Recently we came across requirement to identify EHL and JSL
platform to program them differently. Thus Split the basic
platform definition, macros, and PCI IDs to differentiate
between EHL and JSL platforms. Also, IS_ELKHARTLAKE is replaced
with IS_JSL_EHL everywhere.
Changes since V1 :
- Rebased to avoid merge conflicts
- Added missed check for jasperlake in intel_uc_fw.c
Cc : Matt Roper <matthew.d.roper@intel.com>
Cc : Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Tejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201013192948.63470-1-tejaskumarx.surendrakumar.upadhyay@intel.com
The DP Standard's recommendation is to use the LTTPR non-transparent
mode link training if LTTPRs are detected, so let's do this.
Besides power-saving, the advantages of this are that the maximum number
of LTTPRs can only be used in non-transparent mode (the limit is 5-8 in
transparent mode), and it provides a way to narrow down the reason for a
link training failure to a given link segment. Non-transparent mode is
probably also the mode that was tested the most by the industry.
The changes in this patchset:
- Pass the DP PHY that is currently link trained to all LT helpers, so
that these can access the correct LTTPR/DPRX DPCD registers.
- During LT take into account the LTTPR common lane rate/count and the
per LTTPR-PHY vswing/pre-emph limits.
- Switch to LTTPR non-transparent LT mode and train each link segment
according to the sequence in DP Standard v2.0 (complete CR/EQ for
each segment before continuing with the next segment).
v2:
- Switch to non-transparent mode during connector detection, which is
required before reading the per-PHY LTTPR capabilities.
- Move the DP_PHY_LTTPR() macro to drm_dp_helper.h (Ville)
- Use the new drm_dp_dpcd_read_phy_link_status() instead of adding the
same logic to intel_dp_get_link_status(). (Ville)
- Make intel_dp_lttpr_phy_caps() return a pointer to the whole array
instead of a pointer to its first element. (Ville)
- Add the intel_dp_phy_is_downstream_of_source() helper. (Ville)
- Add a code comment about the disable->enable quirk of
non-transparent mode.
- Add the intel_dp_training_pattern_set_reg() helper.
- Fix checkpatch/sparse warns.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007170917.1764556-7-imre.deak@intel.com
By default LTTPRs should be in transparent link training mode,
nevertheless in this patch we switch to this default mode explicitly.
The DP Standard recommends this, supposedly because an LTTPR may be left
in the non-transparent mode (by BIOS, previous kernel, or after reset
due to a firmware bug). I haven't seen this happening, but let's follow
the DP Standard.
v2:
- Add a code comment about the explicit disabling of non-transparent
mode.
v3:
- Move check to prevent initing LTTPRs on eDP to init_dp_lttpr_init().
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007170917.1764556-6-imre.deak@intel.com
Split the prepare, link training, fallback-handling steps into their own
functions for clarity and as a preparation for the upcoming LTTPR
changes.
While at it also:
- Unexport and inline intel_dp_set_idle_link_train(), which is used at a
single place.
- Add some documentation to functions that are exported or that can use
a better description about which part of the LT sequence they
implement.
v2: (Ville)
- Unexport/inline intel_dp_set_idle_link_train()
- Make the documentation of
intel_dp_prepare_link_train()/intel_dp_stop_link_train() more accurate
wrt. HW specific details.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007170917.1764556-3-imre.deak@intel.com
An LTTPR can be trained with training pattern 4 even if the DPCD
revision is < 1.4, but drm_dp_training_pattern_mask() would change
pattern 4 to pattern 3 on those DPCD revisions.
Since intel_dp_training_pattern() makes already sure that the proper
training pattern is used, all that needs to be masked out is the
scrambling disable flag, which is or'd to the mask later based on the
training pattern.
v2:
- Use a helper instead of open-coding the masking. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007170917.1764556-2-imre.deak@intel.com
Extend the eDP panel power cycle delay wait on reboot handling
to cover all platforms. No reason to think that VLV/CHV are
in any way special since the documentation states that the
hardware power cycle delay goes back to its default value on
reset, and that may not be enough for all panels.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201001151640.14590-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Currently VLV/CHV use a reboot notifier to make sure the panel
power cycle delay isn't violated across a system reboot. Replace
that with the new encoder .shutdown() hook.
And let's also stop overriding the power cycle delay with the
max value. No idea why the current code does that. The already
programmed delay should be correct.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201001151640.14590-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Recent update in documentation defeatured eDP HBR3 for EHL and JSL.
v2:
- Remove dead code in ehl_get_combo_buf_trans()
v3:
- Rebase
BSpec: 32247
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Vidya Srinivas <vidya.srinivas@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201005175447.93430-1-jose.souza@intel.com
Atm, if a full modeset is performed during the initial modeset the link
training will happen with uninitialized max DP rate and lane count. Make
sure the corresponding encoder state is initialized by adding an encoder
hook called during driver init and system resume.
A better alternative would be to store all states in the CRTC state and
make this state available for the link re-training code. Also instead of
the DPCD read in the hook there should be really a proper sink HW
readout in place. Both of these require a bigger rework, so for now opting
for this minimal fix to make at least full initial modesets work.
The patch is based on
https://patchwork.freedesktop.org/patch/101473/?series=10354&rev=3
v2: (Ville)
- s/sanitize_state/sync_state/
- No point in calling the hook when CRTC is disabled, remove the call.
- No point in calling the hook for MST, remove it.
v3: Check only DPCD_REV to avoid clobbering intel_dp->dpcd. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201005230154.1477653-1-imre.deak@intel.com
Some BIOSes set an unsupported/imprecise DP link rate (for instance on
TGL A stepping). Make sure that we do an encoder recompute and a modeset
in this case.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201003001846.1271151-4-imre.deak@intel.com
Move the checks to decide whether a fastset is possible during the
initial commit to an encoder hook. This check is really encoder specific
and the next patch will also require this adding a DP encoder specific
check.
v2: Fix negated condition in gen11_dsi_initial_fastset_check().
v3: Make sure to call the hook for all encoders on the crtc. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201005215311.1475666-1-imre.deak@intel.com
On HP 800 G4 DM, if HDMI cable isn't plugged before boot, the HDMI port
becomes useless and never responds to cable hotplugging:
[ 3.031904] [drm:lspcon_init [i915]] *ERROR* Failed to probe lspcon
[ 3.031945] [drm:intel_ddi_init [i915]] *ERROR* LSPCON init failed on port D
Seems like the lspcon chip on the system only gets powered after the
cable is plugged.
Consilidate lspcon_init() into lspcon_resume() to dynamically init
lspcon chip, and make HDMI port work.
v6:
- Rebase on latest for-linux-next.
v5:
- Consolidate lspcon_resume() with lspcon_init().
- Move more logic into lspcon code.
v4:
- Trust VBT in intel_infoframe_init().
- Init lspcon in intel_dp_detect().
v3:
- Make sure it's handled under long HPD case.
v2:
- Move lspcon_init() inside of intel_dp_hpd_pulse().
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/203
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200610075542.12882-1-kai.heng.feng@canonical.com
Now that we've plumbed the crtc state all the way down we can
eliminate the DP_TP_{CTL,STATUS} register offsets from intel_dp,
and instead we derive them directly from the crtc state.
And thus we can get rid of the nasty hack in intel_ddi_get_config()
which mutates intel_dp during the readout.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200929233449.32323-12-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Get rid of mode crtc->config usage, and some ad-hoc intel_dp state
usage by plumbing the crtc state all the way down to the link training
code.
Unfortunately we do have to keep some cached state in intel_dp so
that we can do the "does the link need retraining?" checks from
the short hpd handler.
v2: Add intel_crtc_state forward declaration
v3: Don't kill the PHY test code totally since it's
now in the hotplug work where we can get at the states
v4: Don't resurrect the debug scrambling disable bit (Imre)
Use intel_dp_mst_is_master_trans() (Imre)
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201001111053.24451-1-ville.syrjala@linux.intel.com
Doing any kind modeset stuff from the short hpd handler is
verboten. The ad-hoc PHY test modeset code violates this. And
by calling various link training related functions it's now
blocking further work to plumb the crtc state down into the
link training code.
Let's hack around that by pushing the PHY test stuff into the
hotplug work where it's less of a problem. Still not great but
at least acceptable. We take a few pages from the link retraining
handbook to handle the locking and whatnot.
v2: Fix the intel_dp_hotplug() return value
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200930100412.9313-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
When validating a "YCbCr 4:2:0 only" mode we must take into
account the fact that we're going to be outputting YCbCr
4:2:0 or 4:4:4 (when a DP->HDMI protocol converter is doing
the 4:2:0 downsampling). For YCbCr 4:4:4 the minimum output
bpc is 8, for YCbCr 4:2:0 it'll be half that. The currently
hardcoded 6bpc is only correct for RGB 4:4:4, which we will
never use with these kinds of modes. Figure out what we're
going to output and use the correct min bpp value to validate
whether the link has sufficient bandwidth.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200917214335.3569-3-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Pass the output_format directly to intel_dp_{min,output}_bpp()
rather than passing in the crtc_state and digging out the
output_format inside the functions. This will allow us to reuse
the functions for mode validation purposes.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200917214335.3569-2-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
For platforms that can't do native 4:2:0 outout we may still be
able to do it by getting the DP->HDMI protocol converter to
perform the 4:4:4->4:2:0 downsamling for us. In this case we
have to configure our hardware to output YCbCr 4:4:4, which we've
already hooked up so all we need to do is flip the switch.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200904115354.25336-19-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Account for the TMDS clock limits declared by the DFP
when determining what color depth we're going to use.
v2: Drop the reference to DP++ dongle since it's not handled here
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200904115354.25336-17-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DP 1.3 adds some extra control knobs for DP->HDMI protocol conversion.
