* 'for-2.6.40' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: Unify input section names
percpu: Avoid extra NOP in percpu_cmpxchg16b_double
percpu: Cast away printk format warning
percpu: Always align percpu output section to PAGE_SIZE
Fix up fairly trivial conflict in arch/x86/include/asm/percpu.h as per Tejun
In mask/restore_ioapic_entries() we should be restoring ioapic
entries when ioapics[apic].saved_registers is not NULL.
Fix the typo and address the resume hang regression reported by
Linus.
This was not found sooner because the systems where these
changes were tested on kept the IO-APIC entries intact over
resume.
Reported-and-tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Daniel J Blueman <daniel.blueman@gmail.com>
Link: http://lkml.kernel.org/r/1306259131.7171.7.camel@sbsiddha-MOBL3.sc.intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (27 commits)
PCI: Don't use dmi_name_in_vendors in quirk
PCI: remove unused AER functions
PCI/sysfs: move bus cpuaffinity to class dev_attrs
PCI: add rescan to /sys/.../pci_bus/.../
PCI: update bridge resources to get more big ranges when allocating space (again)
KVM: Use pci_store/load_saved_state() around VM device usage
PCI: Add interfaces to store and load the device saved state
PCI: Track the size of each saved capability data area
PCI/e1000e: Add and use pci_disable_link_state_locked()
x86/PCI: derive pcibios_last_bus from ACPI MCFG
PCI: add latency tolerance reporting enable/disable support
PCI: add OBFF enable/disable support
PCI: add ID-based ordering enable/disable support
PCI hotplug: acpiphp: assume device is in state D0 after powering on a slot.
PCI: Set PCIE maxpayload for card during hotplug insertion
PCI/ACPI: Report _OSC control mask returned on failure to get control
x86/PCI: irq and pci_ids patch for Intel Panther Point DeviceIDs
PCI: handle positive error codes
PCI: check pci_vpd_pci22_wait() return
PCI: Use ICH6_GPIO_EN in ich6_lpc_acpi_gpio
...
Fix up trivial conflicts in include/linux/pci_ids.h: commit a6e5e2be44
moved the intel SMBUS ID definitons to the i2c-i801.c driver.
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, apic: Include module.h header in apic_flat_64.c
x86, apic: Make apic drivers static
x86, apic: Clean up bigsmp apic selection code
x86, apic: Use .apicdrivers section for the apic drivers list
x86, apic: Introduce .apicdrivers section to find the list of apic drivers
x86, x2apic: Move the common bits to x2apic.h
x86, x2apic: Minimize IPI register writes using cluster groups
x86, x2apic: Track the x2apic cluster sibling map
x86, x2apic: Remove duplicate code for IPI mask routines
x86, apic: Use probe routines to simplify apic selection
x86, ioapic: Consolidate mp_ioapic_routing[] into 'struct ioapic'
x86, ioapic: Consolidate gsi routing info into 'struct ioapic'
x86, ioapic: Consolidate mp_ioapics[] into 'struct ioapic'
x86, ioapic: Consolidate ioapic_saved_data[] into 'struct ioapic'
x86, ioapic: Add struct ioapic
x86, ioapic: Remove duplicate code for saving/restoring RTEs
x86, ioapic: Use ioapic_saved_data while enabling intr-remapping
x86, ioapic: Allocate ioapic_saved_data early
x86, ioapic: Fix potential resume deadlock
apic_flat_64.c needs to include module.h because it uses
EXPORT_SYMBOL_GPL().
This fixes these warnings on some !SMP randconfigs:
arch/x86/kernel/apic/apic_flat_64.c:31: warning: data definition has no type or storage class
arch/x86/kernel/apic/apic_flat_64.c:31: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/x86/kernel/apic/apic_flat_64.c:31: warning: parameter names (without types) in function declaration
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Link: http://lkml.kernel.org/r/20110523104300.dd532a99.randy.dunlap@oracle.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf tools: Fix sample size bit operations
perf tools: Fix ommitted mmap data update on remap
watchdog: Change the default timeout and configure nmi watchdog period based on watchdog_thresh
watchdog: Disable watchdog when thresh is zero
watchdog: Only disable/enable watchdog if neccessary
watchdog: Fix rounding bug in get_sample_period()
perf tools: Propagate event parse error handling
perf tools: Robustify dynamic sample content fetch
perf tools: Pre-check sample size before parsing
perf tools: Move evlist sample helpers to evlist area
perf tools: Remove junk code in mmap size handling
perf tools: Check we are able to read the event size on mmap
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
b43: fix comment typo reqest -> request
Haavard Skinnemoen has left Atmel
cris: typo in mach-fs Makefile
Kconfig: fix copy/paste-ism for dell-wmi-aio driver
doc: timers-howto: fix a typo ("unsgined")
perf: Only include annotate.h once in tools/perf/util/ui/browsers/annotate.c
md, raid5: Fix spelling error in comment ('Ofcourse' --> 'Of course').
