It replaces dc3co_enabled with dc3co_exitline on intel_psr struct. And
it saves dc3co_exitline, not dc3co_enabled, so we can use dc3co_exitline
without intel_crtc_state on other psr internal function like as
intel_psr_enable_source().
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210519000625.3184321-12-lucas.demarchi@intel.com
Today when the DSI controller is paired with the Combo-PHY it
uses the high-speed (HS) Word clock for its low power (LP)
transmit PPI communication to the DPHY. The interface signaling
only changes state at an Escape clock frequency (i.e. its
effectively running on a virtual Tx Escape clock that is controlled
by counters w/in the controller), but all the interface flops are
running off the HS clock.
This has the following drawbacks:
* It is a deviation from the PPI spec which assumes signaling is
running on a physical Escape clock
* The PV timings are over constrained (HS timed to 312.5MHz vs.
an Escape clock of 20MHz max)
This feature is proposing to change the LP Tx communication between
the controller and the DPHY from a virtual Tx Escape clock to a physical
clock.
To do this we need to program two "M" divisors. One for the usual
DSI_ESC_CLK_DIV and DPHY_ESC_CLK_DIV register and one for MIPIO_DWORD8.
For DSI_ESC_CLK_DIV and DPHY_ESC_CLK_DIV registers the "M" is calculated
as following
Nt = ceil(f_link/160) (theoretical word clock)
Nact = max[3, Nt + (Nt + 1)%2] (actual word clock)
M = Nact * 8
For MIPIO_DWORD8 register, the divisor "M" is calculated as following
M = (Nact - 1)/2
BSpec: 55171
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210519000625.3184321-11-lucas.demarchi@intel.com
Update MBUS_CTL register if the 2 mbus can be joined as per the current
DDB allocation and active pipes, also update hashing mode and pipe
select bits as per the sequence mentioned in the bspec.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210519000625.3184321-10-lucas.demarchi@intel.com
Alderlake-P don't have programing sequences for MBUS or DBUF during
display initializaiton, instead it requires programing to those
registers during modeset because it to depend on the pipes left
enabled.
Bspec: 49213
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210519000625.3184321-7-lucas.demarchi@intel.com
ADL-P have basically the same TC connection and disconnection
sequences as ICL and TGL, the major difference is the new registers.
So here adding functions without the icl prefix in the name and
making the new functions call the platform specific function to access
the correct register.
v2:
- Retain DDI TC PHY ownership flag during modesetting.
BSpec: 55480
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210519000625.3184321-6-lucas.demarchi@intel.com
The SoC has 6 DDI ports(DDI A,DDI B and DDI TC1-4.
The first two are connected to combo phys while
the rest are connected to TC phys.
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Clinton Taylor <clinton.a.taylor@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Swathi Dhanavanthri <swathi.dhanavanthri@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210519000625.3184321-5-lucas.demarchi@intel.com
XE_LPD reduces the number of regular watermark latency levels from 8
to 6 on non-dgfx platforms. However the hardware also adds a special
purpose SAGV wateramrk (and an accompanying transition watermark) that
will be used by the hardware in place of the level 0 values during SAGV
transitions.
Bspec: 49325, 49326, 50419
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210519000625.3184321-4-lucas.demarchi@intel.com
Add the qp table for 444 formats, for 8bpc, 10bpc and 12bpc, as given by
the VESA C model for DSC 1.1
v2:
- Add include guard to header (Jani)
- Move the big tables to a .c file (Chris, Jani, Lucas)
v3:
- Make tables 'static const' and add lookup functions to index into
them. (Jani)
v3.1:
- Include missing .h file.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210519000625.3184321-3-lucas.demarchi@intel.com
Add methods to calculate rc parameters for all bpps, against the fixed
arrays that we already have for 8,10,12 valid o/p bpps, to cover RGB 444
formats. Our hw doesn't support YUV compression yet. The calculations
used here are from VESA C model for DSC 1.1
v2:
- Checkpatch fixes
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Juha-Pekka Heikkil <juha-pekka.heikkila@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Mohammed Khajapasha <mohammed.khajapasha@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210519000625.3184321-2-lucas.demarchi@intel.com
Finally, rename the header and source file from csr to dmc.
v2: Add file rename in Documentation.
- Place headers in orders. (Jani)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210518213444.11420-6-anusha.srivatsa@intel.com
UAPI Changes:
* drm: Disable connector force-probing for non-master clients
* drm: Enforce consistency between IN_FORMATS property and cap + related
driver cleanups
* drm/amdgpu: Track devices, process info and fence info via
/proc/<pid>/fdinfo
* drm/ioctl: Mark AGP-related ioctls as legacy
* drm/ttm: Provide tt_shrink file to trigger shrinker via debugfs;
Cross-subsystem Changes:
* fbdev/efifb: Special handling of non-PCI devices
* fbdev/imxfb: Fix error message
Core Changes:
* drm: Add connector helper to attach HDR-metadata property and convert
drivers
* drm: Add connector helper to compare HDR-metadata and convert drivers
* drm: Add conenctor helper to attach colorspace property
* drm: Signal colorimetry in HDMI infoframe
* drm: Support pitch for destination buffers; Add blitter function
with generic format conversion
* drm: Remove struct drm_device.pdev and update legacy drivers
* drm: Remove obsolete DRM_KMS_FB_HELPER config option in core and drivers
* drm: Remove obsolete drm_pci_alloc/drm_pci_free
* drm/aperture: Add helpers for aperture ownership and convert drivers, replaces rsp fbdev helpers
* drm/agp: Mark DRM AGP code as legacy and convert legacy drivers
* drm/atomic-helpers: Cleanups
* drm/dp: Handle downstream port counts of 0 correctly; AUX channel fixes; Use
drm_err_*/drm_dbg_*(); Cleanups
* drm/dp_dual_mode: Use drm_err_*/drm_dbg_*()
* drm/dp_mst: Use drm_err_*/drm_dbg_*(); Use Extended Base Receiver Capability DPCD space
* drm/gem-ttm-helper: Provide helper for dumb_map_offset and convert drivers
* drm/panel: Use sysfs_emit; panel-simple: Use runtime PM, Power up panel
when reading EDID, Cache EDID, Cleanups;
Lms397KF04: DT bindings
* drm/pci: Mark AGP helpers as legacy
* drm/print: Handle NULL for DRM devices gracefully
* drm/scheduler: Change scheduled fence track
