We shouldn't really trust tc_mode on non-TC PHYs since we never
initialize it explicitly. So let's check for the PHY type first.
Fortunately TC_PORT_TBT_ALT happens to be zero so I don't think
there's an actual bug here, just a possibility for a future one
if someone rearranges the enum values.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210128155948.13678-5-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
In thunderbolt mode the PHY is owned by the thunderbolt controller.
We are not supposed to touch it. So skip the vswing programming
as well (we already skipped the other steps not applicable to TBT).
Touching this stuff could supposedly interfere with the PHY
programming done by the thunderbolt controller.
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210128155948.13678-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Add changes to configure port clock registers for ADL-S. Combo phy port
clocks are configured by DPCLKA_CFGCR0 and DPCLKA_CFGCR1 registers.
The DDI to internal clock mappings in DPCLKA_CFGCR0 register for ADL-S
translates to
DDI A -> DDIA
DDI B -> USBC1
DDI I -> USBC2
For DPCLKA_CFGCR1
DDI J -> USBC3
DDI K -> USBC4
Bspec: 50287
Bspec: 53812
Bspec: 53723
v2: Replace I915_READ() with intel_de_read().(Jani)
v3:
- Use reg variable to assign ADLS specific registers inorder to replace
branching with intel_de_read/write() calls.(mdroper)
- Reuse icl_get_ddi_pll() for ADLS to fix issue with updating active
dpll on driver load.(aswarup)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210125140753.347998-7-aditya.swarup@intel.com
If VRR is enabled, the sink should ignore MSA parameters
and regenerate incoming video stream without depending
on these parameters. Hence set the MSA_TIMING_PAR_IGNORE_EN
bit if VRR is enabled.
Reset this bit on VRR disable.
v2:
* ACtually set the dpcd msa ignore bit (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-13-manasi.d.navare@intel.com
This patch disables the VRR enable and VRR PUSH
bits in the HW during commit modeset disable sequence.
Thsi disable will happen when the port is disabled
or when the userspace sets VRR prop to false and
requests to disable VRR.
v2:
* Use intel_de_rmw (Jani N)
v3:
* Remove rmw (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-12-manasi.d.navare@intel.com
This patch computes the VRR parameters from VRR crtc states
and configures them in VRR registers during CRTC enable in
the modeset enable sequence.
v2:
* Remove initialization to 0 (Jani N)
* Use correct pipe %c (Jani N)
v3:
* Remove debug prints (Ville)
* Use cpu_trans instead of pipe for TRANS_VRR regs (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-10-manasi.d.navare@intel.com
Get rid of the "I like my random new style best" approach and unify
the handling for the DDI buf trans table sanity checks once again.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201207203512.1718-2-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
The MH PHY vswing table does have all the entries these days. Get
rid of the old hacks in the code which claim otherwise.
This hack was totally bogus anyway. The correct way to handle the
lack of those two entries would have been to declare our max
vswing and pre-emph to both be level 2.
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Clinton Taylor <clinton.a.taylor@intel.com>
Fixes: 9f7ffa2979 ("drm/i915/tc/icl: Update TC vswing tables")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201207203512.1718-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
I accidentally added the compliance test hacks only to
intel_dp_hotplug() which doesn't even get used on any DDI
platform. Put the same crap into intel_ddi_hotplug().
Cc: Imre Deak <imre.deak@intel.com>
Fixes: 193af12cd6 ("drm/i915: Shove the PHY test into the hotplug work")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210114205046.8247-7-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
In a long overdue refactoring, split out all panel sequencer code from
intel_dp.c to new intel_pps.[ch].
The first part is mostly just code movement as-is, without cleanups or
functional changes.
We need to add a vlv_get_dpll() helper to get at the vlv/chv dpll from
pps code.
v2: Rebase.
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/14cc59d5734432ad976cd49ff8efce8fa413e5b2.1610127741.git.jani.nikula@intel.com
hdcp_port_data is specific to a port on which HDCP
encryption is getting enabled, so encapsulate it to
intel_digital_port.
