We enabled write-combining for memory-mapped registers in commit
65f0b417de, but inhibited it for the
MCDI shared memory where this is not supported. However,
write-combining mappings also allow read-reordering, which may also
be a problem.
I found that when an SFC9000-family controller is connected to an
Intel 3000 chipset, and write-combining is enabled, the controller
stops responding to PCIe read requests during driver initialisation
while the driver is polling for completion of an MCDI command. This
results in an NMI and system hang. Adding read memory barriers
between all reads to the shared memory area appears to reduce but not
eliminate the probability of this.
We have not yet established whether this is a bug in our BIU or in the
PCIe bridge. For now, work around by mapping the shared memory area
separately.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
btrfs scrub - make fixups sync, don't reuse fixup bios
Fixups are already sync for csum failures, this patch makes them sync
for EIO case as well.
Fixups are now sharing pages with the parent sbio - instead of
allocating a separate page to do a fixup we grab the page from the sbio
buffer.
Fixup bios are no longer reused.
struct fixup is no longer needed, instead pass [sbio pointer, index].
Originally this was added to look at the possibility of sharing the code
between drive swap and scrub, but it actually fixes a serious bug in
scrub code where errors that could be corrected were ignored and
reported as uncorrectable.
btrfs scrub - restore bios properly after media errors
The current code reallocates a bio after a media error. This is a
temporary measure introduced in v3 after a serious problem related to
bio reuse was found in v2 of scrub patchset.
Basically we did not reset bv_offset and bv_len fields of the bio_vec
structure. They are changed in case I/O error happens, for example, at
offset 512 or 1024 into the page. Also bi_flags field wasn't properly
setup before reusing the bio.
Signed-off-by: Arne Jansen <sensille@gmx.net>
adds ioctls necessary to start and cancel scrubs, to get current
progress and to get info about devices to be scrubbed.
Note that the scrub is done per-device and that the ioctl only
returns after the scrub for this devices is finished or has been
canceled.
Signed-off-by: Arne Jansen <sensille@gmx.net>
This adds an initial implementation for scrub. It works quite
straightforward. The usermode issues an ioctl for each device in the
fs. For each device, it enumerates the allocated device chunks. For
each chunk, the contained extents are enumerated and the data checksums
fetched. The extents are read sequentially and the checksums verified.
If an error occurs (checksum or EIO), a good copy is searched for. If
one is found, the bad copy will be rewritten.
All enumerations happen from the commit roots. During a transaction
commit, the scrubs get paused and afterwards continue from the new
roots.
This commit is based on the series originally posted to linux-btrfs
with some improvements that resulted from comments from David Sterba,
Ilya Dryomov and Jan Schmidt.
Signed-off-by: Arne Jansen <sensille@gmx.net>
Since mandatory barriers may be used (explicitly or implicitly via readl
etc.) to ensure the ordering between Device and Normal memory accesses,
a DMB is not enough. This patch converts it to a DSB.
Cc: Colin Cross <ccross@android.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
GDB's interrupt.exp test cases currenly fail on ARM. The problem is how do_signal
handled restarting interrupted system calls:
The entry.S assembler code determines that we come from a system call; and that
information is passed as "syscall" parameter to do_signal. That routine then
calls get_signal_to_deliver [*] and if a signal is to be delivered, calls into
handle_signal. If a system call is to be restarted either after the signal
handler returns, or if no handler is to be called in the first place, the PC
is updated after the get_signal_to_deliver call, either in handle_signal (if
we have a handler) or at the end of do_signal (otherwise).
Now the problem is that during [*], the call to get_signal_to_deliver, a ptrace
intercept may happen. During this intercept, the debugger may change registers,
including the PC. This is done by GDB if it wants to execute an "inferior call",
i.e. the execution of some code in the debugged program triggered by GDB.
To this purpose, GDB will save all registers, allocate a stack frame, set up
PC and arguments as appropriate for the call, and point the link register to
a dummy breakpoint instruction. Once the process is restarted, it will execute
the call and then trap back to the debugger, at which point GDB will restore
all registers and continue original execution.
This generally works fine. However, now consider what happens when GDB attempts
to do exactly that while the process was interrupted during execution of a to-be-
restarted system call: do_signal is called with the syscall flag set; it calls
get_signal_to_deliver, at which point the debugger takes over and changes the PC
to point to a completely different place. Now get_signal_to_deliver returns
without a signal to deliver; but now do_signal decides it should be restarting
a system call, and decrements the PC by 2 or 4 -- so it now points to 2 or 4
bytes before the function GDB wants to call -- which leads to a subsequent crash.
