When a P2P GO interface goes down, cfg80211 doesn't properly
tear it down, leading to warnings later. Add the GO interface
type to the enumeration to tear it down like AP interfaces.
Otherwise, we leave it pending and mac80211's state can get
very confused, leading to warnings later.
Cc: stable@vger.kernel.org
Reported-by: Ilan Peer <ilan.peer@intel.com>
Tested-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is similar to the race Linus had reported, but in this case
it's an older bug: nl80211_prepare_wdev_dump() uses the wiphy
index in cb->args[0] as it is and thus parses the message over
and over again instead of just once because 0 is the first valid
wiphy index. Similar code in nl80211_testmode_dump() correctly
offsets the wiphy_index by 1, do that here as well.
Cc: stable@vger.kernel.org
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The dev_attrs field of struct class is going away soon, dev_groups
should be used instead. This converts the networking wireless class
code to use the correct field.
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Cc: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current regdomain was not always set by the core. This causes
cards with a custom regulatory domain to ignore user initiated changes
if done before the card was registered.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Whether the wiphy supports it or not is already checked, so what is left
is to enable these channel types.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Mandatory rates for 5 and 10 MHz are different from the rates used for
20 MHz in 2.4 GHz mode, as they use OFDM only.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
To allow scanning and working with 5 MHz and 10 MHz BSS, extend the
inform bss commands and add wrappers to take 5 and 10 MHz bss into
account.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
In most cases, host that receives IPv4 and IPv6 multicast/broadcast
packets does not do anything with these packets. Therefore the
reception of these unwanted packets causes unnecessary processing
and power consumption.
Packet coalesce feature helps to reduce number of received
interrupts to host by buffering these packets in firmware/hardware
for some predefined time. Received interrupt will be generated when
one of the following events occur.
a) Expiration of hardware timer whose expiration time is set to
maximum coalescing delay of matching coalesce rule.
b) Coalescing buffer in hardware reaches it's limit.
c) Packet doesn't match any of the configured coalesce rules.
This patch adds set/get configuration support for packet coalesce.
User needs to configure following parameters for creating a coalesce
rule.
a) Maximum coalescing delay
b) List of packet patterns which needs to be matched
c) Condition for coalescence. pattern 'match' or 'no match'
Multiple such rules can be created.
This feature needs to be advertised during driver initialization.
Drivers are supposed to do required firmware/hardware settings based
on user configuration.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
[fix kernel-doc, change free function, fix copy/paste error]
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Currently packet patterns and it's enum/structures are used only
for WoWLAN feature. As we intend to reuse them for new feature
packet coalesce, they are renamed in this patch.
Older names are kept for backward compatibility purpose.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
RSSI threshold value used for mesh peering should be in
negative value. After range checks to mesh parameters is
introduced, this is not allowed. Fix this.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
restore_regulatory_settings() requires the RTNL to be held,
add the missing locking in reg_timeout_work().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When splitting the SME implementation from the MLME code,
I introduced a few bugs:
* association failures no longer sent a connect-failure event
* getting disassociated from the AP caused deauth to be sent
but state wasn't cleaned up, leading to warnings
* authentication failures weren't cleaned up properly, causing
new connection attempts to warn and fail
Fix these bugs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
These two events were sent to the default network
namespace.
This caused AP mode in a non-default netns to not
work correctly. Mgmt tx status was multicasted to
a different (default) netns instead of the one the
AP was in.
Cc: stable@vger.kernel.org
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The following compilation issue popped up moving from v3.10-rc1 to
v3.10-rc6 after merging wireless-testing.
net/wireless/sysfs.c:86:13: error: 'cfg80211_leave_all' defined
but not used [-Werror=unused-function]
The function is only called when CONFIG_PM is enabled. Moving the
function under CONFIG_PM as well.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If it *is* still set when the netdev is being deleted,
then we are about to leak a pointer. Warn and clean up
in that case.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Should help the next person that tries to understand
the bss refcounting logic.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/wireless/ath/ath9k/Kconfig
drivers/net/xen-netback/netback.c
net/batman-adv/bat_iv_ogm.c
net/wireless/nl80211.c
The ath9k Kconfig conflict was a change of a Kconfig option name right
next to the deletion of another option.
The xen-netback conflict was overlapping changes involving the
handling of the notify list in xen_netbk_rx_action().
Batman conflict resolution provided by Antonio Quartulli, basically
keep everything in both conflict hunks.