Let's use that to configure the "HDMI mode" (ie. infoframes vs. not)
based on the capabilities of the sink.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200904115354.25336-13-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the new helpers to extract the TMDS clock limits from
the downstream facing port and check them in .mode_valid().
TODO: we should check these in .compute_config() too to eg.
determine if we can do deep color on the HDMI side or not
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200904115354.25336-12-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move the downstream facing port dotclock check into a new function
(intel_dp_mode_valid_downstream()) so that we have a nice future
place where we can collect other related checks.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200904115354.25336-10-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We want to differentiate between the DFP dotclock and TMDS clock
limits. Let's convert the current thing to just give us the
dotclock limit.
v2: Use Returns: for kdoc (Lyude)
Fix up nouveau code too
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200904115354.25336-9-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Deal with more cases in drm_dp_downstream_max_bpc():
- DPCD 1.0 -> assume 8bpc for non-DP
- DPCD 1.1+ DP (or DP++ with DP sink) -> allow anything
- DPCD 1.1+ TMDS -> check the caps, assume 8bpc if the value is crap
- anything else -> assume 8bpc
v2: Use Returns: for kdoc (Lyude)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200904115354.25336-8-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Stash the downstream facing port max bpc away during
intel_dp_set_edid(). We'll soon need the EDID in there so
we can't figure this out so easily during .compute_config() anymore.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200904115354.25336-6-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Non-HDMI sinks shouldn't be sent infoframes. Check for that when
using LSPCON.
FIXME: How do we turn off infoframes once enabled? Do we even
have to?
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200904115354.25336-3-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently DP/HDMI/DDI encoders init their hpd_pin from the
connector init. Let's move it to the encoder init so that
we don't need to add platform specific junk to the connector
init (which is shared by all g4x+ platforms).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200630215601.28557-10-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Since the display hardware is all there even when INTEL_DISPLAY_ENABLED
return false we have to be capable of shutting it down cleanly so
as to not anger the hw. To that end let's reduce the effect of
!INTEL_DISPLAY_ENABLE to just treating all outputs as disconnected.
Should prevent anyone from automagically enabling any of them, while
still allowing us to cleanly shut them down.
v2: Put the check into the right place for CRT
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200910164256.25983-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Since DP 1.3, it's been possible for DP receivers to specify an
additional set of DPCD capabilities, which can take precedence over the
capabilities reported at DP_DPCD_REV.
Basically any device supporting DP is going to need to read these in an
identical manner, in particular nouveau, so let's go ahead and just move
this code out of i915 into a shared DRM DP helper that we can use in
other drivers.
v2:
* Remove redundant dpcd[DP_DPCD_REV] == 0 check
* Fix drm_dp_dpcd_read() ret checks
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20200826182456.322681-20-lyude@redhat.com
And of course, we'll also need to read the sink count from other drivers
as well if we're checking whether or not it's supported. So, let's
extract the code for this into another helper.
v2:
* Fix drm_dp_dpcd_readb() ret check
* Add back comment and move back sink_count assignment in intel_dp_get_dpcd()
v5:
* Change name from drm_dp_get_sink_count() to drm_dp_read_sink_count()
* Also, add "See also:" section to kdocs
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20200826182456.322681-17-lyude@redhat.com
Since other drivers are also going to need to be aware of the sink count
in order to do proper dongle detection, we might as well steal i915's
DP_SINK_COUNT helpers and move them into DRM helpers so that other
dirvers can use them as well.
Note that this also starts using intel_dp_has_sink_count() in
intel_dp_detect_dpcd(), which is a functional change.
v5:
* Change name from drm_dp_has_sink_count() to
drm_dp_read_sink_count_cap()
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20200826182456.322681-16-lyude@redhat.com
We're going to be doing the same probing process in nouveau for
determining downstream DP port capabilities, so let's deduplicate the
work by moving i915's code for handling this into a shared helper:
drm_dp_read_downstream_info().
Note that when we do this, we also do make some functional changes while
we're at it:
* We always clear the downstream port info before trying to read it,
just to make things easier for the caller
* We skip reading downstream port info if the DPCD indicates that we
don't support downstream port info
* We only read as many bytes as needed for the reported number of
downstream ports, no sense in reading the whole thing every time
v2:
* Fixup logic for calculating the downstream port length to account for
the fact that downstream port caps can be either 1 byte or 4 bytes
long. We can actually skip fixing the max_clock/max_bpc helpers here
since they all check for DP_DETAILED_CAP_INFO_AVAILABLE anyway.
* Fix ret code check for drm_dp_dpcd_read
v5:
* Change name from drm_dp_downstream_read_info() to
drm_dp_read_downstream_info()
* Also, add "See Also" sections for the various downstream info
functions (drm_dp_read_downstream_info(), drm_dp_downstream_max_clock(),
drm_dp_downstream_max_bpc())
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200826182456.322681-14-lyude@redhat.com
Just a tiny drive-by cleanup, we can consolidate i915's code for
checking for MST support into a helper to be shared across drivers.
v5:
* Drop !!()
* Move drm_dp_has_mst() out of header
* Change name from drm_dp_has_mst() to drm_dp_read_mst_cap()
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Sean Paul <sean@poorly.run>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200826182456.322681-10-lyude@redhat.com
DRRS and PSR can't be enable together, so giving preference to PSR
as it allows more power-savings by complete shutting down display,
so to guarantee this, it should compute DRRS state after compute PSR.
Cc: Srinivas K <srinivasx.k@intel.com>
Cc: Hariom Pandey <hariom.pandey@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200825171331.17971-1-jose.souza@intel.com
Backmerging drm-next into drm-misc-next for nouveau and panel updates.
Resolves a conflict between ttm and nouveau, where struct ttm_mem_res got
renamed to struct ttm_resource.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Since DP-specific information is stored in driver's structures, every
driver needs to implement subconnector property by itself.
v2: updates to match previous commit changes
v3: rebase
v4: renamed a function call
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Signed-off-by: Jeevan B <jeevan.b@intel.com>
Signed-off-by: Oleg Vasilev <oleg.vasilev@intel.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com> #and acked for merging
Tested-by: Oleg Vasilev <oleg.vasilev@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1587732655-17544-2-git-send-email-jeevan.b@intel.com
The initial CI results did not include a TGL system which includes a
panel that is having issues with patch. Revert while we triage.
This reverts commit 680c45c767.
Signed-off-by: Matt Atwood <matthew.s.atwood@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200702230957.30536-1-matthew.s.atwood@intel.com
We have a mix of dport, intel_dport, intel_dig_port and dig_port to
reference a intel_digital_port struct. Numbers are around
5 intel_dport
36 dport
479 intel_dig_port
352 dig_port
Since we already removed the intel_ prefix from most of our other
structs, do the same here and prefer dig_port.
v2: rename everything in i915, not just a few display sources and
reword commit message (from Matt Roper)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200701045054.23357-1-lucas.demarchi@intel.com
intel_dp_set_source_rates() calls intel_dp_is_edp(), which is unsafe to
use before encoder_type is set. This caused GEN11+ to incorrectly strip
HBR3 from source rates for edp. Move intel_dp_set_source_rates() to
after encoder_type is set. Add comment to intel_dp_is_edp() describing
unsafe usages.
v2: Alter intel_dp_set_source_rates final position (Ville/Manasi).
Remove outdated comment (Ville).
Slight optimization of control flow in intel_dp_init_connector.
Slight rewording in commit message.
Signed-off-by: Matt Atwood <matthew.s.atwood@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200630233310.10191-1-matthew.s.atwood@intel.com
Catch up with upstream, in particular to get c1e8d7c6a7 ("mmap locking
API: convert mmap_sem comments").
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
UAPI Changes:
- Add DRM_MODE_TYPE_USERDEF for video modes specified in cmdline.
Cross-subsystem Changes:
- Assorted devicetree binding updates.
- Add might_sleep() to dma_fence_wait().
- Fix fbdev's get_user_pages_fast() handling, and use pin_user_pages.
- Small cleanup with IS_BUILTIN in video/fbdev drivers.
- Fix video/hdmi coding style for infoframe size.
Core Changes:
- Silence vblank output during init.
- Fix DP-MST corruption during send msg timeout.
- Clear leak in drm_gem_objecs_lookup().
- Make newlines work with force connector attribute.
- Fix module refcounting error in drm_encoder_slave, and use new i2c api.
- Header fix for drm_managed.c
- More struct_mutex removal for !legacy drivers:
- Remove gem_free_object()
- Removal of drm_gem_object_put_unlocked().
- Show current->comm alongside pid in debug printfs.
- Add drm_client_modeset_check() + drm_client_framebuffer_flush().
- Replace drm_fb_swab16 with drm_fb_swap that also supports 32-bits.
- Remove mode->vrefresh, and compactify drm_display_mode.
- Use drm_* macros for logging and warnings.
- Add WARN when drm_gem_get_pages is used on a private obj.
- Handle importing and imported dmabuf better in shmem helpers.
- Small fix for drm/mm hole size comparison, and remove invalid entry optimization.
- Add a drm/mm selftest.
- Set DSI connector type for DSI panels.
- Assorted small fixes and documentation updates.
- Fix DDI I2C device registration for MST ports, and flushing on destroy.
- Fix master_set return type, used by vmwgfx.
- Make the drm_set/drop_master ioctl symmetrical.
Driver Changes:
Allow iommu in the sun4i driver and use it for sun8i.
- Simplify backlight lookup for omap, amba-clcd and tilcdc.
- Hold reg_lock for rockchip.
- Add support for bridge gpio and lane reordering + polarity to ti-sn65dsi86, and fix clock choice.
