The driver needs to inform the hardware about the first invalid (not yet
filled) rx slot, by writing its DMA descriptor pointer offset to the
BGMAC_DMA_RX_INDEX register.
This register was set to a value exceeding the rx ring size, effectively
allowing the hardware constant access to the full ring, regardless of
which slots are initialized.
To fix this issue, always mark the last filled rx slot as invalid.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of allocating buffers at device init time and initializing
descriptors at device open, do both at the same time (during open).
Free all buffers when closing the device.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Limiting it to 511 looks like a failed attempt at leaving one descriptor
empty to allow the hardware to stop processing a buffer that has not
been prepared yet. However, this doesn't work because this affects the
total ring size as well
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In very rare cases, the MAC can catch an internal buffer that is bigger
than it's supposed to be. Instead of crashing the kernel, simply pass
the buffer back to the hardware
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate a new buffer before processing the completed one. If allocation
fails, reuse the old buffer.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A packet buffer offset of 30 bytes is inefficient, because the first 2
bytes end up in a different cacheline.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always poll rx and tx during NAPI poll instead of relying on the status
of the first interrupt. This prevents bgmac_poll from leaving unfinished
work around until the next IRQ.
In my tests this makes bridging/routing throughput under heavy load more
stable and ensures that no new IRQs arrive as long as bgmac_poll uses up
the entire budget.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep incrementing ring->start and ring->end instead of pointing it to
the actual ring slot entry. This simplifies the calculation of the
number of free slots.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull trivial tree from Jiri Kosina:
"Usual trivial tree updates. Nothing outstanding -- mostly printk()
and comment fixes and unused identifier removals"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
goldfish: goldfish_tty_probe() is not using 'i' any more
powerpc: Fix comment in smu.h
qla2xxx: Fix printks in ql_log message
lib: correct link to the original source for div64_u64
si2168, tda10071, m88ds3103: Fix firmware wording
usb: storage: Fix printk in isd200_log_config()
qla2xxx: Fix printk in qla25xx_setup_mode
init/main: fix reset_device comment
ipwireless: missing assignment
goldfish: remove unreachable line of code
coredump: Fix do_coredump() comment
stacktrace.h: remove duplicate declaration task_struct
smpboot.h: Remove unused function prototype
treewide: Fix typo in printk messages
treewide: Fix typo in printk messages
mod_devicetable: fix comment for match_flags
Conflicts:
drivers/net/usb/asix_common.c
drivers/net/usb/sr9800.c
drivers/net/usb/usbnet.c
include/linux/usb/usbnet.h
net/ipv4/tcp_ipv4.c
net/ipv6/tcp_ipv6.c
The TCP conflicts were overlapping changes. In 'net' we added a
READ_ONCE() to the socket cached RX route read, whilst in 'net-next'
Eric Dumazet touched the surrounding code dealing with how mini
sockets are handled.
With USB, it's a case of the same bug fix first going into net-next
and then I cherry picked it back into net.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, MoCA fixed PHYs are always in link-up state, regardless of
whether the link is actually up or not.
Add code to properly detect MoCA link state changes and to reflect the
new state in MoCA fixed PHY. Only GENET V3 and V4 MACs are capable of
detecting MoCA link state changes.
The code works as follows:
1. GENET MAC detects MoCA link state change and issues UMAC_IRQ_LINK_UP
or UMAC_IRQ_LINK_DOWN interrupt.
2. Link up/down interrupt is processed in bcmgenet_irq_task(), which
calls phy_mac_interrupt().
3. phy_mac_interrupt() updates the fixed PHY phydev->link and kicks
the PHY state machine.
4. PHY state machine proceeds to read the fixed PHY link status
register.
5. When the fixed PHY link status register is being read, the new
function bcmgenet_fixed_phy_link_update() gets called. It copies
the fixed PHY phydev->link value to the fixed PHY status->link.
6. PHY state machine receives the new link state of the fixed PHY.
7. MoCA fixed PHY link state now correctly reflects the real MoCA
hardware link state.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When IOMM-vtd is active, once main kernel crashes unfinished DMAE transactions
will be blocked, putting the HW in an error state which will cause further
transactions to timeout.
