The code in efi.c uses early_memremap(), but relies on a transitive
include rather than including asm/early_ioremap.h directly, since
this header did not exist on ia64.
Commit f7d9248942 ("arm64/efi: refactor EFI init and runtime code
for reuse by 32-bit ARM") attempted to work around this by including
asm/efi.h, which transitively includes asm/early_ioremap.h on most
architectures. However, since asm/efi.h does not exist on ia64 either,
this is not much of an improvement.
Now that we have created an asm/early_ioremap.h for ia64, we can just
include it directly.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Pull ARM updates from Russell King:
- UEFI boot and runtime services support for ARM from Ard Biesheuvel
and Roy Franz.
- DT compatibility with old atags booting protocol for Nokia N900
devices from Ivaylo Dimitrov.
- PSCI firmware interface using new arm-smc calling convention from
Jens Wiklander.
- Runtime patching for udiv/sdiv instructions for ARMv7 CPUs that
support these instructions from Nicolas Pitre.
- L2x0 cache updates from Dirk B and Linus Walleij.
- Randconfig fixes from Arnd Bergmann.
- ARMv7M (nommu) updates from Ezequiel Garcia
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (34 commits)
ARM: 8481/2: drivers: psci: replace psci firmware calls
ARM: 8480/2: arm64: add implementation for arm-smccc
ARM: 8479/2: add implementation for arm-smccc
ARM: 8478/2: arm/arm64: add arm-smccc
ARM: 8494/1: mm: Enable PXN when running non-LPAE kernel on LPAE processor
ARM: 8496/1: OMAP: RX51: save ATAGS data in the early boot stage
ARM: 8495/1: ATAGS: move save_atags() to arch/arm/include/asm/setup.h
ARM: 8452/3: PJ4: make coprocessor access sequences buildable in Thumb2 mode
ARM: 8482/1: l2x0: make it possible to disable outer sync from DT
ARM: 8488/1: Make IPI_CPU_BACKTRACE a "non-secure" SGI
ARM: 8487/1: Remove IPI_CALL_FUNC_SINGLE
ARM: 8485/1: cpuidle: remove cpu parameter from the cpuidle_ops suspend hook
ARM: 8484/1: Documentation: l2c2x0: Mention separate controllers explicitly
ARM: 8483/1: Documentation: l2c: Rename l2cc to l2c2x0
ARM: 8477/1: runtime patch udiv/sdiv instructions into __aeabi_{u}idiv()
ARM: 8476/1: VDSO: use PTR_ERR_OR_ZERO for vma check
ARM: 8453/2: proc-v7.S: don't locate temporary stack space in .text section
ARM: add UEFI stub support
ARM: wire up UEFI init and runtime support
ARM: only consider memblocks with NOMAP cleared for linear mapping
...
- Support for a separate IRQ stack, although we haven't reduced the size
of our thread stack just yet since we don't have enough data to
determine a safe value
- Refactoring of our EFI initialisation and runtime code into
drivers/firmware/efi/ so that it can be reused by arch/arm/.
- Ftrace improvements when unwinding in the function graph tracer
- Document our silicon errata handling process
- Cache flushing optimisation when mapping executable pages
- Support for hugetlb mappings using the contiguous hint in the pte
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJWj+pFAAoJELescNyEwWM0/V8IALu8i2d6LijVICyZ/MH6pK+F
krbkIjdKFmIoFqo8HolCDMDqWfdzCLW671iYmks1DYVqM0Q5SXRa1rIzMw1Nbd3s
PzHS8qvnJFGtjXgwX5yxcyA5nU5hG5/mHJ8tbEg4zlQXvGONU6rZOlt4xY3ocZR7
iWmqoNX8LbPv5UgpifQ06QXEiC+4pm/BgADl2995oZfOaZ37L6c0oh6VcxQWyEf8
7OFRYtwruNyX2S5zJkL41Rh8gFAL9/j7lrHt2D+cxHR58X+qiRYKTjxkwJUt6i3E
ROZROsdQpyHojIIIYZEfNCZWjV0NwSghQfCnbsDwxVkkVeY414UXIno8JV4MyCk=
=JHvb
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
"Here is the core arm64 queue for 4.5. As you might expect, the
Christmas break resulted in a number of patches not making the final
cut, so 4.6 is likely to be larger than usual. There's still some
useful stuff here, however, and it's detailed below.
The EFI changes have been Reviewed-by Matt and the memblock change got
an "OK" from akpm.
Summary:
- Support for a separate IRQ stack, although we haven't reduced the
size of our thread stack just yet since we don't have enough data
to determine a safe value
- Refactoring of our EFI initialisation and runtime code into
drivers/firmware/efi/ so that it can be reused by arch/arm/.
