Check at start of fill_frame_info that the MAC header in the supplied
skb is large enough to fit a struct hsr_ethhdr, as otherwise this is
not a valid HSR frame. If it is too small, return an error which will
then cause the callers to clean up the skb. Fixes a KMSAN-found
uninit-value bug reported by syzbot at:
https://syzkaller.appspot.com/bug?id=f7e9b601f1414f814f7602a82b6619a8d80bce3f
Reported-by: syzbot+e267bed19bfc5478fb33@syzkaller.appspotmail.com
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reset MAC header in HSR Tx path. This is needed, because direct packet
transmission, e.g. by specifying PACKET_QDISC_BYPASS does not reset the MAC
header.
This has been observed using the following setup:
|$ ip link add name hsr0 type hsr slave1 lan0 slave2 lan1 supervision 45 version 1
|$ ifconfig hsr0 up
|$ ./test hsr0
The test binary is using mmap'ed sockets and is specifying the
PACKET_QDISC_BYPASS socket option.
This patch resolves the following warning on a non-patched kernel:
|[ 112.725394] ------------[ cut here ]------------
|[ 112.731418] WARNING: CPU: 1 PID: 257 at net/hsr/hsr_forward.c:560 hsr_forward_skb+0x484/0x568
|[ 112.739962] net/hsr/hsr_forward.c:560: Malformed frame (port_src hsr0)
The warning can be safely removed, because the other call sites of
hsr_forward_skb() make sure that the skb is prepared correctly.
Fixes: d346a3fae3 ("packet: introduce PACKET_QDISC_BYPASS socket option")
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A typo is found out by codespell tool in 111th line of hsr_debugfs.c:
$ codespell ./net/hsr/
net/hsr/hsr_debugfs.c:111: Debufs ==> Debugfs
Fix typos found by codespell.
Signed-off-by: Xiong Zhenwu <xiong.zhenwu@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
In IEC 62439-3 EntryForgetTime is defined with a value of 400 ms. When a
node does not send any frame within this time, the sequence number check
for can be ignored. This solves communication issues with Cisco IE 2000
in Redbox mode.
Fixes: f421436a59 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Marco Wenzel <marco.wenzel@a-eberle.de>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210224094653.1440-1-marco.wenzel@a-eberle.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for offloading of HSR/PRP (IEC 62439-3) tag insertion
tag removal, duplicate generation and forwarding.
For HSR, insertion involves the switch adding a 6 byte HSR header after
the 14 byte Ethernet header. For PRP it adds a 6 byte trailer.
Tag removal involves automatically stripping the HSR/PRP header/trailer
in the switch. This is possible when the switch also performs auto
deduplication using the HSR/PRP header/trailer (making it no longer
required).
Forwarding involves automatically forwarding between redundant ports in
an HSR. This is crucial because delay is accumulated as a frame passes
through each node in the ring.
Duplication involves the switch automatically sending a single frame
from the CPU port to both redundant ports. This is required because the
inserted HSR/PRP header/trailer must contain the same sequence number
on the frames sent out both redundant ports.
Export is_hsr_master so DSA can tell them apart from other devices in
dsa_slave_changeupper.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For a switch to offload insertion of HSR/PRP tags, frames must not be
sent to the CPU facing switch port with a tag. Generate supervision frames
(eth type ETH_P_PRP) without HSR v1 (ETH_P_HSR)/PRP tag and rely on
create_tagged_frame which inserts it later. This will allow skipping the
tag insertion for all outgoing frames in the future which is required for
HSR v1/PRP tag insertions to be offloaded.
HSR v0 supervision frames always contain tag information so insertion of
the tag can't be offloaded. IEC 62439-3 Ed.2.0 (HSR v1) specifically
notes that this was changed since v0 to allow offloading.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sup_multicast_addr is passed to ether_addr_equal for address comparison
which casts the address inputs to u16 leading to an unaligned access.
Aligning the sup_multicast_addr to u16 boundary fixes the issue.
