The l3 interconnect ip is same for OMAP4 and OMAP5.
So reuse the l3 error handler error code for OMAP5
as well. Also a few targets has been newly added for
OMAP5. So updating the driver for that here.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
GPMC module is the same as in OMAP4.
Just update the base address and irq number.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Adding the Initialisaton for clocksource and clockevent device
on OMAP5 Socs.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
OMAP5430 is Texas Instrument's SOC based on ARM Cortex-A15 SMP
architecture. It's a dual core SOC with GIC used for interrupt
handling and with an integrated L2 cache controller.
OMAP5432 is another variant of OMAP5430, with a
memory controller supporting DDR3 and SATA.
Patch includes:
- The machine specific headers and sources updates.
- Platform header updates.
- Minimum initialisation support for serial.
- IO table init
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Adding the OMAP5 ES1.0, 2.0 and OMAP5432 cpu revision
detection support.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
If provided dt support, then skip add wdt platform device as usual.
Signed-off-by: Xiao Jiang <jgq516@gmail.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently most ads7846 config definitions for OMAP3 series boards have
been moved to common-board-devices.c, and it is transparent for init.
And it's no very proper to do gpio_request based on get_pendown_state
since omap_ads7846_init knows everything about ads7846_config.
So it's more fit to request gpio according to the right gpio_pendown
and set debounce time conditionally. If we don't set proper debouce
time, there are flooded interrupt counters of ads7846 responding to
one time touch on screen, then the driver couldn't work very well.
This patch has been validated on 3530evm.
Signed-off-by: Zumeng Chen <zumeng.chen@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This was chosen by following the trace on the schematic from component U131
and U134 to the CPEN pin on the USB3320 device.
TWL4030.GPIO2-...->(T2_GPIO2_3V3)U131-..>nUSB2_EN-..>U134-..>EXP_nUSB2_1V8
which starts EHCI tranceiver USB3320.
This will set TWL4030.GPIO2 as output pin to drive EHCI tranceiver.
Signed-off-by: Zumeng Chen <zumeng.chen@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
EHCI PHY requires these regulators:
EVM Rev >=E --> VAUX2
EVM Rev < E --> VUSB1V5, VUSB1V8
Adding USB internal LDOs (vusb1v5 & vusb1v8) and VAUX2 to omap3evm
board file. Also removing vaux2_{1/2/3} supplies as they are not
used on omap3 evm.
But we need not to add vaux2 in twl4030_platform_data since it will
be added conditionally.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Zumeng Chen <zumeng.chen@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With omap_hwmod_get_main_clk() now available, this can be passed to
clk_get() to extract the fclk and thus avoid construction of fclk name.
Corrected the timer fck name mis-match between clock44xx_data.c and
omap_hwmod_44xx_data.c. For other platforms this is already taken care.
Cc: Cousson, Benoit <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit ac5b0ea3d (Merge tag 'omap-devel-f-for-3.6'...) had a merge
conflict that somehow got incorrecly resolved in a lossy way for
commit bed9d1bb (ARM: OMAP2+: hwmod: add omap_hwmod_get_main_clk() API).
Fix the issue by applying the missing pieces.
Reported-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Kevin discovered that commit c8d82ff68f
("ARM: OMAP2/3: hwmod data: Add 32k-sync timer data to hwmod
database") broke CORE idle on OMAP3. This prevents device low power
states.
The root cause is that the 32K sync timer IP block does not support
smart-idle mode[1], and so the hwmod code keeps the IP block in
no-idle mode while it is active. This in turn prevents the WKUP
clockdomain from transitioning to idle. There is a hardcoded sleep
dependency that prevents the CORE_L3 and CORE_CM clockdomains from
transitioning to idle when the WKUP clockdomain is active[2], so the
chip cannot enter any device low power states.
It turns out that there is no need to take the 32k sync timer out of
idle. The IP block itself probably does not have any native idle
handling at all, due to its simplicity. Furthermore, the PRCM will
never request target idle for this IP block while the kernel is
running, due to the sleep dependency that prevents the WKUP
clockdomain from idling while the CORE_L3 clockdomain is active. So
we can safely leave the 32k sync timer in target-force-idle mode, even
while we continue to access it.