- Ftrace improvements when unwinding in the function graph tracer
- Document our silicon errata handling process
- Cache flushing optimisation when mapping executable pages
- Support for hugetlb mappings using the contiguous hint in the pte"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (45 commits)
arm64: head.S: use memset to clear BSS
efi: stub: define DISABLE_BRANCH_PROFILING for all architectures
arm64: entry: remove pointless SPSR mode check
arm64: mm: move pgd_cache initialisation to pgtable_cache_init
arm64: module: avoid undefined shift behavior in reloc_data()
arm64: module: fix relocation of movz instruction with negative immediate
arm64: traps: address fallout from printk -> pr_* conversion
arm64: ftrace: fix a stack tracer's output under function graph tracer
arm64: pass a task parameter to unwind_frame()
arm64: ftrace: modify a stack frame in a safe way
arm64: remove irq_count and do_softirq_own_stack()
arm64: hugetlb: add support for PTE contiguous bit
arm64: Use PoU cache instr for I/D coherency
arm64: Defer dcache flush in __cpu_copy_user_page
arm64: reduce stack use in irq_handler
arm64: mm: ensure that the zero page is visible to the page table walker
arm64: Documentation: add list of software workarounds for errata
arm64: mm: place __cpu_setup in .text
arm64: cmpxchg: Don't incldue linux/mmdebug.h
arm64: mm: fold alternatives into .init
...
The dmi_ver wasn't updated correctly before the dmi_decode method run
to save the uuid.
That resulted in "dmidecode -s system-uuid" and
/sys/class/dmi/id/product_uuid disagreeing. The latter was buggy and
this fixes it.
Reported-by: Federico Simoncelli <fsimonce@redhat.com>
Fixes: 9f9c9cbb60 ("drivers/firmware/dmi_scan.c: fetch dmi version from SMBIOS if it exists")
Fixes: 79bae42d51 ("dmi_scan: refactor dmi_scan_machine(), {smbios,dmi}_present()")
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
This moves the DISABLE_BRANCH_PROFILING define from the x86 specific
to the general CFLAGS definition for the stub. This fixes build errors
when building for arm64 with CONFIG_PROFILE_ALL_BRANCHES_ENABLED.
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Reported-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Switch to use a generic interface for issuing SMC/HVC based on ARM SMC
Calling Convention. Removes now the now unused psci-call.S.
Acked-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Adds helpers to do SMC and HVC based on ARM SMC Calling Convention.
CONFIG_HAVE_ARM_SMCCC is enabled for architectures that may support the
SMC or HVC instruction. It's the responsibility of the caller to know if
the SMC instruction is supported by the platform.
This patch doesn't provide an implementation of the declared functions.
Later patches will bring in implementations and set
CONFIG_HAVE_ARM_SMCCC for ARM and ARM64 respectively.
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds EFI stub support for the ARM Linux kernel.
The EFI stub operates similarly to the x86 and arm64 stubs: it is a
shim between the EFI firmware and the normal zImage entry point, and
sets up the environment that the zImage is expecting. This includes
optionally loading the initrd and device tree from the system partition
based on the kernel command line.
Signed-off-by: Roy Franz <roy.franz@linaro.org>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
This adds support to the kernel proper for booting via UEFI. It shares
most of the code with arm64, so this patch mostly just wires it up for
use with ARM.
Note that this does not include the EFI stub, it is added in a subsequent
patch.
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
This refactors the EFI init and runtime code that will be shared
between arm64 and ARM so that it can be built for both archs.
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This splits off the early EFI init and runtime code that
- discovers the EFI params and the memory map from the FDT, and installs
the memblocks and config tables.
- prepares and installs the EFI page tables so that UEFI Runtime Services
can be invoked at the virtual address installed by the stub.
This will allow it to be reused for 32-bit ARM.
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
As we've enabled multiplatform kernels on ARM, and greatly done away with
the contents under arch/arm/mach-*, there's still need for SoC-related
drivers to go somewhere.
Many of them go in through other driver trees, but we still have
drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code
that might be shared between ARM and ARM64 (or just in general makes
sense to not have under the architecture directory).
This branch contains mostly such code:
- Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to communicate
with power management blocks on these SoCs for use by clock, regulator and
bus frequency drivers.
- Allwinner Reduced Serial Bus driver, again used to communicate with PMICs.
- Drivers for ARM's SCPI (System Control Processor). Not to be confused with
PSCI (Power State Coordination Interface). SCPI is used to communicate with
the assistant embedded cores doing power management, and we have yet to see
how many of them will implement this for their hardware vs abstracting in
other ways (or not at all like in the past).
- To make confusion between SCPI and PSCI more likely, this release also
includes an update of PSCI to interface version 1.0.
- Rockchip support for power domains.
