[Why & How]
Due to how pmfw fills out the table when dcfclk states are disabled,
using dcfclk based clk table would cause a no read situation.
Revert the change to prevent underflow until a better solution is coded.
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
- add debug option to bypass ssinfo from bios.
- Refactor fixed VS logic for non-transparent mode
- add cable ID support for usb c connector
- clear remote dc_sink when stop mst
- Ignore Transitional Invalid Link Rate Error Message
- Fix wrong resolution with DP/VGA adapter
- Refactor PSR DPCD caps detection
- Set compbuf size to min at prep prevent overbook crb
- lock/un-lock cursor if odm pipe split used
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
All fixed VS/PE link training sequence should be refactored
into a separate function outside of the standard link training
sequence. This includes the sequence for non-transparent
mode.
[How]
Isolate link training sequence for fixed VS/PE non-transparent
mode into a separate function.
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: George Shen <George.Shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently, we don't have code path to release remote dc_sink when unplug
MST hub from the system. After few times hotplug, we hit the limition of
maximum number of remote dc_sink and can't light up new connected monitor
anymore.
[How]
Releasing all remote dc_sink at dm_helpers_dp_mst_stop_top_mgr() was
removed by previous patch. Restore it.
Reviewed-by: Jerry Zuo <Jerry.Zuo@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When hotplug or unplug happens, each stream disabled one by one, and then
enable any alived streams. Link phy and payload table is cleared when 1st
stream is disabled. That causes the error message pops up when disable 2nd
stream. There is no active stream after link_rate is cleared.
After all streams are disabled, link will be trained again and link rate is
assigned to any alived streams.
Therefore there is no harm for the error message that represents invalid
link rate value in the atomic reset transitional time period.
[How]
Downgrade the log level from ERROR to DEBUG.
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Hotplugging the VGA side of some DP/VGA adapters caused the display to
light up with the wrong (non-native) resolution.
This is caused by the adapter misbehaving by reporting the wrong number
of downstream ports when the VGA side is unplugged (reports 1 instead of
0), but only if the SINK_COUNT DPCD register is read more than once.
[How]
To work around the adapter behavior, remove the sink if link is
detected, but EDID cannot be read.
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Ilya <Ilya.Bakoulin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Detbuffer size is dynamically set for dcn31x. At certain moment,
compbuf+(def size * num pipes) > config return buffer size causing
flickering. This is easily reproducible when MPO is
enabled with two displays.
[How]
At prepare BW, use the min comp buffer size. When it is to
optimize BW, set compbuf size back to maximum possible size.
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Duncan Ma <duncanma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When system resume from sleep, the cursor lock will be reset
to default(lock status). And the cursor programming sequence
doesn't consider about odm pipe split cause cursor can't be
enabled.
[How]
If odm pipe split has been used, lock/un-lock on each pipes.
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Turn previously global functions into static functions to avoid
-Wmissing-prototype warnings, such as:
drivers/gpu/drm/amd/amdgpu/../display/dc/irq/dcn30/irq_service_dcn30.c:50:20:
warning: no previous prototype for function 'to_dal_irq_source_dcn30'
[-Wmissing-prototypes]
enum dc_irq_source to_dal_irq_source_dcn30(
^
drivers/gpu/drm/amd/amdgpu/../display/dc/irq/dcn30/irq_service_dcn30.c:50:1:
note: declare 'static' if the function is not intended to be used outside
of this translation unit
enum dc_irq_source to_dal_irq_source_dcn30(
^
static
1 warning generated.
drivers/gpu/drm/amd/amdgpu/../display/dc/clk_mgr/dcn316/dcn316_clk_mgr.c:488:6:
warning: no previous prototype for function
'dcn316_clk_mgr_helper_populate_bw_params' [-Wmissing-prototypes]
void dcn316_clk_mgr_helper_populate_bw_params(
^
drivers/gpu/drm/amd/amdgpu/../display/dc/clk_mgr/dcn316/dcn316_clk_mgr.c:488:1:
note: declare 'static' if the function is not intended to be used outside
of this translation unit
void dcn316_clk_mgr_helper_populate_bw_params(
^
static
1 warning generated.
