This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
781e989cf5 ("mmc: sdhci: convert to new SDIO IRQ handling") and
bf3b5ec66b ("mmc: sdio_irq: rework sdio irq handling") disabled
the use of our own custom threaded IRQ handler, but left in an
unconditional wake_up_process() on that handler at resume-time.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=80151
In addition, the check for MMC_CAP_SDIO_IRQ capability is added
before enable sdio IRQ.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
Signed-off-by: Fu Zhonghui <zhonghui.fu@linux.intel.com>
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are upcoming MIPS SoCs with dw_mmc hosts.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The dw_mmc drivers rely on the DMA API, so update the Kconfig entry
to depend on HAS_DMA. Since the drivers should build on any platform
with DMA, allow the driver to compile tested on non-ARC/ARM platforms.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
when SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK is set, timeout_clk is sdclk.
We need to update it when we change sdclk in sdhci_set_clock.
This allow to have a more precisse timeout and max_busy_timeout. This
can help for command that need a big busy wait (erase, ...).
Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When we wait for busy after sending a command, if there is
a timeout, we got SDHCI_INT_DATA_TIMEOUT flags.
Before this commit we got the message :
"Got data interrupt 0x00100000 even though no data operation was in progress."
and we need to wait 10s that sdhci_timeout_timer expires.
Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current code erroneously fill the last byte of R2 response with an undefined
value. In addition, the controller actually 'offloads' the last byte
(CRC7, end bit) while receiving R2 response and thus it's impossible to get the
actual value. This could cause mmc stack to obtain inconsistent CID from the
same card after resume and misidentify it as a different card.
Fix by assigning dummy CRC and end bit: {7'b0, 1} = 0x1 to the last byte of R2.
Cc: <stable@vger.kernel.org> # v3.16+
Fixes: c7f6558d84 ("mmc: Add realtek USB sdmmc host driver")
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current code erroneously fill the last byte of R2 response with an undefined
value. In addition, the controller actually 'offloads' the last byte
(CRC7, end bit) while receiving R2 response and thus it's impossible to get the
actual value. This could cause mmc stack to obtain inconsistent CID from the
same card after resume and misidentify it as a different card.
Fix by assigning dummy CRC and end bit: {7'b0, 1} = 0x1 to the last byte of R2.
Cc: <stable@vger.kernel.org> # v3.8+
Fixes: ff984e57d3 ("mmc: Add realtek pcie sdmmc host driver")
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If we happened to get a data error at just the wrong time the dw_mmc
driver could get into a state where it would never complete its
request. That would leave the caller just hanging there.
We fix this two ways and both of the two fixes on their own appear to
fix the problems we've seen:
1. Fix a race in the tasklet where the interrupt setting the data
error happens _just after_ we check for it, then we get a
EVENT_XFER_COMPLETE. We fix this by repeating a bit of code.
2. Fix it so that if we detect that we've got an error in the "data
busy" state and we're not going to do anything else we end the
request and unblock anyone waiting.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@gmail.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
curr should use signed type since it will contain the returned
value which is possible to be a negative value. Using u32 will
make the returned value to be true even there is a negative result.
Change to use int instead of u32
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make use of the MMC asynchronous request capability to prepare the
next DMA transfer request in parallel with the current transfer.
This is done by adding pre-request and post-request callbacks that are
used by the MMC framework during an active data transfer.
It should help reduce the impact of DMA preparation overhead on the SD
card performance.
Signed-off-by: Apelete Seketeli <apelete@seketeli.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Until now the MMC driver for JZ4740 SoC was relying on PIO mode only
for data transfers.
This patch allows the use of DMA for data trasnfers in addition to PIO
mode by relying on DMA Engine.
DMA tranfers performance might be further improved by taking advantage
of the asynchronous request capability of the MMC framework.
Signed-off-by: Apelete Seketeli <apelete@seketeli.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch focuses on clock setting for RK3288 mmc controller.
In RK3288 mmc controller, CLKDIV register can only be set 0 or 1,
and if DDR 8bit mode, CLKDIV register must be set 1.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The code selecting a device for the sdhci host has been
continuously tweaked (4b711cb138
"mmc: sdhci-pltfm: Add structure for host-specific data" and
a4d2177f00 "mmc: sdhci-pltfm: dt
device does not pass parent to sdhci_alloc_host" while there
does not seem to be any reason to use platform device's parent
in the first place.
The comment saying "Some PCI-based MFD need the parent here"
seem to refer to Timberdale FPGA driver (the only MFD driver
registering SDHCI cell, drivers/mfd/timberdale.c) but again,
the only situation when parent device matter is runtime PM,
which is not implemented for Timberdale.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no need for regulator consumers to include special logic for
fixed voltage regulators as they support regulator_set_voltage() just
like their non-fixed regulator counterparts.
Signed-off-by: Tim Kryger <tim.kryger@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On Qualcomm APQ8064 SOCs, SD card controller has an additional glue
called DML (Data Mover Local/Lite) to assist dma transfers.
This hardware needs to be setup before any dma transfer is requested.
DML itself is not a DMA engine, its just a gule between the SD card
controller and dma controller.
Most of this code has been ported from qualcomm's 3.4 kernel.
This patch adds the code necessary to intialize the hardware and setup
before doing any dma transfers.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Miscellaneous
- Remove DEFINE_PCI_DEVICE_TABLE macro use (Benoit Taine)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jJGu
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull DEFINE_PCI_DEVICE_TABLE removal from Bjorn Helgaas:
"Part two of the PCI changes for v3.17:
- Remove DEFINE_PCI_DEVICE_TABLE macro use (Benoit Taine)
It's a mechanical change that removes uses of the
DEFINE_PCI_DEVICE_TABLE macro. I waited until later in the merge
window to reduce conflicts, but it's possible you'll still see a few"
* tag 'pci-v3.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Remove DEFINE_PCI_DEVICE_TABLE macro use
- Forward compatibility for eMMC.
- Fix some blacklisted cards with broken secure discard.
MMC host:
- mmci: Add support for Qualcomm variant.
- mmci: Fix regression for arm_variant.
- sdhci: Various fixes and cleanups.
- sdhci: Improve external VDD regulator support.
- sdhci: Support for DDR50 1.8V mode for BayTrail.
- sdhci-st: Add driver for ST SDHCI controller.
- sh-mmcif: DMA fixes.
- omap_hsmmc: Add support for SDIO interrupts.
- sdhci-pci: Add support for Intel Quark X1000.
- dw_mmc: Update the reset sequence.
- s3cmci: port DMA code to dmaengine API.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=kGSY
-----END PGP SIGNATURE-----
Merge tag 'mmc-v3.17-1' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC updates from Ulf Hansson:
"Me and Chris Ball decided to try out using my MMC tree as the primary
one, to simplify handling of patches.