This will be required to enable HDCP 2.2 stream encryption.
v2:
- 's/port_data/hdcp_port_data'. [Ram]
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-12-anshuman.gupta@intel.com
Both HDCP_{1.x,2.x} requires to select/deselect Multistream HDCP bit
in TRANS_DDI_FUNC_CTL in order to enable/disable stream HDCP
encryption over DP MST Transport Link.
HDCP 1.4 stream encryption requires to validate the stream encryption
status in HDCP_STATUS_{TRANSCODER,PORT} register driving that link
in order to enable/disable the stream encryption.
Both of above requirement are same for all Gen with respect to
B.Spec Documentation.
v2:
- Cosmetic changes function name, error msg print and
stream typo fixes. [Uma]
v3:
- uniformity for connector detail in DMESG. [Ram]
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-8-anshuman.gupta@intel.com
Gen12 has H/W delta with respect to HDCP{1.x,2.x} display engine
instances lies in Transcoder instead of DDI as in Gen11.
This requires hdcp driver to use mst_master_transcoder for link
authentication and stream transcoder for stream encryption
separately.
This will be used for both HDCP 1.4 and HDCP 2.2 over DP MST
on Gen12.
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-6-anshuman.gupta@intel.com
DG1's vswing tables are the same for eDP and HDMI but have slight
differences from ICL/TGL for DP.
v2:
- Use a "_hbr2_hbr3" suffix on the table name to make it more clear
that the same table is used for both HBR2 and HBR3 link rates.
(Swathi)
Bspec: 49291
Cc: Clinton Taylor <Clinton.A.Taylor@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Cc: Swathi Dhanavanthri <swathi.dhanavanthri@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210108222528.1954514-1-matthew.d.roper@intel.com
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
There was some misinterpretation of specification, when DDIX_USED is
set, the next bit means 0 for DP and 1 for HDMI.
Anyways this misinterpretation is not causing any issues, this change
is just to comply with specification.
Also as for us it do not matters if it is HDMI or DP, not checking the
port type that HTI is using.
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210108134802.21280-1-jose.souza@intel.com
The bspec has been updated with new vswing programming for RKL DP. No
data is provided for HDMI or eDP, so for now we'll continue to assume
that those are the same as TGL.
Bspec: 49291
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218040535.45492-1-matthew.d.roper@intel.com
Reviewed-by: Swathi Dhanavanthri <swathi.dhanavanthri@intel.com>
If PCON has capability to convert RGB->YCbCr colorspace and also
to 444->420 downsampling then for any YUV420 only mode, we can
let the PCON do all the conversion. If the PCON supports
RGB->YCbCr conversion for all BT2020, BT709, BT601, choose
the one that is selected by userspace via connector colorspace
property, otherwise default to BT601.
v2: As suggested by Uma Shankar, considered case for colorspace
BT709 and BT2020, and default to BT601. Also appended dir
'display' in commit message.
v3: Fixed typo in condition for printing one of the error msg.
v4: As suggested by Uma Shankar:
-Fixed bug in determining the colorspace for RGB->YCbCr conversion.
-Fixed minor formatting issues
Also updated the commit message as per latest changes.
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
[Jani: Fixed checkpatch PARENTHESIS_ALIGNMENT.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-16-ankit.k.nautiyal@intel.com
When a source supporting DSC1.1 is connected to DSC1.2 HDMI2.1 sink
via DP HDMI2.1 PCON, the PCON can be configured to decode the
DSC1.1 compressed stream and encode to DSC1.2. It then sends the
DSC1.2 compressed stream to the HDMI2.1 sink.
This patch configures the PCON for DSC1.1 to DSC1.2 encoding, based
on the PCON's DSC encoder capablities and HDMI2.1 sink's DSC decoder
capabilities.
v2: Addressed review comments from Uma Shankar:
-fixed the error in packing pps parameter values
-added check for pcon in the pcon related function
-appended display in commit message
v3: Only consider non-zero DSC FRL b/w for determining max FRL b/w
supported by sink.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
[Jani: Fixed checkpatch BRACES, LINE_SPACING, PARENTHESIS_ALIGNMENT.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-15-ankit.k.nautiyal@intel.com
This patch calls functions to check FRL training requirements
for an HDMI2.1 sink, when connected through PCON.