v2: drop is_timing_changed hunk (Alex)
Signed-off-by: Maíra Canal <maira.canal@usp.br>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Include the header with the prototype to silence the following clang
warning:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn201/dcn201_init.c:127:6:
warning: no previous prototype for function 'dcn201_hw_sequencer_construct'
[-Wmissing-prototypes]
void dcn201_hw_sequencer_construct(struct dc *dc)
^
Signed-off-by: Maíra Canal <maira.canal@usp.br>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove the variable clamshell_closed from the function
dcn10_align_pixel_clocks.
This was pointed by clang with the following warning:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_hw_sequencer.c:2063:7:
warning: variable 'clamshell_closed' set but not used
[-Wunused-but-set-variable]
bool clamshell_closed = false;
^
Signed-off-by: Maíra Canal <maira.canal@usp.br>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove the unused struct irq_source_info_funcs
dmub_outbox_irq_info_funcs from the file, which was declared but never
hooked up.
This was pointed by clang with the following warning:
drivers/gpu/drm/amd/amdgpu/../display/dc/irq/dcn201/irq_service_dcn201.c:141:43:
warning: unused variable 'dmub_outbox_irq_info_funcs'
[-Wunused-const-variable]
static const struct irq_source_info_funcs dmub_outbox_irq_info_funcs = {
^
Signed-off-by: Maíra Canal <maira.canal@usp.br>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove dcn316_smu_set_voltage_via_phyclk function, which is not used in the
codebase.
This was pointed by clang with the following warning:
drivers/gpu/drm/amd/amdgpu/../display/dc/clk_mgr/dcn316/dcn316_smu.c:171:5:
warning: no previous prototype for function
'dcn316_smu_set_voltage_via_phyclk' [-Wmissing-prototypes]
int dcn316_smu_set_voltage_via_phyclk(struct clk_mgr_internal *clk_mgr, int
requested_phyclk_khz)
^
Signed-off-by: Maíra Canal <maira.canal@usp.br>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove unused temp variable from the dmub_rb_flush_pending function by
using arithmetic to remove the loop.
The -Wunused-but-set-variable warning was pointed out by Clang with the
following warning:
drivers/gpu/drm/amd/amdgpu/../display/dmub/inc/dmub_cmd.h:2921:12: warning:
variable 'temp' set but not used [-Wunused-but-set-variable]
uint64_t temp;
^
v2: squash in revert and comment update (Alex)
Signed-off-by: Maíra Canal <maira.canal@usp.br>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Rather than duplicating the logic in two places,
consolidate the logic in the display manager.
Acked-by: Yifan Zhang <yifan1.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Separate the logic for each of these features to make the
code easier to understand and update in the future.
Acked-by: Yifan Zhang <yifan1.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- set DC version
- add construct/destroy dc clock management function
- register dcn interrupt handler
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Even if PSR is allowed for a present GPU, there might be no eDP link
which supports PSR.
Fixes: 7089784873 ("drm/amdgpu/display: Only set vblank_disable_immediate when PSR is not enabled")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Michel Dänzer <mdaenzer@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The previous change:
"Add affected crtcs to atomic state for dsc mst unplug"
forces modeset on all added crctc regardless whether timing changed or not.
Per our implementation of dsc we need modeset only if timing changed.
Otherwise dsc can be programmed incorrectly leading to dsc engine hang.
[How]
During atomic_check pre-compute dsc params.
Only set mode_changed if timing is changed.
Reviewed-by: Hersen Wu <hersenwu@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
payload and slot number of display on dsc mst hub will be
adjusted when there is change on any display on dsc hub.
to monitor dsc enable/disable, pbn change, we need add log.