To fix this problem, two things need to be supported:
- do_signal must be able to recognize that get_signal_to_deliver changed the PC
to a different location, and skip the restart-syscall sequence
- once the debugger has restored all registers at the end of the inferior call
sequence, do_signal must recognize that *now* it needs to restart the pending
system call, even though it was now entered from a breakpoint instead of an
actual svc instruction
This set of issues is solved on other platforms, usually by one of two
mechanisms:
- The status information "do_signal is handling a system call that may need
restarting" is itself carried in some register that can be accessed via
ptrace. This is e.g. on Intel the "orig_eax" register; on Sparc the kernel
defines a magic extra bit in the flags register for this purpose.
This allows GDB to manage that state: reset it when doing an inferior call,
and restore it after the call is finished.
- On s390, do_signal transparently handles this problem without requiring
GDB interaction, by performing system call restarting in the following
way: first, adjust the PC as necessary for restarting the call. Then,
call get_signal_to_deliver; and finally just continue execution at the
PC. This way, if GDB does not change the PC, everything is as before.
If GDB *does* change the PC, execution will simply continue there --
and once GDB restores the PC it saved at that point, it will automatically
point to the *restarted* system call. (There is the minor twist how to
handle system calls that do *not* need restarting -- do_signal will undo
the PC change in this case, after get_signal_to_deliver has returned, and
only if ptrace did not change the PC during that call.)
Because there does not appear to be any obvious register to carry the
syscall-restart information on ARM, we'd either have to introduce a new
artificial ptrace register just for that purpose, or else handle the issue
transparently like on s390. The patch below implements the second option;
using this patch makes the interrupt.exp test cases pass on ARM, with no
regression in the GDB test suite otherwise.
Cc: patches@linaro.org
Signed-off-by: Ulrich Weigand <ulrich.weigand@linaro.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The SPARSEMEM code allocates memmap entries only for sections which are
present (i.e. those which contain some valid memory). The membank checks
in free_unused_memmap do not take this into account and can incorrectly
attempt to free memory which is not allocated, resulting in a BUG() in
the bootmem code.
However, if memory is configured as follows:
|<----section---->|<----hole---->|<----section---->|
+--------+--------+--------------+--------+--------+
| bank 0 | unused | | bank 1 | unused |
+--------+--------+--------------+--------+--------+
where a bank only occupies part of a section, the memmap allocated for
the remainder of the section *can* be freed.
This patch modifies the checks in free_unused_memmap so that only valid
memmap entries are considered for removal.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When we are in the label cc_dword_align, registers %o0 and %o1 have the same last 2 bits,
but it's not guaranteed one of them is zero. So we can get unaligned memory access
in label ccte. Example of parameters which lead to this:
%o0=0x7ff183e9, %o1=0x8e709e7d, %g1=3
With the parameters I had a memory corruption, when the additional 5 bytes were rewritten.
This patch corrects the error.
One comment to the patch. We don't care about the third bit in %o1, because cc_end_cruft
stores word or less.
Signed-off-by: Tkhai Kirill <tkhai@yandex.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, writebacks may end up recursing back into the filesystem due to
GFP_KERNEL direct reclaims in the pnfs subsystem.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: do not use i_wrbuffer_ref as refcount for Fb cap
ceph: fix list_add in ceph_put_snap_realm
ceph: print debug message before put mds session
This reverts commit f21ca5fff6.
Quoth Gustavo F. Padovan:
"Commit f21ca5fff6 can cause a NULL
dereference if we call shutdown in a bluetooth SCO socket and doesn't
wait the shutdown completion to call close(). Please revert it. I
may have a fix for it soon, but we don't have time anymore, so revert
is the way to go. ;)"
Requested-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
include/linux/gfp.h and include/trace/events/gfpflags.h are out of sync.
When tracing is enabled, certain flags are not recognised and the text
output is less useful as a result. Add the missing flags.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Testing the shmem_swaplist replacements for igrab() revealed another bug:
writes to /dev/loop0 on a tmpfs file which fills its filesystem were
sometimes failing with "Buffer I/O error"s.
These came from ENOSPC failures of shmem_getpage(), when racing with
swapoff: the same could happen when racing with another shmem_getpage(),
pulling the page in from swap in between our find_lock_page() and our
taking the info->lock (though not in the single-threaded loop case).
