From: Steve Hodgson <shodgson@solarflare.com>
Commit 357d46a17e "sfc: QT202x: Remove
unreliable MMD check at initialisation" broke initialisation of the
SFE4002. efx_mdio_reset_mmd() returns a positive value rather than 0
on success. The above commit causes this value to be propagated up
by qt202x_reset_phy(), which is treated as a failure by its callers.
Change qt202x_reset_phy() to return 0 if successful.
The PCI layer treats >0 as "fail, but please call remove() anyway",
which means that unloading the driver would cause a crash. Add a
WARN_ON() on the failure path of efx_pci_probe() to provide early
warning if there are any other cases where we do this.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The low-level MCDI code always uses 32-bit MMIO operations, and
callers must pad input and output buffers to multiples of 4 bytes.
The MCDI NVRAM functions are not doing this. Also, their buffers are
declared as variable-length arrays with no explicit maximum length.
Switch to a fixed buffer size based on the chunk size used by the
MTD driver (which is a multiple of 4).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to a hardware bug in the SFC9000 family, the firmware must
transfer raw GMAC statistics to host memory before aggregating them
into the cooked (speed-independent) MAC statistics. Extend the stats
buffer to support this.
The length of the buffer is explicit in the MAC_STATS command, so this
change is backward-compatible on both sides.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Checking the PHY XS MMD here is unnecessary and can give false negatives.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO self-test should not be run on boards without an MDIO PHY,
such as SFN5122F-R3 and later revisions. It should also not try to
address a specific MMD in an MDIO clause 22 PHY. Check the
mode_support field to decide which mode to use, if any.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the interface is down and we are using polled mode for MCDI
operations, we busy-wait for completion for approximately 1 jiffy
using udelay() and then back off to schedule(). But the completion
will not wake the task, since we are using polled mode! We must use
schedule_timeout_uninterruptible() instead.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This hardware watchdog can misfire, so it does more harm than good.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some cables have EEPROMs that conflict with the PHY's on-board EEPROM
so it cannot load firmware.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY's firmware very occasionally appears to lock up very early, but
with the heartbeat update still running. Rebooting the microcontroller
core seems to be sufficient to recover.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY boots in a mode which is not necessarily optimal. This change
switches it to self-configure mode (except when in loopback, which
won't work in that mode if an SFP+ module is not present) by rebooting
the PHY's microcontroller, and replicating the sequence of configuration
writes from the boot EEPROM with the appropriate changes.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we see the PHY remaining stuck in a link-down state due to PCS being
down while PMA/PMD is up, we briefly switch to PMA/PMD loopback and back,
which usually unsticks it.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need buffer->len to remain valid to work out the correct address to
be unmapped. We therefore need to clear buffer->len after the unmap
operation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The XGXS block may not get a link immediately in XGXS or XAUI loopback
modes, so we still need to check it. Split falcon_xaui_link_ok() into
falcon_xgxs_link_ok(), which checks only the Falcon XGXS block, and
falcon_xmac_link_ok(), which checks one or both sides of the link as
appropriate. Also rename falcon_check_xaui_link() to
falcon_xmac_link_ok_retry().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This prevents efx->link_advertising from being blatted during
a reset.
The phy_short_reach sysfs node is now destroyed later in the
port shutdown process, so check for STATE_RUNNING after
acquiring the rtnl_lock (just like in set_phy_flash_cfg).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function efx_iterate_state contains the code
memcpy(&payload->msg, payload_msg, sizeof(payload_msg));
This is the only use of payload_msg. The type of payload_msg is
changed from a pointer to an array, so that the result of sizeof really is
the length of the string.
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression *x;
expression f;
type T;
@@
*f(...,(T)x,...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver has been mostly rewritten since Michael Brown's initial
work, so swap the order of the authors.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This integrates support for the SFC9000 family of 10G Ethernet
controllers and LAN-on-motherboard chips, starting with the SFL9021
'Siena' and SFC9020 'Bethpage'.
