On CML boards with the RT5682 headset codec and RT1011 speaker
amplifier, the platform firmware exposes three ACPI HIDs
(10EC5682, 10EC1011 and MX98357A). The last HID is a mistake in
DSDT tables, which causes the wrong machine driver to be loaded.
This patch changes the key used to identify boards and changes the
order of entries in the table to load the correct machine driver.
The order does matter and should not be modified to work-around this
firmware issue.
Signed-off-by: Amery Song <chao.song@intel.com>
Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191210004854.16845-9-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Due to firmware manifest/signature differences, we have to use
different firmware names, so split CNL machine table in three (CNL,
CFL, CML).
The CFL table is currently empty since all known platforms use
HDaudio, but let's plan ahead.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191111222901.19892-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add match for CML m/c with RT1011 and RT5682
Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Signed-off-by: Sathya Prakash M R <sathya.prakash.m.r@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191101171847.26767-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As shown in diffstat and logs, it was again a busy development
cycle at this time, too. The most significant changes are still
on-going refactoring / modernization works for ASoC core and
drivers, but there are lots of other changes as well. Here we go,
some highlights below:
ASoC:
- Quite lots of cleanup / refactoring of ASoC core and APIs;
most of them are systematic, but also including cleanups and
modernization
- A bulk of updates for some ASoC platforms, Freescale, sunxi and
Intel SST/SOF
- Initial support for Sound Open Firmware on i.MX8
- Removal of deprecated w90x900 and nuc900 drivers
- New support for Cirrus Logic CS47L15 and CS47L92, Freescale i.MX
7ULP and 8MQ, Meson G12A and NXP UDA1334
USB-audio:
- More validations of descriptor units for hardening against bugs
reported by fuzzers
- PCM device assignment workaround for a past call-order change
- Scarlett Gen2 mixer interface, a few more more quirks
HD-audio:
- Support for audio component with AMD/ATI and Nvidia HDMI codecs
- Clean up HD-audio core and remove indirect access ops for Intel SOF
- DMIC detection at probe; it would make systems automatically falling
back to SST/SOF driver on devices that need DMIC handling.
Needs a new Kconfig to set, and beware that it's still new and a bit
experimental
FireWire:
- Lots of code refactoring and cleanups
-----BEGIN PGP SIGNATURE-----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=/+1Q
-----END PGP SIGNATURE-----
Merge tag 'sound-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"As shown in diffstat and logs, it was again a busy development cycle
at this time, too. The most significant changes are still on-going
refactoring / modernization works for ASoC core and drivers, but there
are lots of other changes as well. Here we go, some highlights below:
ASoC:
- Quite a lot of cleanup / refactoring of ASoC core and APIs; most of
them are systematic, but also including cleanups and modernization
- A bulk of updates for some ASoC platforms, Freescale, sunxi and
Intel SST/SOF
- Initial support for Sound Open Firmware on i.MX8
- Removal of deprecated w90x900 and nuc900 drivers
- New support for Cirrus Logic CS47L15 and CS47L92, Freescale i.MX
7ULP and 8MQ, Meson G12A and NXP UDA1334
USB-audio:
- More validations of descriptor units for hardening against bugs
reported by fuzzers
- PCM device assignment workaround for a past call-order change
- Scarlett Gen2 mixer interface, a few more more quirks
HD-audio:
- Support for audio component with AMD/ATI and Nvidia HDMI codecs
- Clean up HD-audio core and remove indirect access ops for Intel SOF
- DMIC detection at probe; it would make systems automatically
falling back to SST/SOF driver on devices that need DMIC handling.
