The resilient nexthop group torture tests in fib_nexthop.sh exposed a
possible division by zero while replacing a resilient group [1]. The
division by zero occurs when the data path sees a resilient nexthop
group with zero buckets.
The tests replace a resilient nexthop group in a loop while traffic is
forwarded through it. The tests do not specify the number of buckets
while performing the replacement, resulting in the kernel allocating a
stub resilient table (i.e, 'struct nh_res_table') with zero buckets.
This table should never be visible to the data path, but the old nexthop
group (i.e., 'oldg') might still be used by the data path when the stub
table is assigned to it.
Fix this by only assigning the stub table to the old nexthop group after
making sure the group is no longer used by the data path.
Tested with fib_nexthops.sh:
Tests passed: 222
Tests failed: 0
[1]
divide error: 0000 [#1] PREEMPT SMP KASAN
CPU: 0 PID: 1850 Comm: ping Not tainted 5.14.0-custom-10271-ga86eb53057fe #1107
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-4.fc34 04/01/2014
RIP: 0010:nexthop_select_path+0x2d2/0x1a80
[...]
Call Trace:
fib_select_multipath+0x79b/0x1530
fib_select_path+0x8fb/0x1c10
ip_route_output_key_hash_rcu+0x1198/0x2da0
ip_route_output_key_hash+0x190/0x340
ip_route_output_flow+0x21/0x120
raw_sendmsg+0x91d/0x2e10
inet_sendmsg+0x9e/0xe0
__sys_sendto+0x23d/0x360
__x64_sys_sendto+0xe1/0x1b0
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
Cc: stable@vger.kernel.org
Fixes: 283a72a559 ("nexthop: Add implementation of resilient next-hop groups")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The process will cause napi.state to contain NAPI_STATE_SCHED and
not in the poll_list, which will cause napi_disable() to get stuck.
The prefix "NAPI_STATE_" is removed in the figure below, and
NAPI_STATE_HASHED is ignored in napi.state.
CPU0 | CPU1 | napi.state
===============================================================================
napi_disable() | | SCHED | NPSVC
napi_enable() | |
{ | |
smp_mb__before_atomic(); | |
clear_bit(SCHED, &n->state); | | NPSVC
| napi_schedule_prep() | SCHED | NPSVC
| napi_poll() |
| napi_complete_done() |
| { |
| if (n->state & (NPSVC | | (1)
| _BUSY_POLL))) |
| return false; |
| ................ |
| } | SCHED | NPSVC
| |
clear_bit(NPSVC, &n->state); | | SCHED
} | |
| |
napi_schedule_prep() | | SCHED | MISSED (2)
(1) Here return direct. Because of NAPI_STATE_NPSVC exists.
(2) NAPI_STATE_SCHED exists. So not add napi.poll_list to sd->poll_list
Since NAPI_STATE_SCHED already exists and napi is not in the
sd->poll_list queue, NAPI_STATE_SCHED cannot be cleared and will always
exist.
1. This will cause this queue to no longer receive packets.
2. If you encounter napi_disable under the protection of rtnl_lock, it
will cause the entire rtnl_lock to be locked, affecting the overall
system.
This patch uses cmpxchg to implement napi_enable(), which ensures that
there will be no race due to the separation of clear two bits.
Fixes: 2d8bff1269 ("netpoll: Close race condition between poll_one_napi and napi_disable")
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Reviewed-by: Dust Li <dust.li@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Makefile uses TEST_PROGS instead of TEST_GEN_PROGS to define
executables. TEST_PROGS is for shell scripts that need to be
installed and run by the common lib.mk framework. The common
framework doesn't touch TEST_PROGS when it does build and clean.
As a result "make kselftest-clean" and "make clean" fail to remove
executables. Run and install work because the common framework runs
and installs TEST_PROGS. Build works because the Makefile defines
"all" rule which is unnecessary if TEST_GEN_PROGS is used.
Use TEST_GEN_PROGS so the common framework can handle build/run/
install/clean properly.
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Any link state change that's done prior to net device registration
isn't reflected on the state, thus the operational state is left
obsolete, with 'UNKNOWN' status.
To resolve the issue, query link state from FW upon open operations
to ensure operational state is updated.
Fixes: c27a02cd94 ("mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC")
Signed-off-by: Lama Kayal <lkayal@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the args to fprintf(). Splitting the message ends up passing
incorrect arg for "sigurg %d" and an extra arg overall. The test
result message ends up incorrect.
test_unix_oob.c: In function ‘main’:
test_unix_oob.c:274:43: warning: format ‘%d’ expects argument of type ‘int’, but argument 3 has type ‘char *’ [-Wformat=]
274 | fprintf(stderr, "Test 3 failed, sigurg %d len %d OOB %c ",
| ~^
| |
| int
| %s
275 | "atmark %d\n", signal_recvd, len, oob, atmark);
| ~~~~~~~~~~~~~
| |
| char *
test_unix_oob.c:274:19: warning: too many arguments for format [-Wformat-extra-args]
274 | fprintf(stderr, "Test 3 failed, sigurg %d len %d OOB %c ",
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the inclusion of nvmem handling into the mac-address getter
function of_get_mac_address() by
commit d01f449c00 ("of_net: add NVMEM support to of_get_mac_address")
it is now possible to get a -EPROBE_DEFER return code. Which did cause
bgmac to assign a random ethernet address.
This exact issue happened on my Meraki MR32. The nvmem provider is
an EEPROM (at24c64) which gets instantiated once the module
driver is loaded... This happens once the filesystem becomes available.
With this patch, bgmac_probe() will propagate the -EPROBE_DEFER error.
Then the driver subsystem will reschedule the probe at a later time.
Cc: Petr Štetiar <ynezz@true.cz>
Cc: Michael Walle <michael@walle.cc>
Fixes: d01f449c00 ("of_net: add NVMEM support to of_get_mac_address")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 86f8b1c01a ("net: dsa: Do not make user port errors fatal")
decided it was fine to ignore errors on certain ports that fail to
probe, and go on with the ports that do probe fine.
