One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct virtio_scsi {
...
struct virtio_scsi_vq req_vqs[];
};
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.
So, replace the following form:
sizeof(*vscsi) + sizeof(vscsi->req_vqs[0]) * num_queues
with:
struct_size(vscsi, req_vqs, num_queues)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Pull networking updates from David Miller:
"Some highlights from this development cycle:
1) Big refactoring of ipv6 route and neigh handling to support
nexthop objects configurable as units from userspace. From David
Ahern.
2) Convert explored_states in BPF verifier into a hash table,
significantly decreased state held for programs with bpf2bpf
calls, from Alexei Starovoitov.
3) Implement bpf_send_signal() helper, from Yonghong Song.
4) Various classifier enhancements to mvpp2 driver, from Maxime
Chevallier.
5) Add aRFS support to hns3 driver, from Jian Shen.
6) Fix use after free in inet frags by allocating fqdirs dynamically
and reworking how rhashtable dismantle occurs, from Eric Dumazet.
7) Add act_ctinfo packet classifier action, from Kevin
Darbyshire-Bryant.
8) Add TFO key backup infrastructure, from Jason Baron.
9) Remove several old and unused ISDN drivers, from Arnd Bergmann.
10) Add devlink notifications for flash update status to mlxsw driver,
from Jiri Pirko.
11) Lots of kTLS offload infrastructure fixes, from Jakub Kicinski.
12) Add support for mv88e6250 DSA chips, from Rasmus Villemoes.
13) Various enhancements to ipv6 flow label handling, from Eric
Dumazet and Willem de Bruijn.
14) Support TLS offload in nfp driver, from Jakub Kicinski, Dirk van
der Merwe, and others.
15) Various improvements to axienet driver including converting it to
phylink, from Robert Hancock.
16) Add PTP support to sja1105 DSA driver, from Vladimir Oltean.
17) Add mqprio qdisc offload support to dpaa2-eth, from Ioana
Radulescu.
18) Add devlink health reporting to mlx5, from Moshe Shemesh.
19) Convert stmmac over to phylink, from Jose Abreu.
20) Add PTP PHC (Physical Hardware Clock) support to mlxsw, from
Shalom Toledo.
21) Add nftables SYNPROXY support, from Fernando Fernandez Mancera.
22) Convert tcp_fastopen over to use SipHash, from Ard Biesheuvel.
23) Track spill/fill of constants in BPF verifier, from Alexei
Starovoitov.
24) Support bounded loops in BPF, from Alexei Starovoitov.
25) Various page_pool API fixes and improvements, from Jesper Dangaard
Brouer.
26) Just like ipv4, support ref-countless ipv6 route handling. From
Wei Wang.
27) Support VLAN offloading in aquantia driver, from Igor Russkikh.
28) Add AF_XDP zero-copy support to mlx5, from Maxim Mikityanskiy.
29) Add flower GRE encap/decap support to nfp driver, from Pieter
Jansen van Vuuren.
30) Protect against stack overflow when using act_mirred, from John
Hurley.
31) Allow devmap map lookups from eBPF, from Toke Høiland-Jørgensen.
32) Use page_pool API in netsec driver, Ilias Apalodimas.
33) Add Google gve network driver, from Catherine Sullivan.
34) More indirect call avoidance, from Paolo Abeni.
35) Add kTLS TX HW offload support to mlx5, from Tariq Toukan.
36) Add XDP_REDIRECT support to bnxt_en, from Andy Gospodarek.
37) Add MPLS manipulation actions to TC, from John Hurley.
38) Add sending a packet to connection tracking from TC actions, and
then allow flower classifier matching on conntrack state. From
Paul Blakey.