Signed-off-by: Andreas Oetken <andreas.oetken@siemens.com>
Link: https://lore.kernel.org/r/20210202090304.2740471-1-ennoerlangen@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bulk of the genetlink users can use smaller ops, move them.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clean follow coccicheck warning:
net//hsr/hsr_netlink.c:94:8-42: WARNING avoid newline at end of message
in NL_SET_ERR_MSG_MOD
net//hsr/hsr_netlink.c:87:30-57: WARNING avoid newline at end of message
in NL_SET_ERR_MSG_MOD
net//hsr/hsr_netlink.c:79:29-53: WARNING avoid newline at end of message
in NL_SET_ERR_MSG_MOD
Signed-off-by: Ye Bin <yebin10@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to %pM instead of using custom code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print PRP specific information from node table as part of debugfs
node table display. Also display the node as DAN-H or DAN-P depending
on the info from node table.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DAN-P (Dual Attached Nodes PRP) nodes are expected to receive
traditional IP packets as well as PRP (Parallel Redundancy
Protocol) tagged (trailer) packets. PRP trailer is 6 bytes
of PRP protocol unit called RCT, Redundancy Control Trailer
(RCT) similar to HSR tag. PRP network can have traditional
devices such as bridges/switches or PC attached to it and
should be able to communicate. Regular Ethernet devices treat
the RCT as pads. This patch adds logic to format L2 frames
from network stack to add a trailer (RCT) and send it as
duplicates over the slave interfaces when the protocol is
PRP as per IEC 62439-3. At the ingress, it strips the trailer,
do duplicate detection and rejection and forward a stripped
frame up the network stack. PRP device should accept frames
from Singly Attached Nodes (SAN) and thus the driver mark
the link where the frame came from in the node table.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparatory patch to introduce PRP, refactor the code specific to
handling HSR frames into separate functions and call them through
proto_ops function pointers.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for generation of PRP supervision frames. For PRP,
supervision frame format is similar to HSR version 0, but have
a PRP Redundancy Control Trailer (RCT) added and uses a different
message type, PRP_TLV_LIFE_CHECK_DD. Also update
is_supervision_frame() to include the new message type used for
PRP supervision frame.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparatory patch to introduce support for PRP protocol, add a
protocol ops ptr in the private hsr structure to hold function
pointers as some of the functions at protocol level packet
handling is different for HSR vs PRP. It is expected that PRP will
add its of set of functions for protocol handling. Modify existing
hsr_announce() function to call proto_ops->send_sv_frame() to send
supervision frame for HSR. This is expected to be different for PRP.
So introduce a ops function ptr, send_sv_frame() for the same and
initialize it to send_hsr_supervsion_frame(). Modify hsr_announce()
to call proto_ops->send_sv_frame().
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparatory patch to introduce PRP protocol support in the
driver, refactor the skb init code to a separate function.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parallel Redundancy Protocol (PRP) is another redundancy protocol
introduced by IEC 63439 standard. It is similar to HSR in many
aspects:-
- Use a pair of Ethernet interfaces to created the PRP device
- Use a 6 byte redundancy protocol part (RCT, Redundancy Check
Trailer) similar to HSR Tag.
- Has Link Redundancy Entity (LRE) that works with RCT to implement
redundancy.
Key difference is that the protocol unit is a trailer instead of a
prefix as in HSR. That makes it inter-operable with tradition network
components such as bridges/switches which treat it as pad bytes,
whereas HSR nodes requires some kind of translators (Called redbox) to
talk to regular network devices. This features allows regular linux box
to be converted to a DAN-P box. DAN-P stands for Dual Attached Node - PRP
similar to DAN-H (Dual Attached Node - HSR).
Add a comment at the header/source code to explicitly state that the
driver files also handles PRP protocol as well.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP reuseport conflict was a little bit tricky.
The net-next code, via bpf-next, extracted the reuseport handling
into a helper so that the BPF sk lookup code could invoke it.
At the same time, the logic for reuseport handling of unconnected
sockets changed via commit efc6b6f6c3
which changed the logic to carry on the reuseport result into the
rest of the lookup loop if we do not return immediately.
This requires moving the reuseport_has_conns() logic into the callers.
While we are here, get rid of inline directives as they do not belong
in foo.c files.