- A driver to talk to the firmware on Raspberry Pi.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dm+I
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"As we've enabled multiplatform kernels on ARM, and greatly done away
with the contents under arch/arm/mach-*, there's still need for
SoC-related drivers to go somewhere.
Many of them go in through other driver trees, but we still have
drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code
that might be shared between ARM and ARM64 (or just in general makes
sense to not have under the architecture directory).
This branch contains mostly such code:
- Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to
communicate with power management blocks on these SoCs for use by
clock, regulator and bus frequency drivers.
- Allwinner Reduced Serial Bus driver, again used to communicate with
PMICs.
- Drivers for ARM's SCPI (System Control Processor). Not to be
confused with PSCI (Power State Coordination Interface). SCPI is
used to communicate with the assistant embedded cores doing power
management, and we have yet to see how many of them will implement
this for their hardware vs abstracting in other ways (or not at all
like in the past).
- To make confusion between SCPI and PSCI more likely, this release
also includes an update of PSCI to interface version 1.0.
- Rockchip support for power domains.
- A driver to talk to the firmware on Raspberry Pi"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (57 commits)
soc: qcom: smd-rpm: Correct size of outgoing message
bus: sunxi-rsb: Add driver for Allwinner Reduced Serial Bus
bus: sunxi-rsb: Add Allwinner Reduced Serial Bus (RSB) controller bindings
ARM: bcm2835: add mutual inclusion protection
drivers: psci: make PSCI 1.0 functions initialization version dependent
dt-bindings: Correct paths in Rockchip power domains binding document
soc: rockchip: power-domain: don't try to print the clock name in error case
soc: qcom/smem: add HWSPINLOCK dependency
clk: berlin: add cpuclk
ARM: berlin: dts: add CLKID_CPU for BG2Q
ARM: bcm2835: Add the Raspberry Pi firmware driver
soc: qcom: smem: Move RPM message ram out of smem DT node
soc: qcom: smd-rpm: Correct the active vs sleep state flagging
soc: qcom: smd: delete unneeded of_node_put
firmware: qcom-scm: build for correct architecture level
soc: qcom: smd: Correct SMEM items for upper channels
qcom-scm: add missing prototype for qcom_scm_is_available()
qcom-scm: fix endianess issue in __qcom_scm_is_call_available
soc: qcom: smd: Reject send of too big packets
soc: qcom: smd: Handle big endian CPUs
...
backend drivers to be unloaded.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=liJx
-----END PGP SIGNATURE-----
Merge tag 'please-pull-pstore' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
Pull pstore updates from Tony Luck:
"Half dozen small cleanups plus change to allow pstore backend drivers
to be unloaded"
* tag 'please-pull-pstore' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
pstore: fix code comment to match code
efi-pstore: fix kernel-doc argument name
pstore: Fix return type of pstore_is_mounted()
pstore: add pstore unregister
pstore: add a helper function pstore_register_kmsg
pstore: add vmalloc error check
- "genirq: Introduce generic irq migration for cpu hotunplugged" patch
merged from tip/irq/for-arm to allow the arm64-specific part to be
upstreamed via the arm64 tree
- CPU feature detection reworked to cope with heterogeneous systems
where CPUs may not have exactly the same features. The features
reported by the kernel via internal data structures or ELF_HWCAP are
delayed until all the CPUs are up (and before user space starts)
- Support for 16KB pages, with the additional bonus of a 36-bit VA
space, though the latter only depending on EXPERT
- Implement native {relaxed, acquire, release} atomics for arm64
- New ASID allocation algorithm which avoids IPI on roll-over, together
with TLB invalidation optimisations (using local vs global where
feasible)
- KASan support for arm64
- EFI_STUB clean-up and isolation for the kernel proper (required by
KASan)
- copy_{to,from,in}_user optimisations (sharing the memcpy template)
- perf: moving arm64 to the arm32/64 shared PMU framework
- L1_CACHE_BYTES increased to 128 to accommodate Cavium hardware
- Support for the contiguous PTE hint on kernel mapping (16 consecutive
entries may be able to use a single TLB entry)
- Generic CONFIG_HZ now used on arm64
- defconfig updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=3six
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
- "genirq: Introduce generic irq migration for cpu hotunplugged" patch
merged from tip/irq/for-arm to allow the arm64-specific part to be
upstreamed via the arm64 tree
- CPU feature detection reworked to cope with heterogeneous systems
where CPUs may not have exactly the same features. The features
reported by the kernel via internal data structures or ELF_HWCAP are
delayed until all the CPUs are up (and before user space starts)
- Support for 16KB pages, with the additional bonus of a 36-bit VA
