The TI CPTS does not natively support PTPv1, only PTPv2. But, as it
happens, the CPTS can provide HW timestamp for PTPv1 Sync messages, because
CPTS HW parser looks for PTP messageType id in PTP message octet 0 which
value is 0 for PTPv1. As result, CPTS HW can detect Sync messages for PTPv1
and PTPv2 (Sync messageType = 0 for both), but it fails for any other PTPv1
messages (Delay_req/resp) and will return PTP messageType id 0 for them.
The commit e9523a5a32 ("net: ethernet: ti: cpsw: enable
HWTSTAMP_FILTER_PTP_V1_L4_EVENT filter") added PTPv1 hw timestamping
advertisement by mistake, only to make Linux Kernel "timestamping" utility
work, and this causes issues with only PTPv1 compatible HW/SW - Sync HW
timestamped, but Delay_req/resp are not.
Hence, fix it disabling PTPv1 hw timestamping advertisement, so only PTPv1
compatible HW/SW can properly roll back to SW timestamping.
Fixes: e9523a5a32 ("net: ethernet: ti: cpsw: enable HWTSTAMP_FILTER_PTP_V1_L4_EVENT filter")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20201029190910.30789-1-grygorii.strashko@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The previous patch has introduced possibility to select CPSW ALE by using
ALE dev_id identifier. Switch TI cpsw driver to use dev_id="cpsw" and
perform clean up by removing "ale_entries" configuration code.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that BPF program/link management is centralized in generic net_device
code, kernel code never queries program id from drivers, so
XDP_QUERY_PROG/XDP_QUERY_PROG_HW commands are unnecessary.
This patch removes all the implementations of those commands in kernel, along
the xdp_attachment_query().
This patch was compile-tested on allyesconfig.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200722064603.3350758-10-andriin@fb.com
The MSCC bug fix in 'net' had to be slightly adjusted because the
register accesses are done slightly differently in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
cpsw_ale_create() can return both NULL and PTR_ERR(), but all of
the caller only check NULL for error handling. This patch convert
it to only return PTR_ERR() in all error cases, and the caller using
IS_ERR() instead of NULL test.
Fixes: 4b41d34367 ("net: ethernet: ti: cpsw: allow untagged traffic on host port")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPSW misc IRQ need be enabled for CPTS event_pend IRQs processing. This
patch adds corresponding support to CPSW driver.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hence CPTS IRQ support is in place the W_TS_PUSH events can be added.
PWM capable DmTimers can be used to generete input signals for CPTS on TI
AM335x/AM437x/DRA7 SoCs to be timestamped:
AM335x/AM437x: timer4 - timer7
DRA7/AM57xx: timer13 - timer16
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now RX interrupt is triggered twice every time, because in
cpsw_rx_interrupt() it is asked first and then disabled. So there will be
pending interrupt always, when RX interrupt is enabled again in NAPI
handler.
Fix it by first disabling IRQ and then do ask.
Fixes: 870915feab ("drivers: net: cpsw: remove disable_irq/enable_irq as irq can be masked from cpsw itself")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Part 1:
Introduce basic CPSW dual_mac driver (cpsw_new.c) which is operating in
dual-emac mode by default, thus working as 2 individual network interfaces.
Main differences from legacy CPSW driver are:
- optimized promiscuous mode: The P0_UNI_FLOOD (both ports) is enabled in
addition to ALLMULTI (current port) instead of ALE_BYPASS. So, Ports in
promiscuous mode will keep possibility of mcast and vlan filtering, which
is provides significant benefits when ports are joined to the same bridge,
but without enabling "switch" mode, or to different bridges.
- learning disabled on ports as it make not too much sense for
segregated ports - no forwarding in HW.
- enabled basic support for devlink.
devlink dev show
platform/48484000.switch
devlink dev param show
platform/48484000.switch:
name ale_bypass type driver-specific
values:
cmode runtime value false
- "ale_bypass" devlink driver parameter allows to enable
ALE_CONTROL(4).BYPASS mode for debug purposes.
- updated DT bindings.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparatory patch to add support for a switchdev based cpsw driver,
move common functions to cpsw-priv.c so that they can be used across both
drivers.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A following patches introduce new CPSW switchdev driver which uses common
code with legacy CPSW driver. This will introduce build dependency between
CPSW switchdev and CPSW legacy drivers related to for_each_slave() and
cpsw_slave_index() - they can be compiled both, but only one of them will
be not functional depending in Kconfig settings due to duffrences in Slave
Ports indexes calculation.
To fix this make for_each_slave() local (it's used now only by legacy CPSW
driver) and convert cpsw_slave_index() to be a function pointer which is
assigned in probe. Driver to probe is defined by DT.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
move common hw init code in separate function as preparation for adding new
switchdev driver.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
