The brcmstb host driver does the same host registration and bus scanning
calls as pci_host_probe, so let's use it instead.
Link: https://lore.kernel.org/r/20200522234832.954484-5-robh@kernel.org
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Cc: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-rpi-kernel@lists.infradead.org
There's no need to create a temporary resource list and then splice it to
struct pci_host_bridge.windows list. Just use pci_host_bridge.windows
directly. The necessary clean-up is already handled by the PCI core.
Link: https://lore.kernel.org/r/20200522234832.954484-4-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Will Deacon <will@kernel.org>
Lots of define are actually already defined in pci_regs.h, directly use
the standard defines.
Link: https://lore.kernel.org/r/20200615210608.21469-13-ansuelsmth@gmail.com
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Some SoC based on ipq8064/5 needs to be limited to pci GEN1 speed due to
some hardware limitations. Add support for speed setting defined by the
max-link-speed binding. If not defined the max speed is set to GEN2 by
default.
Link: https://lore.kernel.org/r/20200615210608.21469-12-ansuelsmth@gmail.com
Signed-off-by: Sham Muthayyan <smuthayy@codeaurora.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Ipq8064-v2 have tx term offset set to 0. Introduce this variant to permit
different offset based on the revision.
Link: https://lore.kernel.org/r/20200615210608.21469-10-ansuelsmth@gmail.com
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Add tx term offset support to pcie qcom driver need in some revision of
the ipq806x SoC. Ipq8064 needs tx term offset set to 7.
Link: https://lore.kernel.org/r/20200615210608.21469-9-ansuelsmth@gmail.com
Fixes: 82a823833f ("PCI: qcom: Add Qualcomm PCIe controller driver")
Signed-off-by: Sham Muthayyan <smuthayy@codeaurora.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: stable@vger.kernel.org # v4.5+
Set some specific value for Tx De-Emphasis, Tx Swing and Rx equalization
needed on some ipq8064 based device (Netgear R7800 for example). Without
this the system locks on kernel load.
Link: https://lore.kernel.org/r/20200615210608.21469-8-ansuelsmth@gmail.com
Fixes: 82a823833f ("PCI: qcom: Add Qualcomm PCIe controller driver")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: stable@vger.kernel.org # v4.5+
Rework 2.1.0 revision to use bulk clk api and fix missing assert on
reset_control_deassert error.
Link: https://lore.kernel.org/r/20200615210608.21469-7-ansuelsmth@gmail.com
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
The deinit issues reset_control_assert for PCI twice and does not contain
phy reset.
Link: https://lore.kernel.org/r/20200615210608.21469-4-ansuelsmth@gmail.com
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Aux and Ref clk are missing in PCIe qcom driver. Add support for this
optional clks for ipq8064/apq8064 SoC.
Link: https://lore.kernel.org/r/20200615210608.21469-2-ansuelsmth@gmail.com
Fixes: 82a823833f ("PCI: qcom: Add Qualcomm PCIe controller driver")
Signed-off-by: Sham Muthayyan <smuthayy@codeaurora.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Most callers of config read do not check for return value. But most of the
ones that do, checks for error indication in 'val' variable.
This patch updates error handling in advk_pcie_rd_conf() function. If PIO
transfer fails then 'val' variable is set to 0xffffffff which indicates
failture.
Link: https://lore.kernel.org/r/20200528162604.GA323482@bjorn-Precision-5520
Link: https://lore.kernel.org/r/20200601130315.18895-1-pali@kernel.org
Reported-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code, thus a matching decrement is needed on
the error handling path to keep the counter balanced.
Link: https://lore.kernel.org/r/20200707055000.9453-1-dinghao.liu@zju.edu.cn
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
pm_runtime_get_sync() increments the runtime PM usage counter even
it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Link: https://lore.kernel.org/r/20200520090253.2761-1-dinghao.liu@zju.edu.cn
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
pm_runtime_get_sync() increments the runtime PM usage counter even
it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Link: https://lore.kernel.org/r/20200520084756.31620-1-dinghao.liu@zju.edu.cn
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
VMD device 28C0 natively assists guest passthrough of the VMD endpoint
through the use of shadow registers that provide Host Physical Addresses
to correctly assign bridge windows. These shadow registers are only
available if VMD config space register 0x70, bit 1 is set.
In order to support this mode in existing VMD devices which don't
natively support the shadow register, it was decided that the hypervisor
could offer the shadow registers in a vendor-specific PCI capability.
QEMU has been modified to create this vendor-specific capability and
supply the shadow membar registers for VMDs which don't natively support
this feature. This patch adds this mode and updates the supported device
list to allow this feature to be used on these VMDs.
Link: https://lore.kernel.org/r/20200528030240.16024-4-jonathan.derrick@intel.com
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
There's no need to create a temporary resource list and then splice it to
struct pci_host_bridge.windows list. Just use pci_host_bridge.windows
directly. The necessary clean-up is already handled by the PCI core.
Link: https://lore.kernel.org/r/20200522234832.954484-3-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Jason Cooper <jason@lakedaemon.net>
There's no need to create a temporary resource list and then splice it to
struct pci_host_bridge.windows list. Just use pci_host_bridge.windows
directly. The necessary clean-up is already handled by the PCI core.
Link: https://lore.kernel.org/r/20200522234832.954484-2-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Tom Joseph <tjoseph@cadence.com>
Replace http:// links with https:// links. This reduces the likelihood of
man-in-the-middle attacks when developers open these links.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
[bhelgaas: also update samsung.com links, drop sourceforge link]
Link: https://lore.kernel.org/r/20200627103050.71712-1-grandmaster@al2klimov.de
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
- Release resource in probe failure path (Wei Hu)
- Retry PCI bus D0 entry if device state is invalid (Wei Hu)
- Use struct_size() to help avoid type mistakes (Gustavo A. R. Silva)
* remotes/lorenzo/pci/hv:
PCI: hv: Use struct_size() helper
PCI: hv: Retry PCI bus D0 entry on invalid device state
PCI: hv: Fix the PCI HyperV probe failure path to release resource properly
- Constify struct pci_ecam_ops (Rob Herring)
- Support building as modules (Rob Herring)
- Eliminate wrappers for pci_host_common_probe() by using DT match table
data (Rob Herring)
* remotes/lorenzo/pci/host-generic:
PCI: host-generic: Eliminate pci_host_common_probe wrappers
PCI: host-generic: Support building as modules
PCI: Constify struct pci_ecam_ops
# Conflicts:
# drivers/pci/controller/dwc/pcie-hisi.c
- Deprecate 'cdns,max-outbound-regions' and 'cdns,no-bar-match-nbits'
bindings in favor of deriving them from 'ranges' and 'dma-ranges'
(Kishon Vijay Abraham I)
- Read Vendor and Device ID as 32 bits (not 16) from DT (Kishon Vijay
Abraham I)
* remotes/lorenzo/pci/cadence:
PCI: cadence: Fix to read 32-bit Vendor ID/Device ID property from DT
PCI: cadence: Remove "cdns,max-outbound-regions" DT property
dt-bindings: PCI: cadence: Deprecate inbound/outbound specific bindings
- Train link immediately after enabling link training to avoid issues
with Compex WLE900VX and Turris MOX devices (Pali Rohár)
- Remove ASPM config and let the PCI core do it (Pali Rohár)
- Interpret zero 'max-link-speed' value as invalid (Pali Rohár)
- Respect the 'max-link-speed' property and improve link training (Marek
Behún)
- Issue PERST via GPIO (Pali Rohár)
- Add PHY support (Marek Behún)
- Use standard PCIe capability macros (Pali Rohár)
- Document new 'max-link-speed', 'phys', and 'reset-gpios' properties
(Marek Behún)
* remotes/lorenzo/pci/aardvark:
dt-bindings: PCI: aardvark: Describe new properties
PCI: aardvark: Replace custom macros by standard linux/pci_regs.h macros
PCI: aardvark: Add PHY support
PCI: aardvark: Add FIXME comment for PCIE_CORE_CMD_STATUS_REG access
PCI: aardvark: Issue PERST via GPIO
PCI: aardvark: Improve link training
PCI: of: Zero max-link-speed value is invalid
PCI: aardvark: Don't blindly enable ASPM L0s and don't write to read-only register
PCI: aardvark: Train link immediately after enabling training
- Clarify that platform_get_irq() should never return 0 (Bjorn Helgaas)
- Check for platform_get_irq() failure consistently (Bjorn Helgaas)
- Replace zero-length array with flexible-array (Gustavo A. R. Silva)
- Unify pcie_find_root_port() and pci_find_pcie_root_port() (Yicong Yang)
- Quirk Intel C620 MROMs, which have non-BARs in BAR locations (Xiaochun
Lee)
- Fix pcie_pme_resume() and pcie_pme_remove() kernel-doc (Jay Fang)
- Rename _DSM constants to align with spec (Krzysztof Wilczyński)
* pci/misc:
PCI: Rename _DSM constants to align with spec
PCI/PME: Fix kernel-doc of pcie_pme_resume() and pcie_pme_remove()
x86/PCI: Mark Intel C620 MROMs as having non-compliant BARs
PCI: Unify pcie_find_root_port() and pci_find_pcie_root_port()
PCI: Replace zero-length array with flexible-array
PCI: Check for platform_get_irq() failure consistently
driver core: platform: Clarify that IRQ 0 is invalid
Add driver for the Socionext UniPhier Pro5 SoC endpoint controller.
This controller is based on the DesignWare PCIe core.
And add "host" to existing controller descriontions for the host controller
in Kconfig.
Link: https://lore.kernel.org/r/1589457801-12796-3-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEIbPD0id6easf0xsudhRwX5BBoF4FAl7WhbkTHHdlaS5saXVA
a2VybmVsLm9yZwAKCRB2FHBfkEGgXlUnB/0R8dBVSeRfNmyJaadBWKFc/LffwKLD
CQ8PVv22ffkCaEYV2tpnhS6NmkERLNdson4Uo02tVUsjOJ4CrWHTn7aKqYWZyA+O
qv/PiD9TBXJVYMVP2kkyaJlK5KoqeAWBr2kM16tT0cxQmlhE7g0Xo2wU9vhRbU+4
i4F0jffe4lWps65TK392CsPr6UEv1HSel191Py5zLzYqChT+L8WfahmBt3chhsV5
TIUJYQvBwxecFRla7yo+4sUn37ZfcTqD1hCWSr0zs4psW0ge7d80kuaNZS+EqxND
fGm3Bp1BlUuDKsJ/D+AaHLCR47PUZ9t9iMDjZS/ovYglLFwi+h3tAV+W
=LwVR
-----END PGP SIGNATURE-----
Merge tag 'hyperv-next-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyper-v updates from Wei Liu:
- a series from Andrea to support channel reassignment
- a series from Vitaly to clean up Vmbus message handling
- a series from Michael to clean up and augment hyperv-tlfs.h
- patches from Andy to clean up GUID usage in Hyper-V code
- a few other misc patches
* tag 'hyperv-next-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux: (29 commits)
Drivers: hv: vmbus: Resolve more races involving init_vp_index()
Drivers: hv: vmbus: Resolve race between init_vp_index() and CPU hotplug
vmbus: Replace zero-length array with flexible-array
Driver: hv: vmbus: drop a no long applicable comment
hyper-v: Switch to use UUID types directly
hyper-v: Replace open-coded variant of %*phN specifier
hyper-v: Supply GUID pointer to printf() like functions
hyper-v: Use UUID API for exporting the GUID (part 2)
asm-generic/hyperv: Add definitions for Get/SetVpRegister hypercalls
x86/hyperv: Split hyperv-tlfs.h into arch dependent and independent files
x86/hyperv: Remove HV_PROCESSOR_POWER_STATE #defines
KVM: x86: hyperv: Remove duplicate definitions of Reference TSC Page
drivers: hv: remove redundant assignment to pointer primary_channel
scsi: storvsc: Re-init stor_chns when a channel interrupt is re-assigned
Drivers: hv: vmbus: Introduce the CHANNELMSG_MODIFYCHANNEL message type
Drivers: hv: vmbus: Synchronize init_vp_index() vs. CPU hotplug
Drivers: hv: vmbus: Remove the unused HV_LOCALIZED channel affinity logic
PCI: hv: Prepare hv_compose_msi_msg() for the VMBus-channel-interrupt-to-vCPU reassignment functionality
Drivers: hv: vmbus: Use a spin lock for synchronizing channel scheduling vs. channel removal
hv_utils: Always execute the fcopy and vss callbacks in a tasklet
...
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Also, call pm_runtime_disable() when pm_runtime_get_sync() returns
an error code.
Link: https://lore.kernel.org/r/20200521024709.2368-1-dinghao.liu@zju.edu.cn
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Versions of VMD with the Host Physical Address shadow register use this
register to calculate the bus address offset needed to do guest
passthrough of the domain. This register shadows the Host Physical
Address registers including the resource type bits. After calculating
the offset, the extra resource type bits lead to the VMD resources being
over-provisioned at the front and under-provisioned at the back.