The nl80211 conflict is a little more involved. In 'net' we added a
dynamic memory allocation to nl80211_dump_wiphy() to fix a race that
Linus reported. Meanwhile in 'net-next' the handlers were converted
to use pre and post doit handlers which use a flag to determine
whether to hold the RTNL mutex around the operation.
However, the dump handlers to not use this logic. Instead they have
to explicitly do the locking. There were apparent bugs in the
conversion of nl80211_dump_wiphy() in that we were not dropping the
RTNL mutex in all the return paths, and it seems we very much should
be doing so. So I fixed that whilst handling the overlapping changes.
To simplify the initial returns, I take the RTNL mutex after we try
to allocate 'tb'.
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the potential issue that the BSS struct that we use
and later assign to wdev->current_bss is removed from the scan
list while associating.
Also warn when we don't have a BSS struct in connect_result
unless it's from a driver that only has the connect() API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Doing so will allow us to hold the BSS (not just ref it) over the
association process, thus ensuring that it doesn't time out and
gets invisible to the user (e.g. in 'iw wlan0 link'.)
This also fixes a leak in mac80211 where it doesn't always release
the BSS struct properly in all cases where calling this function.
This leak was reported by Ben Greear.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Avoid parsing the original dump message again and again by
allocating a small state struct that is used by the functions
involved in the dump, storing this struct in cb->args[0].
This reduces the memory allocation size as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge mac80211 to avoid conflicts with the nl80211 attrbuf
changes.
Conflicts:
net/mac80211/iface.c
net/wireless/nl80211.c
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since my commit 3713b4e364 ("nl80211: allow splitting wiphy
information in dumps"), nl80211_dump_wiphy() uses the global
nl80211_fam.attrbuf for parsing the incoming data. This wouldn't
be a problem if it only did so on the first dump iteration which
is locked against other commands in generic netlink, but due to
space constraints in cb->args (the needed state doesn't fit) I
decided to always parse the original message. That's racy though
since nl80211_fam.attrbuf could be used by some other parsing in
generic netlink concurrently.
For now, fix this by allocating a separate parse buffer (it's a
bit too big for the stack, currently 1448 bytes on 64-bit). For
-next, I'll change the code to parse into the global buffer in
the first round only and then allocate a smaller buffer to keep
the data in cb->args.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add defines for 5 and 10 MHz channel width and fix channel
handling functions accordingly.
Also check for and report the WIPHY_FLAG_SUPPORTS_5_10_MHZ
capability.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
[fix spelling in comment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
only the attributes are required and not the whole netlink info, as the
function accesses the attributes only anyway. This makes it easier to
parse nested beacon IEs later.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In two wiphy dump error cases, most often when the dump allocation
must be increased, the RTNL is leaked. This quickly results in a
complete system lockup. Release the RTNL correctly.
Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Users may want to send a frame on the current channel
without specifying it.
This is particularly useful for the correct implementation
of the IBSS/RSN support in wpa_supplicant which requires to
receive and send AUTH frames.
Make mgmt_tx pass a NULL channel to the driver if none has
been specified by the user.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
I (Johannes) accidentally applied the first version of the patch
("Allow TDLS peer AID to be configured for VHT"). Now apply just
the changes between v1 and v2 to get the AID verification and
prefer the new attribute over the old one.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently mesh uses mandatory rates as the default basic rates. Allow basic
rates to be configured during mesh join. Basic rates are applied only if
channel is also provided with mesh join command.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
[some whitespace fixes, refuse basic rates w/o channel]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a STA has a peer that it hasn't seen any tx activity
from for a certain length of time, the peer link is
expired. This means the inactive STA is removed from the
list of peers and that STA is not considered a peer again
unless it re-peers. Previously, this inactivity time was
always 30 minutes. Now, add it to the mesh configuration
and allow it to be configured. Retain 30 minutes as a
default value.
Signed-off-by: Colleen Twitty <colleen@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge 'net' bug fixes into 'net-next' as we have patches
that will build on top of them.
This merge commit includes a change from Emil Goode
(emilgoode@gmail.com) that fixes a warning that would
have been introduced by this merge. Specifically it
fixes the pingv6_ops method ipv6_chk_addr() to add a
"const" to the "struct net_device *dev" argument and
likewise update the dummy_ipv6_chk_addr() declaration.