This pull does thus contains all the MMC patches for 3.17 rc1, no pull
from Chris this time.
Details:
MMC core:
- forward compatibility for eMMC
- fix some blacklisted cards with broken secure discard
MMC host:
- mmci: Add support for Qualcomm variant
- mmci: Fix regression for arm_variant
- sdhci: Various fixes and cleanups
- sdhci: Improve external VDD regulator support
- sdhci: Support for DDR50 1.8V mode for BayTrail
- sdhci-st: Add driver for ST SDHCI controller
- sh-mmcif: DMA fixes
- omap_hsmmc: Add support for SDIO interrupts
- sdhci-pci: Add support for Intel Quark X1000
- dw_mmc: Update the reset sequence
- s3cmci: port DMA code to dmaengine API"
* tag 'mmc-v3.17-1' of git://git.linaro.org/people/ulf.hansson/mmc: (67 commits)
mmc: dw_mmc: modify the dt-binding for removing slot-node and supports-highspeed
mmc: dw_mmc: Slot quirk "disable-wp" is deprecated.
mmc: mmci: Reverse IRQ handling for the arm_variant
mmc: mmci: Move all CMD irq handling to mmci_cmd_irq()
mmc: mmci: Remove redundant check of status for DATA irq
mmc: dw_mmc: change to use recommended reset procedure
mmc: sdhci-pxav3: Use devm_* managed helpers
mmc: tmio: Configure DMA slave bus width
mmc: sh_mmcif: Configure DMA slave bus width
mmc: sh_mmcif: Fix DMA slave address configuration
mmc: sh_mmcif: Document DT bindings
mmc: sdhci-pci: remove PCI PM functions in suspend/resume callback
mmc: Do not advertise secure discard if it is blacklisted
mmc: sdhci-msm: Get COMPILE_TEST support
mmc: sdhci-msm: Remove unnecessary header file inclusion
mmc: sdhci-msm: Fix the binding example
mmc: sdhci: add DDR50 1.8V mode support for BayTrail eMMC Controller
mmc: sdhci: Preset value not supported in Baytrail eMMC
mmc: MMC_USDHI6ROL0 should depend on HAS_DMA
mmc: MMC_SH_MMCIF should depend on HAS_DMA
...
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit "mmc: mmci: Handle CMD irq before DATA irq", caused an issue
when using the ARM model of the PL181 and running QEMU.
The bug was reported for the following QEMU version:
$ qemu-system-arm -version
QEMU emulator version 2.0.0 (Debian 2.0.0+dfsg-2ubuntu1.1), Copyright
(c) 2003-2008 Fabrice Bellard
To resolve the problem, let's restore the old behavior were the DATA
irq is handled prior the CMD irq, but only for the arm_variant, which
the problem was reported for.
Reported-by: John Stultz <john.stultz@linaro.org>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
Tested-by: Kees Cook <keescook@chromium.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch won't change the behavior of how mmci deals with CMD irqs.
By moving code from mmci_irq() to mmci_cmd_irq(), we getter a better
overview of what going on.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
Tested-by: Kees Cook <keescook@chromium.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We don't need to verify the content of the status register twice, while
we are about to handle a DATA irq. Instead let's leave all verification
to be handled by mmci_data_irq().
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
Tested-by: Kees Cook <keescook@chromium.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch changes the fifo reset code to follow the reset procedure
outlined in the documentation of Synopsys Mobile storage host databook.
Signed-off-by: Sonny Rao <sonnyrao@chromium.org>
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
[sonnyrao: fix compile for !CONFIG_MMC_DW_IDMAC case]
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Checkpatch fixes throughout the subsystem
- Use Regmap to handle IRQs in max77686, extcon-max77693 and mc13xxx-core
- Use DMA in rtsx_pcr
- Restrict building on unsupported architectures on timberdale, cs5535
- SPI hardening in cros_ec_spi
- More robust error handing in asic3, cros_ec, ab8500-debugfs,
max77686 and pcf50633-core
- Reorder PM runtime and regulator handing during shutdown in arizona
- Enable wakeup in cros_ec_spi
- Unused variable/code clean-up in pm8921-core, cros_ec, htc-i2cpld,
tps65912-spi, wm5110-tables and ab8500-debugfs
- Add regulator handing into suspend() in sec-core
- Remove pointless wrapper functions in extcon-max77693 and i2c-cros-ec-tunnel
- Use cross-architecture friendly data sizes in stmpe-i2c, arizona,
max77686 and tps65910
- Device Tree documentation updates throughout
- Provide power management support in max77686
- Few OF clean-ups in max77686
- Use manged resources in tps6105x
== New drivers/supported devices ==
- Add support for s2mpu02 to sec-core
- Add support for Allwinner A32 to sun6i-prcm
- Add support for Maxim 77802 in max77686
- Add support for DA9063 AD in da9063
- Add new driver for Intel PMICs (generic) and specifically Crystal Cove
== (Re-)moved drivers ==
- Move out keyboard functionality cros_ec ==> input/keyboard/cros_ec_keyb
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2cNI
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD update from Lee Jones:
"Changes to existing drivers:
- checkpatch fixes throughout the subsystem
- use Regmap to handle IRQs in max77686, extcon-max77693 and
mc13xxx-core
- use DMA in rtsx_pcr
- restrict building on unsupported architectures on timberdale,
cs5535
- SPI hardening in cros_ec_spi
- more robust error handing in asic3, cros_ec, ab8500-debugfs,
max77686 and pcf50633-core
- reorder PM runtime and regulator handing during shutdown in arizona
- enable wakeup in cros_ec_spi
- unused variable/code clean-up in pm8921-core, cros_ec, htc-i2cpld,
tps65912-spi, wm5110-tables and ab8500-debugfs
- add regulator handing into suspend() in sec-core
- remove pointless wrapper functions in extcon-max77693 and
i2c-cros-ec-tunnel
- use cross-architecture friendly data sizes in stmpe-i2c, arizona,
max77686 and tps65910
- devicetree documentation updates throughout
- provide power management support in max77686
- few OF clean-ups in max77686
- use manged resources in tps6105x
New drivers/supported devices:
- add support for s2mpu02 to sec-core
- add support for Allwinner A32 to sun6i-prcm
- add support for Maxim 77802 in max77686
- add support for DA9063 AD in da9063
- new driver for Intel PMICs (generic) and specifically Crystal Cove
(Re-)moved drivers ==
- move out keyboard functionality cros_ec ==> input/keyboard/cros_ec_keyb"
* tag 'mfd-for-linus-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (101 commits)
MAINTAINERS: Update MFD repo location
mfd: omap-usb-host: Fix improper mask use.
