There are some differences between the schematics and the official firmware
DTS [1]. So based on these additional information the following has been
changed:
* use consistent "CAM_GPIO1" for camera LED
* use consistent "CAM_GPIO0" for camera shutdown
* add "USB_LIMIT" for USB current limit (0=600mA, 1=1200mA)
[1] - https://github.com/raspberrypi/firmware/blob/master/extra/dt-blob.dts
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The idea is to give useful names to GPIO lines that an implementer
will be using from userspace, e.g. for maker type projects. These are
user-visible using tools/gpio/lsgpio.c
v2: Major rewrite by anholt: Flatten each GPIO line to a line in the
file for better diffing, prefix all expansion header pins with
"P<number>" or "P5HEADER_P<number>" and drop the mostly-unused
GPIO_GEN<smallnumber> names in favor of GPIO<socgpionumber>, fix
extra '[]' on a couple of lines, fix locations of SD_CARD_DETECT,
CAM_GPIO and STATUS_LED, fix HDMI_HPD polarities, rewrite A+ using
unreleased schematics.
v3: More changes by anholt: Drop P<number> / P5HEADER<number>
prefixes. I had been skeptical about adding them, and was
convinced to drop them by Gottfried (who probably has more
experience with GPIOs in educational contexts than the rest of
us). Also drop [] brackets for "is pinmuxed", which didn't seem
to clarify, and were ambiguous for things like the SPI_*-labeled
pins which may or may not actually be pinmuxed to SPI.
v4: Rename B+'s SDA0/SCL0 to match the other boards, despite the
naming on its schematic.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
As the alt3 group has no pins left drop it from &gpio.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
In case dr_mode isn't passed via DT, the dwc2 defaults to OTG mode.
But all Raspberry Pi boards here are designed only for host mode.
So fix this issue by providing a dtsi file which set the dr_mode
to host.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The hub and the ethernet in its port 1 are hardwired on the board.
Compared to the adapters that can be plugged into the USB ports, this
one has no serial EEPROM to store its MAC. Nevertheless, the Raspberry Pi
has the MAC address for this adapter in its ROM, accessible from its
firmware.
U-Boot can read out the address and set the local-mac-address property of the
node with "ethernet" alias. Let's add the node so that U-Boot can do its
business.
Model B rev2 and Model B+ entries were verified by me, the hierarchy and
pid/vid pair for the Version 2 was provided by Peter Chen. Original
Model B is a blind shot, though very likely correct.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
For Raspberry Pi 2, we want to use the same general pin assignment
bits, but need to use bcm2836.dtsi for the CPU instead.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch converts all bcm2835 dts and dtsi files to use the pinctrl
header file.
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The model B and B+ differ in the GPIO lines for ACT and PWR leds, and the
I2S interface.
Signed-off-by: Matthias Klein <matthias.klein@linux.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