This workaround is implemented by defining a new clockdomain flag,
CLKDM_ACTIVE_WITH_MPU, that indicates that the clockdomain is
guaranteed to be active whenever the MPU is inactive. If an IP
block's main functional clock exists inside this clockdomain, and the
IP block does not support smart-idle modes, then the hwmod code will
place the IP block into target force-idle mode even when enabled. The
WKUP clockdomains on OMAP3/4 are marked with this flag. (On OMAP2xxx,
no OCP header existed on the 32k sync timer.) Other clockdomains also
should be marked with this flag, but those changes are deferred until
a later merge window, to create a minimal fix.
Another theoretically clean fix for this problem would be to implement
PM runtime-based control for 32k sync timer accesses. These PM
runtime calls would need to located in a custom clocksource, since the
32k sync timer is currently used as an MMIO clocksource. But in
practice, there would be little benefit to doing so; and there would
be some cost, due to the addition of unnecessary lines of code and the
additional CPU overhead of the PM runtime and hwmod code - unnecessary
in this case.
Another possible fix would have been to modify the pm34xx.c code to
force the IP block idle before entering WFI. But this would not have
been an acceptable approach: we are trying to remove this type of
centralized IP block idle control from the PM code.
This patch is a collaboration between Kevin Hilman <khilman@ti.com>
and Paul Walmsley <paul@pwsan.com>.
Thanks to Vaibhav Hiremath <hvaibhav@ti.com> for providing comments on
an earlier version of this patch. Thanks to Tero Kristo
<t-kristo@ti.com> for identifying a bug in an earlier version of this
patch. Thanks to Benoît Cousson <b-cousson@ti.com> for identifying
some bugs in several versions of this patch and for implementation
comments.
References:
1. Table 16-96 "REG_32KSYNCNT_SYSCONFIG" of the OMAP34xx TRM Rev. ZU
(SWPU223U), available from:
http://www.ti.com/pdfs/wtbu/OMAP34x_ES3.1.x_PUBLIC_TRM_vzU.zip
2. Table 4-72 "Sleep Dependencies" of the OMAP34xx TRM Rev. ZU
(SWPU223U)
3. ibid.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The function __omap2_set_globals() can be common across all
platforms/architectures, even in case of omap4, internally it
calls same set of functions as in __omap2_set_globals() function
(except for sdrc).
This patch adds new config flag SOC_HAS_OMAP2_SDRC to handle sdrc,
so that we can reuse same function across omap2/3/4...
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As per recent discussion on the linux-omap list, we are
moving in the direction where, we will have only architecture,
ARCH_OMAP2PLUS and all devices/platforms will be treated
as a SoC underneath.
So the first step in this direction is to adopt this change
for all new devices getting in, converting
cpu_is_am33xx/335x() ==> soc_is_am33xx/335x()
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Initially, we decided to make am33xx family of device to fall
under omap3 class (cpu_is_omap34xx() = true), since it carries
Cortex-A8 core. But while adding complete baseport support
(like, clock, power and hwmod) support, it is observed that,
we are creating more and more problems by treating am33xx device
as omap3 family, as nothing matches between them
(except cortex-A8 mpu).
So, after long discussion we have came to the conclusion that,
we should not consider am33xx device as omap3 family, instead
create separate class (SOC_AM33XX) under OMAP2PLUS.
This means, for am33xx device, cpu_is_omap34xx() will return false,
and only cpu_is_am33xx() will be true.
Please refer to the link below, for mailing-list discussion on this -
http://www.spinics.net/lists/linux-omap/msg69439.html
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
[tony@atomide.com: fixed typo, updated for soc_is changes]
Signed-off-by: Tony Lindgren <tony@atomide.com>
In order to remove unnecessary idefs, move noncore and core
dpll ops to dpll3xxx.c file (where it should have been already).
The clkops (clkops_omap3_core_dpll_ops & clkops_omap3_noncore_dpll_ops)
is used in clock data files, and dependency is already handled by
Makefile rule.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Miscellaneous OMAP clock, hwmod, clockdomain, and powerdomain patches
for 3.6. Mostly small infrastructure improvements, and preparation
for OMAP5 and AM33xx code.
Conflicts:
arch/arm/mach-omap2/omap_hwmod.c
arch/arm/plat-omap/include/plat/omap_hwmod.h
The commit 503d0ea24d
ARM: OMAP4: hwmod data: Add aliases for McBSP fclk clocks
added a wrong "prcm_clk" alias for PRCM clock whereas the McBSP
driver and previous OMAPs are using "prcm_fck".