Needs a new Kconfig to set, and beware that it's still new and a
bit experimental
FireWire:
- Lots of code refactoring and cleanups"
* tag 'sound-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (521 commits)
ASoC: sdm845: remove unneeded semicolon
ASoC: fsl_sai: Implement set_bclk_ratio
ASoC: dmaengine: Replace strncpy() with strscpy_pad() for pcm->name
ASoC: wcd9335: remove redundant use of ret variable
ALSA: firewire-tascam: check intermediate state of clock status and retry
ALSA: firewire-tascam: handle error code when getting current source of clock
ASoC: hdmi-codec: Add an op to set callback function for plug event
ASoC: rt5677: keep analog power register at SND_SOC_BIAS_OFF
ASoC: rt5677: Remove magic number register writes
ASoC: soc-core: self contained soc_unbind_aux_dev()
ASoC: soc-core: add soc_unbind_aux_dev()
ASoC: soc-core: self contained soc_bind_aux_dev()
ASoC: soc-core: move soc_probe_link_dais() next to soc_remove_link_dais()
ASoC: soc-core: self contained soc_probe_link_dais()
ASoC: soc-core: add new soc_link_init()
ASoC: soc-core: move soc_probe_dai() next to soc_remove_dai()
ASoC: soc-core: self contained soc_remove_link_dais()
ASoC: soc-core: self contained soc_remove_link_components()
ASoC: soc-core: self contained soc_probe_link_components()
ASoC: rt1308: make array pd static const, makes object smaller
...
Apart from Haswell machines, all other devices have their private data
set to snd_soc_acpi_mach instance.
Changes for HSW/ BDW boards introduced with series:
https://patchwork.kernel.org/cover/10782035/
added support for dai_link platform_name adjustments within card probe
routines. These take for granted private_data points to
snd_soc_acpi_mach whereas for Haswell, it's sst_pdata instead. Change
private context of platform_device - representing machine board - to
address this.
Fixes: e87055d732 ("ASoC: Intel: haswell: platform name fixup support")
Fixes: 7e40ddcf97 ("ASoC: Intel: bdw-rt5677: platform name fixup support")
Fixes: 2d067b2807 ("ASoC: Intel: broadwell: platform name fixup support")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20190822113616.22702-2-cezary.rojewski@intel.com
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If ipc->ops.reply_msg_match is NULL, we may end up using uninitialized
mask value.
reported by smatch:
sound/soc/intel/common/sst-ipc.c:266 sst_ipc_reply_find_msg() error: uninitialized symbol 'mask'.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@intel.com>
Link: https://lore.kernel.org/r/20190827141712.21015-3-amadeuszx.slawinski@linux.intel.com
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
There are no upstream machine drivers just yet so just add dummy table
for compilation in nocodec-mode.
Signed-off-by: Pan Xiuli <xiuli.pan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190815155749.29304-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
reuse and add Cometlake support with:
SSP0 for DA7219 headphone codec
SSP1 for MAX98357a speaker amp codec
Signed-off-by: Mac Chiang <mac.chiang@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/1565851909-13825-1-git-send-email-mac.chiang@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
struct ipc_message contains fields: header, tx_data and tx_size which
represent TX i.e. request while RX is represented by rx_data and rx_size
with reply's header equivalent missing.
Reply header may contain some vital information including, but not
limited to, received payload size. Some IPCs have entire payload found
within RX header instead. Content and value of said header is context
dependent and may vary between firmware versions and target platform.
Current model does not allow such IPCs to function at all.
Rather than appending yet another parameter to an already long list of
such for sst_ipc_tx_message_XXXs, declare message container in form of
struct sst_ipc_message and add them to parent's ipc_message declaration.
Align haswell, baytrail and skylake with updated request-reply model and
modify their reply processing functions to save RX header within message
container. Despite the range of changes, status quo is achieved.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20190723144341.21339-2-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix some typo to have the filaname given in a comment match the real name
of the file.
Some 'acpi' have erroneously been written 'apci'
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20190725053523.16542-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Skylake driver is divided into two modules:
- snd_soc_skl
- snd_soc_skl_ipc
and nothing would be wrong if not for the fact that both cannot exist
without one another. IPC module is not some kind of extension, as it is
the case for snd_hda_ext_core which is separated from snd_hda_core -
legacy hda interface. It's as much core Skylake module as snd_soc_skl
is.
Statement backed up by existence of circular dependency between this
two. To eliminate said problem, struct skl_sst has been created. From
that very momment, Skylake has been plagued by header errors (incomplete
structs, unknown references etc.) whenever something new is to be added
or code is cleaned up.
As this design is being corrected, struct skl_sst is no longer needed,
so combine it with struct skl. To avoid ambiguity when searching for skl
stuff (struct skl *skl) it has also been renamed to skl_dev.
