.recalc_rate callback for the fractional PLL doesn't take operating
mode into account when calculating PLL rate. This results in
the incorrect PLL rates when PLL is operating in integer mode.
Operating mode of fractional PLL is based on the value of the
fractional divider. Currently it assumes that the PLL will always
be configured in fractional mode which may not be
the case. This may result in the wrong output frequency.
Also vco was calculated based on the current operating mode which
makes no sense because .set_rate is setting operating mode. Instead,
vco should be calculated using PLL settings that are about to be set.
Fixes: 43049b0c83f17("CLK: Pistachio: Add PLL driver")
Cc: <stable@vger.kernel.org> # 4.1
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Zdenko Pulitika <zdenko.pulitika@imgtec.com>
Signed-off-by: Govindraj Raja <govindraj.raja@imgtec.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
PLL enable callbacks are overriding PLL mode (int/frac) and
Noise reduction (on/off) settings set by the boot loader which
results in the incorrect clock rate.
PLL mode and noise reduction are defined by the DSMPD and DACPD bits
of the PLL control register. PLL .enable() callbacks enable PLL
by deasserting all power-down bits of the PLL control register,
including DSMPD and DACPD bits, which is not necessary since
these bits don't actually enable/disable PLL.
This commit fixes the problem by removing DSMPD and DACPD bits
from the "PLL enable" mask.
Fixes: 43049b0c83f17("CLK: Pistachio: Add PLL driver")
Cc: <stable@vger.kernel.org> # 4.1
Reviewed-by: Andrew Bresitcker <abrestic@chromium.org>
Signed-off-by: Zdenko Pulitika <zdenko.pulitika@imgtec.com>
Signed-off-by: Govindraj Raja <govindraj.raja@imgtec.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This commit fixes 32bit integer overflows throughout the pll driver
(i.e. wherever the result of integer multiplication may exceed the
range of u32).
One of the functions affected by this problem is .recalc_rate. It
returns incorrect rate for some pll settings (not for all though)
which in turn results in the incorrect rate setup of pll's child
clocks.
Fixes: 43049b0c83f17("CLK: Pistachio: Add PLL driver")
Cc: <stable@vger.kernel.org> # 4.1
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Zdenko Pulitika <zdenko.pulitika@imgtec.com>
Signed-off-by: Govindraj Raja <govindraj.raja@imgtec.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Use the provider based method to get a clock's name so that we
can get rid of the clk member in struct clk_hw one day. Mostly
converted with the following coccinelle script.
@@
struct clk_hw *E;
@@
-__clk_get_name(E->clk)
+clk_hw_get_name(E)
Acked-by: Heiko Stuebner <heiko@sntech.de>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kevin Cernekee <cernekee@chromium.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
When setting the PLL rates, check that:
- VCO is within range
- PFD is within range
- PLL is disabled when postdiv is changed
- postdiv2 <= postdiv1
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Currently, when the rate is changed, the driver makes sure the
PLL is enabled before doing so. This is done because the PLL
cannot be locked while disabled. Once locked, the drivers
returns the PLL to its previous enable/disable state.
This is a bit cumbersome, and can be simplified.
This commit reworks the .set_rate() functions for the integer
and fractional PLLs. Upon rate change, the PLL is now locked
only if it's already enabled.
Also, the driver locks the PLL on .enable(). This makes sure
the PLL is locked when enabled, and not locked when disabled.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This commit adds a pll_lock() helper making the code more readable.
Cosmetic change only, no functionality changes.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add a driver for the integer (GF40LP_LAINT) and fractional (GF40LP_FRAC)
PLLs present on Pistachio.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Patchwork: https://patchwork.linux-mips.org/patch/9316/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
