Some STB chips have a special purpose reset controller named RESCAL (reset
calibration). The PCIe HW can now control RESCAL to start and stop its
operation. On probe(), the RESCAL is deasserted and the driver goes
through the sequence of setting registers and reading status in order to
start the internal PHY that is required for the PCIe.
Link: https://lore.kernel.org/r/20200911175232.19016-7-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
pci_restore_msi_state() directly writes the MSI/MSI-X related registers
via MMIO. On a physical machine, this works perfectly; for a Linux VM
running on a hypervisor, which typically enables IOMMU interrupt remapping,
the hypervisor usually should trap and emulate the MMIO accesses in order
to re-create the necessary interrupt remapping table entries in the IOMMU,
otherwise the interrupts can not work in the VM after hibernation.
Hyper-V is different from other hypervisors in that it does not trap and
emulate the MMIO accesses, and instead it uses a para-virtualized method,
which requires the VM to call hv_compose_msi_msg() to notify the hypervisor
of the info that would be passed to the hypervisor in the case of the
trap-and-emulate method. This is not an issue to a lot of PCI device
drivers, which destroy and re-create the interrupts across hibernation, so
hv_compose_msi_msg() is called automatically. However, some PCI device
drivers (e.g. the in-tree GPU driver nouveau and the out-of-tree Nvidia
proprietary GPU driver) do not destroy and re-create MSI/MSI-X interrupts
across hibernation, so hv_pci_resume() has to call hv_compose_msi_msg(),
otherwise the PCI device drivers can no longer receive interrupts after
the VM resumes from hibernation.
Hyper-V is also different in that chip->irq_unmask() may fail in a
Linux VM running on Hyper-V (on a physical machine, chip->irq_unmask()
can not fail because unmasking an MSI/MSI-X register just means an MMIO
write): during hibernation, when a CPU is offlined, the kernel tries
to move the interrupt to the remaining CPUs that haven't been offlined
yet. In this case, hv_irq_unmask() -> hv_do_hypercall() always fails
because the vmbus channel has been closed: here the early "return" in
hv_irq_unmask() means the pci_msi_unmask_irq() is not called, i.e. the
desc->masked remains "true", so later after hibernation, the MSI interrupt
always remains masked, which is incorrect. Refer to cpu_disable_common()
-> fixup_irqs() -> irq_migrate_all_off_this_cpu() -> migrate_one_irq():
static bool migrate_one_irq(struct irq_desc *desc)
{
...
if (maskchip && chip->irq_mask)
chip->irq_mask(d);
...
err = irq_do_set_affinity(d, affinity, false);
...
if (maskchip && chip->irq_unmask)
chip->irq_unmask(d);
Fix the issue by calling pci_msi_unmask_irq() unconditionally in
hv_irq_unmask(). Also suppress the error message for hibernation because
the hypercall failure during hibernation does not matter (at this time
all the devices have been frozen). Note: the correct affinity info is
still updated into the irqdata data structure in migrate_one_irq() ->
irq_do_set_affinity() -> hv_set_affinity(), so later when the VM
resumes, hv_pci_restore_msi_state() is able to correctly restore
the interrupt with the correct affinity.
Link: https://lore.kernel.org/r/20201002085158.9168-1-decui@microsoft.com
Fixes: ac82fc8327 ("PCI: hv: Add hibernation support")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Jake Oshins <jakeo@microsoft.com>
PCI host bridge driver can be probed before the gpiochip it requires,
so, of_get_named_gpio() can return -EPROBE_DEFER. Current code lets the
kirin_pcie_probe() directly return -ENODEV, which results in the PCI
host controller driver probe failure; with this error code the PCI host
controller driver will not be probed again when the gpiochip driver is
loaded.
Fix the above issue by letting kirin_pcie_probe() return -EPROBE_DEFER in
such a case.
Link: https://lore.kernel.org/r/20200918123800.19983-1-huobean@gmail.com
Signed-off-by: Bean Huo <beanhuo@micron.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Use DEFINE_SEQ_ATTRIBUTE macro to simplify the code.
Link: https://lore.kernel.org/r/20200916025025.3992783-1-liushixin2@huawei.com
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Add missing documentation for the parameter "version" and "num_version"
of the hv_pci_protocol_negotiation() function and resolve build time
kernel-doc warnings:
drivers/pci/controller/pci-hyperv.c:2535: warning: Function parameter
or member 'version' not described in 'hv_pci_protocol_negotiation'
drivers/pci/controller/pci-hyperv.c:2535: warning: Function parameter
or member 'num_version' not described in 'hv_pci_protocol_negotiation'
No change to functionality intended.
