Allow untrusted VF to add 16 unicast/multicast filters. VF uses 1 filter
for the default/perm_addr/LAA MAC, 1 for broadcast, and 16 additional
unicast/multicast filters.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently a user is not allowed to clear a VF's administratively set MAC
on the PF. Fix this by allowing an all zero MAC address via "ip link set
${pf_eth} vf ${vf_id} mac 00:00:00:00:00:00".
An example use case for this would be issuing a "virsh shutdown"
command on a VM. The call to iproute mentioned above is part of this flow.
Without this change the driver incorrectly rejects clearing the VF's
administratively set MAC and prints unhelpful log messages.
Also, improve the comments surrounding this change.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently when a VF VSI calls ice_vsi_release() and ice_vsi_setup() it
subsequently clears/sets the VF cached variables for lan_vsi_idx and
lan_vsi_num. This works fine, but can be improved by handling this in
the VF specific VSI release and setup functions.
Also, when a VF VSI is setup too many parameters are passed that can be
derived from the VF. Fix this by only calling VF VSI setup with the bare
minimum parameters.
Also, add functionality to invalidate a VF's VSI when it's released
and/or setup fails. This will make it so a VF VSI cannot be accessed via
its cached vsi_idx/vsi_num in these cases.
Finally when a VF's VSI is invalidated set the lan_vsi_idx and
lan_vsi_num to ICE_NO_VSI to clearly show that there is no valid VSI
associated with this VF.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently VF VSI are being reset twice during a PFR or greater. This is
causing reset, specifically resetting all VFs, to take too long. This is
causing various issues with VF drivers not being able to gracefully
handle the VF reset timeout. Fix this by refactoring how VF reset is
handled for the case mentioned previously and for the VFR/VFLR case.
The refactor was done by doing the following:
1. Removing the call to ice_vsi_rebuild_by_type for
ICE_VSI_VF VSI, which was causing the initial VSI rebuild.
2. Adding functions for pre/post VSI rebuild functions that can be called
in both the reset all VFs case and reset individual VF case.
3. Adding VSI rebuild functions that are specific for the reset all VFs
case and adding functions that are specific for the reset individual
VF case.
4. Calling the pre-rebuild function, then the specific VSI rebuild
function based on the reset type, and then calling the post-rebuild
function to handle VF resets.
This patch series makes some assumptions about how VSI are handling by
FW during reset:
1. During a PFR or greater all VSI in FW will be cleared.
2. During a VFR/VFLR the VSI rebuild responsibility is in the hands of
the PF software.
3. There is code in the ice_reset_all_vfs() case to amortize operations
if possible. This was left intact.
4. PF software should not be replaying VSI based filters that were added
other than host configured, PF software configured, or the VF's
default/LAA MAC. This is the VF drivers job after it has been reset.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove VM/VF disable AQC (opcode 0x0C31) when resetting all VFs.
This is not required for CORER/GLOBR reset.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When resetting a VF the VLAN and MAC filter configurations need to be
replayed. Add helper functions for this purpose.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As the title says, use a function to set trust mode bit on reset.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some function names weren't very clear and some portions of VF creation
could be moved into functions for clarity. Fix this by renaming some
functions and move pieces of code into clearly name functions.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the same flow is used for VF VSI initialization/creation and VF
VSI reset. This makes the initialization/creation flow unnecessarily
complicated. Fix this by separating the initialization/creation of the
VF VSI from the reset flow.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Create a helper function for clearing VPGEN_VFRTRIG as this needs to be
done on reset to notify the VF that we are done resetting it. Also, it
needs to be done on SR-IOV initialization/creation in case it was left
in a bad state after SR-IOV tear down.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a new function for checking if SR-IOV can be configured based on
the PF and/or device's state/capabilities. Also, simplify the flow in
ice_sriov_configure().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently ice_ena_vf_mappings() does all of the VF's MSIX and queue
mapping in one function. This makes it hard to digest. Fix this by
creating a new function for enabling MSIX mappings and one for enabling
queue mappings.
Also, rename some variables in the functions for clarity.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_get_pfa_module_tlv() and ice_read_sr_word() are not being called
outside of their file. Declare them as static.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If register_netdev() fails, the driver will attempt to cleanup the
q_vectors and inadvertently trigger a kernel BUG due to a NULL pointer
dereference.
This occurs because cleaning up q_vectors attempts to call
netif_napi_del on napi_structs which were never initialized.
Resolve this by releasing the netdev in ice_cfg_netdev and setting
vsi->netdev to NULL. This ensures that after ice_cfg_netdev fails the
state is rewound to match as if ice_cfg_netdev was never called.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If ice_init_interrupt_scheme fails, ice_probe will jump to clearing up
the interrupts. This can lead to some static analysis tools such as the
compiler sanitizers complaining about double free problems.
Since ice_init_interrupt_scheme already unrolls internally on failure,
there is no need to call ice_clear_interrupt_scheme when it fails. Add
a new unroll label and use that instead.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove an unnecessary copy of vsi->info into ctxt->info in ice_vsi_init.
This line is essentially a no-op because ice_set_dflt_vsi_ctx performs
a memset to clear the info from the context structure.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are certain cases where the DDP load fails and the FW issues a
core reset. For these cases, wait for reset to complete before
proceeding with reset of the driver init.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If a UMEM is present on a queue when an interface/queue pair is being
enabled, the driver will try to prepare the Rx buffers in advance to
improve performance. However, if fill queue is shorter than HW Rx ring,
the driver will report failure after getting the last address from the
fill queue.
This still lets the driver process the packets correctly during the NAPI
poll, but leads to a constant NAPI rescheduling. Not allocating the
buffers in advance would result in a potential performance decrease.
Commit d57d76428a ("xsk: Add API to check for available entries in FQ")
provides an API that lets drivers check the number of addresses that the
fill queue holds.
Notify the user if fill queue is not long enough to prepare all buffers
before packet processing starts, and allocate the buffers during the
NAPI poll. If the fill queue size is sufficient, prepare Rx buffers in
advance.
Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We don't need both rx_status and rx_error parameters, as the latter is
a subset of the former. Remove rx_error completely and check the right bit
in rx_status.
Rename rx_status to rx_status0, and rx_status_err1 to
rx_status1. This naming more closely reflects the specification.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When writing the driver's struct ice_tlan_ctx structure, do not write the
8-bit element int_q_state with the associated internal-to-hardware field
which is 122-bits, otherwise the helper function ice_write_byte() will use
undefined behavior when setting the mask used for that write. This should
not cause any functional change and will avoid use of undefined behavior.
Also, update a comment to highlight this structure element is not written.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In current implementation number of XDP Tx queues is the same as
the number of transmit queues, which is not always true. This
patch changes this number to match the number of receive queues.
XDP programs are running on Rx rings, so what we actually need to
provide is the XDP Tx ring per each Rx ring so that the whole XDP
ecosystem is functional, e.g. if the result of XDP prog is XDP_TX
then you have the need to access the XDP Tx ring.
Signed-off-by: Marta Plantykow <marta.a.plantykow@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When XDP Tx program is loaded and packets are sent from
interface, VSI statistics are not updated. This patch adds
packets sent on Tx XDP ring to VSI ring stats.
Signed-off-by: Marta Plantykow <marta.a.plantykow@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When XDP Tx rings are destroyed the number of XDP Tx queues
is not changing. This patch is changing this number to 0.
Signed-off-by: Marta Plantykow <marta.a.plantykow@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A race condition between FW and SW can occur between admin queue setup and
the first command sent. A link event may occur and FW attempts to notify a
non-existent queue. FW will set the critical error bit and disable the
queue. When this happens retry queue setup.
Signed-off-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, if the PVID is set in the VLAN handling section of the VSI
context the driver still allows VLAN stripping to be enabled/disabled.
