Enforce correct device sequencing when configuring a new
audio route when there is an existing active audio route(s).
This patch fixed recording noise issue while playback is active.
We have some registers which require the device to be in full shutdown
or to enter full shutdown before the register settings will take effect.
Currently the driver is not shutting down the device when a new audio
route is created. If a new audio route is made active while there is
already an active audio route, then the required register sequencing is
violated. A hardware shutdown toggle when creating a new audio route
corrects the sequencing error. The device must remain in hardware
shutdown for 40ms to allow the internal hardware core to fully shutdown.
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Acked-by: Anish Kumar <anish.kumar@maximintegrated.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To manage DSP we need to create processing pipeline and on cleanup destroy
them. So we add create and destroy routines for pipelines The pipelines need
to to be executed so we add pipeline run and stop routines
All these send required IPCs to DSP using IPC routines added earlier
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A module needs to be instantiated and then connected with other modules. On
cleanup we need to disconnect the module.
This is achieved by helpers module init, bind and unbind which are added
here
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SRC and converter modules are required to do frequency and channel
conversion in DSP. Both take base module configuration and additional SRC
and converter parameters. The helpers here are added to calculate the values
for these modules
Signed-off-by: Hardik T Shah <hardik.t.shah@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds helper functions to calculate parameters required for base module
format and copier module. A generic module is modelled by base module.
Copier module is responsible for getting/sending data to FE (host DMAs) and
BE (link HDA DMA, SSP, PDM)
This also ads module pin management helpers which help in finding pins to
use or freeing them up
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of defining own acpi header, use the available acpi
header defined in acpi framework.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sampling rate type needs to be u32 instead of u8, nhlt wav format
description expected u32 for rate, passing u8 will fetch NULL
config in skl_get_ep_blob().
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch was generated using fixed coccinelle semantic patch
scripts/coccinelle/api/memdup.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2014320
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch was generated using fixed coccinelle semantic patch
scripts/coccinelle/api/memdup.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2014320
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the TLV topology structure is targeted at only supporting the
DB scale data. This patch extends support for the other TLV types so they
can be easily added at a later stage.
TLV structure is moved to common topology control header since it's a
common field for controls and can be processed in a general way.
Users must set a proper access flag for a control since it's used to
decide if the TLV field is valid and if a TLV callback is needed.
Removed the following fields from topology TLV struct:
- size/count: type can decide the size.
- numid: not needed to initialize TLV for kcontrol.
- data: replaced by the type specific struct.
Added TLV structure to generic control header and removed TLV structure
from mixer control.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A lot of small fixes here, a few to the core:
- Fix for binding DAPM stream widgets on devices with prefixes assigned
to them
- Minor fixes for the newly added topology interfaces
- Locking and memory leak fixes for DAPM
- Driver specific fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVsnNFAAoJECTWi3JdVIfQH9cH/1ddueDFikvXSCyntuJcHAwJ
a7X5kCVdegMnaMK5fnAbTlJBpDIX/F1UBvsFQQ38eKWeneP44XnkXeh/32fGJzQO
L730dqy0tkgQdWJkQg0yxaP5/k0BfhnXeRc3ATUG3LBgUBrWRYLTIvaM+G+H3Kf5
K88QL7cKmeY0Kt6+cms3nnBj9x5oFgbHIW7Y3K/pza+XPVecZ7N3/5gpV+VQDUXh
Oz3cZOsC5h4+IpxkOrLXY7zgLvrt/HfRTO2QF/3Ntub81anAk190pVAquM+r/CTn
tQ3sPNGLglQ4VRXNP6yBKJOp5CUTBLt5XWlJ+Kg9p2OiiuOPla4wkhuGDS5AM64=
=nJJl
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v4.2-rc3' into asoc-fix-topology
ASoC: Fixes for v4.2
A lot of small fixes here, a few to the core:
- Fix for binding DAPM stream widgets on devices with prefixes assigned
to them
- Minor fixes for the newly added topology interfaces
- Locking and memory leak fixes for DAPM
- Driver specific fixes
Some widgets may need sorting within, So add this support in topology.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Existing implementation checks all divider values and tracks
'red' proximity value for the frequency.
