Use new display drivers for AM3517EVM board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Note: the management of LCD GPIOs is unclear. They were originally muxed
as inputs, and LCD_PANEL_PWR was labelled as "dvi enable".
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Use new display drivers for Zoom board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Use new display drivers for OMAP3 Pandora board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Use new display drivers for OMAP3EVM board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Use new display drivers for 3430SDP board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Use new display drivers for H4 board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Use new display drivers for cm-t35 board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Use new display drivers for igep0020 board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Use new display drivers for OMAP3 Stalker board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Use new display drivers for LDP board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Use new display drivers for 2430SDP board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Use new display drivers for devkit8000 board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Use the new display drivers for Beagleboard.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Use the new display drivers for RX51 board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Tony Lindgren <tony@atomide.com>
Use the new display drivers for OMAP3 Overo board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Note that the LCD add-on boards for lcd43 and lcd35 use the same GPIOs
for the panels. This means that both panel devices cannot be probed at
the same time.
DT will handle this correctly, i.e. the DT data will contain the panel
device only for the add-on board that is attached. However, for the
board file we need a hackish solution: We parse the kernel boot command
line, and see whether lcd43 or lcd35 is set as a default display, and
add the given one. Or, if neither is given, default to lcd43.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
4430SDP board has an option for a PicoDLP mini-projector. PicoDLP cannot
be used at the same time as the second LCD, and there are GPIOs that
need to be set/unset when changing the used display.
Managing that kind of board specific setup is not simple without board
file callbacks. As only some 4430SDP boards actually have the PicoDLP
installed, and 4430SDP boards are not that common in the first place,
let's remove PicoDLP data from the board file.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Use the new display drivers for OMAP4 Panda and OMAP4 SDP boards.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
This is no longer needed as omap4 is now booted using device tree.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
This patch adds alwon powerdomain support for TI81XX, which is required
for stable functioning of a big number of TI81XX subsystems.
Signed-off-by: Aida Mynzhasova <aida.mynzhasova@skitlab.ru>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On OMAP4 we have clk_set_rate()s being done for a few
DPLL clock nodes, as part of the clock init code, since
the bootloaders no longer locks these DPLLs.
So we have a clk_set_rate() done for a ABE DPLL node (which
inturn locks it) followed by a clk_set_rate() for the USB DPLL.
With USB DPLL being in bypass, we have this parent->child
relationship thats formed while the clocks get registered.
dpll_abe_ck
|
V
dpll_abe_x2_ck
|
V
dpll_abe_m3x2_ck
|
V
usb_hs_clk_div_ck
|
V
dpll_usb_ck
This is because usb_hs_clk_div_ck is bypass clock for dpll_usb_ck.
So with this parent->child relationship in place, a clk_set_rate()
on ABE DPLL results eventually in a clk_set_rate() call on USB DPLL,
because CCF does a clk_change_rate() (as part of clk_set_rate()) on
all downstream clocks resulting from a rate change on the top clock.
So its important that we lock USB DPLL before we lock ABE DPLL.
Without which we see these error logs at boot.
[These error logs will not be seen if using a bootloader that locks
USB DPLL]
[ 0.000000] clock: dpll_usb_ck failed transition to 'locked'
[ 0.000000] Division by zero in kernel.
[ 0.000000] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.10.0-03445-gfb2af00-dirty #7
[ 0.000000] [<c001bfe8>] (unwind_backtrace+0x0/0xf4) from [<c001868c>] (show_stack+0x10/0x14)
[ 0.000000] [<c001868c>] (show_stack+0x10/0x14) from [<c02deb28>] (Ldiv0+0x8/0x10)
[ 0.000000] [<c02deb28>] (Ldiv0+0x8/0x10) from [<c0477030>] (clk_divider_set_rate+0x10/0x114)
[ 0.000000] [<c0477030>] (clk_divider_set_rate+0x10/0x114) from [<c0476ef4>] (clk_change_rate+0x38/0xb8)
[ 0.000000] [<c0476ef4>] (clk_change_rate+0x38/0xb8) from [<c0476f5c>] (clk_change_rate+0xa0/0xb8)
[ 0.000000] Division by zero in kernel.