The call is made before the DP link training. In case FRL is not
required or failure during FRL training, the TMDS mode is selected
for the pcon.
v2: moved check_frl_training() just after FEC READY, before
starting DP link training.
v3: rebase
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-11-ankit.k.nautiyal@intel.com
The Bspec does not mention polling the FEC Enable
Live status bit. That is only there for debug purposes.
So remove the polling from driver.
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201125072634.27664-1-manasi.d.navare@intel.com
Lspcon has Infoframes as well as DIP for HDR metadata(DRM Infoframe).
Create a separate mechanism for lspcon compared to HDMI in order to
address the same and ensure future scalability.
v2: Streamlined this as per Ville's suggestions, making sure that
HDMI infoframe versions are directly returned instead of a redundant
and confusing DIP overhead.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201130204738.2443-12-uma.shankar@intel.com
Skip iterating over bigjoiner slaves, only the master has the state we
care about.
Add the width of the bigjoiner slave to the reconstructed fb.
Hide the bigjoiner slave to userspace, and double the mode on bigjoiner
master.
And last, disable bigjoiner slave from primary if reconstruction fails.
v3:
* Fix the ddi_get_config slave error (Ankit Nautiyal)
v2:
* Unsupported bigjoiner config for initial fb (Ville)
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
[vsyrjala:
* Don't do any hw->uapi state copy for bigjoiner slave
* We still have hw.mode so no need to pass it in
* Appease checkpatch]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201117194718.11462-7-manasi.d.navare@intel.com
Enabling is done in a special sequence and so should plane updates
be. Ideally the end user never notices the second pipe is used.
This way ideally everything will be tear free, and updates are
really atomic as userspace expects it.
This uses generic modeset_enables() calls like trans port sync
but still has special handling for disable since for slave we
should not disable things like encoder, plls that are not enabled
for slave.
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
[vsyrjala: Appease checkpatch]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201117194718.11462-6-manasi.d.navare@intel.com
Make vdsc work when no output is enabled. The big joiner needs VDSC
on the slave, so enable it and set the appropriate bits.
So remove encoder usage from dsc functions.
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201117194718.11462-5-manasi.d.navare@intel.com
I totally fumbled the ?: usage when generating the DDI encoder
names. Reverse the things that need reversing, and to make it
a bit less messy add a few macros to hide the arithmetic on the
port enums.
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Fixes: 2d709a5a62 ("drm/i915: Give DDI encoders even better names")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201117154028.8516-1-ville.syrjala@linux.intel.com
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Currently the DPLL .get_freq() uses pll->state.hw_state which
is not the thing we actually read out (except during driver
load/resume). Outside of that pll->state.hw_state is just the
thing we committed last time around. During state check we
just read the thing into crtc_state->dpll_hw_state, so that
is what we should use for calculating the DPLL output frequency.
I think we used to do this so that the results of the readout
were actually used, but somehow it got changed when the
.get_freq() refactoring happened.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201109231239.17002-3-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
JSL has update in vswing table for eDP.
BSpec: 21257
Changes since V1:
- Fixed few checkpatch errors
Cc: Souza Jose <jose.souza@intel.com>
Signed-off-by: Tejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201020053657.99890-1-tejaskumarx.surendrakumar.upadhyay@intel.com
DG1 uses 2 registers for the ddi clock mapping, with PHY A and B using
DPCLKA_CFGCR0 and PHY C and D using DPCLKA1_CFGCR0. Hide this behind a
single macro that chooses the correct register according to the phy
being accessed, use the correct bitfields for each pll/phy and implement
separate functions for DG1 since it doesn't share much with ICL/TGL
anymore.
The previous values were correct for PHY A and B since they were using
the same register as before and the bitfields were matching.
v2: Add comment and try to simplify DG1_DPCLKA* macros by reusing
previous ones
v3:
- Fix DG1_DPCLKA_CFGCR0_DDI_CLK_SEL_MASK() after wrong macro reuse
- Move phy -> id map to a separate macro (Aditya)
- Remove DG1_DPCLKA_CFGCR0_DDI_CLK_SEL_MASK where not required
(Aditya)
- Use drm_WARN_ON
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Clinton Taylor <Clinton.A.Taylor@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Aditya Swarup <aditya.swarup@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Aditya Swarup <aditya.swarup@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201106210006.837953-1-lucas.demarchi@intel.com
Let's pimp the DDI encoder->name to reflect what the spec calls them.