Example:
pci 10000:80:02.0: reg 0x10: [mem 0xf801fffc-0xf803fffb 64bit]
Expected:
pci 10000:80:02.0: reg 0x10: [mem 0xf8020000-0xf803ffff 64bit]
If other devices are mapped in the over-provisioned front, it could lead
to resource conflict issues with VMD or those devices.
Link: https://lore.kernel.org/r/20200528030240.16024-3-jonathan.derrick@intel.com
Fixes: a1a3017013 ("PCI: vmd: Fix shadow offsets to reflect spec changes")
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Link: https://lore.kernel.org/r/20200521031355.7022-1-dinghao.liu@zju.edu.cn
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Vidya Sagar <vidyas@nvidia.com>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct hv_dr_state {
...
struct hv_pcidev_description func[];
};
struct pci_bus_relations {
...
struct pci_function_description func[];
} __packed;
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.
So, replace the following forms:
offsetof(struct hv_dr_state, func) +
(sizeof(struct hv_pcidev_description) *
(relations->device_count))
offsetof(struct pci_bus_relations, func) +
(sizeof(struct pci_function_description) *
(bus_rel->device_count))
with:
struct_size(dr, func, relations->device_count)
and
struct_size(bus_rel, func, bus_rel->device_count)
respectively.
Link: https://lore.kernel.org/r/20200525164319.GA13596@embeddedor
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Wei Liu <wei.liu@kernel.org>
This controller can be found on Loongson-2K SoC, Loongson-3
systems with RS780E/LS7A PCH.
The RS780E part of code was previously located at
arch/mips/pci/ops-loongson3.c and now it can use generic PCI
driver implementation.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
No functional change. Get "struct pcie_port *" from private data
pointer of "struct irq_domain" in dw_pcie_irq_domain_free() to make
it look similar to how "struct pcie_port *" is obtained in
dw_pcie_irq_domain_alloc()
Link: https://lore.kernel.org/r/20191220100550.777-1-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
The vim3l board does not work with a standard PCIe switch (ASM1184e),
spitting all kind of errors - hinting at HW misconfiguration (no link,
port enumeration issues, etc).
According to the the Synopsys DWC PCIe Reference Manual, in the section
dedicated to the PLCR register, bit 7 is described (FAST_LINK_MODE) as:
"Sets all internal timers to fast mode for simulation purposes."
it is sound to set this bit from a simulation perspective, but on actual
silicon, which expects timers to have a nominal value, it is not.
Make sure the FAST_LINK_MODE bit is cleared when configuring the RC
to solve this problem.
Link: https://lore.kernel.org/r/20200429164230.309922-1-maz@kernel.org
Fixes: 9c0ef6d34f ("PCI: amlogic: Add the Amlogic Meson PCIe controller driver")
Signed-off-by: Marc Zyngier <maz@kernel.org>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
On a system that uses the internal DWC MSI widget, I get this
warning from debugfs when CONFIG_GENERIC_IRQ_DEBUGFS is selected:
debugfs: File ':soc:pcie@fc000000' in directory 'domains' already present!
This is due to the fact that the DWC MSI code tries to register two
IRQ domains for the same firmware node, without telling the low
level code how to distinguish them (by setting a bus token). This
further confuses debugfs which tries to create corresponding
files for each domain.
Fix it by tagging the inner domain as DOMAIN_BUS_NEXUS, which is
the closest thing we have as to "generic MSI".
Link: https://lore.kernel.org/r/20200501113921.366597-1-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
platform_get_resource() may fail and return NULL, so we had better
check its return value to avoid a NULL pointer dereference a bit later
in the code. Fix it to use devm_platform_ioremap_resource_byname()
instead of calling platform_get_resource_byname() and devm_ioremap().
Link: https://lore.kernel.org/r/20200429015027.134485-1-weiyongjun1@huawei.com
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Fix the following sparse warning:
drivers/pci/controller/dwc/pcie-intel-gw.c:456:5: warning: symbol
'intel_pcie_cpu_addr' was not declared. Should it be static?
Link: https://lore.kernel.org/r/20200415084953.6533-1-yanaijie@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Function dw_pcie_prog_outbound_atu_unroll() does not program the upper
32-bit ATU limit register. Since ATU programming functions limit the
size of the translated region to 4GB by using a u32 size parameter,
these issues may combine into undefined behavior for resource sizes
with non-zero upper 32-bits.
For example, a 128GB address space starting at physical CPU address of
0x2000000000 with size of 0x2000000000 needs the following values
programmed into the lower and upper 32-bit limit registers:
0x3fffffff in the upper 32-bit limit register
0xffffffff in the lower 32-bit limit register
Currently, only the lower 32-bit limit register is programmed with a
value of 0xffffffff but the upper 32-bit limit register is not being
programmed. As a result, the upper 32-bit limit register remains at its
default value after reset of 0x0.
These issues may combine to produce undefined behavior since the ATU
limit address may be lower than the ATU base address. Programming the
upper ATU limit address register prevents such undefined behavior despite
the region size getting truncated due to the 32-bit size limit.
Link: https://lore.kernel.org/r/1585785493-23210-1-git-send-email-alan.mikhak@sifive.com
Signed-off-by: Alan Mikhak <alan.mikhak@sifive.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
R-Car PCIe controller has support to map multiple memory regions for
mapping the outbound memory in local system also the controller limits
single allocation for each region (that is, once a chunk is used from the
region it cannot be used to allocate a new one). This features inspires to
add support for handling multiple memory bases in endpoint framework.
With this patch pci_epc_mem_init() initializes address space for endpoint
controller which support single window and pci_epc_multi_mem_init()
initializes multiple windows supported by endpoint controller.
Link: https://lore.kernel.org/r/1588854799-13710-6-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
The PCI Bus Binding specification (IEEE Std 1275-1994 Revision 2.1 [1])
defines both Vendor ID and Device ID to be 32-bits. Fix
pcie-cadence-host.c driver to read 32-bit Vendor ID and Device ID
properties from device tree.
[1] -> https://www.devicetree.org/open-firmware/bindings/pci/pci2_1.pdf
Link: https://lore.kernel.org/r/20200508130646.23939-4-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tom Joseph <tjoseph@cadence.com>
"cdns,max-outbound-regions" device tree property provides the
maximum number of outbound regions supported by the Host PCIe
controller. However the outbound regions are configured based
on what is populated in the "ranges" DT property.
Avoid using two properties for configuring outbound regions and
use only "ranges" property instead.
Link: https://lore.kernel.org/r/20200508130646.23939-3-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tom Joseph <tjoseph@cadence.com>
PCI-E capability macros are already defined in linux/pci_regs.h.
Remove their reimplementation in pcie-aardvark.
Link: https://lore.kernel.org/r/20200430080625.26070-9-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
With recent proposed changes for U-Boot it is possible that bootloader
won't initialize the PHY for this controller (currently the PHY is
initialized regardless whether PCI is used in U-Boot, but with these
proposed changes the PHY is initialized only on request).
Since the mvebu-a3700-comphy driver by Miquèl Raynal supports enabling
PCIe PHY, and since Linux' functionality should be independent on what
bootloader did, add code for enabling generic PHY if found in device OF
node.
The mvebu-a3700-comphy driver does PHY powering via SMC calls to ARM
Trusted Firmware. The corresponding code in ARM Trusted Firmware skips
one register write which U-Boot does not: step 7 ("Enable TX"), see [1].
Instead ARM Trusted Firmware expects PCIe driver to do this step,
probably because the register is in PCIe controller address space,
instead of PHY address space. We therefore add this step into the
advk_pcie_setup_hw function.
[1] https://git.trustedfirmware.org/TF-A/trusted-firmware-a.git/tree/drivers/marvell/comphy/phy-comphy-3700.c?h=v2.3-rc2#n836
Link: https://lore.kernel.org/r/20200430080625.26070-8-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Miquèl Raynal <miquel.raynal@bootlin.com>
This register is applicable only when the controller is configured for
Endpoint mode, which is not the case for the current version of this
driver.
Attempting to remove this code though caused some ath10k cards to stop
working, so for some unknown reason it is needed here.
This should be investigated and a comment explaining this should be put
before the code, so we add a FIXME comment for now.
Link: https://lore.kernel.org/r/20200430080625.26070-7-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add support for issuing PERST via GPIO specified in 'reset-gpios'
property (as described in PCI device tree bindings).
Some buggy cards (e.g. Compex WLE900VX or WLE1216) are not detected
after reboot when PERST is not issued during driver initialization.
If bootloader already enabled link training then issuing PERST has no
effect for some buggy cards (e.g. Compex WLE900VX) and these cards are
not detected. We therefore clear the LINK_TRAINING_EN register before.
It was observed that Compex WLE900VX card needs to be in PERST reset
for at least 10ms if bootloader enabled link training.
Tested on Turris MOX.
Link: https://lore.kernel.org/r/20200430080625.26070-6-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Currently the aardvark driver trains link in PCIe gen2 mode. This may
cause some buggy gen1 cards (such as Compex WLE900VX) to be unstable or
even not detected. Moreover when ASPM code tries to retrain link second
time, these cards may stop responding and link goes down. If gen1 is
used this does not happen.
Unconditionally forcing gen1 is not a good solution since it may have
performance impact on gen2 cards.
To overcome this, read 'max-link-speed' property (as defined in PCI
device tree bindings) and use this as max gen mode. Then iteratively try
link training at this mode or lower until successful. After successful
link training choose final controller gen based on Negotiated Link Speed
from Link Status register, which should match card speed.
Link: https://lore.kernel.org/r/20200430080625.26070-5-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Trying to change Link Status register does not have any effect as this
is a read-only register. Trying to overwrite bits for Negotiated Link
Width does not make sense.
In future proper change of link width can be done via Lane Count Select
bits in PCIe Control 0 register.
Trying to unconditionally enable ASPM L0s via ASPM Control bits in Link
Control register is wrong. There should be at least some detection if
endpoint supports L0s as isn't mandatory.
Moreover ASPM Control bits in Link Control register are controlled by
pcie/aspm.c code which sets it according to system ASPM settings,
immediately after aardvark driver probes. So setting these bits by
aardvark driver has no long running effect.
Remove code which touches ASPM L0s bits from this driver and let
kernel's ASPM implementation to set ASPM state properly.
Some users are reporting issues that this code is problematic for some
Intel wifi cards and removing it fixes them, see e.g.:
https://bugzilla.kernel.org/show_bug.cgi?id=196339
If problems with Intel wifi cards occur even after this commit, then
pcie/aspm.c code could be modified / hooked to not enable ASPM L0s state
for affected problematic cards.
Link: https://lore.kernel.org/r/20200430080625.26070-3-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Adding even 100ms (PCI_PM_D3COLD_WAIT) delay between enabling link
training and starting link training causes detection issues with some
buggy cards (such as Compex WLE900VX).
Move the code which enables link training immediately before the one
which starts link traning.
This fixes detection issues of Compex WLE900VX card on Turris MOX after
cold boot.
Link: https://lore.kernel.org/r/20200430080625.26070-2-pali@kernel.org
Fixes: f4c7d053d7 ("PCI: aardvark: Wait for endpoint to be ready...")
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
xHCI's PCI fixup, run at the end of pcie-brcmstb's probe, depends on
RPi4's VideoCore firmware interface to be up and running. It's possible
for both initializations to race, so make sure it's available prior to
starting.
Link: https://lore.kernel.org/r/20200505161318.26200-4-nsaenzjulienne@suse.de
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
The platform_get_irq*() interfaces return either a negative error number or
a valid IRQ. 0 is not a valid return value, so check for "< 0" to detect
failure as recommended by the function documentation.
On failure, return the error number from platform_get_irq*() instead of
making up a new one.
Link: https://lore.kernel.org/r/cover.1583952275.git.amanharitsh123@gmail.com
[bhelgaas: commit log, squash into one patch]
Signed-off-by: Aman Sharma <amanharitsh123@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Karthikeyan Mitran <m.karthikeyan@mobiveil.co.in>
Cc: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Ryder Lee <ryder.lee@mediatek.com>
Cc: Marc Gonzalez <marc.w.gonzalez@free.fr>
When kdump is triggered, some PCI devices may have not been shut down
cleanly before the kdump kernel starts.
This causes the initial attempt to enter D0 state in the kdump kernel to
fail with invalid device state returned from Hyper-V host.
When this happens, explicitly call hv_pci_bus_exit() and retry to enter
the D0 state.
Link: https://lore.kernel.org/r/20200507050300.10974-1-weh@microsoft.com
Signed-off-by: Wei Hu <weh@microsoft.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
In some error cases in hv_pci_probe(), allocated resources are not freed.
Fix this by adding a field to keep track of the high water mark for slots
that have resources allocated to them. In case of an error, this high
water mark is used to know which slots have resources that must be released.
Since slots are numbered starting with zero, a value of -1 indicates no
slots have been allocated resources. There may be unused slots in the range
between slot 0 and the high water mark slot, but these slots are already
ignored by the existing code in the allocate and release loops with the call
to get_pcichild_wslot().
Link: https://lore.kernel.org/r/20200507050211.10923-1-weh@microsoft.com
Signed-off-by: Wei Hu <weh@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Some informal internal experiments has shown that the BrcmSTB ASPM L0s
savings may introduce an undesirable noise signal on some customers'
boards. In addition, L0s was found lacking in realized power savings,
especially relative to the L1 ASPM component. This is BrcmSTB's
experience and may not hold for others. At any rate, if the
'aspm-no-l0s' property is present L0s will be disabled.
