This patch fixes a few obvious bugs in DSP loader stuff:
- Fix possible memory leaks in the error path
- Avoid double-free calls in dma_reset()
- Properly set/unset WC bits for DMA buffers
- Add missing error status checks
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Base the DSP firmware transfer and communication timeouts on jiffy values.
Signed-off-by: Ian Minett <ian_minett@creativelabs.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the HD Audio Device IDs for the Intel Wellsburg PCH
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A Haswell test machine showed that the invalid connection list, but
this time it has only a single pin on the codec, thus the former fixup
code doesn't work as it assumes the three pins blindly.
This patch splits the former fixup code to two parts:
- Enable eDP 1.2 for Haswell codec
- Fix the connection list of pins on Haswell codec;
the converter list is recorded dynamically in hdmi_add_cvt(), and
applied in hdmi_add_pin()
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some Haswell machines support more than one display outputs (HDMI or DP),
but its BIOS may not enable the codec's 2nd and 3rd pin and output cvt widgets.
This patch implements a board-specific fixup for Intel Haswell Machines:
If the hidden pins are not enabled by BIOS, the driver will enable them
and call common code to update the codec tree.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A codec may allow software to hide some unused pin/cvt widgets.
Sometimes BIOS does not enable the hidden widgets properly although they are
needed for the board. Thus the driver need to enable them as a board-specific
fixup and the whole tree will change.
This patch implements a common code for rereading codec widgets. So the fixup
code can call it after enabling the hidden widgets.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Help avoid noise from the power up of the capture path propagating through
into the start of the recording (especially noise caused by the ramp of
microphone biases) by keeping the capture muted until after we've finished
powering things up with DAPM in the same manner we do for playback. This
allows us to take advantage of soft mute support in the hardware more
effectively and is more consistent.
The core code using the existing digital mute operation is updated to take
advantage of this. Some additional cases in the soc-pcm code and suspend
will need separate handling but these are less practically relevant than
the main runtime stream start/stop case.
Rather than refactor the digital mute function in every single driver a
new operation is added for drivers taking advantage of this functionality,
the old operation should be phased out over time.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by Vinod Koul <vinod.koul@intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Currently we set the max number of connections to be 32, but there
seems codec that gives longer connection lists like AD1988, and we see
errors in proc output and else. (Though, in the case of AD1988, it's
a list of all codecs connected to a single vendor widget, so this must
be something fishy, but it's still valid from the h/w design POV.)
This patch tries to remove this restriction. For efficiency, we still
use the fixed size array in the parser, but takes a dynamic array when
the size is reported to be greater than that.
Now the fixed array size is found only in patch_hdmi.c, but it should
be fine, as the codec itself can't support so many pins.
Reported-by: Raymond Yau <superquad.vortex2@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Otherwise capture activity on a compressed DAI would mute any playback
on the same DAI.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Fix these two compile errors on s390 which does not have HAS_IOPORT
nor GENERIC_HARDIRQS:
sound/pci/lx6464es/lx6464es.c: In function ‘snd_lx6464es_free’:
sound/pci/lx6464es/lx6464es.c:565:2: error: implicit declaration of function ‘ioport_unmap’
sound/soc/codecs/wm8903.c: In function ‘wm8903_set_pdata_irq_trigger’:
sound/soc/codecs/wm8903.c:1954:9: error: implicit declaration of function ‘irq_get_irq_data’
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch completes the replacement of the existing max98090 driver,
by installing a more complete driver.
Signed-off-by: Jerry Wong <jerry.wong@maximintegrated.com>
Tested-by: Matthew Mowdy <matthew.mowdy@maximintegrated.com>
Reviewed-by: Ralph Birt <ralph.birt@maximintegrated.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch removes the existing max98090 driver prior to installing a more
complete one.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
sound/pci/hda/patch_ca0132.c: In function ‘ca0132_is_vnode_effective’:
sound/pci/hda/patch_ca0132.c:3331:15: warning: ‘nid’ may be used uninitialized in this function [-Wmaybe-uninitialized]
sound/pci/hda/patch_ca0132.c:4345:13: warning: ‘ca0132_download_dsp’ defined but not used [-Wunused-function]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The loopback list is referred by the VIA codec driver no matter
whether CONFIG_PM is set or not, thus we need to enable it always.