39) Netfilter hw offload support, from Pablo Neira Ayuso"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2080 commits)
net/mlx5e: Return in default case statement in tx_post_resync_params
mlx5: Return -EINVAL when WARN_ON_ONCE triggers in mlx5e_tls_resync().
net: dsa: add support for BRIDGE_MROUTER attribute
pkt_sched: Include const.h
net: netsec: remove static declaration for netsec_set_tx_de()
net: netsec: remove superfluous if statement
netfilter: nf_tables: add hardware offload support
net: flow_offload: rename tc_cls_flower_offload to flow_cls_offload
net: flow_offload: add flow_block_cb_is_busy() and use it
net: sched: remove tcf block API
drivers: net: use flow block API
net: sched: use flow block API
net: flow_offload: add flow_block_cb_{priv, incref, decref}()
net: flow_offload: add list handling functions
net: flow_offload: add flow_block_cb_alloc() and flow_block_cb_free()
net: flow_offload: rename TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_*
net: flow_offload: rename TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND
net: flow_offload: add flow_block_cb_setup_simple()
net: hisilicon: Add an tx_desc to adapt HI13X1_GMAC
net: hisilicon: Add an rx_desc to adapt HI13X1_GMAC
...
Pull Documentation updates from Jonathan Corbet:
"It's been a relatively busy cycle for docs:
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with
other trees, unfortunately. He has a lot more of these waiting on
the wings that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos,
and one on Spectre vulnerabilities.
- Various improvements to the build system, including automatic
markup of function() references because some people, for reasons I
will never understand, were of the opinion that
:c:func:``function()`` is unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc"
* tag 'docs-5.3' of git://git.lwn.net/linux: (129 commits)
docs: automarkup.py: ignore exceptions when seeking for xrefs
docs: Move binderfs to admin-guide
Disable Sphinx SmartyPants in HTML output
doc: RCU callback locks need only _bh, not necessarily _irq
docs: format kernel-parameters -- as code
Doc : doc-guide : Fix a typo
platform: x86: get rid of a non-existent document
Add the RCU docs to the core-api manual
Documentation: RCU: Add TOC tree hooks
Documentation: RCU: Rename txt files to rst
Documentation: RCU: Convert RCU UP systems to reST
Documentation: RCU: Convert RCU linked list to reST
Documentation: RCU: Convert RCU basic concepts to reST
docs: filesystems: Remove uneeded .rst extension on toctables
scripts/sphinx-pre-install: fix out-of-tree build
docs: zh_CN: submitting-drivers.rst: Remove a duplicated Documentation/
Documentation: PGP: update for newer HW devices
Documentation: Add section about CPU vulnerabilities for Spectre
Documentation: platform: Delete x86-laptop-drivers.txt
docs: Note that :c:func: should no longer be used
...
Pull block updates from Jens Axboe:
"This is the main block updates for 5.3. Nothing earth shattering or
major in here, just fixes, additions, and improvements all over the
map. This contains:
- Series of documentation fixes (Bart)
- Optimization of the blk-mq ctx get/put (Bart)
- null_blk removal race condition fix (Bob)
- req/bio_op() cleanups (Chaitanya)
- Series cleaning up the segment accounting, and request/bio mapping
(Christoph)
- Series cleaning up the page getting/putting for bios (Christoph)
- block cgroup cleanups and moving it to where it is used (Christoph)
- block cgroup fixes (Tejun)
- Series of fixes and improvements to bcache, most notably a write
deadlock fix (Coly)
- blk-iolatency STS_AGAIN and accounting fixes (Dennis)
- Series of improvements and fixes to BFQ (Douglas, Paolo)
- debugfs_create() return value check removal for drbd (Greg)
- Use struct_size(), where appropriate (Gustavo)
- Two lighnvm fixes (Heiner, Geert)