Signed-off-by: David S. Miller <davem@davemloft.net>
The change to use atomic_inc_return() for assigning the wiphy
index made the first wiphy index 1 instead of 0. This is fine,
but we all habitually type "phy0" when we're testing, so make
it go back to 0 instead of 1 by subtracting 1 from the index.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
My big locking cleanups caused a problem by registering the
rfkill instance with the RTNL held, while the callback also
acquires the RTNL. This potentially causes a deadlock since
the two locks used (rfkill mutex and RTNL) can be acquired
in two different orders. Fix this by (un)registering rfkill
without holding the RTNL. This needs to be done after the
device struct is registered, but that can also be done w/o
holding the RTNL.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
get_reg_request_treatment() returns 0 in one case but is
defined to return an enum, use the proper value REG_REQ_OK.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current internal SME implementation in cfg80211 is
very mixed up with the MLME handling, which has been
causing issues for a long time. There are three things
that the implementation has to provide:
* a basic SME implementation for nl80211's connect()
call (for drivers implementing auth/assoc, which is
really just mac80211) and wireless extensions
* MLME events for the userspace SME
* SME events (connected, disconnected etc.) for all
different SME implementation possibilities (driver,
cfg80211 and userspace)
To achieve these goals it isn't necessary to track the
software SME's connection status outside of it's state
(which is the part that caused many issues.) Instead,
track it only in the SME data (wdev->conn) and in the
general case only track whether the wdev is connected
or not (via wdev->current_bss.)
Also separate the internal implementation to not have
callbacks from the SME events, but rather call it from
the API functions that the driver (or rather mac80211)
calls. This separates the code better.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Do some cleanups in the cfg80211 SME APIs, which are
only used by mac80211.
Most of these functions get a frame passed, and there
isn't really any reason to export multiple functions
as cfg80211 can check the frame type instead, do that.
Additionally, the API functions have confusing names
like cfg80211_send_...() which was meant to indicate
that it sends an event to userspace, but gets a bit
confusing when there's both TX and RX and they're not
all clearly labeled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
genlmsg_end() can't return an error since it returns the
skb length so remove checks treating the return value as
an error code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to take up the space for devices that don't
support WoWLAN, and most drivers can even make the support
data static const (except where it's modified at runtime.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
An active monitor interface is one that is used for communication (via
injection). It is expected to ACK incoming unicast packets. This is
useful for running various 802.11 testing utilities that associate to an
AP via injection and manage the state in user space.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
So far, only net_device * could be passed along with netdevice notifier
event. This patch provides a possibility to pass custom structure
able to provide info that event listener needs to know.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
v2->v3: fix typo on simeth
shortened dev_getter
shortened notifier_info struct name
v1->v2: fix notifier_call parameter in call_netdevice_notifier()
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the current WoWLAN configuration available to drivers
at runtime. This isn't really useful for the normal WoWLAN
behaviour and accessing it can also be racy, but drivers
may use it for testing the WoWLAN device behaviour while
the host stays up & running to observe the device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
By making all the API functions require wdev locking we
can clean up the API a bit, getting rid of the locking
version of each function. This also decreases the size
of cfg80211 by a small amount.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
By making all the API functions require wdev locking we
can clean up the API a bit, getting rid of the locking
version of each function. This also decreases the size
of cfg80211 by a small amount.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The reg_mutex is similar to the ones I just removed in
cfg80211 but even less useful since it protects global
data, and we hold the RTNL in all places (except module
unload) already.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since it just does a quick check of the last regulatory
request, the function doesn't have to hold the reg mutex
but can use RCU instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the driver for some reason successfully finishes
scanning while in p2p_stop_device(), cfg80211 will
still set it to aborted. Simplify this code using the
new 'notified' value and only mark it aborted in case
the driver didn't notify cfg80211 at all (in which
case we also leak the request to not crash, this is
a driver bug.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using separate locks in cfg80211 and mac80211 has always
caused issues, for example having to unlock in places in
mac80211 to call cfg80211, which even needed a framework
to make cfg80211 calls after some functions returned etc.
Additionally, I suspect some issues people have reported
with the cfg80211 state getting confused could be due to
such issues, when cfg80211 is asking mac80211 to change
state but mac80211 is in the process of telling cfg80211
that the state changed (in another way.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Virtually all code paths in cfg80211 already (need to) hold
the RTNL. As such, there's little point in having another
four mutexes for various parts of the code, they just cause
lock ordering issues (and much of the time, the RTNL and a
few of the others need thus be held.)