Credit for this code is largely due to my colleagues at Solarflare:
Guido Barzini
Steve Hodgson
Kieran Mansley
Matthew Slattery
Neil Turton
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the SFC9000 family of 10G Ethernet controllers
and LAN-on-motherboard chips, starting with the SFL9021 'Siena' and
SFC9020 'Bethpage'.
The SFC9000 family is based on the SFC4000 'Falcon' architecture, but
with some significant changes:
- Two ports are associated with two independent PCI functions
(except SFC9010)
- Integrated 10GBASE-T PHY(s) (SFL9021/9022)
- MAC, PHY and board peripherals are managed by firmware
- Driver does not require board-specific code
- Firmware supports wake-on-LAN and lights-out management through NC-SI
- IPv6 checksum offload and RSS
- Filtering by MAC address and VLAN (not included in this code)
- PCI SR-IOV (not included in this code)
Credit for this code is largely due to my colleagues at Solarflare:
Guido Barzini
Steve Hodgson
Kieran Mansley
Matthew Slattery
Neil Turton
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In new NICs flash is managed by firmware and we will use high-level
operations on partitions rather than direct SPI commands. Add support
for multiple MTD partitions per flash device and remove the direct
link between MTD and SPI devices. Maintain a list of MTD partitions
in struct efx_nic.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New NICs have firmware managing the PHY, and we will discover the PHY
capabilities at run-time. Replace the static data with probe() and
test_name() operations.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New NICs and PHYs support a wider variety of loopback modes.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
falcon_probe_nic_variant() does a lot less than it used to, and a
lot less than it claims to. Fold the remainder into its caller.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor efx_reset_down() and efx_reset_up() accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wake-on-LAN is a stub for Falcon, but will be implemented fully for
new NICs.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the efx_nic_type::monitor operation or event handling as
appropriate.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor PHY, MAC and NIC configuration operations so that the
existing link configuration can be re-pushed with:
efx->phy_op->reconfigure(efx);
efx->mac_op->reconfigure(efx);
and a new configuration with:
efx->nic_op->reconfigure_port(efx);
(plus locking and error-checking).
We have not held the link settings in software (aside from flow
control), and have relied on asking the hardware what they are. This
is a problem because in some cases the hardware may no longer be in a
state to tell us. In particular, if an entire multi-port board is
reset through one port, the driver bindings to other ports have no
chance to save settings before recovering.
We only actually need to keep track of the autonegotiation settings,
so add an ethtool advertising mask to struct efx_nic, initialise it
in PHY init and update it as necessary.
Remove now-unneeded uses of efx_phy_op::{get,set}_settings() and
struct ethtool_cmd.
Much of this was done by Steve Hodgson <shodgson@solarflare.com>.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is preparation for adding differing implementations for new NICs.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pause frame generation is gated by both RX_XOFF_MAC_EN and an enable
bit in each MAC. RX_XOFF_MAC_EN bit always reads back as 0 so we need
to set it correctly every time we modify RX_CFG_REG. Simplify this by
always setting it to 1 and only changing the enable bits in the MACs.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register only needs to be written after reset, not each time we
enable interrupts.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 'likely' hint to test of rx_checksum_enabled.
Don't count IP fragments; the IP stack can do that.
Do count non-matching multicast packets.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "bug9141 workaround" of setting TX_FLUSH_MIN_LEN_EN should really
be considered as a normal bit of configuration rather than a
workaround.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The strap bits are only important on Falcon A and all production
boards using it have fixed-speed 10G PHYs.
Replace dummy MAC operations with default MAC operations.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We never use MDIO in atomic context, so we don't need to spin.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reading standard registers on the QT2025C before its firmware has
booted may cause the boot process to fail. Therefore, follow the
recommended reset sequence before reading its id registers. Either
order works for the QT2022C2, so don't differentiate.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Falcon can generate events for LASI interrupts from the PHY, but in
practice we have never implemented this in reference designs. Instead
we have polled, inserted the appropriate events, and then handled the
events later. This is a waste of time and code.
Instead, make PHY poll functions update the link state synchronously
and report whether it changed. We can still make use of the LASI
registers as a shortcut on the SFT9001.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
