This is done as a preparation before removing support for vlan dump from
DSA core. The vlans are synced with the bridge and thus there is no
need for special dump operation support.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The prepare phase for FDB add is unneeded because most of DSA devices
can have failures during bus transactions (SPI, I2C, etc.), thus, the
prepare phase cannot guarantee success of the commit stage.
The support for learning FDB through notification chain, which will be
introduced in the following patches, will provide the ability to notify
back the bridge about successful offload.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support FDB add/del to be on a notifier chain the slave
API need to be changed to be switchdev independent.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make hdlcdrv_ops structures const as they are only passed to
hdlcdrv_register function. The corresponding argument is of type const,
so make the structures const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in dev_err error message and also
split overly long line to avoid a checkpatch warning.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In lan9303_get_ethtool_stats: Get rid of 0x400 constant magic
by using new lan9303_read_switch_reg() inside loop.
Reduced scope of two variables.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lan9303_enable_packet_processing, lan9303_disable_packet_processing
functions operate on port, so the names should reflect that.
And to align with lan9303_disable_processing(), rename:
lan9303_enable_packet_processing -> lan9303_enable_processing_port
lan9303_disable_packet_processing -> lan9303_disable_processing_port
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify usage of lan9303_enable_packet_processing,
lan9303_disable_packet_processing()
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Will be used instead of '3' in upcomming patches.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
lan9303_enable_packet_processing, lan9303_disable_packet_processing()
Pass port number (0,1,2) as parameter instead of port offset.
Because other functions in the module pass port numbers.
And to enable simplifications in following patch.
Introduce lan9303_write_switch_port().
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reporting any return code for a receive buffer as an "rx error" only
produces alarming noise and the only values that have been observed to be
used in this field are not error conditions. Change this to a netdev_dbg
with a more descriptive message.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first wireless-drivers-next pull request for 4.14. I'm submitting
this unusally late in the cycle as my vacation postponed this. But
even if this is late there's not still that much new features, mostly
cleanup or fixes.
Major changes:
ath10k
* preparation for wcn3990 support
iwlwifi
* Reorganization of the code into separate directories continues
qtnfmac
* regulatory support updates
* add get_channel, dump_survey and channel_switch cfg80211 handlers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZiHuQAAoJEG4XJFUm622bVSEIAKdausycC6OOZjwTGWnFyxE/
58n79VTrTbXVLwJ7lSBCGYCTujc7amPxAVlDOLYd+9TKm0fO7gap50Gdl35HO5sp
9v/augHQSouz52q2vgsTi0JbXsqhJQZ4Ie4P0fo8OyqJMYAvFga2FhFBpJseMYd9
NX88SMoxAGgDkTC0JfzzLnA/jZ0W6ULai6zmRE1s6lUIynP2kzHgpfbMH3+KEkod
SUW+yX91MdOkkyFGXyY11uuBqanUpEVSAQXW6J76vw3qS88qIqaL3iIeJ6C4Vozq
fKNkHN4iZOd9FlKY1IFi4vS0+7hWiq6DQ3c+ngtU6cuq1XdBa6PuanC3I2e0B8E=
=PKUU
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-08-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.14
The first wireless-drivers-next pull request for 4.14. I'm submitting
this unusally late in the cycle as my vacation postponed this. But
even if this is late there's not still that much new features, mostly
cleanup or fixes.
Major changes:
ath10k
* preparation for wcn3990 support
iwlwifi
* Reorganization of the code into separate directories continues
qtnfmac
* regulatory support updates
* add get_channel, dump_survey and channel_switch cfg80211 handlers
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Without CONFIG_PCI_IOV, we get a harmless warning about an
unused function:
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c:2273:13: error: 'hclge_disable_sriov' defined but not used [-Werror=unused-function]
The #ifdefs in this driver are obviously wrong, so this just
removes them and uses an IS_ENABLED() check that does the same
thing correctly in a more readable way.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series includes some mlx5 updates for both net-next and rdma trees.
From Saeed,
Core driver updates to allow selectively building the driver with
or without some large driver components, such as
- E-Switch (Ethernet SRIOV support).
- Multi-Physical Function Switch (MPFs) support.
For that we split E-Switch and MPFs functionalities into separate files.
