Commit Graph

83 Commits

Author SHA1 Message Date
John Wang
427c940558 net/ncsi: Use real net-device for response handler
When aggregating ncsi interfaces and dedicated interfaces to bond
interfaces, the ncsi response handler will use the wrong net device to
find ncsi_dev, so that the ncsi interface will not work properly.
Here, we use the original net device to fix it.

Fixes: 138635cc27 ("net/ncsi: NCSI response packet handler")
Signed-off-by: John Wang <wangzhiqiang.bj@bytedance.com>
Link: https://lore.kernel.org/r/20201223055523.2069-1-wangzhiqiang.bj@bytedance.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-12-23 12:22:23 -08:00
Joel Stanley
1922a46b8c net/ncsi: Fix netlink registration
If a user unbinds and re-binds a NC-SI aware driver the kernel will
attempt to register the netlink interface at runtime. The structure is
marked __ro_after_init so registration fails spectacularly at this point.

 # echo 1e660000.ethernet > /sys/bus/platform/drivers/ftgmac100/unbind
 # echo 1e660000.ethernet > /sys/bus/platform/drivers/ftgmac100/bind
  ftgmac100 1e660000.ethernet: Read MAC address 52:54:00:12:34:56 from chip
  ftgmac100 1e660000.ethernet: Using NCSI interface
  8<--- cut here ---
  Unable to handle kernel paging request at virtual address 80a8f858
  pgd = 8c768dd6
  [80a8f858] *pgd=80a0841e(bad)
  Internal error: Oops: 80d [#1] SMP ARM
  CPU: 0 PID: 116 Comm: sh Not tainted 5.10.0-rc3-next-20201111-00003-gdd25b227ec1e #51
  Hardware name: Generic DT based system
  PC is at genl_register_family+0x1f8/0x6d4
  LR is at 0xff26ffff
  pc : [<8073f930>]    lr : [<ff26ffff>]    psr: 20000153
  sp : 8553bc80  ip : 81406244  fp : 8553bd04
  r10: 8085d12c  r9 : 80a8f73c  r8 : 85739000
  r7 : 00000017  r6 : 80a8f860  r5 : 80c8ab98  r4 : 80a8f858
  r3 : 00000000  r2 : 00000000  r1 : 81406130  r0 : 00000017
  Flags: nzCv  IRQs on  FIQs off  Mode SVC_32  ISA ARM  Segment none
  Control: 00c5387d  Table: 85524008  DAC: 00000051
  Process sh (pid: 116, stack limit = 0x1f1988d6)
 ...
  Backtrace:
  [<8073f738>] (genl_register_family) from [<80860ac0>] (ncsi_init_netlink+0x20/0x48)
   r10:8085d12c r9:80c8fb0c r8:85739000 r7:00000000 r6:81218000 r5:85739000
   r4:8121c000
  [<80860aa0>] (ncsi_init_netlink) from [<8085d740>] (ncsi_register_dev+0x1b0/0x210)
   r5:8121c400 r4:8121c000
  [<8085d590>] (ncsi_register_dev) from [<805a8060>] (ftgmac100_probe+0x6e0/0x778)
   r10:00000004 r9:80950228 r8:8115bc10 r7:8115ab00 r6:9eae2c24 r5:813b6f88
   r4:85739000
  [<805a7980>] (ftgmac100_probe) from [<805355ec>] (platform_drv_probe+0x58/0xa8)
   r9:80c76bb0 r8:00000000 r7:80cd4974 r6:80c76bb0 r5:8115bc10 r4:00000000
  [<80535594>] (platform_drv_probe) from [<80532d58>] (really_probe+0x204/0x514)
   r7:80cd4974 r6:00000000 r5:80cd4868 r4:8115bc10

Jakub pointed out that ncsi_register_dev is obviously broken, because
there is only one family so it would never work if there was more than
one ncsi netdev.

Fix the crash by registering the netlink family once on boot, and drop
the code to unregister it.

Fixes: 955dc68cb9 ("net/ncsi: Add generic netlink family")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Link: https://lore.kernel.org/r/20201112061210.914621-1-joel@jms.id.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-11-12 17:00:13 -08:00
Jakub Kicinski
66a9b9287d genetlink: move to smaller ops wherever possible
Bulk of the genetlink users can use smaller ops, move them.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-10-02 19:11:11 -07:00
Gustavo A. R. Silva
df561f6688 treewide: Use fallthrough pseudo-keyword
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.

[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through

Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
2020-08-23 17:36:59 -05:00
Miaohe Lin
49b0aa1b65 net/ncsi: use eth_zero_addr() to clear mac address
Use eth_zero_addr() to clear mac address insetad of memset().

Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-23 11:49:41 -07:00
Masahiro Yamada
a7f7f6248d treewide: replace '---help---' in Kconfig files with 'help'
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.

This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.