* drm/ttm: Don't count SG BOs against pages_limit; Warn about freeing pinned
BOs; Fix error handling if no BO can be swapped out; Move special
handling of non-GEM drivers into vmwgfx; Move page_alignment into
the BO; Set drm-misc as TTM tree in MAINTAINERS; Cleanup
ttm_agp_backend; Add ttm_sys_manager for system domain; Cleanups
Driver Changes:
* drm: Don't set allow_fb_modifiers explictly in drivers
* drm/amdgpu: Pin/unpin fixes wrt to TTM; Use bo->base.size instead of
mem->num_pages
* drm/ast: Use managed pcim_iomap(); Fix EDID retrieval with DP501
* drm/bridge: MHDP8546: HDCP support + DT bindings, Register DP AUX channel
with userspace; Sil8620: Fix module dependencies; dw-hdmi: Add option to
not load CEC driver; Fix stopping in drm_bridge_chain_pre_enable();
Ti-sn65dsi86: Fix refclk handling, Break GPIO and MIPI-to-eDP into
subdrivers, Use pm_runtime autosuspend, cleanups; It66121: Add
driver + DT bindings; Adv7511: Support I2S IEC958 encoding; Anx7625: fix
power-on delay; Nwi-dsi: Modesetting fixes; Cleanups
* drm/bochs: Support screen blanking
* drm/gma500: Cleanups
* drm/gud: Cleanups
* drm/i915: Use correct max source link rate for MST
* drm/kmb: Cleanups
* drm/meson: Disable dw-hdmi CEC driver
* drm/nouveau: Pin/unpin fixes wrt to TTM; Use bo->base.size instead of
mem->num_pages; Register AUX adapters after their connectors
* drm/qxl: Fix shadow BO unpin
* drm/radeon: Duplicate some DRM AGP code to uncouple from legacy drivers
* drm/simpledrm: Add a generic DRM driver for simple-framebuffer devices
* drm/tiny: Fix log spam if probe function gets deferred
* drm/vc4: Add support for HDR-metadata property; Cleanups
* drm/virtio: Create dumb BOs as guest blobs;
* drm/vkms: Use managed drmm_universal_plane_alloc(); Add XRGB plane
composition; Add overlay support
* drm/vmwgfx: Enable console with DRM_FBDEV_EMULATION; Fix CPU updates
of coherent multisample surfaces; Remove reservation semaphore; Add
initial SVGA3 support; Support amd64; Use 1-based IDR; Use min_t();
Cleanups
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEchf7rIzpz2NEoWjlaA3BHVMLeiMFAmCb4QsACgkQaA3BHVML
eiPwUgf/eTodvGQyB0cjv1vyHlttLo2t9k4QBO0pzVH0DJokl/pMpY0CuS8A/afW
RmKLYod3TQb2QeEqWjocPxcYrh5WCbjdDZlmSb+pF+qau4b4s09SzIogK3lO1Nve
9N1WVa7C3JC3k3XYexpeZ78RtoNN0UboMKDfbZODnn1PtjVtOp7Nbb92trRuB7y+
B72A8RQMYB5IywVln9+lzLYcrmpHZbk/sLmC5pIGBPcTyhn0TFinUYlg9iq1PvNM
fIqvPvXwxDVRO6hgnxZWKrdvQKCOcl5KFnk4E6H+ZkgWJ+yuAWI9r2N9TeelcW+M
jlCHreWEHhuTPkr/ypnVmO8kuEgSFA==
=G9ip
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2021-05-12' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.14:
UAPI Changes:
* drm: Disable connector force-probing for non-master clients
* drm: Enforce consistency between IN_FORMATS property and cap + related
driver cleanups
* drm/amdgpu: Track devices, process info and fence info via
/proc/<pid>/fdinfo
* drm/ioctl: Mark AGP-related ioctls as legacy
* drm/ttm: Provide tt_shrink file to trigger shrinker via debugfs;
Cross-subsystem Changes:
* fbdev/efifb: Special handling of non-PCI devices
* fbdev/imxfb: Fix error message
Core Changes:
* drm: Add connector helper to attach HDR-metadata property and convert
drivers
* drm: Add connector helper to compare HDR-metadata and convert drivers
* drm: Add conenctor helper to attach colorspace property
* drm: Signal colorimetry in HDMI infoframe
* drm: Support pitch for destination buffers; Add blitter function
with generic format conversion
* drm: Remove struct drm_device.pdev and update legacy drivers
* drm: Remove obsolete DRM_KMS_FB_HELPER config option in core and drivers
* drm: Remove obsolete drm_pci_alloc/drm_pci_free
* drm/aperture: Add helpers for aperture ownership and convert drivers, replaces rsp fbdev helpers
* drm/agp: Mark DRM AGP code as legacy and convert legacy drivers
* drm/atomic-helpers: Cleanups
* drm/dp: Handle downstream port counts of 0 correctly; AUX channel fixes; Use
drm_err_*/drm_dbg_*(); Cleanups
* drm/dp_dual_mode: Use drm_err_*/drm_dbg_*()
* drm/dp_mst: Use drm_err_*/drm_dbg_*(); Use Extended Base Receiver Capability DPCD space
* drm/gem-ttm-helper: Provide helper for dumb_map_offset and convert drivers
* drm/panel: Use sysfs_emit; panel-simple: Use runtime PM, Power up panel
when reading EDID, Cache EDID, Cleanups;
Lms397KF04: DT bindings
* drm/pci: Mark AGP helpers as legacy
* drm/print: Handle NULL for DRM devices gracefully
* drm/scheduler: Change scheduled fence track
* drm/ttm: Don't count SG BOs against pages_limit; Warn about freeing pinned
BOs; Fix error handling if no BO can be swapped out; Move special
handling of non-GEM drivers into vmwgfx; Move page_alignment into
the BO; Set drm-misc as TTM tree in MAINTAINERS; Cleanup
ttm_agp_backend; Add ttm_sys_manager for system domain; Cleanups
Driver Changes:
* drm: Don't set allow_fb_modifiers explictly in drivers
* drm/amdgpu: Pin/unpin fixes wrt to TTM; Use bo->base.size instead of
mem->num_pages
* drm/ast: Use managed pcim_iomap(); Fix EDID retrieval with DP501
* drm/bridge: MHDP8546: HDCP support + DT bindings, Register DP AUX channel
with userspace; Sil8620: Fix module dependencies; dw-hdmi: Add option to
not load CEC driver; Fix stopping in drm_bridge_chain_pre_enable();
Ti-sn65dsi86: Fix refclk handling, Break GPIO and MIPI-to-eDP into
subdrivers, Use pm_runtime autosuspend, cleanups; It66121: Add
driver + DT bindings; Adv7511: Support I2S IEC958 encoding; Anx7625: fix
power-on delay; Nwi-dsi: Modesetting fixes; Cleanups
* drm/bochs: Support screen blanking
* drm/gma500: Cleanups
* drm/gud: Cleanups
* drm/i915: Use correct max source link rate for MST
* drm/kmb: Cleanups
* drm/meson: Disable dw-hdmi CEC driver
* drm/nouveau: Pin/unpin fixes wrt to TTM; Use bo->base.size instead of
mem->num_pages; Register AUX adapters after their connectors
* drm/qxl: Fix shadow BO unpin
* drm/radeon: Duplicate some DRM AGP code to uncouple from legacy drivers
* drm/simpledrm: Add a generic DRM driver for simple-framebuffer devices
* drm/tiny: Fix log spam if probe function gets deferred
* drm/vc4: Add support for HDR-metadata property; Cleanups
* drm/virtio: Create dumb BOs as guest blobs;
* drm/vkms: Use managed drmm_universal_plane_alloc(); Add XRGB plane
composition; Add overlay support
* drm/vmwgfx: Enable console with DRM_FBDEV_EMULATION; Fix CPU updates
of coherent multisample surfaces; Remove reservation semaphore; Add
initial SVGA3 support; Support amd64; Use 1-based IDR; Use min_t();
Cleanups
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/YJvkD523evviED01@linux-uq9g.fritz.box
Buffer compression is not usable in A stepping.