It thus lead to the following warning.
[ 47.409729] omap-mcbsp: clks: could not clk_get() prcm_fck
Fix that by changing the opt_clk role to prcm_fck.
Reported-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Sebastien Guiriec <s-guiriec@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The OMAP4 usb_host_fs (OHCI) and AESS IP blocks require some special
programming for them to enter idle. Without this programming, they
will prevent the rest of the chip from entering full chip idle.
To implement the idle programming cleanly, this will take some
coordination between maintainers. This is likely to take some time,
so it is probably best to leave this for 3.6 or 3.7. So, in the
meantime, prevent these IP blocks from being registered.
Later, once the appropriate support is available, this patch can be
reverted.
This second version comments out the IP block data since Benoît didn't
like removing it.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
The DMADISABLE bit is a semi-automatic bit present in sysconfig register
of some modules. When the DMA must perform read/write accesses, the
DMADISABLE bit is cleared by the hardware. But when the DMA must stop for power
management, software must set the DMADISABLE bit back to 1.
In cases where the ROMCODE/BOOTLOADER uses dma, the hardware clears the
DMADISABLE bit (but the romcode/bootloader might not set it back to 1).
In order for the kernel to start in a clean state, it is
necessary for the kernel to set DMADISABLE bit back to 1 (irrespective
of whether it's been set to 1 in romcode or bootloader).
During _reset of the (hwmod)device, the DMADISABLE bit is set so that it
does not prevent idling of the system. (NOTE: having DMADISABLE to 0,
prevents the system to idle)
DMADISABLE bit is present in usbotgss module of omap5.
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[paul@pwsan.com: updated to apply; fixed checkpatch warnings]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some prm and cm registers read/write and status functions
are built only for some custom OMAP2+ builds and are stubbed
in header files for other builds under ifdef statements.
But this results in adding new CONFIG_ARCH_OMAPXXX
checks when SOCs are added in the future. So move them
to a common place for OMAP2+ and make them 'weak' implementations.
This way no new ifdefs would be required in the future and also
cleans up the existing code.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
[paul@pwsan.com: unsplit quoted strings; moved PRM functions to
mach-omap2/prm_common.c; resolved sparse warnings]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The register is used to configure the behaviour of the CSI-2 and CCP-2
receivers. This register is available only in OMAP3630.
The original patch was submitted by Vimarsh Zutshi.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Cc: Vimarsh Zutshi <vimarsh.zutshi@gmail.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The wake-up power domain is an alway-on power domain and so this power domain
does not have a power state status (PM_PWSTST_xxx) register that indicates the
current state. However, during the registering of the wake-up power domain the
state of the domain is queried by calling pwrdm_read_pwrst(). This actually
tries to read a register that does not exist and returns a value of 0 that
indicates that the current state is OFF. The OFF state count of the wake-up
power domain is then set to 1 and the current state to OFF. Both of which are
incorrect.
To fix this, if a power domain only supports the ON state, do not attempt to
read the power state status register and simply return ON as the current power
state.
This is based upon Tony's current linux-omap master branch.
Testing:
- Boot tested on OMAP4460 panda.
- Boot tested on OMAP3430 beagle and validated CORE RET still working (using
Paul's 32k timer patch [1]).
[1] http://marc.info/?l=linux-omap&m=134000053229888&w=2
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[paul@pwsan.com: edited commit message slightly]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
For OMAP3+ devices, the clock domains (CLKDMs) support one or more of the
following transition modes ...
NO_SLEEP (0x0) - A clock domain sleep transition is never initiated,
irrespective of the hardware conditions.
SW_SLEEP (0x1) - A software-forced sleep transition. The transition is initiated
when the associated hardware conditions are satisfied
SW_WKUP (0x2) - A software-forced clock domain wake-up transition is initiated,
irrespective of the hardware conditions.
HW_AUTO (0x3) - Hardware-controlled automatic sleep and wake-up transition is
initiated by the PRCM module when the associated hardware
conditions are satisfied.
For OMAP4 devices, SW_SLEEP is equivalent to HW_AUTO and NO_SLEEP is equivalent
to SW_WKUP. The only difference between HW_AUTO and SW_SLEEP for OMAP4 devices
is that the PRM_IRQSTATUS_MPU.TRANSITION_ST interrupt status is set in case of
SW_SLEEP transition, and not set in case of HW_AUTO transition.
