI_ADDR_HI. The Root Complex
may lose power during suspend-to-RAM, so when we resume, we want to
redo the latter but not the former. If designware based driver (for
example, pcie-tegra194.c) calls dw_pcie_msi_init() in resume path, the
msi page will be leaked.
As pointed out by Rob and Ard, there's no need to allocate a page for
the MSI address, we could use an address in the driver data.
To avoid map the MSI msg again during resume, we move the map MSI msg
from dw_pcie_msi_init() to dw_pcie_host_init().
Suggested-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201009155505.5a580ef5@xhacker.debian
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
If MSI is disabled, there's no need to program PCIE_MSI_INTR0_MASK
and PCIE_MSI_INTR0_ENABLE registers.
Link: https://lore.kernel.org/r/20201009155436.27e67238@xhacker.debian
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
After applying "PCI: dwc: Add common iATU register support",
there is no need to set own iATU in the Keystone driver itself.
Suggested-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1601444167-11316-5-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
This gets iATU register area from reg property that has reg-names "atu".
In Synopsys DWC version 4.80 or later, since iATU register area is
separated from core register area, this area is necessary to get from
DT independently.
Suggested-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1601444167-11316-4-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Enable pci-meson to build as a module whenever ARCH_MESON is enabled.
Link: https://lore.kernel.org/r/20200918181251.32423-1-khilman@baylibre.com
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Cc: Yue Wang <yue.wang@amlogic.com>
PCI host bridge driver can be probed before the gpiochip it requires,
so, of_get_named_gpio() can return -EPROBE_DEFER. Current code lets the
kirin_pcie_probe() directly return -ENODEV, which results in the PCI
host controller driver probe failure; with this error code the PCI host
controller driver will not be probed again when the gpiochip driver is
loaded.
Fix the above issue by letting kirin_pcie_probe() return -EPROBE_DEFER in
such a case.
Link: https://lore.kernel.org/r/20200918123800.19983-1-huobean@gmail.com
Signed-off-by: Bean Huo <beanhuo@micron.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add PCIe EP mode support for ls1088a and ls2088a, there are some
difference between LS1 and LS2 platform, so refactor the code of
the EP driver.
Link: https://lore.kernel.org/r/20200918080024.13639-10-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
dw_pcie_ep_raise_msix_irq was never called in the exisitng driver
before, because the ls1046a platform don't support the MSIX feature
and msix_capable was always set to false.
Now that add the ls1088a platform with MSIX support, use the doorbell
method to support the MSIX feature.
Link: https://lore.kernel.org/r/20200918080024.13639-9-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
The different PCIe controller in one board may be have different
capability of MSI or MSIX, so change the way of getting the MSI
capability, make it more flexible.
Link: https://lore.kernel.org/r/20200918080024.13639-8-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Fix some format issue of the code in EP driver.
Link: https://lore.kernel.org/r/20200918080024.13639-7-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Each PF of EP device should have its own MSI or MSIX capabitily
struct, so create a dw_pcie_ep_func struct and move the msi_cap
and msix_cap to this struct from dw_pcie_ep, and manage the PFs
via a list.
Link: https://lore.kernel.org/r/20200918080024.13639-5-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Move the function of getting MSI capability to the front of init
function, because the init function of the EP platform driver will use
the return value by the function of getting MSI capability.
Link: https://lore.kernel.org/r/20200918080024.13639-4-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Add the doorbell mode of MSI-X in DWC EP driver.
Link: https://lore.kernel.org/r/20200918080024.13639-3-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Add multiple PFs support for DWC, due to different PF have different
config space, we use func_conf_select callback function to access
the different PF's config space, the different chip company need to
implement this callback function when use the DWC IP core and intend
to support multiple PFs feature.
Link: https://lore.kernel.org/r/20200918080024.13639-2-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Convert the remaining cases of register accesses using dbi_base rather
than dw_pcie_(read|write)[bwl]_dbi accessors.
Link: https://lore.kernel.org/r/20200821035420.380495-41-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
The Designware controller has common registers to set number of fast
training sequence ordered sets. The Artpec6, Intel, and Tegra driver
initialize these register fields. Let's move the initialization to the
common setup code and drivers just have to provide the value.