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Clinton A Taylor <clinton.a.taylor@intel.com>
Cc: Juha-Pekka Heikkilä <juha-pekka.heikkila@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210514153711.2359617-20-matthew.d.roper@intel.com
Implementation details are in the HSD 22011320316, requiring CD clock
to be at least 307MHz to make DC states to work.
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210514153711.2359617-19-matthew.d.roper@intel.com
Respective bit for master or slave to be set for uncompressed
bigjoiner in dss_ctl1 register.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210514153711.2359617-16-matthew.d.roper@intel.com
For uncompressed big joiner DSC engine will not be used so will avoid
compute config of DSC.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210514153711.2359617-15-matthew.d.roper@intel.com
No need for checking dsc flag for uncompressed pipe joiner mode
validation.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210514153711.2359617-14-matthew.d.roper@intel.com
Disable loadgen sharing for DP link rate 1.62 GHz and HDMI 5.94 GHz.
For all other modes, we can enable loadgen sharing feature.
BSpec: 55359
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210514153711.2359617-13-matthew.d.roper@intel.com
Move intel_modeset_all_pipes() to a central place so that we can
use it elsewhere as well. No functional changes.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210514153711.2359617-12-matthew.d.roper@intel.com
Alderlake P have modular FIA like TGL but it is always modular in all
skus, not like TGL that we had to read a register to check if it is
monolithic or modular.
BSpec: 55480
BSpec: 50572
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210514153711.2359617-11-matthew.d.roper@intel.com
When DP_PHY_MODE_STATUS_NOT_SAFE is set, it means that display
has the control over the TC phy.
The "not safe" naming is confusing using ownership make it easier
to read also future platforms will have a new register that does the
same job as DP_PHY_MODE_STATUS_NOT_SAFE but with the onwership name.
BSpec: 49294
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210514153711.2359617-10-matthew.d.roper@intel.com
ADL-P has 3 possible refclk frequencies: 19.2MHz,
24MHz and 38.4MHz
While we're at it, remove the drm_WARNs. They've never actually helped
us catch any problems, but it's very easy to forget to update them
properly for new platforms.
BSpec: 55409, 49208
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Clinton Taylor <clinton.a.taylor@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210514153711.2359617-9-matthew.d.roper@intel.com
Support compression BPPs from bpc to uncompressed BPP -1.
So far we have 8,10,12 as valid compressed BPPS now the
support is extended.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210514153711.2359617-5-matthew.d.roper@intel.com
Move the platform specific max bpc calculation into
intel_dp_dsc_compute_bpp function
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210514153711.2359617-4-matthew.d.roper@intel.com
The DDI naming template for display version 12 went A-C, TC1-TC6. With
XE_LPD, that naming scheme for DDI's has now changed to A-E, TC1-TC4.
The XE_LPD design keeps the register offsets and bitfields relating to
the TC outputs in the same location they were previously. The new "D"
and "E" outputs now take the locations that were previously used by TC5
and TC6 outputs, or what we would have considered to be outputs "H" and
"I" under the legacy lettering scheme.
For the most part everything will just work as long as we initialize the
output with the proper 'enum port' value. However we do need to take
care to pick the correct AUX channel when parsing the VBT (e.g., a
reference to 'AUX D' is actually asking us to use the 8th aux channel,
not the fourth). We should also make sure that our encoders and aux
channels are named appropriately so that it's easier to correlate driver
debug messages with the bspec instructions.
v2:
- Update handling of TGL_TRANS_CLK_SEL_PORT. (Jose)
v3:
- Add hpd_pin to handle outputs D and E (Jose)
- Fixed conversion of BIOS port to aux ch for TC ports (Jose)
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210514153711.2359617-2-matthew.d.roper@intel.com
Add ADP-P PCH device ID and assign as ADL PCH if found. Previously we
would assign the DDC pin map based on the PCH, but it can also change
based on the CPU. From Bspec 20124: "The physical port to pin pair
mapping are defined in the Bspec per PCH. Mapping can further change
based on CPU Si used as CPU and PCH can be mixed and matched".
Bspec: 20124
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210512042144.2089071-7-matthew.d.roper@intel.com
If VT-d is active, the memory bandwidth usage of the display is 5%
higher. Take this into account when determining whether we can support
a display configuration.
Bspec: 64631
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210512042144.2089071-5-matthew.d.roper@intel.com
Aside from the hardware-managed PG0, XE_LPD has power wells 1-2 and
A-D. These power wells should be enabled/disabled according to the
following dependency tree (enable top to bottom, disable bottom to top):
PG0
|
--PG1--
/ \
PGA --PG2--
/ | \
PGB PGC PGD
PWR_WELL_CTL follows the general ICL/TGL design and places PG A-D in the
bits that would have been PG 6-9 under the old scheme.
PWR_WELL_CTL_{DDI,AUX}'s bit indexing for DDI's A-C and TC1 is the same
as TGL, but DDI-D is placed at index 7 (bits 14 & 15).
v2:
- Squash in LPSP status patch from Uma since it's also a
powerwell-specific change.
Bspec: 49233
Bspec: 49503
Bspec: 49504
Bspec: 49505
Bspec: 49296
Bspec: 50090
Bspec: 53920
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210512042144.2089071-4-matthew.d.roper@intel.com
XE_LPD's plane support is identical to RKL and ADL-S --- 5 universal + 1
cursor with NV12 UV support on planes 1-3 and NV12 Y support on planes
4-5.
v2:
- Drop the extra 90/270 rotation check in skl_plane_check_fb(); the DRM
property code will already prevent userspace from passing us values
that weren't advertised. (Lucas)
Bspec: 53657
Bspec: 49251
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210512042144.2089071-3-matthew.d.roper@intel.com
Fix the typo in DPCD caps used for checking SRC CTL mode of
HDMI2.1 PCON
v2: Corrected Fixes tag (Jani Nikula).
v3: Rebased.