Otherwise it gets compile errors.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The wm->regs[] array has WM8766_REG_COUNT (16) elements not
WM8766_REG_RESET (31).
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It's mostly harmless to apply it for new models even if they have no
mic mute LED (just toggling an unused GPIO pin).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tegra already supports the common clock framework, but had issues:
1) The clock driver was located in arch/arm/mach-tegra/ rather than
drivers/clk/.
2) A single "Tegra clock" type was implemented, rather than separate
clock types for PLL, mux, divider, ... type in HW.
3) Clock lookups by device drivers were still driven by device name
and connection ID, rather than through device tree.
This pull request solves all three issues. This required some DT changes
to add clocks properties, and driver changes to request clocks more
"correctly". Finally, this rework allows all AUXDATA to be removed from
Tegra board files, and various duplicate clock lookup entries to be
removed from the driver.
This pull request is based on the previous pull request, with tag
tegra-for-3.9-cleanup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=s9hz
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.9-soc-ccf' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc
From Stephen Warren:
ARM: tegra: Common Clock Framework rework
Tegra already supports the common clock framework, but had issues:
1) The clock driver was located in arch/arm/mach-tegra/ rather than
drivers/clk/.
2) A single "Tegra clock" type was implemented, rather than separate
clock types for PLL, mux, divider, ... type in HW.
3) Clock lookups by device drivers were still driven by device name
and connection ID, rather than through device tree.
This pull request solves all three issues. This required some DT changes
to add clocks properties, and driver changes to request clocks more
"correctly". Finally, this rework allows all AUXDATA to be removed from
Tegra board files, and various duplicate clock lookup entries to be
removed from the driver.
This pull request is based on the previous pull request, with tag
tegra-for-3.9-cleanup.
* tag 'tegra-for-3.9-soc-ccf' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (31 commits)
clk: tegra30: remove unused TEGRA_CLK_DUPLICATE()s
clk: tegra20: remove unused TEGRA_CLK_DUPLICATE()s
ARM: tegra30: remove auxdata
ARM: tegra20: remove auxdata
ASoC: tegra: remove auxdata
staging: nvec: remove use of clk_get_sys
ARM: tegra: paz00: add clock information to DT
ARM: tegra: add clock properties to Tegra30 DT
ARM: tegra: add clock properties to Tegra20 DT
spi: tegra: do not use clock name to get clock
ARM: tegra: remove legacy clock code
ARM: tegra: migrate to new clock code
clk: tegra: add clock support for Tegra30
clk: tegra: add clock support for Tegra20
clk: tegra: add Tegra specific clocks
ARM: tegra: define Tegra30 CAR binding
ARM: tegra: define Tegra20 CAR binding
ARM: tegra: move tegra_cpu_car.h to linux/clk/tegra.h
ARM: tegra: add function to read chipid
ARM: tegra: fix compile error when disable CPU_IDLE
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/mach-tegra/board-dt-tegra20.c
arch/arm/mach-tegra/board-dt-tegra30.c
arch/arm/mach-tegra/common.c
arch/arm/mach-tegra/platsmp.c
drivers/clocksource/Makefile
The ASoC compressed API did not implement the copy callback in its
compressed ops which is required for DSPs that are not memory mapped.
This patch creates a local copy of the compress ops for each runtime and
modifies them with a copy callback as appropriate.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The same constraint is going to be set in the snd_dmaengine_pcm_open()
function, so there is no need to set it here as well.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
These days, GUIs such as Gnome sound settings want to be able to
show the correct jack status even when no streams are currently
running. I doubt this gives any measurable difference in power,
but if it does, the "Jack Detect" control can still be used to
turn polling off.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The VT1708 has no unsol event capability, and polling is set using
the "Jack Detect" alsamixer control. In order not to create
phantom Jack controls, temporary enable jackpoll during build_controls.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
From Kukjin Kim:
AS I commented, this makes <mach/*.h> local so that they could be removed.