mfd: arizona: Only free the CTRLIF_ERR IRQ if we requested it
mfd: arizona: Add missing handling for ISRC3 under/overclocked
mfd: wm5110: Add new interrupt register definitions
mfd: arizona: Rename thermal shutdown interrupt
mfd: wm5110: Add in the output done interrupts
mfd: wm5110: Remove non-existant interrupts
mfd: tps65912-spi: Remove unused variable
mfd: htc-i2cpld: Remove unused code
mfd: da9063: Add support for AD silicon variant
mfd: arizona: Map MICVDD from extcon device to the Arizona core
mfd: arizona: Add MICVDD to mapped regulators for wm8997
mfd: max77686: Ensure device type IDs are architecture agnostic
mfd: max77686: Add Maxim 77802 PMIC support
mfd: tps6105x: Use managed resources when allocating memory
mfd: wm8997-tables: Suppress 'line over 80 chars' warnings
mfd: kempld-core: Correct a variety of checkpatch warnings
mfd: ipaq-micro: Fix coding style errors/warnings reported by checkpatch
mfd: si476x-cmd: Remedy checkpatch style complains
...
Use the clock framework to get the peripheral clock rate to
correctly set the MMC/SD bus clock divider.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7475/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch changes all absolute SYS_XY registers to offsets from the
SYS block base, prefixes them with AU1000 to avoid silent failures due
to changed addresses, and introduces helper functions to read/write
them.
No functional changes, comparing assembly of a few select functions shows
no differences.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7464/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Even though some implementations support 4-bytes data register access,
the tmio driver never configures the hardware in such a way and always
performs 2-bytes accesses. Hardcode the DMA transfer size to 2 bytes.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The data register is 4 bytes wide, hardcode the DMA transfer size to
4 bytes in both directions.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit e5a233cb64 ("mmc: sh_mmcif:
Factorize DMA channel request and configuration code") incorrectly
set the destination address for both slave channels instead of setting
the source address for the receive channel. Fix that.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is not required (in fact it even is not recommended) that a PCI
driver's suspend() callback save the standard configuration registers
of the device, prepare it for waking up the system, or put it into a
low-power state. All of these operations can very well be taken
care of by the PCI subsystem, without the driver's participation. Thus
remove these PCI functions.
For the device which has wake up capability, use device_init_wakeup to
init the wake up capability so that PCI core will help to enable the wakeup
for it.
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently when the device secure discard implementation is
blacklisted (MMC_QUIRK_SEC_ERASE_TRIM_BROKEN quirk is set)
instead of secure discard we're going to do normal discard,
which is wrong.
When the secure discard is known to be broken we should just
disallow it entirely and not advertise this functionality to
the user. Fix it.
Also move mmc_fixup_device() in from of mmc_blk_alloc() so we
can get quirks set before we attempt to set queue information.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The header <linux/regulator/consumer.h> is unused. Remove it.
Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is to enable DDR50 bus speed mode with 1.8V signaling capability
for BayTrail ACPI and PCI mode eMMC Controller.
Signed-off-by: Maurice Petallo <mauricex.r.petallo@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
"SDHCI_QUIRK2_PRESET_VALUE_BROKEN" quirk is added to prohibit
preset value enabling for Baytrail eMMC controller.
Signed-off-by: Maurice Petallo <mauricex.r.petallo@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If NO_DMA=y:
drivers/built-in.o: In function `usdhi6_dma_setup':
usdhi6rol0.c:(.text+0x5c35fc): undefined reference to `dma_map_sg'
drivers/built-in.o: In function `usdhi6_dma_stop_unmap':
usdhi6rol0.c:(.text+0x5c3738): undefined reference to `dma_unmap_sg'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If NO_DMA=y:
drivers/built-in.o: In function `sh_mmcif_start_dma_tx':
sh_mmcif.c:(.text+0x5a3286): undefined reference to `dma_map_sg'
drivers/built-in.o: In function `sh_mmcif_start_dma_rx':
sh_mmcif.c:(.text+0x5a33fc): undefined reference to `dma_map_sg'
drivers/built-in.o: In function `sh_mmcif_end_cmd':
sh_mmcif.c:(.text+0x5a3668): undefined reference to `dma_unmap_sg'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If NO_DMA=y:
drivers/built-in.o: In function `omap_hsmmc_pre_dma_transfer':
omap_hsmmc.c:(.text+0x5a0928): undefined reference to `dma_map_sg'
drivers/built-in.o: In function `omap_hsmmc_dma_cleanup':
omap_hsmmc.c:(.text+0x5a0e8e): undefined reference to `dma_unmap_sg'
drivers/built-in.o: In function `omap_hsmmc_dma_callback':
omap_hsmmc.c:(.text+0x5a1f58): undefined reference to `dma_unmap_sg'
drivers/built-in.o: In function `omap_hsmmc_post_req':
omap_hsmmc.c:(.text+0x5a2082): undefined reference to `dma_unmap_sg'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This platform driver adds initial support for the SDHCI host controller
found on STMicroelectronics SoCs.
It has been tested on STiH41x b2020 platforms currently.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This doesn't seem to be used any longer and removing the include fixes
64-bit ARM builds.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In case of reboot my olinuxino imx23 board does not see
mmc card any more. mmc_rescan is being called by delayed
work in loop, but mxs_mmc_get_cd always returns 0, so we
will never pass the card detection check and will not do
further card inition.
This patch is just an attempt to partially revert the patch
a91fe279ae of Sascha Hauer, where it is claimed that upper
layer will handle broken card detection using the polling
logic and MMC_CAP_NEEDS_POLL capability, but seems it is not
true, because upper logic still expects 1 from 'get_cd'.
So, here we always return 1 (card present) in case of
MMC_CAP_NEEDS_POLL capability set.
Signed-off-by: Roman Pen <r.peniaev@gmail.com>
CC: Chris Ball <chris@printf.net>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
CC: Shawn Guo <shawn.guo@linaro.org>
CC: Ulf Hansson <ulf.hansson@linaro.org>
CC: linux-mmc@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use clk_prepare_enable/clk_disable_unprepare to make the driver
work properly with common clock framework.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As stated by the eMMC 5.0 specification, a chip should not be rejected
only because of the revision stated in the EXT_CSD_REV field of the
EXT_CSD register.
Remove the control on this value, the control of the CSD_STRUCTURE field
should be sufficient to reject future incompatible changes.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After the switch to the MMC core regulator infrastucture, we already
have a local "mmc" pointer in various functions. There is no longer a
need to access the data structure via host->mmc.
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMC core in mmc_set_signal_voltage() already provides for the delay
required to switch to 1.8V, so there is no need for drivers to perform
this wait themselves.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
While merging the sdhci patchset from Russell King, somehow a blank
line was left behind. Let's correct the formatting.