- MD fixes, including a read balance and corruption fix (Guoqing,
Marcos, Xiao, Yufen)
- block opal shadow mbr additions (Jonas, Revanth)
- sbitmap compare-and-exhange improvemnts (Pavel)
- Fix for potential bio->bi_size overflow (Ming)
- NVMe pull requests:
- improved PCIe suspent support (Keith Busch)
- error injection support for the admin queue (Akinobu Mita)
- Fibre Channel discovery improvements (James Smart)
- tracing improvements including nvmetc tracing support (Minwoo Im)
- misc fixes and cleanups (Anton Eidelman, Minwoo Im, Chaitanya
Kulkarni)"
- Various little fixes and improvements to drivers and core"
* tag 'for-5.3/block-20190708' of git://git.kernel.dk/linux-block: (153 commits)
blk-iolatency: fix STS_AGAIN handling
block: nr_phys_segments needs to be zero for REQ_OP_WRITE_ZEROES
blk-mq: simplify blk_mq_make_request()
blk-mq: remove blk_mq_put_ctx()
sbitmap: Replace cmpxchg with xchg
block: fix .bi_size overflow
block: sed-opal: check size of shadow mbr
block: sed-opal: ioctl for writing to shadow mbr
block: sed-opal: add ioctl for done-mark of shadow mbr
block: never take page references for ITER_BVEC
direct-io: use bio_release_pages in dio_bio_complete
block_dev: use bio_release_pages in bio_unmap_user
block_dev: use bio_release_pages in blkdev_bio_end_io
iomap: use bio_release_pages in iomap_dio_bio_end_io
block: use bio_release_pages in bio_map_user_iov
block: use bio_release_pages in bio_unmap_user
block: optionally mark pages dirty in bio_release_pages
block: move the BIO_NO_PAGE_REF check into bio_release_pages
block: skd_main.c: Remove call to memset after dma_alloc_coherent
block: mtip32xx: Remove call to memset after dma_alloc_coherent
...
Merge 5.2-rc6 into for-5.3/block, so we get the same page merge leak
fix. Otherwise we end up having conflicts with future patches between
for-5.3/block and master that touch this area. In particular, it makes
the bio_full() fix hard to backport to stable.
* tag 'v5.2-rc6': (482 commits)
Linux 5.2-rc6
Revert "iommu/vt-d: Fix lock inversion between iommu->lock and device_domain_lock"
Bluetooth: Fix regression with minimum encryption key size alignment
tcp: refine memory limit test in tcp_fragment()
x86/vdso: Prevent segfaults due to hoisted vclock reads
SUNRPC: Fix a credential refcount leak
Revert "SUNRPC: Declare RPC timers as TIMER_DEFERRABLE"
net :sunrpc :clnt :Fix xps refcount imbalance on the error path
NFS4: Only set creation opendata if O_CREAT
ARM: 8867/1: vdso: pass --be8 to linker if necessary
KVM: nVMX: reorganize initial steps of vmx_set_nested_state
KVM: PPC: Book3S HV: Invalidate ERAT when flushing guest TLB entries
habanalabs: use u64_to_user_ptr() for reading user pointers
nfsd: replace Jeff by Chuck as nfsd co-maintainer
inet: clear num_timeout reqsk_alloc()
PCI/P2PDMA: Ignore root complex whitelist when an IOMMU is present
net: mvpp2: debugfs: Add pmap to fs dump
ipv6: Default fib6_type to RTN_UNICAST when not set
net: hns3: Fix inconsistent indenting
net/af_iucv: always register net_device notifier
...
Pull SCSI fix from James Bottomley:
"One simple fix for a driver use after free"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: vmw_pscsi: Fix use-after-free in pvscsi_queue_lck()
The new route handling in ip_mc_finish_output() from 'net' overlapped
with the new support for returning congestion notifications from BPF
programs.
In order to handle this I had to take the dev_loopback_xmit() calls
out of the switch statement.
The aquantia driver conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
On session deletion, current qla code would unregister an NVMe session
before flushing IOs. This patch would move the unregistration of NVMe
session after IO flush. This way FC-NVMe layer would not have to wait for
stuck IOs. In addition, qla2xxx would stop accepting new IOs during session
deletion.