[ 0.000000] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.10.0-03445-gfb2af00-dirty #7
[ 0.000000] [<c001bfe8>] (unwind_backtrace+0x0/0xf4) from [<c001868c>] (show_stack+0x10/0x14)
[ 0.000000] [<c001868c>] (show_stack+0x10/0x14) from [<c02deb28>] (Ldiv0+0x8/0x10)
[ 0.000000] [<c02deb28>] (Ldiv0+0x8/0x10) from [<c0477030>] (clk_divider_set_rate+0x10/0x114)
[ 0.000000] [<c0477030>] (clk_divider_set_rate+0x10/0x114) from [<c0476ef4>] (clk_change_rate+0x38/0xb8)
[ 0.000000] [<c0476ef4>] (clk_change_rate+0x38/0xb8) from [<c0476f5c>] (clk_change_rate+0xa0/0xb8)
[ 0.000000] Division by zero in kernel.
[ 0.000000] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.10.0-03445-gfb2af00-dirty #7
[ 0.000000] [<c001bfe8>] (unwind_backtrace+0x0/0xf4) from [<c001868c>] (show_stack+0x10/0x14)
[ 0.000000] [<c001868c>] (show_stack+0x10/0x14) from [<c02deb28>] (Ldiv0+0x8/0x10)
[ 0.000000] [<c02deb28>] (Ldiv0+0x8/0x10) from [<c0477030>] (clk_divider_set_rate+0x10/0x114)
[ 0.000000] [<c0477030>] (clk_divider_set_rate+0x10/0x114) from [<c0476ef4>] (clk_change_rate+0x38/0xb8)
[ 0.000000] [<c0476ef4>] (clk_change_rate+0x38/0xb8) from [<c0476f5c>] (clk_change_rate+0xa0/0xb8)
[ 0.000000] Division by zero in kernel.
[ 0.000000] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.10.0-03445-gfb2af00-dirty #7
[ 0.000000] [<c001bfe8>] (unwind_backtrace+0x0/0xf4) from [<c001868c>] (show_stack+0x10/0x14)
[ 0.000000] [<c001868c>] (show_stack+0x10/0x14) from [<c02deb28>] (Ldiv0+0x8/0x10)
[ 0.000000] [<c02deb28>] (Ldiv0+0x8/0x10) from [<c0477030>] (clk_divider_set_rate+0x10/0x114)
[ 0.000000] [<c0477030>] (clk_divider_set_rate+0x10/0x114) from [<c0476ef4>] (clk_change_rate+0x38/0xb8)
[ 0.000000] [<c0476ef4>] (clk_change_rate+0x38/0xb8) from [<c0476f5c>] (clk_change_rate+0xa0/0xb8)
[ 0.000000] Division by zero in kernel.
[ 0.000000] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.10.0-03445-gfb2af00-dirty #7
[ 0.000000] [<c001bfe8>] (unwind_backtrace+0x0/0xf4) from [<c001868c>] (show_stack+0x10/0x14)
[ 0.000000] [<c001868c>] (show_stack+0x10/0x14) from [<c02deb28>] (Ldiv0+0x8/0x10)
[ 0.000000] [<c02deb28>] (Ldiv0+0x8/0x10) from [<c0477030>] (clk_divider_set_rate+0x10/0x114)
[ 0.000000] [<c0477030>] (clk_divider_set_rate+0x10/0x114) from [<c0476ef4>] (clk_change_rate+0x38/0xb8)
[ 0.000000] [<c0476ef4>] (clk_change_rate+0x38/0xb8) from [<c0476f5c>] (clk_change_rate+0xa0/0xb8)
[ 0.000000] Division by zero in kernel.
[ 0.000000] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.10.0-03445-gfb2af00-dirty #7
[ 0.000000] [<c001bfe8>] (unwind_backtrace+0x0/0xf4) from [<c001868c>] (show_stack+0x10/0x14)
[ 0.000000] [<c001868c>] (show_stack+0x10/0x14) from [<c02deb28>] (Ldiv0+0x8/0x10)
[ 0.000000] [<c02deb28>] (Ldiv0+0x8/0x10) from [<c0477030>] (clk_divider_set_rate+0x10/0x114)
[ 0.000000] [<c0477030>] (clk_divider_set_rate+0x10/0x114) from [<c0476ef4>] (clk_change_rate+0x38/0xb8)
[ 0.000000] [<c0476ef4>] (clk_change_rate+0x38/0xb8) from [<c0476f5c>] (clk_change_rate+0xa0/0xb8)
[ 0.000000] clock: trace_clk_div_ck: could not find divisor for target rate 0 for parent pmd_trace_clk_mux_ck
[ 0.000000] Division by zero in kernel.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In the original hwmod data file, DebugSS entry was disabled,
since we didn't (and do not) have SW to control it.