For OMAP4 devices, all CLKDMs support HW_AUTO and therefore we can place the
CLKDMs in the HW_AUTO state instead of the SW_SLEEP mode. Hence, we do not
need to use the SW_SLEEP mode. With regard to NO_SLEEP and SW_WKUP it is
preferred to use SW_WKUP mode if the CLKDM supports it and so use this mode
instead of NO_SLEEP where possible.
For a software perspective the above 4 modes are represented by the following
flags to indicate what modes are supported by each of the CLKDMs.
CLKDM_CAN_DISABLE_AUTO --> NO_SLEEP
CLKDM_CAN_ENABLE_AUTO --> HW_AUTO
CLKDM_CAN_FORCE_SLEEP --> SW_SLEEP
CLKDM_CAN_FORCE_WAKEUP --> SW_WKUP
By eliminating the SW_SLEEP mode the the mapping of the flags for OMAP4 devices
can becomes ...
CLKDM_CAN_DISABLE_AUTO --> NO_SLEEP
CLKDM_CAN_ENABLE_AUTO --> HW_AUTO
CLKDM_CAN_FORCE_SLEEP --> HW_AUTO
CLKDM_CAN_FORCE_WAKEUP --> SW_WKUP
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Reviewed-by: Benoit Cousson <b-cousson@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In case of AM33xx family of devices (like cpsw) have different sysc
bit field offsets defined,
sysc_type3:
| 3 2 | 1 0 |
| STDBYMODE | IDLEMODE |
So introduce new sysc_type3 in omap_hwmod common data.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
From Tony Lindgren <tony@atomide.com>:
Here are changes to add support for am33xx processors for the
clock, power, and voltagedomains.
* tag 'omap-devel-am33xx-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP AM33xx: clockdomains: Add clockdomain data and respective operations
ARM: OMAP AM33xx: powerdomains: add AM335x support
ARM: OMAP AM33xx: CM: Introduce AM33xx CM APIs and register level details
ARM: OMAP AM33xx: PRM: add PRM support
ARM: OMAP AM33xx: voltagedomain: Add voltage domain data
ARM: OMAP2+: control: Add AM33XX control reg & sec clkctrl offset
ARM: OMAP2+: am33xx: Add AM335XEVM machine support
ARM: OMAP2+: am33xx: Add low level debugging support
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From: Tony Lindgren <tony@atomide.com>:
Here are some omap PM changes that reimplement omap PRCM I/O chain
code for wake-ups, and improve idle latencies for cpuidle.
* tag 'omap-devel-pm-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: PM: fix IRQ_NOAUTOEN removal by mis-merge
ARM: OMAP3: PM: cpuidle: optimize the clkdm idle latency in C1 state
ARM: OMAP3: PM: cpuidle: optimize the PER latency in C1 state
ARM: OMAP3: PM: cpuidle: default to C1 in next_valid_state
ARM: OMAP3: PM: cleanup cam_pwrdm leftovers
ARM: OMAP3: PM: call pre/post transition per powerdomain
ARM: OMAP2+: powerdomain: allow pre/post transtion to be per pwrdm
ARM: OMAP3: PM: Remove IO Daisychain control from cpuidle
ARM: OMAP3PLUS: hwmod: reconfigure IO Daisychain during hwmod mux
ARM: OMAP3+: PRM: Enable IO wake up
ARM: OMAP4: PRM: Add IO Daisychain support
ARM: OMAP3: PM: Move IO Daisychain function to omap3 prm file
ARM: OMAP3: PM: correct enable/disable of daisy io chain
ARM: OMAP2+: PRM: fix compile for OMAP4-only build
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Tony Lindgren <tony@atomide.com>:
Here are some omap dmtimer changes to make it easier to add
device tree support for dmtimer by simplifying the platform
data structure used by dmtimr.