From Erez,
Delay mlx5_core events when mlx5 interfaces, namely mlx5_ib, registration
is taking place and until it completes.
From Rabie,
Increase the maximum supported flow counters.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZiDoAAAoJEEg/ir3gV/o+594H/RH5kRwC719s/5YQFJXvGsVC
fjtj3UUJPLrWB8XBh7a4PRcxXPIHaFKJuY3MU7KHFIeZQFklJcit3njjpxDlUINo
F5S1LHBSYBkeMD/ksWBA8OLCBprNGN6WQ2tuFfAjZlQQ44zqv8LJmegoDtW9bGRy
aGAkjUmALEblQsq81y0BQwN2/8DA8HAywrs8L2dkH1LHwijoIeYMZFOtKugv1FbB
ABSKxcU7D/NYw6rsVdZG59fHFQ+eKOspDFqBZrUzfQ+zUU2hFFo96ovfXBfIqYCV
7BtJuKXu2LeGPzFLsuw4h1131iqFT1iSMy9fEhf/4OwaL/KPP/+Umy8vP/XfM+U=
=wCpd
-----END PGP SIGNATURE-----
Merge tag 'mlx5-shared-2017-08-07' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Saeed Mahameed says:
====================
mlx5-shared-2017-08-07
This series includes some mlx5 updates for both net-next and rdma trees.
From Saeed,
Core driver updates to allow selectively building the driver with
or without some large driver components, such as
- E-Switch (Ethernet SRIOV support).
- Multi-Physical Function Switch (MPFs) support.
For that we split E-Switch and MPFs functionalities into separate files.
From Erez,
Delay mlx5_core events when mlx5 interfaces, namely mlx5_ib, registration
is taking place and until it completes.
From Rabie,
Increase the maximum supported flow counters.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When Ethernet frames span mulitple URBs, the netdev buffer memory
pointed to by the asix_rx_fixup_info structure remains allocated
during the time gap between the 2 executions of asix_rx_fixup_internal().
This means that if ax88772_unbind() is called within this time
gap to free the memory of the parent private data structure then
a memory leak of the part filled netdev buffer memory will occur.
Therefore, create a new function asix_rx_fixup_common_free() to
free the memory of the netdev buffer and add a call to
asix_rx_fixup_common_free() from inside ax88772_unbind().
Consequently when an unbind occurs part way through receiving
an Ethernet frame, the netdev buffer memory that is holding part
of the received Ethernet frame will now be freed.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a risk that the members of the structure asix_rx_fixup_info
become unsynchronised leading to the possibility of a malfunction.
For example, rx->split_head was not being set to false after an
error was detected so potentially could cause a malformed 32-bit
Data header word to be formed.
Therefore add function reset_asix_rx_fixup_info() to reset all the
members of asix_rx_fixup_info so that future processing will start
with known initial conditions.
Also, if (skb->len != offset) becomes true then call
reset_asix_rx_fixup_info() so that the processing of the next URB
starts with known initial conditions. Without the call, the check
does nothing which potentially could lead to a malfunction
when the next URB is processed.
In addition, for robustness, call reset_asix_rx_fixup_info() before
every error path's "return 0". This ensures that the next URB is
processed from known initial conditions.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In asix_rx_fixup_internal() there is a risk that rx->ax_skb gets
reused after passing the Ethernet frame into the network stack via
usbnet_skb_return().
The risks include:
a) asynchronously freeing rx->ax_skb after passing the netdev buffer
to the NAPI layer which might corrupt the backlog queue.
b) erroneously reusing rx->ax_skb such as calling skb_put_data() multiple
times which causes writing off the end of the netdev buffer.
Therefore add a defensive rx->ax_skb = NULL after usbnet_skb_return()
so that it is not possible to free rx->ax_skb or to apply
skb_put_data() too many times.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of struct tc_to_netdev which is now just unnecessary container
and rather pass per-type structures down to drivers directly.