Current employed logic uses wrong macros, causing the first function to be the
only function that cleanups that error state during its probe/load.
This patch allows all the functions to successfully re-load in kdump kernel.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running in a kdump kernel, it's very likely that due to sync. loss with
management firmware the first PCI function to probe and reach the previous
unload flow would decide it can reset the chip and continue onward. While doing
so, it will only close its own Rx port.
On a 4-port device where 2nd port on engine is a 1g-port, the 2nd port would
allow ingress traffic after the chip is reset [assuming it was active on the
first kernel]. This would later cause a HW attention.
This changes driver flow to close both ports' 1g capabilities during the
previous driver unload flow prior to the chip reset.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two reasons for having this header in the common place:
1) Simplifying drivers that read NVRAM entries. We will be able to
safely call bcm47xx_nvram_* functions without #ifdef-s.
2) Getting NVRAM driver out of MIPS arch code. This is needed to support
BCM5301X arch which also requires this NVRAM driver. Patch for that
will follow once we get is reviewed.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: linux-soc@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8619/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch changes the driver to use ns_to_timespec64() instead of
open coding the same logic.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the driver to use ns_to_timespec64() and
timespec64_to_ns() instead of open coding the same logic.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On phy_mac_interrupt() call, the new_link parameter should be 0 or 1.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add #define UMAC_IRQ_LINK_EVENT to simplify link event handling code.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If bcmgenet_init_dma() fails, it cleans up after itself. Rx and Tx
DMAs are off, and NAPI instances haven't been netif_napi_add()'ed.
Therefore, we need to skip calling bcmgenet_fini_dma() on the error
handling path. bcmgenet_resume() already does this correctly.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcmgenet_fini_dma() is the only caller of __bcmgenet_fini_dma().
Move __bcmgenet_fini_dma() code inside bcmgenet_fini_dma().
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add #define for UMAC_IRQ_RXDMA_DONE and UMAC_IRQ_TXDMA_DONE in order
to simplify the code that handles Rx and Tx default queue interrupts.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use bool constants as the return values instead of 1 and 0.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's possible that due to errors [either on PCI or on device itself]
registers reads would fail, returning all-Fs.
This adds a check as early as possible so that driver will not read junk
values and make incorrect probe decisions according to them; instead,
gracefully fail the probe.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Number of link changes are now being stored in shared memory [by all possible
link owners], for management use [as well as possible debug information for
dumps].
Signed-off-by: Yaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable controlling Post2, coeff, IPreDriver and IFir according to NVRAM setup.
Signed-off-by: Yaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device appears to use a 64 bit nanoseconds register, and so with
this patch the driver should be ready for the year 2038.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver's clock is implemented using a timecounter, and so with
this patch the driver is ready for the year 2038.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To allow drivers to handle the features check for multiple tags,
move the check to ndo_features_check().
As no drivers currently handle multiple tagged TSO, introduce
dflt_features_check() and call it if the driver does not have
ndo_features_check().
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for multiple Rx queues:
1. Add NAPI context per Rx queue
2. Modify Rx interrupt and Rx NAPI code to handle multiple Rx queues
Signed-off-by: Petri Gynther <pgynther@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new bcmgenet functions to handle the NAPI calls to:
netif_napi_add()
napi_enable()
napi_disable()
netif_napi_del()
Signed-off-by: Petri Gynther <pgynther@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new bcmgenet functions to handle the NAPI calls to:
netif_napi_add()
napi_enable()
napi_disable()
netif_napi_del()
Signed-off-by: Petri Gynther <pgynther@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use more meaningful variable names int0_enable and int1_enable when
enabling bcmgenet interrupts.
For Rx default queue interrupts, use:
UMAC_IRQ_RXDMA_BDONE | UMAC_IRQ_RXDMA_PDONE
For Tx default queue interrupts, use:
UMAC_IRQ_TXDMA_BDONE | UMAC_IRQ_TXDMA_PDONE
Signed-off-by: Petri Gynther <pgynther@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do the two kcalloc() calls first, before proceeding into Rx/Tx DMA init.
Makes the error case handling much simpler.
Signed-off-by: Petri Gynther <pgynther@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Jaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary function parameter priv. Use ring->priv instead.