The other changes were cases of more straightforward overlapping
modifications.
Signed-off-by: David S. Miller <davem@davemloft.net>
Because kfree_skb already checked NULL skb parameter,
so the additional checks are unnecessary, just remove them.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_put_padto() can fail. So check for return type and return NULL
for skb. Caller checks for skb and acts correctly if it is NULL.
Fixes: 6d6148bc78 ("net: hsr: fix incorrect lsdu size in the tag of HSR frames for small frames")
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Validate MAC address before copying the same to outgoing frame
skb destination address. Since a node can have zero mac
address for Link B until a valid frame is received over
that link, this fix address the issue of a zero MAC address
being in the packet.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For small Ethernet frames with size less than minimum size 66 for HSR
vs 60 for regular Ethernet frames, hsr driver currently doesn't pad the
frame to make it minimum size. This results in incorrect LSDU size being
populated in the HSR tag for these frames. Fix this by padding the frame
to the minimum size applicable for HSR.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.
Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an interface is being deleted, "/proc/net/dev_snmp6/<interface name>"
is deleted.
The function for this is addrconf_ifdown() in the addrconf_notify() and
it is called by notification, which is NETDEV_UNREGISTER.
But, if NETDEV_CHANGEMTU is triggered after NETDEV_UNREGISTER,
this proc file will be created again.
This recreated proc file will be deleted by netdev_wati_allrefs().
Before netdev_wait_allrefs() is called, creating a new HSR interface
routine can be executed and It tries to create a proc file but it will
find an un-deleted proc file.
At this point, it warns about it.
To avoid this situation, it can use ->dellink() instead of
->ndo_uninit() to release resources because ->dellink() is called
before NETDEV_UNREGISTER.
So, a proc file will not be recreated.
Test commands
ip link add dummy0 type dummy
ip link add dummy1 type dummy
ip link set dummy0 mtu 1300
#SHELL1
while :
do
ip link add hsr0 type hsr slave1 dummy0 slave2 dummy1
done
#SHELL2
while :
do
ip link del hsr0
done
Splat looks like:
[ 9888.980852][ T2752] proc_dir_entry 'dev_snmp6/hsr0' already registered
[ 9888.981797][ C2] WARNING: CPU: 2 PID: 2752 at fs/proc/generic.c:372 proc_register+0x2d5/0x430
[ 9888.981798][ C2] Modules linked in: hsr dummy veth openvswitch nsh nf_conncount nf_nat nf_conntrack nf_defrag_ipv6x
[ 9888.981814][ C2] CPU: 2 PID: 2752 Comm: ip Tainted: G W 5.8.0-rc1+ #616
[ 9888.981815][ C2] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 9888.981816][ C2] RIP: 0010:proc_register+0x2d5/0x430
[ 9888.981818][ C2] Code: fc ff df 48 89 fa 48 c1 ea 03 80 3c 02 00 0f 85 65 01 00 00 49 8b b5 e0 00 00 00 48 89 ea 40
[ 9888.981819][ C2] RSP: 0018:ffff8880628dedf0 EFLAGS: 00010286
[ 9888.981821][ C2] RAX: dffffc0000000008 RBX: ffff888028c69170 RCX: ffffffffaae09a62
[ 9888.981822][ C2] RDX: 0000000000000001 RSI: 0000000000000008 RDI: ffff88806c9f75ac
[ 9888.981823][ C2] RBP: ffff888028c693f4 R08: ffffed100d9401bd R09: ffffed100d9401bd
[ 9888.981824][ C2] R10: ffffffffaddf406f R11: 0000000000000001 R12: ffff888028c69308
[ 9888.981825][ C2] R13: ffff8880663584c8 R14: dffffc0000000000 R15: ffffed100518d27e
[ 9888.981827][ C2] FS: 00007f3876b3b0c0(0000) GS:ffff88806c800000(0000) knlGS:0000000000000000