VLAN stripping should only be modifiable when the PVID is not set. Fix
this by preventing VLAN stripping modification when PVID is set.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently we are only including illegal_bytes and rx_crc_errors in the
PF netdev's rx_error counter. There are many more causes of Rx errors
that the device supports and reports via Ethtool. Accumulate all Rx
errors in the PF netdev's rx_error counter.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Handle memory leaks during control queue initialization and
buffer allocation failures. The macro ICE_FREE_CQ_BUFS is modified to
re-use for this fix.
Signed-off-by: Surabhi Boob <surabhi.boob@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The manage MAC write command was implemented in an overly complex way
that actually didn't work, as it wasn't symmetric to the manage MAC
read command, and was feeding bytes out of order to the firmware. Fix
the implementation by just using a simple array to represent the MAC
address when it is being written via firmware command.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove is_zero_ether_add() check when setting the VF default LAN address.
This check assumed that the address had been delete and zeroed before
calling ice_vc_add_mac_addr(). Now the default LAN address will be set
to the last unicast MAC address added by the VF.
The default LAN address is reported by the PF via ndo_get_vf_config.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver had an unused define that can be removed. Found by
compiler -Werror=unused-macros check.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix the remaining signed vs unsigned issues, which appear
when compiling with -Werror=sign-compare.
Many of these are because there is an external interface that is passing
an int to us (which we can't change) but that we (rightfully) store
and compare against as an unsigned in our data structures.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2020-05-22
This series contains updates to virtchnl and the ice driver.
Geert Uytterhoeven fixes a data structure alignment issue in the
virtchnl structures.
Henry adds Flow Director support which allows for the redirection on
ntuple rules over six patches. Initially Henry adds the initial
infrastructure for Flow Director, and then later adds IPv4 and IPv6
support, as well as being able to display the ntuple rules.
Bret add Accelerated Receive Flow Steering (aRFS) support which is used
to steer receive flows to a specific queue. Fixes a transmit timeout
when the VF link transitions from up/down/up because the transmit and
receive queue interrupts are not enabled as part of VF's link up. Fixed
an issue when the default VF LAN address is changed and after reset the
PF will attempt to add the new MAC, which fails because it already
exists. This causes the VF to be disabled completely until it is removed
and enabled via sysfs.
Anirudh (Ani) makes a fix where the ice driver needs to call set_mac_cfg
to enable jumbo frames, so ensure it gets called during initialization
and after reset. Fix bad register reads during a register dump in
ethtool by removing the bad registers.
Paul fixes an issue where the receive Malicious Driver Detection (MDD)
auto reset message was not being logged because it occurred after the VF
reset.
Victor adds a check for compatibility between the Dynamic Device
Personalization (DDP) package and the NIC firmware to ensure that
everything aligns.
Jesse fixes a administrative queue string call with the appropriate
error reporting variable. Also fixed the loop variables that are
comparing or assigning signed against unsigned values.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix loop variables that are comparing or assigning signed against
unsigned values, mostly by declaring loop counters as unsigned.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was using rq_last_status where it should have been
using sq_last_status. Fix the string to be using the correct
error reporting variable.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The "ethtool -d" handler reads registers in the ice_regs_dump_list array
and returns read values back to the userspace.
The register offsets PFINT0_ITR* are not valid as per the specification
and reading these causes a "unable to handle kernel paging request" bug
in the driver. Remove these registers from ice_regs_dump_list.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Require the Dynamic Device Personalization (DDP) file to have the same
major version number and the same or older minor number than the firmware
version major and minor, respectively.
Check the OS and NVM package versions before downloading the package.
If the OS package version is not compatible with NVM then return an
appropriate error.
Split the 32-byte segment name into a 28-byte segment name and
a 4-byte Track-ID. Older packages will still work with this change
because no package has a name that will take up more than 28 bytes;
in this case the Track-ID will be 0.
Note that the driver will store the segment name as 32-bytes in the
ice_hw structure, in order to normalize the length of the various
package name strings that it uses.
Also add section ID and structure for the segment metadata section.
Signed-off-by: Victor Raj <victor.raj@intel.com>
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently if a unicast MAC is set via ndo_set_vf_mac, the PF driver will
set the VF's dflt_lan_addr.addr once some basic checks have passed. The
VF is then reset. During reset the PF driver will attempt to program the
VF's MAC from the dflt_lan_addr.addr field. This fails when the MAC
already exists on the PF's switch.
This is causing the VF to be completely disabled until removing/enabling
any VFs via sysfs.
Fix this by checking if the unicast MAC exists before triggering a VF
reset directly in ndo_set_vf_mac. Also, add a check if the unicast MAC
is set to the same value as before and return 0 if that is the case.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently if the iavf is loaded and a VF link transitions from up to
down to up again a Tx timeout will be triggered. This happens because
Tx/Rx queue interrupts are only enabled when receiving the
VIRTCHNL_OP_CONFIG_MAP_IRQ message, which happens on reset or initial
iavf driver load, but not when bringing link up. This is problematic
because they are disabled on the VIRTCHNL_OP_DISABLE_QUEUES message,
which is part of bringing a VF's link down. However, they are not
enabled on the VIRTCHNL_OP_ENABLE_QUEUES message, which is part of
bringing a VF's link up.
Fix this by re-enabling the VF's Rx and Tx queue interrupts when they
were previously configured. This is done by first checking to make
sure the previous value in QINT_[R|T]QCTL.MSIX_INDX is not 0, which
is used to represent the OICR in the VF's interrupt space. If the
MSIX_INDX is non-zero then enable the interrupt by setting the
QINT_[R|T]CTL.CAUSE_ENA bit to 1.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rx MDD auto reset message was not being logged because logging occurred
after the VF reset and the VF MDD data was reinitialized.
Log the Rx MDD auto reset message before triggering the VF reset.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As per the specification, the driver needs to call set_mac_cfg
(opcode 0x0603) to be able to exercise jumbo frames. Call the
function during initialization and the post reset rebuild flow.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enable accelerated Receive Flow Steering (aRFS). It is used to steer Rx
flows to a specific queue. This functionality is triggered by the network
stack through ndo_rx_flow_steer and requires Flow Director (ntuple on) to
function.
The fltr_info is used to add/remove/update flow rules in the HW, the
fltr_state is used to determine what to do with the filter with respect
to HW and/or SW, and the flow_id is used in co-ordination with the
network stack.
The work for aRFS is split into two paths: the ndo_rx_flow_steer
operation and the ice_service_task. The former is where the kernel hands
us an Rx SKB among other items to setup aRFS and the latter is where
the driver adds/updates/removes filter rules from HW and updates filter
state.
In the Rx path the following things can happen:
1. New aRFS entries are added to the hash table and the state is
set to ICE_ARFS_INACTIVE so the filter can be updated in HW
by the ice_service_task path.
2. aRFS entries have their Rx Queue updated if we receive a
pre-existing flow_id and the filter state is ICE_ARFS_ACTIVE.
The state is set to ICE_ARFS_INACTIVE so the filter can be
updated in HW by the ice_service_task path.
3. aRFS entries marked as ICE_ARFS_TODEL are deleted
In the ice_service_task path the following things can happen:
1. New aRFS entries marked as ICE_ARFS_INACTIVE are added or
updated in HW.
and their state is updated to ICE_ARFS_ACTIVE.
2. aRFS entries are deleted from HW and their state is updated
to ICE_ARFS_TODEL.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Madhu Chittim <madhu.chittim@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Following a reset, Flow Director filters are cleared from the hardware.
Rebuild the filters using the software structures containing the filter
rules.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Flex-bytes allows for packet matching based on an offset and value. This
is supported via the ethtool user-def option. It is specified by providing
an offset followed by a 2 byte match value. Offset is measured from the
start of the MAC address.
The following restrictions apply to flex-bytes. The specified offset must
be an even number and be smaller than 0x1fe.
Example usage:
ethtool -N eth0 flow-type tcp4 src-ip 192.168.0.55 dst-ip 172.16.0.55 \
src-port 12 dst-port 13 user-def 0x10ffff action 32
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add functionality for ethtool --show-ntuple, allowing for filters to be
displayed when set functionality is added. Add statistics related to
Flow Director matches and status.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Flow Director allows for redirection based on ntuple rules. Rules are
programmed using the ethtool set-ntuple interface. Supported actions are
redirect to queue and drop.