Link: https://lore.kernel.org/r/20200507201544.43432-5-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
The outbound memory window registers were being referenced
with an incorrect stride offset. This probably wasn't noticed
previously as there was likely only one such window employed.
Link: https://lore.kernel.org/r/20200507201544.43432-3-james.quinlan@broadcom.com
Fixes: c045213703 ("PCI: brcmstb: Add Broadcom STB PCIe host controller driver")
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
clk_put() was being invoked on a clock obtained by
devm_clk_get_optional().
Link: https://lore.kernel.org/r/20200507201544.43432-2-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
While preparing the driver for upstream this detail was missed.
If not asserted during the initialization process, devices connected on
the bus will not be made aware of the internal reset happening. This,
potentially resulting in unexpected behavior.
Link: https://lore.kernel.org/r/20200507172020.18000-1-nsaenzjulienne@suse.de
Fixes: c045213703 ("PCI: brcmstb: Add Broadcom STB PCIe host controller driver")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
pci_epc_mem_init() internally used page size equal to *PAGE_SIZE* to
manage the address space so instead just pass the page size as a
argument to pci_epc_mem_init().
Also make pci_epc_mem_init() as a C function instead of a macro function
in preparation for adding support for pci-epc-mem core to handle multiple
windows.
Link: https://lore.kernel.org/r/1588854799-13710-5-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
The mask value was calculated incorrectly for PCIEPAMR register if the
size was less than 128 bytes. Fix this issue by adding a check on size.
Link: https://lore.kernel.org/r/1588854799-13710-4-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Move shareable code to common file pcie-rcar.c and the #defines to
pcie-rcar.h so that the common code can be reused with endpoint driver.
There are no functional changes with this patch for the host controller
driver.
Link: https://lore.kernel.org/r/1588854799-13710-3-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
This commit renames pcie-rcar.c to pcie-rcar-host.c in preparation for
adding support for endpoint mode. CONFIG_PCIE_RCAR is kept so that arm64
defconfig change can be a separate patch.
With this patch both config options PCIE_RCAR and PCIE_RCAR_HOST will be
available but PCIE_RCAR internally selects PCIE_RCAR_HOST so that bisect
builds wont be affected.
Link: https://lore.kernel.org/r/1588854799-13710-2-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Error code is stored in rp->reset_gpio and not in err variable.
Link: https://lore.kernel.org/r/20200414102512.27506-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Add suspend/resume support for rcar. The resume handler reprograms the
hardware based on the software state kept in specific device structures,
so there is no need to save registers on suspend.
Link: https://lore.kernel.org/r/20200314191232.3122290-1-marek.vasut@gmail.com
Link: https://lore.kernel.org/r/20200426123148.56051-1-marek.vasut@gmail.com
Signed-off-by: Kazufumi Ikeda <kaz-ikeda@xc.jp.nec.com>
Signed-off-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: linux-renesas-soc@vger.kernel.org
The outbound windows (PCIEPAUR(x), PCIEPALR(x)) describe a mapping between
a CPU address (which is determined by the window number 'x') and a
programmed PCI address - Thus allowing the controller to translate CPU
accesses into PCI accesses.
However the existing code incorrectly writes the CPU address - lets fix
this by writing the PCI address instead.
For memory transactions, existing DT users describe a 1:1 identity mapping
and thus this change should have no effect. However the same isn't true for
I/O.
Link: https://lore.kernel.org/r/20191004132941.6660-1-andrew.murray@arm.com
Fixes: c25da47788 ("PCI: rcar: Add Renesas R-Car PCIe driver")
Tested-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Most ECAM host drivers are just different pci_ecam_ops which can be DT
match table data. That's already the case in some cases, but let's
do that for all the ECAM drivers. Then we can use
of_device_get_match_data() in pci_host_common_probe() and eliminate the
probe wrapper functions and use pci_host_common_probe() directly for
probe.
Link: https://lore.kernel.org/r/20200409234923.21598-4-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Zhou Wang <wangzhou1@hisilicon.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <amurray@thegoodpenguin.co.uk>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Will Deacon <will@kernel.org>
Cc: Robert Richter <rrichter@marvell.com>
Cc: Marc Gonzalez <marc.w.gonzalez@free.fr>
Cc: Mans Rullgard <mans@mansr.com>
Cc: linux-pci@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
If we fails somewhere in 'v3_pci_probe()', we need to free 'host'.
Use the managed version of 'pci_alloc_host_bridge()' to do that easily.
The use of managed resources is already widely used in this driver.
Link: https://lore.kernel.org/r/20200418081637.1585-1-christophe.jaillet@wanadoo.fr
Fixes: 68a15eb7bd ("PCI: v3-semi: Add V3 Semiconductor PCI host driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Fix the following sparse warning:
drivers/pci/controller/dwc/pcie-hisi.c:365:21: warning:
symbol 'hisi_pcie_platform_ops' was not declared. Should it be static?
Link: https://lore.kernel.org/r/1587611883-26960-1-git-send-email-zou_wei@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
Commit 6f5e193bfb ("PCI: dwc: Fix dw_pcie_ep_raise_msix_irq() to get
correct MSI-X table address") overcomplicated the computation of the
msix_tbl address. Simplify it as it's simply the addr + offset. Provided
addr is (void *) already.
objdump -d shows no difference after this patch.
Link: https://lore.kernel.org/r/20200420065227.4920-1-jslaby@suse.cz
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Enable building host-generic and its host-common dependency as a
module.
Link: https://lore.kernel.org/r/20200409234923.21598-3-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Will Deacon <will@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <amurray@thegoodpenguin.co.uk>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Will Deacon <will@kernel.org>
Cc: linux-pci@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
struct pci_ecam_ops is typically DT match table data which is defined to
be const. It's also best practice for ops structs to be const. Ideally,
we'd make struct pci_ops const as well, but that becomes pretty
invasive, so for now we just cast it where needed.
Link: https://lore.kernel.org/r/20200409234923.21598-2-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <amurray@thegoodpenguin.co.uk>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Jonathan Chocron <jonnyc@amazon.com>
Cc: Zhou Wang <wangzhou1@hisilicon.com>
Cc: Robert Richter <rrichter@marvell.com>
Cc: Toan Le <toan@os.amperecomputing.com>
Cc: Marc Gonzalez <marc.w.gonzalez@free.fr>
Cc: Mans Rullgard <mans@mansr.com>
Cc: linux-acpi@vger.kernel.org
Drivers should not be selected by default because that bloats the kernel
for people who don't need them.
Remove the "default y" for CONFIG_PCI_KEYSTONE_HOST.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Drivers should not be selected by default because that bloats the kernel
for people who don't need them.
Enable CONFIG_PCI_DRA7XX_HOST by default only if SOC_DRA7XX.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: linux-omap@vger.kernel.org
The current implementation of hv_compose_msi_msg() is incompatible with
the new functionality that allows changing the vCPU a VMBus channel will
interrupt: if this function always calls hv_pci_onchannelcallback() in
the polling loop, the interrupt going to a different CPU could cause
hv_pci_onchannelcallback() to be running simultaneously in a tasklet,
which will break. The current code also has a problem in that it is not
synchronized with vmbus_reset_channel_cb(): hv_compose_msi_msg() could
be accessing the ring buffer via the call of hv_pci_onchannelcallback()
well after the time that vmbus_reset_channel_cb() has finished.
Fix these issues as follows. Disable the channel tasklet before
entering the polling loop in hv_compose_msi_msg() and re-enable it when
done. This will prevent hv_pci_onchannelcallback() from running in a
tasklet on a different CPU. Moreover, poll by always calling
hv_pci_onchannelcallback(), but check the channel callback function for
NULL and invoke the callback within a sched_lock critical section. This
will prevent hv_compose_msi_msg() from accessing the ring buffer after
vmbus_reset_channel_cb() has acquired the sched_lock spinlock.
Suggested-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <amurray@thegoodpenguin.co.uk>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: <linux-pci@vger.kernel.org>
Link: https://lore.kernel.org/r/20200406001514.19876-8-parri.andrea@gmail.com
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Wei Liu <wei.liu@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQJIBAABCgAyFiEEgMe7l+5h9hnxdsnuWYigwDrT+vwFAl6GTQMUHGJoZWxnYWFz
QGdvb2dsZS5jb20ACgkQWYigwDrT+vy3PhAAmqpYBRobOsG8QbmKDjoJEFtkqdvD
z6+4zf/R+hF11RyXjMDwihIe8d+tkQ4eAaYu6Oh5PrTyanz0G0PgeCrivZeytULk
thqQIWzDQMVA5vN/2/Vy8s5s+3HzP8z/MZOFScJ7+xA1MndXptPRTNmFUbjx+GAv
x8/pTp0u9AF6m7itX65DxXvwkzjWamt+Ar4Yx2IcuKAU/M5RtfuZO3PpDnqn7/wk
JFlkRoYeFB6qNnnkPdeyPHl9dALhuhzgdTyklQEnKVW3nf3xThYDhcEwdh6kBQgl
0dH8lL5LXy7PKGN8RES4wB0Vqndw/HlsCF5O4wkkfItbnbJxGJtS139e5973m0ud
sgWvF4yJAT2jCKhIeNz34sePQJMyWALhv0XzZCsJ0YeGHsrV1jrHELkwUT1+eIsT
3UV0iZ6aL06zQJDyKUbbIcQzEQ/wwBC+x9VgsyL54K1quCQZ1N1Nl/dvrb4cRG9m
m9EhJK/brDf4c0uFlOmMTSxV1t5J+z6ZSQnh1ShD/o5yBsxqN6q5brDT6LEs+jbM
LsIkA18jJOd4OyiDs98YiFKvIfFQbQ0LEBQpJwhF0snvfBFMMbUYN/T/NYneWON/
F0TpkFoP7PXDuq55iNaLdnObfzrpC9kdzUyWvePUvjxIl55bkf+/qtUny+H48t4L
dNggvW052d7BHes=
=deWu
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Revert sysfs "rescan" renames that broke apps (Kelsey Skunberg)
- Add more 32 GT/s link speed decoding and improve the implementation
(Yicong Yang)
Resource management:
- Add support for sizing programmable host bridge apertures and fix a
related alpha Nautilus regression (Ivan Kokshaysky)
Interrupts:
- Add boot interrupt quirk mechanism for Xeon chipsets and document
boot interrupts (Sean V Kelley)
PCIe native device hotplug:
- When possible, disable in-band presence detect and use PDS
(Alexandru Gagniuc)
- Add DMI table for devices that don't use in-band presence detection
but don't advertise that correctly (Stuart Hayes)
- Fix hang when powering slots up/down via sysfs (Lukas Wunner)
- Fix an MSI interrupt race (Stuart Hayes)
Virtualization:
- Add ACS quirks for Zhaoxin devices (Raymond Pang)
Error handling:
- Add Error Disconnect Recover (EDR) support so firmware can report
devices disconnected via DPC and we can try to recover (Kuppuswamy
Sathyanarayanan)
Peer-to-peer DMA:
- Add Intel Sky Lake-E Root Ports B, C, D to the whitelist (Andrew
Maier)
ASPM:
- Reduce severity of common clock config message (Chris Packham)
- Clear the correct bits when enabling L1 substates, so we don't go
to the wrong state (Yicong Yang)
Endpoint framework:
- Replace EPF linkup ops with notifier call chain and improve locking
(Kishon Vijay Abraham I)
- Fix concurrent memory allocation in OB address region (Kishon Vijay
Abraham I)
- Move PF function number assignment to EPC core to support multiple
function creation methods (Kishon Vijay Abraham I)
- Fix issue with clearing configfs "start" entry (Kunihiko Hayashi)
- Fix issue with endpoint MSI-X ignoring BAR Indicator and Table
Offset (Kishon Vijay Abraham I)
- Add support for testing DMA transfers (Kishon Vijay Abraham I)
- Add support for testing > 10 endpoint devices (Kishon Vijay Abraham I)
- Add support for tests to clear IRQ (Kishon Vijay Abraham I)
- Add common DT schema for endpoint controllers (Kishon Vijay Abraham I)
Amlogic Meson PCIe controller driver:
- Add DT bindings for AXG PCIe PHY, shared MIPI/PCIe analog PHY (Remi
Pommarel)
- Add Amlogic AXG PCIe PHY, AXG MIPI/PCIe analog PHY drivers (Remi
Pommarel)
Cadence PCIe controller driver:
- Add Root Complex/Endpoint DT schema for Cadence PCIe (Kishon Vijay
Abraham I)
Intel VMD host bridge driver:
- Add two VMD Device IDs that require bus restriction mode (Sushma
Kalakota)
Mobiveil PCIe controller driver:
- Refactor and modularize mobiveil driver (Hou Zhiqiang)
- Add support for Mobiveil GPEX Gen4 host (Hou Zhiqiang)
Microsoft Hyper-V host bridge driver:
- Add support for Hyper-V PCI protocol version 1.3 and
PCI_BUS_RELATIONS2 (Long Li)
- Refactor to prepare for virtual PCI on non-x86 architectures (Boqun
Feng)
- Fix memory leak in hv_pci_probe()'s error path (Dexuan Cui)
NVIDIA Tegra PCIe controller driver:
- Use pci_parse_request_of_pci_ranges() (Rob Herring)
- Add support for endpoint mode and related DT updates (Vidya Sagar)
- Reduce -EPROBE_DEFER error message log level (Thierry Reding)
Qualcomm PCIe controller driver:
- Restrict class fixup to specific Qualcomm devices (Bjorn Andersson)
Synopsys DesignWare PCIe controller driver:
- Refactor core initialization code for endpoint mode (Vidya Sagar)
- Fix endpoint MSI-X to use correct table address (Kishon Vijay
Abraham I)
TI DRA7xx PCIe controller driver:
- Fix MSI IRQ handling (Vignesh Raghavendra)
TI Keystone PCIe controller driver:
- Allow AM654 endpoint to raise MSI-X interrupt (Kishon Vijay Abraham I)
Miscellaneous:
- Quirk ASMedia XHCI USB to avoid "PME# from D0" defect (Kai-Heng
Feng)
- Use ioremap(), not phys_to_virt(), for platform ROM to fix video
ROM mapping with CONFIG_HIGHMEM (Mikel Rychliski)"
* tag 'pci-v5.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (96 commits)
misc: pci_endpoint_test: remove duplicate macro PCI_ENDPOINT_TEST_STATUS
PCI: tegra: Print -EPROBE_DEFER error message at debug level
misc: pci_endpoint_test: Use full pci-endpoint-test name in request_irq()
misc: pci_endpoint_test: Fix to support > 10 pci-endpoint-test devices
tools: PCI: Add 'e' to clear IRQ
misc: pci_endpoint_test: Add ioctl to clear IRQ
misc: pci_endpoint_test: Avoid using module parameter to determine irqtype
PCI: keystone: Allow AM654 PCIe Endpoint to raise MSI-X interrupt
PCI: dwc: Fix dw_pcie_ep_raise_msix_irq() to get correct MSI-X table address
PCI: endpoint: Fix ->set_msix() to take BIR and offset as arguments
misc: pci_endpoint_test: Add support to get DMA option from userspace
tools: PCI: Add 'd' command line option to support DMA
misc: pci_endpoint_test: Use streaming DMA APIs for buffer allocation
PCI: endpoint: functions/pci-epf-test: Print throughput information
PCI: endpoint: functions/pci-epf-test: Add DMA support to transfer data
PCI: pciehp: Fix MSI interrupt race
PCI: pciehp: Fix indefinite wait on sysfs requests
PCI: endpoint: Fix clearing start entry in configfs
PCI: tegra: Add support for PCIe endpoint mode in Tegra194
PCI: sysfs: Revert "rescan" file renames
...