There's a slight change in that the common clock mode N_FTS field is
now initialized. Previously only the Intel driver set this. It's not
clear from the code if common clock mode is used in the Artpec6 or Tegra
driver. It depends on the DWC configuration. Given the field is not
initialized while the others are, it seems unlikely common clock mode
is used.
Link: https://lore.kernel.org/r/20200821035420.380495-40-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
'max_width' is read, but never used, so let's remove it.
Link: https://lore.kernel.org/r/20200821035420.380495-39-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Dilip Kota <eswara.kota@linux.intel.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The PCI_CAP_ID_EXP offset is only needed by intel_pcie_link_setup(), so
let's retrieve it there and avoid storing the offset.
Link: https://lore.kernel.org/r/20200821035420.380495-38-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Dilip Kota <eswara.kota@linux.intel.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
A driver doesn't need to check for DT 'device_type' property, so let's
remove the check.
Link: https://lore.kernel.org/r/20200821035420.380495-37-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Dilip Kota <eswara.kota@linux.intel.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The Intel driver is the only one to set PORT_LINK_DLL_LINK_EN. The
default value is set and it seems pretty certain that enabling link
initialization is always required. Maybe it could just be dropped from
the Intel driver, but lets move setting it into the common code to be
sure.
Link: https://lore.kernel.org/r/20200821035420.380495-36-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Dilip Kota <eswara.kota@linux.intel.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The ATU registers are only accessed in pcie-designware.c and can be private
to it.
Link: https://lore.kernel.org/r/20200821035420.380495-34-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The DBI2 appears to be write-only and there's no read accesses in the code
anyways, so let's remove all the read_dbi2 related code.
Link: https://lore.kernel.org/r/20200821035420.380495-33-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
The Tegra driver has its own defines for common Designware Port Logic
registers. Convert it to use the standard register definitions.
Link: https://lore.kernel.org/r/20200821035420.380495-32-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
While the Designware controller appears to hard code the PCI_CAP_ID_EXP
capability register at 0x70, there's no need to hard code this in the
driver as it is discoverable.
Link: https://lore.kernel.org/r/20200821035420.380495-31-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Cc: linux-omap@vger.kernel.org
The QCom driver has its own defines for common PCI config space
registers. It also hard codes the capability register offsets which are
discoverable. Convert it to use the standard register definitions.
Link: https://lore.kernel.org/r/20200821035420.380495-30-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-arm-msm@vger.kernel.org
The i.MX6 driver has its own defines for common PCI config space
registers. It also hard codes the capability register offsets which are
discoverable. Convert it to use the standard register definitions.
Link: https://lore.kernel.org/r/20200821035420.380495-29-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
The meson 'elbi' registers are just the Designware 'dbi' space and all
the registers accessed are either standard PCI config space or DWC port
logic registers. Convert the accesses to use the common defines and
register accessors.
Link: https://lore.kernel.org/r/20200821035420.380495-28-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: linux-amlogic@lists.infradead.org
The common Designware init already initializes the RC PCI_COMMAND, BAR0
and BAR1 registers.
The only difference here is the common code sets SERR. If clearing SERR
is what's desired, then the Meson driver should do that instead.
Link: https://lore.kernel.org/r/20200821035420.380495-27-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: linux-amlogic@lists.infradead.org
The meson lanes initialization is the same DWC port logic registers as
in dw_pcie_setup(). We just need to initialize 'num_lanes' to 1 to do
the same init.
dw_pcie_setup_rc() sets the PORT_LOGIC_SPEED_CHANGE bit, so setting it
can be dropped.
Link: https://lore.kernel.org/r/20200821035420.380495-26-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: linux-amlogic@lists.infradead.org
"Fast Link Mode" is a simulation environment speed up setting which should
never be set and the default is not set. However some Amlogic platforms
have it set (by firmware presumably). See commit 87dccf0932 ("PCI:
amlogic: meson: Don't use FAST_LINK_MODE to set up link") for more
information. Let's clear it in core DWC code so we can drop some vendor
specific code.
Link: https://lore.kernel.org/r/20200821035420.380495-25-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Add a 'num_lanes' field to allow drivers to provide a the number of lanes
if not in DT or using a custom DT property. A driver can provide a
non-zero value which is used if the DT doesn't have a 'num-lanes'
property.