* 'next/cleanup-header' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (26 commits)
ARM: S3C64XX: Fix missing header error with CONFIG_CPU_IDLE enabled
ARM: S3C64XX: make regs-syscon-power.h local
ARM: S3C64XX: make regs-sys.h local
ARM: S3C64XX: make regs-srom.h local
ARM: S3C64XX: make regs-modem.h local
ARM: S3C64XX: make regs-gpio-memport.h local
ARM: S3C64XX: make crag6410.h local
ARM: S3C24XX: remove dsc.c and make regs-dsc.h local
ARM: S3C24XX: remove idle.h
ARM: S3C2412: cleanup regs-s3c2412.h
ARM: S3C2416: remove regs-s3c2416-mem.h and regs-s3c2416.h
ARM: S3C24XX: make vr1000-cpld.h, vr1000-irq.h and vr1000-map.h local
ARM: S3C24XX: make otom-map.h local
ARM: S3C24XX: make osiris-cpld.h and osiris-map.h local
ARM: S3C24XX: make h1940.h and h1940-latch.h local
ARM: S3C24XX: make gta02.h local
ARM: S3C24XX: make bast-cpld.h, bast-irq.h and bast-map.h local
ARM: S3C24XX: make anubis-cpld, anubis-irq and anubis-map local
ARM: SAMSUNG: cleanup mach/gpio-fns.h gpio-track.h and gpio-nrs.h
ARM: SAMSUNG: cleanup mach/regs-audss.h file
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Allow the regmap API to use asynchronous I/O where supported to minimise
the delay between transfers, reducing firmware download times.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chris Rattray <crattray@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Convert MicBias widgets to supply widget.
On tlv320aic3x, Mic bias power on/off shares the same register bits
with output mic bias voltage. So, when power on mic bias, we need
reclaim it to voltage value.
Provide a new platform data so that the micbias voltage can be sent
according to board requirement. Now since tlv320aic3x codec driver
is DT aware, update dt files and functions to handle this new
"micbias-vg" platform data.
Because of sharing of bits, when enabling the micbias, voltage also
needs to be updated. So use SND_SOC_DAPM_POST_PMU & SND_SOC_DAPM_PRE_PMD
macro to create an event to handle this.
Since micbias is converted to supply widget, updated machine drivers as
well.
This change is runtime tested on da850-evm with audio loopback
(arecord|aplay) for confirmation.
Signed-off-by: Hebbar Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
disable clock and correct sequence when unload
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
correct the sequence when unload this module
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ssc private data has been set in ssc driver, this cause the error
private data set to ssc, remove it
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When build as module, it reports following error, using this patch
fix it
sound/soc/atmel/atmel-pcm-pdc.c:387: error: redefinition of 'atmel_pcm_pdc_platform_register'
sound/soc/atmel/atmel-pcm.h:95: note: previous definition of 'atmel_pcm_pdc_platform_register' was here
sound/soc/atmel/atmel-pcm-pdc.c:393: error: redefinition of 'atmel_pcm_pdc_platform_unregister'
sound/soc/atmel/atmel-pcm.h:99: note: previous definition of 'atmel_pcm_pdc_platform_unregister' was here
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Previously arizona_calc_fll() was checking if the target frequency is
exactly divisible by reference frequency, but should have been product
of the ratio and the reference frequency.
Also scale down the Lamba and Theta coefficients be under 16-bits in
order to match the registers.
Signed-off-by: Ryo Tsutsui <ryo.tsutsui@wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
... to be less confusing for the update path.
This new kconfig will choose CONFIG_SND_HDA_DSP_LOADER, which is
basically a device-independent feature in hda_intel.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd-aloop driver has no proper PM implementation, thus the PM resume
may trigger Oops due to leftover timer instance. This patch adds the
missing suspend/resume implementation.
