genlmsg_end() cannot fail, it just returns the length
of the message. Thus, error handling for it is useless.
While removing it, I also noticed a useless variable
and removed this it as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reuse the already existing struct nl80211_sta_flag_update to specify
both, a flag mask and the flag set itself. This means
nl80211_sta_flag_update is now used for setting station flags and also
for getting station flags.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mark the STA entries of enabled TDLS peers with a new "peer authorized"
flag.
During link setup, allow special TDLS setup frames through the AP, but
otherwise drop all packets destined to the peer. This is required by the
TDLS (802.11z) specification in order to prevent reordering of MSDUs
between the AP and direct paths.
When setup completes and the peer is authorized, send data directly,
bypassing the AP.
In the Rx path, allow data to be received directly from TDLS peers.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When adding a TDLS peer STA, mark it with a new flag in both nl80211 and
mac80211. Before adding a peer, make sure the wiphy supports TDLS and
our operating mode is appropriate (managed).
In addition, make sure all peers are removed on disassociation.
A TDLS peer is first added just before link setup is initiated. In later
setup stages we have more info about peer supported rates, capabilities,
etc. This info is reported via nl80211_set_station().
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for sending high-level TDLS commands and TDLS frames via
NL80211_CMD_TDLS_OPER and NL80211_CMD_TDLS_MGMT, respectively. Add
appropriate cfg80211 callbacks for lower level drivers.
Add wiphy capability flags for TDLS support and advertise them via
nl80211.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, when hostapd sets the station as authorized
we also overwrite its uAPSD parameter. This obviously
leads to buggy behaviour (later, with my patches that
actually add uAPSD support). To fix this, only apply
those parameters if they were actually set in nl80211,
and to achieve that add a bitmap of things to apply.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Correct flag usage - use it as a bit index instead of a bit value.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
tx params are currently configured per hw, although they
should be configured per interface.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new nl80211 attribute to specify whether to send the management
frames in CCK rate or not. As of now the wpa_supplicant is disabling
CCK rate at P2P init itself. So this patch helps to send P2P probe
request/probe response/action frames being sent at non CCK rate in 2GHz
without disabling 11b rates.
This attribute is used with NL80211_CMD_TRIGGER_SCAN and
NL80211_CMD_FRAME commands to disable CCK rate for management frame
transmission.
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of using a hardcoded list of cipher suites in nl80211.c, use a
shared function in util.c to verify that the driver advertises support
for the specified cipher. This provides more accurate validation of the
values and allows vendor-specific cipher suites to be added in drivers.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
NL80211_ATTR_AKM_SUITES can be used to configure new AKMs, like FT or
the SHA-256 -based AKMs or FT from 802.11r/802.11w. In addition, vendor
specific AKMs could be used. The current validation code for the connect
command prevents cfg80211-based drivers from using these mechanisms even
if the driver would not actually use this AKM value (i.e., it uses
WPA/RSN IE from user space). mac80211-based drivers allow any AKM to be
used since this value is not used there.
Remove the unnecessary validation step in cfg80211 to allow drivers to
decide what AKMs are supported. In theory, we could handle this by
advertising supported AKMs, but that would not be very effective unless
we enforce all drivers (including mac80211) to advertise the set of
supported AKMs. This would require additional changes in many places
whenever a new AKM is introduced even though no actually functionality
changes may be required in most drivers.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Incorrect variable was used in validating the akm_suites array from
NL80211_ATTR_AKM_SUITES. In addition, there was no explicit
validation of the array length (we only have room for
NL80211_MAX_NR_AKM_SUITES).
This can result in a buffer write overflow for stack variables with
arbitrary data from user space. The nl80211 commands using the affected
functionality require GENL_ADMIN_PERM, so this is only exposed to admin
users.
Cc: stable@kernel.org
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211_conn_scan allows disabled channels at scan request.
Hence probe request was seen at the disabled one. This patch
ensures that disabled channel never be added into the scan
request's channel list.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the driver (or most likely firmware) decides which AP to use
for roaming based on internal scan result processing, user space
needs to be notified of PMKSA caching candidates to allow RSN
pre-authentication to be used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The IBSS BSSID is never validated, so an
invalid one might end up being used. Fix
this by rejecting invalid configuration.