Simplify all this by getting rid of the extra four mutexes
and just use the RTNL throughout. Only a few code changes
were needed to do this and we can get rid of a work struct
for bonus points.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
VHT uses peer AID in the PARTIAL_AID field in TDLS frames. The current
design for TDLS is to first add a dummy STA entry before completing TDLS
Setup and then update information on this STA entry based on what was
received from the peer during the setup exchange.
In theory, this could use NL80211_ATTR_STA_AID to set the peer AID just
like this is used in AP mode to set the AID of an association station.
However, existing cfg80211 validation rules prevent this attribute from
being used with set_station operation. To avoid interoperability issues
between different kernel and user space version combinations, introduce
a new nl80211 attribute for the purpose of setting TDLS peer AID. This
attribute can be used in both the new_station and set_station
operations. It is not supposed to be allowed to change the AID value
during the lifetime of the STA entry, but that validation is left for
drivers to do in the change_station callback.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Copy & paste mistake - STATION_INFO_TX_BYTES64 is the name of the flag,
not NL80211_STA_INFO_TX_BYTES64.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a P2P-Device is present and another virtual interface triggers
the connection work, the system crash because it tries to check
if the P2P-Device's netdev (which doesn't exist) is up. Skip any
wdevs that have no netdev to fix this.
Cc: stable@vger.kernel.org
Reported-by: YanBo <dreamfly281@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Authentication takes place in userspace, but the beacon is
generated in the kernel. Allow userspace to inform the
kernel of the authentication method so the appropriate
mesh config IE can be set prior to beacon generation when
joining the MBSS.
Signed-off-by: Colleen Twitty <colleen@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To support auto-loading of wireless modules from netlink users, add module
alias for nl80211 family.
This also adds NL80211_GENL_NAME constant to define the "nl80211" netlink
family name as part of uapi.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add regulatory class for 60GHz band, according
to the last specification.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code sending the current WoWLAN TCP wakeup settings in
nl80211_send_wowlan_tcp() is not closing the nested attribute,
thus causing the parser to get confused on the receiver side
in userspace (iw). Fix this.
Cc: stable@vger.kernel.org [3.9]
Reported-by: Deepak Arora <deepakx.arora@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the interface goes down, there's no need to call
cfg80211_mlme_down() after __cfg80211_disconnect() as
the latter will call the former (if appropriate.)
Also, in __cfg80211_disconnect(), if the cfg80211 SME
isn't used, __cfg80211_disconnected() may still need
to be called (depending on the current state) so that
the SME state gets cleared.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Adding the attributes fixes an issue with P2P Device not
working properly for management frame TX.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the device reports a non-wireless wakeup reason, the
tracing code crashes trying to dereference a NULL pointer.
Fix this by checking the pointer on all accesses and also
add a non_wireless tag to the event.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If rfkill_register() fails in wiphy_register() the struct device
is unregistered but everything else isn't (regulatory, debugfs)
and we even leave the wiphy instance on all internal lists even
though it will likely be freed soon, which is clearly a problem.
Fix this by cleaning up properly.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull VFS updates from Al Viro,
Misc cleanups all over the place, mainly wrt /proc interfaces (switch
create_proc_entry to proc_create(), get rid of the deprecated
create_proc_read_entry() in favor of using proc_create_data() and
seq_file etc).
7kloc removed.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (204 commits)
don't bother with deferred freeing of fdtables
proc: Move non-public stuff from linux/proc_fs.h to fs/proc/internal.h
proc: Make the PROC_I() and PDE() macros internal to procfs
proc: Supply a function to remove a proc entry by PDE
take cgroup_open() and cpuset_open() to fs/proc/base.c
ppc: Clean up scanlog
ppc: Clean up rtas_flash driver somewhat
hostap: proc: Use remove_proc_subtree()
drm: proc: Use remove_proc_subtree()
drm: proc: Use minor->index to label things, not PDE->name
drm: Constify drm_proc_list[]
zoran: Don't print proc_dir_entry data in debug
reiserfs: Don't access the proc_dir_entry in r_open(), r_start() r_show()
proc: Supply an accessor for getting the data from a PDE's parent
airo: Use remove_proc_subtree()
rtl8192u: Don't need to save device proc dir PDE
rtl8187se: Use a dir under /proc/net/r8180/
proc: Add proc_mkdir_data()
proc: Move some bits from linux/proc_fs.h to linux/{of.h,signal.h,tty.h}
proc: Move PDE_NET() to fs/proc/proc_net.c
...