Fixes: 04b6603d13 ("drm/i915/display: Configure HDMI2.1 Pcon for FRL only if Src-Ctl mode is available")
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: "Ville Syrj_l_" <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Swati Sharma <swati2.sharma@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210511120930.12218-1-ankit.k.nautiyal@intel.com
(cherry picked from commit 88a9c5485c)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
__i915_active_call annotation is required on the retire callback to ensure
correct function alignment.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: a21ce8ad12 ("drm/i915/overlay: Switch to using i915_active tracking")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210429083530.849546-1-tvrtko.ursulin@linux.intel.com
(cherry picked from commit d8e44e4dd2)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Fix the typo in DPCD caps used for checking SRC CTL mode of
HDMI2.1 PCON
v2: Corrected Fixes tag (Jani Nikula).
v3: Rebased.
Fixes: 04b6603d13 ("drm/i915/display: Configure HDMI2.1 Pcon for FRL only if Src-Ctl mode is available")
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: "Ville Syrj_l_" <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Swati Sharma <swati2.sharma@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210511120930.12218-1-ankit.k.nautiyal@intel.com
This workaround requires that VIDEO_DIP_ENABLE_VSC_HSW is never set
with PSR.
BSpec: 54369
BSpec: 54077
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210418002126.87882-5-jose.souza@intel.com
All of this places don't need to intel_psr_enabled() that will lock
psr mutex, check state and unlock.
Instead it can directly check PSR state in intel_crtc_state, the only
place that was not possible was intel_read_dp_vsc_sdp() but since
"drm/i915/display: Fill PSR state during hardware configuration read
out" it is possible.
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210418002126.87882-2-jose.souza@intel.com
So far if we had a mismatch between the state asked and what was
programmed in hardware for PSR, this mismatch would go unnoticed.
So here adding the PSR to the hardware configuration readout,
EDP_PSR_CTL and EDP_PSR2_CTL can't be directly read because its state
flips due to other factors like frontbuffer modifications and CRC.
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210418002126.87882-1-jose.souza@intel.com
When encoder validation of a display mode fails, retry with less bandwidth
heavy YCbCr420 color mode, if available. This enables some HDMI 1.4 setups
to support 4k60Hz output, which previously failed silently.
AMDGPU had nearly the exact same issue. This problem description is
therefore copied from my commit message of the AMDGPU patch.
On some setups, while the monitor and the gpu support display modes with
pixel clocks of up to 600MHz, the link encoder might not. This prevents
YCbCr444 and RGB encoding for 4k60Hz, but YCbCr420 encoding might still be
possible. However, which color mode is used is decided before the link
encoder capabilities are checked. This patch fixes the problem by retrying
to find a display mode with YCbCr420 enforced and using it, if it is
valid.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210510133349.14491-4-wse@tuxedocomputers.com
Couples the decission between RGB and YCbCr420 mode and the check if the
port clock can archive the required frequency. Other checks and
configuration steps that where previously done in between can also be done
before or after.
This allows for are cleaner implementation of retrying different color
encodings.
A slight change in behaviour occurs with this patch: If YCbCr420 is not
allowed but display is YCbCr420 only it no longer fails, but just prints
an error and tries to fallback on RGB.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210510133349.14491-3-wse@tuxedocomputers.com
Screen flickers on Innolux eDP 1.3 panel when clock rate 540000 is in use.
According to the panel vendor, though clock rate 540000 is advertised,
but the max clock rate it really supports is 270000.
Ville Syrjälä mentioned that fast and narrow also breaks some eDP 1.4
panel, so use slow and wide training for all panels to resolve the
issue.
User also confirmed that the new strategy doesn't introduce any
regression on XPS 9380.
v2:
- Use slow and wide for everything.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/3384
References: https://gitlab.freedesktop.org/drm/intel/-/issues/272
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210421052054.1434718-1-kai.heng.feng@canonical.com
(cherry picked from commit acca7762eb)
Fixes: 2bbd6dba84 ("drm/i915: Try to use fast+narrow link on eDP again and fall back to the old max strategy on failure")
Cc: <stable@vger.kernel.org> # v5.12+
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Direction on gen9+ was to stop reading the straps and only rely on the
VBT for marking the port presence. This happened while dealing with
WaIgnoreDDIAStrap and instead of using it as a WA, it should now be the
normal flow. See commit 885d3e5b6f ("drm/i915/display: fix comment on
skl straps").
For gen 10 it's hard to say if this will work or not since I can't test
it, so leave it with the same behavior as before.
For PCH_TGP we should still rely on the VBT to make ports E and F not
available.
v2 (Ville):
- use display ver >= 9 to make it consistent with the rest of the
driver instead of checking for == 9
- also handle CNL and only initialize port F if it is
IS_CNL_WITH_PORT_F. Eventually CNL may be removed, but while it
isn't let's keep it consistent everywhere
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210430223808.1078010-4-lucas.demarchi@intel.com
Since commit 45c0673aac ("drm/i915/bios: start using the
intel_bios_encoder_data directly") we lookup the devdata for each port
in intel_ddi_init() and just return if the port is not present in VBT
(or if we didn't create a fake devdata for it if VBT is not available).
So in intel_display.c we don't have to check
intel_bios_is_port_present(), just rely on the check in
intel_ddi_init().
v2: Rebase on commit 45c0673aac ("drm/i915/bios: start using the
intel_bios_encoder_data directly") re-using that check in intel_ddi_init()
instead of adding a new one.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210430223808.1078010-2-lucas.demarchi@intel.com
intel_dp_check_mst_status() uses a 14-byte array to read the DPRX Event
Status Indicator data, but then passes that buffer at offset 10 off as
an argument to drm_dp_channel_eq_ok().
End result: there are only 4 bytes remaining of the buffer, yet
drm_dp_channel_eq_ok() wants a 6-byte buffer. gcc-11 correctly warns
about this case:
drivers/gpu/drm/i915/display/intel_dp.c: In function ‘intel_dp_check_mst_status’:
drivers/gpu/drm/i915/display/intel_dp.c:3491:22: warning: ‘drm_dp_channel_eq_ok’ reading 6 bytes from a region of size 4 [-Wstringop-overread]
3491 | !drm_dp_channel_eq_ok(&esi[10], intel_dp->lane_count)) {
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/i915/display/intel_dp.c:3491:22: note: referencing argument 1 of type ‘const u8 *’ {aka ‘const unsigned char *’}
In file included from drivers/gpu/drm/i915/display/intel_dp.c:38:
include/drm/drm_dp_helper.h:1466:6: note: in a call to function ‘drm_dp_channel_eq_ok’
1466 | bool drm_dp_channel_eq_ok(const u8 link_status[DP_LINK_STATUS_SIZE],
| ^~~~~~~~~~~~~~~~~~~~
6:14 elapsed
This commit just extends the original array by 2 zero-initialized bytes,
avoiding the warning.