Reported-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add function to find vendor-specific ie (along with
vendor-specific ie struct definition and P2P OUI values)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The scan request received from cfg80211_connect do not
have proper rate mast. So the probe request sent on each
channel do not have proper the supported rates ie.
Cc: stable@kernel.org
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During the association, the regulatory is updated by country IE
that reaps the previously found beacons. The impact is that
after a STA disconnects *or* when for any reason a regulatory
domain change happens the beacon hint flag is not cleared
therefore preventing future beacon hints to be learned.
This is important as a regulatory domain change or a restore
of regulatory settings would set back the passive scan and no-ibss
flags on the channel. This is the right place to do this given that
it covers any regulatory domain change.
Cc: stable@kernel.org
Reviewed-by: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The format is intended to be like the subfields
in the QoS Info field, verify that is the case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reorder functions to remove the need for a forward declaration
introduced by the last commit.
Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Cc: Daniel Mack <daniel@zonque.org>
Cc: linux-wireless@vger.kernel.org
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function wiphy_update_regulatory() uses the static variable
last_request and thus needs to be called with reg_mutex held.
This is the case for all users in reg.c, but the function was
exported for use by wiphy_register(), from where it is called
without the lock being held.
Fix this by making wiphy_update_regulatory() private and introducing
regulatory_update() as a wrapper that acquires and holds the lock.
Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Cc: Daniel Mack <daniel@zonque.org>
Cc: linux-wireless@vger.kernel.org
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Two spaces and the second "KHz" suggest that the code author meant to
print the bandwidth but forgot it. The code appears in commit e702d3cf
already with two spaces and "KHz" in place of the bandwidth.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce filtering for scheduled scans to reduce the number of
unnecessary results (which cause useless wake-ups).
Add a new nested attribute where sets of parameters to be matched can
be passed when starting a scheduled scan. Only scan results that
match any of the sets will be returned.
At this point, the set consists of a single parameter, an SSID. This
can be easily extended in the future to support more complex matches.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add WIPHY_FLAG_AP_UAPSD flag to indicate uapsd support on
AP mode.
Advertise it to userspace by including a new
NL80211_ATTR_SUPPORT_AP_UAPSD attribute.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Removing unnecessary messages saves code and text.
Site specific OOM messages are duplications of a generic MM
out of memory message and aren't really useful, so just
delete them.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the rssi of the current AP drops, both wpa_supplicant and the
firmware may do a background scan to find a better AP and try to
associate. Since firmware based roaming is faster, inform
wpa_supplicant to avoid roaming and let the firmware decide to
roam if necessary.
For fullmac drivers like ath6kl, it is just enough to provide the
ESSID and the firmware will decide on the BSSID. Since it is not
possible to do pre-auth during roaming for fullmac drivers, the
wpa_supplicant needs to completely disconnect with the old AP and
reconnect with the new AP. This consumes lot of time and it is
better to leave the roaming decision to the firmware.
Signed-off-by: Vivek Natarajan <nataraja@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new NL80211_ATTR_STA_WME nested attribute that contains
wme params needed by the low-level driver (uapsd_queues and
max_sp).
Add these params to the station_parameters struct as well.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow userspace to set NL80211_MESHCONF_GATE_ANNOUNCEMENTS attribute,
which will advertise this mesh node as being a mesh gate.