Commit fb6ec87f72 ("net: dsa: Fix type was not set for devlink port")
noticed that devlink_port_type_eth_set(dlp, dp->slave); does not get
called, and devlink notices after a timeout of 3600 seconds and prints a
WARN_ON. So it went ahead to unregister the devlink port. And because
there exists an UNUSED port flavour, we actually re-register the devlink
port as UNUSED.
Commit 08156ba430 ("net: dsa: Add devlink port regions support to
DSA") added devlink port regions, which are set up by the driver and not
by DSA.
When we trigger the devlink port deregistration and reregistration as
unused, devlink now prints another WARN_ON, from here:
devlink_port_unregister:
WARN_ON(!list_empty(&devlink_port->region_list));
So the port still has regions, which makes sense, because they were set
up by the driver, and the driver doesn't know we're unregistering the
devlink port.
Somebody needs to tear them down, and optionally (actually it would be
nice, to be consistent) set them up again for the new devlink port.
But DSA's layering stays in our way quite badly here.
The options I've considered are:
1. Introduce a function in devlink to just change a port's type and
flavour. No dice, devlink keeps a lot of state, it really wants the
port to not be registered when you set its parameters, so changing
anything can only be done by destroying what we currently have and
recreating it.
2. Make DSA cache the parameters passed to dsa_devlink_port_region_create,
and the region returned, keep those in a list, then when the devlink
port unregister needs to take place, the existing devlink regions are
destroyed by DSA, and we replay the creation of new regions using the
cached parameters. Problem: mv88e6xxx keeps the region pointers in
chip->ports[port].region, and these will remain stale after DSA frees
them. There are many things DSA can do, but updating mv88e6xxx's
private pointers is not one of them.
3. Just let the driver do it (i.e. introduce a very specific method
called ds->ops->port_reinit_as_unused, which unregisters its devlink
port devlink regions, then the old devlink port, then registers the
new one, then the devlink port regions for it). While it does work,
as opposed to the others, it's pretty horrible from an API
perspective and we can do better.
4. Introduce a new pair of methods, ->port_setup and ->port_teardown,
which in the case of mv88e6xxx must register and unregister the
devlink port regions. Call these 2 methods when the port must be
reinitialized as unused.
Naturally, I went for the 4th approach.
Fixes: 08156ba430 ("net: dsa: Add devlink port regions support to DSA")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MODULE_DEVICE_TABLE already creates proper alias for platform
driver. Having another MODULE_ALIAS causes the alias to be duplicated.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Foster says:
====================
ocelot phylink fixes
When the ocelot driver was migrated to phylink, e6e12df625 ("net:
mscc: ocelot: convert to phylink") there were two additional writes to
registers that became stale. One write was to DEV_CLOCK_CFG and one was
to ANA_PFC_PCF_CFG.
Both of these writes referenced the variable "speed" which originally
was set to OCELOT_SPEED_{10,100,1000,2500}. These macros expand to
values of 3, 2, 1, or 0, respectively. After the update, the variable
speed is set to SPEED_{10,100,1000,2500} which expand to 10, 100, 1000,
and 2500. So invalid values were getting written to the two registers,
which would lead to either a lack of functionality or undefined
funcationality.
Fixing these values was the intent of v1 of this patch set - submitted
as "[PATCH v1 net] net: ethernet: mscc: ocelot: bug fix when writing MAC
speed"
During that review it was determined that both writes were actually
unnecessary. DEV_CLOCK_CFG is a duplicate write, so can be removed
entirely. This was accidentally submitted as as a new, lone patch titled
"[PATCH v1 net] net: mscc: ocelot: remove buggy duplicate write to
DEV_CLOCK_CFG". This is part of what is considered v2 of this patch set.
Additionally, the write to ANA_PFC_PFC_CFG is also unnecessary. Priority
flow contol is disabled, so configuring it is useless and should be
removed. This was also submitted as a new, lone patch titled "[PATCH v1
net] net: mscc: ocelot: remove buggy and useless write to ANA_PFC_PFC_CFG".
This is the rest of what is considered v2 of this patch set.
v3
Identical to v2, but fixes the patch numbering to v3 and submitting the
two changes as a patch set.
v2
Note: I misunderstood and submitted two new "v1" patches instead of a
single "v2" patch set.
- Remove the buggy writes altogher
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When updating ocelot to use phylink, a second write to DEV_CLOCK_CFG was
mistakenly left in. It used the variable "speed" which, previously, would
would have been assigned a value of OCELOT_SPEED_1000. In phylink the
variable is be SPEED_1000, which is invalid for the
DEV_CLOCK_LINK_SPEED macro. Removing it as unnecessary and buggy.
Fixes: e6e12df625 ("net: mscc: ocelot: convert to phylink")
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A useless write to ANA_PFC_PFC_CFG was left in while refactoring ocelot to
phylink. Since priority flow control is disabled, writing the speed has no
effect.
Further, it was using ethtool.h SPEED_ instead of OCELOT_SPEED_ macros,
which are incorrectly offset for GENMASK.
Lastly, for priority flow control to properly function, some scenarios
would rely on the rate adaptation from the PCS while the MAC speed would
be fixed. So it isn't used, and even if it was, neither "speed" nor
"mac_speed" are necessarily the correct values to be used.
Fixes: e6e12df625 ("net: mscc: ocelot: convert to phylink")
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
lock_sock_fast() and lock_sock_nested() contain lockdep annotations for the
sock::sk_lock.owned 'mutex'. sock::sk_lock.owned is not a regular mutex. It
is just lockdep wise equivalent. In fact it's an open coded trivial mutex
implementation with some interesting features.
sock::sk_lock.slock is a regular spinlock protecting the 'mutex'
representation sock::sk_lock.owned which is a plain boolean. If 'owned' is
true, then some other task holds the 'mutex', otherwise it is uncontended.