There are a variety of indentation styles found.

  a) 4 spaces + '---help---'
  b) 7 spaces + '---help---'
  c) 8 spaces + '---help---'
  d) 1 space + 1 tab + '---help---'
  e) 1 tab + '---help---'    (correct indentation)
  f) 1 tab + 1 space + '---help---'
  g) 1 tab + 2 spaces + '---help---'

In order to convert all of them to 1 tab + 'help', I ran the
following commend:

  $ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'

Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
2020-06-14 01:57:21 +09:00
Vijay Khemka
5e0fcc16e5 net/ncsi: Support for multi host mellanox card
Multi host Mellanox cards require MAC affinity to be set
before receiving any config commands. All config commands
should also have unicast address for source address in
command header.

Adding GMA and SMAF(Set Mac Affinity) for Mellanox card
and call these in channel probe state machine if it is
defined in device tree.

Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-09 18:36:22 -08:00
Vijay Khemka
7c7b58d46b net/ncsi: Send device address as source address
After receiving device mac address from device, send this as
a source address for further commands instead of broadcast
address.

This will help in multi host NIC cards.

Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-08 13:09:18 -08:00
Vijay Khemka
9e860947d8 net/ncsi: Fix gma flag setting after response
gma_flag was set at the time of GMA command request but it should
only be set after getting successful response. Movinng this flag
setting in GMA response handler.

This flag is used mainly for not repeating GMA command once
received MAC address.

Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-30 20:34:17 -08:00
Vijay Khemka
cf0eba3342 net/ncsi: Disable global multicast filter
Disabling multicast filtering from NCSI if it is supported. As it
should not filter any multicast packets. In current code, multicast
filter is enabled and with an exception of optional field supported
by device are disabled filtering.

Mainly I see if goal is to disable filtering for IPV6 packets then let
it disabled for every other types as well. As we are seeing issues with
LLDP not working with this enabled filtering. And there are other issues
with IPV6.

By Disabling this multicast completely, it is working for both IPV6 as
well as LLDP.

Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
2019-09-19 18:04:40 -07:00
Ben Wei
6f671045b6 net/ncsi: add response handlers for PLDM over NC-SI
This patch adds handlers for PLDM over NC-SI command response.

This enables NC-SI driver recognizes the packet type so the responses
don't get dropped as unknown packet type.

PLDM over NC-SI are not handled in kernel driver for now, but can be
passed back to user space via Netlink for further handling.

Signed-off-by: Ben Wei <benwei@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-31 23:54:03 -07:00
David S. Miller
68aaf44595 Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Minor conflict in r8169, bug fix had two versions in net
and net-next, take the net-next hunks.

Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-27 14:23:31 -07:00
Ben Wei
6d24e14140 net/ncsi: update response packet length for GCPS/GNS/GNPTS commands
Update response packet length for the following commands per NC-SI spec
- Get Controller Packet Statistics
- Get NC-SI Statistics
- Get NC-SI Pass-through Statistics command

Signed-off-by: Ben Wei <benwei@fb.com>
Reviewed-by: Justin Lee <justin.lee1@dell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-22 19:28:04 -07:00
Justin.Lee1@Dell.com
f6edbf2d61 net/ncsi: Fix the payload copying for the request coming from Netlink
The request coming from Netlink should use the OEM generic handler.

The standard command handler expects payload in bytes/words/dwords
but the actual payload is stored in data if the request is coming from Netlink.

Signed-off-by: Justin Lee <justin.lee1@dell.com>
Reviewed-by: Vijay Khemka <vijaykhemka@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-22 19:27:02 -07:00
Terry S. Duncan
96a1b033ac net/ncsi: Ensure 32-bit boundary for data cksum
The NCSI spec indicates that if the data does not end on a 32 bit
boundary, one to three padding bytes equal to 0x00 shall be present to
align the checksum field to a 32-bit boundary.

Signed-off-by: Terry S. Duncan <terry.s.duncan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-20 12:42:40 -07:00
Thomas Gleixner
2874c5fd28 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 152
Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation either version 2 of the license or at
  your option any later version

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-or-later

has been chosen to replace the boilerplate/reference in 3029 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-30 11:26:32 -07:00
Thomas Gleixner
ec8f24b7fa treewide: Add SPDX license identifier - Makefile/Kconfig
Add SPDX license identifiers to all Make/Kconfig files which:

 - Have no license information of any form

These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:

  GPL-2.0-only

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-21 10:50:46 +02:00
Johannes Berg
ef6243acb4 genetlink: optionally validate strictly/dumps
Add options to strictly validate messages and dump messages,
sometimes perhaps validating dump messages non-strictly may
be required, so add an option for that as well.

Since none of this can really be applied to existing commands,
set the options everwhere using the following spatch:

    @@
    identifier ops;
    expression X;
    @@
    struct genl_ops ops[] = {
    ...,
     {
            .cmd = X,
    +       .validate = GENL_DONT_VALIDATE_STRICT | GENL_DONT_VALIDATE_DUMP,
            ...
     },
    ...
    };

For new commands one should just not copy the .validate 'opt-out'
flags and thus get strict validation.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-27 17:07:22 -04:00
Johannes Berg
8cb081746c netlink: make validation more configurable for future strictness
We currently have two levels of strict validation:

 1) liberal (default)
     - undefined (type >= max) & NLA_UNSPEC attributes accepted
     - attribute length >= expected accepted
     - garbage at end of message accepted
 2) strict (opt-in)
     - NLA_UNSPEC attributes accepted
     - attribute length >= expected accepted

Split out parsing strictness into four different options:
 * TRAILING     - check that there's no trailing data after parsing
                  attributes (in message or nested)
 * MAXTYPE      - reject attrs > max known type
 * UNSPEC       - reject attributes with NLA_UNSPEC policy entries
 * STRICT_ATTRS - strictly validate attribute size

The default for future things should be *everything*.
The current *_strict() is a combination of TRAILING and MAXTYPE,
and is renamed to _deprecated_strict().
The current regular parsing has none of this, and is renamed to
*_parse_deprecated().