No functional changes.
Signed-off-by: Piotr Maziarz <piotrx.maziarz@intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20190723145854.8527-2-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
rx_data and rx_bytes present for tx_wait_done are optional parameters.
If not provided, function should not attempt to copy received data.
This change fixes memcpy NULL pointer dereference issue occurring when
optional rx_data is NULL while received message size is non-zero.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
you might feel like a deja vu to receive a bulk of changes at rc5,
and it happens again; we've got a collection of fixes for ASoC.
Most of fixes are targeted for the newly merged SOF (Sound Open
Firmware) stuff and the relevant fixes for Intel platforms.
Other than that, there are a few regression fixes for the recent
ASoC core changes and HD-audio quirk, as well as a couple of
FireWire fixes and for other ASoC codecs.
-----BEGIN PGP SIGNATURE-----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=9U0L
-----END PGP SIGNATURE-----
Merge tag 'sound-5.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"It might feel like deja vu to receive a bulk of changes at rc5, and it
happens again; we've got a collection of fixes for ASoC. Most of fixes
are targeted for the newly merged SOF (Sound Open Firmware) stuff and
the relevant fixes for Intel platforms.
Other than that, there are a few regression fixes for the recent ASoC
core changes and HD-audio quirk, as well as a couple of FireWire fixes
and for other ASoC codecs"
* tag 'sound-5.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (54 commits)
Revert "ALSA: hda/realtek - Improve the headset mic for Acer Aspire laptops"
ALSA: ice1712: Check correct return value to snd_i2c_sendbytes (EWS/DMX 6Fire)
ALSA: oxfw: allow PCM capture for Stanton SCS.1m
ALSA: firewire-motu: fix destruction of data for isochronous resources
ASoC: Intel: sst: fix kmalloc call with wrong flags
ASoC: core: Fix deadlock in snd_soc_instantiate_card()
SoC: rt274: Fix internal jack assignment in set_jack callback
ALSA: hdac: fix memory release for SST and SOF drivers
ASoC: SOF: Intel: hda: use the defined ppcap functions
ASoC: core: move DAI pre-links initiation to snd_soc_instantiate_card
ASoC: Intel: cht_bsw_rt5672: fix kernel oops with platform_name override
ASoC: Intel: cht_bsw_nau8824: fix kernel oops with platform_name override
ASoC: Intel: bytcht_es8316: fix kernel oops with platform_name override
ASoC: Intel: cht_bsw_max98090: fix kernel oops with platform_name override
ASoC: sun4i-i2s: Add offset to RX channel select
ASoC: sun4i-i2s: Fix sun8i tx channel offset mask
ASoC: max98090: remove 24-bit format support if RJ is 0
ASoC: da7219: Fix build error without CONFIG_I2C
ASoC: SOF: Intel: hda: Fix COMPILE_TEST build error
ASoC: SOF: fix DSP oops definitions in FW ABI
...
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 263 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.208660670@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This tablet has an incorrect acpi identifier just like
Thinkpad10 tablet, which is why it is trying to load the RT5640 driver
instead of the RT5762 driver. The RT5640 driver, on the other hand, checks
the hardware ID, so no driver are loaded during boot. This fix resolves to
load the RT5672 driver on this tablet during boot. It also provides the
correct IO configuration, like the jack detect mode 3, for 1.8V pullup. I
would like to thank Pierre-Louis Bossart for helping with this patch.
Signed-off-by: Kovács Tamás <kepszlok@zohomail.eu>
Signed-off-by: Mark Brown <broonie@kernel.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have duplicated code in multiple locations (atom, machine drivers,
SOF) to detect Baytrail, Cherrytrail and other SOCs. This is not very
elegant, and introduces dependencies on CONFIG_X86 that prevent
COMPILE_TEST from working.
Add common helpers to provide same functionality in a cleaner
way. This will also help support the DMI-based quirks being introduced
to handle SOF/SST autodetection.
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is an implementation of a machine driver needed for Conexant
CX2072X codec on Intel Baytrail and Cherrytrail platforms. The
current patch is based on the initial work by Pierre-Louis Bossart and
the other Intel machine drivers.