Along with that, consolidate the naming of per-type structure variables
in cls_*.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the return value from -EINVAL to -EOPNOTSUPP. The rest of the
drivers have it like that, so be aligned.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
prio is not cls_flower specific, but it is meaningful for all
classifiers. Seems that only mlxsw cares about the value. Obviously,
cls offload in other drivers is broken.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As ndo_setup_tc is generic offload op for whole tc subsystem, does not
really make sense to have cls-specific args. So move them under
cls_common structurure which is embedded in all cls structs.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to the rest offloaders of mqprio, no need to check handle.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the flows a bit in preparation of follow-up changes in
ndo_setup_tc args. Also, change the error code to align with the rest of
the drivers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To sync-up with the naming in the rest of the driver, rename the cls arg.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let mlxsw_sp_setup_tc be a splitter for specific setup_tc types and push
out cls_flower and cls_matchall specific codes into separate functions.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let mlx5e_rep_setup_tc (former mlx5e_rep_ndo_setup_tc) be a splitter for
specific setup_tc types and push out cls_flower specific code into
a separate function.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let mlx5e_setup_tc (former mlx5e_ndo_setup_tc) be a splitter for specific
setup_tc types and push out cls_flower and mqprio specific codes into
separate functions. Also change the return values so they are the same
as in the rest of the drivers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let __ixgbe_setup_tc be a splitter for specific setup_tc types and push out
cls_u32 and mqprio specific codes into separate functions. Also change
the return values so they are the same as in the rest of the drivers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let cxgb_setup_tc be a splitter for specific setup_tc types and push out
cls_u32 specific code into a separate function.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since this is specific to flower now, make it part of the flower offload
struct.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to be aligned with the rest of the types, rename
TC_SETUP_MATCHALL to TC_SETUP_CLSMATCHALL.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the type is always present, push it to be a separate argument to
ndo_setup_tc. On the way, name the type enum and use it for arg type.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Read new NIC capability field which represnts 16 MSBs of the max flow
counters number supported (max_flow_counter_31_16).
Backward compatibility with older firmware is preserved, the modified
driver reads max_flow_counter_31_16 as 0 from the older firmware and
uses up to 64K counters.
Changed flow counter id from 16 bits to 32 bits. Backward compatibility
with older firmware is preserved as we kept the 16 LSBs of the counter
id in place and added 16 MSBs from reserved field.
Changed the background bulk reading of flow counters to work in chunks
of at most 32K counters, to make sure we don't attempt to allocate very
large buffers.
Signed-off-by: Rabie Loulou <rabiel@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When mlx5_ib registers itself to mlx5_core as an interface, it will
call mlx5_add_device which will call mlx5_ib interface add callback,
in case the latter successfully returns, only then mlx5_core will add
it to the interface list and async events will be forwarded to mlx5_ib.
Between mlx5_ib interface add callback and mlx5_core adding the mlx5_ib
interface to its devices list, arriving mlx5_core events can be missed
by the new mlx5_ib registering interface.
In other words:
thread 1: mlx5_ib: mlx5_register_interface(dev)
thread 1: mlx5_core: mlx5_add_device(dev)
thread 1: mlx5_core: ctx = dev->add => (mlx5_ib)->mlx5_ib_add
thread 2: mlx5_core_event: **new event arrives, forward to dev_list
thread 1: mlx5_core: add_ctx_to_dev_list(ctx)
/* previous event was missed by the new interface.*/
It is ok to miss events before dev->add (mlx5_ib)->mlx5_ib_add_device
but not after.
We fix this race by accumulating the events that come between the
ib_register_device (inside mlx5_add_device->(dev->add)) till the adding
to the list completes and fire them to the new registering interface
after that.
Fixes: f1ee87fe55 ("net/mlx5: Organize device list API in one place")
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Allow to selectively build the driver with or without sriov eswitch, VF
representors and TC offloads.
Also remove the need of two ndo ops structures (sriov & basic)
and keep only one unified ndo ops, compile out VF SRIOV ndos when not
needed (MLX5_ESWITCH=n), and for VF netdev calling those ndos will result
in returning -EPERM.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Jes Sorensen <jsorensen@fb.com>
Cc: kernel-team@fb.com
Multi-Physical Function Switch (MPFs) is required for when multi-PF
configuration is enabled to allow passing user configured unicast MAC
addresses to the requesting PF.
Before this patch eswitch.c used to manage the HW MPFS l2 table,
E-Switch always (regardless of sriov) enabled vport(0) (NIC PF) vport's
contexts update on unicast mac address list changes, to populate the PF's
MPFS L2 table accordingly.