Don't use create_proc_read_entry() as that is deprecated, but rather use
proc_create_data() and seq_file instead.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: Jouni Malinen <j@w1.fi>
cc: John W. Linville <linville@tuxdriver.com>
cc: Johannes Berg <johannes@sipsolutions.net>
cc: linux-wireless@vger.kernel.org
cc: netdev@vger.kernel.org
cc: devel@driverdev.osuosl.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Some protocols need a more reliable connection to complete
successful in reasonable time. This patch adds a user-space
API to indicate the wireless driver that a critical protocol
is about to commence and when it is done, using nl80211 primitives
NL80211_CMD_CRIT_PROTOCOL_START and NL80211_CRIT_PROTOCOL_STOP.
There can be only on critical protocol session started per
registered cfg80211 device.
The driver can support this by implementing the cfg80211 callbacks
.crit_proto_start() and .crit_proto_stop(). Examples of protocols
that can benefit from this are DHCP, EAPOL, APIPA. Exactly how the
link can/should be made more reliable is up to the driver. Things
to consider are avoid scanning, no multi-channel operations, and
alter coexistence schemes.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In cfg80211_can_use_iftype_chan(), check for P2P Device
first, and then for netdevs. This doesn't really change
anything but makes the code a bit easier to read since
it may not be obvious for everyone at first that a P2P
device has no netdev.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211_stop_p2p_device() requires the devlist_mtx to
be held, but nl80211_stop_p2p_device() doesn't acquire
it which is a locking error and causes a warning (when
lockdep is enabled). Fix this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Most dump callbacks, including the scan results one, use
the netdev to identify what to do, which is incorrect for
the P2P_DEVICE support, it needs to be able to get the
scan result from the wdev. Change all dumps to unify the
code, but ones other than scan don't really support being
executed on a wdev that has no netdev.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This function converts a (global only!) operating
class to an internal band identifier. This will
be needed for extended channel switch support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a full scan 2.4 and 5 GHz scan is scheduled, but then the 2.4 GHz
part of the scan disables a 5.2 GHz channel due to, e.g. receiving
country or frequency information, that 5.2 GHz channel might already
be in the list of channels to scan next. Then, when the driver checks
if it should do a passive scan, that will return false and attempt an
active scan. This is not only wrong but can also lead to the iwlwifi
device firmware crashing since it checks regulatory as well.
Fix this by not setting the channel flags to just disabled but rather
OR'ing in the disabled flag. That way, even if the race happens, the
channel will be scanned passively which is still (mostly) correct.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
net/mac80211/sta_info.c
net/wireless/core.h
Two minor conflicts in wireless. Overlapping additions of extern
declarations in net/wireless/core.h and a bug fix overlapping with
the addition of a boolean parameter to __ieee80211_key_free().
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduced in f9f475292d
("cfg80211: always check for scan end on P2P device")
cfg80211_conn_scan() which requires sched_scan_mtx to be held can be called
from cfg80211_conn_work(). Without this we are hitting multiple warnings like
the following:
WARNING: at net/wireless/sme.c:88 cfg80211_conn_scan+0x1dc/0x3a0 [cfg80211]()
Hardware name: 0578A21
Modules linked in: ...
Pid: 620, comm: kworker/3:1 Not tainted 3.9.0-rc4-next-20130328+ #326
Call Trace:
[<c1036992>] warn_slowpath_common+0x72/0xa0
[<c10369e2>] warn_slowpath_null+0x22/0x30
[<faa4b0ec>] cfg80211_conn_scan+0x1dc/0x3a0 [cfg80211]
[<faa4b344>] cfg80211_conn_do_work+0x94/0x380 [cfg80211]
[<faa4c3b2>] cfg80211_conn_work+0xa2/0x130 [cfg80211]
[<c1051858>] process_one_work+0x198/0x450
Signed-off-by: Artem Savkov <artem.savkov@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a new constant ETH_P_802_3_MIN, the minimum ethernet type for
an 802.3 frame. Frames with a lower value in the ethernet type field
are Ethernet II.
Also update all the users of this value that David Miller and
I could find to use the new constant.
Also correct a bug in util.c. The comparison with ETH_P_802_3_MIN
should be >= not >.
As suggested by Jesse Gross.
Compile tested only.