treewide: fix a few typos in comments
regulator: change debug statement be consistent with the style of the rest
Revert "arm: mach-u300/gpio: Fix mem_region resource size miscalculations"
audit: acquire creds selectively to reduce atomic op overhead
rtlwifi: don't touch with treewide double semicolon removal
treewide: cleanup continuations and remove logging message whitespace
ath9k_hw: don't touch with treewide double semicolon removal
include/linux/leds-regulator.h: fix syntax in example code
tty: fix typo in descripton of tty_termios_encode_baud_rate
xtensa: remove obsolete BKL kernel option from defconfig
m68k: fix comment typo 'occcured'
arch:Kconfig.locks Remove unused config option.
treewide: remove extra semicolons
...
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Eliminate various 'set but not used' warnings
x86, SMEP: Fix section mismatch warnings
x86, amd: Use _safe() msr access for GartTlbWlk disable code
* 'kvm-updates/2.6.40' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (131 commits)
KVM: MMU: Use ptep_user for cmpxchg_gpte()
KVM: Fix kvm mmu_notifier initialization order
KVM: Add documentation for KVM_CAP_NR_VCPUS
KVM: make guest mode entry to be rcu quiescent state
KVM: x86 emulator: Make jmp far emulation into a separate function
KVM: x86 emulator: Rename emulate_grpX() to em_grpX()
KVM: x86 emulator: Remove unused arg from emulate_pop()
KVM: x86 emulator: Remove unused arg from writeback()
KVM: x86 emulator: Remove unused arg from read_descriptor()
KVM: x86 emulator: Remove unused arg from seg_override()
KVM: Validate userspace_addr of memslot when registered
KVM: MMU: Clean up gpte reading with copy_from_user()
KVM: PPC: booke: add sregs support
KVM: PPC: booke: save/restore VRSAVE (a.k.a. USPRG0)
KVM: PPC: use ticks, not usecs, for exit timing
KVM: PPC: fix exit accounting for SPRs, tlbwe, tlbsx
KVM: PPC: e500: emulate SVR
KVM: VMX: Cache vmcs segment fields
KVM: x86 emulator: consolidate segment accessors
KVM: VMX: Avoid reading %rip unnecessarily when handling exceptions
...
Before the conversion of the NMI watchdog to perf event, the
watchdog timeout was 5 seconds. Now it is 60 seconds. For my
particular application, netbooks, 5 seconds was a better
timeout. With a short timeout, we catch faults earlier and are
able to send back a panic. With a 60 second timeout, the user is
unlikely to wait and will instead hit the power button, causing
us to lose the panic info.
This change configures the NMI period to watchdog_thresh and
sets the softlockup_thresh to watchdog_thresh * 2. In addition,
watchdog_thresh was reduced to 10 seconds as suggested by Ingo
Molnar.
Signed-off-by: Mandeep Singh Baines <msb@chromium.org>
Cc: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/r/1306127423-3347-4-git-send-email-msb@chromium.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
LKML-Reference: <20110517071642.GF22305@elte.hu>
The setup_smep function gets calle at resume time too, and is thus not a
pure __init function. When marked as __init, it gets thrown out after
the kernel has initialized, and when the kernel is suspended and
resumed, the code will no longer be around, and we'll get a nice "kernel
tried to execute NX-protected page" oops because the page is no longer
marked executable.
Reported-and-tested-by: Parag Warudkar <parag.lkml@gmail.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: "H. Peter Anvin" <hpa@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The address of the gpte was already calculated and stored in ptep_user
before entering cmpxchg_gpte().
This patch makes cmpxchg_gpte() to use that to make it clear that we
are using the same address during walk_addr_generic().
Note that the unlikely annotations are used to show that the conditions
are something unusual rather than for performance.
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
We introduce em_jmp_far().
We also call this from em_grp45() to stop treating modrm_reg == 5 case
separately in the group 5 emulation.
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: Avi Kivity <avi@redhat.com>
The prototypes are changed appropriately.
We also replaces "goto grp45;" with simple em_grp45() call.
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: Avi Kivity <avi@redhat.com>
The opt of emulate_grp1a() is also removed.
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: Avi Kivity <avi@redhat.com>
In addition, one comma at the end of a statement is replaced with a
semicolon.
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: Avi Kivity <avi@redhat.com>
This way, we can avoid checking the user space address many times when
we read the guest memory.
Although we can do the same for write if we check which slots are
writable, we do not care write now: reading the guest memory happens
more often than writing.
[avi: change VERIFY_READ to VERIFY_WRITE]
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: Avi Kivity <avi@redhat.com>
When we optimized walk_addr_generic() by not using the generic guest
memory reader, we replaced copy_from_user() with get_user():
commit e30d2a170506830d5eef5e9d7990c5aedf1b0a51
KVM: MMU: Optimize guest page table walk
commit 15e2ac9a43d4d7d08088e404fddf2533a8e7d52e
KVM: MMU: Fix 64-bit paging breakage on x86_32
But as Andi pointed out later, copy_from_user() does the same as
get_user() as long as we give a constant size to it.
