[why]
The function is expected to return instance of the timing generator
therefore we shouldn't be returning boolean in integer function,
and we shouldn't be returning zero so changing it to -1.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The link setting will be modify after disable phy
and due to DP Compliance Fails.
[How]
Save and resotre link setting for disable link phy when link retraining.
Signed-off-by: Hugo Hu <hugo.hu@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want to know DP protocol version
[How]
In DC create we initialize a cap to indicate the max
DP protocol version supported
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DF team has produced more optimized latency numbers, for lpddr4
[How]
change the p-state laency in the lpddr4 wm table to the new latency
number
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need support for more color management in 10bit
surface.
[How]
Provide support for DePQ for 10bit surface
Signed-off-by: Reza Amini <Reza.Amini@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
During mode transition steer fifo could overflow. Quite often it
recovers by itself, but sometimes it doesn't.
[how]
Add steer fifo reset before unblanking the stream. Also add a short
delay when resetting dig resync fifo to make sure register writes
don't end up back-to-back, in which case the HW might miss the reset
request.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Bring this calculation in line with HW programming guide.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Previous Renoir chroma viewport workaround fixed an MPO flicker by
increasing the chroma viewport size. However, when the MPO plane is
rotated 180 degrees, the viewport is read in reverse. Since the workaround
increases viewport size, when reading in reverse it causes a vertical
chroma offset.
[HOW]
Pass rotation value to viewport set functions
Temporarily disable the chroma viewport w/a when hubp is rotated 180 degrees
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The variable mismatch assignment error.
[How]
To use uint32_t replace it.
Signed-off-by: Brandon Syu <Brandon.Syu@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DP spec requires 1000 symbols delay between the end of link training
and enabling FEC in the stream. Currently we are using 1 miliseconds
delay which is not accurate.
[how]
One lane RBR should have the maximum time for transmitting 1000 LL
codes which is 6.173 us. So using 7 microseconds delay instead of
1 miliseconds.
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Before was using HW counter value to determine the dprefclk. Which
take into account ss, but has large variation, not good enough for
generating audio dto. Also, the bios parser code to get the ss
percentage was not working.
[How]
After this change, dprefclk is hard coded, same as on RV. We don't
expect this to change on Renoir. Modified bios parser code to get
the right ss percentage.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
new sr and pstate latencies are optimized for the case when we are not
using lpddr4 memory
[How]
have two different wm tables, one for the lpddr case and one for
non lpddr case
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In dc_link_is_dp_sink_present, if dal_ddc_open fails, then
dal_gpio_destroy_ddc is called, destroying pin_data and pin_clock. They
are created only on dc_construct, and next aux access will cause a panic.
[How]
Instead of calling dal_gpio_destroy_ddc, call dal_ddc_close.
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When video_memory_type bw_params->vram_type
is assigned, wedistinguish between Ddr4MemType and LpDdr4MemType.
Because of this we will never report that we are using
LpDdr4MemType and never re-purpose WM set D
[How]
populate bios integrated info for renoir by adding the
revision number for renoir and use that integrated info
table instead of of asic_id to get the vram type
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On dcn21 this is programmed for tracebuffer support but isn't being
programmed on dcn20.
DMCUB execution hits an undefined address 65000000 on tracebuffer
access.
[How]
Program CW5.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Not having support for autoload isn't an error. If the DMUB firmware
doesn't support it then don't return DMUB_STATUS_INVALID.
[How]
Return DMUB_STATUS_OK when ->is_auto_load_done is NULL.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The wait for PHY init won't finish if the firmware doesn't support it.
[How]
Only hook this functionality up on DCN21 and move it out of DCN20.
For ASIC without support then this should return OK so we don't hang
while waiting in DC.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Black screen seen after display is disabled then re-enabled.
Caused by difference in link settings when
switching between different resolutions.
[How]
In PnP case, or whenever the display is
still enabled but the driver is unloaded,
disable link before re-enabling with new link settings.
Signed-off-by: Lucy Li <lucy.li@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Link training failed randomly when plugging USB-C display in/out.
[How]
If link training failed, reset PHY in link re-training.
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Wrong guards were causing the debug option not to run.
[How]
Changed the guard to the correct one, matching the rq, ttu, dlg regs struct
members that need to be guarded. Also log a message when validation starts.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
pstate_latency_us never gets updated from the hard coded value
in rn_clk_mgr.c
[how]
update the wm table's values before we do calculations with them
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
On ASICs where number of DSCs is the same as OPPs there's no need
for DSC resource management. Mappping 1-to-1 fixes mode-set- or S3-
-related issues for such platforms.
[how]
Map DSC resources 1-to-1 to pipes only if number of OPPs is the same
as number of DSCs. This will still keep other ASICs working.