In downstream patch we would like to allow compiling the driver without
E-Switch functionalities, for that we move MPFS l2 table logic out
of eswitch.c into its own file, and provide Kconfig flag (MLX5_MPFS) to
allow compiling out MPFS for those who don't want Multi-PF support.
NIC PF netdevice will now directly update MPFS l2 table via the new MPFS
API. VF netdevice has no access to MPFS L2 table, so E-Switch will remain
responsible of updating its MPFS l2 table on behalf of its VFs.
Due to this change we also don't require enabling vport(0) (PF vport)
unicast mac changes events anymore, for when SRIOV is not enabled.
Which means E-Switch is now activated only on SRIOV activation, and not
required otherwise.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jes Sorensen <jsorensen@fb.com>
Cc: kernel-team@fb.com
Expose MLX5_VPORT_MANAGER macro to check for strict vport manager
E-switch and MPFS (Multi Physical Function Switch) abilities.
VPORT manager must be a PF with an ethernet link and with FW advertised
vport group manager capability
Replace older checks with the new macro and use it where needed in
eswitch.c and mlx5e netdev eswitch related flows.
The same macro will be reused in MPFS separation downstream patch.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Remove redundant call to unregister vport representor in mlx5e_add error
flow.
Hide the representor priv and eswitch internal structures from en_main.c
as preparation step for downstream patches which would allow building
the driver without support for representors and eswitch.
Fixes: 6f08a22c5f ("net/mlx5e: Register/unregister vport representors on interface attach/detach")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Since we are going to allow building the driver without eswitch support,
it would be possible to compile out the sriov netdevice ops struct such
that the basic ops instance will be used for non VF devices too.
Add missing udp tunnel ndos into mlx5e_netdev_ops_basic.
While here, rearrange some ndos in the sriov ops struct and put
vf/eswitch related ndos towards the end of it.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Before the GMAC on the Anarion chip can be used, the PHY interface
selection must be configured with the DWMAC block in reset.
This layer covers a block containing only two registers. Although it
is possible to model this as a reset controller and use the "resets"
property of stmmac, it's much more intuitive to include this in the
glue layer instead.
At this time only RGMII is supported, because it is the only mode
which has been validated hardware-wise.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With new transparent VF support, it is possible to get a deadlock
when some of the deferred work is running and the unregister_vf
is trying to cancel the work element. The solution is to use
trylock and reschedule (similar to bonding and team device).
Reported-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Fixes: 0c195567a8 ("netvsc: transparent VF management")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing sub channel code did not wait for all the sub-channels
to completely initialize. This could lead to race causing crash
in napi_netif_del() from bad list. The existing code would send
an init message, then wait only for the initial response that
the init message was received. It thought it was waiting for
sub channels but really the init response did the wakeup.
The new code keeps track of the number of open channels and
waits until that many are open.
Other issues here were:
* host might return less sub-channels than was requested.
* the new init status is not valid until after init was completed.
Fixes: b3e6b82a00 ("hv_netvsc: Wait for sub-channels to be processed during probe")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using Broadcom Systemport device in 32bit Platform, ifconfig can
only report up to 4G tx,rx status, which will be wrapped to 0 when the
number of incoming or outgoing packets exceeds 4G, only taking
around 2 hours in busy network environment (such as streaming).
Therefore, it makes hard for network diagnostic tool to get reliable
statistical result, so the patch is used to add 64bit support for
Broadcom Systemport device in 32bit Platform.
This patch provides 64bit statistics capability on both ethtool and ifconfig.
Signed-off-by: Jianming.qiao <kiki-good@hotmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving PF module param console_bitmask to lio_main.c for consistency.
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's supposed to be a one-to-one correspondence between the 18 macros
that #define the OCT_DEV states (in octeon_device.h) and the strings in the
oct_dev_state_str array, but there are only 14 strings in the array.
Add the missing strings (so they become 18 in total), and also revise some
incorrect/outdated text of existing strings.
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for SFP hotpluggable modules via sfp-bus and phylink.
This supports both copper and optical SFP modules, which require
different Serdes modes in order to properly negotiate the link.
Optical SFP modules typically require the Serdes link to be talking
1000BaseX mode - this is the gigabit ethernet mode defined by the
802.3 standard.