Cc: Chris Ball <chris@printf.net>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A standard compliant SDHCI can itself supply VDD at 1.8, 3.0, or 3.3v.
Several vendors ignore this and instead rely upon external regulators
to supply VDD. While the external regulators typically can supply one
of the standard SDHCI voltage levels, there is no real reason for this
to be a hard requirement.
This patch alters the SDHCI driver such that external VDD regulators
that provide voltages other than the three mentioned above may be used
so long as they can supply a voltage that meets the needs of the card.
In the case that an external VDD regulator is provided, it is reasonable
to ignore the voltage capabilities of the host controller and allow the
external regulator to set the OCR mask. Additionally, there is no need
to convert a VDD voltage request into one of the standard SDHCI voltage
levels or program it in the host controller's power control register.
Signed-off-by: Tim Kryger <tim.kryger@gmail.com>
Tested-by: Sachin Kamat <spk.linux@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's a NOOP since 2.6.35 and it will be removed one day.
This is not trivial because current code uses hard coded 32 instead of
IRQF_DISABLED in the request_irq call.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For MMC_BUS_WIDTH_8 case, current code missed setting BM_EIGHTBIT_MODE bit.
Also has a small refactor to make the code looks better in readability.
So the bit settings witch below logic:
SDMMC_BUSMODE register:
Set EIGHTBIT_MODE bit for 8 bit mode, Set FOURBIT_MODE bit for 4 bit mode.
Clear both EIGHTBIT_MODE and FOURBIT_MODE bits for 1 bit mode.
SDMMC_EXTCTRL register:
Set EXT_EIGHTBIT bit for 8 bit mode, Clear EXT_EIGHTBIT bit for 1/4 bit mode.
Add define for EXT_EIGHTBIT to avoid using magic number.
BM_ONEBIT_MASK is no longer used, thus remove it.
This patch is untested due to lack of platform with 8-bit hardware.
However since the code is there, it's good to make the code match the document.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The initialization of some SD-cards fails because the card never
leaves the busy state. Aid trouble shooting by indicating this in the
kernel log.
Signed-off-by: Johan Rudholm <johanru@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
version.h inclusion is not needed as suggested by versioncheck.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The am335x can't detect pending cirq in PM runtime suspend.
This patch reconfigures dat1 as a GPIO before going to suspend.
SDIO interrupts are detected with the GPIO, the GPIO will only wake
the module from suspend, SDIO irq detection will still happen through the
IP block.
Idea of remuxing the pins by Tony Lindgren. Code contributions from
Tony Lindgren and Balaji T K <balajitk@ti.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
These are predefined states of the driver model. When not present,
as if not set in the device tree, they become no-ops.
Explicitly selecting the default state is not needed since the
device core layer sets pin mux to "default" state before probe.
This is not the simplest implementation, on AM335x at least, we could
switch to idle at any point in the suspend hook, only the default state
needs to be set before writing to the irq registers or an IRQ might get
lost.
Acked-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On multicores, an sdio irq handler could be running in parallel to
runtime suspend. In the worst case it could be waiting for the spinlock
held by the runtime suspend. When runtime suspend is complete and the
functional clock (fclk) turned off, the irq handler will continue and
cause a SIGBUS on the first register access.
Acked-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To detect sdio irqs properly without spurious events,
OMAP4 needs IWE in CON and CTPL, CLKEXTFREE in HCTL to be set
Tested-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add SDIO IRQ entries to debugfs entry. Note that PSTATE shows current
state of data lines, incl. SDIO IRQ pending
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There have been various patches floating around for enabling
the SDIO IRQ for hsmmc, but none of them ever got merged.
Probably the reason for not merging the SDIO interrupt patches
has been the lack of wake-up path for SDIO on some omaps that
has also needed remuxing the SDIO DAT1 line to a GPIO making
the patches complex.
This patch adds the minimal SDIO IRQ support to hsmmc for
omaps that do have the wake-up path. For those omaps, the
DAT1 line need to have the wake-up enable bit set, and the
wake-up interrupt is the same as for the MMC controller.
This patch has been tested on am3730 es1.2 with mwifiex
connected to MMC3 with mwifiex waking to Ethernet traffic
from off-idle mode. Note that for omaps that do not have
the SDIO wake-up path, this patch will not work for idle
modes and further patches for remuxing DAT1 to GPIO are
needed.
Based on earlier patches [1][2] by David Vrabel
<david.vrabel@csr.com>, Steve Sakoman <steve@sakoman.com>
For now, only support SDIO interrupt if we are booted with
a separate wake-irq configued via device tree. This is
because omaps need the wake-irq for idle states, and some
omaps need special quirks. And we don't want to add new
legacy mux platform init code callbacks any longer as we
are moving to DT based booting anyways.
To use it, you need to specify the wake-irq using the
interrupts-extended property.
[1] http://www.sakoman.com/cgi-bin/gitweb.cgi?p=linux.git;a=commitdiff_plain;h=010810d22f6f49ac03da4ba384969432e0320453
[2] http://comments.gmane.org/gmane.linux.kernel.mmc/20446
Acked-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no need for an output like this:
> mmcblk mmc1:0001: calling add_quirk_mmc+0x0/0x20
Instead use this one:
> mmcblk mmc1:0001: calling add_quirk_mmc
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove the error path items that are no longer needed. The mmc card-detect
code cleans up after itself (and registers with devm) and the host error
is the same as the clock disable.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The pm_runtime call should implicitly disable the device once the
probe is over if there is no explicit reference gained. There is no
need to call pm_runtime_suspend() before the pm_runtime_disable()
call.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use devm_request_threaded_irq() for the host interrupt handlers so we
do not have to worry about freeing them on exit or error. Tidies up the
exit path code for the driver.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use the devm_clk_get() code to get the clock and allow it to be freed
automatically on release.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Start tidying the probe/release code by using devm_ioremap_resource() to
map the IO registers.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Change the initial print to show chip version and the bus rate it is
working at instead of the driver version. This is more useful information
as we already know which driver version from the kernel it is in.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove those unused ret variables to make it obvious that these function
will not return any errors in the current implementation.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Switch the common SDHCI code over to use mmc_host's regulator pointers
and remove the ones in the sdhci_host structure. Additionally, use the
common mmc_regulator_get_supply function to get the regulators and set
the ocr_avail mask.
This change sets the ocr_avail directly based upon the voltage ranges
supported which ensures ocr_avail is set correctly while allowing the
use of regulators that can't provide exactly 1.8v, 3.0v, or 3.3v.