Setup the initial framework to process Flow Director filters. Create and
allocate resources to manage and program filters to the hardware. Filters
are processed via a sideband interface; a control VSI is created to manage
communication and process requests through the sideband. Upon allocation of
resources, update the hardware tables to accept perfect filters.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-05-23
The following pull-request contains BPF updates for your *net-next* tree.
We've added 50 non-merge commits during the last 8 day(s) which contain
a total of 109 files changed, 2776 insertions(+), 2887 deletions(-).
The main changes are:
1) Add a new AF_XDP buffer allocation API to the core in order to help
lowering the bar for drivers adopting AF_XDP support. i40e, ice, ixgbe
as well as mlx5 have been moved over to the new API and also gained a
small improvement in performance, from Björn Töpel and Magnus Karlsson.
2) Add getpeername()/getsockname() attach types for BPF sock_addr programs
in order to allow for e.g. reverse translation of load-balancer backend
to service address/port tuple from a connected peer, from Daniel Borkmann.
3) Improve the BPF verifier is_branch_taken() logic to evaluate pointers
being non-NULL, e.g. if after an initial test another non-NULL test on
that pointer follows in a given path, then it can be pruned right away,
from John Fastabend.
4) Larger rework of BPF sockmap selftests to make output easier to understand
and to reduce overall runtime as well as adding new BPF kTLS selftests
that run in combination with sockmap, also from John Fastabend.
5) Batch of misc updates to BPF selftests including fixing up test_align
to match verifier output again and moving it under test_progs, allowing
bpf_iter selftest to compile on machines with older vmlinux.h, and
updating config options for lirc and v6 segment routing helpers, from
Stanislav Fomichev, Andrii Nakryiko and Alan Maguire.
6) Conversion of BPF tracing samples outdated internal BPF loader to use
libbpf API instead, from Daniel T. Lee.
7) Follow-up to BPF kernel test infrastructure in order to fix a flake in
the XDP selftests, from Jesper Dangaard Brouer.
8) Minor improvements to libbpf's internal hashmap implementation, from
Ian Rogers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
To make the function easier to identify as being part of the ice driver,
prepend ice to the function name.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Self-explanatory.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The variable status cannot be zero due to a prior check of it; remove this
check.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The else conditional expression is always true due to the if conditional
expression; remove it and add a comment to make it obvious still.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In function ice_set_mac_address, we will remove old dev_addr before
adding the new MAC. In the removing and adding process of the MAC,
there is no need to return error if the check finds the to-be-removed
dev_addr does not exist in the MAC filter list or the to-be-added mac
already exists, keep going or return success accordingly.
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move filter functions to separate file.
Add functions that prepare suitable ice_fltr_info struct
depending on the filter type and add this struct to earlier created
list:
- ice_fltr_add_mac_to_list
- ice_fltr_add_vlan_to_list
- ice_fltr_add_eth_to_list
This functions are used in adding and removing filters.
Create wrappers for functions mentioned above that alloc list,
add suitable ice_fltr_info to it and call add or remove function.
- ice_fltr_prepare_mac
- ice_fltr_prepare_mac_and_broadcast
- ice_fltr_prepare_vlan
- ice_fltr_prepare_eth
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Memory allocated in the ice_add_prof_id_vsig() function wasn't being
properly freed if an error occurred inside the for-loop in the function.
In particular, 'p' wasn't being freed if an error occurred before it was
added to the resource list at the end of the for-loop.
Signed-off-by: Eric Joyner <eric.joyner@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The vf_id variable is dealt with in the code in inconsistent
ways of sign usage, preventing compilation with -Werror=sign-compare.
Fix this problem in the code by always treating vf_id as unsigned, since
there are no valid values of vf_id that are negative.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change min() macros to min_t() which has compare type specified and it
helps avoid precision loss.
In some cases there was precision loss during calls or assignments.
Some fields in structs were unnecessarily large and gave multiple
warnings.
There were also some minor type differences which are now fixed as well as
some cases where a simple cast was needed.
Callers were were passing data that is a u16 to
ice_sched_cfg_node_bw_alloc() but the function was truncating that to a u8.
Fix that by changing the function to take a u16.
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When printing the ice status or AQ error codes, instead of printing out the
numerical value, provide the description of the error code. This provides
more info about the issue than a number.
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As soon as the driver registers the PF netdev, userspace utilities
like NetworkManager try to bring up the associated interface. When
this happens, the driver may not have finished initializing fully,
resulting in a bunch of errors in the interface up flow.
The driver already has a mechanism to indicate if it's not up yet;
by setting the __ICE_DOWN bit in pf->state, but this bit gets
cleared too early in the current flow. So clear this bit only when
the driver is fully up. Also check for the same bit in the ice_open
flow, and return -EBUSY if the bit is set.
Also in ice_open, replace references of vsi->back with a local
variable.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, the ice driver is setting a PHY configuration,
which causes a link drop, and then additionally it calls
for a nway_reset, which restarts auto-negotiation on the
link, which also causes a link drop. These two link
events in such close timing is causing the FW to not be
able to generate a link interrupt for the driver to
respond to.
Remove the unnecessary auto-negotiation restart from the
set pauseparams flow. Also remove error path that
would have performed an ice_down/ice_up as that is
also unnecessary.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current implementation for contiguous TC check
is assuming that the UPs will be mapped to TCs in
a linear progressing fashion. This is obviously
not always true.
Change the check to allow for various UP2TC mapping
configurations.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When there's a Tx timeout for a queue which belongs to a PFC enabled TC,
then it's not because the queue is hung but because PFC is in action.
In PFC, peer sends a pause frame for a specified period of time when its
buffer threshold is exceeded (due to congestion). Netdev on the other
hand checks if ACK is received within a specified time for a TX packet, if
not, it'll invoke the tx_timeout routine.
Signed-off-by: Avinash JD <avinash.dayanand@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement promiscuous support for VF VSIs. Behaviour of promiscuous support
is based on VF trust as well as the, introduced, vf-true-promisc flag.
A trusted VF with vf-true-promisc disabled will be the default VSI, which
means that all traffic without a matching destination MAC address in the
device's internal switch will be forwarded to this VF VSI.
A trusted VF with vf-true-promisc enabled will go into "true promiscuous
mode". This amounts to the VF receiving all ingress and egress traffic
that hits the device's internal switch.
An untrusted VF will only receive traffic destined for that VF.
The vf-true-promisc-support flag cannot be toggled while any VF is in
promiscuous mode. This flag should be set prior to loading the iavf driver
or spawning VF(s).
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Create a boost TCAM entry for each tunnel port in order to get a tunnel
PTYPE. Update netdev feature flags and implement the appropriate logic to
get and set values for hardware offloads.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The flash memory for the ice hardware contains a block of information
used for link management called the Netlist module.
As this essentially represents another section of firmware, add its
version information to the output of the driver's .info_get handler.
This includes both a version and the first few bytes of a hash of the
module contents.
fw.netlist -> the version information extracted from the netlist module
fw.netlist.build-> first 4 bytes of the hash of the contents, similar
to fw.mgmt.build
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove MEM_TYPE_ZERO_COPY in favor of the new MEM_TYPE_XSK_BUFF_POOL
APIs.
v4->v5: Fixed "warning: Excess function parameter 'alloc' description
in 'ice_alloc_rx_bufs_zc'" and "warning: Excess function
parameter 'xdp' description in
'ice_construct_skb_zc'". (Jakub)
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: intel-wired-lan@lists.osuosl.org
Link: https://lore.kernel.org/bpf/20200520192103.355233-10-bjorn.topel@gmail.com
Move the AF_XDP zero-copy driver interface to its own include file
called xdp_sock_drv.h. This, hopefully, will make it more clear for
NIC driver implementors to know what functions to use for zero-copy
support.
v4->v5: Fix -Wmissing-prototypes by include header file. (Jakub)
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200520192103.355233-4-bjorn.topel@gmail.com
Intel drivers implement native AF_XDP zerocopy in separate C-files,
that have its own invocation of bpf_prog_run_xdp(). The setup of
xdp_buff is also handled in separately from normal code path.