This is unacceptable, and surprising that I've not noticed it before:
it dates back many years, but (presumably) was made a lot easier to
reproduce in 2.6.36, which sited a page preallocation in the race window.
Fix it by rechecking the page cache before settling on an ENOSPC error.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The use of igrab() in swapoff's shmem_unuse_inode() is just as vulnerable
to umount as that in shmem_writepage().
Fix this instance by extending the protection of shmem_swaplist_mutex
right across shmem_unuse_inode(): while it's on the list, the inode cannot
be evicted (and the filesystem cannot be unmounted) without
shmem_evict_inode() taking that mutex to remove it from the list.
But since shmem_writepage() might take that mutex, we should avoid making
memory allocations or memcg charges while holding it: prepare them at the
outer level in shmem_unuse(). When mem_cgroup_cache_charge() was
originally placed, we didn't know until that point that the page from swap
was actually a shmem page; but nowadays it's noted in the swap_map, so
we're safe to charge upfront. For the radix_tree, do as is done in
shmem_getpage(): preload upfront, but don't pin to the cpu; so we make a
habit of refreshing the node pool, but might dip into GFP_NOWAIT reserves
on occasion if subsequently preempted.
With the allocation and charge moved out from shmem_unuse_inode(),
we can also hold index map and info->lock over from finding the entry.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Konstanin Khlebnikov reports that a dangerous race between umount and
shmem_writepage can be reproduced by this script:
for i in {1..300} ; do
mkdir $i
while true ; do
mount -t tmpfs none $i
dd if=/dev/zero of=$i/test bs=1M count=$(($RANDOM % 100))
umount $i
done &
done
on a 6xCPU node with 8Gb RAM: kernel very unstable after this accident. =)
Kernel log:
VFS: Busy inodes after unmount of tmpfs.
Self-destruct in 5 seconds. Have a nice day...
WARNING: at lib/list_debug.c:53 __list_del_entry+0x8d/0x98()
list_del corruption. prev->next should be ffff880222fdaac8, but was (null)
Pid: 11222, comm: mount.tmpfs Not tainted 2.6.39-rc2+ #4
Call Trace:
warn_slowpath_common+0x80/0x98
warn_slowpath_fmt+0x41/0x43
__list_del_entry+0x8d/0x98
evict+0x50/0x113
iput+0x138/0x141
...
BUG: unable to handle kernel paging request at ffffffffffffffff
IP: shmem_free_blocks+0x18/0x4c
Pid: 10422, comm: dd Tainted: G W 2.6.39-rc2+ #4
Call Trace:
shmem_recalc_inode+0x61/0x66
shmem_writepage+0xba/0x1dc
pageout+0x13c/0x24c
shrink_page_list+0x28e/0x4be
shrink_inactive_list+0x21f/0x382
...
shmem_writepage() calls igrab() on the inode for the page which came from
page reclaim, to add it later into shmem_swaplist for swapoff operation.
This igrab() can race with super-block deactivating process:
shrink_inactive_list() deactivate_super()
pageout() tmpfs_fs_type->kill_sb()
shmem_writepage() kill_litter_super()
generic_shutdown_super()
evict_inodes()
igrab()
atomic_read(&inode->i_count)
skip-inode
iput()
if (!list_empty(&sb->s_inodes))
printk("VFS: Busy inodes after...
This igrap-iput pair was added in commit 1b1b32f2c6 "tmpfs: fix
shmem_swaplist races" based on incorrect assumptions: igrab() protects the
inode from concurrent eviction by deletion, but it does nothing to protect
it from concurrent unmounting, which goes ahead despite the raised
i_count.
So this use of igrab() was wrong all along, but the race made much worse
in 2.6.37 when commit 63997e98a3 "split invalidate_inodes()" replaced
two attempts at invalidate_inodes() by a single evict_inodes().
Konstantin posted a plausible patch, raising sb->s_active too: I'm unsure
whether it was correct or not; but burnt once by igrab(), I am sure that
we don't want to rely more deeply upon externals here.
Fix it by adding the inode to shmem_swaplist earlier, while the page lock
on page in page cache still secures the inode against eviction, without
artifically raising i_count. It was originally added later because
shmem_unuse_inode() is liable to remove an inode from the list while it's
unswapped; but we can guard against that by taking spinlock before
dropping mutex.