As this locking construct is obviously endangered by lock ordering issues as
any other locking primitive it got lockdep annotated via a dedicated
dependency map sock::sk_lock.dep_map which has to be updated at the lock
and unlock sites.
lock_sock_nested() is a straight forward 'mutex' lock operation:
might_sleep();
spin_lock_bh(sock::sk_lock.slock)
while (!try_lock(sock::sk_lock.owned)) {
spin_unlock_bh(sock::sk_lock.slock);
wait_for_release();
spin_lock_bh(sock::sk_lock.slock);
}
The lockdep annotation for sock::sk_lock.owned is for unknown reasons
_after_ the lock has been acquired, i.e. after the code block above and
after releasing sock::sk_lock.slock, but inside the bottom halves disabled
region:
spin_unlock(sock::sk_lock.slock);
mutex_acquire(&sk->sk_lock.dep_map, subclass, 0, _RET_IP_);
local_bh_enable();
The placement after the unlock is obvious because otherwise the
mutex_acquire() would nest into the spin lock held region.
But that's from the lockdep perspective still the wrong place:
1) The mutex_acquire() is issued _after_ the successful acquisition which
is pointless because in a dead lock scenario this point is never
reached which means that if the deadlock is the first instance of
exposing the wrong lock order lockdep does not have a chance to detect
it.
2) It only works because lockdep is rather lax on the context from which
the mutex_acquire() is issued. Acquiring a mutex inside a bottom halves
and therefore non-preemptible region is obviously invalid, except for a
trylock which is clearly not the case here.
This 'works' stops working on RT enabled kernels where the bottom halves
serialization is done via a local lock, which exposes this misplacement
because the 'mutex' and the local lock nest the wrong way around and
lockdep complains rightfully about a lock inversion.
The placement is wrong since the initial commit a5b5bb9a05 ("[PATCH]
lockdep: annotate sk_locks") which introduced this.
Fix it by moving the mutex_acquire() in front of the actual lock
acquisition, which is what the regular mutex_lock() operation does as well.
lock_sock_fast() is not that straight forward. It looks at the first glance
like a convoluted trylock operation:
spin_lock_bh(sock::sk_lock.slock)
if (!sock::sk_lock.owned)
return false;
while (!try_lock(sock::sk_lock.owned)) {
spin_unlock_bh(sock::sk_lock.slock);
wait_for_release();
spin_lock_bh(sock::sk_lock.slock);
}
spin_unlock(sock::sk_lock.slock);
mutex_acquire(&sk->sk_lock.dep_map, subclass, 0, _RET_IP_);
local_bh_enable();
return true;
But that's not the case: lock_sock_fast() is an interesting optimization
for short critical sections which can run with bottom halves disabled and
sock::sk_lock.slock held. This allows to shortcut the 'mutex' operation in
the non contended case by preventing other lockers to acquire
sock::sk_lock.owned because they are blocked on sock::sk_lock.slock, which
in turn avoids the overhead of doing the heavy processing in release_sock()
including waking up wait queue waiters.
In the contended case, i.e. when sock::sk_lock.owned == true the behavior
is the same as lock_sock_nested().
Semantically this shortcut means, that the task acquired the 'mutex' even
if it does not touch the sock::sk_lock.owned field in the non-contended
case. Not telling lockdep about this shortcut acquisition is hiding
potential lock ordering violations in the fast path.
As a consequence the same reasoning as for the above lock_sock_nested()
case vs. the placement of the lockdep annotation applies.
The current placement of the lockdep annotation was just copied from
the original lock_sock(), now renamed to lock_sock_nested(),
implementation.
Fix this by moving the mutex_acquire() in front of the actual lock
acquisition and adding the corresponding mutex_release() into
unlock_sock_fast(). Also document the fast path return case with a comment.
Reported-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: netdev@vger.kernel.org
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The file sja1105.txt was converted to nxp,sja1105.yaml.
Signed-off-by: Alejandro Concepcion-Rodriguez <asconcepcion@acoro.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
When IGC=y and PTP_1588_CLOCK=m, the ptp_*() interface family is
not available to the igc driver. Make this driver depend on
PTP_1588_CLOCK_OPTIONAL so that it will build without errors.
Various igc commits have used ptp_*() functions without checking
that PTP_1588_CLOCK is enabled. Fix all of these here.
Fixes these build errors:
ld: drivers/net/ethernet/intel/igc/igc_main.o: in function `igc_msix_other':
igc_main.c:(.text+0x6494): undefined reference to `ptp_clock_event'
ld: igc_main.c:(.text+0x64ef): undefined reference to `ptp_clock_event'
ld: igc_main.c:(.text+0x6559): undefined reference to `ptp_clock_event'
ld: drivers/net/ethernet/intel/igc/igc_ethtool.o: in function `igc_ethtool_get_ts_info':
igc_ethtool.c:(.text+0xc7a): undefined reference to `ptp_clock_index'
ld: drivers/net/ethernet/intel/igc/igc_ptp.o: in function `igc_ptp_feature_enable_i225':
igc_ptp.c:(.text+0x330): undefined reference to `ptp_find_pin'
ld: igc_ptp.c:(.text+0x36f): undefined reference to `ptp_find_pin'
ld: drivers/net/ethernet/intel/igc/igc_ptp.o: in function `igc_ptp_init':
igc_ptp.c:(.text+0x11cd): undefined reference to `ptp_clock_register'
ld: drivers/net/ethernet/intel/igc/igc_ptp.o: in function `igc_ptp_stop':
igc_ptp.c:(.text+0x12dd): undefined reference to `ptp_clock_unregister'
ld: drivers/platform/x86/dell/dell-wmi-privacy.o: in function `dell_privacy_wmi_probe':
Fixes: 64433e5bf4 ("igc: Enable internal i225 PPS")
Fixes: 60dbede0c4 ("igc: Add support for ethtool GET_TS_INFO command")
Fixes: 87938851b6 ("igc: enable auxiliary PHC functions for the i225")
Fixes: 5f2958052c ("igc: Add basic skeleton for PTP")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Ederson de Souza <ederson.desouza@intel.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Cc: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only struct dim_sample member that does not get
initialized by dim_update_sample() is comp_ctr. (There
is special API to initialize comp_ctr:
dim_update_sample_with_comps(), and it is currently used
only for RDMA.) comp_ctr is used to compute curr_stats->cmps
and curr_stats->cpe_ratio (see dim_calc_stats()) which in
turn are consumed by the rdma_dim_*() API. Therefore,
functionally, the net_dim*() API consumers are not affected.