A follow-up patch to fix mode-set issues on those ASICs will be
required if testing shows issues with mode set.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Dali is currently being misinterpreted as Renoir,
as a result uses wrong clk mgr constructor
[HOW]
Add check to init Dali as Raven2 before it can be misidentified
Clean up & fix Raven2 & Dali ASIC checks
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some function pointers in the hwss function pointer table are
meant to be hw sequencer entry points to be called from dc.
However some of those function pointers are not meant to
be entry points, but instead used as a code reuse/inheritance
tool called directly by other hwss functions, not by dc.
Therefore, we want a more clear separation of which functions
we determine to be interface functions vs the functions we
use within hwss.
[How]
DC interface functions will be stored in:
struct hw_sequencer_funcs
Functions used within HWSS will be stored in:
struct hwseq_private_funcs
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
First, to make code more consistent
Second, to get rid of those scenario where we create a second
local pointer to dc when it's already passed in.
[How]
Rename core_dc to dc
Remove duplicate local pointers to dc
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DF team has produced more optimized latency numbers.
[How]
Add sr latencies to the wm table, use different latencies
for different wm sets.
Also fix bb override from registery key for these latencies.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
NV10/14 has released. Its time to get NV10/14 bounding box
directly from code.
[How]
Retrieve NV10/14 bounding box data directly from code.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
NV14 is using its own ip params that's different from other
DCN2.0 ASICs.
[How]
Add ASIC revision check to make sure NV14 gets correct
ip params.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
NV14 IP Parameters are missing.
[How]
Add IP Parameters in.
Signed-off-by: Zhan liu <zhan.liu@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
"num_vmid" and "num_dsc" are missing within NV14's resource caps structure.
[How]
Add the missing parts.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The variable v_total is being initialized with a value that is never
read and it is being updated later with a new value. The initialization
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The msg_id field is being assigned twice. Fix this by replacing the second
assignment with an assignment to msg_size.
Addresses-Coverity: ("Unused value")
Fixes: 11a00965d2 ("drm/amd/display: Add PSP block to verify HDCP2.2 steps")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
NV14 is using its own ip params that's different from other
DCN2.0 ASICs.
[How]
Add ASIC revision check to make sure NV14 gets correct
ip params.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
NV14 IP Parameters are missing.
[How]
Add IP Parameters in.
Signed-off-by: Zhan liu <zhan.liu@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We don't use this upstream in the Linux kernel.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
"num_vmid" and "num_dsc" are missing within NV14's resource caps structure.
[How]
Add the missing parts.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This line of code was modified. However, comments
remained unchanged. As a result, comments and code are
mismatching.
[How]
Modifying comments to reflect code. At the same time,
explaining why the value was changed from 200ms to
3000ms.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
previously event_property_validate was only called after we enabled the display.
But after "Refactor HDCP to handle multiple displays per link" this function
can be called at any time. In certain cases we don't have a aconnector
[How]
Null check aconnector and exit early. This is ok because we only need to check the
ENABLED->DESIRED transition if a connector exists.
Fixes: b1abe5586f ("drm/amd/display: Refactor HDCP to handle multiple displays per link")
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dm_pp_get_clock_levels_by_type needs to add the default clocks
to the powerplay case as well. This was accidently dropped.
Fixes: b3ea88fef3 ("drm/amd/powerplay: add get_clock_by_type interface for display")
Bug: https://gitlab.freedesktop.org/drm/amd/issues/906
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
drivers/gpu/drm/amd/amdgpu/../display/modules/hdcp/hdcp_psp.c: In function mod_hdcp_hdcp2_enable_encryption:
drivers/gpu/drm/amd/amdgpu/../display/modules/hdcp/hdcp_psp.c:633:77: warning: variable msg_out set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/amd/amdgpu/../display/modules/hdcp/hdcp_psp.c: In function mod_hdcp_hdcp2_enable_dp_stream_encryption:
drivers/gpu/drm/amd/amdgpu/../display/modules/hdcp/hdcp_psp.c:710:77: warning: variable msg_out set but not used [-Wunused-but-set-variable]
It is never used, so remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clang warns:
../drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:1965:26: warning:
expression which evaluates to zero treated as a null pointer constant of
type 'struct dc_dsc_config *' [-Wnon-literal-null-conversion]
update->dsc_config = false;
^~~~~
../drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:1971:25: warning:
expression which evaluates to zero treated as a null pointer constant of
type 'struct dc_dsc_config *' [-Wnon-literal-null-conversion]
update->dsc_config = false;
^~~~~
2 warnings generated.
Fixes: f6fe4053b9 ("drm/amd/display: Use a temporary copy of the current state when updating DSC config")
Link: https://github.com/ClangBuiltLinux/linux/issues/777
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dm_pp_get_clock_levels_by_type needs to add the default clocks
to the powerplay case as well. This was accidently dropped.