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch uses kref to protect access between fcp_abort path and nvme
command and LS command completion path. Stack trace below shows the abort
path is accessing stale memory (nvme_private->sp).
When command kref reaches 0, nvme_private & srb resource will be
disconnected from each other. Any subsequence nvme abort request will not
be able to reference the original srb.
[ 5631.003998] BUG: unable to handle kernel paging request at 00000010000005d8
[ 5631.004016] IP: [<ffffffffc087df92>] qla_nvme_abort_work+0x22/0x100 [qla2xxx]
[ 5631.004086] Workqueue: events qla_nvme_abort_work [qla2xxx]
[ 5631.004097] RIP: 0010:[<ffffffffc087df92>] [<ffffffffc087df92>] qla_nvme_abort_work+0x22/0x100 [qla2xxx]
[ 5631.004109] Call Trace:
[ 5631.004115] [<ffffffffaa4b8174>] ? pwq_dec_nr_in_flight+0x64/0xb0
[ 5631.004117] [<ffffffffaa4b9d4f>] process_one_work+0x17f/0x440
[ 5631.004120] [<ffffffffaa4bade6>] worker_thread+0x126/0x3c0
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffffc050d10c>] qla_nvme_unregister_remote_port+0x6c/0xf0 [qla2xxx]
PGD 800000084cf41067 PUD 84d288067 PMD 0
Oops: 0000 [#1] SMP
Call Trace:
[<ffffffff98abcfdf>] process_one_work+0x17f/0x440
[<ffffffff98abdca6>] worker_thread+0x126/0x3c0
[<ffffffff98abdb80>] ? manage_workers.isra.26+0x2a0/0x2a0
[<ffffffff98ac4f81>] kthread+0xd1/0xe0
[<ffffffff98ac4eb0>] ? insert_kthread_work+0x40/0x40
[<ffffffff9918ad37>] ret_from_fork_nospec_begin+0x21/0x21
[<ffffffff98ac4eb0>] ? insert_kthread_work+0x40/0x40
RIP [<ffffffffc050d10c>] qla_nvme_unregister_remote_port+0x6c/0xf0 [qla2xxx]
The crash is due to a bad entry in the nvme_rport_list. This list is not
protected, and when a remoteport_delete callback is called, driver
traverses the list and crashes.
Actually, the list could be removed and driver could traverse the main
fcport list instead. Fix does exactly that.
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For Aero adapters, driver provides three different performance modes
controlled through module parameter named 'perf_mode'. Below are those
performance modes:
0: Balanced - Additional high IOPS reply queues will be enabled along with
low latency queues. Interrupt coalescing will be enabled only for these
high IOPS reply queues.
1: IOPS - No additional high IOPS queues are enabled. Interrupt coalescing
will be enabled on all reply queues.
2: Latency - No additional high IOPS queues are enabled. Interrupt
coalescing will be disabled on all reply queues. This is a legacy
behavior similar to Ventura & Invader Series.
Default performance mode settings:
- Performance mode set to 'Balanced', if Aero controller is working in
16GT/s PCIe speed.
- Performance mode will be set to 'Latency' mode for all other cases.
Through module parameter 'perf_mode', user can override default performance
mode to desired one.
Captured some performance numbers with these performance modes. 4k Random
Read IO performance numbers on 24 SAS SSD drives for above three
performance modes. Performance data is from Intel Skylake and HGST SS300
(drive model SDLL1DLR400GCCA1).