- Small assorted fixes to tilcdc, vc4, i915, omap, fbdev/sm712fb, fbdev/pxafb, console/newport_con, msm, virtio, udl, malidp, hdlcd, bridge/ti-sn65dsi86, panfrost.
- Remove hw cursor support for mgag200, and use simple kms helper + shmem helpers.
- Add support for KOE Allow iommu in the sun4i driver and use it for sun8i.
- Simplify backlight lookup for omap, amba-clcd and tilcdc.
- Hold reg_lock for rockchip.
- Add support for bridge gpio and lane reordering + polarity to ti-sn65dsi86, and fix clock choice.
- Small assorted fixes to tilcdc, vc4 (multiple), i915.
- Remove hw cursor support for mgag200, and use simple kms helper + shmem helpers.
- Add support for KOE TX26D202VM0BWA panel.
- Use GEM CMA functions in arc, arm, atmel-hlcdc, fsi-dcu, hisilicon, imx, ingenic, komeda, malidp, mcde, meson, msxfb, rcar-du, shmobile, stm, sti, tilcdc, tve200, zte.
- Remove gem_print_info.
- Improve gem_create_object_helper so udl can use shmem helpers.
- Convert vc4 dt bindings to schemas, and add clock properties.
- Device initialization cleanups for mgag200.
- Add a workaround to fix DP-MST short pulses handling on broken hardware in i915.
- Allow build test compiling arm drivers.
- Use managed pci functions in mgag200 and ast.
- Use dev_groups in malidp.
- Add per pixel alpha support for PX30 VOP in rockchip.
- Silence deferred probe logs in panfrost.
-----BEGIN PGP SIGNATURE-----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=ZmKI
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2020-06-19' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.9:
UAPI Changes:
- Add DRM_MODE_TYPE_USERDEF for video modes specified in cmdline.
Cross-subsystem Changes:
- Assorted devicetree binding updates.
- Add might_sleep() to dma_fence_wait().
- Fix fbdev's get_user_pages_fast() handling, and use pin_user_pages.
- Small cleanup with IS_BUILTIN in video/fbdev drivers.
- Fix video/hdmi coding style for infoframe size.
Core Changes:
- Silence vblank output during init.
- Fix DP-MST corruption during send msg timeout.
- Clear leak in drm_gem_objecs_lookup().
- Make newlines work with force connector attribute.
- Fix module refcounting error in drm_encoder_slave, and use new i2c api.
- Header fix for drm_managed.c
- More struct_mutex removal for !legacy drivers:
- Remove gem_free_object()
- Removal of drm_gem_object_put_unlocked().
- Show current->comm alongside pid in debug printfs.
- Add drm_client_modeset_check() + drm_client_framebuffer_flush().
- Replace drm_fb_swab16 with drm_fb_swap that also supports 32-bits.
- Remove mode->vrefresh, and compactify drm_display_mode.
- Use drm_* macros for logging and warnings.
- Add WARN when drm_gem_get_pages is used on a private obj.
- Handle importing and imported dmabuf better in shmem helpers.
- Small fix for drm/mm hole size comparison, and remove invalid entry optimization.
- Add a drm/mm selftest.
- Set DSI connector type for DSI panels.
- Assorted small fixes and documentation updates.
- Fix DDI I2C device registration for MST ports, and flushing on destroy.
- Fix master_set return type, used by vmwgfx.
- Make the drm_set/drop_master ioctl symmetrical.
Driver Changes:
Allow iommu in the sun4i driver and use it for sun8i.
- Simplify backlight lookup for omap, amba-clcd and tilcdc.
- Hold reg_lock for rockchip.
- Add support for bridge gpio and lane reordering + polarity to ti-sn65dsi86, and fix clock choice.
- Small assorted fixes to tilcdc, vc4, i915, omap, fbdev/sm712fb, fbdev/pxafb, console/newport_con, msm, virtio, udl, malidp, hdlcd, bridge/ti-sn65dsi86, panfrost.
- Remove hw cursor support for mgag200, and use simple kms helper + shmem helpers.
- Add support for KOE Allow iommu in the sun4i driver and use it for sun8i.
- Simplify backlight lookup for omap, amba-clcd and tilcdc.
- Hold reg_lock for rockchip.
- Add support for bridge gpio and lane reordering + polarity to ti-sn65dsi86, and fix clock choice.
- Small assorted fixes to tilcdc, vc4 (multiple), i915.
- Remove hw cursor support for mgag200, and use simple kms helper + shmem helpers.
- Add support for KOE TX26D202VM0BWA panel.
- Use GEM CMA functions in arc, arm, atmel-hlcdc, fsi-dcu, hisilicon, imx, ingenic, komeda, malidp, mcde, meson, msxfb, rcar-du, shmobile, stm, sti, tilcdc, tve200, zte.
- Remove gem_print_info.
- Improve gem_create_object_helper so udl can use shmem helpers.
- Convert vc4 dt bindings to schemas, and add clock properties.
- Device initialization cleanups for mgag200.
- Add a workaround to fix DP-MST short pulses handling on broken hardware in i915.
- Allow build test compiling arm drivers.
- Use managed pci functions in mgag200 and ast.
- Use dev_groups in malidp.
- Add per pixel alpha support for PX30 VOP in rockchip.
- Silence deferred probe logs in panfrost.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/001cd9a6-405d-4e29-43d8-354f53ae4e8b@linux.intel.com
During the initial probing of an MST sink, MST core will determine the
sink's link bandwidth based on its own version of the sink link
rate/lane count caps it reads from the DPCD. At a later point (after
probing and 1 or more modesets) i915 may limit the link parameters wrt.
the original source/sink common caps above due to link training failures
during a modeset and the resulting link training fallback logic.
Based on the above a modeset following another modeset with a link
training error will compute the i915 HW specific and DP protocol timing
parameters (data/link M/N and MST TU values) taking into account only
the unlimited source/sink common caps, but not taking into account the
fallback limits. This will also let DRM core oversubscribe the actual
link bandwidth during the MST payload allocation.
Prevent the above problem by disabling the link training fallback on MST
links for now, until the MST probe time initialization and the MST
compute config logic can deal with changing link parameters.
The misconfigured timings lead at least to a
'Timed out waiting for DP idle patterns'
error.
v2: (Ville)
- Print link training error message on the MST path too.
- Clarify the problem in the commit log.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200616211146.23027-2-imre.deak@intel.com
Start using device specific parameters instead of module parameters for
most things. The module parameters become the immutable initial values
for i915 parameters. The device specific parameters in i915->params
start life as a copy of i915_modparams. Any later changes are only
reflected in the debugfs.
The stragglers are:
* i915.force_probe and i915.modeset. Needed before dev_priv is
available. This is fine because the parameters are read-only and never
modified.
* i915.verbose_state_checks. Passing dev_priv to I915_STATE_WARN and
I915_STATE_WARN_ON would result in massive and ugly churn. This is
handled by not exposing the parameter via debugfs, and leaving the
parameter writable in sysfs. This may be fixed up in follow-up work.
* i915.inject_probe_failure. Only makes sense in terms of the module,
not the device. This is handled by not exposing the parameter via
debugfs.
v2: Fix uc i915 lookup code (Michał Winiarski)
Cc: Juha-Pekka Heikkilä <juha-pekka.heikkila@intel.com>
Cc: Venkata Sandeep Dhanalakota <venkata.s.dhanalakota@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20200618150402.14022-1-jani.nikula@intel.com
Currently MST on a port can get enabled/disabled from the hotplug work
and get disabled from the short pulse work in a racy way. Fix this by
relying on the MST state checking in the hotplug work and just schedule
a hotplug work from the short pulse handler if some problem happened
during the MST interrupt handling.
This removes the explicit MST disabling in case of an AUX failure, but
if AUX fails, then probably the detection will also fail during the
scheduled hotplug work and it's not guaranteed that we'll see
intermittent errors anyway.
While at it also simplify the error checking of the MST interrupt
handler.
v2:
- Convert intel_dp_check_mst_status() to return bool. (Ville)
- Change the intel_dp->is_mst check to an assert, since after this patch
the condition can't change after we checked it previously.
- Document the return value from intel_dp_check_mst_status().
v3:
- Remove the intel_dp->is_mst check from intel_dp_check_mst_status().
There is no point in checking the same condition twice, even though
there is a chance that the hotplug work running concurrently changes
it.
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200605094801.17709-1-imre.deak@intel.com
Avoid a NULL dereference for a mismatched encoder type, hit when
probing state for all encoders.
This is a band aid to prevent the OOPS as the right fix is "probably to
swap the psr vs infoframes.enable checks, or outright disappear from
this function" (Ville).
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/1892
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200525124912.16019-1-chris@chris-wilson.co.uk
(cherry picked from commit 22da5d846d)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
According to the DP spec supporting vswing 1 + preemph 2 is
mandatory. We don't have the hw settings for that though. In
order to pretend to follow the DP spec let's just select
vswing 0 + preemph 2 in this case (the DP spec says to use
the requested preemph in preference to the vswing when the
requested values aren't supported).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200512174145.3186-4-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
cpt/ppt support pre-emphasis level 3. Let's actually declare
support for it, instead of clamping things to level 2.
Also tweak the if-ladder in intel_dp_voltage_max() to match
intel_dp_pre_emphasis_max() to make it easier to compare them.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200512174145.3186-2-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
The drrs code dereferences mode->vrefresh via some really long chain
of structures/pointers. Couldn't get coccinelle to see through all
that so let's add some local variables to help it.
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200428171940.19552-3-ville.syrjala@linux.intel.com
Make sure to select the port's AUX power domain while holding the TC
port lock. The domain depends on the port's current TC mode, which may
get changed under us if we're not holding the lock.