But as divider array is monotonically increasing the first
divider that gives DMIC rate in 3MHz range is the best one
we should use. No need for 'red' zone tracking.
Additionally make sure that DMIC frequency is higher 1MHz.
Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Acked-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch introduces the use of managed resource function
devm_clk_get instead of clk_get and removes corresponding calls
to clk_put in the probe and remove functions.
To be compatible with the change various gotos are replaced with
direct returns, and unneeded labels are dropped.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
For TLVs with only a single entry it is not necessary to use a range
container. Use DECLARE_TLV_DB_LINEAR() directly instead of a combination of
TLV_DB_RANGE_HEAD() and TLV_DB_LINEAR_ITEM().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
For TLVs with only a single entry it is not necessary to use a range
container. Use DECLARE_TLV_DB_SCALE() directly instead of a combination of
TLV_DB_RANGE_HEAD() and TLV_DB_SCALE_ITEM().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
For TLVs with only a single entry it is not necessary to use a range
container. Use DECLARE_TLV_DB_SCALE() directly instead of a combination of
TLV_DB_RANGE_HEAD() and TLV_DB_SCALE_ITEM().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
I2S2_DAC pin can be used for I2S or GPIO. We should set it as GPIO
if we use GPIO5 as DMIC1 data pin.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So technically there's no need for a driver to export
the OF table since currently it's not used.
In fact, the I2C device ID table is mandatory for I2C drivers since
a i2c_device_id is passed to the driver's probe function even if the
I2C core used the OF table to match the driver.
And since the I2C core uses different tables, OF-only drivers needs to
have duplicated data that has to be kept in sync and also the dev node
compatible manufacturer prefix is stripped when reporting the MODALIAS.
To avoid the above, the I2C core behavior may be changed in the future
to not require an I2C device table for OF-only drivers and report the
OF module alias. So, it's better to also export the OF table to prevent
breaking module autoloading if that happens.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The readable registers are in consecutive ranges:
0x01 ~ 0x03, 0x0D ~ 0xD1, 0xFF
So simplify the implementation by specifying a range of consecutive values
in a single case label.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
uni_player_dai_ops is not used outside of this file so it should be static.
Fixes the following sparse warning:
sound/soc/sti/uniperif_player.c:959:30: warning: symbol
'uni_player_dai_ops' was not declared. Should it be static?
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
base referes to a iomem region, so it should have the __iomem annotation.
Fixes the following warnings from sparse:
sound/soc/sti/sti_uniperif.c:169:19: warning: incorrect type in
assignment (different address spaces)
sound/soc/sti/sti_uniperif.c:169:19: expected void *base
sound/soc/sti/sti_uniperif.c:169:19: got void [noderef] <asn:2>*
sound/soc/sti/uniperif_player.c:104:18: warning: incorrect type in
argument 1 (different address spaces)
sound/soc/sti/uniperif_player.c:104:18: expected void const volatile
[noderef] <asn:2>*addr
sound/soc/sti/uniperif_player.c:104:18: got void *
[...]
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_of_parse_ctu() is not used outside this file so it can be static.
Fixes the following sparse warning:
sound/soc/sh/rcar/ctu.c:72:6: warning: symbol 'rsnd_of_parse_ctu' was
not declared. Should it be static?
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ipq806x_data is not used outside this file, so it can be static.
Fixes the following sparse warning:
sound/soc/qcom/lpass-ipq806x.c:76:22: warning: symbol 'ipq806x_data'
was not declared. Should it be static?
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add initialization for sst_byt.dev at init stage, which fix the
'NULL device *' warning issues.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add initialization for sst_hsw.dev at init stage, which fix the
'NULL device *' warning issues.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The max98095_access table is used for look up readable/writable
attributes of registers. The readable/writable/volatile registers are
mostly in continuous ranges, so we can replace the max98095_access table
entirely by using case range.