[How]
add mst_pbn to dc_dsc_config of dc_crtc_timing.
add dsc, pbn, display name within dc_core_enable_stream,
dc_core_disable_stream, dc_stream_log
Reviewed-by: Jerry Zuo <Jerry.Zuo@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Hersen Wu <hersenwu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along the following fixes:
-Fixes bugs for dsc mst hub
-Enables 29 denial itnerface by default
-Fixes dmub outbox notificatoin
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When display topology changed on DSC hub we add all crtcs with dsc support to
atomic state.
Refer to patch:"drm/amd/display: Trigger modesets on MST DSC connectors"
However the original implementation may skip crtc if the topology change
caused by unplug.
That potentially could lead to no-lightup or corruption on DSC hub after
unplug event on one of the connectors.
[How]
Update add_affected_mst_dsc_crtcs() to use old connector state
if new connector state has no crtc (undergoes modeset due to unplug)
Fixes: 44be939ff7 ("drm/amd/display: Trigger modesets on MST DSC connectors")
Reviewed-by: Hersen Wu <hersenwu@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
display mapping change will involved pipe power gating on and off.
when doing this too fase, sometimes usbc will have no display.
check HW status, it is still in pipe power gating.
[how]
insert polling HW status to make sure the required state reached.
also add dal registry key handling.
Reviewed-by: Sung joon Kim <Sungjoon.Kim@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
when unplug 1 dp from dsc mst hub, atomic_check new request
dc_state only include info for the unplug dp. this will not
trigger re-compute pbn for displays still connected to hub.
[how] all displays connected to dsc hub are available in
dc->current_state, by comparing dc->current_state and new
request from atomic_chceck, it will provide info of
displays connected to hub and do pbn re-compute.
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Hersen Wu <hersenwu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently driver enables dmub outbox notification before oubox ISR is
registered. During boot scenario, sometimes dmub issues hpd outbox
message before driver registers ISR and those messages are missed.
[How]
Enable dmub outbox notification after outbox ISR is registered. Also,
restructured outbox enable code to call from dm layer and renamed APIs.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For DCN3/3.01/3.02 at least these use the fpu.
v2: squash in build fix for when DCN is not enabled (Leo)
Signed-off-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In LTTPR non-transparent mode, we need
to reset the cached lane settings before performing
link training on the next PHY repeater. Otherwise,
the cached lane settings will be used for the next
clock recovery e.g. VS = MAX (3) which should not be
the case according to the DP specs. We expect to use
minimum lane settings on each clock recovery sequence.
[how]
Reset DPCD and HW lane settings on each repeater LT.
Set training pattern to 0 for the repeater that failed LT
at the proper place.
Reviewed-by: Meenakshikumar Somasundaram <Meenakshikumar.Somasundaram@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amd-drm-next-5.18-2022-02-11-1:
amdgpu:
- Clean up of power management code
- Enable freesync video mode by default
- Clean up of RAS code
- Improve VRAM access for debug using SDMA
- Coding style cleanups
- SR-IOV fixes
- More display FP reorg
- TLB flush fixes for Arcuturus, Vega20
- Misc display fixes
- Rework special register access methods for SR-IOV
- DP2 fixes
- DP tunneling fixes
- DSC fixes
- More IP discovery cleanups
- Misc RAS fixes
- Enable both SMU i2c buses where applicable
- s2idle improvements
- DPCS header cleanup
- Add new CAP firmware support for SR-IOV
amdkfd:
- Misc cleanups
- SVM fixes
- CRIU support
- Clean up MQD manager
UAPI:
- Add interface to amdgpu CTX ioctl to request a stable power state for profiling
https://gitlab.freedesktop.org/mesa/drm/-/merge_requests/207
- Add amdkfd support for CRIU
https://github.com/checkpoint-restore/criu/pull/1709
- Remove old unused amdkfd debugger interface
Was only implemented for Kaveri and was only ever used by an old HSA tool that was never open sourced
radeon:
- Fix error handling in radeon_driver_open_kms
- UVD suspend fix
- Misc fixes
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220211220706.5803-1-alexander.deucher@amd.com