space, though the latter only depending on EXPERT
- Implement native {relaxed, acquire, release} atomics for arm64
- New ASID allocation algorithm which avoids IPI on roll-over, together
with TLB invalidation optimisations (using local vs global where
feasible)
- KASan support for arm64
- EFI_STUB clean-up and isolation for the kernel proper (required by
KASan)
- copy_{to,from,in}_user optimisations (sharing the memcpy template)
- perf: moving arm64 to the arm32/64 shared PMU framework
- L1_CACHE_BYTES increased to 128 to accommodate Cavium hardware
- Support for the contiguous PTE hint on kernel mapping (16 consecutive
entries may be able to use a single TLB entry)
- Generic CONFIG_HZ now used on arm64
- defconfig updates
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (91 commits)
arm64/efi: fix libstub build under CONFIG_MODVERSIONS
ARM64: Enable multi-core scheduler support by default
arm64/efi: move arm64 specific stub C code to libstub
arm64: page-align sections for DEBUG_RODATA
arm64: Fix build with CONFIG_ZONE_DMA=n
arm64: Fix compat register mappings
arm64: Increase the max granular size
arm64: remove bogus TASK_SIZE_64 check
arm64: make Timer Interrupt Frequency selectable
arm64/mm: use PAGE_ALIGNED instead of IS_ALIGNED
arm64: cachetype: fix definitions of ICACHEF_* flags
arm64: cpufeature: declare enable_cpu_capabilities as static
genirq: Make the cpuhotplug migration code less noisy
arm64: Constify hwcap name string arrays
arm64/kvm: Make use of the system wide safe values
arm64/debug: Make use of the system wide safe value
arm64: Move FP/ASIMD hwcap handling to common code
arm64/HWCAP: Use system wide safe values
arm64/capabilities: Make use of system wide safe value
arm64: Delay cpu feature capability checks
...
The first argument name in the kernel-doc argument list for
efi_pstore_scan_sysfs_enter() was slightly off. Fix it for the
kernel doc.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Now that we strictly forbid absolute relocations in libstub code,
make sure that we don't emit any when CONFIG_MODVERSIONS is enabled,
by stripping the kcrctab sections from the object file. This fixes
a build problem under CONFIG_MODVERSIONS=y.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Now that we added special handling to the C files in libstub, move
the one remaining arm64 specific EFI stub C file to libstub as
well, so that it gets the same treatment. This should prevent future
changes from resulting in binaries that may execute incorrectly in
UEFI context.
With efi-entry.S the only remaining EFI stub source file under
arch/arm64, we can also simplify the Makefile logic somewhat.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Commit:
0f96a99dab ("efi: Add "efi_fake_mem" boot option")
introduced the following warning message:
drivers/firmware/efi/fake_mem.c:186:20: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
new_memmap_phy was defined as a u64 value and cast to void*,
causing a int-to-pointer-cast warning on x86 32-bit builds.
However, since the void* type is inappropriate for a physical
address, the definition of struct efi_memory_map::phys_map has
been changed to phys_addr_t in the previous patch, and so the
cast can be dropped entirely.
This patch also changes the type of the "new_memmap_phy"
variable from "u64" to "phys_addr_t" to align with the types of
memblock_alloc() and struct efi_memory_map::phys_map.
Reported-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
[ Removed void* cast, updated commit log]
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kamezawa.hiroyu@jp.fujitsu.com
Cc: linux-efi@vger.kernel.org
Cc: matt.fleming@intel.com
Link: http://lkml.kernel.org/r/1445593697-1342-2-git-send-email-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We have been getting away with using a void* for the physical
address of the UEFI memory map, since, even on 32-bit platforms
with 64-bit physical addresses, no truncation takes place if the
memory map has been allocated by the firmware (which only uses
1:1 virtually addressable memory), which is usually the case.
However, commit:
0f96a99dab ("efi: Add "efi_fake_mem" boot option")
adds code that clones and modifies the UEFI memory map, and the
clone may live above 4 GB on 32-bit platforms.
This means our use of void* for struct efi_memory_map::phys_map has
graduated from 'incorrect but working' to 'incorrect and
broken', and we need to fix it.
So redefine struct efi_memory_map::phys_map as phys_addr_t, and
get rid of a bunch of casts that are now unneeded.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: izumi.taku@jp.fujitsu.com
Cc: kamezawa.hiroyu@jp.fujitsu.com
Cc: linux-efi@vger.kernel.org
Cc: matt.fleming@intel.com
Link: http://lkml.kernel.org/r/1445593697-1342-1-git-send-email-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This pull request contains the Raspberry Pi firmware driver, for communicating
with the VPU which has exclusive control of some of the peripherals.
Eric adds the actual firmware driver and Alexander fixes the header file which
was missing include guards.