Below is a summary of the readable/writeable/volatile registers:
readable registers:
0x01 ~ 0x97, 0xFF
writeable registers:
0x0F ~ 0x97
volatile registers:
0x00 ~ 0x0E, 0x98 ~ 0xFF
This patch reworks the implement for .readable and .volatile and also add
implementation for .writable callback.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The max98088_access table is used for look up readable/writable/volatile
attributes of registers. The readable/writable/volatile registers are
mostly in continuous ranges, so we can replace the max98088_access table
entirely by using case range.
Below is a summary of the readable/writeable/volatile registers:
readable registers:
0x00 ~ 0xC9, 0xFF
writeable registers:
0x03 ~ 0xC9
volatile registers:
0x00 ~ 0x03, 0xFF
Note, 0x00 should be read-only according to the datasheet.
This patch reworks the implement for .readable and .volatile and also add
implementation for .writable callback.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add helper iterator macros for iterating over the source and sink paths of
widget. This will make it easier to change the implementation later on.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
When running dapm_dai_get_connected_widgets() currently in
is_connected_{input,output}_ep() for each widget that gets added the array
is resized and the code also loops over all existing entries to avoid
adding a widget multiple times.
The former can be avoided by collecting the widgets in a linked list and
only once we have all widgets allocate the array.
The later can be avoided by changing when the widget is added. Currently it
is added when walking the neighbor lists of a widget. Since a widget can be
neighbors with multiple other widgets it could get added twice and hence
the check is necessary. But the main body of is_connected_{input,output}_ep
is guaranteed to be only executed at most once per widget. So adding the
widget to the list at the beginning of the function automatically makes
sure that each widget gets only added once. The only difference is that
using this method the starting point itself will also end up on the list,
but it can easily be skipped when creating the array.
Overall this reduces the code size and speeds things slightly up.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
list_first_entry() always returns non NULL and since the code previously
checked that list is not empty it will also be a valid pointer. Furthermore
a path has always a sink or a source widget. So both checks are redundant
and can be removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
It's safe to call gpiod_set_value() with NULL desc.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If devm_gpiod_get_optional() return ERR_PTR, it means something wrong
so request gpio fails. We had better return error in such case.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
CS4265_INT_STATUS was missed in cs4265_readable_register, fix it.
The register 0x01 ~ 0x12 are readable, use
CS4265_CHIP_ID ... CS4265_SPDIF_CTL2 syntax for better readability.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The settings in current code does not match the datasheet, fix it.
DAC Control - Address 03h
DAC Digital Interface Format (Bits 5:4)
DAC_DIF1 DAC_DIF0 Description
0 0 Left Justified, up to 24-bit data (default)
0 1 I²S, up to 24-bit data
1 0 Right-Justified, 16-bit Data
1 1 Right-Justified, 24-bit Data
Transmitter Control 2 - Address 12h
Transmitter Digital Interface Format (Bits 7:6)
Tx_DIF1 Tx_DIF0 Description Format Figure
0 0 Left Justified, up to 24-bit data (default)
0 1 I²S, up to 24-bit data
1 0 Right-Justified, 16-bit Data
1 1 Right-Justified, 24-bit Data
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Added INT343B ACPI ID for the SSM4567 codec
Signed-off-by: Harsha Priya <harshapriya.n@intel.com>
Signed-off-by: M Naveen <naveen.m@intel.com>
Signed-off-by: M R Sathya Prakash <sathya.prakash.m.r@intel.com>
Acked-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This checking is done by regmap_get_i2c_bus() which is called in
devm_regmap_init_i2c().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Slightly improve the logic for de-emphasis sampling rate selection by break
out the loop if the rate is matched.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The de-emphasis sampling rate selection is controlled by BIT[3:4] of
PCM1681_DEEMPH_CONTROL register. Do proper left shift to set it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Marek Belisko <marek.belisko@streamunlimited.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Currently, rl6231_pll_calc provide a working PLL parameters for
given freq_in and freq_out. However, in some cases it is not the
perfect parameter. For example if freq_in = 19200000 and freq_out
= 24576000, the calculated parameter will gengrate 24.5647 MHz
which is not exactly the same as what we need. But the PLL can
output 24.576 MHz as exactly what we expect if we set the best
PLL parameter.