This patch update XDP frame_sz for AF_XDP zerocopy drivers i40e, ice
and ixgbe, as the code changes needed are very similar. Introduce a
helper function xsk_umem_xdp_frame_sz() for calculating frame size.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Cc: Magnus Karlsson <magnus.karlsson@intel.com>
Link: https://lore.kernel.org/bpf/158945347511.97035.8536753731329475655.stgit@firesoul
This driver uses different memory models depending on PAGE_SIZE at
compile time. For PAGE_SIZE 4K it uses page splitting, meaning for
normal MTU frame size is 2048 bytes (and headroom 192 bytes). For
larger MTUs the driver still use page splitting, by allocating
order-1 pages (8192 bytes) for RX frames. For PAGE_SIZE larger than
4K, driver instead advance its rx_buffer->page_offset with the frame
size "truesize".
For XDP frame size calculations, this mean that in PAGE_SIZE larger
than 4K mode the frame_sz change on a per packet basis. For the page
split 4K PAGE_SIZE mode, xdp.frame_sz is more constant and can be
updated once outside the main NAPI loop.
The default setting in the driver uses build_skb(), which provides
the necessary headroom and tailroom for XDP-redirect in RX-frame
(in both modes).
There is one complication, which is legacy-rx mode (configurable via
ethtool priv-flags). There are zero headroom in this mode, which is a
requirement for XDP-redirect to work. The conversion to xdp_frame
(convert_to_xdp_frame) will detect this insufficient space, and
xdp_do_redirect() call will fail. This is deemed acceptable, as it
allows other XDP actions to still work in legacy-mode. In
legacy-mode + larger PAGE_SIZE due to lacking tailroom, we also
accept that xdp_adjust_tail shrink doesn't work.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: intel-wired-lan@lists.osuosl.org
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Alexander Duyck <alexander.duyck@gmail.com>
Link: https://lore.kernel.org/bpf/158945347002.97035.328088795813704587.stgit@firesoul
Fix to return a error code from the error handling case
instead of 0, as done elsewhere in this function.
Fixes: 31ad4e4ee1 ("ice: Allocate flow profile")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQJIBAABCgAyFiEEgMe7l+5h9hnxdsnuWYigwDrT+vwFAl6GTQMUHGJoZWxnYWFz
QGdvb2dsZS5jb20ACgkQWYigwDrT+vy3PhAAmqpYBRobOsG8QbmKDjoJEFtkqdvD
z6+4zf/R+hF11RyXjMDwihIe8d+tkQ4eAaYu6Oh5PrTyanz0G0PgeCrivZeytULk
thqQIWzDQMVA5vN/2/Vy8s5s+3HzP8z/MZOFScJ7+xA1MndXptPRTNmFUbjx+GAv
x8/pTp0u9AF6m7itX65DxXvwkzjWamt+Ar4Yx2IcuKAU/M5RtfuZO3PpDnqn7/wk
JFlkRoYeFB6qNnnkPdeyPHl9dALhuhzgdTyklQEnKVW3nf3xThYDhcEwdh6kBQgl
0dH8lL5LXy7PKGN8RES4wB0Vqndw/HlsCF5O4wkkfItbnbJxGJtS139e5973m0ud
sgWvF4yJAT2jCKhIeNz34sePQJMyWALhv0XzZCsJ0YeGHsrV1jrHELkwUT1+eIsT
3UV0iZ6aL06zQJDyKUbbIcQzEQ/wwBC+x9VgsyL54K1quCQZ1N1Nl/dvrb4cRG9m
m9EhJK/brDf4c0uFlOmMTSxV1t5J+z6ZSQnh1ShD/o5yBsxqN6q5brDT6LEs+jbM
LsIkA18jJOd4OyiDs98YiFKvIfFQbQ0LEBQpJwhF0snvfBFMMbUYN/T/NYneWON/
F0TpkFoP7PXDuq55iNaLdnObfzrpC9kdzUyWvePUvjxIl55bkf+/qtUny+H48t4L
dNggvW052d7BHes=
=deWu
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Revert sysfs "rescan" renames that broke apps (Kelsey Skunberg)
- Add more 32 GT/s link speed decoding and improve the implementation
(Yicong Yang)
Resource management:
- Add support for sizing programmable host bridge apertures and fix a
related alpha Nautilus regression (Ivan Kokshaysky)
Interrupts:
- Add boot interrupt quirk mechanism for Xeon chipsets and document
boot interrupts (Sean V Kelley)
PCIe native device hotplug:
- When possible, disable in-band presence detect and use PDS
(Alexandru Gagniuc)
- Add DMI table for devices that don't use in-band presence detection
but don't advertise that correctly (Stuart Hayes)
- Fix hang when powering slots up/down via sysfs (Lukas Wunner)
- Fix an MSI interrupt race (Stuart Hayes)
Virtualization:
- Add ACS quirks for Zhaoxin devices (Raymond Pang)
Error handling:
- Add Error Disconnect Recover (EDR) support so firmware can report
devices disconnected via DPC and we can try to recover (Kuppuswamy
Sathyanarayanan)
Peer-to-peer DMA:
- Add Intel Sky Lake-E Root Ports B, C, D to the whitelist (Andrew
Maier)
ASPM:
- Reduce severity of common clock config message (Chris Packham)
- Clear the correct bits when enabling L1 substates, so we don't go
to the wrong state (Yicong Yang)
Endpoint framework:
- Replace EPF linkup ops with notifier call chain and improve locking
(Kishon Vijay Abraham I)
- Fix concurrent memory allocation in OB address region (Kishon Vijay
Abraham I)
- Move PF function number assignment to EPC core to support multiple
function creation methods (Kishon Vijay Abraham I)
- Fix issue with clearing configfs "start" entry (Kunihiko Hayashi)
- Fix issue with endpoint MSI-X ignoring BAR Indicator and Table
Offset (Kishon Vijay Abraham I)
- Add support for testing DMA transfers (Kishon Vijay Abraham I)
- Add support for testing > 10 endpoint devices (Kishon Vijay Abraham I)
- Add support for tests to clear IRQ (Kishon Vijay Abraham I)
- Add common DT schema for endpoint controllers (Kishon Vijay Abraham I)
Amlogic Meson PCIe controller driver:
- Add DT bindings for AXG PCIe PHY, shared MIPI/PCIe analog PHY (Remi
Pommarel)
- Add Amlogic AXG PCIe PHY, AXG MIPI/PCIe analog PHY drivers (Remi
Pommarel)
Cadence PCIe controller driver:
- Add Root Complex/Endpoint DT schema for Cadence PCIe (Kishon Vijay
Abraham I)
Intel VMD host bridge driver:
- Add two VMD Device IDs that require bus restriction mode (Sushma
Kalakota)
Mobiveil PCIe controller driver:
- Refactor and modularize mobiveil driver (Hou Zhiqiang)
- Add support for Mobiveil GPEX Gen4 host (Hou Zhiqiang)
Microsoft Hyper-V host bridge driver:
- Add support for Hyper-V PCI protocol version 1.3 and
PCI_BUS_RELATIONS2 (Long Li)
- Refactor to prepare for virtual PCI on non-x86 architectures (Boqun
Feng)
- Fix memory leak in hv_pci_probe()'s error path (Dexuan Cui)
NVIDIA Tegra PCIe controller driver:
- Use pci_parse_request_of_pci_ranges() (Rob Herring)
- Add support for endpoint mode and related DT updates (Vidya Sagar)
- Reduce -EPROBE_DEFER error message log level (Thierry Reding)
Qualcomm PCIe controller driver:
- Restrict class fixup to specific Qualcomm devices (Bjorn Andersson)
Synopsys DesignWare PCIe controller driver:
- Refactor core initialization code for endpoint mode (Vidya Sagar)
- Fix endpoint MSI-X to use correct table address (Kishon Vijay
Abraham I)
TI DRA7xx PCIe controller driver:
- Fix MSI IRQ handling (Vignesh Raghavendra)
TI Keystone PCIe controller driver:
- Allow AM654 endpoint to raise MSI-X interrupt (Kishon Vijay Abraham I)
Miscellaneous:
- Quirk ASMedia XHCI USB to avoid "PME# from D0" defect (Kai-Heng
Feng)
- Use ioremap(), not phys_to_virt(), for platform ROM to fix video
ROM mapping with CONFIG_HIGHMEM (Mikel Rychliski)"
* tag 'pci-v5.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (96 commits)
misc: pci_endpoint_test: remove duplicate macro PCI_ENDPOINT_TEST_STATUS
PCI: tegra: Print -EPROBE_DEFER error message at debug level
misc: pci_endpoint_test: Use full pci-endpoint-test name in request_irq()
misc: pci_endpoint_test: Fix to support > 10 pci-endpoint-test devices
tools: PCI: Add 'e' to clear IRQ
misc: pci_endpoint_test: Add ioctl to clear IRQ
misc: pci_endpoint_test: Avoid using module parameter to determine irqtype
PCI: keystone: Allow AM654 PCIe Endpoint to raise MSI-X interrupt
PCI: dwc: Fix dw_pcie_ep_raise_msix_irq() to get correct MSI-X table address
PCI: endpoint: Fix ->set_msix() to take BIR and offset as arguments
misc: pci_endpoint_test: Add support to get DMA option from userspace
tools: PCI: Add 'd' command line option to support DMA
misc: pci_endpoint_test: Use streaming DMA APIs for buffer allocation
PCI: endpoint: functions/pci-epf-test: Print throughput information
PCI: endpoint: functions/pci-epf-test: Add DMA support to transfer data
PCI: pciehp: Fix MSI interrupt race
PCI: pciehp: Fix indefinite wait on sysfs requests
PCI: endpoint: Fix clearing start entry in configfs
PCI: tegra: Add support for PCIe endpoint mode in Tegra194
PCI: sysfs: Revert "rescan" file renames
...