[ 9888.981828][ C2] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 9888.981829][ C2] CR2: 00007f387601a8c0 CR3: 000000004101a002 CR4: 00000000000606e0
[ 9888.981830][ C2] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 9888.981831][ C2] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 9888.981832][ C2] Call Trace:
[ 9888.981833][ C2] ? snmp6_seq_show+0x180/0x180
[ 9888.981834][ C2] proc_create_single_data+0x7c/0xa0
[ 9888.981835][ C2] snmp6_register_dev+0xb0/0x130
[ 9888.981836][ C2] ipv6_add_dev+0x4b7/0xf60
[ 9888.981837][ C2] addrconf_notify+0x684/0x1ca0
[ 9888.981838][ C2] ? __mutex_unlock_slowpath+0xd0/0x670
[ 9888.981839][ C2] ? kasan_unpoison_shadow+0x30/0x40
[ 9888.981840][ C2] ? wait_for_completion+0x250/0x250
[ 9888.981841][ C2] ? inet6_ifinfo_notify+0x100/0x100
[ 9888.981842][ C2] ? dropmon_net_event+0x227/0x410
[ 9888.981843][ C2] ? notifier_call_chain+0x90/0x160
[ 9888.981844][ C2] ? inet6_ifinfo_notify+0x100/0x100
[ 9888.981845][ C2] notifier_call_chain+0x90/0x160
[ 9888.981846][ C2] register_netdevice+0xbe5/0x1070
[ ... ]
Reported-by: syzbot+1d51c8b74efa4c44adeb@syzkaller.appspotmail.com
Fixes: e0a4b99773 ("hsr: use upper/lower device infrastructure")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
When VLAN frame is being sent, hsr calls WARN_ONCE() because hsr doesn't
support VLAN. But using WARN_ONCE() is overdoing.
Using netdev_warn_once() is enough.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following sparse checker warning:-
net/hsr/hsr_slave.c:38:18: warning: incorrect type in assignment (different base types)
net/hsr/hsr_slave.c:38:18: expected unsigned short [unsigned] [usertype] protocol
net/hsr/hsr_slave.c:38:18: got restricted __be16 [usertype] h_proto
net/hsr/hsr_slave.c:39:25: warning: restricted __be16 degrades to integer
net/hsr/hsr_slave.c:39:57: warning: restricted __be16 degrades to integer
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When all hsr slave interfaces are removed, hsr interface doesn't work.
At that moment, it's fine to remove an unused hsr interface automatically
for saving resources.
That's a common behavior of virtual interfaces.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the hsr_dev_change_mtu(), the 'dev' and 'master->dev' pointer are
same. So, the 'master' variable and some code are unnecessary.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current hsr code, only 0 and 1 protocol versions are valid.
But current hsr code doesn't check the version, which is received by
userspace.
Test commands:
ip link add dummy0 type dummy
ip link add dummy1 type dummy
ip link add hsr0 type hsr slave1 dummy0 slave2 dummy1 version 4
In the test commands, version 4 is invalid.
So, the command should be failed.
After this patch, following error will occur.
"Error: hsr: Only versions 0..1 are supported."
Fixes: ee1c279772 ("net/hsr: Added support for HSR v1")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Overlapping header include additions in macsec.c
A bug fix in 'net' overlapping with the removal of 'version'
string in ena_netdev.c
Overlapping test additions in selftests Makefile
Overlapping PCI ID table adjustments in iwlwifi driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
The port->hsr is used in the hsr_handle_frame(), which is a
callback of rx_handler.
hsr master and slaves are initialized in hsr_add_port().
This function initializes several pointers, which includes port->hsr after
registering rx_handler.
So, in the rx_handler routine, un-initialized pointer would be used.
In order to fix this, pointers should be initialized before
registering rx_handler.
