The code which does the chained handler setup was overwriting
chip_data.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Holger Hans Peter Freyther <holger@freyther.de>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
gUSA special cases r15 for part of its login/out sequence, meaning that
any parameters need to be explicitly prohibited from accidentally being
assigned that particular register, and the compiler ultimately needs to
use a temporary instead.
Certain configurations have begun generating code paths that do indeed
get allocated r15, resulting in immediate corruption of the exchanged
value. This was observed in (amongst others) exit_mm() code generation
where the xchg_u32 call was immediately corrupting a structure address.
As this is a general gUSA restriction, the rest of the users likewise
need to be updated to ensure sensible constraints.
References: https://bugzilla.stlinux.com/show_bug.cgi?id=11229
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Reviewed-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add the 'sync_super' function pointer to MD array structure (struct mddev_s)
If device-mapper (dm-raid.c) is to define its own on-disk superblock and be
able to load it, there must still be a way for MD to initiate superblock
updates. The simplest way to make this happen is to provide a pointer in
the MD array structure that can be set by device-mapper (or other module)
with a function to do this. If the function has been set, it will be used;
otherwise, the method with be looked up via 'super_types' as usual.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
MD RAID1: Changes to allow RAID1 to be used by device-mapper (dm-raid.c)
Added the necessary congestion function and conditionalize calls requiring an
array 'queue' or 'gendisk'.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Move personality and sync/recovery thread starting outside md_run.
Moving the wakeup's of the personality and sync/recovery threads out of
md_run and into do_md_run and mddev_resume solves two issues:
1) It allows bitmap_load to be called before the sync_thread is run and
2) when MD personalities are used by device-mapper (dm-raid.c), the start-up
of the array is better alligned with device-mapper primatives
(CTR/resume/suspend/DTR). I/O - in this case, recovery operations - should
not happen until after a resume has taken place.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Make message a bit clearer by s/blocks/k/
I chose 'k' vs 'kiB' or 'kB' because it is what is used earlier in the
message. 'k' may be a bit ambigous, but I think it's better than "blocks"
which normally means 512, but means 1024 in MD.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Disallow resync I/O while the RAID array is suspended.
Recovery, resync, and metadata I/O should not be allowed while a device is
suspended.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Don't attempt md_integrity_register if there is no gendisk struct available.
When MD arrays are built via device-mapper, the gendisk structure is not
available via mddev.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
If we request a lock and then abort (e.g., ^C), we need to send a matching
unlock request to the MDS to unwind our lock attempt to avoid indefinitely
blocking other clients.
Reported-by: Brian Chrisman <brchrisman@gmail.com>
Signed-off-by: Sage Weil <sage@newdream.net>
Getting ENOENT is equivalent to reading 0 bytes. Make that correction
before setting up the hit_stripe and was_short flags.
Fixes the following case:
dd if=/dev/zero of=/mnt/fs_depot/dd3 bs=1 seek=1048576 count=0
dd if=/mnt/fs_depot/dd3 of=/root/ddout1 skip=8 bs=500 count=2 iflag=direct
Reported-by: Henry C Chang <henry.cy.chang@gmail.com>
Signed-off-by: Sage Weil <sage@newdream.net>
If we get a short read from the OSD because the object is small, we need to
zero the remainder of the buffer. For O_DIRECT reads, the attempted range
is not trimmed to i_size by the VFS, so we were actually looping
indefinitely.
Fix by trimming by i_size, and the unconditionally zeroing the trailing
range.
Reported-by: Jeff Wu <cpwu@tnsoft.com.cn>
Signed-off-by: Sage Weil <sage@newdream.net>
If we cancel a write, trigger the safe completions to prevent a sync from
blocking indefinitely in ceph_osdc_sync().
Signed-off-by: Sage Weil <sage@newdream.net>
We should use ihold whenever we already have a stable inode ref, even
when we aren't holding i_lock. This avoids adding new and unnecessary
locking dependencies.
Signed-off-by: Sage Weil <sage@newdream.net>
We may write 4 byte too much when we reinitialize the anti replay
window in the replay advance functions. This patch fixes this by
adjusting the last index of the initialization loop.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/amd-iommu: Fix boot crash with hidden PCI devices
x86/amd-iommu: Use only per-device dma_ops
x86/amd-iommu: Fix 3 possible endless loops
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/nv40: fall back to paged dma object for the moment
drm/nouveau: fix leak of gart mm node
drm/nouveau: fix vram page mapping when crossing page table boundaries
drm/nv17-nv40: Fix modesetting failure when pitch == 4096px (fdo bug 35901).