Fixes: b3ea88fef3 ("drm/amd/powerplay: add get_clock_by_type interface for display")
Bug: https://gitlab.freedesktop.org/drm/amd/issues/906
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 1c42591591.
S/G display is not stable with the IOMMU enabled on some
platforms.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=205523
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Previous patch allowed to initialize debugfs entries on both MST
and SST connectors, but MST connectors get registered much later
which exposed an issue of debugfs entries being initialized in the
same folder.
[how]
Return SST debugfs entries' initialization back to where it was.
For MST connectors we should initialize debugfs entries in connector
register function after the connector is registered.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add codes to print the detail EDC info for the subblock of mmhub
v2: Move the EDC_CNT registers' defintion from mmhub_9_4 header
files to mmhub_1_0 ones. Add mmhub_v1_0_ prefix for the local
static variable and function.
v3: squash in DC fix
Signed-off-by: Dennis Li <dennis.li@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 1c42591591.
S/G display is not stable with the IOMMU enabled on some
platforms.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=205523
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
For MST connector atomic check we have to check a new CRTC state
instead of an old one, when checking if CRTC is disabled to
release VCPI slots allocated.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
static analysis throws the error below
Out-of-bounds read (OVERRUN)
Overrunning array of 5 bytes at byte offset 7 by dereferencing pointer
(uint64_t *)hdcp->auth.msg.hdcp1.bksv.
var n is going to contain r0p and bcaps. if they are non-zero the count
will be wrong
How]
Use memcpy instead to avoid this.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently we share rxstatus between HDMI and DP, so we use 16bits
The drm defines work with 1bytes at a time. So we need to
split the HDMI rxstatus into 2bytes before we can use drm defines
[How]
-create rxstatus for dp and hdmi. rxstatus for hdmi is split into bytes
using arrays.
-use drm_hdcp defines for the remaining structs
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
drm already has this define
[How]
drm Mask is 0x08 vs 0x0800. The reason is because drm mask
works on a byte. ^^
=======||
||
Since the first byte is always zero we can ignore it and only check the
second byte.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
These defines/macros exist already no need to redefine them
[How]
Use the defines/macros from drm_hdcp.h
-we share the rxstatus between HDMI and DP (2 bytes), But upstream
defines/macros for HDMI are for 1 byte. So we need to create a separate
rxstatus for HDMI
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The old way was to poll PSP and update the properties. But due to a
limitation in the PSP interface this doesn't work for MST.
[How]
According to PSP if set_encryption return success, the link is encrypted
and the only way it will not be is if we get a link loss(which we handle
already).
So this method should be good enough to report HDCP status.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Before we had a disable_type1 flag, this forced HDCP 2.2 to type0
There was no way to force type1.
[How]
Remove disable_type1 flag and instead add a flag to force type0/1.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to do this to support HDCP over MST
Currently we save a display per link, in a MST case we need to save
multiple displays per link.
[How]
We can create an array per link to cache the displays, but it
complicates the design. Instead we can use the module to cache the
displays.
Now we will always add all the displays to the module, but we use the
adjustment flag to disable hdcp on all of them before they are added.
When we want to enable hdcp we just query the display(cache), remove
it then add it back with different adjustments. Its the similar for
disable.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HDCP 2.2 uses type0 and type1 content type. This is passed to the receiver
to stream the proper content.
For example, in a MST case if the main
device is HDCP2.2 capable but the secondary device is only 1.4 capabale
we can use Type0
Type0 content: use HDCP 1.4 or HDCP2.2 type0
Type1 content: Only use HDCP 2.2 type1
[How]
We use the "hdcp content type" property in drm. We use the
disable_type1 flag in hdcp module to select the type based on the
properties.
For updating the property we use the same logic as 1.4, but now we
consider content_type as well and update the property if the
requirements are met
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HDCP 2.2 was disabled, we need to enable it
[How]
-Update display topology to support 2.2
-Unset hdcp2.disable in update_config
-Change logic of event_update_property, now we set the property to be
ENABLED for any level of encryption (2.2 or 1.4).
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HDCP is a bit finicky so we try it 3 times, this leads to a case where
if we fail the first time and pass the second time the error is still
shown in dmesg for the first failed attempt.
This leads to false positive errors.
[How]
Change the logging from ERROR to WARNING. Warnings are still shown in dmesg
to know what went wrong.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to log the state changes for 2.2
This patch extends the existing logging functions to handle
HDCP2.2.
