The target is not ready to accept addkey commands until the connect
event has been delivered, so delay these operations for the initial GTK.
In addition, properly set interface connected and mark netdev ready when
the AP mode setup has been completed.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Need to use correct length field for association request frame and
parse the IEs to find WPA/WPS/RSN IE. In addition, copying of the
IE better make sure it fits in into the buffer to avoid buffer
overflows.
In addition, add the (Re)AssocReq IEs to the cfg80211 new station
event for user space.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use cfg80211 add/del_beacon callbacks for starting/stopping AP mode and
set_beacon to update AP configuration (mainly, to update Beacon and
Probe Response IEs).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It would be at <dbgfs_root>/ieee80211/phyX/ath6kl/credit_dist_stats.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It would be at <debugfs_root>/ieee80211/phyX/ath6kl/tgt_stats.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Just initial debugfs changes. The debugfs directory would
be created at <debugfs_root>/ieee80211/phyX/ath6kl.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Current tx scatter gather implementation rolls back the entire
scatter setup in case of a failure in setting up just one packet
into the bundle. Instead of dopping the whole scatter setup,
send the packets available just before the failure one using
scatter gather I/O.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Patch "ath6kl: Fix buffer alignment for scatter-gather write" does
memmove for a length (scat_req->scat_list[i].len) which is not the
actual length of data that is suppossed to be moved. The right
lengh is packet->act_len + HTC_HDR_LENGTH. Using wrong length
for data move during buffer alignment causes system freeze after
the following WARN_ON and sometimes target assert.
WARNING: at drivers/net/wireless/ath/ath6kl/main.c:771 ath6k_credit_distribute+0x196/0x1a0
[<ffffffffa051cf5f>] ath6kl_htc_rxmsg_pending_handler+0x83f/0xe00 [ath6kl]
[<ffffffff8104a743>] ? __wake_up+0x53/0x70
[<ffffffffa0518b18>] ath6kldev_intr_bh_handler+0x188/0x650 [ath6kl]
[<ffffffffa052d316>] ath6kl_sdio_irq_handler+0x36/0x80 [ath6kl]
[<ffffffff81492b3c>] sdio_irq_thread+0xfc/0x360
[<ffffffff81051c52>] ? default_wake_function+0x12/0x20
[<ffffffff81492a40>] ? sdio_claim_irq+0x220/0x220
[<ffffffff81080c36>] kthread+0x96/0xa0
[<ffffffff815b9fb4>] kernel_thread_helper+0x4/0x10
[<ffffffff81080ba0>] ? kthread_worker_fn+0x190/0x190
[<ffffffff815b9fb0>] ? gs_change+0x13/0x13
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For now this is implemented so that if host supports power is kept in
the chip. If that's not supported, an error is returned and sdio stack
will remove the device during suspend.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For non-scatter buffers, there is already a bounce buffer which
takes care of alignment. This patch is influenced by a rough patch of
Kalle.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This fixes AMSDU rx, otherwise it fails with the following warnings.
"802.3 AMSDU frame bound check failed"
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This lock is intended to protect stats there, not neccessary to
hold it beyond that.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In some random cases, the firmware is sending two disconnect event to
the host. In the current model, both diconnect events are passed to
cfg80211 without checking local sme state machine, which is screwing
cfg80211 layer state.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Connect event handler function is always reporting BSS info
to CFG80211 layer first and then followed by connect event is passed.
Before these steps, BSS presence is retrieved from CFG80211 layer,
but it is not used. Hence, removing that part.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There is no point in generating a bogus Beacon frame for
cfg80211_inform_bss_frame when cfg80211_inform_bss can be used
instead.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
this comment refers to some code that was removed.
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With sequence number and buffer allocation deferred to when they're needed
for the first time, it becomes much easier to start dropping packets from
the tid queue if necessary, e.g. when latency suddenly increases. This can
lead to some future improvements in buffer management for better latency.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is only necessary for BAW tracking and moving it to the ath_buf
makes it easier to add further improvements, such as deferring
seqno allocation in the aggregation path.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a sk_buff_head instead containing skbs instead of a list_head
containing ath_bufs. This makes it easier to decouple the aggregation
code from the ath_buf struct
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Changing the return type and removing the unused argument from
ath_printk reduces code size.