Copper SFP modules typically integrate a PHY in the module to convert
from Serdes to copper, and the PHY will be configured by the vendor
to either present a 1000BaseX Serdes link (for fixed 1000BaseT) or a
SGMII Serdes link. However, this is vendor defined, so we instead
detect the PHY, switch the link to SGMII mode, and use traditional
PHY based negotiation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add in-band autonegotation support for 10GBase-KR mode.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for reading and writing the clause 45 MII registers.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for reading module EEPROMs through phylink.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link between the ethernet MAC and its PHY has become more complex
as the interface evolves. This is especially true with serdes links,
where the part of the PHY is effectively integrated into the MAC.
Serdes links can be connected to a variety of devices, including SFF
modules soldered down onto the board with the MAC, a SFP cage with
a hotpluggable SFP module which may contain a PHY or directly modulate
the serdes signals onto optical media with or without a PHY, or even
a classical PHY connection.
Moreover, the negotiation information on serdes links comes in two
varieties - SGMII mode, where the PHY provides its speed/duplex/flow
control information to the MAC, and 1000base-X mode where both ends
exchange their abilities and each resolve the link capabilities.
This means we need a more flexible means to support these arrangements,
particularly with the hotpluggable nature of SFP, where the PHY can
be attached or detached after the network device has been brought up.
Ethtool information can come from multiple sources:
- we may have a PHY operating in either SGMII or 1000base-X mode, in
which case we take ethtool/mii data directly from the PHY.
- we may have a optical SFP module without a PHY, with the MAC
operating in 1000base-X mode - the ethtool/mii data needs to come
from the MAC.
- we may have a copper SFP module with a PHY whic can't be accessed,
which means we need to take ethtool/mii data from the MAC.
Phylink aims to solve this by providing an intermediary between the
MAC and PHY, providing a safe way for PHYs to be hotplugged, and
allowing a SFP driver to reconfigure the serdes connection.
Phylink also takes over support of fixed link connections, where the
speed/duplex/flow control are fixed, but link status may be controlled
by a GPIO signal. By avoiding the fixed-phy implementation, phylink
can provide a faster response to link events: fixed-phy has to wait for
phylib to operate its state machine, which can take several seconds.
In comparison, phylink takes milliseconds.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- remove sync status
- rework supported and advertisment handling
- add 1000base-x speed for fixed links
- use functionality exported from phy-core, reworking
__phylink_ethtool_ksettings_set for it
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an I2C MDIO bus bridge library, to allow phylib to access PHYs which
are connected to an I2C bus instead of the more conventional MDIO bus.
Such PHYs can be found in SFP adapters and SFF modules.
Since PHYs appear at I2C bus address 0x40..0x5f, and 0x50/0x51 are
reserved for SFP EEPROMs/diagnostics, we must not allow the MDIO bus
to access these I2C addresses.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylink will need phy_start_machine exported, so lets export it as a
GPL symbol. Documentation/networking/phy.txt indicates that this
should be a PHY API function.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes, we need to do additional work between the PHY coming up and
marking the carrier present - for example, we may need to wait for the
PHY to MAC link to finish negotiation. This changes phylib to provide
a notification function pointer which avoids the built-in
netif_carrier_on() and netif_carrier_off() functions.
Standard ->adjust_link functionality is provided by hooking a helper
into the new ->phy_link_change method.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing 1000Base-X entry to the phy settings table. This was
not included because the original code could not cope with more than
32 bits of link mode mask.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_lookup_setting() provides useful functionality in ethtool code
outside phylib. Move it to phy-core and allow it to be re-used (eg,
in phylink) rather than duplicated elsewhere. Note that this supports
the larger linkmode space.
As we move the phy settings table, we also need to move the guts of
phy_supported_speeds() as well.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Other code would like to make use of this, so make the speed and duplex
string generation visible, and place it in a separate file.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the phy settings table to support more than 32 link modes by
switching to the ethtool link mode bit number representation, rather
than storing the mask. This will allow phylink and other ethtool
code to share the settings table to look up settings.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for GRO (generic receive offload) for aQuantia Atlantic driver.
This results in a perfomance improvement when GRO is enabled.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even the driver doesn't do anything with the clk source for SGMII
ports it needs to be enabled by doing a devm_clk_get(), if there is
a clk source in DT.