The AER interfaces to clear error status registers were a confusing mess:
- pci_cleanup_aer_uncorrect_error_status() cleared non-fatal errors
from the Uncorrectable Error Status register.
- pci_aer_clear_fatal_status() cleared fatal errors from the
Uncorrectable Error Status register.
- pci_cleanup_aer_error_status_regs() cleared the Root Error Status
register (for Root Ports), the Uncorrectable Error Status register,
and the Correctable Error Status register.
Rename them to make them consistent:
From To
---------------------------------------- -------------------------------
pci_cleanup_aer_uncorrect_error_status() pci_aer_clear_nonfatal_status()
pci_aer_clear_fatal_status() pci_aer_clear_fatal_status()
pci_cleanup_aer_error_status_regs() pci_aer_clear_status()
Since pci_cleanup_aer_error_status_regs() (renamed to
pci_aer_clear_status()) is only used within drivers/pci/, move the
declaration from <linux/aer.h> to drivers/pci/pci.h.
[bhelgaas: commit log, add renames]
Link: https://lore.kernel.org/r/d1310a75dc3d28f7e8da4e99c45fbd3e60fe238e.1585000084.git.sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a devlink region for exposing the device's Non Volatime Memory flash
contents.
Support the recently added .snapshot operation, enabling userspace to
request a snapshot of the NVM contents via DEVLINK_CMD_REGION_NEW.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export a unique board identifier using "board.id" for devlink's
.info_get command.
Obtain this by reading the NVM for the PBA identification string.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The devlink .info_get callback allows the driver to report detailed
version information. The following devlink versions are reported with
this initial implementation:
"fw.mgmt" -> The version of the firmware that controls PHY, link, etc
"fw.mgmt.api" -> API version of interface exposed over the AdminQ
"fw.mgmt.build" -> Unique build id of the source for the management fw
"fw.undi" -> Version of the Option ROM containing the UEFI driver
"fw.psid.api" -> Version of the NVM image format.
"fw.bundle_id" -> Unique identifier for the combined flash image.
"fw.app.name" -> The name of the active DDP package.
"fw.app" -> The version of the active DDP package.
With this, devlink dev info can report at least as much information as
is reported by ETHTOOL_GDRVINFO.
Compare the output from ethtool vs from devlink:
$ ethtool -i ens785s0
driver: ice
version: 0.8.1-k
firmware-version: 0.80 0x80002ec0 1.2581.0
expansion-rom-version:
bus-info: 0000:3b:00.0
supports-statistics: yes
supports-test: yes
supports-eeprom-access: yes
supports-register-dump: yes
supports-priv-flags: yes
$ devlink dev info pci/0000:3b:00.0
pci/0000:3b:00.0:
driver ice
serial number 00-01-ab-ff-ff-ca-05-68
versions:
running:
fw.mgmt 2.1.7
fw.mgmt.api 1.5
fw.mgmt.build 0x305d955f
fw.undi 1.2581.0
fw.psid.api 0.80
fw.bundle_id 0x80002ec0
fw.app.name ICE OS Default Package
fw.app 1.3.1.0
More pieces of information can be displayed, each version is kept
separate instead of munged together, and each version has an identifier
which comes with associated documentation.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Begin implementing support for the devlink interface with the ice
driver.
The pf structure is currently memory managed through devres, via
a devm_alloc. To mimic this behavior, after allocating the devlink
pointer, use devm_add_action to add a teardown action for releasing the
devlink memory on exit.
The ice hardware is a multi-function PCIe device. Thus, each physical
function will get its own devlink instance. This means that each
function will be treated independently, with its own parameters and
configuration. This is done because the ice driver loads a separate
instance for each function.
Due to this, the implementation does not enable devlink to manage
device-wide resources or configuration, as each physical function will
be treated independently. This is done for simplicity, as managing
a devlink instance across multiple driver instances would significantly
increase the complexity for minimal gain.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current implementation of .get_eeprom only enables reading from the
Shadow RAM portion of the NVM contents. Implement support for reading
the entire flash contents instead of only the initial portion contained
in the Shadow RAM.
A complete dump can take several seconds, but the ETHTOOL_GEEPROM ioctl
is capable of reading only a limited portion at a time by specifying the
offset and length to read.
In order to perform the reads directly, several functions are made non
static. Additionally, the unused ice_read_sr_buf_aq and ice_read_sr_buf
functions are removed.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When reading from the NVM using a flat address, it is useful to know the
upper bound on the size of the flash contents. This value is not stored
within the NVM.
We can determine the size by performing a bisection between upper and
lower bounds. It is known that the size cannot exceed 16 MB (offset of
0xFFFFFF).
Use a while loop to bisect the upper and lower bounds by reading one
byte at a time. On a failed read, lower the maximum bound. On
a successful read, increase the lower bound.
Save this as the flash_size in the ice_nvm_info structure that contains
data related to the NVM.
The size will be used in a future patch for implementing full NVM read
via ethtool's GEEPROM command.
The maximum possible size for the flash is bounded by the size limit for
the NVM AdminQ commands. Add a new macro, ICE_AQC_NVM_MAX_OFFSET, which
can be used to represent this upper bound.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The NVM version and Option ROM version information is stored within the
struct ice_nvm_ver_info structure. The data for the NVM is stored as
a 2byte value with the major and minor versions each using one byte from
the field. The Option ROM is stored as a 4byte value that contains
a major, build, and patch number.
Modify the code to immediately extract the version values and store them
in a new struct ice_orom_info. Remove the now unnecessary
ice_get_nvm_version function.
Update ice_ethtool.c to use the new fields directly from the structured
data.
This reduces complexity of the code that prints these versions in
ice_ethtool.c
Update the macro definitions and variable names to use the term "orom"
instead of "oem" for the Option ROM version. This helps increase the
clarity of the Option ROM version code.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The NVM contents are read via firmware by using the ice_aq_read_nvm
function. This function has a couple of limits:
1) The AdminQ commands can only take buffers sized up to 4Kb. Thus, any
larger read must be split into multiple reads.