* tag 'arm/soc/for-4.4/rpi-drivers' of https://github.com/Broadcom/stblinux:
ARM: bcm2835: add mutual inclusion protection
ARM: bcm2835: Add the Raspberry Pi firmware driver
Signed-off-by: Olof Johansson <olof@lixom.net>
The PSCI specifications [1] and the SMC calling convention mandate
that unimplemented functions ids must return NOT_SUPPORTED (0xffffffff)
if a function id is called but it is not implemented.
Consequently, PSCI 1.0 function ids that require the 1.0 PSCI_FEATURES
call to be initialized:
CPU_SUSPEND (psci_init_cpu_suspend())
SYSTEM_SUSPEND (psci_init_system_suspend())
call the PSCI_FEATURES function id independently of the detected
PSCI firmware version, since, if the PSCI_FEATURES function id is not
implemented, it must return NOT_SUPPORTED according to the PSCI
specifications, causing the initialization functions to fail as expected.
Some existing PSCI implementations (ie Qemu PSCI emulation), do not
comply with the SMC calling convention and fail if function ids that are
not implemented are called from the OS, causing boot failures.
To solve this issue, this patch adds code that checks the PSCI firmware
version before calling PSCI 1.0 initialization functions so that the
OS makes sure that it is calling 1.0 functions only if the firmware
version detected is 1.0 or greater, therefore avoiding PSCI calls
that are bound to fail and might cause system boot failures owing
to non-compliant PSCI firmware implementations.
[1] http://infocenter.arm.com/help/topic/com.arm.doc.den0022c/DEN0022C_Power_State_Coordination_Interface.pdf
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Tested-by: Kevin Hilman <khilman@kernel.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
features for arm/arm64 platforms:
- Lorenzo Pieralisi adds support for the PSCI_FEATURES call, manages
various 1.0 specifications updates (power state id and functions return
values) and provides PSCI v1.0 DT bindings
- Sudeep Holla implements PSCI v1.0 system suspend support to enable PSCI
based suspend-to-RAM
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=rYJ6
-----END PGP SIGNATURE-----
Merge tag 'firmware/psci-1.0' of git://git.kernel.org/pub/scm/linux/kernel/git/lpieralisi/linux into next/drivers
This pull request contains patches that enable PSCI 1.0 firmware
features for arm/arm64 platforms:
- Lorenzo Pieralisi adds support for the PSCI_FEATURES call, manages
various 1.0 specifications updates (power state id and functions return
values) and provides PSCI v1.0 DT bindings
- Sudeep Holla implements PSCI v1.0 system suspend support to enable PSCI
based suspend-to-RAM
* tag 'firmware/psci-1.0' of git://git.kernel.org/pub/scm/linux/kernel/git/lpieralisi/linux:
drivers: firmware: psci: add system suspend support
drivers: firmware: psci: define more generic PSCI_FN_NATIVE macro
drivers: firmware: psci: add PSCI v1.0 DT bindings
drivers: firmware: psci: add extended stateid power_state support
drivers: firmware: psci: add PSCI_FEATURES call
drivers: firmware: psci: move power_state handling to generic code
drivers: firmware: psci: add INVALID_ADDRESS return value
Signed-off-by: Olof Johansson <olof@lixom.net>
* Implement id_table driver matching in SMD
* Avoid NULL pointer exception on remove of SMEM
* Reorder SMEM/SMD configs
* Make qcom_smem_get() return a pointer
* Handle big endian CPUs correctly in SMEM
* Represent SMD channel layout in structures
* Use __iowrite32_copy() in SMD
* Remove use of VLAIs in SMD
* Handle big endian CPUs correctly in SMD/RPM
* Handle big endian CPUs corretly in SMD
* Reject sending SMD packets that are too large
* Fix endianness issue in SCM __qcom_scm_is_call_available
* Add missing prototype for qcom_scm_is_available()
* Correct SMEM items for upper channels
* Use architecture level to build SCM correctly
* Delete unneeded of_node_put in SMD
* Correct active/slep state flagging in SMD/RPM
* Move RPM message ram out of SMEM DT node
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=hprv
-----END PGP SIGNATURE-----
Merge tag 'qcom-soc-for-4.4' of git://codeaurora.org/quic/kernel/agross-msm into next/drivers
Pull "Qualcomm ARM Based SoC Updates for 4.4" from Andy Gross:
* Implement id_table driver matching in SMD
* Avoid NULL pointer exception on remove of SMEM
* Reorder SMEM/SMD configs
* Make qcom_smem_get() return a pointer
* Handle big endian CPUs correctly in SMEM
* Represent SMD channel layout in structures
* Use __iowrite32_copy() in SMD
* Remove use of VLAIs in SMD
* Handle big endian CPUs correctly in SMD/RPM
* Handle big endian CPUs corretly in SMD
* Reject sending SMD packets that are too large
* Fix endianness issue in SCM __qcom_scm_is_call_available
* Add missing prototype for qcom_scm_is_available()
* Correct SMEM items for upper channels
* Use architecture level to build SCM correctly
* Delete unneeded of_node_put in SMD
* Correct active/slep state flagging in SMD/RPM
* Move RPM message ram out of SMEM DT node
* tag 'qcom-soc-for-4.4' of git://codeaurora.org/quic/kernel/agross-msm:
soc: qcom: smem: Move RPM message ram out of smem DT node
soc: qcom: smd-rpm: Correct the active vs sleep state flagging
soc: qcom: smd: delete unneeded of_node_put
firmware: qcom-scm: build for correct architecture level