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Link: https://lore.kernel.org/r/20200925234753.1767227-1-kw@linux.com
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Add PCIe EP mode support for ls1088a and ls2088a, there are some
difference between LS1 and LS2 platform, so refactor the code of
the EP driver.
Link: https://lore.kernel.org/r/20200918080024.13639-10-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
dw_pcie_ep_raise_msix_irq was never called in the exisitng driver
before, because the ls1046a platform don't support the MSIX feature
and msix_capable was always set to false.
Now that add the ls1088a platform with MSIX support, use the doorbell
method to support the MSIX feature.
Link: https://lore.kernel.org/r/20200918080024.13639-9-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
The different PCIe controller in one board may be have different
capability of MSI or MSIX, so change the way of getting the MSI
capability, make it more flexible.
Link: https://lore.kernel.org/r/20200918080024.13639-8-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Fix some format issue of the code in EP driver.
Link: https://lore.kernel.org/r/20200918080024.13639-7-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Each PF of EP device should have its own MSI or MSIX capabitily
struct, so create a dw_pcie_ep_func struct and move the msi_cap
and msix_cap to this struct from dw_pcie_ep, and manage the PFs
via a list.
Link: https://lore.kernel.org/r/20200918080024.13639-5-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Move the function of getting MSI capability to the front of init
function, because the init function of the EP platform driver will use
the return value by the function of getting MSI capability.
Link: https://lore.kernel.org/r/20200918080024.13639-4-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Add the doorbell mode of MSI-X in DWC EP driver.
Link: https://lore.kernel.org/r/20200918080024.13639-3-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Add multiple PFs support for DWC, due to different PF have different
config space, we use func_conf_select callback function to access
the different PF's config space, the different chip company need to
implement this callback function when use the DWC IP core and intend
to support multiple PFs feature.
Link: https://lore.kernel.org/r/20200918080024.13639-2-Zhiqiang.Hou@nxp.com
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
The PERST# bit was moved to a different register in 7278-type STB chips.
In addition, the polarity of the bit was also changed; for other chips
writing a 1 specified assert; for 7278-type chips, writing a 0 specifies
assert. Of course, PERST# is a PCIe asserted-low signal.
While we are here, also change the bridge_sw_init_set() functions so like
the perst_set() functions they are chip specific and we no longer rely on
data wrt chip specific field mask and shift values.
Link: https://lore.kernel.org/r/20200911175232.19016-6-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Broadcom Set-top (BrcmSTB) boards typically support S2, S3, and S5 suspend
and resume. Now the PCIe driver may do so as well.
Link: https://lore.kernel.org/r/20200911175232.19016-5-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Add in compatibility strings and code for three Broadcom STB chips. Some
of the register locations, shifts, and masks are different for certain
chips, requiring the use of different constants based on of_id.
We would like to add the following at this time to the match list but we
need to wait until the end of this patchset so that everything works.
{ .compatible = "brcm,bcm7211-pcie", .data = &generic_cfg },
{ .compatible = "brcm,bcm7278-pcie", .data = &bcm7278_cfg },
{ .compatible = "brcm,bcm7216-pcie", .data = &bcm7278_cfg },
{ .compatible = "brcm,bcm7445-pcie", .data = &generic_cfg },
Link: https://lore.kernel.org/r/20200911175232.19016-4-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Have PCIE_BRCMSTB depend on ARCH_BRCMSTB. Also set the default value to
ARCH_BRCMSTB.
Link: https://lore.kernel.org/r/20200911175232.19016-2-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
The arch_.*_msi_irq[s] fallbacks are compiled in whether an architecture
requires them or not. Architectures which are fully utilizing hierarchical
irq domains should never call into that code.
It's not only architectures which depend on that by implementing one or
more of the weak functions, there is also a bunch of drivers which relies
on the weak functions which invoke msi_controller::setup_irq[s] and
msi_controller::teardown_irq.
Make the architectures and drivers which rely on them select them in Kconfig
and if not selected replace them by stub functions which emit a warning and
fail the PCI/MSI interrupt allocation.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20200826112333.992429909@linutronix.de
Devices on the VMD bus use their own MSI irq domain, but it is not
distinguishable from regular PCI/MSI irq domains. This is required
to exclude VMD devices from getting the irq domain pointer set by
interrupt remapping.
Override the default bus token.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200826112333.047315047@linutronix.de
pci_msi_get_hwirq() and pci_msi_set_desc are not longer special. Enable the
generic MSI domain ops in the core and PCI MSI code unconditionally and get
rid of the x86 specific implementations in the X86 MSI code and in the
hyperv PCI driver.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200826112332.564274859@linutronix.de
Convert the interrupt remap drivers to retrieve the pci device from the msi
descriptor and use info::hwirq.