[How]
We do this by adding if/else in the defines, and output the log
based on the hdcp version
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The module works like a state machine
+-------------+
------> | Execution.c | ------
| +-------------+ |
| V
+----+ +--------+ +--------------+
| DM | -----> | Hdcp.c | <------------ | Transition.c |
+----+ <----- +--------+ +--------------+
This patch adds the execution and transition files for 2.2
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need these to read and write to aux/i2c, during
authentication
[How]
Create read/write functions for all the steps
(Eg, h_prime, paring_info etc)
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
All the HDCP transactions should be verified using PSP
[How]
This patch adds the psp calls we need to verify the steps
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need some extra dmub_cmd_type for NV10
[How]
Add command table functions in DMUB firmware.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Xiong Yan <Xiong.Yan@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need to be able to enable native 422 for debugging purposes.
[How]
Add new dc_debug_options bool and check it in the get_dsc_enc_caps
function.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When updating DSC config, a new config has to be validated before proceeding
with applying the update. Validation, however, modifies the current state.
This means DSC config validation would affect pipe re-assignment, causing
intermittent screen corruption issues when ODM is required for DSC.
[how]
- Use a copy of the current state for modified DSC config validation
- Set the update type to FULL_UPDATE to correctly validate and set the
actual state used for committing the streams
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCN will hang if we access registers before PHY init is done.
So we need to spin or abort.
[How]
On hardware with DMCUB running and working we shouldn't time out
waiting for this to finish and we shouldn't hit the spin cycle.
If there's no hardware support then we should exit out of the function
early assuming that PHY init was already done elsewhere.
If we hit the timeout then there's likely a bug in firmware or software
and we need to debug - add errors and asserts as appropriate.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need validation that we are programming the expected values (rq, ttu, dlg)
from DML. This debug feature will output logs if we are programming
incorrect values and may help differentiate DAL issues from HW issues.
[How]
Dump relevant registers for each pipe with active stream. Compare current
reg values with the converted DML output. Log mismatches when found.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It is becoming increasingly hard to figure out which
function is called on the different DCN versions
[How]
1. Make function pointer table init in its own init.c file
2. Remove other scenarios in hwseq.c file that need to
include headers of other DCN versions. (If needed,
it should have been done via the function pointers)
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It's an interface violation to use infinite loops within DMUB
service functions and we'll lock up the kernel by doing so.
[How]
Revert the function back to its intended functionality.
Move the infinite loops into DC/DM as necessary.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
There can be a conflict between OS HDR multiplier and 3dlut HDR
multiplier, which are both sent to DC.
[HOW]
Instead of having dc determine which HDR multiplier to use, make the
decision in dm and send only the intended value in a surface update.
Store the current OS HDR multiplier and determine whether to use it or
the 3dlut's multiplier before sending the surface update to dc. Send
multiplier to dc in fixed31_32 format, dc then converts it to hw format.
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
need to send immediate SDP message via debugfs on Navi board.
[how]
hook up the DCN1x encoder function of sending immediate sdp
message to DCN2.
Signed-off-by: David (Dingchen) Zhang <dingchen.zhang@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
1. Add trace code enum for easy debugging.
2. Add trace during uC boot up, including loading phy FW
and dmcu FW.
3. Change cache memory type back to write back,
since write through has issue when resume from S0i3 100% hang after
3.2ms.
4. Change CW3 base address to hard code value to avoid memory overlap
with cw1.
5. Change polling phy init done to infinite loop to avoid dcn hang when
dmcub uC stalled.
6. Add dmcub FW dis-assembly file to repositatory for debug purpose.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There is a case where the margin is between 50 and 60, but applying the
workaround causes a hang. By increasing the threshold, we are blocking more
cases from switching p-state during active, but those cases will fall back
to switching during blank, which is fine.
[How]
- increase required margin from 50 to 60
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In the TEST_MSIC dpcd register field definition, the test equipment
has the option to choose between YCbCr601 or YCbCr709.
We will apply corresponding YCbCr coefficient based on this test
request.
[how]
Add a new input parameter in dc_link_dp_set_test_pattern to allow the
selection between different color space.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Too many construct functions which makes searching
difficult, especially on some debuggers.
[How]
Append all construct and destruct functions with dcn
number and object type to make each construct function
name unique
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Previous patch allowed to initialize debugfs entries on both MST
and SST connectors, but MST connectors get registered much later
which exposed an issue of debugfs entries being initialized in the
same folder.
[how]
Return SST debugfs entries' initialization back to where it was.
For MST connectors we should initialize debugfs entries in connector
register function after the connector is registered.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Hanging on RV for DTN driver verifier
[How]
Roll back change and investigate further
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In SST mode no idle pattern will be generated after link training if
DIG FE is not connected to DIG BE.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
We were missing debugfs files on MST connectors as the files
weren't initialized.