Additionally it allows us to selectively set one of the new flags
even on old policies. Notably, the UNSPEC flag could be useful in
this case, since it can be arranged (by filling in the policy) to
not be an incompatible userspace ABI change, but would then going
forward prevent forgetting attribute entries. Similar can apply
to the POLICY flag.

We end up with the following renames:
 * nla_parse           -> nla_parse_deprecated
 * nla_parse_strict    -> nla_parse_deprecated_strict
 * nlmsg_parse         -> nlmsg_parse_deprecated
 * nlmsg_parse_strict  -> nlmsg_parse_deprecated_strict
 * nla_parse_nested    -> nla_parse_nested_deprecated
 * nla_validate_nested -> nla_validate_nested_deprecated

Using spatch, of course:
    @@
    expression TB, MAX, HEAD, LEN, POL, EXT;
    @@
    -nla_parse(TB, MAX, HEAD, LEN, POL, EXT)
    +nla_parse_deprecated(TB, MAX, HEAD, LEN, POL, EXT)

    @@
    expression NLH, HDRLEN, TB, MAX, POL, EXT;
    @@
    -nlmsg_parse(NLH, HDRLEN, TB, MAX, POL, EXT)
    +nlmsg_parse_deprecated(NLH, HDRLEN, TB, MAX, POL, EXT)

    @@
    expression NLH, HDRLEN, TB, MAX, POL, EXT;
    @@
    -nlmsg_parse_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
    +nlmsg_parse_deprecated_strict(NLH, HDRLEN, TB, MAX, POL, EXT)

    @@
    expression TB, MAX, NLA, POL, EXT;
    @@
    -nla_parse_nested(TB, MAX, NLA, POL, EXT)
    +nla_parse_nested_deprecated(TB, MAX, NLA, POL, EXT)

    @@
    expression START, MAX, POL, EXT;
    @@
    -nla_validate_nested(START, MAX, POL, EXT)
    +nla_validate_nested_deprecated(START, MAX, POL, EXT)

    @@
    expression NLH, HDRLEN, MAX, POL, EXT;
    @@
    -nlmsg_validate(NLH, HDRLEN, MAX, POL, EXT)
    +nlmsg_validate_deprecated(NLH, HDRLEN, MAX, POL, EXT)

For this patch, don't actually add the strict, non-renamed versions
yet so that it breaks compile if I get it wrong.

Also, while at it, make nla_validate and nla_parse go down to a
common __nla_validate_parse() function to avoid code duplication.

Ultimately, this allows us to have very strict validation for every
new caller of nla_parse()/nlmsg_parse() etc as re-introduced in the
next patch, while existing things will continue to work as is.

In effect then, this adds fully strict validation for any new command.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-27 17:07:21 -04:00
Michal Kubecek
ae0be8de9a netlink: make nla_nest_start() add NLA_F_NESTED flag
Even if the NLA_F_NESTED flag was introduced more than 11 years ago, most
netlink based interfaces (including recently added ones) are still not
setting it in kernel generated messages. Without the flag, message parsers
not aware of attribute semantics (e.g. wireshark dissector or libmnl's
mnl_nlmsg_fprintf()) cannot recognize nested attributes and won't display
the structure of their contents.

Unfortunately we cannot just add the flag everywhere as there may be
userspace applications which check nlattr::nla_type directly rather than
through a helper masking out the flags. Therefore the patch renames
nla_nest_start() to nla_nest_start_noflag() and introduces nla_nest_start()
as a wrapper adding NLA_F_NESTED. The calls which add NLA_F_NESTED manually
are rewritten to use nla_nest_start().

Except for changes in include/net/netlink.h, the patch was generated using
this semantic patch:

@@ expression E1, E2; @@
-nla_nest_start(E1, E2)
+nla_nest_start_noflag(E1, E2)

@@ expression E1, E2; @@
-nla_nest_start_noflag(E1, E2 | NLA_F_NESTED)
+nla_nest_start(E1, E2)

Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-27 17:03:44 -04:00
David S. Miller
8b44836583 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Two easy cases of overlapping changes.

Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-25 23:52:29 -04:00
Tao Ren
1c5c12ee30 net/ncsi: handle overflow when incrementing mac address
Previously BMC's MAC address is calculated by simply adding 1 to the
last byte of network controller's MAC address, and it produces incorrect
result when network controller's MAC address ends with 0xFF.