drm/nouveau: don't create accel engine objects when noaccel=1
drm/nvc0: recognise 0xdX chipsets as NV_C0
drm/i915: Add a no lvds quirk for the Asus EeeBox PC EB1007
drm/i915: Share the common force-audio property between connectors
drm/i915: Remove unused enum "chip_family"
drm/915: fix relaxed tiling on gen2: tile height
drm/i915/crt: Explicitly return false if connected to a digital monitor
drm/i915: Replace ironlake_compute_wm0 with g4x_compute_wm0
drm/i915: Only print out the actual number of fences for i915_error_state
drm/i915: s/addr & ~PAGE_MASK/offset_in_page(addr)/
drm: i915: correct return status in intel_hdmi_mode_valid()
drm/i915: fix regression after clock gating init split
drm/i915: fix if statement in ivybridge irq handler
* 'drm-radeon-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms/atom: fix PHY init
drm/radeon/kms: add missing Evergreen texture formats to the CS parser
drm/radeon/kms: viewport height has to be even
drm/radeon/kms: remove duplicate reg from r600 safe regs
drm/radeon/kms: add support for Llano Fusion APUs
drm/radeon/kms: add llano pci ids
drm/radeon/kms: fill in asic struct for llano
drm/radeon/kms: add family ids for llano APUs
drm/radeon: fix oops in ttm reserve when pageflipping (v2)
drm/radeon/kms: clean up the radeon kms Kconfig
drm/radeon/kms: fix thermal sensor reading on juniper
drm/radeon/kms: add missing case for cayman thermal sensor
drm/radeon/kms: add blit support for cayman (v2)
drm/radeon/kms/blit: workaround some hw issues on evergreen+
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
timers: Consider slack value in mod_timer()
clockevents: Handle empty cpumask gracefully
* 'kvm-updates/3.0' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: Initialize kvm before registering the mmu notifier
KVM: x86: use proper port value when checking io instruction permission
KVM: add missing void __user * cast to access_ok() call
We had to say goodbye when David passed away recently. David had a
huge impact on our community, both personally in the lives of the
people he worked with, and technically in the design and maintenance
of several subsystems. He is greatly missed.
He also leaves behind a number of much loved subsystems now orphaned.
This patch updates the MAINTAINERS file for the areas that David was
responsible for and adds an entry for him to the CREDITS file.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Harry Wei <harryxiyou@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
_sdata needs to be declared in the linker script now as of commit
a2d063ac21 ("extable, core_kernel_data(): Make sure all archs define
_sdata")
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
die_if_no_fixup() shouldn't use get_user() as it doesn't call set_fs() to
indicate that it wants to probe a kernel address. Instead it should use
probe_kernel_read().
This fixes the problem of gdb seeing SIGILL rather than SIGTRAP when hitting
the KGDB special breakpoint upon SysRq+g being seen. The problem was that
die_if_no_fixup() was failing to read the opcode of the instruction that caused
the exception, and thus not fixing up the exception.
This caused gdb to get a S04 response to the $? request in its remote protocol
rather than S05 - which would then cause it to continue with $C04 rather than
$c in an attempt to pass the signal onto the inferior process. The kernel,
however, does not support $Cnn, and so objects by returning an E22 response,
indicating an error. gdb does not expect this and prints:
warning: Remote failure reply: E22
and then returns to the gdb command prompt unable to continue.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
One of the kernel debugger cacheflush variants escaped proper testing. Two of
the labels are wrong, being derived from the code that was copied to construct
the variant.
The first label results in the following assembler message:
AS arch/mn10300/mm/cache-dbg-flush-by-reg.o
arch/mn10300/mm/cache-dbg-flush-by-reg.S: Assembler messages:
arch/mn10300/mm/cache-dbg-flush-by-reg.S:123: Error: symbol `debugger_local_cache_flushinv_no_dcache' is already defined
And the second label results in the following linker message:
arch/mn10300/mm/built-in.o:(.text+0x1d39): undefined reference to `mn10300_local_icache_inv_range_reg_end'
arch/mn10300/mm/built-in.o:(.text+0x1d39): relocation truncated to fit: R_MN10300_PCREL16 against undefined symbol `mn10300_local_icache_inv_range_reg_end'
To test this file the following configuration pieces must be set:
CONFIG_AM34=y
CONFIG_MN10300_CACHE_WBACK=y
CONFIG_MN10300_DEBUGGER_CACHE_FLUSH_BY_REG=y
CONFIG_MN10300_CACHE_MANAGE_BY_REG=y
CONFIG_AM34_HAS_CACHE_SNOOP=n
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (21 commits)
ARM: OMAP4: MMC: increase delay for pbias
arm: omap2plus: move NAND_BLOCK_SIZE out of boards
omap4: hwmod: Enable the keypad
omap3: Free Beagle rev gpios when they are read, so others can read them later
arm: omap3: beagle: Ensure msecure is mux'd to be able to set the RTC
omap: rx51: Don't power up speaker amplifier at bootup
omap: rx51: Set regulator V28_A always on
ARM: OMAP4: MMC: no regulator off during probe for eMMC
arm: omap2plus: fix ads7846 pendown gpio request
ARM: OMAP2: Add missing iounmap in omap4430_phy_init
ARM: omap4: Pass core and wakeup mux tables to omap4_mux_init
ARM: omap2+: mux: Allow board mux settings to be NULL
OMAP4: fix return value of omap4_l3_init
OMAP: iovmm: fix SW flags passed by user
arch/arm/mach-omap1/dma.c: Invert calls to platform_device_put and platform_device_del
OMAP2+: mux: fix compilation warnings
OMAP: SRAM: Fix warning: format '%08lx' expects type 'long unsigned int'
arm: omap3: cm-t3517: fix section mismatch warning
OMAP2+: Fix 9 section mismatch(es) warnings from mach-omap2/built-in.o
ARM: OMAP2: Add missing include of linux/gpio.h
...
* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
vfs: make unlink() and rmdir() return ENOENT in preference to EROFS
lmLogOpen() broken failure exit
usb: remove bad dput after dentry_unhash
more conservative S_NOSEC handling
Semicolons are not necessary after switch/while/for/if braces
so remove them.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some devices that can generate interrupts are connected directly to the
CPU through the bootbus on sun4d. This patch allows IRQs to be allocated
for such devices. The information used for allocating interrupts for
sbus devices are present at the corresponding SBI node. For bootbus
devices this information is present in the bootbus node.
Signed-off-by: Kjetil Oftedal <oftedal@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the introduction of genirq on sparc32 bugs were introduced in
the interrupt handler for sun4d. The interrupts handler checks the status
of the various sbus interfaces in the system and generates a virtual
interrupt, based upon the location of the interrupt source. This lookup
was broken by restructuring the code in such a way that index and shift
operations were performed prior to comparing this against the values
read from the interrupt controllers.
This could cause the handler to loop eternally as the interrupt source
could be skipped before any check was performed. Additionally
sun4d_encode_irq performs shifting internally, so it should not be performed
twice.
In sun4d_unmask interrupts were not correctly acknowledged, as the
corresponding bit it the interrupt mask was not actually cleared.
Signed-off-by: Kjetil Oftedal <oftedal@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sun4d_build_device_irq was called without a valid platform_device when
the system timer was initialized on sun4d systems. This caused a NULL
pointer crash.
Josip Rodin suggested that the current sun4d_build_device_irq should be
split into two functions. So that the timer initialization could skip
the slot and sbus interface detection code in sun4d_build_device_irq, as
this does not make sence due to the timer interrupts not being generated
from a device located on sbus.
Signed-off-by: Kjetil Oftedal <oftedal@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit a559d2c8c1.
Turns out that device id 0x1d6b:0x0002 is a USB hub, which causes havoc
when the option driver tries to bind to it.
So revert this as it doesn't seem to be needed at all.
Thanks to Michael Tokarev and Paweł Drobek for working on resolving this
issue.
Cc: Paweł Drobek <pawel.drobek@gmail.com>
Cc: Michael Tokarev <mjt@tls.msk.ru>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The loops over connection ID strings in pm_runtime_clk_notify()
should actually iterate over the strings and not over the elements
of the first of them, so make them behave as appropriate.
This fixes a regression introduced by commit 600b776eb3
(OMAP1 / PM: Use generic clock manipulation routines for runtime PM).
Reported-and-tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
When SR-IOV is enabled, i350 devices fail to pass traffic. This is due to
the driver attempting to enable RSS on the PF device, which is not
supported by the i350.
When max_vfs is specified on an i350 adapter, set the number of RSS queues
to 1.
This issue affects 2.6.39 as well.
CC: stable@kernel.org
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Samsung GPIO drivers are always built-in when the relevant
platform is selected. Change the Kconfig symbol to def_bool y
dependant on the platform.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
To work around controllers which can't properly plug events while
reset, ata_eh_reset() clears error states and ATA_PFLAG_EH_PENDING
after reset but before RESET is marked done. As reset is the final
recovery action and full verification of devices including onlineness
and classfication match is done afterwards, this shouldn't lead to
lost devices or missed hotplug events.
Unfortunately, it forgot to thaw the port when clearing EH_PENDING, so
if the condition happens after resetting an empty port, the port could
be left frozen and EH will end without thawing it, making the port
unresponsive to further hotplug events.