[how]
Move connector debugfs initialization into connoctor's
init helper function so it will be called by both SST and MST
connectors. Also move connector registration so it will be
registered before we create the entries.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
By default we shouldn't be trying to write secure registers during
DMUB hardware init.
[How]
Add a parameter to control whether we put the DMCUB into secure reset
and attempt to load CW0/CW1.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want to avoid reprogramming the cache window when possible.
We don't need to worry about it for S3 but we *do* need to worry about
it for S4 resume.
DM can check whether hardware should be reinitialized or store software
state when going to S4 to know whether we need to reprogram hardware.
[How]
Add helpers to the DMUB service to check hardware initialization state.
DM will hook it up later.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Changes in dc to allow for different cases where full update is
required.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When sending DCC with Stereo, DCC gets enabled but the meta addresses
are 0. This happens momentarily before the meta addresses are populated
with a valid address.
[How]
Add call validate_dcc_with_meta_address() in
copy_surface_update_to_plane() to check for surface address and DCC
change.
When DCC has changed, check if DCC enable is true but meta address is 0.
If so, we turn DCC enable to false. When surface address has changed, we
check if DCC enable is false but meta address is not 0. If so, we turn
DCC enable back to true. This will restore DCC enable to the proper
setting once the meta address is valid.
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HDMI 2.0 HF-VSDB in EDID defines supported color depths in YCBCR420 modes.
But we did not honor these bit masks when choosing pixel encoding.
HDMI 2.0 compliance tests with deep color and YCBCR420 failed as a result.
[How]
Cap color depth based on y420_dc_modes from EDID.
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Background color only takes effect in bottommost mpcc.
[How]
Update background color in bottommost mpcc.
Signed-off-by: Hugo Hu <hugo.hu@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For debug purpose, we need to check HUBP_CLOCK_ENABLE in DTN
log debugfs on Navi.
[How]
Add related register read in dcn20_hubp.c.
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Before we were reading registers specific to luma size, which caused a black line
to appear on the screen from time to time, as although the luma row height
is generally the same as the chroma row height for the video case, it will sometimes
be one more
[how]
Read the register specific for the chroma size
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
we want to increase the pte row plus 1 line if chroma viewport
height is integer multiple of the pte row height
[how]
instead of ceiling viewport height, we floor it. this allows
us to accommodate both cases: those where the chroma viewport
height is integer multiple of the pte row height and those where
it is not
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
An old display with no audio may not have an EDID with a CEA block, or
it may simply be too old to support audio. This is not a driver error,
so don't flag it as such.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=112140
References: ae2a349597 ("drm/amd: be quiet when no SAD block is found")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/amd/display/modules/color/color_gamma.c: In function build_freesync_hdr:
drivers/gpu/drm/amd/display/modules/color/color_gamma.c:830:20: warning: variable min_content set but not used [-Wunused-but-set-variable]
It is not used since commit 50575eb5b3 ("drm/amd/display:
Only use EETF when maxCL > max display")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/amd/display/dc/bios/bios_parser.c: In function bios_get_board_layout_info:
drivers/gpu/drm/amd/display/dc/bios/bios_parser.c:2743:22: warning: variable bp set but not used [-Wunused-but-set-variable]
It is introduced by commit 1eeedbcc20 ("drm/amd/display:
get board layout for edid emulation"), but never used,
so remove it.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/amd/display/dc/bios/bios_parser2.c: In function bios_get_board_layout_info:
drivers/gpu/drm/amd/display/dc/bios/bios_parser2.c:1826:22: warning: variable bp set but not used [-Wunused-but-set-variable]
It is introduced by commit 1eeedbcc20 ("drm/amd/display:
get board layout for edid emulation"), but never used,
so remove it.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.c: In function dm_determine_update_type_for_commit:
drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.c:6516:36: warning: variable old_plane_crtc set but not used [-Wunused-but-set-variable]
It is introduced by commit a87fa99387 ("drm/amd/display:
Build stream update and plane updates in dm"), but never used,
so remove it.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link.c: In function get_pbn_from_timing:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link.c:2364:11: warning:
variable bpc set but not used [-Wunused-but-set-variable]
It is not used since commit e49f69363a ("drm/amd/display: use
proper formula to calculate bandwidth from timing"), this also
remove get_color_depth(), which is only used here.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link_dp.c: In function dp_wa_power_up_0010FA:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link_dp.c:2320:35: warning:
variable ds_port set but not used [-Wunused-but-set-variable]
It is never used, so can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move the static keyword to the front of declarations.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is comparison expression that is duplicated and hence one
of the expressions can be removed. Remove it.
Addresses-Coverity: ("Same on both sides")
Fixes: 12e2b2d4c6 ("drm/amd/display: add dcc programming for dual plane")
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are spelling mistakes in a DC_ERROR message and a comment.