Link: https://lore.kernel.org/r/20200821035420.380495-24-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
PCIE_LINK_WIDTH_SPEED_CONTROL is already defined in pcie-designware.h,
so remove it from the i.MX6 driver.
Link: https://lore.kernel.org/r/20200821035420.380495-23-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
The DWC core driver already parses and stores the 'num-viewport' DT
property, so there is no need for the Keystone driver to store it.
Link: https://lore.kernel.org/r/20200821035420.380495-21-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The config space is divided in half for type 0 and type 1 accesses, but
this is pointless as there's only one iATU window which is
reconfigured on each access.
The only platform doing something custom is TI Keystone (surprise!).
It does its own mapping of the config space to avoid spliting the
config space and never actually uses va_cfg1_base as it has its own
config space accessors. With the splitting removed, Keystone can use the
default mapping of config space.
Link: https://lore.kernel.org/r/20200821035420.380495-20-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
The PCI bridge resources are stored in pci_host_bridge.windows, so
there's no need to store them in a DWC specific struct. There's also no
need to parse the resources and store them a 2nd time as they are mainly
used for one time setup of iATU windows.
Link: https://lore.kernel.org/r/20200821035420.380495-19-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jonathan Chocron <jonnyc@amazon.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
The pci_host_bridge struct already has a pointer to its pci_bus, so
let's convert the one user to use the bridge struct and remove the
private 'root_bus' pointer.
Link: https://lore.kernel.org/r/20200821035420.380495-18-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Now that there are no more .scan_bus() callbacks, we can remove it and just
use pci_host_probe().
Link: https://lore.kernel.org/r/20200821035420.380495-17-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
TI keystone is the only Designware driver using .scan_bus(). This
function pointer is the only thing preventing the Designware driver from
using pci_host_probe(). Let's use the pci_ops.add_bus hook instead.
Link: https://lore.kernel.org/r/20200821035420.380495-16-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Now that all the platforms with custom config access handling define
their own pci_ops, let's split the default config accessors to use
different pci_ops for root and child buses. With this, we can use the
generic config accessors. The child bus accesses mainly require a
.map_bus() hook to reconfigure the iATU on each config space access.
Link: https://lore.kernel.org/r/20200821035420.380495-14-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Now that all the drivers needing custom config accessors have been
converted to define their own pci_ops, we can remove the DWC specific
function callbacks {rd,wr}_{own,other}_conf.
Link: https://lore.kernel.org/r/20200821035420.380495-13-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Now that DWC drivers can setup their own pci_ops for the root and child
buses, convert the HiSilicon histb driver to use the standard pci_ops
for root bus config accesses.
Link: https://lore.kernel.org/r/20200821035420.380495-12-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Now that DWC drivers can setup their own pci_ops for the root and child
buses, convert the Samsung Exynos driver to use the standard pci_ops for
root bus config accesses.
Link: https://lore.kernel.org/r/20200821035420.380495-11-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: linux-samsung-soc@vger.kernel.org
Now that DWC drivers can setup their own pci_ops for the root and child
buses, convert the HiSilicon Kirin driver to use the standard pci_ops
for root bus config accesses.
Link: https://lore.kernel.org/r/20200821035420.380495-10-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Xiaowei Song <songxiaowei@hisilicon.com>
Cc: Binghui Wang <wangbinghui@hisilicon.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Now that DWC drivers can setup their own pci_ops for the root and child
buses, convert the Amlogic meson driver to use the standard pci_ops for
root bus config accesses.
Link: https://lore.kernel.org/r/20200821035420.380495-9-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: linux-amlogic@lists.infradead.org
Now that DWC drivers can setup their own pci_ops for the root and child
buses, convert the Tegra driver to use the standard pci_ops for root
bus config accesses.
Link: https://lore.kernel.org/r/20200821035420.380495-8-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Now that DWC drivers can setup their own pci_ops for the root and child
buses, convert the TI Keystone driver to use the standard pci_ops for
config accesses.
Link: https://lore.kernel.org/r/20200821035420.380495-7-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Now that DWC drivers can setup their own pci_ops for the root and child
buses, convert the Amazon driver to use the standard pci_ops for child
bus config accesses.