There may be some underlying bug in here that caused this confusion, but
this is at least no worse than the existing situation that could use
random data off the stack.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The intel driver uses the same logic to attach the Colorspace property
in multiple places and we'll need it in vc4 too. Let's move that common
code in a helper.
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210430094451.2145002-4-maxime@cerno.tech
All the drivers that support the HDR metadata property have a similar
function to compare the metadata from one connector state to the next,
and force a mode change if they differ.
All these functions run pretty much the same code, so let's turn it into
an helper that can be shared across those drivers.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210430094451.2145002-2-maxime@cerno.tech
All the drivers that implement HDR output call pretty much the same
function to initialise the hdr_output_metadata property, and while the
creation of that property is in a helper, every driver uses the same
code to attach it.
Provide a helper for it as well
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210430094451.2145002-1-maxime@cerno.tech
The specification only requires DPT FB strides to be POT aligned, but
there seems to be also a minimum of 8 stride tile requirement. Scanning
out FBs with < 8 stride tiles will result in pipe faults (even though
the stride is POT aligned).
Signed-off-by: Imre Deak <imre.deak@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210506161930.309688-10-imre.deak@intel.com
The latest specification removed the support for 90/270 FB rotation on
ADL_P, even though legacy Y-tiled surfaces are supported. Align the code
accordingly.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210506161930.309688-9-imre.deak@intel.com
Alderlake-P have a new stride restriction when using DPT and it is used
by non linear framebuffers. Stride needs to be a power of two to take
full DPT rows, but stride is a parameter set by userspace.
What we could do is use a fake stride when doing DPT allocation so
HW requirements are met and userspace don't need to be changed to
met this power of two restrictions but this change will take a while
to be implemented so for now adding this restriction in driver to
reject atomic commits that would cause visual corruptions.
BSpec: 53393
Acked-by: Matt Roper <matthew.d.roper@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210506161930.309688-8-imre.deak@intel.com
XE_LPD supports plane strides up to 128KB.
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Juha-Pekka Heikkilä <juha-pekka.heikkila@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210506161930.309688-7-imre.deak@intel.com
GTT remapping allow us to have planes with strides larger than HW
supports but DPT + GTT remapping is still not properly handled so
falling back to plane HW limitations for now.
This patch can be dropped when DPT + GTT remapping is correctly
handled but until then we need this limitation for all display13
platforms to avoid pipe faults.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Clint Taylor <Clinton.A.Taylor@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210506161930.309688-6-imre.deak@intel.com
Add support for DPT (display page table). DPT is a
slightly peculiar two level page table scheme used for
tiled scanout buffers (linear uses direct ggtt mapping
still). The plane surface address will point at a page
in the DPT which holds the PTEs for 512 actual pages.
Thus we require 1/512 of the ggttt address space
compared to a direct ggtt mapping.
We create a new DPT address space for each framebuffer and
track two vmas (one for the DPT, another for the ggtt).
TODO:
- Is the i915_address_space approaach sane?
- Maybe don't map the whole DPT to write the PTEs?
- Deal with remapping/rotation? Need to create a
separate DPT for each remapped/rotated plane I
guess. Or else we'd need to make the per-fb DPT
large enough to support potentially several
remapped/rotated vmas. How large should that be?
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Bommu Krishnaiah <krishnaiah.bommu@intel.com>
Cc: Wilson Chris P <Chris.P.Wilson@intel.com>
Cc: Tang CQ <cq.tang@intel.com>
Cc: Auld Matthew <matthew.auld@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Wilson Chris P <Chris.P.Wilson@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210506161930.309688-5-imre.deak@intel.com
Let's start preparing for upcoming platforms that will use an XE_LPD
design.
v2:
- Use the now-preferred "XE_LPD" term to refer to this design
- Utilize DISPLAY_VER() rather than a feature flag
- Drop unused mbus_size field (Lucas)
v3:
- Adjust for dbuf.{size,slice_mask} (Ville)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com> (v2)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210506161930.309688-2-imre.deak@intel.com
When scanning out NV12 if we at any time have the plane enabled
while the scaler is disabled we get a pretty catastrophic
underrun.
Let's reorder the operations so that we try to avoid that happening
even if our vblank evade fails and the scaler enable/disable and
the plane enable/disable get latched during two diffent frames.
This takes care of the most common cases. I suppose there is still
at least a theoretical possibility of hitting this if one plane
takes the scaler away from another plane before the second plane
had a chance to set up another scaler for its use. But that
is starting to get a bit complicated, especially since the plane
commit order already has to be carefully sequenced to avoid any
dbuf overlaps. So plugging this 100% may prove somewhat hard...
Cc: Cooper Chiou <cooper.chiou@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210506073836.14848-1-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
I doubt anyone has used the display error state since CS flips
went the way of the dodo. Just nuke it.
It might be semi interesting to have something like this for
FIFO underruns and the like, but as it stands this wouldn't
provide a sufficient amount of information. So would need
an extensive rewrite anyway.
The lockless power well handling is also racy, so this could
just be contributing noise to test results if we end up
accessing something with the relevant power well already
disabled.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210505191140.14215-1-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
The implementation of two workarounds are missing causing failures
in CI with pre-production HW.
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210505213801.80772-1-jose.souza@intel.com
Since
commit 890880ddfd
Author: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Date: Fri Jan 4 09:56:10 2019 +0100
drm: Auto-set allow_fb_modifiers when given modifiers at plane init
this is done automatically as part of plane init, if drivers set the
modifier list correctly. Which is the case here.
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: "Ville Syrjälä" <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: "José Roberto de Souza" <jose.souza@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Karthik B S <karthik.b.s@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210427092018.832258-3-daniel.vetter@ffwll.ch
Replace the hand rolled rmw sequences with intel_de_rmw().
Jani pointed out that intel_de_rmw() skips the write if the
value does not change. That should be totally fine here, but
let's at least acknowledge the change in behaviour in case I'm
somehow wrong...
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210430153444.29270-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
We lost the i915_reg_rw tracepoint for a lot of display registers
when we switched from the heavyweight normal register accessors to
the lightweight _fw() variants. See eg. commit dd584fc071
("drm/i915: Use I915_READ_FW for plane updates").
Put the tracepoints back so that the register traces might
actually be useful. Hopefully these should be close to free
when the tracepoint is not enabled and thus not slow down
our vblank critical sections significantly.
v2: Copy paste the same-cacheline-hang warning from
intel_uncore.h (Anshuman)
Cc: Cooper Chiou <cooper.chiou@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210430143945.6776-2-ville.syrjala@linux.intel.com
Hoist the intel_de.h include from intel_display_types.h one
level up. I need this in order to untangle the include order
so that I can add tracepoints into intel_de.h.