Reported-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Signed-off-by: Hugh Dickins <hughd@google.com>
Tested-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit dde79e005a ("page_cgroup: reduce allocation overhead for
page_cgroup array for CONFIG_SPARSEMEM") added a regression that the
memory cgroup data structures all end up in node 0 because the first
attempt at allocating them would not pass in a node hint. Since the
initialization runs on CPU #0 it would all end up node 0. This is a
problem on large memory systems, where node 0 would lose a lot of
memory.
Change the alloc_pages_exact() to alloc_pages_exact_nid(). This will
still fall back to other nodes if not enough memory is available.
[ RED-PEN: right now it would fall back first before trying
vmalloc_node. Probably not the best strategy ... But I left it like
that for now. ]
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Reported-by: Doug Nelson
Cc: David Rientjes <rientjes@google.com>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a alloc_pages_exact_nid() that allocates on a specific node.
The naming is quite broken, but fixing that would need a larger renaming
action.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: tweak comment]
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Cc: David Rientjes <rientjes@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Take alphabetical orders for MAINTAINERS file.
Signed-off-by: Harry Wei <harryxiyou@gmail.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The lru_deactivate_fn should not move page which in on unevictable lru
into inactive list. Otherwise, we can meet BUG when we use
isolate_lru_pages as __isolate_lru_page could return -EINVAL.
Reported-by: Ying Han <yinghan@google.com>
Tested-by: Ying Han <yinghan@google.com>
Signed-off-by: Minchan Kim <minchan.kim@gmail.com>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Reviewed-by: Rik van Riel<riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The driver is not balancing set_irq and disable_irq_wake() calls, so
ensure that it keeps track of whether the wake is enabled.
The fixes the following error on S3C6410 devices:
WARNING: at kernel/irq/manage.c:382 set_irq_wake+0x84/0xec()
Unbalanced IRQ 92 wake disable
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The SNAPSHOT_S2RAM ioctl used for implementing the feature allowing
one to suspend to RAM after creating a hibernation image is currently
broken, because it doesn't clear the "ready" flag in the struct
snapshot_data object handled by it. As a result, the
SNAPSHOT_UNFREEZE doesn't work correctly after SNAPSHOT_S2RAM has
returned and the user space hibernate task cannot thaw the other
processes as appropriate. Make SNAPSHOT_S2RAM clear data->ready
to fix this problem.
Tested-by: Alexandre Felipe Muller de Souza <alexandrefm@mandriva.com.br>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: stable@kernel.org
If the process using the hibernate user space interface closes
/dev/snapshot after creating a hibernation image without thawing
tasks, snapshot_release() should call pm_restore_gfp_mask() to
restore the GFP mask used before the creation of the image. Make
that happen.
Tested-by: Alexandre Felipe Muller de Souza <alexandrefm@mandriva.com.br>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: stable@kernel.org
A warning is printed by pm_restrict_gfp_mask() while the
SNAPSHOT_S2RAM ioctl is being executed after creating a hibernation
image, because pm_restrict_gfp_mask() has been called once already
before the image creation and suspend_devices_and_enter() calls it
once again. This happens after commit 452aa6999e
(mm/pm: force GFP_NOIO during suspend/hibernation and resume).
To avoid this issue, move pm_restrict_gfp_mask() and
pm_restore_gfp_mask() from suspend_devices_and_enter() to its caller
in kernel/power/suspend.c.
Reported-by: Alexandre Felipe Muller de Souza <alexandrefm@mandriva.com.br>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: stable@kernel.org
Prevents an infinite loop as list was never emptied.
Signed-off-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Free the slot and resend the RPC with new session <slot#,seq#>.
For nfs4_async_handle_error, return -EAGAIN and set the task->tk_status to 0
to restart the async rpc in the rpc_restart_call_prepare state which resets
the slot.
For nfs4_handle_exception, retrying a call that uses nfs4_call_sync will
reset the slot via nfs41_call_sync_prepare.
For open/close/lock/locku/delegreturn/layoutcommit/unlink/rename/write
cachethis is true, so these operations will not trigger an
NFS4ERR_RETRY_UNCACHED_REP.
Signed-off-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Commit d594f1f31a (omap: IOMMU: add
support to callback during fault handling) broke interrupt line sharing
between the OMAP3 ISP and its IOMMU. Because of this, every interrupt
generated by the OMAP3 ISP is handled by the IOMMU driver instead of
being passed to the OMAP3 ISP driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We increments i_wrbuffer_ref when taking the Fb cap. This breaks
the dirty page accounting and causes looping in
__ceph_do_pending_vmtruncate, and ceph client hangs.
This bug can be reproduced occasionally by running blogbench.