The jack detection support (driven via the standard GPIO) was added on
top of the original work.
Tested with ASUS E200HA laptop.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=115531
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The selection order of m/c in match table is corrected
to use common codec as last in the list.
Signed-off-by: Sathya Prakash M R <sathya.prakash.m.r@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The machine driver is a generic machine driver for SOF with rt5682
codec. it currently supports BYT/CHT/ICL/CML. Depending on the SOC
hdmi/speaker and DMIC support are added dynamically.
Only add information related to SOF since the machine driver was
only tested with SOF.
Signed-off-by: Sathya Prakash M R <sathya.prakash.m.r@intel.com>
Signed-off-by: Bard liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently in sst_dsp_new() if we get an error return from sst_dma_new()
we just print an error message and then still complete the function
successfully. This means that we are trying to run without sst->dma
properly set up, which will result in NULL pointer dereference when
sst->dma is later used. This was happening for me in
sst_dsp_dma_get_channel():
struct sst_dma *dma = dsp->dma;
...
dma->ch = dma_request_channel(mask, dma_chan_filter, dsp);
This resulted in:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000018
IP: sst_dsp_dma_get_channel+0x4f/0x125 [snd_soc_sst_firmware]
Fix this by adding proper error handling for the case where we fail to
set up DMA.
This change only affects Haswell and Broadwell systems. Baytrail
systems explicilty opt-out of DMA via sst->pdata->resindex_dma_base
being set to -1.
Signed-off-by: Ross Zwisler <zwisler@google.com>
Cc: stable@vger.kernel.org
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds glk_rt5682_max98357a_i2s machine driver entry into
machine table. Both Skylake and SOF platform drivers can use this
machine drivers.
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch enables the reuse of kbl_da7219_max98927 machine driver to
support max98373. The same machine driver is modified for cases where one
amplifier is swapped out with another. Most of the changes are about
renaming the codec and codec_dai names, with minor differences due to
support for 24 bits in one case and 16 in the other.
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This field was never used, let's remove it
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This field was never used, let's remove it
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This field was never used, let's remove it
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This field was never used, let's remove it
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This field was never used, let's remove it
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This field was never used, let's remove it
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This field was never used, let's remove it
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Prefix is now handled in the code. This allows for default and
alternate paths, and more flexibility for OEMs and distros
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Prefix is now handled in the code. This allows for default and
alternate paths, and more flexibility for OEMs and distros
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Prefix is now handled in the code. This allows for default and
alternate paths, and more flexibility for OEMs and distros
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Prefix is now handled in the code. This allows for default and
alternate paths, and more flexibility for OEMs and distros
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Prefix is now handled in the code. This allows for default and
alternate paths, and more flexibility for OEMs and distros
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Prefix is now handled in the code. This allows for default and
alternate paths, and more flexibility for OEMs and distros
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Prefix is now handled in the code. This allows for default and
alternate paths, and more flexibility for OEMs and distros
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Prefix is now handled in the code. This allows for default and
alternate paths, and more flexibility for OEMs and distros
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Point of View TAB-P1006W-232 (v1.0) tablet uses 10EC5640 as
ACPI HID, but it has a rt5651 codec add a quirk for this.
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some BYTCR devices use an ES8316 codec, add an ACPI match table entry
for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The new Dell IoT platform uses kabylake + alc3277 codec, and alc3277
shares the driver with the codec rt5660, here we generate a new
machine driver based on kbl_da7219_max98357a.
The audio design on this IoT platform is as below:
- Intel kabylake platform
- connect the codec ALC3277 via SSP0
- line-out and line-in with Micbias jacks
- line-out mute control and jack detection of line-out and line-in
- two HDMI ports with audio capability
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Entry needed for ICL RVP w/ RT274
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For some reason the RVP/LeafHill SSDT exposes an INT34C3 ID which is
used on other boards to point to the TDF8532 amplifier. Yay BIOS.