IOPS:
-----------------------------------------------------------------------
|perf_mode | qd = 1 | qd = 64 | note |
|-------------|--------|---------|-------------------------------------
|balanced | 259K | 3061k | Provides max performance numbers |
| | | | both on lower QD workload & |
| | | | also on higher QD workload |
|-------------|--------|---------|-------------------------------------
|iops | 220K | 3100k | Provides max performance numbers |
| | | | only on higher QD workload. |
|-------------|--------|---------|-------------------------------------
|latency | 246k | 2226k | Provides good performance numbers |
| | | | only on lower QD worklaod. |
-----------------------------------------------------------------------
Average Latency:
-----------------------------------------------------
|perf_mode | qd = 1 | qd = 64 |
|-------------|--------------|----------------------|
|balanced | 92.05 usec | 501.12 usec |
|-------------|--------------|----------------------|
|iops | 108.40 usec | 498.10 usec |
|-------------|--------------|----------------------|
|latency | 97.10 usec | 689.26 usec |
-----------------------------------------------------
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver will use round-robin method for IO submission in batches within
the high IOPS queues when the number of in-flight ios on the target device
is larger than 8. Otherwise the driver will use low latency reply queues.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
High iops queues are mapped to non-managed IRQs. Set affinity of
non-managed irqs to local numa node. Low latency queues are mapped to
managed IRQs.
Driver reserves some reply queues for high IOPS queues (through
pci_alloc_irq_vectors_affinity and .pre_vectors interface). The rest of
queues are for low latency.
Based on IO workload, driver will decide which group of reply queues
(either high IOPS queues or low latency queues) to be used.
High IOPS queues will be mapped to local numa node of controller and
low latency queues will be mapped to CPUs across numa nodes. In general,
high IOPS and low latency queues should fit into 128 reply queues
which is the max number of reply queues supported by Aero adapters.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver should enable interrupt coalescing (during driver load and after
Controller Reset) for High IOPS queues by masking appropriate bits in IOC
INIT frame.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Aero controllers support balanced performance mode through the ability to
configure queues with different properties.
Reply queues with interrupt coalescing enabled are called "high iops reply
queues" and reply queues with interrupt coalescing disabled are called "low
latency reply queues".
The driver configures a combination of high iops and low latency reply
queues if:
- HBA is an AERO controller;
- MSI-X vectors supported by the HBA is 128;
- Total CPU count in the system more than high iops queue count;
- Driver is loaded with default max_msix_vectors module parameter; and
- System booted in non-kdump mode.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For RAID5/RAID6 volumes configured behind Aero, driver will be doing 64bit
division operations on behalf of firmware as controller's ARM CPU is very
slow in this division. Later, driver calculates Q-ARM, P-ARM and Log-ARM and
passes those values to firmware by writing these values to RAID_CONTEXT.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Issue: This issue is applicable to scenario when JBOD sequence map is
unavailable (memory allocation for JBOD sequence map failed) to driver but
feature is supported by firmware. If the driver sends a JBOD IO by not
adding 255 (MAX_PHYSICAL_DEVICES - 1) to device ID when underlying firmware
supports JBOD sequence map, it will lead to the IO failure.
Fix: For JBOD IOs, driver will not use the RAID map to fetch the devhandle
if JBOD sequence map is unavailable. Driver will set Devhandle to 0xffff
and Target ID to 'device ID + 255 (MAX_PHYSICAL_DEVICES - 1)'.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Firmware does not expect FastPath IO sent through Region Lock Bypass queue.
Though firmware never exposes such settings when fastpath IO can be sent to
RL bypass queue but it's safer to remove dead code which directs fastpath
IO to RL Bypass queue.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Issue: Under certain conditions, controller goes in FAULT state after IOC
INIT fired to firmware. Such Fault can be recovered through controller
reset.
Fix: In driver probe context, if firmware fault is observed post IOC INIT,
driver would do controller reset followed by retry logic for IOC INIT
command.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Issue: There is possibility of few DCMDs timing out with 'reset_mutex' lock
held. As part of DCMD timeout handling, driver calls function
megasas_reset_fusion which also tries to acquire same lock 'reset_mutex'
and end up with deadlock.
Fix: Upon timeout of DCMDs (which are fired with 'reset_mutex' lock held),
driver will release 'reset_mutex' before calling OCR function and will
acquire lock again after OCR function returns.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On PowerPC architecture, calling disable_irq_nosync from IRQ context is not
providing the required effect.