Thaw if the port is frozen after clearing EH_PENDING. This problem is
reported by Bruce Stenning in the following thread.
http://thread.gmane.org/gmane.linux.kernel/1123265
stable: I think we should weather this patch a bit longer in -rcX
before sending it to -stable. Please wait at least a month
after this patch makes upstream. Thanks.
-v2: Fixed spelling in the comment per Dave Howorth.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Bruce Stenning <b.stenning@indigovision.com>
Cc: stable@kernel.org
Cc: Dave Howorth <dhoworth@mrc-lmb.cam.ac.uk>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
If CONFIG_PM is not set, init_iommu_pm_ops() introduced by commit
134fac3f45 (PCI / Intel IOMMU: Use
syscore_ops instead of sysdev class and sysdev) is not defined
appropriately. Fix this issue.
Reported-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The data pointer should be freed in the error
cases of adis16400_trigger_handler().
Signed-off-by: Andre Bartke <andre.bartke@gmail.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Many Linux distributions would enable vesafb in order to display
early stage boot splash. In this case, we will get garbled X
Window screen if running X fbdev on psbfb.
This is because fb0 is occupied by vesafb while psbfb is on fb1.
They tried to drive the same pieces of hardware at the same
time. With unmodified X start-up, it would try to use default
fb0 framebuffer device and unfortunately it is now broken
becaues fb1 supersedes it.
We should let psbfb takeover framebuffer control from vesafb
to get around this problem.
See also commit : 4410f39109
Signed-off-by: Michael Chang <mchang@novell.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On the Fit-PC2 the VBT reports an invalid fixed panel mode for LVDS, this gets
in the way for SDVO. This patch makes VBT parsing skip the invalid mode. When
there is no LVDS output the backlight support crashes so the patch also checks
for this before enabling it.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Implemented pre_reset and post_reset methods of the driver to prevent the
driver from being unbound upon a device reset. Because of this also the
asynchronous reset introduced to prevent a race condition is no longer necessary
(and sometimes causes problems, because it comes later then expected).
Signed-off-by: Arjan Mels <arjan.mels@gmx.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Takahiro Hirofuchi <hirofuchi@users.sourceforge.net>
Cc: Max Vozeler <max@vozeler.com>
Cc: usbip-devel <usbip-devel@lists.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Failure to set iio_poll_func private_data, causes zero pointer access
violations in all consumer trigger handlers.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Looks like a typo.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix build errors when CONFIG_CFG80211 is not enabled:
drivers/built-in.o: In function `ar6k_cfg80211_deinit':
(.text+0x189b71): undefined reference to `cfg80211_scan_done'
drivers/built-in.o: In function `ar6k_cfg80211_deinit':
(.text+0x189b86): undefined reference to `wiphy_unregister'
drivers/built-in.o: In function `ar6k_cfg80211_deinit':
(.text+0x189b8d): undefined reference to `wiphy_free'
drivers/built-in.o: In function `ar6k_cfg80211_init':
(.text+0x18add7): undefined reference to `wiphy_new'
drivers/built-in.o: In function `ar6k_cfg80211_init':
(.text+0x18ae48): undefined reference to `wiphy_register'
drivers/built-in.o: In function `ar6k_cfg80211_tkip_micerr_event':
(.text+0x18ae95): undefined reference to `cfg80211_michael_mic_failure'
drivers/built-in.o: In function `ar6k_cfg80211_scan_node':
(.text+0x18afb5): undefined reference to `__ieee80211_get_channel'
drivers/built-in.o: In function `ar6k_cfg80211_scan_node':
(.text+0x18afd2): undefined reference to `cfg80211_inform_bss_frame'
drivers/built-in.o: In function `ar6k_cfg80211_disconnect_event':
(.text+0x18b046): undefined reference to `cfg80211_ibss_joined'
drivers/built-in.o: In function `ar6k_cfg80211_disconnect_event':
(.text+0x18b176): undefined reference to `cfg80211_connect_result'
drivers/built-in.o: In function `ar6k_cfg80211_disconnect_event':
(.text+0x18b190): undefined reference to `cfg80211_disconnected'
drivers/built-in.o: In function `ar6k_cfg80211_connect_event':
(.text+0x18b291): undefined reference to `cfg80211_get_bss'
drivers/built-in.o: In function `ar6k_cfg80211_connect_event':
(.text+0x18b457): undefined reference to `cfg80211_put_bss'
drivers/built-in.o: In function `ar6k_cfg80211_connect_event':
(.text+0x18b4fa): undefined reference to `cfg80211_roamed'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Cc: Joe Perches <joe@perches.com>
Cc: Naveen Singh <nsingh@atheros.com>
Signed-off-by: Peter Foley <pefoley2@verizon.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