Fixes: 0db01097ca ('xgene: Don't fail probe, if there is no clk resource for SGMII interfaces')
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Tested-by: Laura Abbott <labbott@redhat.com>
Acked-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rest of the helpers are named tcf_exts_*, so change the name of
the action number helpers to be aligned. While at it, change to inline
functions.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each multicast group (MID) stores a bitmap of ports to which a packet
should be forwarded to in case an MDB entry associated with the MID is
hit.
Since the initial introduction of IGMP snooping in commit 3a49b4fde2
("mlxsw: Adding layer 2 multicast support") the driver didn't correctly
free these multicast groups upon ungraceful situations such as the
removal of the upper bridge device or module removal.
The correct way to fix this is to associate each MID with the bridge
ports member in it and then drop the reference in case the bridge port
is destroyed, but this will result in a lot more code and will be fixed
in net-next.
For now, upon module removal, traverse the MID list and release each
one.
Fixes: 3a49b4fde2 ("mlxsw: Adding layer 2 multicast support")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some operations in the bridge driver such as MDB deletion are preformed
in an atomic context and thus deferred to a process context by the
switchdev infrastructure.
Therefore, by the time the operation is performed by the underlying
device driver it's possible the bridge port context is already gone.
This is especially true for removal flows, but theoretically can also be
invoked during addition.
Remove the warnings in such situations and return normally.
Fixes: c57529e1d5 ("mlxsw: spectrum: Replace vPorts with Port-VLAN")
Fixes: 3922285d96 ("net: bridge: Add support for offloading port attributes")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the __udivdi3 undefined error reported by
test robot.
Fixes: b8c17f7088 ("net: hns: Add self-adaptive interrupt coalesce support in hns driver")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was supposed to be a bitwise OR but there is a || vs | typo.
Fixes: 864dc729d5 ("net: phy: marvell: Refactor m88e1121 RGMII delay configuration")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare the datapath for refcounted ubuf_info. Clone ubuf_info with
skb_zerocopy_clone() wherever needed due to skb split, merge, resize
or clone.
Split skb_orphan_frags into two variants. The split, merge, .. paths
support reference counted zerocopy buffers, so do not do a deep copy.
Add skb_orphan_frags_rx for paths that may loop packets to receive
sockets. That is not allowed, as it may cause unbounded latency.
Deep copy all zerocopy copy buffers, ref-counted or not, in this path.
The exact locations to modify were chosen by exhaustively searching
through all code that might modify skb_frag references and/or the
the SKBTX_DEV_ZEROCOPY tx_flags bit.
The changes err on the safe side, in two ways.
(1) legacy ubuf_info paths virtio and tap are not modified. They keep
a 1:1 ubuf_info to sk_buff relationship. Calls to skb_orphan_frags
still call skb_copy_ubufs and thus copy frags in this case.
(2) not all copies deep in the stack are addressed yet. skb_shift,
skb_split and skb_try_coalesce can be refined to avoid copying.
These are not in the hot path and this patch is hairy enough as
is, so that is left for future refinement.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We now have all the necessary IPv6 infrastructure in place, so stop
ignoring these notifications.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without resorting to ACLs, the device performs route lookup solely based
on the destination IP address.
In case source-specific routing is needed, an error is returned and the
abort mechanism is activated, thus allowing the kernel to take over
forwarding decisions.
Instead of aborting, we can trap specific destination prefixes where
source-specific routes are present, but this will result in a lot more
code that is unlikely to ever be used.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case we got a replace event, then the replaced route must exist. If
the route isn't capable of multipath, then replace first matching
non-multipath capable route.
If the route is capable of multipath and matching multipath capable
route is found, then replace it. Otherwise, replace first matching
non-multipath capable route.
The new route is inserted before the replaced one. In case the replaced
route is currently offloaded, then it's overwritten in the device's table
by the new route and later deleted, thus not impacting routed traffic.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow directly connected and remote unicast IPv6 routes to be programmed
to the device's tables.
As with IPv4, identical routes - sharing the same destination prefix -
are ordered in a FIB node according to their table ID and then the
metric. While the kernel doesn't share the same trie for the local and
main table, this does happen in the device, so ordering according to
table ID is needed.