Link: https://lore.kernel.org/r/20200821035420.380495-6-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jonathan Chocron <jonnyc@amazon.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The Designware root port config space is memory mapped accesses via the
DBI space by default. Add a common implementation
dw_pcie_own_conf_map_bus() for platforms to use.
Link: https://lore.kernel.org/r/20200821035420.380495-5-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
When devm_clk_get() returns -EPROBE_DEFER, i.MX6 PCI driver should
NOT print error message, use dev_err_probe() to handle it.
Link: https://lore.kernel.org/r/1597109364-4739-1-git-send-email-Anson.Huang@nxp.com
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Qsdk U-Boot can incorrectly leave the PCIe interface in an undefined
state if bootm command is used instead of bootipq. This is caused by the
not deinit of PCIe when bootm is called. Reset the PCIe before init
anyway to fix this U-Boot bug.
Link: https://lore.kernel.org/r/20200901124955.137-1-ansuelsmth@gmail.com
Fixes: 82a823833f ("PCI: qcom: Add Qualcomm PCIe controller driver")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: stable@vger.kernel.org # v4.19+
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Link: https://lore.kernel.org/r/20200818133739.463193-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Vidya Sagar <vidyas@nvidia.com>
Cc: Andrew Murray <amurray@thegoodpenguin.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-pci@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
In preparation to allow drivers to set their own root and child pci_ops
instead of using the DWC specific config space ops, we need to make
the pci_host_bridge pointer available and move setting the bridge->ops
and bridge->child_ops pointer to before the .host_init() hook.
Link: https://lore.kernel.org/r/20200821035420.380495-4-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The Designware DBI space contains the root bus bridge config space.
Platforms needing custom {rd,wr}_own_conf functions are also the ones
needing custom {read,write}_dbi ops functions and the access sequences
are the same.
Replace all dw_pcie_{rd,wr}_own_conf() calls with the DBI variants in
preparation to remove dw_pcie_{rd,wr}_own_conf().
Link: https://lore.kernel.org/r/20200821035420.380495-3-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The current check will result in the multiple function device
fails to initialize. So fix the check by masking out the
multiple function bit.
Link: https://lore.kernel.org/r/20200818092746.24366-1-Zhiqiang.Hou@nxp.com
Fixes: 0b24134f78 ("PCI: dwc: Add validation that PCIe core is set to correct mode")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
- Remove redundant logging for platform_get_irq() errors (Krzysztof
Wilczyński)
* pci/irq-error:
PCI: Remove dev_err() when handing an error from platform_get_irq()
- Use pci_host_bridge.windows list directly instead of splicing in a
temporary list for cadence, mvebu, host-common (Rob Herring)
- Use pci_host_probe() instead of open-coding all the pieces for altera,
brcmstb, iproc, mobiveil, rcar, rockchip, tegra, v3, versatile, xgene,
xilinx, xilinx-nwl (Rob Herring)
- Convert to devm_platform_ioremap_resource_byname() instead of open-coding
platform_get_resource_byname() and devm_ioremap_resource() for altera,
cadence, mediatek, rockchip, tegra, xgene (Dejin Zheng)
- Convert to devm_platform_ioremap_resource() instead of open-coding
platform_get_resource() and devm_ioremap_resource() for aardvark,
brcmstb, exynos, ftpci100, versatile (Dejin Zheng)
- Remove redundant error messages from devm_pci_remap_cfg_resource()
callers (Dejin Zheng)
- Drop useless PCI_ENABLE_PROC_DOMAINS from versatile driver (Rob Herring)
- Default host bridge parent device to the platform device (Rob Herring)
- Drop unnecessary zeroing of host bridge fields (Rob Herring)
- Use pci_is_root_bus() instead of tracking root bus number separately in
aardvark, designware (imx6, keystone, designware-host), mobiveil,
xilinx-nwl, xilinx, rockchip, rcar (Rob Herring)
- Set host bridge bus number in pci_scan_root_bus_bridge() instead of each
driver for aardvark, designware-host, host-common, mediatek, rcar, tegra,