Add a DMI-quirk to ignore this ID and check for other valid machine
driver descriptors.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add firmware/topology information for APL RVP
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bard liao <bard.liao@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DMA API does its own zone decisions based on the coherent_dma_mask.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds da7219_max98927 machine driver entry into
machine table
Signed-off-by: Mac Chiang <mac.chiang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Thinkpad 8 tablet uses 10EC5640 as ACPI HID, but it has a rt5670 codec
add a quirk for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Expose a table containing machine driver information for HDAudio-based
platforms handled by ASoC on Intel hardware.
We only set constant values that are valid across multiple
platforms. The firmware name used by the DSP will be set dynamically
for each platform.
The table is made of a single entry for now, if we need more
complicated set-up where HDAudio is mixed with ACPI-enumerated devices
(I2C, SoundWire) then we'd expect the differentiation to be handled
through information provided by the BIOS (as done for KBL
Chromebooks).
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Also add these typos to spelling.txt so checkpatch.pl will look for them.
Link: http://lkml.kernel.org/r/88af06b9de34d870cb0afc46cfd24e0458be2575.1529471371.git.fthain@telegraphics.com.au
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sst_dma_new and sst_dma_free are not used in any other file and don't
have a prototype. Move to static functions and remove
EXPORT_SYMBOL_GPL statement.
Reported by sparse warnings.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Somehow I missed the Nau8824 support which was added in 4.17. Oops
Fixes: 4f722a6a73 ("ASoC: Intel: common: rename 'reef' to 'sof' in ACPI matching table")
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Align with firmware tools, no functionality change
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are two commercially-available Broadwell platforms based on I2S
(Dell XPS13 and 'Samus' Pixel 2015 Chromebook).
Fix a copy/paste issue to allow each platform to enable different
features if needed when SOF is enabled
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
While we are at it, add entries for machine drivers that are used on
SOF-based platforms. The drivers will be submitted upstream after the
core SOF patches, but there's no harm in adding these references now.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
No functionality change for Skylake driver, add relevant names needed
by SOF for BXT/APL, GLK and CNL.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
No functionality change, just move to common tables to make it easier
to deal with SOF and share the same machine drivers - as done
previously for BYT/CHT/HSW/BDW.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Create sound card with NAU88L24 codec in Intel Cherryview-based platforms,
Cherrytrail and Braswell.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
No need to read the register again if the value read has already matched
the target during the loop. So remove the second shim read.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The MODULE_DESCRIPTION() macro is only available when including
the linux/module.h header. Apparently this is included indirectly
from sst-firmware.c in some configurations, but not in others:
sound/soc/intel/common/sst-firmware.c:1278:20: error: expected declaration specifiers or '...' before string constant
MODULE_DESCRIPTION("Intel SST Firmware Loader");
^~~~~~~~~~~~~~~~~~~~~~~~~~~
sound/soc/intel/common/sst-firmware.c:1279:16: error: expected declaration specifiers or '...' before string constant
This adds the missing include line.
Fixes: a395bdd6b2 ("ASoC: intel: Fix sst-dsp dependency on dw stuff")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare for SOF integration, no functional change
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
First step of cleaning, move all tables to soc-acpi-intel-match module.
The tables remain in separate files per platform to keep them
manageable. Skylake+ platforms are still handled elsewhere since
there is no conflict with SOF for now, but this will have to be
handled at a later point.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Before we add new fields for SOF support, move to C99 syntax
as done for atom/sst and legacy hsw/bdw code
No functional change
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ACPI support is not specific to the Intel/SST driver. Move the enumeration
and matching code which is not hardware-dependent to sound/soc and rename
relevant sst_acpi_ structures and functions with snd_soc_acpi_ prefix
soc-acpi.h is protected by a #ifndef __LINUX_SND_SOC_ACPI_H for
consistency with all other SoC .h files:
grep -L __LINUX include/sound/soc* | wc -l
0
grep __LINUX include/sound/soc* | wc -l
14
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The pointer dma_dev_name is assigned but never read, it is redundant
and can therefore be removed.
Cleans up clang warning:
sound/soc/intel/common/sst-firmware.c:288:3: warning: Value stored to
'dma_dev_name' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SRAM address and memory window size differ for different platforms.
So add members to sst_addr structure and initialize them in the
respective dsp_init().