* tag 'omap-devel-dmtimer-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Simplify dmtimer clock aliases
ARM: OMAP2+: Move dmtimer clock set function to dmtimer driver
ARM: OMAP1: Fix dmtimer support
ARM: OMAP: Add flag to indicate if a timer needs a manual reset
ARM: OMAP: Remove timer function pointer for context loss counter
ARM: OMAP: Remove loses_context variable from timer platform data
ARM: OMAP2+: Fix external clock support for dmtimers
ARM: OMAP2+: HWMOD: Correct timer device attributes
ARM: OMAP: Add DMTIMER capability variable to represent timer features
ARM: OMAP2+: Add dmtimer platform function to reserve systimers
ARM: OMAP2+: Remove unused max number of timers definition
ARM: OMAP: Remove unnecessary clk structure
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Tony Lindgren <tony@atomide.com>
Here is some more omap clean-up. The biggest changes are
hwmod, clock, and System Control Module cleanup, and the removal
of the last instance of omap_read/write usage for omap2+ with
the removal of unused USB OHCI Full Speed driver support. The
removed OHCI is only currently used for omap1 as the actively
used omap2+ boards have either MUSB or another instance of
OHCI+EHCI that's more usable.
* tag 'omap-cleanup-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: hwmod: remove prm_clkdm, cm_clkdm; allow hwmods to have no clockdomain
ARM: OMAP3: Move McBSP fck clock alias to hwmod data
ARM: OMAP2: Move McBSP fck clock alias to hwmod data for OMAP2430
ARM: OMAP2: Move McBSP fck clock alias to hwmod data for OMAP2420
ARM: OMAP: dsp: interface to control module functions
ARM: OMAP2+: control: new APIs to configure boot address and mode
ARM: OMAP2+: CLEANUP: Remove ARCH_OMAPx ifdef from struct dpll_data
ARM: OMAP2+: hwmod: use init-time function pointer for _init_clkdm
ARM: OMAP2+: hwmod: use init-time function pointer for hardreset
ARM: OMAP2+: hwmod: use init-time function pointer for wait_target_ready
ARM: OMAP4: hwmod: drop extra cpu_is check from _wait_target_disable()
ARM: OMAP2+: hwmod: use init-time function ptrs for enable/disable module
ARM: OMAP4: hwmod: rename _enable_module to _omap4_enable_module()
ARM: OMAP: Make FS USB omap1 only
ARM: OMAP2: Remove legacy USB FS support
ARM: OMAP3: There is no FS USB controller on omap3
ARM: OMAP: dma: Clear status registers on enable/disable irq
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Tony Lindgren <tony@atomide.com>:
This branch contains fixes that were too intrusive or not
critical enough for the 3.5 -rc cycle. The biggest changes are
fixes for the am35xx clock and hwmod data, and the removal of dead
code for the 730 and 850 headers.
* tag 'omap-fixes-non-critical-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (25 commits)
ARM: OMAP2+: fix CONFIG_CPU_IDLE dependency on CONFIG_PM
ARM: OMAP: remove unused cpu detection macros
ARM: OMAP: fix typos related to OMAP330
ARM: OMAP7XX: Remove omap730.h and omap850.h
ARM: OMAP2+: fix naming collision of variable nr_irqs
ARM: OMAP: omap2plus_defconfig: Enable EXT4 support
ARM: OMAP depends on MMU
arm: omap3: am35x: Set proper powerdomain states
ARM: OMAP AM35x: clockdomain data: Fix clockdomain dependencies
ARM: OMAP AM35x: EMAC/MDIO integration: Add Davinci EMAC/MDIO hwmod support
ARM: OMAP: AM35xx: fix UART4 softreset
ARM: OMAP AM35xx: clock and hwmod data: fix UART4 data
ARM: OMAP AM35xx: clock and hwmod data: fix AM35xx HSOTGUSB hwmod
ARM: OMAP: Fix dts files w/ status property: "disable" -> "disabled"
ARM: OMAP: beagle: Set USB Host Port 1 to OMAP_USBHS_PORT_MODE_UNUSED
ARM: OMAP2: twl-common: Fix compiler warning
ARM: OMAP: fix the ads7846 init code
mfd: twl: remove pdata->irq_base/_end, no more users
ARM: OMAP2+: TWL: remove usage of pdata->irq_base/_end
ARM: OMAP2+: OPP: Fix to ensure check of right oppdef after bad one
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The SYS_NIRQ1 pin is the interupt line for the PMIC part of the TWL6030
and interrupts from the PMIC are needed as wakeup sources.
Ensure this pin is mux'd as input and has wakeup enabled so PMIC
interupts (e.g. RTC) can be used as wakeup sources.