This little cocci script did most of the work for me:
@find@
@@
(
intel_de_read(...)
|
intel_de_read_fw(...)
|
intel_de_write(...)
|
intel_de_write_fw(...)
)
@has_include@
@@
(
#include "intel_de.h"
|
#include "display/intel_de.h"
)
@depends on find && !has_include@
@@
+ #include "intel_de.h"
#include "intel_display_types.h"
@depends on find && !has_include@
@@
+ #include "display/intel_de.h"
#include "display/intel_display_types.h"
Cc: Cooper Chiou <cooper.chiou@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210430143945.6776-1-ville.syrjala@linux.intel.com
Make sure that the XYUV8888 format is handled correctly when it's used
with a MC_CCS modifier framebuffer. Besides this format not working, the
driver will also return an incorrect error value when trying to use it,
indicating that the second color plane in the framebuffer is set
unexpectedly.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210501002853.4132009-1-imre.deak@intel.com
We use some of the lower bits of the retire function pointer for
potential flags, which is quite thorny, since the caller needs to
remember to give the function the correct alignment with
__i915_active_call, otherwise we might incorrectly unpack the pointer
and jump to some garbage address later. Instead of all this let's just
pass the flags along as a separate parameter.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
References: ca419f407b ("drm/i915: Fix crash in auto_retire")
References: d8e44e4dd2 ("drm/i915/overlay: Fix active retire callback alignment")
References: fd5f262db1 ("drm/i915/selftests: Fix active retire callback alignment")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210504164136.96456-1-matthew.auld@intel.com
Registering multiple backlight devices with intel_backlight name will
obviously fail, regardless of whether they're two connectors in the same
drm device or two different drm devices.
It would be preferrable to switch to completely unique names, and sunset
the generic intel_backlight name. However, there are apparently users
out there that hardcode the name, so the change would break backward
compatibility.
As a compromise, register the first device with intel_backlight name. In
the common case, this is the only backlight device anyway. From the
second device on, use card%d-%s-backlight format, for example
card0-eDP-2-backlight, to make the name unique.
This approach does not preclude us from registering the first device
using the same naming scheme in the future.
v2: Keep using intel_backlight name for first backlight device
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2794
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/7dc3f6974711ce44522189dc9db05d1e6e24e6d8.1619604743.git.jani.nikula@intel.com
Add connector and backlight device name to logging, and propagate error
code from backlight_device_register() instead of flattening to
-ENODEV. Storing the name in an allocated buffer is unnecessary here,
but makes follow-up work on names much cleaner.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/271206461d9c0f42755792236330b588df3b532e.1619604743.git.jani.nikula@intel.com
[why]
Previously used value was not safe to provide the correct value, i.e. it
could be 0 if not not configured, leading to no MST on this platform.
[how]
Do not use the value from BIOS, but from the structure populated at
encoder initialization time.
Fixes: 98025a62cb ("drm/dp_mst: Use Extended Base Receiver Capability DPCD space")
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[fixed open coded drm_dp_link_rate_to_bw_code()]
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210430214531.24565-2-nikola.cornij@amd.com
tegra:
- Tegra186 hardware cursor support
- better capability reporting for different SoC
- better framebuffer modifier support
- host1x fixes
ttm:
- fix unswappable BO handling
efifb:
- check for PCI before using it
amdgpu:
- Fixes for Aldebaran
- Display LTTPR fixes
- eDP fixes
- Fixes for Vangogh
- RAS fixes
- ASPM support
- Renoir SMU fixes
- Modifier fixes
- Misc code cleanups
- Freesync fixes
i915:
- Several fixes to GLK handling in recent display refactoring
- Rare watchdog timer race fix
- Cppcheck redundant condition fix
- Overlay error code propagation fix
- Documentation fix
- gvt: Remove one unused function warning
- gvt: Fix intel_gvt_init_device() return type
- gvt: Remove one duplicated register accessible check
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJgi1hjAAoJEAx081l5xIa+ydkP/1Etl4S07UiLkWtHNOl5lj33
RCCfjjeqTc5Md2qXuCknEsju38P493Pqhh1j7Nl02QHE1pIyTEjhKTdv/zt7aC0R
jVUw4ZvtkqN2U1azS8Wfa+YBqrkerrdGIvaIJa/s9eLN+r+/Vb7Crid5NJg5/RQL
NLN2Riw95MrvrsGFnZRli8qiLbIK2pj3553KZWJim4o9Fp+1TAesXVLI1+qXoIRk
WWLuhwLxPLSb+ONCbrcOFSAwxVZLwRM90B+jwnhRYLS/Zo1hcWhn9ua5RBdyC5zU
rGuOA6dWmI4o4L0X+IaNLD4qOGAWTp1dnJtvKj4rQVfSR82hWcTlCnVcZgxjjydx
m56TlBLGYvilClM5tmRUdW5QKW4c9DP7dAr3XiKyYOuL2pRkg904ziQs4fVwmOgV
PfDNm/aA+40UKPwLu0+JM7aQO5OgL8pg1FpOck5qOIx9fAQrulPp9OHDbxXVAzax
t6YmmBnlXShZSooEkwfoCILkdZuNwmj1sXwUh3QzeQj6owk4tg+LWJIqK9mHt+lQ
YuyueS+hOn1uSzhtLs9QdQvNssLVd490i0tyU/GGNMw/QVyi9gg4Iq2dVk00L9if
lFQ7PgPslT+ExIdVutsnuLsy9N2by0AcxFJLdYKELTTicTVhYKzArGeCxni/A35r
7ZmtSPvbuY7g1//n03Nb
=4Wh+
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2021-04-30' of git://anongit.freedesktop.org/drm/drm
Pull more drm updates from Dave Airlie:
"Looks like I missed a tegra feature request for next, but should still
be fine since it's pretty self contained.