This is the first step to prepare x86 for using the generic MSI domain ops.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Wei Liu <wei.liu@kernel.org>
Acked-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200826112332.466405395@linutronix.de
VMD has it's own PCI/MSI interrupt domain which is not in any way depending
on the x86 vector domain. PCI devices behind VMD share the VMD MSIX vector
entries via a VMD specific message translation to the actual VMD MSIX
vector. The VMD device interrupt handler for the VMD MSIX vectors invokes
all interrupt handlers of the devices which share a vector.
Making the x86 vector domain the actual parent of the VMD irq domain is
pointless and actually counterproductive. When a device interrupt is
requested then it will activate the interrupt which traverses down the
hierarchy and consumes an interrupt vector in the vector domain which is
never used.
The domain is self contained and has no parent dependencies, so just hand
in NULL for the parent and be done with it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20200826112330.928952181@linutronix.de
The HiSilicon HIP PCIe controller is capable of handling errors
on root port and performing port reset separately at each root port.
Add error handling driver for HIP PCIe controller to log
and report recoverable errors. Perform root port reset and restore
link status after the recovery.
Following are some of the PCIe controller's recoverable errors
1. completion transmission timeout error.
2. CRS retry counter over the threshold error.
3. ECC 2 bit errors
4. AXI bresponse/rresponse errors etc.
The driver placed in the drivers/pci/controller/ because the
HIP PCIe controller does not use DWC IP.
Link: https://lore.kernel.org/r/20200903123456.1823-3-shiju.jose@huawei.com
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Convert the remaining cases of register accesses using dbi_base rather
than dw_pcie_(read|write)[bwl]_dbi accessors.
Link: https://lore.kernel.org/r/20200821035420.380495-41-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
The Designware controller has common registers to set number of fast
training sequence ordered sets. The Artpec6, Intel, and Tegra driver
initialize these register fields. Let's move the initialization to the
common setup code and drivers just have to provide the value.
There's a slight change in that the common clock mode N_FTS field is
now initialized. Previously only the Intel driver set this. It's not
clear from the code if common clock mode is used in the Artpec6 or Tegra
driver. It depends on the DWC configuration. Given the field is not
initialized while the others are, it seems unlikely common clock mode
is used.
Link: https://lore.kernel.org/r/20200821035420.380495-40-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
'max_width' is read, but never used, so let's remove it.
Link: https://lore.kernel.org/r/20200821035420.380495-39-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Dilip Kota <eswara.kota@linux.intel.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The PCI_CAP_ID_EXP offset is only needed by intel_pcie_link_setup(), so
let's retrieve it there and avoid storing the offset.
Link: https://lore.kernel.org/r/20200821035420.380495-38-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Dilip Kota <eswara.kota@linux.intel.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
A driver doesn't need to check for DT 'device_type' property, so let's
remove the check.
Link: https://lore.kernel.org/r/20200821035420.380495-37-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Dilip Kota <eswara.kota@linux.intel.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The Intel driver is the only one to set PORT_LINK_DLL_LINK_EN. The
default value is set and it seems pretty certain that enabling link
initialization is always required. Maybe it could just be dropped from
the Intel driver, but lets move setting it into the common code to be
sure.
Link: https://lore.kernel.org/r/20200821035420.380495-36-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Dilip Kota <eswara.kota@linux.intel.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The root bus checks rework in d84c572de1 ("PCI: rockchip: Use
pci_is_root_bus() to check if bus is root bus") caused a regression whereby
in rockchip_pcie_valid_device() if the bus parameter is the root bus and
the dev value == 0, the function should return 1 (ie true) without checking
if the bus->parent pointer is a root bus because that triggers a NULL
pointer dereference.
Fix this by streamlining the root bus detection.
Fixes: d84c572de1 ("PCI: rockchip: Use pci_is_root_bus() to check if bus is root bus")
Link: https://lore.kernel.org/r/20200904140904.944-1-lorenzo.pieralisi@arm.com
Reported-by: Samuel Dionne-Riel <samuel@dionne-riel.com>
Tested-by: Samuel Dionne-Riel <samuel@dionne-riel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
The core interrupt code expects the irq_set_affinity call to update the
effective affinity for the interrupt. This was not being done, so update
iproc_msi_irq_set_affinity() to do so.