This patch enables it back with right data, so that it can be
controlled by different ways; and the suggested method it to
have modular driver for debugSS as well.
Refer to the link for more discussion on handling of debugSS -
https://patchwork.kernel.org/patch/2212111/
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Currently, whenever we idle a device _idle_sysc() is called and writes to the
devices SYSCONFIG register to set the idle mode. A lot devices are using the
smart-idle mode and so the write to the SYSCONFIG register is programming the
same value that is already stored in the register.
Writes to the devices SYSCONFIG register can be slow, for example, writing to
the DMTIMER SYSCONFIG register takes 3 interface clock cycles and 3 functional
clock cycles. If the DMTIMER is using the slow 32kHz functional clock this can
take ~100us.
Furthermore, during boot on an OMAP4430 panda board, I see that there are 100
calls to _idle_sysc(), however, only 3 out of the 100 calls actually write
the SYSCONFIG register with a new value.
Therefore, to avoid unnecessary writes to device SYSCONFIG registers when
idling the device, only write the value if the value has changed. It should be
safe to do this on idle as the context of the register will never be lost while
the device is active.
Verified that suspend, CORE off and retention states are working with this
change on OMAP3430 Beagle board.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: updated to apply]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The omap44xx_restart used on omap4 and omap5 devices can be reused
on dra7 devices as well. The device instance however is different
across omap5 and dra7 as compared to omap4. So fix this for omap5
as well as dra7.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
DRA7 belongs to the omap4plus devices which reuse the omap4_pwrdm_operations
ops for powerdomain control. DRA7 however has no VC/VP while all the
earlier omap4plus devices did.
So use the .pwrdm_has_voltdm() ops to pass this info on to the core.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the data file to describe all power domains inside the DRA7XX SoC.
Signed-off-by: Ambresh K <ambresh@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: added generation notation to comments]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the data file to describe all clock domains inside the DRA7XX SoC
Signed-off-by: Ambresh K <ambresh@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: added generation notation to comments]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the PRCM MPU registers for DRA7XX platforms
Signed-off-by: Ambresh K <ambresh@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: added generation notation to comments]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This header contains minimal regbits that are currently used in code.
This header has traditionally been autogenerated on OMAP4+ devices but
the autogenerated contents are largely (95%) unused and hence to reduce
unsued data in the kernel this header has been cut down (from the autogen
output) to whatever is currently needed. This is done by running a cleanup
script on top of the existing autogen script.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Ambresh K <ambresh@ti.com>
[paul@pwsan.com: added generation notation in the comments]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the new defines for DRA7XX CM registers.
Signed-off-by: Ambresh K <ambresh@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: added generation notation in comments]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the new defines for DRA7xx prm module registers.
Signed-off-by: Ambresh K <ambresh@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: added generation notation in the comments]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Pull ARM SoC fixes from Olof Johansson:
"A handful of fixes for 3.11 are still trickling in. These are:
- A couple of fixes for older OMAP platforms
- Another few fixes for at91 (lateish due to European summer
vacations)
- A late-found problem with USB on Tegra, fix is to keep VBUS
regulator on at all times
- One fix for Exynos 5440 dealing with CPU detection
- One MAINTAINERS update"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: tegra: always enable USB VBUS regulators
ARM: davinci: nand: specify ecc strength
ARM: OMAP: rx51: change musb mode to OTG
ARM: OMAP2: fix musb usage for n8x0
MAINTAINERS: Update email address for Benoit Cousson
ARM: at91/DT: fix at91sam9n12ek memory node
ARM: at91: add missing uart clocks DT entries
ARM: SAMSUNG: fix to support for missing cpu specific map_io
ARM: at91/DT: at91sam9x5ek: fix USB host property to enable port C
'gpmc_irq_start' is mostly used as 'int', and for a variable, do not
suggest to only use 'unsigned' as its type, so use 'int' instead of
'unsigned' for variable 'gpmc_irq_start'.
Also it will fix the related issue (dummy the real world failure):
arch/arm/mach-omap2/gpmc.c:728:2: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The denominator should be load from INCREMENTOR_DENUMERATOR_RELOAD_OFFSET
rather than INCREMENTER_NUMERATOR_OFFSET.