Signed-off-by: Petri Gynther <pgynther@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused priv->int0_mask and priv->int1_mask.
Signed-off-by: Petri Gynther <pgynther@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Statistics' state-machine in bnx2x driver must be synced with various driver
flows, but its current locking scheme manages to be wasteful [using 2 locks +
additional local variable] and prone to race-conditions at the same time,
as the state-machine and 'action' are being accessed under different locks.
In addition, current 'safe exec' isn't in fact safe, since the only guarantee
it gives is that DMA transactions are over, but ramrods might still be running.
This patch cleans up said logic, leaving us with a single lock for the entire
flow and removing the possible races.
Changes from v2:
- Switched into mutex locking from semaphore locking.
- Release locks on error flows.
Changes from v1:
Failure to acquire lock fails flow instead of printing a warning and
allowing access to the critical section.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the interface is not used, power down the integrated GPHY during
suspend. Similarly to bcmgenet_open(), bcmgenet_resume() powers on the GPHY
prior to any UniMAC activity.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Power up the GPHY while we are bringing-up the network interface, and
conversely, upon bring down, power the GPHY down. In order to avoid
creating hardware hazards, make sure that the GPHY gets powered on
during bcmgenet_open() prior to the UniMAC being reset as the UniMAC may
start creating activity towards the GPHY if we reverse the steps.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the GPHY power down sequence by setting all power down bits, putting
the GPHY in reset, and finally cutting the 25Mhz reference clock.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were missing a number of extra steps and delays to power-up the GPHY, update
the sequence to reflect the proper procedure here.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for implementing the power down GPHY sequence, rename
bcmgenet_ephy_power_up to illustrate that it is not EPHY specific but
PHY agnostic, and add an "enable" argument.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CK25_DIS bit controls whether a 25Mhz clock is fed to the GPHY or
not, in preparation for powering down the integrated GPHY when relevant,
make sure we clear that bit.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If bcmgenet_power_down() fails, we would want to propagate a return
value from bcmgenet_wol_power_down_cfg() to know about this.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always use software checksumming, since the hardware does not have any
checksum offload support.
This significantly improves local TCP tx performance.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The start-of-frame and end-of-frame bits were accidentally swapped.
In the current code it does not make any difference, since they are
always used together.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Home routers based on ARM SoCs like BCM4708 also have bcma bus with core
supported by bgmac.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On ARM SoCs with bgmac Ethernet hardware we don't have any normal PHY.
There is always a switch attached but it's not even controlled over MDIO
like in case of MIPS devices.
We need a fixed PHY to be able to send/receive packets from the switch.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
net/core/sysctl_net_core.c
net/ipv4/inet_diag.c
The be_main.c conflict resolution was really tricky. The conflict
hunks generated by GIT were very unhelpful, to say the least. It
split functions in half and moved them around, when the real actual
conflict only existed solely inside of one function, that being
be_map_pci_bars().
So instead, to resolve this, I checked out be_main.c from the top
of net-next, then I applied the be_main.c changes from 'net' since
the last time I merged. And this worked beautifully.
The inet_diag.c and sysctl_net_core.c conflicts were simple
overlapping changes, and were easily to resolve.
Signed-off-by: David S. Miller <davem@davemloft.net>
E1x chips (57710, 57711(E)) have no support for encapsulation
offload. bnx2x incorrectly advertises the support as available.
Setting of those features is conditional on "!CHIP_IS_E1x(bp)", but
the bp struct is not initialized yet at this point and consequently
any chip passes the check.
The check must use the "chip_is_e1x" local variable instead to work
correctly.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for Hardware Filter Block (HFB) so that incoming Rx traffic
can be matched and directed to desired Rx queues.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Delay the update of the TDMA producer index unless this is the last SKB
in a batch, or the queue is already stopped. Move the check for whether
the queue should be stopped before the xmit_more check to avoid locking
the transmit queue in case there was a SKB submitted which has xmit_more
set.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to have both bcmgenet_xmit_single() and
bcmgenet_xmit_frag() perform a free_bds decrement and a prod_index
increment by one. In case one of these functions fails to map a SKB or
fragment for transmit, we will return and exit bcmgenet_xmit() with an
error.