Link: https://lore.kernel.org/r/20200803035241.7737-1-mark.tomlinson@alliedtelesis.co.nz
Fixes: 3bc2b23488 ("PCI: iproc: Add iProc PCIe MSI support")
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
The mvebu host controller driver allocates an msi_controller structure
pointer without allocating the structure and initializing its methods,
which makes the pointer useless.
This means that the PCI IRQ MSI layer ignores it and that after all it
should not really be needed.
Remove it.
Link: https://lore.kernel.org/r/20200904142132.6054-1-lorenzo.pieralisi@arm.com
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The ATU registers are only accessed in pcie-designware.c and can be private
to it.
Link: https://lore.kernel.org/r/20200821035420.380495-34-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The DBI2 appears to be write-only and there's no read accesses in the code
anyways, so let's remove all the read_dbi2 related code.
Link: https://lore.kernel.org/r/20200821035420.380495-33-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
The Tegra driver has its own defines for common Designware Port Logic
registers. Convert it to use the standard register definitions.
Link: https://lore.kernel.org/r/20200821035420.380495-32-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
While the Designware controller appears to hard code the PCI_CAP_ID_EXP
capability register at 0x70, there's no need to hard code this in the
driver as it is discoverable.
Link: https://lore.kernel.org/r/20200821035420.380495-31-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Cc: linux-omap@vger.kernel.org
The QCom driver has its own defines for common PCI config space
registers. It also hard codes the capability register offsets which are
discoverable. Convert it to use the standard register definitions.
Link: https://lore.kernel.org/r/20200821035420.380495-30-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-arm-msm@vger.kernel.org
The i.MX6 driver has its own defines for common PCI config space
registers. It also hard codes the capability register offsets which are
discoverable. Convert it to use the standard register definitions.
Link: https://lore.kernel.org/r/20200821035420.380495-29-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
The meson 'elbi' registers are just the Designware 'dbi' space and all
the registers accessed are either standard PCI config space or DWC port
logic registers. Convert the accesses to use the common defines and
register accessors.
Link: https://lore.kernel.org/r/20200821035420.380495-28-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: linux-amlogic@lists.infradead.org
The common Designware init already initializes the RC PCI_COMMAND, BAR0
and BAR1 registers.
The only difference here is the common code sets SERR. If clearing SERR
is what's desired, then the Meson driver should do that instead.
Link: https://lore.kernel.org/r/20200821035420.380495-27-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: linux-amlogic@lists.infradead.org
The meson lanes initialization is the same DWC port logic registers as
in dw_pcie_setup(). We just need to initialize 'num_lanes' to 1 to do
the same init.
dw_pcie_setup_rc() sets the PORT_LOGIC_SPEED_CHANGE bit, so setting it
can be dropped.
Link: https://lore.kernel.org/r/20200821035420.380495-26-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: linux-amlogic@lists.infradead.org
"Fast Link Mode" is a simulation environment speed up setting which should
never be set and the default is not set. However some Amlogic platforms
have it set (by firmware presumably). See commit 87dccf0932 ("PCI:
amlogic: meson: Don't use FAST_LINK_MODE to set up link") for more
information. Let's clear it in core DWC code so we can drop some vendor
specific code.
Link: https://lore.kernel.org/r/20200821035420.380495-25-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Add a 'num_lanes' field to allow drivers to provide a the number of lanes
if not in DT or using a custom DT property. A driver can provide a
non-zero value which is used if the DT doesn't have a 'num-lanes'
property.
Link: https://lore.kernel.org/r/20200821035420.380495-24-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
PCIE_LINK_WIDTH_SPEED_CONTROL is already defined in pcie-designware.h,
so remove it from the i.MX6 driver.
Link: https://lore.kernel.org/r/20200821035420.380495-23-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
The DWC core driver already parses and stores the 'num-viewport' DT
property, so there is no need for the Keystone driver to store it.
Link: https://lore.kernel.org/r/20200821035420.380495-21-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The config space is divided in half for type 0 and type 1 accesses, but
this is pointless as there's only one iATU window which is
reconfigured on each access.
The only platform doing something custom is TI Keystone (surprise!).
It does its own mapping of the config space to avoid spliting the
config space and never actually uses va_cfg1_base as it has its own
config space accessors. With the splitting removed, Keystone can use the
default mapping of config space.
Link: https://lore.kernel.org/r/20200821035420.380495-20-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
The PCI bridge resources are stored in pci_host_bridge.windows, so
there's no need to store them in a DWC specific struct. There's also no
need to parse the resources and store them a 2nd time as they are mainly
used for one time setup of iATU windows.
Link: https://lore.kernel.org/r/20200821035420.380495-19-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jonathan Chocron <jonnyc@amazon.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
The pci_host_bridge struct already has a pointer to its pci_bus, so
let's convert the one user to use the bridge struct and remove the
private 'root_bus' pointer.