Ie. on pre-tgl DDI A-F, on tgl+ DDI A-C or DDI TC1-6.
Also since each encoder is really a combination of the DDI and the PHY
we include the PHY name as well.
ICL is a bit special since it already has the two different types
of DDIs (combo or TC) but it still calls them just DDI A-F regarless
of the type. For that let's add an extra "(TC)" note to remind
is which type of DDI it really is.
The code is darn ugly, but not sure there's much we can do about it.
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201028213323.5423-4-ville.syrjala@linux.intel.com
DG1 has one more combo phy port, no TC and all irq handling goes through
SDE, like for MCC.
v2: Also change intel_hpd_pin_default() to include DG1 mapping
v3, v4: Rebase on hpd refactor
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201021082034.3170478-2-lucas.demarchi@intel.com
Rename intel_dp_sink_dpms() to intel_dp_set_power()
so one doesn't always have to convert from the DPMS
enum values to the actual DP D-states.
Also when dealing with a branch device this has nothing to
do with any sink, so the old name was nonsense anyway.
Also adjust the debug message accordingly, and pimp it
with the standard encoder id+name thing.
Trivial bits done with cocci:
@@
expression DP;
@@
(
- intel_dp_sink_dpms(DP, DRM_MODE_DPMS_OFF)
+ intel_dp_set_power(DP, DP_SET_POWER_D3)
|
- intel_dp_sink_dpms(DP, DRM_MODE_DPMS_ON)
+ intel_dp_set_power(DP, DP_SET_POWER_D0)
)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201016194800.25581-2-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Recently we came across requirement to identify EHL and JSL
platform to program them differently. Thus Split the basic
platform definition, macros, and PCI IDs to differentiate
between EHL and JSL platforms. Also, IS_ELKHARTLAKE is replaced
with IS_JSL_EHL everywhere.
Changes since V1 :
- Rebased to avoid merge conflicts
- Added missed check for jasperlake in intel_uc_fw.c
Cc : Matt Roper <matthew.d.roper@intel.com>
Cc : Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Tejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201013192948.63470-1-tejaskumarx.surendrakumar.upadhyay@intel.com
An LTTPR can be trained with training pattern 4 even if the DPCD
revision is < 1.4, but drm_dp_training_pattern_mask() would change
pattern 4 to pattern 3 on those DPCD revisions.
Since intel_dp_training_pattern() makes already sure that the proper
training pattern is used, all that needs to be masked out is the
scrambling disable flag, which is or'd to the mask later based on the
training pattern.
v2:
- Use a helper instead of open-coding the masking. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007170917.1764556-2-imre.deak@intel.com
Extend the eDP panel power cycle delay wait on reboot handling
to cover all platforms. No reason to think that VLV/CHV are
in any way special since the documentation states that the
hardware power cycle delay goes back to its default value on
reset, and that may not be enough for all panels.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201001151640.14590-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Recent update in documentation defeatured eDP HBR3 for EHL and JSL.
v2:
- Remove dead code in ehl_get_combo_buf_trans()
v3:
- Rebase
BSpec: 32247
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Vidya Srinivas <vidya.srinivas@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201005175447.93430-1-jose.souza@intel.com
Atm, if a full modeset is performed during the initial modeset the link
training will happen with uninitialized max DP rate and lane count. Make
sure the corresponding encoder state is initialized by adding an encoder
hook called during driver init and system resume.
A better alternative would be to store all states in the CRTC state and
make this state available for the link re-training code. Also instead of
the DPCD read in the hook there should be really a proper sink HW
readout in place. Both of these require a bigger rework, so for now opting
for this minimal fix to make at least full initial modesets work.
The patch is based on
https://patchwork.freedesktop.org/patch/101473/?series=10354&rev=3
v2: (Ville)
- s/sanitize_state/sync_state/
- No point in calling the hook when CRTC is disabled, remove the call.