Since individual nexthops can be added and deleted in IPv6, each FIB
entry stores a linked list of the rt6_info structs it represents. Upon
the addition or deletion of a nexthop, a new nexthop group is allocated
according to the new configuration and the old one is destroyed.
Identical groups aren't currently consolidated, but will be in a
follow-up patchset.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only allow FIB offload in the presence of default rules or an l3mdev
rule. In a similar fashion to IPv4 FIB rules, sanitize IPv6 rules.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FIB notification block currently only handles IPv4 events, but we
want to start handling IPv6 events soon, so lay the groundwork now.
Do that by preparing the work item and process it according to the
notified address family.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As in previous patch, ignore IPv6 notifications since the driver doesn't
support these.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're about to add IPv6 notifications in the FIB notification chain, but
the driver currently doesn't support these, so ignore them.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FIB notification chain is currently soley used by IPv4 code.
However, we're going to introduce IPv6 FIB offload support, which
requires these notification as well.
As explained in commit c3852ef7f2 ("ipv4: fib: Replay events when
registering FIB notifier"), upon registration to the chain, the callee
receives a full dump of the FIB tables and rules by traversing all the
net namespaces. The integrity of the dump is ensured by a per-namespace
sequence counter that is incremented whenever a change to the tables or
rules occurs.
In order to allow more address families to use the chain, each family is
expected to register its fib_notifier_ops in its pernet init. These
operations allow the common code to read the family's sequence counter
as well as dump its tables and rules in the given net namespace.
Additionally, a 'family' parameter is added to sent notifications, so
that listeners could distinguish between the different families.
Implement the common code that allows listeners to register to the chain
and for address families to register their fib_notifier_ops. Subsequent
patches will implement these operations in IPv6.
In the future, ipmr and ip6mr will be extended to provide these
notifications as well.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds the support for two related features:
- Support for TX interrupts, with one interrupt for each CPU
- Support for different RX queue distribution modes
MVPP2_QDIST_SINGLE_MODE where a single interrupt, shared by all
CPUs, receives the RX events, and MVPP2_QDIST_MULTI_MODE, where the
per-CPU interrupts used for TX events are also used for RX events.
Since additional interrupts are needed, an update to the Device Tree
binding is needed. However, backward compatibility is preserved with
the old Device Tree binding, by gracefully degrading to the original
behavior, with only one RX interrupt, and TX completion being handled
by an hrtimer.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to the introduction of TX interrupts and improved RX
queue distribution, this commit introduces the concept of "queue
vector". A queue vector represents a number of RX and/or TX queues,
and an associated NAPI instance and interrupt.
This commit currently only creates a single queue_vector, so there are
no changes in behavior, but it paves the way for additional
queue_vector in the next commits.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPv2.2 IP has a concept of "software thread", with all registers
of the PPv2.2 mapped 8 times, for concurrent accesses by 8 "software
threads". In addition, interrupts on RX queues are associated to such
"software thread".
For most cases, we map a "software thread" to the more conventional
concept of CPU, but we will soon have one exception: we will have a
model where we have one TX interrupt per CPU (each using one software
thread), and all RX events mapped to another software thread
(associated to another interrupt).
In preparation for this change, it makes sense to change the naming
from MVPP2_MAX_CPUS to MVPP2_MAX_THREADS, and plan for 8 software
threads instead of 4 currently.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the global variables rxq_number and txq_number hold the
number of per-port TXQs and RXQs. Until now, such numbers were
constant regardless of the driver configuration. As we are going to
introduce different modes for TX and RX queues, these numbers will
depend on the configuration (PPv2.1 vs. PPv2.2, exact queue
distribution logic).
Therefore, as a preparation, we move the number of RXQs and TXQs in
the 'struct mvpp2_port' structure, next to the RXQs and TXQs
descriptor arrays.
For now, they remain initialized to the same default values as
rxq_number/txq_number used to be initialized, but this will change in
future commits.