- Apply Qualcomm class fixup only to PCIe host bridges, not to all
PCI_VENDOR_ID_QCOM devices (Bjorn Andersson)
* remotes/lorenzo/pci/qcom:
PCI: qcom: Fix the fixup of PCI_VENDOR_ID_QCOM
- Restructure mobiveil driver to support either Root Complex mode or
Endpoint mode (Hou Zhiqiang)
- Collect host initialization into one place (Hou Zhiqiang)
- Collect interrupt-related code into one place (Hou Zhiqiang)
- Split mobiveil into separate files under
drivers/pci/controller/mobiveil for easier reuse (Hou Zhiqiang)
- Add callbacks for interrupt initialization and linkup checking (Hou
Zhiqiang)
- Add 8- and 16-bit CSR accessors (Hou Zhiqiang)
- Initialize host driver only if Header Type is "bridge" (Hou Zhiqiang)
- Add DT bindings for NXP Layerscape SoCs PCIe Gen4 controller (Hou
Zhiqiang)
- Add PCIe Gen4 RC driver for Layerscape SoCs (Hou Zhiqiang)
- Add pcie-mobiveil __iomem annotations (Hou Zhiqiang)
- Add PCI_MSI_IRQ_DOMAIN Kconfig dependency (Hou Zhiqiang)
* remotes/lorenzo/pci/mobiveil:
PCI: mobiveil: Fix unmet dependency warning for PCIE_MOBIVEIL_PLAT
PCI: mobiveil: Fix sparse different address space warnings
PCI: mobiveil: Add PCIe Gen4 RC driver for Layerscape SoCs
dt-bindings: PCI: Add NXP Layerscape SoCs PCIe Gen4 controller
PCI: mobiveil: Add Header Type field check
PCI: mobiveil: Add 8-bit and 16-bit CSR register accessors
PCI: mobiveil: Allow mobiveil_host_init() to be used to re-init host
PCI: mobiveil: Add callback function for link up check
PCI: mobiveil: Add callback function for interrupt initialization
PCI: mobiveil: Modularize the Mobiveil PCIe Host Bridge IP driver
PCI: mobiveil: Collect the interrupt related operations into a function
PCI: mobiveil: Move the host initialization into a function
PCI: mobiveil: Introduce a new structure mobiveil_root_port
- Fix memory leak in hv probe path (Dexuan Cui)
- Add support for Hyper-V protocol 1.3 (Long Li)
- Replace zero-length array with flexible-array member (Gustavo A. R.
Silva)
- Move hypercall definitions to <asm/hyperv-tlfs.h> (Boqun Feng)
- Move retarget definitions to <asm/hyperv-tlfs.h> and make them packed
(Boqun Feng)
- Add struct hv_msi_entry and hv_set_msi_entry_from_desc() to prepare for
future virtual PCI on non-x86 (Boqun Feng)
* remotes/lorenzo/pci/hv:
PCI: hv: Introduce hv_msi_entry
PCI: hv: Move retarget related structures into tlfs header
PCI: hv: Move hypercall related definitions into tlfs header
PCI: hv: Replace zero-length array with flexible-array member
PCI: hv: Add support for protocol 1.3 and support PCI_BUS_RELATIONS2
PCI: hv: Decouple the func definition in hv_dr_state from VSP message
PCI: hv: Add missing kfree(hbus) in hv_pci_probe()'s error handling path
PCI: hv: Remove unnecessary type casting from kzalloc
- Use notification chain instead of EPF linkup ops for EPC events (Kishon
Vijay Abraham I)
- Protect concurrent allocation in endpoint outbound address region
(Kishon Vijay Abraham I)
- Protect concurrent access to pci_epf_ops (Kishon Vijay Abraham I)
- Assign function number for each PF in endpoint core (Kishon Vijay
Abraham I)
- Refactor endpoint mode core initialization (Vidya Sagar)
- Add API to notify when core initialization completes (Vidya Sagar)
- Add test framework support to defer core initialization (Vidya Sagar)
- Update Tegra SoC ABI header to support uninitialization of UPHY PLL
when in endpoint mode without reference clock (Vidya Sagar)
- Add DT and driver support for Tegra194 PCIe endpoint nodes (Vidya
Sagar)
- Add endpoint test support for DMA data transfer (Kishon Vijay
Abraham I)
- Print throughput information in endpoint test (Kishon Vijay Abraham I)
- Use streaming DMA APIs for endpoint test buffer allocation (Kishon
Vijay Abraham I)
- Add endpoint test command line option for DMA (Kishon Vijay Abraham I)
- When stopping a controller via configfs, clear endpoint "start" entry
to prevent WARN_ON (Kunihiko Hayashi)
- Update endpoint ->set_msix() to pay attention to MSI-X BAR Indicator
and offset when finding MSI-X tables (Kishon Vijay Abraham I)
- MSI-X tables are in local memory, not in the PCI address space. Update
pcie-designware-ep to account for this (Kishon Vijay Abraham I)
- Allow AM654 PCIe Endpoint to raise MSI-X interrupts (Kishon Vijay
Abraham I)
- Avoid using module parameter to determine irqtype for endpoint test
(Kishon Vijay Abraham I)
- Add ioctl to clear IRQ for endpoint test (Kishon Vijay Abraham I)
- Add endpoint test 'e' option to clear IRQ (Kishon Vijay Abraham I)
- Bump limit on number of endpoint test devices from 10 to 10,000 (Kishon
Vijay Abraham I)
- Use full pci-endpoint-test name in request_irq() for easier profiling
(Kishon Vijay Abraham I)
- Reduce log level of -EPROBE_DEFER error messages to debug (Thierry
Reding)
* remotes/lorenzo/pci/endpoint:
misc: pci_endpoint_test: remove duplicate macro PCI_ENDPOINT_TEST_STATUS
PCI: tegra: Print -EPROBE_DEFER error message at debug level
misc: pci_endpoint_test: Use full pci-endpoint-test name in request_irq()
misc: pci_endpoint_test: Fix to support > 10 pci-endpoint-test devices
tools: PCI: Add 'e' to clear IRQ
misc: pci_endpoint_test: Add ioctl to clear IRQ
misc: pci_endpoint_test: Avoid using module parameter to determine irqtype
PCI: keystone: Allow AM654 PCIe Endpoint to raise MSI-X interrupt
PCI: dwc: Fix dw_pcie_ep_raise_msix_irq() to get correct MSI-X table address
PCI: endpoint: Fix ->set_msix() to take BIR and offset as arguments
misc: pci_endpoint_test: Add support to get DMA option from userspace
tools: PCI: Add 'd' command line option to support DMA
misc: pci_endpoint_test: Use streaming DMA APIs for buffer allocation
PCI: endpoint: functions/pci-epf-test: Print throughput information
PCI: endpoint: functions/pci-epf-test: Add DMA support to transfer data
PCI: endpoint: Fix clearing start entry in configfs
PCI: tegra: Add support for PCIe endpoint mode in Tegra194
dt-bindings: PCI: tegra: Add DT support for PCIe EP nodes in Tegra194
soc/tegra: bpmp: Update ABI header
PCI: pci-epf-test: Add support to defer core initialization
PCI: dwc: Add API to notify core initialization completion
PCI: endpoint: Add notification for core init completion
PCI: dwc: Refactor core initialization code for EP mode
PCI: endpoint: Add core init notifying feature
PCI: endpoint: Assign function number for each PF in EPC core
PCI: endpoint: Protect concurrent access to pci_epf_ops with mutex
PCI: endpoint: Fix for concurrent memory allocation in OB address region
PCI: endpoint: Replace spinlock with mutex
PCI: endpoint: Use notification chain mechanism to notify EPC events to EPF
Probe deferral is an expected error condition that will usually be
recovered from. Print such error messages at debug level to make them
available for diagnostic purposes when building with debugging enabled
and hide them otherwise to not spam the kernel log with them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Tested-by: Vidya Sagar <vidyas@nvidia.com>
AM654 PCIe EP controller has MSI-X capability register and has the
ability to raise MSI-X interrupt. Add support in pci-keystone.c
for PCIe endpoint controller in AM654 to raise MSI-X interrupts.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
commit beb4641a78 ("PCI: dwc: Add MSI-X callbacks handler"),
in order to raise MSI-X interrupt, obtained MSIX table address from
Base Address Register (BAR). However BAR only holds PCI address
programmed by the host whereas the MSI-X table should be in the local
memory.
Store the MSI-X table address (virtual address) as part of ->set_bar()
callback and use that to get the message address and message data
here.
Fixes: beb4641a78 ("PCI: dwc: Add MSI-X callbacks handler")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
commit 8963106eab ("PCI: endpoint: Add MSI-X interfaces") while
adding support to raise MSI-X interrupts from endpoint didn't include
BAR Indicator register (BIR) configuration and MSI-X table offset as
arguments in pci_epc_set_msix(). This would result in endpoint
controller register using random BAR indicator register, the memory
for which might not be allocated by the endpoint function driver.
Add BAR indicator register and MSI-X table offset as arguments in
pci_epc_set_msix() and allocate space for MSI-X table and pending
bit array (PBA) in pci-epf-test endpoint function driver.
Fixes: 8963106eab ("PCI: endpoint: Add MSI-X interfaces")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add support for the endpoint mode of Synopsys DesignWare core based
dual mode PCIe controllers present in Tegra194 SoC.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Due to an issue with PCIe wrapper logic built for the DWC PCIe IP on
dra7xx, the driver needs to ensure that there are no pending MSI IRQ
vector set (i.e PCIE_MSI_INTR0_STATUS reads 0 at least once) before
exiting IRQ handler otherwise the dra7xx PCIe wrapper will not register
new MSI IRQs even though PCIE_MSI_INTR0_STATUS reports IRQs are pending.
Therefore it's no longer possible to use default IRQ handler provided by
DWC library.
Add an irqchip implementation inside pci-dra7xx.c and install new MSI
IRQ handler to handle the above errata.
This fixes a bug, where PCIe wifi cards with 4 DMA queues like Intel
8260 used to throw following error and stall during ping/iperf3 tests.
[ 97.776310] iwlwifi 0000:01:00.0: Queue 9 stuck for 2500 ms.
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Fix the following warning by adding the dependency PCI_MSI_IRQ_DOMAIN
to PCIE_MOBIVEIL_PLAT.