Nevertheless, fix the computation of statistics based
on an uninitialized variable, even if the mentioned statistics
are not used at the moment.
Fixes: ae0e6a5d16 ("enetc: Add adaptive interrupt coalescing")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
irq_set_affinity_hit() stores a reference to the cpumask_t
parameter in the irq descriptor, and that reference can be
accessed later from irq_affinity_hint_proc_show(). Since
the cpu_mask parameter passed to irq_set_affinity_hit() has
only temporary storage (it's on the stack memory), later
accesses to it are illegal. Thus reads from the corresponding
procfs affinity_hint file can result in paging request oops.
The issue is fixed by the get_cpu_mask() helper, which provides
a permanent storage for the cpumask_t parameter.
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We try to use build_skb() if we had sufficient tailroom. But we forget
to release the unused pages chained via private in big mode which will
leak pages. Fixing this by release the pages after building the skb in
big mode.
Cc: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Fixes: fb32856b16 ("virtio-net: page_to_skb() use build_skb when there's sufficient tailroom")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When re-entering the main loop of xenvif_tx_check_gop() a 2nd time, the
special considerations for the head of the SKB no longer apply. Don't
mistakenly report ERROR to the frontend for the first entry in the list,
even if - from all I can tell - this shouldn't matter much as the overall
transmit will need to be considered failed anyway.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean says:
====================
Make DSA switch drivers compatible with masters which unregister on shutdown
Changes in v2:
- fix build for b53_mmap
- use unregister_netdevice_many
It was reported by Lino here:
https://lore.kernel.org/netdev/20210909095324.12978-1-LinoSanfilippo@gmx.de/
that when the DSA master attempts to unregister its net_device on
shutdown, DSA should prevent that operation from succeeding because it
holds a reference to it. This hangs the shutdown process.
This issue was essentially introduced in commit 2f1e8ea726 ("net: dsa:
link interfaces with the DSA master to get rid of lockdep warnings").
The present series patches all DSA drivers to handle that case,
depending on whether those drivers were introduced before or after the
offending commit, a different Fixes: tag is specified for them.
The approach taken by this series solves the issue in essentially the
same way as Lino's patches, except for three key differences:
- this series takes a more minimal approach in what is done on shutdown,
we do not attempt a full tree teardown as that is not strictly
necessary. I might revisit this if there are compelling reasons to do
otherwise
- this series fixes the issues for all DSA drivers, not just KSZ9897
- this series works even if the ->remove driver method gets called for
the same device too, not just ->shutdown. This is really possible to
happen for SPI device drivers, and potentially possible for other bus
device drivers too.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 2f1e8ea726 ("net: dsa: link interfaces with the DSA
master to get rid of lockdep warnings"), DSA gained a requirement which
it did not fulfill, which is to unlink itself from the DSA master at
shutdown time.
Since the Arrow SpeedChips XRS700x driver was introduced after the bad
commit, it has never worked with DSA masters which decide to unregister
their net_device on shutdown, effectively hanging the reboot process.
To fix that, we need to call dsa_switch_shutdown.
These devices can be connected by I2C or by MDIO, and if I search for
I2C or MDIO bus drivers that implement their ->shutdown by redirecting
it to ->remove I don't see any, however this does not mean it would not
be possible. To be compatible with that pattern, it is necessary to
implement an "if this then not that" scheme, to avoid ->remove and
->shutdown from being called both for the same struct device.
Fixes: ee00b24f32 ("net: dsa: add Arrow SpeedChips XRS700x driver")
Link: https://lore.kernel.org/netdev/20210909095324.12978-1-LinoSanfilippo@gmx.de/
Reported-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 2f1e8ea726 ("net: dsa: link interfaces with the DSA
master to get rid of lockdep warnings"), DSA gained a requirement which
it did not fulfill, which is to unlink itself from the DSA master at
shutdown time.
Since the Microchip sub-driver for KSZ8863 was introduced after the bad
commit, it has never worked with DSA masters which decide to unregister
their net_device on shutdown, effectively hanging the reboot process.
To fix that, we need to call dsa_switch_shutdown.
Since this driver expects the MDIO bus to be backed by mdio_bitbang, I
don't think there is currently any MDIO bus driver which implements its
->shutdown by redirecting it to ->remove, but in any case, to be
compatible with that pattern, it is necessary to implement an "if this
then not that" scheme, to avoid ->remove and ->shutdown from being
called both for the same struct device.
Fixes: 60a3647600 ("net: dsa: microchip: Add Microchip KSZ8863 SMI based driver support")
Link: https://lore.kernel.org/netdev/20210909095324.12978-1-LinoSanfilippo@gmx.de/
Reported-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 2f1e8ea726 ("net: dsa: link interfaces with the DSA
master to get rid of lockdep warnings"), DSA gained a requirement which
it did not fulfill, which is to unlink itself from the DSA master at
shutdown time.
Since the hellcreek driver was introduced after the bad commit, it has
never worked with DSA masters which decide to unregister their
net_device on shutdown, effectively hanging the reboot process.
Hellcreek is a platform device driver, so we probably cannot have the
oddities of ->shutdown and ->remove getting both called for the exact
same struct device. But to be in line with the pattern from the other
device drivers which are on slow buses, implement the same "if this then
not that" pattern of either running the ->shutdown or the ->remove hook.
The driver's current ->remove implementation makes that very easy
because it already zeroes out its device_drvdata on ->remove.
Fixes: e4b27ebc78 ("net: dsa: Add DSA driver for Hirschmann Hellcreek switches")
Link: https://lore.kernel.org/netdev/20210909095324.12978-1-LinoSanfilippo@gmx.de/
Reported-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lino reports that on his system with bcmgenet as DSA master and KSZ9897
as a switch, rebooting or shutting down never works properly.
What does the bcmgenet driver have special to trigger this, that other
DSA masters do not? It has an implementation of ->shutdown which simply
calls its ->remove implementation. Otherwise said, it unregisters its
network interface on shutdown.