Tested on OMAP4430/Panda.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In order for suspend/resume dependencies to work correctly, I2C has to
be initialized (more specifically, registered with the driver core)
before MMC. Without this, the MMC driver fails to adjust the VMMC
regulator (using i2c writes) during the suspend path.
Problem found testing suspend/resume on 3730/OveroSTORM platform.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Register OMAP DRM/KMS platform device. DMM is split into a
separate device using hwmod.
Signed-off-by: Andy Gross <andy.gross@ti.com>
Signed-off-by: Rob Clark <rob.clark@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM33XX clock implementation is different than any existing OMAP
family of devices. Although DPLL module is similar to OMAP4
device, but the usage is very much different than OMAP4.
AM33XX has different peripheral set and each module gets
integrated to the clock framework differently than OMAP
family of devices.
This patch adds full Clock tree data for AM33XX family
of devices and also integrates it into existing OMAP framework.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
CC: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: updated to apply; changed 'soc_is_am33xx' to
'cpu_is_am33xx' to match usage in Tony's current am33xx branch]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
commit 99b59df0 (ARM: OMAP3: PM: fix shared PRCM interrupt leave
disabled at boot) added IRQ_NOAUTOEN to the PRCM interrupt so it could
be enabled later if needed. However, this commit was partially undone
when merging the IO daisy chain rework in 9a17d88e (Merge tag
'omap-devel-c-for-3.6' of
git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into
devel-pm
This patch adds back the IRQ_NOAUTOEN fix that was removed by the
merge resolution.
This also fixes the following boot-time warning that showed up after
merging the IO daisy chain rework:
[ 3.849334] WARNING: at kernel/irq/manage.c:436 enable_irq+0x3c/0x78()
[ 3.856231] Unbalanced enable for IRQ 297
[ 3.860473] Modules linked in:
[ 3.863739] [<c001a114>] (unwind_backtrace+0x0/0xf0) from [<c003c7e8>] (warn_slowpath_common+0x4c/0x64)
[ 3.873687] [<c003c7e8>] (warn_slowpath_common+0x4c/0x64) from [<c003c894>] (warn_slowpath_fmt+0x30/0x40)
[ 3.883819] [<c003c894>] (warn_slowpath_fmt+0x30/0x40) from [<c00993e0>] (enable_irq+0x3c/0x78)
[ 3.893035] [<c00993e0>] (enable_irq+0x3c/0x78) from [<c067b1e8>] (omap3_pm_init+0x328/0x5f4)
[ 3.902099] [<c067b1e8>] (omap3_pm_init+0x328/0x5f4) from [<c067161c>] (init_machine_late+0x1c/0x28)
[ 3.911773] [<c067161c>] (init_machine_late+0x1c/0x28) from [<c0008648>] (do_one_initcall+0x34/0x178)
[ 3.921539] [<c0008648>] (do_one_initcall+0x34/0x178) from [<c066e8f4>] (kernel_init+0xfc/0x1c0)
[ 3.930847] [<c066e8f4>] (kernel_init+0xfc/0x1c0) from [<c00140b0>] (kernel_thread_exit+0x0/0x8)
[ 3.940246] ---[ end trace 55a0ad32ca2ca682 ]---
Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some OMAP AM35xx fixes.
The powerdomain and clockdomain data for the AM35xx are finally fixed.
The AM35xx EMAC/MDIO Ethernet controller integration code has been
converted to use the OMAP device and hwmod framework. Also the UART4
and HSOTGUSB warnings have been fixed.
commit 164e0cbf60 (ARM: OMAP3/4: consolidate cpuidle Makefile) added
an OMAP-specific dependency from CPU_IDLE to CONFIG_PM. This causes
some randconfig warnings when CONFIG_PM has unmet dependencies:
warning: (ARCH_OMAP3 && ARCH_OMAP4) selects PM which has unmet direct dependencies (PM_SLEEP || PM_RUNTIME)
warning: (ARCH_OMAP3 && ARCH_OMAP4) selects PM which has unmet direct dependencies (PM_SLEEP || PM_RUNTIME)
warning: (ARCH_OMAP3 && ARCH_OMAP4) selects PM which has unmet direct dependencies (PM_SLEEP || PM_RUNTIME)
Fix this by making the dependency on CONFIG_PM_RUNTIME (which in turn
will enable CONFIG_PM.)
Reported-by: Tony Lindgren <tony@atomide.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
