For systems which do not have a jack detection feature allow some debounce
to be specified before we perform accessory identification, improving
robustness without impacting button detection responsiveness.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is loopback control within the audio interfaces, provide control of
this as there are some obscure scenarios where this could be used in
production.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The DSPs IRQ should be a wake source as several of the possible
algorithms may run whilst the AP is asleepi and require to wake the AP
to push or pull more data, such as compressed playback.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Provide a bit of debounce to handle pathological cases with slow input
better by allowing the microphone detection to run for a bit longer.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The array 'drc_cfg' of size 3 may use index value -22 (EINVAL)
The array 'retune_mobile_cfg' of size 3 may use index value -22 (EINVAL)
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rename `dirty' to `set' as it is a bit more descriptive. A set
control is any control that has been set by the user. We need to ensure
that everytime we boot the DSP we sync out any controls that were
set.
We could at some point start keeping track of the default values of
the controls to suppress some of the device I/O.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
During recent refactoring the code to report removal when MICDET reports
an absent microphone was removed, causing problems for systems which rely
solely on the MICDET for this functionality. Restore it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Define ab8500 codec operations structure on its own rather than inline
with snd_soc_dai_drivers to clean up the code and make the style
coherent with other codec drivers.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds a ASoC CODEC driver for the SSM2516. The SSM2516 is a stereo
Class-D audio amplifier with an I2S interface for audio in and a built-in
dynamic range control processor.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The mask should define the bits to change in the register, not the
bits to preserve.
This fixes the inadvertent changes of the "Headphone Analog Gain"
value during mute/unmute.
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
DFBM-CS320 is only one of bluetooth modules using CSR bluetooth chips,
we don't want everyone to have a seperate codec driver. anyway, the
feature of Bluetooth SCO is same on all platforms, so this patch
makes the DFBM-CS320 driver become a common BT SCO link driver.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Replace hard coded rx slot numbers from ab8500_codec_set_dai_tdm_slot
using the ones requested by the machine driver in rx_mask instead.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Replace hard-coded tx slot numbers from ab8500_codec_set_dai_tdm_slot
using the ones requested by the machine driver in tx_mask instead.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add callback to initialise the speaker in the core following the recent
changes to handling of integration with the thermal interrupts.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
On WM8958 and WM1811A separate control of the LRCLK inversion bit is
available for the DAC and ADC LRCLKs which for compatibility reasons is
done in a new register bit.
Since writes to each scheme have no effect on parts using the other just
always write to both for simplicity.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Samreen Nilofer <samreen.nilofer@intel.com>
request_threaded_irq() rejects calls which both do not specify a handler
(indicating that the primary IRQ handler should be used) and do not set
IRQF_ONESHOT because the combination is unsafe with level-triggered
interrupts. It is safe in this case, though, since max98090 IRQs are
edge-triggered and the interrupts aren't ACK'ed until the codec's IRQ
status register is read. Because of this, an IRQF_ONESHOT interrupt
doesn't really make a difference, but request one anyway in order to make
request_threaded_irq() happy.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The max98090 driver currently treats the digital mic enable as a supply
on the record path, causing the digital mic enable to always be turned on
when attempting to record. This is incorrect, however, since the digital
mic enable is also a mux control where 0 selects the ADC output as input
to the record-path DSP and 1 selects the digital mic. This patch adds
a virtual DMIC mux to the reocrd path so that we can switch between the
ADC and the digital mic for recording.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Later WM8994 devices support an enhanced accuracy FLL divisor mode called
EFS which allows more precise selection of fractional source to output
ratios. Support this on relevant devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
According to the AB8500 user manual AD to Slot register multiplexer
accept values from 0 to 15 where:
0 to 7 corresponds to AD_OUTx slots
8 to 11 corresponds to zero output
12 to 15 sets the output in tristate mode
Update enum_ad_to_slot_map array to reflect this definition.
This also allows alsamixer to properly display the default
configuration, as all controls are set to tristate (=12) at reset.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