This was left out from
commit 8c10e22626 ("drm/i915: Keep the TypeC port mode fixed for detect/AUX transfers")
Cc: <stable@vger.kernel.org> # v5.4+
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514204553.27193-1-imre.deak@intel.com
(cherry picked from commit ae9b6cfe13)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Make sure to select the port's AUX power domain while holding the TC
port lock. The domain depends on the port's current TC mode, which may
get changed under us if we're not holding the lock.
This was left out from
commit 8c10e22626 ("drm/i915: Keep the TypeC port mode fixed for detect/AUX transfers")
Cc: <stable@vger.kernel.org> # v5.4+
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514204553.27193-1-imre.deak@intel.com
In order to use a common VSC SDP Colorimetry calculating code on PSR,
it adds a compute routine for PSR VSC SDP.
As PSR routine can not use infoframes.vsc of crtc state, it also adds new
writing of DP SDPs (Secondary Data Packet) for PSR.
PSR routine has its own scenario and timings of writing a VSC SDP.
v3: Replace a structure name to drm_dp_vsc_sdp from intel_dp_vsc_sdp
v4: Use struct drm_device logging macros
v10: 1) Fix packing of VSC SDP where Pixel Encoding/Colorimetry Format is
not supported.
2) Change a checking of PSR state.
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-14-gwan-gyeong.mun@intel.com
In order to use computed config for DP SDPs (DP VSC SDP and DP HDR Metadata
Infoframe SDP), it replaces intel_dp_vsc_enable() function and
intel_dp_hdr_metadata_enable() function to intel_dp_set_infoframes()
function.
And it removes unused functions.
Before:
intel_dp_vsc_enable() and intel_dp_hdr_metadata_enable() compute sdp
configs and program sdp registers on enable callback of encoder.
After:
It separates computing of sdp configs and programming of sdp register.
The compute config callback of encoder calls computing sdp configs.
The enable callback of encoder calls programming sdp register.
v3: Rebased
v5: Polish commit message [Uma]
v10: Rebased
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-8-gwan-gyeong.mun@intel.com
It adds code to read the DP SDPs from the video DIP and unpack them into
the crtc state.
It adds routines that read out DP VSC SDP and DP HDR Metadata Infoframe SDP
In order to unpack DP VSC SDP, it adds intel_dp_vsc_sdp_unpack() function.
It follows DP 1.4a spec. [Table 2-116: VSC SDP Header Bytes] and
[Table 2-117: VSC SDP Payload for DB16 through DB18]
In order to unpack DP HDR Metadata Infoframe SDP, it adds
intel_dp_hdr_metadata_infoframe_sdp_unpack(). And it follows DP 1.4a spec.
([Table 2-125: INFOFRAME SDP v1.2 Header Bytes] and
[Table 2-126: INFOFRAME SDP v1.2 Payload Data Bytes - DB0 through DB31])
and CTA-861-G spec. [Table-42 Dynamic Range and Mastering InfoFrame].
A naming rule and style of intel_read_dp_sdp() function references
intel_read_infoframe() function of intel_hdmi.c
v2: Minor style fix
v3: Replace a structure name to drm_dp_vsc_sdp from intel_dp_vsc_sdp
v4: Use struct drm_device logging macros
v5: Addressed review comments from Uma
- Polish commit message and comments
- Combine the if checks of sdp.HB2 and sdp.HB3
- Add 6bpc to unpacking of VSC SDP
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-3-gwan-gyeong.mun@intel.com
Get rid of several platform specific variants of
intel_digital_port_connected() and just use the ISR bits we've
stashed away.
v2: Duplicate stuff to avoid exposing platform specific
functions across files (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200311155422.3043-4-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Let's get rid of the platform if ladders in
intel_digital_port_connected() and make it a vfunc. Now the if
ladders are at the encoder initialization which makes them a bit
less convoluted.
v2: Add forward decl for intel_encoder in intel_tc.h
v3: Duplicate stuff to avoid exposing platform specific
functions across files (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200311155422.3043-2-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Pass the entire connector state to intel_{gmch,pch}_panel_fitting().
For now we just need to get at .scaling_mode but in the future we'll
want access to the margin properties as well.
v2: Deal with intel_dp_ycbcr420_config()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200422161917.17389-5-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Fix skl_update_scaler_crtc() to deal with different scaling
modes correctly. The current implementation assumes
DRM_MODE_SCALE_FULLSCREEN. Fortunately we don't expose any
border properties currently so the code does actually end
up doing the right thing (assigning a scaler for pfit).
The code does need to be fixed before any borders are
exposed.
Also we have redundant calls to skl_update_scaler_crtc() in
dp/hdmi .compute_config() which can be nuked. They were anyway
called before we had even computed the pfit state so were
basically nonsense. The real call we need to keep is in
intel_crtc_atomic_check().
v2: Deal witrh skl_update_scaler_crtc() in intel_dp_ycbcr420_config()
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200422161917.17389-1-ville.syrjala@linux.intel.com
Remove a number of inlines from .c files, and let the compiler decide
what's best. There's more to do, but need to start somewhere, and need
to start setting the example.
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200420140438.14672-2-jani.nikula@intel.com
We shouldn't try to do link retraining from the short hpd handler.
We can't take any modeset locks there so this is racy as hell.
Push the whole thing into the hotplug work like we do with SST.
We'll just have to adjust the SST retraining code to deal with
the MST encoders and multiple pipes.
TODO: I have a feeling we should just rip this all out and
do a full modeset instead. Stuff like port sync and the tgl+
MST master transcoder stuff maybe doesn't work well if we
try to retrain without following the proper modeset sequence.
So far haven't done any actual tests to confirm that though.
Cc: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200417152734.464-2-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Make intel_dp_check_mst_status() somewhat legible by humans.
Note that the return value of drm_dp_mst_hpd_irq() is always
either 0 or -ENOMEM, and we never did anything with the latter
so we can just ignore the whole thing.
We can also get rid of the direct drm_dp_mst_topology_mgr_set_mst(false)
call since returning -EINVAL causes the caller to do the very same call
for us.
Cc: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200417152734.464-1-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
The variable test_result is being initialized with a value that is
never read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200417160829.112776-1-colin.king@canonical.com
Right now dp.regs.dp_tp_ctl/status are only set during the encoder
pre_enable() hook, what is causing all reads and writes to those
registers to go to offset 0x0 before pre_enable() is executed.
So if i915 takes the BIOS state and don't do a modeset any following
link retraing will fail.
In the case that i915 needs to do a modeset, the DDI disable sequence
will write to a wrong register not disabling DP 'Transport Enable' in
DP_TP_CTL, making a HDMI modeset in the same port/transcoder to
not light up the monitor.
So here for GENs older than 12, that have those registers fixed at
port offset range it is loading at encoder/port init while for GEN12
it will keep setting it at encoder pre_enable() and during HW state
readout.
Fixes: 4444df6e20 ("drm/i915/tgl: move DP_TP_* to transcoder")
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200414230442.262092-1-jose.souza@intel.com
Add connector debugfs attributes for each intel
connector which is getting register.
v2:
- adding connector debugfs for each connector in
intel_connector_register() to fix CI failure for legacy connectors.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200415170555.15531-4-anshuman.gupta@intel.com
This patch process phy compliance request by programming requested
vswing, pre-emphasis and test pattern.
v1: Initial patch.
v2: Fixes added during testing with test-scope. (Khaled/Clint/Manasi)
- pipe used as argument during registers programming instead of port.
- TRANS_CONF must be disable/enable as well during ddi disable/enable.
- harcoded PLTPAT 80 bit custom pattern as the DPR-100 does not set it
in the sink’s DPCDs
- TRANS_DDI_FUNC_CTL DDI_Select (Bits 27:30) need to reset/set during
disable/enable.
v3: used macros instead of numbers and some cosmetic changes. [Manasi]
Cc: Clinton Taylor <Clinton.A.Taylor@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200316103759.12867-8-animesh.manna@intel.com
During DP phy compliance auto test mode, sink will request
combination of different test pattern with differnt level of
vswing, pre-emphasis. Function added to prepare for it.
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200316103759.12867-5-animesh.manna@intel.com
On TypeC connectors we need to retry the detection after hotplug events
for a longer time, so add a retry counter to support this. The next
patch will add detection retries on TypeC ports needing this.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200330095425.29113-1-imre.deak@intel.com
We're going to want access to the atomic state for iterating
the slave crtcs when enabling the port sync master crtc. Pass
the atomic state all the way down.
The alternative would be yet another encoder hook which we'll
have to call after all the normal modeset stuff is done. Not
really a fan of yet another hook just for this.
Note that during readout state sanitation we are now going
to pass NULL as the atomic state since we don't have one.
We need to change that and then we can also s/crtc_state/crtc/
and s/conn_state/conn/ for the encoder hooks as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200313164831.5980-13-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Transcoder port sync was introduced to the hardware in BDW. We
can trivially enable it for SKL+ since the same codepaths are
already used for ICL+ port sync. The only difference is the actual
location of the bits we need to poke.
We leave BDW out (at least for now) since it uses different modeset
paths that haven't been adapted for port sync, and IIRC using the
feature would involve some extra workarounds we've not implemented.
Pre-BDW hardware does not support port sync so we'd have to tweak
the modeset sequence to start the pipes as close together as possible
and hope for the best. So far no one has seriously tried to implement
that.
Closes: https://gitlab.freedesktop.org/drm/intel/issues/27
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200313164831.5980-9-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
-----BEGIN PGP SIGNATURE-----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=I0vz
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2020-04-01' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"This is the main drm pull request for 5.7-rc1.