v3-semi (Rob Herring)
- Use bridge resources instead of parsing DT 'ranges' again for cadence
(Rob Herring)
- Remove private bus number and range from cadence (Rob Herring)
- Use devm_pci_alloc_host_bridge() to simplify rcar (Rob Herring)
- Use struct pci_host_bridge.windows list directly rather than a temporary
(Rob Herring)
- Reduce OF "missing non-prefetchable window" from error to warning message
(Rob Herring)
- Convert rcar-gen2 from old Arm-specific pci_common_init_dev() to new
arch-independent interfaces (Rob Herring)
- Move DT resource setup into devm_pci_alloc_host_bridge() (Rob Herring)
- Set bridge map_irq and swizzle_irq to default functions; drivers that
don't support legacy IRQs (iproc) need to undo this (Rob Herring)
* pci/host-probe-refactor:
PCI: Set bridge map_irq and swizzle_irq to default functions
PCI: Move DT resource setup into devm_pci_alloc_host_bridge()
PCI: rcar-gen2: Convert to use modern host bridge probe functions
PCI: of: Reduce missing non-prefetchable memory region to a warning
PCI: rcar: Use struct pci_host_bridge.windows list directly
PCI: rcar: Use devm_pci_alloc_host_bridge()
PCI: cadence: Remove private bus number and range storage
PCI: cadence: Use bridge resources for outbound window setup
PCI: Move setting pci_host_bridge.busnr out of host drivers
PCI: rcar: Use pci_is_root_bus() to check if bus is root bus
PCI: rockchip: Use pci_is_root_bus() to check if bus is root bus
PCI: xilinx: Use pci_is_root_bus() to check if bus is root bus
PCI: xilinx-nwl: Use pci_is_root_bus() to check if bus is root bus
PCI: mobiveil: Use pci_is_root_bus() to check if bus is root bus
PCI: designware: Use pci_is_root_bus() to check if bus is root bus
PCI: aardvark: Use pci_is_root_bus() to check if bus is root bus
PCI: Drop unnecessary zeroing of bridge fields
PCI: Set default bridge parent device
PCI: versatile: Drop flag PCI_ENABLE_PROC_DOMAINS
PCI: controller: Remove duplicate error message
PCI: controller: Convert to devm_platform_ioremap_resource()
PCI: controller: Convert to devm_platform_ioremap_resource_byname()
PCI: xilinx: Use pci_host_probe() to register host
PCI: xilinx-nwl: Use pci_host_probe() to register host
PCI: rockchip: Use pci_host_probe() to register host
PCI: rcar: Use pci_host_probe() to register host
PCI: iproc: Use pci_host_probe() to register host
PCI: altera: Use pci_host_probe() to register host
PCI: xgene: Use pci_host_probe() to register host
PCI: versatile: Use pci_host_probe() to register host
PCI: v3: Use pci_host_probe() to register host
PCI: tegra: Use pci_host_probe() to register host
PCI: mobiveil: Use pci_host_probe() to register host
PCI: brcmstb: Use pci_host_probe() to register host
PCI: host-common: Use struct pci_host_bridge.windows list directly
PCI: mvebu: Use struct pci_host_bridge.windows list directly
PCI: cadence: Use struct pci_host_bridge.windows list directly
# Conflicts:
# drivers/pci/controller/cadence/pcie-cadence-host.c
The majority of DT based host drivers use the default .map_irq() and
.swizzle_irq() functions, so let's initialize the function pointers to
the default and drop setting them in the host drivers.
Drivers like iProc which don't support legacy interrupts need to set
.map_irq() back to NULL.
Link: https://lore.kernel.org/r/20200722022514.1283916-20-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Now that pci_parse_request_of_pci_ranges() callers just setup
pci_host_bridge.windows and dma_ranges directly and don't need the bus
range returned, we can just initialize them when allocating the
pci_host_bridge struct.
With this, pci_parse_request_of_pci_ranges() becomes a static function.
Link: https://lore.kernel.org/r/20200722022514.1283916-19-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The HiSilicon non-ECAM PCIe has been broken since March 2016 commit
7e57fd1444 ("PCI: designware: Move Root Complex setup code to
dw_pcie_setup_rc()"). The reason is this commit moved the iATU setup code
from dw_pcie_host_init() to dw_pcie_setup_rc(), but the hisi driver never
calls dw_pcie_setup_rc(). The result is the PCI memory space is never
configured and the driver can't work. It's also clear it has an iATU as
the config space accesses use it.