Add an __always_unused struct ath_common * to the macros
that call ath_printk to avoid unused variable warnings.
$ size drivers/net/wireless/ath/built-in.o*
text data bss dec hex filename
1159859 16235 212000 1388094 152e3e drivers/net/wireless/ath/built-in.o.new
1164175 16235 212032 1392442 153f3a drivers/net/wireless/ath/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The return value is never used so make it void.
Reduces object size a tiny bit.
$ size drivers/net/wireless/ath/built-in.o*
text data bss dec hex filename
1164175 16235 212032 1392442 153f3a drivers/net/wireless/ath/built-in.o.new
1164819 16235 212032 1393086 1541be drivers/net/wireless/ath/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit c302b2c959 ("wl12xx: Use a single
fw for both STA and AP roles") changed the name of the firmware name
definition, breaking the build of wl12xx/sdio_test.c.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Swatch reports the following warning for main.c:
CHECK drivers/net/wireless/b43/main.c
drivers/net/wireless/b43/main.c +4115 b43_wireless_core_stop(7) warn: variable dereferenced before check 'dev'
After analysis, this is not a bug, but a false warning. Nonetheless,
a cleanup is in order to prevent some future janitor proposing
the wrong fix, as I did in my original patch.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch keep track of number of samples that includes
DMA debugs registers, PCU observe, CR, channel noise,
cycle conters, noisefloor history buffer and last N number
of tx and rx descriptor status. These samples are grouped
in table manner which dumping in debgufs.
Debugfs file location:
<debugfs_mnt>/ieee80211/phy#/ath9k/samples
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The recent commit "ath9k: Send legacy rated frames as unaggregated"
introduced a check to ensure that packets with non-MCS rates set in
the rate series will not be aggregated. However, it failed to check
if the rate series is valid before testing the flags, thus breaking
aggregation for normal MCS-only packets if the last series is unset.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For AR9287 v1.3+ chips, MAC runs at 117MHz. But the initvals
IFS parameters are loaded based on 44/88MHz clockrate. So
eifs/usec from ini should not be used for AR9287 v1.3+.
The mentioned values are tested on 2 chain HT40 mode.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initialize 9us slot time as that is what is used mostly
(for non-ERP cases) and also to be in sync with initvals.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It was tested on three BCM4331 devices, code has been written from MMIO
dumps only, but seems to be quite stable.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When 64-bit DMA was first used, there were problems with the
BCM4311 (14e4:4311). The problem was "fixed" by using the GFP_DMA
flag in the allocation of coherent ring descriptor memory.
The original problem is now believed to have been due to bugs in
the 64-bit DMA implementation in the rest of the kernel, and that
those bugs have been fixed. Accordingly, the requirement for the
descriptors to be in the DMA zone is relaxed.
Bounce buffers are left in the DMA zone.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Michael Buesch <m@bues.ch>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since commit e0626e38 (spi: prefix modalias with "spi:"),
the spi modalias is prefixed with "spi:".
This patch adds "spi:" prefix for modalias of stlc45xx.
Also move it to be group with other modalias.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-By: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to implement support for GO powersave on
the P2P client side, the ucode needs to know what
GO we're trying to authenticate/associate with,
it needs to have a station entry and the BSSID in
the RXON set.
Implement the new mac80211 callbacks to give this
data to the device.
Since this is also useful for the device when a
normal connection is established, also program it
with the information in that case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This finalizes the move of the data path to the transport layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
priv->mac80211_registered and priv->hw needed to move to shared.
stop_queue API was added in order to allow the upper layer to stop
the SW queues for regulatory purposes.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This one is really transport related.
==== moves Stanislaw's code to BSD area ====
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This one is really transport related.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