Link: https://lore.kernel.org/r/20200821035420.380495-18-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Now that there are no more .scan_bus() callbacks, we can remove it and just
use pci_host_probe().
Link: https://lore.kernel.org/r/20200821035420.380495-17-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
TI keystone is the only Designware driver using .scan_bus(). This
function pointer is the only thing preventing the Designware driver from
using pci_host_probe(). Let's use the pci_ops.add_bus hook instead.
Link: https://lore.kernel.org/r/20200821035420.380495-16-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Now that all the platforms with custom config access handling define
their own pci_ops, let's split the default config accessors to use
different pci_ops for root and child buses. With this, we can use the
generic config accessors. The child bus accesses mainly require a
.map_bus() hook to reconfigure the iATU on each config space access.
Link: https://lore.kernel.org/r/20200821035420.380495-14-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Now that all the drivers needing custom config accessors have been
converted to define their own pci_ops, we can remove the DWC specific
function callbacks {rd,wr}_{own,other}_conf.
Link: https://lore.kernel.org/r/20200821035420.380495-13-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Now that DWC drivers can setup their own pci_ops for the root and child
buses, convert the HiSilicon histb driver to use the standard pci_ops
for root bus config accesses.
Link: https://lore.kernel.org/r/20200821035420.380495-12-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Now that DWC drivers can setup their own pci_ops for the root and child
buses, convert the Samsung Exynos driver to use the standard pci_ops for
root bus config accesses.
Link: https://lore.kernel.org/r/20200821035420.380495-11-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: linux-samsung-soc@vger.kernel.org
Now that DWC drivers can setup their own pci_ops for the root and child
buses, convert the HiSilicon Kirin driver to use the standard pci_ops
for root bus config accesses.
Link: https://lore.kernel.org/r/20200821035420.380495-10-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Xiaowei Song <songxiaowei@hisilicon.com>
Cc: Binghui Wang <wangbinghui@hisilicon.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Now that DWC drivers can setup their own pci_ops for the root and child
buses, convert the Amlogic meson driver to use the standard pci_ops for
root bus config accesses.
Link: https://lore.kernel.org/r/20200821035420.380495-9-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: linux-amlogic@lists.infradead.org
Now that DWC drivers can setup their own pci_ops for the root and child
buses, convert the Tegra driver to use the standard pci_ops for root
bus config accesses.
Link: https://lore.kernel.org/r/20200821035420.380495-8-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Now that DWC drivers can setup their own pci_ops for the root and child
buses, convert the TI Keystone driver to use the standard pci_ops for
config accesses.
Link: https://lore.kernel.org/r/20200821035420.380495-7-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Now that DWC drivers can setup their own pci_ops for the root and child
buses, convert the Amazon driver to use the standard pci_ops for child
bus config accesses.
Link: https://lore.kernel.org/r/20200821035420.380495-6-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jonathan Chocron <jonnyc@amazon.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The Designware root port config space is memory mapped accesses via the
DBI space by default. Add a common implementation
dw_pcie_own_conf_map_bus() for platforms to use.
Link: https://lore.kernel.org/r/20200821035420.380495-5-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
This comment still refers to the old driver pathname,
when all PCI drivers were located directly under the
drivers/pci directory.
Anyway the function name itself is enough, so we can
remove the overabundant path reference.
Link: https://lore.kernel.org/r/20200623074851.7832-1-f.suligoi@asem.it
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
When devm_clk_get() returns -EPROBE_DEFER, i.MX6 PCI driver should
NOT print error message, use dev_err_probe() to handle it.
Link: https://lore.kernel.org/r/1597109364-4739-1-git-send-email-Anson.Huang@nxp.com
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Move code which belongs to link training (delays and resets) into
advk_pcie_train_link() function, so everything related to link training,
including timings is at one place.
After experiments it can be observed that link training in aardvark
hardware is very sensitive to timings and delays, so it is a good idea to
have this code at the same place as link training calls.
This patch does not change behavior of aardvark initialization.
Link: https://lore.kernel.org/r/20200907111038.5811-6-pali@kernel.org
Tested-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Providing driver's 'remove' function allows kernel to bind and unbind devices
from aardvark driver. It also allows to build aardvark driver as a module.
Compiling aardvark as a module simplifies development and debugging of
this driver as it can be reloaded at runtime without the need to reboot
to new kernel.
Link: https://lore.kernel.org/r/20200907111038.5811-5-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Include linux/gpio/consumer.h instead of linux/gpio.h, as is said in the
latter file.