This is more likely a typo, since INCREMENTER_DENUMERATOR_RELOAD[23:17] is
reserved. It seems that it won't make much trouble without this fix, because
the useful [11:0] bits are mask and set the right value. Anyway, reading
from a right address is better choice.
Signed-off-by: Chen Baozi <baozich@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently the cold reset was triggered. It happened due to oposite offsets
of cold/warm flags in PRM_RSTST and PRM_RSTCTRL registers.
Signed-off-by: Matus Ujhelyi <ujhelyi.m@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
McPDM and DMIC only available on OMAP4/5 which no longer boots in legacy
mode.
The code to create the devices in legacy mode can be removed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the hwmod data for the mailbox IP in OMAP5 SoC.
This is needed to be able to enable the OMAP mailbox
support for OMAP5.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
From Tony Lindgren:
USB nop phy rename via Felipe Balbi <balbi@ti.com>:
Here's a pull request of one patch to avoid conflicts during the merge
window.
* tag 'omap-for-v3.12/usb-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
usb: phy: rename nop_usb_xceiv => usb_phy_gen_xceiv
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Peripheral-only mode got broken in v3.11-rc1 because of unknown reasons.
Change the mode to OTG, in practice that should work equally well even
when/if the regression gets fixed.
Note that the peripheral-only regression is a separate patch, this change
is still correct as the role is handled by hardware.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit b7e2e75a8c ("usb: gadget: drop unused USB_GADGET_MUSB_HDRC")
dropped a config symbol that was unused by the musb core, but it turns
out that board support code still had references to it.
As the core now handles both dual role and host-only modes, we can just
pass MUSB_OTG as mode from board files.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
From Tomasz Figa:
Here is the Samsung PWM cleanup series. Particular patches of the series
involve following modifications:
- fixing up few things in samsung_pwm_timer clocksource driver,
- moving remaining Samsung platforms to the new clocksource driver,
- removing old clocksource driver,
- adding new multiplatform- and DT-aware PWM driver,
- moving all Samsung platforms to use the new PWM driver,
- removing old PWM driver,
- removing all PWM-related code that is not used anymore.
* tag 'v3.12-pwm-cleanup-for-olof' of git://github.com/tom3q/linux: (684 commits)
ARM: SAMSUNG: Remove plat/regs-timer.h header
ARM: SAMSUNG: Remove remaining uses of plat/regs-timer.h header
ARM: SAMSUNG: Remove pwm-clock infrastructure
ARM: SAMSUNG: Remove old PWM timer platform devices
pwm: Remove superseded pwm-samsung-legacy driver
ARM: SAMSUNG: Modify board files to use new PWM platform device
ARM: SAMSUNG: Rework private data handling in dev-backlight
pwm: Add new pwm-samsung driver
pwm: samsung: Rename to pwm-samsung-legacy
ARM: SAMSUNG: Remove unused PWM timer IRQ chip code
ARM: SAMSUNG: Remove old samsung-time driver
ARM: SAMSUNG: Move all platforms to new clocksource driver
ARM: SAMSUNG: Set PWM platform data
ARM: SAMSUNG: Add new PWM platform device
ARM: SAMSUNG: Unify base address definitions of timer block
clocksource: samsung_pwm_timer: Handle suspend/resume correctly
clocksource: samsung_pwm_timer: Do not use clocksource_mmio
clocksource: samsung_pwm_timer: Cache clocksource register address
clocksource: samsung_pwm_timer: Correct definition of AUTORELOAD bit
clocksource: samsung_pwm_timer: Do not request PWM mem region
+ v3.11-rc4
Conflicts:
arch/arm/Kconfig.debug
Signed-off-by: Olof Johansson <olof@lixom.net>
Now that all the needed pieces for DRA7 based SoCs' is present, enable
the build support in omap2plus_defconfig
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
The soc_ops for dra7xx devices can be completed reused
from the ones used for omap4 and omap5 devices.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The DRA7xx is a high-performance, infotainment application device,
based on enhanced OMAP architecture integrated on a 28-nm technology.
Since DRA7 is a platform supported only using DT, the cpu detection
is based on the compatibles passed from DT blobs as suggested here
http://lists.infradead.org/pipermail/linux-arm-kernel/2013-July/187712.html
Suggested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