Signed-off-by: Tim Kryger <tim.kryger@gmail.com>
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The runtime PM core handles a runtime_idle callback set to NULL as one
returning 0. So, let's just set it to NULL instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
This patch adds a fake Qualcomm ID 0x00051180 to the amba_ids, as Qualcomm
SDCC controller is pl180, but amba id registers read 0x0's.
The plan is to remove SDCC driver totally and use mmci as the main SD
controller driver for Qualcomm SOCs.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MCIFIFOCNT register behaviour on Qcom chips is very different than the other
pl180 integrations. MCIFIFOCNT register contains the number of
words that are still waiting to be transferred through the FIFO. It keeps
decrementing once the host CPU reads the MCIFIFO. With the existing logic and
the MCIFIFOCNT behaviour, mmci_pio_read will loop forever, as the FIFOCNT
register will always return transfer size before reading the FIFO.
Also the data sheet states that "This register is only useful for debug
purposes and should not be used for normal operation since it does not reflect
data which may or may not be in the pipeline".
This patch implements a qcom specific get_rx_fifocnt function which is
implemented based on status register flags. Based on qcom_fifo flag in
variant data structure, the corresponding get_rx_fifocnt function is selected.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On Controllers like Qcom SD card controller where cclk is mclk and mclk should
be directly controlled by the driver.
This patch adds support to control mclk directly in the driver, and also
adds explicit_mclk_control flag in variant structure giving more flexibility
to the driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
[Ulf Hansson] Fixed checkpatch warning
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some of the controller have maximum supported frequency, This patch adds
support in variant data structure to specify such restrictions. This
gives more flexibility in calculating the f_max before passing it to
mmc-core.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On some SOCs like Qcom there are explicit bits in the command register
to specify if its a data transfer command or not. So this patch adds
support to such bits in variant data, giving more flexibility to the
driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds edge support for data and command out to variant structure
giving more flexibility to the driver to support more SOCs which have
different clock register layout.
Without this patch other new SOCs like Qcom will have to add more code to
special case them
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
[Ulf Hansson] Resolved conflict
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds 8bit bus enable to variant structure giving more flexibility
to the driver to support more SOCs which have different clock register layout.
Without this patch other new SOCs like Qcom will have to add more code
to special case them.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
[Ulf Hansson] Resolved conflict
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds ddrmode mask to variant structure giving more flexibility
to the driver to support more SOCs which have different datactrl register
layout.
Without this patch datactrl register is updated with incorrect ddrmode mask,
resulting in failures on Qualcomm SD Card Controller.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
[Ulf Hansson] Resolved conflict
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instance of this IP on Qualcomm's SOCs has bit different layout for datactrl
register. Bit position datactrl[16:4] hold the true block size instead of power
of 2.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On Qcom SD Card controller POWER, CLKCTRL, DATACTRL and COMMAND registers
should be updated in MCLK domain, and writes to these registers must be
separated by three MCLK cycles. This resitriction is not applicable for
other registers. Any subsequent writes to these register will be ignored
until 3 MCLK have passed.
One usec delay between two CMD register writes is not sufficient in the
card identification phase where the CCLK is very low. This patch replaces
a static 1 usec delay to use mmci_reg_delay function which can provide
correct delay depending on the cclk frequency.
Without this patch the card is not detected.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a Qualcomm SD Card controller specific register variations
to header file. Qualcomm SDCC controller is pl180, with slight changes in
the register layout from standard pl180 register set.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch replaces a constant used in calculating timeout with a proper
macro. This is make code more readable.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull networking updates from David Miller:
1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov.
2) Multiqueue support in xen-netback and xen-netfront, from Andrew J
Benniston.
3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn
Mork.
4) BPF now has a "random" opcode, from Chema Gonzalez.
5) Add more BPF documentation and improve test framework, from Daniel
Borkmann.
6) Support TCP fastopen over ipv6, from Daniel Lee.
7) Add software TSO helper functions and use them to support software
TSO in mvneta and mv643xx_eth drivers. From Ezequiel Garcia.
8) Support software TSO in fec driver too, from Nimrod Andy.
9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli.
10) Handle broadcasts more gracefully over macvlan when there are large
numbers of interfaces configured, from Herbert Xu.
11) Allow more control over fwmark used for non-socket based responses,
from Lorenzo Colitti.
12) Do TCP congestion window limiting based upon measurements, from Neal
Cardwell.
13) Support busy polling in SCTP, from Neal Horman.
14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru.
15) Bridge promisc mode handling improvements from Vlad Yasevich.
16) Don't use inetpeer entries to implement ID generation any more, it
performs poorly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
rtnetlink: fix userspace API breakage for iproute2 < v3.9.0
tcp: fixing TLP's FIN recovery
net: fec: Add software TSO support
net: fec: Add Scatter/gather support
net: fec: Increase buffer descriptor entry number
net: fec: Factorize feature setting
net: fec: Enable IP header hardware checksum
net: fec: Factorize the .xmit transmit function
bridge: fix compile error when compiling without IPv6 support
bridge: fix smatch warning / potential null pointer dereference
via-rhine: fix full-duplex with autoneg disable
bnx2x: Enlarge the dorq threshold for VFs
bnx2x: Check for UNDI in uncommon branch
bnx2x: Fix 1G-baseT link
bnx2x: Fix link for KR with swapped polarity lane
sctp: Fix sk_ack_backlog wrap-around problem
net/core: Add VF link state control policy
net/fsl: xgmac_mdio is dependent on OF_MDIO
net/fsl: Make xgmac_mdio read error message useful
net_sched: drr: warn when qdisc is not work conserving
...
We have a number of front-end drivers for SDHCI_PLTFM, some of them
use 'select MMC_SDHCI_PLTFM', others use 'depends on'. This is
inconsistent and confusing, and in one case has also led to a
build error because of incomplete dependencies:
warning: (MMC_SDHCI_PXAV3 && MMC_SDHCI_PXAV2 && MMC_SDHCI_BCM_KONA) selects MMC_SDHCI_PLTFM which has unmet direct dependencies (MMC && MMC_SDHCI)
drivers/built-in.o: In function `sdhci_sirf_resume':
:(.text+0xaaacb4): undefined reference to `sdhci_resume_host'
drivers/built-in.o: In function `sdhci_sirf_suspend':
:(.text+0xaaacf8): undefined reference to `sdhci_suspend_host'
drivers/built-in.o: In function `sdhci_sirf_probe':
:(.text+0xaaaf44): undefined reference to `sdhci_add_host'
:(.text+0xaaaf50): undefined reference to `sdhci_remove_host'
This changes Kconfig to use 'depends on MMC_SDHCI_PLTFM' for all these
cases, to fix the build error and make the logic more logical.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMC host driver should not select the pmic driver, since that
may have other dependencies, notably i2c in this case. It's not
clear what the exact requirement of the driver is, but to preserve
the behavior, this patch changes the 'select' into 'depends on',
meaning you now have to turn on TPS65010 explicitly and then
MMC_OMAP.