This message can be seen in a loop, and it hangs the reboot process there:
unregister_netdevice: waiting for eth0 to become free. Usage count = 3
So why 3?
A usage count of 1 is normal for a registered network interface, and any
virtual interface which links itself as an upper of that will increment
it via dev_hold. In the case of DSA, this is the call path:
dsa_slave_create
-> netdev_upper_dev_link
-> __netdev_upper_dev_link
-> __netdev_adjacent_dev_insert
-> dev_hold
So a DSA switch with 3 interfaces will result in a usage count elevated
by two, and netdev_wait_allrefs will wait until they have gone away.
Other stacked interfaces, like VLAN, watch NETDEV_UNREGISTER events and
delete themselves, but DSA cannot just vanish and go poof, at most it
can unbind itself from the switch devices, but that must happen strictly
earlier compared to when the DSA master unregisters its net_device, so
reacting on the NETDEV_UNREGISTER event is way too late.
It seems that it is a pretty established pattern to have a driver's
->shutdown hook redirect to its ->remove hook, so the same code is
executed regardless of whether the driver is unbound from the device, or
the system is just shutting down. As Florian puts it, it is quite a big
hammer for bcmgenet to unregister its net_device during shutdown, but
having a common code path with the driver unbind helps ensure it is well
tested.
So DSA, for better or for worse, has to live with that and engage in an
arms race of implementing the ->shutdown hook too, from all individual
drivers, and do something sane when paired with masters that unregister
their net_device there. The only sane thing to do, of course, is to
unlink from the master.
However, complications arise really quickly.
The pattern of redirecting ->shutdown to ->remove is not unique to
bcmgenet or even to net_device drivers. In fact, SPI controllers do it
too (see dspi_shutdown -> dspi_remove), and presumably, I2C controllers
and MDIO controllers do it too (this is something I have not researched
too deeply, but even if this is not the case today, it is certainly
plausible to happen in the future, and must be taken into consideration).
Since DSA switches might be SPI devices, I2C devices, MDIO devices, the
insane implication is that for the exact same DSA switch device, we
might have both ->shutdown and ->remove getting called.
So we need to do something with that insane environment. The pattern
I've come up with is "if this, then not that", so if either ->shutdown
or ->remove gets called, we set the device's drvdata to NULL, and in the
other hook, we check whether the drvdata is NULL and just do nothing.
This is probably not necessary for platform devices, just for devices on
buses, but I would really insist for consistency among drivers, because
when code is copy-pasted, it is not always copy-pasted from the best
sources.
So depending on whether the DSA switch's ->remove or ->shutdown will get
called first, we cannot really guarantee even for the same driver if
rebooting will result in the same code path on all platforms. But
nonetheless, we need to do something minimally reasonable on ->shutdown
too to fix the bug. Of course, the ->remove will do more (a full
teardown of the tree, with all data structures freed, and this is why
the bug was not caught for so long). The new ->shutdown method is kept
separate from dsa_unregister_switch not because we couldn't have
unregistered the switch, but simply in the interest of doing something
quick and to the point.
The big question is: does the DSA switch's ->shutdown get called earlier
than the DSA master's ->shutdown? If not, there is still a risk that we
might still trigger the WARN_ON in unregister_netdevice that says we are
attempting to unregister a net_device which has uppers. That's no good.
Although the reference to the master net_device won't physically go away
even if DSA's ->shutdown comes afterwards, remember we have a dev_hold
on it.
The answer to that question lies in this comment above device_link_add:
* A side effect of the link creation is re-ordering of dpm_list and the
* devices_kset list by moving the consumer device and all devices depending
* on it to the ends of these lists (that does not happen to devices that have
* not been registered when this function is called).
so the fact that DSA uses device_link_add towards its master is not
exactly for nothing. device_shutdown() walks devices_kset from the back,
so this is our guarantee that DSA's shutdown happens before the master's
shutdown.
Fixes: 2f1e8ea726 ("net: dsa: link interfaces with the DSA master to get rid of lockdep warnings")
Link: https://lore.kernel.org/netdev/20210909095324.12978-1-LinoSanfilippo@gmx.de/
Reported-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
MDIO-attached devices might have interrupts and other things that might
need quiesced when we kexec into a new kernel. Things are even more
creepy when those interrupt lines are shared, and in that case it is
absolutely mandatory to disable all interrupt sources.
Moreover, MDIO devices might be DSA switches, and DSA needs its own
shutdown method to unlink from the DSA master, which is a new
requirement that appeared after commit 2f1e8ea726 ("net: dsa: link
interfaces with the DSA master to get rid of lockdep warnings").
So introduce a ->shutdown method in the MDIO device driver structure.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After d12e1c4649 ("net: dsa: b53: Set correct number of ports in the
DSA struct") we stopped setting dsa_switch::num_ports to DSA_MAX_PORTS,
which created an off by one error between the statically allocated
bcm_sf2_priv::port_sts array (of size DSA_MAX_PORTS). When
dsa_is_cpu_port() is used, we end-up accessing an out of bounds member
and causing a NPD.
Fix this by iterating with the appropriate port count using
ds->num_ports.
Fixes: d12e1c4649 ("net: dsa: b53: Set correct number of ports in the DSA struct")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NXP Legal insists that the following are not fine:
- Saying "NXP Semiconductors" instead of "NXP", since the company's
registered name is "NXP"
- Putting a "(c)" sign in the copyright string
- Putting a comma in the copyright string
The only accepted copyright string format is "Copyright <year-range> NXP".
This patch changes the copyright headers in the networking files that
were sent by me, or derived from code sent by me.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If resource allocation and registration fail for a muxed tty device
(e.g. if there are no more minor numbers) the driver should not try to
deregister the never-registered (or already-deregistered) tty.
Fix up the error handling to avoid dereferencing a NULL pointer when
attempting to remove the character device.