2) when reading from the Shadow RAM, reads must not cross sector
boundaries. The sectors are also 4Kb in size.
Implement the ice_read_flat_nvm function to read portions of the NVM by
flat offset. That is, to read using offsets from the start of the NVM
rather than from a specific module.
This function will be able to read both from the NVM and from the Shadow
RAM. For simplicity NVM reads will always be broken up to not cross 4Kb
page boundaries, even though this is not required unless reading from
the Shadow RAM.
Use this new function as the implementation of ice_read_sr_word_aq.
The ice_read_sr_buf_aq function is not modified here. This is because
a following change will remove the only caller of that function in favor
of directly using ice_read_flat_nvm. Thus, there is little benefit to
changing it now only to remove it momentarily. At the same time, the
ice_read_sr_aq function will also be removed.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ice_read_sr_aq function returns words in the Little Endian format.
Remove the need for __force and typecasting by using a local variable in
the ice_read_sr_word_aq function.
Additionally clarify explicitly that the ice_read_sr_aq function takes
storage for __le16 values instead of using u16.
Being explicit about the endianness of this data helps when using tools
like sparse to catch endian-related issues.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function comment for ice_get_nvm_version indicated that the ver_hi
and ver_lo values were 16 bits. In fact, they are only uint8_t values,
meaning that they have a maximum size of 8 bits. Fix the comment to
match the correct size.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The variable name 'type' is not very descriptive. Replace instances of
those with a variable name that is more descriptive or replace it if not
needed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Using ENOTSUPP almost always results in some bizarre error message to
be printed in userspace. This is likely because ENOTSUPP was defined for
the NFS protocol (as per a comment in include/linux/errno.h). Use
EOPNOTSUPP instead.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit ed5a3f664c ("ice: Removing hung_queue variable to use txqueue
function parameter") began utilizing the txqueue variable over the
hung_queue variable. hung_queue was an int where txqueue is an unsigned
int. Update the format specifiers to reflect the new type.
Fixes: ed5a3f664c ("ice: Removing hung_queue variable to use txqueue function parameter")
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
checkpatch complains "CHECK:DEPRECATED_API: Deprecated use of 'strlcpy',
prefer 'stracpy or strscpy' instead"; use strscpy.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the PF's mailbox receive queue is only 512 entries. This fine,
but considering that all VF's mailbox send queues funnel into the PF's
single mailbox receive queue, let's increase it to the maximum size. This
will help prevent any possible bottleneck/slowdown occurring from the PF's
mailbox receive queue being full.
Signed-off-by: Lukasz Czapnik <lukasz.czapnik@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
VLAN pruning is not always being set correctly due to a previous change
that set Tx antispoof off. ice_vsi_is_vlan_pruning_ena() currently checks
for both Tx antispoof and Rx pruning. The expectation for this function is
to only check Rx pruning so fix the check.
Fixes: cd6d6b8331 ("ice: Fix VF spoofchk")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When switching from SW DCB to FW DCB it is necessary
to renegotiate DCBx so that the FW agent can have up
to date information about the DCB settings of the link
partner.
Perform an autoneg restart on the link when activating
FW DCB.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
While testing DCB for a corner case in which mode is switched from IEEE to
CEE and pfc_ena bitmask unchanged then DCBX mode doesn't get updated.
This is happening because the function ice_dcb_get_mode() is called
in a "no change detected block" instead of "change detected block".
Signed-off-by: Avinash JD <avinash.dayanand@intel.com>
Signed-off-by: Scott Register <scottx.register@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the "Link detected" field is not shown when the device goes
into safe mode. This is because the safe mode Ethtool ops does not set the
get_link function. Fix this by setting the safe mode Ethtool op get_link
function.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, if there are bare-metal VFs passing traffic and the ice
driver is removed, there is a possibility of VFs triggering a Tx timeout
right before iavf_remove(). This is causing iavf_close() to not be
called because there is a check in the beginning of iavf_remove() that
bails out early if (adapter->state < IAVF_DOWN_PENDING). This makes it
so some resources do not get cleaned up. Specifically, free_irq()
is never called for data interrupts, which results in the following line
of code to trigger:
pci_disable_msix()
free_msi_irqs()
...
BUG_ON(irq_has_action(entry->irq + i));
...
To prevent the Tx timeout from occurring on the VF during driver unload
for ice and the iavf there are a few changes that are needed.
[1] Don't disable all active VF Tx/Rx queues prior to calling
pci_disable_sriov.
[2] Call ice_free_vfs() before disabling the service task.
[3] Disable VF resets when the ice driver is being unloaded by setting
the pf->state flag __ICE_VF_RESETS_DISABLED.
Changing [1] and [2] allow each VF driver's remove flow to successfully
send VIRTCHNL requests, which includes queue disable. This prevents
unexpected Tx timeouts because the PF driver is no longer forcefully
disabling queues.
Due to [1] and [2] there is a possibility that the PF driver will get a
VFLR or reset request over VIRTCHNL from a VF during PF driver unload.
Prevent that by doing [3].
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently when the device runs out of MSI-X interrupts a cryptic and
unhelpful message is printed. This will cause confusion when hitting this
case. Fix this by clearing up the error message for both SR-IOV and non
SR-IOV use cases.
Also, make a few minor changes to increase clarity of variables.
1. Change per VF MSI-X and queue pair variables in the PF structure.
2. Use ICE_NONQ_VECS_VF when determining pf->num_msix_per_vf instead of
the magic number "1". This vector is reserved for the OICR.
All of the resource tracking functions were moved to avoid adding
any forward declaration function prototypes.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Unlike the XL710 series, 800-series hardware can allocate more than 4
MSI-X vectors per VF. This patch enables that functionality. We
dynamically allocate vectors and queues depending on how many VFs are
enabled. Allocating the maximum number of VFs replicates XL710
behavior with 4 queues and 4 vectors. But allocating a smaller number
of VFs will give you 16 queues and 16 vectors.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sergei Shtylyov pointed out that two instances of parenthesis are not
needed, so remove them.
Suggested-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Replace the open-coded implementation for reading the PCIe DSN with
pci_get_dsn().
The pci_get_dsn() function will perform two pci_read_config_dword calls
to read the lower and upper config dwords. It bitwise ORs them into
a u64 value. Instead of using put_unaligned_le32 to convert the value to
LE32 format, just use the %016llX printf specifier. This will print the
u64 correct, putting the most significant byte of the value first. Since
pci_get_dsn() correctly orders the two dwords into a u64, this should
produce equivalent results in less code.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver correctly rejects all unsupported parameters.
As a side effect of these changes the info message about
the bad parameter will no longer be printed. We also
always reject the tx_coalesce_usecs_high param, even
if the target queue pair does not have a TX queue.
Error code changes from EINVAL to EOPNOTSUPP.
v2: allow adaptive TX
v3: adjust commit message for new error code and member name
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This product's name has changed; update the macro identifier accordingly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add E823 device ids and convert conditional expressions to a more
appropriate switch statement.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for device id 0x159b.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There were several strings found without line feeds, fix
them by adding a line feed, as is typical. Without this
lotsofmessagescanbejumbledtogether.
This patch has known checkpatch warnings from long lines
for the NL_* messages, because checkpatch doesn't know
how to ignore them.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Increase the maximum time that the driver will wait for a PF reset from
200 milliseconds to 300 milliseconds, to account for possibility of
a slightly longer than expected PF reset.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for a new AF_XDP feature that has already been introduced in
upstreamed Intel NIC drivers. If a user space application signals that
it might sleep using the new bind flag XDP_USE_NEED_WAKEUP, the driver
will then set this flag if it has no more buffers on the NIC Rx ring and
yield to the application. For Tx, it will set the flag if it has no
outstanding Tx completion interrupts and return to the application.
Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
lldpad is using the value reported in the DCB config for
max_tc as the max allowed number of TCs, not the current
max. ICE driver was reporting it as current maximum TC.