Highlights:
- i915 enables Tigerlake by default
- i915 and amdgpu have initial OLED backlight support
[ Jani Nikula pipes up and points out that we've had a bunch of
"initial support" code for a long time already, but only now
Lyude made it actually work on real world machines ]
- vmwgfx add support to enable OpenGL 4 userspace
- zero length arrays are mostly removed.
Detailed summary:
new driver:
- tidss: TI Keystone platform display subsystem
core:
- new drm device warn macros
- mode config valid for memory constrained devices
- bridge bus format negotation
- consolidated fake vblank event handling
- dma_alloc related cleanups
- drop get_crtc callback
- dp: DP1.4 EDID corruption test
- EDID CEA detailed timings improvements
- relicense some code to dual GPL2/MIT
- convert core vblank support to per-crtc support
- rework drm_global_mutex
- bridge rework to allow omap_dss custom driver removeal
- remove drm_fb_helper connector interrfaces
- zero-length array removal
scheduler:
- support for modifying the sched list
- revert job distribution optimization
- helper to pick least loaded scheduler
- race condition fix
mst:
- various fixes
- remove register_connector callback
i915:
- uapi to allows userspace specific CS ring buffer sizes
- Tigerlake enablement patches + Tigerlake enabled by default
- new sysfs entries for engine properties
- display/logging refactors
- eDP/DP fixes for DPCD
- Gen7 back to aliasing-ppgtt
- Gen8+ irq refactor
- Avoid globals
- GEM locking fixes and simplifications
- Ice Lake and Elkhart Lake fixes and workarounds
- Baytrail/Haswell instability fix
- GVT - VFIO edid better support
amdgpu:
- Rework VM update handling in preparation for HMM support
- drm load/unload removal fixups
- USB-C PD firmware updates
- HDCP srm support
- Navi/renoir PM watermark fixes
- OLED panel support
- Optimize debugging vram access
- Use BACO for runtime pm
- DC clock programming optimizations and fixes
- PSP fw loading sequence updates
- Drop DRIVER_USE_AGP
- Remove legacy drm load and unload callbacks
- ACP Kconfig fix
- Lots of fixes across the driver
amdkfd:
- runtime pm support
- more gfx config details in amdgpu
radeon:
- drop DRIVER_USE_AGP
vmwgfx:
- Disable DMA when SEV encryption in use
- Shader Model 5 support - needed for GL4 support
msm:
- DPU resource manager refactor
- dpu using atomic global state
mediatek:
- MT8183 DPI support
etnaviv:
- out-of-bounds read fix
- expose feature flags for GC400 STM32MP1 SoC
- runtime suspend entry fix
- dma32 zone fix
hisilicon:
- mode selection fixes
meson:
- YUV420 support
lima:
- add support for heap buffers
tinydrm:
- removal of owner field
- explicit DT dependency removal
- YAML schema conversion
tegra:
- misc cleanups
tidss:
- new driver
virtio:
- better batching of notifications to host
- memory handling reworked
- shmem + gpu context fixes
hibmc:
- add gamma_set support
- improve DPMS support
pl111:
- Integrator IM-PD1 support
sun4i:
- LVDS support for A20 + A33
- DSI panel handling improvements"
* tag 'drm-next-2020-04-01' of git://anongit.freedesktop.org/drm/drm: (1537 commits)
drm/i915/display: Fix mode private_flags comparison at atomic_check
drm/i915/gt: Stage the transfer of the virtual breadcrumb
drm/i915/gt: Select the deepest available parking mode for rc6
drm/i915: Avoid live-lock with i915_vma_parked()
drm/i915/gt: Treat idling as a RPS downclock event
drm/i915/gt: Cancel a hung context if already closed
drm/i915: Use explicit flag to mark unreachable intel_context
drm/amdgpu: don't try to reserve training bo for sriov (v2)
drm/amdgpu/smu11: add support for SMU AC/DC interrupts
drm/amdgpu/swSMU: handle manual AC/DC notifications
drm/amdgpu/swSMU: handle DC controlled by GPIO for navi1x
drm/amdgpu/swSMU: set AC/DC mode based on the current system state (v2)
drm/amdgpu/swSMU: correct the bootup power source for Navi1X (v2)
drm/amdgpu/swSMU: use the smu11 power source helper for navi1x
drm/amdgpu/smu11: add a helper to set the power source
drm/amd/swSMU: add callback to set AC/DC power source (v2)
drm/scheduler: fix rare NULL ptr race
drm/amdgpu: fix the coverage issue to clear ArcVPGRs
drm/amd/display: Fix pageflip event race condition for DCN.
drm/[radeon|amdgpu]: Remove HAINAN board from max_sclk override check
...
Avoid using the uninitialised len along the impossible error path to
shut the compiler up:
drivers/gpu/drm/i915/display/intel_dp.c:4928 intel_write_dp_sdp() error: uninitialized symbol 'len'.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200325140754.12636-1-chris@chris-wilson.co.uk
Few edp panels like Sharp is triggering short and long
hpd pulse after panel is getting powered off.
Currently driver is already ignoring long pulse for eDP
panel but in order to process the short pulse, it turns on
the VDD which requires panel power_cycle_delay + panel_power_on_delay
these delay on Sharp panel introduced the responsiveness overhead
of 800ms in the modeset sequence and as well is in suspend
sequence.
Ignoring any short pulse if panel is powered off.
FIXME: It requires to wait for panel_power_off delay in order
to check the panel power status due to pps_lock because panel triggers
short pulse immediately after writing PP_OFF to PP_CTRL register and
wait_panel_off waits for panel_power_off delay with pps_lock held.
This still creates responsiveness overhead of panel_power_off delay.
v2:
- checking vdd along with panel power to ignore the hpd. [Jani,Ville]
v3:
- safer side check to ignore the long hpd when eDP have power,
adding type of hpd to debug log. [Jani]
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200318081837.23983-1-anshuman.gupta@intel.com
It adds routines that write DP VSC SDP and DP HDR Metadata Infoframe SDP.
In order to pack DP VSC SDP, it adds intel_dp_vsc_sdp_pack() function.
It follows DP 1.4a spec. [Table 2-116: VSC SDP Header Bytes] and
[Table 2-117: VSC SDP Payload for DB16 through DB18]
In order to pack DP HDR Metadata Infoframe SDP, it adds
intel_dp_hdr_metadata_infoframe_sdp_pack() function.
And it follows DP 1.4a spec.
([Table 2-125: INFOFRAME SDP v1.2 Header Bytes] and
[Table 2-126: INFOFRAME SDP v1.2 Payload Data Bytes - DB0 through DB31])
and CTA-861-G spec. [Table-42 Dynamic Range and Mastering InfoFrame].
A mechanism and a naming rule of intel_dp_set_infoframes() function
references intel_encoder->set_infoframes() of intel_hdmi.c .
VSC SDP is used for PSR and Pixel Encoding and Colorimetry Formats cases.
Because PSR routine has its own routine of writing a VSC SDP, when the PSR
is enabled, intel_dp_set_infoframes() does not write a VSC SDP.
v3:
- Explicitly disable unused DIPs (AVI, GCP, VS, SPD, DRM. They will be
used for HDMI), when intel_dp_set_infoframes() function will be called.
- Replace a structure name to drm_dp_vsc_sdp from intel_dp_vsc_sdp.
v4: Use struct drm_device logging macros
v5:
- use intel_de_*() functions for register access
- Addressed review comments from Uma
Polish commit message and comments
Add 6bpc to packing of VSC SDP
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200211074657.231405-5-gwan-gyeong.mun@intel.com
It stores computed dp hdr metadata infoframe sdp to infoframes.drm of
crtc state. It referenced intel_hdmi_compute_drm_infoframe().
While computing, we'll also fill out the infoframes.enable bitmask
appropriately.
v2: Wrap a long line.
v4: Use struct drm_device logging macros
v5: Fix typo [Uma]
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200211074657.231405-4-gwan-gyeong.mun@intel.com
In order to support state readout for DP VSC SDP, we need to have a
structure which holds DP VSC SDP payload data such as
"union hdmi_infoframe drm" which is used for DRM infoframe.
It adds a struct drm_dp_vsc_sdp vsc to intel_crtc_state.infoframes.
And it stores computed dp vsc sdp to infoframes.vsc of crtc state.
While computing we'll also fill out the inforames.enable bitmask
appropriately.
The compute routine follows DP 1.4 spec [Table 2-117: VSC SDP Payload for
DB16 through DB18].
v3: Replace a structure name to drm_dp_vsc_sdp from intel_dp_vsc_sdp
v5:
- Rebased
- Add warning where a bpc is 6 and a pixel format is RGB.
v7: Fix the wrong check of combination bpc 6 and RGB pixelformat
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200211074657.231405-3-gwan-gyeong.mun@intel.com
This fixes a problem found on the MacBookPro 2017 Retina panel.
The panel reports 10 bpc color depth in its EDID, and the
firmware chooses link settings at boot which support enough
bandwidth for 10 bpc (324000 kbit/sec = multiplier 0xc),
but the DP_MAX_LINK_RATE dpcd register only reports
2.7 Gbps (multiplier value 0xa) as possible, in direct
contradiction of what the firmware successfully set up.
This restricts the panel to 8 bpc, not providing the full
color depth of the panel.
This patch adds a quirk specific to the MBP 2017 15" Retina
panel to add the additiional 324000 kbps link rate during
edp setup.
Link to previous discussion of a different attempted fix
with Ville and Jani:
https://patchwork.kernel.org/patch/11325935/
v2: Follow Jani's proposal of defining quirk_rates[] instead
of just appending 324000. This for better clarity.
v3: Rebased onto current drm-tip, as of 16-March-2020. Adapt
to new edid_quirks parameter of drm_dp_has_quirk().