To improve it, we put the best match parameters in a preset table.
We can search the preset table first, if there is no preset parameter
for the given freq_in and freq_out, we can still calculate a working
PLL parameter.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This helper function will be used by the Skylake driver for dsp and
ipc initialization if processing pipe capability is supported.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Non-HD Audio Endpoint Description table contains the link
configuration information for the DSP. This is specific to Non HDA
links only, like I2s and PDM
Skylake driver will use NHLT table to retrieve the configuration based
on the link type, format, channel and rate. This configuration is
passed to DSP FW
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the new snd_ac97_reset() helper and the reset functionality provided by
snd_soc_new_ac97_codec() to perform the device reset rather than
open-coding it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the new snd_ac97_reset() helper and the reset functionality provided by
snd_soc_new_ac97_codec() to perform the device reset rather than
open-coding it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the new snd_ac97_reset() helper and the reset functionality provided by
snd_soc_new_ac97_codec() to perform the device reset rather than
open-coding it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the new snd_ac97_reset() helper and the reset functionality provided by
snd_soc_new_ac97_codec() to perform the device reset rather than
open-coding it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the new snd_ac97_reset() helper function to perform the reset and
verify the device ID.
Unfortunately the reset can't be done in snd_soc_new_ac97_codec() due to
the special requirements in order to support the non-standard 16-bit slot
mode of the ad1980.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
AC97 devices need to be initially reset before they can be used. Currently
each driver does this on its own.
Add support for resetting the device to core in snd_soc_new_ac97_codec().
If the caller supplies a device ID and device ID mask the function will
reset the device and verify that it has the correct ID, if it does not a
error is returned.
This will allow to remove custom code with similar functionality from
individual drivers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Slightly improve the logic for de-emphasis sampling rate selection by break
out the loop if the rate is matched.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The latest valid register is TAS2552_VBAT_DATA.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Dan Murphy<dmurphy@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It's safe to call gpiod_set_value_cansleep() with NULL desc.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
CS42L73_SP_3ST is BIT(7), so the mask field is wrong. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It's safe to call gpiod_set_value_cansleep() with NULL desc.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the datasheet, the CS35L32_SDOUT_3ST is BIT(3).
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds suspend/resume callbacks, which are common for each DAI.
To be able to continue the last playback/capture after resume
when suspend was done during a playback/capture, in the callbacks
we do backup/restore of registers which were set before prepare stage.
Registers to be backup/restore are defined in a backup list array.
Signed-off-by: Koro Chen <koro.chen@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PWR_DWN is Bit 7, so current code does not set the PWR_DWN bit. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It's safe to call gpiod_set_value_cansleep() with NULL desc.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regmap_write in ssm4567_set_dai_fmt accidentally clears the
TDM_BCLKS field which was set earlier by ssm4567_set_tdm_slot.
This patch fixes it by using regmap_update_bits with proper mask.
Signed-off-by: Ben Zhang <benzh@chromium.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Currently, below code actually does not update any bit because
SGTL5000_SMALL_POP is 0.
snd_soc_update_bits(codec, SGTL5000_CHIP_REF_CTRL, SGTL5000_SMALL_POP, 1);
The SGTL5000_SMALL_POP should be BIT(0) rather than 0, fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-By: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When creating a new widget from a template the name string of the template
is duplicated for the newly created widget. This is necessary because in
some cases the string might be stored on the stack or other volatile
memory locations.
But most of the time the string is static const data, which means it is
possible to use it directly without having to worry that it might get freed
or changed.
Use kstrdup_const() to handle duplicating the string. This function is
capable of detecting whether a string is immutable and if it is returns the
input without duplicating it. This will slightly reduce the runtime memory
footprint of DAPM and also speed up initialization.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_tplg_widget_remove_all() has a verbatim copy of an older version of
the widget freeing code from dapm_free_widgets(). Add a new helper function
that takes care of freeing a widget and use it in both places.
This removes the duplicated code and also makes sure that future changes to
the widget freeing code only have to be made in one location.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The kirkwood audio subsystem presents 2 PCM's for one source.