We can therefore safely use our local copy of nr_frags to know by how
much we should decrement the number of free buffers available, and by
how much the producer count must be incremented and do this in the tail
of bcmgenet_xmit().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, bcmgenet_desc_rx() calls bcmgenet_rx_refill() at the end of
Rx packet processing loop, after the current Rx packet has already been
passed to napi_gro_receive(). However, bcmgenet_rx_refill() might fail
to allocate a new Rx skb, thus leaving a hole on the Rx queue where no
valid Rx buffer exists.
To eliminate this situation:
1. Rewrite bcmgenet_rx_refill() to retain the current Rx skb on the Rx
queue if a new replacement Rx skb can't be allocated and DMA-mapped.
In this case, the data on the current Rx skb is effectively dropped.
2. Modify bcmgenet_desc_rx() to call bcmgenet_rx_refill() at the top of
Rx packet processing loop, so that the new replacement Rx skb is
already in place before the current Rx skb is processed.
Signed-off-by: Petri Gynther <pgynther@google.com>
Tested-by: Jaedon Shin <jaedon.shin@gmail.com>--
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bits 31:16 of RDMA_PROD_INDEX contain Rx discarded packet count, which
are the Rx packets that had to be dropped by MAC hardware since there
was no room on the Rx queue. Add code to collect this information into
the netdev stats.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cadence/macb.c
Overlapping changes in macb driver, mostly fixes and cleanups
in 'net' overlapping with the integration of at91_ether into
macb in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Add struct bcmgenet_rx_ring to hold all necessary information
for a single Rx queue.
2. Add bcmgenet_init_rx_queues() to initialize all Rx queues.
3. Modify bcmgenet_init_rx_ring() to initialize a single Rx queue.
4. Modify Rx interrupt path code to use per-queue data.
5. Modify bcmgenet_rx_refill() to use RxCB->bd_addr.
Signed-off-by: Petri Gynther <pgynther@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On my test environment the throughput of a file transfer drops
from 4.4MBps to 116KBps due the number of repeated warning
messages. This patch removes the warning messages as DMA works
correctly with addresses using 0xC0000000 bits.
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To test a checkpatch spelling patch, I ran codespell against
drivers/net/ethernet/.
$ git ls-files drivers/net/ethernet/ | \
while read file ; do \
codespell -w $file; \
done
I removed a false positive in e1000_hw.h
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for supporting multiple Rx queues:
1. Move the initialization of priv->num_rx_bds, priv->rx_bds, and
priv->rx_cbs from bcmgenet_init_rx_ring() to bcmgenet_init_dma()
since they are not specific to a single Rx queue. Mimics the Tx
init model where priv->num_tx_bds, priv->tx_bds, and priv->tx_cbs
are initialized in bcmgenet_init_dma().
2. Program DMA_MBUF_DONE_THRESH = 1 so that future Rx queues Q0-Q15
will get per-packet Rx interrupt.
3. Group DMA_START_ADDR, RDMA_READ_PTR, RDMA_WRITE_PTR, and DMA_END_ADDR
initialization together. Mimics the Tx init model.
4. There is 1-to-1 mapping between RxCBs and RxBDs.
Precalculate RxCB->bd_addr so that it can be used in the future.
Signed-off-by: Petri Gynther <pgynther@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for supporting multiple Rx queues, add GENET_Q16_RX_BD_CNT
and hw_params->rx_bds_per_q.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for supporting multiple Rx queues, adjust the call to
alloc_etherdev_mqs() to allow max GENET_MAX_MQ_CNT + 1 Rx queues.
The actual number of Rx queues in use is correctly adjusted with:
netif_set_real_num_rx_queues(priv->dev, priv->hw_params->rx_queues + 1);
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcmgenet driver doesn't yet support multiple Rx queues.
Set hw_params->rx_queues = 0 accordingly.
The default Rx queue (Q16) is still created and operational.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcmgenet_set_wol() correctly sets MPD_PW_EN when a password is specified
to match magic packets against, however, when we switch from a
password-matching to a matching without password we would leave this bit
turned on, and GENET would only match magic packets with passwords.
This can be reproduced using the following sequence:
ethtool -s eth0 wol g
ethtool -s eth0 wol s sopass 00:11:22:33:44:55
ethtool -s eth0 wol g
The simple fix is to clear the MPD_PWD_EN bit when WAKE_MAGICSECURE is
not set.