WARNING: unmet direct dependencies detected for PCIE_MOBIVEIL_HOST
Depends on [n]: PCI [=y] && PCI_MSI_IRQ_DOMAIN [=n]
Selected by [y]:
- PCIE_MOBIVEIL_PLAT [=y] && PCI [=y] && (ARCH_ZYNQMP || COMPILE_TEST [=y]) && OF [=y]
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Previously some PCI speed strings came from pci_speed_string(), some came
from the PCIe-specific PCIE_SPEED2STR(), and some came from a PCIe-specific
switch statement. These methods were inconsistent:
pci_speed_string() PCIE_SPEED2STR() switch
------------------ ---------------- ------
33 MHz PCI
...
2.5 GT/s PCIe 2.5 GT/s 2.5 GT/s
5.0 GT/s PCIe 5 GT/s 5 GT/s
8.0 GT/s PCIe 8 GT/s 8 GT/s
16.0 GT/s PCIe 16 GT/s 16 GT/s
32.0 GT/s PCIe 32 GT/s 32 GT/s
Standardize on pci_speed_string() as the single source of these strings.
Note that this adds ".0" and "PCIe" to some messages, including sysfs
"max_link_speed" files, a brcmstb "link up" message, and the link status
dmesg logging, e.g.,
nvme 0000:01:00.0: 16.000 Gb/s available PCIe bandwidth, limited by 5.0 GT/s PCIe x4 link at 0000:00:01.1 (capable of 31.504 Gb/s with 8.0 GT/s PCIe x4 link)
I think it's better to standardize on a single version of the speed text.
Previously we had strings like this:
/sys/bus/pci/slots/0/cur_bus_speed: 8.0 GT/s PCIe
/sys/bus/pci/slots/0/max_bus_speed: 8.0 GT/s PCIe
/sys/devices/pci0000:00/0000:00:1c.0/current_link_speed: 8 GT/s
/sys/devices/pci0000:00/0000:00:1c.0/max_link_speed: 8 GT/s
This changes the latter two to match the slots files:
/sys/devices/pci0000:00/0000:00:1c.0/current_link_speed: 8.0 GT/s PCIe
/sys/devices/pci0000:00/0000:00:1c.0/max_link_speed: 8.0 GT/s PCIe
Based-on-patch by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a new structure (hv_msi_entry), which is also defined in the TLFS,
to describe the msi entry for HVCALL_RETARGET_INTERRUPT. The structure
is needed because its layout may be different from architecture to
architecture.
Also add a new generic interface hv_set_msi_entry_from_desc() to allow
different archs to set the msi entry from msi_desc.
No functional change, only preparation for the future support of virtual
PCI on non-x86 architectures.
Signed-off-by: Boqun Feng (Microsoft) <boqun.feng@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Currently, retarget_msi_interrupt and other structures it relys on are
defined in pci-hyperv.c. However, those structures are actually defined
in Hypervisor Top-Level Functional Specification [1] and may be
different in sizes of fields or layout from architecture to
architecture. Let's move those definitions into x86's tlfs header file
to support virtual PCI on non-x86 architectures in the future. Note that
"__packed" attribute is added to these structures during the movement
for the same reason as we use the attribute for other TLFS structures in
the header file: make sure the structures meet the specification and
avoid anything unexpected from the compilers.
Additionally, rename struct retarget_msi_interrupt to
hv_retarget_msi_interrupt for the consistent naming convention, also
mirroring the name in TLFS.
[1]: https://docs.microsoft.com/en-us/virtualization/hyper-v-on-windows/reference/tlfs
Signed-off-by: Boqun Feng (Microsoft) <boqun.feng@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Currently HVCALL_RETARGET_INTERRUPT and HV_PARTITION_ID_SELF are defined
in pci-hyperv.c. However, similar to other hypercall related
definitions, it makes more sense to put them in the tlfs header file.
Besides, these definitions are arch-dependent, so for the support of
virtual PCI on non-x86 archs in the future, move them into arch-specific
tlfs header file.
Signed-off-by: Boqun Feng (Microsoft) <boqun.feng@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <amurray@thegoodpenguin.co.uk>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Starting with Hyper-V PCI protocol version 1.3, the host VSP can send
PCI_BUS_RELATIONS2 and pass the vNUMA node information for devices on the
bus. The vNUMA node tells which guest NUMA node this device is on based
on guest VM configuration topology and physical device information.
Add code to negotiate v1.3 and process PCI_BUS_RELATIONS2.
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
hv_dr_state is used to find present PCI devices on the bus. The structure
reuses struct pci_function_description from VSP message to describe a
device.
To prepare support for pci_function_description v2, decouple this
dependence in hv_dr_state so it can work with both v1 and v2 VSP messages.
There is no functionality change.
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Now that PCIE PHY has been introduced for AXG, the whole has_shared_phy
logic can be mutualized between AXG and G12A platforms.
This new PHY makes use of the shared MIPI/PCIE analog PHY found on AXG
platforms, which need to be used in order to have reliable PCIE
communications.
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Some older compilers have no implementation for the helper for 64-bit
unsigned division/modulo, so linking pcie-brcmstb driver causes the
"undefined reference to `__aeabi_uldivmod'" error.
*rc_bar2_size is always a power of two, because it is calculated as:
"1ULL << fls64(entry->res->end - entry->res->start)", so the modulo
operation in the subsequent check can be replaced by a simple logical
AND with a proper mask.
Link: https://lore.kernel.org/r/20200227115146.24515-1-m.szyprowski@samsung.com
Fixes: c045213703 ("PCI: brcmstb: Add Broadcom STB PCIe host controller driver")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
There exists non-bridge PCIe devices with PCI_VENDOR_ID_QCOM, so limit
the fixup to only affect the relevant PCIe bridges.
Fixes: 322f034366 ("PCI: qcom: Use default config space read function")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: stable@vger.kernel.org # v5.2+
Add a new API dw_pcie_ep_init_notify() to let platform drivers
call it when the core is available for initialization.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Split core initialization code for EP mode into two, one that doesn't
touch core registers and the other that touches core registers. The latter
would be called/skipped based on the EPC feature 'core_init_notifier'.
In platforms where this is skipped, it would be called indirectly
through hooks from the endpoint function driver.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Convert Tegra PCI host driver to use the common
pci_parse_request_of_pci_ranges().
This allows removing the DT ranges parsing, PCI resource handling, and
private storage of resources from the driver.
Tested-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <andrew.murray@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Now that we use kzalloc() to allocate the hbus buffer, we must call
kfree() in the error path as well to prevent memory leakage.
Fixes: 877b911a5b ("PCI: hv: Avoid a kmemleak false positive caused by the hbus buffer")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
In C, there is no need to cast a void * to any other pointer type,
remove an unnecessary cast.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Check the Header Type and exit from the host driver initialization if
it is not in host mode.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <amurray@thegoodpenguin.co.uk>
There are some 8-bit and 16-bit registers in PCIe configuration
space, so add these accessors accordingly.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
Reviewed-by: Andrew Murray <amurray@thegoodpenguin.co.uk>
Allow the mobiveil_host_init() function to be used to re-init
host controller's PAB and GPEX CSR register block, since the NXP
integrated Mobiveil IP has to reset and then re-init the PAB
and GPEX CSR registers upon hot-reset.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
Reviewed-by: Andrew Murray <amurray@thegoodpenguin.co.uk>
Platforms integrating the Mobiveil GPEX can implement a specific
mechanism to check the link status.
Add a callback to enable platform specific link status functions.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[lorenzo.pieralisi@arm.com: updated log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
The Mobiveil GPEX internal MSI/INTx controller is not implemented
in all platforms in which the Mobiveil GPEX is integrated.
Allow platforms to implement their specific interrupt initialization.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <amurray@thegoodpenguin.co.uk>
Modularize the Mobiveil PCIe host driver according to the abstraction of
Root Complex and Endpoint and move it into a new directory in order to
make it easier to reuse the driver functions to add new host drivers for
systems integrating the Mobiveil PCIe GPEX IP.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Collect the interrupt initialization related operations into
a new function to make code more readable.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <amurray@thegoodpenguin.co.uk>
Move the host initialization related operations into a new
function so that it can be reused by other platform
PCIe host drivers integrating the Mobiveil GPEX.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <amurray@thegoodpenguin.co.uk>
The Mobiveil PCIe controller can work in either Root Complex
mode or Endpoint mode.
Introduce a new structure mobiveil_root_port and abstract the
RC related members into it so that the code can be used by both
modes.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <amurray@thegoodpenguin.co.uk>
- Remove unused modular code from uniphier, which cannot be built as a
module (Masahiro Yamada)
* remotes/lorenzo/pci/uniphier:
PCI: uniphier: remove module code from built-in driver
- Add DT clock/reset info for SDM845 PCIe controller (Bjorn Andersson)
- Add support for SDM845 PCIe controller to the qcom driver (Bjorn
Andersson)
* remotes/lorenzo/pci/qcom:
PCI: qcom: Add support for SDM845 PCIe controller
dt-bindings: PCI: qcom: Add support for SDM845 PCIe
- Fix link training so we can do it more than once (Yurii Monakov)
- Fix keystone outbound window mapping (Yurii Monakov)
- Fix error handling when DT lacks "num-viewport" (Kishon Vijay Abraham I)
* remotes/lorenzo/pci/keystone:
PCI: keystone: Fix error handling when "num-viewport" DT property is not populated
PCI: keystone: Fix outbound region mapping
PCI: keystone: Fix link training retries initiation
Add new VMD device IDs that require the bus restriction mode.
Signed-off-by: Sushma Kalakota <sushmax.kalakota@intel.com>
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This adds MSI support to the Broadcom STB PCIe host controller. The MSI
controller is physically located within the PCIe block, however, there
is no reason why the MSI controller could not be moved elsewhere in the
future. MSIX is not supported by the HW.
Since the internal Brcmstb MSI controller is intertwined with the PCIe
controller, it is not its own platform device but rather part of the
PCIe platform device.
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Co-developed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
This adds a basic driver for Broadcom's STB PCIe controller, for now
aimed at Raspberry Pi 4's SoC, bcm2711.
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Co-developed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
[lorenzo.pieralisi@arm.com: updated brcm_pcie_get_rc_bar2_size_and_offset()according to https://lore.kernel.org/linux-pci/be8ddb33a7360af1815cf686f77f3f0913d02be3.camel@suse.de]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Reviewed-by: Jeremy Linton <jeremy.linton@arm.com>
Devices on the VMD domain use the VMD endpoint's requester ID and have been
relying on the VMD endpoint's DMA operations. The problem with this was
that VMD domain devices would use the VMD endpoint's attributes when doing
DMA and IOMMU mapping. We can be smarter about this by only using the VMD
endpoint when mapping and providing the correct child device's attributes
during DMA operations.
Remove the dma_map_ops redirect.
Link: https://lore.kernel.org/r/1579613871-301529-7-git-send-email-jonathan.derrick@intel.com
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Expose VMD's pci_dev pointer in struct pci_sysdata. This will be used
indirectly by intel-iommu.c to find the correct domain.
Link: https://lore.kernel.org/r/1579613871-301529-3-git-send-email-jonathan.derrick@intel.com
[bhelgaas: commit log]
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Christoph Hellwig <hch@lst.de>
Fix error handling when "num-viewport" DT property is not populated.
Fixes: 23284ad677 ("PCI: keystone: Add support for PCIe EP in AM654x Platforms")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org # v5.2+
builtin_platform_driver() and MODULE_* are always odd combination.
This file is not compiled as a module by anyone because
CONFIG_PCIE_UNIPHIER is a bool option.
Let's remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove" code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Fix up inconsistent usage of upper and lowercase letters in "Exynos"
name.
"EXYNOS" is not an abbreviation but a regular trademarked name.
Therefore it should be written with lowercase letters starting with
capital letter.
The lowercase "Exynos" name is promoted by its manufacturer Samsung
Electronics Co., Ltd., in advertisement materials and on website.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Fix AFI_PEX2_CTRL reg offset for Tegra30 by moving it from the Tegra20
SoC struct where it erroneously got added. This fixes the AFI_PEX2_CTRL
reg offset being uninitialised subsequently failing to bring up the
third PCIe port.
Fixes: adb2653b3d ("PCI: tegra: Add AFI_PEX2_CTRL reg offset as part of SoC struct")
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
pm_runtime_get_sync() returns the device's usage counter. This might
be >0 if the device is already powered up or CONFIG_PM is disabled.
Abort probe function on real error only.
Fixes: da76ba5096 ("PCI: tegra: Add power management support")
Link: https://lore.kernel.org/r/20191216111825.28136-1-david.engraf@sysgo.com
Signed-off-by: David Engraf <david.engraf@sysgo.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Andrew Murray <andrew.murray@arm.com>
Cc: stable@vger.kernel.org # v4.17+
The Keystone outbound Address Translation Unit (ATU) maps PCI MMIO space in
8 MB windows. When programming the ATU windows, we previously incremented
the starting address by 8, not 8 MB, so all the windows were mapped to the
first 8 MB. Therefore, only 8 MB of MMIO space was accessible.
Update the loop so it increments the starting address by 8 MB, not 8, so
more MMIO space is accessible.