So we use copy_from_user() to clean up the code.
The only, noticeable, regression introduced by this is 64-bit gpte
reading on x86_32 hosts needed for PAE guests.
But this can be mitigated by implementing 8-byte get_user() for x86_32,
if needed.
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: Avi Kivity <avi@redhat.com>
Since the emulator now checks segment limits and access rights, it
generates a lot more accesses to the vmcs segment fields. Undo some
of the performance hit by cacheing those fields in a read-only cache
(the entire cache is invalidated on any write, or on guest exit).
Signed-off-by: Avi Kivity <avi@redhat.com>
Instead of separate accessors for the segment selector and cached descriptor,
use one accessor for both. This simplifies the code somewhat.
Signed-off-by: Avi Kivity <avi@redhat.com>
dump_vmcb isn't used outside this module, make it static.
Shrink text and object by ~1% by standardizing formats.
$ size arch/x86/kvm/svm.o*
text data bss dec hex filename
52910 580 10072 63562 f84a arch/x86/kvm/svm.o.new
53563 580 10072 64215 fad7 arch/x86/kvm/svm.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Fix regression introduced by
commit e30d2a170506830d5eef5e9d7990c5aedf1b0a51
KVM: MMU: Optimize guest page table walk
On x86_32, get_user() does not support 64-bit values and we fail to
build KVM at the point of 64-bit paging.
This patch fixes this by using get_user() twice for that condition.
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Reported-by: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
The CPUIDs for Centaur are added, and then the features of
PadLock hardware engine on VIA CPU, such as "ace", "ace_en"
and so on, can be passed into the kvm guest.
Signed-off-by: Brilly Wu <brillywu@viatech.com.cn>
Signed-off-by: Kary Jin <karyjin@viatech.com.cn>
Signed-off-by: Avi Kivity <avi@redhat.com>
mmio_index should be taken into account when copying data from
userspace.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Move all groups into a single field and handle them in a single place. This
saves bits when we add more group types (3 bits -> 7 groups types).
Signed-off-by: Avi Kivity <avi@redhat.com>
walk_addr_generic() is a hot path and is also hard for the cpu to predict -
some of the parameters (fetch_fault in particular) vary wildly from
invocation to invocation.
Add unlikely() annotations where appropriate; all walk failures are
considered unlikely, as are cases where we have to mark the accessed or
dirty bit, as they are slow paths both in kvm and on real processors.
Signed-off-by: Avi Kivity <avi@redhat.com>
For this, emulate_pusha/popa() are converted to em_pusha/popa().
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: Avi Kivity <avi@redhat.com>
In addition, the RET emulation is changed to call em_pop() to remove
the pop_instruction label.
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: Avi Kivity <avi@redhat.com>
The following instructions are changed to use opcode::execute.
Group 1 (80-83)
ADD (00-05), OR (08-0D), ADC (10-15), SBB (18-1D), AND (20-25),
SUB (28-2D), XOR (30-35), CMP (38-3D)
CMPS (A6-A7), SCAS (AE-AF)
The last two do the same as CMP in the emulator, so em_cmp() is used.
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch optimizes the guest page table walk by using get_user()
instead of copy_from_user().
With this patch applied, paging64_walk_addr_generic() has become
about 0.5us to 1.0us faster on my Phenom II machine with NPT on.
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: Avi Kivity <avi@redhat.com>
By reserving 0 as an invalid x86_intercept_stage, we no longer
need to store a valid flag in x86_intercept_map.
Signed-off-by: Avi Kivity <avi@redhat.com>
While it isn't defined, no need to force a #UD. If it becomes defined
in the future this can cause wierd problems for the guest.
Signed-off-by: Avi Kivity <avi@redhat.com>
arch/x86/kvm/emulate.c:2598: warning: integer constant is too large for 'long' type
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Commit 0b56652e33c72092956c651ab6ceb9f0ad081153 fails to build:
CC [M] arch/x86/kvm/emulate.o
arch/x86/kvm/emulate.c: In function 'x86_emulate_insn':
arch/x86/kvm/emulate.c:4095:25: error: macro "wbinvd" passed 1 arguments, but takes just 0
arch/x86/kvm/emulate.c:4095:3: warning: statement with no effect
make[2]: *** [arch/x86/kvm/emulate.o] Error 1
make[1]: *** [arch/x86/kvm] Error 2
make: *** [arch/x86] Error 2
Work around this for now.
Signed-off-by: Clemens Noss <cnoss@gmx.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch makes the cmpxchg_gpte() function aware of the
difference between l1-gfns and l2-gfns when nested
virtualization is in use. This fixes a potential
data-corruption problem in the l1-guest and makes the code
work correct (at least as correct as the hardware which is
emulated in this code) again.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