The problem can be fixed by calling eth_addr_inc() function to increment
MAC address; besides, the MAC address is also validated before assigning
to BMC.

Fixes: cb10c7c0df ("net/ncsi: Add NCSI Broadcom OEM command")
Signed-off-by: Tao Ren <taoren@fb.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-23 21:15:15 -07:00
Johannes Berg
3b0f31f2b8 genetlink: make policy common to family
Since maxattr is common, the policy can't really differ sanely,
so make it common as well.

The only user that did in fact manage to make a non-common policy
is taskstats, which has to be really careful about it (since it's
still using a common maxattr!). This is no longer supported, but
we can fake it using pre_doit.

This reduces the size of e.g. nl80211.o (which has lots of commands):

   text	   data	    bss	    dec	    hex	filename
 398745	  14323	   2240	 415308	  6564c	net/wireless/nl80211.o (before)
 397913	  14331	   2240	 414484	  65314	net/wireless/nl80211.o (after)
--------------------------------
   -832      +8       0    -824

Which is obviously just 8 bytes for each command, and an added 8
bytes for the new policy pointer. I'm not sure why the ops list is
counted as .text though.

Most of the code transformations were done using the following spatch:
    @ops@
    identifier OPS;
    expression POLICY;
    @@
    struct genl_ops OPS[] = {
    ...,
     {
    -	.policy = POLICY,
     },
    ...
    };

    @@
    identifier ops.OPS;
    expression ops.POLICY;
    identifier fam;
    expression M;
    @@
    struct genl_family fam = {
            .ops = OPS,
            .maxattr = M,
    +       .policy = POLICY,
            ...
    };

This also gets rid of devlink_nl_cmd_region_read_dumpit() accessing
the cb->data as ops, which we want to change in a later genl patch.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-22 10:38:23 -04:00
Kangjie Lu
07660ca679 net: ncsi: fix a missing check for nla_nest_start
nla_nest_start may fail and thus deserves a check.

The fix returns -EMSGSIZE in case it fails.

Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-16 11:44:33 -07:00
Vijay Khemka
16e8c4ca21 net/ncsi: Add NCSI Mellanox OEM command
This patch adds OEM Mellanox commands and response handling. It also
defines OEM Get MAC Address handler to get and configure the device.

ncsi_oem_gma_handler_mlx: This handler send NCSI mellanox command for
getting mac address.
ncsi_rsp_handler_oem_mlx: This handles response received for all
mellanox OEM commands.
ncsi_rsp_handler_oem_mlx_gma: This handles get mac address response and
set it to device.

Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-27 16:37:20 -08:00
Samuel Mendoza-Jonas
8d951a75d0 net/ncsi: Configure multi-package, multi-channel modes with failover
This patch extends the ncsi-netlink interface with two new commands and
three new attributes to configure multiple packages and/or channels at
once, and configure specific failover modes.

NCSI_CMD_SET_PACKAGE mask and NCSI_CMD_SET_CHANNEL_MASK set a whitelist
of packages or channels allowed to be configured with the
NCSI_ATTR_PACKAGE_MASK and NCSI_ATTR_CHANNEL_MASK attributes
respectively. If one of these whitelists is set only packages or
channels matching the whitelist are considered for the channel queue in
ncsi_choose_active_channel().

These commands may also use the NCSI_ATTR_MULTI_FLAG to signal that
multiple packages or channels may be configured simultaneously. NCSI
hardware arbitration (HWA) must be available in order to enable
multi-package mode. Multi-channel mode is always available.

If the NCSI_ATTR_CHANNEL_ID attribute is present in the
NCSI_CMD_SET_CHANNEL_MASK command the it sets the preferred channel as
with the NCSI_CMD_SET_INTERFACE command. The combination of preferred
channel and channel whitelist defines a primary channel and the allowed
failover channels.
If the NCSI_ATTR_MULTI_FLAG attribute is also present then the preferred
channel is configured for Tx/Rx and the other channels are enabled only
for Rx.

Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-17 21:09:49 -08:00
Samuel Mendoza-Jonas
2878a2cfe5 net/ncsi: Reset channel state in ncsi_start_dev()
When the NCSI driver is stopped with ncsi_stop_dev() the channel
monitors are stopped and the state set to "inactive". However the
channels are still configured and active from the perspective of the
network controller. We should suspend each active channel but in the
context of ncsi_stop_dev() the transmit queue has been or is about to be
stopped so we won't have time to do so.

Instead when ncsi_start_dev() is called if the NCSI topology has already
been probed then call ncsi_reset_dev() to suspend any channels that were
previously active. This resets the network controller to a known state,
provides an up to date view of channel link state, and makes sure that
mode flags such as NCSI_MODE_TX_ENABLE are properly reset.

In addition to ncsi_start_dev() use ncsi_reset_dev() in ncsi-netlink.c
to update the channel configuration more cleanly.

Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-17 21:09:49 -08:00
Samuel Mendoza-Jonas
0b970e1b04 net/ncsi: Don't mark configured channels inactive
The concepts of a channel being 'active' and it having link are slightly
muddled in the NCSI driver. Tweak this slightly so that
NCSI_CHANNEL_ACTIVE represents a channel that has been configured and
enabled, and NCSI_CHANNEL_INACTIVE represents a de-configured channel.
This distinction is important because a channel can be 'active' but have
its link down; in this case the channel may still need to be configured
so that it may receive AEN link-state-change packets.

Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-17 21:09:49 -08:00
Samuel Mendoza-Jonas
cd09ab095c net/ncsi: Don't deselect package in suspend if active
When a package is deselected all channels of that package cease
communication. If there are other channels active on the package of the
suspended channel this will disable them as well, so only send a
deselect-package command if no other channels are active.

Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-17 21:09:49 -08:00
Samuel Mendoza-Jonas
8e13f70be0 net/ncsi: Probe single packages to avoid conflict
Currently the NCSI driver sends a select-package command to all possible
packages simultaneously to discover what packages are available. However
at this stage in the probe process the driver does not know if
hardware arbitration is available: if it isn't then this process could
cause collisions on the RMII bus when packages try to respond.

Update the probe loop to probe each package one by one, and once
complete check if HWA is universally supported.

Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-17 21:09:49 -08:00
Samuel Mendoza-Jonas
60ab49bfe4 net/ncsi: Don't enable all channels when HWA available
NCSI hardware arbitration allows multiple packages to be enabled at once
and share the same wiring. If the NCSI driver recognises that HWA is
available it unconditionally enables all packages and channels; but that
is a configuration decision rather than something required by HWA.
Additionally the current implementation will not failover on link events
which can cause connectivity to be lost unless the interface is manually
bounced.

Retain basic HWA support but remove the separate configuration path to
enable all channels, leaving this to be handled by a later
implementation.

Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-17 21:09:49 -08:00
Vijay Khemka
cb10c7c0df net/ncsi: Add NCSI Broadcom OEM command
This patch adds OEM Broadcom commands and response handling. It also
defines OEM Get MAC Address handler to get and configure the device.

ncsi_oem_gma_handler_bcm: This handler send NCSI broadcom command for
getting mac address.
ncsi_rsp_handler_oem_bcm: This handles response received for all
broadcom OEM commands.
ncsi_rsp_handler_oem_bcm_gma: This handles get mac address response and
set it to device.

Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-17 22:14:54 -07:00
Justin.Lee1@Dell.com
9771b8ccdf net/ncsi: Extend NC-SI Netlink interface to allow user space to send NC-SI command
The new command (NCSI_CMD_SEND_CMD) is added to allow user space application
to send NC-SI command to the network card.
Also, add a new attribute (NCSI_ATTR_DATA) for transferring request and response.

The work flow is as below.

Request:
User space application
	-> Netlink interface (msg)
	-> new Netlink handler - ncsi_send_cmd_nl()
	-> ncsi_xmit_cmd()

Response:
Response received - ncsi_rcv_rsp()
	-> internal response handler - ncsi_rsp_handler_xxx()
	-> ncsi_rsp_handler_netlink()
	-> ncsi_send_netlink_rsp ()
	-> Netlink interface (msg)
	-> user space application

Command timeout - ncsi_request_timeout()
	-> ncsi_send_netlink_timeout ()
	-> Netlink interface (msg with zero data length)
	-> user space application

Error:
Error detected
	-> ncsi_send_netlink_err ()
	-> Netlink interface (err msg)
	-> user space application

Signed-off-by: Justin Lee <justin.lee1@dell.com>
Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-15 22:00:59 -07:00
Vijay Khemka
fb4ee67529 net/ncsi: Add NCSI OEM command support
This patch adds OEM commands and response handling. It also defines OEM
command and response structure as per NCSI specification along with its
handlers.

ncsi_cmd_handler_oem: This is a generic command request handler for OEM
commands
ncsi_rsp_handler_oem: This is a generic response handler for OEM commands

Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Reviewed-by: Justin Lee <justin.lee1@dell.com>
Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-05 14:54:47 -07:00
YueHaibing
8bad008e79 net/ncsi: remove duplicated include from ncsi-netlink.c
Remove duplicated include.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-08-29 19:10:40 -07:00
Samuel Mendoza-Jonas
3d0371b313 net/ncsi: Fixup .dumpit message flags and ID check in Netlink handler
The ncsi_pkg_info_all_nl() .dumpit handler is missing the NLM_F_MULTI
flag, causing additional package information after the first to be lost.
Also fixup a sanity check in ncsi_write_package_info() to reject out of
range package IDs.

Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-08-22 21:39:08 -07:00
Joel Stanley
6e42a3f5cd net/ncsi: Use netdev_dbg for debug messages
This moves all of the netdev_printk(KERN_DEBUG, ...) messages over to
netdev_dbg.

As Joe explains:

> netdev_dbg is not included in object code unless
> DEBUG is defined or CONFIG_DYNAMIC_DEBUG is set.
> And then, it is not emitted into the log unless
> DEBUG is set or this specific netdev_dbg is enabled
> via the dynamic debug control file.

Which is what we're after in this case.

Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-20 07:26:58 +09:00
Joel Stanley
5d3b146736 net/ncsi: Drop no more channels message
This does not provide useful information. As the ncsi maintainer said:

 > either we get a channel or broadcom has gone out to lunch

Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-20 07:26:58 +09:00
Joel Stanley
87975a0117 net/ncsi: Silence debug messages
In normal operation we see this series of messages as the host drives
the network device:

 ftgmac100 1e660000.ethernet eth0: NCSI: LSC AEN - channel 0 state down
 ftgmac100 1e660000.ethernet eth0: NCSI: suspending channel 0
 ftgmac100 1e660000.ethernet eth0: NCSI: configuring channel 0
 ftgmac100 1e660000.ethernet eth0: NCSI: channel 0 link down after config
 ftgmac100 1e660000.ethernet eth0: NCSI interface down
 ftgmac100 1e660000.ethernet eth0: NCSI: LSC AEN - channel 0 state up
 ftgmac100 1e660000.ethernet eth0: NCSI: configuring channel 0
 ftgmac100 1e660000.ethernet eth0: NCSI interface up
 ftgmac100 1e660000.ethernet eth0: NCSI: LSC AEN - channel 0 state down
 ftgmac100 1e660000.ethernet eth0: NCSI: suspending channel 0
 ftgmac100 1e660000.ethernet eth0: NCSI: configuring channel 0
 ftgmac100 1e660000.ethernet eth0: NCSI: channel 0 link down after config
 ftgmac100 1e660000.ethernet eth0: NCSI interface down
 ftgmac100 1e660000.ethernet eth0: NCSI: LSC AEN - channel 0 state up
 ftgmac100 1e660000.ethernet eth0: NCSI: configuring channel 0
 ftgmac100 1e660000.ethernet eth0: NCSI interface up

This makes all of these messages netdev_dbg. They are still useful to
debug eg. misbehaving network device firmware, but we do not need them
filling up the kernel logs in normal operation.

Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-20 07:26:58 +09:00
Samuel Mendoza-Jonas
b094961882 net/ncsi: Avoid GFP_KERNEL in response handler
ncsi_rsp_handler_gc() allocates the filter arrays using GFP_KERNEL in
softirq context, causing the below backtrace. This allocation is only a
few dozen bytes during probing so allocate with GFP_ATOMIC instead.

[   42.813372] BUG: sleeping function called from invalid context at mm/slab.h:416
[   42.820900] in_atomic(): 1, irqs_disabled(): 0, pid: 213, name: kworker/0:1
[   42.827893] INFO: lockdep is turned off.
[   42.832023] CPU: 0 PID: 213 Comm: kworker/0:1 Tainted: G        W       4.13.16-01441-gad99b38 #65
[   42.841007] Hardware name: Generic DT based system
[   42.845966] Workqueue: events ncsi_dev_work
[   42.850251] [<8010a494>] (unwind_backtrace) from [<80107510>] (show_stack+0x20/0x24)
[   42.858046] [<80107510>] (show_stack) from [<80612770>] (dump_stack+0x20/0x28)
[   42.865309] [<80612770>] (dump_stack) from [<80148248>] (___might_sleep+0x230/0x2b0)
[   42.873241] [<80148248>] (___might_sleep) from [<80148334>] (__might_sleep+0x6c/0xac)
[   42.881129] [<80148334>] (__might_sleep) from [<80240d6c>] (__kmalloc+0x210/0x2fc)
[   42.888737] [<80240d6c>] (__kmalloc) from [<8060ad54>] (ncsi_rsp_handler_gc+0xd0/0x170)
[   42.896770] [<8060ad54>] (ncsi_rsp_handler_gc) from [<8060b454>] (ncsi_rcv_rsp+0x16c/0x1d4)
[   42.905314] [<8060b454>] (ncsi_rcv_rsp) from [<804d86c8>] (__netif_receive_skb_core+0x3c8/0xb50)
[   42.914158] [<804d86c8>] (__netif_receive_skb_core) from [<804d96cc>] (__netif_receive_skb+0x20/0x7c)
[   42.923420] [<804d96cc>] (__netif_receive_skb) from [<804de4b0>] (netif_receive_skb_internal+0x78/0x6a4)
[   42.932931] [<804de4b0>] (netif_receive_skb_internal) from [<804df980>] (netif_receive_skb+0x78/0x158)
[   42.942292] [<804df980>] (netif_receive_skb) from [<8042f204>] (ftgmac100_poll+0x43c/0x4e8)
[   42.950855] [<8042f204>] (ftgmac100_poll) from [<804e094c>] (net_rx_action+0x278/0x4c4)
[   42.958918] [<804e094c>] (net_rx_action) from [<801016a8>] (__do_softirq+0xe0/0x4c4)
[   42.966716] [<801016a8>] (__do_softirq) from [<8011cd9c>] (do_softirq.part.4+0x50/0x78)
[   42.974756] [<8011cd9c>] (do_softirq.part.4) from [<8011cebc>] (__local_bh_enable_ip+0xf8/0x11c)
[   42.983579] [<8011cebc>] (__local_bh_enable_ip) from [<804dde08>] (__dev_queue_xmit+0x260/0x890)
[   42.992392] [<804dde08>] (__dev_queue_xmit) from [<804df1f0>] (dev_queue_xmit+0x1c/0x20)
[   43.000689] [<804df1f0>] (dev_queue_xmit) from [<806099c0>] (ncsi_xmit_cmd+0x1c0/0x244)
[   43.008763] [<806099c0>] (ncsi_xmit_cmd) from [<8060dc14>] (ncsi_dev_work+0x2e0/0x4c8)
[   43.016725] [<8060dc14>] (ncsi_dev_work) from [<80133dfc>] (process_one_work+0x214/0x6f8)
[   43.024940] [<80133dfc>] (process_one_work) from [<80134328>] (worker_thread+0x48/0x558)
[   43.033070] [<80134328>] (worker_thread) from [<8013ba80>] (kthread+0x130/0x174)
[   43.040506] [<8013ba80>] (kthread) from [<80102950>] (ret_from_fork+0x14/0x24)