Fixes: 72dc1c096c ("HSO: add option hso driver")
Cc: stable@vger.kernel.org # 2.6.27
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
tx timeout and slot time are currently specified in units of HZ. On
Alpha, HZ is defined as 1024. When building alpha:allmodconfig, this
results in the following error message.
drivers/net/hamradio/6pack.c: In function 'sixpack_open':
drivers/net/hamradio/6pack.c:71:41: error:
unsigned conversion from 'int' to 'unsigned char'
changes value from '256' to '0'
In the 6PACK protocol, tx timeout is specified in units of 10 ms and
transmitted over the wire:
https://www.linux-ax25.org/wiki/6PACK
Defining a value dependent on HZ doesn't really make sense, and
presumably comes from the (very historical) situation where HZ was
originally 100.
Note that the SIXP_SLOTTIME use explicitly is about 10ms granularity:
mod_timer(&sp->tx_t, jiffies + ((when + 1) * HZ) / 100);
and the SIXP_TXDELAY walue is sent as a byte over the wire.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With the new static annotation, the compiler warns when the functions
are actually unused:
drivers/gpu/drm/rockchip/cdn-dp-core.c:1123:12: error: 'cdn_dp_resume' defined but not used [-Werror=unused-function]
1123 | static int cdn_dp_resume(struct device *dev)
| ^~~~~~~~~~~~~
Mark them __maybe_unused to suppress that warning as well.
[ Not so 'new' static annotations any more, and I removed the part of
the patch that added __maybe_unused to cdn_dp_suspend(), because it's
used by the shutdown/remove code.
So only the resume function ends up possibly unused if CONFIG_PM isn't
set - Linus ]
Fixes: 7c49abb4c2 ("drm/rockchip: cdn-dp-core: Make cdn_dp_core_suspend/resume static")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some drivers pass a pointer to volatile data to virt_to_bus() and
virt_to_phys(), and that works fine. One exception is alpha. This
results in a number of compile errors such as
drivers/net/wan/lmc/lmc_main.c: In function 'lmc_softreset':
drivers/net/wan/lmc/lmc_main.c:1782:50: error:
passing argument 1 of 'virt_to_bus' discards 'volatile'
qualifier from pointer target type
drivers/atm/ambassador.c: In function 'do_loader_command':
drivers/atm/ambassador.c:1747:58: error:
passing argument 1 of 'virt_to_bus' discards 'volatile'
qualifier from pointer target type
Declare the parameter of virt_to_phys and virt_to_bus as pointer to
volatile to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver isn't enabled most places because of the ISA config
dependency, but alpha still has it. And I think the 'Jensen' actually
did have an ISA slot.
However, it doesn't build cleanly, because the "Vortex bus master" code
just casts the skb->data pointer to 'int':
outl((int) (skb->data), ioaddr + Wn7_MasterAddr);
which is all kinds of broken. Even on a good old traditional PC/AT it
would be broken because the high bits will be random kernel address
bits, but presumably the hardware ignores those bits. I mean, it's ISA.
We're talking 16MB dma limits. The "good old days".
Make the build happy with this kind of craziness by using the proper
isa_virt_to_bus() handling that the full bus master code uses anyway
(the Vortex bus mastering is a limited special case).
Who knows, this might even work.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
One patch which fixes a build warning when using the PAGE0 pointer.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQS86RI+GtKfB8BJu973ErUQojoPXwUCYUNgkQAKCRD3ErUQojoP
X1J+AQCJol1vKuAJQQEXPrB6s1Hu/gkQpOc/MrmNXUj5ZpgH/QD/V3JQzHMOQNpx
uo3UgZ7sg+GnhJ1NIQ2zjXSBitAoaQI=
=GGF7
-----END PGP SIGNATURE-----
Merge tag 'for-5.15/parisc-4' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fix from Helge Deller:
"Fix a build warning when using the PAGE0 pointer"
* tag 'for-5.15/parisc-4' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Use absolute_pointer() to define PAGE0
The network interface managed by the mlxbf_gige driver can
get into a problem state where traffic does not flow.
In this state, the interface will be up and enabled, but
will stop processing received packets. This problem state
will happen if three specific conditions occur:
1) driver has received more than (N * RxRingSize) packets but
less than (N+1 * RxRingSize) packets, where N is an odd number
Note: the command "ethtool -g <interface>" will display the
current receive ring size, which currently defaults to 128
2) the driver's interface was disabled via "ifconfig oob_net0 down"
during the window described in #1.
3) the driver's interface is re-enabled via "ifconfig oob_net0 up"
This patch ensures that the driver's "valid_polarity" field is
cleared during the open() method so that it always matches the
receive polarity used by hardware. Without this fix, the driver
needs to be unloaded and reloaded to correct this problem state.
Fixes: f92e1869d7 ("Add Mellanox BlueField Gigabit Ethernet driver")
Reviewed-by: Asmaa Mnebhi <asmaa@nvidia.com>
Signed-off-by: David Thompson <davthompson@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Checking tunnel offloading, it turns out that offloading doesn't work
as expected. The following script allows to reproduce the issue.
Call it as `testscript DEVICE LOCALIP REMOTEIP NETMASK'
=== SNIP ===
if [ $# -ne 4 ]
then
echo "Usage $0 DEVICE LOCALIP REMOTEIP NETMASK"
exit 1
fi
DEVICE="$1"
LOCAL_ADDRESS="$2"
REMOTE_ADDRESS="$3"
NWMASK="$4"
echo "Driver: $(ethtool -i ${DEVICE} | awk '/^driver:/{print $2}') "
ethtool -k "${DEVICE}" | grep tx-udp
echo
echo "Set up NIC and tunnel..."
ip addr add "${LOCAL_ADDRESS}/${NWMASK}" dev "${DEVICE}"
ip link set "${DEVICE}" up
sleep 2
ip link add vxlan1 type vxlan id 42 \
remote "${REMOTE_ADDRESS}" \
local "${LOCAL_ADDRESS}" \
dstport 0 \
dev "${DEVICE}"
ip addr add fc00::1/64 dev vxlan1
ip link set vxlan1 up
sleep 2
rm -f vxlan.pcap
echo "Running tcpdump and iperf3..."