Fixes: e75043ad97 ("PCI: keystone: Cleanup outbound window configuration")
Link: https://lore.kernel.org/r/20191004154811.GA31397@monakov-y.office.kontur-niirs.ru
Signed-off-by: Yurii Monakov <monakov.y@gmail.com>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Cc: stable@vger.kernel.org # v4.20+
ks_pcie_stop_link() function does not clear LTSSM_EN_VAL bit so
link training was not triggered more than once after startup.
In configurations where link can be unstable during early boot,
for example, under low temperature, it will never be established.
Fixes: 0c4ffcfe1f ("PCI: keystone: Add TI Keystone PCIe driver")
Signed-off-by: Yurii Monakov <monakov.y@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Andrew Murray <andrew.murray@arm.com>
Cc: stable@vger.kernel.org
The SDM845 has one Gen2 and one Gen3 controller, add support for these.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Use DesignWare helper functions to configure Fast Training
Sequence. Drop the respective code in the driver.
Signed-off-by: Dilip Kota <eswara.kota@linux.intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Add support to PCIe RC controller on Intel Gateway SoCs.
PCIe controller is based of Synopsys DesignWare PCIe core.
Intel PCIe driver requires Upconfigure support, Fast Training
Sequence and link speed configurations. So adding the respective
helper functions in the PCIe DesignWare framework.
It also programs hardware autonomous speed during speed
configuration so defining it in pci_regs.h.
Also, mark Intel PCIe driver depends on MSI IRQ Domain
as Synopsys DesignWare framework depends on the
PCI_MSI_IRQ_DOMAIN.
Signed-off-by: Dilip Kota <eswara.kota@linux.intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Previously quirk_paxc_bridge() was applied when the iproc driver was
built-in, but not when it was compiled as a module.
This happened because it was under #ifdef CONFIG_PCIE_IPROC_PLATFORM:
PCIE_IPROC_PLATFORM=y causes CONFIG_PCIE_IPROC_PLATFORM to be defined, but
PCIE_IPROC_PLATFORM=m causes CONFIG_PCIE_IPROC_PLATFORM_MODULE to be
defined.
Move quirk_paxc_bridge() to pcie-iproc.c and drop the #ifdef so the quirk
is always applied, whether iproc is built-in or a module.
[bhelgaas: commit log, move to pcie-iproc.c, not pcie-iproc-platform.c]
Link: https://lore.kernel.org/r/20191211174511.89713-1-wei.liu@kernel.org
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- Consolidate DT "dma-ranges" parsing and convert all host drivers to use
shared parsing (Rob Herring)
* remotes/lorenzo/pci/mmio-dma-ranges:
PCI: Make devm_of_pci_get_host_bridge_resources() static
PCI: rcar: Use inbound resources for setup
PCI: iproc: Use inbound resources for setup
PCI: xgene: Use inbound resources for setup
PCI: v3-semi: Use inbound resources for setup
PCI: ftpci100: Use inbound resources for setup
PCI: of: Add inbound resource parsing to helpers
PCI: versatile: Enable COMPILE_TEST
PCI: versatile: Remove usage of PHYS_OFFSET
PCI: versatile: Use pci_parse_request_of_pci_ranges()
PCI: xilinx-nwl: Use pci_parse_request_of_pci_ranges()
PCI: xilinx: Use pci_parse_request_of_pci_ranges()
PCI: xgene: Use pci_parse_request_of_pci_ranges()
PCI: v3-semi: Use pci_parse_request_of_pci_ranges()
PCI: rockchip: Drop storing driver private outbound resource data
PCI: rockchip: Use pci_parse_request_of_pci_ranges()
PCI: mobiveil: Use pci_parse_request_of_pci_ranges()
PCI: mediatek: Use pci_parse_request_of_pci_ranges()
PCI: iproc: Use pci_parse_request_of_pci_ranges()
PCI: faraday: Use pci_parse_request_of_pci_ranges()
PCI: dwc: Use pci_parse_request_of_pci_ranges()
PCI: altera: Use pci_parse_request_of_pci_ranges()
PCI: aardvark: Use pci_parse_request_of_pci_ranges()
PCI: Export pci_parse_request_of_pci_ranges()
resource: Add a resource_list_first_type helper
# Conflicts:
# drivers/pci/controller/pcie-rcar.c
- Add VMD bus 224-255 restriction decode (Jon Derrick)
- Add VMD 8086:9A0B device ID (Jon Derrick)
- Remove Keith from VMD maintainer list (Keith Busch)
* remotes/lorenzo/pci/vmd:
MAINTAINERS: Remove Keith from VMD maintainer
PCI: vmd: Add device id for VMD device 8086:9A0B
PCI: vmd: Add bus 224-255 restriction decode
- Make rockchip 0V9 and 1V8 power regulators non-optional (Robin Murphy)
* remotes/lorenzo/pci/rockchip:
PCI: rockchip: Make some regulators non-optional
- Clear bit 0 of MACCTLR before PCIETCTLR.CFINIT per manual (Yoshihiro
Shimoda)
- Remove unnecessary header include from rcar (Andrew Murray)
- Tighten register index checking for rcar inbound range programming
(Marek Vasut)
- Fix rcar inbound range alignment calculation to improve packing of
multiple entries (Marek Vasut)
- Update rcar MACCTLR setting to match documentation (Yoshihiro Shimoda)
* remotes/lorenzo/pci/rcar:
PCI: rcar: Fix missing MACCTLR register setting in initialization sequence
PCI: rcar: Recalculate inbound range alignment for each controller entry
PCI: rcar: Move the inbound index check
PCI: rcar: Remove unnecessary header include (../pci.h)
- Refactor Cadence PCIe host controller to use as a library for both host
and endpoint (Tom Joseph)
* remotes/lorenzo/pci/cadence:
PCI: cadence: Move all files to per-device cadence directory
PCI: cadence: Refactor driver to use as a core library
- Use LTSSM state to build link training flag since Aardvark doesn't
implement the Link Training bit (Remi Pommarel)
- Delay before training Aardvark link in case PERST# was asserted before
the driver probe (Remi Pommarel)
- Fix Aardvark issues with Root Control reads and writes (Remi Pommarel)
- Don't rely on jiffies in Aardvark config access path since interrupts
may be disabled (Remi Pommarel)
- Fix Aardvark big-endian support (Grzegorz Jaszczyk)
- Fix bridge emulation big-endian support (Grzegorz Jaszczyk)
* remotes/lorenzo/pci/aardvark:
PCI: pci-bridge-emul: Fix big-endian support
PCI: aardvark: Fix big endian support
PCI: aardvark: Don't rely on jiffies while holding spinlock
PCI: aardvark: Fix PCI_EXP_RTCTL register configuration
PCI: aardvark: Wait for endpoint to be ready before training link
PCI: aardvark: Use LTSSM state to build link training flag
- Protect pci_reassign_bridge_resources() against concurrent
addition/removal (Benjamin Herrenschmidt)
- Fix bridge dma_ranges resource list cleanup (Rob Herring)
- Add PCI_STD_NUM_BARS for the number of standard BARs (Denis Efremov)
- Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters to control the
MMIO and prefetchable MMIO window sizes of hotplug bridges
independently (Nicholas Johnson)
- Fix MMIO/MMIO_PREF window assignment that assigned more space than
desired (Nicholas Johnson)
- Only enforce bus numbers from bridge EA if the bridge has EA devices
downstream (Subbaraya Sundeep)
* pci/resource:
PCI: Do not use bus number zero from EA capability
PCI: Avoid double hpmemsize MMIO window assignment
PCI: Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters
PCI: Add PCI_STD_NUM_BARS for the number of standard BARs
PCI: Fix missing bridge dma_ranges resource list cleanup
PCI: Protect pci_reassign_bridge_resources() against concurrent addition/removal
With the recent 59bb47985c ("mm, sl[aou]b: guarantee natural
alignment for kmalloc(power-of-two)"), kzalloc() is able to allocate
a 4KB buffer that is guaranteed to be 4KB-aligned. Here the size and
alignment of hbus is important because hbus's field
retarget_msi_interrupt_params must not cross a 4KB page boundary.
Here we prefer kzalloc to get_zeroed_page(), because a buffer
allocated by the latter is not tracked and scanned by kmemleak, and
hence kmemleak reports the pointer contained in the hbus buffer
(i.e. the hpdev struct, which is created in new_pcichild_device() and
is tracked by hbus->children) as memory leak (false positive).
If the kernel doesn't have 59bb47985c, get_zeroed_page() *must* be
used to allocate the hbus buffer and we can avoid the kmemleak false
positive by using kmemleak_alloc() and kmemleak_free() to ask
kmemleak to track and scan the hbus buffer.
Reported-by: Lili Deng <v-lide@microsoft.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
A VM can have multiple Hyper-V hbus. It's incorrect to set the global
variable 'pci_protocol_version' when *every* hbus is initialized in
hv_pci_protocol_negotiation(). This is not an issue in practice since
every hbus should have the same value of hbus->protocol_version, but
we should make the variable per-hbus, so in case we have busses
with different protocol versions, the driver can still work correctly.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Add suspend() and resume() functions so that Hyper-V virtual PCI devices
are handled properly when the VM hibernates and resumes from
hibernation.
Note that the suspend() function must make sure there are no pending
work items before calling vmbus_close(), since it runs in a process
context as a callback in dpm_suspend(). When it starts to run, the
channel callback hv_pci_onchannelcallback(), which runs in a tasklet
context, can be still running concurrently and scheduling new work items
onto hbus->wq in hv_pci_devices_present() and hv_pci_eject_device(), and
the work item handlers can access the vmbus channel, which can be being
closed by hv_pci_suspend(), e.g. the work item handler
pci_devices_present_work() -> new_pcichild_device() writes to the vmbus
channel.
To eliminate the race, hv_pci_suspend() disables the channel callback
tasklet, sets hbus->state to hv_pcibus_removing, and re-enables the
tasklet. This way, when hv_pci_suspend() proceeds, it knows that no new
work item can be scheduled, and then it flushes hbus->wq and safely
closes the vmbus channel.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
There is no functional change. This is just preparatory for a later
patch which adds the hibernation support for the pci-hyperv driver.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
[bhelgaas: do same in vmd.c]
Link: https://lore.kernel.org/r/20191120134036.14502-1-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Set the mode register to host(RC) mode so that the host controller
mode is set-up consistently across SoCs.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
[lorenzo.pieralisi@arm.com: updated log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Remove <linux/pci.h> and <linux/msi.h> from being included directly as part
of the include/linux/of_pci.h, and remove superfluous declaration of struct
of_phandle_args.
Move users of include <linux/of_pci.h> to include <linux/pci.h> and
<linux/msi.h> directly rather than rely on both being included transitively
through <linux/of_pci.h>.
Link: https://lore.kernel.org/r/20190903113059.2901-1-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Change:
drivers/pci/controller/pcie-cadence.h
drivers/pci/controller/pcie-rockchip.h
to use the correct SPDX comment style per section 2 of
Documentation/process/license-rules.rst.
These resolve the following checkpatch.pl warning:
WARNING: Missing or malformed SPDX-License-Identifier tag in line 1
[bhelgaas: split to separate patch]
Link: https://lore.kernel.org/r/20190828135322.10370-1-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The 0V9 and 1V8 supplies power the PCIe block in the SoC itself, and
are thus fundamental to PCIe being usable at all. As such, it makes
sense to treat them as non-optional and rely on dummy regulators if
not explicitly described.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Now that the helpers provide the inbound resources in the host bridge
'dma_ranges' resource list, convert Renesas R-Car PCIe host bridge to
use the resource list to setup the inbound addresses.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Now that the helpers provide the inbound resources in the host bridge
'dma_ranges' resource list, convert Broadcom iProc host bridge to use
the resource list to setup the inbound addresses.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Now that the helpers provide the inbound resources in the host bridge
'dma_ranges' resource list, convert the Xgene host bridge to use the
resource list to setup the inbound addresses.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Toan Le <toan@os.amperecomputing.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Now that the helpers provide the inbound resources in the host bridge
'dma_ranges' resource list, convert the v3-semi host bridge to use
the resource list to setup the inbound addresses.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Now that the helpers provide the inbound resources in the host bridge
'dma_ranges' resource list, convert Faraday ftpci100 host bridge to use
the resource list to setup the inbound addresses.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Extend devm_of_pci_get_host_bridge_resources() and
pci_parse_request_of_pci_ranges() helpers to also parse the inbound
addresses from DT 'dma-ranges' and populate a resource list with the
translated addresses. This will help ensure 'dma-ranges' is always
parsed in a consistent way.
Tested-by: Srinath Mannam <srinath.mannam@broadcom.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com> # for AArdvark
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Srinath Mannam <srinath.mannam@broadcom.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Will Deacon <will@kernel.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Toan Le <toan@os.amperecomputing.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Tom Joseph <tjoseph@cadence.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: Ryder Lee <ryder.lee@mediatek.com>
Cc: Karthikeyan Mitran <m.karthikeyan@mobiveil.co.in>
Cc: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: rfi@lists.rocketboards.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
This patch adds support for this VMD device which supports the bus
restriction mode.