Fixes: 062b3e1b6d ("net/ncsi: Refactor MAC, VLAN filters")
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-03 10:42:07 -04:00
David S. Miller
9c54aeb03a Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Filling in the padding slot in the bpf structure as a bug fix in 'ne'
overlapped with actually using that padding area for something in
'net-next'.

Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-03 09:31:58 -04:00
Samuel Mendoza-Jonas
0f51f3582f net/ncsi: Fix array size in dumpit handler
With CONFIG_CC_STACKPROTECTOR enabled the kernel panics as below when
parsing a NCSI_CMD_PKG_INFO command:

[  150.149711] Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: 805cff08
[  150.149711]
[  150.159919] CPU: 0 PID: 1301 Comm: ncsi-netlink Not tainted 4.13.16-468cbec6d2c91239332cb91b1f0a73aafcb6f0c6 #1
[  150.170004] Hardware name: Generic DT based system
[  150.174852] [<80109930>] (unwind_backtrace) from [<80106bc4>] (show_stack+0x20/0x24)
[  150.182641] [<80106bc4>] (show_stack) from [<805d36e4>] (dump_stack+0x20/0x28)
[  150.189888] [<805d36e4>] (dump_stack) from [<801163ac>] (panic+0xdc/0x278)
[  150.196780] [<801163ac>] (panic) from [<801162cc>] (__stack_chk_fail+0x20/0x24)
[  150.204111] [<801162cc>] (__stack_chk_fail) from [<805cff08>] (ncsi_pkg_info_all_nl+0x244/0x258)
[  150.212912] [<805cff08>] (ncsi_pkg_info_all_nl) from [<804f939c>] (genl_lock_dumpit+0x3c/0x54)
[  150.221535] [<804f939c>] (genl_lock_dumpit) from [<804f873c>] (netlink_dump+0xf8/0x284)
[  150.229550] [<804f873c>] (netlink_dump) from [<804f8d44>] (__netlink_dump_start+0x124/0x17c)
[  150.237992] [<804f8d44>] (__netlink_dump_start) from [<804f9880>] (genl_rcv_msg+0x1c8/0x3d4)
[  150.246440] [<804f9880>] (genl_rcv_msg) from [<804f9174>] (netlink_rcv_skb+0xd8/0x134)
[  150.254361] [<804f9174>] (netlink_rcv_skb) from [<804f96a4>] (genl_rcv+0x30/0x44)
[  150.261850] [<804f96a4>] (genl_rcv) from [<804f7790>] (netlink_unicast+0x198/0x234)
[  150.269511] [<804f7790>] (netlink_unicast) from [<804f7ffc>] (netlink_sendmsg+0x368/0x3b0)
[  150.277783] [<804f7ffc>] (netlink_sendmsg) from [<804abea4>] (sock_sendmsg+0x24/0x34)
[  150.285625] [<804abea4>] (sock_sendmsg) from [<804ac1dc>] (___sys_sendmsg+0x244/0x260)
[  150.293556] [<804ac1dc>] (___sys_sendmsg) from [<804ad98c>] (__sys_sendmsg+0x5c/0x9c)
[  150.301400] [<804ad98c>] (__sys_sendmsg) from [<804ad9e4>] (SyS_sendmsg+0x18/0x1c)
[  150.308984] [<804ad9e4>] (SyS_sendmsg) from [<80102640>] (ret_fast_syscall+0x0/0x3c)
[  150.316743] ---[ end Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: 805cff08

This turns out to be because the attrs array in ncsi_pkg_info_all_nl()
is initialised to a length of NCSI_ATTR_MAX which is the maximum
attribute number, not the number of attributes.

Fixes: 955dc68cb9 ("net/ncsi: Add generic netlink family")
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-31 15:57:54 -04:00
YueHaibing
c1c9a3c966 net: remove unnecessary genlmsg_cancel() calls
the message be freed immediately, no need to trim it
back to the previous size.

Inspired by commit 7a9b3ec1e1 ("nl80211: remove unnecessary genlmsg_cancel() calls")

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-29 09:53:38 -04:00
Dan Carpenter
990a9d4975 net/ncsi: prevent a couple array underflows
We recently refactored this code and introduced a static checker
warning.  Smatch complains that if cmd->index is zero then we would
underflow the arrays.  That's obviously true.