Fix these.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Variable status is redundant, it is being initialized with a value
that is over-written later and this is being returned immediately
after the assignment. Clean up the code by removing status and
just returning the value returned from the call to function
dc->hwss.dmdata_status_done.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dm_dcn_crtc_high_irq() is only used when CONFIG_DRM_AMD_DC_DCN is set.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Since dcn20 and dcn21 are under dcn1 it doesnt make sense to
have it named dcn1.
Change it to "dcn" to make it generic
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCN21 is stable enough to be build by default. So drop the flags.
[How]
Remove them using the unifdef tool. The following commands were executed
in sequence:
$ find -name '*.c' -exec unifdef -m -DCONFIG_DRM_AMD_DC_DCN2_1 -UCONFIG_TRIM_DRM_AMD_DC_DCN2_1 '{}' ';'
$ find -name '*.h' -exec unifdef -m -DCONFIG_DRM_AMD_DC_DCN2_1 -UCONFIG_TRIM_DRM_AMD_DC_DCN2_1 '{}' ';'
In addition:
* Remove from kconfig, and replace any dependencies with DCN1_0.
* Remove from any makefiles.
* Fix and cleanup Renoir definitions in dal_asic_id.h
* Expand DCN1 ifdef to include DCN21 code in the following files:
* clk_mgr/clk_mgr.c: dc_clk_mgr_create()
* core/dc_resources.c: dc_create_resource_pool()
* gpio/hw_factory.c: dal_hw_factory_init()
* gpio/hw_translate.c: dal_hw_translate_init()
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCN2 and DSC are stable enough to be build by default. So drop the flags.
[How]
Remove them using the unifdef tool. The following commands were executed
in sequence:
$ find -name '*.c' -exec unifdef -m -DCONFIG_DRM_AMD_DC_DSC_SUPPORT -DCONFIG_DRM_AMD_DC_DCN2_0 -UCONFIG_TRIM_DRM_AMD_DC_DCN2_0 '{}' ';'
$ find -name '*.h' -exec unifdef -m -DCONFIG_DRM_AMD_DC_DSC_SUPPORT -DCONFIG_DRM_AMD_DC_DCN2_0 -UCONFIG_TRIM_DRM_AMD_DC_DCN2_0 '{}' ';'
In addition:
* Remove from kconfig, and replace any dependencies with DCN1_0.
* Remove from any makefiles.
* Fix and cleanup NV defninitions in dal_asic_id.h
* Expand DCN1 ifdef to include DCN2 code in the following files:
* clk_mgr/clk_mgr.c: dc_clk_mgr_create()
* core/dc_resources.c: dc_create_resource_pool()
* dce/dce_dmcu.c: dcn20_*lock_phy()
* dce/dce_dmcu.c: dcn20_funcs
* dce/dce_dmcu.c: dcn20_dmcu_create()
* gpio/hw_factory.c: dal_hw_factory_init()
* gpio/hw_translate.c: dal_hw_translate_init()
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On DCN hardware, the crtc_high_irq handler makes vupdate_high_irq
handler redundant.
All the vupdate handler does is handle vblank events, and update vrr
for DCE hw (excluding VEGA, more on that later). As far as usermode is
concerned. vstartup happens close enough to vupdate on DCN that it can
be considered the "same". Handling vblank and updating vrr at vstartup
effectively replaces vupdate on DCN.
Vega is a bit special. Like DCN, the VRR registers on Vega are
double-buffered, and swapped at vupdate. But Unlike DCN, it lacks a
vstartup interrupt. This means we can't quite remove the vupdate handler
for it, since delayed user events due to vrr are sent off there.
[How]
Remove registration of vupdate interrupt handler for DCN. Disable
vupdate interrupt if asic family DCN, enable otherwise.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For DCN hardware, the crtc_high_irq handler is assigned to the vstartup
interrupt. This is different from DCE, which has it assigned to vblank
start.
We'd like to send vblank and user events at vstartup because:
* It happens close enough to vupdate - the point of no return for HW.
* It is programmed as lines relative to vblank end - i.e. it is not in
the variable portion when VRR is enabled. We should signal user
events here.
* The pflip interrupt responsible for sending user events today only
fires if the DCH HUBP component is not clock gated. In situations
where planes are disabled - but the CRTC is enabled - user events won't
be sent out, leading to flip done timeouts.
Consequently, this makes vupdate on DCN hardware redundant. It will be
removed in the next change.
[How]
Add a DCN-specific crtc_high_irq handler, and hook it to the VStartup
signal. Inside the DCN handler, we send off user events if the pflip
handler hasn't already done so.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1-Read lttpr caps in 5-bytes
2-Parse caps
3-Validate caps and set lttpr_mode
4-Use hw default timeout when lttpr is disabled.