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
VMD bus restrictions are required when IO fabric is multiplexed such
that VMD cannot use the entire bus range. This patch adds another bus
restriction decode bit that can be set by firmware to restrict the VMD
bus range to between 224-255.
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The R-Car Gen2/3 manual - available at:
https://www.renesas.com/eu/en/products/microcontrollers-microprocessors/rz/rzg/rzg1m.html#documents
"RZ/G Series User's Manual: Hardware" section
strictly enforces the MACCTLR inizialization value - 39.3.1 - "Initial
Setting of PCI Express":
"Be sure to write the initial value (= H'80FF 0000) to MACCTLR before
enabling PCIETCTLR.CFINIT".
To avoid unexpected behavior and to match the SW initialization sequence
guidelines, this patch programs the MACCTLR with the correct value.
Note that the MACCTLR.SPCHG bit in the MACCTLR register description
reports that "Only writing 1 is valid and writing 0 is invalid" but this
"invalid" has to be interpreted as a write-ignore aka "ignored", not
"prohibited".
Reported-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Fixes: c25da47788 ("PCI: rcar: Add Renesas R-Car PCIe driver")
Fixes: be20bbcb0a ("PCI: rcar: Add the initialization of PCIe link in resume_noirq()")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: <stable@vger.kernel.org> # v5.2+
Cadence core library files may be used by various platform drivers.
Add a new directory "cadence" to group all the Cadence core library files
and the platforms using Cadence core library.
Signed-off-by: Tom Joseph <tjoseph@cadence.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cadence PCIe host and endpoint IP may be embedded into a variety of
SoCs/platforms. Let's extract the platform related APIs/Structures in the
current driver to a separate file (pcie-cadence-plat.c), such that the
common functionality can be used by future platforms.
Signed-off-by: Tom Joseph <tjoseph@cadence.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Due to hardware constraints, the size of each inbound range entry
populated into the controller cannot be larger than the alignment
of the entry's start address. Currently, the alignment for each
"dma-ranges" inbound range is calculated only once for each range
and the increment for programming the controller is also derived
from it only once. Thus, a "dma-ranges" entry describing a memory
at 0x48000000 and size 0x38000000 would lead to multiple controller
entries, each 0x08000000 long.
This is inefficient, especially considering that by adding the size
to the start address, the alignment increases. This patch moves the
alignment calculation into the loop populating the controller entries,
thus updating the alignment for each controller entry.
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: linux-renesas-soc@vger.kernel.org
Since the 'idx' variable value is stored across multiple calls to
rcar_pcie_inbound_ranges() function, and the 'idx' value is used to
index registers which are written, subsequent calls might cause
the 'idx' value to be high enough to trigger writes into nonexistent
registers.
Fix this by moving the 'idx' value check to the beginning of the loop.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: linux-renesas-soc@vger.kernel.org
Remove unnecessary header include (../pci.h) since it doesn't
provide any needed symbols.
Signed-off-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add support for the LS1028a PCIe controller.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <Andrew.Murray@arm.com>
Acked-by: Minghuan Lian <minghuan.Lian@nxp.com>
Since commit a574795bc3 ("PCI: generic,versatile: Remove unused
pci_sys_data structures") the build dependency on ARM is gone, so let's
enable COMPILE_TEST for versatile.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
PHYS_OFFSET is not universally defined on all arches and using it prevents
enabling COMPILE_TEST. PAGE_OFFSET and __pa() are always available, so use
them to get the physical start of memory address.
This should have probably used 'dma-ranges' to get the address, but we
don't want to force a DT update to do that. At least in QEMU, the SMAP
registers have no effect (or perhaps the only value that is handled is 0).
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <andrew.murray@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Convert ARM Versatile host bridge to use the common
pci_parse_request_of_pci_ranges().
There's no need to assign the resources to a temporary list first. Just
use bridge->windows directly and remove all the temporary list handling.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Convert the xilinx-nwl host bridge to use the common
pci_parse_request_of_pci_ranges().
There's no need to assign the resources to a temporary list first. Just
use bridge->windows directly and remove all the temporary list handling.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <andrew.murray@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Convert the Xilinx host bridge to use the common
pci_parse_request_of_pci_ranges().
There's no need to assign the resources to a temporary list first. Just
use bridge->windows directly and remove all the temporary list handling.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <andrew.murray@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Convert the xgene host bridge to use the common
pci_parse_request_of_pci_ranges().
There's no need to assign the resources to a temporary list first. Just
use bridge->windows directly and remove all the temporary list handling.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Toan Le <toan@os.amperecomputing.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <andrew.murray@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Convert V3 host bridge to use the common
pci_parse_request_of_pci_ranges().
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <andrew.murray@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The Rockchip host bridge driver doesn't need to store outboard resources
in its private struct as they are already stored in struct
pci_host_bridge.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <andrew.murray@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-rockchip@lists.infradead.org
Convert the Rockchip host bridge to use the common
pci_parse_request_of_pci_ranges().
There's no need to assign the resources to a temporary list first. Just
use bridge->windows directly and remove all the temporary list handling.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <andrew.murray@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-rockchip@lists.infradead.org
Convert the Mobiveil host bridge to use the common
pci_parse_request_of_pci_ranges().
There's no need to assign the resources to a temporary list first. Just
use bridge->windows directly and remove all the temporary list handling.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Reviewed-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Cc: Karthikeyan Mitran <m.karthikeyan@mobiveil.co.in>
Cc: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Convert Mediatek host bridge to use the common
pci_parse_request_of_pci_ranges().
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Ryder Lee <ryder.lee@mediatek.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: linux-mediatek@lists.infradead.org
Convert the iProc host bridge to use the common
pci_parse_request_of_pci_ranges().
There's no need to assign the resources to a temporary list, so just use
bridge->windows directly.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Convert the Faraday host bridge to use the common
pci_parse_request_of_pci_ranges().
There's no need to assign the resources to a temporary list first. Just
use bridge->windows directly and remove all the temporary list handling.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Convert the Designware host bridge to use the common
pci_parse_request_of_pci_ranges().
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <andrew.murray@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Convert altera host bridge to use the common
pci_parse_request_of_pci_ranges().
There's no need to assign the resources to a temporary list first. Just
use bridge->windows directly and remove all the temporary list handling.
If an I/O range is present, then it will now be mapped. It's expected
that h/w which doesn't support I/O range will not define one.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: rfi@lists.rocketboards.org
Convert aardvark to use the common pci_parse_request_of_pci_ranges().
There's no need to assign the resources to a temporary list first. Just
use bridge->windows directly and remove all the temporary list handling.
Tested-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Invalidate PAXB inbound/outbound address mapping on probe before
programming it.
Kernel relies on outbound/inbound windows VALID bit in OARR registers to
detect if a window was programmed and if it is set it does not overwrite
it.
This causes issues on soft reboot (eg kexec) since the host controller
does not go through a HW reset on softboot so the kernel detects valid
outbound/inbound windows configuration and is not able to reprogramme
it as expected.
Therefore, in order to make sure outbound/inbound windows are
reprogrammed on soft reboot (eg kexec), invalidate memory windows on
each probe to fix the issue.
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Corrects the programming to provide REFCLK to the downstream device
when there is no CLKREQ sideband signal routing present from root port
to the endpont.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Initialise every multiple-byte field of emulated PCI bridge config
space with proper cpu_to_le* macro. This is required since the structure
describing config space of emulated bridge assumes little-endian
convention.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Fix the return type of mvebu_pcie_map_registers in the
error path to have __iomem on it. Fixes the following
sparse warning:
drivers/pci/controller/pci-mvebu.c:716:31: warning: incorrect type in return expression (different address spaces)
drivers/pci/controller/pci-mvebu.c:716:31: expected void [noderef] <asn:2> *
drivers/pci/controller/pci-mvebu.c:716:31: got void *
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <andrew.murray@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
The mvebu_pci_bridge_emul_ops is not exported outside
of the driver, so make it static to avoid the following
sparse warning:
drivers/pci/controller/pci-mvebu.c:557:28: warning: symbol 'mvebu_pci_bridge_emul_ops' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <andrew.murray@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
find_next_bit() takes a parameter of size long, and performs arithmetic
that assumes that the argument is of size long.
Therefore we cannot pass a u32, since this will cause find_next_bit()
to read outside the stack buffer and will produce the following print:
BUG: KASAN: stack-out-of-bounds in find_next_bit+0x38/0xb0
Fixes: 1b497e6493 ("PCI: dwc: Fix uninitialized variable in dw_handle_msi_irq()")
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
RISCV has csr_read()/write() macros in arch/riscv/include/asm/csr.h.
The same function naming is used in the PCI mobiveil driver thus
causing build error.
Rename csr_[read,write][l,] to mobiveil_csr_read()/write() to fix it.
drivers/pci/controller/pcie-mobiveil.c:238:69: error: macro "csr_read" passed 3 arguments, but takes just 1
static u32 csr_read(struct mobiveil_pcie *pcie, u32 off, size_t size)
drivers/pci/controller/pcie-mobiveil.c:253:80: error: macro "csr_write" passed 4 arguments, but takes just 2
static void csr_write(struct mobiveil_pcie *pcie, u32 val, u32 off, size_t size)
Fixes: bcbe0d9a8d ("PCI: mobiveil: Unify register accessors")
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Minghuan Lian <Minghuan.Lian@nxp.com>
Cc: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
Cc: Andrew Murray <andrew.murray@arm.com>
Add support for the Amlogic G12A SoC using a separate shared PHY.
This adds support for fetching a PHY phandle and call the PHY init,
reset and power on/off calls instead of writing in the PHY register or
toggling the PHY reset line.
The MIPI clock and the PHY memory resource are only required for the
Amlogic AXG SoC PCIe PHY setup, thus these elements are ignored for
the Amlogic G12A having a separate shared PHY.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Fix the clock names used in the probe function according
to the bindings.
Fixes: 9c0ef6d34f ("PCI: amlogic: Add the Amlogic Meson PCIe controller driver")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Normally asserting reset signal on gpio would be achieved with:
gpiod_set_value_cansleep(reset_gpio, 1);
Meson PCI driver set reset value to '0' instead of '1' as it takes into
account the PERST# signal polarity. The polarity should be taken care
in the device tree instead.
This fixes the reset assertion meaning and moves out the polarity
configuration in DT (please note that there is no DT currently using
this driver).
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
advk_pcie_wait_pio() can be called while holding a spinlock (from
pci_bus_read_config_dword()), then depends on jiffies in order to
timeout while polling on PIO state registers. In the case the PIO
transaction failed, the timeout will never happen and will also cause
the cpu to stall.
This decrements a variable and wait instead of using jiffies.
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
PCI_EXP_RTCTL is used to activate PME interrupt only, so writing into it
should not modify other interrupts' mask. The ISR mask polarity was also
inverted, when PCI_EXP_RTCTL_PMEIE is set PCIE_MSG_PM_PME_MASK mask bit
should actually be cleared.
Fixes: 8a3ebd8de3 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
When configuring pcie reset pin from gpio (e.g. initially set by
u-boot) to pcie function this pin goes low for a brief moment
asserting the PERST# signal. Thus connected device enters fundamental
reset process and link configuration can only begin after a minimal
100ms delay (see [1]).
Because the pin configuration comes from the "default" pinctrl it is
implicitly configured before the probe callback is called:
driver_probe_device()
really_probe()
...
pinctrl_bind_pins() /* Here pin goes from gpio to PCIE reset
function and PERST# is asserted */
...
drv->probe()
[1] "PCI Express Base Specification", REV. 4.0
PCI Express, February 19 2014, 6.6.1 Conventional Reset
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Aardvark's PCI_EXP_LNKSTA_LT flag in its link status register is not
implemented and does not reflect the actual link training state (the
flag is always set to 0). In order to support link re-training feature
this flag has to be emulated. The Link Training and Status State
Machine (LTSSM) flag in Aardvark LMI config register could be used as
a link training indicator. Indeed if the LTSSM is in L0 or upper state
then link training has completed (see [1]).
Unfortunately because after asking a link retraining it takes a while
for the LTSSM state to become less than 0x10 (due to L0s to recovery
state transition delays), LTSSM can still be in L0 while link training
has not finished yet. So this waits for link to be in recovery or lesser
state before returning after asking for a link retrain.
[1] "PCI Express Base Specification", REV. 4.0
PCI Express, February 19 2014, Table 4-14
Fixes: 8a3ebd8de3 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Tested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Code that iterates over all standard PCI BARs typically uses
PCI_STD_RESOURCE_END. However, that requires the unusual test
"i <= PCI_STD_RESOURCE_END" rather than something the typical
"i < PCI_STD_NUM_BARS".
Add a definition for PCI_STD_NUM_BARS and change loops to use the more
idiomatic C style to help avoid fencepost errors.