NL80211_HWMP_ROOTMODE must be set or this will do nothing.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow userspace to set Root Announcement Interval for our mesh
interface. Also, RANN interval is now in proper units of TUs.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fix allows userspace to mark a meshif as a root node.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates the mesh peering frames to the format specified in
the recently ratified 802.11s standard. Several changes took place to
make this happen:
- Change RX path to handle new self-protected frames
- Add new Peering management IE
- Remove old Peer Link IE
- Remove old plink_action field in ieee80211_mgmt header
These changes by themselves would either break peering, or work by
coincidence, so squash them all into this patch.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The NL80211_CMD_NEW_BEACON command is, in practice, requesting AP mode
operations to be started. Add new attributes to provide extra IEs
(e.g., WPS IE, P2P IE) for drivers that build Beacon, Probe Response,
and (Re)Association Response frames internally (likely in firmware).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes need from drivers to parse the beacon tail/head data
to figure out what crypto settings are to be used in AP mode in case
the Beacon and Probe Response frames are fully constructed in the
driver/firmware.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes it easier for drivers that generate Beacon and Probe Response
frames internally (in firmware most likely) in AP mode.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Moving the parsing logic for retrieving the information elements
stored in management frames, e.g. beacons or probe responses,
and making it available to other cfg80211 drivers.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a comment pointing out the use of enum station_info_flags for
all new struct station_info fields. In addition, memset the sinfo
buffer to zero before use on all paths in the current tree to avoid
leaving uninitialized pointers in the data.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 leaves sinfo->assoc_req_ies uninitialized, causing a random
pointer memory access in nl80211_send_station.
Instead of checking if the pointer is null, use sinfo->filled, like
the rest of the fields.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When user space SME/MLME (e.g., hostapd) is not used in AP mode, the
IEs from the (Re)Association Request frame that was processed in
firmware need to be made available for user space (e.g., RSN IE for
hostapd). Allow this to be done with cfg80211_new_sta().
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers that support frame transmission with mgmt_tx() may not support
driver-based offchannel TX. Use mgmt_tx_cancel_wait instead of mgmt_tx
when figuring out whether to indicate support for this with
NL80211_ATTR_OFFCHANNEL_TX_OK.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Several uses were missing terminating newlines.
Typo fix and macro neatening.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A lot of code is dedicated to giving drivers the
ability to use cfg80211's wext handlers without
completely converting. However, only orinoco is
currently using this, and it is only partially
using it.
We reduce the size of both the source and binary
by removing those that nobody needs. If a driver
shows up that needs it during conversion, we can
add back those that are needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A lot of drivers erroneously use wext constants
and don't notice since cfg80211.h includes them.
Make this more split up so drivers needing wext
compatibility from cfg80211 need to explicitly
include that from cfg80211-wext.h.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The test is off by one so we'd read past the end of the
wiphy->bands[] array on the next line.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just a typo fix changing regulaotry to regulatory.
Signed-off-by: Mihai Moldovan <ionic@ionic.de>
CC: John W. Linville <linville@tuxdriver.com>
CC: Mohammed Shafi <shafi.wireless@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At the beginning of wiphy_update_regulatory() a check is performed
whether the request is to be ignored. Then the request is sent to
the driver nevertheless. This happens even if last_request points
to NULL, leading to a crash in the driver:
[<bf01d864>] (lbs_set_11d_domain_info+0x28/0x1e4 [libertas]) from [<c03b714c>] (wiphy_update_regulatory+0x4d0/0x4f4)
[<c03b714c>] (wiphy_update_regulatory+0x4d0/0x4f4) from [<c03b4008>] (wiphy_register+0x354/0x420)
[<c03b4008>] (wiphy_register+0x354/0x420) from [<bf01b17c>] (lbs_cfg_register+0x80/0x164 [libertas])
[<bf01b17c>] (lbs_cfg_register+0x80/0x164 [libertas]) from [<bf020e64>] (lbs_start_card+0x20/0x88 [libertas])
[<bf020e64>] (lbs_start_card+0x20/0x88 [libertas]) from [<bf02cbd8>] (if_sdio_probe+0x898/0x9c0 [libertas_sdio])
Fix this by returning early. Also remove the out: label as it is
not any longer needed.
Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Cc: linux-wireless@vger.kernel.org
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Daniel Mack <daniel@zonque.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit 58389c69150e6032504dfcd3edca6b1975c8b5bc
Author: Johannes Berg <johannes.berg@intel.com>
Date: Mon Jul 18 18:08:35 2011 +0200
cfg80211: allow userspace to control supported rates in scan
made single-band cards crash since it would always
access all wiphy->bands[]. Fix this and reject any
attempts in the new helper ieee80211_get_ratemask()
to do the same, rejecting rates configuration for
unsupported bands.
Reported-by: Pavel Roskin <proski@gnu.org>
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