soc: qcom: smd: Correct SMEM items for upper channels
qcom-scm: add missing prototype for qcom_scm_is_available()
qcom-scm: fix endianess issue in __qcom_scm_is_call_available
soc: qcom: smd: Reject send of too big packets
soc: qcom: smd: Handle big endian CPUs
soc: qcom: smd_rpm: Handle big endian CPUs
soc: qcom: smd: Remove use of VLAIS
soc: qcom: smd: Use __iowrite32_copy() instead of open-coding it
soc: qcom: smd: Represent channel layout in structures
soc: qcom: smem: Handle big endian CPUs
soc: qcom: Make qcom_smem_get() return a pointer
soc: qcom: Reorder SMEM/SMD configs
soc: qcom: smem: Avoid NULL pointer exception on remove
soc: qcom: smd: Implement id_table driver matching
This gives us a function for making mailbox property channel requests
of the firmware, which is most notable in that it will let us get and
set clock rates.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
The ".arch_extension sec" directive is only available on ARMv6 or higher,
so if we enable the SCM driver while building a kernel for an older CPU,
we get a build error:
/tmp/ccUyhMOY.s:130: Error: selected processor does not support ARM mode `smc #0'
/tmp/ccUyhMOY.s:216: Error: selected processor does not support ARM mode `smc #0'
/tmp/ccUyhMOY.s:373: Error: selected processor does not support ARM mode `smc #0'
make[4]: *** [drivers/firmware/qcom_scm-32.o] Error 1
This changes the Makefile so we pass the ARMv7 architecture level both
for the check and for the actual compilation of the scm driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andy Gross <agross@codeaurora.org>
It adds support for the following features provided by SCP firmware
using different subsystems in Linux:
1. SCPI mailbox protocol driver which using mailbox framework
2. Clocks provided by SCP using clock framework
3. CPU DVFS(cpufreq) using existing arm-big-little driver
4. SCPI based sensors including temperature sensors
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9u+p
-----END PGP SIGNATURE-----
Merge tag 'arm-scpi-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/drivers
Merge "ARM System Control and Power Interface(SCPI) support" from Sudeep Holla
It adds support for the following features provided by SCP firmware
using different subsystems in Linux:
1. SCPI mailbox protocol driver which using mailbox framework
2. Clocks provided by SCP using clock framework
3. CPU DVFS(cpufreq) using existing arm-big-little driver
4. SCPI based sensors including temperature sensors
* tag 'arm-scpi-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
hwmon: Support thermal zones registration for SCP temperature sensors
hwmon: Support sensors exported via ARM SCP interface
firmware: arm_scpi: Extend to support sensors
Documentation: add DT bindings for ARM SCPI sensors
cpufreq: arm_big_little: add SCPI interface driver
clk: scpi: add support for cpufreq virtual device
clk: add support for clocks provided by SCP(System Control Processor)
firmware: add support for ARM System Control and Power Interface(SCPI) protocol
Documentation: add DT binding for ARM System Control and Power Interface(SCPI) protocol
non-modular by ripping out the module_* code since Kconfig doesn't
allow it to be built as a module anyway - Paul Gortmaker
* Make the x86 efi=debug kernel parameter, which enables EFI debug
code and output, generic and usable by arm64 - Leif Lindholm
* Add support to the x86 EFI boot stub for 64-bit Graphics Output
Protocol frame buffer addresses - Matt Fleming
* Detect when the UEFI v2.5 EFI_PROPERTIES_TABLE feature is enabled
in the firmware and set an efi.flags bit so the kernel knows when
it can apply more strict runtime mapping attributes - Ard Biesheuvel
* Auto-load the efi-pstore module on EFI systems, just like we
currently do for the efivars module - Ben Hutchings
* Add "efi_fake_mem" kernel parameter which allows the system's EFI
memory map to be updated with additional attributes for specific
memory ranges. This is useful for testing the kernel code that handles
the EFI_MEMORY_MORE_RELIABLE memmap bit even if your firmware
doesn't include support - Taku Izumi
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1Oee
-----END PGP SIGNATURE-----
Merge tag 'efi-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mfleming/efi into core/efi
Pull v4.4 EFI updates from Matt Fleming:
- Make the EFI System Resource Table (ESRT) driver explicitly
non-modular by ripping out the module_* code since Kconfig doesn't
allow it to be built as a module anyway. (Paul Gortmaker)
- Make the x86 efi=debug kernel parameter, which enables EFI debug
code and output, generic and usable by arm64. (Leif Lindholm)
- Add support to the x86 EFI boot stub for 64-bit Graphics Output
Protocol frame buffer addresses. (Matt Fleming)
- Detect when the UEFI v2.5 EFI_PROPERTIES_TABLE feature is enabled
in the firmware and set an efi.flags bit so the kernel knows when
it can apply more strict runtime mapping attributes - Ard Biesheuvel
- Auto-load the efi-pstore module on EFI systems, just like we
currently do for the efivars module. (Ben Hutchings)
- Add "efi_fake_mem" kernel parameter which allows the system's EFI
memory map to be updated with additional attributes for specific