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use quirk function to select the correct machine driver
by checking all codecs instead of only one based on quirk data.
Signed-off-by: Naveen M <naveen.m@intel.com>
Signed-off-by: Harsha Priya <harshapriya.n@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sst_acpi_mach has a quirk field to handle board specific quirks.
Patch moves quirk call to sst_acpi_find_machine() instead of calling
it in respective driver
Signed-off-by: Naveen M <naveen.m@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Create a helper function to search for a matching machine
based on HID. No functional change
Signed-off-by: Naveen M <naveen.m@intel.com>
Signed-off-by: Harsha Priya <harshapriya.n@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Poll implementation is not quite accurate, especially for smaller
values of timeout or timeout values close to the actual timeout needed
Use jiffies to set the timeout value and time_before() to get the
accurate time. So update the dsp register poll implementation to
provide accurate timeout using jiffies.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The usage pattern of kthread worker in Intel SST drivers can be
replaced gracefully with the normal workqueue, which is more light-
weight and easier to manage in general. Let's do it.
While in the replacement, move the schedule_work() call inside the
spinlock for excluding the race, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a new common routine to extract a package exposed by a
device indexed with the HID value. The functionality is
implemented without assumptions on the package type or
structure to allow for reuse. The caller is responsible for
defining the name and allocating structures to store the
results, ACPICA will complain in case of type mismatches
or buffer size issues.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the DSP is in low power mode, it needs to be woken up by a "wake" IPC
to set it into the D0 state before we can send any other IPC command.
The call flow is that the driver calls sst_ipc_tx_message_wait() to send any
IPC and this call checks if the device is in low power mode and in that
case we need to send the wake IPC.
So add a new IPC nopm variant which can be called from driver and
doesn't check for power state (as we already know that) and avoids
circular dependency of again checking power state.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some controllers support power modes which can't communicate using IPC.
So add a callback to check and wake DSP before sending IPC and then put
to sleep if it is in these power modes.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Kernel source files need not include <linux/kconfig.h> explicitly
because the top Makefile forces to include it with:
-include $(srctree)/include/linux/kconfig.h
This commit removes explicit includes except the following:
* arch/s390/include/asm/facilities_src.h
* tools/testing/radix-tree/linux/kernel.h
These two are used for host programs.
Link: http://lkml.kernel.org/r/1473656164-11929-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A good practice is to prefix the names of functions by the name
of the subsystem.
The kthread worker API is a mix of classic kthreads and workqueues. Each
worker has a dedicated kthread. It runs a generic function that process
queued works. It is implemented as part of the kthread subsystem.
This patch renames the existing kthread worker API to use
the corresponding name from the workqueues API prefixed by
kthread_:
__init_kthread_worker() -> __kthread_init_worker()
init_kthread_worker() -> kthread_init_worker()
init_kthread_work() -> kthread_init_work()
insert_kthread_work() -> kthread_insert_work()
queue_kthread_work() -> kthread_queue_work()
flush_kthread_work() -> kthread_flush_work()
flush_kthread_worker() -> kthread_flush_worker()
Note that the names of DEFINE_KTHREAD_WORK*() macros stay
as they are. It is common that the "DEFINE_" prefix has
precedence over the subsystem names.
Note that INIT() macros and init() functions use different
naming scheme. There is no good solution. There are several
reasons for this solution:
+ "init" in the function names stands for the verb "initialize"
aka "initialize worker". While "INIT" in the macro names
stands for the noun "INITIALIZER" aka "worker initializer".
+ INIT() macros are used only in DEFINE() macros
+ init() functions are used close to the other kthread()
functions. It looks much better if all the functions
use the same scheme.
+ There will be also kthread_destroy_worker() that will
be used close to kthread_cancel_work(). It is related
to the init() function. Again it looks better if all
functions use the same naming scheme.
+ there are several precedents for such init() function
names, e.g. amd_iommu_init_device(), free_area_init_node(),
jump_label_init_type(), regmap_init_mmio_clk(),
+ It is not an argument but it was inconsistent even before.