Change DCB_NL function to report maximum TC allowed by
this device.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add code to detect if DCB is in IEEE or CEE mode. Without this the code
will always report as IEEE mode which is incorrect and confuses the
user.
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Signed-off-by: Scott Register <scottx.register@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Couple of DCBNL ops are required for configuring ETS in SW DCB CEE mode. If
these functions are not added, it'll break the CEE functionality.
Signed-off-by: Avinash JD <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently when the PF reduces its number of channels via ethtool and
then VFs are created there may be stale data for some of the Rx queues
belonging to VFs. This happens when a VF reuses an Rx queue that was
previously used by the PF. Specifically, the QRXFLXP_CNTXT register
will have incorrect values. Fix this by always clearing the relevant
values in the QRXFLXP_CNTXT register for VF queues.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Order intermediate VSIG list correct in order to correctly match existing
VSIG lists.
When overriding pre-existing TCAM entries, properly delete the existing
entry and remove it from the change/update list.
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update the PF VFs MDD event message to rate limit once per second and
report the total number Rx|Tx event count. Add support to print pending
MDD events that occur during the rate limit. The use of net_ratelimit did
not allow for per VF Rx|Tx granularity.
Additional PF MDD log messages are guarded by netif_msg_[rx|tx]_err().
Since VF RX MDD events disable the queue, add ethtool private flag
mdd-auto-reset-vf to configure VF reset to re-enable the queue.
Disable anti-spoof detection interrupt to prevent spurious events
during a function reset.
To avoid race condition do not make PF MDD register reads conditional
on global MDD result.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Validate the inputs for SW DCB config received either via lldptool or pcap
file. And don't apply DCB for bad bandwidth inputs. Without this patch, any
config having bad inputs will cause the loss of link making PF unusable
even after driver reload. Recoverable only via system reboot.
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The configuration/command below is failing when the VF in the xml
file is already bound to the host iavf driver.
pci_0000_af_0_0.xml:
<interface type='hostdev' managed='yes'>
<source>
<address type='pci' domain='0x0000' bus='0xaf' slot='0x0' function='0x0'/>
</source>
<mac address='00🇩🇪ad:00:11:01'/>
</interface>
> virsh attach-device domain_name pci_0000_af_0_0.xml
error: Failed to attach device from pci_0000_af_0_0.xml
error: Cannot set interface MAC/vlanid to 00🇩🇪ad:00:11:01/0 for
ifname ens1f1 vf 0: Device or resource busy
This is failing because the VF has not been completely removed/reset
after being unbound (via the virsh command above) from the host iavf
driver and ice_set_vf_mac() checks if the VF is disabled before waiting
for the reset to finish.
Fix this by waiting for the VF remove/reset process to happen before
checking if the VF is disabled. Also, since many functions for VF
administration on the PF were more or less calling the same 3 functions
(ice_wait_on_vf_reset(), ice_is_vf_disabled(), and ice_check_vf_init())
move these into the helper function ice_check_vf_ready_for_cfg(). Then
call this function in any flow that attempts to configure/query a VF
from the PF.
Lastly, increase the maximum wait time in ice_wait_on_vf_reset() to
800ms, and modify/add the #define(s) that determine the wait time.
This was done for robustness because in rare/stress cases VF removal can
take a max of ~800ms and previously the wait was a max of ~300ms.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove code that tell the OS that link is going down when user
change flow control via ethtool. When link is up it isn't certain
that link goes down after 0x0605 aq command. If link doesn't go
down, OS thinks that link is down, but physical link is up. To
reset this state user have to take interface down and up.
If link goes down after 0x0605 command, FW send information
about that and after that driver tells the OS that the link goes
down. So this code in ethtool is unnecessary.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently if a user sets an odd [tx|rx]-usecs value through ethtool,
the request is denied because the hardware is set to have an ITR
granularity of 2us. This caused poor customer experience. Fix this by
aligning to a register allowed value, which results in rounding down.
Also, print a once per ring container type message to be clear about
our intentions.
Also, change the ITR_TO_REG define to be the bitwise and of the ITR
setting and the ICE_ITR_MASK. This makes the purpose of ITR_TO_REG more
obvious.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Subject says it all.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit 0290bd291c ("netdev: pass the stuck queue to the timeout handler")
introduced a new argument to the function but missed adding the description
of the argument to the function header comment. Add it now.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Compiling with gcc-9.2.1 with W=1 points out warnings about the improper
function parameter list. Fix it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
"fallthrough" comments are used in switch case statements to explicitly
indicate the code is intended to fall through to the following statement.
Different variants of "fallthough" are acceptable, e.g. "fall through",
"fallthrough", "Fall-through". The GCC compiler has an optional warning
(-Wimplicit-fallthrough[=n]) to warn when such a comment is not present;
the default version of which is enabled when compiling the Linux kernel.
There have been recent discussions in kernel mailing lists regarding
replacing non-standardized "fallthrough" comments with the pseudo-reserved
word 'fallthrough' which will be defined as __attribute__ ((fallthrough))
for versions of gcc that support it (i.e. gcc 7 and newer) or as a nop
for versions that do not. Replace "fallthrough" comments with fallthrough
reserved word.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fallthrough comments are used to explicitly indicate the code is intended
to flow from one case statement to the next in a switch statement rather
than break out of the switch statement. They are only needed when a case
has one or more statements to execute before falling through to the next
case, not when there is a list of cases for which the same statement(s)
should be executed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently in ice_vc_ena_qs_msg() we are incorrectly validating the
virtchnl queue select bitmaps. The virtchnl_queue_select rx_queues and
tx_queue bitmap is being compared against ICE_MAX_BASE_QS_PER_VF, but
the problem is that these bitmaps can have a value greater than
ICE_MAX_BASE_QS_PER_VF. Fix this by comparing the bitmaps against
BIT(ICE_MAX_BASE_QS_PER_VF).
Also, add the function ice_vc_validate_vqs_bitmaps() that checks to see
if both virtchnl_queue_select bitmaps are empty along with checking that
the bitmaps only have valid bits set. This function can then be used in
both the queue enable and disable flows.
Arkady Gilinksky's patch on the intel-wired-lan mailing list
("i40e/iavf: Fix msg interface between VF and PF") made me
aware of this issue.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently when a VF driver sends the PF a request to disable Rx queues
we will disable them one at a time, even if the VF driver sent us a
batch of queues to disable. This is causing issues where the Rx queue
disable times out with LFC enabled. This can be improved by detecting
when the VF is trying to disable all of its queues.
Also remove the variable num_qs_ena from the ice_vf structure as it was
only used to see if there were no Rx and no Tx queues active. Instead
add a function that checks if both the vf->rxq_ena and vf->txq_ena
bitmaps are empty.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently we are not handling LAN overflow events. There can be cases
where LAN overflow events occur on VF queues, especially with Link Flow
Control (LFC) enabled on the controlling PF. In order to recover from
the LAN overflow event caused by a VF we need to determine if the queue
belongs to a VF and reset that VF accordingly.
The struct ice_aqc_event_lan_overflow returns a copy of the GLDCB_RTCTQ
register, which tells us what the queue index is in the global/device
space. The global queue index needs to first be converted to a PF space
queue index and then it can be used to find if a VF owns it.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently in ice_vsi_get_qs() we set the mapping_mode for Tx and Rx to
vsi->[tx|rx]_mapping_mode, but the problem is vsi->[tx|rx]_mapping_mode
have not been set yet. This was working because ICE_VSI_MAP_CONTIG is
defined to 0. Fix this by being explicit with our mapping mode by
initializing the Tx and Rx structure's mapping_mode to
ICE_VSI_MAP_CONTIG and then setting the vsi->[tx|rx]_mapping_mode to the
[tx|rx]_qs_cfg.mapping_mode values.
Also, only assign the vsi->[tx|rx]_mapping_mode when the queues are
successfully mapped to the VSI. With this change there was no longer a
need to initialize the ret variable to 0 so remove that.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently when we enable/disable all Rx queues we do the following
sequence for each Rx queue and then move to the next queue.