Add a new field i_wb_ref to inode and dedicate it to Fb reference
counting.
Signed-off-by: Henry C Chang <henry.cy.chang@gmail.com>
Signed-off-by: Sage Weil <sage@newdream.net>
The mds session, s, could be freed during ceph_put_mds_session.
Move dout before ceph_put_mds_session.
Signed-off-by: Henry C Chang <henry.cy.chang@gmail.com>
Signed-off-by: Sage Weil <sage@newdream.net>
Disable irqs during optimized callback, so we dont miss any in-irq kprobes.
The following commands:
# cd /debug/tracing/
# echo "p mutex_unlock" >> kprobe_events
# echo "p _raw_spin_lock" >> kprobe_events
# echo "p smp_apic_timer_interrupt" >> ./kprobe_events
# echo 1 > events/enable
Cause the optimized kprobes to be missed. None is missed
with the fix applied.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Link: http://lkml.kernel.org/r/20110511110613.GB2390@jolsa.brq.redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Only configure sleep script when the flag is TWL4030_SLEEP_SCRIPT.
Adding the missing brackets for fixing the issue.
Signed-off-by: Lesly A M <leslyam@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: David Derrick <dderrick@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fix below compile error:
CC drivers/mfd/asic3.o
drivers/mfd/asic3.c: In function 'asic3_irq_demux':
drivers/mfd/asic3.c:147: error: 'irq_data' undeclared (first use in this function)
drivers/mfd/asic3.c:147: error: (Each undeclared identifier is reported only once
drivers/mfd/asic3.c:147: error: for each function it appears in.)
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
With commit 19403165 a main part of ehci-omap.c moved to
drivers/mfd/omap-usb-host.c created by commit 17cdd29d.
Due to this reorganisation the polarity used to reset the
external USB phy changed and USB host doesn't recognize
any devices.
Signed-off-by: Juergen Kilb <J.Kilb@phytec.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The Xen changes were using DMA_ERROR_CODE which isn't defined on a few
platforms, however we reverted the Xen patch that caused use to try and
use this code path earlier in 2.6.39 cycle, so for now lets just force
the code to never take this path and allow it to build again on alpha.
The proper long term answer is probably to store if the dma_addr has
been assigned to alongside the dma_addr in the higher level code,
though I think Thomas wanted to rewrite most of this anyways properly.
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The TCC disable setup was incorrect. This
prevents the GPU from hanging when draw commands
are issued.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We are accessing totally the wrong struct in this case, and putting
uninitialised values into the GPU, which it doesn't like unsurprisingly.
Signed-off-by: Dave Airlie <airlied@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (27 commits)
slcan: fix ldisc->open retval
net/usb: mark LG VL600 LTE modem ethernet interface as WWAN
xfrm: Don't allow esn with disabled anti replay detection
xfrm: Assign the inner mode output function to the dst entry
net: dev_close() should check IFF_UP
vlan: fix GVRP at dismantle time
netfilter: revert a2361c8735
netfilter: IPv6: fix DSCP mangle code
netfilter: IPv6: initialize TOS field in REJECT target module
IPVS: init and cleanup restructuring
IPVS: Change of socket usage to enable name space exit.
netfilter: ebtables: only call xt_compat_add_offset once per rule
netfilter: fix ebtables compat support
netfilter: ctnetlink: fix timestamp support for new conntracks
pch_gbe: support ML7223 IOH
PCH_GbE : Fixed the issue of checksum judgment
PCH_GbE : Fixed the issue of collision detection
NET: slip, fix ldisc->open retval
be2net: Fixed bugs related to PVID.
ehea: fix wrongly reported speed and port
...
This reverts commit 4a5fa3590f, which did not allow SLUB to be used
on architectures that use DISCONTIGMEM without compiling NUMA support
without CONFIG_BROKEN also set.
The slub panic that it was intended to prevent is addressed by
d9b41e0b54 ("[PARISC] set memory ranges in N_NORMAL_MEMORY when
onlined") on parisc so there is no further slub issues with such a
configuration.
The reverts allows SLUB now to be used on such architectures since
there haven't been any reports of additional errors.
Cc: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
TTY layer expects 0 if the ldisc->open operation succeeded.
Reported-by: Matvejchikov Ilya <matvejchikov@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like other mobile broadband device ethernet interfaces, mark the LG
VL600 with the 'wwan' devtype so userspace knows it needs additional
configuration via the AT port before the interface can be used.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