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Tested-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200316042340.4783-1-mario.kleiner.de@gmail.com
The whole point of using OUIs is so that we can recognize certain
devices and potentially apply quirks for them. Normally this should work
quite well, but there appears to be quite a number of laptop panels out
there that will fill the OUI but not the device ID. As such, for devices
like this I can't imagine it's a very good idea to try relying on OUIs
for applying quirks. As well, some laptop vendors have confirmed to us
that their panels have this exact issue.
So, let's introduce the ability to apply DP quirks based on EDID
identification. We reuse the same quirk bits for OUI-based quirks, so
that callers can simply check all possible quirks using
drm_dp_has_quirk().
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200211183358.157448-2-lyude@redhat.com
DP shim's config_stream_type considered to be succeeded when
return value of intel_dp_hdcp2_write_msg() equals to size of
message to be written, it makes config_stream_type to return
a zero success value in order to succeed the HDCP auth.
v2:
- config_stream_type() returns 0 on success. [Ram]
CC: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303073838.25871-1-anshuman.gupta@intel.com
Some devices with a builtin panel have the panel mounted upside down,
this is indicated by the rotate_180 bit in the BDB_GENERAL_FEATURES VBT
block.
We store this info in dev_priv->vbt.orientation, use this to set the
connector's orientation property so that fbcon and userspace will show
the image the right way up on devices with an upside-down mounted panel.
This fixes the image being upside-down on a Teclast X89 tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228114110.187792-3-hdegoede@redhat.com
The #include has been splattered all over the place, but there are
precious few places, all .c files, that actually need it.
v2: remove leftover double newlines
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200225133131.3301-1-jani.nikula@intel.com
Some DSI and VBT pending patches from Hans will apply
cleanly and with less ugly conflicts if they are rebuilt
on top of other patches that recently landed on drm-next.
Reference: https://patchwork.freedesktop.org/series/70952/
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com
Restore the previous WARN_ON(cond) so that we don't complain about poor
old Cherryview.
Fixes: eb020ca3d4 ("drm/i915/display/dp: Make WARN* drm specific where drm_device ptr is available")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200223173959.3885742-1-chris@chris-wilson.co.uk
Currently we only set the DRM_CONNECTOR_POLL_{DISCONNECT,CONNECT}
bits in intel_connector->polled (the base setting), leading to
some confusing looking code to reset drm_connector->polled
(the actual setting) to DRM_CONNECTOR_POLL_HPD. Let's set
intel_connector->polled = DRM_CONNECTOR_POLL_HPD for all hpd
capable connectors, and then we don't need so many special
cases in the hotplug code.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200205183546.9291-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
UAPI Changes:
- lima: Add support for heap buffers
Cross-subsystem Changes:
Core Changes:
- Implement mode_config mode_valid for memory constrained drivers
- Bus format negociation between bridges
- Consolidate fake vblank events for drivers without vblank interrupts
- drm/bufs: dma_alloc related cleanups
- drm/dp_mst: Various fixes
- drm/print: New drm_device based print helpers
- Thomas is a drm-misc maintainer now!
Driver Changes:
- DPMS cleanups for atomic drivers
- Removal of owner field in SPI tinydrm drivers
- Removal of explicit dependency on DT for tinydrm drivers
- Conversion to YAML schemas for DT bindings
- tidss: New driver
- virtio: various reworks and fixes
- Our usual dozen or so new panels or bridges
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXkEjOgAKCRDj7w1vZxhR
xeaDAQD+1MludG4RmfQhATe4jTsPC1r2x63OF2CA0ChMGHXJyQEA8qqQ+8y1Cd/u
PZ3PpcTl4qYYHgzJ6FwW7kDPTvlaZQE=
=IJAt
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2020-02-10' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.7:
UAPI Changes:
- lima: Add support for heap buffers
Cross-subsystem Changes:
Core Changes:
- Implement mode_config mode_valid for memory constrained drivers
- Bus format negociation between bridges
- Consolidate fake vblank events for drivers without vblank interrupts
- drm/bufs: dma_alloc related cleanups
- drm/dp_mst: Various fixes
- drm/print: New drm_device based print helpers
- Thomas is a drm-misc maintainer now!
Driver Changes:
- DPMS cleanups for atomic drivers
- Removal of owner field in SPI tinydrm drivers
- Removal of explicit dependency on DT for tinydrm drivers
- Conversion to YAML schemas for DT bindings
- tidss: New driver
- virtio: various reworks and fixes
- Our usual dozen or so new panels or bridges
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20200210093421.xu4sofldm6wm6xq6@gilmour.lan
If one of the synced crtcs needs a full modeset, we need
to make sure all the synced crtcs are forced a full
modeset.
v3:
* Remove ~BIT(cpu_trans) which is a nop (Ville)
* use get_new_crtc_state and remove error check (Ville)
v2:
* Add tiles based on cpu_trans check (Ville)
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200214114126.13192-3-manasi.d.navare@intel.com
The i915_debugfs.c has grown more than a little unwieldy. Split out the
display related debugfs code to a file of its own under display/,
initialized with a separate call. No functional changes.
v2:
- Also moved i915_frontbuffer_tracking, i915_gem_framebuffer,
i915_power_domain_info, i915_dmc_info, i915_ipc_status (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200211161451.6867-2-jani.nikula@intel.com
Call cpu_latency_qos_add/update/remove_request() instead of
pm_qos_add/update/remove_request(), respectively, because the
latter are going to be dropped.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
The aux ch is used for more than DDC, so let's give it a better
name. For maximum ease let's include both the AUX ch identifier
and the port identifier (for cases where the VBT has redefined
the relationship of the two).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200123154542.12271-3-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Life is usually easier when we pass around intel_ types instead
of drm_ types. In this case it might not be, but I think being
consistent is a good thing anyway. Also some of this might get
cleaned up a bit more later as we keep propagating the intel_
types further.
@find@
identifier F =~ "^intel_attached_.*";
identifier C;
@@
F(struct drm_connector *C)
{
...
}
@@
identifier find.F;
identifier find.C;
@@
F(
- struct drm_connector *C
+ struct intel_connector *connector
)
{
<...
- C
+ &connector->base
...>
}
@@
identifier find.F;
expression C;
@@
- F(C)
+ F(to_intel_connector(C))
@@
expression C;
@@
- to_intel_connector(&C->base)
+ C
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191204180549.1267-3-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Not every platform needs quirk detection for panel orientation, so
split the drm_connector_init_panel_orientation_property into two
functions. One for platforms without the need for quirks, and the
other for platforms that need quirks.
Hans de Goede (changes in v2):
Rename the function from drm_connector_init_panel_orientation_property
to drm_connector_set_panel_orientation[_with_quirk] and pass in the
panel-orientation to set.
Beside the rename, also make the function set the passed in value
only once, if the value was set before (to a value other then
DRM_MODE_PANEL_ORIENTATION_UNKNOWN) make any further set calls a no-op.
This change is preparation for allowing the user to override the
panel-orientation for any connector from the kernel commandline.
When the panel-orientation is overridden this way, then we must ignore
the panel-orientation detection done by the driver.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200105155120.96466-1-hdegoede@redhat.com
I missed a few assert_pipe_disabled() cases when changing it to
take enum transcoder instead of enum pipe, making sparse unhappy.
Convert the leftovers.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200108145616.7349-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Fixes coccicheck warning:
drivers/gpu/drm/i915/display/intel_dp.c:4950:1-33: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/i915/display/intel_dp.c:4906:1-33: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ma Feng <mafeng.ma@huawei.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1578013959-31486-3-git-send-email-mafeng.ma@huawei.com
We are currently using a mix of platform name and acronym to name the
functions. Let's prefer the acronym as it should be clear what platform
it's about and it's shorter, so it doesn't go over 80 columns in a few
cases. This converts ironlake to ilk where appropriate.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191224084012.24241-7-lucas.demarchi@intel.com
UAPI Changes:
- Add support for DMA-BUF HEAPS.
Cross-subsystem Changes:
- mipi dsi definition updates, pulled into drm-intel as well.
- Add lockdep annotations for dma_resv vs mmap_sem and fs_reclaim.
- Remove support for dma-buf kmap/kunmap.
- Constify fb_ops in all fbdev drivers, including drm drivers and drm-core, and media as well.
Core Changes:
- Small cleanups to ttm.
- Fix SCDC definition.
- Assorted cleanups to core.
- Add todo to remove load/unload hooks, and use generic fbdev emulation.
- Assorted documentation updates.
- Use blocking ww lock in ttm fault handler.
- Remove drm_fb_helper_fbdev_setup/teardown.
- Warning fixes with W=1 for atomic.
- Use drm_debug_enabled() instead of drm_debug flag testing in various drivers.
- Fallback to nontiled mode in fbdev emulation when not all tiles are present. (Later on reverted)
- Various kconfig indentation fixes in core and drivers.
- Fix freeing transactions in dp-mst correctly.
- Sean Paul is steping down as core maintainer. :-(
- Add lockdep annotations for atomic locks vs dma-resv.
- Prevent use-after-free for a bad job in drm_scheduler.
- Fill out all block sizes in the P01x and P210 definitions.
- Avoid division by zero in drm/rect, and fix bounds.
- Add drm/rect selftests.
- Add aspect ratio and alternate clocks for HDMI 4k modes.
- Add todo for drm_framebuffer_funcs and fb_create cleanup.
- Drop DRM_AUTH for prime import/export ioctls.
- Clear DP-MST payload id tables downstream when initializating.
- Fix for DSC throughput definition.
- Add extra FEC definitions.
- Fix fake offset in drm_gem_object_funs.mmap.