1. Enable/Disable the Rx queue via register write.
2. Read the configuration register to determine if the Rx queue was
enabled/disabled successfully.
In some cases enabling/disabling queue 0 fails because of step 2 above.
Fix this by doing step 1 for all of the Rx queues and then step 2 for
all of the Rx queues.
Also, there are cases where we enable/disable a single queue (i.e.
SR-IOV and XDP) so add a new function that does step 1 and 2 above with
a read flush in between.
This change also required a single Rx queue to be enabled/disabled with
and without waiting for the change to propagate through hardware. Fix
this by adding a boolean wait flag to the necessary functions.
Also, add the keywords "one" and "all" to distinguish between
enabling/disabling a single Rx queue and all Rx queues respectively.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the VF can see other's broadcast and multicast traffic because
it always has a VLAN filter for VLAN 0. Fix this by removing/adding the
VF's VLAN 0 filter when a port VLAN is added/removed respectively.
This required a few changes.
1. Move where we add VLAN 0 by default for the VF into
ice_alloc_vsi_res() because this is when we determine if a port VLAN is
present for load and reset.
2. Moved where we kill the old port VLAN filter in
ice_set_vf_port_vlan() to the very end of the function because it allows
us to save the old port VLAN configuration upon any failure case.
3. During adding/removing of a port VLAN via ice_set_vf_port_vlan() we
also need to remove/add the VLAN 0 filter rule respectively.
4. Improve log messages.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently when configuring a port VLAN for a VF we are only shifting the
QoS bits by 12. This is incorrect. Fix this by getting rid of the ICE
specific VLAN defines and use the kernel VLAN defines instead.
Also, don't assign a value to vlanprio until the VLAN ID and QoS
parameters have been validated.
Also, there are many places we do (le16_to_cpu(vsi->info.pvid) &
VLAN_VID_MASK). Instead do (vf->port_vlan_info & VLAN_VID_MASK) because
we always save what's stored in vsi->info.pvid to vf->port_vlan_info in
the CPU's endianness.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The check for vf->link_up is incorrect because this field is only valid if
vf->link_forced is true. Fix this by adding the helper ice_is_vf_link_up()
to determine if the VF's link is up.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently ice_vsi_manage_pvid() calls
ice_vsi_[set|kill]_pvid_fill_ctxt() when enabling/disabling a port VLAN
on a VSI respectively. These two functions have some duplication so just
move their unique pieces inline in ice_vsi_manage_pvid() and then the
duplicate code can be reused for both the enabling/disabling paths.
Before this patch the info.pvid field was not being written
correctly via ice_vsi_kill_pvid_fill_ctxt() so it was being hard coded
to 0 in ice_set_vf_port_vlan(). Fix this by setting the info.pvid field
to 0 before calling ice_vsi_update() in ice_vsi_manage_pvid().
We currently use vf->port_vlan_id to keep track of the port VLAN
ID and QoS, which is a bit misleading. Fix this by renaming it to
vf->port_vlan_info. Also change the name of the argument for
ice_vsi_manage_pvid() from vid to pvid_info.
In ice_vsi_manage_pvid() only save the fields that were modified
in the VSI properties structure on success instead of the entire thing.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allow support for S-Tag + C-Tag VLAN traffic by disabling pruning when
there are no 0x8100 VLAN interfaces currently created on top of the PF.
When an 0x8100 VLAN interface is configured, enable pruning and only
support single and double C-Tag VLAN traffic. If all of the 0x8100
interfaces that were created on top of the PF are removed via
ethtool -K <iface> rx-vlan-filter off or via ip tools, then disable
pruning and allow S-Tag + C-Tag traffic again.
Add VLAN 0 filter by default for the PF. This is because a bridge
sets the default_pvid to 1, sends the request down to
ice_vlan_rx_add_vid(), and we never get the request to add VLAN 0 via
the 8021q module which causes all untagged traffic to be dropped.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a collection of trivial fixes including fixing whitespace, typos,
function headers, reverse Christmas tree, etc.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the correct netif_msg_[tx,rx]_error() function to determine whether to
print the MDD event type.
Signed-off-by: Ben Shelton <benjamin.h.shelton@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1. Remove local variable num_q_vectors and use vsi->num_q_vectors instead
2. Remove local variable pf and pass vsi->back to ice_pf_to_dev
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Formatting strings in print function calls (like dev_info, dev_err, etc.)
can exceed 80 columns without making checkpatch unhappy. So remove
newlines where applicable and make print statements more compact.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use ice_pf_to_dev(pf) instead of &pf->pdev->dev
Use ice_pf_to_dev(vsi->back) instead of &vsi->back->pdev->dev
When a pointer to the pf instance is available, use ice_pf_to_dev
instead of ice_hw_to_dev
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit 1f45ebe0d8 ("ice: add extra check for null Rx descriptor") moved
the call to ice_construct_skb() under a null check as Coverity reported a
possible use of null skb. However, the original call was not deleted, do so
now.
Fixes: 1f45ebe0d8 ("ice: add extra check for null Rx descriptor")
Reported-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After a reset the Unit Load Status bits in the GLNVM_ULD register to check
for completion should be 0x7FF before continuing. Update the mask to check
(minus the three reserved bits that are always set).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Logging the firmware/NVM information during driver load is redundant since
that information is also available via ethtool. Move the functionality
found in ice_nvm_version_str() directly into ice_get_drvinfo() and remove
calling the former and logging that info during driver probe. This also
gets rid of a bug in ice_nvm_version_str() where it returns a pointer to
a buffer which is free'ed when that function exits.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch modifies link message logging to include "Full Duplex" and
"Negotiated" for FEC, so as to distinguish it from "Requested" FEC.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove unnecessary CONFIG_PCI_IOV wrapping in ice_set_pf_caps. None
of the data structures accessed within the block are wrapped with
this flag. When CONFIG_PCI_IOV is undefined, pf->num_vfs_supported
will be 0 anyway.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_dev_onetime_setup contains driver workarounds needed for
firmware limitations. These issues have now been resolved in newer
NVMs so remove the function.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently we compare the value we are about to write to the Rx tail
register with the previous value of next_to_use. The problem with this
is we only write tail on 8 descriptor boundaries, but next_to_use is
updated whenever we clean Rx descriptors. Fix this by comparing the
value we are about to write to tail with the previously written tail
value. This will prevent duplicate Rx tail bumps.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Display all of the supported and advertised link modes based on the PHY
capability with media.
Displaying all supported modes is more informative then only displaying
the current link mode.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When switching between FW and SW LLDP mode, the
number of configured TLV apps in the driver's
DCB configuration is getting out of synch with
what lldpad thinks is configured. This is causing
a problem when shutting down lldpad. The cleanup
is trying to delete TLV apps that are not defined
in the kernel.
Since the driver is keeping an accurate account
of the apps defined, use the drivers number of
apps to determine if there is an app to delete.
If the number of apps is <= 1, then do not
attempt to delete.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function ice_dcb_rebuild had some logic
flaws in it, and also didn't differentiate
between FW and SW modes needs.
For FW flow, the willing setting was being
forced to OFF and left that way. Unwilling
in DCB FW mode is not a supported model.
Leave the config alone and use the return value
from the set command to determine if setting the
config was successful.
The SW DCB flow does not need to need to register
for MIB change events (as they are not used in
SW mode).
Use !is_sw_lldp checks to only perform FW specific
task while in FW mode.
Also adding a reapplication of the current DCB
config after a link event. Some NVMs are not
maintaining their DCB configs across link events.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump version to 0.8.2-k
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Provide support to change or retrieve RSS hash options for a flow type.
The supported flow-types are: tcp4, tcp6, udp4, udp6, sctp4, sctp6.
Signed-off-by: Md Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set configuration for hardware RSS tables for VFs.
Signed-off-by: Md Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Attempt to optimize TCAM entries and reduce table resource usage by
searching for profiles that can be reused. Provide resource cleanup
of both hardware and software structures.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Write the hardware tables based on the populated software structures.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