Reported-and-tested-by: El boulangero <elboulangero@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit d45e6889ee ("ALSA: hda - Provide
the proper channel mapping for generic HDMI driver") added support for
custom channel maps in the HDA HDMI driver. Due to a mistake in an
'if' condition the custom map is always used even when no such map has
been set. This causes incorrect channel mapping for multichannel audio
by default.
Pass per_pin->chmap_set to hdmi_setup_channel_mapping() as a parameter
so that it can use it for detecting if a custom map has been set instead
of checking if map is NULL (which is never the case).
Reported-by: Staffan Lindberg <pike@xbmc.org>
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the driver detects and invalid ELD, it gives an open error.
But it forgot to release the assigned pin, converter and spdif ctls
before returning.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add new PCI ID 0x0a0c for Haswell ULT platform.
Signed-off-by: Wang Xingchao <xingchao.wang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The quirk for the Roland/Cakewalk A-PRO keyboards accidentally used the
wrong interface number, which prevented the driver from attaching to the
device.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: 2.6.37+ <stable@vger.kernel.org>
Some compilers complain when building sound for MOP500:
sound/soc/ux500/mop500.c:27:27:
fatal error: mop500_ab8500.h: No such file or directory
That file is actually in the local directory rather than include.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds runtime suspend to resume support for I2S.
I2S clk is disabled at suspend and enabled at resume.
Signed-off-by: R. Chandrasekar <rcsekar@samsung.com>
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The commit a08485d8 ("ASoC: Samsung: Do not register samsung audio dma
device as pdev") introduced compilation error.
Combination of CONFIG_CPU_S3C2440 and CONFIG_SND_S3C24XX_I2S
caused undefined symbols 's3c_i2sv2_register_dai' and 's3c2412_i2s_dai'
in sound/soc/samsung/s3c24xx-i2s.c.
This patch fixes the problem and makes S3C2440 I2S usable again. It does
not affect S3C2412 (aka I2S-v2).
Signed-off-by: Alexey Galakhov <agalakhov@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ASoC clock gate settings are continuous/gated only.
This patch decides it as bool, then, gated clock will be default.
Special thanks to Stephen
Cc: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Playing a mono stream on the TLV320AIC3x results in too fast playback rate.
Remove mono support so that mono streams can be played correctly on this codec.
Tested with imx-ssi (i.MX25) and TLV320AIC3104.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For non-snoop mode, we fiddle with the page attributes of CORB/RIRB
and the position buffer, but also the ring buffers. The problem is
that the current code blindly assumes that the buffer is contiguous.
However, the ring buffers may be SG-buffers, thus a wrong vmapped
address is passed there, leading to Oops.
This patch fixes the handling for SG-buffers.
Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=800701
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It looks like MODULE_SUPPORTED_DEVICES() is not implemented yet, but
still, having the entries in the list consistently separated by commas
and with balanced parenthesis won't hurt.
Signed-off-by: Antonio Ospite <ao2@amarulasolutions.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently we use LPIB forcibly for both playback and capture for
Poulsbo and Oaktrail devices, and this seems rather problematic.
The recent fix for LPIB delay count seems working well with these
devices, so let's enable it instead.
Reported-by: Martin Weishart <martin.weishart@telosalliance.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Update Kconfig file to enable I2S,PCM audio for wm8994 and spdif on all
samsung platforms.
Signed-off-by: Sangsu Park <sangsu4u.park@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add the basic device tree based lookup.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add support for device based discovery.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Configlink clock information is added to device tree. Get the clocks
using device node. Remove AUXDATA.
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Migrate Tegra clock support to drivers/clk/tegra, this involves
moving:
1. definition of tegra_cpu_car_ops to clk.c
2. definition of reset functions to clk-peripheral.c
3. change parent of cpu clock.
4. Remove legacy clock initialization.
5. Initialize clocks using DT.
6. Remove all instance of mach/clk.h
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
[swarren: use to_clk_periph_gate().]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