In current megaraid_sas driver, disable_irq_nosync is being called from IRQ
context before enabling IRQ poll. But due to the issue seen on PPC, after
IRQ poll disable and legacy ISR is enabled, we are not seeing our ISR
getting called.
Fix: Call disable_irq from IRQ poll thread context instead of IRQ context.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch will add support for non-secure Aero adapter PCI IDs. Driver
will throw an error message when a non-secure type controller is
detected. Purpose of this interface is to avoid interacting with any
firmware which is not secured/signed by Broadcom. Any tampering on Firmware
component will be detected by hardware and it will be communicated to the
driver to avoid any further interaction with that component.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Aero adapters provides Atomic Request Descriptor as an alternative method
for posting an entry onto a request queue. The posting of an Atomic Request
Descriptor is an atomic operation, providing a safe mechanism for multiple
processors on the host to post requests without synchronization. This
Atomic Request Descriptor format is identical to first 32 bits of Default
Request Descriptor and uses only 32 bits.
If Aero adapters support Atomic descriptor, driver should use it for
posting IOs and DCMDs to firmware.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enable msix load balance only when combined reply queue mode is disabled on
the SAS3 and above generation HBA devices.
Earlier msix load balance used to enable if the number of online cpus is
greater than the number of MSI-X vectors enabled on the HBA. Combined reply
queue mode will be disabled only on those HBA which works in shared
resources mode. I.e. on SAS3 HBAs it will be <= 8 and on SAS35 HBA devices
it will be <= 16.
- Before this patch if system has 256 logical CPUs and HBA exposes 128
MSI-X vectors, driver will enable msix load balance.
- After this patch if system has 256 logical CPUs and HBA exposes 128
MSI-X vectors, driver will disable msix load balance.
- After this patch if system has 256 logical CPUs and HBA exposes 16 MSI-X
vectors (due to combined reply queue mode being off in HW), driver will
enable msix load balance.
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Even though 'smp_affinity_enable' module parameter is enabled, if the
number of online CPUs is bigger than the number of msix vectors enabled on
that HBA, then smp affinity settings should be disabled only for this HBA.
But currently the smp affinity setting is disabled globally and hence smp
affinity will be disabled for subsequent HBAs even though number of msix
vectors enabled for this HBA matches the number of online CPU.
To fix this, define a per HBA variable smp_affinity_enable. Initially this
variable is initialized with smp_affinity_enable module parameter value. If
this HBA has less number of msix vectors configured when compared to number
of online cpus, then only this HBA's variable smp_affinity_enable is set to
zero.
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When enabling high iops queues, the driver should use the HBA's configured
PCIe link speed instead of looking for the maximum link speed.
I.e. enable high iops queues only if Aero/Sea HBA's configured PCIe link
speed is set to 16GT/s.
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently default perf_mode is set to 'balanced' on Intel architecture
machines and on other machines default perf_mode is set to 'latency' mode.
This CPU architecture check is removed and the default perf_mode mode is
set to 'balanced' mode on all machines.
User can choose the required performance mode using perf_mode module
parameter.
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If cb_arg alloc failed, we can't release the struct orig_io_req refcount
before we take its refcount. As Saurav said, move the srr_err label down
to avoid unnecessary refcount release and nullptr free.
Signed-off-by: Lin Yi <teroincn@163.com>
Acked-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If cb_arg alloc failed, we can't release the struct orig_io_req refcount
before we take its refcount. As Saurav said, move the rec_err label down
to avoid unnecessary refcount release and nullptr free.
Signed-off-by: Lin Yi <teroincn@163.com>
Acked-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- Reduce the sg_tablesize to 255.
- Reduce the MAX BDs firmware can handle to 255.
- Return IO to ML if BD goes more then 255 after split.