- Stop using encoder->bridge in core directly
- Handle bridge chaining slightly better.
- Add backlight support to drm/panel, and use it in many panel drivers.
- Increase max number of y420 modes from 128 to 256, as preparation to add the new modes.
Driver Changes:
- Small fixes all over.
- Fix documentation in vkms.
- Fix mmap_sem vs dma_resv in nouveau.
- Small cleanup in komeda.
- Add page flip support in gma500 for psb/cdv.
- Add ddc symlink in the connector sysfs directory for many drivers.
- Add support for analogic an6345, and fix small bugs in it.
- Add atomic modesetting support to ast.
- Fix radeon fault handler VMA race.
- Switch udl to use generic shmem helpers.
- Unconditional vblank handling for mcde.
- Miscellaneous fixes to mcde.
- Tweak debug output from komeda using debugfs.
- Add gamma and color transform support to komeda for DOU-IPS.
- Add support for sony acx424AKP panel.
- Various small cleanups to gma500.
- Use generic fbdev emulation in udl, and replace udl_framebuffer with generic implementation.
- Add support for Logic PD Type 28 panel.
- Use drm_panel_* wrapper functions in exynos/tegra/msm.
- Add devicetree bindings for generic DSI panels.
- Don't include drm_pci.h directly in many drivers.
- Add support for begin/end_cpu_access in udmabuf.
- Stop using drm_get_pci_dev in gma500 and mga200.
- Fixes to UDL damage handling, and use dma_buf_begin/end_cpu_access.
- Add devfreq thermal support to panfrost.
- Fix hotplug with daisy chained monitors by removing VCPI when disabling topology manager.
- meson: Add support for OSD1 plane AFBC commit.
- Stop displaying garbage when toggling ast primary plane on/off.
- More cleanups and fixes to UDL.
- Add D32 suport to komeda.
- Remove globle copy of drm_dev in gma500.
- Add support for Boe Himax8279d MIPI-DSI LCD panel.
- Add support for ingenic JZ4770 panel.
- Small null pointer deference fix in ingenic.
- Remove support for the special tfp420 driver, as there is a generic way to do it.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEuXvWqAysSYEJGuVH/lWMcqZwE8MFAl34lkkACgkQ/lWMcqZw
E8M76g//WRYl9fWnV063s44FBVJYjGxaus0vQJSGidaPCIE6Ep6TNjXp8DVzV82M
HR79P9glL02DC9B8pflioNNXdIRGSVk/FJcKVB2seFAqEFCAknvWDM/X/y+mOUpp
fUeFl+Znlwx3YlM8f4Qujdbm+CbTewfbya4VAWeWd8XG2V8jfq5cmODPPlUMNenZ
J6Ja+W3ph741uSIfAKaP69LVJgOcuUjXINE4SWhRk/i5QF3GIRej/A7ZjWGLQ/t2
2zUUF7EiCzhPomM40H3ddKtXb4ZjNJuc5pOD4GpxR8ciNbe2gUOHEZ5aenwYBdsU
5MwbxNKyMbKXATtn3yv3fSc4jH3DtmEKpmovONeO8ZDBrQBnxeYa3tQvfkNghA2f
acoZMzYUImV+ft6DMIgpXppASvo7mQYDAbLPOGEJ9E44AL4UP00jesEjnK5FOHSR
3BEzGUnK/6QL5zFNPni8YZQ8dan4jDIno1mqIV+cQ4WCGlaKckzIWO6243Bf13b/
kROSJpgWkiK6Ngq0ofhD0MHyT/m1QnqUzWRKTJhRtPflSWRBsDZqWCQ5Vx1QlNIE
/HfTNbTpXWwa+5wXbbB8TkDw5t9cQGnR+QcrEd9HgoIec7B5Re8rx9i0TJAT4N05
03RCQCecSfD8gwKd2wgaFIpFGRl9lTdLYSpffSmyL2X5a20lZhM=
=b15X
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-12-16' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.6:
UAPI Changes:
- Add support for DMA-BUF HEAPS.
Cross-subsystem Changes:
- mipi dsi definition updates, pulled into drm-intel as well.
- Add lockdep annotations for dma_resv vs mmap_sem and fs_reclaim.
- Remove support for dma-buf kmap/kunmap.
- Constify fb_ops in all fbdev drivers, including drm drivers and drm-core, and media as well.
Core Changes:
- Small cleanups to ttm.
- Fix SCDC definition.
- Assorted cleanups to core.
- Add todo to remove load/unload hooks, and use generic fbdev emulation.
- Assorted documentation updates.
- Use blocking ww lock in ttm fault handler.
- Remove drm_fb_helper_fbdev_setup/teardown.
- Warning fixes with W=1 for atomic.
- Use drm_debug_enabled() instead of drm_debug flag testing in various drivers.
- Fallback to nontiled mode in fbdev emulation when not all tiles are present. (Later on reverted)
- Various kconfig indentation fixes in core and drivers.
- Fix freeing transactions in dp-mst correctly.
- Sean Paul is steping down as core maintainer. :-(
- Add lockdep annotations for atomic locks vs dma-resv.
- Prevent use-after-free for a bad job in drm_scheduler.
- Fill out all block sizes in the P01x and P210 definitions.
- Avoid division by zero in drm/rect, and fix bounds.
- Add drm/rect selftests.
- Add aspect ratio and alternate clocks for HDMI 4k modes.
- Add todo for drm_framebuffer_funcs and fb_create cleanup.
- Drop DRM_AUTH for prime import/export ioctls.
- Clear DP-MST payload id tables downstream when initializating.
- Fix for DSC throughput definition.
- Add extra FEC definitions.
- Fix fake offset in drm_gem_object_funs.mmap.
- Stop using encoder->bridge in core directly
- Handle bridge chaining slightly better.
- Add backlight support to drm/panel, and use it in many panel drivers.
- Increase max number of y420 modes from 128 to 256, as preparation to add the new modes.
Driver Changes:
- Small fixes all over.
- Fix documentation in vkms.
- Fix mmap_sem vs dma_resv in nouveau.
- Small cleanup in komeda.
- Add page flip support in gma500 for psb/cdv.
- Add ddc symlink in the connector sysfs directory for many drivers.
- Add support for analogic an6345, and fix small bugs in it.
- Add atomic modesetting support to ast.
- Fix radeon fault handler VMA race.
- Switch udl to use generic shmem helpers.
- Unconditional vblank handling for mcde.
- Miscellaneous fixes to mcde.
- Tweak debug output from komeda using debugfs.
- Add gamma and color transform support to komeda for DOU-IPS.
- Add support for sony acx424AKP panel.
- Various small cleanups to gma500.
- Use generic fbdev emulation in udl, and replace udl_framebuffer with generic implementation.
- Add support for Logic PD Type 28 panel.
- Use drm_panel_* wrapper functions in exynos/tegra/msm.
- Add devicetree bindings for generic DSI panels.
- Don't include drm_pci.h directly in many drivers.
- Add support for begin/end_cpu_access in udmabuf.
- Stop using drm_get_pci_dev in gma500 and mga200.
- Fixes to UDL damage handling, and use dma_buf_begin/end_cpu_access.
- Add devfreq thermal support to panfrost.
- Fix hotplug with daisy chained monitors by removing VCPI when disabling topology manager.
- meson: Add support for OSD1 plane AFBC commit.
- Stop displaying garbage when toggling ast primary plane on/off.
- More cleanups and fixes to UDL.
- Add D32 suport to komeda.
- Remove globle copy of drm_dev in gma500.
- Add support for Boe Himax8279d MIPI-DSI LCD panel.
- Add support for ingenic JZ4770 panel.
- Small null pointer deference fix in ingenic.
- Remove support for the special tfp420 driver, as there is a generic way to do it.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ba73535a-9334-5302-2e1f-5208bd7390bd@linux.intel.com
Move intel_dp_source_supports_dsc() from intel_dp.c as
intel_dsc_source_support() in intel_vdsc.c. The DSC source support is
more about DSC than about DP, and will be needed for DP independent
code.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6c9f646090913290fb00efd46a4332421bf95930.1575974743.git.jani.nikula@intel.com
Turns out future DSI specific parameters aren't workable with the
approach of having the encoder specific functions in intel_vdsc.c. Make
intel_dsc_compute_params() a helper that does the encoder independent
parts, and have encoder code call it. Move intel_dsc_dp_compute_params()
to intel_dp.c as intel_dp_dsc_compute_params().
No functional changes.
v2: Rename pipe_config to crtc_state while at it.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/620688ec302f7f49cc539c6c1653bfaf6092fce0.1575974743.git.jani.nikula@intel.com
intel_hdcp_transcoder_config() is clobbering some globally visible
state in .compute_config(). That is a big no no as .compute_config()
is supposed to have no visible side effects when either the commit
fails or it's just a TEST_ONLY commit.
Inline this stuff into intel_hdcp_enable() so that the state only
gets modified when we actually commit the state to the hardware.
Cc: Ramalingam C <ramalingam.c@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Fixes: 39e2df090c ("drm/i915/hdcp: update current transcoder into intel_hdcp")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191204180549.1267-2-ville.syrjala@linux.intel.com
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
(cherry picked from commit 67e1d5ed85)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
intel_hdcp_transcoder_config() is clobbering some globally visible
state in .compute_config(). That is a big no no as .compute_config()
is supposed to have no visible side effects when either the commit
fails or it's just a TEST_ONLY commit.
Inline this stuff into intel_hdcp_enable() so that the state only
gets modified when we actually commit the state to the hardware.