This was reported by kernel test bot when compiling for s390.
drivers/pci/controller/pci-aardvark.c:350:2: error: implicit declaration of function 'gpiod_set_value_cansleep' [-Werror,-Wimplicit-function-declaration]
drivers/pci/controller/pci-aardvark.c:1074:21: error: implicit declaration of function 'devm_gpiod_get_from_of_node' [-Werror,-Wimplicit-function-declaration]
drivers/pci/controller/pci-aardvark.c:1076:14: error: use of undeclared identifier 'GPIOD_OUT_LOW'
Link: https://lore.kernel.org/r/202006211118.LxtENQfl%25lkp@intel.com
Link: https://lore.kernel.org/r/20200907111038.5811-2-pali@kernel.org
Fixes: 5169a9851d ("PCI: aardvark: Issue PERST via GPIO")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Qsdk U-Boot can incorrectly leave the PCIe interface in an undefined
state if bootm command is used instead of bootipq. This is caused by the
not deinit of PCIe when bootm is called. Reset the PCIe before init
anyway to fix this U-Boot bug.
Link: https://lore.kernel.org/r/20200901124955.137-1-ansuelsmth@gmail.com
Fixes: 82a823833f ("PCI: qcom: Add Qualcomm PCIe controller driver")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: stable@vger.kernel.org # v4.19+
Some fields in the host bridge structure are now initialized
by default in the PCI/OF core functions therefore their
initialization in the host controller driver is superfluous.
Remove it.
Link: https://lore.kernel.org/r/20200904142710.8018-1-lorenzo.pieralisi@arm.com
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Rob Herring <robh@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Link: https://lore.kernel.org/r/20200818133739.463193-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Vidya Sagar <vidyas@nvidia.com>
Cc: Andrew Murray <amurray@thegoodpenguin.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-pci@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
In preparation to allow drivers to set their own root and child pci_ops
instead of using the DWC specific config space ops, we need to make
the pci_host_bridge pointer available and move setting the bridge->ops
and bridge->child_ops pointer to before the .host_init() hook.
Link: https://lore.kernel.org/r/20200821035420.380495-4-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The Designware DBI space contains the root bus bridge config space.
Platforms needing custom {rd,wr}_own_conf functions are also the ones
needing custom {read,write}_dbi ops functions and the access sequences
are the same.
Replace all dw_pcie_{rd,wr}_own_conf() calls with the DBI variants in
preparation to remove dw_pcie_{rd,wr}_own_conf().
Link: https://lore.kernel.org/r/20200821035420.380495-3-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The current check will result in the multiple function device
fails to initialize. So fix the check by masking out the
multiple function bit.
Link: https://lore.kernel.org/r/20200818092746.24366-1-Zhiqiang.Hou@nxp.com
Fixes: 0b24134f78 ("PCI: dwc: Add validation that PCIe core is set to correct mode")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl9ML+IeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGA8EIAIy/kTbFS0yrE9yV
hb98oX0z9+EU9YQg9vhaRWwPd+rJF/JMQZLqYcwbhjG9abaUL3T3fEcSAefMHw8E
LAt+hYzA38dHt7tqhsFQX3vV1VorvDVICBVN0yRPRWKKikq4OPIHzaAR9tleGAF5
8btQisl1PjN+obwYmLuNb6aX16OCwAF+uXOwehcoJs9dvMNhwtXRzfOflWzOvOo6
tE0bHErlylLDfLv4ZzEfczTdks4QJZ7C0xLSf3oN9AAynW42Xnhct4hi8qZY/hCf
CMaqeN4hdpub6TvQIqBdDqMMjEXGFgeNSnAEBQY9VpvUqz8NTu6sQxwgJEKDF5tg
d81lv2c=
=uW/F
-----END PGP SIGNATURE-----
Merge 5.9-rc3 into usb-next
We want the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 44331189f9.