memory ranges. This is useful for testing the kernel code that handles
the EFI_MEMORY_MORE_RELIABLE memmap bit even if your firmware
doesn't include support. (Taku Izumi)
Note: there is a semantic conflict between the following two commits:
8a53554e12 ("x86/efi: Fix multiple GOP device support")
ae2ee627dc ("efifb: Add support for 64-bit frame buffer addresses")
I fixed up the interaction in the merge commit, changing the type of
current_fb_base from u32 to u64.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch adds arch specific code for kernel address sanitizer
(see Documentation/kasan.txt).
1/8 of kernel addresses reserved for shadow memory. There was no
big enough hole for this, so virtual addresses for shadow were
stolen from vmalloc area.
At early boot stage the whole shadow region populated with just
one physical page (kasan_zero_page). Later, this page reused
as readonly zero shadow for some memory that KASan currently
don't track (vmalloc).
After mapping the physical memory, pages for shadow memory are
allocated and mapped.
Functions like memset/memmove/memcpy do a lot of memory accesses.
If bad pointer passed to one of these function it is important
to catch this. Compiler's instrumentation cannot do this since
these functions are written in assembly.
KASan replaces memory functions with manually instrumented variants.
Original functions declared as weak symbols so strong definitions
in mm/kasan/kasan.c could replace them. Original functions have aliases
with '__' prefix in name, so we could call non-instrumented variant
if needed.
Some files built without kasan instrumentation (e.g. mm/slub.c).
Original mem* function replaced (via #define) with prefixed variants
to disable memory access checks for such files.
Signed-off-by: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Since arm64 does not use a builtin decompressor, the EFI stub is built
into the kernel proper. So far, this has been working fine, but actually,
since the stub is in fact a PE/COFF relocatable binary that is executed
at an unknown offset in the 1:1 mapping provided by the UEFI firmware, we
should not be seamlessly sharing code with the kernel proper, which is a
position dependent executable linked at a high virtual offset.
So instead, separate the contents of libstub and its dependencies, by
putting them into their own namespace by prefixing all of its symbols
with __efistub. This way, we have tight control over what parts of the
kernel proper are referenced by the stub.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
With the stub to kernel interface being promoted to a proper interface
so that other agents than the stub can boot the kernel proper in EFI
mode, we can remove the linux,uefi-stub-kern-ver field, considering
that its original purpose was to prevent this from happening in the
first place.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch introduces new boot option named "efi_fake_mem".
By specifying this parameter, you can add arbitrary attribute
to specific memory range.
This is useful for debugging of Address Range Mirroring feature.
For example, if "efi_fake_mem=2G@4G:0x10000,2G@0x10a0000000:0x10000"
is specified, the original (firmware provided) EFI memmap will be
updated so that the specified memory regions have
EFI_MEMORY_MORE_RELIABLE attribute (0x10000):
<original>
efi: mem36: [Conventional Memory| | | | | | |WB|WT|WC|UC] range=[0x0000000100000000-0x00000020a0000000) (129536MB)
<updated>
efi: mem36: [Conventional Memory| |MR| | | | |WB|WT|WC|UC] range=[0x0000000100000000-0x0000000180000000) (2048MB)
efi: mem37: [Conventional Memory| | | | | | |WB|WT|WC|UC] range=[0x0000000180000000-0x00000010a0000000) (61952MB)
efi: mem38: [Conventional Memory| |MR| | | | |WB|WT|WC|UC] range=[0x00000010a0000000-0x0000001120000000) (2048MB)
efi: mem39: [Conventional Memory| | | | | | |WB|WT|WC|UC] range=[0x0000001120000000-0x00000020a0000000) (63488MB)
And you will find that the following message is output:
efi: Memory: 4096M/131455M mirrored memory
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Xishi Qiu <qiuxishi@huawei.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
efi-pstore should be auto-loaded on EFI systems, same as efivars.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Lee, Chun-Yi <jlee@suse.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
UEFI v2.5 introduces a runtime memory protection feature that splits
PE/COFF runtime images into separate code and data regions. Since this
may require special handling by the OS, allocate a EFI_xxx bit to
keep track of whether this feature is currently active or not.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Version 2.5 of the UEFI spec introduces a new configuration table
called the 'EFI Properties table'. Currently, it is only used to
convey whether the Memory Protection feature is enabled, which splits
PE/COFF images into separate code and data memory regions.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Acked-by: Dave Young <dyoung@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
UEFI spec 2.5 introduces new Memory Attribute Definition named
EFI_MEMORY_MORE_RELIABLE. This patch adds this new attribute
support to efi_md_typeattr_format().