- No point in calling the hook for MST, remove it.
v3: Check only DPCD_REV to avoid clobbering intel_dp->dpcd. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201005230154.1477653-1-imre.deak@intel.com
Move the checks to decide whether a fastset is possible during the
initial commit to an encoder hook. This check is really encoder specific
and the next patch will also require this adding a DP encoder specific
check.
v2: Fix negated condition in gen11_dsi_initial_fastset_check().
v3: Make sure to call the hook for all encoders on the crtc. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201005215311.1475666-1-imre.deak@intel.com
On HP 800 G4 DM, if HDMI cable isn't plugged before boot, the HDMI port
becomes useless and never responds to cable hotplugging:
[ 3.031904] [drm:lspcon_init [i915]] *ERROR* Failed to probe lspcon
[ 3.031945] [drm:intel_ddi_init [i915]] *ERROR* LSPCON init failed on port D
Seems like the lspcon chip on the system only gets powered after the
cable is plugged.
Consilidate lspcon_init() into lspcon_resume() to dynamically init
lspcon chip, and make HDMI port work.
v6:
- Rebase on latest for-linux-next.
v5:
- Consolidate lspcon_resume() with lspcon_init().
- Move more logic into lspcon code.
v4:
- Trust VBT in intel_infoframe_init().
- Init lspcon in intel_dp_detect().
v3:
- Make sure it's handled under long HPD case.
v2:
- Move lspcon_init() inside of intel_dp_hpd_pulse().
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/203
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200610075542.12882-1-kai.heng.feng@canonical.com
Now that we've plumbed the crtc state all the way down we can
eliminate the DP_TP_{CTL,STATUS} register offsets from intel_dp,
and instead we derive them directly from the crtc state.
And thus we can get rid of the nasty hack in intel_ddi_get_config()
which mutates intel_dp during the readout.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200929233449.32323-12-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Get rid of mode crtc->config usage, and some ad-hoc intel_dp state
usage by plumbing the crtc state all the way down to the link training
code.
Unfortunately we do have to keep some cached state in intel_dp so
that we can do the "does the link need retraining?" checks from
the short hpd handler.
v2: Add intel_crtc_state forward declaration
v3: Don't kill the PHY test code totally since it's
now in the hotplug work where we can get at the states
v4: Don't resurrect the debug scrambling disable bit (Imre)
Use intel_dp_mst_is_master_trans() (Imre)
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201001111053.24451-1-ville.syrjala@linux.intel.com
The HDMI vs. not-HDMI check got inverted whem the bogus encoder->type
checks were eliminated. So now we're using 0 as the link rate on DP
and potentially non-zero on HDMI, which is exactly the opposite of
what we want. The original bogus check actually worked more correctly
by accident since if would always evaluate to true. Due to this we
now always use the RBR/HBR1 vswing table and never ever the HBR2+
vswing table. That is probably not a good way to get a high quality
signal at HBR2+ rates. Fix the check so we pick the right table.
Cc: stable@vger.kernel.org
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Fixes: 94641eb6c6 ("drm/i915/display: Fix the encoder type check")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200930223642.28565-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
DP 1.3 adds some extra control knobs for DP->HDMI protocol conversion.
Let's use that to configure the "HDMI mode" (ie. infoframes vs. not)
based on the capabilities of the sink.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200904115354.25336-13-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Non-HDMI sinks shouldn't be sent infoframes. Check for that when
using LSPCON.
FIXME: How do we turn off infoframes once enabled? Do we even
have to?
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200904115354.25336-3-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make a clean split between hpd pins for DDI vs. TC. This matches
how the actual hardware is split.