Streaming on a second PCM while the first one is active
cuts this last one.
Then, ending the last stream gives a kernel trap in free_irq().
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a stray '!' which means the condition is never true.
Fixes: f3bd847eb0 ('ASoC: sti: Add uniperipheral dai driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Debug prints are seldom useful and this one has an annoying thing where
it reads one space beyond the end of the array on error.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
84e95355602c("ASoC: rsnd: show debug message for SSI/SRC/DVC connection")
added debug message on rsnd_dai_connect(), but the relationship of
parameter check was absurdity. This patch tidyup it.
It is reported via Smatch/Dan
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit fdb6eb0a12 ("ASoC: dapm: Modify widget stream name according to
prefix") fixed the case where a DAPM route between a DAI widget and a
DAC/ADC/AIF widget with a matching stream name was not created when the
DAPM context was using a prefix.
Unfortunately the patch introduced a few issues on its own like leaking the
dynamically allocated stream name memory and also not checking whether the
allocation succeeded in the first place.
It is also incomplete in that it still does not handle the case where
stream name of the widget is a substring of the stream name of the DAI,
which is explicitly allowed and works fine if no DAPM prefix is used.
Revert the commit and take a slightly different approach to solving the
issue. Instead of comparing the widget's stream name to the name of the DAI
widget compare it to the stream name of the DAI widget. The stream name of
the DAI widget is identical to the name of the DAI widget except that it
wont have the DAPM prefix added. So this approach behaves identical
regardless to whether the DAPM context uses a prefix or not.
We don't have to worry about potentially matching with a widget with the
same stream name, but from a different DAPM context with a different
prefix, since the code already makes sure that both the DAI widget and the
matched widget are from the same DAPM context.
Fixes: fdb6eb0a12 ("ASoC: dapm: Modify widget stream name according to prefix")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
s390 allmodconfig:
sound/soc/codecs/cs4349.c: In function 'cs4349_i2c_probe':
sound/soc/codecs/cs4349.c:300: error: implicit declaration of function 'devm_gpiod_get_optional'
sound/soc/codecs/cs4349.c:301: error: 'GPIOD_OUT_LOW' undeclared (first use in this function)
sound/soc/codecs/cs4349.c:301: error: (Each undeclared identifier is reported only once
sound/soc/codecs/cs4349.c:301: error: for each function it appears in.)
sound/soc/codecs/cs4349.c:306: error: implicit declaration of function 'gpiod_set_value_cansleep'
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The struct cs4349_platform_data should be defined in a public header in
include/sound/ rather than in sound/soc/codecs folder.
In additional, the platform data support is not properly handled in this
driver so remove it now.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The first valid register index is 1 rather than 0, and the CS4349_CHIPID
is readonly. So set .writeable_reg to avoid writing to these registers.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mode Control - Register 02h
Digital Interface Format (DIF[2:0]) Bits 6-4
DIF2 DIF1 DIF0 Description
0 0 0 Left-Justified, up to 24-bit data
0 0 1 I²S, up to 24-bit data
0 1 0 Right-Justified, 16-bit data
0 1 1 Right-Justified, 24-bit data
1 0 0 TDM slot 0
1 0 1 TDM slot 1
1 1 0 TDM slot 2
1 1 1 TDM slot 3
The DIF_MASK is 0x70, so current code does not correctly set the DIFx
setting. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rtd->codec does not necessarily point to the CODEC instance for which the
callback was called (e.g. for CODEC<->CODEC or multi-CODEC links). Use
dai->codec instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
dev_get_drvdata() will not return the snd_soc_runtime to which this CODEC
is attached, so the current code will result in undefined behavior.
To fix this just use regmap_update_bits(cs4349->regmap, ...) directly
instead of snd_soc_update_bits(rtd->codec, ...).
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver is used for rockchip board using a rt5645/rt5650.
Reviewed-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: zhengxing <zhengxing@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver is used for rockchip board using a max98090.