There's also no dts file using either "hisilicon,hip05-pcie" or
"hisilicon,hip06-pcie".
Link: https://lore.kernel.org/r/20200724224204.3249055-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Zhou Wang <wangzhou1@hisilicon.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Most host drivers only parse the DT bus range to set the root bus number
in pci_host_bridge.busnr. The ones that don't set busnr are buggy in
that they ignore what's in DT. Let's set busnr in pci_scan_root_bus_bridge()
where we already check for the bus resource and remove setting it in
host drivers.
Link: https://lore.kernel.org/r/20200722022514.1283916-12-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Will Deacon <will@kernel.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Ryder Lee <ryder.lee@mediatek.com>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: linux-tegra@vger.kernel.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-renesas-soc@vger.kernel.org
Use pci_is_root_bus() rather than tracking the root bus number to
determine if the bus is the root bus or not. This removes storing
duplicated data as well as the need for the host bridge driver to have
to care about the bus numbers in most cases.
Link: https://lore.kernel.org/r/20200722022514.1283916-6-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
The host bridge's parent device is always the platform device. As we
already have a pointer to it in the devres functions, let's initialize
the parent device. Drivers can still override the parent if desired.
Link: https://lore.kernel.org/r/20200722022514.1283916-3-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
devm_pci_remap_cfg_resource() will print an error message by itself when
goes wrong, so remove the duplicate error message.
Link: https://lore.kernel.org/r/20200526150954.4729-1-zhengdejin5@gmail.com
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Use devm_platform_ioremap_resource_byname() to simplify the code
since it contains platform_get_resource_byname() and
devm_ioremap_resource() respectively.
Link: https://lore.kernel.org/r/20200708164013.5076-1-zhengdejin5@gmail.com
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code, since t
contains platform_get_resource() and devm_ioremap_resource() calls
respectively.
Link: https://lore.kernel.org/r/20200708155614.308-1-zhengdejin5@gmail.com
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Lots of define are actually already defined in pci_regs.h, directly use
the standard defines.
Link: https://lore.kernel.org/r/20200615210608.21469-13-ansuelsmth@gmail.com
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Some SoC based on ipq8064/5 needs to be limited to pci GEN1 speed due to
some hardware limitations. Add support for speed setting defined by the
max-link-speed binding. If not defined the max speed is set to GEN2 by
default.
Link: https://lore.kernel.org/r/20200615210608.21469-12-ansuelsmth@gmail.com
Signed-off-by: Sham Muthayyan <smuthayy@codeaurora.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Ipq8064-v2 have tx term offset set to 0. Introduce this variant to permit
different offset based on the revision.
Link: https://lore.kernel.org/r/20200615210608.21469-10-ansuelsmth@gmail.com
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Add tx term offset support to pcie qcom driver need in some revision of
the ipq806x SoC. Ipq8064 needs tx term offset set to 7.
Link: https://lore.kernel.org/r/20200615210608.21469-9-ansuelsmth@gmail.com
Fixes: 82a823833f ("PCI: qcom: Add Qualcomm PCIe controller driver")
Signed-off-by: Sham Muthayyan <smuthayy@codeaurora.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: stable@vger.kernel.org # v4.5+
Set some specific value for Tx De-Emphasis, Tx Swing and Rx equalization
needed on some ipq8064 based device (Netgear R7800 for example). Without
this the system locks on kernel load.
Link: https://lore.kernel.org/r/20200615210608.21469-8-ansuelsmth@gmail.com
Fixes: 82a823833f ("PCI: qcom: Add Qualcomm PCIe controller driver")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: stable@vger.kernel.org # v4.5+
Rework 2.1.0 revision to use bulk clk api and fix missing assert on
reset_control_deassert error.
Link: https://lore.kernel.org/r/20200615210608.21469-7-ansuelsmth@gmail.com
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
The deinit issues reset_control_assert for PCI twice and does not contain
phy reset.
Link: https://lore.kernel.org/r/20200615210608.21469-4-ansuelsmth@gmail.com
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Aux and Ref clk are missing in PCIe qcom driver. Add support for this
optional clks for ipq8064/apq8064 SoC.