The question is whether we prevent cmd->index from being zero at a
different level.  I've looked at the code and I don't immediately see
a check for that.

Fixes: 062b3e1b6d ("net/ncsi: Refactor MAC, VLAN filters")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-05-17 16:27:39 -04:00
Samuel Mendoza-Jonas
062b3e1b6d net/ncsi: Refactor MAC, VLAN filters
The NCSI driver defines a generic ncsi_channel_filter struct that can be
used to store arbitrarily formatted filters, and several generic methods
of accessing data stored in such a filter.
However in both the driver and as defined in the NCSI specification
there are only two actual filters: VLAN ID filters and MAC address
filters. The splitting of the MAC filter into unicast, multicast, and
mixed is also technically not necessary as these are stored in the same
location in hardware.

To save complexity, particularly in the set up and accessing of these
generic filters, remove them in favour of two specific structs. These
can be acted on directly and do not need several generic helper
functions to use.

This also fixes a memory error found by KASAN on ARM32 (which is not
upstream yet), where response handlers accessing a filter's data field
could write past allocated memory.

[  114.926512] ==================================================================
[  114.933861] BUG: KASAN: slab-out-of-bounds in ncsi_configure_channel+0x4b8/0xc58
[  114.941304] Read of size 2 at addr 94888558 by task kworker/0:2/546
[  114.947593]
[  114.949146] CPU: 0 PID: 546 Comm: kworker/0:2 Not tainted 4.16.0-rc6-00119-ge156398bfcad #13
...
[  115.170233] The buggy address belongs to the object at 94888540
[  115.170233]  which belongs to the cache kmalloc-32 of size 32
[  115.181917] The buggy address is located 24 bytes inside of
[  115.181917]  32-byte region [94888540, 94888560)
[  115.192115] The buggy address belongs to the page:
[  115.196943] page:9eeac100 count:1 mapcount:0 mapping:94888000 index:0x94888fc1
[  115.204200] flags: 0x100(slab)
[  115.207330] raw: 00000100 94888000 94888fc1 0000003f 00000001 9eea2014 9eecaa74 96c003e0
[  115.215444] page dumped because: kasan: bad access detected
[  115.221036]
[  115.222544] Memory state around the buggy address:
[  115.227384]  94888400: fb fb fb fb fc fc fc fc 04 fc fc fc fc fc fc fc
[  115.233959]  94888480: 00 00 00 fc fc fc fc fc 00 04 fc fc fc fc fc fc
[  115.240529] >94888500: 00 00 04 fc fc fc fc fc 00 00 04 fc fc fc fc fc
[  115.247077]                                             ^
[  115.252523]  94888580: 00 04 fc fc fc fc fc fc 06 fc fc fc fc fc fc fc
[  115.259093]  94888600: 00 00 06 fc fc fc fc fc 00 00 04 fc fc fc fc fc
[  115.265639] ==================================================================

Reported-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-17 13:50:58 -04:00
Colin Ian King
8daf1a2d7e net/ncsi: check for null return from call to nla_nest_start
The call to nla_nest_start calls nla_put which can lead to a NULL
return so it's possible for attr to become NULL and we can potentially
get a NULL pointer dereference on attr.  Fix this by checking for
a NULL return.

Detected by CoverityScan, CID#1466125 ("Dereference null return")

Fixes: 955dc68cb9 ("net/ncsi: Add generic netlink family")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-27 10:38:26 -04:00
Dan Carpenter
054f34da60 net/ncsi: unlock on error in ncsi_set_interface_nl()
There are two error paths which are missing unlocks in this function.

Fixes: 955dc68cb9 ("net/ncsi: Add generic netlink family")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-08 21:49:58 -05:00
Dan Carpenter
50db64b090 net/ncsi: use kfree_skb() instead of kfree()
We're supposed to use kfree_skb() to free these sk_buffs.

Fixes: 955dc68cb9 ("net/ncsi: Add generic netlink family")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-08 21:49:58 -05:00
Samuel Mendoza-Jonas
955dc68cb9 net/ncsi: Add generic netlink family
Add a generic netlink family for NCSI. This supports three commands;
NCSI_CMD_PKG_INFO which returns information on packages and their
associated channels, NCSI_CMD_SET_INTERFACE which allows a specific
package or package/channel combination to be set as the preferred
choice, and NCSI_CMD_CLEAR_INTERFACE which clears any preferred setting.

Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-05 10:43:37 -05:00
Samuel Mendoza-Jonas
75e8e15635 net/ncsi: Don't take any action on HNCDSC AEN
The current HNCDSC handler takes the status flag from the AEN packet and
will update or change the current channel based on this flag and the
current channel status.

However the flag from the HNCDSC packet merely represents the host link
state. While the state of the host interface is potentially interesting
information it should not affect the state of the NCSI link. Indeed the
NCSI specification makes no mention of any recommended action related to
the host network controller driver state.

Update the HNCDSC handler to record the host network driver status but
take no other action.

Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-18 14:50:11 -05:00