Now that the VL805 init routine is run through a reset controller driver
the device dependencies are being taken care of by the device core. No
need to do it manually here.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20200629161845.6021-10-nsaenzjulienne@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Remove redundant logging for platform_get_irq() errors (Krzysztof
Wilczyński)
* pci/irq-error:
PCI: Remove dev_err() when handing an error from platform_get_irq()
- Use pci_host_bridge.windows list directly instead of splicing in a
temporary list for cadence, mvebu, host-common (Rob Herring)
- Use pci_host_probe() instead of open-coding all the pieces for altera,
brcmstb, iproc, mobiveil, rcar, rockchip, tegra, v3, versatile, xgene,
xilinx, xilinx-nwl (Rob Herring)
- Convert to devm_platform_ioremap_resource_byname() instead of open-coding
platform_get_resource_byname() and devm_ioremap_resource() for altera,
cadence, mediatek, rockchip, tegra, xgene (Dejin Zheng)
- Convert to devm_platform_ioremap_resource() instead of open-coding
platform_get_resource() and devm_ioremap_resource() for aardvark,
brcmstb, exynos, ftpci100, versatile (Dejin Zheng)
- Remove redundant error messages from devm_pci_remap_cfg_resource()
callers (Dejin Zheng)
- Drop useless PCI_ENABLE_PROC_DOMAINS from versatile driver (Rob Herring)
- Default host bridge parent device to the platform device (Rob Herring)
- Drop unnecessary zeroing of host bridge fields (Rob Herring)
- Use pci_is_root_bus() instead of tracking root bus number separately in
aardvark, designware (imx6, keystone, designware-host), mobiveil,
xilinx-nwl, xilinx, rockchip, rcar (Rob Herring)
- Set host bridge bus number in pci_scan_root_bus_bridge() instead of each
driver for aardvark, designware-host, host-common, mediatek, rcar, tegra,
v3-semi (Rob Herring)
- Use bridge resources instead of parsing DT 'ranges' again for cadence
(Rob Herring)
- Remove private bus number and range from cadence (Rob Herring)
- Use devm_pci_alloc_host_bridge() to simplify rcar (Rob Herring)
- Use struct pci_host_bridge.windows list directly rather than a temporary
(Rob Herring)
- Reduce OF "missing non-prefetchable window" from error to warning message
(Rob Herring)
- Convert rcar-gen2 from old Arm-specific pci_common_init_dev() to new
arch-independent interfaces (Rob Herring)
- Move DT resource setup into devm_pci_alloc_host_bridge() (Rob Herring)
- Set bridge map_irq and swizzle_irq to default functions; drivers that
don't support legacy IRQs (iproc) need to undo this (Rob Herring)
* pci/host-probe-refactor:
PCI: Set bridge map_irq and swizzle_irq to default functions
PCI: Move DT resource setup into devm_pci_alloc_host_bridge()
PCI: rcar-gen2: Convert to use modern host bridge probe functions
PCI: of: Reduce missing non-prefetchable memory region to a warning
PCI: rcar: Use struct pci_host_bridge.windows list directly
PCI: rcar: Use devm_pci_alloc_host_bridge()
PCI: cadence: Remove private bus number and range storage
PCI: cadence: Use bridge resources for outbound window setup
PCI: Move setting pci_host_bridge.busnr out of host drivers
PCI: rcar: Use pci_is_root_bus() to check if bus is root bus
PCI: rockchip: Use pci_is_root_bus() to check if bus is root bus
PCI: xilinx: Use pci_is_root_bus() to check if bus is root bus
PCI: xilinx-nwl: Use pci_is_root_bus() to check if bus is root bus
PCI: mobiveil: Use pci_is_root_bus() to check if bus is root bus
PCI: designware: Use pci_is_root_bus() to check if bus is root bus
PCI: aardvark: Use pci_is_root_bus() to check if bus is root bus
PCI: Drop unnecessary zeroing of bridge fields
PCI: Set default bridge parent device
PCI: versatile: Drop flag PCI_ENABLE_PROC_DOMAINS
PCI: controller: Remove duplicate error message
PCI: controller: Convert to devm_platform_ioremap_resource()
PCI: controller: Convert to devm_platform_ioremap_resource_byname()
PCI: xilinx: Use pci_host_probe() to register host
PCI: xilinx-nwl: Use pci_host_probe() to register host
PCI: rockchip: Use pci_host_probe() to register host
PCI: rcar: Use pci_host_probe() to register host
PCI: iproc: Use pci_host_probe() to register host
PCI: altera: Use pci_host_probe() to register host
PCI: xgene: Use pci_host_probe() to register host
PCI: versatile: Use pci_host_probe() to register host
PCI: v3: Use pci_host_probe() to register host
PCI: tegra: Use pci_host_probe() to register host
PCI: mobiveil: Use pci_host_probe() to register host
PCI: brcmstb: Use pci_host_probe() to register host