Link: https://lore.kernel.org/r/20190927234026.23342-1-efremov@linux.com
Link: https://lore.kernel.org/r/20190927234308.23935-1-efremov@linux.com
Link: https://lore.kernel.org/r/20190916204158.6889-3-efremov@linux.com
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Sebastian Ott <sebott@linux.ibm.com> # arch/s390/
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> # video/fbdev/
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com> # pci/controller/dwc/
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com> # scsi/pm8001/
Acked-by: Martin K. Petersen <martin.petersen@oracle.com> # scsi/pm8001/
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # memstick/
- Fix Tegra OF node reference leak (Nishka Dasgupta)
- Add #defines for PCIe Data Link Feature and Physical Layer 16.0 GT/s
features (Vidya Sagar)
- Disable MSI for Tegra Root Ports since they don't support using MSI for
all Root Port events (Vidya Sagar)
- Group DesignWare write-protected register writes together (Vidya Sagar)
- Move DesignWare capability search interfaces so they can be used by
both host and endpoint drivers (Vidya Sagar)
- Add DesignWare extended capability search interfaces (Vidya Sagar)
- Export dw_pcie_wait_for_link() so drivers can be modules (Vidya Sagar)
- Add "snps,enable-cdm-check" DT binding for Configuration Dependent
Module (CDM) register checking (Vidya Sagar)
- Add DesignWare support for "snps,enable-cdm-check" CDM checking (Vidya
Sagar)
- Add "supports-clkreq" DT binding for host drivers to decide whether to
advertise low power features (Vidya Sagar)
- Add DT binding for Tegra194 (Vidya Sagar)
- Add DT binding for Tegra194 P2U (PIPE to UPHY) block (Vidya Sagar)
- Add support for Tegra194 P2U (PIPE to UPHY) (Vidya Sagar)
- Add support for Tegra194 host controller (Vidya Sagar)
- Add Tegra support for sideband PERST# and CLKREQ# for C5 (Vidya Sagar)
- Add Tegra support for slot regulators for p2972-0000 platform (Vidya
Sagar)
* lorenzo/pci/tegra:
arm64: tegra: Add PCIe slot supply information in p2972-0000 platform
arm64: tegra: Add configuration for PCIe C5 sideband signals
PCI: tegra: Add support to enable slot regulators
PCI: tegra: Add support to configure sideband pins
dt-bindings: PCI: tegra: Add PCIe slot supplies regulator entries
dt-bindings: PCI: tegra: Add sideband pins configuration entries
PCI: tegra: Add Tegra194 PCIe support
phy: tegra: Add PCIe PIPE2UPHY support
dt-bindings: PHY: P2U: Add Tegra194 P2U block
dt-bindings: PCI: tegra: Add device tree support for Tegra194
dt-bindings: Add PCIe supports-clkreq property
PCI: dwc: Add support to enable CDM register check
dt-bindings: PCI: designware: Add binding for CDM register check
PCI: dwc: Export dw_pcie_wait_for_link() API
PCI: dwc: Add extended configuration space capability search API
PCI: dwc: Move config space capability search API
PCI: dwc: Group DBI registers writes requiring unlocking
PCI: Disable MSI for Tegra root ports
PCI: Add #defines for some of PCIe spec r4.0 features
PCI: tegra: Fix OF node reference leak
- Fix mobiveil inbound window CPU base address setup (Hou Zhiqiang)
* remotes/lorenzo/pci/mobiveil:
PCI: mobiveil: Fix the CPU base address setup in inbound window
- Propagate regulator_get_optional() errors so callers can distinguish
real errors from optional regulators that are absent (Thierry Reding)
- Propagate devm_of_phy_get() errors so callers can distinguish
real errors from optional PHYs that are absent (Thierry Reding)
- Add Andrew Murray as PCI native driver reviewer (Lorenzo Pieralisi)
* remotes/lorenzo/pci/misc:
MAINTAINERS: Add PCI native host/endpoint controllers designated reviewer
PCI: iproc: Propagate errors for optional PHYs
PCI: histb: Propagate errors for optional regulators
PCI: armada8x: Propagate errors for optional PHYs
PCI: imx6: Propagate errors for optional regulators
PCI: exynos: Propagate errors for optional PHYs
PCI: rockchip: Propagate errors for optional regulators
- Add mediatek support for MT7629 (Jianjun Wang)
* remotes/lorenzo/pci/mediatek:
PCI: mediatek: Add controller support for MT7629
dt-bindings: PCI: Add support for MT7629
- Mark Layerscape endpoint BARs 2 and 4 as 64-bit (Xiaowei Bao)
- Add CONFIG_PCI_LAYERSCAPE_EP so EP/RC can be built separately (Xiaowei
Bao)
* remotes/lorenzo/pci/layerscape:
PCI: layerscape: Add CONFIG_PCI_LAYERSCAPE_EP to build EP/RC separately
PCI: layerscape: Add the bar_fixed_64bit property to the endpoint driver
- Fix Hyper-V use-after-free in pci_dev removal (Dexuan Cui)
- Fix Hyper-V build error in non-sysfs config (Randy Dunlap)
- Reallocate to avoid Hyper-V domain number collisions (Haiyang Zhang)
- Use Hyper-V instance ID bytes 4-5 to reduce domain collisions (Haiyang
Zhang)
* remotes/lorenzo/pci/hv:
PCI: hv: Use bytes 4 and 5 from instance ID as the PCI domain numbers
PCI: hv: Detect and fix Hyper-V PCI domain number collision
PCI: pci-hyperv: Fix build errors on non-SYSFS config
PCI: hv: Avoid use of hv_pci_dev->pci_slot after freeing it
- Make kirin_dw_pcie_ops constant (Nishka Dasgupta)
- Make DesignWare "num-lanes" property optional and remove from relevant
DTs (Hou Zhiqiang)
* remotes/lorenzo/pci/dwc:
arm64: dts: fsl: Remove num-lanes property from PCIe nodes
ARM: dts: ls1021a: Remove num-lanes property from PCIe nodes
PCI: dwc: Return directly when num-lanes is not found
dt-bindings: PCI: designware: Remove the num-lanes from Required properties
PCI: kirin: Make structure kirin_dw_pcie_ops constant
Add support to get regulator information of 3.3V and 12V supplies of a PCIe
slot from the respective controller's device-tree node and enable those
supplies. This is required in platforms like p2972-0000 where the supplies
to x16 slot owned by C5 controller need to be enabled before attempting to
enumerate the devices.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Add support to configure sideband signal pins when the information is
present in the respective controller device-tree node.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
[bhelgaas: fold in YueHaibing's fix for build error without CONFIG_PINCTRL;
https://lore.kernel.org/r/20190920014807.38288-1-yuehaibing@huawei.com]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Pull networking updates from David Miller:
1) Support IPV6 RA Captive Portal Identifier, from Maciej Żenczykowski.
2) Use bio_vec in the networking instead of custom skb_frag_t, from
Matthew Wilcox.
3) Make use of xmit_more in r8169 driver, from Heiner Kallweit.
4) Add devmap_hash to xdp, from Toke Høiland-Jørgensen.
5) Support all variants of 5750X bnxt_en chips, from Michael Chan.
6) More RTNL avoidance work in the core and mlx5 driver, from Vlad
Buslov.
7) Add TCP syn cookies bpf helper, from Petar Penkov.
8) Add 'nettest' to selftests and use it, from David Ahern.
9) Add extack support to drop_monitor, add packet alert mode and
support for HW drops, from Ido Schimmel.
10) Add VLAN offload to stmmac, from Jose Abreu.
11) Lots of devm_platform_ioremap_resource() conversions, from
YueHaibing.
12) Add IONIC driver, from Shannon Nelson.
13) Several kTLS cleanups, from Jakub Kicinski.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1930 commits)
mlxsw: spectrum_buffers: Add the ability to query the CPU port's shared buffer
mlxsw: spectrum: Register CPU port with devlink
mlxsw: spectrum_buffers: Prevent changing CPU port's configuration
net: ena: fix incorrect update of intr_delay_resolution
net: ena: fix retrieval of nonadaptive interrupt moderation intervals
net: ena: fix update of interrupt moderation register
net: ena: remove all old adaptive rx interrupt moderation code from ena_com
net: ena: remove ena_restore_ethtool_params() and relevant fields
net: ena: remove old adaptive interrupt moderation code from ena_netdev
net: ena: remove code duplication in ena_com_update_nonadaptive_moderation_interval _*()
net: ena: enable the interrupt_moderation in driver_supported_features
net: ena: reimplement set/get_coalesce()
net: ena: switch to dim algorithm for rx adaptive interrupt moderation
net: ena: add intr_moder_rx_interval to struct ena_com_dev and use it
net: phy: adin: implement Energy Detect Powerdown mode via phy-tunable
ethtool: implement Energy Detect Powerdown support via phy-tunable
xen-netfront: do not assume sk_buff_head list is empty in error handling
s390/ctcm: Delete unnecessary checks before the macro call “dev_kfree_skb”
net: ena: don't wake up tx queue when down
drop_monitor: Better sanitize notified packets
...
The shadow offset scratchpad was moved to 0x2000-0x2010. Update the
location to get the correct shadow offset.
Fixes: 6788958e4f ("PCI: vmd: Assign membar addresses from shadow registers")
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org # v5.2+
VMD maps child device config spaces to the VMD Config BAR linearly
regardless of the starting bus offset. Because of this, the config
address decode must ignore starting bus offsets when mapping the BDF to
the config space address.
Fixes: 2a5a9c9a20 ("PCI: vmd: Add offset to bus numbers if necessary")
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org # v5.2+
Some PCIe controllers can be set to either Host or EP according to some
early boot FW. To make sure there is no discrepancy (e.g. FW configured
the port to EP mode while the DT specifies it as a host bridge or vice
versa), a check has been added for each mode.
Signed-off-by: Jonathan Chocron <jonnyc@amazon.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
This driver is DT based and utilizes the DesignWare APIs.
It allows using a smaller ECAM range for a larger bus range -
usually an entire bus uses 1MB of address space, but the driver
can use it for a larger number of buses. This is achieved by using a HW
mechanism which allows changing the BUS part of the "final" outgoing
config transaction. There are 2 HW regs, one which is basically a
bitmask determining which bits to take from the AXI transaction itself
and another which holds the complementary part programmed by the
driver.
All link initializations are handled by the boot FW.
Signed-off-by: Jonathan Chocron <jonnyc@amazon.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
As recommended by Azure host team, the bytes 4, 5 have more uniqueness
(info entropy) than bytes 8, 9 so use them as the PCI domain numbers.
On older hosts, bytes 4, 5 can also be used -- no backward compatibility
issues are introduced and the chance of collision is greatly reduced.
In the rare cases of collision, the driver code detects and finds
another number that is not in use.
Suggested-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Sasha Levin <sashal@kernel.org>
Add support for Synopsys DesignWare core IP based PCIe host controller
present in the Tegra194 SoC.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
devm_phy_get() can fail for a number of reasons besides probe deferral.
It can for example return -ENOMEM if it runs out of memory as it tries
to allocate devres structures. Propagating only -EPROBE_DEFER is
problematic because it results in these legitimately fatal errors being
treated as "PHY not specified in DT".
What we really want is to ignore the optional PHYs only if they have not
been specified in DT. devm_phy_optional_get() is a function that exactly
does what's required here, so use that instead.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
regulator_get_optional() can fail for a number of reasons besides probe
deferral. It can for example return -ENOMEM if it runs out of memory as
it tries to allocate data structures. Propagating only -EPROBE_DEFER is
problematic because it results in these legitimately fatal errors being
treated as "regulator not specified in DT".
What we really want is to ignore the optional regulators only if they
have not been specified in DT. regulator_get_optional() returns -ENODEV
in this case, so that's the special case that we need to handle. So we
propagate all errors, except -ENODEV, so that real failures will still
cause the driver to fail probe.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
devm_of_phy_get_by_index() can fail for a number of reasons besides
probe deferral. It can for example return -ENOMEM if it runs out of
memory as it tries to allocate devres structures. Propagating only
-EPROBE_DEFER is problematic because it results in these legitimately
fatal errors being treated as "PHY not specified in DT".
What we really want is to ignore the optional PHYs only if they have not
been specified in DT. devm_of_phy_get_by_index() returns -ENODEV in this
case, so that's the special case that we need to handle. So we propagate
all errors, except -ENODEV, so that real failures will still cause the
driver to fail probe.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
regulator_get_optional() can fail for a number of reasons besides probe
deferral. It can for example return -ENOMEM if it runs out of memory as
it tries to allocate data structures. Propagating only -EPROBE_DEFER is
problematic because it results in these legitimately fatal errors being
treated as "regulator not specified in DT".
What we really want is to ignore the optional regulators only if they
have not been specified in DT. regulator_get_optional() returns -ENODEV
in this case, so that's the special case that we need to handle. So we
propagate all errors, except -ENODEV, so that real failures will still
cause the driver to fail probe.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: kernel@pengutronix.de
Cc: linux-imx@nxp.com
devm_of_phy_get() can fail for a number of reasons besides probe
deferral. It can for example return -ENOMEM if it runs out of memory as
it tries to allocate devres structures. Propagating only -EPROBE_DEFER
is problematic because it results in these legitimately fatal errors
being treated as "PHY not specified in DT".
What we really want is to ignore the optional PHYs only if they have not
been specified in DT. devm_of_phy_get() returns -ENODEV in this case, so
that's the special case that we need to handle. So we propagate all
errors, except -ENODEV, so that real failures will still cause the
driver to fail probe.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