Apart from that got a set of i915 and amdgpu fixes as per usual along
with a few misc fixes.
tegra:
- Tegra186 hardware cursor support
- better capability reporting for different SoC
- better framebuffer modifier support
- host1x fixes
ttm:
- fix unswappable BO handling
efifb:
- check for PCI before using it
amdgpu:
- Fixes for Aldebaran
- Display LTTPR fixes
- eDP fixes
- Fixes for Vangogh
- RAS fixes
- ASPM support
- Renoir SMU fixes
- Modifier fixes
- Misc code cleanups
- Freesync fixes
i915:
- Several fixes to GLK handling in recent display refactoring
- Rare watchdog timer race fix
- Cppcheck redundant condition fix
- Overlay error code propagation fix
- Documentation fix
- gvt: Remove one unused function warning
- gvt: Fix intel_gvt_init_device() return type
- gvt: Remove one duplicated register accessible check"
* tag 'drm-next-2021-04-30' of git://anongit.freedesktop.org/drm/drm: (111 commits)
efifb: Check efifb_pci_dev before using it
drm/i915: Fix docbook descriptions for i915_gem_shrinker
drm/i915: fix an error code in intel_overlay_do_put_image()
drm/i915/display/psr: Fix cppcheck warnings
drm/i915: Disable LTTPR detection on GLK once again
drm/i915: Restore lost glk ccs w/a
drm/i915: Restore lost glk FBC 16bpp w/a
drm/i915: Take request reference before arming the watchdog timer
drm/ttm: fix error handling if no BO can be swapped out v4
drm/i915/gvt: Remove duplicated register accessible check
drm/amdgpu/gmc9: remove dummy read workaround for newer chips
drm/amdgpu: Add mem sync flag for IB allocated by SA
drm/amdgpu: Fix SDMA RAS error reporting on Aldebaran
drm/amdgpu: Reset RAS error count and status regs
Revert "drm/amdgpu: workaround the TMR MC address issue (v2)"
drm/amd/display: 3.2.132
drm/amd/display: [FW Promotion] Release 0.0.62
drm/amd/display: add helper for enabling mst stream features
drm/amd/display: Report Proper Quantization Range in AVI Infoframe
drm/amd/display: Fix call to pass bpp in 16ths of a bit
...
__i915_active_call annotation is required on the retire callback to ensure
correct function alignment.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: a21ce8ad12 ("drm/i915/overlay: Switch to using i915_active tracking")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210429083530.849546-1-tvrtko.ursulin@linux.intel.com
[why]
DP 1.4a spec mandates that if DP_EXTENDED_RECEIVER_CAP_FIELD_PRESENT is
set, Extended Base Receiver Capability DPCD space must be used. Without
doing that, the three DPCD values that differ will be wrong, leading to
incorrect or limited functionality. MST link rate, for example, could
have a lower value. Also, Synaptics quirk wouldn't work out well when
Extended DPCD was not read, resulting in no DSC for such hubs.
[how]
Modify MST topology manager to use the values from Extended DPCD where
applicable.
To prevent regression on the sources that have a lower maximum link rate
capability than MAX_LINK_RATE from Extended DPCD, have the drivers
supply maximum lane count and rate at initialization time.
This also reverts commit 2dcab875e7 ("Revert drm/dp_mst: Retrieve
extended DPCD caps for topology manager"), brining the change back to the
original commit ad44c03208 ("drm/dp_mst: Retrieve extended DPCD caps for
topology manager").
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210429221151.22020-2-nikola.cornij@amd.com
- printk fourcc modifier support added %p4cc
core:
- drm_crtc_commit_wait
- atomic plane state helpers reworked for full state
- dma-buf heaps API rework
- edid: rework and improvements for displayid
dp-mst:
- better topology logging
bridge:
- Chipone ICN6211
- Lontium LT8912B
- anx7625 regulator support
panel:
- fix lt9611 4k panels handling
simple-kms:
- add plane state helpers
ttm:
- debugfs support
- removal of unused sysfs
- ignore signaled moved fences
- ioremap buffer according to mem caching
i915:
- Alderlake S enablement
- Conversion to dma_resv_locking
- Bring back watchdog timeout support
- legacy ioctl cleanups
- add GEM TDDO and RFC process
- DG1 LMEM preparation work
- intel_display.c refactoring
- Gen9/TGL PCH combination support
- eDP MSO Support
- multiple PSR instance support
- Link training debug updates
- Disable PSR2 support on JSL/EHL
- DDR5/LPDDR5 support for bw calcs
- LSPCON limited to gen9/10 platforms
- HSW/BDW async flip/VTd corruption workaround
= SAGV watermakr fixes
- SNB hard hang on ring resume fix
- Limit imported dma-buf size
- move to use new tasklet API
- refactor KBL/TGL/ADL-S display/gt steppings
- refactoring legacy DP/HDMI, FB plane code out
amdgpu:
- uapi: add ioctl to query video capabilities
- Iniital AMD Freesync HDMI support
- Initial Adebaran support
- 10bpc dithering improvements
- DCN secure display support
- Drop legacy IO BAR requirements
- PCIE/S0ix/RAS/Prime/Reset fixes
- Display ASSR support
- SMU gfx busy queues for RV/PCO
- Initial LTTPR display work
amdkfd:
- MMU notifier fixes
- APU fixes
radeon:
- debugfs cleanps
- fw error handling ifix
- Flexible array cleanups
msm:
- big DSI phy/pll cleanup
- sc7280 initial support
- commong bandwidth scaling path
- shrinker locking contention fixes
- unpin/swap support for GEM objcets
ast:
- cursor plane handling reworked
tegra:
- don't register DP AUX channels before connectors
zynqmp:
- fix OOB struct padding memset
gma500:
- drop ttm and medfield support
exynos:
- request_irq cleanup function
mediatek:
- fine tune line time for EOTp
- MT8192 dpi support
- atomic crtc config updates
- don't support HDMI connector creation
mxsdb:
- imx8mm support
panfrost:
-= MMU IRQ handling rework
qxl:
- locking fixes
- resource deallocation changes
sun4i:
- add alpha properties to UI/VI layers
vc4:
- RPi4 CEC support
vmwgfx:
- doc cleanups
arc:
- moved to drm/tiny
-----BEGIN PGP SIGNATURE-----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=bLWZ
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2021-04-28' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"The usual lots of work all over the place.
i915 has gotten some Alderlake work and prelim DG1 code, along with a
major locking rework over the GEM code, and brings back the property
of timing out long running jobs using a watchdog. amdgpu has some
Alderbran support (new GPU), freesync HDMI support along with a lot
other fixes.