Reviewed-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: zhengxing <zhengxing@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
"ASoC: rt5645: Check if codec is initialized in workqueue handler"
adds a check if codec is NULL in rt5645_irq_detection, which
returns an int. However, "ASoC: rt5645: Remove irq_jack_detection
function" removes that function, and moves the code in
jack_detect_work, which returns void.
Remove the return value to fix compilation warning.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The max_register should be the maximum valid register index rather than
number of registers. Also remove unused defines.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Tim Howe <tim.howe@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to allow us to start adding extra annotations for sequences
without bloating register default tables duplicate the structure under
the new name reg_sequence and update the APIs to use that instead of
reg_default.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEbBAABAgAGBQJVqUFGAAoJECTWi3JdVIfQ3YUH+LWLxVerlyUj/uug4vhRLlp2
KkKLInX1r9Al8cRWo6ln3kdB8jTmOxFxm1XUkpz+IQLiF0yV5kGtVm7uBup/X4DA
5oi7313rPs4maS/jqwyuOUi8X+ZMkKxp1Pgf4dJAzRJPN5tlks3drYdqY2c7JdT0
q5IqUR1KIsouK1/wCBy17BEe9PLpjV6U/yN2E/b1tsW1utjtAgY5pPjv/MZpPJ8C
NI6WXHjdykIi6Peg1mHqczgGEkyRlKBllZVsOvFhX1yjy0ITvao5/Mpv8NK5BwwU
cOWPVLlXOwa4m+kVXePPgA4GlB2q1Xupw5k6TDPip5aCGUgS+ryKQmOVcNaJnA==
=C5/o
-----END PGP SIGNATURE-----
Merge tag 'regmap-seq-delay-api' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap into asoc-reg-default
regmap: Create a new struct reg_sequence for register sequences
In order to allow us to start adding extra annotations for sequences
without bloating register default tables duplicate the structure under
the new name reg_sequence and update the APIs to use that instead of
reg_default.
Conflicts:
sound/soc/codecs/da7210.c
sound/soc/codecs/rt5651.c
sound/soc/codecs/wm8993.c
This patch adds CTU (Channel Transfer Unit) support for rsnd driver.
But, it does nothing to data at this point, but is required for MIX
support.
CTU design is a little different from other IPs (CTU0 is including
CTU00 - CTU03, and CTU1 is including CTU10 - CTU13, these have different
register mapping) We need to care about it on this driver.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver is assuming Audio DMAC / Audio DMAC peri peri
are used from SSI/SSIU/SRC/DVC. But we will add CTU/MIX to this driver.
Then, current DMA path searching method is not understandable, and good
enough for this purpose. This patch update DMA path search method, more
simply.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver does not free irq when snd_soc_register_codec returns error.
It does not return error when request irq failed, either.
Add return when request irq failed, and free_irq if
snd_soc_register_codec failed.
Signed-off-by: Koro Chen <koro.chen@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
"ASoC: rt5645: Simplify rt5645_enable_push_button_irq" removes
the test that accessed rt5645->pdata.jd_mode (that test is now
done in rt5645_jack_detect only), so we do not need that
variable anymore.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dev_pm_ops variables are not modified after initialization in these
drivers, so make them const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes kernel panic on boot, if rt5645->codec is NULL when
rt5645_jack_detect_work is first called.
rt5645_jack_detect_work needs rt5645->codec to be initialized to setup
dapm pins. Also, reporting jack events is useless, as the jacks cannot
be set before the codec is ready.
Since we manually call the interrupt handler in
rt5645_set_jack_detect, the initial jack state will be reported
correctly, and dapm pins will be setup at that time.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is cleanup for CTU/MIX support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sometimes we would like to get each module directly, especially data path
searching. this patch adds rsnd_io_to_mod() macro, and existing
rsnd_io_to_mod_xxx() use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver is using Audio DMAC (via DMAEngine) and
Audio DMAC peri peri (via original method), and usage of these DMAC
are different. Indicates its naming is useful for debugging.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DVC doesn't support Gen1, check it beginning of probe
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_dma_ops is used only from dma.c, rsnd.h doesn't need it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It can help for connection debug
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