Cc: Ramalingam C <ramalingam.c@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Fixes: 39e2df090c ("drm/i915/hdcp: update current transcoder into intel_hdcp")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191204180549.1267-2-ville.syrjala@linux.intel.com
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
When looking at SDEISR to determine the connection status of combo
outputs, we should use the phy index rather than the port index.
Although they're usually the same thing, EHL's DDI-D (port D) is
attached to PHY-A and SDEISR doesn't even have bits for a "D" output.
It's also possible that future platforms may map DDIs (the internal
display engine programming units) to PHYs (the output handling on the IO
side) in ways where port!=phy, so let's look at the PHY index by
default.
v2: Rename to intel_combo_phy_connected. (Lucas)
Fixes: 719d240026 ("drm/i915/ehl: Enable DDI-D")
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191127221314.575575-2-matthew.d.roper@intel.com
(cherry picked from commit 3d1e388d40)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
When looking at SDEISR to determine the connection status of combo
outputs, we should use the phy index rather than the port index.
Although they're usually the same thing, EHL's DDI-D (port D) is
attached to PHY-A and SDEISR doesn't even have bits for a "D" output.
It's also possible that future platforms may map DDIs (the internal
display engine programming units) to PHYs (the output handling on the IO
side) in ways where port!=phy, so let's look at the PHY index by
default.
v2: Rename to intel_combo_phy_connected. (Lucas)
Fixes: 719d240026 ("drm/i915/ehl: Enable DDI-D")
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191127221314.575575-2-matthew.d.roper@intel.com
The South Display is part of the PCH so we should technically be basing
our port detection logic off the PCH in use rather than the platform
generation.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191127221314.575575-1-matthew.d.roper@intel.com
Starting with gen12, PORT_A can be connected to a transcoder
with audio support. Modify the existing logic that disabled
audio on PORT_A unconditionally.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191125125313.17584-1-kai.vehmanen@linux.intel.com
Backmerge to get dfce90259d ("Backmerge i915 security patches from
commit 'ea0b163b13ff' into drm-next") and thus 100d46bd72 ("Merge
Intel Gen8/Gen9 graphics fixes from Jon Bloomfield.").
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Split out the DP specific parts, making it easier to add DSI specific
configuration. Also move the encoder specific parts towards the end, to
allow overriding generic configuration if needed. This also improves
clarity by making it clear the encoder independent configuration does
not depend on the encoder specific parts.
v2: Rebase
Cc: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191104141439.26312-3-jani.nikula@intel.com
UAPI Changes:
- Make context persistence optional
Allow userspace to tie the context lifetime to FD lifetime,
effectively allowing Ctrl-C killing of a process to also clean
up the hardware immediately.
Compute changes: https://github.com/intel/compute-runtime/pull/228
The compute driver is shipping in Ubuntu. uAPI acked by Mesa folks.
- Put future HW and their uAPIs under STAGING & BROKEN
Introduces DRM_I915_UNSTABLE Kconfig menu for working on the new
uAPI for future HW in upstream. We already disable driver loading
by default the platform is deemed ready. This is a second level
of protection based on compile time switch (STAGING & BROKEN).
- Under DRM_I915_UNSTABLE: Add the fake lmem region on iGFX
Fake local memory region on integrated GPU through cmdline:
memmap=2G$16G i915.fake_lmem_start=0x400000000
Currently allows testing non-mappable GGTT behavior and running
kernel selftest for local memory.
Driver Changes:
- Fix Bugzilla #112084: VGA external monitor not working (Ville)
- Add support for half float framebuffers (Ville)
- Add perf support on TGL (Lionel)
- Replace hangcheck by heartbeats (Chris)
- Allow SPT PCH on all AML devices (James)
- Add new CNL PCH for CML platform (Imre)
- Allow 100 ms (Kconfig) for workloads to exit before reset (Chris, Jon, Joonas)
- Forcibly pre-empt a context after 100 ms (Kconfig) of delay (Chris)
- Make timeslice duration Kconfig configurable (Chris)
- Whitelist PS_(DEPTH|INVOCATION)_COUNT for Tigerlake (Tapani)
- Support creating LMEM objects in kernel (Matt A)
- Adjust the location of RING_MI_MODE in the context image for TGL (Chris)
- Handle AUX interrupts for TC ports (Matt R)
- Add support for devices without mappable GGTT aperture (Daniele)
- Rename "inject_load_failure" module parameter to "inject_probe_failure" (Janusz)
- Handle fused off HDCP, FBC, DMC and DSC (Jose)
- Add support to one DP-MST stream on Tigerlake (Lucas)
- Add HuC firmware (and GuC) for TGL (Daniele)
- Allow ICL+ DSI on any pipe (Ville)
- Check some transcoder timing minimum limits (Ville)
- Don't set queue_priority_hint if we don't kick the submission (Chris)
- Introduce barrier pulses along engines to flush idle/in-flight requests (Chris)
- Drop assertion that ce->pin_mutex guards state updates (Chris)
- Cancel banned contexts on schedule-out (Chris)
- Cancel contexts when hangchecking is disabled (Chris)
- Catch GTT fault errors for gen11+ planes (Matt R)
- Print in debugfs if PSR is not enabled because of sink (Jose)
- Do not set MOCS control values on dgfx (Lucas)
- Setup io-mapping for LMEM (Abdiel)
- Support kernel mapping of LMEM objects (Abdiel)
- Add LMEM selftests (Matt A)
- Initialise PMU spinlock before registering (Chris)
- Clear DKL_TX_PMD_LANE_SUS before program TC voltage swing (Jose)
- Flip interpretation of ips fmin/fmax to max rps (Chris)
- Add VBT compression parameter block definition (Jani)
- Limit the blitter sizes to ensure low preemption latency (Chris)
- Fixup block_size rounding on BLT (Matt A)
- Don't try to place HWS in non-existing mappable region (Michal Wa)
- Don't allocate the ring in stolen if we lack aperture (Matt A)
- Add AUX B & C to DC_OFF_POWER_DOMAINS for Tigerlake (Matt R)
- Avoid HPD poll detect triggering a new detect cycle (Imre)
- Document the userspace fail with possible_crtcs (Ville)
- Drop lrc header page now unused by GuC (Daniele)
- Do not switch aux to TBT mode for non-TC ports (Jose)
- Restructure code to avoid depending on i915 but smaller structs (Chris, Tvrtko, Andi)
- Remove pm park/unpark notifications (Chris)
- Avoid lockdep cross-contamination between object types (Chris)
- Restructure DSC code (Jani)
- Fix dead locking in early workload shadow (Zhenyu)
- Split the legacy submission backend from the common CS ring buffer (Chris)
- Move intel_engine_context_in/out into intel_lrc.c (Tvrtko)
- Describe perf/wakeref structure members in documentation (Anna)
- Update renamed header files names in documentation (Anna)
- Add debugs to distingiush a cd2x update from a full cdclk pll update (Ville)
- Rework atomic global state locking (Ville)
- Allow planes to declare their minimum acceptable cdclk (Ville)
- Eliminate skl_check_pipe_max_pixel_rate() and simplify skl_max_scale() (Ville)
- Making loglevel of PSR2/SU logs same (Ap)
- Capture aux page table error register (Lionel)
- Add is_dgfx to device info (Jose)
- Split gen11_irq_handler to make it shareable (Lucas)
- Encapsulate kconfig constant values inside boolean predicates (Chris)
- Split memory_region initialisation into its own file (Chris)
- Use _PICK() for CHICKEN_TRANS() and add CHICKEN_TRANS_D (Ville)
- Add perf helper macros for comparing with whitelisted registers (Umesh)
- Fix i915_inject_load_error() name to read *_probe_* (Janusz)
- Drop unused AUX register offsets (Matt R)
- Provide more information on DP AUX failures (Matt R)
- Add GAM/SFC instdone to error state (Mika)
- Always track callers to intel_rps_mark_interactive() (Chris)
- Nuke 'mode' argument to intel_get_load_detect_pipe() (Ville)
- Simplify LVDS crtc_mask and pipe_mask setup (Ville)
- Stop frobbing crtc->base.mode (Ville)
- Do s/crtc_mask/pipe_mask/ (Ville)
- Split detaching and removing the vma (Chris)
- Selftest improvements (Chris, Tvrtko, Mika, Matt A, Lionel)
- GuC code improvements (Rob, Andi, Daniele)
- Check against i915_selftest only under CONFIG_SELFTEST (Chris)
- Refine occupancy test in kill_context() (Chris)
- Start kthreads before stopping (Chris)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191101104718.GA14323@jlahtine-desk.ger.corp.intel.com
Split up crtc_state->base to uapi. This is done using the following patch,
ran after the previous commit that splits out any hw references:
@@
struct intel_crtc_state *T;
@@
-T->base
+T->uapi
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-5-maarten.lankhorst@linux.intel.com
Split up crtc_state->base to hw where appropriate. This is done using the following patch:
@@
struct intel_crtc_state *T;
identifier x =~ "^(active|enable|degamma_lut|gamma_lut|ctm|mode|adjusted_mode)$";
@@
-T->base.x
+T->hw.x
@@
struct drm_crtc_state *T;
identifier x =~ "^(active|enable|degamma_lut|gamma_lut|ctm|mode|adjusted_mode)$";
@@
-to_intel_crtc_state(T)->base.x
+to_intel_crtc_state(T)->hw.x
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-4-maarten.lankhorst@linux.intel.com
Non-TC ports always have tc_mode == TC_PORT_TBT_ALT so it was
switching aux to TBT mode for all combo-phy ports, happily this did
not caused any issue but is better follow BSpec.
Also this is reserved bit before ICL.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Fixes: e9b7e1422d ("drm/i915: Sanitize the terminology used for TypeC port modes")
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191029011014.286885-1-jose.souza@intel.com