( nohup tcpdump -i any -w vxlan.pcap >/dev/null 2>&1 ) &
sleep 2
iperf3 -c fc00::2 >/dev/null
pkill tcpdump
echo
echo -n "Max. Paket Size: "
tcpdump -r vxlan.pcap -nnle 2>/dev/null \
| grep "${LOCAL_ADDRESS}.*> ${REMOTE_ADDRESS}.*OTV" \
| awk '{print $8}' | awk -F ':' '{print $1}' \
| sort -n | tail -1
echo
ip link del vxlan1
ip addr del ${LOCAL_ADDRESS}/${NWMASK} dev "${DEVICE}"
=== SNAP ===
The expected outcome is
Max. Paket Size: 64904
This is what you see on igb, the code igc has been taken from.
However, on igc the output is
Max. Paket Size: 1516
so the GSO aggregate packets are segmented by the kernel before calling
igc_xmit_frame. Inside the subsequent call to igc_tso, the check for
skb_is_gso(skb) fails and the function returns prematurely.
It turns out that this occurs because the feature flags aren't set
entirely correctly in igc_probe. In contrast to the original code
from igb_probe, igc_probe neglects to set the flags required to allow
tunnel offloading.
Setting the same flags as igb fixes the issue on igc.
Fixes: 34428dff36 ("igc: Add GSO partial support")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Tested-by: Corinna Vinschen <vinschen@redhat.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the assert from the callback priv lookup function since it does
not require RTNL lock and is already protected by flow_indr_block_lock.
This will avoid warnings from being emitted to dmesg if the driver
registers its callback after an ingress qdisc was created for a
netdevice.
The warnings started after the following patch was merged:
commit 74fc4f8287 ("net: Fix offloading indirect devices dependency on qdisc order creation")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was used but never set. The hardcoded value from before the dawn of
time was non-standard; the usual name for cross-tools is $TRIPLET-$TOOL
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Should not use comparison of unsigned expressions < 0.
Signed-off-by: Xiang wangx <wangxiang@cdjrlc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers:
- cmos: fix a locking issue
-----BEGIN PGP SIGNATURE-----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=sw2n
-----END PGP SIGNATURE-----
Merge tag 'rtc-5.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC fix from Alexandre Belloni:
"Fix a locking issue in the cmos rtc driver"
* tag 'rtc-5.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: cmos: Disable irq around direct invocation of cmos_interrupt()
Sometimes when unbinding the mv88e6xxx driver on Turris MOX, these error
messages appear:
mv88e6085 d0032004.mdio-mii:12: port 1 failed to delete be:79:b4:9e:9e:96 vid 1 from fdb: -2
mv88e6085 d0032004.mdio-mii:12: port 1 failed to delete be:79:b4:9e:9e:96 vid 0 from fdb: -2
mv88e6085 d0032004.mdio-mii:12: port 1 failed to delete d8:58:d7:00:ca:6d vid 100 from fdb: -2
mv88e6085 d0032004.mdio-mii:12: port 1 failed to delete d8:58:d7:00:ca:6d vid 1 from fdb: -2
mv88e6085 d0032004.mdio-mii:12: port 1 failed to delete d8:58:d7:00:ca:6d vid 0 from fdb: -2
(and similarly for other ports)
What happens is that DSA has a policy "even if there are bugs, let's at
least not leak memory" and dsa_port_teardown() clears the dp->fdbs and
dp->mdbs lists, which are supposed to be empty.
But deleting that cleanup code, the warnings go away.
=> the FDB and MDB lists (used for refcounting on shared ports, aka CPU
and DSA ports) will eventually be empty, but are not empty by the time
we tear down those ports. Aka we are deleting them too soon.
The addresses that DSA complains about are host-trapped addresses: the
local addresses of the ports, and the MAC address of the bridge device.
The problem is that offloading those entries happens from a deferred
work item scheduled by the SWITCHDEV_FDB_DEL_TO_DEVICE handler, and this
races with the teardown of the CPU and DSA ports where the refcounting
is kept.
In fact, not only it races, but fundamentally speaking, if we iterate
through the port list linearly, we might end up tearing down the shared
ports even before we delete a DSA user port which has a bridge upper.
So as it turns out, we need to first tear down the user ports (and the
unused ones, for no better place of doing that), then the shared ports
(the CPU and DSA ports). In between, we need to ensure that all work
items scheduled by our switchdev handlers (which only run for user
ports, hence the reason why we tear them down first) have finished.
Fixes: 161ca59d39 ("net: dsa: reference count the MDB entries at the cross-chip notifier level")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210914134726.2305133-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts commit 3ac8eed625, which did
more than it said on the box, and not only it replaced to_phy_driver
with phydev->drv, but it also removed the "!drv" check, without actually
explaining why that is fine.
That patch in fact breaks suspend/resume on any system which has PHY
devices with no drivers bound.
The stack trace is:
Unable to handle kernel NULL pointer dereference at virtual address 00000000000000e8
pc : mdio_bus_phy_suspend+0xd8/0xec
lr : dpm_run_callback+0x38/0x90
Call trace:
mdio_bus_phy_suspend+0xd8/0xec
dpm_run_callback+0x38/0x90
__device_suspend+0x108/0x3cc
dpm_suspend+0x140/0x210
dpm_suspend_start+0x7c/0xa0
suspend_devices_and_enter+0x13c/0x540
pm_suspend+0x2a4/0x330
Examples why that assumption is not fine:
- There is an MDIO bus with a PHY device that doesn't have a specific
PHY driver loaded, because mdiobus_register() automatically creates a
PHY device for it but there is no specific PHY driver in the system.
Normally under those circumstances, the generic PHY driver will be
bound lazily to it (at phy_attach_direct time). But some Ethernet
drivers attach to their PHY at .ndo_open time. Until then it, the
to-be-driven-by-genphy PHY device will not have a driver. The blamed
patch amounts to saying "you need to open all net devices before the
system can suspend, to avoid the NULL pointer dereference".