Link: https://lore.kernel.org/r/20200615210608.21469-2-ansuelsmth@gmail.com
Fixes: 82a823833f ("PCI: qcom: Add Qualcomm PCIe controller driver")
Signed-off-by: Sham Muthayyan <smuthayy@codeaurora.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code, thus a matching decrement is needed on
the error handling path to keep the counter balanced.
Link: https://lore.kernel.org/r/20200707055000.9453-1-dinghao.liu@zju.edu.cn
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
pm_runtime_get_sync() increments the runtime PM usage counter even
it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Link: https://lore.kernel.org/r/20200520084756.31620-1-dinghao.liu@zju.edu.cn
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Replace http:// links with https:// links. This reduces the likelihood of
man-in-the-middle attacks when developers open these links.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
[bhelgaas: also update samsung.com links, drop sourceforge link]
Link: https://lore.kernel.org/r/20200627103050.71712-1-grandmaster@al2klimov.de
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- Constify struct pci_ecam_ops (Rob Herring)
- Support building as modules (Rob Herring)
- Eliminate wrappers for pci_host_common_probe() by using DT match table
data (Rob Herring)
* remotes/lorenzo/pci/host-generic:
PCI: host-generic: Eliminate pci_host_common_probe wrappers
PCI: host-generic: Support building as modules
PCI: Constify struct pci_ecam_ops
# Conflicts:
# drivers/pci/controller/dwc/pcie-hisi.c
- Clarify that platform_get_irq() should never return 0 (Bjorn Helgaas)
- Check for platform_get_irq() failure consistently (Bjorn Helgaas)
- Replace zero-length array with flexible-array (Gustavo A. R. Silva)
- Unify pcie_find_root_port() and pci_find_pcie_root_port() (Yicong Yang)
- Quirk Intel C620 MROMs, which have non-BARs in BAR locations (Xiaochun
Lee)
- Fix pcie_pme_resume() and pcie_pme_remove() kernel-doc (Jay Fang)
- Rename _DSM constants to align with spec (Krzysztof Wilczyński)
* pci/misc:
PCI: Rename _DSM constants to align with spec
PCI/PME: Fix kernel-doc of pcie_pme_resume() and pcie_pme_remove()
x86/PCI: Mark Intel C620 MROMs as having non-compliant BARs
PCI: Unify pcie_find_root_port() and pci_find_pcie_root_port()
PCI: Replace zero-length array with flexible-array
PCI: Check for platform_get_irq() failure consistently
driver core: platform: Clarify that IRQ 0 is invalid
Add driver for the Socionext UniPhier Pro5 SoC endpoint controller.
This controller is based on the DesignWare PCIe core.
And add "host" to existing controller descriontions for the host controller
in Kconfig.
Link: https://lore.kernel.org/r/1589457801-12796-3-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Link: https://lore.kernel.org/r/20200521031355.7022-1-dinghao.liu@zju.edu.cn
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Vidya Sagar <vidyas@nvidia.com>
No functional change. Get "struct pcie_port *" from private data
pointer of "struct irq_domain" in dw_pcie_irq_domain_free() to make
it look similar to how "struct pcie_port *" is obtained in
dw_pcie_irq_domain_alloc()
Link: https://lore.kernel.org/r/20191220100550.777-1-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
The vim3l board does not work with a standard PCIe switch (ASM1184e),
spitting all kind of errors - hinting at HW misconfiguration (no link,
port enumeration issues, etc).
According to the the Synopsys DWC PCIe Reference Manual, in the section
dedicated to the PLCR register, bit 7 is described (FAST_LINK_MODE) as:
"Sets all internal timers to fast mode for simulation purposes."
it is sound to set this bit from a simulation perspective, but on actual
silicon, which expects timers to have a nominal value, it is not.
Make sure the FAST_LINK_MODE bit is cleared when configuring the RC
to solve this problem.
Link: https://lore.kernel.org/r/20200429164230.309922-1-maz@kernel.org
Fixes: 9c0ef6d34f ("PCI: amlogic: Add the Amlogic Meson PCIe controller driver")
Signed-off-by: Marc Zyngier <maz@kernel.org>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