PCI: host-common: Use struct pci_host_bridge.windows list directly
PCI: mvebu: Use struct pci_host_bridge.windows list directly
PCI: cadence: Use struct pci_host_bridge.windows list directly
# Conflicts:
# drivers/pci/controller/cadence/pcie-cadence-host.c
- Set up mvebu BAR 0 so MSI works even if bootloader doesn't do this
(Shmuel Hazan)
* remotes/lorenzo/pci/mvebu:
PCI: mvebu: Setup BAR0 in order to fix MSI
- Fix loongson class code quirk so it happens early enough (Tiezhu Yang)
* remotes/lorenzo/pci/loongson:
PCI: loongson: Use DECLARE_PCI_FIXUP_EARLY for bridge_class_quirk()
- Fix hv timing issue that causes kdump failures (Wei Hu)
- Make some hv functions static (Wei Yongjun)
* remotes/lorenzo/pci/hv:
PCI: hv: Make some functions static
PCI: hv: Fix a timing issue which causes kdump to fail occasionally
- Convert cadence to use standard "dma-ranges" DT property instead of its
own "cdns,no-bar-match-nbits" (Kishon Vijay Abraham I)
- Fix pm_runtime_put_sync() issues in cadence error paths (Kishon Vijay
Abraham I)
- Add PTR_ALIGN_DOWN macro (Kishon Vijay Abraham I)
- Convert cadence r/w accessors to only 32-bit accesses (Kishon Vijay
Abraham I)
- Add cadence support to start Link and check Link status (Kishon Vijay
Abraham I)
- Allow custom PCI ops for cadence-based drivers (Kishon Vijay Abraham I)
- Remove "mem" from cadence reg binding since it's not memory and it
overlaps the PCIe config and memory region (Kishon Vijay Abraham I)
- Add cadence ->cpu_addr_fixup() for platforms that require absolute
addresses in the ATU, not just offsets (Kishon Vijay Abraham I)
- Update cadence Vendor IDs using local management registers, not
architected config space (Kishon Vijay Abraham I)
- Add cadence endpoint driver MSI-X support (Kishon Vijay Abraham I)
- Add bindings and driver for TI J721E SoC, supporting both host and
endpoint mode (Kishon Vijay Abraham I)
* remotes/lorenzo/pci/cadence:
MAINTAINERS: Add Kishon Vijay Abraham I for TI J721E SoC PCIe
misc: pci_endpoint_test: Add J721E in pci_device_id table
PCI: j721e: Add TI J721E PCIe driver
dt-bindings: PCI: Add EP mode dt-bindings for TI's J721E SoC
dt-bindings: PCI: Add host mode dt-bindings for TI's J721E SoC
PCI: cadence: Add MSI-X support to Endpoint driver
PCI: cadence: Fix updating Vendor ID and Subsystem Vendor ID register
PCI: cadence: Add new *ops* for CPU addr fixup
dt-bindings: PCI: cadence: Remove "mem" from reg binding
PCI: cadence: Allow pci_host_bridge to have custom pci_ops
PCI: cadence: Add support to start link and verify link status
PCI: cadence: Convert all r/w accessors to perform only 32-bit accesses
linux/kernel.h: Add PTR_ALIGN_DOWN macro
PCI: cadence: Fix cdns_pcie_{host|ep}_setup() error path
PCI: cadence: Use "dma-ranges" instead of "cdns,no-bar-match-nbits" property
Add support for Versal CPM as Root Port.
The Versal ACAP devices include CCIX-PCIe Module (CPM). The integrated
block for CPM along with the integrated bridge can function as PCIe Root
Port.
Bridge error and legacy interrupts in Versal CPM are handled using Versal
CPM specific interrupt line.
[bhelgaas: fold in kerneldoc fix from
https://lore.kernel.org/linux-acpi/20200729201224.26799-7-krzk@kernel.org/]
Link: https://lore.kernel.org/r/1592312214-9347-3-git-send-email-bharat.kumar.gogada@xilinx.com
Signed-off-by: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
The majority of DT based host drivers use the default .map_irq() and
.swizzle_irq() functions, so let's initialize the function pointers to
the default and drop setting them in the host drivers.
Drivers like iProc which don't support legacy interrupts need to set
.map_irq() back to NULL.
Link: https://lore.kernel.org/r/20200722022514.1283916-20-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Now that pci_parse_request_of_pci_ranges() callers just setup
pci_host_bridge.windows and dma_ranges directly and don't need the bus
range returned, we can just initialize them when allocating the
pci_host_bridge struct.
With this, pci_parse_request_of_pci_ranges() becomes a static function.
Link: https://lore.kernel.org/r/20200722022514.1283916-19-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The rcar-gen2 host driver still uses the old Arm PCI setup function
pci_common_init_dev(). Let's update it to use the modern
devm_pci_alloc_host_bridge(), pci_parse_request_of_pci_ranges() and
pci_host_probe() functions.
Link: https://lore.kernel.org/r/20200722022514.1283916-18-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-renesas-soc@vger.kernel.org