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Xishi Qiu <qiuxishi@huawei.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
As we now have a common debug infrastructure between core and arm64 efi,
drop the bit of the interface passing verbose output flags around.
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Mark Salter <msalter@redhat.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
fed6cefe3b ("x86/efi: Add a "debug" option to the efi= cmdline")
adds the DBG flag, but does so for x86 only. Move this early param
parsing to core code.
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Mark Salter <msalter@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
The Kconfig for this driver is currently hidden with:
config EFI_ESRT
bool
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We leave some tags like MODULE_AUTHOR for documentation purposes.
We don't replace module.h with init.h since the file already has that.
Cc: Peter Jones <pjones@redhat.com>
Cc: linux-efi@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Guenter reports that commit:
7bf793115d ("efi, x86: Rearrange efi_mem_attributes()")
breaks the IA64 compilation with the following error:
drivers/built-in.o: In function `efi_mem_attributes': (.text+0xde962): undefined reference to `memmap'
Instead of using the (rather poorly named) global variable
'memmap' which doesn't exist on IA64, use efi.memmap which
points to the 'memmap' object on x86 and arm64 and which is NULL
for IA64.
The fact that efi.memmap is NULL for IA64 is OK because IA64
provides its own implementation of efi_mem_attributes().
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Jonathan Zhang <zjzhang@codeaurora.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/20151003222607.GA2682@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
ARM System Control Processor (SCP) provides an API to query and use
the sensors available in the system. Extend the SCPI driver to support
sensor messages.
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
PSCI v1.0 introduces a new API called PSCI_SYSTEM_SUSPEND. This API
provides the mechanism by which the calling OS can request entry into
the deepest possible system sleep state.
It meets all the necessary preconditions for entering suspend to RAM
state in Linux. This patch adds support for PSCI_SYSTEM_SUSPEND in psci
firmware and registers a psci system suspend operation to implement the
suspend-to-RAM(s2r) in a generic way on all the platforms implementing
PSCI.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
This patch replaces the definition and usage of PSCI_0_2_FN_NATIVE with
the new and more generic macro PSCI_FN_NATIVE that can be used with any
version. This will be useful for the new features introduced in PSCIv1.0
and for any future revisions.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
PSCI 1.0 is designed to be fully compliant to the PSCI 0.2
specification, with minor differences that are described in the
PSCI specification.
In particular, PSCI v1.0 augments the specification with a new
power_state format (extended stateid - probeable through the
PSCI_FEATURES call), changes some function return codes and
functions usage requirements wrt PSCI 0.2. These changes mean
that 1.0 vs 0.2 compliancy should be enforced through a DT
compatible string that allows firmware to specify 1.0 only
compliancy so that older kernels are prevented from using
PSCI 1.0 FW implementations in a non-compatible way (eg by
calling a 1.0 FW implementation and expecting 0.2 behaviour).
This patch adds PSCI 1.0 DT bindings and related compatible
string.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Jisheng Zhang <jszhang@marvell.com>
Cc: Mark Rutland <mark.rutland@arm.com>
PSCI v1.0 augmented the power_state parameter format specification
(extended stateid) and introduced a way to probe it through the
PSCI_FEATURES interface.
This patch implements code that detects the power_state format at
run-time through the PSCI_FEATURES interface, so that the power_state
argument can be properly detected and validated in the kernel according
to the information provided through firmware.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Jisheng Zhang <jszhang@marvell.com>
Cc: Mark Rutland <mark.rutland@arm.com>
PSCI v1.0 introduces a PSCI_FEATURES call that allows to probe for
features related to a specific function identifier.
This patch adds PSCI_FEATURES support to the PSCI firmware layer.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Jisheng Zhang <jszhang@marvell.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Functions implemented on arm64 to check if a power_state parameter
is valid and if the power_state implies context loss are not
arm64 specific and should be moved to generic code so that they
can be reused on arm systems too.
This patch moves the functions handling the power_state parameter
to generic PSCI firmware layer code.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Jisheng Zhang <jszhang@marvell.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