Found during randconfig build testing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: linux-omap@vger.kernel.org
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
gcc correctly points out that hw_state can be used uninitially
in the mvsd_setup_data() function. This rearranges the function
to ensure it always contains a proper value.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Chris Ball <chris@printf.net>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: linux-mmc@vger.kernel.org
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This avoids a build error due to the use of flush_dcache_page.
drivers/mmc/host/atmel-mci.c: In function 'atmci_read_data_pio':
drivers/mmc/host/atmel-mci.c:1870:5: error: implicit declaration of function 'flush_dcache_page' [-Werror=implicit-function-declaration]
flush_dcache_page(sg_page(sg));
^
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci core was refactored recently and some of those
refactorings required changes in every sdhci platform driver.
Those updates happened around the same time as when the msm
driver was merged so the refactorings missed the msm driver.
Hook in the basic library functions so that we can boot apq8074
dragonboards again instead of crashing when we try to jump to
NULL function pointers.
Reported-by: Kevin Hilman <khilman@linaro.org>
Cc: Georgi Djakov <gdjakov@mm-sol.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Kumar Gala <galak@codeaurora.org>
Reviewed-by: Georgi Djakov <gdjakov@mm-sol.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix a number of wrong print formats.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Core:
- support HS400 mode of eMMC 5.0, via DT bindings mmc-hs400-1_{2,8}v
- if card init at 3.3v doesn't work, try 1.8v and 1.2v too
Drivers:
- moxart: New driver for MOXA ART SoCs
- rtsx_usb_sdmmc: New driver for Realtek USB card readers
- sdhci: Large rework around IRQ/regulator handling, remove card_tasklet
- sdhci-pci-o2micro: Add SeaBird SeaEagle SD3 support
- sunxi: New driver for Allwinner sunxi SoCs
- usdhi6rol0: New driver for Renesas SD/SDIO controller
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OZao
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC update from Chris Ball:
"MMC highlights for 3.16:
Core:
- support HS400 mode of eMMC 5.0, via DT bindings mmc-hs400-1_{2,8}v
- if card init at 3.3v doesn't work, try 1.8v and 1.2v too
Drivers:
- moxart: New driver for MOXA ART SoCs
- rtsx_usb_sdmmc: New driver for Realtek USB card readers
- sdhci: Large rework around IRQ/regulator handling, remove card_tasklet
- sdhci-pci-o2micro: Add SeaBird SeaEagle SD3 support
- sunxi: New driver for Allwinner sunxi SoCs
- usdhi6rol0: New driver for Renesas SD/SDIO controller"
* tag 'mmc-updates-for-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (95 commits)
mmc: sdhci-s3c: use mmc_of_parse and remove the card_tasklet
mmc: add a driver for the Renesas usdhi6rol0 SD/SDIO host controller
mmc: sdhci-of-esdhc: Fixup compile error
mmc: tegra: fix reporting of base clock frequency
mmc: tegra: disable UHS modes
mmc: sdhci-dove: use mmc_of_parse() and remove card_tasklet CD handler
MAINTAINERS: mmc: Add path to git tree
mmc: dove: fix missing MACH_DOVE dependency
mmc: sdhci: SD tuning is broken for some controllers
mmc: sdhci-esdhc-imx: fix mmc ddr mode regression issue
mmc: sdhci-pci-o2micro: Add SeaBird SeaEagle SD3 support
mmc: omap_hsmmc: split omap-dma header file
mmc: omap_hsmmc: fix cmd23 multiblock read/write
mmc: omap_hsmmc: use devm_ioremap_resource
mmc: omap_hsmmc: use devm_request_threaded_irq
mmc: omap_hsmmc: use devm_request_irq
mmc: omap_hsmmc: use devm_clk_get
mmc: sunxi: Add driver for SD/MMC hosts found on Allwinner sunxi SoCs
mmc: wmt-sdmmc: Use GFP_KERNEL instead of hard-coded value
mmc: omap: Use DIV_ROUND_UP instead of open coded
...
driver additions and fixes. There are additions to the clock core code
for some of the basic types (e.g. the common divider type has some fixes
and featured added to it).
One minor annoyance is a last-minute dependency that wasn't handled
quite right. ba0fae3 in this pull request depends on
include/dt-bindings/clock/berlin2.h, which is already in your tree via
the arm-soc pull request. Building for the berlin platform will break
when the clk tree is built on it's own, but merged into your master
branch everything should be fine.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=2AAL
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.16' of git://git.linaro.org/people/mike.turquette/linux into next
Pull clock framework updates from Mike Turquette:
"The clock framework changes for 3.16 are pretty typical: mostly clock
driver additions and fixes. There are additions to the clock core
code for some of the basic types (e.g. the common divider type has
some fixes and featured added to it).
One minor annoyance is a last-minute dependency that wasn't handled
quite right. Commit ba0fae3b06 ("clk: berlin: add core clock driver
for BG2/BG2CD") in this pull request depends on
include/dt-bindings/clock/berlin2.h, which is already in your tree via
the arm-soc pull request. Building for the berlin platform will break
when the clk tree is built on it's own, but merged into your master
branch everything should be fine"
* tag 'clk-for-linus-3.16' of git://git.linaro.org/people/mike.turquette/linux: (75 commits)
mmc: sunxi: Add driver for SD/MMC hosts found on Allwinner sunxi SoCs
clk: export __clk_round_rate for providers
clk: versatile: free icst on error return
clk: qcom: Return error pointers for unimplemented clocks
clk: qcom: Support msm8974pro global clock control hardware
clk: qcom: Properly support display clocks on msm8974
clk: qcom: Support display RCG clocks
clk: qcom: Return highest rate when round_rate() exceeds plan
clk: qcom: Fix mmcc-8974's PLL configurations
clk: qcom: Fix clk_rcg2_is_enabled() check
clk: berlin: add core clock driver for BG2Q
clk: berlin: add core clock driver for BG2/BG2CD
clk: berlin: add driver for BG2x complex divider cells
clk: berlin: add driver for BG2x simple PLLs
clk: berlin: add driver for BG2x audio/video PLL
clk: st: Terminate of match table
clk/exynos4: Fix compilation warning
ARM: shmobile: r8a7779: Add clock index macros for DT sources
clk: divider: Fix overflow in clk_divider_bestdiv
clk: u300: Terminate of match table
...
Fix the compile error.
