Merge to get the wil6210 changes that a cfg80211 change needs.
A conflict in drivers/net/wireless/ath/ath9k/init.c was just
whitespace changes.
Also fix a semantic conflict due to cw1200 using WoWLAN which
I had modified in my tree.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move message to debug mode to reduce log spam under heavy tx (iperf) load.
This message prints in ht debug mode only:
brcms_c_ampdu_dotxstatus_complete: Pkt tx suppressed, illegal channel
possibly 153
Signed-off-by: John Greene <jogreene@redhat.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ANI state can be maintained globally instead of per-channel.
This reduces memory usage and since default values are used
during a scan run, per-channel state is not required.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The check "enable_ani" is not required since it is always
set to true and the logic for disabling/enabling ANI via
debugfs is done at a higher layer.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The only card with which WoW has been tested and verified is
AR9462. Do not enable it for all cards since WoW is really quirky
and needs to be tested properly with each chip.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Process and update the internal RSSI average, which
is used by ANI, after verifying that the received
frame has valid rate information.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pci_enable_device() will set device power state to D0,
so it's no need to do it again in ipw2100_pci_init_one().
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My previous patch just moved the file, but it also needed to be renamed
to conform to proper conventions.
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on discussions with And Bergmann, this patch changes the SDIO
platform code to default to supporting the Sagrad devices, allowing for
it to be overridden in board setup code. This renders the cw1200_sagrad
module suplerflous, so it is now removed.
It also moves the documentation that was in the cw1200_sagrad source to
the platform header.
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The only advantage of 'struct resource' is that it lets us assign names
as part of the platform data. Unfortunately since we are using platform
data, we are already limited to a single instance of each driver,
rendering this moot.
So, replace the struct resources with ints, resulting in cleaner code.
This was based on a suggestion from Arnd Bergmann.
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This avoids problems when building on SPARC targets due to the driver
calling the bus abstraction layer 'sbus'. Not that any SBUS-sporting
SPARC targets are likely to have an SDIO controller, but this is the
correct thing to do.
See http://kisskb.ellerman.id.au/kisskb/buildresult/8846508/
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need to take up the space for devices that don't
support WoWLAN, and most drivers can even make the support
data static const (except where it's modified at runtime.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sg_sz and buf_sz are initialized and used in a mutual exclusive way.
However, some versions of gcc are not smart enough to see this:
drivers/net/wireless/ath/ath6kl/sdio.c: In function ‘ath6kl_sdio_alloc_prep_scat_req’:
drivers/net/wireless/ath/ath6kl/sdio.c:338: warning: ‘sg_sz’ may be used uninitialized in this function
Unify the sg_sz and buf_sz variables into a single size variable to kill
the compiler warning.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
cfg80211 suspend/resume callbacks are not yet implemented
for AR6004 USB. Introduce dummy handlers for these to avoid
NULL pointer dereference.
Cc: Sivanesan Rajapupathi <c_srajap@qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rename USB driver's suspend/resume/reset_resume callbacks
with 'pm' prefix. This is necessary to differentiate it from
cfg80211/hif suspend/resume/reset_resume callbacks.
Cc: Sivanesan Rajapupathi <c_srajap@qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There is no point to check firmware ABI version when the driver
fails to wait for WMI_READY event during the boot time.
For such failures, the driver should assume the firmware is not
booted and start doing cleanup.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This reverts commit e3ee68b7b0.
This wasn't intended to be included here, my mistake. I
accidentally merged a mac80211 fixes tree here that had
this change, when it wasn't even intended to be there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit eebfc9394e.
This wasn't intended to be included here, my mistake. I
accidentally merged a mac80211 fixes tree here that had
this change, when it wasn't even intended to be there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This removes an open coded simple_open() function and
replaces file operations references to the function
with simple_open() instead.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Intel's 0-day kernel build tester caught this build failure. This patch
properly wraps everything that depends on CONFIG_PM.
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch make use of STBC flag in DMA RX descriptor.
Only devices after ar9280 can provide this information.
If card support it we will set HAVE_STBC flag, to show
clint programm thet STBC is supported but not received.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
some flags used only outside of ath9k - In this case we can use
"enum mac80211_rx_flags" and pass it upstream without extra
conversation.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For testing the D3 (WoWLAN) firmware, it is useful to be able
to run the firmware with instrumentation while the host isn't
sleeping and can poke at the firmware debug logging etc.
Implement this by a debugfs file. When the file is opened the
D3 firmware is loaded and all regular commands are blocked.
While the file is being read, poll the firmware's PME status
flag and report EOF once it changes to non-zero. When it is
closed, do (most of) the resume processing. This lets a user
just "cat" the file. Pressing Ctrl-C to kill the cat process
will resume the firwmare as though the platform resumed for
non-wireless reason and when the firmware wants to wake up
reading from the file automatically completes.
Unlike in real suspend, only disable interrupts and don't
reset the TX/RX hardware while in the test mode. This is a
workaround for some interrupt problems that happen only when
the PCIe link isn't fully reset (presumably by changing the
PCI config space registers which the core PCI code does.)
Note that while regular operations are blocked from sending
commands to the firmware, they could still be made and cause
strange mac80211 issues. Therefore, while using this testing
feature you need to be careful to not try to disconnect, roam
or similar, and will see warnings for such attempts.
Als note that this requires an upcoming firmware change to
tell the driver the location of the PME status flag in SRAM.
D3 test will fail if the firmware doesn't report the pointer.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make the commenting style consistent with networking block comment
style as suggested by checkpatch.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
module_spi_driver() eliminates some boiler plate and makes code
simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If any bins from the training data are skipped (i != max_index), the
calculated compensation curve gets distorted, and the signal will be
wildly overamplified. This may be the cause of the reported hardware
damage that was caused by PA predistortion (because of which PAPRD was
disabled by default).
When calculating the x_est, Y, theta values, the use of max_index and i
was reversed. i points to the bin index whereas max_index refers to the
index of the calculated arrays.
Note that PA predistortion is still disabled, it will be re-enabled
after it has been properly validated.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware supports periodic keep alive and beacon monitoring,
so advertise connection monitor offload capability by setting
IEEE80211_HW_CONNECTION_MONITOR flag. Implement missed beacons
notification handler. Call ieee80211_beacon_loss in case of
missed beacons, so AP probing by mac80211 can be triggered.
Signed-off-by: Hila Gonen <hila.gonen@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If skip over DTIMs is enabled the driver can specify number of DTIMs
to skip. This parameter in host-device API implies number of DTIM
periods to skip. For example, to skip one DTIM means sleep over two
DTIM periods. Change semantics accordingly. Change this parameter's
default value.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to avoid NIC destruction due to high temperature,
CT kill will power down the NIC.
To avoid this, thermal throttling will decrease throughput
to prevent the NIC from reaching the temperature at which
CT kill is performed.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