Outside of the drm, there is a new printf specifier added which should
have all the correct acks/sobs:
- printk fourcc modifier support added %p4cc
Summary:
core:
- drm_crtc_commit_wait
- atomic plane state helpers reworked for full state
- dma-buf heaps API rework
- edid: rework and improvements for displayid
dp-mst:
- better topology logging
bridge:
- Chipone ICN6211
- Lontium LT8912B
- anx7625 regulator support
panel:
- fix lt9611 4k panels handling
simple-kms:
- add plane state helpers
ttm:
- debugfs support
- removal of unused sysfs
- ignore signaled moved fences
- ioremap buffer according to mem caching
i915:
- Alderlake S enablement
- Conversion to dma_resv_locking
- Bring back watchdog timeout support
- legacy ioctl cleanups
- add GEM TDDO and RFC process
- DG1 LMEM preparation work
- intel_display.c refactoring
- Gen9/TGL PCH combination support
- eDP MSO Support
- multiple PSR instance support
- Link training debug updates
- Disable PSR2 support on JSL/EHL
- DDR5/LPDDR5 support for bw calcs
- LSPCON limited to gen9/10 platforms
- HSW/BDW async flip/VTd corruption workaround
- SAGV watermark fixes
- SNB hard hang on ring resume fix
- Limit imported dma-buf size
- move to use new tasklet API
- refactor KBL/TGL/ADL-S display/gt steppings
- refactoring legacy DP/HDMI, FB plane code out
amdgpu:
- uapi: add ioctl to query video capabilities
- Iniital AMD Freesync HDMI support
- Initial Adebaran support
- 10bpc dithering improvements
- DCN secure display support
- Drop legacy IO BAR requirements
- PCIE/S0ix/RAS/Prime/Reset fixes
- Display ASSR support
- SMU gfx busy queues for RV/PCO
- Initial LTTPR display work
amdkfd:
- MMU notifier fixes
- APU fixes
radeon:
- debugfs cleanps
- fw error handling ifix
- Flexible array cleanups
msm:
- big DSI phy/pll cleanup
- sc7280 initial support
- commong bandwidth scaling path
- shrinker locking contention fixes
- unpin/swap support for GEM objcets
ast:
- cursor plane handling reworked
tegra:
- don't register DP AUX channels before connectors
zynqmp:
- fix OOB struct padding memset
gma500:
- drop ttm and medfield support
exynos:
- request_irq cleanup function
mediatek:
- fine tune line time for EOTp
- MT8192 dpi support
- atomic crtc config updates
- don't support HDMI connector creation
mxsdb:
- imx8mm support
panfrost:
- MMU IRQ handling rework
qxl:
- locking fixes
- resource deallocation changes
sun4i:
- add alpha properties to UI/VI layers
vc4:
- RPi4 CEC support
vmwgfx:
- doc cleanups
arc:
- moved to drm/tiny"
* tag 'drm-next-2021-04-28' of git://anongit.freedesktop.org/drm/drm: (1390 commits)
drm/ttm: Don't count pages in SG BOs against pages_limit
drm/ttm: fix return value check
drm/bridge: lt8912b: fix incorrect handling of of_* return values
drm: bridge: fix LONTIUM use of mipi_dsi_() functions
drm: bridge: fix ANX7625 use of mipi_dsi_() functions
drm/amdgpu: page retire over debugfs mechanism
drm/radeon: Fix a missing check bug in radeon_dp_mst_detect()
drm/amd/display: Fix the Wunused-function warning
drm/radeon/r600: Fix variables that are not used after assignment
drm/amdgpu/smu7: fix CAC setting on TOPAZ
drm/amd/display: Update DCN302 SR Exit Latency
drm/amdgpu: enable ras eeprom on aldebaran
drm/amdgpu: RAS harvest on driver load
drm/amdgpu: add ras aldebaran ras eeprom driver
drm/amd/pm: increase time out value when sending msg to SMU
drm/amdgpu: add DMUB outbox event IRQ source define/complete/debug flag
drm/amd/pm: add the callback to get vbios bootup values for vangogh
drm/radeon: Fix size overflow
drm/amdgpu: Fix size overflow
drm/amdgpu: move mmhub ras_func init to ip specific file
...
The pipe crc code slipped theough the net when we tried to
eliminate all crtc->index==pipe abuses. Remedy that.
And while at it get rid of those nasty intel_crtc+drm_crtc
pointer aliases.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210426185612.13223-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
DP v1.1+ says:
"The DisplayPort transmitter, which is the driving end for a request
transaction, pre-charges the AUX-CH+ and AUX-CH- to a common mode
voltage by transmitting 10 to 16 consecutive 0’s in Manchester II code.
After the active pre-charge, the transmitter sends an AUX Sync pattern.
The AUX Sync pattern must be as follows:
Start with 16 consecutive 0s in Manchester-II code, which results in
a transition from low to high in the middle of each bit period.
Including active pre-charge pulses, there shall be 26 to 32
consecutive 0s before the end of the AUX_SYNC pattern."
BDW bspec says:
"Used to determine the precharge time for the Aux Channel. During this
time the Aux Channel will drive the SYNC pattern. Every microsecond
gives one additional SYNC pulse beyond the hard coded 26 SYNC pulses.
The value is the number of microseconds times 2. Default is 3 decimal
which gives 6us of precharge which is 6 extra SYN pulses for a total
of 32."
CPT bspec says the same thing apart from:
"... Default is 5 decimal which gives 10us of precharge which is 10
extra SYNC pulses for a total of 36."
So it looks like to match the max of 32 of the DP spec we should just
always program this extra precharge time to 3.
Unfortunately g4x/ibx bspec doesn't have this clarification, but
since the cpt default was still the same 5 as for g4x/ibx let's
assume the behaviour was always the same.
I also did a bit more archaeology and found the following:
commit e3421a1894 ("drm/i915: enable DP/eDP for Sandybridge/Cougarpoint")
added the precharge==3 for snb
commit 092945e11c ("drm/i915/dp: Use auxch precharge value of 5 everywhere")
tried to change it to be 5 for snb
commit 6b4e0a93ff ("Revert "drm/i915/dp: Use auxch precharge value of 5 everywhere"")
went back to 3 for snb due to a regression
So I think the value of 5 was just always wrong, but I guess very
few display actually get upset if we do too many SYNCs. Also DP 1.0
did not specify any max value for this, whereas DP 1.1+ added the
max==32 wording.
Additionally I hooked up a scope to a few machines with the following
findings:
- ibx and cpt both give us the expected 32 total sync pulses with
precharge==3
- ctg is a bit different, it has the 10 hardcoded precharge sync
pulses same as later platforms (so we get at least 26 sync
pulses in total). However the additional precharge length (which
is what we're changing here) is not done with sync pulses.
Instead ctg does this part of the precharge with a steady DC
voltage. If we wanted to 100% match DP 1.1+ here we should perhaps
set prechange length to 0, but less precharge might make AUX less
reliable, and so far we're not aware of any problems due to the DC
precharge. Hence I think precharge==3 is probably the best choice
here too to make the total length of precharge consistent with
the later platforms.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210318181039.17260-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Add separate intel_dp_hdcp.h to go with intel_dp_hdcp.c, and rename the
init function intel_dp_hdcp_init() to follow naming where function
prefix matches the file name.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210427114520.4740-1-jani.nikula@intel.com
Since this is one of the few functions in drm_dp_mst_topology.c that
doesn't have any way of getting access to a drm_device, let's pass the
drm_dp_mst_topology_mgr down to this function so that it can use
drm_dbg_kms().
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210423184309.207645-14-lyude@redhat.com
Reviewed-by: Dave Airlie <airlied@redhat.com>