And with this we move the DDI/PHY->HPD pin mapping into the encoder
init instead of having to remap yet again in the interrupt code.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200630215601.28557-11-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Currently DP/HDMI/DDI encoders init their hpd_pin from the
connector init. Let's move it to the encoder init so that
we don't need to add platform specific junk to the connector
init (which is shared by all g4x+ platforms).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200630215601.28557-10-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl9VerweHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGhc4H/iHD6qLdB36gZB6K
oc2nJyrqyWitv4ti2Mnt5PA7o4wX4l6nnr1QvoaJ4BRs5Ja1czRvb2XDmdzqAoIA
xITGoafqaAeDfxQ91bWrJsVN0pCRKiGwddXlU7TWmqw/riAkfOqi6GYKvav4biJH
+n1mUPQb1M2IbRFsqkAS+ebKHq3CWaRvzKOEneS88nGlL5u31S9NAru8Ru/fkxRn
6CwGcs1XRaBPYaZAhdfIb0NuatUlpkhPC9yhNS9up6SqrWmK3m65vmFVng6H0eCF
fwn1jVztboY/XcNAi5sM9ExpQCql6WLQEEktVikqRDojC8fVtSx6W55tPt7qeaoO
Z6t4/DA=
=bcA4
-----END PGP SIGNATURE-----
Merge tag 'v5.9-rc4' into drm-next
Backmerge 5.9-rc4 as there is a nasty qxl conflict
that needs to be resolved.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reusing icl_get_combo_buf_trans() for eDP was causing the wrong table
being used when the eDP port don't support low power voltage swing table.
v2: Only use icl_combo_phy_ddi_translations_edp_hbr3 if low_vswing is
set as EHL combo phy supports HBR3 (Matt R)
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Cc: Lee Shawn C <shawn.c.lee@intel.com>
Cc: Khaled Almahallawy <khaled.almahallawy@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200826201549.83658-2-jose.souza@intel.com
Reusing icl_get_combo_buf_trans() for eDP was causing the wrong table
being used when the eDP port don't support low power voltage swing table.
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Cc: Lee Shawn C <shawn.c.lee@intel.com>
Cc: Khaled Almahallawy <khaled.almahallawy@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200826201549.83658-1-jose.souza@intel.com
This new HBR2 table for TGL-U and TGL-Y is required to pass
DisplayPort compliance.
BSpec: 49291
Cc: Khaled Almahallawy <khaled.almahallawy@intel.com>
Reviewed-by: Khaled Almahallawy<khaled.almahallawy@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200807192629.64134-2-jose.souza@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
If HTI (also sometimes called HDPORT) is enabled at startup, it may be
using some of the PHYs and DPLLs making them unavailable for general
usage. Let's read out the HDPORT_STATE register and avoid making use of
resources that HTI is already using.
v2:
- Fix minor checkpatch warnings
v3:
- Just readout HDPORT_STATE register once during init and then parse it
later as needed.
- Add a 'has_hti' device info flag to track whether we should readout
HDPORT_STATE or not. We can skip the platform/flag tests later since
the hti_state in dev_priv will remain 0 for platforms it does not
apply to.
- Move PLL masking into icl_get_combo_phy_dpll() since at the moment
RKL is the only platform that has HTI. (Jose)
Bspec: 49189
Bspec: 53707
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716220551.2730644-5-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Hours Of Battery Life is a new GEN12+ power-saving feature that allows
supported motherboards to use a special voltage swing table for eDP
panels that uses less power.
So here if supported by HW, OEM will set it in VBT and i915 will try
to train link with HOBL vswing table if link training fails it fall
back to the original table.
intel_ddi_dp_preemph_max() was optimized to only check the HOBL flag
instead of do something like is done in intel_ddi_dp_voltage_max()
because it is only called after the first entry of the voltage swing
table was loaded so the HOBL flag is valid at that point.
v3:
- removed a few parameters of icl_ddi_combo_vswing_program() that
can be taken from encoder
v4:
- using the HOBL vswing table until training fails completely (Ville)
v5:
- not reducing lane or link rate when link training fails with HOBL
active
- duplicated the HOBL voltage swing entry to match DP spec requirement
v6:
- removed the optional VS 3 & pre-emp 0 from HOBL table
- changed from u8:1 to bool to store hobl_failed/active
BSpec: 49291
BSpec: 49399
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200715175637.33763-1-jose.souza@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The value we program to DDI_BUF_CTL changes at the following places:
- At enabling/disabling the output to configure the port width etc, and
to enable/disable the DDI BUF function.
- At the beginning/end of link re-training to disable/re-enable the DDI
BUF function.
- On HSW/BDW/SKL to change the voltage swing/pre-emph levels.