The only non-mechanical change in this patch is that the check to
verify hardware constraints on the number of RXQs and TXQs is moved
from mvpp2_probe() to mvpp2_port_probe(), since it's now in
mvpp2_port_probe() that we initialize the per-port count of RXQ and
TXQ.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RX queue group allocation is anyway re-done later in
mvpp2_port_init(), so resetting it in mvpp2_init() is not very useful,
and will be annoying as we are going to rework the RX queue group
allocation logic.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MVPP21_ISR_RXQ_GROUP_REG register is not indexed by rxq, but by
port, so we fix the parameter name accordingly. There are no
functional changes.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This operation is required for handling ioctl commands like SIOCGMIIREG,
when debugging MDIO registers from userspace.
This commit adds support for this operation.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the MAINTAINERS file with HNS3 Ethernet driver
maintainers names and other details. This also introduces the new
Makefiles required to build the HNS3 Ethernet driver and updates
the existing Kconfig file in the hisilicon folder.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support of the Ethtool interface to
the HNS3 Ethernet driver. Various commands to read the
statistics, configure the offloading, loopback selftest etc.
are supported.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support of MDIO bus interface for HNS3 driver.
Code provides various interfaces to start and stop the PHY layer
and to read and write the MDIO bus or PHY.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
THis patch adds the support of the Scheduling and Shaping
functionalities during the transmit leg. This also adds the
support of Pause at MAC level. (Pause at per-priority level
shall be added later along with the DCB feature).
Hardware as such consists of two types of cofiguration of 6 level
schedulers. Algorithms varies according to the level and type
of scheduler being used. Current patch is used to initialize
the mapping, algorithms(like SP, DWRR etc) and shaper(CIR, PIR etc)
being used.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support of Hisilicon Network Subsystem Accceleration
Engine and common operations to access it. This layer provides access to the
hardware configuration, hardware statistics. This layer is also
responsible for triggering the initialization of the PHY layer through
the below MDIO layer.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support of IMP (Integrated Management Processor)
command interface to the HNS3 driver.
Each PF/VF has support of CQP(Command Queue Pair) ring interface.
Each CQP consis of send queue CSQ and receive queue CRQ.
There are various commands a PF/VF may support, like for Flow Table
manipulation, Device management, Packet buffer allocation, Forwarding,
VLANs config, Tunneling/Overlays etc.
This patch contains code to initialize the command queue, manage the
command queue descriptors and Rx/Tx protocol with the command processor
in the form of various commands/results and acknowledgements.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support of the HNAE3 (Hisilicon Network
Acceleration Engine 3) framework support to the HNS3 driver.
Framework facilitates clients like ENET(HNS3 Ethernet Driver), RoCE
and user-space Ethernet drivers (like ODP etc.) to register with HNAE3
devices and their associated operations.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support of Hisilicon Network Subsystem 3
Ethernet driver to hip08 family of SoCs.
This driver includes basic Rx/Tx functionality. It also includes
the client registration code with the HNAE3(Hisilicon Network
Acceleration Engine 3) framework.
This work provides the initial support to the hip08 SoC and
would incrementally add features or enhancements.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement .get_channels (ethtool -l) functionality
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement .get_ringparam (ethtool -g) functionality
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vnic server reports the statistics buffer in big endian format and must
be converted to cpu endian in order to be displayed correctly on little
endian lpars.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add counters to report number of packets, bytes, and dropped packets for
each transmit queue and number of packets, bytes, and interrupts for each
receive queue. Modify ethtool callbacks to report the new statistics.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's been a while now since ds->dst is not an array anymore, but a
simple pointer to a dsa_switch_tree.
Fortunately, SF2 does not support multi-chip and thus ds->index is
always 0.
This patch substitutes 'ds->dst[ds->index].' with 'ds->dst->'.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add const to bin_attribute structure as it is only passed to the
functions sysfs_{remove/create}_bin_file. The corresponding
arguments are of type const, so declare the structure to be const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When deal with low and high throughput, it is hard to achiece both
high performance and low latency. In order to achiece that, this patch
calculates the rx rate, and adjust the interrupt coalesce parameter
accordingly.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Tested-by: Weiwei Deng <dengweiwei@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In _rtl_init_mac80211(), hardcoded value for hw->max_listen_interval
and hw->max_rate_tries are replaced by macro and removed the comment.
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sometimes, we might using wifi-only firmware with a combo firmware name,
in this case, do not need to filter bluetooth part from header.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
uninitilized variable, such as .add_req_result might be magic stack
value. Initialize the structure to make it clean.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