[arnd@arndb.de: fix linux-next merge conflict]
Link: http://lkml.kernel.org/r/20160908135724.1311726-1-arnd@arndb.de
Link: http://lkml.kernel.org/r/1470754545-17632-3-git-send-email-pmladek@suse.com
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Borislav Petkov <bp@suse.de>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is used by the Chromebook Pixel 2015.
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Dylan Reid <dgreid@chromium.org>
[john@metanate.com:
- forward-port driver from Chromium OS 3.14 tree to master
- remove wake on voice function that isn't supported by upstream rt5677
driver
- remote owner assignment in platform_driver (Evan McClain)
- convert to devm_snd_soc_register_card (Evan McClain)
- add a full copyright header based on module license and Chromium OS
Git history
]
Signed-off-by: John Keeping <john@metanate.com>
Tested-by: Genki Marshall <genki@genki.is>
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The recent commit [a92ea59b74: ASoC: Intel: sst: only select
sst-firmware when DW DMAC is built-in] introduced more strict kconfig
dependency (depends on DW_DMAC_CORE=y) for avoiding the build failures
due to dependency messes in intel-sst. This makes, however, it
impossible to use this driver with the modularized systems,
i.e. typically on Linux distros.
The problem addressed in the commit above is that sst_dsp_new() and
sst_dsp_free() includes the firmware init / finish that call dw_*()
functions. Thus building it as built-in with DW_DMAC_CORE module
results in the missing symbols.
However, these sst_dsp functions are basically called only from the
drivers that depend on DW_DMAC_CORE already. That is, once when these
functions are split out, the rest can be independent from dw stuff.
This patch attempts to solve the issue by the following:
- Split sst-dsp stuff into two modules: snd-soc-sst-dsp and
snd-soc-sst-firmware.
- Move sst_dsp_new() and sst_dsp_free() to the latter module so that
the former module can be independent from DW_DMAC_CORE.
- Add a new kconfig SND_SOC_INTEL_SST_FIRMWARE to select the latter
module by machine drivers.
One only remaining pitfall is that each machine driver has to select
SND_SOC_INTEL_SST_FIRMWARE carefully depending on DW_DMAC_CORE.
This can't be done cleanly due to the restriction of the current
kbuild.
Bugzilla: https://bugzilla.opensuse.org/show_bug.cgi?id=988117
Fixes: a92ea59b74 ('ASoC: Intel: sst: only select sst-firmware when DW DMAC is built-in')
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Surface 3 is CHT based device which shows up with RT5645 codec. But the
BIOS reports ACPI ID as 5640!
To solve this, add a DMI overide for cht-5640 machine.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=98001
Signed-off-by: Sachin Mokashi <sachinx.mokashi@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For consistency with other log statements, change dev_info to dev_dbg
for a kernel print which is frequently printed by the driver.
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This function stub should have been 'static' in the original patch
so that multiple uses of the header file (in different drivers)
will not cause multiple function definitions.
sound/soc/intel/boards/built-in.o: In function `sst_acpi_find_name_from_hid':
(.text+0x560): multiple definition of `sst_acpi_find_name_from_hid'
sound/soc/intel/atom/built-in.o:(.text+0x10610): first defined here
../scripts/Makefile.build:369: recipe for target 'sound/soc/intel/built-in.o' failed
Fixes: f17131a93f: add function stub when ACPI is not enabled
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This time was again a relatively calm development cycle; most of
updates are about drivers, and no radical changes are seen in any
core code. Here are some highlights:
ALSA core:
- Continued hardening of ALSA hrtimer
- A few leak fixes in timer interface
- Fix poll error handling in PCM and compress
- Add error propagation in compress API
- Removal of dead rtctimer driver
HD-audio:
- Native ELD notify support for i915 HDMI
- Realtek ALC234 & co support
- Code refactoring to standardize chmap support
- Continued development for SKL HDMI core support
Firewire:
- Apply delayed card registration to all drivers
- Improved / stabilized the handling of PCM stream start / stop
- Add tracepoints to dump a part of isochronous packet data
- Fixed incoming/outgoing packet parameter usages
- Add support for M-Audio profire series
USB-audio:
- Fixes for UAC2 clock source
- SS+ support
- Workaround for oft-seen repeated sample rate read errors
ASoC:
- Further slow progress on the topology code
- Substantial updates and improvements for the da7219, es8328,
fsl-ssi, Intel and rcar drivers.