Test commands:
ip netns del left
ip netns del right
modprobe -rv veth
modprobe -rv hsr
killall ping
modprobe hsr
ip netns add left
ip netns add right
ip link add veth0 type veth peer name veth1
ip link add veth2 type veth peer name veth3
ip link add veth4 type veth peer name veth5
ip link set veth1 netns left
ip link set veth3 netns right
ip link set veth4 netns left
ip link set veth5 netns right
ip link set veth0 up
ip link set veth2 up
ip link set veth0 address fc:00:00:00:00:01
ip link set veth2 address fc:00:00:00:00:02
ip netns exec left ip link set veth1 up
ip netns exec left ip link set veth4 up
ip netns exec right ip link set veth3 up
ip netns exec right ip link set veth5 up
ip link add hsr0 type hsr slave1 veth0 slave2 veth2
ip a a 192.168.100.1/24 dev hsr0
ip link set hsr0 up
ip netns exec left ip link add hsr1 type hsr slave1 veth1 slave2 veth4
ip netns exec left ip a a 192.168.100.2/24 dev hsr1
ip netns exec left ip link set hsr1 up
ip netns exec left ip n a 192.168.100.1 dev hsr1 lladdr \
fc:00:00:00:00:01 nud permanent
ip netns exec left ip n r 192.168.100.1 dev hsr1 lladdr \
fc:00:00:00:00:01 nud permanent
for i in {1..100}
do
ip netns exec left ping 192.168.100.1 &
done
ip netns exec left hping3 192.168.100.1 -2 --flood &
ip netns exec right ip link add hsr2 type hsr slave1 veth3 slave2 veth5
ip netns exec right ip a a 192.168.100.3/24 dev hsr2
ip netns exec right ip link set hsr2 up
ip netns exec right ip n a 192.168.100.1 dev hsr2 lladdr \
fc:00:00:00:00:02 nud permanent
ip netns exec right ip n r 192.168.100.1 dev hsr2 lladdr \
fc:00:00:00:00:02 nud permanent
for i in {1..100}
do
ip netns exec right ping 192.168.100.1 &
done
ip netns exec right hping3 192.168.100.1 -2 --flood &
while :
do
ip link add hsr0 type hsr slave1 veth0 slave2 veth2
ip a a 192.168.100.1/24 dev hsr0
ip link set hsr0 up
ip link del hsr0
done
Splat looks like:
[ 120.954938][ C0] general protection fault, probably for non-canonical address 0xdffffc0000000006: 0000 [#1]I
[ 120.957761][ C0] KASAN: null-ptr-deref in range [0x0000000000000030-0x0000000000000037]
[ 120.959064][ C0] CPU: 0 PID: 1511 Comm: hping3 Not tainted 5.6.0-rc5+ #460
[ 120.960054][ C0] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 120.962261][ C0] RIP: 0010:hsr_addr_is_self+0x65/0x2a0 [hsr]
[ 120.963149][ C0] Code: 44 24 18 70 73 2f c0 48 c1 eb 03 48 8d 04 13 c7 00 f1 f1 f1 f1 c7 40 04 00 f2 f2 f2 4
[ 120.966277][ C0] RSP: 0018:ffff8880d9c09af0 EFLAGS: 00010206
[ 120.967293][ C0] RAX: 0000000000000006 RBX: 1ffff1101b38135f RCX: 0000000000000000
[ 120.968516][ C0] RDX: dffffc0000000000 RSI: ffff8880d17cb208 RDI: 0000000000000000
[ 120.969718][ C0] RBP: 0000000000000030 R08: ffffed101b3c0e3c R09: 0000000000000001
[ 120.972203][ C0] R10: 0000000000000001 R11: ffffed101b3c0e3b R12: 0000000000000000
[ 120.973379][ C0] R13: ffff8880aaf80100 R14: ffff8880aaf800f2 R15: ffff8880aaf80040
[ 120.974410][ C0] FS: 00007f58e693f740(0000) GS:ffff8880d9c00000(0000) knlGS:0000000000000000
[ 120.979794][ C0] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 120.980773][ C0] CR2: 00007ffcb8b38f29 CR3: 00000000afe8e001 CR4: 00000000000606f0
[ 120.981945][ C0] Call Trace:
[ 120.982411][ C0] <IRQ>
[ 120.982848][ C0] ? hsr_add_node+0x8c0/0x8c0 [hsr]
[ 120.983522][ C0] ? rcu_read_lock_held+0x90/0xa0
[ 120.984159][ C0] ? rcu_read_lock_sched_held+0xc0/0xc0
[ 120.984944][ C0] hsr_handle_frame+0x1db/0x4e0 [hsr]
[ 120.985597][ C0] ? hsr_nl_nodedown+0x2b0/0x2b0 [hsr]
[ 120.986289][ C0] __netif_receive_skb_core+0x6bf/0x3170
[ 120.992513][ C0] ? check_chain_key+0x236/0x5d0
[ 120.993223][ C0] ? do_xdp_generic+0x1460/0x1460
[ 120.993875][ C0] ? register_lock_class+0x14d0/0x14d0
[ 120.994609][ C0] ? __netif_receive_skb_one_core+0x8d/0x160
[ 120.995377][ C0] __netif_receive_skb_one_core+0x8d/0x160
[ 120.996204][ C0] ? __netif_receive_skb_core+0x3170/0x3170
[ ... ]
Reported-by: syzbot+fcf5dd39282ceb27108d@syzkaller.appspotmail.com
Fixes: c5a7591172 ("net/hsr: Use list_head (and rcu) instead of array for slave devices.")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hsr module has been supporting the list and status command.