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The aux timeout value is not default before reading link cap.
Setting it to default when lttpr is not enabled causes some monitor
not to light up.
[How]
Read the aux engine timeout value before setting it to extended.
Set the aux engine timeout to its previous value if no lttpr.
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1-If at least one repeater is present in the link and we are in non
transparent mode, perform clock recovery then channel equalization
with all repeaters one by one before training DPRX.
2-Mark the end of LT with a repeater by setting training pattern 0
at the end of channel equalization with each repeater.
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
1-Grant extended timeout request. Done once after detection
2-Configure lttpr mode based on lttpr support before LT
3-Account for lttpr cap when determining max link settings
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
LTTPR was introduced after DP1.2. Reading LTTPR registers 0xFXXXX
on some DP 1.2 display is causing an unexpected behavior.
[How]
Make sure that we don't read any lttpr registers on 1.2 displays.
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
When reading link, update the procedure as follows:
1-Set aux timeout to extended: 3.2ms
2-Start with reading lttpr caps
3-Determine if lttpr support should be enabled. Reset aux timeout to
400us if no repeater is found.
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
We want to guarantee integer ratio scaling for all scaling modes.
[how]
Treat centered, fullscreen, preserve aspect ratio the same: scale
the view as many times as possible, and fill in the rest with a black
border.
Signed-off-by: Reza Amini <Reza.Amini@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Need it for some OEM I2C devices in Nv10
[how]
Link up code to parse OEM table and expose DC interface
to access the pins
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For debug purpose, we need to check the following hardware status
in DTN log debugfs:
1.dpp & hubp clock enable;
2.crtc blank enable;
3.link phy status;
[How]
Add the upper information in the amdgpu_dm_dtn_log debugfs.
For CRTC blanked status, since DCN2 and greater reports it on the OPP
instead of OTG, we patch it in after calling optc1_read_otg_states.
Ideally, this should be done in the DCN version specific function hooks.
It has been left as a TODO item.
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
System is unable to enter S0i3 due to DISPLAY_OFF_MASK not asserted
in SMU.
[How]
Optimized bandwidth should be called paired and to resolve unplug
display underflow issue, optimize bandwidth after commit streams is
moved to next page flip, in case of S0i3, there is a change for no
flip coming causing display count is 1 in SMU side.
Add optimize bandwidth after commit stream.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
It has been a useful option in debugging GFXOFF and P.State Change issues.
May be required as for platform specific workaround.
[HOW]
Create option in enum dc_debug_options, "disable_vactive_clock_change".
When it is set, dm_dram_clock_change_vactive, will translate into
p_state_change_support: false.
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It is confusing to sinks if we send VSC SDP only on some format. Today we
signal colorimetry format using MSA while in formats like sRGB.
But when we switch to BT2020 we set the bit to ignore MSA colorimetry and
instead use the colorimetry information in the VSC SDP.
But if sink supports signaling of colorimetry via VSC SDP we should always
set the MSA MISC1 bit 6, instead of doing so selectively.
[How]
If sink supports signaling of colorimetry via VSC SDP, and we are sending
the colorimetry info via VSC SDP with packet revision 05h, then always
set MSA MISC1 bit 6.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
If acquire/release DSC resource sequence is affected by a regression,
it can happen that the already-in-use DSC HW block is being wrongly
re-used for a different pipe. The reverse is also possible, i.e.
already-disabled DSC HW block could be disabled from other context.
[how]
Read back the enable state of DSC HW and report an error if duplicate
enable or disable was attempted.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently made a change where disable_output is called using signal_type.
Using actual signal_type when calilng disable_output in power_down_encoders
would make DP to HDMI dongle not light up on boot. As it would have signal_type
SIGNAL_TYPE_DISPLAY_PORT.
[HOW]
Set signal_type to SIGNAL_TYPE_NONE unless it is eDP.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For unknown reason, immediate flip with host VM translation on NV12
surface will underflow on last row of PTE.
[How]
Hack chroma viewport height to make fetch one more row of PTE.
Note that this will cause hubp underflow on all video underlay
cases, but the underflow is not user visible since it is in
blank region.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
V.Active dram clock change workaround need a small modification for DMLv2
to ensure that the dummy p-state check doesn't fail.
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Support for DMUB only depends on support for DC. It doesn't use floating
point so we don't need to guard it by any specific DCN revision.
[How]
Drop the guards and cleanup the newlines around each one.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DC can utilize the DMUB server to send commands to the DMUB but it's
the DM responsibility to pass it the service to use.
[How]
Create the dc_dmub_srv after we finish initializing the dmub_srv.