- Correct the size of each BD split to 0xffff.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If firmware sends either cleanup or abort completion, it means other won't
be sent. Clean out flags for other as well.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Separate out abort and cleanup flag and completion, to have better
understaning of what is getting processed.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In certain tests where the SCSI error handler issues an abort that is
already outstanding, we will cleanup the command so that the SCSI error
handler can proceed. In some of these cases we were seeing a command
mismatch:
kernel: scsi host2: bnx2fc: xid:0x42b eh_abort - refcnt = 2
kernel: bnx2fc: eh_abort: io_req (xid = 0x42b) already in abts processing
kernel: scsi host2: bnx2fc: xid:0x42b Entered bnx2fc_initiate_cleanup
kernel: scsi host2: bnx2fc: xid:0x42b CLEANUP io_req xid = 0x80b
kernel: scsi host2: bnx2fc: xid:0x80b cq_compl- cleanup resp rcvd
kernel: scsi host2: bnx2fc: xid:0x42b complete - rx_state = 9
kernel: scsi host2: bnx2fc: xid:0x42b Entered process_cleanup_compl refcnt = 2, cmd_type = 1
kernel: scsi host2: bnx2fc: xid:0x42b scsi_done. err_code = 0x7
kernel: scsi host2: bnx2fc: xid:0x42b sc=ffff8807f93dfb80, result=0x7, retries=0, allowed=5
kernel: ------------[ cut here ]------------
kernel: WARNING: at /root/rpmbuild/BUILD/netxtreme2-7.14.43/obj/default/bnx2fc-2.12.1/driver/bnx2fc_io.c:1347 bnx2fc_eh_abort+0x56f/0x680 [bnx2fc]()
kernel: xid=0x42b refcount=-1
kernel: Modules linked in:
kernel: nls_utf8 isofs sr_mod cdrom tcp_lp dm_round_robin xt_CHECKSUM iptable_mangle ipt_MASQUERADE nf_nat_masquerade_ipv4 iptable_nat nf_nat_ipv4 nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 xt_conntrack nf_conntrack ipt_REJECT nf_reject_ipv4 tun bridge ebtable_filter ebtables fuse ip6table_filter ip6_tables iptable_filter bnx2fc(OE) cnic(OE) uio fcoe libfcoe 8021q libfc garp mrp scsi_transport_fc stp llc scsi_tgt vfat fat dm_service_time intel_powerclamp coretemp intel_rapl iosf_mbi kvm_intel kvm irqbypass crc32_pclmul ghash_clmulni_intel aesni_intel lrw gf128mul glue_helper ablk_helper cryptd ses enclosure ipmi_ssif i2c_core hpilo hpwdt wmi sg ipmi_devintf pcspkr ipmi_si ipmi_msghandler shpchp acpi_power_meter dm_multipath nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables xfs sd_mod crc_t10dif
kernel: crct10dif_generic bnx2x(OE) crct10dif_pclmul crct10dif_common crc32c_intel mdio ptp pps_core libcrc32c smartpqi scsi_transport_sas fjes uas usb_storage dm_mirror dm_region_hash dm_log dm_mod
kernel: CPU: 9 PID: 2012 Comm: scsi_eh_2 Tainted: G W OE ------------ 3.10.0-514.el7.x86_64 #1
kernel: Hardware name: HPE Synergy 480 Gen10/Synergy 480 Gen10 Compute Module, BIOS I42 03/21/2018
kernel: ffff8807f25a3d98 0000000015e7fa0c ffff8807f25a3d50 ffffffff81685eac
kernel: ffff8807f25a3d88 ffffffff81085820 ffff8807f8e39000 ffff880801ff7468
kernel: ffff880801ff7610 0000000000002002 ffff8807f8e39014 ffff8807f25a3df0
kernel: Call Trace:
kernel: [<ffffffff81685eac>] dump_stack+0x19/0x1b
kernel: [<ffffffff81085820>] warn_slowpath_common+0x70/0xb0
kernel: [<ffffffff810858bc>] warn_slowpath_fmt+0x5c/0x80
kernel: [<ffffffff8168d842>] ? _raw_spin_lock_bh+0x12/0x50
kernel: [<ffffffffa0549e6f>] bnx2fc_eh_abort+0x56f/0x680 [bnx2fc]
kernel: [<ffffffff814570af>] scsi_error_handler+0x59f/0x8b0