Fixes: c51de7f397 ("net: bcmgenet: add Wake-on-LAN support code")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EEH recovery for bnx2x based adapters is not reliable on all Power
systems using the default hot reset, which can result in an
unrecoverable EEH error. Forcing the use of fundamental reset
during EEH recovery fixes this.
Cc: stable<stable@vger.kernel.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Use c_index and ring->c_index to determine how many TxCBs/TxBDs are
ready for cleanup
- c_index = the current value of TDMA_CONS_INDEX
- TDMA_CONS_INDEX is HW-incremented and auto-wraparound (0x0-0xFFFF)
- ring->c_index = __bcmgenet_tx_reclaim() cleaned up to this point on
the previous invocation
2. Add bcmgenet_tx_ring->clean_ptr
- index of the next TxCB to be cleaned
- incremented as TxCBs/TxBDs are processed
- value always in range [ring->cb_ptr, ring->end_ptr]
3. Fix incrementing of dev->stats.tx_packets
- should be incremented only when tx_cb_ptr->skb != NULL
These changes simplify __bcmgenet_tx_reclaim(). Furthermore, Tx ring size
can now be any value.
With the old code, Tx ring size had to be a power-of-2:
num_tx_bds = ring->size;
c_index &= (num_tx_bds - 1);
last_c_index &= (num_tx_bds - 1);
Signed-off-by: Petri Gynther <pgynther@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case there was some tx buffer reclaimed and not enough rx packets
to consume the whole budget, napi_complete would not be called and
interrupts would be kept disabled, effectively resulting in the
network core never to call the poll callback again and no rx/tx
interrupts to be fired either.
Fix that by only accounting the rx work done in the poll callback.
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/rocker/rocker.c
The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the built-in function instead of memset.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bnx2 driver uses .ndo_fix_features to force enable of Rx VLAN tag
stripping when the card cannot disable it. The driver should remove
NETIF_F_HW_VLAN_CTAG_RX flag from hw_features instead so it is fixed
for the ethtool.
Cc: Sony Chacko <sony.chacko@qlogic.com>
Cc: Dept-HSGLinuxNICDev@qlogic.com
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 60b4ea1781 ("net: systemport: log RX buffer allocation and RX/TX DMA
failures") added a few software maintained statistics using
BCM_SYSPORT_STAT_MIB_RX and BCM_SYSPORT_STAT_MIB_TX. These statistics are read
from the hardware MIB counters, such that bcm_sysport_update_mib_counters() was
trying to read from a non-existing MIB offset for these counters.
Fix this by introducing a special type: BCM_SYSPORT_STAT_SOFT, similar to
BCM_SYSPORT_STAT_NETDEV, such that bcm_sysport_get_ethtool_stats will read from
the software mib.
Fixes: 60b4ea1781 ("net: systemport: log RX buffer allocation and RX/TX DMA failures")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 44c8bc3ce3 ("net: bcmgenet: log RX buffer allocation and RX/TX dma
failures") added a few software maintained statistics using
BCMGENET_STAT_MIB_RX and BCMGENET_STAT_MIB_TX. These statistics are read from
the hardware MIB counters, such that bcmgenet_update_mib_counters() was trying
to read from a non-existing MIB offset for these counters.
Fix this by introducing a special type: BCMGENET_STAT_SOFT, similar to
BCMGENET_STAT_NETDEV, such that bcmgenet_get_ethtool_stats will read from the
software mib.
Fixes: 44c8bc3ce3 ("net: bcmgenet: log RX buffer allocation and RX/TX dma failures")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds bcmgenet_tx_poll for the tx_rings. This can reduce the
interrupt load and send xmit in network stack on time. This also
separated for the completion of tx_ring16 from bcmgenet_poll.
The bcmgenet_tx_reclaim of tx_ring[{0,1,2,3}] operative by an interrupt
is to be not more than a certain number TxBDs. It is caused by too
slowly reclaiming the transmitted skb. Therefore, performance
degradation of xmit after 605ad7f ("tcp: refine TSO autosizing").
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcmgenet_hw_params->bds_cnt and GENET_DEFAULT_BD_CNT are used only in Tx init.