(HSR_C_GET_NODE_LIST and HSR_C_GET_NODE_STATUS)
These commands send node information to the user-space via generic netlink.
But, in the non-init_net namespace, these commands are not allowed
because .netnsok flag is false.
So, there is no way to get node information in the non-init_net namespace.
Fixes: f421436a59 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hsr_get_node_list() is to send node addresses to the userspace.
If there are so many nodes, it could fail because of buffer size.
In order to avoid this failure, the restart routine is added.
Fixes: f421436a59 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hsr_get_node_{list/status}() are not under rtnl_lock() because
they are callback functions of generic netlink.
But they use __dev_get_by_index() without rtnl_lock().
So, it would use unsafe data.
In order to fix it, rcu_read_lock() and dev_get_by_index_rcu()
are used instead of __dev_get_by_index().
Fixes: f421436a59 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the commit e0a4b99773 ("hsr: use upper/lower device infrastructure"),
dev_get() was removed but dev_put() in the error path wasn't removed.
So, if creating hsr interface command is failed, the reference counter leak
of lower interface would occur.
Test commands:
ip link add dummy0 type dummy
ip link add ipvlan0 link dummy0 type ipvlan mode l2
ip link add ipvlan1 link dummy0 type ipvlan mode l2
ip link add hsr0 type hsr slave1 ipvlan0 slave2 ipvlan1
ip link del ipvlan0
Result:
[ 633.271992][ T1280] unregister_netdevice: waiting for ipvlan0 to become free. Usage count = -1
Fixes: e0a4b99773 ("hsr: use upper/lower device infrastructure")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev_upper_dev_link() is useful to manage lower/upper interfaces.
And this function internally validates looping, maximum depth.
All or most virtual interfaces that could have a real interface
(e.g. macsec, macvlan, ipvlan etc.) use lower/upper infrastructure.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to access the port list, the hsr_port_get_hsr() is used.
And this is protected by RTNL and RCU.
The hsr_fill_info(), hsr_check_carrier(), hsr_dev_open() and
hsr_get_max_mtu() are protected by RTNL.
So, rcu_read_lock() in these functions are not necessary.
The hsr_handle_frame() also uses rcu_read_lock() but this function
is called by packet path.
It's already protected by RCU.
So, the rcu_read_lock() in hsr_handle_frame() can be removed.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When HSR interface is sending a frame, it finds a node with
the destination ethernet address from the list.
If there is no node, it calls WARN_ONCE().
But, using WARN_ONCE() for this situation is a little bit overdoing.
So, in this patch, the netdev_err() is used instead.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If HSR uses the extack instead of netdev_info(), users can get
error messages immediately without any checking the kernel message.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If it uses debugfs_remove_recursive() instead of debugfs_remove(),
hsr_priv() doesn't need to have "node_tbl_file" pointer variable.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
node_db is traversed using list_for_each_entry_rcu
outside an RCU read-side critical section but under the protection
of hsr->list_lock.
Hence, add corresponding lockdep expression to silence false-positive
warnings, and harden RCU lists.
Signed-off-by: Amol Grover <frextrite@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>