kernel: [<ffffffff81456b10>] ? scsi_eh_get_sense+0x250/0x250
kernel: [<ffffffff810b052f>] kthread+0xcf/0xe0
kernel: [<ffffffff810b0460>] ? kthread_create_on_node+0x140/0x140
kernel: [<ffffffff81696418>] ret_from_fork+0x58/0x90
kernel: [<ffffffff810b0460>] ? kthread_create_on_node+0x140/0x140
kernel: ---[ end trace 42deb88f2032b111 ]---
The reason that there was a mismatch is that the SCSI command is actual
returned from the cleanup handler. In previous testing, the type of
cleanup notification we'd get from the CQE did not trigger the code that
returned the SCSI command. To overcome the previous behavior we would put
a reference in bnx2fc_abts_cleanup() to account for the SCSI command.
However, in cases where the SCSI command is actually off, we end up with an
extra put.
The fix for this is to only take the extra put in bnx2fc_abts_cleanup if
the completion for the cleanup times out.
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For bnx2fc, the source FCoE MAC is stored in the fcoe_port struct in the
data_src_mac field. Currently this is set in fcoe_ctlr_recv_flogi which
ends up setting it by simply using fc_fcoe_set_mac() which only uses the
default FCF-MAC. We still want to store the source FCoE MAC in
port->data_src_mac but we want to snoop the FLOGI response payload so as to
set it in the following method:
1. If a granted_mac is found, use that.
2. If not granted_mac is there but there is a FCF-MAP from the FCF then
create the MAC from the FCF-MAP and the destination ID from the frame.
3. If there is no FCF-MAP the use the spec. default FCF-MAP and the
destination ID from the frame.
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the case of UPIU/DME request execution failed in UFS device,
ufs_bsg_request() will complete the failed bsg job by calling
bsg_job_done(). Meanwhile, it returns this error status to blk-mq layer,
then triggers blk-mq completing this request again, this will cause the
following panic.
Call trace:
ll_sc___cmpxchg_case_acq_32+0x4/0x20
complete+0x28/0x70
blk_end_sync_rq+0x24/0x30
blk_mq_end_request+0xb8/0x118
bsg_job_put+0x4c/0x58
bsg_complete+0x20/0x30
blk_done_softirq+0xb4/0xe8
do_softirq+0x154/0x3f0
run_ksoftirqd+0x4c/0x68
smpboot_thread_fn+0x22c/0x268
kthread+0x130/0x138
ret_from_fork+0x10/0x1c
Code: f84107fe d65f03c0 d503201f f9800011 (885ffc10)
---[ end trace d92825bff6326e66 ]---
Kernel panic - not syncing: Fatal exception in interrupt
This patch is to fix this issue. The solution is to complete the ufs-bsg
job only if no error happened.
[mkp: commit description tweak]
Fixes: df032bf27a (scsi: ufs: Add a bsg endpoint that supports UPIUs)
Signed-off-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Correct dev_dbg to dev_err, so as to print out the error information in
case of DME command failed.
Signed-off-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull SCSI fixes from James Bottomley:
"Three driver fixes (and one version number update): a suspend hang in
ufs, a qla hard lock on module removal and a qedi panic during
discovery"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: qla2xxx: Fix hardlockup in abort command during driver remove
scsi: ufs: Avoid runtime suspend possibly being blocked forever
scsi: qedi: update driver version to 8.37.0.20
scsi: qedi: Check targetname while finding boot target information