(Removed the card_tasklet at "mmc: sdhci: push card_tasklet into treaded irq handler")
drivers/mmc/host/sdhci-s3c.c: In function ‘sdhci_s3c_notify_change’:
drivers/mmc/host/sdhci-s3c.c:402:25: error: ‘struct sdhci_host’ has no member named ‘card_tasklet’
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
The Allwinner sunxi mmc host uses dma in bus-master mode using a built-in
designware idmac controller, which is identical to the one found in the mmc-dw
hosts. However the rest of the host is not identical to mmc-dw, it deals with
sending stop commands in hardware which makes it significantly different
from the mmc-dw devices.
Signed-off-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch>
[hdegoede@redhat.com: various cleanups and fixes]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Chris Ball <chris@printf.net>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch adds a driver for the Renesas usdhi6rol0 SD/SDIO host controller
in both PIO and DMA modes.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Chris Ball <chris@printf.net>
- Put the device into low power state at system suspend.
- Convert to the common mmc DT parser.
- Add missing DT bindings needed for ux500.
Updates for ARM ux500|u300:
- Convert to the common mmc DT bindings.
- Remove redundant board file for mmci platform data.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=09ec
-----END PGP SIGNATURE-----
Merge tag 'mmc-v3.16-1' of git://git.linaro.org/people/ulf.hansson/mmc into next
Pull MMC update from Ulf Hansson:
"These patches are mainly updates for the mmci driver and have been
tested in linux-next.
Some ARM SoC related patches are also included and those have been
acked from the corresponding maintainers to go through my mmc tree.
Updates for mmci driver:
- Put the device into low power state at system suspend.
- Convert to the common mmc DT parser.
- Add missing DT bindings needed for ux500.
Updates for ARM ux500|u300:
- Convert to the common mmc DT bindings.
- Remove redundant board file for mmci platform data"
* tag 'mmc-v3.16-1' of git://git.linaro.org/people/ulf.hansson/mmc: (22 commits)
mmc: mmci: Enforce DMA configuration through DT
mmc: mmci: Enforce max frequency configuration through DT
mmc: mmci: Enforce mmc capabilities through DT
mmc: mmci: Enforce DT for signal direction and feedback clock
ARM: ux500: Remove redundant board file for mmci platform data
ARM: ux500: Add a vmmc regulator through DT for the poped eMMC for href
ARM: ux500: Add the mmc capabilities flags to DT
mmc: mmci: Enable MMC_CAP_CMD23
mmc: mmci: Mark the DT bindings for highspeed mode as deprecated
ARM: u300: Convert to the common mmc DT bindings for highspeed mode
ARM: nomadik: Convert to the common mmc DT bindings for highspeed mode
ARM: ux500: Convert to the common mmc DT bindings for highspeed mode
ARM: ux500: Add mmci signal directions and feeback clock in DT for href
mmc: mmci: Use the common mmc DT parser
mmc: mmci: Add DT bindings for feedback clock pin
mmc: mmci: Add DT bindings for signal direction
mmc: mmci: Update DT documentation
mmc: mmci: Convert to devm functions
mmc: mmci: Convert to the mmc gpio API
mmc: mmci: Put the device into low power state at system suspend
...
Remove the option to provide DMA configuration as platform data,
enforce it through DT.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tegra SDHCI controllers, by default, report a base clock frequency of
208Mhz in SDHCI_CAPABILTIES which may or may not be equal to the actual
base clock frequency. This is because the clock rate is configured by
the clock controller, which is external to the SD/MMC controller. Since
the SD/MMC controller has no knowledge of how this clock is configured,
it will simply report the maximum frequency. While the reported value
can be overridden by setting BASE_CLK_FREQ in VENDOR_CLOCK_CTRL on
Tegra30 and later SoCs, just set CAP_CLOCK_BASE_BROKEN and supply
sdhci_pltfm_clk_get_max_clock(), which simply does a clk_get_rate(),
as the get_max_clock() callback.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Program TEGRA_SDHCI_VENDOR_MISC_CTRL so that UHS modes aren't advertised
in SDHCI_CAPABILITIES_1. While the Tegra SDHCI controller does support
these modes, they require Tegra-specific tuning and calibration routines
which the driver does not support yet.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
f8ec589b86 ("mmc: sdhci-dove: allow GPIOs to be used for card detection
on Dove" added a gpio based card detect interrupt handler that was hooked
up into card_tasket.
3560db8e24 ("mmc: sdhci: push card_tasklet into threaded irq handler")
now removed that very card_tasklet causing sdhci-dove to fail on build
with:
drivers/mmc/host/sdhci-dove.c: In function 'sdhci_dove_carddetect_irq':
drivers/mmc/host/sdhci-dove.c:42:24: error: 'struct sdhci_host' has no member named 'card_tasklet'
To fix both the build error and get a working gpio card detection without
card_tasklet, replace sdhci_get_of_property() with more recent
mmc_of_parse(). It takes care of gpio-based card detect passed through DT
already and allows to remove the offending code sections dealing with
removed card_tasklet.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
DT-enabled Dove moved over from ARCH_DOVE in mach-dove to MACH_DOVE in
mach-mvebu. As non-DT ARCH_DOVE will stay to rot for a while, add a new
DT-only MACH_DOVE Kconfig. This slipped through the cracks and now is
a fix to allow to build Dove's SDHCI driver for mach-mvebu on v3.15-rc.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Riku Voipio <riku.voipio@iki.fi>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
The SD Host Controller spec states that the SD Host Controller can
request that the driver send up to 40 CMD19's while doing tuning
and that the total time the card spends responding must be < 150ms.
The sdhci_execute_tuning() function in sdhci.c that loops through
sending the CMD19's has multiple bugs. First it sets a "timeout"
variable to 150 and a loop counter variable to 40. It then decrements
both variables by 1 at the end of each loop. It tries to handle
violations of the count and time by doing a break when BOTH variables
are equal to zero, which can never happen because they we set to
different values and decremented by 1 at the same time. The timeout
variable is not based on time at all and is totally useless.
The routine also considers a loop counter of zero to be an error
which means that any controller that requests the max of 40 CMD19s
will cause tuning to fail and be disabled.
I've fixed these issues by allowing up to 40 CMD19's and I've removed
any attempt to handle the 150ms time limit. Removing timeout checking
seems safe here because each CMD19 is timeout protected and the max
loop counters insures we don't loop forever. Adding timeout checking
would not be as simple as snapping the time at the loop start and
checking for 150ms to pass because the loop queues the CMD19's and
uses events to wait for completion so the time would include
all the normal scheduler latencies.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Add O2Micro/BayHubTech chip 8520 subversion B1 SD3.0 support.
Add O2Micro/BayHubTech chip 8620 and 8621 SD3.0 support
Enable Led function of 8520 chip.