- There is any raw MDIO device which has 'plausible' values in the PHY
ID registers 2 and 3, which is located on an MDIO bus whose driver
does not set bus->phy_mask = ~0 (which prevents auto-scanning of PHY
devices). An example could be a MAC's internal MDIO bus with PCS
devices on it, for serial links such as SGMII. PHY devices will get
created for those PCSes too, due to that MDIO bus auto-scanning, and
although those PHY devices are not used, they do not bother anybody
either. PCS devices are usually managed in Linux as raw MDIO devices.
Nonetheless, they do not have a PHY driver, nor does anybody attempt
to connect to them (because they are not a PHY), and therefore this
patch breaks that.
The goal itself of the patch is questionable, so I am going for a
straight revert. to_phy_driver does not seem to have a need to be
replaced by phydev->drv, in fact that might even trigger code paths
which were not given too deep of a thought.
For instance:
phy_probe populates phydev->drv at the beginning, but does not clean it
up on any error (including EPROBE_DEFER). So if the phydev driver
requests probe deferral, phydev->drv will remain populated despite there
being no driver bound.
If a system suspend starts in between the initial probe deferral request
and the subsequent probe retry, we will be calling the phydev->drv->suspend
method, but _before_ any phydev->drv->probe call has succeeded.
That is to say, if the phydev->drv is allocating any driver-private data
structure in ->probe, it pretty much expects that data structure to be
available in ->suspend. But it may not. That is a pretty insane
environment to present to PHY drivers.
In the code structure before the blamed patch, mdio_bus_phy_may_suspend
would just say "no, don't suspend" to any PHY device which does not have
a driver pointer _in_the_device_structure_ (not the phydev->drv). That
would essentially ensure that ->suspend will never get called for a
device that has not yet successfully completed probe. This is the code
structure the patch is returning to, via the revert.
Fixes: 3ac8eed625 ("net: phy: Uniform PHY driver access")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210914140515.2311548-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
DSA supports connecting to a phy-handle, and has a fallback to a non-OF
based method of connecting to an internal PHY on the switch's own MDIO
bus, if no phy-handle and no fixed-link nodes were present.
The -ENODEV error code from the first attempt (phylink_of_phy_connect)
is what triggers the second attempt (phylink_connect_phy).
However, when the first attempt returns a different error code than
-ENODEV, this results in an unbalance of calls to phylink_create and
phylink_destroy by the time we exit the function. The phylink instance
has leaked.
There are many other error codes that can be returned by
phylink_of_phy_connect. For example, phylink_validate returns -EINVAL.
So this is a practical issue too.
Fixes: aab9c4067d ("net: dsa: Plug in PHYLINK support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20210914134331.2303380-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The qnx4 directory entries are 64-byte blocks that have different
contents depending on the a status byte that is in the last byte of the
block.
In particular, a directory entry can be either a "link info" entry with
a 48-byte name and pointers to the real inode information, or an "inode
entry" with a smaller 16-byte name and the full inode information.
But the code was written to always just treat the directory name as if
it was part of that "inode entry", and just extend the name to the
longer case if the status byte said it was a link entry.
That work just fine and gives the right results, but now that gcc is
tracking data structure accesses much more, the code can trigger a
compiler error about using up to 48 bytes (the long name) in a structure
that only has that shorter name in it:
fs/qnx4/dir.c: In function ‘qnx4_readdir’:
fs/qnx4/dir.c:51:32: error: ‘strnlen’ specified bound 48 exceeds source size 16 [-Werror=stringop-overread]
51 | size = strnlen(de->di_fname, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from fs/qnx4/qnx4.h:3,
from fs/qnx4/dir.c:16:
include/uapi/linux/qnx4_fs.h:45:25: note: source object declared here
45 | char di_fname[QNX4_SHORT_NAME_MAX];
| ^~~~~~~~
which is because the source code doesn't really make this whole "one of
two different types" explicit.
Fix this by introducing a very explicit union of the two types, and
basically explaining to the compiler what is really going on.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The sparc mdesc code does pointer games with 'struct mdesc_hdr', but
didn't describe to the compiler how that header is then followed by the
data that the header describes.
As a result, gcc is now unhappy since it does stricter pointer range
tracking, and doesn't understand about how these things work. This
results in various errors like:
arch/sparc/kernel/mdesc.c: In function ‘mdesc_node_by_name’:
arch/sparc/kernel/mdesc.c:647:22: error: ‘strcmp’ reading 1 or more bytes from a region of size 0 [-Werror=stringop-overread]
647 | if (!strcmp(names + ep[ret].name_offset, name))
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
which are easily avoided by just describing 'struct mdesc_hdr' better,
and making the node_block() helper function look into that unsized
data[] that follows the header.
This makes the sparc64 build happy again at least for my cross-compiler
version (gcc version 11.2.1).
Link: https://lore.kernel.org/lkml/CAHk-=wi4NW3NC0xWykkw=6LnjQD6D_rtRtxY9g8gQAJXtQMi8A@mail.gmail.com/
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge absolute_pointer macro series from Guenter Roeck:
"Kernel test builds currently fail for several architectures with error
messages such as the following.
drivers/net/ethernet/i825xx/82596.c: In function 'i82596_probe':
arch/m68k/include/asm/string.h:72:25: error:
'__builtin_memcpy' reading 6 bytes from a region of size 0
[-Werror=stringop-overread]
Such warnings may be reported by gcc 11.x for string and memory
operations on fixed addresses if gcc's builtin functions are used for
those operations.
This series introduces absolute_pointer() to fix the problem.
absolute_pointer() disassociates a pointer from its originating symbol
type and context, and thus prevents gcc from making assumptions about
pointers passed to memory operations"
* emailed patches from Guenter Roeck <linux@roeck-us.net>:
alpha: Use absolute_pointer to define COMMAND_LINE
alpha: Move setup.h out of uapi
net: i825xx: Use absolute_pointer for memcpy from fixed memory location
compiler.h: Introduce absolute_pointer macro
alpha:allmodconfig fails to build with the following error
when using gcc 11.x.
arch/alpha/kernel/setup.c: In function 'setup_arch':
arch/alpha/kernel/setup.c:493:13: error:
'strcmp' reading 1 or more bytes from a region of size 0
Avoid the problem by declaring COMMAND_LINE as absolute_pointer().
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