Except of the above the value we program to the DDI_BUF_CTL register
(intel_dp->DP) doesn't change, so no need to reprogram the register when
changing the link training patterns (which is programmed via the
DP_TP_CTL register on DDI platforms).
v2:
- Fix the commit message wrt. voltage/pre-emph level values in
intel_dp->DP. (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200714153141.10280-2-imre.deak@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
According to BSpec this flag should not be changed while the DDI
function is enabled. On BDW+ the DP_TP_CTL register spec also states it
explicitly that the HW takes care of enabling/disabling the scrambling
for training patterns (and it must stay enabled for normal pixel
output). Assume that this HW automatic handling of scrambling is also
true for HSW.
BSpec: 8013, 7557, 50484
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200714153141.10280-1-imre.deak@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Based on the platform, Bspec expects us to wait or poll with
timeout for DDI BUF IDLE bit to be set to 0 (non idle) or get active
after enabling DDI_BUF_CTL.
v2:
* Based on platform, fixed delay or poll (Ville)
* Use a helper to do this (Imre, Ville)
v3:
* Add a new function _active for DDI BUF CTL to be non idle (Ville)
v4:
* Use the timeout for GLK (Ville)
v5:
* Add bspec quote, change timeout to 500us (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200701221052.8946-2-manasi.d.navare@intel.com
Modify the helper to add a fixed delay or poll with timeout
based on platform specification to check for either Idle bit
set (DDI_BUF_CTL is idle for disable case)
v2:
* Use 2 separate functions or idle and active (Ville)
v3:
* Change the timeout to 16usecs (Ville)
v4:
* Change the timeout 8, follow spec (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200701221052.8946-1-manasi.d.navare@intel.com
We have a mix of dport, intel_dport, intel_dig_port and dig_port to
reference a intel_digital_port struct. Numbers are around
5 intel_dport
36 dport
479 intel_dig_port
352 dig_port
Since we already removed the intel_ prefix from most of our other
structs, do the same here and prefer dig_port.
v2: rename everything in i915, not just a few display sources and
reword commit message (from Matt Roper)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200701045054.23357-1-lucas.demarchi@intel.com
The spec requires enabling the MST Virtual Channel payload allocation
- in a separate step - after the transcoder is enabled, follow this.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200623082411.3889-1-imre.deak@intel.com
MST encoders must use the master MST transcoder's DP_TP_STATUS and
DP_TP_CONTROL registers. Atm, during the HW readout of an MST encoder
connected to a slave transcoder we reset these register addresses in
intel_dp::regs.dp_tp_* to the slave transcoder's DP_TP_* register
addresses incorrectly; fix this.
One example where the above overwite happens is the encoder HW state
validation after enabling multiple streams; see
intel_dp_mst_enc_get_config(). After that during disabling any stream
we'll get a
'Timed out waiting for ACT sent when disabling'
error, due to reading from the incorrect DP_TP_STATUS register.
This change replaces
https://patchwork.freedesktop.org/patch/369577/?series=78193&rev=1
which just papered over the problem.
v2:
- Correct the failure scenario in the commit log. (José)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200616211146.23027-1-imre.deak@intel.com
For all ddi, encoder->type holds output type as ddi,
assigning it to individual o/p types is no more valid.
Fixes: 362bfb995b ("drm/i915/tgl: Add DKL PHY vswing table for HDMI")
v2: Rebase, no functional change.
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200612082237.11886-1-vandita.kulkarni@intel.com
According to BSpec the Data Island Packet should be disabled after
disabling the transcoder, but before the transcoder clock select is set
to none. On an ICL RVP, daisy-chained MST config not following this
leads to a hang with the following MCE when disabling the output:
[ 870.948739] mce: [Hardware Error]: CPU 0: Machine Check Exception: 5 Bank 6: ba00000011000402
[ 871.019212] mce: [Hardware Error]: RIP !INEXACT! 10:<ffffffff81aca652> {poll_idle+0x92/0xb0}
[ 871.019212] mce: [Hardware Error]: TSC 135a261fe61
[ 871.019212] mce: [Hardware Error]: PROCESSOR 0:706e5 TIME 1591739604 SOCKET 0 APIC 0 microcode 20
[ 871.019212] mce: [Hardware Error]: Run the above through 'mcelog --ascii'
[ 871.019212] mce: [Hardware Error]: Machine check: Processor context corrupt
[ 871.019212] Kernel panic - not syncing: Fatal machine check
[ 871.019212] Kernel Offset: disabled
Bspec: 4287
Fixes: fa37a21327 ("drm/i915: Stop sending DP SDPs on ddi disable")
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200609220616.6015-1-imre.deak@intel.com
As latest update we have now 2 voltage swing tables for DP over DKL
PHY with only one difference in Level 0 pre-emphasis 3.