Rename them accordingly:
- bcmgenet_hw_params->bds_cnt => bcmgenet_hw_params->tx_bds_per_q
- GENET_DEFAULT_BD_CNT => GENET_Q16_TX_BD_CNT
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is 1-to-1 mapping between TxCBs and TxBDs. Precalculate TxCB->bd_addr
once in bcmgenet_init_dma() instead of doing it over and over needlessly in
bcmgenet_get_txcb().
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Rename bcmgenet_init_multiq() to bcmgenet_init_tx_queues()
2. Fix bcmgenet_init_tx_queues() function description
3. Move Tx default queue init inside bcmgenet_init_tx_queues()
4. Modify bcmgenet_init_dma() to call bcmgenet_init_tx_queues()
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Simplify function description
2. Rename function parameter write_ptr to start_ptr to better indicate use
3. Remove unnecessary local variable first_bd
4. Remove out-of-place comment "Unclassified traffic goes to ring 16"
5. Fix TDMA_WRITE_PTR register init
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates BNX2 driver version to 2.2.6 and CNIC driver version
to 2.5.21.
Signed-off-by: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not enable filter SORT MODE in chip init routine. This patch addresses an
issue where BCM5716 sporadically drops packets when changing multicast list.
Signed-off-by: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides additional changes as a part of BNX2 and CNIC driver
re-branding effort.
Signed-off-by: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3_init_one() calls tg3_halt() without tp->lock despite its assumption
and causes deadlock.
If lockdep is enabled, a warning like this shows up before the stall:
[ BUG: bad unlock balance detected! ]
3.19.0test #3 Tainted: G E
-------------------------------------
insmod/369 is trying to release lock (&(&tp->lock)->rlock) at:
[<ffffffffa02d5a1d>] tg3_chip_reset+0x14d/0x780 [tg3]
but there are no more locks to release!
tg3_init_one() doesn't call tg3_halt() under normal situation but
during kexec kdump I hit this problem.
Fixes: 932f19de ("tg3: Release tp->lock before invoking synchronize_irq()")
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Northstar (Broadcom's ARM architecture) we need to manually enable
all cores. Code for that is already in place, but the condition for it
was wrong.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the normal {} instead of a macro to terminate an array.
Remove the macro too.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the normal {} instead of a macro to terminate an array.
Remove the macro too.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch fixes following sparse warnings:
bnx2x_main.c:9172:6: warning: symbol 'bnx2x_stop_ptp' was not declared. Should it be static?
bnx2x_main.c:13321:6: warning: symbol 'bnx2x_register_phc' was not declared. Should it be static?
bnx2x_main.c:14638:5: warning: symbol 'bnx2x_enable_ptp_packets' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/arm/boot/dts/imx6sx-sdb.dts
net/sched/cls_bpf.c
Two simple sets of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
With the commit d75b1ade56 ("net: less interrupt masking in NAPI") napi
repoll is done only when work_done == budget. When in busy_poll is we return 0
in napi_poll. We should return budget.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IRQs should only get activated when there is nothing to poll in the
queue any more and to after every poll.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi should get registered before the netdev and not after.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/xen-netfront.c
Minor overlapping changes in xen-netfront.c, mostly to do
with some buffer management changes alongside the split
of stats into TX and RX.
Signed-off-by: David S. Miller <davem@davemloft.net>
synchronize_irq() can sleep waiting, for pending IRQ handlers so driver
should release the tp->lock spin lock before invoking synchronize_irq()
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently tg3_reset_task() uses only tp->lock for synchronizing with code
paths like tg3_open() etc. But since tp->lock is released before doing
synchronize_irq(), rtnl_lock should be taken in tg3_reset_task() to
synchronize it with other code paths.
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to avoid the race between tg3_timer() and the execution paths
which does not invoke tg3_timer_stop() and releases tp->lock before
calling synchronize_irq()
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same macros are used for rx as well. So rename it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move init and deinit of PTP support from open/close functions
to probe/remove funcs to avoid removing/re-adding of associated PTP
device(s) during ifup/ifdown.
v2: tg3_ptp_init call moved to correct place (thx. Prashant)
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the driver to use the new and improved method
for adjusting the offset of a timecounter.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