- Compress error handling in WM ADSP driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=QsAc
-----END PGP SIGNATURE-----
Merge tag 'sound-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This time was again a relatively calm development cycle; most of
updates are about drivers, and no radical changes are seen in any core
code. Here are some highlights:
ALSA core:
- Continued hardening of ALSA hrtimer
- A few leak fixes in timer interface
- Fix poll error handling in PCM and compress
- Add error propagation in compress API
- Removal of dead rtctimer driver
HD-audio:
- Native ELD notify support for i915 HDMI
- Realtek ALC234 & co support
- Code refactoring to standardize chmap support
- Continued development for SKL HDMI core support
Firewire:
- Apply delayed card registration to all drivers
- Improved / stabilized the handling of PCM stream start / stop
- Add tracepoints to dump a part of isochronous packet data
- Fixed incoming/outgoing packet parameter usages
- Add support for M-Audio profire series
USB-audio:
- Fixes for UAC2 clock source
- SS+ support
- Workaround for oft-seen repeated sample rate read errors
ASoC:
- Further slow progress on the topology code
- Substantial updates and improvements for the da7219, es8328,
fsl-ssi, Intel and rcar drivers.
- Compress error handling in WM ADSP driver"
* tag 'sound-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (177 commits)
ALSA: firewire-lib: change a member of event structure to suppress sparse wanings to bool type
sound: oss: Use setup_timer and mod_timer.
ASoC: hdac_hdmi: Remove the unused 'timeout' variable
ASoC: fsl_ssi: Fix channel slipping on capture (or playback) restart in full duplex.
ASoC: fsl_ssi: Fix channel slipping in Playback at startup
ASoC: fsl_ssi: Fix samples being dropped at Playback startup
ASoC: fsl_ssi: Save a dev reference for dev_err() purpose.
ASoC: fsl_ssi: The IPG/5 limitation concerns the bitclk, not the sysclk.
ASoC: fsl_ssi: Real hardware channels max number is 32
ASoC: pcm5102a: Add support for PCM5102A codec
ASoC: hdac_hdmi: add link management
ASoC: Intel: Skylake: add link management
ALSA: hdac: add link pm and ref counting
ALSA: au88x0: Fix zero clear of stream->resources
ASoC: rt298: Add DMI match for Broxton-P reference platform
ASoC: rt298: fix null deref on acpi driver data
ASoC: dapm: deprecate MICBIAS widget type
ALSA: firewire-lib: drop skip argument from helper functions to queue a packet
ALSA: firewire-lib: add context information to tracepoints
ALSA: firewire-lib: permit to flush queued packets only in process context for better PCM period granularity
...
We pass struct dw_dma_chip to dw_dma_probe() anyway, thus we may use it to
pass a platform data as well.
While here, constify the source of the platform data.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add function stub for "sst_acpi_find_name_from_hid()"
when CONFIG_ACPI is not enabled so that the driver will build
successfully. This fixes the following build errors:
(loadable module)
ERROR: "sst_acpi_find_name_from_hid" [sound/soc/intel/boards/snd-soc-sst-bytcr-rt5640.ko] undefined!
(or built-in)
bytcr_rt5640.c:(.text+0x26fc52): undefined reference to `sst_acpi_find_name_from_hid'
Reported-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Broxton uses HDA DMA so needs to keep dmab in the driver context
so add it
Signed-off-by: GuruprasadX Pawse <guruprasadx.pawse@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
BIOS vendors sometimes declare multiple devices in the DSDT
table that all refer to the same HID. This is not very smart
but not illegal as long as only one device reports present with
the _STA method. The ACPI subsystem tracks each device with an
extension, e.g. 10EC5640:00 and 10EC5640:01
In the ASoC machine driver, the DAI codec name needs to refer to the
ACPI device that reported present, e.g. "i2c-10EC5640:01". The
extension will vary depending on how the BIOS is written and which
ACPI device is activated.
This patch adds a translation function that provides the codec
name from the ACPI HID to avoid any hard-coded values in the
machine driver.
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