So with 2 tables for DP is time to have one single function to return
all DKL voltage swing tables.
BSpec: 49292
Cc: Khaled Almahallawy <khaled.almahallawy@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Tested-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Reviewed-by: Khaled Almahallawy<khaled.almahallawy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200602205424.138143-1-jose.souza@intel.com
Cometlake is a small refresh of Coffeelake, but since we have found out a
difference in the plaforms, we need to identify them as separate platforms.
Since we previously took Coffeelake/Cometlake as identical, update all
IS_COFFEELAKE() to also include IS_COMETLAKE().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200602140541.5481-1-chris@chris-wilson.co.uk
In order to use a common VSC SDP Colorimetry calculating code on PSR,
it uses a new psr vsc sdp compute routine.
Because PSR routine has its own scenario and timings of writing a VSC SDP,
the current PSR routine needs to have its own drm_dp_vsc_sdp structure
member variable on struct i915_psr.
In order to calculate colorimetry information, intel_psr_update()
function and intel_psr_enable() function extend a drm_connector_state
argument.
There are no changes to PSR mechanism.
v3: Replace a structure name to drm_dp_vsc_sdp from intel_dp_vsc_sdp
v4: Rebased
v8: Rebased
v10: When a PSR is enabled, it needs to add DP_SDP_VSC to
infoframes.enable.
It is needed for comparing between HW and pipe_state of VSC_SDP.
v11: If PSR is disabled by flag, it don't enable psr on pipe compute.
v12: Fix an inconsistent indenting
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-15-gwan-gyeong.mun@intel.com
Call intel_dp_set_infoframes(false) function on intel_ddi_post_disable_dp()
to make sure not to send VSC SDP and HDR Metadata Infoframe SDP.
v5: Polish commit message [Uma]
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-13-gwan-gyeong.mun@intel.com
Call intel_dp_set_infoframes() function on pipe updates to make sure
that we send VSC SDP and HDR Metadata Infoframe SDP (when applicable)
on fastsets.
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-12-gwan-gyeong.mun@intel.com
Added state readout for DP VSC SDP and enabled state validation
for DP VSC SDP.
v2: Minor style fix
v3: Replace a structure name to drm_dp_vsc_sdp from intel_dp_vsc_sdp
v4: Use struct drm_device logging macros
v10: Skip checking of VSC SDP when a crtc config has psr.
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-10-gwan-gyeong.mun@intel.com
In order to use computed config for DP SDPs (DP VSC SDP and DP HDR Metadata
Infoframe SDP), it replaces intel_dp_vsc_enable() function and
intel_dp_hdr_metadata_enable() function to intel_dp_set_infoframes()
function.
And it removes unused functions.
Before:
intel_dp_vsc_enable() and intel_dp_hdr_metadata_enable() compute sdp
configs and program sdp registers on enable callback of encoder.
After:
It separates computing of sdp configs and programming of sdp register.
The compute config callback of encoder calls computing sdp configs.
The enable callback of encoder calls programming sdp register.
v3: Rebased
v5: Polish commit message [Uma]
v10: Rebased
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-8-gwan-gyeong.mun@intel.com
Get rid of several platform specific variants of
intel_digital_port_connected() and just use the ISR bits we've
stashed away.
v2: Duplicate stuff to avoid exposing platform specific
functions across files (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200311155422.3043-4-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Let's get rid of the platform if ladders in
intel_digital_port_connected() and make it a vfunc. Now the if
ladders are at the encoder initialization which makes them a bit
less convoluted.
v2: Add forward decl for intel_encoder in intel_tc.h
v3: Duplicate stuff to avoid exposing platform specific
functions across files (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200311155422.3043-2-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