Cleanup the dc_dmub_srv before destroying the dmub_srv or dc.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DC will use DMUB for command submission and flow control during
initialization.
Register offloading as well as submitting some BIOS commands are part
of the DC internal interface but are guarded behind debug options.
It won't be functional in amdgpu_dm yet since we don't pass the
DMUB service to DC for use.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need DMCUB on Renoir to support DMCU and PHY initialization.
The DMUB service provides a mechanism to load the DMCUB.
[How]
Include the DMUB service in amdgpu_dm.
Frontdoor loading of the DMCUB firmware needs to happen via PSP. To
pass the firmware to PSP we need to hand it off to the firmware list
in the base driver during software initialization.
Most of the DMUB service can technically be initialized at this point
in time, but we don't want to be allocating framebuffer memory for
hardware that doesn't support the DMCUB and in order to check that we
need to be able to read registers - something DM helpers aren't setup
to do in software initialization.
So everything but the service creation itself will get deferred to
hardware initialization.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PSP version format is AB.CD.EF.GH, where CD and GH is the main version.
current psp version check for dmcub loading dmcu check 0x00110029, in
case of some psp version eg: 0x00110227 which main version should be
0x00110027, will result in unexpeceted dmcub loading dmcu FW.
[How]
Add psp version mask 0x00FF00FF for checking version.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The DMUB service is the interface to the DMCUB.
It's required to support Renoir features so it will be enabled and
compiled automatically when the Renoir display engine is enabled via
CONFIG_DRM_AMD_DC_DCN2_1.
DMUB code will initially be guarded by CONFIG_DRM_AMD_DC_DMUB and later
switched to CONFIG_DRM_AMD_DC_DCN2_1 with the config option dropped.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The interface to the DMCUB won't be through DC itself. DC will instead
call into the DMUB interface introduced with a future change.
The CONFIG_DRM_AMD_DC_DMUB defines will still be used for now but will
be dropped at the end of the series.
Since this define was never configurable in the first place this code
wasn't used.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently pointer aconnector is being dereferenced by the call to
to_dm_connector_state before it is being null checked, this could
lead to a null pointer dereference. Fix this by checking that
aconnector is null before dereferencing it.
Addresses-Coverity: ("Dereference before null check")
Reviewed-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Adding encoder atomic check to find vcpi slots for a connector
- Using DRM helper functions to calculate PBN
- Adding connector atomic check to release vcpi slots if connector
loses CRTC
- Calculate PBN and VCPI slots only once during atomic
check and store them on crtc_state to eliminate
redundant calculation
- Call drm_dp_mst_atomic_check to verify validity of MST topology
during state atomic check
v2: squashed previous 3 separate patches, removed DSC PBN calculation,
and added PBN and VCPI slots properties to amdgpu connector
v3:
- moved vcpi_slots and pbn properties to dm_crtc_state and dc_stream_state
- updates stream's vcpi_slots and pbn on commit
- separated patch from the DSC MST series
v4:
- set vcpi_slots and pbn properties to dm_connector_state
- copy porperties from connector state on to crtc state
v5:
- keep the pbn and vcpi values only on connnector state
- added a void pointer to the stream state instead on two ints,
because dc_stream_state is OS agnostic. Pointer points to the
current dm_connector_state.
v6:
- Remove new param from stream
v7:
- Fix error with using max capable bpc
v8:
- squash in fix from Gustavo A. R. Silva
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl3IqJQeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGOiUH+gOEDwid5OODaFAd
CggXugdFIlBZefKqGVNW5sjgX8pxFWHXuEMC8iNb6QXtQZdFrI6LFf9hhUDmzQtm
6y1LPxxEiTZjObMEsBNylb7tyzgujFHcAlp0Zro3w/HLCqmYTSP3FF46i2u6KZfL
XhkpM4X7R7qxlfpdhlfESv/ElRGocZe6SwXfC7pcPo5flFcmkdu9ijqhNd/6CZ/h
Nf9rTsD/wEDVUelFbgVN+LJzlaB0tsyc4Zbof07n8OsFZjhdEOop8gfM/kTBLcyY
6bh66SfDScdsNnC/l8csbPjSZRx+i+nQs67DyhGNnsSAFgHBZdC4Tb/2mDCwhCLR
dUvuYZc=
=1N6F
-----END PGP SIGNATURE-----
Merge v5.4-rc7 into drm-next
We have the i915 security fixes to backmerge, but first
let's clear the decks for other drivers to avoid a bigger
mess.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Use the ddc pointer provided by the generic connector.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ <40293fa4e619d1d1af213a076b1d03440e50c56c.1566845537.git.andrzej.p@collabora.com
This reverts commit 967a3b85ba.
Reason for revert: Root cause of this issue is found. The workaround is not needed anymore.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