Cc: David Miller <davem@davemloft.net>
Cc: Jesse Gross <jesse@nicira.com>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Bart De Schuymer <bart.de.schuymer@pandora.be>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: linux-bluetooth@vger.kernel.org
Cc: netfilter-devel@vger.kernel.org
Cc: bridge@lists.linux-foundation.org
Cc: linux-wireless@vger.kernel.org
Cc: linux1394-devel@lists.sourceforge.net
Cc: linux-media@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: dev@openvswitch.org
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a P2P device wdev is removed while it has a scan, then the
scan completion might crash later as it is already freed by
that time. To avoid the crash always check the scan completion
when the P2P device is being removed for some reason. If the
driver already canceled it, don't want and free it, otherwise
warn and leak it to avoid later crashes.
In order to do this, locking needs to be changed away from the
rdev mutex (which can't always be guaranteed). For now, use
the sched_scan_mtx instead, I'll rename it to just scan_mtx in
a later patch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Arend reported a crash in tracing if the driver returns an
ERR_PTR() value from the add_virtual_intf() callback. This
is due to the tracing then still attempting to dereference
the "pointer", fix this by using IS_ERR_OR_NULL().
Reported-by: Arend van Spriel <arend@broadcom.com>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If wpa_supplicant and iw/iwconfig are used together, very
rarely the system crashes. It seems to be related to the
connection parameters not being set up, but it's not all
clear to me how this happens. In any case, checking that
the conn pointer exists here is probably a good idea.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the odd case that while updating information from a beacon,
a BSS was found that is part of a hidden group, we drop the
new information. In this case, however, we leak the IE buffer
from the update, and erroneously update the entry's timestamp
so it will never time out. Fix both these issues.
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is NETDEV_ENTRY that was incorrectly assigned as WIPHY_ASSIGN,
fix it.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the user requested a userspace MPM, automatically
disable auto_open_plinks to fully disable the kernel MPM.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The mesh station types used to refer to whether the
station was secure or nonsecure. Really the salient
information is whether it is managed by the kernel or
userspace
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Secure mesh had the implicit requirement that the Mesh
Peering Management entity be in userspace. However
userspace might want to implement an open MPM as well, so
specify a mesh setup parameter to indicate this.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For VHT, the wider bandwidths (up to 160 MHz) need
to be allowed. Since world roaming only covers the
case of connecting to an AP, it can be opened up
there, we will rely on the AP to know the local
regulations.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no reason TDLS should be prevented on P2P client
interfaces, and most of the code already handles it, so
allow adding stations for it.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If possible that after suspend, cfg80211 will receive request to
disconnect what require action on interface that was removed during
suspend.
Problem can manifest itself by various warnings similar to below one:
WARNING: at net/mac80211/driver-ops.h:12 ieee80211_bss_info_change_notify+0x2f9/0x300 [mac80211]()
wlan0: Failed check-sdata-in-driver check, flags: 0x4
Call Trace:
[<c043e0b3>] warn_slowpath_fmt+0x33/0x40
[<f83707c9>] ieee80211_bss_info_change_notify+0x2f9/0x300 [mac80211]
[<f83a660a>] ieee80211_recalc_ps_vif+0x2a/0x30 [mac80211]
[<f83a6706>] ieee80211_set_disassoc+0xf6/0x500 [mac80211]
[<f83a9441>] ieee80211_mgd_deauth+0x1f1/0x280 [mac80211]
[<f8381b36>] ieee80211_deauth+0x16/0x20 [mac80211]
[<f8261e70>] cfg80211_mlme_down+0x70/0xc0 [cfg80211]
[<f8264de1>] __cfg80211_disconnect+0x1b1/0x1d0 [cfg80211]
To fix the problem disconnect from any associated network before
suspend. User space is responsible to establish connection again
after resume. This basically need to be done by user space anyway,
because associated stations can go away during suspend (for example
NetworkManager disconnects on suspend and connect on resume by default).
Patch also handle situation when driver refuse to suspend with wowlan
configured and try to suspend again without it.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add NL80211_CMD_UPDATE_FT_IES to support update of FT IEs to the WLAN
driver and NL80211_CMD_FT_EVENT to send FT events from the WLAN driver.
This will carry the target AP's MAC address along with the relevant
Information Elements. This event is used to report received FT IEs
(MDIE, FTIE, RSN IE, TIE, RICIE). These changes allow FT to be supported
with drivers that use an internal SME instead of user space option (like
FT implementation in wpa_supplicant with mac80211-based drivers).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