Signed-off-by: Peter Guo <peter.guo@bayhubtech.com>
Signed-off-by: Adam Lee <adam.lee@canonical.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
moving dmaengine consumer specific function to omap-dmaengine.h
to Resolve build failure seen with sh-allmodconfig:
include/linux/omap-dma.h:171:8: error: expected identifier before numeric constant
make[4]: *** [drivers/mmc/host/omap_hsmmc.o] Error 1
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Check for set block count command fails always since host->cmd is set
to NULL in the same function incorrectly. Correct host->cmd usage properly.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
With devm_ioremap_resource conversion release_mem_region, iounmap can be
removed in clean up path
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
With devm_request_threaded_irq conversion free_irq can be removed
in clean up path
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
With devm_request_irq conversion free_irq can be removed in clean up path
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
With devm_clk_get conversion clk_put can be removed in clean up path
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
The Allwinner sunxi mmc host uses dma in bus-master mode using a built-in
designware idmac controller, which is identical to the one found in the
mmc-dw hosts. However the rest of the host is not identical to mmc-dw, it
deals with sending stop commands in hardware which makes it significantly
different from the mmc-dw devices.
Signed-off-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch>
[hdegoede@redhat.com: various cleanups and fixes]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Also uses NSEC_PER_SEC and USEC_PER_SEC instead of hard-coded value.
This makes the intention more clear.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Data errors are completely expected during tuning. Printing them out
is confusing people looking at the kernel logs. They see things like:
[ 3.613296] dwmmc_exynos 12200000.dwmmc0: data error, status 0x00000088
...and they think something is wrong with their hardware.
Remove the printouts. We'll leave it up to a higher level to report
about errors.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Track whether preset mode is currently enabled in hardware, and use that
when making decisions elsewhere in the code rather than reading the
register and checking the bit.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Move the remaining parts of the power handling in sdhci_do_set_ios()
into sdhci_set_power().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Move the regulator handling into sdhci_set_power() rather than being in
sdhci_do_set_ios(). This wraps all power control up into this function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
sdhci-tegra provides a get_ro method, which overrides the checking
of the write protect bit in the PRESENT_STATE register in sdhci.c:
if (host->flags & SDHCI_DEVICE_DEAD)
is_readonly = 0;
else if (host->ops->get_ro)
is_readonly = host->ops->get_ro(host);
else
is_readonly = !(sdhci_readl(host, SDHCI_PRESENT_STATE)
& SDHCI_WRITE_PROTECT);
This means it's pointless detecting accesses to this register and
manually setting the SDHCI_WRITE_PROTECT as it has no effect.
This means that the whole of tegra_sdhci_readl() can be removed and
we can use the builtin sdhci readl functionality here.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
The only user (sdhci-of-esdhc) no longer uses these callbacks, so lets
remove them to discourage any further use.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
We don't need these hooks in order to insert code in these paths, we
can just provide our own handlers and call the main sdhci handlers as
appropriate.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
We no longer need to emulate the uhs_mode field of the host control2
register - the main sdhci driver never reads this back to evaluate
the current mode as it caches the current mode instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Clean up the code in sdhci_execute_tuning() so the decision whether
to execute tuning is clearer - and despite this reflecting what the
original code was doing, it shows that it may not be what the author
actually intended.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Rather than reading back the timing information from the registers,
cache it locally. This allows implementations to translate the UHS
timing by overriding the set_uhs_signaling() method as required
without also having to emulate the SDHCI_HOST_CONTROL2 register.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
[Ulf Hansson] Resolved conflict
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Add sdhci_set_uhs_signaling() and always call the set_uhs_signaling
method. This avoids quirks being added into sdhci_set_uhs_signaling().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
[Ulf Hansson] Resolved conflict
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
The set_uhs_signaling() method gives the impression that it can fail,
but anything returned from the method is entirely ignored by the sdhci
driver. So returning failure has no effect.
So, kill the idea that it's possible for this to return an error by
removing the returned value.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
It is far from obvious what this is doing, and it looks like it's an
unbalanced runtime_pm_get() call. However, the put is inside
sdhci_tasklet_finish(), so it's not unbalanced at all. This should
be documented so people know what's going on here. Do so.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
sdhci-esdhc-imx tries to DMA to the kernel stack when tuning the
interface, which causes dma-debug to complain. Fix this by kmallocing
a buffer to hold the received tuning pattern.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Move the setting of mmc->actual_clock to zero into the set_clock
handlers themselves. This will allow us to clean up the calling
logic for the set_clock() method, and turn sdhci_set_clock() into
a library function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
We don't need implementations to do this, since the only time it's
necessary is when we change the clock, and the only place that happens
is in sdhci_do_set_ios(). So, move it there, and remove it from the
iMX platform backend.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Only one caller to sdhci_set_clock() needs to check whether the
requested clock frequency was the same as the currently set frequency,
yet we work around this in several other sites via sdhci_update_clock().
Rather than doing this, move those checks out into sdhci_do_set_ios(),
which then allows sdhci_update_clock() to be eliminated.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Rather than using the streaming API, use the coherent allocator to
provide this memory, thereby eliminating cache flushing of it each
time we map and unmap it. This results in a 7.5% increase in
transfer speed with a UHS-1 card operating in 3.3v mode at a clock
of 49.5MHz.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
On read, we don't need to sync the whole scatterlist and then check
whether any segments need copying - if we check first, we avoid
potentially expensive cache handling.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
The Freescale esdhc driver is the only driver which needs the interrupt
registers restored after a reset. Move this quirk to be part of the
ESDHC driver implementation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Rather than having platform_reset_enter/platform_reset_exit methods,
turn the core of the reset handling into a library function which
platforms can call at the appropriate moment in their (new) reset
method.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
When we disable card detection interrupts, we should disable both the
insert and remove interrupts irrespective of the current state - this
avoids races between the hardware card detect changing state before
we've read that updated state and altered the interrupt mask.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Rather than wasting cycles read-modify-writing the interrupt enable
registers, cache the value locally instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Allow SDIO interrupts to be received while the SDHCI host is runtime
suspended. We do this by leaving the AHB clock enabled while the
host is runtime suspended so we can access the SDHCI registers, and
so read and raise the SDIO card interrupt.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
There's no requirement to have the card tasklet separate now that we
have a threaded interrupt handler, so kill this and move the called
code into the threaded part of the handler.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Use a generic threaded interrupt handler for SDIO interrupt handling,
rather than allowing the SDIO core code to buggily spawn its own
thread. This results in host drivers to be more in control of how
SDIO interrupts are acknowledged in the hardware, rather than having
the internals of the SDIO core placed upon them, possibly resulting
in sub-standard handling.
At least one SDHCI implementation specifies a very specific sequence
to deal with a card interrupt.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
